Dimplex | SI 10 MR | Operating instructions | Dimplex SI 10 MR Operating instructions

Sole/WasserWärmepumpe für
Innenaufstellung
Installation and
Operating Instructions
English
Montage- und
Gebrauchsanweisung
Instructions d’installation
et d’utilisation
Brine-to-Water
Heat Pump for
Indoor Installation
Bestell-Nr. / Order no. / No de commande : 452233.66.02
Deutsch
8 MR
10 MR
12 TR
14 TR
16 TR
20 TR
Français
SI
SI
SI
SI
SI
SI
Pompe à chaleur
eau glycolée-eau
pour installation
intérieure
FD 8803
Table of contents
1
Please read immediately...............................................................................................................E-2
1.1 Important information.............................................................................................................................. E-2
1.2 Legal Regulations and Directives ........................................................................................................... E-2
1.3 Energy-Efficient Use of the Heat Pump .................................................................................................. E-2
2
Purpose of the Heat Pump ...........................................................................................................E-2
3
Basic Device ..................................................................................................................................E-3
4
Accessories ...................................................................................................................................E-3
4.1 Brine circuit manifold .............................................................................................................................. E-3
5
Transport........................................................................................................................................E-3
6
Installation .....................................................................................................................................E-4
6.1 General Information ................................................................................................................................ E-4
6.2 Acoustic Emissions................................................................................................................................. E-4
7
Installation .....................................................................................................................................E-4
7.1
7.2
7.3
7.4
8
General Information ................................................................................................................................ E-4
Heating System Connection ................................................................................................................... E-4
Heat Source Connection......................................................................................................................... E-5
Electrical Connection .............................................................................................................................. E-5
Start-up...........................................................................................................................................E-5
8.1 General Information ................................................................................................................................ E-5
8.2 Preparation ............................................................................................................................................. E-5
8.3 Start-Up Procedure................................................................................................................................. E-5
9
Description of the Control System Functions ............................................................................E-6
9.1
9.2
9.3
9.4
Operator Controls ................................................................................................................................... E-6
Heating Function..................................................................................................................................... E-6
Cooling Function..................................................................................................................................... E-6
Hot Water Function................................................................................................................................. E-6
10 Maintenance and Cleaning ...........................................................................................................E-7
10.1 Maintenance ........................................................................................................................................... E-7
10.2 Cleaning of Heating Side ........................................................................................................................ E-7
10.3 Cleaning the Heat Source System.......................................................................................................... E-7
11 Faults and Trouble-shooting........................................................................................................E-7
12 Decommissioning/Disposal .........................................................................................................E-7
13 Device Information ........................................................................................................................E-8
Anhang / Appendix / Annexes ............................................................................................................ A-I
www.dimplex.de
E-1
English
2.1 Application .............................................................................................................................................. E-2
2.2 Operating Principle ................................................................................................................................. E-2
1
1
Please read
immediately
1.1
Important information
ATTENTION!
The heat pump is not secured to the wooden pallet.
ATTENTION!
The heat pump must not be tilted more than 45° (in any direction).
English
ATTENTION!
1.3
Energy-Efficient Use of the
Heat Pump
By operating this heat pump you are helping to protect our environment. The heating or cooling system and the heat source
must be properly designed and dimensioned to ensure efficient
operation. It is particularly important to keep water flow temperatures as low as possible in heating operation. All connected energy consumers should therefore be suitable for low flow temperatures. Raising the heating water temperature by 1 K
corresponds to an increase in energy consumption of approx.
2.5 %. Low-temperature heating systems with flow temperatures
between 30 °C and 50 °C are optimally suited for energy-efficient
operation.
Do not use the holes in the panel assemblies for lifting the device!
ATTENTION!
Flush the heating system prior to connecting the heat pump.
2
ATTENTION!
In the case of large-volume heating circuits, use an additional expansion
vessel to supplement the installed expansion vessel.
ATTENTION!
Insert a dirt trap in the heat source inlet of the heat pump to protect the
evaporator against the ingress of impurities.
ATTENTION!
The brine solution must contain at least 25 % of an antifreeze agent on a
mono-ethylene glycol or propylene glycol basis and must be mixed prior
to filling.
ATTENTION!
When there is danger of frost, the circulating pump will also start
immediately in standby mode after connecting the power supply.
ATTENTION!
To prevent the accumulation of deposits (e.g. rust) we recommend using
a suitable corrosion protection system.
ATTENTION!
Any work on the heat pump may only be performed by authorised and
qualified after-sales service technicians.
ATTENTION!
Disconnect all electrical circuits from the power source prior to opening
the device.
1.2
Legal Regulations and
Directives
This heat pump conforms to all relevant DIN/VDE regulations
and EU directives. Refer to the EC Declaration of Conformity in
the appendix for details.
The heat pump must be connected to the power supply in compliance with all relevant VDE, EN and IEC standards. Any further
connection requirements stipulated by local utility companies
must also be observed.
The heat pump is to be connected to the heat source system and
the heating or cooling system in accordance with all applicable
regulations.
E-2
2.1
Purpose of the Heat
Pump
Application
The brine-to-water heat pump is designed for use in existing or
newly built heating systems. Brine is used as the heat transfer
medium in the heat source system. Borehole heat exchangers,
ground heat collectors or similar systems can be used as the
heat source.
2.2
Operating Principle
Heating
The heat generated by the sun, wind and rain is stored in the
ground. This heat stored in the ground is collected at a low temperature by the brine circulating in the ground heat collector, the
borehole heat exchanger or a similar system. A circulating pump
then conveys the “heated” brine to the evaporator of the heat
pump. There the heat is given off to the refrigerant in the refrigerating cycle. This cools the brine so that it can once again absorb
thermal energy in the brine circuit.
The refrigerant is drawn in by the electrically driven compressor,
compressed and “pumped” to a higher temperature level. The
electrical power needed to run the compressor is not lost in this
process. Most of it is absorbed by the refrigerant.
Subsequently, the refrigerant is passed through the condenser
where it transfers its heat energy to the heating water. Depending on the set operating point (thermostat setting), the heating
water is thus heated up to a max. of 60 °C.
Cooling
The functions of the evaporator and the liquifier are reversed in
the “Cooling” operating mode.
The heating water gives up its heat to the refrigerant via the liquifier which is now functioning as an evaporator. The refrigerant is
pumped to a higher temperature level using the compressor.
Heat passes into the brine via the liquifier (evaporator in heating
operation) and consequently into the ground.
5
3
Basic Device
4
The basic device consists of a ready-to-use heat pump for indoor
installation, complete with sheet metal casing, control panel and
integrated control system. The refrigerating cycle contains the refrigerant R407C. R407C refrigerant is CFC-free, non-ozone depleting and non-combustible.
All components required for the operation of the heat pump are
located on the control panel. The power feed for the load current
and the control current must be installed by the customer.
Accessories
4.1
Brine circuit manifold
The brine circuit manifold merges the individual collector loops of
the heat source system into a single main pipe which is connected to the heat pump. Integrated ball valves allow the individual brine circuits to be shut off for de-aeration purposes.
English
The collector including the brine manifold must be provided by
the customer.
5
Transport
A lift truck is suited for transporting the unit on a level surface.
Carrying straps may be used if the heat pump needs to be transported on an uneven surface or carried up or down stairs. These
straps can be passed directly underneath the wooden pallet.
ATTENTION!
The heat pump is not secured to the wooden pallet.
1)
Liquifier
2)
Control panel
3)
Compressor
4)
Heating pump
5)
Evaporator
6)
Primary pump
ATTENTION!
The heat pump must not be tilted more than 45° (in any direction).
Use the holes provided in the sides of the frame to lift the unit
without the pallet. The side panel assemblies must be removed
for this purpose. Any commercially available length of pipe can
be used as a carrying aid.
ATTENTION!
Do not use the holes in the panel assemblies for lifting the device!
www.dimplex.de
E-3
6
6
6.1
Installation
General Information
The unit must be installed indoors on a level, smooth and horizontal surface. The entire base of the frame should lie directly on
the floor to ensure a good soundproof seal. If this is not the case,
additional sound insulation measures may be necessary.
English
The heat pump must be installed so that maintenance work can
be carried out without being hindered. This can be ensured by
maintaining a clearance of approx. 1 m in front of and on each
side of the heat pump.
7
Installation
7.1
General Information
The following connections need to be established on the heat
pump:
„ Flow and return flow of the brine system
„ Flow and return flow of the heating system
„ Power supply
„ Outflows for the pressure relief valves
7.2
Heating System Connection
ATTENTION!
Flush the heating system prior to connecting the heat pump.
Before connecting the heating water system to the heat pump,
the heating system must be flushed to remove any impurities,
residue from sealants, etc. Any accumulation of deposits in the
liquifier could cause the heat pump to completely break down.
Once the heating system has been installed, it must be filled, deaerated and pressure-tested. The pressure indicator is located
on the control panel.
Minimum heating water flow rate
6.2
Acoustic Emissions
The heat pump operates silently due to efficient sound insulation.
To prevent vibrations from being transmitted to the foundation, a
suitable, sound dampening rubber mat should be placed underneath the base frame of the heat pump.
To prevent any sound from being transmitted to the heating system, we recommend connecting the heat pump to the heating
system by means of hose sections.
The minimum heating water flow rate through the heat pump
must be assured in all operating states of the heating system.
This can be accomplished, for example, by installing either a
manifold without differential pressure or an overflow valve. The
procedure for adjusting an overflow valve is described in the
Chapter Start-Up.
Antifreeze protection for installation locations
prone to frost
The antifreeze function of the heat pump controller is active
whenever the heat pump is ready for operation. If the heat pump
is taken out of service or in the event of a power failure, the system has to be drained. The heating circuit should be operated
with a suitable antifreeze if heat pump systems are implemented
in buildings where a power failure can not be detected (holiday
home).
The integrated expansion vessel has a volume of 8 litres. The
volume should be checked by the heating system engineer. Install an additional expansion vessel if necessary.
ATTENTION!
In the case of large-volume heating circuits, use an additional expansion
vessel to supplement the installed expansion vessel.
E-4
8.3
Heat Source Connection
The following procedure must be observed when connecting the
heat source:
Connect the brine pipe to the heat pump flow and return.
ATTENTION!
Insert a dirt trap in the heat source inlet of the heat pump to protect the
evaporator against the ingress of impurities.
In addition, a breather must be installed at the highest point in the
heat source system.
The brine liquid must be produced prior to charging the system.
The liquid must have an antifreeze concentration of at least 25 %
to ensure frost protection down to -14 °C.
Only monoethylene glycol or propylene glycol-based antifreeze
may be used.
The heat source system must be de-aerated and checked for
leaks. The pressure indicator is located on the control panel.
ATTENTION!
The brine solution must contain at least 25 % of an antifreeze agent on a
mono-ethylene glycol or propylene glycol basis and must be mixed prior
to filling.
7.4
Electrical Connection
Connect the mains supply cable to the control panel of the heat
pump via terminal X1.
ATTENTION!
When there is danger of frost, the circulating pump will also start
immediately in standby mode after connecting the power supply.
All electrical components required for the operation of the heat
pump are located on the control panel.
Heat pump - special tariff
Many utility companies offer a special agreement with a lower
electricity tariff when heat pumps are implemented. In return, the
utility company is able to block the heat pump at times of peak
demand.
If this is the case, the customer must provide an all-pole disconnecting device with a contact gap of at least 3 mm (e.g. utility
blocking contactor or power contactor) as well as a circuit breaker with common tripping for all external conductors. The required cross-sectional area of the conductor is to be selected according to the power consumption of the heat pump, the
technical connection requirements of the relevant utility company
as well as all applicable regulations. Details on the power consumption of the heat pump are listed on both the product information sheet and the type plate. The connection terminals are
designed for a max. conductor cross-section of 10mm2.
www.dimplex.de
8
Start-up
8.1
General Information
To ensure that start-up is performed correctly, it should only be
carried out by an after-sales service technician authorized by the
manufacturer. This will lead, under certain circumstances, to an
extension of the warranty period (cf. Warranty). Start-up should
be carried out in heating operation.
8.2
Preparation
The following items need to be checked prior to start-up:
„ All of the heat pump connections must be established as described in Chapter 7.
„ The heat source system and the heating circuit must have
been filled and checked.
„ The dirt trap must have been inserted in the brine inlet of the
heat pump.
„ All valves that could impair proper flow in the brine and heating circuits must be open.
8.3
Start-Up Procedure
The heat pump is started up using the switch (1).
