Zenith | DPDP60W | Owner`s manual | Zenith DPDP60W Owner`s manual

Model number : DPDP60W
Serial number :
PLASMA DISPLAY PANEL
Please read this owner’s manual carefully before
operating the Monitor.
Retain it for future reference.
Record model number and serial number of the
Monitor.
See the label attached on the back of the Monitor
and quote this information to your dealer when you
require service.
DPDP60W
OWNER’S MANUAL
P/NO : 3828VA0277B
(NP00KA)
ON/OFF
INPUT SELECT
VOLUME
FCC NOTICE
• DPDP60W : A Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to raido communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING
This is Class B product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
ON/OFF
INPUT SELECT
VOLUME
Table of Contents
First step
WARNINGS ..............................................................4
SAFETY INSTRUCTIONS........................................5
Composition
Front Panel Controls ................................................8
Connection Panel Overview .....................................9
Remote Control Key Functions/Accessories ..........10
Installation of the monitor .......................................12
Connection
VCR Setup..............................................................14
Cable TV Setup ......................................................15
External AV Source Setup ......................................16
DVD Setup..............................................................17
DTV Setup ..............................................................18
PC Setup ................................................................19
PC Computer Mode Feature Check.......................21
PC Computer Mode Adjustments ...........................22
PIP function ............................................................25
Twin picture function...............................................28
Using the remote control ........................................30
Basic function
Turning on the Monitor ...........................................31
Selecting language for the menus..........................32
Checking features...................................................33
Time setting
Setting sleep time...................................................34
Picture & Sound
Auto picture control ................................................35
Adjusting picture appearance.................................36
DRP (Digital Reality Picture) ..................................37
Selecting screen item .............................................38
Adjusting sound appearance..................................39
Auto sound control .................................................40
AVL (Auto volume leveler) ......................................41
Keep this manual
with Monitor for
future easy reference)
Special function
Using Still function ..................................................42
Adjusting OSD Transparency .................................43
Setting picture format .............................................44
Others
Maintenance ...........................................................45
Troubleshooting check list ......................................46
Product specifications.............................................47
WARNINGS
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
CAUTION:
Do not attempt to modify this product in any way without written authorization from Zenith Electronics
Corporation. Unauthorized modification could void the user’s authority to operate this product.
The responsible party for this device compliance is:
Zenith Electronics Corporation
201 James Record Road
Huntsville, AL 35824, USA
1-877-993-6484
4
First step
SAFETY INSTRUCTIONS
Composition
Important safeguards for you and your new product
8. Transporting Product
The safety and operating instructions should
be retained for future reference.
A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
2. Follow Instructions
4. Heed Warnings
Time setting
3. Retain Instructions
All the safety and operating instructions
should be read before the product is operated.
Basic function
All operating and use instructions should be
followed.
slide or fall, causing serious injury to a child
or adult, and serious damage to the product.
Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer,
or sold with the product. Any mounting of
the product should follow the manufacturer’s
instructions, and should use a mounting
accessory recommended by the manufacturer.
1. Read Instructions
Connection
Your product has been manufactured and tested with your safety in mind. However, improper
use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards
that have been built into your new product, please read and observe the following safety
points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this booklet can help you get many years of
enjoyment and safe operation that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the
Canadian Standards Association.
Picture & Sound
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for
cleaning.
Do not use this product near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories Carts and Stands
Do not use attachments not recommended
by the product manufacturer as they may
cause hazards.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it
from overheating, and these openings must
not be blocked or covered.
Others
Do not place this product on a slippery or
tilted surface, or on an unstable cart, stand,
tripod, bracket, or table. The product may
9. Attachments
Special function
6. Water and Moisture
PORTABLE CART WARNING
(Continued on next page)
5
SAFETY INSTRUCTIONS
(Continued from previous page)
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface. This product should
not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
11. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply to your home, consult your
product dealer or local power company. For
products intended to operate from battery
power, or other sources, refer to the operating instructions.
12. Power-Cord Polarization
This product is equipped with a polarized
alternating-current line plug (a plug having
one blade wider than the other). This plug
will fit into the power outlet only one way.
This is a safety feature. If you are unable to
insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
13. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords at
plugs, convenience receptacles, and the
point where they exit from the product.
14. Outdoor Antenna Grounding
If an outside antenna or cable system is
connected to the product, be sure the
antenna or cable system is grounded so as
to provide some protection against voltage
surges and built-up static charges. Article
810 of the National Electrical Code (U.S.A.),
ANSI/ NFPA 70 provides information with
regard to proper grounding of the mast and
6
supporting structure, grounding of the leadin wire to an antenna discharge unit, size of
grounding conductors, location of antennadischarge unit, connection to grounding
electrodes, and requirements for the
grounding electrode.
Example of Grounding According to National
Electrical Code Instructions
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
NEC - National Electrical Code
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
15. Lightning
For added protection for this product
(receiver) during a lightning storm, or when
it is left unattended and unused for long
periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system. This will prevent damage to the product
due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be
located in the vicinity of overhead power
lines or other electric light or power circuits,
or where it can fall into such power lines or
circuits. When installing an outside antenna
system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension
cords as this can result in a risk of fire or
electric shock.
18. Object and Liquid Entry
Never push objects of any kind into this
First step
19. Servicing
20. Damage Requiring Service
The product should be mounted to a wall or
ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and
serious damage to the product.
24. Heat
The product should be situated away from
heat sources such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
Time setting
Picture & Sound
Special function
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have
fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the product to its
normal operation.
e. If the product has been dropped or the
cabinet has been damaged.
f. If the product exhibits a distinct change
in performance.
23. Wall or Ceiling Mounting
Basic function
Unplug this product from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.
Connection
Do not attempt to service this product yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
22. Safety Check
Composition
product through openings as they may
touch dangerous voltage points or short-out
parts that could result in a fire or electric
shock. Never spill liquid of any kind on the
product.
21. Replacement Parts
Others
When replacement parts are required, be
sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as
the original part. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
7
Front Panel Controls
<Front Panel>
ON/OFF
ON/OFF
INPUT SELECT
VOLUME
Main power button
Power standby indicator
Illuminates red in standby
Illuminates green when the
Monitor is switched on
INPUT
SELECT
VOLUME
INPUT SELECT button
Sub power button
VOLUME (F,G) buttons
Remote control sensor
8
First step
Connection Panel Overview
Composition
<Back Panel>
Connection
Basic function
R AUDIO L (MONO) VIDEO
AV INPUT
Y
PB
PR
PR
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER (8Ω)
AC INPUT
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER 8Ω
AC INPUT
Special function
AV INPUT /
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT) sockets
AUDIO INPUT
Picture & Sound
(MONO)VIDEO
AV INPUT
PB
Time setting
R AUDIO L
Y
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
EXTERNAL
SPEAKER (8Ω)
knobs
RGB-PC INPUT (VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT (480p/720p/1080i) /
AUDIO INPUT sockets
Others
9
Remote Control Key Functions/Accessories
- When using the remote control aim it at the remote control sensor on the Monitor.
power on button
sleep button
(Refer to p.34)
power on
system off
sleep
mute
mute button
switches the sound on or off.
2
1
number buttons
3
5
4
6
8
7
9
video/pc
menu
0
video/pc button
up
vol
enter
vol
down
pip button
(Refer to p.25)
pip
twin picture
input select
position
input select button
(Refer to p.26, 29)
ratio button(Refer to p.44)
When pressing this button,
it’s displayed ARC on screen.
apc button
(Refer to p.35)
10
ratio
apc
freeze
easy sound
First step
Composition
Connection
INPUT SELECT button on the
remote control
system off button
Each press of this button changes
the mode as below.
No function
VIDEO
COMPONENT
Basic function
RGB
menu button
Time setting
enter button
up/down buttons
vol buttons
Picture & Sound
twin picture button(Refer to p.28)
When pressing this button,
it’s displayed DW on screen.
position button
(Refer to p.26)
Special function
freeze button
(Refer to p.42)
easy sound button(Refer to p.40)
When pressing this button,
it’s displayed DASP on screen.
Accessories
power on
system off
sleep
mute
2
1
3
5
4
6
8
7
9
video/pc
menu
0
enter
Others
up
vol
vol
down
Monitor
AS mark
D-sub 15 pin cable
Power cord
Owner’s Manual
1.5V
1.5V
pip
twin picture
input select
position
ratio
apc
freeze
easy sound
Alkaline batteries Remote control
11
Installation of the Monitor
- Use this product at the place lower than the altitude of 6562 feet (2000m) to get the
best quality of picture and sound.
,,,,,,
,,,,,,
,,,,,,
,,,,,,
- Your DPDP60W (Monitor) can be installed on a wall as shown below, or on a desktop
pedestal as shown on the next page.
Wall Mount Installation
• The monitor can be installed on the wall as shown above.
(For further information, refer to the optional ‘(Tilt) wall mounting bracket
Installation and Setup Guide’.)
Tips
• To install this monitor in safety, it must install in a place where is provided a proper
ventilation.
a.
3.94inch
(In case of wall mounting type)
1.18inch
3.94inch
3.94inch
3.94inch
12
First step
Composition
Desktop Pedestal Installation
Connection
Basic function
Time setting
INPUT SELECT
ON/OFF
VOLUME
Picture & Sound
• The Monitor can be installed on the desk as shown above.
(For further information, refer to the optional ‘Desktop stand Installation and Setup Guide’.)
Special function
b.
(In case of desktop type)
3.94inch
Others
3.94inch
1.18inch
3.94inch
2.36inch
13
VCR Setup
- As shown below, when connecting the Monitor to a VCR, match the colors of AV input
jacks on the Monitor with the output jacks on the VCR: Video = yellow, Audio (Left) =
white, Audio (Right) = red.
- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO)
input of the Plasma Monitor.
- When connecting a S-VIDEO VCR to the S-VIDEO socket, the picture quality will be further
improved.
- If 4:3picture format or still word such as watching VCR or CH label is on the screen for a
long time, that fixed image may remain visible.
R AUDIO L (MONO) VIDEO
AV INPUT
R AUDIO L
Y
(MONO)VIDEO
AV INPUT
PB
Y
PB
PR
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
PR
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER (8Ω)
AC INPUT
(+) R ( )
R AUDIO L
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER(8Ω)
AC INPUT
<Back panel of the Monitor>
S-VIDEO
OUT
(R) AUDIO (L)
To watch VCR
VIDEO
IN
<Back panel of VCR>
video/pc
1
2
Press video/pc button on the remote control to select VIDEO.
Insert a video tape into the VCR and press
the PLAY button on the VCR.See VCR
owner’s manual.
Tips
• To prevent picture noise, keep a appropriate distance between VCR and monitor.
14
First step
Cable TV Setup
- After subscribing to a cable TV service from a local provider and installing a converter
you can watch cable TV programming.
Composition
AV INPUT
Y
(MONO)VIDEO
AV INPUT
PB
PB
PR
PR
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER (8Ω)
AC INPUT
(+) R ( )
R AUDIO L
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
Basic function
R AUDIO L
Y
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
Connection
R AUDIO L (MONO) VIDEO
( ) L (+)
EXTERNAL SPEAKER(8Ω)
AC INPUT
(R) AUDIO (L)
Time setting
<Back panel of the Monitor>
<Cable box>
VIDEO
TV
RF
Picture & Sound
VCR
Cable
To watch cable TV
Special function
1
2
Press video/pc button on the remote control to select VIDEO.
video/pc
Select cable provided channels using the
cable box.
Others
Tips
• For further information reguarding cable TV, contact the local cable
TV service provider(s).
15
External AV Source Setup
- As shown below, when connecting the Monitor to an external source, match the colors of AV
input jacks on the Monitor with the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.
R AUDIO L (MONO) VIDEO
AV INPUT
R AUDIO L
(MONO)VIDEO
AV INPUT
Y
PB
Y
PB
PR
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
PR
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER (8Ω)
AC INPUT
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER(8Ω)
AC INPUT
< Back panel of the Monitor>
Camcorder
R
AUDIO
L
VIDEO
Video game set
DDR
To watch external AV source
1
2
16
Press video/pc button on the remote control to select VIDEO.
Operate the corresponding external equipment. See external equipment operating
guide.
video/pc
First step
DVD Setup
Composition
How to connect a DVD (digital video disk player)
• Connect DVD video inputs to Y, PB, PR of COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT) and audio inputs to Audio sockets of AV INPUT.
Connection
R AUDIO L (MONO) VIDEO
AV INPUT
Y
PB
PR
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER (8Ω)
AC INPUT
Basic function
(MONO)VIDEO
AV INPUT
Y
PB
PR
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
Time setting
R AUDIO L
( ) L (+)
EXTERNAL SPEAKER(8Ω)
AC INPUT
< Back panel of the Monitor>
Picture & Sound
(R) AUDIO (L)
B
R
How to use
Component ports of the
Monitor
Video output ports
of DVD player
PR
Y
PB
Y
Y
Y
Y
Pr
Pb
B-Y R-Y
Cb Cr
PB PR
17
Others
• Turn on the DVD player, and insert a DVD.
• Press video/pc button on the remote control to select
COMPONENT. Use DVD to play DVD, see DVD owner’s
manual.
• Component Input ports
Connect DVD player jacks to Monitor
Component input jacks as indicated below.
Special function
< Back panel of a DVD player>
DTV Setup
- To watch digitally broadcast programs, purchase/connect a digital SET-TOP BOX.
- If the DTV signal is input to the Monitor, you can adjust the picture size.
- You can select only the 16:9 picture format in DTV 720p/1080i mode.
How to connect a user-supplied Digital Set-top Box
• Connect DTV video inputs to Y, PB, PR of COMPONENT (480i/480p/720p/1080i) (DVD/DTV
INPUT) or RGB-PC INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT(480p/720p/1080i)
socket and connect DTV audio inputs to Audio sockets of AV INPUT.
R AUDIO L (MONO) VIDEO
AV INPUT
R AUDIO L
(MONO)VIDEO
AV INPUT
Y
Y
PB
PR
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
PR
PB
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER (8Ω)
AC INPUT
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
AUDIO INPUT
( ) L (+)
EXTERNAL SPEAKER(8Ω)
S-VIDEO
AC INPUT
< Back panel of the Monitor>
or
(R) AUDIO (L)
Y
PB
PR
(R) AUDIO (L)
DTV OUTPUT
< Back panel of a digital SET-TOP BOX>
How to use
• Turn on the digital SET-TOP BOX.
(Refer to the owner’s manual for the digital SET-TOP BOX.)
• Press video/pc button on the remote control to select COMPONENT or RGB.
18
First step
PC Setup
- See your computer’s image on the Monitor.
(MONO) VIDEO
AV INPUT
(MONO)VIDEO
AV INPUT
Y
PB
PR
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
PB
PR
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
( ) L (+)
EXTERNAL SPEAKER (8Ω)
AC INPUT
(+) R ( )
R AUDIO L
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
AUDIO INPUT
S-VIDEO
Time setting
R AUDIO L
Y
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
Basic function
R AUDIO L
( ) L (+)
EXTERNAL SPEAKER(8Ω)
AC INPUT
Picture & Sound
< Back panel of the Monitor>
<On the remote control>
• Press POWER button on the PC and press ON/OFF button
on the Monitor. After this press
button on the Monitor or
press power on button on the remote control.
• Press video/pc button on the remote control to select
RGB.
• Set the resolution of PC under SXGA (1280x1024). (Refer
to page 20.)
19
Others
Tips
• To avoid burning an image on the Monitor screen, don’t have a still picture on the screen
for a long period time.
Special function
How to use
video/pc
Connection
Make the connections shown in the illustration below
• Set the computer video output to UXGA; for the best picture quality. (If the video output of the
PC is not compatible with the Monitor, no picture will appear on the Monitor. See page 20.)
• As shown below, connect the video output port of the PC to the Monitor RGB-PC
INPUT(VGA/SVGA/CGA/SXGA) RGB-DTV INPUT(480p/720p/1080i).
• Connect the audio out from the PC to the Audio jacks on the Monitor. (Audio cables not included
with the Monitor)
• If available, adjust PC sound to your preference.
Composition
How to connect
Monitor Image Display Specifications
Resolution
640x350
720x400
640x480
800x600
832x624
1024x768
1152x864
1152x870
1280x960
1280x1024
20
Horizontal
Vertical
Frequency (KHz) Frequency (Hz)
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
45.913
53.011
64.062
35.156
37.879
48.077
46.875
53.674
56.000
64.016
49.725
48.363
56.476
60.023
68.677
54.348
63.995
67.500
77.487
68.681
60.000
75.000
63.981
79.976
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
90.03
100.04
120.00
56.25
60.31
72.18
75.00
85.06
90.00
100.00
74.55
60.00
70.06
75.02
84.99
60.05
70.01
75.00
85.05
75.06
60.00
75.00
60.02
75.02
First step
PC Computer Mode Feature Check
- Select RGB first, see page 11.
2
Press the up/down button to select menus.
Connection
1
Press the menu button to show menus on screen.
Composition
menu
• Each press will cycle through the different menus as shown below.
up
PICTURE
down
D
MOVE
E
GNEXT
G
Basic function
APC
DRP
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
G
100
50
50
0
50
G
G
G
G
G
AEXIT
<Picture menu>
Time setting
SOUND
DASP
AVL
TREBLE
BASS
BALANCE
GNEXT
G
G
G
G
Picture & Sound
D
MOVE
E
G
50
50
0
AEXIT
<Sound menu>
SPECIAL
D
MOVE
E
GNEXT
G
G
Special function
LANGUAGE
ARC
SCREEN
TRANSPARENCY
PIP/DW
G
G
G
AEXIT
<Special menu>
vol
vol
down
3
Press the vol ( G ) button and then press the
up/down or vol button to select a feature you want
to use.
Others
up
• Press the enter button to remove menus.
21
PC Computer Mode Adjustments
Auto adjustment
- The position and trembling of picture is automatically adjusted.
READY
Press the menu button and then press the up/down button
to select SPECIAL menu.
Press the vol ( G ) button.
menu
up
vol
down
1
Press the up/down button to select SCREEN
and then press the vol ( G ) button.
up
SPECIAL
LANGUAGE
ARC
SCREEN
SCREEN
TRANSPARENCY
PIP/DW
G
G
G
G
TO SET
G
G
vol
down
2
Press the up/down button to select
AUTO.CONFIG. and then press the vol
( G ) button.
up
AUTO.CONFIG.
LANGUAGE
AUTO.CONFIG.
CAPTION
V-POSITION
AUTO OFF
H-POSITION
SCREEN
PHASE
RGB-OUTPUT
RESET
G
GG
TO
G
G
G
G
SET
G
G
G
G
vol
down
• If adjustment of AUTO.CONFIG. is finished, it displayed OK.
• If the position of the screen is incorrect, operate the adjustment repeatly.
3
If picture needs to be adjusted more after auto adjustment, adjust HPOSITION, V-POSITION and PHASE. See following pages.
Tips
22
• It’s not out of order even though the screen is displayed odd on AUTO.CONFIG.
Composition
Adjusting horizontal / vertical postion
READY
Connection
Press the menu button and then press the up/down button
to select SPECIAL menu.
Press the vol ( G ) button.
menu
First step
PC Computer Mode Adjustments
up
vol
down
Basic function
1
Press the up/down button to select SCREEN
and then press the vol ( G ) button.
SPECIAL
LANGUAGE
ARC
SCREEN
SCREEN
TRANSPARENCY
PIP/DW
G
G
G
G
TO SET
G
G
up
vol
Time setting
down
Press the up/down button to select V-POSITION or H-POSITION and then press the vol
( G ) button.
LANGUAGE
AUTO.CONFIG.
CAPTION
V-POSITION
V-POSITION
AUTO OFF
H-POSITION
SCREEN
PHASE
RGB-OUTPUT
RESET
up
G
G
G
G
G
G
G
Picture & Sound
2
0
G
G
G
vol
down
Special function
3
Press the vol button to adjust until you get desired horizontal or vertical position and then press the enter button to remove menus.
• The adjustment range of V-POSITION is -50 ~ +50.
• The adjustment range of H-POSITION is -100 ~ +100.
• According to the input mode, the adjustment range of V-POSITION/H-POSITION
will be change.
• According to the input signal, the position of the picture will not change even
though adjusting the horizontal or vertical position with this function.
vol
Others
vol
enter
23
Picture Phase Adjustments
• If the picture isn’t clear after auto adjustment and especially if the characters are still trembling, then
adjust the picture phase manually.
READY
Press the menu button and then press the up/down button
to select SPECIAL menu.
Press the vol ( G ) button.
menu
up
vol
down
1
Use the up/down button to select SCREEN
and then press the vol ( G ) button.
SPECIAL
LANGUAGE
ARC
SCREEN
SCREEN
TRANSPARENCY
PIP/DW
G
G
G
G
TO SET
G
G
up
vol
down
2
Use the up/down button to select PHASE
and then press the vol ( G ) button.
up
LANGUAGE
AUTO.CONFIG.
CAPTION
V-POSITION
AUTO OFF
H-POSITION
SCREEN
PHASE
PHASE
RGB-OUTPUT
RESET
G
G
G
G
G
G
G
G
G
30
G
vol
down
3
Press the vol button to adjust phase and then press the enter button.
• The adjustment range of PHASE is 0 ~ 63.
vol
vol
enter
Initializing
• To initialize the adjusted value, select RESET with the up/down button and
then press the vol ( G ) button.
24
First step
PIP function
Connection
Watching the PIP (Picture in Picture)
pip
Press the pip button.
vol button, you can change the
PIP (S)
PIP (L)
Basic function
• Each time you press pip or
PIP size as below.
Composition
- Make sure to select RGB before operating.
- This function works only in the following resolution;
640x480, 800x600, 1024x768(only in Vertical frequency 60 Hz)
- When you select RGB or DTV for main picture in PIP/Twin picture, you can watch video, cable
TV or DVD for sub picture.
- It’s not out of order even though color of main picture is differ from PIP’s in PIP/Twin picture.
- If input mode of main picture change in PIP/Twin picture, sub picture disappeared automatically.
- When watching PIP/Twin picture, SCREEN is inactivated in special menu.
OFF
Time setting
PIP
F
PIP (S)
G
F
PIP (L)
Special function
PIP
Picture & Sound
<Small PIP>
G
<Large PIP>
F
OFF
Others
PIP
G
<Off>
25
Selecting the input signal
input select
Press the input select button in PIP mode.
• Each time you press input eslect button, you can select
VIDEO or COMPOENT alternatively.
VIDEO
COMPONENT
In case of COMPOENT, this function works only in 480i mode.
PIP INPUT
F
VIDEO
G
Moving the Sub picture
position
Press the position button in PIP mode.
• Each press of the position button change the position of the
sub picture as below.
26
First step
PIP function
Composition
Selecting the sound items
- This function works only in the following resolution;
640x480, 800x600, 1024x768(only in Vertical frequency 60 Hz)
- To use this function, connect PC/DTV video input to RGB-PC
INPUT(VGA/SVGA/XGA/SXGA) RGB-DTV INPUT(480p,/720p/1080i) socket and connect
PC/DTV audio inputs to AUDIO INPUT.
Connection
READY
menu
Basic function
Press the menu button and then press the up/down button
to select SPECIAL menu.
Press the vol ( G ) button.
up
vol
down
Time setting
1
Use the up/down button to select PIP/DW
and then press the vol ( G ) button.
SPECIAL
LANGUAGE
ARC
SCREEN
TRANSPARENCY
PIP/DW
G
G
G
G
TO SET
G
G
up
vol
down
up
LANGUAGE
DW
CAPTION
PIP
AUTO OFF
INPUT
SCREEN
SOUND SELECT
SOUND
RGB-OUTPUT
POSITION
G
LANGUAGE
DW
CAPTION
PIP
AUTO OFF
INPUT
SCREEN
SOUND
SELECT
RGB-OUTPUT
POSITION
G
G
G
G
G
G
G
G
Picture & Sound
2
Use the up/down button to select SOUND
SELECT and then press the vol ( G ) button.
G
G
G
G
SOUND
(M)
G
SOUND (S)
vol
Special function
down
3
Press the vol button to select SOUND (M) or
SOUND (S) and then press the enter button.
• Each time you press D / E button, you can
select SOUND (L) or SOUND (S) alternatively.
vol
G
G
G
G
SOUND
(M)
G
SOUND (S)
(S)
SOUND
Others
vol
G
enter
27
Twin picture function
- Make sure to select RGB before operating.
- This function works only in the following resolution;
640x480 (only in Vertical frequency 60 Hz)
twin picture
Press the twin picture button.
• Each time you press
select ON or OFF.
twin picture or vol button, you can
Main picture
Sub picture
DW
F
ON
G
<ON>
• To avoid showing a fixed
image on the screen, sub
picture moves every 2
hours.
:Center
DW
F
OFF
<OFF>
28
G
Downside
Upside
Center
First step
Composition
Selecting the input signal
Connection
input select
Press the input select button in TWIN PICTURE mode.
• Each time you press input eslect button, you can select
VIDEO or COMPOENT alternatively.
VIDEO
COMPONENT
Basic function
In case of COMPOENT, this function works only in 480i mode.
F
VIDEO
G
Time setting
PIP INPUT
Picture & Sound
Special function
Others
29
Using the remote control
Installing batteries
• Open the battery compartment cover on the back
of the remote control and insert the batteries with
correct polarity, match “+” with “+”, and match “-”
with “-”.
• Install two 1.5V “AA” alkaline batteries.
Don’t mix the used batteries with new batteries.
Notes for using the remote control
Make sure these are no
objects between the
remote control and its
sensor.
30
Don’t place the remote control
near a heater or damp place.
Strong impact on the remote control may cause operation failure.
Signal from the remote control
may be disturbed by sun light or
other strong light. In this case,
turn the set to other direction.
First step
Turning on the Monitor
Composition
- When using the remote control, aim it at its sensor on the Monitor.
Turning on the Monitor just after installation
Press the ON/OFF button on the Monitor. At this moment, the Monitor is
switched to standby mode. Press the
or INPUT SELECT button on the
Monitor or press the power on or video/pc button on the remote control and
then the Monitor will be switched on.
Basic function
2
Connection
1
Connect power cord correctly.
Turning on the Monitor (power cord is still connected)
1
If the Monitor is turned off with the
2
If the Monitor is turned off with the ON/OFF button on the Monitor
• Press the ON/OFF button on the Monitor to turn on the Monitor.
3
If the Monitor is turned off with the remote control and also the ON/OFF
button on the Monitor
Time setting
button on the Monitor
Press the
or INPUT SELECT button on the Monitor or press the power on
or video/pc button on the remote control and then the Monitor will be switched
on.
Picture & Sound
Special function
• Press the ON/OFF button on the Monitor and then press the
or INPUT
SELECT button on the Monitor or press the power on or video/pc button on
the remote control and then the Monitor will be switched on.
Others
Tips
• Adjusting volume level
Volume(G) button increases the level of sound and volume(F) button
decreases the level of sound.
31
Selecting language for the menus
READY
Press the menu button and then press the up/down button to
select SPECIAL menu.
Press the vol ( G ) button.
menu
up
vol
down
1
Press the up/down button to select
LANGUAGE and then press the
vol ( G ) button.
SPECIAL
LANGUAGE
ARC
SCREEN
TRANSPARENCY
PIP/DW
G
˙–„
G
ENGLISH
ESPAÑOL
PORTUGUÊS
FRANÇAIS
G
G
G
up
vol
down
2
Press the up/down button to select the
desired language.
up
down
3
Press the enter button.
enter
32
SPECIAL
LANGUAGE
ARC
SCREEN
TRANSPARENCY
PIP/DW
G
˙–„
G
ENGLISH
ESPAÑOL
PORTUGUÊS
FRANÇAIS
G
G
G
First step
Checking features
Composition
menu
Press the menu button.
2
Press the up/down button.
Connection
up
1
• Each press will cycle through the menus shown below.
down
PICTURE
D
MOVE
E
GNEXT
G
G
100
50
50
0
50
Basic function
APC
DRP
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
G
G
G
G
G
AEXIT
<Picture menu>
Time setting
SOUND
DASP
AVL
TREBLE
BASS
BALANCE
GNEXT
G
G
G
G
AEXIT
Picture & Sound
D
MOVE
E
G
50
50
0
<Sound menu>
SPECIAL
D
MOVE
E
GNEXT
G
G
G
Special function
LANGUAGE
ARC
SCREEN
TRANSPARENCY
PIP/DW
G
G
AEXIT
<Special menu>
vol
vol
down
3
Press the vol ( G ) button and then press the
up/down or vol button to select a function you
want to use.
Others
up
• Press the enter button to remove menus.
33
Setting sleep time
<This feature automatically turns the Monitor off after a preset time.>
Press the sleep button to set sleep time.
Each time you press the next preset setting
time is changed as shown below.
sleep
F --- G
F 10 G
F 20 G
F 30 G
F 120 G
F 90 G
F 60 G
F 240 G
F 180 G
SLEEP
F
30
G
• To release sleep time setting, press the sleep or
vol button repeatedly to select F --- G.
Tips
• When the sleep time you want is displayed on the screen, don’t press the
sleep button. The screen display disappears and sleep time is to be set.
• To check remaining sleep time after setting, press the sleep or enter button
just once.
• If you turn the Monitior off after setting the sleep timer, the setting will be
erased. The sleep timer will then have to be set again.
34
First step
Auto picture control
< APC sets the Monitor with the best picture appearance >
Composition
- This function isn’t select in RGB, PIP/TWIN PICTURE.
APC (Auto Picture Control)
Connection
apc
Press the apc button.
2
Press the apc or vol button to select your desired
picture condition.
Basic function
1
Time setting
F
CLEAR
G
Picture & Sound
APC
• Each press of vol button changes the screen display as
below.
CLEAR
SOFT
USER
Special function
• You can also select CLEAR, SOFT or USER in the PICTURE menu.
Others
35
Adjusting picture appearance
- You can’t adjust contrast, brightness, color, tint, sharpness in sub picture for PIP / Twin picture.
READY
Press the menu button and then press the up/down button to
select PICTURE menu.
Press the vol ( G ) button.
menu
up
vol
down
1
Press the up/down button to select
CONTRAST and then press the vol ( G )
button. (in case of adjusting contrast)
PICTURE
APC
DRP
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
G
G
100
50
50
0
50
up
vol
down
• Adjust BRIGHTNESS, COLOR, TINT and
SHARPNESS in the same way.
2
Press the vol button to make appropriate adjustment and then press the
enter button.
• Press the up/down button to select other items.
vol
36
vol
enter
PICTURE
APC
DRP
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
G
G
70
50
0
0
50
G
G
G
G
G
G
G
G
G
G
< This function stresses picture outline in showing a dark area light >
Composition
READY
Connection
Press the menu button and then press the up/down button to
select PICTURE menu.
Press the vol ( G ) button.
menu
First step
DRP (Digital Reality Picture)
up
vol
down
PICTURE
APC
DRP
G
G
100
50
50
0
50
G
CLEAR
SOFT
G
G
G
Time setting
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
up
Basic function
1
Press the up/down button to select
DRP and then press the vol ( G ) button.
G
vol
down
Press the up/down button to select
CLEAR or SOFT.
Picture & Sound
2
PICTURE
APC
DRP
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
G
G
100
50
50
0
50
G
CLEAR
SOFT
G
G
G
G
up
Special function
down
Others
3
Press the enter button.
enter
37
Selecting the screen item
- This function work only in video mode.
READY
Press the menu button and then press the up/down button to
select SPECIAL menu.
Press the vol ( G ) button.
menu
up
vol
down
1
Press the up/down button to select
SCREEN and then press the
vol ( G ) button.
SPECIAL
LANGUAGE
ARC
SCREEN
G
TRANSPARENCY
PIP/DW
G
G
G
TV
VCR
G
up
vol
down
2
Press the D /
VCR.
E
button to select TV or
• Select the VCR to stable condition of picture
when you are watching VCR.
• Select the TV in case of connecting external
equipment to monitor.(Except VCR)
• Each time you press the D / E button you can
select TV or VCR alternatively.
up
down
3
Press the enter button.
enter
38
SPECIAL
LANGUAGE
ARC
SCREEN
TRANSPARENCY
PIP/DW
G
G
G
G
G
TV
VCR
VCR
First step
Adjusting sound appearance
Composition
READY
menu
Connection
Press the menu button and then press the up/down button to
select SOUND menu.
Press the vol ( G ) button.
up
vol
down
SOUND
DASP
AVL
TREBLE
BASS
BALANCE
G
G
50
50
50
0
G
G
Time setting
Press the up/down button to select
TREBLE and then press the vol ( G )
button. (in case of adjusting treble)
Basic function
1
G
up
vol
down
Picture & Sound
• Adjust BASS and BALANCE in the same way.
• Press the up/down button to select other items.
vol
vol
Special function
2
Press the vol button to make appropriate adjustment and then press the
enter button.
SOUND
DASP
AVL
TREBLE
BASS
BALANCE
G
G
70
50
0
G
G
G
enter
Others
39
Auto sound control
DASP
• This function lets you enjoy the best sound without any special adjustment because the Monitor automatically adjusts the sound appropriate
to viewing program character by self-intelligence.
easy sound
1
Press the easy sound button.
2
Press the easy sound or vol button to select your
desired sound.
DASP
F
USER
G
• Each press of easy sound or vol button changes the
screen display as below.
FLAT
SPORTS
USER
CINEMA
MUSIC
• You can also select FLAT, SPORTS, CINEMA, MUSIC or
USER in the SOUND menu.
40
< This function keeps on an equal volume level even if you change channels>
Composition
- This function works only in case of connecting a cable box with the monitor.
READY
Connection
Press the menu button and then press the up/down button to
select SOUND menu.
Press the vol ( G ) button.
menu
First step
AVL (Auto Volume Leveler)
up
vol
Basic function
down
1
SOUND
DASP
AVL
TREBLE
BASS
BALANCE
G
G
50
50
0
G
ON
OFF
G
Time setting
Press the up/down button to select
AVL and then press the vol ( G )
button.
G
up
vol
down
Picture & Sound
2
Press the up/down button to select
ON or OFF.
SOUND
DASP
AVL
TREBLE
BASS
BALANCE
G
G
50
50
0
G
ON
OFF
G
G
Special function
up
down
Others
3
Press the enter button.
enter
41
Using Still function
- This function doesn’t work in RGB.
freeze
1
Press the freeze button.
• You can still the current picture.
• The sub picture is stilled in PIP or Twin picture mode.
<Moving image>
<Still image>
2
To finish this function, press the freeze button again.
Tips
• If still picture is on the screen for more than 5 minutes, the screen gets dark.
Any function is activated, the brightness of the screen gets restored.
• This function don’t worked in RGB mode.
42
First step
Adjusting OSD Transparency
Composition
READY
menu
Connection
Press the menu button and then press the up/down button to
select SPECIAL menu.
Press the vol ( G ) button.
up
vol
down
Press the up/down button to select
TRANSPARENCY and then press the
vol ( G ) button.
Basic function
1
SPECIAL
LANGUAGE
ARC
SCREEN
TRANSPARENCY
G
PIP/DW
G
G
G
G
5
Time setting
up
vol
down
• The adjustment range of TRANSPARENCY
is 0 ~ 5.
3
SPECIAL
LANGUAGE
ARC
SCREEN
TRANSPARENCY
PIP/DW
G
G
G
G
3
G
Special function
vol
Picture & Sound
2
Press the vol button to adjust OSD
transparency.
vol
Press the enter button.
Others
enter
43
Setting picture format
- You are available to 16:9 or 4:3 in RGB and 16:9 is only available in DTV 720p/1080i.
- If 4:3 is on the screen for a long time, that fixed image may remain visible.
ratio
Press the ratio button to select a desired picture
format.
• Each time you press ratio or vol button, you can select
16:9, 4:3 or ZOOM alternatively.
ARC
F
16 : 9
G
<16:9>
ARC
F
4:3
G
<4:3>
ARC
F
ZOOM
G
<Zoom>
• You can also select 16:9, 4:3 or ZOOM in the ARC of the
SPECIAL menu.
44
First step
Maintenance
Composition
- Early malfunction can be prevented. Careful and regular cleaning can extend the amount of
time you will have with your new Monitor. Be sure to turn the power off and pull out the plug
before you begin any cleaning.
Cleaning the screen
Connection
Basic function
1. Here’s a great way to keep the dust off your screen for a while. Wet a
soft cloth in a mixture of lukewarm water and a little fabric softener or
dish washing detergent. Wring the cloth until it’s almost dry, and then
use it to wipe the screen.
2. Make sure the excess water is off the screen, and then let it air-dry
before you turn on your Monitor.
Time setting
Cleaning the cabinet
Picture & Sound
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth.
Special function
Extended absence
Others
If you leave your Monitor dormant for a long time (such as a
vacation), it’s a good idea to unplug the power to protect
against possible damage from lightning or power surges.
45
Troubleshooting check list
• Check whether the Monitor is turned on.
No picture &
No sound
Picture OK &
No sound
• Check the power cord.
• Plug another product’s power cord into the wall outlet where
the Monitor’s power cord was plugged in.
• Press the VOLUME (G) button.
• Check to see if there is any object between the Plasma
Display and the remote control causing obstruction.
The remote control
doesn’t work
• Check to see if the batteries are installed with the correct
polarities. (Refer to p.30)
• Replace new batteries. (Refer to p.30)
• Select COLOR in the PICTURE menu and press the VOLUME (G) button. (Refer to p.36)
No or Poor color
or Poor picture
No output from one
of the speakers
Strange sound
from the Monitor
46
• Keep a certain distance between the Monitor and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the
screen gets dark.)
• Adjust BALANCE in the SOUND menu. (Refer to p.39)
• The reason strange sound comes from the Monitor when turning the Monitor on or off is due to the signals being input or
output to the Monitor.
This strange noise does not mean that the Monitor is faulty.
First step
Product specifications
Composition
Height (inches)
34.8
Depth (inches)
3.9
Weight (pounds)
154.3
Power consumption (watts)
320
Power requirement
AC 120V ~ 60Hz
Resolution
1280 x 720 (Dot)
Color
16,770,000 (256 steps of each R, G and B)
Picture & Sound
57.3
Time setting
Width (inches)
Basic function
DPDP60W
Connection
MODEL
Special function
• This product specifications above can be changed without notice for quality improvement.
Others
47
Model number : DPDP60W
Serial number :
PLASMA DISPLAY PANEL
Please read this owner’s manual carefully before
operating the Monitor.
Retain it for future reference.
Record model number and serial number of the
Monitor.
See the label attached on the back of the Monitor
and quote this information to your dealer when you
require service.
DPDP60W
OWNER’S MANUAL
P/NO : 3828VA0277B
(NP00KA)
ON/OFF
INPUT SELECT
VOLUME
Download PDF