Lenco SCDI-01 Stereo CD Radio Player Instruction manual

ENGLISH FM/AM I/M , 230V , W/CDR-RW , W / AUX , iPOD DOCKING ,
W / O VIDEO & AUDIO OUT ,
SIZE : 525 x 297 MM
Stereo
������� CD
��� Radio
������ Player
������
WITH i-Pod Docking Station
SCDI-01
INSTRUCTION MANUAL
For information and support, www.lenco.eu
SCDI-01 LENCO ENGLISH IM NO RCA 1 1
15/6/2011 14:48:20
WARNING
CLASS 1 LASER PRODUCT
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
This product contains a low power laser device.
Warning: Do not touch the lens.
DO NOT THROW BATTERIES IN FIRE !
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
•
Do not use the unit in places which are extremely hot, cold, dusty, or humid.
•
Place the unit on a flat and even surface.
•
Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by
placing it on a carpet.
ON SAFETY
•
When connecting and disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create hazard.
•
When you are not going to use the unit for a long period of time, disconnect the AC power cord.
ON AC VOLTAGE
•
Before use, check that the rated voltage of your unit matches your local voltage.
ON CONDENSATION
•
When left in a heated room where it is warm and damp, water droplets or condensation may form inside the CD player.
•
When there is condensation inside the unit, the unit may not function normally.
•
Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room up and dry the unit before use.
•
Ensure a minimum distance of 5 cm around the apparatus for sufficient ventilation.
•
Ensure that the ventilation is not impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc..
•
Do not place naked flame sources, such as lighted candles on the apparatus.
•
Take attention to the environmental aspects of battery disposal.
•
Use the apparatus only in moderate climates (not in tropical climates).
•
Do not expose the apparatus to dripping or splashing.
•
Do not place objects filled with liquids, such as vases, on the apparatus.
Should any trouble occur, disconnect the AC power cord and refer servicing to qualified personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightening flash
with arrowhead symbol
within the triangle is a
warning sign alerting
the user of "dangerous
voltage" inside the unit.
ATTENTION : To reduce the risk
of electric shock, do not remove the
cover. There are no user serviceable
parts inside the unit. Refer all servicing
to qualified personnel.
The exclamation point within
the triangle is a warning sign
alerting the user of important
instructions accompanying
the product.
In case of malfunction due to electrostatic discharge, the apparatus has to be reset by disconnecting it from mains supply.
SCDI-01 LENCO ENGLISH IM NO RCA 2 2
15/6/2011 14:48:20
CONTROLS
1.
2.
3.
4.
5.
6.
VOLUME + / - BUTTON
FUNCTION BUTTON
HANDLE
RANDOM / P - BUTTON
REPEAT / P + BUTTON
PROGRAM / MEMORY / CLK - ADJ
BUTTON
7. SNOOZE / SLEEP BUTTON
8. CD DOOR
9. POWER /
STANDBY BUTTON
10. OPEN / CLOSE BUTTON
11. PLAY / PAUSE BUTTON
12. STOP BUTTON
13. TIMER / EQ BUTTON
14. BAND / FOLDER BUTTON
15. F - SKIP BUTTON
B - SKIP BUTTON
16. SPEAKER
17. I - POD UNIVERSAL DOCK AND
CONNECTOR
18. SD / MMC
19. USB SLOT
20. CD DISPLAY
21. AC SOCKET
22. TELESCOPIC ANTENNA
23. AUX. IN JACK
24 PHONES JACK
25. REMOTE SENSOR
26. BATTERY COMPARTMENT
REMOTE CONTROL UNIT
POWER /
I - MENU BUTTON
ST / MONO
I-SELECT BUTTON
BAND/FOLDER BUTTON
ID3 BUTTON
PROGRAM / MEMORY/ CLK - ADJ BUTTON
SNOOZE / SLEEP BUTTON
PEPEAT / P+ / I - UP BUTTON
RANDOM / P- / I - DOWN BUTTON
PLAY/PAUSE
I - POD PLAY BUTTON
STOP / I - POD STOP BUTTON
B - SKIP / I - POD BUTTON
F - SKIP / I - POD BUTTON
TIMER / EQ BUTTON
MUTE BUTTON
VOLUME + BUTTON
VOLUME - BUTTON
SCDI-01 LENCO ENGLISH IM NO RCA 3 3
STANDBY BUTTON
FUNCTION BUTTON
GB 1
15/6/2011 14:48:20
POWER SUPPLY
USING HOUSE CURRENT
Before use, check that the rated voltage of your unit matches
your local voltage.
Note: plug is used as the disconnect device.
the disconnect device shall remain readily operable.
USING BATTERIES
Disconnect the AC power cord from
the AC inlet of the unit. Battery power
is cut automatically by the cord while
it is connected.
When the volume decrease,
or the sound distorts,
replace all of the batteries
with new ones.
To AC socket
To AC outlet
battery door
Back up Batteries for the clock
battery door
Insert 8 UM-2 ( size C ) batteries.
Insert 3 LR03 ( size AAA ) batteries.
TURN on / OFF THE SYSTEM
Press the POWER/ STANDBY button to turn the audio on. To change the audio mode between,
CD , UDISK , SD/MMC , IPOD , AUX and TUNER, press the FUNCTION button while the power is on.
The audio mode will be displayed.
Power will be cut off automatically when the CD, MP3 and USB functions are in stop mode for
15 minutes.
ADJUSTING THE SOUND
Press volume +/- to adjust the volume level.
VOLUME
FOR PRIVATE LISTENING
Plug headphones (ø3.5 mm stereo mini-plug) into the
PHONES jack. When headphones are plugged in, the
speakers will automatically be disconnected.
VOLUME
FUNCTION
TUNER OPERATION
Tuning a RADIO Station
1. Press the FUNCTION button repeatedly
until “TUNER” is shown.
FUNCTION
Selecting FM Stereo/Mono mode
1. To select FM stereo/mono mode, press the STEREO/
MONO button on the remote control.
2. Press the BAND / FOLDER button to
select the desired frequency band ( FM or AM ).
BAND/FOLDER/
I-MENU
2. The “STEREO” icon will be on when the received
station is broadcasted
in Stereo.
3. Press the F - SKIP or
B - SKIP
button as many times as required to
tune into the desired station.
3. To select mono mode, press STEREO / MONO button
again.
4. Press and hold the
F - SKIP or
B - SKIP
button for more than 1 second ,
scanning starts automatically and the tuner will stop at the first receivable broadcast station .
4. The “STEREO” icon will never turn on in FM MONO mode.
5. To stop auto tuning, press the F - SKIP
or B - SKIP button again.
SCDI-01 LENCO ENGLISH IM NO RCA 4 4
GB 2
15/6/2011 14:48:21
FOR BETTER RECEPTION
FM
AM
Radio memory function
1.
2.
3.
4.
5.
6.
Tune to a desired radio station.
Press the PROGRAM / MEMORY / CLK - ADJ. button to enter tuning saving mode.
The “MEMORY” icon will be on.
PROGRAM /
Program number “01” will be flashing on the left hand side.
MEMORY /
Within 10 seconds, press the RANDOM/P- or REPEAT/P+ button to select the
CLK-ADJ.
desired program number.
Press the PROGRAM / MEMORY / CLK - ADJ . button to confirm. If there is no button pressed within 10 seconds, it will exit tuning save mode and the
“MEMORY” icon will be off.
COMPACT DISC PLAYBACK
1.
Press the FUNCTION button
repeatedly until “CD” is
shown on display.
3.
Insert a disc with the label
side facing up.
2.
FUNCTION
CD display
5.
4. Close the CD door, the disc will rotate.
For CD : The total tracks of the disc will show on the display.
For MP3/WMA/USB : The total tracks of the disc and the total number of the folders will be shown on the
display.
TO INTERRUPT PLAYBACK
Press the
PLAY/PAUSE button. Press the button
again to resume playback.
For CD : Track number "001" & "CD" will be shown, the time of the track "00:00" will flash, during normal compact disc playback.
For MP3 : Track number "001" & "MP3" will be shown, the time of the track "00:00" will flash, during
MP3 playback.
For WMA : Track number "001" & "WMA" will be shown, the time of the track "00:00" will flash, during WMA playback.
For USB : Track number "001" & "USB" will be shown, the time of the track "00:00" will flash, during USB playback.
CD display
WMA display
Lift the CD door up, by pressing at the right side of the
CD door.
After disc reading is finished, the disc will be played
automatically. In stop mode, press the
PLAY /
PAUSE button to play the track.
For CD : Track number "001" & "CD" & "00:00" will be shown, during normal compact disc playback.
For MP3 : Track number "F01" & "MP3" & "00:00" will be shown, during MP3 playback.
For WMA : Track number "F01" & "WMA" & "00:00" will be shown, during WMA playback.
For USB : Track number "F01" & "USB" & "00:00" will be shown, during USB playback.
CD display
MP3 display
WMA display
USB display
TO STOP PLAYBACK
Press the STOP button.
MP3 display
For CD : The total number of tracks and time will be shown.
For MP3 : The total number of tracks and folder will be shown.
For WMA : The total number of tracks and folder will be shown.
For USB : The total of tracks and folder will be shown.
USB display
F - SKIP
TO SKIP TO THE BEGINNING OF A TRACK
•
Press either one of the skip buttons according to the desired skip direction.
•
Play/back resumes from the selected track.
•
When the button is pressed twice during playback, the previous track will start again.
•
When the button is pressed once during playback, the next track will be played.
SCDI-01 LENCO ENGLISH IM NO RCA 5 5
GB 3
B - SKIP
15/6/2011 14:48:21
SEARCHING FOR A PASSAGE WITHIN A TRACK
•
Keep the or button pressed during playback, and release the button as soon as you
recognise the desired passage. Then the normal CD playback will resume from this point.
PLAYING TRACKS IN RANDOM ORDER
1.
2.
If the RANDOM
�����������������������������������������������������������������������
/ P - button����������������������������������������������������
is pressed, the tracks on the discs are not played
in consecutive order but in random order. The word RAND appears on the display to provide
a visual reminder that the RAND function has been activated.
Press the RANDOM
����������������������������������������������������
/ P - button���������������������������������
to switch off the RAND function.
REPEAT , REPEAT ALL , REPEAT A B , REPEAT FOLDER PLAYBACK
Press the REPEAT / P + button during stop mode.
For CD : The total number of tracks and time will be shown.
For MP3/WMA/USB: The total number of tracks and folders will be shown.
FOR NORMAL COMPACT DISC PLAYBACK
Mode sequence REPEAT >> REPEAT ALL >> CLEAR.
FOR MP3 / WMA / USB PLAYBACK
Mode sequence REPEAT >> REPEAT ALL >> REPEAT
FOLDER >> CLEAR.
During Repeat 1 mode,
the display shows
During Repeat 1 mode,
the display shows
During Repeat 2 mode,
the display shows
During Repeat 2 mode,
the display shows
During Repeat 3 mode,
the display shows
During Repeat 3 mode,
the display shows
CD display
During Repeat 4 mode,
the display shows
Press REPEAT / P + button during playback.
For CD : The folder tracks number and time will be shown.
For MP3/WMA/USB: The folder tracks number and folder will be shown.
During Repeat 1 mode,
the display shows
During Repeat 1 mode,
the display shows
During Repeat 2 mode,
the display shows
During Repeat 2 mode,
the display shows
During Repeat 3 mode,
the display shows
During Repeat 3 mode,
the display shows
During Repeat 4 mode,
the display shows
During Repeat 4 mode,
the display shows
During Repeat 5 mode,
the display shows
During Repeat 5 mode,
the display shows
CD display
During Repeat 6 mode,
Note on CD-R/RW discs
the display shows
- Because of non-standardized format definition/
production of CD-R/RW, playback quality and performance are not guaranteed.
- Manufacturer is not responsible for the playability of CD-R/RW due to recording conditions,
such as PC performance, writing software, media ability, etc.
- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a malfunction.
- It is recommended to record only audio files on CD-R/RW discs for easy reading.
SCDI-01 LENCO ENGLISH IM NO RCA 6 6
MP3/WMA/USB display
FOR MP3 / WMA / USB PLAYBACK
Mode sequence REPEAT >> A REPEAT >>
A-B REPEAT >> REPEAT ALL >> FOLDER.
FOR NORMAL COMPACT DISC PLAYBACK
Mode sequence REPEAT >> A REPEAT >>
A-B REPEAT >> REPEAT ALL.
MP3/WMA/USB display
GB 4
15/6/2011 14:48:21
PROGRAMMED CD / USB / SD / MMC OPERATION
FOR NORMAL COMPACT DISC PLAYBACK
Programmed playback enables tracks on a disc to be played in a desired order. Up to 20 tracks can be programmed.
PROGRAM /
1. Program mode works in STOP mode only.
MEMORY /
2. Hold the “ PROGRAM / MEMORY / CLK - ADJ. ” button for 2 seconds to enter program mode.
CLK-ADJ.
The “PROG” icon will be turned on. “000 P01” will be shown with “000” flashing. “000”
represents the track number and “P01” represents the program location number.
3. Press the F - SKIP or B - SKIP button to select the required track number.
4. Press the “PROGRAM / MEMORY / CLK -ADJ.” button to confirm the track number. The display will show the next program number “000 P02”. The track number will be flashing again, enter the desired track number.
5. Repeat steps 3 and 4 until all the desired tracks has been programmed or all the program memories have been used. It will loop back to P01 after all the program memories have
been used. The same track number can be programmed more than once.
6. Press the
PLAY / PAUSE button to start playback.
7. Press the STOP button to clear all the programmed tracks.
CD display
FOR MP3/WMA/USB/SD PLAYBACK
Programmed playback enables tracks on a disc to be played in a desired order. Up to 20 tracks can be programmed.
1. Program mode works in STOP mode only.
2. Hold the PROGRAM / MEMORY / CLK - ADJ. button for 2 seconds to enter program mode. The “PROG” icon will PROGRAM /
be turned on. “00 000 P01” will be shown with “00” flashing. “000” represents the track number and
MEMORY /
“P:01” represents the program location number.
CLK-ADJ.
3. Press the
F - SKIP or
B - SKIP button to select the desired folder.
4. Press the PROGRAM / MEMORY / CLK - ADJ. button to enter selected folder number.
5. Press the F - SKIP or B - SKIP button to select the required track number.
6. Press the PROGRAM / MEMORY / CLK - ADJ . button to confirm the track number.
The display will show the next program number “000 P02”. The track number will be
flashing again, enter the desired track number.
7. Repeat steps 3 and 4 until all the desired tracks have been programmed or all the
program memories have been used. It will loop back to P01 after all the program
memories have been used. The same track number can be programmed more
than once.
8. Press the
PLAY / PAUSE button to start playback.
MP3/WMA/USB display
9. Press the STOP button to clear all the programmed tracks.
USB / SD / MMC OPERATION
1. Insert USB / SD / MMC into the USB / SD / MMC input slots of the system.
2. Press the “FUNCTION” button to select USB / SD / MMC mode.
3. The unit will start to read the media and playback will start automatically.
note: The USB connector does not support connection with a USB extension cable and
it is not designed for communication with a computer directly.
The manufacturer is not responsible for the playability of a USB / SD / MMC disk or MP3 player
due to recording conditions, capacity, interface compatibility, etc.
Due to different formats, some USB / SD / MMC disks or MP3 players may take longer time to be read.
FUNCTION
Mute On/Off
Mute on / off is changed cyclically by pushing the MUTE button.
The “mute” mark is on during mute.
Mute will be cancelled when you carry out the following operations.
a. Press the MUTE button again.
b. The Volume is adjusted by the VOL +/- button.
MUTE
PRESET EQ
1.
Press the TIMER / EQ button to select ���������������������������
the following �������������
EQ settings :
- FLAT -> ROCK -> JAZZ -> CLASSIC -> POP -> FLAT. will be shown on the display.
SCDI-01 LENCO ENGLISH IM NO RCA 7 7
TIMER / EQ
GB 5
15/6/2011 14:48:21
1.
2.
3.
4.
5.
-
-
-
1.
2.
1.
2.
TIMER
Press the STANDBY button to go into standby mode.
Press and hold the "TIMER/EQ" button, "TIMER"/ the hour digits will flash.
Press the
skip buttons to set the hour.
Press the "TIMER/EQ" button to confirm, the minutes digits will flash and press
the skip buttons to set the minutes. Press the "TIMER/EQ" button to confirm .
Timer wake up can be selected as UDISK / CD / TUNER / IPOD / SD / MMC by futhur pressing
and press the " TIMER/EQ " button to confirm.
Wake up volume can be selected by pressing the VOLUME +/- button and press the " TIMER/EQ"
button to confirm.
To enable the TIMER function, press the TIMER/EQ button at standby mode and the unit
will turn on at the selected preset times.
TIMER / EQ
ID 3 DISPLAY
���������������������������������������������������������������������������������������������������
Press
the ID3 button on the remote to enter ID3 setting mode and select " ID3 ON " or " ID3 OFF " Song name,Singer name and album name can be displayed cyclically during playing MP3.
Title-song name Artist-singer name Album-Album name
ID3
FOLDER SELECTION
BAND / FOLDER
In STOP mode, press the BAND / FOLDER button to skip to the next folder.
This operation is valid for MP3 / WMA / USB media that has been placed into a folder.
TO SET SLEEP FUNCTION
If you want to fall asleep to music, press andhold
10
20
30
40
the SNOOZE / SLEEP button when the unit is on.
You may adjust the radio or CD player's sleep function to play from 10, 20,
30 up to 90 minutes of music before shutting itself off automatically.
00 = sleep timer off
50
60
70
80
90
00
SLEEP
SNOOZE
During the stop mode
1. Pressing the SNOOZE / SLEEP button������������������������������������������������������
on the remote will turn off the system for 9 minutes.
2. Pls note that the SNOOZE / SLEEP �������������������������������������������������
button�������������������������������������������
will only be functional during TIMER mode.
AUX. IN
An external (auxiliary) audio source (i.e., personal CD player
or MP3 player) can be connected to this unit and heard
through the speakers.
1) Plug one end of the cable (not included) into the AUX IN
socket on the unit.
2) Plug the other end of the cable into the Headphone or Line Out socket of the external source.
3) Press the FUNCTION button repeatedly until “AUX ” ALLB FOL��E� INT�O
�AN��
��OG
U�B �A��� ��� WMA M�3 BA�� EQ ����
�NOOZE TIME� �LEE� MEMO�Y �TE�EO
AUX IN
kHz
MHz
FUNCTION
(Plug the other end into the external
source such as an MP3 player.)
is shown on the display.
Continue to operate the CD or MP3 player as usual. Selections will be heard through the unit's speakers.
SCDI-01 LENCO ENGLISH IM NO RCA 8 8
GB 6
15/6/2011 14:48:22
CLOCK SETTING
Clock setting mode works in stop mode
1. Hold the PROGRAM / MEMORY / CLK - ADJ. button clock mode 12 or 24 hours will flash.
2. Press the
B
�����������������������������������������������������������������������������������
- SKIP �������������������������������������������������������������������������
or
F
������������������������������������������������������������
- SKIP ���������������������������������������������������
button to adjust 24 - hour or 12 - hour clock mode.
3. Press the �������������������������������������������������������������������������������������
PROGRAM / MEMORY / CLK - ADJ.��������������������������������������������������������
button again, the hour digit will flash on the display.
4. Press the ����������������������������������������������������������������
B - SKIP �������������������������������������������������������
or ������������������������������������������
F - SKIP����������������������������������
button to adjust the hour digit.
5. Press the ���������������������������������������������������������������������������������������
PROGRAM / MEMORY / CLK - ADJ.����������������������������������������������������������
button again, the minute digit will flash on the display.
6. Press the ������������������������������������������������������������������
B - SKIP ���������������������������������������������������������
or ��������������������������������������������
F - SKIP �����������������������������������
button to adjust the minute digit.
7. Press the ������������������������������������������������������������������������������������������
PROGRAM / MEMORY / CLK - ADJ. ������������������������������������������������������������
button again, the correct time will be shown on the display.
LISTEN TO iPod AND CHARGING INTERNAL iPod BATTERY
Install the iPod universal dock adapter
1. Select the iPod universal dock adaptor that fits with your iPod model, from the next table. The adapter no. is marked at the back of the adapter.
2. Install the adapter with the two tabs facing the front, by pushing it down in the universal dock at the unit front.
3. To remove the adapter for exchange of the others, Press at the back of the adapter and pull it upward.
Universal dock
Adaptor no.
iPod description
Supplied in this unit
(yes / no)
Capacity
1
3G iPod
10GB, 15GB, 20GB
YES
2
3
3G iPod
iPod mini
30GB & 40GB
20GB
YES
YES
4
5
6
4G iPod & U2 iPod
4G iPod
iPod photo & Color U2 iPod
iPod with color display
iPod photo
iPod with color display
30GB & 40GB
40GB
20GB & 30GB
20GB
40GB & 60GB
60GB
YES
YES
YES
7
YES
Note:
1. Only the universal dock adaptor no. “1”. “2”,… “7” are supplied in this unit and they can be installed in this unit
universal dock.
2. You must have the correct universal dock adaptor in place that fits with your iPod to avoid wobbling, causing poor
electrical contact.
3. Various iPod models can vary in control by SCDI-01.
Listen to iPod ( Controlled by unit ) :
1. With the correct iPod universal dock adaptor installed,
gently dock the iPod (without the protective cover) into
the unit's universal dock.
2. When docked, the Internal iPod battery will be charged
until it is fully charged.
3. Press the FUNCTION button to select iPod mode and the
song will be played automatically.
4. Press the
PLAY / PAUSE / I - POD PLAY button to
playback the music." I - POD " will be shown on the display.
5. Press the
B - SKIP / I - POD OR
F - SKIP /
I - POD button to select the next or previous song.
6. Press the VOLUME + / - button to adjust the volume level.
7. Press the
STOP / I - POD STOP button to stop
playback, iPod will be off.
Note:
- This unit display cannot show any music information
(e.g. song name ) of your iPod. Please view the music
information through your iPod display.
- The iPod can be charged only in on mode.
SCDI-01 LENCO ENGLISH IM NO RCA 9 9
Listen to iPod ( Controlled by remote ) :
Go to iPod menu, full operation for the iPod
1. With the correct iPod universal dock adaptor installed, gently dock the iPod (without the protective cover) into the unit's universal dock.
2. When docked, the Internal iPod battery will be charged until it is fully charged.
3. Press the FUNCTION button to select iPod mode
4. Press the I - MENU button to enter the iPod menu
control status.
5. Press the I - SELECT button to forward the selection and
playback the music.
6. Press the I - MENU button to backward the selection.
7. Press the I - UP or I - DOWN button to select the desired file.
8. Press the VOLUME + / - button to adjust the volume level.
9. Press the
PLAY / PAUSE / I - POD PLAY button to
playback the music." I - POD " will be shown on the display.
10.Press the
B - SKIP / I - POD OR
F - SKIP /
I - POD button to select the next or previous song.
11. Press the
STOP / I - POD STOP button to stop playback, iPod will be off.
GB 7
15/6/2011 14:48:22
MAINTENANCE
CLEANING CD
If the CD skips or will not play, the disc may need cleaning.
Before playing, wipe the disc from the centre out with a
cleaning cloth. After playing, store the disc in its case.
CLEANING THE UNIT
Do not use volatile chemicals
on this unit. Clean by lightly
wiping with a soft cloth.
CLEANING THE CD LENS
If the CD lens is dusty, clean it with a brush-blower. Blow
several times on the lens and remove the dust with the
brush. Finger prints may be removed with a cotton swab
moistened with alcohol.
WARNING
Should the CD door be opened before the reading of the CD
is completed, a jamming noise may occur. This is resolved
by closing the CD door.
IMPORTANT NOTE
If an abnormal display indication or an operating problem
occurs, disconnect the AC power cord and remove the
batteries. Wait at least 5 seconds, then reconnect the AC
power cord or reinstall the batteries.
SPECIFICATIONS
CD SECTION
Channels:
S / N ratio:
Wow & Flutter: Sampling frequency:
Quantization:
Pick up light source: Pick up wave length
2 channels
60 dB
undetectable
44.1 kHz 8 x over sampling
1 bit DA converter
Semi - conductor laser
790 nm
RADIO SECTION
Tuning ranges :
FM 87.5 - 108 MHz
AM 522 - 1620 kHz
Antennas :
AM Built - in ferrite bar
FM telescopic antenna
GENERAL
Output power:
2 W + 2 W (RMS)
Power consumption:
15 W
Speaker: 3" 8 OHM
Phones jack:
3.5 MM
AUX IN jack
3.5 MM
Power source: AC: 230V ~ 50Hz
DC: 12V 1.5 x 8 UM2 / LR14 / "C" SIZE
Clock back up Battery
1.5 x 3 AAA / LR03
Dimensions:
Main unit
438 (L) x 262 (D) x 143 (H) mm
Remote control :
35 (L) x 18 (D) x 190 (H) mm
Weight
2.7KGS
Due to continuing improvement, the features and the design are subject to change without notice.
Where to place the item :
Today’s furniture is coated with a wide variety of lacquers and synthetic-coatings that are treated with an extensive range
of cleaning products. Therefore, the possibility that some of these substances contain components that react adversely to
the rubber feet of the item and soften them, cannot be completely excluded. The rubber feet of the appliance can cause
discoloring to furniture surfaces. If necessary, place the appliance on a non-slide surface. If at any time in the future you should need to dispose of this product please note that: Waste electrical products
should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive)
For information and support, www.lenco.eu
SCDI-01 LENCO ENGLISH IM NO RCA 10 10
GB 8
15/6/2011 14:48:22
">