APC | NBRK0550 | Installation guide | APC NBRK0550 Installation guide

Installation Guide
NetBotz®
Wireless Temperature Sensor
NBWS100T
NBWS100H
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Document overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Additional documentation . . . . . . . . . . . . . . . . . . . . . . . . . 1
Supported appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Supported devices on the NetBotz wireless network . . . . 3
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Components of the Wireless Sensor Network. . . . . . . . . . . . . . . 6
Adding the Wireless Temperature Sensor to the Network . . . . . 7
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
LED behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Configuring the Wireless Temperature Sensor . . . . . . . . . . . . . . 9
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Configuring a Wireless Temperature Sensor . . . . . . . . . . 9
Sensor listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mounting the Wireless Temperature Sensor . . . . . . . . . . . . . . . 10
Magnetic installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cable tie installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wall bracket installation . . . . . . . . . . . . . . . . . . . . . . . . . 11
Configuring and Monitoring Sensors . . . . . . . . . . . . . . . . . . . . . 11
Receiving and sending data . . . . . . . . . . . . . . . . . . . . . . 11
Using the Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Updating the Wireless Temperature Sensor . . . . . . . . . . . . . . . 12
Replacing the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning the Wireless Temperature Sensor . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Two Year Limited Factory Warranty . . . . . . . . . . . . . . . . . . . . . . 15
Obtaining service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Wireless Temperature Sensor Installation Guide
i
Wireless Temperature Sensor Installation Guide
ii
Introduction
Product description
The NetBotz® Wireless Temperature Sensor connects to a NetBotz wireless
sensor network, allowing you to monitor the temperature (NBWS100T) or the
temperature and humidity (NBWS100H) in your data center.
Warning: The Wireless Temperature Sensor requires a minimum
of BotzWare v4.4 and NetBotz Advanced View v4.4. To upgrade,
use the Upgrade icon in your NetBotz appliance Advanced View,
or visit the APC web site.
ZigBee® Certified. The Wireless Temperature Sensor is ZigBee Certified.
ZigBee is a wireless mesh networking standard for low-power applications.
Schneider Electric is a member of the ZigBee Alliance.
Full information on the ZigBee standard can be found at the ZigBee Alliance
website: http://www.zigbee.org.
Document overview
The NetBotz Wireless Temperature Sensor Installation Guide describes how to
install the Wireless Temperature Sensor, and configure its settings. Specific
instructions on installing other devices on the wireless sensor network are in the
installation instructions for each component.
Additional documentation
Unless otherwise noted, the following documentation is available on the CD
provided with the NetBotz appliance, or on the applicable product page on the
APC Web site, www.apc.com. To quickly find a product page, enter the product
name or part number in the Search field.
NetBotz Appliance User’s Guide – Includes all details for using, managing, and
configuring a NetBotz system with one of the following appliances: NetBotz
Room Monitor 455 (NBWL0455, NBWL0456), NetBotz Rack Monitor 450
(NBRK0450), NetBotz Rack Monitor 550 (NBRK0550), or NetBotz Rack
Monitor 570 (NBRK0570).
NetBotz Wireless Temperature Sensor Installation Guide
1
Supported appliances
The Wireless Temperature Sensor, and the other devices in the wireless sensor
network, are monitored by a single NetBotz appliance. You can connect the
Wireless Temperature Sensor to a wireless sensor network on any of the
following appliances:
• NetBotz Rack Monitor 450 (NBRK0450)
• NetBotz Room Monitor 455 (NBWL0455, NBWL0456)
• NetBotz Rack Monitor 550 (NBRK0550)
• NetBotz Rack Monitor 570 (NBRK0570)
The NetBotz Rack Monitor 450 appliance supports a total of 26 wireless
devices on the wireless sensor network. The NetBotz Room Monitor 455,
NetBotz Rack Monitor 550, and NetBotz Rack Monitor 570 appliances support
a total of 48 wireless devices on the wireless sensor network.
Supported devices on the NetBotz wireless network
The Wireless Temperature Sensor is always configured as an End Device in
your wireless sensor network.
The following wireless devices can be configured as a Coordinator or Router:
Sensor Name
NetBotz USB Coordinator & Router
NetBotz Wireless Sensor Pod 180
Range
Part Number
100 ft line of
sight
100 ft line of
sight
NBWC100U
NBPD0180
The following wireless devices can be configured as an End Device:
Sensor Name
NetBotz Temperature Sensor
NetBotz Wireless Sensor Pod 180
Range
Part Number
100 ft line of
sight
100 ft line of
sight
NBWS100T
NBWS100H
NBPD0180
Warning: Only the devices listed above are compatible with the
Wireless Temperature Sensor. Other devices will not function and
may damage the device.
2
NetBotz Wireless Temperature Sensor Installation Guide
Physical Description







