DB Pro Installation Guide
Signal Booster
Installation
Guide
DB Pro™
Adjustable Gain
800/1900 MHz In-Building
Wireless Smart Technology ™
Signal Booster
DB Pro™
Contents:
How it Works. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick Install Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Selecting a Direction for the Outside Antenna. . . . . . . . . 5
Finding the Strongest Signal. . . . . . . . . . . . . . . . . . . . . . 8
Installing the Inside Antenna. . . . . . . . . . . . . . . . . . . . . . 9
Installing a Wilson Electronics Signal Booster. . . . . . . 10
Powering up a Wilson Electronics Signal Booster. . . . . 11
Understanding the Signal Booster Lights . . . . . . . . . . . 13
Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Signal Booster Specifications . . . . . . . . . . . . . Back Cover
Note: This manual contains important safety and operating information. Please read and
follow the instructions in this manual. Failure to do so could be hazardous and result in
damage to your signal booster.
Wilson
®
Electronics, Inc.
Installation Instructions for the Following Wilson
Electronics Signal Booster:
DB Pro™ Adjustable Gain In-Building Wireless
800/1900 MHz Smart Technology ™ Signal Booster
Model # 271265
FCC ID: PWO271265 IC: 4726A-271265
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met.
How it Works
Wilson Electronics signal boosters are bi-directional devices that
deliver service levels consistent with what would be expected in areas
of high cell network coverage. The outside antenna will collect the cell
tower signal and send it through the cable to the signal booster. The
signal is then boosted and sent to the inside antenna. Your cell phone
or data card then communicates with the improved signal. When the
cellular device transmits, the signal goes through the inside antenna,
is boosted by the signal booster and broadcasted to the cell tower
through the outside antenna.
Inside this Package
DB Pro™
Signal Booster
AC/DC Power Supply
Accessories & Antenna Options
1. 1900 MHz Yagi PCS Antenna (301124)*
2. 800 MHz Yagi Cellular Antenna (301129)*
3. Wide Band Directional Antenna
700 MHz - 2700 MHz (304411)
1
2
4. Wide Band Panel Antenna 700-2700 MHz (301155)
5. 75 Ohm Lightning Surge Protector (859988)
6. 2-way splitter 700-2300 MHz (859959)
3
4
5
6
*Requires N-Male to F-Female adapter/converter (971128)
To purchase call Wilson Sales Department at: 800-204-4104
1
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
Quick Install Overview
See Installation Diagram on pages 3 & 4. Contact Wilson Electronics
Technical Support Team with any questions at 866-294-1660.
1. Select a location to install the signal booster that is away
from excessive heat, direct sunlight, moisture and has proper
ventilation. Do not place the signal booster in an air-tight
enclosure.
2. Select a location on the roof of the building to install the outside
antenna. Use a cell phone in test mode to find the strongest signal
from the cell tower. Visit www.WilsonElectronics.com to find test
mode function for your particular cell phone or see page 8.
3. Select a location for the inside antenna, preferably in the
center of where the signal needs to be amplified. A minimum
separation distance (combined vertical/horizontal) of 15
feet is necessary for operation. If the inside coverage is not
sufficient you may need as much as 50 feet of separation. See
installation diagram on pages 3 & 4.
4. Run the outside antenna cable to the signal booster and attach
it to the connector labeled “outside antenna” on the signal
booster. Run the inside antenna cable to the signal booster
and attach it to the connector labeled “inside antenna” on the
signal booster.
5. Before powering up the signal booster, verify that both the
outside antenna and the inside antenna are connected and
check that all connections are tight. Lightning surge protection
is recommended for all in-building installations. See page 7.
Note: Be careful when plugging the connectors in so as not to
bend the center pins on the connectors. See page 10 for more
information.
6. The Signal Booster has been packaged with the gain control
knobs adjusted to the highest gain position. If one or both of
the lights are not green please refer to pages 13 &14.
7. Warning: Connecting the signal booster directly to a cell phone
with use of an adapter will damage the cell phone and the
signal booster.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
2
AG DB Pro Installation Diagram
Outside
Antenna
(Wide Band
Antenna option
shown)
Note: The inside panel antenna
may be mounted on the wall
directly under the outside
antenna if 15 feet of vertical/
horizontal separation can be
maintained. The preferred
method for the best coverage,
place the antenna in the ceiling.
Null Zone: The area under
the antenna, where the
antenna radiates the least.
