Installation Manual Installation and Appliance Setup

Installation Manual Installation and Appliance Setup
Installation Manual
Installation and Appliance Setup
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
Models:
TRUE-36C
TRUE-36H
TRUE-36S
TRUE-42C
TRUE-42H
TRUE-42S
TRUE-50C
TRUE-50H
TRUE-50S
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
Pour demander un exemplaire en français de ce Manuel
du propriétaire, visitez www.heatnglo.com/translations.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
1
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
Installation Standard Work Checklist . . . . . . . . . . . . . . . . . . . . 3
1 Product Specific and Important Safety Information
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glass Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
4
4
4
4
4
4
4
5
A. Design and Installation Considerations . . . . . . . . . . . . . . . 6
B. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . . 6
C. Inspect Appliance and Components . . . . . . . . . . . . . . . . . . 6
3 Framing and Clearances
Appliance/Decorative Front Dimension Diagrams . . . . . . . 7
Clearances to Combustibles . . . . . . . . . . . . . . . . . . . . . . 12
Constructing the Appliance Chase . . . . . . . . . . . . . . . . . . 14
Hearth Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4 Termination Location and Vent Information
A.
B.
C.
D.
E.
F.
G.
Vent Termination Minimum Clearances . . . . . . . . . . . . . .
Chimney Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PVK-80 and PVI-SLP Information . . . . . . . . . . . . . . . . . .
16
17
18
18
18
19
25
5 Vent Clearances and Framing
A.
B.
C.
D.
E.
Assemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Vertical Termination Requirements. . . . . . . . . . . . . . . . . .
Horizontal Termination Requirements . . . . . . . . . . . . . . .
8 Electrical Information
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
B. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .
Wall Penetration Framing/Firestops . . . . . . . . . . . . . . . . .
Ceiling Firestop/Floor Penetration Framing . . . . . . . . . . .
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . .
Installing the Optional Heat-Zone® Gas Kit . . . . . . . . . . .
26
26
27
27
28
A.
B.
C.
D.
E.
Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
39
39
40
10 Finishing
A.
B.
C.
D.
Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Finishing Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
Decorative Front Dimensions for Finishing . . . . . . . . . . .
41
42
44
46
11 Appliance Setup
A. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . .
C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D. Install Teco-Sil and Mystic Embers . . . . . . . . . . . . . . . . .
E. Glowing Ember Placement. . . . . . . . . . . . . . . . . . . . . . . .
F. LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G. Install the Log Assembly . . . . . . . . . . . . . . . . . . . . . . . . .
H. Install Decorative Front . . . . . . . . . . . . . . . . . . . . . . . . . .
47
49
49
49
50
50
51
57
12 Reference Materials
A. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 58
B. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6 Appliance Preparation
A. Vent Collar Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . 29
B. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 30
C. Installing Non-Combustible Facing Material . . . . . . . . . . 31
 = Contains updated information.
2
32
33
33
34
35
9 Gas Information
2 Getting Started
A.
B.
C.
D.
A.
B.
C.
D.
E.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15

A.
B.
C.
D.
E.
F.
G.
H.
7 Venting and Chimneys
Installation Standard Work Checklist
ATTENTION INSTALLER:
Follow this Standard Work Checklist
This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in
this installation manual.
Customer:
Date Installed:
Lot/Address:
Location of Fireplace:
Installer:
Model (circle one): TRUE-36
TRUE-50
Dealer/Distributor Phone #
TRUE-42
Serial #:
WARNING! Risk of Fire or Explosion! Failure to install appliance according to these instructions can lead to a
¿re or explosion.
Appliance Install Information
Veri¿ed clearances to combustibles requirements are maintained. (Pg. 12-14)
Veri¿ed that the chase is insulated and sealed. (Pg. 14)
Veri¿ed mantel and wall clearance requirements are maintained. (Pg. 44-45)
Veri¿ed hearth extension requirements are maintained. (Pg. 15)
Veri¿ed appliance is leveled and secured. (Pg. 30)
Veri¿ed required factory-supplied non-combustible board installed. (Pg. 31)
YES
IF NO, WHY?
___________________
___________________
___________________
___________________
___________________
___________________
Venting/Chimney Section 7 (Pg. 32-35)
Veri¿ed venting con¿guration complies to vent diagrams.
Veri¿ed venting installed, locked and sealed/secured in place.
Veri¿ed venting meets clearance to combustible requirements.
Veri¿ed wall/ceiling ¿restops are installed (if applicable).
Veri¿ed attic insulation shield is installed (if applicable).
Veri¿ed Exterior wall/Roof Àashing is installed and sealed.
Veri¿ed termination cap is installed and sealed.
___________________
___________________
___________________
___________________
___________________
___________________
___________________
Electrical Section 8 (Pg. 36-38)
Veri¿ed unswitched power (110-120 VAC) provided to the appliance.
Veri¿ed wall switch wires are properly installed (if applicable).
___________________
___________________
Gas Section 9 (Pg. 39-40)
Veri¿ed appliance is using proper fuel type.
If converted, veri¿ed proper fuel conversion kit was used.
Veri¿ed that gas components (¿ttings, pressure taps, etc) are leak free and ¿replace is
operating under correct pressures.
Finishing Section 10 (Pg. 41-46)
Veri¿ed that ¿nish material does not interfere with install/operation of decorative front.
Veri¿ed combustible materials are not installed in non-combustible areas.
Veri¿ed all clearances meet installation manual requirements.
Veri¿ed mantels/wall projections comply with installation manual requirements.
Appliance Setup Section 11 (Pg. 47-57)
Veri¿ed all packaging and protective materials are removed (inside & outside of appliance).
Veri¿ed Teco-Sil installed and properly fogged with black high temperature paint.
Veri¿ed Lava Rock, Mystic Embers, Glowing Embers, and logs installed correctly.
Veri¿ed ¿xed glass assembly installed and secured.
Veri¿ed that a required decorative door option is installed properly.
Veri¿ed remote control has been programmed and is fully functional.
Veri¿ed proper air shutter setting for installation type and vent con¿guration.
Manual bag and all of its contents are removed from inside/under
the appliance and given to party responsible for use and operation.
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
Hearth & Home Technologies recommends the following:
• Photographing the installation and copying this checklist for your ¿le.
• That this checklist remain visible at all times on the appliance until the installation is complete.
Comments: Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective
action needed ____________________________________________________________________________________
Comments Communicated to party responsible ____________________ by ______________________on ___________
(Builder / Gen. Contractor/) (Installer)
(Date)
Î = Contains updated information.
2282-982B 11/13
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
3
1
Product Specific and Important Safety Information
A. Appliance Certification
D. High Altitude Installations
MODELS: TRUE-36C, TRUE-36H, TRUE-36S,
TRUE-42C, TRUE-42H, TRUE-42S
TRUE-50C, TRUE-50H, TRUE-50S
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Heater
STANDARD: ANSI Z21.88-2014 • CSA 2.33-2014
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
E. Non-Combustible Materials Specification
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Glass Specifications
This appliance is equipped with 5 mm ceramic glass with
an anti-reflective coating. Replace glass only with glass
with identical specifications. Please contact your dealer
for replacement glass.
C. BTU Specifications
Maximum
Input
BTU/h
Minimum
Input
BTU/h
Orifice
Size
(DMS)
US
(0-2000 FT)
45,500
28,000
#30
CANADA
(2000-4500 FT)
41,000
25,000
#31
US
(0-2000 FT)
43,500
27,500
#47
CANADA
(2000-4500 FT)
39,000
25,000
#48
US
(0-2000 FT)
55,500
30,500
#26
CANADA
(2000-4500 FT)
50,000
27,500
#27
US
(0-2000 FT)
51,500
29,000
#45
CANADA
(2000-4500 FT)
46,500
26,000
#46
US
(0-2000 FT)
65,000
36,000
#24
CANADA
(2000-4500 FT)
58,500
32,500
#25
US
(0-2000 FT)
63,500
32,500
#43
CANADA
(2000-4500 FT)
57,000
29,500
#44
Models
(U.S. or Canada)
TRUE-36 (NG)
TRUE-36 (LP)
TRUE-42 (NG)
TRUE-42 (LP)
TRUE-50 (NG)
TRUE-50 (LP)
4
Check with your local gas utility to determine proper
orifice size.
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750 ºC shall be considered
non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection,
in compliance with the applicable electrical codes,
when it is installed in locations such as in bathrooms
or near sinks.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR 5.08(2)
(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
5
2
Getting Started
A. Design and Installation Considerations
C. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
Before installing, determine the following:
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping requirements.
• Electrical wiring requirements.
• Framing and finishing details.
• Whether optional accessories—devices such as a wall
switch or remote control—are desired.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory
trained professionals, or technicians supervised by
an NFI certified professional (www.nficertified.org).
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Framing material
Pliers
Hammer
Phillips screwdriver Manometer
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
Reciprocating saw
Flat blade screwdriver
Non-corrosive leak check solution
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure
rating)
6
• The vent system components and decorative fronts may
be shipped in separate packages.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
3
Framing and Clearances
A. Appliance/Decorative Front Dimension Diagrams
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
APPLIANCE DIMENSION DIAGRAM (TRUE-36)
L
N
M
J
K
A
HEAT-ZONE® PORT
HEAT-ZONE®
PORT
ELECTRICAL
ACCESS
E
GAS
ACCESS
D
H
F
I
G
P
O
B
C
Q
R
Appliance Dimensions Table TRUE-36
Location
Inches
Millimeters
Location
Inches
Millimeters
A
61
1549
J
24
610
B
35-7/8
911
K
23-1/2
597
C
39-7/8
1013
L
59-1/4
1505
D
31-1/16
789
M
16
406
E
57-5/8
1464
N
29-5/8
752
F
35-3/16
894
O
3-7/8
98
G
34-3/16
868
P
2-3/4
70
H
54-15/16
1395
Q
10-7/8
276
I
41-3/8
1051
R
16-1/8
410
Figure 3.1 Appliance Dimensions (TRUE-36)
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
7
APPLIANCE DIMENSION DIAGRAM (TRUE-42/TRUE-50)
L
N
M
J
K
A
HEAT-ZONE® PORT
HEAT-ZONE®
PORT
ELECTRICAL
ACCESS
E
GAS
ACCESS
D
H
F
I
G
P
O
B
C
Q
R
Appliance Dimensions Table TRUE-42
Location
Inches
Millimeters
Location
Inches
Millimeters
A
67
1702
J
24
610
B
41-7/8
1064
K
23-1/2
597
C
45-7/8
1165
L
65-5/16
1659
D
36-1/16
916
M
16
406
E
62-5/8
1591
N
32-11/16
830
F
40-3/16
1021
O
3-7/8
98
G
39-3/16
995
P
2-3/4
70
H
59-15/16
1522
Q
10-7/8
276
I
46-3/8
1178
R
16-1/8
410
Location
Inches
Millimeters
Appliance Dimensions Table TRUE-50
Location
Inches
Millimeters
A
75
1905
J
24
610
B
49-7/8
1267
K
23-1/2
597
C
53-7/8
1368
L
73-5/16
1862
D
40-1/16
1018
M
16
406
E
66-5/8
1692
N
36-11/16
932
F
44-3/16
1122
O
3-7/8
98
G
43-3/16
1097
P
2-3/4
70
H
63-15/16
1624
Q
10-7/8
276
I
50-3/8
1280
R
16-1/8
410
Figure 3.2 Appliance Dimensions (TRUE-42 & TRUE-50)
8
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
DECORATIVE FRONT DIMENSION DIAGRAM (TRUE-36)
See Section 10 for facing and finishing detail.
FS-36
FS-36A
35-9/16 IN.
903 mm)
36-13/16 IN.
(935 mm)
40-11/16 IN.
(1035 mm)
3-5/8 IN.
(92 mm)
1-5/16 IN.
(33 mm)
35-7/16 IN.
(900 mm)
31-5/8 IN.
(803 mm)
36-3/4 IN.
(934 mm)
40-11/16 IN.
(1035 mm)
3-5/8 IN.
(92 mm)
1-5/16 IN.
(33 mm)
FORGE-36A
FORGE-36
36-3/4 IN.
(908 mm)
35-7/16 IN.
(889 mm)
36-3/4 IN.
(934 mm)
35-7/16 IN.
31-5/8 IN.
(900 mm)
(803 mm)
40-3/4 IN.
(1035 mm)
40-3/4 IN.
(1035 mm)
1-5/16 IN.
(33 mm)
1-5/16 IN.
(33 mm)
Figure 3.3 Decorative Front Dimensions (TRUE-36)
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
9
DECORATIVE FRONT DIMENSION DIAGRAM (TRUE-42)
See Section 10 for facing and finishing detail.
FS-42
FS-42A
40-9/16 IN.
(1030 mm) 41-13/16 IN.
(1062 mm)
46-11/16 IN.
(1186 mm)
3-9/16 IN.
(91 mm)
1-1/4 IN.
(32 mm)
40-9/16 IN.
(1030 mm)
36-3/4 IN.
(934 mm)
46-11/16 IN.
(1186 mm)
3-9/16 IN.
(91 mm)
1-1/4 IN.
(32 mm)
FORGE-42A
FORGE-42
41-13/16IN.
(1062 mm)
40-9/16 IN.
(1030 mm)
41-11/16 IN.
(1059 mm)
40-7/16 IN.
(1027 mm)
36-5/8 IN.
(930 mm)
46-3/4 IN.
(1187 mm)
46-11/16 IN.
(1186 mm)
1-1/4 IN.
(32 mm)
Figure 3.4 Decorative Front Dimensions (TRUE-42)
10
41-13/16 IN.
(1062 mm)
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
1-1/4 IN.
(32 mm)
DECORATIVE FRONT DIMENSION DIAGRAM (TRUE-50)
See Section 10 for facing and finishing detail.
FS-50
FS-50A
44-7/16 IN.
1128 mm) 45-11/16 IN.
(1161mm)
54-11/16 IN.
(1390 mm)
3-9/16 IN.
(91 mm)
1-1/4 IN.
(32 mm)
44-7/16 IN.
(1129 mm)
45-11/16 IN.
(1161 mm)
40-5/8 IN.
(1032 mm)
54-11/16 IN.
(1390 mm)
3-9/16 IN.
(91 mm)
1-1/4 IN.
(32 mm)
FORGE-50A
FORGE-50
45-11/16 IN.
44-7/16 IN.
(1161 mm)
(1128 mm)
40-5/8 IN.
(1031 mm)
45-11/16 IN.
(1161mm)
44-7/16 IN.
(1128 mm)
54-3/4 IN.
(1391 mm)
54-3/4 IN.
(1391 mm)
1-1/4 IN.
(32 mm)
1-1/4 IN.
(32 mm)
Figure 3.5 Decorative Front Dimensions (TRUE-50)
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
11
B. Clearances to Combustibles
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
When selecting a location for the appliance it is important
to consider the required clearances to walls (see Figure
3.6).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
A
D
D
A
B
C
F
B
E
Note: Dimensions below refer to a framed wall on
which 1/2 inch wall sheathing has not been installed.
E
F
B
TRUE-36
TRUE-42
TRUE-50
A
B
C
D
E
F
Inches
74-1/4
59-1/2
105
26-1/2
23-1/2
29-3/4
Millimeters
1886
1511
2667
673
597
756
Inches
78-9/16
65-9/16
111-1/16
28-5/8
23-1/2
32-13/16
Millimeters
1995
1665
2821
727
597
33
Inches
84-1/4
73-9/16
119-1/8
31-1/2
23-1/2
36-13/16
Millimeters
2140
1868
3026
800
597
935
Figure 3.6 Appliance Locations
12
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Non-Combustible Zone
2 X 4 FRAMING
MATERIAL
1/2 IN. BUILDING MATERIAL
(MAY BE COMBUSTIBLE)
PIPE IS FOR VISUAL
REFERENCE ONLY
NO COMBUSTIBLES
IN HATCHED AREA
NOTE:
2 X 4 HEADER
CONFIGURATION
39 IN.
1 IN.
FACTORY-SUPPLIED
1/2 IN.
NON-COMBUSTIBLE
BOARD
= COMBUSTIBLES
NOT ALLOWED
Figure 3.7 Non-Combustible Zone
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
13
To further prevent drafts, the wall shield and ceiling firestops should be caulked with caulk with a minimum of
300ºF continuous exposure rating to seal gaps. Gas
line holes and other openings should be caulked with
caulk with a minimum of 300ºF continuous exposure rating
or stuffed with unfaced insulation. If the appliance is being
installed on a cement surface, a layer of plywood may be
placed underneath to prevent conducting cold up into the
room.
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
C. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
• Failure to maintain airspace may cause overheating and
a fire.
A
E
(FROM APPLIANCE
OPENING TO CEILING)
F
B
H
G
C
J
D
I
NOTE: 2 X 4 Header positioned vertically. See also Figure 3.7.
* MINIMUM FRAMING DIMENSIONS
TRUE-36
TRUE-42
TRUE-50
A
B
C
D
E
F
G
H
I
J
Rough
Opening
(Vent Pipe)
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width)
Clearance
to Ceiling
Combustible
Floor
Combustible
Flooring
Behind
Appliance
Sides of
Appliance
Front of
Appliance
Inches
10
56
24
59-1/2
52
0
1
1
36
Millimeters
254
1422
610
1511
1321
0
25
25
914
Inches
10
61
24
65-9/16
52
0
1
1
36
Millimeters
254
1549
610
1665
1321
0
25
25
914
Inches
10
65
24
73-9/16
52
0
1
1
36
Millimeters
254
1651
610
1868
1321
0
25
25
914
See Section 3.D.
* Adjust framing dimensions for interior sheathing (such as sheetrock)
Figure 3.8 Clearances to Combustibles
14
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
D. Hearth Extension
WARNING! Risk of Fire! Non-combustible hearth extension may be required when appliance is installed on combustible surface.
•
Hearth extension must be non-combustible and
serves to protect combustible floors in front of appliance. See Figure 3.9 and Figure 3.10.
•
The base of the fireplace may sit on a combustible
surface. See Figure 3.10. The area in front of the
appliance must be protected by a non-combustible
hearth extension, unless the appliance is raised a
minimum of three inches above the combustible floor
or hearth. See Figure 3.10 and Figure 3.11.
•
If a hearth greater than one inch in thickness is desired, the appliance must be raised by the equivalent
height to ensure that the hearth extension does not
interfere with the installation of the glass assembly
required for fireplace operation. See Figure 3.10.
NOTICE: DO NOT install a hearth that is greater than
one inch thick. Hearth will interfere with installation of
glass assembly. Total hearth height must not exceed one
inch from bottom of appliance when appliance is installed
directly on floor (including mortar, backer material, etc.).
NON-COMBUSTIBLE
BOARD
HEARTH CLEARANCE
BRACKET
NON-COMBUSTIBLE
HEARTH EXTENSION
1 IN. THICK MAX.
WOOD OR OTHER COMBUSTIBLE
FLOOR OR PLATFORM
Figure 3.10 Appliance Installed on Combustible Surface
Non-Combustible Hearth Extension REQUIRED.
NON-COMBUSTIBLE
BOARD
A
NO
N-
HEARTH CLEARANCE
BRACKET
CO
MB
US
B
MODEL
TRUE-36
TRUE-42
TRUE-50
in.
12
12
12
A
TIB
LE
mm
305
305
305
B
in.
57-1/4
63-5/16
71-5/16
4 IN.
mm
1454
1608
1811
Figure 3.9 Non-Combustible Hearth Extension Dimensions
1/2 IN. MAX.
THICKNESS
COMBUSTIBLE
BUILDING
MATERIAL
3 IN. MIN.
BOTTOM OF
FIREPLACE
WOOD OR OTHER COMBUSTIBLE
FLOOR OR PLATFORM
Figure 3.11 Appliance Raised a Minimum of 3 Inches Above
Combustible Surface. Non-Combustible Hearth Extension NOT REQUIRED.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
15
4
Termination Location and Vent Information
A. Vent Termination Minimum Clearances
WARNING
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
Fire Risk.
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
Gas, Wood or Fuel Oil
Termination Cap
B
A*
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Gas
Termination
Cap **
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
*
**
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
Figure 4.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5*
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
NOTICE: TRUE-50 Models Only
Horizontal vent terminations are NOT approved for
installation with vinyl siding or vinyl soffits. Permanent
damage to vinyl siding or vinyl soffits may occur.
NOTICE: TRUE-36 and TRUE-42 Only:
Horizontal vent terminations ARE approved for installation
with vinyl siding and/or vinyl soffits provided the VPK-DV
(vinyl protector kit) is installed. Permanent damage to vinyl
siding or vinyl soffits may occur.
* 3 foot minimum in snow regions
Figure 4.1 Minimum Height From Roof To Lowest Discharge
Opening
16
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
B. Chimney Diagram
O
N
P
R
F
C
Q
V
V
B
J
D
V
B
V
M
A
A
B
C
X
G
V
V = VENT TERMINAL
X = AIR SUPPLY INLET
V
= 12 inches.................clearances above grade, veranda, porch,
deck or balcony
= 12 inches.................clearance to window or door that may
be opened, or to permanently closed
window
= 18 inches.................clearance below an unventilated/ventilated soffit with non-vinyl siding
= 42 inches .................clearance below a vinyl soffit with nonvinyl siding. TRUE-50 is not approved
for use with vinyl siding or vinyl soffits.
= 6 inches...................clearance to outside corner
E
= 6 inches...................clearance to inside corner
= 3 ft. (Canada) ..........not to be installed above a gas meter/
regulator assembly within 3 feet horizontally from the center-line of the regulator
G = 3 ft ...........................clearance to gas service regulator vent
outlet
H
= 12 inches.................clearance to non-mechanical (unpowered) air supply inlet, combustion air
inlet or direct-vent termination
i
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap must
be a minimum of 3 feet below termination.
J
= 7 ft. ......................... On public property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves
both dwellings.
= 6 inches.................clearance from sides of electrical
service
= 12 inches................clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.
V
Electrical
Service
= 24 inches ....... clearance under veranda, porch, deck, balcony or
overhang
42 inches ..... vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor.
K
V
C
V
Covered Alcove Applications
TRUE-50 is not approved for use with vinyl siding or vinyl soffits.
N = 6 inches ........non-vinyl sidewalls
12 inches ......vinyl sidewalls
O = 18 inches .......clearance below an unventilated/ventilated soffit
with non-vinyl siding
= 18 inches ......clearance below an unventilated/ventilated soffit
with vinyl siding. Requires a vinyl protector kit (VPK-DV).
= 42 inches ......clearance below a vinyl soffit with non-vinyl siding
= 42 inches ......clearance below a vinyl soffit with vinyl siding.
Requires a vinyl protector kit (VPK-DV).
P = 8 ft.
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUAL
2 caps
6 feet
1 x Q ACTUAL
3 caps
9 feet
2/3 x Q ACTUAL
4 caps
12 feet
1/2 x Q ACTUAL
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
Measure vertical clearances from this surface.
CLEARANCE = 6 IN.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffic areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.
•
Local codes or regulations may require different
clearances.
•
Vent system termination is NOT permitted in screened
porches.
•
Vent system termination is permitted in porch areas with
two or more sides open.
•
Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
Vinyl protection kits are required for use with vinyl siding.
M
Figure 4.3 Minimum Clearances for Termination
H
V
V
K
(Spaces open only on one side and with an overhang)
F
L
E
A
= 42 inches .................clearance below a vinyl soffit with vinyl
siding. Requires a vinyl protector kit
(VPK-DV). TRUE-50 is not approved
for use with vinyl siding or vinyl soffits.
D
V
H
V
= AREA WHERE TERMINAL IS NOT PERMITTED
= 18 inches .................clearance below an unventilated/ventilated soffit with vinyl siding. Requires
a vinyl protector kit (VPK-DV).TRUE-50
is not approved for use with vinyl siding
or vinyl soffits.
K
L
H or i
B
V
•
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
17
C. Approved Pipe
This appliance is approved for use with Hearth & Home
Technologies DVP venting systems. Refer to Section
12.A for vent component information and dimensions.
Y
DO NOT mix pipe, fittings or joining methods from different manufacturers.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
X
Vent
Type
D. Use of Elbows
Diagonal runs have both vertical and horizontal vent
aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect. See
Figure 4.4.
DVP
X
Inches Millimeters
4-1/2
114
Inches
17
Y
Millimeters
432
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows.
See Figure 4.4.
X
Figure 4.5 shows the vertical and horizontal offsets for
DVP elbows.
X
Vent Type
RISE
E
LE FFE
N C
G TI
TH V
E
VERTICAL
DVP
X
Inches
16-1/4
Millimeters
413
Figure 4.5 Vertical and Horizontal Offset for DVP Elbows
RUN
E. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards:
HORIZONTAL
Effective Length
Rise/Run
DVP
Pipe
Inches
Millimeters
Inches
Millimeters
DVP4
DVP6
4
6
102
152
2-3/4
4-1/4
70
108
DVP12
12
305
8-1/2
216
DVP24
DVP36
DVP48
24
36
48
610
914
1219
17
25-1/2
34
432
648
864
DVP6A
3 to 6
76 to 152
2-1/8-4-1/4
54-108
DVP12A
3 to 12
76 to 305
2-1/8-8-1/2
54-216
• Pipe measurements are shown using the effective length
of pipe. See Section 12.A for information on effective
length of pipe components.
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
4.3).
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
Figure 4.4
18
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
F. Vent Diagrams
WARNING! Risk of Fire. This appliance requires a minimum of 24 inches of vertical venting before attaching any elbow to
the appliance. DO NOT attach elbow directly to the appliance.
General Rules:
• This appliance is approved for use with Hearth & Home Technologies DVP venting systems ONLY.
• When penetrating a combustible wall, a wall shield firestop must be installed.
• When penetrating a combustible ceiling, a ceiling firestop must be installed.
• This appliance requires a minimum of 24 inches of vertical pipe attached directly to the appliance starting collar before
attaching a 90 degree or 45 degree elbow.
• Horizontal termination cap should have a 1/4 inch downward slant to allow any moisture in cap to be released.
Top Vent - Horizontal Termination
One Elbow
• TRUE-36(NG/LP), TRUE-42(NG), and TRUE-50(NG/LP) models
require a minimum of 24 inches of vertical venting before attaching
any elbow to the appliance.
Note: Flue restrictor is permitted ONLY on 30 ft. minimum
vertical runs with no elbows.
TRUE-36 (NG/LP), TRUE-42 (NG),
TRUE-50 (NG/LP)
V1 Minimum
WARNING! Risk of Fire!
• TRUE-42(LP) model requires a minimum of 36 inches of vertical
venting before attaching any elbow to the appliance.
DO NOT attach elbow directly to the appliance.
H1 Maximum
2 ft
610 mm
7 in*
178 mm
2.5 ft
762 mm
17 in
432 mm
3 ft
914 mm
2 ft
610 mm
4 ft
1.2 m
4 ft
1.2 m
5 ft
1.5 m
9 ft
2.7 m
6 ft
1.8 m
12 ft
3.7 m
7 ft
2.1 m
14 ft
4.3 m
10 ft
3.0 m
20 ft
6.1 m
20 ft
6.1 m
40 ft
12.2 m
V1
H1
After V1= 6 ft then H1 = 2 x V ft Maximum
V1 + H1 = 60 ft Maximum
*when used with approved termination caps
TRUE-42 (LP)
V1 Minimum
H1 Maximum
3 ft
914 mm
10 in.
254 mm
4 ft
1.2 m
4 ft
1.2 m
5 ft
1.5 m
9 ft
2.7 m
6 ft
1.8 m
12 ft
3.7 m
7 ft
2.1 m
14 ft
4.3 m
10 ft
3.0 m
20 ft
6.1 m
20 ft
6.1 m
40 ft
12.2 m
After V1= 6 ft then H1 = 2 x V ft Maximum
V1 + H1 = 60 ft Maximum
*when used with approved termination caps
Figure 4.6
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
19
Two Elbows
WARNING! Risk of Fire!
Note: Flue restrictor is permitted ONLY on 30 ft. minimum
vertical runs with no elbows.
• TRUE-36(NG/LP),TRUE-42(NG/LP) and TRUE-50(NG/LP) models
require a minimum of 36 inches of vertical venting before attaching
any elbow to the appliance for the venting configuration in Figure 4.7.
DO NOT attach elbow directly to the appliance.
H2
V1
H1
INSTALLED
HORIZONTALLY
TRUE-36 (NG/LP), TRUE-42 (NG/LP),
TRUE-50 (NG/LP)
H1+ H2
V1 Minimum
3 ft
914 mm
18 in
457 mm
4 ft
1.2 m
3 ft
914 mm
5 ft
1.5 m
7 ft
2.1 m
6 ft
1.8 m
10 ft
3.0 m
7 ft
2.1 m
14 ft
4.3 m
8 ft
2.4 m
16 ft
4.9 m
9 ft
2.7 m
18 ft
5.5 m
10 ft
3.0 m
20 ft
6.1 m
V1 + H1 + H2= 60 ft Maximum
H1 + H2= 20 ft Maximum
Figure 4.7
20
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Top Vent - Horizontal Termination - (continued)
Three Elbows
WARNING! Risk of Fire!
Note: Flue restrictor is permitted ONLY on 30 ft. minimum
vertical runs with no elbows.
• TRUE-36(NG/LP), TRUE-42(NG/LP) and TRUE-50 (NG/LP) models
require a minimum of 24 inches of vertical venting before attaching
any elbow to the appliance.
DO NOT attach elbow directly to the appliance.
H2
V2
H1
V1
TRUE-36 (NG/LP), TRUE-42 (NG/LP), TRUE-50 (NG/LP)
V1
H1
V2
H2
2 ft
610 mm
7 in
178 mm
*
H2 Max = 2 X V2
3 ft
914 mm
2 ft
610 mm
*
H2 Max = 2 X V2
4 ft
1.2 m
4 ft
1.2 m
*
H2 Max = 2 X V2
5 ft
1.5 m
9 ft
2.7 m
*
H2 Max = 2 X V2
6 ft
1.8 m
12 ft
3.7 m
*
H2 Max = 2 X V2
7 ft
2.1 m
14 ft
4.3 m
*
H2 Max = 2 X V2
10 ft
3.0 m
20 ft
6.1 m
*
H2 Max = 2 X V2
V1 + H1 must be adhered to.
* V2 has no specific restrictions EXCEPT,
Ht max = 2 x Vt and Vtotal + Htotal cannot exceed 60 ft Maximum
Figure 4.8
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
21
Top Vent - Vertical Termination
No Elbow
V1 = 50 ft. Max. (15.2 m)
V1 = 2 ft. Min. (610 mm)
Note: Flue restrictor is permitted ONLY on 30 ft. minimum
vertical runs with no elbows.
NOTE: Flue Restrictor
ships in manual bag
assembly.
FLUE
RESTRICTOR
Figure 4.10 Flue Restrictor Installation
V1
Figure 4.9
22
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Top Vent - Vertical Termination - (continued)
TRUE-36 (NG/LP), TRUE-42 (NG/LP),
2 ELBOWS
TRUE-50 (NG/LP)
Note: Flue restrictor is permitted ONLY on 30 ft. minimum
vertical runs with no elbows.
V1
WARNING! Risk of Fire!
• TRUE-36(NG/LP), TRUE-42(NG/LP) and TRUE-50 (NG/LP) models
require a minimum of 24 inches of vertical venting before attaching
any elbow to the appliance.
DO NOT attach elbow directly to the appliance.
H1
V2
2 ft
610 mm
1 ft
305 mm
*
3 ft
914 mm
3 ft
914 mm
*
4 ft
1.2 m
4 ft
1.2 m
*
5 ft
1.5 m
9 ft
2.7 m
*
6 ft
1.8 m
12 ft
3.7 m
*
V1 + V2 + H1 = 50 ft (15.2 m) Max.
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 60 ft (18.3 m).
After V1 = 6 ft, then H1 Max.= V1 x 2
V2
H1
V1
Figure 4.10
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
23
Top Vent - Vertical Termination - (continued)
Three Elbows
TRUE-36 (NG/LP), TRUE-42 (NG/LP), TRUE-50 (NG/LP)
V1
Note: Flue restrictor is permitted ONLY on 30 ft. minimum
vertical runs with no elbows.
H1
H2
V2
Ht Max.
2 ft
610 mm
*
*
**
7 in
178 mm
3 ft
914 mm
*
*
**
2 ft
610 mm
WARNING! Risk of Fire!
4 ft
1.2 m
*
*
**
4 ft
1.2 m
• TRUE-36(NG/LP), TRUE-42(NG/LP) and TRUE-50 (NG/LP)
models require a minimum of 24 inches of vertical venting
before attaching any elbow to the appliance.
5 ft
1.5 m
*
*
**
8 ft
2.4 m
6 ft
1.8 m
*
*
**
12 ft
3.7 m
7 ft
2.1 m
*
*
**
14 ft
4.3 m
DO NOT attach elbow directly to the appliance.
10 ft
3.0 m
*
*
**
20 ft
6.1 m
*H1 and H2 has no specific restrictions EXCEPT,
after V1 = 6 ft, then Ht Max = 2 x V1
**VT + HT = 60 ft Max.
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 4.11
24
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
G. PVK-80 and PVI-SLP Information
This section provides specific detail for installation of
TRUE-36, TRUE-42, and TRUE-50 models with approved power vent kits. Follow instructions included with
the PVK-80 or PVI-SLP power vent kits.
See Table 7.1 below for approved Power Venting options
for TRUE models.
EXHAUST CONTROL LEVER
PVK-80
PVI-SLP
TRUE-36
APPROVED
APPROVED
TRUE-42
APPROVED
APPROVED
TRUE-50
APPROVED
APPROVED
Figure 4.12 PVK-80 Control Lever Adjustment - Open
Table 4.1
WARNING! Risk of Fire! Use ONLY Hearth & Home
Technologies-approved power venting systems with this
appliance. Use of power venting systems not approved
by Hearth & Home Technologies may cause fireplace to
overheat.
The power vent draft flow must be adjusted and set per
the specifications in Table 4.2. Refer to the instructions
provided with the PVK-80 and PVI-SLP for more specific
information.
INDICATOR BAR
ADJUSTMENT BOLT
PVK-80: The exhaust control lever reduces the draft as it
is opened. Open the exhaust control lever to FULL OPEN.
See Figure 4.12. Secure the exhaust control lever to the
power vent housing with the sheet metal screw.
Note: When using a PVK-80 only, the PVK80-PLUS
Kit must be installed by a qualified service technician.
Contact your dealer to order.
Figure 4.13 Baffle Adjustment Location - PVI-SLP
INDICATOR BAR
ADJUSTMENT HOLES
PVI-SLP: The baffle adjustment is measured using the
holes on the indicator bar of the PVI-SLP baffle. This bar
raises as the baffle is opened and lowers as the baffle is
closed. Adjust the baffle by turning the screw located in
the motor enclosure. See Figure 4.13 and 4.14.
WARNING! Risk of Explosion! Follow instructions to
set draft flow. Incorrect setting may impair burner performance and/or cause delayed ignition.
Figure 4.14 Baffle Adjustment - PVI-SLP
PVK-80
Exhaust Control
Lever
PVI-SLP
Baffle Adjustment
Setting
TRUE-36
FULL OPEN
3 Holes Visible
TRUE-42
FULL OPEN
3 Holes Visible
TRUE-50
FULL OPEN
3 Holes Visible
Table 4.2
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
25
5
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
Non-Combustible Wall Penetration
WARNING! Risk of Fire! Maintain air space clearance
to vent. DO NOT pack insulation or other combustibles:
If the hole being penetrated is surrounded by non-combustible materials such as concrete, a hole with diameter
one inch greater than the pipe is acceptable.
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
Failure to keep insulation or other material away from
vent pipe may cause overheating and fire.
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
‡DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
‡,IZDOOWKLFNQHVVLVOHVVWKDQLQWKHH[LVWLQJKHDWVKLHOGVPXVWEHILHOGWULPPHG,I
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
DO NOT PACK WITH
INSULATION OR OTHER
MATERIAL
‡,IZDOOWKLFNQHVVLVOHVVWKDQWKHH[LVWLQJKHDWVKLHOGVPXVWEHILHOGWULPPHG
,IZDOOWKLFNQHVVLVJUHDWHUWKDQLQD'93+60%ZLOOEHUHTXLUHG
(DVP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
10 in.
LQPP
clearance around
vertical sections
12 in.
B
LQPP
clearance
bottom & sides
Wall
Shield
Firestop
A*
WALL
Figure 5.1 Horizontal Venting Clearances To Combustible
Materials
B. Wall Penetration Framing/Firestops
Combustible Wall Penetration
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
MODEL
TRUE-36 NG/LP
TRUE-42 NG
TRUE-42 LP
TRUE-50 NG/LP
A*
74-3/16 in.
79-3/16 in.
91-3/16 in.
83-3/16 in.
B
73-3/16 in.
78-3/16 in.
90-3/16 in.
82-3/16 in.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
* Shows center of vent framing hole with minimum vertical for top venting. The
center of the hole is one (1) in. (25.4 mm) above the center of the horizontal
vent pipe.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section
12.A.) attached to them.
Figure 5.2 Wall Penetration
• See Section 7.E. for information for regarding the installation of a horizontal termination cap.
26
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
C. Ceiling Firestop/Floor Penetration Framing
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 5.3).
ATTIC ABOVE
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
A
• The ceiling firestop may be installed above or
below the ceiling joists when installed with an
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 5.4.
• Secure with three fasteners on each side.
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
A
PIPE
A
DVP
10 in. (254 mm)
D. Install Attic Insulation Shield
WARNING! Fire Risk. DO NOT allow loose
materials or insulation to touch vent. Hearth
& Home Technologies requires the use of an
attic shield.
The International Fuel Gas Code requires an
attic shield constructed of 26 gauge minimum
steel that extends at least 2 in. (51 mm) above
insulation.
• Attic insulation shields must meet specified
clearances to combustible materials and be
secured in place.
• An attic insulation shield kit is available from
Hearth & Home Technologies. Contact your
dealer to order. Install attic insulation shield
according to instructions included with kit.
Figure 5.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
CEILING FIRESTOP
INSTALLED BELOW CEILING
CEILING FIRESTOP
INSTALLED ABOVE CEILING
Figure 5.4 Installing the Attic Shield
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
27
E. Installing the Optional Heat-Zone® Gas
Kit
• Locate the Heat-Zone® ports on the left and right sides of
the appliance. See Figure 5.6. Remove the knockouts
from the appliance with a tin snips.
• Center the duct collar around the exposed hole and
attach it to the appliance with 3 screws. Note: Do this
BEFORE final positioning of the appliance.
• Determine the location for the air register/fan housing
assembly.
Reference the Heat-Zone® Gas Kit instructions for the
remaining installation steps.
HEAT ZONE® LOCATION
LEFT AND RIGHT SIDES
Figure 5.6 Heat Zone Cover Plate
28
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
6
Appliance Preparation
A. Vent Collar Preparation
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
SEAL CAP
NOTICE: This appliance is top vented ONLY.
1. Remove shrink wrap from appliance. Figure 6.1 shows
the shipping location of the seal cap and heat shields
(Section 6), splatter guard and finishing templates
(Section 10), and the logs and Teco-Sil (Section 11).
2. Remove seal cap from top of appliance by removing
one screw, which is included, to prevent construction
material from getting into appliance. Remove seal cap
when pipe installation phase begins. See Figure 6.2.
3. Ensure gasket seal is in place prior to installing vent
pipe sections. Gasket is installed at the factory.
GASKET
Figure 6.2 Seal Cap and Gasket Location
LOGS
SEAL CAP
FINISHING
TEMPLATES
SPLATTER GUARD
HEAT SHIELDS
TECO-SIL
Figure 6.1 Shipping Location of Components
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
29
B. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air space clearance may cause
overheating and fire.
Figure 6.3 Side Nailing Tab in Shipping Position
Nailing tabs are provided on the appliance and on the heat
shields to secure the appliance to the framing members.
See Figure 6.3 and Figure 6.5 for location of nailing tabs
in shipping position.
• Bend out side nailing tabs 90 degrees. See Figure 6.4.
• Place the appliance into position.
• Keep side nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
• Position and install heat shields by securing two screws
in each heat shield. See Figure 6.1 for shipping location
of heat shields. The heat shield screws can be found
pre-installed on the top of the appliance.
• Bend the top header heat shields upward to position
them vertically and bend out the two nailing tabs on the
top of each header heat shield. Secure to framing. See
Figure 6.5.
Figure 6.4 Nailing Tab Bent Out for Installation
HEAT SHIELD NAILING
TAB IN SHIPPING
POSITION
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
Figure 6.5. Heat Shields and Nailing Tabs in Installation Position
30
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
C. Installing Non-Combustible Facing Material
WARNING! Risk of Fire!
• Follow these instructions exactly.
• Facing materials must be installed properly to prevent
fire.
• No materials may be substituted without authorization
by Hearth & Home Technologies.
PERIMETER:
SECURE TO FRAMING WITH
DRYWALL SCREWS OR NAILS
(NOT INCLUDED)
• The finishing templates are shipped fastened to the top
surround. Remove finishing templates prior to installing
non-combustible board.
• Remove non-combustible facing pieces from back of
appliance. See Figure 6.6.
• Install non-combustible facing material to the appliance
using the screws supplied in the manual bag assembly.
• Center and attach two top boards to the framing
members. See Figure 6.7.
• Attach left and right side pieces to framing members.
INTERIOR:
SECURE WITH
SELF-TAPPING SCREWS
(IN MANUAL BAG ASSEMBLY)
• Use fasteners from fastener packet (in manual bag) for
screws that secure to the fireplace. See Figure 6.7.
• Use regular sheetrock screws or nails to secure the
perimeter of the non-combustible facing materials to the
wood framing. See Figure 6.7.
• Use a wet or dry towel or soft brush to remove dust or
dirt from facing material.
• See Section 10 for finishing materials guidelines.
Figure 6.7 Installing Non-Combustible Facing Material
Figure 6.6 Shipping Location of Non-Combustible Board
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
31
7
Venting and Chimneys
A. Assemble Vent Sections
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs
will face toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end of the starting collar.
• Inner pipe over inner collar.
• Push the pipe section until all lanced tabs snap in place.
• Lightly tug on pipe to confirm it has locked.
Required Commercial, Multi-family (Multi-level exceeding
two stories), or High-Rise Applications
Figure 7.1 High Temperature Silicone Sealant
All outer pipe joints must be sealed with 100% silicone
(300º F minimum continuous exposure rating), including
the slip section that connects directly to the horizontal termination cap.
A
Lances
• Apply a bead of silicone sealant (300º F minimum continuous exposure rating) inside the female outer pipe
joint prior to joining sections. See Figure 7.1.
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
B
Figure 7.3
Figure 7.2
Note: Make sure that the seams are not aligned to prevent
unintentional disconnection.
Assemble Pipe Sections
Per Figure 7.2:
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
CORRECT
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
For 90º and 45º elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
32
INCORRECT
Figure 7.4 Seams
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
B. Secure the Vent Sections
C. Disassemble Vent Sections
• Vertical runs originating off the top of the appliance, with
no offsets, must be supported every 8 ft. (2.44 m) after
the maximum allowed 25 ft. (7.62 m) of unsupported rise.
• Rotate either section (see Figure 7.7) so the seams on
both pipe sections are aligned as shown in Figure 7.8.
• Pull carefully to separate the pieces of pipe.
• Vertical runs originating off the rear of the appliance, or
after any elbow, must be supported every 8 ft. (2.44 m).
• Horizontal runs must be supported every 5 feet (1.52
m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support vent sections. See Figures 7.5
and 7.6.
• Wall shield firestops may be used to provide horizontal
support to vent sections.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 7.7 Rotate Seams for Disassembly
120º
Figure 7.8 Align and Disassemble Vent Sections
Figure 7.5 Securing Vertical Pipe Sections
120º
Figure 7.6 Securing Horizontal Pipe Sections
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
33
D. Vertical Termination Requirements
Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 7.9) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 7.10.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Figure 7.10
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Assemble and Install Storm Collar
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
•
•
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................ 2.5*
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
Slide the storm collar onto the exposed pipe section
and align brackets.
Insert a bolt (provided) through the brackets and install
nut. Do not completely tighten.
Figure 7.11 insert Bolt into Brackets
* 3 foot minimum in snow regions
Figure 7.9 Minimum Height From Roof To Lowest Discharge
Opening
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
•
Slide the assembled storm collar down the pipe section
until it rests on the roof flashing. See Figure 7.11.
•
Tighten nut and make sure the collar is tight against the
pipe section.
•
Caulk around the top of the storm collar. See Figure 7.12.
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 7.10.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
34
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of
the cap into the outer flue of the pipe. See Figure 7.12.
Termination Cap
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
Install Horizontal Termination Cap
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
(1 of 3)
Screws
Storm
Collar
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 4 of this manual.
Caulk
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
Figure 7.12
E. Horizontal Termination Requirements
Heat Shield Requirements for Horizontal
Termination
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit
and HRC caps are available. When penetrating a brick
wall, a brick extension kit is available for framing the brick.
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 7.13).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
WALL SHIELD
FIRESTOP
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 7.13.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm, the heat
shields on the cap and wall shield firestop must be
trimmed. A minimum 1-1/2 in. (38 mm) overlap MUST
be maintained.
• Use an extended heat shield if the finished wall
thickness is greater than 7-1/4 in. (184 mm).
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
SLIP SECTION
CAN BE EXTENDED
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 7.13 Venting through the wall
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
35
8
Electrical Information
A. General Information
Junction Box Installation
WARNING! Risk of Shock or Explosion! DO NOT wire
110-120 VAC to the valve or to the appliance wall switch.
Incorrect wiring will damage controls.
The electrical junction box can be accessed three ways
during installation:
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• Remove two screws to release junction box bracket
from the access plate. See Figure 3.2 and Figure
8.2.
• Wire the appliance junction box to unswitched 110120 VAC. This is required for proper operation of the
appliance.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
• Low voltage and 110-120 VAC voltage cannot be shared
within the same wall box.
ACCESS THROUGH LEFT COLUMN
(Prior to installation of non-combustible board)
1. Through the side electrical access:
2. Through the front left column (behind the factoryinstalled non-combustible board):
• From inside remove one screw that secures junction
box to junction box bracket. See Figure 8.1 and
Figure 8.2.
3. Through the firebox:
• From inside remove one screw that secures junction
box to junction box bracket. See Figure 8.1 and
Figure 8.2.
•
Pull the electrical wires from outside the appliance
through the opening into the valve compartment and
secure wires with a Romex connector. See Figure 8.2
•
Make all necessary wire connections to the junction
box/receptacle and reattach the junction box/receptacle
to the outer shell.
ACCESS THROUGH FIREBOX
(After installation of non-combustible board)
GASKET
COVER
Figure 8.1 Junction Box Access
36
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
NOTICE: DO NOT wire
110-120 VAC to wall switch.
Romex
Connector
HT
WHT B
LK
BLK
W
14/2WG
GRN wire
inside box
Copper ground
attached to GRN
screw with GRN wire
Figure 8.2 Junction Box Detail
Accessories Requirements
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
• Hearth & Home Technologies recommends that IntelliFireTM Plus wireless controls be used for their features
and functionality with the IntelliFireTM Plus ignition system.
Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with
type 105º C rated wire. Wire must have high temperature
insulation.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
37
B. Wiring Requirements
Intellifire™ Plus Ignition System Wiring
• Wire the appliance junction box to 110-120 VAC for
proper operation of the appliance.
WARNING! Risk of Shock or Explosion! DO NOT wire
IPI controlled appliance junction box to a switched circuit.
Incorrect wiring will override IPI safety lockout.
• Refer to Figure 8.3, IPI Wiring Diagram.
• This appliance is equipped with an IntelliFire™ Plus
control valve which operates on a 6 volt/1.5 AMP system.
• Plug the 6 volt transformer plug into the appliance junction
box to supply power to the unit OR install 4 AA cell
batteries (not included) into the battery pack before use.
NOTICE: Batteries should only be used as a power source
in the event of an emergency power outage. Batteries
should not be used as a primary long-term power source.
Battery polarity must be correct when installing batteries.
When using batteries as a power source, the 6-volt
transformer must be unplugged from the receptacle.
Do not store batteries in the battery pack when the
appliance is powered by the 6 volt transformer connected
to permanent electrical service.
FLAME
SENSE
RC300 4.5V DC
(AAA X 3)
IGNITER
TO JUNCTION
BOX (110V)
MODULE
I
AUX300 MODULE
ORANGE
S
WHITE
FLAME
MODULATION
AUX 1
AUX2 NOT USED
PROTECTIVE COVER INCLUDED
AUX 2
TO JUNCTION
BOX 110VAC
BATTERY PACK
6V DC
ORANGE
(PILOT)
GREEN
(MAIN)
RED
BLACK
BROWN
LED CONTROL
GROUND
BLACK/RED
BLACK/RED
REAR ACCENT LIGHTING (X 2)
Figure 8.3 IPI Wiring Diagram
38
FRONT EMBER LIGHTING (X 3)
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
9
Gas Information
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 3 for location of gas line
access in appliance.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
• Gas line may be run through knockout(s) provided.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
• Pressure requirements are:
Gas Pressure
• The gap between supply piping and gas access hole
may be caulked with caulk with a minimum of 300ºF
continuous exposure rating or stuffed with noncombustible, unfaced insulation to prevent cold air
infiltration.
Natural Gas
Propane
Minimum inlet pressure
5.0 in. w.c.
11.0 in. w.c.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Maximum inlet pressure
10.0 in. w.c.
13.0 in. w.c.
• A small amount of air will be in the gas supply lines.
Manifold pressure
3.5 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in. (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Check with your local gas utility to determine proper
orifice size.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
39
E. Air Shutter Setting
Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter
is pre-set at the factory for minimum vertical, maximum
horizontal vent run for this appliance: 2 ft. vertical and 7
in. horizontal).
Factory Pre-Set Air Shutter Settings
MODEL
NG
LP
TRUE-36
1/2 in.
Full Open
TRUE-42
11/16 in.
Full Open
TRUE-50
5/8 in.
Full Open
Natural Gas (NG) installations:
As a general rule, it is acceptable to reduce the shutter
opening to adjust for vertical vent pipe sections prior to
the initial fire up.
•
Vertical Termination: May reduce shutter setting by 1/8 in.
•
Horizontal Termination (more than 4 ft. vertical in vent
configuration: May reduce shutter setting by 1/8 in.
•
Horizontal Termination (less than 4 ft vertical in vent
configuration: May reduce shutter setting by 1/16 in.
Propane (LP) installations
•
It is recommended that the air shutter on propane
appliances remain at full open position.
Air Shutter Adjustment
Adjustment can be made to the air shutter with or without
the logs installed with a ¼ in. nut driver. See Figure 1.
Figure 1. Air Shutter Location
To adjust air shutter:
•
Loosen the screw on the burner assembly.
•
To close the air shutter, turn shutter clockwise.
•
To open air shutter, turn shutter counterclockwise.
•
Tighten the screw.
NOTICE: Flames should not appear orange or stretch to
the top refractory. If sooting occurs, provide more air by
opening the air shutter.
Shutter Setting Verification / Flame Appearance
•
After 15 minutes, the flames will be a yellow/blue mix.
The front flames may be blue at this time.
•
After 30 minutes, the flames should be yellow with
some blue flames near the burner ports.
•
After 1 hour, the flame will be at is maximum maturity.
Note: Visually, a propane flame may differ from a
natural gas flame. This is due to the different chemical
compositions that make up both fuel types. In general, the
LP flames may be a little shorter and much brighter than
a natural gas flame.
2282-901
40
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
10
Finishing
A. Facing Material
• Metal front faces may be covered with non-combustible
materials only.
• Facing and/or finishing materials must not interfere
with air flow through louvers, operation of louvers or
decorative fronts, or access for service.
• Facing and/or finishing materials must never overhang
into the glass opening.
• Observe all clearances when applying combustible
materials.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of decorative fronts and
louvers.
COMBUSTIBLE MATERIAL
0 IN.
A
0 IN.
B
0 in.
MODEL
NON-COMBUSTIBLE
BOARD
A
B
in.
mm
in.
mm
TRUE-36
61
1549
57-5/8
1464
TRUE-42
67
1702
62-5/8
1591
TRUE-50
75
1905
66-5/8
1692
Figure 10.1 Non-combustible Facing Diagram
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
41
B. Finishing Templates
Two side finishing templates and one top finishing
template are supplied with the appliance. Refer to the
decorative front instructions for template removal.
3/4 IN.
INSIDE FIT Method: The finishing template pieces are
required for installations that require more than one inch
thick finishing materials to be installed over the face of the
factory-supplied 1/2 inch non-combustible board. Refer
to section 10.D for more information.
OVERLAP Method: The supplied templates are not
required for finishing materials less than one inch thick.
The required decorative front will overlap finish materials
less than one inch thick. Refer to section 10.D for more
information. Remove template by removing the the two top
screws and two screws on each side. The glass assembly
will need to be removed to access the side screws. Follow
the glass removal instructions in Section 11.
Figure 10.3 Left and Right Side Finishing Template Bends
TOP FINISHING
TEMPLATE
Arch Decorative Front Application:
If an arch
decorative front option is chosen, an Arch Template
Kit is required to be installed prior to the installation of
the decorative finishing materials. This kit includes new
finishing templates (3) and arch corner fill pieces (2).
Contact your dealer to order the correct Arch Template Kit
for your fireplace model.
SIDE FINISHING
TEMPLATES
Figure 10.4 Top and Side Finishing Template Locations
Note: For Firesceen Fronts (denoted with “FS”), a thin
layer of mortar may be applied over the visible noncombustible board between finishing material and the
fireplace opening.
1-1/4 IN.
TAB
Figure 10.2 Top Finishing Template Bend
42
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Figure 10.5 Finishing Template Bends
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
43
C. Mantel and Wall Projections
Non-Combustible Zone
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of non-combustible materials (i.e., steel studs, concrete board, etc.).
When installing a mantel, provisions must be made
in order to secure the mantel to the adjacent framing
materials. For example, lintel brackets or lag bolts may
be considered for this purpose.
2 X 4 FRAMING
MATERIAL
1/2 IN. BUILDING MATERIAL
(MAY BE COMBUSTIBLE)
PIPE IS FOR VISUAL
REFERENCE ONLY
NO COMBUSTIBLES
IN HATCHED AREA
1 IN.
Combustible Mantel Legs or Wall Projections
39 IN.
1/2 IN. BUILDING MATERIAL
COMBUSTIBLE
COLUMN
4 IN. MAX.
FACTORY-SUPPLIED
NON-COMBUSTIBLE
BOARD
FACTORY-SUPPLIED
1/2 IN.
NON-COMBUSTIBLE
BOARD
7 IN.
MIN.
14 IN. MIN.
FIREPLACE
OPENING
= COMBUSTIBLES
NOT ALLOWED
COMBUSTIBLE OR
NON-COMBUSTIBLE WALL
Figure 10.6 Combustible Mantel Leg and Wall Projections
Figure 10.8 Non-Combustible Zone
Non-Combustible Mantel Legs or Wall Projections
1/2 IN. BUILDING MATERIAL
NON-COMBUSTIBLE
COLUMN
6 IN. MAX.
FACTORY-SUPPLIED
NON-COMBUSTIBLE
BOARD
SEE SECTION 10.D
FOR REQUIRED
CLEARANCES
14 IN. MIN.
FIREPLACE
OPENING
COMBUSTIBLE OR
NON-COMBUSTIBLE
WALL
Figure 10.7 Non-Combustible Mantel Leg and Wall Projections
44
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Combustible Mantel Projections
Non-Combustible Mantel Projections
1/2 IN.
NON-COMBUSTIBLE
MATERIAL
1/2 IN.
NON-COMBUSTIBLE
MATERIAL
Note: All measurements in inches.
Note: Measurement is taken
from bottom of appliance.
Measurement from
fireplace opening to
bottom of appliance:
= 35-3/16 IN. (TRUE36)
= 40-3/16 IN. (TRUE42)
MAX.
Note:All measurements in inches.
Note: Measurement is taken
from bottom of appliance.
12
9
6
Measurement from fireplace
opening to bottom of appliance:
= 35-3/16 IN. (TRUE36)
= 40-3/16 IN. (TRUE42)
63
3
1
MAX.
12
10
61
58
MIN.
6
60
57
TRUE36
TRUE42
FIREPLACE
OPENING
MIN.
TRUE36
TRUE42
FIREPLACE
OPENING
54
1-1/4 IN.
51
Figure 10.9 Combustible Mantel Allowance - TRUE-36, TRUE-42
Figure 10.11 Non-Combustible Mantel Allowance - TRUE-36, TRUE-42
Combustible Mantel Projections
Non-Combustible Mantel Projections
12
9
Note: All measurements in inches.
Note: Measurement is taken from
bottom of appliance.
TRUE50
MAX.
12
10
6
3
68
1
65
62
59
56
FIREPLACE
OPENING

1/2 IN.
NON-COMBUSTIBLE
MATERIAL
Figure 10.10 Combustible Mantel Allowance - TRUE-50
Note:All measurements in inches.
Note:Measurement is taken from
bottom of appliance.
Measurement from fireplace
opening to bottom of appliance:
= 44-3/16 IN. (TRUE50)
65
6
62
MIN.
TRUE50
FIREPLACE
OPENING
1-1/4 IN.

1/2 IN.
NON-COMBUSTIBLE
MATERIAL
Measurement from fireplace
opening to bottom of appliance:
= 44-3/16 IN. (TRUE50)


Figure 10.12 Non-Combustible Mantel Allowance - TRUE-50
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
45
D. Decorative Front Dimensions for Finishing
A decorative front is required for this appliance. Only decorative fronts certified for use with this appliance model
may be used. Contact your dealer for a list of decorative
fronts that may be used. Once you have determined what
kind of decorative front and finishing material is going to
be used on the fireplace, you may use the table below
which shows the decorative front models and the finishing material thickness allowed. For an inside fit there is an
available template to ensure that proper decorative front
clearances are maintained with finishing material with
thickness greater than 1 inch.
COMBUSTIBLE MATERIAL
B
C (ARCH)
A
FIRESCREEN FRONTS
RECTANGULAR
ARCHED*
FS-36
FS-36A*
FS-42
FS-42A*
FS-50
FS-50A*
DIMENSIONS
FORGE-36
FORGE-36A*
A
FORGE-42
FORGE-42A*
B
1-1/4 IN.
FORGE-50A*
C
1-1/4 IN.
FORGE-50
3/4 IN.
*Requires Arch Template Kit (not included)
Table 10.1. Approved Decorative Fronts
Figure 10.13 Inside Fit Decorative Fronts
The decorative fronts approved for use with this appliance have been designed to be installed by two methods:
Overlap Fit or Inside Fit. Before beginning the installation,
it is important to determine with method will be used.
Overlap Fit Method: These decorative fronts have been
designed to be installed over finishing material up to one
inch thick.
Inside Fit Method: These decorative fronts may be recessed into non-combustible finishing material up to 6
inches thick.
NOTICE: Proper clearances from the fireplace opening
to any finishing material thicker than 1 inch MUST be
maintained.
NOTE: Finishing templates are included with this product.
See Section 10.B.
46
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
11
Appliance Setup
A. Fixed Glass Assembly
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
CAUTION! Risk of Injury! Glass assembly installation
and removal must be performed by a qualified service
technician. See chart below for glass assembly weights.
• TRUE-42 AND TRUE-50 MODELS: It is recommended that Glass installation and removal be performed
by two qualified service technicians.
TRUE-36
32 lbs
Glass Weights
TRUE-42
41 lbs
TRUE-50
54 lbs
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation. Sheet metal
edges are sharp.
Figure 11.2. Glass Clip Tool Location
2. To disengage bottom glass clips, position the glass
clip removal/installation tool parallel to the floor and
insert it about two inches into the gap between the
glass frame and the front bottom fireplace lip. Insert
the tool on the lower left side of the glass clip and
move to the right to engage the clip. Using one motion, pull out slightly while pushing down to disengage
bottom glass clip. Repeat for the other bottom spring
clips. There are three on the TRUE-36 and four on the
TRUE-42 and TRUE-50. See Figure 11.2 and Figure
11.3.
Removing Fixed Glass Assembly
This fixed glass assembly is held in place by lower glass
clips, side clips and top retaining rail. To remove clips, engage the spring clips with the tool and pull tool out slightly.
1. The glass clip removal/installation tool is fastened to
the lower right corner of the appliance. Remove tool
by removing one screw. See Figure 11.1. If glass clip
removal tool becomes misplaced, a cotter pin removal
tool may be used.
NOTICE: Protect and prevent the hearth from damage by
covering it with a drop cloth.
Figure 11.3. Inserting Glass Clip Tool
3. Disengage the left and right glass clips one at a time
using the glass clip removal/installation tool. Insert
tool from the top side of the side glass clip. Pull the
glass tool out slightly to disengage the side clip. See
Figure 11.7.
4. Grasp the left and right sides of the glass assembly
and carefully pull outward to remove the bottom from
the support tabs on the bottom glass clips. Lower the
glass to remove it from the top retainer rail.
CAUTION! Risk of Injury! DO NOT put fingers under
glass frame. Fingers may get pinched by glass frame
during removal.
Figure 11.1. Glass Clip Tool
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
47
Replacing Fixed Glass Assembly
This fixed glass assembly is held in place by two side
clips, one top retaining rail and lower glass clips. The
TRUE36 has three lower glass clips and the TRUE42 and
TRUE50 have four lower glass clips. To remove clips, engage the spring clips with the tool and pull tool out slightly.
Rotate wrist left and right to disengage clip. The glass clip
tool is shown in Figure 11.1.
1. Tool is fastened to the lower right corner of the fireplace. Remove tool by removing one screw. If glass
clip removal tool becomes misplaced, a cotter pin removal tool may be used.
2. Position the fixed glass assembly so that it is about
eight inches from the face of the appliance. See Figure 11.4. An arch decorative front application will require the glass to be installed at a steeper angle.
Once the glass is installed tightly into the top retainer
rail, push in the bottom so that the glass assembly
rests on the support tabs on the glass clip. See Figure 11.6.
GRASP FRAME BY LIP THAT
PROJECTS FROM GLASS. DO NOT
INSERT FINGERS UNDER RAIL.
LIP
RAIL
Figure 11.6. Installing Glass
5. Ensure the fixed glass assembly is situated tight
against the firebox face. Engage the left and right
glass clips using the glass clip tool. See Figure 11.7.
Figure 11.4 Positioning Glass
3. Center the fixed glass assembly from left to right inside the top of the appliance opening.
The glass frame has tabs on the bottom that coincide
with the bottom glass clip location. The TRUE-36 has
three tabs and the TRUE-42 and TRUE-50 have four
tabs. If the glass is not centered, it cannot be installed
properly. Align the notch at the top center of the glass
frame assembly with the notch on the top retaining
rail. See Figure 11.6.
TOP RETAINING RAIL NOTCH
Figure 11.7. Securing Side Glass Clips
6. Once the left and right glass clips are installed, engage the bottom clips by inserting the glass clip tool at
a sharp downward angle to get between the gap between the glass frame and the front bottom fireplace
lip. See Figure 11.8.
7. Return glass tool to its shipping location in the lower right corner of the appliance and secure with one
screw.
GLASS FRAME NOTCH
Figure 11.5 Align Notches
4. Install fixed glass assembly by lifting it up and sliding
it into the top retaining rail. Grasp the fixed glass assembly on the sides.
CAUTION! Risk of Injury! DO NOT put fingers under
glass frame. Fingers may get pinched by glass frame
during installation.
48
Figure 11.8. Securing Bottom Glass Clips
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
B. Remove the Shipping Materials
NOTICE: Do NOT paint the pilot assembly!
Remove shipping materials from inside or underneath
the firebox.
•
The splatter guard is a piece of corrugated material
used to protect the appliance during the installation
process before finishing work on the whole hearth is
complete. Splatter guards may be factory installed
or accompany the decorative front of the unit, depending on the fireplace model. Splatter guards
must be removed before appliance is fired.
WARNING! Risk of Fire! Close the ball valve before installing the splatter guard to prevent accidental lighting.
Remove the splatter guard before lighting the appliance.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
Figure 11.9. Ember Glass Area Covered with Teco-Sil
D. Install Teco-Sil and Mystic Embers
1. Install Teco-Sil along front edge of glass as shown in
Figure 11.8. Rock should follow contour cutout in the
front refractory.
Figure 11.10. Teco-Sil Painted
4. Apply Mystic Embers around the ember bed and
hearth refractory. The joints in the front middle hearth
refractory can be concealed with these embers.
Figure 11.9. Install Teco-Sil
2. Fill in the rest of the ember glass area by placing an
even layer of Teco-Sil across the bottom. Dropping the
Teco-Sil through the oval holes in the burner creates a
more even layer. See Figure 11.9.
3. Using a high temperature black paint, fog the TecoSil to the desired look. See Figure 11.10. Prior to
painting, take precautions to prevent any overspray
from reaching the pilot assembly.
MYSTIC EMBERS
Figure 11.11. Apply Mystic Embers
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
49
E. Glowing Ember Placement
F. LED’s
WARNING! Risk of Explosion! Follow ember placement
instructions in manual. DO NOT place embers directly over
burner ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.
LED’s are factory installed. No additional set up or activation required.
Ember material is shipped with this gas appliance. To place
the ember material:
•
See Owner’s Manual for maintenance and bulb
replacement.
• Embers CANNOT be placed directly over ports. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• Place dime-size pieces of Glowing Embers® just in front
of the port trail, but not on or in between the ports (see
Figure 11.12). Care should be taken so that the ports are
not covered. Failure to follow this procedure will likely
cause lighting and sooting problems.
• Save the remaining ember materials for use during
appliance servicing. The embers provided should be
enough for 3 to 5 applications.
GLOWING EMBERS
Figure 11.12. Location of Glowing Embers
50
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
G. Install the Log Assembly
Note: Refer to Section J for air shutter adjustment instructions.
Log Set Assembly: LOGS-TRUE36
LOGS-TRUE42
Models: TRUE-36C, TRUE-36H, TRUE-36S
TRUE-42C, TRUE-42H, TRUE-42S
LOG PLACEMENT TABS
TRUE-42 ONLY
NOTCH FOR LOG #6
FLAT SPOT FOR LOG #3
1
LOG PLACEMENT NOTCH
Figure 1.
Figure 2.
CAUTION: Logs are fragile, handle with care. Log #1 (2280-701 for TRUE-36, 2281-701 FOR TRUE-42): Locate log
placement notch on the bottom of log #1. See Figure 2. Mate outer notches on the bottom of Log #1 with the left and right grate
tines. Slide Log #1 toward the rear of appliance until back side of Log #1 contacts the log placement tabs. See Figures 1-3.
3
2
BURNED AREA
1
LOG PLACEMENT NOTCH
2
LOG PLACEMENT SLOTS
Figure 3.
Figure 4.
Log #2 (2280-702 for TRUE-36, 2281-702 for TRUE-42): Locate log placement notch on the bottom of Log #2. See Figure
4. Mate notch on the bottom of Log #2 with the center and right grate tines. Slide log toward rear of appliance until right
end contacts the side grate tine. See Figure 5.
Log #2 (TRUE-36 ): Log #2 will be about 1 inch from the
back of the center grate tine when properly placed. See
Figure 5.
Log #2 (TRUE-42 ): Log #2 will contact center log placement
tab on center grate tine. See Figure 5.
LOG CONTACTS
SIDE GRATE TINE
1
NOTCH FOR
LOG #3
2
LEFT SIDE TOWARD REAR
Figure 5.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
51
LOG #5 APPEARANCE
VARIES SLIGHTLY
BETWEEN MODELS
NOTCH
5
1
TOP OF BURNED
AREA NEAR LOG #1
3
4
LEFT
HAND
NOTCH
LOG RESTING IN NOTCH
2
Figure 6.
RIGHT
HAND
NOTCH
Figure 7.
Log #3 (2281-703): Locate log placement notches for Log #3. See Figure 5. Place Log #3 onto notches so that the bottom
of the log rests in the notch on log #2 and the top rests in the left hand side of the notch on Log #1. The top of the burned
area on Log #3 will be close to Log #1 when properly positioned. See Figure 6.
Log #4 (2280-704 for TRUE-36; 2281-704 for TRUE-42): See Figure 7. Place Log #4 between the left and center grate
tines. Notches on log will rest on tines. Log should be positioned as far forward as possible. See Figure 8. Log #4 will
lean against Log #2.
LOG #4 CONTACTS
LOG #2
FLAT AREA
FOR LOG #5
LOG CONTACTS LEFT
SIDE REFRACTORY
LOG POSITIONING
TAB FOR LOG #5
4
5
LOG CONTACTS
CENTER GRATE
TINE
LOG CONTACTS
LEFT GRATE TINE
4
LOG CONTACTS LOG
POSITIONING TAB
Figure 9. Log #5 - TRUE-36.
Figure 8.
Log #5 (2280-705 FOR TRUE-36, 2281-705 FOR TRUE42): Locate flat area on Log #4 that will be used to position
Log #5. See Figure 8. Place Log #5 into appliance as shown
in Figure 9 or Figure 10. Left end of log should rest against
left side refractory just in front of air inlet on rear, lower left
of appliance.
LOG CONTACTS LEFT
SIDE REFRACTORY
REAR GRATE TINE
Log #5 (TRUE-36): Log #5 will sit about halfway between
front and rear grate tines, partially over pilot assembly. Log
#5 will contact log positioning tab as shown in Figure 9. Right
side of Log #5 will rest in notch on Log #4. See Figure 9.
5
Log #5 (TRUE-42): Log #5 will rest against the rear grate
tine as shown in Figure 10. Right side of Log #5 will rest in
notch on Log #4. See Figure 10.
4
FRONT GRATE TINE
Figure 10. Log #5 - TRUE-42
52
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
BURNED
PORTION
6
6
LOG RESTS AGAINST
GRATE TINE
7
NOTCH
(LOG #7 ON TRUE-42 ONLY)
Figure 11.
Figure 12.
Log #6 (2281-706): Place Log #6 into appliance as shown in Figure 12. Base of log will sit on bottom refractory and notch
on log will rest against grate tine. Lean top of log into notch on Log #1. See Figure 2.
NOTCH
BACK TINE
LOG CONTACTS REFRACTORY
8
FRONT TINE
Figure 13.
Figure 14.
Log #7 (2281-707 TRUE-42 ONLY): Place Log #7 into appliance as shown in Figure 13. Right side of log should contact
right refractory and burned portion of log should be centered between front and back tines.
Log #8 (2281-708): Place Log #8 into appliance as shown in Figure 15. Left notch will contact left grate tine and base of log
will rest on bottom refractory.
5
6
8
LOG CONTACTS
GRATE TINE
4
1
6
3
5
2
4
7*
8
*LOG #7 TRUE-42 ONLY
Figure 15.
Figure 16. Log Set Installed.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
2281-935
53
Note: Refer to Section J for air shutter adjustment instructions.
Log Set Assembly: LOGS-TRUE50
LOG PLACEMENT INSTRUCTIONS
Models: TRUE-50C, TRUE-50H, TRUE-50S
NOTCH FOR LOG #6
NOTCH FOR LOG #3
LOG PLACEMENT TABS
1
LOG PLACEMENT NOTCH
Figure 1.
Figure 2.
CAUTION: Logs are fragile, handle with care. Log #1 (2282-701): Locate log placement notch on the bottom of log #1.
See Figure 2. Mate outer notches on the bottom of Log #1 with the left and right grate tines. Slide Log #1 toward the rear
of appliance until back side of Log #1 contacts the log placement tabs shown in Figure 1. See Figure 3.
1
NOTCH FOR 2
BURNED AREA
LOG #4
3
2
NOTCH
Figure 3.
LOG PLACEMENT SLOTS
Figure 4.
Log #2 (2282-702): Locate log placement notches on the bottom of Log #2. See Figure 4. Mate notches on the bottom of
Log #2 as shown in Figure 5. Notch on front of log will contact right front grate tine and notch on right side of log will contact
front inside corner of side grate tine.
NOTCH FOR
LOG #3
NOTCH FOR
LOG #4
FLAT AREA
FOR LOG #3
1
LOG CONTACTS
GRATE TINE
2
Figure 5.
54
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
TOP OF BURNED
AREA NEAR LOG #1
5
1
4
3
2
LOG RESTING IN NOTCH
NOTCH
Figure 6.
Figure 7.
Log #3 (2282-703): Locate log placement areas for Log #3. See Figure 5. Place Log #3 into notch on Log #1 so that the
base rests on the flat area of log #2. The top of the burned area on Log #3 will be close to Log #1 when properly positioned.
See Figure 6.
Log #4 (2282-704): See Figure 7. Place Log #4 between the left and center grate tines. The base of Log #4 should rest on
the refractory. Notch on log will rest on the front left grate tine and the top of log will rest in notch on Log #2. See Figure 8.
LOG RESTS ON LOG #2
LOG RESTS ON PILOT
BRACKET AND LEANS
AGAINST REAR GRATE
TINE
NOTCH FOR LOG #5
LOG RESTS ON LOG #4
4
5
1-3/4 IN.
4
LOG NOTCH
CONTACTS
LEFT GRATE TINE
LOG RESTS ON REFRACTORY
LOG RESTS ON BOTTOM REFRACTORY
Figure 8.
Figure 9.
Log #5 (2281-705): Locate flat area on Log #4 that will be used to position Log #5. See Figure 8. Place Log #5 into appliance as shown in Figure 9. The left side of the log will rest on bottom refractory and pilot bracket. It will also lean against
rear grate tine. The right side of Log #5 will rest in notch on Log #4. There will be a space approximately 1-3/4 inches from
the end of the log to the left side refractory.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
55
LOG RESTS IN NOTCH ON LOG #1
6
6
NOTCH
7
LOG CONTACTS
GRATE TINE
LOG RESTS ON
BOTTOM REFRACTORY
Figure 10.
Figure 11.
Log #6 (2282-706): Place Log #6 into appliance as shown in Figure 11. Base of log will sit on bottom refractory and notch
on log will rest against grate tine. Lean top of log into notch on Log #1. See Figure #2.
REAR GRATE TINE
GROUT LINE #6
GROUT LINE #2
Figure 12.
WIDE END OF LOG
#9 CONTACTS RIGHT
REFRACTORY
Figure 13.
Log #7 (2281-707): Place Log #7 into appliance as shown in Figure 12. The unburned end of the log should rest on the second
grout line from the front edge. The burned end of the log should rest on the sixth grout line. The right side of the log should contact
the refractory on the right side of the firebox.
Log #9 (2170-725): Place Log #9 into appliance as shown in Figure 13. Place log so that the wide end rests on Log #7 and contacts
the refractory on the right side of the firebox just in front of the air intake port. The narrow end of Log #9 should contact the rear of
Log #1 and the middle of Log #9 should contact the rear-right vertical grate tine.
56
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Log #8 (2281-708): Place Log #8 into appliance as shown in Figure 14. Left notch will contact left grate tine and base of log will
rest on bottom refractory.
6
5
LOG CONTACTS
GRATE TINE
3
1
8
9
2
4
7
8
Figure 14.
Figure 15. Log Set Installed (Log #9 not visible in this view).
2282-935B
H. Install Decorative Front
WARNING! Risk of Fire! Install ONLY decorative fronts
approved by Hearth & Home Technologies. Unapproved
decorative fronts may cause fireplace to overheat.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative front.
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
57
12
Reference Materials
A. Vent Components Diagrams
Pipe
Effective
Height/Length
DVP Pipe (see chart)
Effective Length
Inches
Millimeters
DVP4
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
10-7/8 in.
(276 mm)
DVP6A
3 to 6
76 to 152
DVP45 (45º Elbow)
DVP12A
3 to 12
76 to 305
10-1/2 in.
(267 mm)
45 °
4-7/8 in.
(124 mm)
11-3/8 in.
(289 mm)
10 in.
(254 mm)
1 in.
(25 mm)
20-3/4 in.
(527 mm)
7-3/8 in.
(187 mm)
10 in.
(254 mm)
1-1/4 in. (32 mm)
9-1/4 in.
(235 mm)
Tab=1 in.
(25.4 mm)
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
Finished Height: 19-3/4 in./502 mm
UNIV-AS2 (Attic Insulation Shield)
DVP-FS (Ceiling Firestop)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
UP
5 in.
(127 mm)
1 in.
(25 mm)
8 in.
(203 mm)
14 in.
(356 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 12.1 DVP vent components
58
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
A. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
12 in.
(305 mm)
DVP-TRAP
Horizontal Termination Cap
Max
Effective
Length
Trap1
Trap2
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
Figure 12.2 DVP vent components
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
59
A. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(337 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(699 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(337 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
14 in.
(356 mm)
17-3/4 in.
(451 mm)
6 in.
152 mm
12 in.
(305 mm)
DVP-TB1
Basement Vent Cap
DVP-TRAPFL
Flashing
WARNING! Risk of Fire! DO NOT install DVP-TB1 in
application where vinyl siding is present.
11-7/8 in.
(302 mm)
11-5/8 in.
(295 mm)
13-7/8 in.
(352 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
COOL-ADDM
Cap Shield
13-7/8 in.
(352 mm)
9-1/2 in.
(241 mm)
26 in.
660 mm
14 in.
(356 mm)
DVP-HSM-B
Extended Heat Shield
DRC-RADIUS
Cap Shield
Figure 12.3 DVP Vent Components
60
5 in.
(127 mm)
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
A. Vent Components Diagrams (continued)
12 in.
305 mm
9 in.
(229 mm)
2-3/4 in.
(70 mm)
12-1/2 in.
(318 mm)
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
11-1/2 in.
(292 mm)
5-1/4 in.
(133 mm)
12-1/4 in.
(311 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
16 in.
(406 mm)
PVK-80
(Approved for TRUE-36, TRUE-42, TRUE-50.)
(Installation of PVK80-PLUS Kit required )
Optional Wire Harness
13-5/8 IN.
346 mm
EFFECTIVE LENGTH
32 IN. (813 mm) MIN.
35 IN. (889 mm) MAX.
DESCRIPTION
12-1/2 IN.
318 mm
20-3/4 IN.
527 mm
PART NUMBER
10 ft. PV Wire Harness
PVI-WH10
20 ft. PV Wire Harness
PVI-WH20
40 ft. PV Wire Harness
PVI-WH40
60 ft. PV Wire Harness
PVI-WH60
80 ft. PV Wire Harness
PVI-WH80
100 ft. PV Wire Harness
PVI-WH100
Note: Wire harnesses required to power the PVI-SLP
connect to the appliance and are ordered separately from
PVI-SLP. Contact your dealer to order.
Note: Use only approved termination caps with the
PVI-SLP. See instructions included with PVI-SLP kit.
PVI-SLP
Power Vent Inline
16 IN.
406 mm
4-1/2 IN.
114 mm
15 IN.
(381 mm)
9-3/16 IN.
(233 mm)
13-5/8 IN.
(346 mm)
12-1/2 IN.
(318 mm)
16-11/16 IN.
424 mm
16-11/16 IN.
(424 mm)
SLP-LPC
SLP Low Profile Cap
Figure 12.4 DVP vent components
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
61
B. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Remote Controls, Wall Controls and Wall
Switches
Follow the instructions supplied with the control installed
to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
Optional Heat-Zone® Gas Kit
Follow the instruction supplied with the kit for operation.
• Preparation for installation of Heat-Zone® Gas Kit is
discussed in Section 5.E.
See your dealer if you have questions.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
Printed in U.S.A. - Copyright 2015
62
Heat & Glo • TRUE-36, TRUE-42, TRUE-50 Installation Manual • 2282-980 Rev. H • 3/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement