Delta | THINKPAD R40 | Technical information | Delta THINKPAD R40 Technical information

IBM Mobile Systems
ThinkPad Computer
Hardware Maintenance Manual
March 2004
This manual supports: ThinkPad R40
Note
Before using this information and the product it
supports, be sure to read the general information
under “Notices” on page 178.
First Edition (March 2004)
The following paragraph does not apply to the United
Kingdom or any country where such provisions are
inconsistent with local law:
INTERNATIONAL BUSINESS MACHINES CORPORATION
PROVIDES THIS PUBLICATION “AS IS” WITHOUT ANY
WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
LIMITED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Some states
do not allow disclaimer or express or implied warranties in
certain transactions; therefore, this statement may not
apply to you.
This publication could include technical inaccuracies or
typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in
new editions of the publication. IBM may make
improvements or changes to the products or the programs
described in this publication at any time.
It is possible that this publication may contain references
to, or information about, IBM products (machines and
programs), programming, or services that are not
announced in your country. Such references or information
must not be construed to mean that IBM intends to
announce such IBM products, programming, or services in
your country.
Requests for technical information about IBM products
should be made to your IBM authorized dealer or your IBM
marketing representative.
© Copyright International Business Machines
Corporation 2004. All rights reserved.
US Government Users Restricted Rights – Use, duplication
or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
About this manual
.
.
.
.
.
.
Introduction . . . . . . . .
Important service information . . . .
Strategy for replacing FRUs . . .
How to use error messages . . .
Diskette compatibility matrix . . . .
Safety notices: multilingual translations .
Safety information . . . . . . .
General safety . . . . . . .
Electrical safety . . . . . .
Safety inspection guide . . . .
Handling devices that are sensitive to
discharge . . . . . . .
Grounding requirements . . . .
Laser compliance statement . . . .
.
.
.
.
. 1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 3
. 3
. 3
. 4
. 4
. 5
. 17
. 17
. 18
. 19
. . . .
. . . .
. . . .
. . . .
electrostatic
. . . . . 20
. . . . . 21
. . . . . 22
General descriptions . . . .
Read this first . . . . . . .
What to do first . . . . .
Related service information . . .
Service web site . . . . .
Restoring the preloaded system
Passwords . . . . . . .
Power management . . . .
Checkout guide . . . . . .
Testing the computer . . . .
Detecting system information with
Power system checkout . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
PC-Doctor .
. . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
25
25
25
28
28
28
30
33
36
36
38
39
ThinkPad R40. . . . . .
Product overview . . . . .
Specifications . . . . .
Status indicators . . . .
FRU tests . . . . . .
Fn key combinations . . .
Symptom-to-FRU index . . .
Numeric error codes . . .
Error messages . . . .
Beep symptoms . . . .
No-beep symptoms . . .
LCD-related symptoms . .
Intermittent problems . . .
Undetermined problems . .
FRU replacement notices . .
Screw notices . . . . .
Retaining serial numbers. .
Removing and replacing a FRU.
1010 Battery pack. . . .
1020 Ultrabay Plus device .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
43
45
45
48
50
52
53
53
56
57
57
58
59
59
60
60
61
63
64
65
© Copyright IBM Corp. 2004
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
iii
1030 Hard-disk drive . . . . . . . . . . 66
1040 DIMM . . . . . . . . . . . . 68
1050 Mini PCI adapter . . . . . . . . . 70
1060 Keyboard . . . . . . . . . . . 73
1070 Backup battery . . . . . . . . . . 81
1080 Optical storage in the fixed bay . . . . . 82
1090 PC Card slot assembly . . . . . . . 85
1100 Hinge cover . . . . . . . . . . . 87
1110 Communication daughter card (CDC) . . . 88
1120 Fan assembly . . . . . . . . . . 94
1130 CPU . . . . . . . . . . . . . 95
1140 Bluetooth antenna assembly . . . . . . 97
1150 LCD assembly . . . . . . . . . . 98
1160 Keyboard bezel . . . . . . . . . 103
1170 Speaker assembly and microphone cable
108
1180 System board . . . . . . . . . . 109
1190 Hard-disk drive slot . . . . . . . . 116
2000 Ultrabay Plus guide rail . . . . . . . 117
2010 I/O Bracket . . . . . . . . . . . 119
2020 LCD front bezel . . . . . . . . . 120
2030 Inverter card . . . . . . . . . . 121
2040 LCD panel and LCD cable assembly . . . 122
2050 Antenna assembly, hinges, and LCD cover
124
Locations . . . . . . . . . . . . . . 127
Front view for 2681, 2682, 2683, 2722, 2723, 2724 127
Rear view for 2681, 2682, 2683, 2722, 2723, 2724 129
Bottom view for 2681, 2682, 2683, 2722, 2723,
2724 . . . . . . . . . . . . . 130
Front view for 2684, 2685 . . . . . . . . 131
Rear view for 2684, 2685 . . . . . . . . 132
Bottom view for 2684, 2685 . . . . . . . 133
Parts list . . . . . . . . . . . . . . 134
R40 series model matrix . . . . . . . . 134
Overall . . . . . . . . . . . . . 144
LCD FRUs . . . . . . . . . . . . 161
Keyboard . . . . . . . . . . . . . 165
Recovery CDs . . . . . . . . . . . 166
Miscellaneous parts . . . . . . . . . . 169
AC adapters . . . . . . . . . . . . 172
Telephone cable . . . . . . . . . . . 173
Optional FRUs . . . . . . . . . . . 174
Common parts list . . . . . . . . . . 176
Notices . . . . . . . . . . . . . . 178
Trademarks . . . . . . . . . . . . 178
iv
ThinkPad R40
About this manual
This manual contains service and reference information for
IBM ThinkPad R40 product. Use this manual along with
the advanced diagnostic tests to troubleshoot problems.
The manual is divided into sections as follows:
v The common sections provide general information,
guidelines, and safety information required in servicing
computers.
v The product-specific section includes service, reference,
and product-specific parts information.
Important
This manual is intended for trained service
personnel who are familiar with ThinkPad products.
Use this manual along with the advanced diagnostic
tests to troubleshoot problems effectively.
Before servicing an IBM ThinkPad product, be sure
to review the safety information under “Safety
notices: multilingual translations” on page 5, “Safety
information” on page 17, and “Laser compliance
statement” on page 22.
© Copyright IBM Corp. 2004
1
2
ThinkPad R40
Introduction
Important service information
Important
BIOS and device driver fixes are
customer-installable. The BIOS and device drivers
are posted on the IBM support site
http://www.ibm.com/pc/support
Advise customers to contact the PC Company
HelpCenter at 800-772-2227 if they need assistance
in obtaining or installing any diskette fixes.
Customers in Canada should call IBM HelpPC at
800-565-3344 for assistance or download
information.
Strategy for replacing FRUs
Before replacing parts
Make sure that all diskette fixes are installed before
replacing any FRUs listed in this manual.
Use the following strategy to prevent unnecessary expense
for replacing and servicing FRUs:
v If you are instructed to replace a FRU but the
replacement does not correct the problem, reinstall
the original FRU before you continue.
v Some computers have both a processor board and a
system board. If you are instructed to replace either the
processor board or the system board, and replacing one
of them does not correct the problem, reinstall that
board, and then replace the other one.
v If an adapter or device consists of more than one FRU,
any of the FRUs may be the cause of the error. Before
replacing the adapter or device, remove the FRUs, one
by one, to see if the symptoms change. Replace only
the FRU that changed the symptoms.
Attention: The setup configuration on the computer you
are servicing may have been customized. Running
Automatic Configuration may alter the settings. Note the
current configuration settings (using the View Configuration
option); then, when service has been completed, verify that
those settings remain in effect.
© Copyright IBM Corp. 2004
3
Important service information
Strategy for replacing a hard-disk drive
Always try to run a low-level format before replacing a
hard-disk drive.
Attention: The drive startup sequence in the computer
you are servicing may have been changed. Be extremely
careful during write operations such as copying, saving, or
formatting. If you select an incorrect drive, data or
programs can be overwritten.
How to use error messages
Use the error codes displayed on the screen to diagnose
failures. If more than one error code is displayed, begin the
diagnosis with the first error code. Whatever causes the
first error code may also cause false error codes. If no
error code is displayed, see if the error symptom is listed
in the Symptom-to-FRU Index for the computer you are
servicing.
Diskette compatibility matrix
The compatibility of each of the drives with the diskettes
for it is as follows:
4
Diskette
drive
Diskette
capacity
Compatibility
3.5-inch
1.0 MB
Read and write
2.0 MB
Read and write
4.0 MB
Not compatible
ThinkPad R40
Safety notices
Safety notices: multilingual translations
In this manual, safety notices appear in English with a
page number reference to the appropriate multilingual,
translated safety notice found in this section.
The following safety notices are provided in English,
French, German, Hebrew, Italian, and Spanish.
Safety notice 1
Before the computer is powered-on after FRU replacement, make
sure all screws, springs, and other small parts are in place and
are not left loose inside the computer. Verify this by shaking the
computer and listening for rattling sounds. Metallic parts or metal
flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement
d’une unité en clientèle, vérifiez que tous les ressorts, vis et
autres pièces sont bien en place et bien fixées. Pour ce faire,
secouez l’unité et assurez-vous qu’aucun bruit suspect ne se
produit. Des pièces métalliques ou des copeaux de métal
pourraient causer un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder
angeschlossen wird, muß sichergestellt werden, daß keine
Schrauben, Federn oder andere Kleinteile fehlen oder im
Gehäuse vergessen wurden. Der Computer muß geschüttelt und
auf Klappergeräusche geprüft werden. Metallteile oder-splitter
können Kurzschlüsse erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la
sostituzione di una FRU, accertarsi che tutte le viti, le molle e
tutte le altri parti di piccole dimensioni siano nella corretta
posizione e non siano sparse all’interno dell’elaboratore. Verificare
ciò scuotendo l’elaboratore e prestando attenzione ad eventuali
rumori; eventuali parti o pezzetti metallici possono provocare
cortocircuiti pericolosi.
(continued)
Introduction
5
Safety notices
(continuation of safety notice 1)
Antes de encender el sistema despues de sustituir una FRU,
compruebe que todos los tornillos, muelles y demás piezas
pequeñas se encuentran en su sitio y no se encuentran sueltas
dentro del sistema. Compruébelo agitando el sistema y
escuchando los posibles ruidos que provocarían. Las piezas
metálicas pueden causar cortocircuitos eléctricos.
6
ThinkPad R40
Safety notices
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and
cadmium. Do not disassemble a standby battery, recharge it,
throw it into fire or water, or short-circuit it. Dispose of the
battery as required by local ordinances or regulations. Use
only the battery in the appropriate parts listing. Use of an
incorrect battery can result in ignition or explosion of the
battery.
Certaines batteries de secours contiennent du nickel et du
cadmium. Ne les démontez pas, ne les rechargez pas, ne les
exposez ni au feu ni à l’eau. Ne les mettez pas en
court-circuit. Pour les mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la pile de
sauvegarde ou celle de l’horloge temps réel, veillez à
n’utiliser que les modèles cités dans la liste de pièces
détachées adéquate. Une batterie ou une pile inappropriée
risque de prendre feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem
Diskettenlaufwerk befindet, kann geringe Mengen Nickel und
Cadmium enthalten. Sie darf nur durch die Verkaufsstelle
oder den IBM Kundendienst ausgetauscht werden. Sie darf
nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer
oder Wasser ausgesetzt werden. Die Batterie kann schwere
Verbrennungen oder Verätzungen verursachen. Bei der
Entsorgung die örtlichen Bestimmungen für Sondermüll
beachten. Beim Ersetzen der Bereitschafts-oder
Systembatterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien
kann zu Entzündung oder Explosion führen.
(continued)
Introduction
7
Safety notices
(continuation of safety notice 2)
Alcune batterie di riserva contengono una piccola quantità di
nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco
o nell’acqua né cortocircuitarle. Smaltirle secondo la
normativa in vigore (DPR 915/82, successive disposizioni e
disposizioni locali). Quando si sostituisce la batteria dell’RTC
(real time clock) o la batteria di supporto, utilizzare soltanto i
tipi inseriti nell’appropriato Catalogo parti. L’impiego di una
batteria non adatta potrebbe determinare l’incendio o
l’esplosione della batteria stessa.
Algunas baterías de reserva contienen una pequeña cantidad
de níquel y cadmio. No las desmonte, ni recargue, ni las
eche al fuego o al agua ni las cortocircuite. Deséchelas tal
como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería
no apropiada puede provocar la ignición o explosión de la
misma.
8
ThinkPad R40
Safety notices
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not
disassemble it, throw it into fire or water, or short-circuit it.
Dispose of the battery pack as required by local ordinances
or regulations. Use only the battery in the appropriate parts
listing when replacing the battery pack. Use of an incorrect
battery can result in ignition or explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne
l’exposez ni au feu ni à l’eau. Ne la mettez pas en
court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la
batterie, veillez à n’utiliser que les modèles cités dans la liste
de pièces détachées adéquate. En effet, une batterie
inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht
zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder
Wasser ausgesetzt werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim Ersetzen der
Batterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien
kann zu Entzündung oder Explosion führen.
La batteria contiene piccole quantità di nichel. Non
smontarla, gettarla nel fuoco o nell’acqua né cortocircuitarla.
Smaltirla secondo la normativa in vigore (DPR 915/82,
successive disposizioni e disposizioni locali). Quando si
sostituisce la batteria, utilizzare soltanto i tipi inseriti
nell’appropriato Catalogo parti. L’impiego di una batteria non
adatta potrebbe determinare l’incendio o l’esplosione della
batteria stessa.
(continued)
Introduction
9
Safety notices
(continuation of safety notice 3)
Las baterías contienen pequeñas cantidades de níquel. No
las desmonte, ni recargue, ni las eche al fuego o al agua ni
las cortocircuite. Deséchelas tal como dispone la normativa
local. Utilice sólo baterías que se encuentren en la lista de
piezas al sustituir la batería. La utilización de una batería no
apropiada puede provocar la ignición o explosión de la
misma.
10
ThinkPad R40
Safety notices
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a
severe burn. Do not recharge it, remove its polarized
connector, disassemble it, heat it above 100°C (212°F),
incinerate it, or expose its cell contents to water. Dispose of
the battery as required by local ordinances or regulations.
Use only the battery in the appropriate parts listing. Use of
an incorrect battery can result in ignition or explosion of the
battery.
La pile de sauvegarde contient du lithium. Elle présente des
risques d’incendie, d’explosion ou de brûlures graves. Ne la
rechargez pas, ne retirez pas son connecteur polarisé et ne
la démontez pas. Ne l’exposez pas à une temperature
supérieure à 100°C, ne la faites pas brûler et n’en exposez
pas le contenu à l’eau. Mettez la pile au rebut conformément
à la réglementation en vigueur. Une pile inappropriée risque
de prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich
entzünden, explodieren oder schwere Verbrennungen
hervorrufen. Batterien dieses Typs dürfen nicht aufgeladen,
zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf
ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der
zur richtigen Polung angebrachte Verbindungsstecker
entfernt werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim Ersetzen der
Batterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien
kann zu Entzündung oder Explosion führen.
(continued)
Introduction
11
Safety notices
(continuation of safety notice 4)
La batteria di supporto e una batteria al litio e puo
incendiarsi, esplodere o procurare gravi ustioni. Evitare di
ricaricarla, smontarne il connettore polarizzato, smontarla,
riscaldarla ad una temperatura superiore ai 100 gradi
centigradi, incendiarla o gettarla in acqua. Smaltirla secondo
la normativa in vigore (DPR 915/82, successive disposizioni e
disposizioni locali). L’impiego di una batteria non adatta
potrebbe determinare l’incendio o l’esplosione della batteria
stessa.
La batería de repuesto es una batería de litio y puede
provocar incendios, explosiones o quemaduras graves. No la
recargue, ni quite el conector polarizado, ni la desmonte, ni
caliente por encima de los 100°C (212°F), ni la incinere ni
exponga el contenido de sus celdas al agua. Deséchela tal
como dispone la normativa local.
12
ThinkPad R40
Safety notices
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your
eyes or on your hands, immediately wash the affected areas with
water for at least 15 minutes. Seek medical care if any symptoms
from the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous
recevez dans les yeux ou sur les mains une partie du fluide,
rincez-les abondamment pendant au moins quinze minutes.
Consultez un médecin si des symptômes persistent après le
lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei
der Entsorgung die örtlichen Bestimmungen für Sondermüll
beachten. Der LCD-Bildschirm besteht aus Glas und kann
zerbrechen, wenn er unsachgemäß behandelt wird oder der
Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist
und die darin befindliche Flüssigkeit in Kontakt mit Haut und
Augen gerät, sollten die betroffenen Stellen mindestens 15
Minuten mit Wasser abgespült und bei Beschwerden
anschließend ein Arzt aufgesucht werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso
contenuto entrasse in contatto con gli occhi o le mani, lavare
immediatamente le parti interessate con acqua corrente per
almeno 15 minuti; poi consultare un medico se i sintomi
dovessero permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto
con sus ojos o sus manos, lave inmediatamente las áreas
afectadas con agua durante 15 minutos como mínimo. Obtenga
atención medica si se presenta algún síntoma del fluido despues
de lavarse.
Introduction
13
Safety notices
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects
the lower part of the inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le
cache en plastique protégeant la partie inférieure de la carte
d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den
unteren Teil der Spannungswandlerplatine umgibt, nicht
entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in
plastica che avvolge la parte inferiore della scheda
invertitore.
Para evitar descargas, no quite la cubierta de plástico que
rodea la parte baja de la tarjeta invertida.
14
ThinkPad R40
Safety notices
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or
grounded battery can produce enough current to burn
personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé,
le court-circuit ou la mise à la masse d’une batterie peut
produire suffisamment de courant pour brûler des matériaux
combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben,
können sie doch bei Kurzschluß oder Erdung genug Strom
abgeben, um brennbare Materialien zu entzünden oder
Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio,
una batteria in corto circuito o a massa può fornire corrente
sufficiente da bruciare materiali combustibili o provocare
ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una
batería cortocircuitada o con contacto a tierra puede
producir la corriente suficiente como para quemar material
combustible o provocar quemaduras en el personal.
Introduction
15
Safety notices
Safety notice 8
DANGER
Before removing any FRU, power off the computer, unplug all
power cords from electrical outlets, remove the battery pack,
and then disconnect any interconnecting cables.
Avant de retirer une unité remplaçable en clientèle, mettez le
système hors tension, débranchez tous les cordons
d’alimentation des socles de prise de courant, retirez la
batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der
Steckdose gezogen, der Akku entfernt und alle
Verbindungskabel abgenommen sein, bevor eine FRU
entfernt wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema,
scollegare dalle prese elettriche tutti i cavi di alimentazione,
rimuovere la batteria e poi scollegare i cavi di
interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe
todos los cables de las tomas de corriente eléctrica, quite la
batería y, a continuación, desconecte cualquier cable de
conexión entre dispositivos.
16
ThinkPad R40
Safety information
Safety information
The following section presents the safety information that
you need to be familiar with before servicing an IBM
mobile computer.
General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the
machines during and after maintenance.
v When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between
your feet.
3. Use a slow lifting force. Never move suddenly or
twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg
muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any
object that weighs more than 16 kg (35 lb) or objects
that you think are too heavy for you.
v Do not perform any action that causes hazards to the
customer, or that makes the equipment unsafe.
v Before you start the machine, ensure that other service
representatives and the customer’s personnel are not in
a hazardous position.
v Place removed covers and other parts in a safe place,
away from all personnel, while you are servicing the
machine.
v Keep your toolcase away from walk areas so that other
people will not trip over it.
v Do not wear loose clothing that can be trapped in the
moving parts of a machine. Make sure that your sleeves
are fastened or rolled up above your elbows. If your hair
is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or
fasten it with a nonconductive clip, approximately 8
centimeters (3 inches) from the end.
v Do not wear jewelry, chains, metal-frame eyeglasses, or
metal fasteners for your clothing.
Attention: Metal objects are good electrical
conductors.
v Wear safety glasses when you are hammering, drilling,
soldering, cutting wire, attaching springs, using solvents,
or working in any other conditions that might be
hazardous to your eyes.
Introduction
17
Safety information
v After service, reinstall all safety shields, guards, labels,
and ground wires. Replace any safety device that is
worn or defective.
v Reinstall all covers correctly before returning the
machine to the customer.
Electrical safety
Observe the following rules when working on electrical
equipment.
Important
Use only approved tools and test equipment. Some
hand tools have handles covered with a soft
material that does not insulate you when working
with live electrical currents.
Many customers have, near their equipment, rubber
floor mats that contain small conductive fibers to
decrease electrostatic discharges. Do not use this
type of mat to protect yourself from electrical shock.
v Find the room emergency power-off (EPO) switch,
disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or
unplug the power cord quickly.
v Do not work alone under hazardous conditions or near
equipment that has hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
v Before you start to work on the machine, unplug the
power cord. If you cannot unplug it, ask the customer to
power-off the wall box that supplies power to the
machine and to lock the wall box in the off position.
v If you need to work on a machine that has exposed
electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the
power-off controls, is near you.
Attention: Another person must be there to switch
off the power, if necessary.
– Use only one hand when working with powered-on
electrical equipment; keep the other hand in your
pocket or behind your back.
Attention: An electrical shock can occur only when
there is a complete circuit. By observing the above
rule, you may prevent a current from passing through
your body.
18
ThinkPad R40
Safety information
– When using testers, set the controls correctly and
use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if
necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work
with very high voltages; these instructions are in the
safety sections of maintenance information. Use
extreme care when measuring high voltages.
v Regularly inspect and maintain your electrical hand tools
for safe operational condition.
v Do not use worn or broken tools and testers.
v Never assume that power has been disconnected from
a circuit. First, check that it has been powered off.
v Always look carefully for possible hazards in your work
area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges,
and missing safety grounds.
v Do not touch live electrical circuits with the reflective
surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and
machine damage.
v Do not service the following parts with the power on
when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct
grounding of the units.)
v If
–
–
–
an electrical accident occurs:
Use caution; do not become a victim yourself.
Switch off power.
Send another person to get medical aid.
Safety inspection guide
The purpose of this inspection guide is to assist you in
identifying potentially unsafe conditions. As each machine
was designed and built, required safety items were
installed to protect users and service personnel from injury.
This guide addresses only those items. You should use
good judgment to identify potential safety hazards due to
attachment of non-IBM features or options not covered by
this inspection guide.
Introduction
19
Safety information
If any unsafe conditions are present, you must determine
how serious the apparent hazard could be and whether
you can continue without first correcting the problem.
Consider these conditions and the safety hazards they
present:
v Electrical hazards, especially primary power (primary
voltage on the frame can cause serious or fatal
electrical shock)
v Explosive hazards, such as a damaged CRT face or a
bulging capacitor
v Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe
conditions, use the following checklist at the beginning of
every service task. Begin the checks with the power off,
and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or
sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition.
Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external
ground pin and frame ground.
b. The power cord should be the type specified in the
parts list.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious non-IBM alterations. Use good
judgment as to the safety of any non-IBM alterations.
6. Check inside the unit for any obvious unsafe
conditions, such as metal filings, contamination, water
or other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws
or rivets) have not been removed or tampered with.
Handling devices that are sensitive to
electrostatic discharge
Any computer part containing transistors or integrated
circuits (ICs) should be considered sensitive to electrostatic
discharge (ESD.) ESD damage can occur when there is a
difference in charge between objects. Protect against ESD
20
ThinkPad R40
Safety information
damage by equalizing the charge so that the machine, the
part, the work mat, and the person handling the part are all
at the same charge.
Notes
1. Use product-specific ESD procedures when they
exceed the requirements noted here.
2. Make sure that the ESD protective devices you
use have been certified (ISO 9000) as fully
effective.
When handling ESD-sensitive parts:
v Keep the parts in protective packages until they are
inserted into the product.
v Avoid contact with other people.
v Wear a grounded wrist strap against your skin to
eliminate static on your body.
v Prevent the part from touching your clothing. Most
clothing is insulative and retains a charge even when
you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a
static-free work surface. The mat is especially useful
when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below,
to provide protection that meets the specific service
requirement.
Note
The use of a grounding system is desirable but
not required to protect against ESD damage.
– Attach the ESD ground clip to any frame ground,
ground braid, or green-wire ground.
– Use an ESD common ground or reference point
when working on a double-insulated or
battery-operated system. You can use coax or
connector-outside shells on these systems.
– Use the round ground-prong of the AC plug on
AC-operated computers.
Grounding requirements
Electrical grounding of the computer is required for
operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a
certified electrician.
Introduction
21
Laser compliance statement
Laser compliance statement
Some IBM Personal Computer models are equipped from
the factory with an optical storage device such as a
CD-ROM drive or a DVD-ROM drive. They are also sold
separately as options. The drive is certified in the U.S. to
conform to the requirements of the Department of Health
and Human Services 21 Code of Federal Regulations
(DHHS 21 CFR) Subchapter J for Class 1 laser products.
Elsewhere, the drive is certified to conform to the
requirements of the International Electrotechnical
Commission (IEC) 825 and CENELEC EN 60 825 for
Class 1 laser products.
22
ThinkPad R40
Laser compliance statement
When a CD-ROM drive, DVD drive or the other laser
product is installed, note the following:
CAUTION:
Use of controls or adjustments or performance of procedures
other than those specified herein might result in hazardous
radiation exposure.
O uso de controles, ajustes ou desempenho de
procedimentos diferentes daqueles aqui especificados pode
resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez
les consignes de réglage et d’utilisation des commandes,
ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier
festgesetzt verwendet, kann gefährliche Laserstrahlung
auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure
diverse da quelle specificate possono provocare
l’esposizione a.
El uso de controles o ajustes o la ejecución de
procedimientos distintos de los aquí especificados puede
provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, DVD-ROM drive or the other
optical storage device could result in exposure to
hazardous laser radiation. There are no serviceable parts
inside those drives. Do not open.
Introduction
23
Laser compliance statement
Some CD-ROM drives, DVD-ROM drives, or other optical
storage devices contain an embedded Class 3A or Class
3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not
stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de
luz, não olhe diretamente por meio de instrumentos óticos e
evite exposição direta com o feixe de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le
faisceau, de le regarder directement avec des instruments
optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über
optische Instrumente in den Laserstrahl sehen und den
Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel,
se optikai eszközökkel. Kerülje a sugárnyalábbal való
érintkezést !.
Aprendo l’unità vengono emesse radiazioni laser. Non fissare
il fascio, non guardarlo direttamente con strumenti ottici e
evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con
instrumental óptico el haz de luz. Evite la exposición directa
al haz.
24
ThinkPad R40
General descriptions
This chapter includes descriptions for any ThinkPad model
that has the PC-Doctor DOS diagnostics program. Some
descriptions might not apply to your particular computer.
Read this first
Before you go to the checkout guide, be sure to read this
section.
Important notes
v Only certified trained personnel should
service the computer.
v Read the entire FRU removal and replacement
page before replacing any FRU.
v Use new nylon-coated screws when you
replace FRUs.
v Be extremely careful during such write
operations as copying, saving, or formatting.
Drives in the computer that you are servicing
sequence might have been altered. If you select
an incorrect drive, data or programs might be
overwritten.
v Replace FRUs only for the correct model.
When you replace a FRU, make sure the model
of the machine and the FRU part number are
correct by referring to the FRU parts list.
v A FRU should not be replaced because of a
single, unreproducible failure. Single failures
can occur for a variety of reasons that have
nothing to do with a hardware defect, such as
cosmic radiation, electrostatic discharge, or
software errors. Consider replacing a FRU only
when a problem recurs. If you suspect that a
FRU is defective, clear the error log and run the
test again. If the error does not recur, do not
replace the FRU.
v Be careful not to replace a nondefective FRU.
What to do first
When you do return a FRU, you must include the following
information in the parts exchange form or parts return form
that you attach to it:
__ 1. Name and phone number of servicer
__ 2. Date of service
__ 3. Date on which the machine failed
© Copyright IBM Corp. 2004
25
Read this first
__ 4. Date of purchase
__ 5. Failure symptoms, error codes appearing on the
display, and beep symptoms
__ 6. Procedure index and page number in which the
failing FRU was detected
__ 7. Failing FRU name and part number
__ 8. Machine type, model number, and serial number
__ 9. Customer’s name and address
Note for warranty:
During the warranty period, the customer may be
responsible for repair costs if the computer damage was
caused by misuse, accident, modification, unsuitable
physical or operating environment, or improper
maintenance by the customer. The following list provides
some common items that are not covered under warranty
and some symptoms that might indicate that the system
was subjected to stress beyond normal use.
Before checking problems with the computer, determine
whether the damage is covered under the warranty by
referring to the following:
The following are not covered under warranty:
v LCD panel cracked from the application of excessive
force or from being dropped
v Scratched (cosmetic) parts
v Distortion, deformation, or discoloration of the cosmetic
parts
v Cracked or broken plastic parts, broken latches, broken
pins, or broken connectors caused by excessive force
v Damage caused by liquid spilled into the system
v Damage caused by the improper insertion of a PC Card
or the installation of an incompatible card
v Damage caused by foreign material in the diskette drive
v Diskette drive damage caused by pressure on the
diskette drive cover or by the insertion of a diskette with
multiple labels
v Damaged or bent diskette eject button
v Fuses blown by attachment of a nonsupported device
v Forgotten computer password (making the computer
unusable)
v Sticky keys caused by spilling a liquid onto the keyboard
The following symptoms might indicate damage
caused by nonwarranted activities:
v Missing parts might be a symptom of unauthorized
service or modification.
26
ThinkPad R40
Read this first
v If the spindle of a hard-disk drive becomes noisy, it may
have been subjected to excessive force, or dropped.
General descriptions
27
Related service information
Related service information
This section provides information about the following:
v “Service web site”
v “Restoring the preloaded system”
v “Passwords” on page 30
v “Power management” on page 33
Service web site
When the latest maintenance diskette and the system
program service diskette become available, a notice will be
posted on http://www.ibm.com/pc/partner/infotips
Restoring the preloaded system
If the data on a hard-disk drive is damaged or accidentally
erased, you can restore the software that was shipped with
the computer. This software includes the pre-installed
operating system, applications, and device drivers.
To restore the pre-installed software, you can use either
the Product Recovery program or a recovery CD.
Ordering the recovery CD
When the hard-disk drive is replaced because of a
failure, no Product Recovery program is on the new
hard disk. In this case, you must use the Product
Recovery CD for the computer. Order the recovery
CD and the hard-disk drive at the same time so that
you can recover the new hard-disk drive with the
pre-installed software when they arrive. For
information on which CD to order, see “Recovery
CDs” on page 166
The Product Recovery program is in the service partition, a
section of the hard-disk drive that is not displayed by
Windows Explorer.
Attention: All of the files on the primary hard-disk
partition (usually drive C) will be lost in the recovery
process. Be sure to back up copies of the files you have
saved on your drive C before you begin.
Product Recovery program
If your hard disk drive data is damaged or accidentally
erased, you can restore the software that was shipped with
your computer. This software includes your pre-installed
operating system, applications, and device drivers.
You can restore your pre-installed software using the
Product Recovery program.
28
ThinkPad R40
Related service information
The Product Recovery program is in a section of your hard
disk drive that is not displayed by Windows Explorer.
Note: The recovery process might take up to 2 hours.
Attention
All of the files on the primary hard disk
partition (usually drive C) will be lost in the
recovery process. Be sure to back up copies
of the files you have saved on your drive C
before you begin.
To use the Product Recovery program to restore your
pre-installed software, do the following:
1. If possible, save all your files and shut down your
operating system.
2. Turn off your computer.
3. Turn on your computer. Watch the display carefully.
When the following message is displayed, press the
blue Access IBM button to open the Access IBM
Predesktop Area: “To interrupt normal startup, press
the blue Access IBM button.” (If Windows is not
running normally and does not open, the Access IBM
Predesktop Area will open automatically.)
4. Double-click the Recover to factory contents.
5. Follow the instructions on the screen.
6. When the Product Recovery program finishes, your
computer will restart and begin the configuration
process.
Using the recovery CD
To create the service partition and install the preloaded
system from the recovery CD, do the following:
To create the service partition:
1. Erase all partitions on the hard-disk drive, using FDISK
or a similar application.
2. Boot with the recovery CD (and the boot diskette if
required.)
3. Following message is displayed: “Your computer
originally included a Product Recovery program ...
Reinstall the Product Recovery program? (Y/N) [ ]”.
Note: If the hard-disk drive contains any partitions, you
do not receive this message; go to step 1.
4. Press Y key. The service partition is created and
loaded with the Product Recovery program files.
General descriptions
29
Related service information
Note: If you do not want to create the service partition,
press N key, and then go to step 8.
5. At next window, press Enter to continue.
v The service partition is created. The system
automatically reboots during this process.
v The recovery process copies some files to the
service partition, and PKUNZIPs others.
v Follow the prompts. You may be prompted to
change CDs.
v When the process is complete, the system reboots.
Continue to step 6 to install preloaded system.
Install preloaded system from CD:
6. Boot with the recovery CD (and the boot diskette if
required.)
7. If the hard-disk drive is blank, the following message
is displayed: “Your computer originally included a
Product Recovery program ... Reinstall the
Product Recovery program? (Y/N) [ ]”.
v To install the service partition, go to step 4.
v To preload the hard-disk drive without installing the
service partition, press N key.
8. If you get a message asking which operating system
to install, select the proper operating system and
press Enter.
9. A message is displayed: “Full Recovery:”. Press
Enter to select.
10. On each of the next three windows, press the Y key.
11. Follow the prompts to complete the recovery.
Passwords
As many as three passwords may be needed for any
ThinkPad computer: the power-on password (POP), the
hard-disk password (HDP), and the supervisor password
(SVP).
If any of these passwords has been set, a prompt for it
appears on the screen whenever the computer is turned
on. The computer does not start until the password is
entered.
Exception: If only an SVP is installed, the password
prompt does not appear when the operating
system is booted.
30
ThinkPad R40
Related service information
Power-on password:
A power-on password (POP) protects the system from
being powered on by an unauthorized person. The
password must be entered before an operating system can
be booted.
Hard-disk password:
There are two hard-disk passwords (HDPs):
v User HDP—for the user
v Master HDP—for the system administrator, who can use
it to get access to the hard disk even if the user has
changed the user HDP
Note: There are two modes for the HDP: User only and
Master + User. The Master + User mode requires
two HDPs; the system administrator enters both in
the same operation. The system administrator then
provides the user HDP to the system user.
Attention: If the user HDP has been forgotten, check
whether a master HDP has been set. If it has, it can be
used for access to the hard-disk drive. If no master HDP is
available, IBM does not provide any services to reset
either the user or the master HDP, or to recover data from
the hard-disk drive. The hard-disk drive can be replaced
for a scheduled fee.
Supervisor password:
A supervisor password (SVP) protects the system
information stored in the IBM BIOS Setup Utility. The SVP
must be entered in order to get access to the IBM BIOS
Setup Utility and make changes to system configuration
settings.
Attention: If the SVP has been forgotten and cannot be
made available to the servicer, there is no service
procedure to reset the password. The system board must
be replaced for a scheduled fee.
How to remove the power-on password
To remove a POP that you have forgotten, do the
following:
(A) If no SVP has been set:
1. Turn off the computer.
2. Remove the battery pack.
For how to remove the battery pack, see “1010 Battery
pack” on page 64.
3. Remove the backup battery.
For how to remove the backup battery, see “1070
Backup battery” on page 81.
General descriptions
31
Related service information
4. Turn on the computer and wait until the POST ends.
After the POST ends, the password prompt does not
appear. The POP has been removed.
5. Reinstall the backup battery and the battery pack.
(B) If an SVP has been set and is known by the servicer:
1. Turn on the computer by pressing and holding F1.
2. Enter the SVP. The IBM BIOS Setup Utility menu
appears.
3. Select Security, using the cursor keys to move down
the menu.
4. Select Password.
5. Select Power-On Password.
6. At the Enter Current Password field, enter the SVP.
7. When the Enter New Password field opens, leave it
blank and press Enter twice.
8. In the Changes have been saved window, press Enter.
9. Press F10; then, in the Setup confirmation window,
select Yes .
How to remove the hard-disk password
Attention: If User only mode is selected and the user
HDP has been forgotten and cannot be made available to
the servicer, IBM does not provide any services to reset
the user HDPs or to recover data from the hard-disk drive.
The hard-disk drive can be replaced for a scheduled fee.
To remove a user HDP that has been forgotten, when the
SVP and the master HDP are known, do the following:
1. Power on the computer by pressing and holding F1.
2. Enter the SVP. The IBM BIOS Setup Utility menu
appears.
3. Select Security, using the cursor keys to move down
the menu.
4. Select Password.
5. Select Hard-disk x password, where x is the letter of
the hard-disk drive. A pop-up window opens.
6. Select Master HDP.
7. Enter the master HDP; then leave the New Password
field blank and press Enter twice.
8. Press F10.
9. Select Yes in the Setup Configuration window.
Both user HDP and master HDP will have been
removed.
32
ThinkPad R40
Related service information
Power management
To reduce power consumption, the computer has three
power management modes: screen blank, standby, and
hibernation.
Notes
v Screen blank mode is called standby mode in
Windows 95 and Windows NT.
v Standby mode is called suspend mode in
Windows 95 and Windows NT.
Screen blank mode
Screen blank mode has three variants, as follows:
1. If you press Fn+F3, or the time set on the “LCD off
timer” in IBM BIOS Setup Utility expires,
v The LCD backlight turns off.
v The hard-disk drive motor stops.
v The speaker is muted.
2. If you are using the ACPI operating system and you
press Fn+F3,
v The LCD backlight turns off.
v The hard-disk drive motor stops.
3. If the time set on the “Turn off monitor” timer in the
operating system expires,
v The LCD backlight turns off.
To end screen blank mode and resume normal operation,
press any key.
Standby mode
When the computer enters standby mode, the following
events occur in addition to what occurs in screen blank
mode:
v The LCD is powered off.
v The hard-disk drive is powered off.
v The CPU stops.
To enter standby mode, press Fn+F4.
Note: You can change the action of Fn+F4, if you are
using the ACPI operating system.
In certain circumstances, the computer goes into standby
mode automatically:
v If a “suspend time” has been set on the timer, and the
user does not do any operation with the keyboard, the
TrackPoint, the hard disk, the parallel connector, or the
diskette drive within that time.
General descriptions
33
Related service information
v If the battery indicator blinks orange, indicating that the
battery power is low. (Alternatively, if Hibernate when
battery becomes low has been selected in the “Power
Management Properties” window, the computer goes
into hibernation mode.)
Note for the APM operating system:
Even if you do not set the low-battery alarm, the charge
indicator notifies you when the battery is low, and then the
computer enters the power-saving mode automatically.
This default low-battery behavior is independent of the
operating system; so if you have set the low-battery alarm,
the computer may not do what you specified. It chooses
either your setting or the default setting, whichever is
appropriate.
If you are using the ACPI operating system, only the
low-battery alarm is available.
To cause the computer to return from standby mode and
resume operation, do one of the following:
v Press the Fn key.
v Open the LCD cover.
v Turn on the power switch.
Also, the computer automatically returns from standby
mode and resumes operation in either of the following
events:
v The ring indicator (RI) is signaled by a serial device or a
PC Card device (Windows 2000 does not support the
ring indicator (RI) resume by PC Card device.)
v The time set on the resume timer elapses. In Windows
98, the Scheduled Tasks setting takes priority over the
Resume on timer selection in the “Power Management
Properties” window.
Note: The computer does not accept any input
immediately after it enters standby mode. Wait a
few seconds before taking any action to reenter
operation mode.
Hibernation mode
Note for Windows NT
If you are using Windows NT in the default format,
NTFS, you cannot create a hibernation file. If you
want to use hibernation mode, you will need to
reinstall Windows NT with FAT format.
In hibernation mode, the following occurs:
v The system status, RAM, VRAM, and setup data are
stored on the hard disk.
34
ThinkPad R40
Related service information
v The system is powered off.
Note: If the computer enters the hibernation mode while it
is docked to the docking station, do not undock it
from the docking station before resuming normal
operation. If you do undock it and then try to
resume normal operation, you will get an error
message, and you will have to restart the system.
To cause the computer to enter hibernation mode, do any
of the following:
v Press the Fn+F12 keys.
v If you are using the APM operating system and have set
the mode to Power switch mode [Hibernation], turn
off the power switch.
v If you are using the ACPI operating system and have
defined one of the following actions as the event that
causes the system to go into hibernation mode, perform
that action.
– Closing the lid.
– Pressing the power button.
– Pressing Fn+F4 keys.
Also, the computer goes into hibernation mode
automatically in either of the following conditions:
v If a “hibernation time” has been set on the timer, and the
user does not do any operation with the keyboard, the
TrackPoint, the hard-disk drive, the parallel connector, or
the diskette drive within that time.
v If the timer conditions are satisfied in suspend mode.
v If you are using the APM operating system and have set
the mode to Hibernate when battery becomes low,
and the battery charge becomes critically low.
When the power is turned on, the computer returns from
hibernation mode and resumes operation. The hibernation
file in the boot record on the hard-disk drive is read, and
system status is restored from the hard-disk drive.
General descriptions
35
Checkout guide
Checkout guide
Use the following procedures as a guide in identifying and
correcting problems with the ThinkPad computer.
Note: The diagnostic tests are intended to test only IBM
products. The use of non-IBM products, prototype
cards, or modified options can lead to false
indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as
possible.
2. Verify the symptoms. Try to re-create the failure by
running the diagnostic test or by repeating the
operation.
Testing the computer
The ThinkPad computer has a test program called
PC-Doctor® DOS (hereafter called PC-Doctor.) You can
detect errors by running the diagnostics test included in
PC-Doctor. This section is an overview of the procedure.
For details that depend on model-unique functions, refer to
“Product overview” on page 45.
For some possible configurations of the computer,
PC-Doctor might not run correctly. To avoid this problem,
you need to initialize the computer setup by use of the IBM
BIOS Setup Utility before you run PC-Doctor. On the IBM
BIOS Setup Utility screen, press F9, Enter, F10, and then
Enter.
Note: When you initialize the computer configuration,
some devices are disabled, such as the serial port.
If you test one of these devices, you will need to
enable it by using PS2.EXE.
PC-Doctor cannot be used to test a device that is in the
docking station, even if the computer supports the docking
station. To test a USB device, connect it to the USB
connector of the computer. To test the Ultrabay device,
install it in the Ultrabay Plus slot of the computer.
To run the test, do as follows:
Note: In the following procedure, you can select an item
not only with the arrow keys, but also with the
TrackPoint. Instead of pressing Enter, click the left
button.
1. Insert the PC-Doctor disk into the diskette drive; then
power on the computer.
If the computer cannot be powered on, go to “Power
system checkout” on page 39, and check the power
sources.
36
ThinkPad R40
Checkout guide
If an error code appears, go to “Symptom-to-FRU
index” on page 53.
On the first screen, select the model and press Enter.
Follow the instructions on the screen.
2. The main panel of PC-Doctor appears.
3. Select Diagnostics with the arrow keys, and press
Enter.
A pull-down menu appears. (Its exact form depends on
the model.)
The options on the test menu are as follows:
Diagnostics
Interactive Tests
v Run Normal Test
v Keyboard
v Run Quick Test
v Video
v CPU/Coprocessor
v Internal Speaker
v Systemboard
v Mouse
v Video Adapter
v Joystick Test
v Serial Ports
v Diskette
v Parallel Ports
v System Load
v Fixed Disks
v CD-ROM/DVD Test
v Diskette Drives
v Actiontec Wireless Radio
v Other Devices
v 802.11b Wireless Radio Test
v ZIP Drive
v LS-120/240 Drive
v Wireless LAN
v Memory Test – Full
v Memory Test – Quick
Notes:
v In the Keyboard test in Interactive Tests, the Fn key is
scanned only once. Each key should be held down for at least
2 seconds; otherwise, it cannot be sensed.
v Video Adapter test supports only the LCD display on
theThinkPad computer. Before running PC-Doctor DOS, detach
the external monitor.
v To test ZIP Drive or LS-120/240 Drive, each media is needed
to be inserted before start testing.
v To test Digital Signature Chip, the chip must be enabled.
v When Legacy Floppy Drives is enabled in the IBM BIOS Setup
Utility, Diskette Drives test is activated even if no legacy
diskette drive is attached to the ThinkPad computer.
General descriptions
37
Checkout guide
Diagnostics
I n t e r a c t i v e Te s t s
Hardware Info
Utility
Quit
F1=Help
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Serial Ports
Parallel Ports
Fixed Disks
Diskette Drives
Other Devices
ZIP Drive
LS-120/240 Drive
Communication
Wireless LAN
Memory Test - Full
Memory Test - Quick
PC-DOCTOR 2.0 Copyright 2001 PC-Doctor, Inc. All Rights Reserved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
4. Run the applicable function test.
5. Follow the instructions on the screen. If there is a
problem, PC-Doctor shows messages describing it.
6. To exit the test, select Quit — Exit Diag.
To cancel the test, press Esc.
Note: After executing PC-Doctor, check the system
time/date and reset them if needed.
Detecting system information with
PC-Doctor
PC-Doctor can detect the following system information:
Hardware Info
v
v
v
v
v
v
v
v
v
v
System Configuration
Memory Contents
Physical Disk Drives
Logical Disk Drives
VGA Information
IDE Drive Info
PCI Information
PNPISA Info
SMBIOS Info
VESA LCD Info
Utility
v
v
v
v
v
v
v
v
v
v
v
Run External Tests
Surface Scan Hard Disk
Benchmark System
DOS Shell
Tech Support Form
Battery Rundown
View Test Log
Print Log
Save Log
Full Erase Hard Drive
Quick Erase Hard Drive
38
ThinkPad R40
Checkout guide
Power system checkout
To verify a symptom, do the following:
1. Power off the computer.
2. Remove the battery pack.
3. Connect the ac adapter.
4. Check that power is supplied when you power on the
computer.
5. Power off the computer.
6. Disconnect the ac adapter and install the charged
battery pack.
7. Check that the battery pack supplies power when you
power on the computer.
If you suspect a power problem, see the appropriate one
of the following power supply checkouts:
v “Checking the ac adapter”
v “Checking operational charging” on page 40
v “Checking the battery pack” on page 40
v “Checking the backup battery” on page 42
Checking the ac adapter
You are here because the computer fails only when the ac
adapter is used:
v If the power problem occurs only when the port
replicator is used, replace the port replicator.
v If the power-on indicator does not turn on, check the
power cord of the ac adapter for correct continuity and
installation.
v If the computer does not charge during operation, go to
″Checking operational charging.″
To check the ac adapter, do the following:
1. Unplug the ac adapter cable from the computer.
2. Measure the output voltage at the plug of the ac
adapter cable. See the following figure:
2
1
Pin
Voltage (V dc)
1
+15.5 to +17.0
2
Ground
(16 - 10 V)
3. If the voltage is not correct, replace the ac adapter.
4. If the voltage is acceptable, do the following:
v Replace the system board.
General descriptions
39
Checkout guide
v If the problem persists, go to “Product overview” on
page 45.
Note: Noise from the ac adapter does not always indicate
a defect.
Checking operational charging
To check whether the battery charges properly during
operation, use a discharged battery pack or a battery pack
that has less than 50% of the total power remaining when
installed in the computer.
Perform operational charging. If the battery status indicator
or icon does not turn on, remove the battery pack and let it
return to room temperature. Reinstall the battery pack. If
the charge indicator or icon still does not turn on, replace
the battery pack.
If the charge indicator still does not turn on, replace the
system board. Then reinstall the battery pack. If it is still
not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter
shows that less than 95% of the total power remains;
under this condition the battery pack can charge to 100%
of its capacity. This protects the battery pack from being
overcharged or from having a shortened life.
To check the status of your battery, move your cursor to
the Power Meter icon in the icon tray of the Windows
taskbar and wait for a moment (but do not click), and the
percentage of battery power remaining is displayed. To get
detailed information about the battery, double-click the
Power Meter icon.
Note: If the battery pack becomes hot, it may not be able
to charge. Remove it from the computer and leave it
at room temperature for a while. After it cools down,
reinstall and recharge it.
For machine type 2681, 2682, 2683, 2722, 2723, 2724
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage
between battery terminals 1 (+) and 5 (−). See the
following figure:
40
ThinkPad R40
Checkout guide
5(-)
4 3
2
1(+)
Terminal
Voltage (V dc)
1
+ 0 to + 16.8
5
Ground (−)
3. If the voltage is less than +14.4 V dc, the battery pack
has been discharged.
Note: Recharging will take at least 3 hours, even if the
indicator does not turn on.
If the voltage is still less than +14.4 V dc after
recharging, replace the battery.
4. If the voltage is more than +14.4 V dc, measure the
resistance between battery terminals 4 and 5. The
resistance must be 4 to 30 K .
If the resistance is not correct, replace the battery
pack. If the resistance is correct, replace the system
board.
For machine type 2684, 2685
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage
between battery terminals 1 (+) and 5 (−). See the
following figure:
5(-)
4 3
2
1(+)
Terminal
Voltage (V dc)
1
+ 0 to + 12.6
5
Ground (−)
3. If the voltage is less than +11.0 V dc, the battery pack
has been discharged.
Note: Recharging will take at least 3 hours, even if the
indicator does not turn on.
If the voltage is still less than +11.0 V dc after
recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the
resistance between battery terminals 4 and 5. The
resistance must be 4 to 30 K .
General descriptions
41
Checkout guide
If the resistance is not correct, replace the battery
pack. If the resistance is correct, replace the system
board.
Checking the backup battery
Do the following:
1. Power off the computer, and unplug the ac adapter
from it.
2. Turn the computer upside down.
3. Remove the battery pack (see “1010 Battery pack” on
page 64).
4. Remove the backup battery (see “Checking the battery
pack” on page 40).
5. Measure the voltage of the backup battery. See the
following figure.
Red(+)
Blue(-)
Wire
Voltage (V dc)
Red
+2.5 to +3.2
Blue
Ground
v If the voltage is correct, replace the system board.
v If the voltage is not correct, replace the backup battery.
v If the backup battery discharges quickly after
replacement, replace the system board.
42
ThinkPad R40
ThinkPad R40
Product overview . . . . . . . . . . . . 45
Specifications . . . . . . . . . . . . 45
Status indicators . . . . . . . . . . . 48
FRU tests . . . . . . . . . . . . . 50
Fn key combinations . . . . . . . . . . 52
Symptom-to-FRU index . . . . . . . . . . 53
Numeric error codes . . . . . . . . . . 53
Error messages . . . . . . . . . . . 56
Beep symptoms . . . . . . . . . . . 57
No-beep symptoms . . . . . . . . . . 57
LCD-related symptoms . . . . . . . . . 58
Intermittent problems . . . . . . . . . . 59
Undetermined problems . . . . . . . . . 59
FRU replacement notices . . . . . . . . . 60
Screw notices . . . . . . . . . . . . 60
Retaining serial numbers. . . . . . . . . 61
Restoring the serial number of the system unit
61
Retaining the UUID . . . . . . . . . 61
Removing and replacing a FRU. . . . . . . . 63
1010 Battery pack. . . . . . . . . . . 64
1020 Ultrabay Plus device . . . . . . . . 65
1030 Hard-disk drive . . . . . . . . . . 66
1040 DIMM . . . . . . . . . . . . 68
1050 Mini PCI adapter . . . . . . . . . 70
1060 Keyboard . . . . . . . . . . . 73
1070 Backup battery . . . . . . . . . . 81
1080 Optical storage in the fixed bay . . . . . 82
1090 PC Card slot assembly . . . . . . . 85
1100 Hinge cover . . . . . . . . . . . 87
1110 Communication daughter card (CDC) . . . 88
Modem daughter card (MDC) . . . . . . 89
IBM Integrated Bluetooth with 56K Modem
(BMDC) . . . . . . . . . . . . 92
1120 Fan assembly . . . . . . . . . . 94
1130 CPU . . . . . . . . . . . . . 95
1140 Bluetooth antenna assembly . . . . . . 97
1150 LCD assembly . . . . . . . . . . 98
1160 Keyboard bezel . . . . . . . . . 103
1170 Speaker assembly and microphone cable
108
1180 System board . . . . . . . . . . 109
1190 Hard-disk drive slot . . . . . . . . 116
2000 Ultrabay Plus guide rail . . . . . . . 117
2010 I/O Bracket . . . . . . . . . . . 119
2020 LCD front bezel . . . . . . . . . 120
2030 Inverter card . . . . . . . . . . 121
2040 LCD panel and LCD cable assembly . . . 122
2050 Antenna assembly, hinges, and LCD cover
124
Locations . . . . . . . . . . . . . . 127
Front view for 2681, 2682, 2683, 2722, 2723, 2724 127
Rear view for 2681, 2682, 2683, 2722, 2723, 2724 129
© Copyright IBM Corp. 2004
43
Bottom view for 2681, 2682, 2683, 2722, 2723,
2724 . . . . . . . . . . . .
Front view for 2684, 2685 . . . . . . .
Rear view for 2684, 2685 . . . . . . .
Bottom view for 2684, 2685 . . . . . .
Parts list . . . . . . . . . . . . .
R40 series model matrix . . . . . . .
Overall . . . . . . . . . . . .
LCD FRUs . . . . . . . . . . .
13/14 in. TFT . . . . . . . . . .
15 in. TFT . . . . . . . . . .
Keyboard . . . . . . . . . . . .
Recovery CDs . . . . . . . . . .
For Windows 2000 Professional . . . .
For Windows XP Home Edition . . . .
For Windows XP professional . . . . .
Miscellaneous parts . . . . . . . . .
AC adapters . . . . . . . . . . .
Telephone cable . . . . . . . . . .
Optional FRUs . . . . . . . . . .
Ultrabay Plus devices . . . . . . .
Other optional FRUs . . . . . . .
Common parts list . . . . . . . . .
Tools . . . . . . . . . . . .
Power cords (system) . . . . . . .
Power cords (ThinkPad Mini Dock) . . .
Notices . . . . . . . . . . . . .
Trademarks . . . . . . . . . . .
44
ThinkPad R40
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
130
131
132
133
134
134
144
161
162
163
165
166
166
167
168
169
172
173
174
174
174
176
176
176
177
178
178
Product overview
Product overview
This section presents the following product-unique
information:
v “Specifications”
v “Status indicators” on page 48
v “FRU tests” on page 50
v “Fn key combinations” on page 52
Specifications
The following table lists the specifications of the ThinkPad
R40 series:
Feature
Description
Processor
2681, 2682, 2683
v Mobile Intel® Pentium® 4 processor- M 1.8/
1.9/ 2.0/ 2.2/2.4GHz, L2 512 KB cache
v Mobile Intel® Celeron® Processor 1.6/
1.8GHz, L2 256KB cache
2684, 2685
v Mobile Intel® Pentium® 4 processor- M
1.8GHz, L2 512 KB cache
v Mobile Intel® Celeron® Processor 1.7/
1.8GHz, L2 256KB cache
2722, 2723, 2724
v Intel® Pentium® M Processor 1.3/ 1.4/
1.5GHz, L2 1MB cache
Bus
architecture
v
v
v
v
v
Memory
(standard)
v 128 MB DDR SDRAM SO DIMM (PC2100)
card × 1
v 256 MB DDR SDRAM SO DIMM (PC2100)
card × 1
v 512 MB DDR SDRAM SO DIMM (PC2100)
card × 1
Memory
(optional)
v 128 MB DDR SDRAM SO DIMM (PC2100)
card
v 256 MB DDR SDRAM SO DIMM (PC2100)
card
v 512 MB DDR SDRAM SO DIMM (PC2100)
v 1 GB DDR SDRAM SO DIMM (PC2100) —
on some models
Graphic
memory
2681, 2682, 2683, 2722, 2723, 2724
v 16 MB DDR SDRAM (on the system board)
v 32 MB DDR SDRAM (on the system board)
400MHz PSB
HUB link (on some models)
PCI bus
LPC bus
266MHz DDR SDRAM (PC2100)
2684, 2685
v 16 MB DDR SDRAM (on the system board)
ThinkPad R40
45
Product overview
Feature
Description
CMOS RAM
v 242 bytes
Hard-disk drive
2681, 2682, 2683, 2722, 2723, 2724
v 20.0 GB, 4200 rpm, 2.5-inch, IDE interface
v 30.0 GB, 4200 rpm, 2.5-inch, IDE interface
v 40.0 GB, 4200 rpm, 2.5-inch, IDE interface
v 40.0 GB, 5400 rpm, 2.5-inch, IDE interface
v 60.0 GB, 4200 rpm, 2.5-inch, IDE interface
2684, 2685
v 20.0 GB, 4200 rpm, 2.5-inch, IDE interface
v 30.0 GB, 4200 rpm, 2.5-inch, IDE interface
v 40.0 GB, 4200 rpm, 2.5-inch, IDE interface
Display
2681, 2682, 2683, 2722, 2723, 2724
v 13.3-inch, 16M colors, XGA (1024 × 768
resolution) TFT color LCD
v 14.1-inch, 16M colors, XGA (1024 × 768
resolution) TFT color LCD
v 15-inch, 16M colors, XGA (1024 × 768
resolution) TFT color LCD
v 15-inch, 16M colors, SXGA+ (1400 × 1050
resolution) TFT color LCD
2684, 2685
v 13.3-inch, 16M colors, XGA (1024 × 768
resolution) TFT color LCD
v 14.1-inch, 16M colors, XGA (1024 × 768
resolution) TFT color LCD
I/O port
2681, 2682, 2683, 2722, 2723, 2724
v External monitor connector
v Stereo headphone jack
v Infrared port
v IEEE 1394 port
v Microphone jack
v Parallel connector
v Docking connector
v RJ11 connector
v RJ45 connector
v S-Video out connector
v Universal serial bus (USB) connector × 2
2684, 2685
v External monitor connector
v Stereo headphone jack
v Microphone jack
v Parallel connector
v RJ11 connector
v RJ45 connector
v Universal serial bus (USB) connector × 2
v Internal mono speaker (on some models)
v Internal stereo speakers (on some models)
v Software control volume
Audio
Infrared transfer v IrDA 1.1
Mini PCI
adapter
46
v IEEE 802.11b wireless LAN card
v IEEE 802.11a/b wireless LAN Combo card
ThinkPad R40
Product overview
Feature
Description
PC Card
v Type-II or Type-III
Communication
daughter card
(CDC)
v V.90 modem daughter card (MDC)
v Bluetooth Modem daughter card (BMDC)
AC adapter
v 72-watt type
Ultrabay Plus
device
(standard)
v CD-ROM drive
v DVD drive
v CD-RW/DVD combo drive
Preinstalled
operating
system
2681, 2682, 2683, 2722, 2723, 2724
Windows 2000 Professional
Windows XP Home Edition
Windows XP Professional
2684, 2685
Windows XP Home Edition
Windows XP Professional
ThinkPad R40
47
Product overview
Status indicators
The system status indicators show the status of the
computer, as follows:
1 2
3 4 5 6 7 8
TM
9
Indicator
Meaning
1 Bluetooth
status
Green:
Bluetooth is operational. This
indicator is on when the Bluetooth is
on and not in suspend mode.
2 Wireless
status
Green:
Wireless is operational. This indicator
is on when the Wireless is on and
not in suspend mode.
(continued)
48
ThinkPad R40
Product overview
Indicator
Meaning
3 Drive in
use
Green:
Data is being read from or written to
the hard-disk drive, the diskette drive,
or the drive in the Ultrabay Plus
device. When this indicator is on, do
not put the computer into standby
mode or turn off the computer.
Note: Do not move the system while the green
drive-in-use light is on. Sudden physical shock
could cause drive errors.
4 Num lock
Green:
The numeric keypad on the keyboard
is enabled. To enable or disable the
keypad, press and hold the Shift key,
and press the NumLk (ScrLk) key.
5 Caps lock
Green:
Caps Lock mode is enabled. To
enable or disable Caps Lock mode,
press the Caps Lock key.
6 Power on
Green:
The computer is on and ready to use.
This indicator stays lit whenever the
computer is on and is not in standby
mode.
7 Battery
status
Green:
8 Standby
status
Green:
The computer is in standby mode.
Blinking green:
The computer is entering standby
mode or hibernation mode, or is
resuming normal operation.
9 Ultrabay
status
Green:
The battery is in use and has enough
power. The ac adapter has charged
the battery completely.
Blinking green:
The battery is being charged, but still
has enough power to operate. (At
regular intervals, the indicator light
turns off briefly.)
Orange: The battery is being charged, but the
battery power is still low.
Blinking orange:
The battery needs to be charged.
When the indicator starts blinking
orange, the computer beeps three
times.
An Ultrabay Plus device is installed
and in use.
Blinking green:
An Ultrabay Plus device is in the
process of being detached.
Turn off: An Ultrabay Plus device is ready to
be attached or detached.
Note: If you are using Windows 2000, the
Ultrabay status indicator does not blink while an
Ultrabay Plus device is being detached. Instead,
a message box pops up when the process is
completed; then the indicator turns off.
ThinkPad R40
49
Product overview
FRU tests
The following table shows the test for each FRU.
FRU
Applicable test
System board
1. Diagnostics --> CPU/Coprocessor
2. Diagnostics --> Systemboard
Power
Diagnostics --> Other Devices --> IBM AC
Adapter, IBM Battery 1 (IBM Battery 2)
LCD unit
1. Diagnostics --> Video Adapter
2. Interactive Tests --> Video
Modem,
Modem
daughter card
1. Make sure the modem is set up correctly.
2. Replace the modem jack and the modem
card in turn, and run the following tests in
Diagnostics --> Other Devices:
a. Modem Digital Loopback Test
b. Modem Dialtone Test
Audio
1. Interactive Tests --> Internal Speaker
2. Diagnostics --> Other Devices --> Analog
Devices AC97 CODEC Test
Speaker
Interactive Tests --> Internal Speaker
PC Card slots
Diagnostics --> Systemboard --> PCMCIA,
PCMCIA External Loop
Keyboard
1. Diagnostics --> Systemboard -->
Keyboard
2. Interactive Tests --> Keyboard
TrackPoint or
pointing device
If the TrackPoint does not work, check the
configuration in the ThinkPad Configuration
program. If the TrackPoint is disabled, select
Automatic (or Enabled) to enable it.
After you use the TrackPoint, the pointer may
drift on the screen for a short time. This drift
can occur when a slight, steady pressure is
applied to the TrackPoint pointer. This symptom
is not a hardware problem. If the pointer stops
after a short time, no service action is
necessary.
If enabling the TrackPoint does not correct the
problem, continue with the following:
v Interactive Tests --> Mouse
Hard-disk drive
Diagnostics --> Fixed Disks
Diskette drive
1. Diagnostics --> Diskette Drives
2. Interactive Tests --> Diskette
(continued)
50
ThinkPad R40
Product overview
FRU
Applicable test
CD-ROM or
DVD drive
1. Diagnostics --> Other Devices -->
CD-ROM/DVD
2. Interactive Tests --> CD-ROM/DVD Test
Memory
1. If two DIMMs are installed, remove one of
them and run Diagnostics --> Memory
Test—Quick.
2. If the problem does not recur, return the
DIMM to its place, remove the other one,
and run the test again.
3. If the test does not detect the error, run
Diagnostics --> Memory Test—Full.
Fan
1. Turn on the computer and check the air
turbulence at the louver near the power
switch.
2. Run Diagnostics --> Other Devices -->
IBM Fan.
Touch pad
If the Touch Pad does not work, check the
configuration in the ThinkPad Configuration
program. If the Touch Pad is disabled, select
Automatic to enable it. If enabling the Touch
Pad does not correct the problem, continue with
the following:
v Interactive Tests --> Mouse
ThinkPad R40
51
Product overview
Fn key combinations
The following table shows the function of each combination
of Fn with a function key.
Key
combination
Description
Fn+F1
Reserved.
Fn+F2
Reserved.
Fn+F3
Turn off the LCD display, leaving the screen
blank. To turn the LCD display on again, press
any key or the TrackPoint stick.
Fn+F4
Put the computer in standby mode. To return to
normal operation, press the Fn key
independently, without pressing a function key.
Note: In Windows XP and Windows 2000, this
combination of buttons functions as a sleep
button. The setting can be changed so that
pressing it puts the computer into hibernation
mode or even shuts the computer down.
Fn+F5
Turn the Bluetooth on or off.
Fn+F6
Reserved.
Fn+F7
Apply a presentation scheme directly, with no
need to start Presentation Director.
Fn+F8
Switch the computer screen size between
expanded and normal mode if the computer
display image is smaller than the physical
display.
Note: This function is not supported in
Windows 2000 and Windows XP.
Fn+F9
Turn the Easy Eject on or off.
Fn+F10
Reserved.
Fn+F11
Reserved.
Fn+F12
Put the computer into hibernation mode. To
return to normal operation, press the power
button for less than four seconds.
Note: In Windows 2000 and Windows XP, you
can use Fn+F12 for hibernation only if the IBM
PM device driver has been installed on the
computer.
Fn+PgUp
Turn the ThinkLight on or off.
Fn+Home
The computer display becomes brighter.
Fn+End
The computer display becomes less bright.
Fn+Spacebar
Enable the FullScreen Magnifier function.
52
ThinkPad R40
Symptom-to-FRU index
Symptom-to-FRU index
The symptom-to-FRU index in this section lists symptoms
and errors and their possible causes. The most likely
cause is listed first, in boldface type.
Note: Do the FRU replacement or other actions in the
sequence shown in the column headed “FRU or
action, in sequence.” If replacing a FRU does not
solve the problem, put the original part back in the
computer. Do not replace a nondefective FRU.
This index can also help you determine, during regular
servicing, what FRUs are likely to need to be replaced
next.
A numeric error is displayed for each error detected in
POST or system operation. In the displays, n can be any
number.
If no numeric code is displayed, check the narrative
descriptions of symptoms. If the symptom is not described
there, go to “Intermittent problems” on page 59.
Note
For an IBM device not supported by diagnostic
codes in the ThinkPad notebook computers, see the
manual for that device.
Numeric error codes
Symptom or error
FRU or action, in sequence
0175
Bad CRC1, stop POST
task—The EEPROM checksum
is not correct.
System board.
0176
System Security—The System
has been tampered with.
1. Run IBM BIOS Setup
Utility and Load Setup
Defaults.
2. System board.
0177
System board.
Bad SVP data, stop POST task.
0182
Bad CRC2. Enter BIOS Setup
and load Setup Defaults.
Run IBM BIOS Setup Utility
and Load Setup Defaults.
0185
Bad startup sequence settings.
Enter BIOS Setup and load
setup defaults.
Run IBM BIOS Setup Utility
and Load Setup Defaults
ThinkPad R40
53
Symptom-to-FRU index
Symptom or error
FRU or action, in sequence
0187
EAIA data access error—The
access to EEPROM is failed.
System board.
0188
Invalid RFID serialization
information area or bad
CRC2—The EEPROM
checksum is not correct.
System board.
0189
Invalid RFID configuration
information area—The
EEPROM checksum is not
correct.
System board.
0190
Critical low-battery error
1. Charge the battery pack.
2. Battery pack.
0199
1. Confirm supervisor
System security — IBM security
password and try again.
password retry count exceeded. 2. Run IBM BIOS Setup
Utility.
01C8
More than one modem devices
are found. Remove one of
them. Press <Esc> to continue.
1. Remove either a Mini PCI
modem card or an modem
daughter card; or press
Esc to ignore the warning
message.
2. System board.
0200
Hard disk error—The hard disk
is not working.
1. Reset the hard-disk drive.
2. Load Setup Defaults in IBM
BIOS Setup Utility.
3. Hard-disk drive.
4. System board.
021x
Keyboard error
Run interactive tests of the
keyboard and the auxiliary
input device.
0220
Monitor type error—Monitor
type does not match the one
specified in CMOS.
Load Setup Defaults in IBM
BIOS Setup Utility.
0230
Shadow RAM error—Shadow
RAM fails at offset nnnn.
System board.
0231
System RAM error—System
RAM fails at offset nnnn.
1. DIMM.
2. System board.
0232
Extended RAM
error—Extended RAM fails at
offset nnnn.
1. DIMM.
2. System board.
54
ThinkPad R40
Symptom-to-FRU index
Symptom or error
FRU or action, in sequence
0250
System battery error—System
battery is dead.
Replace the backup battery
and run IBM BIOS Setup
Utility to reset the time and
date.
0251
System CMOS checksum
bad—Default configuration
used.
Replace the backup battery
and run IBM BIOS Setup
Utility to reset the time and
date.
0252
Password checksum bad—The
password is cleared.
Reset the password by
running IBM BIOS Setup
Utility.
0260
System timer error
1. Replace the backup
battery and run IBM BIOS
Setup Utility to reset the
time and date.
2. System board.
0270
Real time clock error
1. Replace the backup
battery and run IBM BIOS
Setup Utility to reset the
time and date.
2. System board.
0271
Date and time error—Neither
the date nor the time is set in
the computer.
Run IBM BIOS Setup Utility to
reset the time and date.
0280
Previous boot
incomplete—Default
configuration used.
1. Load “Setup Default” in
IBM BIOS Setup Utility.
2. DIMM.
3. System board.
02B2
Incorrect drive A type
1. Diskette drive.
2. External FDD cable.
3. I/O card.
02F4
EISA CMOS not writable
1. Load Setup Defaults in
IBM BIOS Setup Utility.
2. Replace the backup battery.
3. System board.
02F5
DMA test failed
1. DIMM.
2. System board.
02F6
Software NMI failed
1. DIMM.
2. System board.
02F7
Fail-safe timer NMI failed
1. DIMM.
2. System board.
1801
Attached docking station is not
supported
Shut down the computer and
remove it from the docking
station.
1802
Unauthorized network card is
plugged in—Power off and
remove the miniPCI network
card.
1. Remove Mini PCI network
card.
2. System board.
ThinkPad R40
55
Symptom-to-FRU index
Error messages
Symptom or error
FRU or action, in sequence
Device address conflict.
1. Load “Setup Defaults” in
IBM BIOS Setup Utility.
2. Backup battery.
3. System board.
Allocation error for device.
1. Load “Setup Defaults” in
IBM BIOS Setup Utility.
2. Backup battery.
3. System board.
Failing bits: nnnn.
1. DIMM.
2. System board.
Invalid system configuration
data.
1. DIMM.
2. System board.
I/O device IRQ conflict.
1. Load “Setup Defaults” in
IBM BIOS Setup Utility.
2. Backup battery.
3. System board.
Operating system not found.
1. Check that the operating
system has no failure and is
installed correctly.
2. Enter IBM BIOS Setup
Utility and see whether
the hard-disk drive and
the diskette drive are
properly identified.
3. Reset the hard-disk drive.
4. Reinstall the operating
system.
5. Diskette drive.
6. Hard-disk drive.
7. System board.
Hibernation error.
1. Restore the system
configuration to what it
was before the computer
entered hibernation mode.
2. If memory size has been
changed, re-create the
hibernation file.
Fan error.
Fan.
Thermal sensing error.
System board.
56
ThinkPad R40
Symptom-to-FRU index
Beep symptoms
Symptom or error
FRU or action, in sequence
One beep and a blank,
unreadable, or flashing LCD.
1.
2.
3.
4.
One long and two short beeps,
and a blank or unreadable
LCD.
1. System board.
2. LCD assembly.
3. DIMM.
Two short beeps with error
codes.
POST error. See “Numeric
error codes” on page 53.
Two short beeps and a blank
screen.
1. System board.
2. DIMM.
Three short beeps, pause,
three more short beeps, and
one short beep.
1. DIMM.
2. System board
Reset the LCD connector.
LCD assembly.
External CRT.
System board.
One short beep, pause, three
short beeps, pause, three more
short beeps, and one short
beep.
Only cursor appears.
Reinstall operating system.
Four cycles of four short beeps
and a blank screen.
System board (IBM security
chip)
Five short beeps and a blank
screen.
System board
No-beep symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator
on, LCD blank, and no POST.
1. Make sure that every
connector is connected
tightly and correctly.
2. DIMM.
3. System board.
No beep, power-on indicator
on, and LCD blank during
POST.
1. Reset DIMM.
2. System board.
The power-on password prompt
appears.
A power-on password or a
supervisor password is set.
Type the password and press
Enter.
The hard-disk password prompt
appears.
A hard-disk password is set.
Type the password and press
Enter.
The DOS full screen looks
smaller.
Start the ThinkPad
Configuration program and set
the Screen expansion
function.
ThinkPad R40
57
Symptom-to-FRU index
LCD-related symptoms
Important
The TFT LCD for the notebook computer contains
many thin-film transistors (TFTs). A small number of
dots that are missing, discolored, or always lighted
is characteristic of TFT LCD technology, but
excessive pixel problems can cause viewing
concerns. The LCD should be replaced if the
number of missing, discolored, or lighted dots in any
background is:
v XGA: 8 or more bright dots, 8 or more dark dots,
or a total of 9 or more bright and dark dots.
v SXGA+: 11 or more bright dots, 13 or more dark
dots, or a total of 16 or more bright and dark
dots.
Note: A bright dot means a pixel is always on
(white or color.) A dark dot means a pixel is
always off (black color.)
Symptom or error
FRU or action, in sequence
No beep, power-on indicator
on, and a blank LCD during
POST.
System board.
v LCD backlight not working.
v LCD too dark.
v LCD brightness cannot be
adjusted.
v LCD contrast cannot be
adjusted.
1. Reset the LCD
connectors.
2. LCD assembly.
3. System board.
v
v
v
v
1. See important note for
“LCD-related symptoms.”
2. Reset all LCD connectors.
3. LCD assembly.
4. System board.
LCD screen unreadable.
Characters missing pixels.
Screen abnormal.
Wrong color displayed.
Horizontal or vertical lines
displayed on LCD.
58
ThinkPad R40
LCD assembly.
Symptom-to-FRU index
Intermittent problems
Intermittent system hang problems can be due to a variety
of causes that have nothing to do with a hardware defect,
such as cosmic radiation, electrostatic discharge, or
software errors. FRU replacement should be considered
only when a problem recurs.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop
mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the
FRU code. Rerun the test to verify that no more errors
exist.
Undetermined problems
You are here because the diagnostic tests did not identify
which adapter or device failed, wrong devices are installed,
a short circuit is suspected, or the system is inoperative.
Follow these procedures to isolate the failing FRU (do not
isolate FRUs that have no defects).
Verify that all attached devices are supported by the
computer.
Verify that the power supply being used at the time of the
failure is operating correctly. (See “Power system
checkout” on page 39.)
1. Power off the computer.
2. Visually check each FRU for damage. Replace any
damaged FRU.
3. Remove or disconnect all of the following devices:
a. Non-IBM devices
b. Devices attached to the port replicator
c. Printer, mouse, and other external devices
d. Battery pack
e. Hard-disk drive
f. External diskette drive
g. DIMM
h. CD-ROM and diskette drive in the Ultrabay
i. PC Cards
4. Power on the computer.
5. Determine whether the problem has changed.
6. If the problem does not recur, reconnect the removed
devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one
at a time (do not replace a nondefective FRU):
a. System board
b. LCD assembly
ThinkPad R40
59
FRU replacement notices
FRU replacement notices
This section contains notices related to removing and
replacing parts. Read this section carefully before replacing
any FRU.
Screw notices
Loose screws can cause a reliability problem. In IBM
ThinkPad computer, this problem is addressed with special
nylon-coated screws that have the following characteristics:
v They maintain tight connections.
v They do not easily come loose, even with shock or
vibration.
v They are harder to tighten.
v They should be used only once.
Do the following when you service this machine:
v Keep the screw kit (for the P/N, see “Miscellaneous
parts” on page 169) in your tool bag.
v Always use new screws.
v Use a torque screwdriver if you have one.
Tighten screws as follows:
v Plastic to plastic
Turn an additional 90 degrees after the screw head
touches the surface of the plastic part:
90 degrees more
(Cross-section)
v Logic card to plastic
Turn an additional 180 degrees after the screw head
touches the surface of the logic card:
180 degrees more
(Cross-section)
v Torque driver
If you have a torque driver, refer to the “Torque” column
for each step.
60
ThinkPad R40
FRU replacement notices
v Make sure you use the correct screw. If you have a
torque screwdriver, tighten all screws firmly to the torque
shown in the table. Never use a screw that you
removed. Use a new one. Make sure the screws are
tightened firmly.
Retaining serial numbers
This section includes the following descriptions:
v “Restoring the serial number of the system unit”
v “Retaining the UUID”
Restoring the serial number of the system
unit
When the computer was manufactured, the EEPROM on
the system board was loaded with the serial numbers of
the system and all major components. These numbers
need to remain the same throughout the life of the
computer.
If you replace the system board, you must restore the
serial number of the system unit to its original value.
Before replacing the system board, save the original serial
number by doing the following:
1. Install the ThinkPad hardware maintenance diskette
version 1.69, and restart the computer.
2. From the main menu, select 1. Set System
Identification.
3. Select 2. Read S/N data from EEPROM.
The serial number for each device is displayed. Write
down the serial number of the system unit, designated as
follows:
20: System unit serial number
After you have replaced the system board, restore the
serial number by doing the following:
1. Install the ThinkPad hardware maintenance diskette
version 1.69, and restart the computer.
2. From the main menu, select 1. Set System
Identification.
3. Select 1. Add S/N data from EEPROM.
Follow the instructions on the screen.
Note: The serial number of the system unit is written on
the label attached on the bottom of the computer.
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit
number uniquely assigned to your computer at production
ThinkPad R40
61
FRU replacement notices
and stored in the EEPROM of your system board. The
algorithm that generates the number is designed to provide
unique IDs until the year A.D. 3400. No two computers in
the world have the same number.
When you replace the system board, you must set the
UUID on the new system board as follows:
1. Install the ThinkPad hardware maintenance diskette
version 1.69, and restart the computer.
2. From the main menu, select 4. Assign UUID.
A new UUID is created and written. If a valid UUID
already exists, it is not overwritten.
62
ThinkPad R40
Removing and replacing a FRU
Removing and replacing a FRU
This section presents directions and drawings for use in
removing and replacing a FRU. Be sure to observe the
following general rules:
1. Do not try to service any computer unless you have
been trained and certified. An untrained person runs
the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement
notices” on page 60.
3. Begin by removing any FRUs that have to be removed
before the failing FRU. Any such FRUs are listed at the
top of the page. Remove them in the order in which
they are listed.
4. Follow the correct sequence in the steps for removing
the FRU, as indicated in the drawings by the numbers
in square callouts.
5. When turning a screw to replace a FRU, turn it in the
direction indicated by the arrow in the drawing.
6. When removing the FRU, move it in the direction
indicated by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal
procedure and follow any notes that pertain to
replacement. For information about connecting and
arranging internal cables, see “Locations” on page 127.
8. When replacing a FRU, use the correct screw as
shown in the procedures.
DANGER
Before removing any FRU, power off the computer, unplug all
power cords from electrical outlets, remove the battery pack,
and then disconnect any interconnecting cables.
Attention: Before the computer is powered on after FRU
replacement, make sure that all screws, springs, and other
small parts are in place and are not loose inside the
computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes
can cause electrical short circuits.
Attention: The system board is sensitive to, and can be
damaged by, electrostatic discharge. Before touching it,
establish personal grounding by touching a ground point
with one hand or by using an electrostatic discharge (ESD)
strap (P/N 6405959).
ThinkPad R40
63
Removing and replacing a FRU
1010 Battery pack
DANGER
The use only the battery in the parts listing for your
computer. Use of an incorrect battery can result in ignition or
explosion of the battery.
2
1
64
ThinkPad R40
Removing and replacing a FRU
1020 Ultrabay Plus device
For machine type 2681, 2682, 2683, 2722, 2723, 2724
Note
Any of Ultrabay Plus devices can be installed into
the Ultrabay Plus of the computer. The procedure
for installing and removing is the same for every
Ultrabay Plus device. For devices supported, see
“Optional FRUs” on page 174.
Note: When you release the switch in step 1, the lever
pops out. Pull the lever a little in step 2 to release
the device from the bay.
1
2
1
2
3
ThinkPad R40
65
Removing and replacing a FRU
1030 Hard-disk drive
Attention
v Do not drop or apply any shock to the
hard-disk drive. The hard-disk drive is sensitive
to physical shock. Improper handling can cause
damage and permanent loss of data.
v Before removing the drive, have the user make a
backup copy of all the information on the drive if
possible.
v Never remove the drive while the system is
operating or is in suspend mode.
For access, remove this FRU:
v “1010 Battery pack” on page 64
1
Note: The hard disk is attached to the cover.
Step
Screw (quantity)
1
HDD M3 × 3.5 mm, Black (1)
(continued)
66
ThinkPad R40
Removing and replacing a FRU
2
3
4
3
When installing: Make sure that the hard-disk connector
is firmly attached.
ThinkPad R40
67
Removing and replacing a FRU
1040 DIMM
For access, remove this FRU:
v “1010 Battery pack” on page 64
Note: Loosen the screws 1, but do not remove them.
2
1
Step
Screw (quantity)
Torque
1
M2.5 x 3.5 mm, +/- Head BK(2)
0.294 Nm
(3 kgfcm)
(continued)
68
ThinkPad R40
Removing and replacing a FRU
3
4
3
When installing: With the notched end of the DIMM
toward the socket, insert the DIMM into
the socket, and then press it firmly. Pivot
the DIMM until it snaps into place. Make
sure that the card is firmly fixed in the
slot and does not move easily.
ThinkPad R40
69
Removing and replacing a FRU
1050 Mini PCI adapter
For access, remove this FRU:
v “1010 Battery pack” on page 64
Note: Some models do not have the Mini PCI card socket.
Note: Loosen the screw 1a or 1b, but do not remove
it. In order to loosen 1b, use the driver FRU
9900712 and TR7bit FRU 00P6967 (See “Tools” on
page 176).
2
1a
1b
Step
Screw (quantity)
Torque
1a
M2.5 x 3.5 mm, +/- Head BK (1)
0.294 Nm
(3 kgfcm)
1b
M2.5 x 3.5 mm, Hexagon Head BK
(1), Tip: TR7, Torx — 802.11a/b Model
0.294 Nm
(3 kgfcm)
Note: The TR7 torx screw is required to be present when
the 802.11 a/b card is installed in order to meet
FCC requirements. Do not replace this with any
other screw type.
The following illustrations for step 3 to step 6 show the
combination of the Mini PCI Wireless LAN card.
3
(continued)
70
ThinkPad R40
Removing and replacing a FRU
Antenna cables 4a and 4b are for the wireless LAN
feature.
Note: When unplugging the antenna jack, do not pull the
cable; it might snap. Unplug the jack by pulling a
tab with your fingers.
4b
4a
When installing: Plug the gray antenna cable with the tab
marked “MAIN” (4a) into jack J1, and
the black antenna cable with the tab
marked “AUX” (4b) into jack J2.
(continued)
ThinkPad R40
71
Removing and replacing a FRU
5
6
5
When installing: With the notched end of the card toward
the socket, insert the card into the
socket, and then press it firmly. Pivot the
card until it snaps into place. Make sure
that the card is firmly fixed in the slot
and does not move easily.
72
ThinkPad R40
Removing and replacing a FRU
1060 Keyboard
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
For machine type 2681, 2682, 2683, 2722, 2723, 2724
1
Step
Screw (quantity)
Torque
1
M2.5 × 8.5 mm, Black (2)
0.294 Nm
(3 kgfcm)
(continued)
ThinkPad R40
73
Removing and replacing a FRU
4
3
2
In step 5, pull the keyboard a little in the direction of the
arrow, and then detach the connector 6.
5
6
74
ThinkPad R40
Removing and replacing a FRU
When installing: Install the keyboard, following the
directions below.
1. Attach the connector. (Step 6 in the removal
procedure.)
2. Make sure that the keyboard edges, shown in the
figure as (A) and (B), are under the frame.
(A)
(B)
3. Press the keys indicated by arrows to latch the
keyboard firmly in place.
(continued)
ThinkPad R40
75
Removing and replacing a FRU
4. To make sure that the front side of the keyboard is
housed firmly, gently press the keys with your thumbs
and try to slide the keyboard towards you.
5. Secure the keyboard from the bottom of the computer,
using the new screws provided with the keyboard.
76
ThinkPad R40
Removing and replacing a FRU
For machine type 2684, 2685
1
Step
Screw (quantity)
Torque
1
M2.5 × 8.5 mm, Black (2)
0.294 Nm
(3 kgfcm)
(continued)
ThinkPad R40
77
Removing and replacing a FRU
4
3
2
In step 5, pull the keyboard a little in the direction of the
arrow, and then detach the connector 6.
5
6
78
ThinkPad R40
Removing and replacing a FRU
When installing: Install the keyboard, following the
directions below.
1. Attach the connector. (Step 6 in the removal
procedure.)
2. Make sure that the keyboard edges, shown in the
figure as (A) and (B), are under the frame.
(A)
(B)
3. Press the keys indicated by arrows to latch the
keyboard firmly in place.
(continued)
ThinkPad R40
79
Removing and replacing a FRU
4. To make sure that the front side of the keyboard is
housed firmly, gently press the keys with your thumbs
and try to slide the keyboard towards you.
5. Secure the keyboard from the bottom of the computer,
using the new screws provided with the keyboard.
80
ThinkPad R40
Removing and replacing a FRU
1070 Backup battery
DANGER
The use only the battery in the parts listing for your
computer. Use of an incorrect battery can result in ignition or
explosion of the battery.
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1060 Keyboard” on page 73
2
1
When installing: Make sure that the connector 1 is
firmly attached.
ThinkPad R40
81
Removing and replacing a FRU
1080 Optical storage in the fixed bay
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1060 Keyboard” on page 73
For machine type 2684, 2685
1
Step
Screw (quantity)
Torque
1
M2.5 x 6 mm, Yellow (1)
0.294 Nm
(3 kgfcm)
(continued)
82
ThinkPad R40
Removing and replacing a FRU
Pull the L-shaped bracket to the right of the computer and
drag out the built-in optical drive from the computer.
Note: There is a sharp object next to the bracket inside
the square opening. Be careful not to cut your
finger.
2
(continued)
ThinkPad R40
83
Removing and replacing a FRU
3
84
ThinkPad R40
Removing and replacing a FRU
1090 PC Card slot assembly
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1040 DIMM” on page 68
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
1
1
1
1
Step
Screw (quantity)
Torque
1
M2.0 × 4.5 mm, Yellow (4) Tip(0)
0.294 Nm
(3 kgfcm)
(continued)
ThinkPad R40
85
Removing and replacing a FRU
2
When installing: Make sure that the connector of the PC
card slot is firmly attached, and then
secure the screws.
86
ThinkPad R40
Removing and replacing a FRU
1100 Hinge cover
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
When installing: Attach the hinge cover, aligning the two
projections on the rear side with the two
small square holes of the base cover.
ThinkPad R40
87
Removing and replacing a FRU
1110 Communication daughter card
(CDC)
For access, remove this FRU:
v “1010 Battery pack” on page 64
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
Note: Some models do not have the Communication
daughter card (CDC).
Note: Loosen the screws 1 and 2.
1
2
Step
Screw (quantity)
Torque
1
M2.5 x 8.5 mm, BK (2)
0.294 Nm
(3 kgfcm)
2
M2.5 x 8.5 mm, BK (1)
0.294 Nm
(3 kgfcm)
88
ThinkPad R40
Removing and replacing a FRU
Modem daughter card (MDC)
5
4
3
(continued)
ThinkPad R40
89
Removing and replacing a FRU
6
7
When installing: Make sure that connector 6 is firmly
attached.
8
9
Step
Screw (quantity)
Torque
8
M2.5 x 6 mm, Yellow (1)
0.294 Nm
(3 kgfcm)
(continued)
90
ThinkPad R40
Removing and replacing a FRU
10
11
Step
Screw (quantity)
Torque
10
M2.0 x 3.5 mm, Silver (2)
0.294 Nm
(3 kgfcm)
12
13
Step
Screw (quantity)
Torque
12
M2.0 x 3.5 mm, Silver (1)
0.294 Nm
(3 kgfcm)
(continued)
ThinkPad R40
91
Removing and replacing a FRU
15
14
When installing: Make sure that connectors 14 and
15 are firmly attached.
IBM Integrated Bluetooth with 56K Modem
(BMDC)
For machine type 2681, 2682, 2683, 2722, 2723, 2724
Following illustrations show the BMDC.
15
14
(continued)
92
ThinkPad R40
Removing and replacing a FRU
17
16
When installing: Make sure that antenna jack 17 is
firmly attached.
Note: When unplugging the Bluetooth antenna jack 17,
do not pull the cable; it might snap. Unplug the jack
by pulling a tab with your fingers.
ThinkPad R40
93
Removing and replacing a FRU
1120 Fan assembly
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
1
3
5
4
2
Step
Screw (quantity)
Torque
1
M2 × 13 mm, Silver (4)
0.294 Nm
(3 kgfcm)
When installing: Make sure that the connector 2 is
firmly attached.
94
ThinkPad R40
Removing and replacing a FRU
1130 CPU
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1120 Fan assembly” on page 94
Note: There are two types of CPU socket. Confirm the
socket type of the computer first.
Rotate the head of the screw (A) in the direction of the
arrow 1 to release the lock; then remove the CPU.
A
1
A'
1'
ThinkPad R40
95
Removing and replacing a FRU
When installing: Place the CPU on the CPU socket (1),
and then rotate the head of the screw
(A) in the direction of arrow 2 to
secure the CPU.
1
A
2
1'
2'
A'
Note: When replacing the CPU, you must replace the
thermal pad FRU 5022BZ4023A also.
96
ThinkPad R40
Removing and replacing a FRU
1140 Bluetooth antenna assembly
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
For machine type 2681, 2682, 2683, 2722, 2723, 2724
Note: Some models do not have the Bluetooth antenna.
1
2
a
1
Step
Screw (quantity)
Torque
1
M2.0 × 3.5 mm, Silver (1)
0.294 Nm
(3 kgfcm)
When installing: Route the Bluetooth antenna cable to fit
firmly inside the cable guides on the
base cover as shown in the figure a.
ThinkPad R40
97
Removing and replacing a FRU
1150 LCD assembly
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1110 Communication daughter card (CDC)” on page 88
1
Step
Screw (quantity)
Torque
1
M2.5 × 8.5 mm, Black (1)
0.294 Nm
(3 kgfcm)
(continued)
98
ThinkPad R40
Removing and replacing a FRU
2
3
Step
Screw (quantity)
Torque
2
M2.5 × 6 mm, Yellow (1)
0.294 Nm
(3 kgfcm)
(continued)
ThinkPad R40
99
Removing and replacing a FRU
6
4
5
6
Step
Screw (quantity)
Torque
4
M2.0 × 3.5 mm, Silver (2)
0.294 Nm
(3 kgfcm)
6
M2.5 × 8.5 mm, Black (4)
0.294 Nm
(3 kgfcm)
(continued)
100
ThinkPad R40
Removing and replacing a FRU
7
7
ThinkPad R40
101
Removing and replacing a FRU
When installing: Make sure that the antenna cables are
routed along the cable holder as shown
in this figure, and then attach the LCD
assembly to the base cover by securing
the screws.
102
ThinkPad R40
Removing and replacing a FRU
1160 Keyboard bezel
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
For machine type 2681, 2682, 2683, 2722, 2723, 2724
1
1
1
2
1
1
2
1
2
Step
Screw (quantity)
Torque
1
M2.5 × 8.5 mm, Black (6)
0.294 Nm
(3 kgfcm)
2
M2.5 × 6 mm, Yellow (3)
0.294 Nm
(3 kgfcm)
(continued)
ThinkPad R40
103
Removing and replacing a FRU
If the ThinkPad computer you are servicing has the touch
pad, detach the connector a before removing the screws.
a
When installing: If the ThinkPad computer you are
servicing has the touch pad, make sure
that the connector a is firmly attached.
(continued)
104
ThinkPad R40
Removing and replacing a FRU
Remove the keyboard bezel in the direction of arrow 2.
2
2
ThinkPad R40
105
Removing and replacing a FRU
For machine type 2684, 2685
1
1
1
2
1
1
2
1
2
Step
Screw (quantity)
Torque
1
M2.5 × 8.5 mm, Black (6)
0.294 Nm
(3 kgfcm)
2
M2.5 × 6 mm, Yellow (3)
0.294 Nm
(3 kgfcm)
(continued)
106
ThinkPad R40
Removing and replacing a FRU
Remove the keyboard bezel in the direction of arrow 2.
2
2
ThinkPad R40
107
Removing and replacing a FRU
1170 Speaker assembly and
microphone cable
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1150 LCD assembly” on page 98
v “1160 Keyboard bezel” on page 103
Note: Some models do not have the Microphone.
Detach the connectors 1, 2, and then remove the
microphone cable.
2
1
3
5
4
Step
Screw (quantity)
Torque
3
M2.5 × 6 mm, Yellow (1)
0.294 Nm
(3 kgfcm)
108
ThinkPad R40
Removing and replacing a FRU
1180 System board
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
v “1160 Keyboard bezel” on page 103
v “1170 Speaker assembly and microphone cable” on
page 108
For machine type 2681, 2682, 2683, 2722, 2723, 2724
v System board with IBM security chip
Note: The security chip a is embedded on the system
board.
a
ThinkPad R40
109
Removing and replacing a FRU
v System board without IBM security chip
Begin by checking the FRU number of the system board,
and be sure to use the correct system board FRU for the
computer. For the FRU numbers, see “Parts list” on page
134.
Important
If the ThinkPad computer you are servicing has the
security chip, mind the following:
v Do not remove the security chip from the
system board. If the security chip is removed by
accident, reinstall it on the system board
immediately. Then make sure that it is firmly fixed
on the system board and does not move easily.
v The security chip cannot be used with any other
system board.
v The system board cannot be used with other
security chip.
v The system board cannot be used without the
security chip.
v When you return the defective system board
FRU, you must check whether the security chip is
firmly attached to the system board. If it is not
embedded, it may not be covered under warranty.
110
ThinkPad R40
Removing and replacing a FRU
For machine type 2684, 2685
v System board without IBM security chip
Begin by checking the FRU number of the system board,
and be sure to use the correct system board FRU for the
computer. For the FRU numbers, see “Parts list” on page
134.
ThinkPad R40
111
Removing and replacing a FRU
For machine type 2681, 2682, 2683, 2722, 2723, 2724
1
1
1a
a
Step
Screw (quantity)
Torque
1
M2.5 × 6 mm, Yellow (2)
0.294 Nm
(3 kgfcm)
1+1a M2.5 × 6 mm, Yellow (3)
0.294 Nm
(3 kgfcm)
1
2
a
Note: To remove the system board, the lever a must be
pulled out.
112
ThinkPad R40
Removing and replacing a FRU
When installing:
v Attach the system board so that the two small
projections on the base cover fit into the holes provided.
v Make sure that the lever a must be pulled out.
2
1
a
Note: When replacing the system board, you must replace
the thermal pad FRU 5022BZ4023A also.
ThinkPad R40
113
Removing and replacing a FRU
For machine type 2684, 2685
1
1
1a
Step
Screw (quantity)
Torque
1
M2.5 × 6 mm, Yellow (2)
0.294 Nm
(3 kgfcm)
1+1a M2.5 × 6 mm, Yellow (3)
0.294 Nm
(3 kgfcm)
1
2
114
ThinkPad R40
Removing and replacing a FRU
When installing:
v Attach the system board so that the two small
projections on the base cover fit into the holes provided.
2
1
Note: When replacing the system board, you must replace
the thermal pad FRU 5022BZ4023A also.
ThinkPad R40
115
Removing and replacing a FRU
1190 Hard-disk drive slot
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1070 Backup battery” on page 81
v “1090 PC Card slot assembly” on page 85
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
v “1160 Keyboard bezel” on page 103
v “1170 Speaker assembly and microphone cable” on
page 108
v “1180 System board” on page 109
3
2
1
Step
Screw (quantity)
Torque
1
M2 × 13 mm, Silver (2)
0.294 Nm
(3 kgfcm)
When installing: Make sure that the connector 2 is
firmly attached, and then secure the
screws.
116
ThinkPad R40
Removing and replacing a FRU
2000 Ultrabay Plus guide rail
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
v “1160 Keyboard bezel” on page 103
1
Step
Screw (quantity)
Torque
1
M2.0 × 3.5 mm, Silver (2)
0.294 Nm
(3 kgfcm)
(continued)
ThinkPad R40
117
Removing and replacing a FRU
2
a
1
Step
Screw (quantity)
Torque
1
M2 × 13 mm, Silver (1)
0.294 Nm
(3 kgfcm)
2
M2.0 × 3.5 mm, Silver (1)
0.294 Nm
(3 kgfcm)
When installing: Attach the Ultrabay Plus guide rail so
that the two small projections on the
ultrabay device connector fit into the
holes a provided, and then secure the
screws.
118
ThinkPad R40
Removing and replacing a FRU
2010 I/O Bracket
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1020 Ultrabay Plus device” on page 65
v “1030 Hard-disk drive” on page 66
v “1040 DIMM” on page 68
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
v “1160 Keyboard bezel” on page 103
v “1180 System board” on page 109
v “2000 Ultrabay Plus guide rail” on page 117
1
2
Step
Screw (quantity)
Torque
1
Hex stud (4)
0.294 Nm
(3 kgfcm)
ThinkPad R40
119
Removing and replacing a FRU
2020 LCD front bezel
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
After removing screws 1 and detach all of the latches
2 to 6 in order.
6
1
2
3
4
5
Step
Screw (quantity)
Torque
1
M2.5 × 6 mm, Yellow (2)
0.294 Nm
(3 kgfcm)
When installing: Make sure that all of the latches of the
LCD front bezel are firmly attached to
the LCD cover.
120
ThinkPad R40
Removing and replacing a FRU
2030 Inverter card
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
v “2020 LCD front bezel” on page 120
1
2
3
Step
Screw (quantity)
Torque
1
M2.5 × 5 mm, Black (2)
0.294 Nm
(3 kgfcm)
When installing: Make sure that connectors 2 and 3
are firmly attached.
Cable routing: When replacing the inverter card, route
the connector cable as in the following
figure:
ThinkPad R40
121
Removing and replacing a FRU
2040 LCD panel and LCD cable
assembly
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
v “2020 LCD front bezel” on page 120
v “2030 Inverter card” on page 121
2
1a
1
2
1
Step
Screw (quantity)
Torque
1
M2.5 × 5 mm, Black (2) 13 and 14
inch
0.343 Nm
(3.5 kgfcm)
1+1a M2.5 × 5 mm, Black (3) 15 inch
0.343 Nm
(3.5 kgfcm)
2
0.196 Nm
(2 kgfcm)
M2.0 × 4.0 mm, Black (4)
(continued)
122
ThinkPad R40
Removing and replacing a FRU
4
2
3
When installing the LCD panel, do the following:
v Place the FPC connector under the black antenna
cable.
v Make sure that the antenna cables are firmly routed to
fit to the cable guides of the LCD cover.
v Make sure that the antenna cables are not pinched
under the LCD panel.
ThinkPad R40
123
Removing and replacing a FRU
2050 Antenna assembly, hinges, and
LCD cover
For access, remove these FRUs, in order:
v “1010 Battery pack” on page 64
v “1050 Mini PCI adapter” on page 70
v “1060 Keyboard” on page 73
v “1100 Hinge cover” on page 87
v “1150 LCD assembly” on page 98
v “2020 LCD front bezel” on page 120
v “2030 Inverter card” on page 121
v “2040 LCD panel and LCD cable assembly” on page
122
1
1
Step
Screw (quantity)
Torque
1
M2.0 × 3.5 mm, Silver (4)
0.196 Nm
(2 kgfcm)
124
ThinkPad R40
Removing and replacing a FRU
To install the antenna assembly, do as follows:
1. Make sure that the antenna assembly and hinges are
firmly attached; there are some projections (a) on the
hinges to fix the antenna assembly into place. And
then, route the gray cable (MAIN) as in this figure.
a
3
3
3
(continued)
ThinkPad R40
125
Removing and replacing a FRU
2. Route the black cable (AUX) as in figures 4 and 5.
4
4
4
5
3. Secure the antenna assembly and hinges with screws
to the LCD cover.
126
ThinkPad R40
Locations
Locations
Front view for 2681, 2682, 2683, 2722,
2723, 2724
1
2
3
4
5
6
7
8
Bluetooth/Wireless LAN status
indicator (on some models)
System status indicators
Power status indicators
Power switch
Ultrabay Plus latch
Ultrabay Plus status indicator
Ultrabay Plus device eject lever
Ultrabay Plus
9
10
11
12
13
14
15
16
Note: The Ultrabay Plus accepts
several storage devices, such
as a CD-ROM, a DVD drive, or
a DVD/CD-RW combo drive,
and also accepts an Ultrabay
Plus carrier.
Built-in microphone
TrackPoint pointing stick
TrackPoint buttons
Touch pad buttons
Touch pad
UltraNav
Access IBM button
Volume control buttons
ThinkPad R40
127
Locations
1
2
16
15
3
4
13
12
14
11
10
9
5
6
7
8
128
ThinkPad R40
Locations
Rear view for 2681, 2682, 2683, 2722,
2723, 2724
1
2
Power status indicators
Bluetooth status indicator (on some
models)
S-Video-out connector
Universal serial bus (USB) connector
Ethernet connector
Modem connector
External-monitor connector
Parallel connector
AC power connector
Security keyhole
3
4
5
6
7
8
9
10
2
1
10
9
8
7
6
5
4
ThinkPad R40
3
129
Locations
Bottom view for 2681, 2682, 2683, 2722,
2723, 2724
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Battery pack
Battery pack latches
DIMM slots
Docking connector
Mini PCI card slot
PC Card slots
PC Card eject buttons
IEEE 1394 (on some models)
USB connector
Stereo headphone jack
Microphone jack
Hard-disk drive
LCD latches
Built-in stereo speakers
3
4
2
5
1
6
13
7
8
14
10
13
11
12
130
ThinkPad R40
9
Locations
Front view for 2684, 2685
1
Wireless LAN status indicator (on
some models)
System status indicators
Power status indicators
Power switch
Optical storage drive in the fixed bay
Built-in microphone
TrackPoint pointing stick
TrackPoint buttons
Access IBM button
Volume control buttons
2
3
4
5
6
7
8
9
10
1
2
10
9
3
4
5
6
8
7
ThinkPad R40
131
Locations
Rear view for 2684, 2685
1
2
3
4
5
6
7
8
Power status indicators
Universal serial bus (USB) connector
Ethernet connector
Modem connector
External-monitor connector
Parallel connector
AC power connector
Security keyhole
1
8
132
7
6
ThinkPad R40
5
4
3
2
Locations
Bottom view for 2684, 2685
1
2
3
4
5
6
7
8
9
10
11
12
Battery pack
Battery pack latches
DIMM slots
Mini PCI card slot
PC Card slots
PC Card eject buttons
USB connector
Stereo headphone jack
Microphone jack
Hard-disk drive
LCD latches
Built-in mono speaker
3
2
4
1
5
11
6
7
12
8
11
9
10
ThinkPad R40
133
Parts list
Parts list
R40 series model matrix
The R40 series includes several models. The following
table summarizes the characteristics of each model, to
help you determine which FRU in the part list meets your
need.
For machine type 2681, 2682, 2683, 2722, 2723, 2724,
2896, 2897
Model
CPU
LCD
Bay
device
Mini PCI
ATI M6 16MB/ Memory 128MB/ HDD 20GB
2681–1Ax
Cel 1.6G
2681–15x
13.3 in,
XGA
CDROM 802.11a/b
Ready
2681–11x
—
2681–13x
DVD
2681–28x
14.1 in,
XGA
2681–25x
Combo
2681–21x
—
2681–23x
DVD
2681–35x, 37x
2681–45x, 4Gx
Cel 1.8G
2681–43x
15 in, XGA
CDROM Ready
14.1 in,
XGA
Combo
2681–4Cx
DVD
CDROM —
2681–4Fx
Ready
2681–5Fx
2681–A1x
Ready
CDROM
15 in, XGA
P4 1.8G
2681–A2x
2681–B1x
2681–C1x, C8x
P4 1.9G
2681–M2x
P4 2.0G
13.3 in,
XGA
CDROM —
14.1 in,
XGA
CDROM
DVD
Ready
2681–M3x
—
2681–J5x
P4 2.2G
2722–22x, 24x
PM 1.3G
Ready
ATI M6 16MB/ Memory 128MB/ HDD 30GB
2681–59x
Cel 1.8G
15 in, XGA
DVD
2681–M1x,
MLx
P4 2.0G
14.1 in,
XGA
CDROM
2681–J7x
P4 2.2G
ATI M6 16MB/ Memory 128MB/ HDD 40GB
134
ThinkPad R40
Ready
Parts list
Model
CPU
LCD
Bay
device
Mini PCI
2681–C3x
P4 1.9G
—
P4 2.0G
14.1 in,
XGA
DVD
2681–M4x
ATI M6 16MB/ Memory 256MB/ HDD 20GB
2681–26x
Cel 1.6G
2681–29x
14.1 in,
XGA
CDROM —
802.11b
2681–24x
DVD
2681–22x
CDROM
2681–41x, 4Ex
Cel 1.8G
2682–4Bx
Ready
2681–44x, 46x
Combo
2681–42x, 4Dx
DVD
2896–4WU
Open
2896–5WU
15 in XGA
2681–57x
2681–BJx
Blank
Bezel
P4 1.8G
2681–B8x
14.1 in,
XGA
Ready
—
2681–B4x, B9x
DVD
2681–BAx,
BBx,
BCx, BDx, B5x
Ready
2681–CNx, C2x P4 1.9G
Combo
2681–CAx
DVD
2681–C9x
—
2681–CEx
Combo
2681–CDx
Ready
15 in, XGA
2681–D9x
DVD
802.11a/b
—
2681–DCx
2682–CAx
Ready
CDROM 802.11b
2681–B7x
2681–DBx
—
Ready
14.1 in,
XGA
ThinkPad R40
135
Parts list
Model
CPU
LCD
Bay
device
Mini PCI
2683–FAx
2682–FAx, F9x
2681–M7x
P4 2.0G
14.1 in,
XGA
DVD
Ready
2682–FEx
Cisco
2896–FZU
Open
2682–G9x
15 in, XGA
2681–F9x, FAx,
MMx
14.1 in,
XGA
2681–F8x, MFx
Ready
CDROM
2681–MCx
—
2681–G8x
15 in, XGA
Ready
2681–G9x, G2x
DVD
2681–GGx
Blank
Bezel
2681–KPx
P4 2.2G
2681–N9x
P4 2.4G
DVD
14.1 in,
XGA
2681–P9x
15 in, XGA
2723–26x, 27x PM 1.3G
2722–2Bx, 29x,
27x
2724–26x
14.1 in,
XGA
CDROM
DVD
2897–22U
Open
2723–2Sx
Cisco
2722–2Px,
2Qx, 2Rx
2723–2Fx
2724–2Fx
802.11b
2897–23U
Combo
2722–2Fx, 2Ux,
2Wx, 2Vx
CDROM
2722–23x, 25x
Ready
2722–47x
15 in, XGA
DVD
ATI M6 16MB/ Memory 256MB/ HDD 30GB
2681–5Ax
Cel 1.8G
15 in, XGA
2681–MPx
P4 2.0G
2681–JCx
P4 2.2G
14.1 in,
XGA
Combo
Ready
—
DVD
2681–J9x
Ready
Cisco
2681–KQx
15 in, XGA
802.11a/b
ATI M6 16MB/ Memory 256MB/ HDD 40GB
2681–61x, 62x
Cel 2.0G
2681–73x
136
ThinkPad R40
14.1 in,
XGA
15 in, XGA
Blank
Bezel
Ready
802.11b
Parts list
Model
CPU
2681–CFx, C6x P4 1.9G
2681–C5x
LCD
Bay
device
Mini PCI
14.1 in,
XGA
Combo
Ready
CDROM
2681–C4x
DVD
2681–D5x
2681–FFx,
M6G, MJx,
MHx
P4 2.0G
15 in, XGA
CDROM
14.1 in,
XGA
Combo
2681–M5x
—
2681–MRx,
MSx
CDROM
2681–MQx
802.11b
2681–FDx,
FCx, MDx,
MNx
DVD
2681–FBx,
M8x, MKx
Ready
2681–F1x
Combo
2681–GFx
15 in, XGA
2681–G3x
2681–K4x,
2682–K4x
—
Ready
DVD
P4 2.2G
Cisco
2682–K2x,
2683–K2x
Ready
2681–J2x, J8x
14.1 in,
XGA
2682–J8x
Combo
2682–JAx
Cisco
2681–JDx
802.11a/b
2681–JBx
802.11b
2681–JQx
DVD
2681–JEx
2722–2Cx
802.11a/b
PM 1.3G
Ready
2722–2Mx, 2Nx
Blank
Bezel
2722–2Jx, 2Hx
Combo
2722–95x
PM 1.4G
2722–9Bx
DVD
Combo
802.11b
ATI M6 16MB/ Memory Open/ HDD Open
ThinkPad R40
137
Parts list
Model
CPU
LCD
Bay
device
Mini PCI
2681–2Ux
Cel 1.6G
14.1 in,
XGA
Open
Ready
2681–3Ux
2681–4Tx
15 in, XGA
Cel 1.8G
14.1 in,
XGA
2681–4Ux
Open
2681–5Ux
2681–MVx
Blank
Bezel
15 in, XGA
P4 2.0G
14.1 in,
XGA
2681–FTx
Blank
Bezel
Open
2681–JTx
P4 2.2G
2722–2Yx
PM 1.3G
ATI M7 32MB/ Memory 256/ HDD 20GB
2681–MAx
P4 2.0G
2896–GZU
2722–39x
14.1 in,
XGA
DVD
15 in, XGA
Ready
Open
PM 1.3G
Ready
2722–59x
2722–A2x
PM 1.4G
14.1 in,
XGA
Combo
ATI M7 32MB/ Memory 256/ HDD 30GB
2681–JKG,
JPG, JMG,
JNG
P4 2.2G
14.1 in,
XGA
2681–JFG, JLG
2722–3Gx
Combo
PM 1.3G
ATI M7 32MB/ Memory 256/ HDD 40GB
138
DVD
ThinkPad R40
Ready
Parts list
Model
CPU
LCD
Bay
device
Mini PCI
2681–DHx
P4 1.9G
15 in, XGA
DVD
Ready
2681–DGx
CDROM 802.11b
2681–DJx
—
2681–DKx
Combo
802.11b
2681–D7x
DVD
Ready
2681–DMx
CDROM —
2681–ELx, EPx
2681–G6x
P4 2.0G
15 in,
SXGA+
Combo
14.1 in,
XGA
Blank
Bezel
2681–F4x
2681–MGx
Combo
2681–F5x
802.11b
2681–F6x,
MEx, MBx
2681–M9x
2682–G5x,
GQx
Ready
DVD
15 in, XGA
2681–G6x,
GHx, GJx
2681–GRx
Ready
Combo
DVD
2682–GHx
2682–GKx
802.11b
2681–GCx,
GFx
CDROM
2681–GEx
Combo
2682–GLx
2681–HPx
2681–HNx
15 in,
SXGA+
DVD
Cisco
Blank
Bezel
Ready
Combo
ThinkPad R40
139
Parts list
Model
CPU
LCD
Bay
device
Mini PCI
2681–JJx, J3x,
JKx, JPx, JMx,
JNx
P4 2.2G
14.1 in,
XGA
DVD
Ready
2681–J6x
CDROM
2681–J4x, JFx,
JLx
Combo
2681–J1x
802.11b
2681–JGx
DVD
2682–KEx
15 in, XGA
2681–K3x
2682–KFx,
KDx, KFx, KKx,
K3x
Ready
2681–KMx
Cisco
2681–KCx,
KLx, PAG
Combo
2681–KNx, K8x
Blank
Bezel
2681–KBx
Combo
2681–KAx
2681–LGx
2681–LSG,
LRG
P4 2.4G
15 in,
SXGA
Ready
15 in,
SXGA+
Ready
802.11b
14.1 in,
XGA
OpenBay
2681–PAx
15 in, XGA
Combo
2681–Q5x,
QDx
15 in,
SXGA
DVD
2681–Q7x
140
802.11b
802.11a/b
2681–LSx, LRx
2681–N8x
Ready
ThinkPad R40
Blank
Bezel
802.11b
Parts list
Model
CPU
LCD
Bay
device
Mini PCI
2724–3Px
2723–3Px, 3Lx
PM 1.3G
14.1 in,
XGA
Combo
802.11a/b
2724–3Xx
2723–3Xx
2897–34U
802.11b
2722–3Jx
Ready
2722–3Cx
DVD
2723–58x,
2722–5Ax, 58x,
5Cx
15 in, XGA
2723–5Tx
Cisco
2722–5Jx, 5Nx
Combo
2897–55U
Open
2897–54U
802.11b
2723–6Lx, 6Px
2724–6Px
15 in,
SXGA+
802.11a/b
2722–6Mx
2723–6Xx
2724–6Xx
2722–A3x
Ready
802.11b
PM 1.4G
2722–A6x
14.1 in,
XGA
Ready
Blank
Bezel
2722–A8x
DVD
2724–B4x
2723–B4x, B5x,
F2x
2722–B4x, B5x
15 in, XGA
2724–BAx
2723–BAx
2722–B7x
802.11b
2723–BSx
2722–BSx
Cisco
2722–B3x, B9x
Combo
2722–B6x
Blank
Bezel
2722–C3x
2722–F2x
PM 1.5G
2722–GAx
Ready
15 in,
SXGA+
Combo
15 in, XGA
DVD
15 in,
SXGA+
Combo
802.11b
Combo
Ready
ATI M7 32MB/ Memory 256MB/ HDD 60GB
2681–JHx
2681–L5x, L6x
2681–L6x
2681–L7x
P4 2.2G
14.1 in,
XGA
15 in,
SXGA+
802.11b
Ready
ThinkPad R40
141
Parts list
Model
CPU
LCD
Bay
device
Mini PCI
2681–P4x
P4 2.4G
15 in, XGA
Blank
Bezel
802.11b
15 in,
SXGA
Combo
2681–Q2x,
QBx, Q3x
2681–QCx
Ready
2681–Q6x
802.11a/b
2897–GWU
PM 1.3G
2723–GBx
2722–GCx,
GBx
PM 1.5G
15 in,
SXGA+
802.11b
2722–GDx
802.11a/b
2722–G3x
Ready
ATI M7 32MB/ Memory Open/ HDD Open
2681–2Tx
Cel 1.6G
14.1 in,
XGA
2681–DTx
P4 1.9G
15 in, XGA
P4 2.0G
14.1 in,
XGA
Blank
Bezel
802.11b
2681–DUx
2681–FUx
—
2681–GUx
Blank
Bezel
P4 2.2G
14.1 in,
XGA
2681–KUx
15 in, XGA
2681–LUx
15 in,
SXGA+
2681–NUx
P4 2.4G
2681–QUx
2722–3Yx
14.1 in,
XGA
15 in,
SXGA+
PM 1.3G
14.1 in,
XGA
2722–5Yx
15 in, XGA
2722–6Yx
15 in,
SXGA+
2722–AYx
PM 1.4G
14.1 in,
XGA
2722–BYx
15 in, XGA
2722–CYx
15 in,
SXGA+
2722–EYx
PM 1.5G
14.1 in,
XGA
2722–FYx
15 in, XGA
2722–GYx
15 in,
SXGA+
142
Open
15 in, XGA
2681–GVx
2681–JUx
Ready
ThinkPad R40
Open
Ready
Parts list
For machine type 2684, 2685
Model
CPU
LCD
Bay
device
Mini PCI
Integrated shared/ Memory 128MB/ HDD 20GB
2684–22x
2685–22x
Cel 1.7G
13.3 in,
XGA
2684–23x
CDROM Open
DVD
2684–43x
14.1 in,
XGA
2684–4Tx, 42x,
4Ux, 46x
CDROM
2684–4Cx
2684–A2x
802.11b
P4 1.8G
2684–A3x
2684–B2x, B6x
13.3 in,
XGA
14.1 in,
XGA
2684–B3x
Open
DVD
CDROM
DVD
Integrated shared/ Memory 256MB/ HDD 20GB
2684–53x
Cel 1.7G
2684–52x, 56x
14.1 in,
XGA
2684–54x, 5Ax
2684–C3x,
C8x, C9x, CVx,
C7x
DVD
Open
CDROM
Combo
P4 1.8G
DVD
2684–C6x
CDROM
2684–CAx
Combo
Integrated shared/ Memory 128MB/ HDD 30GB
2684–GNG,
GLG, GSG,
GUG
Cel 1.8G
14.1 in,
XGA
CDROM Open
Integrated shared/ Memory 256MB/ HDD 30GB
2684–GRG,
GTG
Cel 1.8G
2684–NVG
P4 2.0G
2684–QVG
P4 2.2G
14.1 in,
XGA
Combo
Open
DVD
Integrated shared/ Memory 256MB/ HDD 40GB
2684–65x, 6Bx
Cel 1.8G
2684–C5x
P4 1.8G
14.1 in,
XGA
2684–CFx
Combo
802.11b
CDROM Open
2684–CDx
802.11b
2684–CBx
Combo
Integrated shared/ Memory Open/ HDD Open
2684–8Wx
Cel 1.7G
2684–8Xx
2684–DXx
2684–DWx
14.1 in,
XGA
CDROM Open
Combo
P4 1.8G
CDROM
ThinkPad R40
143
Parts list
Overall
For machine type 2681, 2682, 2683, 2896
26
25
1
24
2
23
3
22
21
4
20
19
a
5
d
b
18
17
16
6
15
7
c
14
13
12
8
11
144
ThinkPad R40
10
9
Parts list
v Each FRU is available for all types or model, unless
specific types or models are specified.
v A CRU (Customer Replaceable Units) is identified by a
single asterisk (*) or two asterisks (**) in the CRU ID
column. An N in the CRU ID column means that the part
is not a CRU. A single asterisk (*) means that the part is
a Tier 1 CRU; two asterisks (**) mean that the part is a
Tier 2 CRU.
Tier 1 CRU:
(Example- Mouse, External Keyboard, and Hard-disk
drive with coin screw)
– NO TOOLS ARE REQUIRED.
– A coin or a thumb screw is acceptable.
– Minimal technical expertise is required.
– Minimal problem determination is required-less than
5 minutes.
Tier 2 CRU:
(Example- Adapter card, ThinkPad memory)
– Up to 4 screws or fasteners have to be removed.
– Some technical experience is required.
– HelpCenter assistance may be used.
– Problem determination can be done by customer,
either on site or with HelpCenter assistance.
(continued)
ThinkPad R40
145
Parts list
No. FRU
P/N
CRU
ID
KBD bezel Middle cover ASM (15 in TFT)
46P3104
N
KBD bezel Middle cover ASM (13/14 in
TFT)
46P3105
N
KBD bezel Upper case (15 in TFT)
91P9153
N
KBD bezel Upper case (13/14 in TFT)
91P9154
N
CD-ROM TEAC CD-224E-C
27L3436
*
CD-ROM LG CRN-8245B
27L4301
*
DVD MKE SR-8177
27L4351
*
DVD Toshiba SD-C2612
92P6035
*
Combo x16x10x8x24 HLDS GCC-4160
08K9820
*
Combo x16x10x8x24 KME UJDA–730
08K9818
*
Combo IV x24x10x8x24 HLDS
GCC-4240N
08K9868
*
Combo IV x24x10x8x24 KME UJDA-740
92P6499
*
a - See “Miscellaneous parts” on page 169.
d
1
2
3
For optional Ultrabay Plus devices, see “Optional FRUs” on
page 174.
4
Ultrabay Plus guide rail assembly
46P3120
N
5
Microphone cable assembly
91P6796
N
6
Communication daughter card (CDC)
26P8477
N
26P8256
N
CDC Modem card
7
I/O bracket
46P3124
N
8
Mini PCI door kit
46P3118
**
9
Main battery Li-Ion Sanyo — W/W
02K7054
*
02K7055
*
02K7058
*
02K7059
*
02K7056
*
02K7057
*
02K7060
*
02K7061
*
10 Backup battery
92P0991
N
Main battery Li-Ion Sanyo — Japan
Main battery Li-Ion Panasonic — W/W
Main battery Li-Ion Panasonic — Japan
11 DIMM door kit
46P3118
**
12 Speaker kit
46P3097
N
13 Lower Case w/ label W/W
—wireless (15 in TFT) M/T 2681
46P3106
N
Lower Case w/ label EMEA
—wireless (15 in TFT) M/T 2681
46P3107
N
146
ThinkPad R40
Parts list
No. FRU
P/N
CRU
ID
13
Lower Case w/ label IIPC
—wireless (15 in TFT) M/T 2681
46P3108
N
Lower Case w/ label Korea
—wireless (15 in TFT) M/T 2681
46P3109
N
Lower Case w/ label Taiwan
—wireless (15 in TFT) M/T 2681
46P3110
N
Lower Case w/ label W/W
—wireless (13/14 in TFT) M/T 2681
46P3111
N
Lower Case w/ label EMEA
—wireless (13/14 in TFT) M/T 2681
46P3112
N
Lower Case w/ label IIPC
—wireless (13/14 in TFT) M/T 2681
46P3113
N
Lower Case w/ label Korea
—wireless (13/14 in TFT) M/T 2681
46P3114
N
Lower Case w/ label Taiwan
—wireless (13/14 in TFT) M/T 2681
46P3115
N
Lower Case w/ label W/W
—wireless (15 in TFT) M/T 2682
91P8569
N
Lower Case w/ label EMEA
—wireless (15 in TFT) M/T 2682
91P8570
N
Lower Case w/ label IIPC
—wireless (15 in TFT) M/T 2682
91P8571
N
Lower Case w/ label Korea
—wireless (15 in TFT) M/T 2682
91P8572
N
Lower Case w/ label Taiwan
—wireless (15 in TFT) M/T 2682
91P8573
N
Lower Case w/ label W/W
—wireless (13/14 in TFT) M/T 2682
91P8574
N
Lower Case w/ label EMEA
—wireless (13/14 in TFT) M/T 2682
91P8575
N
Lower Case w/ label IIPC
—wireless (13/14 in TFT) M/T 2682
91P8576
N
Lower Case w/ label Korea
—wireless (13/14 in TFT) M/T 2682
91P8577
N
Lower Case w/ label Taiwan
—wireless (13/14 in TFT) M/T 2682
91P8578
N
Lower Case w/ label W/W
—wireless (15 in TFT) M/T 2683
91P8579
N
Lower Case w/ label EMEA
—wireless (15 in TFT) M/T 2683
91P8580
N
Lower Case w/ label IIPC
—wireless (15 in TFT) M/T 2683
91P8581
N
Lower Case w/ label Korea
—wireless (15 in TFT) M/T 2683
91P8582
N
Lower Case w/ label Taiwan
—wireless (15 in TFT) M/T 2683
91P8583
N
(continued)
ThinkPad R40
147
Parts list
No. FRU
P/N
CRU
ID
13 Lower Case w/ label W/W
—wireless (13/14 in TFT) M/T 2683
91P8584
N
Lower Case w/ label EMEA
—wireless (13/14 in TFT) M/T 2683
91P8585
N
Lower Case w/ label IIPC
—wireless (13/14 in TFT) M/T 2683
91P8586
N
Lower Case w/ label Korea
—wireless (13/14 in TFT) M/T 2683
91P8587
N
Lower Case w/ label Taiwan
—wireless (13/14 in TFT) M/T 2683
91P8588
N
Lower Case w/ label W/W
—no wireless (15 in TFT) M/T 2681
91P8862
N
Lower Case w/ label IIPC
—no wireless (15 in TFT) M/T 2681
91P8864
N
Lower Case w/ label W/W
—no wireless (13/14 in TFT) M/T 2681
91P8867
N
Lower Case w/ label IIPC
—no wireless (13/14 in TFT) M/T 2681
91P8869
N
Lower Case w/ label Korea
—no wireless (13/14 in TFT) M/T 2681
91P8870
N
Lower Case w/ label Taiwan
—no wireless (13/14 in TFT) M/T 2681
91P8871
N
Lower Case w/ label W/W
—wireless 802.11a/b Lee(15 in TFT) M/T
2681
91P8892
N
Lower Case w/ label W/W
—wireless 802.11a/b Lee(13/14 in TFT)
M/T 2681
91P8893
N
Lower Case w/ label W/W
—wireless 802.11a/b Lee(15 in TFT) M/T
2682
91P8894
N
Lower Case w/ label W/W
—wireless 802.11a/b Lee(13/14 in TFT)
M/T 2682
91P8895
N
Lower Case w/ label W/W
—wireless 802.11a/b Lee(15 in TFT) M/T
2683
91P8896
N
Lower Case w/ label W/W
—wireless 802.11a/b Lee(13/14 in TFT)
M/T 2683
91P8897
N
Lower Case w/ label W/W
(15 in TFT) M/T 2896
13N4998
N
Lower Case w/ label W/W
(13/14 in TFT) M/T 2896
13N4999
N
148
ThinkPad R40
Parts list
No. FRU
P/N
CRU
ID
14
91P6806
N
15 DIMM — 128MB
10K0029
**
DIMM — 256MB
10K0031
**
DIMM — 512MB
10K0033
**
16 802.11b Cisco Wireless Card (Sherman
III) — North America
26P8496
**
802.11b Cisco Wireless Card (Sherman
III) — EMEA
26P8498
**
802.11b Cisco Wireless Card (Sherman
III) — Japan
26P8500
**
802.11b Cisco Wireless Card (Sherman
III) — China
26P8502
**
802.11b Actiontec Wireless Card
(Braxton) W/W
26P8421
**
802.11b Actiontec Wireless Card
(Braxton) for xxA
91P7261
**
802.11a/b Philips Wireless Card (Lee)
— W/W
91P7263
N
802.11a/b Philips Wireless Card (Lee)
— Japan
26P8447
N
802.11a/b Philips Wireless Card (Lee)
— China
91P7265
N
26P8401
N
Planar for P4/Cel M6 w/ security card,
w/o 1394 peak shift
91P7167
N
Planar for P4/Cel M6 w/o security card,
w/ 1394 peak shift
26P8402
N
Planar for P4 M7 w/ security card,
w/ 1394 peak shift
26P8403
N
Planar for P4 M7 w/ security card,
w/o 1394 peak shift
26P8404
N
18 CPU P-4 2.4GHz
91P7764
N
CPU P-4 2.2GHz
91P7763
N
CPU P-4 2.0GHz
91P7762
N
CPU P-4 1.9GHz
91P7761
N
CPU P-4 1.8GHz
91P7760
N
CPU Cel 1.8GHz
91P7766
N
CPU Cel 2.2GHz
91P7768
N
CPU Cel 2.0GHz
91P7767
N
CPU Cel 1.6GHz
26P8416
N
CPU Cel 1.7GHz
91P7765
N
46P3120
N
Bluetooth antenna assembly
depending on the model
17 Planar for P4/Cel M6 w/o security card,
w/o 1394 peak shift
19 Hard-disk guide rail assembly
ThinkPad R40
149
Parts list
No. FRU
P/N
CRU
ID
20 PC card slot (15 in TFT)
46P3100
N
46P3101
N
21 Fan ASM
46P3099
N
22
HDD w/ tray and screws 20GB Hitachi
08K9827
**
HDD w/ tray and screws 20GB Fujitsu
92P6000
**
HDD w/ tray and screws 30GB Hitachi
92P6056
**
HDD w/ tray and screws 30GB Fujitsu
92P6057
**
HDD w/ tray and screws 40GB Hitachi
08K9828
**
HDD w/ tray and screws 40GB Fujitsu
92P6001
**
HDD w/ tray and screws 60GB Hitachi
08K9829
**
HDD w/ tray and screws 60GB Fujitsu
92P6002
**
46P3116
**
46P3117
**
25 Pointing stick cap set
91P8898
*
26 Hinge cap
46P3096
N
— Planar Card M6 Infineon
91P7869
N
— Planar Card M6+ESS Infineon
91P7873
N
— Planar Card M6+1394 Infineon
91P7875
N
— Planar Card M7+ESS+1394
91P7879
N
— Planar Card M7+ESS
91P7881
N
— Modem cable w/o core
91P6798
*
— Cable asm kit, RJ11
46P3098
N
— LG/IBM Logo Kit
91P8903
*
PC card slot (13/14 in TFT)
23 Hard-disk drive cover (15 in TFT)
Hard-disk drive cover (13/14 in TFT)
24 Keyboard** (see “Keyboard” on page 165.)
— Recovery CD (see “Recovery CDs” on page 166.)
— AC adapter (see “AC adapters” on page 172.)
150
ThinkPad R40
Parts list
For machine type 2722, 2723, 2724, 2892, 2893, 2897
26
25
1
24
2
23
3
22
21
4
20
19
a
5
d
b
18
17
16
6
15
7
c
14
13
12
8
11
9
10
ThinkPad R40
151
Parts list
No. FRU
P/N
CRU
ID
KBD bezel Middle cover ASM (15 in TFT)
46P3104
N
KBD bezel Middle cover ASM (13/14 in
TFT)
46P3105
N
KBD bezel Upper case (15 in TFT)
91P9153
N
KBD bezel Upper case (13/14 in TFT)
91P9154
N
CD-ROM TEAC CD-224E-C
27L3436
*
CD-ROM LG CRN-8245B
27L4301
*
DVD MKE SR-8177
27L4351
*
DVD Hitachi GDR-8081N
27L4355
*
DVD Toshiba SD-C2612
92P6035
*
Combo x16x10x8x24 HLDS GCC-4160
08K9820
*
Combo x16x10x8x24 KME UJDA–730
08K9818
*
Combo IV x24x10x8x24 HLDS
GCC-4240N
08K9868
*
Combo IV x24x10x8x24 KME UJDA-740
92P6499
*
a - See “Miscellaneous parts” on page 169.
d
1
2
3
For optional Ultrabay Plus devices, see “Optional FRUs” on
page 174.
4
Ultrabay Plus guide rail assembly
46P3120
N
5
Microphone cable assembly
91P6796
N
6
Communication daughter card (CDC)
CDC Modem card
26P8477
N
Bluetooth/Modem Combo card
91P7259
N
7
I/O bracket
46P3124
N
8
Mini PCI door kit
46P3118
**
9
Main battery Li-Ion Sanyo — W/W
02K7054
*
02K7055
*
02K7058
*
02K7059
*
02K7056
*
02K7057
*
02K7060
*
02K7061
*
10 Backup battery
92P0991
N
11 DIMM door kit
46P3118
**
12 Speaker kit
46P3097
N
13 Lower Case w/ label W/W
—wireless (15 in TFT) M/T 2722
91P9595
N
91P9596
N
Main battery Li-Ion Sanyo — Japan
Main battery Li-Ion Panasonic — W/W
Main battery Li-Ion Panasonic — Japan
Lower Case w/ label W/W
—wireless (13/14 in TFT) M/T 2722
152
ThinkPad R40
Parts list
No. FRU
P/N
CRU
ID
13
Lower Case w/ label EMEA
—wireless (13/14 in TFT) M/T 2722
91P9597
N
Lower Case w/ label IIPC
—wireless (13/14 in TFT) M/T 2722
91P9598
N
Lower Case w/ label Korea
—wireless (13/14 in TFT) M/T 2722
91P9599
N
Lower Case w/ label Taiwan
—wireless (13/14 in TFT) M/T 2722
91P9600
N
Lower Case w/ label W/W
—wireless (13/14 in TFT) M/T 2723
91P9601
N
Lower Case w/ label EMEA
—wireless (13/14 in TFT) M/T 2723
91P9602
N
Lower Case w/ label IIPC
—wireless (13/14 in TFT) M/T 2723
91P9603
N
Lower Case w/ label Korea
—wireless (13/14 in TFT) M/T 2723
91P9604
N
Lower Case w/ label Taiwan
—wireless (13/14 in TFT) M/T 2723
91P9605
N
Lower Case w/ label W/W
—wireless (15 in TFT) M/T 2723
91P9611
N
Lower Case w/ label W/W
—wireless (13/14 in TFT) M/T 2724
91P9606
N
Lower Case w/ label EMEA
—wireless (13/14 in TFT) M/T 2724
91P9607
N
Lower Case w/ label IIPC
—wireless (13/14 in TFT) M/T 2724
91P9608
N
Lower Case w/ label Korea
—wireless (13/14 in TFT) M/T 2724
91P9609
N
Lower Case w/ label Taiwan
—wireless (13/14 in TFT) M/T 2724
91P9610
N
Lower Case w/ label W/W
—wireless (15 in TFT) M/T 2724
91P9612
N
Lower Case w/ label W/W
—wireless 802.11a/b (15 in TFT) M/T
2722
91P9619
N
Lower Case w/ label W/W
—wireless 802.11a/b (13/14 in TFT) M/T
2722
91P9620
N
Lower Case w/ label W/W
—wireless 802.11a/b (15 in TFT) M/T
2723
91P9621
N
Lower Case w/ label W/W
—wireless 802.11a/b (13/14 in TFT) M/T
2723
91P9622
N
Lower Case w/ label W/W
—wireless 802.11a/b (15 in TFT) M/T
2724
91P9623
N
Lower Case w/ label W/W
—wireless 802.11a/b (13/14 in TFT) M/T
2724
91P9624
N
ThinkPad R40
153
Parts list
No. FRU
P/N
CRU
ID
13 Lower case w/ label kit W/W
(15 in TFT) M/T 2722
91P9735
N
Lower case w/ label kit W/W
(13/14 in TFT) M/T 2722
91P9736
N
Lower case w/ label kit W/W
(15 in TFT) M/T 2723
91P9737
N
Lower case w/ label kit W/W
(13/14 in TFT) M/T 2723
91P9738
N
Lower case w/ label kit W/W
(15 in TFT) M/T 2724
91P9739
N
Lower case w/ label kit W/W
(13/14 in TFT) M/T 2724
91P9740
N
Lower case w/ label kit Korea
(15 in TFT) M/T 2722
91P9741
N
Lower case w/ label kit Korea
(13/14 in TFT) M/T 2722
91P9742
N
Lower case w/ label kit Korea
(15 in TFT) M/T 2723
91P9743
N
Lower case w/ label kit Korea
(13/14 in TFT) M/T 2723
91P9744
N
Lower case w/ label kit Korea
(15 in TFT) M/T 2724
91P9745
N
Lower case w/ label kit Korea
(13/14 in TFT) M/T 2724
91P9746
N
Lower Case w/ label W/W
(15 in TFT) M/T 2897
13N5000
N
Lower Case w/ label W/W
(13/14 in TFT) M/T 2897
13N5001
N
14 Bluetooth antenna assembly
depending on the model
91P6806
N
15 DIMM — 128MB
10K0029
**
DIMM — 256MB
10K0031
**
DIMM — 512MB
10K0033
**
DIMM — 1GB
10K0035
**
154
ThinkPad R40
Parts list
No. FRU
P/N
CRU
ID
16 802.11b Wireless Card (Calexico-b)
— W/W
91P7293
**
802.11b Wireless Card (Calexico-b)
— xxA xxC xxG xxK xxS
91P7267
**
802.11b Cisco Wireless Card (Sherman
III)
— North America
26P8496
**
802.11b Cisco Wireless Card (Sherman
III)
— EMEA
26P8498
**
802.11b Cisco Wireless Card (Sherman
III)
— Japan
26P8500
**
802.11b Cisco Wireless Card (Sherman
III)
— China
26P8502
**
802.11a/b Wireless Card (Lee) — W/W
91P7263
**
802.11a/b Wireless Card (Lee) — Japan
26P8447
**
802.11a/b Wireless Card (Lee) — China
91P7265
**
17 Planar for Ban M6 w/ security card,
w/ 1394 peak shift
91P7858
N
Planar for Ban M6 w/ security card,
w/o 1394 peak shift
91P7862
N
Planar for Ban M7 w/ security card,
w/ 1394 peak shift
91P7283
N
Planar for Ban M7 w/ security card,
w/o 1394 peak shift
91P7284
N
CPU Pentium M 1.7GHz
91P7882
N
CPU Pentium M 1.6GHz
91P7217
N
CPU Pentium M 1.5GHz
26P8414
N
CPU Pentium M 1.4GHz
26P8415
N
CPU Pentium M 1.3GHz
91P7216
N
19 Hard-disk guide rail assembly
46P3120
N
20 PC card slot (15 in TFT)
46P3100
N
46P3101
N
21 Fan ASM
46P3099
N
22
HDD w/ tray and screws 20GB Hitachi
08K9827
**
HDD w/ tray and screws 20GB Fujitsu
92P6000
**
HDD w/ tray and screws 30GB Hitachi
92P6056
**
HDD w/ tray and screws 30GB Fujitsu
92P6057
**
HDD w/ tray and screws 40GB Hitachi
08K9828
**
HDD w/ tray and screws 40GB Fujitsu
92P6001
**
HDD w/ tray and screws 60GB Hitachi
08K9829
**
HDD w/ tray and screws 60GB Fujitsu
92P6002
**
18
PC card slot (13/14 in TFT)
ThinkPad R40
155
Parts list
No. FRU
P/N
CRU
ID
23 Hard-disk drive cover (15 in TFT)
46P3116
**
46P3117
**
25 Pointing stick cap set
91P8898
*
26 Hinge cap
46P3096
N
— Modem cable w/o core
91P6798
*
— Cable asm kit, RJ11
46P3098
N
— LG/IBM Logo Kit
91P8903
*
Hard-disk drive cover (13/14 in TFT)
24 Keyboard** (see “Keyboard” on page 165.)
— Recovery CD (see “Recovery CDs” on page 166.)
— AC adapter (see “AC adapters” on page 172.)
156
ThinkPad R40
Parts list
For machine type 2684, 2685
25
24
1
23
2
22
3
21
20
4
19
18
a
5
d
b
17
16
15
6
14
7
c
13
12
8
11
9
10
ThinkPad R40
157
Parts list
No. FRU
P/N
CRU
ID
a - See “Miscellaneous parts” on page 169.
d
1
KBD bezel Middle cover ASM (13/14 in
TFT)
46P3105
N
2
KBD bezel Upper case (13/14 in TFT)
91P9628
N
CD-ROM TEAC CD-224E-C (Bare)
13N6710
*
CD-ROM HLDS CRN-8245B (Bare)
08K9841
*
DVD MKE SR-8177 (Bare)
08K9845
*
DVD Hitachi GDR-8081N (Bare)
08K9847
*
Combo IV x24x10x8x24 TEAC (Bare)
92P6105
*
Combo IV x24x10x8x24 KME UJDA-740
(Bare)
92P6065
*
4
Bay Guide Assembly
91P9640
N
5
Microphone cable assembly
02K6210
N
6
Communication daughter card (CDC)
CDC Modem card
26P8477
N
7
I/O bracket
46P3124
N
8
Mini PCI door kit
91P9638
**
9
Main battery Li-Ion (6cell) Sanyo
92P0987
*
Main battery Li-Ion (6cell) Sanyo
92P0988
*
Main battery Li-Ion (6cell) Panasonic
92P0989
*
Main battery Li-Ion (6cell) Panasonic
92P0990
*
10 Backup battery
92P0991
N
11 DIMM door kit
91P9638
**
12 Speaker kit (mono)
91P8199
N
13 Lower Case w/ label W/W
—wireless (13/14 in TFT) M/T 2684
91P9629
N
91P9630
N
3
Lower Case w/ label W/W
—no wireless (13/14 in TFT) M/T 2684
158
ThinkPad R40
Parts list
No. FRU
P/N
CRU
ID
13 Lower Case w/ label EMEA
—no wireless (13/14 in TFT) M/T 2684
91P9631
N
Lower Case w/ label IIPC
—no wireless (13/14 in TFT) M/T 2684
91P9632
N
Lower Case w/ label Korea
—no wireless (13/14 in TFT) M/T 2684
91P9633
N
Lower Case w/ label Taiwan
—no wireless (13/14 in TFT) M/T 2684
91P9634
N
Lower Case w/ label W/W
—no wireless (13/14 in TFT) M/T 2685
91P9635
N
Lower Case w/ label Taiwan
—no wireless (13/14 in TFT) M/T 2685
91P9636
N
14 DIMM — 128MB
10K0029
**
DIMM — 256MB
10K0031
**
DIMM — 512MB
10K0033
**
802.11b Actiontec Wireless Card
(Braxton)
26P8421
**
16 Planar for P4/Cel w/ Mini PCI
(Planar P/N 91P7268)
91P7270
N
17 CPU P-4 2.2GHz
91P7204
N
CPU P-4 2.0GHz
91P7203
N
CPU P-4 1.9GHz
91P7202
N
CPU P-4 1.8GHz
91P7201
N
CPU Cel 2.0GHz
91P7272
N
CPU Cel 1.8GHz
91P7169
N
CPU Cel 1.7GHz
91P7273
N
CPU Cel 2.4GHz
93P4208
N
CPU Cel 2.2GHz
91P7768
N
15
(continued)
ThinkPad R40
159
Parts list
No. FRU
P/N
CRU
ID
18 Hard-disk guide rail assembly
91P9640
N
19
46P3101
N
20 Fan ASM
46P3099
N
21
HDD w/ tray and screws 20GB Hitachi
08K9827
**
HDD w/ tray and screws 20GB Fujitsu
92P6000
**
HDD w/ tray and screws 40GB Hitachi
08K9828
**
HDD w/ tray and screws 40GB Fujitsu
92P6001
**
HDD w/ tray and screws 60GB Hitachi
08K9829
**
HDD w/ tray and screws 60GB Fujitsu
92P6002
**
Hard-disk drive cover (13/14 in TFT)
46P3117
**
24 Pointing stick cap set
91P8898
*
25 Hinge cap
46P3096
N
— Modem cable w/o core
91P6798
*
— Cable ASM kit, RJ11
91P6803
N
— LGIBM Logo kit
91P8903
*
22
PC card slot (13/14 in TFT)
23 Keyboard** (see “Keyboard” on page 165.)
— Recovery CD (see “Recovery CDs” on page 166.)
— AC adapter (see “AC adapters” on page 172.)
160
ThinkPad R40
Parts list
LCD FRUs
1
5
4
2
3
ThinkPad R40
161
Parts list
13/14 in. TFT
For machine type 2681, 2682, 2683
No.
1
2
3
4
5
FRU
P/N
CRU
ID
LCD Bezel ASM (13 in TFT)
46P3092
N
LCD Bezel ASM (14 in TFT)
46P3091
N
LCD Rear Cover ASM (13/14 in
TFT)-Wireless
91P9157
N
LCD Rear Cover ASM (13/14 in TFT)no Wireless
91P9159
N
LCD Hinge/bracket kit w/ antenna (13/14
in TFT)
46P3094
N
LCD Hinge/bracket kit (13/14 in TFT)
91P8633
N
LCD Cable ASM (13 in XGA, wireless
30P)
08K4069
N
LCD Cable ASM (13 in XGA, no-wireless 91P6791
20P)
N
LCD Cable ASM (14 in XGA, wireless
30P)
08K4068
N
LCD Cable ASM (14 in XGA, no-wireless 91P6790
20P)
N
LCD Inverter/LED card
26P8400
N
LCD Inverter card no-wireless
26P8413
N
LCD Panel ASM 13 in (Tori-Sanyo)
92P6643
N
LCD Panel ASM 13 in (LG)
92P6645/ N
93P5545
LCD Panel ASM 14 in (LG)
11P8283
N
LCD Panel ASM 14 in (Samsung)
11P8364
N
LCD Panel ASM 14 in (DBU)
92P6641
N
LCD Panel ASM 14 in (Hydis)
93P5546
N
For machine type 2722, 2723, 2724
No.
FRU
P/N
CRU
ID
1
LCD Bezel ASM (14 in TFT)
46P3091
N
LCD Rear Cover ASM (13/14 in
TFT)-Wireless
91P9157
N
LCD Hinge/bracket kit w/ antenna (13/14
in TFT)
46P3094
N
LCD Cable ASM (14 in XGA, wireless
30P)
08K4068
N
LCD Inverter/LED card
26P8400
N
2
3
4
162
ThinkPad R40
Parts list
No.
