Quick Reference Guide

Quick Reference Guide
Quick Reference Guide
COLORband PiX™ Mini QRG
About This
Guide
The COLORband PiX™ Mini Quick Reference Guide (QRG) contains the
product’s connection and mounting information, as well as the menu
options and the DMX values.
•
Disclaimer
Safety Notes
•
Refer to this product’s User Manual for detailed information and
instructions. You can download the User Manual from the
CHAUVET® website: www.chauvetlighting.com.
Read ALL the disclaimers and Safety Notes in this document as well as
those in the product’s User Manual before installing, operating, or
maintaining this product.
These Safety Notes include important safety information about installation,
usage, and maintenance.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Always connect this product to a grounded circuit to avoid the risk of
electrocution.
Always disconnect from the power source before cleaning this product
or replacing the fuse.
Avoid direct eye exposure to the light source while the product is on.
Make sure the power cord is not crimped or damaged.
If mounting this product overhead, always secure it to a fastening
device using a safety cable.
Make sure there are no flammable materials close to the unit while
operating.
Do not touch this product’s housing when operating because it may be
very hot.
Always make sure that the voltage of the outlet to which you are
connecting this product is within the range stated on the decal or rear
panel of the product.
This product is for indoor use only! (IP20) To prevent risk of fire or
shock, do not expose this product to rain or moisture.
Always install this product in a location with adequate ventilation, at
least 20 in (50 cm) from adjacent surfaces.
Be sure that no ventilation slots on the unit’s housing are blocked.
Never connect this product to a dimmer.
Make sure to replace the fuse with the same type and rating.
Never carry this product from the power cord or any moving part.
Always use the hanging/mounting bracket or the handles.
The maximum ambient temperature is 104° F (40° C). Do not operate
this product at higher temperatures.
In the event of a serious operating problem, stop using the unit
immediately.
Never try to repair this product. Repairs performed by unauthorized
technicians can lead to damage or malfunction. Please contact the
nearest authorized technical assistance center.
Page 2 of 12
COLORband PiX™ Mini QRG
What Is
Included
•
•
•
•
•
One COLORband PiX™ Mini
One Power Cord
Two L-Brackets
One Warranty Card
One Quick Reference Guide
Before You
Begin
Prior to using your COLORband PiX™ Mini, ensure that you have received
all parts indicated above in good condition. If the container or material
inside appear damaged or show signs of mishandling, notify the carrier
immediately, not CHAUVET®.
Product
Description
The COLORband PiX™ Mini is a half-sized LED strip light with
individual pixel control for pixel mapping effects. It includes multiple
DMX personalities to fit any programming style. The COLORband PiX™
Mini also includes high frequency LED dimming, allowing for flicker-free
video operation.
Power Out
Sound Sensitivity Knob
Microphone
Power In
LED Display
Product Overview
5-pin DMX In
Bracket Adjustment Knob
Page 3 of 12
3-pin DMX In
5-pin DMX Out
3-pin DMX Out
COLORband PiX™ Mini QRG
AC Power
This product has an auto-ranging power supply that can work with an input
voltage range of 100~240 VAC, 50/60 Hz.
Power Linking You can link up to 20 COLORband PiX™ Mini units at 120 VAC and 35
units at 230 VAC. You should never exceed this number.
Fuse To replace the fuse in the COLORband PiX™ Mini, use the following steps:
Replacement 1. Disconnect this product from the power outlet.
2.
3.
4.
5.
Wedge the tip of a flat head screwdriver into the slot of the fuse holder.
Pry the safety cap out of the housing pulling out the installed fuse.
Remove the blown fuse from the safety cap and replace with a fuse of
the exact same type and rating.
Insert the fuse holder back in place and reconnect power.
Page 4 of 12
COLORband PiX™ Mini QRG
Menu Options
Main Level
Programming Levels
C1
C2
C3
C4
C5
C6
C7
P1
P2
P3
P4
P5
P6
P7
S001-S100
Static Colors
C--
Auto Programs
P--
Program Speed
Slave Mode
S--
Custom Color Mixing
U--
r-g-b--
3-Channel Mode
4-Channel Mode
6-Channel Mode
7-Channel Mode
9-Channel Mode
18-Channel Mode
3-CH
4-CH
6-CH
7-CH
9-CH
18-CH
d001-d512
SLA
Page 5 of 12
Description
Red
Green
Blue
Cyan
Magenta
Yellow
White
7 Color Switching
7 Color Fading
3 Color Switching
3 Color Fading
Chase Program
7 Color Sound Active
7 Color Sound Active Chase + Strobe
Selects auto program speed
Sets Slave Mode
Red
Green
Blue
Selects DMX starting address
COLORband PiX™ Mini QRG
Programming
Control Panel
Description
For details on how to program this product, please refer to the product’s
User Manual.
Button
Function
<MENU> Exits from the current menu or function.
Navigates upwards through the menu list and increases the
<UP>
numeric value when in a function.
Navigates downwards through the menu list and decreases the
<DOWN>
numeric value when in a function.
Enables the currently displayed menu or sets the currently
<ENTER>
selected value into the selected function.
Page 6 of 12
COLORband PiX™ Mini QRG
DMX Linking
The COLORband PiX™ Mini can work with a DMX controller when linked
using a regular DMX serial connection.
If you are not familiar with the DMX standard, please download the DMX
Primer document from www.chauvetlighting.com.
DMX The COLORband PiX™ Mini uses a regular DMX data connection for its
Connection DMX personalities.
Download the COLORband PiX™ Mini User Manual. Refer to the Setup
chapter to learn how to connect this product for DMX operation. To learn
how to configure this product for DMX operation, refer to the Operation
chapter.
Start Address To ensure full access to all channels in each DMX mode, the highest
recommended DMX address is based on the channel mode. For example, if
using the 18-channel mode on the COLORband PiX™ Mini, the highest
channel you can use is 495.
Master/Slave The COLORband PiX™ Mini uses the DMX data connection for its
Connection Master/Slave mode.
Download the COLORband PiX™ Mini User Manual. Refer to the Setup
chapter to learn how to connect this product for Master/Slave operation. To
learn how to configure this product for Master/Slave operation, refer to the
Operation chapter.
Page 7 of 12
COLORband PiX™ Mini QRG
DMX Values
7-CH
Channel Function
1
2
3
Red
Green
Blue
4
Color Macros
5
3-CH
4-CH
Speed
000  255
Strobe
(CH.1-CH.4 only)
000  015
016  255
000  031
032  063
064  095
096  114
115  127
128  159
160  191
192  223
224  255
000  255
6
RGB Mode
7
Dimmer
Channel Function
1
2
3
Red
Green
Blue
Channel Function
1
2
3
4
Value
000  255
000  255
000  255
000  015
016  255
Red
Green
Blue
Dimmer
Value
Percent/Setting
0~100%
0~100%
0~100%
No function
Color Macros
Speed (slow to fast)
(when CH.6 is between 032-223)
No function
0-30Hz
No function
Pulse effect 0%-100%
Pulse effect 100%-0%
Pulse effect 100%-0%-100%
Chase program
Auto fade transition
Auto snap transition (3 colors)
Auto snap transition (7 colors)
Sound active mode
0~100%
Percent/Setting
000  255 0~100%
000  255 0~100%
000  255 0~100%
Value
000  255
000  255
000  255
000  255
Page 8 of 12
Percent/Setting
0~100%
0~100%
0~100%
0~100%
COLORband PiX™ Mini QRG
6-CH
Channel Function
1
2
3
4
5
6
Red
Green
Blue
Red
Green
Blue
Value
000  255
000  255
000  255
000  255
000  255
000  255
Percent/Setting
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
Section
1
2
\
9-CH
Channel Function
1
2
3
4
5
6
7
8
9
Red
Green
Blue
Red
Green
Blue
Red
Green
Blue
Value
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
Page 9 of 12
Percent/Setting
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
Section
1
2
3
COLORband PiX™ Mini QRG
18-CH
Channel Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Red
Green
Blue
Red
Green
Blue
Red
Green
Blue
Red
Green
Blue
Red
Green
Blue
Red
Green
Blue
Value
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
000  255
Page 10 of 12
Percent/Setting
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
0~100%
Section
1
2
3
4
5
6
COLORband PiX™ Mini QRG
Mounting
Before mounting this product, read the Safety Notes at the beginning of this
guide and in the product’s User Manual. The mounting instructions are
provided in the Setup chapter of the User Manual.
Product
Mounting
Diagram
L Bracket
Bracket Adjustment Knob
Mounting Bracket
Page 11 of 12
COLORband PiX™ Mini QRG
Contact Us
World Headquarters
United Kingdom and Ireland
CHAUVET®
CHAUVET® Europe Ltd.
General Information
Address:
Voice:
Fax:
Toll free:
5200 NW 108th Avenue
Sunrise, FL 33351
(954) 929-1115
(954) 929-5560
(800) 762-1084
Technical Support
Voice:
Fax:
Email:
(954) 929-1115 (Press 4)
(954) 756-8015
[email protected]
World Wide Web
General Information
Address:
Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice:
+44 (0)1773 511115
Fax:
+44 (0)1773 511110
Technical Support
Email:
[email protected]
World Wide Web
www.chauvetlighting.com
www.chauvetlighting.co.uk
Outside the U.S., United Kingdom, or Ireland, contact your distributor of
record. Follow their instructions to request support or to return a product.
Visit our website for contact details.
COLORband PiX™ Mini QRG – Rev. 05
© Copyright 2012 CHAUVET®
All rights reserved.
Printed in the P. R. C.
Page 12 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement