Back Next Applies to Models: 498 Power Procedures Center 489 (-003) Special Tools: none Note Do NOT remove this manual from Product. Installation Step 2: Remove table from skid. Step 1: Remove four 3/8-16 shipping bolts 1 003-1825-00 Rev.C (8/15) Next Installation Step 5: Align holes in backsplash with molded top and secure with five washers and screws. Step 6: Locate clear inlay pad and place into top section with smooth edge down. Step 9: Plug power cord into outlet. Step 3: Remove all loose items from cabinet drawers. Back Step 8: Find appropriate color inserts and installed. Step 4: Lay cabinet on its back. Insert casters and washers as shown. Step 7: Connect foot control. 2 © Midmark Corporation 2008 Next Door Adjustment (perform as necessary) Depth Adjustment... Turn depth screw to move panel front to back. Vertical Adjustment... A) Loosen vertical screw on top and bottom hinge. B) Move door panel up or down. C) Retighten screws. Vertical Screw Depth Screw Horizontal Screw Horizontal Adjustment... Turn horizontal screw to move panel side to side. Adjust door if necessary... Recommended gap is 1/16in. (1.6mm). 3 © Midmark Corporation 2008 Next Operation To adjust Pressure up / down... A) Turn pressure switch ON. B) Pull knob on control panel out and depress footswitch labeled Pressure. C) Turn knob counterclockwise to decrease pressure and clockwise to increase pressure. D) Adjust pressure before using on a patient. E) Push knob back in until a snapping sound is heard, when correctly adjusted. Equipment Alert Motors will overheat if equipment is continuously operated. Vacuum control... A) Turn vacuum switch ON. B) Press left side of footswitch until vacuum procedure is complete. Equipment Alert DO NOT adjust pressure knob completely closed, motors will overheat. Adjust Pressure prior to using Pressure control... A) Turn pressure switch ON. B) Press right side of footswitch until pressure procedure is complete. 4 © Midmark Corporation 2008 Next Maintenance Step 2: Remove hoses from canister. Step 1: Turn OFF power switch. (O) Hose Bracket Step 4: Remove thumb screws and motor cover from cart. Note: Pull bottom of cover up to release from clips in back of cart. Step 5: Remove hose from pump. A) B) C) D) E) Equipment Alert The vacuum canister must be emptied when 3/4 full. Failure to do so will result in serious damage to vacuum pump. Step 3: Remove canister and empty if needed. 5 Place new hose onto pump. Put motor cover back in position. Be sure to secure bottom lip of cover under cart clips in back of cart. Secure cover with thumb screws. Place canister in position. Reattach hose from pump to canister and hose from hose bracket to canister. © Midmark Corporation 2008 Next Maintenance Cleaning External Surfaces... Wipe external surfaces with a clean damp cloth and a mild soap/water solution. Note: This cart has two circuit breakers located on the back of the cart (see illustration). If electrical outlet have no power... Check circuit breaker. If necessary, press button to reset. For Front Outlet For Back Outlet Outlet Outlet Caution Failure to perform a periodic inspection on electrical components may result in personal injury or equipment damage. Power System Maintenance... A) Turn OFF power switch and unplug cart. B) Inspect electrical cords, they should be free of cuts or damage and clear from moving parts. C) Midmark recommends professional inspection every six months. 6 © Midmark Corporation 2008 Next Warranty Information SCOPE OF WARRANTY Midmark Corporation (“Midmark”) warrants to the original retail purchaser that it will repair or replace components of the domestic and international medical products manufactured by Midmark (except for components not warranted under “Exclusions”) that are defective in material or workmanship under normal use and service. Midmark’s obligation under this warranty is limited to the repair or replacement, at Midmark’s option, of the applicable components. This limited warranty shall only apply to defects that are reported to Midmark within the applicable warranty period and which, upon examination by Midmark, prove to be defective. This warranty extends only to the first retail purchaser of a product and is not transferable or assignable. APPLICABLE WARRANTY PERIOD The applicable warranty period, measured from the date of delivery to the original user, shall be one (1) year for all warranted products and components. OBTAINING WARRANTY SERVICE Warranty service must be obtained through either Midmark or an authorized dealer in the Midmark product line for which warranty service is requested. Midmark may be contacted for warranty service inquiries or issues via email at www.midmark.com; by phone at 1-800-MIDMARK; by facsimile at 1-800-365-8631; or by mail to Midmark Corporation, 60 Vista Drive, Versailles, Ohio 45380. It is the retail purchaser’s obligation to arrange for delivery of a product to Midmark or one of its authorized dealers for warranty service, which delivery shall be at retail purchaser’s expense. It is also the retail purchaser’s obligation to comply with the warranty service instructions provided either by Midmark or its authorized dealer. The retail purchaser must provide Midmark with completed warranty registration information within thirty (30) days after purchase in order to obtain the benefits of this warranty. EXCLUSIONS This warranty does not cover, and Midmark shall not be liable, for the following: (1) defects, damage or other conditions caused, in whole or in part, by misuse, abuse, negligence, alteration, accident, freight damage, tampering or failure to seek and obtain repair or replacement in a timely manner; (2) products which are not installed, used, and properly cleaned and maintained as required in the Midmark “Installation” and/or “Installation/Operation Manual” for the applicable product; (3) products considered to be of a consumable nature; (4) accessories or parts not manufactured by Midmark; (5) charges by anyone for adjustments, repairs, replacement parts, installation or other work performed upon or in connection with such products which are not expressly authorized in writing in advance by Midmark; (6) costs and expenses of routine maintenance and cleaning; and (7) representations and warranties made by any person or entity other than Midmark. EXCLUSIVE REMEDY; CONSEQUENTIAL DAMAGES DISCLAIMER: MIDMARK’S ONLY OBLIGATION UNDER THIS WARRANTY IS THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS. MIDMARK SHALL NOT BE LIABLE FOR AND HEREBY DISCLAIMS ANY DIRECT, SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES OR DELAYS, INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS OR INCOME, LOSS OF USE, DOWNTIME, COVER AND EMPLOYEE OR INDEPENDENT CONTRACTOR WAGES, PAYMENTS AND BENEFITS. NO AUTHORIZATION No person or firm is authorized to create or approve for Midmark any other obligation or liability in connection with the products. WARRANTY DISCLAIMER THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS. STATUTE OF LIMITATIONS No action may be brought against Midmark for breach of this limited warranty, an implied warranty, if any, or for any other claim arising out of or relating to the products, more than ninety (90) days following expiration of the limited warranty period. Midmark Corporation 60 Vista Drive Versailles, OH 45380-0286 Phone: 937-526-3662 Fax: 937-526-5542 midmark.com 7 © Midmark Corporation 2008
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021