FRU
P/N
CRU
ID
5
LCD Panel ASM 14 in (LG)
11P8283
N
LCD Panel ASM 14 in (Samsung)
11P8364
N
LCD Panel ASM 14 in (DBU)
92P6641
N
LCD Panel ASM 14 in (Hydis)
93P5546
N
FRU
P/N
CRU
ID
LCD Bezel ASM (13 in TFT)
91P9627
N
LCD Bezel ASM (14 in TFT)
91P9626
N
LCD Rear Cover ASM (13/14 in
TFT)-Wireless
91P9157
N
LCD Rear Cover ASM (13/14 in TFT)no Wireless
91P9159
N
LCD Hinge/bracket kit w/ antenna (13/14
in TFT)
46P3094
N
LCD Hinge/bracket kit (13/14 in TFT)
91P8633
N
LCD Cable ASM (13 in XGA, no-wireless 91P6802
20P, w/o Thinklight)
N
LCD Cable ASM (14 in XGA, wireless
30P, w/o Thinklight)
91P6800
N
LCD Cable ASM (14 in XGA, no-wireless 91P6801
20P, w/o Thinklight)
N
LCD Inverter/LED card
26P8400
N
LCD Inverter card no-wireless
26P8413
N
LCD Panel ASM 13 in (Tori-Sanyo)
92P6643
N
LCD Panel ASM 13 in (LG)
92P6645/ N
93P5545
LCD Panel ASM 14 in (LG)
11P8283
N
LCD Panel ASM 14 in (Samsung)
11P8364
N
LCD Panel ASM 14 in (DBU)
92P6641
N
LCD Panel ASM 14 in (Hydis)
93P5546
N
FRU
P/N
CRU
ID
LCD Bezel ASM
46P3090
N
LCD Rear Cover ASM-Wireless
91P9156
N
LCD Rear Cover ASM- no Wireless
91P9158
N
For machine type 2684, 2685
No.
1
2
3
4
5
15 in. TFT
For machine type 2681, 2682, 2683
No.
1
ThinkPad R40
163
Parts list
No.
FRU
P/N
CRU
ID
LCD Hinge/bracket kit w/ antenna
46P3093
N
LCD Hinge/bracket kit
91P8632
N
LCD Cable ASM (XGA, wireless 30P)
08K4067
N
LCD Cable ASM (XGA, no-wireless 20P)
91P6789
N
LCD Cable ASM (SXGA+, wireless 30P)
08K4070
N
LCD Inverter/LED card
26P8400
N
LCD Inverter card no-wireless
26P8413
N
LCD Panel ASM XGA (LGP)
11P8310/ N
92P6694
LCD Panel ASM XGA (Hitachi)
11P8311
N
LCD Panel ASM SXGA+ (Samsung)
11P8312
N
LCD Panel ASM SXGA+ (Hitachi)
11P8313
N
FRU
P/N
CRU
ID
LCD Bezel ASM
46P3090
N
LCD Rear Cover ASM-Wireless
91P9156
N
2
LCD Hinge/bracket kit w/ antenna
46P3093
N
3
LCD Cable ASM (XGA, wireless 30P)
08K4067
N
2
3
4
5
For machine type 2722, 2723, 2724
No.
1
LCD Cable ASM (SXGA+, wireless 30P)
08K4070
N
4
LCD Inverter/LED card
26P8400
N
5
LCD Panel ASM XGA (LGP)
11P8310/ N
92P6694
LCD Panel ASM XGA (Hitachi)
11P8311
N
LCD Panel ASM SXGA+ (Samsung)
11P8312
N
LCD Panel ASM SXGA+ (Hitachi)
11P8313
N
164
ThinkPad R40
Parts list
Keyboard
Language
P/N
(NMB)
P/N
CRU
(Chicony) ID
Arabic
08K4743
08K4771
**
Belgian
08K4740
08K4768
**
Chinese, Traditional
08K4754
08K4782
**
Czech
08K4748
08K4776
**
Danish
08K4737
08K4765
**
Dutch
08K4734
08K4762
**
English, U.K.
08K4732
08K4760
**
English, U.S.
08K4729
08K4757
**
French, Canadian
08K4730/
93P4739
08K4758/
93P4740
**
French, European
08K4733
08K4761
**
German
08K4731
08K4759
**
Greek
08K4750
08K4778
**
Hungarian
08K4749
08K4777
**
Hebrew
93P4713
93P4714
**
Italian
08K4738
08K4766
**
Japanese
08K4753
08K4781
**
Korean
08K4755
08K4783
**
Norwegian
08K4736
08K4764
**
Polish
08K4746
08K4774
**
Portuguese
08K4742
08K4770
**
Russian
08K4744
08K4772
**
Slovakian
08K4752
08K4780
**
Slovenian
08K4751
08K4779
**
Spanish, European
08K4739
08K4767
**
Spanish, Latin American
08K4756
08K4784
**
Swedish or Finnish
08K4735
08K4763
**
Swiss
08K4741
08K4769
**
Turkish
08K4747
08K4775
**
ThinkPad R40
165
Parts list
Recovery CDs
For Windows 2000 Professional
Windows 2000 Professional is preinstalled as the operating
system in some models.
For machine type 2681, 2682, 2683
Language
P/N
CRUID
Arabic
01R8329
*
Chinese, Simplified
01R8620
*
Chinese, Traditional
01R8617
*
Chinese, Traditional (Hong Kong S.A.R.)
01R8623
*
Czech
01R8330
*
Danish
01R8320
*
Dutch
01R8327
*
English, U.K.
01R8318
*
English, U.S.
01R8317
*
Finnish
01R8326
*
French
01R8321
*
German
01R8322
*
Greek
01R8334
*
Hebrew
01R8331
*
Hungarian
01R8335
*
Italian
01R8325
*
Japanese
01R8626
*
Norwegian
01R8328
*
Polish
01R8332
*
Portuguese
01R8319
*
Russian
01R8336
*
Spanish
01R8323
*
Swedish
01R8324
*
Turkish
01R8333
*
166
ThinkPad R40
Parts list
For Windows XP Home Edition
Windows XP Home Edition is preinstalled as the operating
system in some models.
For machine type 2681, 2682, 2683, 2722, 2723, 2724
Language
P/N
CRUID
Arabic
01R8429
*
Chinese, Simplified
01R8621
*
Chinese, Traditional
01R8618
*
Chinese, Traditional (Hong Kong S.A.R.)
01R8624
*
Czech
01R8430
*
Danish
01R8420
*
Dutch
01R8427
*
English, U.K.
01R8418
*
English, U.S.
01R8417
*
Finnish
01R8426
*
French
01R8421
*
German
01R8422
*
Greek
01R8434
*
Hebrew
01R8431
*
Hungarian
01R8435
*
Italian
01R8425
*
Japanese
01R8627
*
Norwegian
01R8428
*
Polish
01R8432
*
Portuguese
01R8419
*
Russian
01R8436
*
Spanish
01R8423
*
Swedish
01R8424
*
Turkish
01R8433
*
ThinkPad R40
167
Parts list
For Windows XP professional
Windows XP Professional is preinstalled as the operating
system in some models.
For machine type 2681, 2682, 2683, 2684, 2685, 2722,
2723, 2724
Language
P/N
CRUID
Arabic
01R8529
*
Chinese, Simplified
01R8622
*
Chinese, Traditional
01R8619
*
Chinese, Traditional (Hong Kong S.A.R.)
01R8625
*
Czech
01R8530
*
Danish
01R8520
*
Dutch
01R8527
*
English, U.K.
01R8518
*
English, U.S.
01R8517
*
Finnish
01R8526
*
French
01R8521
*
German
01R8522
*
Greek
01R8534
*
Hebrew
01R8531
*
Hungarian
01R8535
*
Italian
01R8525
*
Japanese
01R8628
*
Norwegian
01R8528
*
Polish
01R8532
*
Portuguese
01R8519
*
Russian
01R8536
*
Spanish
01R8523
*
Swedish
01R8524
*
Turkish
01R8533
*
168
ThinkPad R40
Parts list
Miscellaneous parts
For machine type 2681, 2682, 2683, 2722, 2723, 2724
FRU
P/N
CRU
ID
Screw kit:
v M2.0 × 3.5 mm, Silver #1 (20)
v M2.0 × 4.5 mm, 0.6T Yellow #0 (5)
v M2.5 × 5 mm, Black #1 (10)
v M2.5 × 6 mm, Silver #1 (15)
v M2.5 × 8.5 mm, Black #1 (15)
v M2.0 × 13 mm, Silver #1 (10)
v HDD M3× 3.5 mm, Black #1 (5)
v Hexa screw (5)
v Packing (1)
46P3125
N
Display Misc parts kit:
v Knob, Display left for all (1)
v Knob, Display right for all (1)
v Spring latch display for all (2)
v Sheet, Decoration front/rear for all (6)
v Packing (1)
46P3119
N
LCD Window Plate kit:
91P8634
N
LCD Rubber kit:
46P3126
N
Base cover Misc parts kit:
v Holder, Knob battery (1)
v Knob, Battery latch (1)
v Spring batt latch (1)
v Foot, rubber rear (2)
v Foot, rubber front (1)
v Knob, C/S bay (1)
v Lever, C/S bay (1)
v Plate, C/S eject bay (1)
v Spring, Knob C/S bay (1)
v Spring, Lever C/S bay (1)
v Door, Card BUS (1)
v Spring C/BUS door (1)
v Lens, C/S bay status (1)
v Lens, Irda (1)
v Spring, Door docking (1)
v Door, Docking shutter upper (1)
v Door, Docking shutter down (1)
v Sheet, Deco bottom (1)
v Sheet, Cushion C/S bay (1)
v Sheet, Magnetic Shield (1)
v Packing (1)
46P3121
N
(continued)
ThinkPad R40
169
Parts list
FRU
P/N
CRU
ID
System miscellaneous parts kit:
v (a) Plate, CDC (1)
v (b) Cable, Modem (1)
v (c) Plate, Thermal Brookdale (1)
v (d) Plate, Thermal Video Chip (1)
v Pad, Thermal for Brookdale (1)
v Pad, Thermal for Video Chip (1)
v Plate, Reinforce HDD (1)
v Label, Caution RTC Battery (1)
v Screw, M2.0 × 4.5 mm, 0.6T Yellow #0 (4)
v Packing (1)
91P8635
N
46P3120
N
Note: Italicized letters in parentheses are
references to the exploded view on page 144.
M/B Misc parts kit:
v Holder, Guide HDD (1)
v Sheet, Insulation under PCMCIA (1)
v Plate A’y, C/S Bay top for P4/Banias (1)
v Sheet, Docking connecter (1)
v Cushion, Under Holder HDD (1)
v Hexa screw (4)
v Screw, M2.0 × 3.5 mm, Silver #1 (1)
v Screw, M2.0 × 13 mm, Silver #1 (3)
v Sheet, Insulation cap (30 × 13) (1)
v Sheet, Insulation cap (40 × 20) (1)
v Packing (1)
170
ThinkPad R40
Parts list
For machine type 2684, 2685
FRU
P/N
CRU
ID
Screw kit:
v M2.0 × 3.5 mm, Silver #1 (20)
v M2.0 × 4.5 mm, 0.6T Yellow #0 (5)
v M2.5 × 5 mm, Black #1 (10)
v M2.5 × 6 mm, Silver #1 (15)
v M2.5 × 8.5 mm, Black #1 (15)
v M2.0 × 13 mm, Silver #1 (10)
v HDD M3× 3.5 mm, Black #1 (5)
v Hexa screw (5)
v Packing (1)
46P3125
N
Display Misc parts kit:
v Knob, Display left for all (1)
v Knob, Display right for all (1)
v Spring latch display for all (2)
v Sheet, Decoration front/rear for all (6)
v Packing (1)
46P3119
N
LCD Window Plate kit:
91P9639
N
Rubber kit:
46P3126
Base cover Misc parts kit:
v Holder, Knob battery (1)
v Knob, Battery latch (1)
v Spring batt latch (1)
v Foot, rubber rear (2)
v Foot, rubber front (1)
v Knob, C/S bay (1)
v Lever, C/S bay (1)
v Spring, Knob C/S bay (1)
v Spring, Lever C/S bay (1)
v Door, Card BUS (1)
v Spring C/BUS door (1)
v Sheet, Deco bottom (1)
v Sheet, Cushion C/S bay (1)
v Sheet, Magnetic Shield (1)
v Packing (1)
91P9641
N
(continued)
ThinkPad R40
171
Parts list
FRU
P/N
CRU
ID
System miscellaneous parts kit:
v (a) Plate, CDC (1)
v (b) Cable, Modem (1)
v (c) Plate, Thermal Brookdale (1)
v (d) Plate, Thermal Video Chip (1)
v Pad, Thermal for Brookdale (1)
v Pad, Thermal for Video Chip (1)
v Plate, Reinforce HDD (1)
v Label, Caution RTC Battery (1)
v Screw, M2.0 × 4.5 mm, 0.6T Yellow #0 (4)
v Packing (1)
91P8635
N
96P9640
N
Note: Italicized letters in parentheses are
references to the exploded view on page 144.
M/B Misc parts kit:
v Holder, Guide HDD (1)
v Sheet, Insulation under PCMCIA (1)
v Cushion, Under Holder HDD (1)
v Hexa screw (4)
v Screw, M2.0 × 3.5 mm, Silver #1 (1)
v Screw, M2.0 × 13 mm, Silver #1 (3)
v Sheet, Insulation cap (30 × 13) (1)
v Sheet, Insulation cap (40 × 20) (1)
v Packing (1)
AC adapters
FRU
P/N
CRUID
AC ADAPTER 72W 2–pins ASTEC
02K6753
*
AC ADAPTER 72W 2–pins Delta
02K6756
*
AC ADAPTER 72W 3–pins ASTEC
02K6751
*
AC ADAPTER 72W 3–pins Delta
02K6754
*
172
ThinkPad R40
Parts list
Telephone cable
FRU
P/N
CRU
ID
Telephone cable (Australia)
27L0467
N
Telephone cable (Austria)
27L0449
N
Telephone cable (BE/BK/BS/BD/BF)
27L0451
N
Telephone cable (DK/DE/PO)
27L0447
N
Telephone cable (FI/NO/NS)
27L0446
N
Telephone cable (France)
27L0443
N
Telephone cable (Germany)
27L0441
N
Telephone cable (Italy)
27L0448
N
Telephone cable (ND/NU)
27L0444
N
Telephone cable (SF/SI/SG/SE)
27L0462
N
Telephone cable (Spain)
27L0450
N
Telephone cable (SW/SU)
27L0445
N
Telephone cable (UK/IR/NZ)
27L0442
N
Telephone cable
(US/CAN/TWN/APS/LA/BRZL)
27L0465
N
ThinkPad R40
173
Parts list
Optional FRUs
Ultrabay Plus devices
For machine type 2681, 2682, 2683, 2722, 2723, 2724
FRU
P/N
CRU
ID
ThinkPad Multi-Burner Ultrabay 2000 Drive
22P7015 *
Diskette drive (TEAC)
08K9606 *
Diskette drive (SONY)
08K9607 *
2nd HDD adapter
08K6067 *
Ultrabay Plus battery, Li-Ion (SANYO)
02K6817 *
Ultrabay Plus battery, Li-Ion (SANYO)
02K6818 *
Ultrabay Plus device carrier
26P9388 *
Ultrabay Plus numeric keypad
19K2056 *
Ultrabay Plus cradle for WorkPad c500
series
26P9389 *
Other optional FRUs
For machine type 2681, 2682, 2683, 2722, 2723, 2724
FRU
P/N
CRU
ID
ThinkPad Mini Dock
67P9011 *
ThinkPad Port Replicator
08N1536 N
ThinkPad Port Replicator II
74P6735 *
AC adapter (2 pin, 120 W), DELTA for
ThinkPad Mini Dock
02K7086 *
AC adapter (2 pin, 120 W), LITEON for
ThinkPad Mini Dock
02K7092 *
AC adapter (3 pin, 120 W), LITEON for
ThinkPad Mini Dock
02K7094 *
AC adapter (3 pin, 120 W), LITEON for
ThinkPad Mini Dock
02K7096 *
Main battery, Li-Ion Option W/W
02K7052 *
Main battery, Li-Ion Sanyo W/W
02K7055 *
Main battery, Li-Ion Panasonic W/W
02K7057 *
Main battery, Li-Ion Option Japan
02K7053 *
Main battery, Li-Ion Sanyo Japan
02K7059 *
Main battery, Li-Ion Panasonic Japan
02K7061 *
For machine type 2684, 2685
FRU
P/N
Main battery Li-Ion (6cell) Option
08K8218 *
174
ThinkPad R40
CRU
ID
Parts list
FRU
P/N
Main battery Li-Ion (6cell) Sanyo
92P0988 *
Main battery Li-Ion (6cell) Panasonic
92P0990 *
ThinkPad R40
CRU
ID
175
Parts list
Common parts list
Tools
Triconnector wrap plug
72X8546
PC test card
35G4703
Audio wrap cable
66G5180
USB parallel test cable
05K2580
Screwdriver kit
95F3598
Torque screwdriver
05K4695
5 mm socket wrench
05K4694
Screwdriver
27L8126
1/4″ Hex, Torx TR7 thru TR10 Tamper Resistant Set
00P6967
Magnetic tipped screwdriver 4″ blade 1/4″ tip
9900712
ThinkPad hardware maintenance diskette version
1.69
Note: Download the file from the following Web site:
http://www.ibm.com/pc/partner/infotips
—
Power cords (system)
IBM power cords for a specific country or region are
usually available only in that country or region:
For 2-pin power cords:
Region
P/N
CRU
ID
Canada, U.S.
13H5264 *
Japan
13H5273 *
Argentina
36L8870 *
For 3-pin power cords:
Region
P/N
CRU
ID
Australia, New Zealand
76H3514 *
U.S., Canada, Thailand
76H3516 *
Italy
76H3530 *
Denmark
76H3520 *
U.K., China (Hong Kong S.A.R.)
76H3524 *
European countries
76H3518 *
India, South Africa
76H3522 *
Israel
76H3532 *
Korea
76H3535 *
China (P.R.C.) (other than Hong Kong S.A.R.) 02K0539 *
176
ThinkPad R40
Parts list
Region
P/N
CRU
ID
Switzerland
76H3528 *
Power cords (ThinkPad Mini Dock)
IBM power cords for a specific country or region are
usually available only in that country or region:
For 2-pin power cords:
Region
P/N
CRU
ID
Canada, U.S.
13H5264 *
Japan
13H5273 *
Argentina
36L8870 *
Brazil
46P2095 *
For 3-pin power cords:
Region
P/N
Australia, New Zealand
76H3514 *
Taiwan, Thailand
76H3516 *
Italy
76H3530 *
Denmark
76H3520 *
U.K., China (Hong Kong S.A.R.)
76H3524 *
European countries
76H3518 *
India, South Africa
76H3522 *
Israel
76H3532 *
Korea
76H3535 *
China (P.R.C.) (other than Hong Kong S.A.R)
02K0539 *
Switzerland
76H3528 *
ThinkPad R40
CRU
ID
177
Notices
Notices
References in this publication to IBM products, programs,
or services do not imply that IBM intends to make these
available in all countries in which IBM operates. Any
reference to an IBM product, program, or service is not
intended to state or imply that only that IBM product,
program, or service may be used. Any functionally
equivalent product, program, or service that does not
infringe any of the intellectual property rights of IBM may
be used instead of the IBM product, program, or service.
The evaluation and verification of operation in conjunction
with other products, except those expressly designated by
IBM, are the responsibility of the user.
IBM may have patents or pending patent applications
covering subject matter in this document. The furnishing of
this document does not give you any license to these
patents. You can send license inquiries, in writing, to the
IBM Director of Licensing, IBM Corporation, 500 Columbus
Avenue, Thornwood, NY 10594, U.S.A.
Trademarks
The following terms are trademarks of the IBM Corporation
in the United States or other countries or both:
Asset ID
IBM
OS/2
ThinkLight
ThinkPad
TrackPoint
Ultrabay
UltraPort
UltraNav
Microsoft, Windows, and Windows NT are trademarks of
Microsoft Corporation in the United States and/or other
countries.
Intel, Pentium, and SpeedStep are trademarks of Intel
Corporation in the United States and/or other countries.
(For a complete list of Intel trademarks, see the legal
information on http://www.intel.com/)
Other company, product, or service names may be the
trademarks or service marks of others.
178
ThinkPad R40
Notices
ThinkPad R40
179
Part Number: 13N6183
Printed in Korea
(1P) P/N: 13N6183
Download PDF