Aspen | Vented Gas Fireplace | Owner`s manual | Aspen Vented Gas Fireplace Owner`s manual

MODEL CR/DX MANUAL
VENT-FREE OR VENTED GAS LOGS
CR/DX 18”, 24”, 30” & CR 24” MOUNTAINEER ,
CR24 ASPEN LOG SETS
FOR NATURAL OR LIQUID PETROLEUM (L.P.)
WITH OPTIONAL HEAT SHIELD MODEL (19HS)
WARNING: If the following information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury, or loss of life.
-DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN
THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
-WHAT TO DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use any phone in your building.
* Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
* If you cannot reach the gas supplier, call the fire department.
-Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
-This appliance is intended for supplemental heating.
This is an unvented and vented gas-fired heater. It uses air (oxygen) from the room in which it is installed.
Provisions for adequate Combustion and Ventilation Air must be provided. Refer to Section V, page 34.
This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home, where
not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not
convertible for use with other gases.
WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not permitted.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
New Buck Corporation
P.O. Box 69
200 Ethan Allen Drive
Spruce Pine, NC 28777
www.buckstove.com
Revised January 2013
TABLE OF CONTENTS
SECTION I: Safety Information ..................................................................................................3
SECTION II: Residential Installation-Unvented Gas Logs .......................................................6
Clearances .....................................................................................................................................7
Gas Connection .............................................................................................................................8
Preparing Log Kit..........................................................................................................................8
Log Placement Diagrams ........................................................................................................ 9-16
Gas Pressure Check.....................................................................................................................17
Lighting Instructions-Millivolt Valve (SIT) ...............................................................................18
Lighting Instructions-Modulating Valve (SIT) ...........................................................................22
Lighting Instructions-Manual Valve (SIT) .................................................................................26
Flame Check................................................................................................................................30
Heat Output .................................................................................................................................30
SECTION III: Installation-Heat Shield.......................................................................................31
Wiring Diagram...........................................................................................................................33
SECTION IV: Installation-After Market Mobile Home .............................................................35
SECTION V: Producing Adequate Combustion and Ventilation Air.........................................35
Air For Combustion And Ventilation Inside Building................................................................38
Air For Combustion And Ventilation Outdoors..........................................................................39
SECTION VI: Vented Logs ........................................................................................................40
Important Safeguards ..................................................................................................................42
Cleaning ......................................................................................................................................42
Troubleshooting ..........................................................................................................................43
Servicing and Replacement Parts................................................................................................48
Warranty......................................................................................................................................52
Owner Registration Card..............................................................................................Back Cover
SECTION I
SAFETY INFORMATION
WARNINGS
IMPORTANT:
READ THIS OWNER'S MANUAL CAREFULLY AND
COMPLETELY BEFORE TRYING TO ASSEMBLE, OPERATE, OR SERVICE THE
APPLIANCE. IMPROPER USE OF THESE LOGS CAN CAUSE SERIOUS INJURY
OR DEATH FROM BURNS, FIRE, EXPLOSION, AND CARBON MONOXIDE
POISONING.
Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, and/or
nausea. If you have these signs, the heater may not be working properly. Get fresh air
at once! Turn off gas. Have burner serviced. Some people (such as pregnant women, persons with heart or lung disease, persons with anemia, those under the
influence of alcohol, and those at
high altitudes)
are
more affected by
carbon
monoxide
than
others.
Make
certain
you understand and read all
Warnings. Keep this manual for reference. It is your guide to safe and proper operation of
these logs.
1. Install log set only in a solid-fuel-burning masonry fireplace or U.L. listed prefabricated fireplace constructed of non-combustible materials.
2. The installation must conform with local codes or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA 54.
3. This appliance may be installed in an After Market* Manufactured (Mobile) Home,
where not prohibited by state or local codes.
(* After Market: Completion of sale, not for purpose of resale from the manufacturer.)
NOTE: This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases.
NOTE: See Section IV for Mobile Home Installation and Producing adequate Combustion and
Ventilation Air.
IMPORTANT: VENT-FREE HEATERS ADD MOISTURE TO THE AIR. ALTHOUGH
THIS IS BENEFICIAL, INSTALLING HEATER IN ROOMS WITHOUT ADEQUATE
VENTILATION MAY CAUSE MILDEW TO FORM FROM TOO MUCH MOISTURE.
4. Never install the log set:
-in a recreational vehicle.
-where curtains, furniture, clothing, or other flammable objects are less than 42" from the
front of the heater.
-in high traffic areas or in windy areas.
NOTE: These log sets comply with both the ANSI Z21.11.2b-2010 "Unvented Room
Heater" and ANSI Z21.60b-2004. CSA 2.26-2004 Decorative Appliance For "Solid Fuel
Burning Fireplace".
“WARNING: ANY CHANGE TO THIS HEATER OR ITS CONTROLS CAN BE
DANGEROUS.”
Page 3
5. Two models are available. One specific model for propane (LP) and one for natural gas.
Use the correct gas type for your home. This unit is not field convertible.
6. If these gas logs are for use with propane gas, do not place propane supply tank(s) inside
any structure. Locate propane supply tank(s) outdoors.
7. If you smell gas:
-Shut off gas supply.
-Do not try to light any appliance.
-Do not touch any electrical switch; do not use any phone in your building.
-Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
-If you cannot reach your gas supplier, call the fire department.
8. When operated for the first time, the logs may emit a "paper burning" smell. This smell
will gradually diminish and will be totally eliminated after the first few hours of
operation. Run the gas logs with the flue damper open during this time. Do not use the
blower at this time.
9. "This heater shall not be installed in unusually tight construction unless provisions are
provided for adequate combustion and ventilation air. "See Section V - “Producing
Adequate Combustion and Ventilation Air”, page 34.
10. Surface of gas logs becomes very hot when operating. Keep children and adults away
from hot surface. Gas logs will remain hot for some time after shutdown. Allow surface
to cool before touching.
11. Never place any objects on these gas logs.
12. These gas logs MUST NOT BE USED with glass doors in the closed position.
13. If equipped, fresh air damper must be closed.
14. Keep appliance area clean and free from combustible materials, gasoline, and other
flammable vapors and liquids. Keep burner and control compartment
clean. See installation and operating instructions accompanying heater.
15. If burner shuts off, do not relight until you provide fresh outside air. If burner keeps
shutting off, have unit serviced.
16. An unvented room heater having input rating of more than 10,000 BTU per hour
shall not be installed in a bedroom or bathroom.
17. Maintain clearance around air openings.
WARNING: This appliance is equipped for (natural or propane) gas. Field conversion
is not permitted.
Page 4
18. Do not use the appliance if any part has been under water. Immediately call a qualified
service technician to inspect the appliance and to replace any part of the control system and
any gas control which has been under water.
19. Turn off the gas logs and let cool before servicing.
20. The logs are made of light weight refractory. Hold both ends of the logs when removing or
replacing.
21. Make sure any safety screen or guard (if any) that was removed for servicing is in place
before operating gas logs.
22. Strong drafts, such as a ceiling fan placed directly in front of the fireplace, may create
sooting. Sooting may discolor walls.
23. Installation and repair should be done by a qualified service person. The heater and the gas
logs should be inspected before use and at least annually by a professional service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding
materials, etc. It is important that the control compartment, burners, and circulating air
passageways of these gas logs be kept clean and clear.
24. Do not use these gas logs for burning trash or cooking. Never place matches, paper,
garbage or any other material on top of logs or into the flames.
25. Do not install or operate these gas logs in areas where impurities in the air exist (such as
tobacco smoke and heavy cooking grease). Particles from impurities may discolor walls.
26. The appliance and its individual shutoff valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of 1/2
psi (3.5 kPa).
27. The appliance must be isolated from the gas piping system by closing its individual manual
shut off valve during any pressure testing of the gas supply piping system at test pressures
equal to or less than 1/2 PSIG.
28. Any outside air ducts and/or ash dumps in the fireplace shall be permanently closed at
time of appliance installation.
29. Due to high temperatures, the appliance should be located out of traffic and away from
furniture and draperies.
31. Do not place clothing or other flammable material on or near the appliance.
WARNING: “State or local codes may only allow operation of this appliance in a vented
configuration. Check your state on local codes”.
Page 5
SECTION II
RESIDENTIAL INSTALLATION OF GAS LOGS
FIREPLACE PREPARATION
The fireplace needs to be prepared before installing the gas logs.
A. Turn off the gas supply to the fireplace.
B. Any outside air ducts on the fireplace shall be permanently closed at the time of the appliance
installation.
“WARNING: BEFORE INSTALLING IN A SOLID FUEL BURNING FIREPLACE, THE
CHIMNEY FLUE AND FIREBOX MUST BE CLEANED OF SOOT, CREOSOTE, ASHES
AND LOOSE PAINT BY A QUALIFIED CHIMNEY CLEANER.”
“WARNING: DO NOT ALLOW FANS TO BLOW DIRECTLY INTO THE FIREPLACE.
AVOID ANY DRAFTS THAT ALTER BURNER FLAME PATTERN.”
LOCATION
Centrally locate the gas logs in the fireplace. Place them deep enough into the fireplace to
accomplish adequate draft (if use as a vented gas log set is planned). Ensure that the front of the logs
sit inside the front edge of the fireplace.
For your convenience, we have furnished two holes in the rear bottom bar of the burner base to fasten
it to the floor if you deem it necessary.
NOTE: IF THE EXISTING FIREPLACE IS EQUIPPED WITH A SCREEN IT MUST BE IN
PLACE WHEN THE APPLIANCE IS OPERATING. THE SCREEN SHALL HAVE
ADEQUATE OPENING(S) FOR INTRODUCTION OF AIR FOR COMBUSTION AND
VENTILATION.
NOTE: MAINTAIN PROPER CLEARANCE FOR PURPOSE OF SERVICING, PROPER
INSTALLATION, AND OPERATION.
ANGLE MANTEL
FLAT MANTEL
16"
17"
13"
MAX. OF 2 1/2"
14"
10"
4" *
FIGURE 1
Page 6
Mantel Minimum Clearances for a
21" listed Zero Clearance Firebox or
a Masonry Fireplace.
* WARNING: Canopy model number
MAPSFPC must be used at all times unless a
10-inch mantel is installed at 36-inches
above the fireplace opening. (Can be
obtained from your local dealer or
purchased from the factory.)
“WARNING: THIS APPLIANCE IS FOR INSTALLATION ONLY IN A SOLID FUEL
BURNING MASONRY OR UL127 FACTORY BUILT FIREPLACE OR IN A LISTED
VENTLESS FIREBOX ENCLOSURE.
IT HAS BEEN DESIGN CERTIFIED FOR THESE INSTALLATIONS. EXCEPTION:
DO NOT INSTALL THIS APPLIANCE IN A FACTORY BUILT FIREPLACE THAT
INCLUDES INSTRUCTIONS STATING IT HAS NOT BEEN TESTED OR SHOULD
NOT BE USED WITH UNVENTED GAS LOGS.”
INSTALLATION AND CLEARANCES
To ensure a safe installation into an existing solid fuel burning fireplace, the following
instructions must be carefully followed.
NOTE: Gas control knobs are located on right side facing unit.
1) Side wall Clearances:
Clearance from the right and left side of the fireplace opening to any adjacent
combustible wall should not be less than 8".
2) Ceiling Clearances:
The ceiling height should not be less than 42" from the top of the fireplace opening.
3) Mantel Clearances:
For clearances from top of heater to mantel or mantel supports see Figure 1.
4) Front Clearances:
No objects should be placed within 24" from the front of the fireplace opening.
.
MINIMUM FIREPLACE DIMENSIONS FOR LOG SETS MANUFACTURED BY NEW
BUCK CORPORATION FOR SOLID FUEL BURNING FIREPLACE OR MASONRY
FIREPLACE AND PREFAB OR MANUFACTURED FIREPLACES.
NOTE: When using logsets with the Model 19HS heat shield see page 30 for clearances.
MODEL
HEIGHT OF
WIDTH OF
WIDTH AT
DEPTH OF
(CR, DX)
OPENING
OPENING
REAR
FIREPLACE
AT FRONT
18
17"
25"
18"
14"
24
17"
30"
24"
14"
30
17"
36"
26"
14"
WARNING:
ANY CHANGE TO THIS HEATER OR ITS CONTROLS CAN BE
DANGEROUS.
WARNING:
“Cutting any sheet metal parts of the solid-fuel burning fireplace or
listed ventless firebox enclosure in which the unvented fireplace insert (log set) is to be
installed is prohibited.”
NOTE: “Smoke shelves, shields and baffles may be removed if attached by mechanical
fasteners.”
NOTE: “Refractory, glass doors, screen rails, screen mesh and solid-fuel log grates (if
applicable) can be removed from the fireplace before installing the unvented fireplace
insert.”
NOTE: Glass doors must be in the open position, and screens must be in place in the
closed position when the appliance is in use.
Page 7
GAS CONNECTION
Check gas type. Use only the type of gas indicated on the valve rating plate. If the type of gas
listed on the plate is not your type of gas supply, DO NOT INSTALL. Contact your dealer for
proper model.
Always use an external regulator for all LP heaters to reduce the supply tank pressure to a
maximum of 13" W.C. This is in addition to the regulator furnished with the heater.
Warning: Connection directly to an unregulated LP tank can cause an explosion.
The normal gas connection is 3/8" N.P.T. made at the right side facing the log set. If a left
side connection is desired, the connecting pipe may be routed under the rear of the burner
base to terminate at the right hand side for connection to the inlet of the valve.
NOTE: The connecting pipe must be internally tinned copper tubing for use with natural gas.
Test for leaks using a solution of soap and water after completing the connection. DO NOT
USE OPEN FLAME.
PREPARING LOG KIT
Open the cartons containing the Burner Base and the logs. Inside one of the cartons you will
find the Burner Base. The logs are boxed separately.
WARNING: POSITIONING OF LOGS IS VERY CRITICAL (See Figure 2).
LOG PLACEMENT FOR 18 (FIBER) LOG SETS:
1) Place rear log (flat faced)#1 on rear log support. The log has alignment notches on each
corner.
2) Place ember strip (wrapped in cardboard box)#2 on front bottom andirons. Center from
side to side.
3) Next place middle log (with ember burn out)#3 over front burner tube. The two ends are
notched out on bottom to ensure proper fitting over ends of burner.
4) Right top log is a “y” shaped log #4. The round stem lays in the notched out space on the
right top corner of rear log. There is a pin on the middle log, and a hole on the flattened end
of the top left log. Place hole over pin.
5) Place one end of the left top log #5 in notch of left corner on rear log and the other end of
the left top log in notch on top middle log.
Solid fuels shall not be burned in the same fireplace where an unvented room heater has
been installed.
NOTE: The following label has been provided with this appliance and must be read and
then attached to the floor of the fireplace or firebox area beneath the appliance. The label
is a peel and stick label. Make sure the area is cleaned before attaching the label to it.
“WARNING: This solid-fuel burning fireplace or listed ventless enclosure has been
converted for use with an unvented fireplace insert only. A solid-fuel burning fireplace
cannot be used for burning wood or solid fuels unless all original parts have been
replaced, and the fireplace re-approved by the authority having jurisdiction. A ventless
firebox enclosure cannot be used with an unvented gas log unless all original parts have
been replaced, and the ventless firebox enclosure re-approved by the authority having
jurisdiction.”
Page 8
WARNING:
Failure to position the parts in accordance with these diagrams or
failure to use only parts specifically approved with this heater may result in property
damage or personal injury.
5
18 (Fiber)
4
1
3
2
Figure 2
LOG PLACEMENT FOR MODEL 24 (FIBER) LOG SETS (See Figure 3.)
1) Front log #1 has two notches in bottom of log. Place the log so the notches are over the 3/4" x
3/4" square bar of each leg of burner base.
2) Place middle log #2 over front burner tube. There are alignment notches in each corner.
3) Rear log #3 has notches in both rear corners. Place in the rear log holders at the rear of the
burner base.
4) Place the big end of right top log #4 over pin in the middle of rear logs. The smaller end also
has a hole that places over the pin in the middle log.
5) Left top log #5 sits in notches on rear and middle logs.
5
4
2
3
24 (Fiber)
1
Figure 3
Page 9
NEWER LOG SETS
MAY HAVE A TWO
(2) PIECE LOG.
5
30 (Fiber)
4
3
2
1
NEWER LOG SETS
MAY HAVE A TWO
(2) PIECE LOG.
Retrofit Grate
Figure 4
LOG PLACEMENT FOR MODEL 30 (FIBER) LOG SETS:
Repeat steps for Model 24 (Fiber) Log Placement except before placing #1 front log into
position, place the retrofit grate that comes with Model 30 logs over the two 3/4" x 3/4" square
bar on legs of burner base.
WARNING:
Failure to position the parts in accordance with these diagrams or
failure to use only parts specifically approved with this heater may result in property
damage or personal injury.
Page 10
CR18 LOG SET
(WITH DX18MV LOG BASE)
Open the cartons containing the Burner Base and the logs. Inside one of the cartons you will find the Burner Base. The logs are
boxed separately.
CR18: 1) Rear Log, 2) Ember strip, 3) Front log, 4) Top Log.
WARNING:
POSITIONING OF LOGS IS VERY CRITICAL. (See Figure 5.)
LOG PLACEMENT FOR CR18 LOG SETS:
1) Place rear log #1 on rear log support. The log has two alignment notches on back.
2) Place ember strip #2 on front bottom andirons. Center from side to side.
3) Next place front log #3 between rear and front burner tubes on the log supports for proper alignment.
4) Left top log #4 has two holes provided to fit over the pins in the front log to insure proper fit.
4
Figure 5
1
3
2
WARNING:
Failure to position the
parts in accordance with these diagrams
or failure to use only parts specifically
approved with this heater may result in
property damage or personal injury.
Page 11
CR24 LOG SET
(WITH DOUBLE BURNER DX24MV LOG BASE)
Open the cartons containing the Burner Base and the logs. Inside one of the cartons you will find the
Burner Base. The logs are boxed separately.
CR24: 1) Rear Log, 2) Middle Log, 3) Front Log, 4) Right Top Log, 5) Left Top Log, 6) *Extreme Front
log used only with C24DTB Tri Burner Base.
WARNING:
POSITIONING OF LOGS IS VERY CRITICAL. (See Figure 6.)
LOG PLACEMENT FOR CR24 LOG SETS:
1) Align the two holes on the bottom of the rear log #1 over rear base legs and slide down to the supports.
2) Place the middle log #2 on the support between the front and rear burner sliding log flush to the back of
the support. Center from side to side.
3) Next place front log #3 behind the front of the andirons, resting on top of its legs
4) Right top log #4 has two holes provided to fit over the pins in the right side of the middle log to ensure
proper fit.
5) Left top log #5 has two holes provided to fit over the pins in the left side of the middle log to ensure
proper fit.
5
4
1
Figure 6
2
3
* NOTE: Discard log #6 on
double burner log base.
WARNING:
6
Failure to position the
parts in accordance with these diagrams
or failure to use only parts specifically
approved with this heater may result in
property damage or personal injury.
Page 12
CR24 MOUNTAINEER LOG SET
(WITH DOUBLE BURNER DX24MV LOG BASE)
WARNING:
POSITIONING OF LOGS IS VERY CRITICAL. (See Figures 6a & 6b)
LOG PLACEMENT FOR CR24 MOUNTAINEER LOG SETS:
1) Align the hole on back of the rear log (#1) with the right rear leg and slide down to the supports. Left side
of rear log (#1) will simply rest on left support.
2) Place the middle log (#2) on the support between the front and rear burner sliding log flush to the back of
the support. Center from side to side.
3) Next place front log (#3) behind the front of the andirons, resting on top of its legs. Small notch on the
right of the log (#3) should line up with the right andiron support.
4) Left top log (#4) has two holes provided to fit over the pins in the left side of the rear log (#1) and the left
side middle log (#2) to ensure proper fit.
5) Center top log (#5) has a hole to fit over the pin in the center of the rear log (#1). The other end of the
center top log (#5) comes to rest on the flattened area in the center of the middle log (#2).
6) Right top log (#6) has a hole to fit over the pin on the right side of the middle log (#2). The other end of
the right top log (#6) comes to rest on the top right of the front log (#3) pointing towards the andiron.
5
4
6
1
Completed Log Placement (Front View)
2
3
Completed Log Placement (Left Angle View)
Figure 6b.
Figure 6a.
Page 13
CR30 LOG SET
(WITH DOUBLE BURNER DX24MV LOG BASE)
Open the cartons containing the Burner Base and the Log Set. Inside one of the cartons you will find the
Burner Base. The Log Set is boxed separately.
CR30: 1) Rear Log. 1) Middle Log. 2) Front Logs. 3A, 3B) Right Top Log. 4) Left Top Log 5).
There are (2) two brass round knobs to enhance your Log Set. The knobs are threaded in the bottom.
Position the knobs over the threaded studs of the front top andirons and tighten.
Remove the Front Log(s) Base Plate. The Base Plate sets just behind the front andirons with the two (2)
locator studs facing upward. Insure that the Base Plate is completely seated on to the log base. See diagram bellow.
WARNING: POSITIONING OF THE LOGS IS VERY CRITICAL.
LOG PLACEMENT FOR CR30 LOG SET (SPLIT FRONT LOG) :
1) Align the two notches on the bottom rear of the Rear Log #1 over the rear log supports mounted to
the rear legs of the burner base.
2) Place the Middle Log #2 on the support between the front and rear burner sliding the log flush to the
back of the support. Center the log from side to side.
3) Next place Front Log #3A behind the front of the andirons (left side), resting on the locator stud,
which is located on the top of the front log(s) Base Plate. Repeat this step with Front Log #3B (right
side). The logs should meet and over lap in the center of the log base.
4) The Right Top Log #4 has (2) two holes provided to insure proper placement. Align the holes in the
log with the pins on the right hand side of the Middle Log #2, place the log gentility on to the pins.
5) To place the Left Top Log #5 use the (2) holes provided and the pins on the left side of the logs and
repeat the steps in #4.
FRONT LOG(S)
BASE PLATE
Page 14
LOG PLACEMENT FOR CR30 LOG SET (SPLIT FRONT LOG) :
#1
#4
#2
#5
#3B
#3A
WARNING: Failure to position the parts
in accordance with this diagram or failure
to use only parts specifically approved
with this heater may result in property
damage or personal injury.
Page 15
CR24 ASPEN LOG SET
(WITH DOUBLE BURNER DX24MV LOG BASE)
WARNING:
POSITIONING OF LOGS IS VERY CRITICAL.
LOG PLACEMENT FOR CR24 ASPEN LOG SET:
1) Align the two holes on the bottom of the rear log #1 over rear base legs and slide down to the supports.
2) Place the middle log (#2) on the support between the front and rear burner sliding log flush to the back of
the support. Center from side to side.
3) Next place front log (#3) behind the front of the andirons, resting on top of its legs. Small notch on the
right of the log (#3) should line up with the right andiron support.
4) Left top log (#4) has two holes provided to fit over the pins in the left side of the middle log (#1) and the
left side front log (#2) to ensure proper fit.
5) Right top log (#5) has a hole to fit over the pins on the right side of the rear log (#1) and the right side
middle log (#2) to ensure proper fit.
1
5
4
2
Completed Log Placement (Front View)
3
Completed Log Placement (Left Angle View)
Page 16
GAS PRESSURE CHECK
Check the inlet pressure to the burner to ensure that it is as shown in the table below.
NOTE: The pressure check point is located on right side of valve facing the burner.
The appliance and its appliance main gas valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressure in excess of 1/2 psi
(3.5 kPa).
The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or
less than 1/2 psi (3.5 kPa).
MODEL
18 (CR, DX)
Gas
Natural
Propane (LP)
Maximum Heat Input 30,000
30,000
Minimum Heat Input
23,000
23,000
Gas Inlet Pressure:
Maximum
10.5 ins. W.C. 13.0 ins. W.C.
Minimum
4.5 ins. W.C. 10.5 ins. W.C.
Manifold Pressure
3.5 ins. W.C. 10.0 ins. W.C.
24 / 30 (CR, DX)
Natural
Propane(LP)
40,000
40,000
29,000
29,000
10.5 ins.W.C. 13.0 ins. W.C.
4.5 ins. W.C. 10.5 ins. W.C.
3.5 ins. W.C. 10.0 ins. W.C.
NOTE: On initial installation it may be required to bleed out air in the gas lines. Do this by
holding the control knob and turning the knob to the pilot position for about 30 seconds.
The pressure should be checked with the heater burning and the control set on high. After
measuring the pressure, close pressure tap screw, ensuring there are no leaks. Regulator pressure
check screw located above “OFF/ PILOT/ON” knob at right upper corner of valve.
WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is
not permitted.
Page 17
OPERATING INSTRUCTIONS
Before operating this appliance, proceed through the following checklist.
1. Read and understand these instructions before operating this appliance.
2. Check that there are no gas leaks. If you smell gas do not attempt to light this appliance.
3. Verify that log placement is correct.
LIGHTING INSTRUCTIONS
SIT-MILLIVOLT VALVE
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury, or loss of life.
A. This appliance has a pilot which must be lighted by hand. When lighting the pilot follow
these instructions exactly. If piezo fails, then light the pilot using matches. Refer to the
match lighting instructions.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to
the floor because some gas is heavier than air and will settle to the floor.
WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electric switch; do not use any phone in your building.
* Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
* If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas knob. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it. Call a qualified service technician. Force or
attempted repair may result in a fire or explosion.”
D. Do not use this appliance if any or part of it has been under water. Immediately call a
qualified service technician to inspect the appliance and to replace any part of the control system
and any gas control which has been under water.”
Page 18
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information on the reverse side of this label (page 17).
2. Make sure manual shutoff valve is fully closed. If equipped with thermostat, set to the
lowest setting.
3. Turn off all electrical power to the appliance.
4. Push in gas control knobslightly and turn clockwise
to the full “OFF” position.
REMOTE CONTROL OR
WALL THERMOSTAT
NOTE:Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force.
5. Wait (5) five minutes to clear out any gas. Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” in the safety information on the reverse side of this label.
If you don’t smell gas, go to the next step.
6. Find Pilot: follow metal tube from gas control. The pilot is located behind the rear burner
tube and in front of the rear log. Fully open the manual shutoff valve.
7. Press in and turn knob on gas control counterclockwise
to “PILOT” and continue
pressing in the knob for (15) fifteen seconds.
8. With control knob pressed in push down (in) and release the igniter button (igniter button is
located on the left hand side of the front of the appliance). This will light the pilot. If
needed, keep repeating this step until pilot lights.
9. Keep control knob pressed in for (1) one minute after lighting pilot. After (1) minute,
release the control knob and it will pop back up. Pilot should remain lit. If pilot goes out,
repeat steps 1 through 9.
 If the knob does not pop up when released, stop and immediately call your service
technician or gas supplier.
Page 19
* If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call
your service technician or gas supplier.
10. Turn control knob counterclockwise
to “ON”.
11. If using unit without wall thermostat place Auto/Off/Manual switch into the manual
position. If using wall thermostat place Auto Off Manual Switch into the auto position and
place thermostat to a setting higher than the room temperature.
12. “Turn on all electrical power to the appliance.”
13. Your heater is equipped with a HI & LO control. Turn clockwise for Low and
counterclockwise for High.
14. Set thermostat to desired setting.
CAUTION
DO NOT TRY TO ADJUST HEATING LEVELS BY USING THE MANUAL SHUTOFF
VALVE.
TO TURN OFF GAS TO
APPLIANCE
SHUTTING OFF UNIT
1. “If equipped with thermostat set to lowest setting.”
2. Turn control knob clockwise
to the full “OFF”.
3. Turn off all electric power to the appliance if service is to be performed.
SHUTTING OFF BURNER ONLY (Pilot stays lit.)
1. Turn control knob clockwise
to the “PILOT” position.
CAUTION:
Hot while in operation. Do Not Touch. Keep children, clothing, furniture,
gasoline, and other liquids having flammable vapors away.
CAUTION: DO NOT TRY TO ADJUST HEATING LEVELS BY USING THE
MANUAL SHUTOFF VALVE.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, personal injury, or loss of life. Refer to owner’s information manual
provided with this appliance. Installation and service must be performed by a qualified
installer, service agency, or the gas supplier.
IMPORTANT:
Always operate the appliance at the completely “ON” or the completely
“OFF” positions. Never use the heater at a setting between these positions as this can result in
improper combustion and excessive carbon monoxide emissions.
Page 20
MANUAL LIGHTING PROCEDURE
1. If the pilot cannot be ignited with the piezo, it can be manually lit with the use of a paper
match and lighter rod.
2. Place the match in the holder and light. With the left hand, depress the control knob
counterclockwise

to “PILOT”. Hold in.
3. Take rod and light match and ignite pilot. The pilot is located behind the right hand side
of the front log.
4. Continue to hold the control knob for an additional 1 (one) minute to ensure the pilot is lit.
Page 21
LIGHTING INSTRUCTION
MODULATING VALVE (SIT)
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.”
A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow
these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to
the floor because gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:



Do not try to light any appliance.
Do not touch any electric switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
 If you cannot reach your gas supplier, call the fire department.”
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob
will not push in or turn by hand, don’t try to repair it’ call a qualified service technician.
Force or attempted repair may result in a fire or explosion.”
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and
any gas control which has been under water.”
Page 22
LIGHTING INSTRUCTION
1. STOP! Read the safety information on preceding page 21.
2. Set the thermostat to lowest setting.
3. Make sure manual shutoff valve is fully closed.
4. Turn off all electrical power to the appliance.
5. Open access panel door, located at the lower front center of the appliance.
6. Turn control knob clockwise
to the full “OFF” position.
7. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” on preceding page in the Safety Information. If you
don’t smell gas, go to the next step.
8. 7. Find Pilot: follow metal tube from gas control. The pilot is located behind the
rear
burner tube and in front of the rear log. Fully open the manual shutoff valve
9. Press in and turn gas control knob counterclockwise
to the “PILOT” position continue pressing in control knob for fifteen (15) seconds.
10. With control knob pressed in, push down (in) and release the igniter button (igniter button
is located on the left hand side of the gas control valve) . This will light pilot. If needed,
keep repeating this step until pilot lights.
11. Keep control knob pressed in for one (1) minute after lighting pilot. After one (1) minute,
release control knob and it will pop back up. Pilot should remain lit. If pilot goes out, repeat
steps 1 through 9.
 If the knob does not pop up when released, stop and immediately call your service technician or gas supplier.
 “If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call
your services technician or gas supplier.”
Page 23
12. Turn gas control knob counterclockwise
to “ON” position. Continue to turn the
gas control knob counterclockwise
to your desired setting.
13. Close access panel door.
14. Turn on all electrical power to the appliance.
15. Set thermostat to desired setting.
CAUTION
DO NOT TRY TO ADJUST HEATING LEVELS BY USING THE MANUAL SHUTOFF
VALVE.
TO TURN OFF GAS TO APPLIANCE
SHUTTING OFF UNIT
1. Open access panel door.
2. Set thermostat to lowest setting.
3. Turn gas control knob clockwise
to the full “OFF” position.
4. Turn off all electric power to the appliance if service is to be performed.
5. Close access panel door.
SHUTTING OFF BURNER ONLY (pilot stays lit)
1. Turn control knob clockwise
to the “PILOT” position.
CAUTION:
Hot while in operation. Do Not Touch. Keep children, clothing, furniture,
gasoline, and other liquids having flammable vapors away.
CAUTION: DO NOT TRY TO ADJUST HEATING LEVELS BY USING THE
MANUAL SHUTOFF VALVE.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, personal injury, or loss of life. Refer to owner’s information manual
provided with this appliance. Installation and service must be performed by a qualified
installer, service agency, or the gas supplier.
IMPORTANT:
Always operate the appliance at the completely “ON” or the completely
“OFF” positions. Never use the heater at a setting between these positions as this can result in
improper combustion and excessive carbon monoxide emissions.
Page 24
THERMOSTAT CONTROL OPERATION
The thermostat control used on this heater differs from standard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. The thermostat adjusts the amount of gas flow to the burner. This increases or decreases the burner flame height. At times the room may exceed the set temperature. If so, the
burner will shut off. The burner will cycle back on when the room temperature drops below the
set temperature. The control knob can be set to any level between LOW and HIGH.
NOTE: The thermostat sensing bulb measures the temperature of air near the heater cabinet.
This may not always agree with room temperature (depending on housing construction, installation location, room size, open air temperatures, etc.). Frequent use of your heater will let you
determine your own comfort levels.
MANUAL LIGHTING PROCEDURE
1. If the pilot cannot be ignited with the piezo, it can be manually lit with the use of a paper
match and lighter rod.
2. Place the match in the holder and light. With the left hand, depress the control knob counterclockwise
to “PILOT”. Hold in.
3. Take rod and light match and ignite PILOT. The PILOT is located behind the right hand
side of the front log.
4. Continue to hold the control knob for an additional one (1) minute to ensure the pilot is lit.
Page 25
LIGHTING INSTRUCTION
MANUAL VALVE (SIT)
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.
A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow
these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to
the floor because gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:



Do not try to light any appliance.
Do not touch any electric switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
 If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob
will not push in or turn by hand, don’t try to repair it, call a qualified technician. Force or
attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and
any gas control which has been under water.
Page 26
LIGHTING INSTRUCTION
1. STOP! Read the safety information on preceding page 25.
2. Set the thermostat to lowest setting.
3. Make sure manual shutoff valve is fully closed.
4. Turn off all electrical power to the appliance.
5. Open access panel door, located at the lower front center of the appliance.
6. Turn control knob clockwise
to the full “OFF” position.
7. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If
you smell gas, STOP! Follow “B” on preceding page in the Safety Information. If you
don’t smell gas, go to the next step.
8. 7. Find Pilot: follow metal tube from gas control. The pilot is located behind the
rear
burner tube and in front of the rear log. Fully open the manual shutoff valve
9. Press in and turn gas control knob counterclockwise
to the “PILOT” position continue pressing in control knob for fifteen (15) seconds.
10. With control knob pressed in, push down (in) and release the igniter button (igniter button
is located on the left hand side of the gas control valve) . This will light pilot. If needed,
keep repeating this step until pilot lights.
11. Keep control knob pressed in for one (1) minute after lighting pilot. After one (1) minute,
release control knob and it will pop back up. Pilot should remain lit. If pilot goes out, repeat
steps 1 through 9.
 If the knob does not pop up when released, stop and immediately call your service technician or gas supplier.
 “If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call
your services technician or gas supplier.”
Page 27
12. Turn gas control knob counterclockwise
to “ON” position. Continue to turn the
gas control knob counterclockwise
to your desired setting.
13. Close access panel door.
14. Turn on all electrical power to the appliance.
15. Set thermostat to desired setting.
CAUTION
DO NOT TRY TO ADJUST HEATING LEVELS BY USING THE MANUAL SHUTOFF
VALVE.
TO TURN OFF GAS TO APPLIANCE
SHUTTING OFF UNIT
1. Open access panel door.
2. Set thermostat to lowest setting.
3. Turn gas control knob clockwise
to the full “OFF” position.
4. Turn off all electric power to the appliance if service is to be performed.
5. Close access panel door.
SHUTTING OFF BURNER ONLY (pilot stays lit)
1. Turn control knob clockwise
to the “PILOT” position.
CAUTION:
Hot while in operation. Do Not Touch. Keep children, clothing, furniture,
gasoline, and other liquids having flammable vapors away.
CAUTION: DO NOT TRY TO ADJUST HEATING LEVELS BY USING THE
MANUAL SHUTOFF VALVE.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, personal injury, or loss of life. Refer to owner’s information manual
provided with this appliance. Installation and service must be performed by a qualified
installer, service agency, or the gas supplier.
IMPORTANT:
Always operate the appliance at the completely “ON” or the completely
“OFF” positions. Never use the heater at a setting between these positions as this can result in
improper combustion and excessive carbon monoxide emissions.
Page 28
THERMOSTAT CONTROL OPERATION
The thermostat control used on this heater is very standard. It simply turns the burner on and off
manually. The control knob can be set to any level between HI and LOW.
MANUAL LIGHTING PROCEDURE
1. If the pilot cannot be ignited with the piezo, it can be manually lit with the use of a paper
match and lighter rod.
2. Place the match in the holder and light. With the left hand, depress the control knob counterclockwise
to “PILOT”. Hold in.
3. Take rod and light match and ignite PILOT. The PILOT is located behind the right hand
side of the front log.
4. Continue to hold the control knob for an additional one (1) minute to ensure the pilot is lit.
Page 29
BURNER & PILOT FLAME CHECK
A periodic check of the flames should be made. The pilot flame should always be present
when the gas logs are in operation. See figure below.
Rear Flames: The flames at the rear or at either side of the top log should be very similar,
yellow in color, and should extend about 3" to 4" above the large rear log for natural gas logs
and about 6" for propane (LP) gas log sets.
Front Flame: The flame should be 1-1/2" to 2" high touching front of middle log producing
red glowing on this log.
PILOT
BURNERS
PROPANE
MODEL 18
MODEL 24
NATURAL
MODEL 30
CR24 ASPEN
CR24 MOUNTAINEER
WHEN USED AS A HEATING APPLIANCE
HEAT OUTPUT
The heat output into the room can be controlled by the position of the flue damper, when used
as “vented gas logs”. See Section VI - Vented Models.
The heat output is controlled by the “ON/OFF” switch or wall thermostat, not by the control
knob. The gas logs are either “ON” or “OFF”.
The gas logs may be used as non-vent gas logs only where permitted by local state and city
codes. If non-vent gas logs are not permitted, then the fireplace vent area required by
local codes must be met. In the absence of local codes, the latest edition of the National
Fuel Gas Code (ANSI Z223.1) must be met.
Page 30
SECTION III
INSTALLATION OF LOGSET WITH
(OPTIONAL) HEAT SHIELD MODEL 19HS
For installation of gas supply see “Fireplace and Gas Connection” in Section II, page 8.
NOTE: Centrally locate the Heat Shield in the fireplace and place it deep enough into the
fireplace to accomplish adequate draft (if use as a vented heater is planned). Ensure that the
Heat Shield front is inside the front edge of the fireplace, see Figure 8. Using the screws and
anchor provided, fasten the Heat Shield to the floor of the fireplace. On each side of floor
frame of Heat Shield base, there is a “go through hole”. Position the Heat Shield as
described above. Mark the hole for drilling. See Figure 8.
NOTE: When using Log Sets with optional Heat Shield the following minimums must be met:
18 - Front 25" - Rear 23" - Height 20" - Depth 19 1/2"
24 - Front 30" - Rear 29" - Height 20" - Depth 19 1/2"
30 - Front 36" - Rear 32" - Height 20" - Depth 19 1/2"
Blower Motor
Floor Frame (s)
Mantel
“Flush”
Area For Log
Base Placement
(Center)
“Go Through Holes” for fastening the 19HS
to the floor.
Fireplace
Heat Shield
Figure 8
To avoid any movement of the gas log set during operation, screw the base to the floor of the
fireplace using the screws provided. Then follow log positioning in Section II.
NOTE: For the first few hours of burning, you will have a paint and burning smell. It is
recommended to leave the fan off during this period. You may also want to raise a
window or open the doors.
Page 31
REPLACEMENT PARTS
FOR (OPTIONAL) HEAT SHIELD MODEL 19HS
Always include correct name, part number, and model number of the heater when ordering
service parts.
KEY#
PART DESCRIPTION
PART NUMBER
1.
BLOWER
Rating: .120 volts/60HZ/ .54 Amps
PE-A2-40-01.
2.
110 THERMOSTAT
PE 400132
3.
CHROME SHIELD
PO HS14
4.
POWER CORD
PE 400240
Page 32
WARNING:
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE
HAZARDS OF HIGH SURFACE TEMPERATURES AND SHOULD STAY AWAY TO
AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THESE GAS
LOGS.
WARNING:
Clothing or other flammable material should not be placed on or near this
appliance.
WIRING DIAGRAM
(For Optional Heat Shield Model 19HS)
MOTOR
THERMOSTAT
JUMPER
JUMPER
JUMPER
WHITE
GREEN
BLACK
POWER CORD
NOTE: “If any of the original wire supplied with the appliance must be replaced, it must be
replaced with a wire of at least a 105o C. temperature rating.”
NOTE: Installation and repair should be done by a qualified service person. This heater
should be inspected before use and at least annually by a qualified service person. More
frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.
It is imperative that control compartments and circulating air passageways of the heater be
kept clean.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation.
Verify proper operation after servicing.
Page 33
WARNING:
ELECTRICAL GROUNDING INSTRUCTION: THIS APPLIANCE IS
EQUIPPED WITH A THREE-PRONG
GROUNDING PLUG FOR YOUR
PROTECTION
AGAINST SHOCK
HAZARD
AND
SHOULD BE PLUGGED
DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE.
WARNING:
Do not use a blower insert, heat exchanger insert or other accessories
not approved for use with this heater.
WARNING: “The motor is permanently lubricated. Do not add
Page 34
any type of lubricant.”
SECTION IV
AFTER MARKET MOBILE HOME
INSTALLATION
THIS APPLIANCE MAY BE INSTALLED IN AN AFTERMARKET*, PERMANENTLY
LOCATED, MANUFACTURED (MOBILE) HOME, WHERE NOT PROHIBITED BY
LOCAL CODES. *After Market: Completion of sale, not for the purpose of resale from the
manufacturer.
THIS APPLIANCE IS ONLY FOR USE WITH THE TYPE OF GAS INDICATED ON
THE RATING PLATE. THIS APPLIANCE IS NOT CONVERTIBLE FOR USE WITH
OTHER GASES.
NOTE: For mobile home installation follow “Residential Installation”, Section II, page 6.
SECTION V
PRODUCING ADEQUATE COMBUSTION
AND VENTILATION AIR
The National Fuel Gas Code, ANSI Z223.1/NFPA 54 defines unusually tight construction or
unconfined space as a space whose volume is less than 50 cubic feet per 1,000 BTU per hour
(4.8m 3 per kw) of the aggregate input rating of all appliances installed in that space and an
unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 BTU per hour
(4.8m 3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms
communicating directly with the space in which the appliances are installed, through openings
not furnished with doors, are considered a part of the unconfined space.
“WARNING: IF THE AREA IN WHICH THE HEATER MAY BE OPERATED IS
SMALLER THAN THAT DEFINED AS AN UNCONFINED SPACE OR IF THE
BUILDING IS OF UNUSUALLY TIGHT CONSTRUCTION, PROVIDE ADEQUATE
COMBUSTION AND VENTILATION AIR BY ONE OF THE METHODS DESCRIBED
IN THE NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, SECTION 5.3 OR
APPLICABLE LOCAL CODES.”
Unusually tight construction is defined as construction where:
A) Walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder
with a rating of 1 perm (6 x 10-11 kg per pa-sec-m2) or less with openings gasketed or sealed;
B) Weather stripping has been added on openable windows and doors;
C) Caulking or sealants are applied to areas such as joints around window and door frames,
between sole plates and floors, between wall-ceiling joints, between wall panels, at
penetrations for plumbing, electrical, and gas lines, and at other openings.
Page 35
NOTICE
SOME AREAS IN THE UNITED STATES HAVE HIGHER REQUIREMENTS FOR
CUBIC FEET PER 1000 BTU/ HOUR INPUT. (EX. CINCINNATI, OHIO CODES
REQUIRE 70 CUBIC FEET).
CHECK YOUR LOCAL CODE BEFORE
INSTALLATION.
DETERMINING FRESH-AIR FLOW FOR
HEATER LOCATION
DETERMINE IF YOU HAVE UNUSUALLY TIGHT CONSTRUCTION OR UNCONFINED SPACE
Use this worksheet to determine if you have unusually tight construction or unconfined space.
SPACE: Includes the room in which you will install heater plus adjoining rooms with
doorless passageways or ventilation grills between the rooms.
1. Determine the volume of the space (length x width x height).
Length x Width x Height =_________cu.ft.(volume of space)
EXAMPLE: 20 ft.(Length) x 16 ft.(Width) x 8 ft.(ceiling Height)=
2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the
volume of these rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum BTU/Hr the
space can support.
_________(volume of space)/50 cu. ft. =maximum BTU/Hr the space can support)
EXAMPLE: 2560 cu. ft. (volume of space /50 cu. Ft .= 51.2 or
51200 (maximum BTU/Hr the space can support)
3. Add the BTU/Hr of all fuel burning appliances in the space.
Vent-free heater
_______________BTU/Hr
Gas water heater*
_______________BTU/Hr
Gas furnace
_______________BTU/Hr
Vented gas heater
_______________BTU/Hr
Gas fireplace logs
_______________BTU/Hr
Other gas appliances*
+ _______________BTU/Hr
Total
= _______________BTU/Hr
Page 36
Example: Gas water heater 40000 BTU/Hr
Vent-free heater + 18000 BTU/Hr
Total
= 58000 BTU/Hr
*Does not include direct-vent gas appliances. Direct-vent draws combustion air
from the outdoors and vents to the outdoors.
4. Compare the maximum BTU/Hr the space can support with the actual amount of
BTU/Hr used.
____________BTU/Hr (maximum the space can support)
____________BTU/Hr (actual amount of BTU/Hr used)
Example: 51200 BTU/Hr (maximum the space can support)
58000 BTU/Hr (actual amount of BTU/Hr used)
The space in the above example is unusually tight construction because the actual BTU/Hr
used is more than the maximum BTU/Hr the space can support. You must provide additional
fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an
unconfined space, remove door to adjoining room or add ventilation grills between rooms.
See “Air For Combustion And Ventilation Inside Building”, page 37.
B. Vent room directly to the outdoors. See “Air For Combustion And Ventilation
Outdoors”, page 38.
C. Install a lower BTU/Hr heater, if lower BTU/Hr size makes room unconfined.
If the actual BTU/Hr used is less than the maximum BTU/Hr the space can support, the
space is an unconfined space. You will need no additional fresh air ventilation.
WARNING
YOU MUST PROVIDE ADDITIONAL COMBUSTION AND VENTILATION
AIR IN UNUSUALLY TIGHT CONSTRUCTION.
Page 37
AIR FOR COMBUSTION AND
VENTILATION INSIDE BUILDING
This fresh combustion and ventilation air would come from an adjoining unconfined space.
When ventilating to an adjoining space, you must provide two permanent openings: one
within 12" of the ceiling and one
within 12"
of
the
floor on the
wall connecting the two spaces (See options 1 and 2, Figure 9). You can
also remove door into adjoining room (See option 3, Figure 9).
WARNING
REWORK WORKSHEET, ADDING THE SPACE OF THE ADJOINING UNCONFINED
SPACE. THE COMBINED SPACES MUST HAVE ADEQUATE AMOUNT OF AIR
TO SUPPLY ALL APPLIANCES IN BOTH SPACES.
NOTE: Each opening shall have a minimum free area of 1 square inch per 1000 BTUs per
hour of the total input rating of all gas utilization equipment in the confined space, but
not less than 100 square inch.
Figure 9
Page 38
WARNING
THIS HEATER MUST HAVE ADEQUATE AMOUNT OF AIR FOR PROPER
OPERATION. IF NOT, POOR FUEL COMBUSTION COULD RESULT. READ THE
FOLLOWING INSTRUCTIONS TO ENSURE PROPER AMOUNT OF AIR FOR THIS AND
OTHER FUEL-BURNING APPLIANCES IN YOUR HOME.
AIR FOR COMBUSTION AND
VENTILATION OUTDOORS
Provide extra fresh combustion and ventilation air by using ventilation grills or ducts.
You must provide two permanent openings: one within 12" of the ceiling and one within 12"
of the floor. Connect these items directly to the outdoors. These spaces include attics
and crawl spaces. Follow the National Fuel Gas Code NFPA 54/ANSI Z223.1, Section 5.3,
Air For Combustion and Ventilation for required size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for inlet air into attic if attic has a thermostatcontrolled power vent. Heated air entering the attic will activate the power vent.
Ventilated Attic
Outlet Air
To Attic
Outlet Air
To
Crawl
Space
Inlet Air
Ventilated
Crawl Space
Inlet Air
Figure 10
Page 39
SECTION VI
VENTED
(1) This appliance must be installed only in a solid-fuel burning fireplace with a working flue
and constructed of non-combustible materials.
(2) A minimum of 34 sq. in. (Min. 6" chimney) or see page 41, permanent flue opening must
be provided by either the fireplace chimney or chimney damper to vent the flue gases.
(3) Solid fuels shall not be burned in a fireplace where a decorative appliance is installed.
(4) Any chimney damper must be fixed in a manner which will maintain the minimum
permanent vent opening at all times.See figure 11.
NOTE: See chart on page 41.
Figure 11
MINIMUM FIREPLACE DIMENSIONS FOR LOG SETS MANUFACTURED BY NEW
BUCK CORPORATION FOR SOLID FUEL BURNING FIREPLACE OR MASONRY
FIREPLACE AND PREFAB OR MANUFACTURED FIREPLACES.
NOTE: When using logsets with the Model 19HS heat shield see page 30 for clearances.
MODEL
HEIGHT OF
WIDTH OF
WIDTH AT
DEPTH OF
OPENING
OPENING
REAR
FIREPLACE
AT FRONT
18
17"
25"
18"
14"
24
17"
30"
24"
14"
30
17"
36"
26"
14"
WARNING: A fireplace screen must be in place when the appliance is operating and,
unless other provisions for combustion air are provided, the screen shall have an opening
(s) for introduction of Air For Combustion And Ventilation.
Page 40
(5) See: GAS PRESSURE CHECK, page 17.
(6) See: OPERATING INSTRUCTIONS, pages 18-26.
(7) See: BURNER & PILOT FLAME CHECK, for proper flame pattern, page 30.
(8) See: CLEANING INSTRUCTIONS, page 42.
NOTE: Visually check the pilot and burner flames annually and monthly during seasons that
the appliance is operating frequently. See page 30.
NOTE: “The installation of appliances designed for manufactured home (US only) or mobile
home installation must conform with the Standard CAN/CSA Z240 MH, Mobile Housing, in
Canada or with the Manufactured Home Construction and Safety Standard, Title 24 CFR,
Part 3280, in the United States or when such a standard is not applicable, ANSI/NCSBCS
A225.1/NFPA 501A, Manufactured Home Installations Standard.
WARNING: “Do not use this appliance if any part has been under water. Immediately call
a qualified service technician to inspect the appliance and to replace any part of the control
system and any gas control which has been under water.”
WARNING: “ Keep the appliance area clear and free from combustible materials, gasoline
and other flammable vapors and liquids.”
NOTE: Use a minimum round flue diameter of 7” (inches).
When using as a vented log set, refer to chart below to calculate
minimum damper opening.
FOR MASONRY BUILT FIREPLACES, FREE OPENING AREA OF CHIMNEY DAMPER
FOR VENTING COMBUSTION PRODUCTS FROM DECORATIVE APPLIANCES FOR
INSTALLATION N SOLID FUEL BURNING FIREPLACES.
Appliance Input Rate (kBTU/hr)
20
30
40
50
60
70
80
90
100
110
120
Chimney
Minimum Opening** (sq. in.)
Height* (ft)
6
17.6
25.7
33.8
41.7
49.2
56.6
64.0
71.4
78.8
86.2
93.5
8
16.5
23.7
31.2
38.7
45.5
52.4
59.7
66.9
74.1
81.3
88.6
10
15.1
21.7
28.7
35.2
41.7
48.2
54.3
60.2
66.1
72.0
77.9
15
14.1
19.9
26.1
32.0
37.7
43.2
48.8
54.1
59.4
64.6
69.9
20
12.9
18.5
23.7
28.8
34.3
39.8
44.4
49.1
53.8
58.4
63.0
30
12.2
16.9
21.6
26.5
31.2
35.9
40.3
44.5
48.6
52.7
56.6
* Height is from hearth to top of chimney and the minimum height is 6 feet.
** Chart shows minimum opening (sq. in.) for a given height and input rate.
Page 41
IMPORTANT SAFEGUARDS
Although your gas logs are very realistic in appearance, it is not a real burning fireplace and
must not be used for burning solid fuel.
To avoid irreparable damage to the heater or personal injury, matches, paper, garbage, or any
other material must not be placed or thrown on top of the logs or into the flames.
To avoid personal injury, do not touch hot surfaces when the heater is operating. Close
supervision is necessary when the heater is being operated near children.
NOTE: An annual examination and cleaning of the venting system of the solid-fuel burning
fireplace, must be done by a qualified agency.
WARNING:
ALL THE LOGS ARE MANUFACTURED FROM BONDED
CERAMIC FIBER.
THIS IS A COMMONLY USED MATERIAL IN INDUSTRY
WORLDWIDE. IN THE EVENT OF THE LOG BEING REMOVED, CARE SHOULD BE
TAKEN TO NOT DAMAGE THE BONDED MATERIAL.
INTENTIONAL MISUSE OR DELIBERATELY FRAGMENTING THE MATERIAL COULD
LEAD TO INHALING FIBERS AND BE INJURIOUS TO YOUR HEALTH.
THE HEATER IS INTENDED FOR USE AS A GAS HEATER MOUNTED IN A VENTED
OR VENT-FREE FIREPLACE AS DESCRIBED IN THESE INSTRUCTIONS. IT SHOULD
NOT BE USED FOR ANY OTHER PURPOSE.
CLEANING
CAUTION: BEFORE CLEANING OR MOVING LOGS OR OTHER
PARTS OF THE
HEATER, BE SURE TO READ THE ABOVE SECTION ON “IMPORTANT SAFEGUARDS”.
All cleaning should be carried out when the heater is cold. Only limited cleaning will be required
under normal use. Dusting the front of the base, the top of the piezo cover, or the control knob
panel may be required occasionally. Do not use any cleaning fluids to clean the logs or any
other part of the heater.
If the flames show any unusual shapes or behavior, or if the burners fail to ignite properly,
then the burner holes may require cleaning. If this occurs, it is preferable to contact your nearest
dealer to get your heater serviced.
Alternatively, the heater can be cleaned by removing the top, front, and rear logs. Handle the
logs gently so as not to damage the fiber pieces. Always lift each log by holding it carefully
at each end. Use a vacuum cleaner to carefully remove dust and loose particles from the base,
logs, and from around the burners. Gloves are recommended to prevent the fibers from
breaking your skin. If the skin is broken, wash gently with soap and water.
“WARNING: Failure to keep the primary air opening(s) of the burner(s) clean mat result in
sooting and property damage.”
Page 42
TROUBLESHOOTING
WARNING
TURN OFF, UNPLUG HEATER AND LET COOL BEFORE SERVICING.
ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR
HEATER.
CAUTION
NEVER USE A WIRE, NEEDLE, OR SIMILAR OBJECT TO CLEAN ODS/
PILOT. THIS CAN DAMAGE ODS/PILOT.
OBSERVED
PROBLEM
POSSIBLE
CAUSE
SOLUTION
When igniter button is pressed, 1. Igniter electrode positioned
there is no spark at ODS/PILOT
incorrectly
2. Igniter electrode broken
3. Igniter electrode not
connected to igniter cable
4. Igniter cable pinched or wet
5. Piezo igniter nut is loose
6. Broken igniter cable
7. Bad piezo igniter
OBSERVED
PROBLEM
POSSIBLE
CAUSE
1. Replace igniter
2. Replace igniter
3. Reconnect igniter cable
4. Free igniter cable if pinched
by any metal or tubing. Keep
igniter cable dry.
5. Tighten nut.
6. Replace piezo igniter cable
7. Replace igniter cable
SOLUTION
When igniter button is pressed, 1. Gas supply turned off or
1. Turn on gas supply or open
there is spark at ODS/PILOT but
manual shutoff valve is
manual shutoff valve
no ignition
closed
2. Control knob not in “PILOT” 2. Turn control knob to ”PILOT”
position
position
3. Control knob not pressed in 3. Press in control knob while in
while in “PILOT” position
“PILOT” position.
Page 43
4. Air in gas lines when
installed
5. Depleted gas supply
6. ODS/PILOTt is clogged
7. Gas regulator setting is not
correct
OBSERVED
PROBLEM
POSSIBLE
PROBLEM
ODS/PILOT lights but flame
goes out when control knob is
released
1. Control knob is not fully
pressed in
2. Control knob not pressed in
long enough
3.
4.
5.
6.
7.
4. Continue to hold down control
knob. Repeat igniting
operation until air is removed.
5. Contact local propane gas
company
6. Clean ODS/PILOTt or replace
ODS/PILOTot assembly
7. Replace gas regulator
SOLUTION
1. Press in control knob
completely
2. After ODS/PILOT lights keep
control knob pressed 30
seconds
Safety interlock system has 3. Wait 1 minute for safety
interlock system to reset
been triggered (if equipped)
4. Fully open manual shutoff
Manual shutoff valve not
valve
fully open
5. Hand tighten until snug, then
Thermocouple connection
tighten 1/4 turn
loose at control valve
6. A) Contact local propane gas
Pilot flame not touching
company
thermocouple, which allows
B) Clean ODS/PILOT (See
thermocouple to cool,
Cleaning and Maintenance),
causing pilot flame to go
or replace ODS/PILOT
out. This problem can be
assembly
caused by one or both of the
following:
A) low gas pressure
B) dirty or partially
clogged ODS/ILOT
7. Replace control valve
Control valve damaged
Page 44
OBSERVED
PROBLEM
POSSIBLE
CAUSE
SOLUTION
Burner does not light after ODS/ 1. Burner orifice is clogged
PILOT is lit
2. Inlet gas pressure is too low
Delayed ignition of burner
1. Manifold pressure is too low
2. Burner orifice is clogged
1. Clean burner (see Cleaning
and Maintenance) or replace
burner orifice
2. Contact local propane gas
company
1. Contact local propane gas
company
2. Clean burner (see Cleaning
and Maintenance) or replace
burner orifice
2. Burner damaged
3. Gas regulator defective
1. Clean burner (see Cleaning
and Maintenance) or replace
burner orifice
2. Replace burner
3. Replace gas regulator
Slight smoke or odor during
initial operation
1. Residues from manufacturing
process
1. Problem will stop after a few
hours of operation
Heater produces a whistling
noise when burner is lit
1. Turning control knob to “HI”
position when burner is cold
(if equipped with this type of
valve)
2. Air in gas line
1. Turn control knob to “LOW”
position and allow to warm
for a minute
Burner backfiring during
combustion
1. Burner orifice is clogged or
damaged
3. Air passageways on heater
blocked
4. Dirty or partially clogged
burner orifice
Page 45
2. Operate burner until air is
removed from line. Call
local propane company to
check gas line.
3. Observe minimum
installation clearances
4. Clean burner or replace
orifice
WARNING
IF YOU SMELL GAS:
* SHUT OFF GAS SUPPLY
* DO NOT TRY TO LIGHT APPLIANCE
* DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY
PHONE IN YOUR BUILDING
* IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S
PHONE. FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS.
* IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE
DEPARTMENT.
IMPORTANT: Operating heater where impurities in the air exist may create odors. Cleaning
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc.
create fumes. These fumes may mix with combustion air and create odors.
OBSERVED
PROBLEM
POSSIBLE
CAUSE
SOLUTION
Heater produces a clicking/ticking 1. Metal expands while heating
noise just after burner is lit or shut
or contracts while cooling
off
1. This is common with most
heaters. If noise is
excessive, contact a
qualified service person.
Heater produces unwanted odors
1. Heater burning vapors from
paint, hair spray, glues, etc.
(See “Important” above)
2. Low fuel supply
3. Gas leak (See “WARNING”
above)
1. Ventilate room. Stop using
odor causing products while
heater is running.
2. Refill supply tank.
3. Locate and control all leaks.
See “Checking Gas
Connections”.
Heater shuts off in use
(ODS operates)
1. Not enough fresh air is
available
2. Low line pressure
1. Open window/door for
ventilation
2. Contact local propane
company
3. Clean ODS/PILOT
3. ODS/PILOT is partially
clogged
Gas odor even when control knob 1. Gas leak (See “WARNING”
is in OFF position
above)
2. Control valve defective
Page 46
1. Locate and correct all leaks
(see Checking Gas
Connections)
2. Replace control valve
OBSERVED
PROBLEM
POSSIBLE
CAUSE
SOLUTION
Gas odor during combustion
1. Foreign matter between
control valve and burner
1. Take apart gas tubing and
remove foreign matter
2. Gas Leak. See
2. Locate and correct all leaks
“WARNING” statement at top (See “Checking Gas
of previous page
Connections”)
Page 47
NOTE: You may want to have your chimney cleaned by a professional before installing unit.
SERVICING
Repair and replacement work should only be done by a qualified service person.
Always shut off the gas supply and make sure that heater is cool before beginning any service
operation. Always check for gas leaks after servicing.
REPLACEMENT PARTS
SIT MILLIVOLT VALVE 18”, 24: BASE FOR LOG SETS
A parts list with exploded view follows. Always include correct name, part number and model
number of the heater when ordering service parts.
KEY#
PART DESCRIPTION
1.
1.
2.
3.
4.
5.
PART NUMBER
O.D.S. PILOT (L.P.) O.P. ASSEMBLY
PE 8404C
O.D.S. PILOT (NAT) O.P. ASSEMBLY
PE 8204C
GENERATOR
PILOT TUBE 3/16"
MF 31612 ALMTUB
12" GENERATOR WIRE
“H” BURNER
18"
PO H-BURN001
24"
PO 24H-BURN
30"
PO 24H-BURN
6.
INLET ELBOW
7.
3/8" COMP. NUT & SLEEVE
PH 616 & PH 606
8.
3/8" BURNER SUPPLY TUBE
DX18MV
- 3 pieces 6"
PO T6-06
DX24MV & DX30MV - 1 piece 12"
PO T6-12
- 2 pieces 6"
PO T6-06
9.
12" SWITCH WIRES
PE 12JUMPER
10.
CARLING SWITCH
(AUTO/OFF/MANUAL)
PE RC211RB
11.
PIEZO STRIKER
PE 124461
12.
PIEZO 14" IGNITOR WIRE
PE UL3573
13.
MALE RUN TEE FITTING
PH 64A-66
14.
THERMO-COUPLE
15.
MANIFOLD OUTLET CONNECTOR
PH 68A-6C
24"-30"
16.
ORIFICES
L.P.
18"
REAR
#54
#53
PO 54 & 53 MVORF
FRONT
#60
#60
PO 60 & 60 MVORF
NATURAL 18"
24"-30"
REAR
#44
#41
PO 44 & 41 MVORF
FRONT
#53
#51
PO 53 & 51 MVORF
17.
820 mv. S.I.T. VALVE
LP - PE 820636
NAT - PE 820637
OPTIONAL
CANOPY (HOOD)
MAPSFPC002
Page 48
SIT MILLIVOLT VALVE 18”, 24: BASE
Figure 12
Page 49
REPLACEMENT PARTS
SIT MODULATING OR SIT MANUAL VALVE 18”,24” BASE FOR LOG SETS
PART DESCRIPTION
1.
1.
2.
2.
3.
4.
5.
6.
7.
8.
9.
10.
PART NUMBER
O.D.S. PILOT ASSEMBLY- (LP)
O.D.S. PILOT ASSEMBLY- (NAT)
PILOT TUBE 1/4" x 6"
PILOT TUBE 3/16"
“H” BURNER
18"
24"
30"
INLET ELBOW
3/8" COMP. NUT & SLEEVE
3/8" BURNER SUPPLY TUBE
DX18MV
- 3 pieces 6"
DX24MV & DX30MV - 1 piece 12"
- 2 pieces 6"
PE 12JUMPER
MALE RUN TEE FITTING
THERMO-COUPLE
MANIFOLD OUTLET CONNECTOR
ORIFICES
L.P.
18"
24"-30"
REAR
#54
#53
FRONT
#60
#60
NATURAL
REAR
FRONT
11.
820 mv. S.I.T. VALVE
11.
(SIT) MANUAL VALVE
18"
#44
#53
24"-30"
#41
#51
PE 8402
PE 8251
MF 146ALMTUB
MF 3161ALMTUB
PO H-BURN001
PO 24H-BURN
PO 24H-BURN
PH 616 & PH 606
PO T6-06
PO T6-12
PO T6-06
PH 64A-66
PH 68A-6C
PO 54 & 53 MVORF
PO 60 & 60 MVORF
PO 44 & 41 MVORF
PO 53 & 51 MVORF
LP - PE 0630504
NAT - PE 0630504
PE 0630522
(MUST SPECIFY LP. OR NAT.)
REPAIR PARTS
A parts list with exploded view follows. Always include correct name, part number, and model
number of the heater when ordering service parts. Please contact your local dealer or distributor
when ordering . If one is not available, you may contact.
New Buck Corporation
PO Box 69
200 Ethan Allen Drive
Spruce Pine, NC 28777
Page 50
SIT MODULATING OR SIT MANUAL VALVE 18”,24” BASE
10
8
3
1
10
6
7
6
3
2
4
Page 51
11
NEW BUCK CORPORATION
200 ETHAN ALLEN DRIVE
SPRUCE PINE, NC 28777
We reserve the right to amend these specifications at any time without notice. The only
warranty applicable is
our
standard written
warranty.
We
make
no other warranty, expressed or implied.
LIMITED WARRANTY
VENT-FREE AND VENTED GAS LOGS
New Buck warrants this product to be free from defects in materials and components for two
(2) years from the date of first
purchase,
provided
that the product has
been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or canceled check must be
presented.
This warranty is extended only to the original retail purchaser. This warranty covers only the
cost of part(s) required to restore this heater to proper condition. Warranty part(s)
MUST be obtained through authorized dealers of this product and/or New
Buck who will provide original factory replacement parts. Failure to use original factory
replacement parts voids this warranty. The heater MUST be installed by a qualified installer
in accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition, because of normal
wear and tear, or parts that fail or become damaged as a result of misuse, accidents, lack of
proper maintenance or defects caused by improper installation.
What is not covered:
* Removal and re-installation costs.
* Labor costs for replacement or repairs.
* Transportation or labor costs.
* The cost of a service call to diagnose trouble.
* Painted surfaces.
* Damage or defect caused by improper installation, accident, misuse, abuse, or alteration.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT
GOVERNS THE SALE OF THE PRODUCT, THIS EXPRESS WARRANTY EXCLUDES
ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF
ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY
AND
FITNESS FOR A PARTICULAR PURPOSE TO
ONE (1) YEAR FROM THE DATE OF FIRST PURCHASE. NEW BUCK LIABILITY IS
HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND NEW
BUCK
SHALL NOT
BE LIABLE FOR ANY OTHER DAMAGES
WHATSOEVER
INCLUDING
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Page 52
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion
or limitation of incidental or consequential damages, so the above limitation on implied
warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary
from state to state.
OWNER REGISTRATION
The attached owner registration card must be completed in its entirety and mailed within 30
days from date of installation in order for warranty coverage to begin to:
New Buck Corporation
P.O. Box 69
Spruce Pine, NC 28777
PLEASE NOTE: Owner Registration Card must contain Authorized Buck Stove Dealer
Number and Certified Installer’s number (if applicable) for warranty coverage to begin.
NAME: ____________________________________________________
ADDRESS:_________________________________________________
CITY: _____________________________________________________
STATE: ______________________ ZIP: ________________________
CUSTOMER EMAIL:_________________________________________
MODEL #: _________________________________________________
SERIAL #: _________________________________________________
DATE OF PURCHASE: ______________________________________
DATE OF INSTALLATION:___________________________________
INSTALLER’S NAME: _______________________________________
PURCHASED FROM: _______________________________________
Download PDF