If an overflow valve is fitted to maintain the minimum heating
water flow rate, the valve must be adapted to the requirements of
the heating system. Incorrect adjustment can lead to faulty operation and increased energy consumption. We recommend carrying out the following procedure to correctly adjust the overflow
valve:
Close all of the heating circuits that may also be closed during
operation (depending on the type of heat pump usage) so that
the most unfavourable operating state - with respect to the water
flow rate - is achieved. This normally means the heating circuits
of the rooms on the south and west sides of the building. At least
one heating circuit must remain open (e.g. bathroom).
The overflow valve should be opened far enough to produce the
maximum temperature spread between the heating flow and return flow listed in the table below for the current heat source temperature. The temperature spread should be measured as close
as possible to the heat pump. The heating element of mono energy systems should be disconnected.
Heat source
temperature
From
To
Max. temperature spread
between heating flow and
return flow
-5 °C
0 °C
10 K
1° C
5° C
11 K
6° C
9° C
12 K
10° C
14° C
13 K
15° C
20° C
14 K
21° C
25° C
15 K
E-5
English
7.3
9
9
Description of the
Control System
Functions
9.1
English
9.2
Start the heat pump by moving the switch (1) to the on position
(I). Preselect heating operation by moving the switch (2) to the
heating position ( ). Turn the rotary knob (4) to set the desired
return flow temperature. The potentiometer can be used to request a temperature in the range between a min. of 20 °C and a
max. of 55 °C. The actual temperature can be read from the indicator (3) on the control panel. Once the set temperature is
reached, the heat pump switches off. The heat pump switches on
again when the return flow temperature falls to 4 Kelvin below the
set value. It is not possible to re-start the heat pump until after a
minimum pause time of 5 minutes. If the flow temperature is
higher than 60 °C or the brine temperature is too low, the heat
pump switches off.
Operator Controls
1)
Switch on/standby
2)
Switch heating/cooling
3)
Indicator (illuminates if HP voltage is on)
4)
Setpoint potentiometer (return flow)
5)
Pressure indicator for brine circuit
6)
Pressure indicator for heating circuit
7)
Temperature indicator for heating circuit
Switch (1) switches the heat pump to ready (I) or to standby
mode ( ).
The heat circulating pump operates continuously in the switch
position (l). There is a 10-minute delay when switching from heating to cooling operation and vice versa.
Heating Function
9.3
Cooling Function
Start the heat pump by moving the switch (1) to the on position
(I). Preselect cooling operation by moving the switch (2) to the
cooling position ( ). Turn the rotary knob (4) to set the desired
return flow temperature. The potentiometer can be used to request a temperature in the range between a min. of 12 °C and a
max. of 25 °C. Once the set temperature is reached, the heat
pump switches off. The heat pump switches on again when the
return flow temperature rises to 4 Kelvin above the set value. It is
not possible to re-start the heat pump until after a minimum period of 5 minutes. If the flow temperature is under 7 °C, the heat
pump switches off.
To prevent condensation from forming on the system’s cooling
surfaces, we recommend installing dew point monitors at vulnerable points in the cooling distribution system. Connect them to
the terminal X1 (1,2). If condensation then forms, the cooling of
the system is interrupted.
9.4
Hot Water Function
This heat pump can also be used to heat hot water.
Hot water preparation is requested via the terminal “X1-9” using
an external thermostat to be provided by the customer. This thermostat simultaneously switches on the phase (L) to terminal “X19” and the hot water circulating pump.
A suitable thermostat is available as an accessory.
1)
On = Compressor running
2)
On = Brine circulating pump running
3)
On = Reversing valve set to “Cooling”
Off = Reversing valve set to “Heating”
4)
On = Heat circulating pump running
5)
On = Output of heat generator 2 - off
6)
On = Frost protection request - HP heating
Off = Frost protection request - off
7)
On = Low-pressure controller in working order
8)
Not used
9)
Not used
10) Not used
11) Flashes during operation
12) Flashes in the case of a fault
E-6
Hot water preparation can also be requested even if neither heating and cooling have been requested.
If a request is pending, the heat circulating pump is switched off
by the control system. The cooling operation is interrupted and
the setpoint is raised to the maximum.
The external thermostat determines the hot water setpoint temperature.
Set the temperature to approx. 10 K under the maximum flow
temperature of the heat pump to prevent the high-pressure controller from initiating a switch-off.
When the preparation of hot water is concluded, the system will
continue working in the same function as before the request.
12
10 Maintenance and
Cleaning
11 Faults and Troubleshooting
10.1 Maintenance
This heat pump is a quality product and is designed for troublefree operation. In the event that a fault should occur, you should
be able to correct the problem yourself in most cases.
10.2 Cleaning of Heating Side
The ingress of oxygen into the heating water circuit, in particular
if it contains steel components, may result in the formation of oxidation products (rust). These can enter the heating system via
valves, circulating pumps or plastic tubing. It is therefore important - in particular with respect to the piping of underfloor heating
systems - that the installation be executed in a diffusion-proof
manner.
ATTENTION!
To prevent the accumulation of deposits (e.g. rust) we recommend using
a suitable corrosion protection system.
In the case of severe contamination leading to a reduction in the
performance of the condenser in the heat pump, the system must
be cleaned by a heating technician.
If you cannot correct the fault yourself, please contact your aftersales service technician.
ATTENTION!
Any work on the heat pump may only be performed by authorised and
qualified after-sales service technicians.
ATTENTION!
Disconnect all electrical circuits from the power source prior to opening
the device.
12 Decommissioning/
Disposal
Before removing the heat pump, disconnect it from the power
source and close all valves. Observe all environmentally-relevant
requirements regarding the recovery, recycling and disposal of
materials and components in accordance with all applicable
standards. Particular attention should be paid to the proper disposal of refrigerants and refrigeration oils.
Based on current knowledge, we recommend cleaning with a
5% phosphoric acid solution or, in the case that cleaning needs
to be performed more frequently, with a 5% formic acid solution.
In either case, the cleaning fluid should be at room temperature.
It is recommended that the heat exchanger be cleaned in the direction opposite to the normal flow direction.
To prevent acidic cleaning agents from entering the circuit of the
heating installation we recommend that the flushing device be fitted directly to the supply and return lines of the condenser of the
heat pump.
Thereafter the system must be thoroughly flushed using appropriate neutralising agents in order to prevent any damage caused
by cleaning agent residues that may still be present in the system.
All acids must be used with great care, all relevant regulations of
the employers' liability insurance associations must be adhered
to.
If in doubt, contact the manufacturer of the chemicals!
10.3 Cleaning the Heat Source
System
ATTENTION!
Insert a dirt trap in the heat source inlet of the heat pump to protect the
evaporator against the ingress of impurities.
Clean the dirt trap's filter screen one day after start-up and subsequently at weekly intervals. If no more signs of contamination
are evident, the filter can be removed to reduce pressure drops.
www.dimplex.de
E-7
English
The heat pump is maintenance-free. To prevent faults due to
sediment in the heat exchangers, care must be taken to ensure
that no impurities can enter either the heat source system or the
heating system. In the event that operating malfunctions due to
contamination occur nevertheless, the system should be cleaned
as described below.
13
13 Device Information
Device information for brine-to-water heat pumps (heating only)
1
Type and order code
2
Design
SI 8MR SI 10MR SI 12TR SI 14TR SI 16TR SI 20TR
English
2.1
Model
2.2
Degree of protection according to EN 60 529
Reversible Reversible Reversible Reversible Reversible Reversible
2.3
Installation location
3
Performance data
3.1
Operating temperature limits:
IP20
IP20
IP20
IP20
IP20
Indoors
Indoors
Indoors
Indoors
Indoors
Indoors
Heating water flow
°C
Up to 60
Up to 60
Up to 60
Up to 60
Up to 60
Up to 60
Cooling, flow
°C
+7 to +20
+7 to +20
+7 to +20
+7 to +20
+7 to +20
+7 to +20
Brine (heat source, heating)
°C
-5 to +25
-5 to +25
-5 to +25
-5 to +25
-5 to +25
-5 to +25
Brine (heat sink, cooling)
°C
+5 to +25
+5 to +25
+5 to +25
+5 to +25
+5 to +25
+5 to +25
Monoethyl- Monoethyl- Monoethyl- Monoethyl- Monoethyl- Monoethylene glycol ene glycol ene glycol ene glycol ene glycol ene glycol
Antifreeze
Minimum brine concentration (-13 °C freezing temperature)
3.2
Temperature spread of heating water (flow/return flow) at B0 / W35K
3.3
Heat output / COP
Cooling capacity / COP
25%
25%
25%
25%
25%
25%
10.6
9.9
9.9
9.4
9.6
10.7
at B-5 / W55 1
kW / ---
7.5 / 2.0
9.8 / 2.1
9.8 / 2.1
12.2 / 2.3
14.1 / 2.4
18.7 /2.5
at B0 / W50 1
kW / ---
8.8 / 2.8
11.3 / 2.9
11.3 / 2.9
13.5 / 2.9
16.3 / 3.2
20.4 / 3.1
1
20.0 / 4.2
kW / ---
9.3 / 4.0
11.6 / 4.1
11.6 / 4.1
13.7 / 4.0
16.4 / 4.0
at B20 / W8
kW / ---
9.9 / 4.6
11.4 / 4.6
11.4 / 4.6
14.1 / 5.0
17.3 / 4.9
21.5 / 4.9
at B20 / W18
kW / ---
12.0 / 54
14.1 / 5.3
14.1 / 5.3
17.4 / 5.9
21.5 / 5.9
26.0 / 5.7
at B10 / W8
kW / ---
9.9 / 5.6
11.6 / 5.7
11.6 / 5.7
14.7 / 6.4
18.0 / 6.4
21.9 / 5.9
kW / ---
12.4 / 6.7
14.1 / 6.5
14.1 / 6.5
17.4 / 7.1
21.5 / 7.3
27.7 / 7.1
54
55
56
56
56
56
at B0 / W35
3.4
IP20
at B10 / W18
3.5
Sound power level
dB(A)
3.6
Heating water flow with an internal pressure differential of m³/h / Pa
3.7
Brine throughput with an internal pressure differential
(heat source) of
m³/h / Pa
3.8
Refrigerant; total filling weight
type / kg
4
Dimensions, connections and weight
4.1
Device dimensions without connections 2
H x W x L mm
4.2
Device connections to heating system
Inch
4.3
Device connections to heat source
Inch
kg
4.4
Weight of the transportable unit(s) incl. packing
5
Electrical Connection
5.1
Nominal voltage; fuse protection
5.2
Nominal power consumption 1
5.3
V/A
0.75/ 2,300 1.0 / 4,100 1.0 / 4,100 1.3 / 4,850 1.5 / 4,000 1.6 / 3,400
2.3 /
25,000
3.0 /
24,000
3.0 /
24,000
3.5 /
17,900
3.8 /
18,400
3.5 /
13,900
R407C /
1.3
R407C /
1.5
R407C /
1.4
R407C /
2.1
R407C /
2.4
R407C /
3.2
1220 x 640 1220 x 640 1220 x 640 1220 x 640 1220 x 640 1220 x 640
x 624
x 624
x 624
x 624
x 624
x 624
G 1" a
G 1" a
G 1" a
G 1" a
G 1" a
G 1" a
G 1¼"
external
G 1" a
G 1" a
G 1" a
G 1" a
G 1¼"
external
162
163
164
166
172
237
230 / 20
230 / 25
400 / 16
400 / 16
400 / 16
400 / 16
kW
2.3
2.8
2.8
3.41
4.1
4.8
Starting current with soft starter
A
38
38
26
26
30
30
5.4
Nominal current B0 W35 / cos ϕ
A / ---
12.5 / 0.8
15.2 / 0.8
4.8 / 0.8
6.2 / 0.8
7.4 / 0.8
11.0 / 0,8
6
Complies with the European safety regulations
3
3
3
3
3
3
7
Additional model features
7.1
Water in device protected against freezing 4
No
No
No
No
No
No
7.2
Performance levels
1
1
1
1
1
1
7.3
Controller internal/external
Internal
Internal
Internal
Internal
Internal
Internal
B0 W35
1. This data indicates the size and capacity of the system. For an analysis of the economic and energy efficiency of the system, both the bivalence point and the regulation should
also be taken into consideration. The specified values, e.g. B10 / W55, have the following meaning: Heat source temperature 10 °C and heating water flow temperature 55 °C.
2. Note that additional space is required for pipe connections, operation and maintenance.
3. See CE declaration of conformity
4. The heat circulating pump and the heat pump controller must always be ready for operation.
E-8
Anhang / Appendix / Annexes
1
Maßbild / Dimension drawing / Schéma coté ............................................................................ A-II
2
Diagramme / Diagrams / Diagrammes....................................................................................... A-III
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
Stromlaufpläne / Circuit diagrams / Schémas électriques .....................................................A-XV
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4
Last / Load / Charge SI 8MR - SI 10MR .............................................................................................. A-XV
Steuerung / Control / Commande SI 8MR - SI 10MR......................................................................... A-XVI
Legende / Legend / Légende SI 8MR - SI 10MR............................................................................... A-XVII
Last / Load / Charge SI 12TR - SI 16TR........................................................................................... A-XVIII
Steuerung / Control / Commande SI 12TR - SI 16TR ........................................................................ A-XIX
Legende / Legend / Légende SI 12TR - SI 16TR ................................................................................ A-XX
Last / Load / Charge SI 20TR ............................................................................................................. A-XXI
Steuerung / Control / Commande SI 20TR........................................................................................ A-XXII
Legende / Legend / Légende SI 20TR.............................................................................................. A-XXIII
Hydraulische Prinzipschemen / Hydraulic block diagrams / Schémas hydrauliques ..... A-XXIV
4.1 Heizen und dynamische Kühlung / Heating and dynamic cooling /
Chauffage et refroidissement hydrauliques ......................................................................................A-XXIV
4.2 Heizen und dynamische Kühlung und Warmwasserbereitung /
Heating and dynamic cooling and hot water preparation /
Chauffage et refroidissement hydrauliques et production d’eau chaude...........................................A-XXV
4.3 Legende / Legend / Légende............................................................................................................A-XXVI
5
Konformitätserklärung / Declaration of Conformity / Déclaration de conformité ........... A-XXVII
www.dimplex.de
A-I
Anhang · Appendix · Annexes
3
Heizbetrieb / Heating operation / Mode de chauffage SI 8MR .............................................................. A-III
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 8MR......................................................A-IV
Heizbetrieb / Heating operation / Mode de chauffage SI 10MR .............................................................A-V
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 10MR....................................................A-VI
Heizbetrieb / Heating operation / Mode de chauffage SI 12TR ............................................................A-VII
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 12TR...................................................A-VIII
Heizbetrieb / Heating operation / Mode de chauffage SI 14TR .............................................................A-IX
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 14TR......................................................A-X
Heizbetrieb / Heating operation / Mode de chauffage SI 16TR .............................................................A-XI
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 16TR....................................................A-XII
Heizbetrieb / Heating operation / Mode de chauffage SI 20TR ...........................................................A-XIII
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 20TR.................................................. A-XIV
A-II
FD
DSSUR[
HQY
6,056,75´
6,756,75´
6RXUFHGHFKDOHXU
(QWUpHGDQVOD3$&
$OOHUHDXGHFKDXIIDJH
6RUWLHGHOD3$&
)LOHWDJHH[WpULHXU´
+HDWLQJZDWHUIORZ
+HDWSXPSRXWOHW
´H[WHUQDOWKUHDG
:lUPHTXHOOH
(LQJDQJLQGLH:3
+HDWVRXUFH
+HDWSXPSLQOHW
+HL]XQJVYRUODXI
$XVJDQJDXVGHU:3
´$X‰HQJHZLQGH
5HWRXUHDXGHFKDXIIDJH
(QWUpHGDQVOD3$&
)LOHWDJHH[WpULHXU´
+HDWLQJZDWHUUHWXUQIORZ
+HDWSXPSLQOHW
´H[WHUQDOWKUHDG
+HL]XQJVUFNODXI
(LQJDQJLQGLH:3
´$X‰HQJHZLQGH
(FRXOHPHQWVXUSUHVVLRQ
&LUFXLWGHFKDXIIDJH
7X\DX
2YHUSUHVVXUHRXWOHW
+HDWLQJFLUFXLWV
KRVH
6,056,75´
6,756,75´
6RXUFHGHFKDOHXU
6RUWLHGHOD3$&
+HDWVRXUFH
+HDWSXPSRXWOHW
:lUPHTXHOOH
$XVJDQJDXVGHU:3
(FRXOHPHQWVXUSUHVVLRQ
&LUFXLWHDXJO\FROpH
7X\DX
2YHUSUHVVXUHRXWOHW
%ULQHFLUFXLWV
KRVH
Anhang · Appendix · Annexes
$XVODXIhEHUGUXFN
6ROHNUHLV
6FKODXFK
$XVODXIhEHUGUXFN
+HL]NUHLV
6FKODXFK
1
1 Maßbild / Dimension drawing / Schéma coté
2.1
2 Diagramme / Diagrams / Diagrammes
2.1
Heizbetrieb / Heating operation / Mode de chauffage SI 8MR
+HL]OHLVWXQJLQ>N:@
+HDWLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHFKDXIIDJHHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
+HL]ZDVVHUGXUFKVDW]
+HDWLQJZDWHUIORZUDWH
'pELWG
HDXGHFKDXIIDJH
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
www.dimplex.de
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
A-III
2.2
2.2
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 8MR
.KOOHLVWXQJLQ>N:@
&RROLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHUHIURLGLVVHPHQWHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
:DVVHUGXUFKVDW]
:DWHUIORZUDWH
'pELWG
HDX
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
A-IV
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
2.3
2.3
Heizbetrieb / Heating operation / Mode de chauffage SI 10MR
+HL]OHLVWXQJLQ>N:@
+HDWLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHFKDXIIDJHHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
+HL]ZDVVHUGXUFKVDW]
+HDWLQJZDWHUIORZUDWH
'pELWG
HDXGHFKDXIIDJH
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
www.dimplex.de
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
A-V
2.4
2.4
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 10MR
.KOOHLVWXQJLQ>N:@
&RROLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHUHIURLGLVVHPHQWHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
:DVVHUGXUFKVDW]
:DWHUIORZUDWH
'pELWG
HDX
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
A-VI
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
2.5
2.5
Heizbetrieb / Heating operation / Mode de chauffage SI 12TR
+HL]OHLVWXQJLQ>N:@
+HDWLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHFKDXIIDJHHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
+HL]ZDVVHUGXUFKVDW]
+HDWLQJZDWHUIORZUDWH
'pELWG
HDXGHFKDXIIDJH
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
www.dimplex.de
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
A-VII
2.6
2.6
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 12TR
.KOOHLVWXQJLQ>N:@
&RROLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHUHIURLGLVVHPHQWHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
Anhang · Appendix · Annexes
:DVVHUGXUFKVDW]
:DWHUIORZUDWH
'pELWG
HDX
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
A-VIII
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
2.7
2.7
Heizbetrieb / Heating operation / Mode de chauffage SI 14TR
+HL]OHLVWXQJLQ>N:@
+HDWLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHFKDXIIDJHHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
+HL]ZDVVHUGXUFKVDW]
+HDWLQJZDWHUIORZUDWH
'pELWG
HDXGHFKDXIIDJH
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
www.dimplex.de
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
A-IX
2.8
2.8
Kühlbetrieb / Cooling operation / Mode de refroidissement SI 14TR
.KOOHLVWXQJLQ>N:@
&RROLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHUHIURLGLVVHPHQWHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
Anhang · Appendix · Annexes
:DVVHUGXUFKVDW]
:DWHUIORZUDWH
'pELWG
HDX
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
A-X
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
2.9
2.9
Heizbetrieb / Heating operation / Mode de chauffage SI 16TR
+HL]OHLVWXQJLQ>N:@
+HDWLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHFKDXIIDJHHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
+HL]ZDVVHUGXUFKVDW]
+HDWLQJZDWHUIORZUDWH
'pELWG
HDXGHFKDXIIDJH
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
P K
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
www.dimplex.de
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
A-XI
2.10
2.10 Kühlbetrieb / Cooling operation / Mode de refroidissement SI 16TR
.KOOHLVWXQJLQ>N:@
&RROLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHUHIURLGLVVHPHQWHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
Anhang · Appendix · Annexes
:DVVHUGXUFKVDW]
:DWHUIORZUDWH
'pELWG
HDX
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
A-XII
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
2.11
2.11 Heizbetrieb / Heating operation / Mode de chauffage SI 20TR
+HL]OHLVWXQJLQ>N:@
+HDWLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHFKDXIIDJHHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
+HL]ZDVVHUGXUFKVDW]
+HDWLQJZDWHUIORZUDWH
'pELWG
HDXGHFKDXIIDJH
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
P K
Anhang · Appendix · Annexes
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
www.dimplex.de
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
A-XIII
2.12
2.12 Kühlbetrieb / Cooling operation / Mode de refroidissement SI 20TR
.KOOHLVWXQJLQ>N:@
&RROLQJFDSDFLW\LQ>N:@
3XLVVDQFHGHUHIURLGLVVHPHQWHQ>N:@
:DVVHUDXVWULWWVWHPSHUDWXULQ>ƒ&@
:DWHURXWOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHGHVRUWLHGHO
HDXHQ>ƒ&@
%HGLQJXQJHQÂ&RQGLWLRQVÂ&RQGLWLRQV
Anhang · Appendix · Annexes
:DVVHUGXUFKVDW]
:DWHUIORZUDWH
'pELWG
HDX
PK
6ROHGXUFKVDW]
%ULQHIORZUDWH
'pELWG
HDXJO\FROpH
PK
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@Â%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@Â7HPSpUDWXUHG
HQWUpHG
HDXJO\FROpHHQ>ƒ&@
/HLVWXQJVDXIQDKPHLQFO3XPSHQOHLVWXQJVDQWHLO
3RZHUFRQVXPSWLRQLQFOSRZHULQSXWWRSXPS
&RQVRPPDWLRQGHSXLVVDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
9HUGDPSHU
(YDSRUDWRU
(YDSRUDWHXU
/HLVWXQJV]DKOLQFO3XPSHQOHLVWXQJVDQWHLO
&RHIILFLHQWRISHUIRUPDQFHLQFOSRZHULQSXWWRSXPS
&RHIILFLHQWGHSHUIRUPDQFH\FRPSULVSDUWGHFRQVRPPDWLRQGHODSRPSH
9HUIOVVLJHU
&RQGHQVHU
&RQGHQVHXU
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
A-XIV
'UXFNYHUOXVWLQ>3D@
3UHVVXUHORVVLQ>3D@
3HUWHGHSUHVVLRQHQ>3D@
6ROHGXUFKIOXVVLQ>PK@
%ULQHIORZUDWHLQ>PK@
'pELWG
HDXJO\FROpHHQ>PK@
6ROHHLQWULWWVWHPSHUDWXULQ>ƒ&@
%ULQHLQOHWWHPSHUDWXUHLQ>ƒ&@
7HPSpUDWXUHG
HQWUpHG¶HDXJO\FROpHHQ>ƒ&@
+HL]ZDVVHUGXUFKIOXVVLQ>PK@
+HDWLQJZDWHUIORZUDWHLQ>PK@
'pELWG
HDXGHFKDXIIDJHHQ>PK@
3.1
3 Stromlaufpläne / Circuit diagrams / Schémas
électriques
Last / Load / Charge SI 8MR - SI 10MR
Anhang · Appendix · Annexes
3.1
www.dimplex.de
A-XV
3.2
3.2
Anhang · Appendix · Annexes
A-XVI
Steuerung / Control / Commande SI 8MR - SI 10MR
3.3
Legende / Legend / Légende SI 8MR - SI 10MR
A1
Drahtbrücke muss, bei externer Ansteuerung oder
Verwendung eines Taupunktwächters, entfernt
werden
Wire jumper, must be removed if external control or
a dew point monitor are used
Retirer le cavalier à fil en cas de commande
externe ou d'utilisation d’un contrôleur du point de
condensation
B3
Thermostat Warmwasser
Hot water thermostat
Thermostat eau chaude
C1
Betriebskondensator
Operating condenser
Condensateur de service
F1
F4
F5
Steuersicherung
Pressostat Hochdruck
Pressostat Niederdruck
Control fuse
High-pressure controller
Low-pressure controller
Sécurité de commande
Pressostat haute pression
Pressostat basse pression
H1
Leuchte Betriebsbereit
Indicator lamp, ready for operation
Affichage prêt à fonctionner
K24
K25
Relais-Warmwasseranforderung
Startrelais für N7
Relay, request for hot water
Start relay for N7
Relais demande d’eau chaude
Relais départ sur N7
M1
M11
M13
Verdichter
Primärumwälzpumpe (Sole)
Heizungsumwälzpumpe
Compressor
Primary circulating pump (brine)
Heat circulating pump
Compresseur
Circulateur primaire (eau glycolée)
Circulateur de chauffage
N5*
N7
N12
N13*
Taupunktwächter
Sanftanlasser
Steuerungsplatine
Schaltgruppe Warmwasser
Dew point monitor
Soft starter
Control PCB
Switching assembly, hot water
Contrôleur du point de condensation
Démarreur progressif
Platine de commande
Groupe commutateur eau chaude
R2
R6
R7
R8
R10*
R11
R14
Rücklauffühler
Eingefrierschutzfühler (Sole)
Kodierwiderstand
Frostschutzfühler-Kühlbetrieb (Wasser)
Feuchtefühler
Vorlauffühler
Sollwert Potentiometer
Return flow sensor
Flow temperature limit sensor (brine)
Coding resistor
Flow sensor for cooling operation (water)
Humidity sensor
Flow sensor
Setpoint potentiometer
Sonde de retour
Sonde antigel (eau glycolée)
Résistance de codage
Capteur protection antigel mode refroidiss. (eau)
Sonde d’humidité
Sonde circuit départ
Valeur nominale potentiomètre
S1
Steuerschalter WP-EIN/AUS
Control switch HP ON/OFF
S2
Umschalter HEIZEN/KÜHLEN (Kontakt offen = Heizen)
Changeover switch HEATING/COOLING (contact
open = heating)
Commutateur de commande PAC-MARCHE/
ARRET
Commutateur CHAUFFAGE/REFROIDISSEMENT
(Contact ouvert = chauffage)
X1
X2
X3
Klemmenleiste Netz L/N/PE-230VAC-50Hz/
externe Komponenten
Klemmenleiste interne Verdrahtung
Klemmenleiste Verdichter
Terminal strip for power supply L/N/PE-230 V AC50Hz/external components
Terminal strip for internal wiring
Terminal strip for compressor
Bornier réseau L/N/PE-230VAC-50Hz/composants
externes
Bornier câblage interne
Bornier compresseur
Y1
4-Wege-Umschaltventil Heizen/Kühlen
Four-way reversing valve, heating/cooling
Y5*
3-Wege-Umschaltventil zur Brauchwarmwasserbereitung
Three-way reversing valve for domestic hot water
preparation
Soupape de commutation 4 voies chauffage/
refroidissement
Soupape de commutation 3 voies pour production
ECS
*
Bauteile sind extern beizustellen
Components which must be supplied from external
sources
www.dimplex.de
Pièces à fournir par le client
A-XVII
Anhang · Appendix · Annexes
3.3
3.4
3.4
Last / Load / Charge SI 12TR - SI 16TR
1HW]Â0DLQVÂ5pVHDX
Anhang · Appendix · Annexes
A-XVIII
3.5
Steuerung / Control / Commande SI 12TR - SI 16TR
Anhang · Appendix · Annexes
3.5
www.dimplex.de
A-XIX
3.6
3.6
Legende / Legend / Légende SI 12TR - SI 16TR
Anhang · Appendix · Annexes
A1
Drahtbrücke muss, bei externer Ansteuerung oder
Verwendung eines Taupunktwächters, entfernt
werden
Wire jumper, must be removed if external control or
a dew point monitor are used
Retirer le cavalier à fil en cas de commande
externe ou d'utilisation d’un contrôleur du point de
condensation
B3
Thermostat Warmwasser
Hot water thermostat
Thermostat eau chaude
F1
F4
F5
Steuersicherung
Pressostat Hochdruck
Pressostat Niederdruck
Control fuse
High-pressure controller
Low-pressure controller
Sécurité de commande
Pressostat haute pression
Pressostat basse pression
H1
Leuchte Betriebsbereit
Indicator lamp, ready for operation
Affichage prêt à fonctionner
K1
K24
Schütz Verdichter
Relais-Warmwasseranforderung
Contactor for compressor
Relay, request for hot water
Contacteur compresseur
Relais demande d’eau chaude
M1
M11
M13
Verdichter
Primärumwälzpumpe (Sole)
Heizungsumwälzpumpe
Compressor
Primary circulating pump (brine)
Heat circulating pump
Compresseur
Circulateur primaire (eau glycolée)
Circulateur de chauffage
N5*
N7
N12
N13*
Taupunktwächter
Sanftanlasser
Steuerungsplatine
Schaltgruppe Warmwasser
Dew point monitor
Soft starter
Control PCB
Switching assembly, hot water
Contrôleur du point de condensation
Démarreur progressif
Platine de commande
Groupe commutateur eau chaude
R2
R6
R7
R8
R10*
R11
R14
Rücklauffühler
Eingefrierschutzfühler (Sole)
Kodierwiderstand
Frostschutzfühler-Kühlbetrieb (Wasser)
Feuchtefühler
Vorlauffühler
Sollwert Potentiometer
Return flow sensor
Flow temperature limit sensor (brine)
Coding resistor
Flow sensor for cooling operation (water)
Humidity sensor
Flow sensor
Setpoint potentiometer
Sonde de retour
Sonde antigel (eau glycolée)
Résistance de codage
Capteur protection antigel mode refroidiss. (eau)
Sonde d’humidité
Sonde circuit départ
Valeur nominale potentiomètre
S1
Steuerschalter WP-EIN/AUS
Control switch HP ON/OFF
S2
Umschalter HEIZEN/KÜHLEN
Changeover switch HEATING/COOLING
Commutateur de commande PAC-MARCHE/
ARRET
Commutateur CHAUFFAGE/REFROIDISSEMENT
X1
X2
Klemmenleiste Netz L/N/PE-230VAC-50Hz/
externe Komponenten
Klemmenleiste interne Verdrahtung
Terminal strip for power supply L/N/PE-230 V AC50Hz/external components
Terminal strip for internal wiring
Bornier réseau L/N/PE-230VAC-50Hz/composants
externes
Bornier câblage interne
Y1
4-Wege-Umschaltventil Heizen/Kühlen
Four-way reversing valve, heating/cooling
Y5*
3-Wege-Umschaltventil zur Brauchwarmwasserbereitung
Three-way reversing valve for domestic hot water
preparation
Soupape de commutation 4 voies chauffage/
refroidissement
Soupape de commutation 3 voies pour production
ECS
*
Bauteile sind extern beizustellen
Components which must be supplied from external
sources
A-XX
Pièces à fournir par le client
3.7
Last / Load / Charge SI 20TR
1HW]Â0DLQVÂ5pVHDX
Anhang · Appendix · Annexes
3.7
www.dimplex.de
A-XXI
3.8
3.8
Anhang · Appendix · Annexes
A-XXII
Steuerung / Control / Commande SI 20TR
3.9
Legende / Legend / Légende SI 20TR
A1
Drahtbrücke muss, bei externer Ansteuerung oder
Verwendung eines Taupunktwächters, entfernt
werden
Wire jumper, must be removed if external control or
a dew point monitor are used
Retirer le cavalier à fil en cas de commande
externe ou d'utilisation d’un contrôleur du point de
condensation
B3*
Thermostat Warmwasser
Hot water thermostat
Thermostat eau chaude
F1
F4
F5
Steuersicherung
Pressostat Hochdruck
Pressostat Niederdruck
Control fuse
High-pressure controller
Low-pressure controller
Sécurité de commande
Pressostat haute pression
Pressostat basse pression
H1
Leuchte Betriebsbereit
Indicator lamp, ready for operation
Affichage prêt à fonctionner
K1
K1.1
K24
Schütz Verdichter
Schütz Anlaufstrombegrenzung von M1
Relais-Warmwasseranforderung
Contactor for compressor
Contactor for starting current limiter from M1
Relay, request for hot water
Contacteur compresseur
Contacteur courant limite de démarrage de M1
Relais demande d’eau chaude
M1
M11
M13
Verdichter
Primärumwälzpumpe (Sole)
Heizungsumwälzpumpe
Compressor
Primary circulating pump (brine)
Heat circulating pump
Compresseur
Circulateur primaire (eau glycolée)
Circulateur de chauffage
N5*
N7
N12
N13*
Taupunktwächter
Sanftanlasser
Steuerungsplatine
Schaltgruppe Warmwasser
Dew point monitor
Soft starter
Control PCB
Switching assembly, hot water
Contrôleur du point de condensation
Démarreur progressif
Platine de commande
Groupe commutateur eau chaude
R2
R6
R7
R8
R10*
R11
R14
Rücklauffühler
Eingefrierschutzfühler (Sole)
Kodierwiderstand
Frostschutzfühler-Kühlbetrieb (Wasser)
Feuchtefühler
Vorlauffühler
Sollwert Potentiometer
Return flow sensor
Flow temperature limit sensor (brine)
Coding resistor
Flow sensor for cooling operation (water)
Humidity sensor
Flow sensor
Setpoint potentiometer
Sonde de retour
Sonde antigel (eau glycolée)
Résistance de codage
Capteur protection antigel mode refroidiss. (eau)
Sonde d’humidité
Sonde circuit départ
Valeur nominale potentiomètre
S1
Steuerschalter WP-EIN/AUS
Control switch HP ON/OFF
S2
Umschalter HEIZEN/KÜHLEN
Changeover switch HEATING/COOLING
Commutateur de commande PAC-MARCHE/
ARRET
Commutateur CHAUFFAGE/REFROIDISSEMENT
X1
X2
Klemmenleiste Netz L/N/PE-230VAC-50Hz/
externe Komponenten
Klemmenleiste interne Verdrahtung
Terminal strip for power supply L/N/PE-230 V AC50Hz/external components
Terminal strip for internal wiring
Bornier réseau L/N/PE-230VAC-50Hz/composants
externes
Bornier câblage interne
Y1
4-Wege-Umschaltventil Heizen/Kühlen
Four-way reversing valve, heating/cooling
Y5*
3-Wege-Umschaltventil zur Brauchwarmwasserbereitung
Three-way reversing valve for domestic hot water
preparation
Soupape de commutation 4 voies chauffage/
refroidissement
Soupape de commutation 3 voies pour production
ECS
*
Bauteile sind extern beizustellen
Components which must be supplied from external
sources
www.dimplex.de
Pièces à fournir par le client
A-XXIII
Anhang · Appendix · Annexes
3.9
4
4 Hydraulische Prinzipschemen / Hydraulic block
diagrams / Schémas hydrauliques
4.1
Anhang · Appendix · Annexes
A-XXIV
Heizen und dynamische Kühlung / Heating and dynamic cooling /
Chauffage et refroidissement hydrauliques
4.2
Heizen und dynamische Kühlung und Warmwasserbereitung /
Heating and dynamic cooling and hot water preparation /
Chauffage et refroidissement hydrauliques et production d’eau chaude
Anhang · Appendix · Annexes
4.2
www.dimplex.de
A-XXV
4.3
4.3
Legende / Legend / Légende
Anhang · Appendix · Annexes
Absperrventil
Shutoff valve
Robinet d’arrêt
Überstromventil
Overflow valve
Soupape de trop-plein
Sicherheitsventilkombination
Safety valve combination
Groupe de valves de sécurité
Umwälzpumpe
Circulating pump
Circulateur
Ausdehnungsgefäß
Expansion vessel
Vase d´expansion
Raumtemperaturgesteuertes Ventil
Room temperature-controlled valve
Valve commandée par température
Drei-Wege-Ventil
Three-way valve
Soupape 3 voies
Wärmeverbraucher
Heat consumer
Consommateur de chaleur
Temperaturfühler
Temperature sensor
Sonde de température
Flexibler Anschlussschlauch
Flexible connection hose
Tuyau de raccord flexible
Sole/Wasser-Wärmepumpe
Brine-to-water heat pump
Pompe à chaleur eau glycolée/eau
Pufferspeicher
Buffer tank
Réservoir tampon
Warmwasserspeicher
Hot water cylinder
Ballon d’eau chaude
Erdwärmesonden
Borehole heat exchangers
Sondes géothermiques
Überdruck Heizung
Overpressure of the heating system
Surpression chauffage
Überdruck Sole
Overpressure of the brine
Surpression eau glycolée
EV
Elektroverteilung
Electrical distribution system
Distributeur courant électrique
KW
Kaltwasser
Cold water
Eau froide
WW
Warmwasser
Hot water
Eau chaude
E10.1
Elektroheizstab
Electric heating element
Cartouche chauffante
B3
Warmwasserthermostat
Hot water thermostat
Thermostat d’eau chaude
M11
Primärumwälzpumpe
Primary circulating pump
Circulateur primaire
M13
Heizungsumwälzpumpe
Heat circulating pump
Circulateur de chauffage
R2
Rücklauffühler
Return flow sensor
Sonde de retour
R6
Eingefrierschutz Sole
Flow temperature limit sensor, brine
Sonde antigel eau glycolée
R11
Vorlauffühler
Flow sensor
Sonde circuit départ
Y5
Drei-Wege-Ventil
Three-way valve
Soupape 3 voies
A-XXVI
5
Anhang · Appendix · Annexes
5 Konformitätserklärung / Declaration of Conformity /
Déclaration de conformité
www.dimplex.de
A-XXVII
Glen Dimplex Deutschland GmbH
Geschäftsbereich Dimplex
Am Goldenen Feld 18
D-95326 Kulmbach
Irrtümer und Änderungen vorbehalten.
Subject to alterations and errors.
Sous réserve d’erreurs et modifications.
+49 (0) 9221 709 565
www.dimplex.de
Download PDF