Note: A lightning surge protector
is recommended for all building
installations. Make sure the
protector is installed in line
between the outside antenna and
the signal booster.
(i
in
Inside Panel
Antenna
(Optional
second
antenna for
additional
coverage).
Typical Installation
3
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
Before Getting Started
This guide will help you properly install your Wilson Electronics
Signal Booster. It is important to read through all of the
installation steps for your particular application prior to
installing any equipment. Read through the instructions,
visualize where all the equipment will need to be installed and do
a soft installation before mounting any equipment. Contact
Wilson Electronics Technical Support Team with any questions
at: 866-294-1660.
2-way/3-way/
4-way splitter
(if using multiple
inside antennas)
Lightning
Surge Protector
(Recommended)
Inside Panel
Antenna
(Optional third
antenna for
additional
coverage).
Signal
Booster
Power
Supply
n
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
4
Selecting a Direction for the Outside Antenna
Select a location on the roof of the building to install the outside
antenna. Use a cell phone in test mode to find the strongest signal
from the cell tower. To get the strongest signal possible, it is very
important to set up your outside antenna properly. The inside and the
outside antenna must be mounted in such a way that they are able to
pick up the best possible cellular signal on the outside of the building
and provide the best possible signal on the inside of the building.
Mount the outside antenna as high as possible facing the cell tower in
an area with the best possible signal coverage. Note: Never point the
front of a directional antenna toward the inside antenna. See Figure
1 & 2 on page 12.
Reasons for Weak Cellular Signals
Anyone who uses a cell phone or cellular data card knows the
frustration of not being able to connect to or maintain a strong
cellular signal. When this occurs, it is generally due to one of two
reasons:
1. Location of the Nearest Cell Tower – Cell towers are situated
to provide broad coverage; however, there are many areas in
which signal strength may be reduced by topographic features
or by local government restrictions on the height or placement
of the towers themselves. Rural areas generally have fewer cell
towers than urban regions.
2. Natural and Man-Made Obstructions – Signal strength can
also be negatively affected by trees, hills, weather, buildings,
and other obstructions. You may be relatively close to a cell
tower but still unable to make a call. This often occurs in homes,
offices and other buildings in which stucco, concrete or metal
walls may block the signal.
The Signal Booster works with two antennas. The inside antenna
communicates with your cellular device and the outside antenna
communicates with the cell tower. The outside antenna receives the
cell tower signal and sends it through the coax cable to the Signal
Booster, where it is amplified and re-transmitted much stronger
through the inside antenna into the room. When the inside antenna
5
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
picks up a signal from your cellular device, the signal booster
amplifies that signal and transmits it through the cable to the outside
antenna and back to the cell tower. (Note: The Signal Booster will
only operate if there is an adequate signal to amplify.)
Finding the Strongest Signal
Cell Signal
Outside
Wide Band
Antenna
Cell Tower
When installing your signal booster’s outside antenna, aiming
it towards the best signal source from your service provider is
important. The best way of getting the strongest signal is to have
one person on the roof to rotate the outside antenna, which
is connected to the signal booster, while the second person is
watching the signal strength on the phone inside the building. This
allows you to read the signal strength from the cell tower. Turn the
outside antenna 45 degrees at a time. It is preferable to have the
phone in the test mode so the numerical signal strength can be
read since bars are not the most accurate. Go to the website
www.WilsonElectronics.com for help in finding the test mode for
your phone. Always make sure the person inside the building gives
the signal time to arrive and register on the phone. (Between
10-30 seconds for phone to reset to the new signal reading).
Signal readings usually appear as a negative number (for example,
-86). The closer you get to zero the stronger the signal. (See figure
below).
Signal Strength Figure
EXCELLENT
-50dB
-60dB
GOOD
-70dB
-80dB
POOR
-90dB
-100dB
NO
SIGNAL
-110dB
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
6
Outside Antenna Installation
Wide Band Antenna option shown
Drip hole on bottom
Cell
Cell Tower
Tower
Note: Use the directions included with your choice of antenna,
the instructions here are meant for the Wide Band Antenna option
shown above. The antenna should be mounted as shown in the
illustration above. The included mounting bracket is adjustable
and will accommodate pipe diameters from 1.25” to 2” (pipe sold
separately). Mount the antenna so that there is at least 3 feet of
clearance in all directions around it. Position the antenna so that
it has an unobstructed line of sight to the cell tower’s strongest
signal. Make sure the antenna is not pointing across your own roof
or at the inside antenna as this will cause the oscillation (feedback)
protection circuitry to shut down the signal booster. See page 12.
Warning: Lightning protection is recommended for all installations.
(Part# 859988). Take extreme care to ensure that
neither you nor the antenna comes near any electric power lines.
Installing Lightning Protection
Install the Lightning Surge Protector
(LSP) close to the signal booster. Attach
the cable from the outside antenna to the
surge protector. Using a short length of
low loss cable, attach one end to the LSP
and the other to the outside antenna.
Ensure the LSP is properly grounded.
(For RG6 cable use #859988-75 Ohm).
(For Wilson 400, RG-58, RG-174 cable
use #859902-50 Ohm, shown in picture).
7
From the
outside
antenna
Lightning Surge
Protection
Ground Wire
To the Signal Booster
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
Mounting Tips for Running Outside Antenna Cable
If you are mounting the outside antenna on the roof of your building,
we have found that it is easiest to run your cable underneath the
down side of your roof’s flashing. If you have satellite TV service
installed at your home or office, you may be able to follow the
same route as the satellite TV cables that are already running from
the outside of your building to the inside. After routing the cable,
we recommend sealing any areas where the cable passes into
the building with silicone or other waterproof sealant to keep your
installation from leaking. If you are mounting the outside antenna to
the outside wall of your home or building, the simplest way is to run
the coaxial cable on the outside of the wall and attach it to the exterior
of your home or office. Then drill a hole through the wall where you
want the cable to appear on the inside of the building. Before drilling,
make sure that there are no electrical
outlets, sewer or water pipes, or
electrical wiring in the wall that you
are about to drill through as this could
potentially harm you or damage the
building.
After drilling the required hole, run
the cable through and seal it with
cable bushings or a siliconetype sealant to enclose the
hole that you have created.
In some instances, it may
be possible to run the cable
up into the fascia of the
attic overhang. In this
circumstance, the cable
will be accessible in the attic
for further routing.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
8
Installing the Inside Antenna for DB Pro
Find the desired location for the inside panel antenna. Verify that the
inside panel antenna and the outside antenna have the necessary
separation (Minimum of 15 vertical/horizontal feet if installed with
signal booster set at a lower gain, for maximum gain you may need
as much as 50 feet of separation). For optimum results the antenna
should be mounted at least 6 feet off the ground.
Inside
Antenna
Ceiling
In some cases, multiple inside antennas may be required if you
have multiple rooms with poor signal. A signal may be split by
using a splitter. See configuration on pages 3 & 4. Wide Band
Panel Inside Antenna (Included in some kits)
Warning: There must
be at least a 15 inch
separation distance
between the inside
antenna and all
persons.
9
Wide Band
Panel Inside
Antenna
(Included in
some kits)
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
Installing a Wilson Electronics Signal Booster
Select a location to install the signal booster that is away from
excessive heat, direct sunlight, moisture and that has proper
ventilation. Do not place the signal booster in an air-tight
enclosure.
Recommended installation locations for in-building signal boosters
are:
• On a shelf
• In a closet
• Near a power outlet.
Note: It is important to have adequate air ventilation. Maintain
at least 6 inches of clearance from surrounding objects. Run the
outside antenna cable to the signal booster and attach it to the
connector labeled “outside antenna” on the signal booster. Run
the inside antenna cable to the signal booster and attach it to the
connector labeled “inside antenna” on the signal booster.
Note: Be careful when
plugging the connector in to
avoid bending the center pins
on the connectors.
DB Pro™
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
10
Powering up a Wilson Electronics Signal Booster
1. Never point the front of a directional outside antenna toward the
inside antenna. See Figure 2 on page 12.
2. Ensure that both the outside antenna coax cable and the inside
antenna coax cable are connected to the signal booster and the
connections are tight before powering up the signal booster.
3. Plug the 6-volt power supply into the signal booster input
marked “POWER” (carefully, to avoid damaging the center pin)
and then into a wall outlet.
4. If the signal booster does not have a green light, please see
pages 13 & 14.
5. If you know that only one frequency band (800 or 1900) is
available in your coverage area (or going to be used), reduce
the gain control on the frequency band that is NOT in use to the
lowest setting. This will reduce the power consumption of the
signal booster.
6. Using multiple signal boosters in one installation may cause
interference to the cell tower.
7. Contact Wilson Electronics Technical Support Team with any
questions at 866-294-1660 or email [email protected]
Technical Support hours are 7 am to 6 pm MST.
DB Pro™
11
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
Figure 1
CORRECT INSTALLATION
Point antennas away from each other
Outdoor
Antenna
Inside Panel
Antenna
Signal Booster
Figure 2
INCORRECT INSTALLATION
Never point antennas toward each other
Outdoor
Antenna
Inside Panel
Antenna
Signal Booster
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
12
Understanding the Signal Booster Lights and
Troubleshooting
During installation mode the signal booster is resetting itself very
quickly to aid the installer. The Signal Booster is equipped with
two indicator lights, one for the 800 MHz band and the other for
the 1900 MHz band. For the first 15 minutes that the booster is
plugged in, it is programed for a test and alignment period. During
this time, both lights will do one of the following 4 things:
Note: If after the initial 15 minutes you are not done with the
installation, the signal booster can be reset and enter installation
mode again by disconnecting and reconnecting the power supply
from the booster.
1. Blinking Green
If the signal booster is blinking green, the signal booster is
operating properly. If you are happy with the coverage area in
your building, then you are done. Blinking will stop after the 15
minute installation period.
2. Blinking Orange
The signal booster is experiencing receiver overload. The signal
booster has protection shutoff circuits to prevent the disruption
of cell towers. If one or both lights are blinking orange, this
indicates that the booster has shut down due to close proximity
to a cell tower. First, turn down the gain control on the band
that is blinking until you get a blinking green light. The
booster is now working with reduced gain. If the gain is not
13
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
adequate for good coverage, you will need to turn the gain
to maximum and then turn the outside antenna away from
the cell tower until the light turns to blinking green. If the
booster will not respond, turn the gain down 5 dB and move the
outside antenna. Continue to adjust the gain and the antenna
position until the light turns blinking green. Contact Wilson
Electronics Technical Support Team for assistance:
866-294-1660.
3. Solid Red
If either of the two lights on the signal booster are solid red,
this indicates that the signal booster has shut down on that
frequency to prevent an oscillation. First, make sure that all the
connections are tight. Then reduce the gain of the booster
in small increments by rotating the gain control, counterclockwise, waiting 5 seconds between each adjustment
for the booster to reset. Continue this adjustment until the
light turns blinking or solid green. When you are turning
down the gain, you are reducing the inside coverage area. If
the amount of coverage area is sufficient for your needs and
the light is green the installation is complete. If the coverage
area is not large enough, it is necessary to increase the
separation distance of the antennas by moving them
horizontally or vertically farther apart, or both. Then
increase the gain until the red light comes on, and then
slightly keep decreasing the gain until the green or
blinking green light appears. If after separating the antennas
your coverage area is still too small, contact Wilson Electronics
Technical Support Team for assistance: 866-294-1660.
If your installation takes longer than 15 minutes, it is possible
to re-enter the installation mode by disconnecting and
reconnecting the power supply from the signal booster.
4. SOLID Green
The indicator lights on the signal booster will be a solid green
after the first 15 minute installation period and the unit is
powered up and working properly.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
14
Warnings
Warning:The directional antenna must always be located so
the back or side points to the inside antenna. Never
point the front of the outside antenna toward the
inside antenna – this is to prevent oscillation.
Warning:Connecting the signal booster directly to the cell phone
with use of an adapter will damage the cell phone.
Warning:Use only the power supply provided in this package.
Use of a non-Wilson Electronics product may
damage your equipment.
Warning:RF Safety: FCC regulations require that any fixed
outside antenna used with this signal booster may
not have gain (less cable loss) that exceeds 15
dBi and must be located at least 30 inches from all
people. Inside antennas must not exceed 7 dBi gain
(less cable loss) in the 800 MHz band or 10 dBi gain
(less cable loss) in the 1900 MHz band and must be
located at least 8 inches from all people.
Warning:Verify that both the outside antenna and the inside
antenna are connected to the signal booster before
powering up the signal booster.
Warning:Lightning surge protection is recommended for all
in-building installations.
