AXIOMTEK | Dk3g4PANEL 6153-O/P | User`s manual | AXIOMTEK Dk3g4PANEL 6153-O/P User`s manual

Dk3g4PANEL 6153-O/P
15” INDUSTRIAL TFT LCD MONITOR
User’s Manual
Disclaimers
The information in this manual has been carefully checked and is believed to be
accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of
patents or other rights of third parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in
this document. AXIOMTEK makes no commitment to update or to keep current the
information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of AXIOMTEK Co.,
Ltd.
©Copyright 2006 by AXIOMTEK Co. Ltd.,
All rights reserved.
June 2006, Version A1
Printed in Taiwan
ii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
iii
Safety Precautions
Before getting started, read the following important cautions.
1.
2.
3.
4.
5.
6.
7.
iv
The P6153 does not come equipped with an operating system. An
operating system must be loaded first before installing any software
into the computer.
Be sure to ground yourself to prevent static charge when installing
the internal components. Use a grounding wrist strap and place all
electronic components in any static-shielded devices. Most
electronic components are sensitive to static electrical charge.
Disconnect the power cord from the P6153 before making any
installation. Be sure both the system and the external devices are
turned OFF. Sudden surge of power could ruin sensitive components.
Make sure the P6153 is properly grounded.
The brightness of the flat panel display decreases with usage.
However, hours of use vary depending on the application
environment.
Turn OFF the system power before cleaning. Clean the system using
a cloth only. Do not spray any liquid cleaner directly onto the screen.
The P6153 may come with or without a touchscreen. Although the
touchscreen is chemical resistant, it is recommended that you spray
the liquid cleaner on a cloth first before wiping the screen. In case
your system comes without the touchscreen, you must follow the
same procedure and not spray any cleaner on the flat panel directly.
Avoid using sharp objects to operate the touchscreen. Scratches on
the touchscreen may cause malfunction or internal failure to the
touchscreen.
The flat panel display is not susceptible to shock or vibration. When
assembling the P6153, make sure it is securely installed.
8.
Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do so.
Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
v
This page does not contain any information.
vi
Table of Contents
Chapter 1 Introduction ..................... 1
1.1
1.2
1.3
1.4
1.5
General Description ........................................... 1
Features ............................................................. 2
Specifications .................................................... 2
Dimensions ........................................................ 3
I/O Inputs ........................................................... 5
Chapter 2 System Setup..................... 7
2.1
2.2
2.3
2.4
2.5
System Configuration ........................................ 7
Panel Mounting .................................................. 9
Wall Mounting (Option).................................... 11
Rack Mounting (Option)................................... 13
Desktop Stand (Option) ................................... 14
Appendix A Supported Input Timing
Modes ........................... 16
Appendix B OSD Operation ............... 17
Table of Contents
vii
This page does not contain any information.
viii
Chapter
1
Introduction
This chapter contains the general information and the detailed
specifications of the P6153-O/P. Chapter 1 includes the following
sections:
General Description
Features
System Specification
Dimensions
I/O Inputs
1.1
General Description
The Panel6153, a industrial 15.0 inches view area LCD Monitor
comes with slim, light and reliable features to replace traditional bulky
CRT for industrial application. Its unique front side design is fit for
open frame mounting (Panel6153-O) or panel mounting
(Panel6153-P). The display interface offers VGA-in, DVI, S-Video,
Video standard interfaces for different input source from PC system or
multimedia system that let you upgrade the display don’t change
anything from your system. Besides, for varied HMI field, you can
choose one of resistive, capacitive touch screen or glass interface to
meet your application. In addition, this monitor has more comfort,
safety, and environmental protection for humanized & health
consideration those would be the benefit that users can get.
This LCD monitor builds in 15.0” color active matrix thin-film-transistor
(TFT) liquid crystal display to provide superior display performance. A
maximum resolution of 1024x768 is ideal for displaying complex
graphics and high definition images. Other outstanding designs that
enhance this LCD monitor ’s performance are Plug & Play
compatibility, and OSD (On Screen Display) controls, especially OSD,
it made you ease adjustment on screen image.
Introduction
1
1.2
Features
High contrast color 15.0” SXGA TFT LCD display support
resolution up to 1024x768
Heavy-duty steel chassis with NEMA4/IP65-compliant
Suits with resistive, capacitive or tempered
anti-reflection glass
Multi-scan function supports XGA, SVGA, VGA,
VGA-Text, PC-9801, MAC.