Item
Description
 Covered data port For factory use only
 Reset button
Used to reboot the sensor or reset the sensor to factory defaults
 Side mounting
Used to secure the sensor with tie wraps
slot

Pry slots
Used to separate the case to replace the battery

Status LED
Signifies the current state of the sensor

Rocker switch
Used to turn the sensor on or off

Magnets
Used to mount the sensor

Bottom mounting
slot
Used to secure the sensor with tie wraps
NetBotz Wireless Temperature Sensor Installation Guide
3
Inventory
Inspect the contents of the package to ensure that the parts included match those
shown below. Report missing or damaged contents to Schneider Electric or
your reseller. However, if damage was due to shipping, immediately report the
damage to the shipping agent.
The shipping and packaging materials are recyclable. Please save
them for later use or dispose of them appropriately.







Item
Description

NetBotz Wireless Temperature Sensor

Tie wraps (3)

3/4-in. x 3/4-in. adhesive cable tie holder (2)

Wall-mounting bracket

#8 x 3/4-in Phillips head screws (2)

Plastic wall anchor (2)

Foam adhesive strips (2)
Literature kit (not shown)
4
NetBotz Wireless Temperature Sensor Installation Guide
Components of the Wireless Sensor Network
Wireless Sensor Network. A ZigBee wireless network consisting of a host
appliance, one Coordinator, and one or more devices in Router or End Device
mode.
Host Appliance. A wireless sensor network is monitored by a single NetBotz
appliance, listed in “Supported appliances” on page 2. The appliance collects
data from the wireless sensor network, and generates alerts based on sensor
thresholds.
The host appliance supports a total of 26 or 48 wireless devices on the network,
listed in “Supported devices on the NetBotz wireless network” on page 2.
Coordinator. Each NetBotz host appliance and wireless sensor network must
have one and only one Coordinator. The Coordinator is connected directly to
the host appliance via USB. It reports data from the sensors on the network, and
its internal sensors and any attached external sensors (NBSP0180 only), and
provides firmware updates to the wireless network, when available.
Router. A wireless sensor configured as a Router extends the range of the
wireless sensor network and passes information back and forth from the
NetBotz device to the End Devices.
A wireless sensor network can contain multiple Routers; one Router for every
three racks is recommended.
End Device. An End Device monitors its internal sensors, and any attached
sensors, and sends data back to the monitoring appliance through the network.
The Wireless Temperature Sensor is automatically configured as an End
Device.
NetBotz Wireless Temperature Sensor Installation Guide
5
Adding the Wireless Temperature Sensor to the
Network
Overview
The order in which you power and configure your wireless network is
important.
For best results, power and configure the Coordinator, and any Routers, on your
wireless network before adding the Wireless Temperature Sensor.
Add the Coordinator and Routers to the NetBotz Advanced View.
Add the extended addresses (MAC) of the Coordinator and Routers to the “Add
Addresses” dialog, accessed from the Wireless Sensor Setup task in the
Advanced View.
For information about configuring your wireless sensor network, see the
installation manual that came with the NetBotz Wireless Sensor Pod 180 or the
NetBotz Wireless USB Coordinator & Router.
Add the address of the Wireless Temperature Sensor. You can use a
hand-held USB QR code scanner with document capture capabilities to scan the
extended address (MAC) of the Wireless Temperature Sensor directly into the
“Add Addresses” dialog, accessed from the Wireless Sensor Setup task in the
Advanced View.
Alternatively, you can use any QR code scanner to save a list of MAC addresses
to a text file, one address per line, and copy and paste it into the dialog, or enter
the addresses manually.
Some QR code scanners return the part number, serial number, and MAC
address on one line:
XN:NBWS100T%SN:XXXXXX123456%MAC:00C0B70000XXXXXX.
To add a sensor to your wireless network, enter only the alphanumeric MAC
address of each sensor in the “Add Addresses” dialog in the Advanced View.
Once the addresses have been added to the list, you must click Apply