15
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
About Wilson Electronics
Wilson Electronics, Inc. has been a leader in the wireless
communications industry for over 40 years. The company
designs and manufactures signal boosters, antennas and related
components that significantly improve cellular telephone signal
reception and transmission in a wide variety of applications, both
mobile and in-building. With extensive experience in antenna and
signal booster research and design, the company’s engineering
team uses a state of the art testing laboratory, including an
anechoic chamber and network analyzers, to fine-tune antenna
designs and performance. For its signal boosters, Wilson
Electronics uses a double electrically insulated RF enclosure and
cell tower simulators for compliance testing.
Wilson Electronics signal boosters feature patented Smart
Technology ™ that enables them to automatically adjust their
power based on cell tower requirements. By detecting and
preventing oscillation (feedback), signal overload and interference
with other users, these Smart Technology ™ signal boosters
improve network cell phone areas without compromising carrier
systems. All products are engineered and assembled in the
company’s 55,000-square-foot headquarters in St. George, Utah.
Wilson Electronics has product dealers in all 50 states as well as
in countries around the world.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
16
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson
Electronics 30-day money-back guarantee. If for any reason the
performance of any product is not acceptable, simply return the
product directly to the reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics Signal Boosters are warranted for one (1) year
against defects in workmanship and/or materials. Warranty cases
may be resolved by returning the product directly to the reseller
with a dated proof of purchase.
Signal Boosters may also be returned directly to the manufacturer
at the consumer’s expense, with a dated proof of purchase and a
Returned Material Authorization (RMA) number supplied by Wilson
Electronics. Wilson Electronics shall, at its option, either repair
or replace the product. Wilson Electronics will pay for delivery of
the repaired or replaced product back to the original consumer if
located within the continental U.S.
This warranty does not apply to any signal booster determined
by Wilson Electronics to have been subjected to misuse, abuse,
neglect, or mishandling that alters or damages physical or
electronic properties.
RMA numbers may be obtained by phoning Technical Support at
866-294-1660.
17
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
Disclaimer: The information provided by Wilson Electronics,
Inc. is believed to be complete and accurate. However, no
responsibility is assumed by Wilson Electronics, Inc. for any
business or personal losses arising from its use, or for any
infringements of patents or other rights of third parties that
may result from its use.
Copyright © 2011 Wilson Electronics, Inc. All rights reserved.
Operation is subject to the following two conditions: (1) This
device may not cause interference and (2) this device must accept
any interference, including interference that may cause undesired
operation of this device.
One or more of the following U.S. Patent numbers may apply
to the Signal Booster in this product – D596,614; D596,615;
D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186; 7,783,318;
7,684,838; 12,714,994.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected] Hours: 7 am to 6 pm MST.
18
Signal Booster Specifications
IC: 4726A-271265
FCC ID: PWO271265
DB Pro
Specifications
Model Number
271265
Antenna connectors
F-Female
Antenna impedance
75 ohms
6.5 x 4.5 x 1.75 inch
(16.5 x 11.4 x 4.4 cm)
Dimensions
Weight
0.47 lbs (0.213 kg)
Frequency
1
824-894 MHz / 1850-1990 MHz
Passband Gain (nominal)
800 MHz * 1900 MHz
2
20 dB Bandwidth (nominal)
Downlink
800 MHz
45 MHz
1900 MHz
88 MHz
Power Output
4
800 MHz
1900 MHz
Power output for single cell phone (uplink)
30.8 dBm
30.5 dBm
Power output for single received channel (downlink)
26.0 dBm
25.2 dBm
Power output for multiple transmitted channels (uplink)
The maximum power is reduced
by the number of channels:
4
62 / 65 dB
Maximum Power
Number of channels
800 MHz
1900 MHz
2
24.0 dBm
21.3 dBm
3
20.5 dBm
17.8 dBm
4
18.0 dBm
15.3 dBm
5
16.0 dBm
13.3 dBm
6
14.5 dBm
11.8 dBm
Number of channels
800 MHz
1900 MHz
2
24.8 dBm
23.7 dBm
3
21.3 dBm
20.2 dBm
4
18.8 dBm
17.7 dBm
5
16.8 dBm
15.7 dBm
6
15.3 dBm
Power output for multiple received channels (downlink)
The maximum power is reduced
by the number of channels:
Noise Figure (typical downlink/uplink)
Isolation
Power Requirements
Maximum Power
14.2 dBm
3.5 dB nominal / 6 dB nominal
> 90 dB
110-240 V AC, 50-60 Hz, 8 W
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband
amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating
would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power
reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [email protected]
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular
www.facebook.com/WilsonCellular
AIG #110892 - Rev002 - 05.17.11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement