Rigol | DG1000Z Series | DG1000Z Datasheet

DG1000Z Series
Function/Arbitrary
Waveform Generator
SiFi (Signal Fidelity) for 100% waveform replication
8Mpts (standard) or 16Mpts (optional) arbitrary waveform memory
length for each channel
Standard 2 full functional independent channels
±1ppm frequency stability, -125dBc/Hz phase noise, 200ps low jitter
Built-in 8 orders harmonics generator
Built-in 7 digits/s counter up to 200MHz
160 built-in pre-edited waveforms
Intuitive arbitrary waveform editing software.
Full modulation supported: AM, FM, PM, ASK, FSK, PSK and PWM
DG1000Z series function/arbitrary waveform generator is a multifunctional generator that combines many functions in one, including
Function Generator, Arbitrary Waveform Generator, Noise Generator,
Pulse Generator, Harmonics Generator, Analog/Digital Modulator and
Counter. As a multi-functional, high performance and portable generator,
it will be a new selection in education, R&D, production, test and etc.
RIGOL TECHNOLOGIES, INC.
DG1000Z Series Function/Arbitrary Waveform Generator
Dimensions: Width×Height×Depth=261.5mm×112mm×318.4mm
Weight: 3.2kg (without package)
1 RIGOL
Feature and Benefits
Standard 2 full functional channels
Arbitrary waveform function with
innovative SiFi technology
Up to 160 built-in waveforms
Burst function
Multiple analog and digital modulations
Sweep function
Standard harmonic generator
Waveform summing function
Standard 7 digits/s full function frequency
counter with 200MHz bandwidth
Channels and system setting
In line with LXI Core Device 2011
File Management Function
RIGOL
2
Specifications
All the specifications can be guaranteed if the following two conditions are met unless where noted.
· The generator is within the calibration period and has performed self-calibration.
· The generator has been working continuously for at least 30 minutes under the specified temperature (18℃ ~ 28℃ ).
All the specifications are guaranteed unless those marked with “typical”.
Model
Channel
Max Frequency
Sample Rate
Waveform
Basic Waveform
Built-in Arbitrary Waveform
DG1032Z
2
30 MHz
200 MSa/s
DG1062Z
2
60 MHz
Sine, Square, Ramp, Pulse, Noise
160 kinds, including Sinc, Exponential Rise, Exponential Fall, ECG, Gauss, HaverSine, Lorentz,
Dual-Tone, etc.
Frequency Characteristics
Sine
Square
1 μHz to 30 MHz
1 μHz to 15 MHz
1 μHz to 60MHz
1 μHz to 25 MHz
Ramp
1 μHz to 500kHz
1 μHz to 1MHz
Pulse
Harmonic
Noise (-3dB)
Arbitrary Waveform
Resolution
Accuracy
1 μHz to 15 MHz
1uHz to 10MHz
30 MHz bandwidth
1 μHz to 10 MHz
1 μHz
±1 ppm of the setting value, 18℃ to 28℃
1 μHz to 25 MHz
1uHz to 20MHz
60 MHz bandwidth
1 μHz to 20 MHz
Sine Wave Spectrum Purity
Harmonic Distortion
Total Harmonic Distortion
Spurious (non-harmonic)
Phase Noise
Signal Characteristics
Square
Rise/Fall Time
Overshoot
Duty Cycle
Non-symmetry
Jitter (rms)
Ramp
Linearity
Symmetry
Pulse
Pulse Width
Duty Cycle
Rising/Falling Edge
Overshoot
Jitter (rms)
Arbitrary Waveform
Waveform Length
Vertical Resolution
3 RIGOL