High Brightness and Ultra-wide viewing angle with
anti-glare features
Power management system conforms to VESA DPMS
standard
Advanced OSD control for picture quality adjustment
Supports VESA ARMS, Desktop Stand
Rear, Panel, Wall or Rack mounting
1.3
Specifications
Construction: Heavy-duty steel chassis
Control: OSD (On Screen Display) control pad on front
side
Mounting: Support Panelmount, VESA arm mounting,
Rackmount(optional), and Wallmount(optional)
Net weight: 5.1Kgs for P6153PR
Dimension (main body size):
- P6153-P
400.0X323.0X45.5 mm
- P6153-O
400.0X323.0X45.5 mm
Operating Temperature Range: 0 o C ~ 50 o C
Relative Humidity: 20% ~ 90%; non-condensing
2
1.4
Dimensions
Introduction
3
4
1.5 I/O Inputs
P6153-P/ P6153-O Inputs
1.
T/S Port (D-sub optional): This connector will be present only if a
touchscreen is installed. It must be connected to the RS-232 port of the
PC. The touchscreen cable is included with all orders, which include the
touchscreen optio
2.
DC +12V: This connector will be connected to the DC 12V Switching
Power Supply.
3.
DVI Port: This connector can be connected to the system via the
external DVI connector located on the bottom side of the system unit.
4.
VGA Port (D-sub): This D-Sub15 connector can be connected to the
system via the external D-Sub15 connector located on the bottom side of
the system unit.
5.
AV Port: This connector can be connected to the system via the external
connector located on the bottom side of the system unit.
6.
S-Video Port: This connector can be connected to the system via the
external connector located on the bottom side of the system unit.
Remark: P6153 only support one display input. Please do not
plug-in multiple display input at one time.
Introduction
5
This page does not contain any information.
6
P6153 Series Panel PC User’s Manual
Chapter
2
System Setup
This chapter details the system parts and components with figures.
Sections include
Rack Mounting
System Configuration
Desktop Stand
Panel Mounting
Wall Mounting
2.1
System Configuration
The figure below shows the front views of P6153 series.
System Setup
7
P6153 Series Panel PC User’s Manual
1.
2.
6.
Power switch: Press this button to turn on/off the monitor.
Power LED: When the light is green, the power is on, flash when the
power is active off.
SEL+:
- To scroll up the menu.
- To increase the value of selected item.
SEL-:
- To scroll down the menu.
- To decrease the value of selected item.
Menu:
- Press this button to turn on/off the OSD (On Screen Display)
main menu.
- Press this button to activate selected items.
Exit: Jump out the selection icon.
8
System Setup
3.
4.
5.
P6153 Series Panel PC User’s Manual
2.2
Panel Mounting
Panel
Two accessory items are needed for this application.
Mounting bracket x 6 pcs
Pan head screws (M4x0.7PxL45.0mm) x 6 pcs
Installation instruction
1.
2.
3.
Find a plate and cut off a window, refer the 1.4 P6153-P Dimensions
for the dimension.
Screw the mounting bracket to the unit.
Combine flange nuts with box head screws and then screw to the
mounting bracket to tighten the unit.
System Setup
9
P6153 Series Panel PC User’s Manual
Note: To obtain the maximum degree of moisture resistance, be sure to
mount the P6153 on a smooth, flat surface.
The panel itself can be from 1.6 to 16.0mm thick.
Strengthening may be required for the panel. Be sure to consider the
weight of the P6153 when designing the panel.
1.6~16mm
Note: To enhance the P6153’s maintainability, operability and ventilation,
allow at least 35mm clearance between the P6153 and any other
objects. (The clearance must be large enough to allow you to insert
or remove expansion boards and to attach connectors.)
10
System Setup
P6153 Series Panel PC User’s Manual
Side View
35.0
35.0
Rear View
35.0
35.0
35.0
35.0
35.0
Unit: mm
2.3
Wall Mounting (Option)
Wall
Bracket
The unit is designed to support wall mounting application. It let you
to mount the unit on the wall.
Three accessory items to support this feature.
Wall mounting bracket x 1 pcs
System Setup
11
P6153 Series Panel PC User’s Manual
Binding head & washer screws (M4x0.7PxL6.0mm) x 4 pcs
Truss head screws (TTS-4, 3.5x10mm-black) x 4 pcs
Installation instruction
1.
2.
3.
12
Refer the hole location on the page 3. Screw the truss head screws to
the hole location on the wall.
Note: Do not tight the screw for mounting the unit. The minimum
space between the wall and the top of screw is 1.6mm.
Mount the wall mounting bracket to the back cover of the unit.
Mount the unit to the wall.
System Setup
P6153 Series Panel PC User’s Manual
2.4
Rack Mounting
Installation instruction
1.
2.
Remove 8 seal pads in front panel.
P6153 series products could to mount directly to standard 19” industrial
rack. There are four screw holes on each side of front panel.
System Setup
13
P6153 Series Panel PC User’s Manual
2.5
Desktop Stand (Option)
5.000
Side View
The unit is designed to support desktop stand application.
Two accessory items are needed for this application.
Wall mounting bracket x 1 pcs
Binding head & washer screws (M4x0.7PxL6.0mm) x 2 pcs
Installation instruction
Mounting the wall mounting bracket with the binding header & washer
screws to the back over of the unit and then the unit can stand on the
desktop.
14
System Setup
P6153 Series Panel PC User’s Manual
This page does not contain any information.
System Setup
15
P6153 Series Panel PC User’s Manual
Appendix
A
Supported Input Timing Modes
Supported Input Timing Modes
The following timings below are already programmed in this module.
The input synchronous signals are automatically recognized.
16
Preset No.
Display Size
Vsync (Hz)
1
640x350
70
2
640x400
70
3
640x480
60
4
640x480
72
5
640x480
75
6
720x400
70
7
800x600
60
8
800x600
72
9
800x600
75
10
1024x768
60
11
1024x768
70
12
1024x768
75
Supported Input Timing Modes
P6153 Series Panel PC User’s Manual
Appendix
B
OSD Operation
Function Description of OSD Menu
Main Screen
OSD Operation
17
P6153 Series Panel PC User’s Manual
Signal Select
VGA Input
Setting Monitor’s Input to VGA
DVI Input
Setting Monitor’s Input to DVI
AV Input
Setting Monitor’s Input to AV
S-Video Input
Setting Monitor’s Input to S-Video
Exit
Exit the LCD Setting
18
OSD Operation
P6153 Series Panel PC User’s Manual
Video Adjust
Brightness Adjust
Adjust Monitor’s Brightness
Use ▲ or ▼ button to increase or decrease the
setting.
Contrast Adjust
Adjust Monitor’s Contrast
Use ▲ or ▼ button to increase or decrease the
setting.
Exit
Exit the LCD Setting
OSD Operation
19
P6153 Series Panel PC User’s Manual
Audio Adjust: P6153 doesn’t support Audio.
20
OSD Operation
P6153 Series Panel PC User’s Manual
Color Adjust
Automatically Color Tuning
Monitor will automatically tune the color setting.
Manually Color Tuning
Adjust color setting
Use ▲ or ▼ button to increase or decrease the
setting.
Exit
Exit the LCD Setting
OSD Operation
21
P6153 Series Panel PC User’s Manual
Image Adjust
Automatically Image Tuning
Monitor will automatically tune the image setting.
Horizontal Width Adjust
Adjust Monitor’s horizontal width setting.
Use ▲ or ▼ button to increase or decrease the
setting.
Horizontal Phase Adjust
Adjust Monitor’s horizontal phase setting.
Use ▲ or ▼ button to increase or decrease the
setting.
22
OSD Operation
P6153 Series Panel PC User’s Manual
Horizontal Position Adjust
Adjust horizontal position setting.
Use ▲ or ▼ button to increase or decrease the
setting.
Vertical Position Adjust
Adjust vertical position setting.
Use ▲ or ▼ button to increase or decrease the
setting.
Exit
Exit the LCD Setting
OSD Operation
23
P6153 Series Panel PC User’s Manual
Image Adjust
OSD Setting
Adjust OSD setting.
Recall Previous Setting
Monitor will recall the previous setting.
Sharpness Adjust
Adjust Monitor’s sharpness setting.
Use ▲ or ▼ button to increase or decrease the
setting.
24
OSD Operation
P6153 Series Panel PC User’s Manual
This page does not contain any information.
25
Download PDF