Commission List to save the list to the NetBotz appliance.
6
NetBotz Wireless Temperature Sensor Installation Guide
Scanning with a USB QR code scanner. When you use a USB QR code
scanner with document capture capabilities, only the extended address (MAC)
of each Wireless Temperature Sensor will appear in the list in Advanced View
in the correct format.
1. Attach a hand-held USB QR code scanner with document capture
capabilities to a computer running the NetBotz Advanced View.
2. With the Advanced View open to the “Add Addresses” dialog in the
Wireless Sensor Setup task, scan the QR code on the label of each
Wireless Temperature Sensor.
3.
Click Apply Commission List to save the list to the NetBotz appliance.
Note: Depending on the appliance, you can add up to 26 or up to
48 wireless devices, including the Coordinator and Routers, to your
wireless sensor network. For more information, see “Supported
devices on the NetBotz wireless network” on page 2.
Mount the sensors. Mount the Wireless Temperature Sensors using the
instructions in “Mounting the Wireless Temperature Sensor” on page 11.
Power the sensors. Turn the Wireless Temperature Sensor on using the
rocker switch on its side.
The sensor will scan all channels, and wait for a response from the Coordinator.
It will then send a request to join the wireless network.
The request to join the network will be accepted or will fail based on whether
the sensor’s extended address (MAC) is in the same list in Advanced View as
the Coordinator, and whether the device limit on your wireless network has
been reached.
Once the request is accepted, the sensor will join the wireless network.
NetBotz Wireless Temperature Sensor Installation Guide
7
LED activity
The LED on the sensor blinks to indicate certain statuses or alerts.
During the boot process, LED activity on the Wireless Temperature Sensor is as
follows:
LED Activity
Flashes a quick green, yellow, red
sequence
Alternately flashes green and yellow for
about 45 seconds
Flashes green three times
Turns solid yellow for 5 seconds
Flashes a quick green, yellow, green
sequence
Meaning
Power on
Runtime check
Check OK
Firmware update check
Ready to attempt to join the network
Note: If the LED flashes red three times, then slowly flashes red,
contact Technical Support.
The following table lists possible LED activity and its meaning:
LED Activity
Flashes yellow twice every 2 seconds
Turns solid green, then turns off
Off
Meaning
Searching for network
Joined the network
• Joined the network
• Has not joined the network, and is
conserving battery power.
To conserve power, the sensor will attempt to join the network after waiting the
following number of seconds: 5, 15, 30, 60, 120, 300, 300, 600, 600, 1200.
If the attempts to rejoin the network fail, the sensor will scan the network every
six hours to re-try the connection. If it cannot join the network after
approximately 24 hours, it will reboot, and attempt to join the network again,
repeating the wait interval starting at 5 seconds, until it joins the network.
To force an attempt to join the network, press the reset button.
8
NetBotz Wireless Temperature Sensor Installation Guide
Using the Reset Button
Overview
The reset button on the side of the Wireless Temperature Sensor is used to
reboot the sensor, or reset the sensor to the factory default settings.
Reboot. When the reset button is given a short press (less than 3 seconds), the
Status LED flashes green, and the sensor reboots with the current settings in
place.
Reset to factory defaults. Press and hold the reset button for at least 5
seconds. The Status LED flashes green, and after about three seconds, changes
to solid red until the button is released. The sensor will reset, erase its current
settings, and restore the factory default settings.
Note: During the initial 45-second startup time, the reset button is
disabled. Once startup is complete, the button functions normally.
NetBotz Wireless Temperature Sensor Installation Guide
9
Monitoring the Wireless Temperature Sensor
Overview
Once your wireless sensor network is installed and receiving power, you can
begin monitoring your system using the software interface for the appliance.
See your appliance installation and quick configuration manual for
system installation details and for instructions on accessing the
software interface of the appliance.
Sensor listing
When a Wireless Temperature Sensor is selected in the Navigation Pane in
Advanced View, the following sensors are listed in the Sensor Pane:
Sensor
Temperature
Humidity
Battery
RSSI
Description
The temperature sensor reading.
The humidity sensor reading (NBWS100H only)
The voltage of the battery.
The Received Signal Strength Indicator. This lists the
strength of the wireless signal between the sensor and the
Router or Coordinator to which it sends data.
A reading above 30% is ideal.
Receiving and sending data
The Coordinator on the wireless sensor network passes data back and forth
between the host appliance and any Routers or End Devices on the wireless
sensor network as necessary.
If there is a change of 1ºC or 1% RH or more, each Wireless Temperature Sensor
sends its own data every 30 seconds. If there is no change, the Wireless
Temperature Sensor waits up to three (3) minutes before sending sensor data to
indicate it is still alive.
The Wireless Temperature Sensor does not extend the wireless network or pass
data to other Wireless Temperature Sensors, or other End Devices on the
network.
10
NetBotz Wireless Temperature Sensor Installation Guide
Updating the Wireless Temperature Sensor
Firmware updates for the Wireless Temperature Sensor are included in the
BotzWare firmware releases. When a BotzWare firmware update is available,
you download it from the APC website and install it on the NetBotz appliance.
Once the BotzWare firmware update is applied, and the Coordinator receives
the firmware update package from the NetBotz appliance, the Wireless
Temperature Sensor receives the update package from the Coordinator over the
wireless network.
When all the devices on the network have received the update package, the
Firmware Update Available button is activated in the Wireless Sensor Setup
task in the Advanced View. You click the button to reboot each Wireless
Temperature Sensor to apply the firmware update.
Mounting the Wireless Temperature Sensor
When planning your installation locations, be sure to place each Wireless
Temperature Sensor within range of a Router or a Coordinator device. The
maximum wireless range of the Wireless Temperature Sensor is 75 ft (line of
sight). This range is a best-case scenario and the signal will be strongly affected
by environmental interference. Use the RSSI sensor reading (available in the
device’s sensor listing in Advanced View) to tune device placement.
To improve connection strength, it is recommended to use a Router in every
third rack to boost reception.
The recommended minimum distance between wireless devices is 2 ft.
Additional information on device placement may be found on the APC
Knowledge Base, http://www.apc.com/support/answers.cfm.
Choose the option below that fits your installation location.
Note: Install the Wireless Temperature Sensor in an environment
compatible with the environmental specifications on page 13.
Magnetic installation
Mount the Wireless Temperature Sensor in the desired location in the rack using
the magnets on its base.
NetBotz Wireless Temperature Sensor Installation Guide
11
Cable tie installation
The Wireless Temperature Sensor ships with a pair of adhesive cable tie holders
and tie wraps used to mount it on a perforated rack door.
To mount the Wireless Temperature Sensor on a rack door:
1.
Place the sensor in the desired location on the rack door.
2. Place the cable tie holders in the desired location on the rack door. Press
until each tie holder is firmly seated.
3. Insert a tie wrap through the mesh grating and into the mounting slots on
one side of the sensor.
4.
Gently tighten the tie wrap.
5.
Repeat steps 3 and 4 on the other side of the sensor, if desired.
Wall bracket installation
The Wireless Temperature Sensor ships with a wall bracket, and screws or foam
adhesive strips, used to mount it outside the rack using the magnets on its base.
Note: To maintain access to the QR code, and to make battery
replacement easier, using the foam adhesive strips directly on the
Wireless Temperature Sensor is not recommended.
Replacing the Battery
The Wireless Temperature Sensor uses a 3V CR2477 battery. Battery life is
estimated at up to 5 years under normal use.
To replace the battery:
1.
Turn the Wireless Temperature Sensor off.
2.
Insert a thin flat screwdriver into a pry slot on the side of the sensor.
3.
Gently twist to open the case.
4.
Carefully remove the board, and slide the spent battery out.
5. Insert the new battery with the + sign facing the bottom of the battery
holder.
6.
Place the board in the cover.
7.
Align the arrows on the base and the cover, and press together to close.
8. Turn the sensor on using the rocker switch on its side, and wait for it to
join the network.
Cleaning the Wireless Temperature Sensor
To clean the device, gently wipe surfaces with a clean, dry cloth.
12
NetBotz Wireless Temperature Sensor Installation Guide
Specifications
Electrical
Input voltage, nominal
3V battery, CR2477 non-rechargeable primary
cell
Maximum total current draw
33mA USB
Physical
Dimensions (H x W x D)
38.0 x 38.0 x 19.8 mm (1.5 x 1.5 x 0.78 in)
Shipping dimensions (H x W x D)
230.0 x 165.0 x 48.0 mm (9.0 x 6.5 x 2.0 in)
Weight
with batteries
with batteries and bracket
0.03kg (0.07 lb)
0.05kg (0.11 lb)
Shipping weight
0.18 kg (0.4 lb)
Environmental
Elevation (above MSL)
Operating
Storage
0 to 3000 m (0 to 10,000 ft)
0 to 15 000 m (0 to 50,000 ft)
Temperature
Operating
Storage
0 to 45ºC (32 to 113°F)
–15 to 65°C (5 to 149°F)
Humidity
Operating
Storage
0 to 95%, non-condensing
0 to 95%, non-condensing
Compliance
Immunity/Emissions
CE, EMC Directive 2004/108/EC,
R&TTE Directive 1999/5/EC,
Canadian ICES-003, US FCC 47 CFR Part 15
NetBotz Wireless Temperature Sensor Installation Guide
13
Two Year Limited Factory Warranty
Schneider Electric IT Corporation (SEIT), warrants its products to be free from
defects in materials and workmanship for a period of two (2) years excluding
the batteries. The SEIT obligation under this warranty is limited to repairing or
replacing, at its own sole option, any such defective products. Repair or
replacement of a defective product or parts thereof does not extend the original
warranty period.
This warranty applies only to the original purchaser who must have properly
registered the product within 10 days of purchase. Products may be registered
online at warranty.apc.com.
SEIT shall not be liable under the warranty if its testing and examination
disclose that the alleged defect in the product does not exist or was caused by
end user’s or any third person’s misuse, negligence, improper installation,
testing, operation or use of the product contrary to SEIT’s recommendations or
specifications. Further, SEIT shall not be liable for defects resulting from: 1)
unauthorized attempts to repair or modify the product, 2) incorrect or
inadequate electrical voltage or connection, 3) inappropriate on site operation
conditions, 4) Acts of God, 5) exposure to the elements, or 6) theft. In no event
shall SEIT have any liability under this warranty for any product where the
serial number has been altered, defaced, or removed.
14
NetBotz Wireless Temperature Sensor Installation Guide
EXCEPT AS SET FORTH ABOVE, THERE ARE NO WARRANTIES,
EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE,
APPLICABLE TO PRODUCTS SOLD, SERVICED OR FURNISHED
UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH.
SEIT DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, SATISFACTION AND FITNESS FOR A
PARTICULAR PURPOSE.
SEIT EXPRESS WARRANTIES WILL NOT BE ENLARGED,
DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR
LIABILITY WILL ARISE OUT OF, SEIT’S RENDERING OF
TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION
WITH THE PRODUCTS.
THE FOREGOING WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND
REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE
SEIT’S SOLE LIABILITY AND PURCHASER’S EXCLUSIVE
REMEDY FOR ANY BREACH OF SUCH WARRANTIES. SEIT
WARRANTIES EXTEND ONLY TO ORIGINAL PURCHASER AND
ARE NOT EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL SEIT, ITS OFFICERS, DIRECTORS,
AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF
INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES,
ARISING OUT OF THE USE, SERVICE OR INSTALLATION OF THE
PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT
OR TORT, IRRESPECTIVE OF FAULT, NEGLIGENCE OR STRICT
LIABILITY OR WHETHER SEIT HAS BEEN ADVISED IN ADVANCE
NetBotz Wireless Temperature Sensor Installation Guide
15
OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, SEIT
IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR
REVENUE, WHETHER DIRECT OR INDIRECT, LOSS OF
EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE,
LOSS OF DATA, COSTS OF SUBSTITUANTS, CLAIMS BY THIRD
PARTIES, OR OTHERWISE.
NOTHING IN THIS LIMITED WARRANTY SHALL SEEK TO
EXCLUDE OR LIMIT SEIT’S LIABILITY FOR DEATH OR
PERSONAL INJURY RESULTING FROM ITS NEGLIGENCE OR ITS
FRAUDULENT MISREPRESENTATION OF TO THE EXTENT THAT
IT CANNOT BE EXCLUDED OR LIMITED BY APPLICABLE LAW.
To obtain service under warranty you must obtain a Returned Material
Authorization (RMA) number from customer support. Customers with
warranty claims issues may access the SEIT worldwide customer support
network through the SEIT Web site: www.apc.com. Select your country from
the country selection drop down menu. Open the Support tab at the top of the
web page to obtain information for customer support in your region. Products
must be returned with transportation charges prepaid and must be accompanied
by a brief description of the problem encountered and proof of date and place of
purchase.
16
NetBotz Wireless Temperature Sensor Installation Guide
Obtaining service
To obtain support for problems with your NetBotz Wireless Temperature
Sensor:
1. Note the serial number. The serial number is printed on the label on the
back of the device.
2. Contact Customer Support using the information on the back cover of
this manual. A technician will try to help you solve the problem by
phone.
3. If you must return the product, the technician will give you a return
material authorization (RMA) number. If the warranty expired, you will
be charged for repair or replacement.
4. Pack the unit carefully. The warranty does not cover damage sustained in
transit. Enclose a letter with your name, address, RMA number and
daytime phone number; a copy of the sales receipt; and a check as
payment, if applicable.
5.
Mark the RMA number clearly on the outside of the shipping carton.
6. Ship by insured, prepaid carrier to the address provided by the Customer
Support technician.
NetBotz Wireless Temperature Sensor Installation Guide
17
18
NetBotz Wireless Temperature Sensor Installation Guide
Radio Frequency Interference
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
USA—FCC
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE
MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
FCC ID: SNSNBWS100
Canada—ICES
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
IC: 3351-NBWS100
European Union
This product’s transmitter is in conformity with the requirements of EU Council Directive
199/5/EC on the approximation of the laws of the Member States relating to Radio and
Telecommunications Terminal Equipment (R&TTE). This product may cause radio
interference in which case the user may be required to take adequate measures.
This product is in conformity with the protection requirements of EU Council Directive 2004/
108/EC on the approximation of the laws of the Member States relating to electromagnetic
compatibility. Schneider Electric cannot accept responsibility for any failure to satisfy the
protection requirements resulting from an unapproved modification of the product.
Schneider Electric IT Worldwide
Customer Support
Customer support for this product is available at no charge in any of the following
ways:
• Visit the SEIT web site to access documents in the Knowledge Base and to
submit customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized web sites for specific countries, each of which provides
customer support information.
– www.apc.com/support/
Global support searching the Knowledge Base and using e-support.
• Contact the Customer Care Center by telephone or e-mail.
– Local, country-specific centers: go to www.apc.com/support/contact for
contact information.
For information on how to obtain local customer support, contact the Schneider Electric
representative or other distributors from whom you purchased your Schneider Electric
product.
© 2014 Schneider Electric. APC, the APC logo, NetBotz, InfraStruxure, and NetShelter are owned by
Schneider Electric Industries S.A.S., or its affiliated companies. All other trademarks are property of their
respective owners.
990-5327A-001
5/2014
Download PDF