Typical (0 dBm)
DC-10 MHz (included):
<-65 dBc
10 MHz to 30 MHz (included):
<-55 dBc
30 MHz to 60 MHz (included):
<-50 dBc
<0.075% (10 Hz to 20 kHz, 0 dBm)
Typical (0 dBm)
≤10 MHz <-70 dBc
>10 MHz <-70 dBc + 6 dB/octave
Typical (0 dBm, 10 kHz offset)
10 MHz: <-125 dBc/Hz
Typical (1 Vpp)
<10ns
Typical (100 kHz, 1 Vpp)
≤5%
0.01% to 99.99% (limited by the current frequency setting)
1% of the period + 5 ns
Typical (1 Vpp)
≤5 MHz 2 ppm + 200 ps
> 5 MHz 200 ps
≤1% of peak output (typical, 1 kHz, 1 VPP, 100% symmetry)
0% to 100%
≥16 ns (limited by the current frequency setting)
0.001% to 99.999% (limited by the current frequency setting)
≥10 ns (limited by the current frequency setting and pulse width setting)
Typical (1 Vpp)
≤5%
Typical (1 Vpp)
≤5 MHz 2 ppm + 200 ps
> 5 MHz 200 ps
8pts to 8Mpts (16Mpts optional)
14 bits
Sample Rate
Min Rise/Fall Time
Jitter (rms)
Editing Mode
Harmonic Output
Harmonic Order
Harmonic Type
Harmonic Amplitude
Harmonic Phase
Output Characteristics
Amplitude (into 50 Ω)
Range
Accuracy
Flatness
Unit
Resolution
Offset (into 50 Ω)
Range (Peak ac+dc)
Accuracy
Waveform Output
Output Impedance
Protection
Modulation Characteristics
Modulation Type
AM
Carrier Waveform
Source
Modulating Waveform
Modulation Depth
Modulating Frequency
FM
Carrier Waveform
Source
Modulating Waveform
Modulating Frequency
PM
Carrier Waveform
Source
Modulating Waveform
Phase Deviation
Modulating Frequency
ASK
Carrier Waveform
Source
Modulating Waveform
Key Frequency
FSK
Carrier Waveform
Source
Modulating Waveform
Key Frequency
PSK
Carrier Waveform
Source
Modulating Waveform
200MSa/s
Typical (1 Vpp)
<10 ns
Typical (1 Vpp)
≤5 MHz 2 ppm + 200 ps
> 5 MHz 200 ps
Point Edit, Block Edit, Insert Built-in Waveform
≤8
Even Harmonic, Odd harmonic, Order Harmonic, User
The amplitude of each order of harmonic can be set
The phase of each order of harmonic can be set
≤10 MHz: 2.5 mVpp to 10 Vpp
≤30 MHz: 2.5 mVpp to 5.0 Vpp
≤60 MHz: 2.5 mVpp to 2.5 Vpp
Typical (1 kHz sine, 0 V offset, >10 mVpp, auto)
±(1% of the setting value) ±1 mV
Typical (sine, 2.5 Vpp)
≤10 MHz
±0.1 dB
≤60 MHz
±0.2 dB
Vpp, Vrms, dBm
0.1mVpp or 4 digits
±5 V
±(1% of the setting value + 5mV + 0.5% of the amplitude)
50 Ω (typical)
Short-circuit protection, automatically disable the waveform output when overload occurs
AM, FM, PM, ASK, FSK, PSK, PWM
Sine, Square, Ramp, Arb (except DC)
Internal/External
Sine, Square, Ramp, Noise, Arb
0% to 120%
2 mHz to 1 MHz
Sine, Square, Ramp, Arb (except DC)
Internal/External
Sine, Square, Ramp, Noise, Arb
2 mHz to 1 MHz
Sine, Square, Ramp, Arb (except DC)
Internal/External
Sine, Square, Ramp, Noise, Arb
0° to 360°
2 mHz to 1 MHz
Sine, Square, Ramp, Arb (except DC)
Internal/External
Square with 50% duty cycle
2 mHz to 1 MHz
Sine, Square, Ramp, Arb (except DC)
Internal/External
Square with 50% duty cycle
2 mHz to 1 MHz
Sine, Square, Ramp, Arb (except DC)
Internal/External
Square with 50% duty cycle
RIGOL
4
Key Frequency
PWM
Carrier Waveform
Source
Modulating Waveform
Width Deviation
Modulating Frequency
External Modulation Input
Input Range
Input Bandwidth
Input Impedance
2 mHz to 1 MHz
Pulse
Internal/External
Sine, Square, Ramp, Noise, Arb
0% to 100% of the pulse width
2 mHz to 1 MHz
75 mVRMS to ±5 Vac + dc
50 kHz
10KΩ
Burst Characteristics
Carrier Waveform
Carrier Frequency
Burst Count
Start/Stop Phase
Internal Period
Gated Source
Trigger Source
Trigger Delay
Sine, Square, Ramp, Pulse, Noise, Arb (except DC)
2 mHz to 30 MHz
2 mHz to 60 MHz
1 to 1,000,000 or Infinite
0° to 360°
1 μs to 500 s
External Trigger
Internal, External or Manual
0 ns to 100 s
Sweep Characteristics
Carrier Waveform
Type
Direction
Start/Stop Frequency
Sweep Time
Hold/Return Time
Trigger Source
Marker
Sine, Square, Ramp, Arb (except DC)
Linear, Log or Step
Up or Down
The same with the upper/lower limit of the corresponding carrier frequency
1 ms to 500 s
0 ms to 500 s
Internal, External or Manual
Falling edge of the sync signal (programmable)
Frequency Counter
Function
Frequency, Period, Positive/Negative Pulse Width, Duty Cycle
Frequency Resolution
7 digits/second (Gate Time = 1s)
Frequency Range
1 μHz to 200 MHz
Period Measurement
Measurement Range
5ns to 16 days
Voltage Range and Sensitivity (non-modulating signal)
DC Offset Range
±1.5 Vdc
DC Coupling
1μHz to 100 MHz
50 mVRMS to ±2.5 Vac + dc
100 MHz to 200 MHz
100 mVRMS to ±2.5 Vac + dc
1 μHz to 100 MHz
50 mVRMS to ±2.5 Vpp
AC Coupling
100 MHz to 200 MHz
100 mVRMS to ±2.5 Vpp
Pulse Width and Duty Cycle Measurement
Frequency and Amplitude
1 μHz to 25 MHz
50 mVRMS to ±2.5 Vac + dc
Ranges
Min Pulse Width
≥20 ns
DC Coupling
Pulse Width
Pulse Width Resolution
5 ns
Duty Cycle
Measurement Range (display)
0% to 100%
Input Characteristics
Input Signal Range
Breakdown Voltage
±7Vac+dc
Input Impedance = 1 MΩ
Coupling Mode
AC
DC
Input Adjustment
On: Input Bandwidth = 250 kHz;
High-frequency Rejection
Off: Input Bandwidth = 200 MHz
Trigger Level Range
-2.5V to +2.5V
Input Trigger
0% (about 140 mV hysteresis voltage) to 100% (about 2 mV
Trigger Sensitivity Range
hysteresis voltage)
GateTime1
1.310ms
GateTime2
10.48ms
GateTime3
166.7ms
Gate Time
GateTime4
1.342s
GateTime5
10.73s
GataTime6
>10s
5 RIGOL
Trigger Characteristics
Trigger Input
Level
Slope
Pulse Width
Latency
Trigger Output
Level
Pulse Width
Maximum Frequency
Reference Clock
Phase Offset
Range
Resolution
External Reference Input
Lock Range
Level
Lock Time
Input Impedance (Typical)
Internal Reference Output
Frequency
Level
Input Impedance (Typical)
Sync Output
Level
Impedance
TTL-compatible
Rising or falling (selectable)
>100ns
Sweep: <100 ns (typical)
Burst: <300 ns (typical)
TTL-compatible
> 60 ns (typical)
1 MHz
0° to 360°
0.03°
10 MHz ± 50 Hz
250 mVpp to 5 Vpp
<2s
1 kΩ, AC coupling
10 MHz ± 50 Hz
3.3 Vpp
50 Ω, AC coupling
TTL-compatible
50 Ω, nominal value
Overvoltage Protection
Occurred when:
 The instrument amplitude setting is greater than 2Vpp or the output offset is greater than |2VDC| and the input voltage is greater
than ±11.5 × (1 ± 5%)V (<10kHz).
 The instrument amplitude setting is lower than or equal to 2Vpp or the output offset is lower than or equal to |2VDC| and the
input voltage is greater than ±3.5 × (1 ± 5%)V (<10kHz).
General Specifications
Power Supply
Power Voltage
Power Consumption
Fuse
Display
Type
Resolution
Color
Environment
Temperature Range
Cooling Method
Humidity Range
Altitude
Mechanical
Dimensions (W×H×D)
Weight
Interfaces
IP Protection
Calibration Interval
100 V to 240 V (45 Hz to 440 Hz)
Lower than 40 W
250 V, T3.15 A
3.5-inch TFT LCD
320 horizontal × RGB × 240 vertical resolution
16 M color
Operating: 0℃ to 50℃
Non-operating: -40℃ to 70℃
Fan cooling
Lower than 30℃ : ≤95% relative humidity
30℃ to 40℃ : ≤75% relative humidity
40℃ to 50℃ : ≤45% relative humidity
Operating: below 3000 meters
Non-operating: below 15,000 meters
261.5 mm × 112 mm × 318.4 mm
Without Package: 3.2 kg
With Package: 4.5 kg
USB Host, USB Device, LAN
IP2X
1 year recommended calibration interval
RIGOL 6
Certification Information
in line with EN61326-1:2006
±4.0kV (contact discharge)
±4.0kV (air discharge)
3 V/m (80 MHz to 1 GHz)
3 V/m (1.4 GHz to 2 GHz)
1 V/m (2.0 GHz to 2.7 GHz)
1 kV power lines
0.5kV (Phase to Neutral)
0.5kV (Phase to PE)
1 kV (Neutral to PE)
3V,0.15MHz-80MHz
Voltage dip:
0 % UT during half cycle
0 % UT during 1 cycle
70 % UT during 25 cycles
Short interruption:
0 % UT during 250 cycles
IEC 61000-3-2:2000
IEC 61000-4-3:2002
IEC 61000-4-4:2004
EMC
IEC 61000-4-5:2001
IEC 61000-4-6:2003
IEC 61000-4-11:2004
Electrical Safety
Electrical Safety
in line with
USA:UL 61010-1:2012,
Canada: CAN/CSA-C22.2 No. 61010-1-2012
EN 61010-1:2010
Ordering Information
Model
Standard Accessories
Options
Headquarter
RIGOL TECHNOLOGIES, INC.
No.156,Cai He Village,
Sha He Town,
Chang Ping District, Beijing,
102206 P.R.China
Tel:+86-10-80706688
Fax:+86-10-80705070
Email: support@rigol.com
Description
DG1032Z (30MHz, Dual-channel)
DG1062Z (60MHz, Dual-channel)
Power Cord
USB Cable
BNC Cable
Quick Guide
Order Number
DG1032Z
DG1062Z
CB-USBA-USBB-FF-150
CB-BNC-BNC-MM-100
-
Resource CD (including User’s Guide and etc.)
-
16Mpts Memory for Arb
Rack Mount Kit (for single instrument)
Rack Mount Kit (for dual instruments)
40dB Attenuator
10W Power Amplifier
USB-GPIB Converter
Arb16M-DG1000Z
RM-1-DG1000Z
RM-2-DG1000Z
RA5040K
PA1011
USB-GPIB
USA
RIGOL TECHNOLOGIES
USA,INC.
7401 First Place,Suite N
Oakwood Village
OH 44146,USA
Tel/Fax: 440-232-4488
Toll free: 877-4-RIGOL-1
Email: info@rigol.com
Europe
RIGOL TECHNOLOGIES EU,
GmbH
Lindbergh str. 4
82178 Puchheim, Germany
Tel: +49(0)89-8941895-0
Email: info-europe@rigol.com
RIGOL® is the registered trademark of RIGOL Technologies, Inc. Product information in this document subject to update without notice. For the
latest information about RIGOL's products, applications and services, please contact local RIGOL office or access RIGOL official website:
www.rigol.com
V01-14
Download PDF