Critikon | Dinamap BP | Service manual | Critikon Dinamap BP Service manual

GE Healthcare
CARESCAPE™ V100 Vital Signs Monitor
Service Manual
Silence
Systolic
HIGH
ADULT
LOW
Alarms
Diastolic
Inflate/Stop
MAP/Cuff
NEONATE
HIGH
Cycle
AUTO CYCLE
HISTORY
History
LOW
To clear hold
2 seconds
Menu
INFLATE PRESSURE
ALARM VOLUME
PULSE VOLUME
SpO
Pulse Rate
BATTERY OK
HIGH
LOW
HIGH
LOW
Print
BATTERY LOW
CHARGING
Temperature
On / Off
C
F
CARESCAPE V100 Vital Signs Monitor
English
2037107-002 (CD)
2048724-002 (paper)
© 2010, 2011 General Electric Company.
All rights reserved.
NOTE: The information in this manual applies to CARESCAPE V100 Vital Signs Monitor software version R1.5. Due to
continuing product innovation, specifications in this manual are subject to change without notice.
NOTE: For technical documentation purposes, the abbreviation GE is used for the legal entity name, GE Medical
Systems Information Technologies, Inc.
Listed below are GE Medical Systems Information Technologies, Inc. trademarks. All other trademarks contained herein
are the property of their respective owners.
Ohmeda Oximetry and other trademarks (OxyTip++, PIr, TruSat, TruSignal, TruTrak+) are the property of GE Medical
Systems Information Technologies, Inc., a division of General Electric Corporation. All other product and company names
are the property of their respective owners.
CARESCAPE, CRITIKON, DINALINK, DINAMAP, DURA-CUF and SOFT-CUF Blood Pressure Cuffs, and SuperSTAT are
trademarks of GE Medical Systems Information Technologies, Inc.
Turbo TempTM, Alaris® Tri-Site, and IVAC are trademarks of CareFusion Corporation.
Exergen and TAT-5000 are trademarks of Exergen Corporation.
Cidex® is a trademark of Surgikos, Inc.
Betadine® is a trademark of Purdue-Frederick.
Masimo SET, LNOP, and LNCS are trademarks of Masimo Corporation. Possession or purchase of this device does not
convey any express or implied license to use the device with replacement parts which would, alone, or in combination
with this device, fall within the scope of one or more of the patents relating to the device.
Nellcor, OxiMax, C-LOCK and SatSeconds are trademarks of Nellcor Puritan Bennett.
Bio-Tek and NIBP Pump 2 are trademarks of Bio-Tek Instruments.
T-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
21 November 2011
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . 1-1
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Manual purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Ordering manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Conventions used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
General use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Responsibility of the manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4
Dangers, warnings, cautions, and notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
Product specific hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5
Equipment symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Service requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Equipment ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Related manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
2048723-002D
Service policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service contracts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packing instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insurance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-14
1-14
1-14
1-14
1-15
1-15
1-15
Disposal of product waste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Patient applied parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packaging material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-15
1-16
1-16
1-16
1-16
CARESCAPE V100 Vital Signs Monitor
i
2
Equipment overview . . . . . . . . . . . . . . . 2-1
Equipment description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Product configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Front controls and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Front panel indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Right-side panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Host communication port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
CARESCAPE V100 vital signs monitor connectivity options . . . . . . .2-6
Product compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Overall principles of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
Cuff blood pressure (NIBP) and pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
DINAMAP SuperSTAT algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-9
DINAMAP Classic and auscultatory reference algorithm . . . . . . . 2-11
Reference used to determine NIBP accuracy . . . . . . . . . . . . . . . . . . 2-12
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Alaris temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Exergen temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main board PWA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User interface (UI) board PWA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SpO2 PWA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pneumatics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optical switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
2-14
2-14
2-15
2-15
2-16
2-16
2-16
Installation . . . . . . . . . . . . . . . . . . . . . . . 3-1
Unpacking and preparation for installation . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Powering the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Power sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Main battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
BATTERY OK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
Battery alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
When about 45 minutes of main battery charge remains: . . . . . . . .3-3
ii
CARESCAPE V100 Vital Signs Monitor
2048723-002D
When about 5 minutes of main battery charge remains: . . . . . . . . .3-4
When 5 minutes of main battery charge expires: . . . . . . . . . . . . . . . .3-4
After plugging the monitor into DC power: . . . . . . . . . . . . . . . . . . . . . .3-4
E13 BATTERY LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
Configuring the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Clinical mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Configuration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
Advanced configuration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Service mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Host communication connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DB15 connector pin assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
3-15
3-16
3-16
3-16
Maintenance . . . . . . . . . . . . . . . . . . . . . 4-1
Preventative maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Maintenance schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Integrity of hoses and cuffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Cleaning schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Cleaning the monitor, monitor accessories, and the Exergen
temporal scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
Cleaning and disinfecting blood pressure cuffs . . . . . . . . . . . . . . . . . .4-5
Cleaning the exterior surfaces of the Alaris temperature devices .4-6
SpO2 sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Long-term storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Battery care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
Main battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
Exergen temporal scanner battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Parameter level functional testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIBP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alaris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exergen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ohmeda, Nellcor, and Masimo SpO2 technologies . . . . . . . . . . . . . . . . .
2048723-002D
CARESCAPE V100 Vital Signs Monitor
4-11
4-11
4-11
4-11
4-12
4-12
iii
Calibration procedures and tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parameter test procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIBP tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pneumatic leakage testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure transducer verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure transducer calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overpressure verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Button testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIBP functional test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIBP overpressure verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External DC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature (perform if equipped with Temp module) . . . . . . . . . . . . .
Alaris temperature calibration verification . . . . . . . . . . . . . . . . . . . .
Alaris temperature probe date of manufacture . . . . . . . . . . . . . . . .
Exergen temperature calibration verification . . . . . . . . . . . . . . . . . .
SpO2 (perform only if equipped with SpO2 module) . . . . . . . . . . . . . . . .
Printer output test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-13
4-13
4-14
4-14
4-14
4-15
4-16
4-16
4-17
4-17
4-17
4-18
4-18
4-18
4-19
4-20
4-20
4-21
4-22
Safety testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical safety tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power outlet test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power cord and plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Patient leakage current test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Patient leakage current test (mains voltage on the applied part)
4-23
4-23
4-23
4-24
4-24
4-24
4-25
4-27
Test results form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
5
Troubleshooting . . . . . . . . . . . . . . . . . . 5-1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Alarm code interpretation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
System failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Alarm conditions and error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Error log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3
Procedure to view and print error code history log . . . . . . . . . . . . . . .5-3
Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Exergen-specific error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
iv
CARESCAPE V100 Vital Signs Monitor
2048723-002D
6
Parts lists and drawings . . . . . . . . . . . 6-1
Ordering parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Compatible service parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
NIBP accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
SpO2 - Ohmeda accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9
SpO2 - Nellcor accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
SpO2 - Masimo accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Temperature accessories - Alaris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Temperature accessories - Exergen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
Power accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Printer accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Mounting accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
Connectivity accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
A
Field-replaceable units (FRUs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRU list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRU photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRU main reference guide drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-15
6-15
6-17
6-28
Disassembly/reassembly of FRUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrostatic discharge (ESD) precautions . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor fascia replacement procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor disassembly procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SpO2 board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exergen TAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-36
6-36
6-37
6-39
6-39
6-40
6-41
6-42
6-42
6-43
6-43
6-44
6-44
Technical specifications and default
settings A-1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIBP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-2
A-2
A-3
A-3
A-4
v
Ohmeda SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Nellcor SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7
Masimo SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-13
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-15
Monitor - main battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-15
Exergen temporal scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-15
Default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-16
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-16
NIBP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-16
Ohmeda SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-16
Nellcor SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17
Masimo SpO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17
Pulse rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17
Alaris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-17
Exergen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-18
B
Appropriate use of NIBP simulators . B-1
Appropriate use of NIBP simulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NIBP accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clinical vs. simulator readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What do simulator manufacturers say? . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Why use simulators? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C
Electromagnetic compatibility (EMC) C-1
Electromagnetic compatibility (EMC): CARESCAPE V100 monitor . . . . .
Guidance and manufacturer’s declaration – electromagnetic
emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guidance and manufacturer’s declaration – electromagnetic
immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended separation distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compliant cables and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi
B-2
B-2
B-2
B-3
B-4
B-4
CARESCAPE V100 Vital Signs Monitor
C-2
C-2
C-3
C-5
C-6
2048723-002D
1
2048723-002D
Introduction
CARESCAPE V100 Vital Signs Monitor
1-1
Introduction: Revision history
Revision history
Each page of this manual has a revision letter located at the bottom of the page.
This letter identifies the revision level of the entire manual. This may be important
if you have different manuals and you do not know which is the most current.
For the initial release, all pages have the revision letter A. For the second update,
all pages receive the revision letter B. The latest letter of the alphabet added to
the table below corresponds to the most current revision.
Revision
Comment
A
Initial release of the manual
B
Updated field-replaceable unit information.
C
Updated field-replaceable unit information and added
content enhancements.
D
Revised manual to reflect revised addendum pn 2001005202C. There are no content changes in the manual itself.
Manual purpose
This manual supplies technical information for service representatives and
technical personnel so they can maintain the equipment to the assembly level.
Use it as a guide for maintenance and electrical repairs considered field
repairable. Where necessary the manual identifies additional sources of relevant
information and technical assistance. See the operator's manual for the
instructions necessary to operate the equipment safely in accordance with its
function and intended use.
Intended audience
This manual is intended for service representatives and technical personnel who
maintain, troubleshoot, or repair this equipment.
Ordering manuals
A paper copy of this manual will be provided upon request. Contact your local GE
representative and request the part number on the first page of the manual.
1-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Introduction: Conventions used in this manual
Conventions used in this manual
Within this manual, special styles and formats are used to distinguish between
terms viewed on screen, a button you must press, or a list of menu commands
you must select:

For technical documentation purposes, the abbreviation GE is used for the
legal entity names, GE Medical Systems Information Technologies, Inc.

In this manual, the CARESCAPE V100 vital signs monitor is referred to as the
monitor.

Names of hardware keys on the equipment are written in bold typeface:
Inflate/Stop.

Menu items are written in bold italic typeface: Monitor Setup.

Emphasized text is in italic typeface.

Menu options or control settings selected consecutively are separated by
the > symbol: Procedures > Cardiac Output.

When referring to different sections in this manual, section names are
enclosed in double quotes: “Maintenance.”

The word “select” means choosing and confirming.

Messages (alarm messages, informative messages) displayed on the screen
are written inside single quotes: 'Learning.'

Note statements provide application tips or other useful information.

All illustrations in this manual are provided as examples only. They may not
necessarily reflect your monitoring setup or data displayed on your monitor.

Any names appearing in examples and illustrations are fictitious. The use of
any real person’s name is purely coincidental.

The monitor is intended to monitor one patient at a time in a clinical setting.
Intended use
General use
CAUTION
Federal law (U.S.A.) restricts this device to sale by or on the
order of a physician.
2048723-002D

To ensure patient safety, use only parts and accessories manufactured or
recommended by GE. Parts and accessories used shall meet the
requirements of IEC 60601-1.

Disposable devices are intended for single use only. They should not be
reused.

Periodically, and whenever the integrity of the monitor is in doubt, test all
functions.
CARESCAPE V100 Vital Signs Monitor
1-3
Introduction: Safety information
Safety information
The information presented in this section is important for the safety of both the
patient and operator. This chapter describes how the terms Danger, Warning,
Caution, and Note are used throughout the manual. In addition, standard
equipment symbols are defined.
Responsibility of the manufacturer
GE is responsible for the effects on safety, reliability, and performance only if:

assembly operations, extensions, readjustments, modifications, or repairs
are carried out by persons authorized by GE;

the electrical installation of the relevant room complies with the
requirements of appropriate regulations; and

the monitor is used in accordance with the instructions of use.
General
This device is intended for use under the direct supervision of a licensed health
care practitioner.
This device is not intended for home use. Federal law (U.S.A.) restricts this device
to be sold by or on the order of a physician.
Contact GE for information before connecting any devices to the equipment that
are not recommended in this manual.
Parts and accessories used must meet the requirements of the applicable IEC/
EN 60601 series safety standards, and/or the system configuration must meet
the requirements of the IEC 60601-1-1 medical electrical systems standard.
Periodically, and whenever the integrity of the device is in doubt, test all
functions.
The use of accessory equipment not complying with the equivalent safety
requirements of this equipment may lead to a reduced level of safety of the
resulting system. Consideration relating to the choice shall include:

use of the accessory in the patient vicinity; and

evidence that the safety certification of the accessory has been performed
in accordance to the appropriate IEC 60601-1 and/or IEC 60601-1-1
harmonized national standard.
If the installation of the equipment, in the U.S.A., will use 240V rather than 120V,
the source must be a center-tapped, 240V, single-phase circuit.
1-4
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Introduction: Safety information
Dangers, warnings, cautions, and notes
The terms Danger, Warning, Caution and Note are used throughout this manual
to point out hazards and to designate a degree or level or seriousness.
Familiarize yourself with their definitions and significance. Hazard is defined as a
source of potential injury to a person.
DANGER indicates a hazardous situation that, if not avoided, will result in death
or serious injury.
WARNING indicates a potential hazard or unsafe practice which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in
minor or moderate injury.
NOTE provides application tips or other useful information to assure that you get
the most from your equipment.
Product specific hazards
DANGER
Do not service the battery while the monitor is connected to
external power.
WARNING
Do not immerse the monitor in water. If the monitor is splashed
with water or becomes wet, wipe it immediately with a dry
cloth.
WARNING
Do not immerse sensors in water, solvents, or cleaning
solutions (the sensors and connectors are not waterproof).
WARNING
Do not perform any testing or maintenance on a sensor while it
is being used to monitor a patient.
WARNING
Place the monitor on a rigid, secure surface or use the monitor
with mounting hardware, poles, and stands recommended by
GE.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
1-5
Introduction: Safety information
WARNING
Only use the monitor in areas where adequate ventilation
exists.
WARNING
Arrange the external AC/DC power converter, air hoses, and all
cables carefully so they do not constitute a hazard.
WARNING
If powering the monitor from an external power adapter or
converter, use only GE-approved power adapters and
converters.
WARNING
The speaker is tested during unit power-up. If the power-up
tones are not heard, audible alarms will also not be heard.
WARNING
If the Power-On Self Test fails, do not use the monitor.
WARNING
Inspect the device for damage prior to use.
WARNING
Do not disassemble, modify, or destroy the battery. Doing so
can cause battery fluid leakage, heat generation, fire, and/or
explosion.
WARNING
Do not incinerate the battery or store it at high temperatures.
Doing so may cause the battery to explode.
1-6
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Introduction: Safety information
WARNING
Do not short-circuit the battery terminals by directly
connecting the metal terminals together. Be certain that no
metal objects (e.g., coins, paper clips, etc.) touch both battery
terminals simultaneously. Doing so can cause the battery to
overheat and/or explode, resulting in possible caustic burns
and/or battery damage.
WARNING
Do not use any battery other than a GE-recommended battery.
Other batteries may not provide the same operating time and
may cause unexpected monitor shutdown. Other batteries
may be incompatible with the internal charger and may cause
battery acid leakage, fire, or explosion.
WARNING
The battery will completely discharge if the monitor is stored
for a prolonged period of time with the battery left inside and
not periodically recharged. Configuration settings may be lost
as a result.
WARNING
Charge the battery pack with the monitor’s internal charger
only. Use of an unrecommended charger may cause battery
fluid leakage, overheating of the battery, and possible
explosion.
WARNING
The electromagnetic compatibility profile of the monitor may
change if accessories other than those specified for use with
the monitor are used. Please refer to the Accessories list
provided with your monitor.
WARNING
Use only accessories approved for use with the monitor. Failure
to use recommended accessories may result in inaccurate
readings.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
1-7
Introduction: Safety information
WARNING
Use of portable phones or other radio frequency (RF) emitting
equipment near the monitor may cause unexpected or adverse
operation.
WARNING
Verify calibration of NIBP parameter (temperature and pulse
oximeter do not require calibration; refer to the “Maintenance”
section for instructions). Ensure that the display is functioning
properly before operating the monitor.
WARNING
Keep the Exergen scanner secured when it is not in use.
WARNING
Failure on the part of the responsible individual, hospital or
institution using this equipment to implement a satisfactory
maintenance schedule may cause undue equipment failure
and possible health hazards.
WARNING
The use of accessories, transducers, and cables other than
those specified may result in increased emissions and/or
increased susceptibility to electromagnetic interference. This
may result in impaired operation of the monitor and/or devices
in the area, leading to inaccurate readings or loss of operation.
CAUTION
To avoid personal injury, do not perform any servicing unless
qualified to do so.
CAUTION
The equipment or system should not be used adjacent to, or
stacked with, other equipment. If adjacent or stacked use is
necessary, the equipment or system should be tested to verify
normal operation in the configuration in which it is being used.
1-8
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Introduction: Safety information
CAUTION
Magnetic and electrical fields are capable of interfering with
the proper performance of the monitor. For this reason make
sure that all external devices operated in the vicinity of the
monitor comply with the relevant EMC requirements.
CAUTION
The monitor does not include any user-replaceable fuses. Refer
servicing to qualified service personnel.
CAUTION
Do not use replacement batteries other than the type supplied
with the monitor. Use only batteries recommended by GE.
Other batteries could result in monitor shutdown. Replacement
batteries are available from GE.
CAUTION
The monitor is designed to conform to Electromagnetic
Compatibility (EMC) standard IEC 60601-1-2 and will operate
accurately in conjunction with other medical equipment which
also meets this requirement. To avoid interference problems
affecting the monitor, do not use the monitor in the presence of
equipment which does not conform to these specifications.
CAUTION
Do not exceed a load weighing 5 lbs. (2.7 kg) in the accessory
basket.
CAUTION
The monitor meets standards IEC 60601-1 and ISO 9919 for
shock and vibration. If the monitor is subjected to conditions
exceeding these standards, performance may be degraded.
CAUTION
The performance of the monitor may be degraded if it is
operated or stored outside of the environmental conditions
specified in this manual.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
1-9
Introduction: Equipment symbols
CAUTION
To prevent cross-contamination, clean exterior surfaces of the
monitor, monitor accessories, and reusable sensors on a
regular basis in compliance with your institution’s infection
control unit and/or biomedical department’s local policy.
CAUTION
Do not sterilize the monitor by irradiation, gas-, heat- or
chemical-based sterilization.
NOTE
This equipment is suitable for use in the presence of electrosurgery.
NOTE
Medical electrical equipment requires special electromagnetic compatibility
(EMC) precautions which must be considered when installing and putting
this equipment into operation. For detailed information, refer to the
Electromagnetic compatibility (EMC) appendix in this manual.
Equipment symbols
The following symbols are associated with the CARESCAPE V100 vital signs
monitor.
NOTE
The model of the monitor determines which symbols appear on it.
Alarms Silence
Atmospheric pressure limitations.
Attention, consult accompanying documents
Battery Power
Classified with respect to electric shock, fire, and
mechanical and other specified hazards only in accordance
with CAN/CSA C22.2 No. 601.1 and UL 2601-1 (UL 60601-1).
Also evaluated to IEC 60601-2-30.
1-10
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Introduction: Equipment symbols
This product conforms with the essential requirements of
the Medical Device Directive 93/42/EEC. Accessories
without the CE mark are not guaranteed to meet the
Essential Requirements of the Medical Device Directive.
Charging
Class II equipment
Consult instructions for use.
Defibrillator-proof type BF equipment
European authorized representative
External communications port connector
External DC power input
Fragile. Handle with care.
Humidity limitations.
IPX0
Ordinary Equipment (Exergen only)
IPX1
This product is protected against vertically falling drops of
water and conforms with the IEC 60529 standard at level of
IPX1. No harmful effects will come of vertically falling drops
of water making contact with the monitor.
Manufacturer: This symbol is accompanied by the name
and the address of the manufacturer.
2048723-002D
Manufacturing Date: This symbol is accompanied by the
date of the manufacturing.
CARESCAPE V100 Vital Signs Monitor
1-11
Introduction: Equipment symbols
CAUTION — Safety ground precaution. Remove power cord
from the mains source by grasping the plug. Do not pull on
the cable.
Catalog or orderable part number.
Russia only. GOST-R mark.
Prescriptive Device. USA only. For use by or on the order of a
Physician, or persons licensed by state law.
Device serial number.
The PSE mark (Product Safety Electric Appliance and
Materials) is a mandatory mark required on Electrical
Appliances in Japan as authorized by the Electrical
Appliance and Material Safety Law (DENAN). This mark
signifies that a product complies with the law according to
a set of standards for electric devices.
Temperature limitations.
WASTE OF ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE): This symbol indicates that the waste of electrical
and electronic equipment must not be disposed as
unsorted municipal waste and must be collected
separately. Please contact an authorized representative of
the manufacturer for information concerning the
decommissioning of your equipment
1-12
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Introduction: Service requirements
Service requirements
Follow the service requirements listed below.

Refer equipment servicing to GE-authorized service personnel only.

Any unauthorized attempt to repair equipment under warranty voids that
warranty.

It is the user’s responsibility to report the need for service to GE or to one of
GE’s authorized agents.

Failure on the part of the responsible individual, hospital or institution using
this equipment to implement a satisfactory maintenance schedule may
cause undue equipment failure and possible health hazards.

Regular maintenance, irrespective of usage, is essential to ensure that the
equipment will always be functional when required.
Equipment ID
Every GE device has a unique serial number for identification. A sample of the
information found on a serial number label is shown below.
### ## ## #### # #
A
B
C
D
E
F
Description
A
product code1
B
year manufactured
C
fiscal week manufactured
D
production sequence number
E
manufacturing site
F
miscellaneous characteristic, indicating prototype, refurbish, etc.
1. The current CARESCAPE V100 Vital Signs Monitor product codes are
SDT or SH6.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
1-13
Introduction: Related manuals
Related manuals
Manual
Title
2010566
Host Communications Reference Manual. Contact your
GE sales representative or distributor.
2048723-001
CARESCAPE V100 Vital Signs Monitor Operator’s Manual
(English). Contact your GE sales representative for
information on other available languages.
Service policy
The warranty for this product is enclosed with the product in the shipper carton.
All repairs on products under warranty must be performed or approved by
Product Service personnel. Unauthorized repairs will void the warranty. Only
qualified electronics service personnel should repair products not covered by
warranty.
Service contracts
Extended warranties can be purchased on most products. Contact your Sales
Representative for details and pricing.
Assistance
If the product fails to function properly, or if assistance, service or spare parts
are required, contact Customer Support. Before contacting Customer Support, it
is helpful to attempt to duplicate the problem and to check all accessories to
ensure that they are not the cause of the problem. If you are unable to resolve
the problem after checking these items, contact GE. Prior to calling, please be
prepared to provide:

product name, model number, and serial number

a complete description of the problem
If repair parts or service are necessary, you will also be asked to provide:

the facility's complete name, address, and account number

a purchase order number if the product needs repair or when you order
spare parts

the facility's GE account number, if possible

the appropriate part number for spare or replacement parts
Service
If your product requires warranty, extended warranty or non-warranty repair
service, contact GE Technical Support or contact your local GE representative. To
facilitate prompt service in cases where the product has external chassis or case
damage, please advise the representative when you call.
1-14
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Introduction: Disposal of product waste
The representative will record all necessary information and will provide a
Return Authorization Number. Prior to returning any product for repair, a Return
Authorization Number must be obtained.
Packing instructions
If you have to return goods for service, follow these recommended packing
instructions.

Remove all hoses, cables, sensors, and power cords from the monitor before
packing.

Pack only the accessories you are requested to return; place them in a
separate bag and insert the bag and the product inside the shipping carton.

Use the original shipping carton and packing materials, if available.

Observe the environmental conditions detailed in the “Specifications” on
page A-2.

It is recommended that all returned goods be insured. Claims for loss or
damage to the product must be initiated by the sender.
If the original shipping carton is not available:

Place the product in a plastic bag and tie or tape the bag to prevent loose
particles or materials from entering openings such as hose ports.

Use a sturdy corrugated container to ship the product; tape securely to seal
the container for shipping.

Pack with at least 4 inches of padding on all sides of the product.
Insurance
Insurance is at the customer's discretion. The shipper must initiate claims for
damage to the product.
Repair parts
To order parts, contact Service Parts at the address or telephone number listed
on the “How To Reach Us...” page found in the front of this manual.
Please allow one working day for confirmation of your order. All orders must
include the following information.

Facility's complete name, address, and phone number

FAX number

Your purchase order number

Your GE account number
Disposal of product waste
As you use the monitor, you will accumulate solid wastes that require proper
disposal or recycling. These include batteries, patient applied parts, and
packaging material. Dispose of these materials according to local or national
regulations.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
1-15
Introduction: Disposal of product waste
Batteries
WARNING
Do not incinerate the battery or expose it to fire or high
temperatures. Doing so may cause the battery to explode.
The sealed, rechargeable main battery contains lead and can be recycled.
The rechargeable battery is of the sealed lead-acid form. Discharge this battery
prior to disposal. Place the battery in packaging which electrically isolates its
contents. Do not puncture or place the battery in a trash compactor. Dispose
any battery in accordance with regional body controlled guideline.
Patient applied parts
Certain patient applied parts, such as those with adhesive (disposable SpO2
sensors), are intended for single use and should be disposed of properly as
medical waste in accordance with regional body controlled guideline.
Other patient applied parts, such as blood pressure cuffs, should be cleaned
according to instructions. Inspect reusable applied parts for wear, replace as
necessary, and dispose of used product as medical waste in accordance with
regional body controlled guideline.
Packaging material
Retain original packaging materials for future use in storing or shipping the
monitor and accessories. This recommendation includes corrugated shippers
and foam/corrugated spacers.
If you decide to dispose of these materials, we recommend recycling them.
Monitor
At the end of its service life, the product described in this manual, as well as its
accessories, must be disposed of in compliance with the guidelines regulating
the disposal of such products. If you have questions concerning disposal of the
product, please contact GE or its representatives.
1-16
CARESCAPE V100 Vital Signs Monitor
2048723-002D
2
2048723-002D
Equipment overview
CARESCAPE V100 Vital Signs Monitor
2-1
Equipment overview: Equipment description
Equipment description
The CARESCAPE V100 vital signs monitor provides a small, portable, easy-to-use
monitoring alternative for sub-acute hospital and non-hospital settings. The
monitor is for use on adult, pediatric, or neonatal patients—one at a time. The
battery-operated monitor offers noninvasive determination of systolic blood
pressure, diastolic blood pressure, mean arterial pressure, pulse rate, oxygen
saturation, and temperature. Monitors are available with or without integrated
printers as well as the following parameters and technologies.

NIBP, Pulse: SuperSTAT, Auscultatory, Classic

SpO2: Ohmeda TruSignal, Nellcor OxiMax, or Masimo SET

Temperature: Alaris Turbo Temp, Alaris Tri-Site, or Exergen
The model of the CARESCAPE V100 vital signs monitor determines which
parameters are in your monitor. Please refer to applicable sections.
Using the CARESCAPE V100 vital signs monitor, a clinician can measure, display,
and record patient vital sign data that is derived from each parameter. The
monitor is also capable of alerting the clinician to changes in the patient’s
condition or when it is unable to effectively monitor the patient’s condition. All of
the main operations of the CARESCAPE V100 vital signs monitor are easy-to-use
and only a button-touch away. Please review the factory default settings and,
where applicable, enter settings appropriate for your use.
Product configurations
Each CARESCAPE V100 vital signs monitor is supplied with an accessory pack.
The contents of the pack vary according to model. Unpack the items carefully. If
an accessory is missing or if an item is in a nonworking condition, contact GE
Customer Service immediately.
It is recommended that all the packaging be retained, in case the monitor must
be returned for service in the future.
2-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Equipment overview: Front controls and connectors
Front controls and connectors
1.
Silence button: mutes audible alarms. Any other active alarm that can be
acknowledged is also cleared and the alarm condition is reset whenever this
key is pressed. When pressed, the alarm silence indicator (bell) lights solid
red to indicate that audible alarms have been silenced for 2 minutes. Alarm
silence can be cancelled by pressing the Silence button again.
2.
Alarms button: used to view or adjust parameter alarm limit settings.
3.
+/- buttons (Plus/Minus): used when you are in the following modes: limit,
menu, cycle, and history.
4.

When you are in limit or menu setting, pressing the +/- button increases
and decreases an adjustable setting.

When you are in cycle or history mode, pressing the +/- buttons
displays the next or previous cycle selection or entry in the history list,
respectively.

When you reach the beginning or ending of a list, a negative key-click
sounds.
Menu button: accesses menu settings that can be adjusted: INFLATE
PRESSURE (ADULT and NEONATE), ALARM VOLUME, and PULSE VOLUME.
(Refer to “Operating modes” on page 3-5 for a description of clinical mode.)
NOTE
ADULT indicator encompasses both adult and pediatric patients.
2048723-002D
5.
SpO2 sensor connector: attach SpO2 cables here.
6.
NIBP connector: attach NIBP cuff hoses here.
7.
Inflate/Stop button: starts a manual NIBP determination or stop any NIBP
determination.
8.
Temperature probe holster: stores Alaris temperature probe.
CARESCAPE V100 Vital Signs Monitor
2-3
Equipment overview: Front panel indicators
9.
Cycle button: used to select NIBP mode of manual, auto cycle, or Stat mode.
10. Temperature probe cover storage: stores Alaris probe covers.
11. History button: activates the history mode to view stored patient data. The
most recent entries are displayed first. Press and hold the button for 2
seconds to clear all entries stored.
12. Print button: prints currently displayed values or all stored entries when in
history mode.
13. On/Off button: controls on/off state of monitor; push for power on and push
again for power off.
14. Alaris temperature probe connector: attach temperature probe cable here.
(The Exergen scanner connects to the host communication port at the back
of the system. Refer to “Rear panel” on page 2-6).
Front panel indicators
Systolic
HIGH
15
16
LOW
Diastolic
MAP/Cuff
24
25
26
27
28
29
ADULT
NEONATE
AUTO CYCLE
HIGH
17
HISTORY
LOW
18
19
20
21
22
23
INFLATE PRESSURE
ALARM VOLUME
PULSE VOLUME
SpO
Pulse Rate
HIGH
LOW
HIGH
LOW
28
30
31
29
32
30
BATTERY OK
CHARGING
Temperature
C
31
33
F
15. Alarm silence indicator:

Solid red: Indicates that an alarm silence is active and the audible alarm
tones are silenced for 2 minutes.

Blinking red (Legacy alarm mode only): Indicates that an alarm silence is
not active and at least one alarm condition is present.
16. Systolic window: indicates measured systolic NIBP in mmHg.
17. Diastolic window: indicates measured diastolic NIBP in mmHg.
18. INFLATE PRESSURE indicator: flashes to indicate you are making a change
to the inflation pressure. Adjustable for adult/ped and neonate patients.
19. ALARM VOLUME indicator: flashes to indicate you are making a change to
the alarm volume.
20. PULSE VOLUME indicator: flashes to indicate you are making a change to
the pulse volume.
2-4
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Equipment overview: Right-side panel
21. Pulse Rate window: shows pulse rate in beats per minute.
22. SpO2 pulse indicator: flashing red LED bar indicates that pulses are being
derived from SpO2 signals.
23. SpO2 window: indicates oxygen saturation in %.
24. MAP/Cuff window: indicates measured mean arterial pressure (MAP) in
mmHg and shows cuff pressure during NIBP determination.
25. ADULT indicator: lights to indicate you are making a change to adult/ped
NIBP limits or inflation pressure settings.
26. NEONATE indicator: lights to indicate you are making a change to neonate
NIBP limits or inflation pressure settings.
27. AUTO CYCLE indicator: lights green to indicate auto mode is the chosen
NIBP mode; flashes to indicate you are making a change to the auto mode.
28. Min window: displays the NIBP mode if manual or Stat as well as the cycle
time when taking auto NIBP determinations.
29. HISTORY indicator: flashes to indicate you are in history mode.
30. BATTERY OK indicator: lights green to indicate the monitor is operating on
battery power and that the battery is sufficiently charged.
31. BATTERY LOW indicator: lights amber to indicate low charge for the battery
(less than 45 minutes when solid; 5 minutes or less when flashing).
32. CHARGING indicator: lights green to indicate presence of external power
source and battery charging.
33. Temperature window: indicates measured temperature.
Right-side panel
1
2048723-002D
CARESCAPE V100 Vital Signs Monitor
2-5
Equipment overview: Rear panel
1.
External DC power socket: used with approved GE AC-DC power converter
only. Refer to “Parts lists and drawings” on page 6-1 for the part number of
the approved power supply.
Rear panel
3
2
2.
Host communication port (15 pin D-type) for use only with equipment
conforming to IEC 60601-1 or configured to comply with IEC 60601-1-1. The
Exergen scanner connects to this port.
NOTES
3.

For connection details, see “Host communication connector” on page 315.

Attach one accessory to this port.
Printer door.
Host communication port
The host communication port is used to interface the CARESCAPE V100 vital
signs monitor with other electronic devices (a central nurse's station or remote
alarm device), or with the Exergen scanner. For further information, reference
the Host Communication manual.
CARESCAPE V100 vital signs monitor connectivity options
The following connectivity options are available for use with the CARESCAPE
V100 vital signs monitor and can be purchased from GE:
2-6

DINALINK™ adapter: The DINALINK adapter is an accessory that connects
the CARESCAPE V100 vital signs monitor to the ApexPro telemetry system,
enabling vital signs to be transmitted to and displayed on a Central Station.

Direct Connection: Isolated adapter cables are used to connect the
CARESCAPE V100 vital signs monitor to general purpose devices, such as a
PC.

DINAWIN Application Programming Interface (API) software: The DINAWIN
API is a software library that can be installed on a PC to facilitate the
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Equipment overview: Product compliance
development of applications exchanging data with the CARESCAPE V100
vital signs monitor.

An interface to the Pyxis Nursing Data Collection mobile clinical data
collection application from CareFusion Corporation.

Remote Alarm Cable: This cable connects the CARESCAPE V100 vital signs
monitor to the hospital’s remote alarm “Nurse Call” system to provide
remote alarming.
For more information, see “Host communication connector” on page 3-15.
GE frequently updates its connectivity accessory offerings. Please contact your
GE sales representative for the latest information on connectivity solutions for
your monitor.
Product compliance
The CARESCAPE V100 vital signs monitor is classified in the following categories
for compliance with IEC 60601-1:

Internally powered or Class II when powered from external supply.

Transportable.

For continuous operation.

Not suitable for use in the presence of flammable anesthetics.

Not for use in the presence of an oxygen-enriched atmosphere (oxygen
tent).

Type BF defibrillation-proof applied parts.

IPX1, degree of protection against ingress of water.

Sterilization/Disinfection, see “Cleaning” on page 4-3.

Software is developed in accordance with IEC 60601-1-4.

The monitor complies to IEC 60601-2-49.

The alarm system is developed in accordance with IEC 60601-1-8.

This equipment is suitable for connection to public mains via power
adapters as defined in CISPR 11.

The SpO2 parameter complies to ISO 9919.

The NIBP parameter complies to IEC 60601-2-30, EN 1060-1, EN 1060-3, and
ANSI/AAMI SP10.

The Temperature parameter complies to ASTM E-1112-00.

Defibrillation protected. When used with the recommended accessories, the
monitor is protected against the effects of defibrillator discharge. If
monitoring is disrupted by the defibrillation, the monitor will recover.

This product conforms with the essential requirements of the Medical
Device Directive 93/42/EEC. Accessories without the CE mark are not
guaranteed to meet the Essential Requirements of the Medical Device
Directive.
Overall principles of operation
This section provides overall theory of operation and functional description of
the monitor.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
2-7
Equipment overview: Overall principles of operation
The monitor is a portable unit that receives power from an internal rechargeable
lead-acid main battery.
When the On/Off button is pressed, the Main Board is brought out of a sleep
mode and turns on the power regulators. The power regulators provide
conditioned power from the main battery. The external DC source is used only to
charge the main battery. Once the monitor is energized, a self-test is performed.
The self-test automatically tests the main functions of the monitor. Failure of the
self-test will set the monitor into a fail-safe mode with an audio alarm.
Under normal operating conditions, the monitor is ready to record the patient
vital signs using three external attachments: the temperature probe, SpO2
sensor, and cuff. Interface with a central station or other device is accomplished
through the host communication port on the back of the monitor.
NOTES

Prior to each use, inspect the power supply cord to ensure proper
connection and condition.

Be sure to unplug the monitor before transport.
SpO2
The SpO2 probe has a built-in sensor. When the SpO2 sensor is attached to the
SpO2 connector and patient, the probe senses both heart rate and oxygen
saturation. The analog signals are routed to the SpO2 Printed Wiring Assemblies
(PWA) for Ohmeda, Nellcor, or Masimo. The analog signals are analyzed on the
SpO2 PWA. The results are digitized and sent to the Main Board via opto
couplers. The couplers provide patient isolation as well as serial data interface.
The Main Board temporarily stores the data and routes it to the UI Board for
display and/or printer.
A reset signal to the SpO2 PWA is also provided so that power up sequencing is
correct. If the SpO2 circuit quits communicating to the Main Board, the Main
Board will attempt to reset the SpO2 PWA.
Cuff blood pressure (NIBP) and pulse
The NIBP parameter in the monitor is available with three types of DINAMAP
NIBP technologies: two calibrated to intra-arterial pressure (Classic and
SuperSTAT) and one calibrated to the auscultatory method (Auscultatory).
Specific technologies are available in select markets. All user interface options,
instructions for use, and alarms will be the same for all technologies. The NIBP
parameter is included in all models. Blood pressure is monitored noninvasively in
the monitor by oscillometric method.
NOTE
For neonatal populations, the reference is always the intra-arterial pressure
monitoring method.
When the cuff and hose are attached to the monitor and a Non-Invasive Blood
Pressure (NIBP) determination is initiated, the pump inflates the cuff. Pressure
transducers PT1 and PT2 monitor pressure information. The pneumatic manifold
2-8
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Equipment overview: Overall principles of operation
has one valve, which is used to deflate the cuff. Valve control is through the Main
Board. When the cuff pressure data acquisition for the determination is
complete, the processor on the Main Board calculates the systolic NIBP, the
diastolic NIBP, the Mean Arterial Pressure (MAP), and the pulse rate. The results
are then displayed on the UI Board and sent to the printer (if the user presses the
Print button).
The Pneumatics are controlled by the NIBP processor. The NIBP processor
monitors pressure information from PT2. If an over-inflation condition occurs,
the OVERPRESSURE signal is routed to the Pneumatics to release the air
pressure. The Main Board also generates an alarm condition with the speaker
sounding and error code message on the UI Board.
DINAMAP SuperSTAT algorithm
The oscillometric method of determining NIBP is accomplished by a sensitive
transducer which measures cuff pressure and pressure oscillations within the
cuff. For the first determination taken on a patient, the algorithm stores the
pattern of the patient's oscillation size as a function of the pressure steps. For
subsequent manual, auto, or Stat determinations taken within 2 minutes of a
previous determination of the same patient, as few as four pressure steps may
be necessary to complete the determination process. In auto mode the data is
stored for up to 16 minutes. When employing fewer pressure steps, the system
uses the stored information from the previous blood pressure determination to
decide the best pressure steps to take. The algorithm measures the consistency
of pulse size to tell if the oscillations taken at a step are good and if more steps
are needed.
The first determination settles at an initial target pressure of 135 mmHg (adult
mode) and 100 mmHg (neonate mode), depending on initial target pressure
preset. To allow for rapid settling of cuff pressure, the monitor will momentarily
inflate to a higher pressure then immediately deflate to the target pressure. After
inflating the cuff, the NIBP parameter begins to deflate. The oscillations versus
cuff pressure are measured to determine the mean pressure and calculate the
systolic and diastolic pressures.
During an NIBP determination, the parameter deflates the cuff one step each
time it detects two pulsations of relatively equal amplitude. The time between
deflation steps depends on the frequency of these matched pulses (pulse rate of
the patient). However, if the monitor is unable to find any pulse within several
seconds, it will deflate to the next step. The process of finding two matched
pulses at each step provides artifact rejection due to patient movement and
greatly enhances the accuracy of the monitor. The figure shows a full
determination sequence for an adult patient. In Stat mode, some steps may
require only one pulse.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
2-9
Equipment overview: Overall principles of operation
Full NIBP determination sequence for adult
(specific pressure values are examples only)
At each step the microprocessor stores cuff pressure, the matched pulse
amplitude, and the time between successive pulses. The stepped deflation and
matched pulse detection continues until diastolic pressure is determined or total
cuff pressure falls below 8 mmHg. The parameter then deflates the cuff (to zero
detected pressure), analyzes the stored data, and updates the screen.
The operating cycle is composed of four parts: inflation time, deflation time,
evaluation time, and wait time. Wait time, which varies from mode to mode, is
affected by the cycle time (auto mode) or operator intervention (manual mode).
The figure shows the basic operating cycle for an NIBP determination.
CUFF PRESSURE
Inflation
Time
Wait Time
Evaluation Time
Deflation Time
Determination Time
Cycle Time
TIME
SuperSTAT NIBP - auto mode
Systolic search
If systolic pressure is not found, the SuperSTAT algorithm can search at cuff
pressures higher than the initial target pressure. The algorithm will inflate above
the initial target pressure to obtain more data in the systolic region. The pressure
is limited to the maximum allowed for the selected patient type.
2-10
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Equipment overview: Overall principles of operation
The SuperSTAT algorithm evaluates the data obtained during the determination,
and the prior determination if it is available, to determine if additional data is
needed to complete the determination. It can then selectively pump to a single
cuff pressure to obtain the data it needs and then return to the existing deflation
sequence. This search process makes SuperSTAT more efficient.
Accuracy of the DINAMAP NIBP measurements was validated against the intraarterial method. Do not use the auscultatory method to verify the accuracy of
the SuperSTAT NIBP parameter. The auscultatory method (using the cuff and
stethoscope) determines the systolic and diastolic pressures from sounds that
occur during cuff deflation. Mean arterial pressure cannot be determined by the
auscultation method. The oscillometric method used with all DINAMAP
technologies determines systolic, mean and diastolic pressures from the
oscillation pattern that occurs in the cuff during deflation.
NOTE
Arrhythmias will increase the time required by the NIBP parameter to
determine a blood pressure.
DINAMAP Classic and auscultatory reference algorithm
The oscillometric method of determining NIBP is accomplished by a sensitive
transducer, which measures cuff pressure and minute pressure oscillations
within the cuff. The first determination sequence initially pumps up to a cuff
pressure of about 160 mmHg for adult/pediatric patients or 110 mmHg for
neonates depending on initial target pressure preset. After inflating the cuff, the
monitor begins to deflate it and measures systolic pressure, mean arterial
pressure, and diastolic pressure. When the diastolic pressure has been
determined, the monitor finishes deflating the cuff and updates the screen.
The monitor deflates the cuff one step each time it detects two pulsations of
relatively equal amplitude. The time between deflation steps depends on the
frequency of these matched pulses (pulse rate of the patient). However, if the
monitor is unable to find any pulse within several seconds, it will deflate to the
next step. The process of finding two matched pulses at each step provides
artifact rejection due to patient movement and greatly enhances the accuracy
of the monitor. The figure shows the NIBP determination sequence.
NIBP determination sequence (specific pressure values are examples only)
At each step the microprocessor stores cuff pressure, the matched pulse
amplitude, and the time between successive pulses. The stepped deflation and
matched pulse detection continues until diastolic pressure is determined or total
2048723-002D
CARESCAPE V100 Vital Signs Monitor
2-11
Equipment overview: Overall principles of operation
cuff pressure falls below 7 mmHg. The monitor then deflates the cuff (to zero
detected pressure), analyzes the stored data, and updates the screen.
The operating cycle is composed of four parts: inflation time, deflation time,
evaluation time, and wait time. Wait time, which varies from mode to mode, is
affected by the cycle time (auto mode) or operator intervention (manual mode).
The figure shows the basic operating cycle.
NIBP operating cycle
Systolic search
If systolic pressure is not found, the NIBP parameter can search at cuff pressures
higher than the initial target pressure. The parameter will inflate the cuff above
the initial target pressure to get more data in the systolic region. The pressure is
limited to the maximum allowed for the selected patient type.
In any operating mode, if a patient's systolic pressure exceeds the inflation
pressure of the monitor, the monitor will begin normal deflation sequence,
detect the absence of a systolic value, stop deflation, reinflate to a higher (than
initial) inflation pressure, and resume normal deflation sequence.
In manual mode, if a previous valid systolic pressure is displayed and less than 2
minutes old, and the new systolic pressure oscillations are compared with the
previous valid determination and the monitor "thinks" that the systolic was not
obtained, the monitor will inflate the cuff to a pressure above the immediately
preceding inflation.
Reference used to determine NIBP accuracy
To establish accuracy of an NIBP device, manufacturers have used several
different types of references. The reference blood pressures may be obtained by
invasive pressure monitoring at the central aortic region or at the radial sites.
The reference blood pressures may also be obtained by noninvasive methods
like auscultatory method (using cuff and stethoscope).
NOTE
For neonatal mode, the reference is always the intra-arterial pressure
monitoring method.
Monitors with intra-arterial reference (DINAMAP SuperSTAT and
classic technology)
For these monitors, the NIBP is referenced to the invasive blood pressure
obtained at the central aortic region.
2-12
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Equipment overview: Overall principles of operation
Monitors with auscultatory reference (DINAMAP auscultatory
reference technology)
In these monitors, the reference blood pressure is the auscultatory method for
adult and pediatric populations. For neonatal populations, the usual reference is
the invasive blood pressure obtained from the umbilical artery.
NOTE
For neonatal determinations the SuperSTAT algorithm is always used.
Temperature
The monitor uses the following technologies to measure patient temperature:
Alaris Turbo Temp, Alaris Tri-Site, or Exergen.
Alaris temperatures
The Alaris temperature probes contain a heating element that preheats the
probe to reduce determination time. The heating function is controlled by the
Main Board. The Alaris probes also contain a thermistor that indicates the
temperature. When the probe is attached to the temperature connector and
patient, the signal generated by a thermistor that senses temperature is routed
to the Main Board. When the probe makes contact with the patient, the
resistance of the thermistor is sensed by circuitry on the Main Board. The Main
Board then processes the digital signal and displays the patient temperature on
the UI Board and printer in Celsius or Fahrenheit.
When the monitor is powered on, the monitor automatically calibrates the
temperature circuit to account for ambient room temperature. This is done by
measuring a high precision resistor of known value, computing a calibration
factor, and applying this factor to all subsequent measurements.
NOTE
If large changes occur in the ambient temperature, the temperature system
can be recalibrated by cycling power using the On/Off button.
Furthermore, at one minute intervals, the monitor verifies the voltage supplied to
the temperature circuit to ensure that readings calculated using that factor are
accurate. If the voltage is found to be out of tolerance, the monitor issues an
alarm.
Alaris Turbo Temp or Tri-Site temperature options
NOTE
Either the Turbo Temp or the Tri-Site temperature option can be enabled on
the monitor at a time.
The Alaris temperature technology supports two temperature options: Turbo
Temp or Tri-Site. The Turbo Temp and Tri-Site temperature options allow the
clinician to take oral, rectal, or axillary temperature readings.
The Turbo Temp or Tri-Site temperature options support two different
temperature measurement modes of operation: fast (predictive) or continuous
(monitor).

2048723-002D
The Turbo Temp temperature option can take a fast (predictive) oral or rectal
CARESCAPE V100 Vital Signs Monitor
2-13
Equipment overview: Functional description
temperature measurement, but not a fast (predictive) axillary temperature
measurement.

The Tri-Site temperature option can take a fast (predictive) oral, rectal, or
axillary measurement.

Both the Turbo Temp and Tri-Site temperature options can take a
continuous (monitor) oral, rectal, or axillary measurement.
Exergen temperature
The Exergen TemporalScanner™ Temporal Artery Thermometer uses ultrafast
infrared scanning technology with arterial heat balance algorithms to quickly
and non-invasively measure the patient's temperature. As the caregiver passes
the scanner over the patient's skin, its infrared sensor samples at 1000 times per
second the radiant heat emanating from the body, which reaches a maximum
over the temporal artery. The scanner then derives the patient's body
temperature from the peak infrared sensor readings and the local ambient
temperature as measured by the scanner. A scan behind the ear is included in
the use protocol to prevent errors due to perspiration.
Refer to the operator's manual for complete instructions for use. For more
information on the theory of operation, scientific, educational and technical
information, access the following website: www.TAThermometry.org.
Functional description
The following paragraphs provide the functional interface relationship. The
monitor contains a number of electrical and electro-mechanical assemblies.
These assemblies are:

Main Board PWA

User Interface (UI) Board PWA

SpO2 PWA (optional)

Printer (optional)

Pneumatic Valve/Manifold (PVM)

Optical Switch (optional)
Main board PWA
The monitor’s Main Board is based on the NXP LPC2366 integrated
microprocessor. The microprocessor integrates Flash ROM, RAM, A/D converter
with input multiplexer, SPI interface, and timers into one chip. This
microprocessor is the primary processor for the monitor. It services and controls
the Patient Parameter Interface (PPI) devices, printer, UI Board, Real Time Clock,
audio circuit, and host communication. There are three TI MSP430 secondary
processors that control Power, NIBP and Temperature. The Power Processor
controls the watchdog, primary processor reset, and power supply control. The
Power processor is powered at all times.
The NIBP processor controls pneumatic safety interlock, timing check, and NIBP
control. The temperature processor controls the temperature parameter.
2-14
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Equipment overview: Functional description
Independent software in the primary and secondary processor periodically
communicates when the software systems are operating properly. When either
system stops processing or detects an error, it stops communicating with the
other. Either system, upon detecting a failure, can assert a safe state (herein
called FAILSAFE) of the hardware.
Upon entering a FAILSAFE condition, the Main Board will perform the following
tasks:

Parameter monitoring disabled

Alarm tone sounding from speaker

Pneumatic FAILSAFE (deflate the cuff, pump off)

Normal communications interface disabled

Remote alarm is in alarm state

Hard keys except On/Off key inactive
The On/Off key can reset the monitor and end the FAILSAFE condition. The
FAILSAFE condition will terminate automatically after 5 minutes to preserve
battery power.
All regulated DC power, isolated and non-isolated is generated on the Main
Board from main battery supply. The external DC input is used to charge the
main battery via charging circuitry on the Main Board.
User interface (UI) board PWA
The UI Board is used as a message center. It displays patient vital signs, alarms
status, monitor set-up, limit violation, NIBP cycle and the time the data was
received. The primary processor on the Main Board controls the UI Board. When
the primary processor reads the parameter signals, it decodes the signals and
routes the display information to the UI Board.
The UI assembly also provides hardkey switches for the monitor’s Main Board.
The primary processor asserts a HIGH on the 16 outputs of the 1-of-16 decoder/
demultiplexer one at a time and then reads at the signal on SW_MUX. A LOW on
SW_MUX indicates that the switch is asserted.
SpO2 PWA
The monitor can be configured for use with either an Ohmeda, Nellcor, or
Masimo SpO2 PWA. The SpO2 PWA provides continuous readings of oxygen
saturation and pulse rate. Additional circuitry on the Main Board provides power,
data communications, and isolation between SpO2 PWA and primary processor.
Patient data received from the finger sensor is filtered, amplified, and analyzed
on the SpO2 PWA. The information is sent to the Main Board via the optically
coupled electrically isolated serial connection. The primary processor receives
the data and routes it to the UI board for display. The data is also sent to the
printer if specified.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
2-15
Equipment overview: Functional description
Printer
The printer receives power from the Main Board and communicates with the
primary processor. Printer presence and print head temperature is indicated by
PR_TH signal to the primary processor. When a print command is sent to the
printer from the primary processor, the following will occur:

PR_CLK signal - transfer the data into print head

PR_DI signal - serial dot to be printed

PR_LAT signal - latch the data stream into the head

PR_ST1-6 - cause the head to print various sections

PR_M1-4 signals - control power sequentially to the two stepper motor
windings
Together these signals (CONTROL DATA) cause the printer to print a graphic
hardcopy of the patient vital sign values and trend data. It also causes the
printer to print a hardcopy of error logging and service record data.
The printer has a built-in sensor to monitor the printer paper presence. When the
printer is out of paper, it sends a PAPER OUT signal to the primary processor.
Pneumatics
The pneumatics consists of a pump, a deflate valve, and a dump valve. The
pneumatics inflates/deflates the cuff during NIBP determinations. During normal
operation the pneumatics are controlled by the primary processor. If a FAILSAFE
mode or overpressure condition occurs, the NIBP processor provides the
appropriate control signals to ensure a safe condition, where the cuff vents to
ambient atmosphere pressure.
Optical switch
The optical switch indicates whether the Alaris temperature probe is inserted in
the probe holder or not. The Main Board powers the switch.
2-16
CARESCAPE V100 Vital Signs Monitor
2048723-002D
2048723-002D
CARESCAPE V100 Vital Signs Monitor
Host Comm
Port (rear)
Temp Probe
(optional)
BP Cuff
SpO2 Probe
(optional)
Tubing
Control
Tubing
Control/Data
RS-232
Remote Alarm
Optical Switch
Temp Control/Data
Pump/Valve
Manifold
SpO2 Circuit
Unit Block Diagram
Speaker
Audio
Control
Temp Control
Interface
Printer
Control/Data
Printer
Driver
Isolated DC
Power Supply
PT1/PT2 NIBP
Data
Main Board
External DC
6V Battery
Display
LEDs
Switches
UI Board
Equipment overview: Functional description
2-17
Equipment overview: Functional description
For your notes
2-18
CARESCAPE V100 Vital Signs Monitor
2048723-002D
3
2048723-002D
Installation
CARESCAPE V100 Vital Signs Monitor
3-1
Installation: Unpacking and preparation for installation
Unpacking and preparation for installation
1.
Unpack and identify the contents of all shipping materials.
2.
Remove the monitor.
3.
Unpack the AC cord.
4.
Plug the AC cord into the AC Mains input on the external power supply, and
plug the supply DC output into the side of the monitor.
NOTE
Use only the original cord, a power cord recommended by GE, or a
regulatory-approved cord for the country of use.
5.
Plug the AC cord into a Hospital Grounded AC receptacle. The word
CHARGING will illuminate green on the front of the monitor indicating that
an AC source is available.
Prior to usage it is necessary to charge the monitor for 8 hours. This charge
calibrates the main battery charging circuitry with the charge status of the
battery.
Powering the monitor
Power sources
The monitor is designed to operate from an internal lead-acid main battery.
NOTE
The monitor is not designed to operate without a functional internal main
battery.
Main battery charging
Prior to each use, inspect the power supply cord to ensure proper connection
and condition.
NOTE
Repeated failure to fully recharge the battery will, over time, lead to a
significant reduction in the battery’s capacity.
With external DC power connected, the green CHARGING indicator will light to
indicate that the main battery is charging. This indicator remains active whether
the unit is on or off. An audible “two beep” sounds whenever the DC charger is
connected/disconnected.
When connected to the monitor, the battery charger sounds a single lowpitched tone followed by a single higher-pitched tone. Upon disconnection from
the monitor, the battery charger sounds a single high-pitched tone followed by a
single lower-pitched tone.
Battery charging will take place as long as the monitor remains connected to an
external DC power source.
3-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Installation: Powering the monitor

Charge battery pack for 8 hours before first use or after prolonged periods
of storage.

If the monitor is idle for extended periods, it should be fully charged at least
once a month to ensure optimum performance. If the monitor is to be stored
for longer than one month, first charge the battery and then remove it and
store it separately from the monitor.

The battery pack should be charged before use, because a charged battery
loses charge when left in storage. Sealed lead-acid batteries can discharge
to less than 80% of charge within 60 days of storage. Charging is done
automatically by the monitor when the external DC power is connected.

The battery pack should be charged at room temperature: 16°C to 30°C
(59°F to 86°F).

You can charge or top-off
the battery pack at any time.
You should not wait until
battery is fully discharged.

To prolong the life of the
battery, keep the monitor
connected to a DC power
supply whenever possible.
Do not allow the battery to
become completely
discharged.
Sys
to
lic
HIGH
MAP/
Cuff
LOW
Diast
olic
HIGH
LOW
Pulse
AUTO
HISTO
CYCL
E
RY
Rate
HIGH
LOW
SpO
HIGH
LOW
Tem
pera
ture
C
F

A fully charged battery will
power the monitor for
approximately 5-11 hours,
depending upon
configuration and usage.

To ensure full charge cycles, replace only with the specified battery.
BATTERY OK
When the monitor is operating on main battery power and the BATTERY LOW
alarm is not active, the BATTERY OK indicator is backlit green.
Battery alarms
When about 45 minutes of main battery charge remains:
The low-priority BATTERY LOW alarm is issued.
2048723-002D

The BATTERY LOW indicator illuminates.

This alarm can be acknowledged and cleared by pressing the Silence
button.

The BATTERY LOW alarm will re-alarm every 10 minutes after it has been
acknowledged.

If the alarm is not acknowledged, the alarm is re-issued every 8 seconds.

The monitor continues to operate normally.
CARESCAPE V100 Vital Signs Monitor
3-3
Installation: Powering the monitor
When about 5 minutes of main battery charge remains:
The low-priority BATTERY LOW alarm escalates to a high-priority BATTERY LOW
alarm.

The BATTERY LOW indicator flashes.

Any NIBP determination in progress at the time of the alarm escalation is
allowed to finish.

Any Stat mode cycle that was initiated before the alarm escalation is
allowed to finish.

The user is not able to initiate:

any new NIBP determinations of any type

any printouts
NOTE
At this time, it is highly recommended to plug the monitor into external DC
power.
When 5 minutes of main battery charge expires:
After 5 minutes of high-priority BATTERY LOW alarm, the monitor enters a
battery low shutdown.

No error code is displayed.

The BATTERY LOW indicator flashes.

The monitor alarms for 2.5 minutes, then shuts down completely.
NOTE
You must plug the monitor into DC power before resuming monitoring.
After plugging the monitor into DC power:

The BATTERY LOW indicator (when the monitor is on) and CHARGING
indicator illuminate.

The BATTERY LOW indicator turns off when the battery level reaches a
sufficient charge level to operate without the BATTERY LOW alarm active.
E13 BATTERY LOW
At any time while the high-priority BATTERY LOW alarm is active, certain actions
can trigger the ‘E13’ BATTERY LOW alarm: any attempt to start an NIBP
determination or a printout. This alarm is giving you additional warning that the
battery charge is critically low.
NOTE
At this time, it is highly recommended to plug the monitor into external DC
power.
3-4

The ‘E13’ error code appears in the min window.

The BATTERY LOW indicator flashes.

This alarm can be acknowledged by pressing the Silence button.

The user is not able to initiate:

any new NIBP determinations of any type

any printouts
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Installation: Configuring the monitor
Configuring the monitor
Operating modes
The monitor can operate in one of four modes: clinical, configuration, advanced
configuration, and service.
Clinical mode
Clinical mode is the monitor’s normal operating mode. While this mode is active,
alarm limits and a few other commonly used settings are adjustable. All
parameters are available for monitoring in this mode.
Configuration mode
Configuration and advanced configuration modes display the software revision
and allow you to configure defaults for some settings that are available in
clinical mode, as well as some less commonly used settings that are only
adjustable in these modes. A fatal error history is also available in the advanced
configuration mode. No parameters are operable in these modes, therefore,
patient monitoring is suspended.
Configuration mode settings
Monitor settings such as HIGH/LOW alarm settings changed in the Clinical Mode
will not be retained after the monitor is powered off. To retain alarm and
parameter settings, the changes must be done in the configuration mode. Date/
Time settings are also entered in the configuration mode.
To enter the configuration mode: with the monitor off, press and hold the Menu
button at the same time as pressing and holding the On/Off button for 3
seconds. The monitor enters the configuration mode.
For a few seconds immediately after power up in this mode, the Systolic and
Diastolic windows display the major and minor version codes. The version codes
are numbers that represent the letters of the English alphabet, which are
designated to the currently loaded version of the monitor firmware (e.g., 1
indicates A, 2 indicates B, etc.).
At the same time, the NIBP Algorithm selected in the monitor is displayed in the
min (minutes display) window as follows:

AUSC if the monitor is configured with auscultatory NIBP Algorithm

STAT if the monitor is configured with DINAMAP SuperSTAT Algorithm

CLAS if the monitor is configured with DINAMAP Classic Algorithm
Also, the Temperature probe selected in the monitor is displayed in the
Temperature window as follows:
2048723-002D

trb0 if the monitor is configured for Alaris Turbo Temp

trI if the monitor is configured for Alaris Tri-Site

tat if the monitor is configured for Exergen
CARESCAPE V100 Vital Signs Monitor
3-5
Installation: Configuring the monitor
Display
Window
Major software revision
Systolic
Minor software revision
Diastolic
Type of NIBP technology
min
Temperature type technology
Temperature
These displays appear only during the first part of the power up sequence and
are not selectable and cannot be changed. After a moment, this version
information is cleared, and the monitor displays the first page of configuration
mode which simply displays
in the Systolic window.
Pressing the Menu button cycles through all the configuration option pages.
After all options pages have been displayed, the display returns to the first
configuration mode page (displaying
). You can use the + and - buttons to
make changes to settings. After making changes, simply cycle the power to
return to normal operation (clinical) mode. Changes are automatically retained.
NOTES

If a parameter is not enabled, its options are not displayed.

Menu selections for SpO2 settings are different depending upon the SpO2
technology your monitor contains.
The Menu selections appear in the following order. Refer to the manual section
for settings options.
Setting
Window
LED display
Pulse Rate
window
display
Inflate pressure
(adult/ped)
Systolic
XXX (numeric)
XXX (numeric)
ADULT indicator illuminated,
INFLATE PRESSURE indicator
flashing
Inflate pressure
(neonate)
Systolic
XXX (numeric)
XXX (numeric)
NEONATE indicator illuminated,
INFLATE PRESSURE indicator
flashing
Line frequency mode
(Ohmeda TruSignal only)
SpO2
50 or 60
SpO2 mode
(Nellcor only)
SpO2
1 or 2
User selects the averaging
technique*
1=Normal Response
2= Fast Response
SpO2 sat
(Nellcor only)
SpO2
0, 10, 25, 50, 100
User selects the SMART Sat
tolerance level *
SpO2 mode
(Masimo only)
SpO2
4, 6, 8, 10, 12, 14, 16
User selects the number of
seconds over which data is
averaged 4 to 16*
3-6
CARESCAPE V100 Vital Signs Monitor
Comment
AC line frequency
2048723-002D
Installation: Configuring the monitor
Setting
Pulse Rate
window
display
Window
LED display
SpO2 sat
(Masimo only)
SpO2
0 or 1
Fast Sat Mode
0=Off
1=On*
SpO2 sensitivity
(Masimo only)
SpO2
1, 2, 3
1= Low Perfusion-Maximized,
2= Low Perfusion-Default,
3= for engaging Adaptive Probe
Off Technology algorithm*
Temperature units
Temperature
blank
C or F indicator illuminated (Alaris
only)
Temperature display
time
Temperature
2 or 5
User selects number of minutes
temperature values are
displayed.
Systolic
XXX (numeric)
use + and - keys to change
Month
MAP/Cuff
XXX (numeric)
use + and - keys to change
Day
Diastolic
XXX (numeric)
use + and - keys to change
Hour
min
XXX (numeric)
use + and - keys to change
Minute
min
XXX (numeric)
use + and - keys to change
Systolic
blank
Year
Mode
(when main screen is
active)
Comment
indicates configuration mode
NOTE: Refer to the “SpO2” section of operator’s manual for detailed descriptions of the different user selectable SpO2 settings.
Setting the date and time – To set the date and time on the monitor, you must
access the configuration mode. Press Menu to skip the default settings that do
not require changes. Refer to the table above.
NOTE
While in configuration mode, all entries stored in the clinical history are
erased when the time and/or date is changed.
Procedures
1.
Press the Menu button to move from one setting to another. Use the +/buttons to increment or decrement the setting.
NOTE
For the date and time to be saved, you must advance the menu through
the minute setting.
2048723-002D
2.
To exit the configuration mode, press the On/Off button.
3.
To continue with other changes, press the Menu button.
will appear in
the Systolic window. To change parameter settings, press the Menu button
CARESCAPE V100 Vital Signs Monitor
3-7
Installation: Configuring the monitor
and select the parameter function. To change alarm settings, press the
Alarms button.
Inflation pressure default setting
Procedures
1.
Enter the configuration mode: with the monitor off, press and hold the Menu
button at the same time as pressing and holding the On/Off button for 3
seconds.
2.
Use the +/- buttons to increment or decrement the inflate pressure default
setting.
3.
To exit the configuration mode, turn the unit off. To continue with additional
configuration settings, press Menu.
Vital sign alarm default settings
Procedures
1.
Enter the configuration mode: with the monitor off, press and hold the Menu
button at the same time as pressing and holding the On/Off button for 3
seconds. After the unit enters the configuration mode, press Alarms. At any
point in the configuration mode menu, Alarms default can be selected.
2.
To set or change the default setting, press the Alarms button to select alarm
setting. Use the +/- buttons to increment or decrement the individual
settings.
NOTE
For the Alarms default setting to be saved, you must advance the menu
through the SpO2 settings.
3.
To exit the configuration mode, turn the unit off. To continue with additional
configuration settings, press Menu.
Reverting to the factory default vital sign alarm limits
WARNING
The Line Frequency mode (for Datex-Ohmeda oximetry) must
be set according to each country’s electrical power utilities
implementation; and it must be checked and reset any time the
monitor is set to or reverts to factory default settings.
To revert to the factory default vital sign alarm limit settings, the monitor must
be disconnected from the DC power supply and from the monitor battery. Refer
to “Replacing the main battery on the monitor” on page 4-8 for DC power supply
and battery disconnection/reconnection instructions.
When reverting to factory default settings, the user settings (including alarm
limits and inflation pressure), date/time, and the Ohmeda TruSignal SpO2 Line
Frequency mode (LF) will go back to default values. Refer to “Configuration mode
settings” on page 3-5 to configure the factory default user settings.
3-8
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Installation: Configuring the monitor
NOTE
For monitors configured for Ohmeda TruSignal SpO2 only, verify that the
setting for Line Frequency mode (LF) is correct for your country. Refer to
“SpO2 configuration settings” on page 3-9.
SpO2 configuration settings
Procedure for units with Ohmeda TruSignal technology
1.
With the monitor off, press and hold the Menu button at the same time as
pressing the On/Off button until the display test completes.
2.
Press the Menu button until LF appears in the Pulse Rate window.
3.
Use the +/- buttons to select the option.
4.
To exit the configuration mode, turn the unit off. To continue with additional
configuration settings, press the Menu button.
WARNING
The Line Frequency (LF) mode must be set according to each
country’s electrical power utilities implementation. The LF
mode must be checked and reset any time the monitor is set to
or reverts to factory default settings.
If the LF mode is set incorrectly, the susceptibility to ambient
light is increased and low perfusion performance may be
affected, resulting in potentially inaccurate readings.
Procedure for units with Nellcor technology
1.
With the monitor off, press and hold the Menu button at the same time as
pressing the On/Off button until the display test completes.
2.
Press the Menu button until n0d (response mode) appears in the Pulse Rate
window.
3.
Use the +/- buttons to select the option.
4.
Press the Menu button once. SAt (SatSeconds) appears in the Pulse Rate
window.
5.
Use the +/- buttons to select the option.
6.
To exit the configuration mode, turn the unit off. To continue with additional
configuration settings, press the Menu button.
Procedure for units with Masimo technology
2048723-002D
1.
With the monitor off, press and hold the Menu button at the same time as
pressing the On/Off button until the display test completes.
2.
Press the Menu button until n0d (averaging time) appears in the Pulse Rate
window.
3.
Use the +/- buttons to select the option.
4.
Press the Menu button once. SAt (FastSAT) appears in the Pulse Rate window.
5.
Use the +/- buttons to select the option.
CARESCAPE V100 Vital Signs Monitor
3-9
Installation: Configuring the monitor
6.
Press the Menu button once. SEn (sensitivity mode) appears in the Pulse
Rate window.
7.
Use the +/-buttons to select the option.
8.
To exit the configuration mode, turn the unit off. To continue with additional
configuration settings, press the Menu button.
Temperature unit of measurement configuration settings
Procedure for units with Alaris probes
1.
With the monitor off, press and hold the Menu button at the same time as
pressing the On/Off button until the display test completes.
2.
Press the Menu button until Unt (unit of measurement) appears in the Pulse
Rate window.
3.
Use the +/- buttons to select the option.
4.
To exit the configuration mode, turn the unit off. To continue with additional
configuration settings, press the Menu button.
Procedure for units with Exergen scanner
The Exergen scanner comes preset with the requested unit of temperature
measurement, but can be changed. To change the scanner’s unit of
measurement (°C or °F):
1.
Unplug the scanner from the monitor’s host communication port.
2.
On the back of the scanner, loosen the single screw at the bottom and
remove the cover.
Cover
Single screw
3-10
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Installation: Configuring the monitor
3.
To set the unit of measurement to:

°F — move the switch up toward the probe cone

°C — move the switch away from the probe cone
°F
F/C switch
°C
4.
Replace the cover, and tighten the screw.
Temperature display time configuration settings
User selects number of minutes temperature values are displayed.
NOTE
This procedure applies to both the Alaris probe and the Exergen scanner.
1.
With the monitor off, press and hold the Menu button at the same time as
pressing the On/Off button until the display test completes.
2.
Press the Menu button until tdt (temperature display time) appears in the
Pulse Rate window.
3.
Use the +/- buttons to select the option.
4.
To exit the configuration mode, turn the unit off. To continue with additional
configuration settings, press the Menu button.
Advanced configuration mode
Advanced Configuration mode is entered by holding the Menu button and the button simultaneously while powering on with the On/Off button.
For a few seconds immediately after power up in this mode, the Systolic and
Diastolic display windows will display the major and minor version codes. The
version codes are numbers that represent the letters of the English alphabet
which are designated to the currently loaded version of the monitor firmware
(e.g., 1 indicates A, 2 indicates B, etc.).
After a moment, this version information is cleared, and the monitor displays the
first page of configuration mode which simply displays ACF in the Systolic
display window indicating that the monitor is in advanced configuration mode.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
3-11
Installation: Configuring the monitor
You can then press the Menu button to cycle through all the advanced
configuration mode option pages. After all options pages have been displayed,
the display will return to the first advanced configuration mode page (displaying
ACF). You can use the + and - buttons to make changes to settings. After making
changes, simply cycle the power to return to normal operation mode. Changes
are automatically be retained.
The advanced configuration mode option pages are as follows:
Displayed on monitor
Function
ACF
Advanced Configuration Mode announcement
(No settings are entered on this page.)
rEn
Remote mode
0 : Remote mode is disabled
1 : Remote mode is enabled (default)
Adr
Host communication unit address
32 : This is the default value: 126 max.
br
Host communication bit rate (bits per sec)
0 : 300 bps
1 : 600 bps
2 : 1200 bps
3 : 2400 bps
4 : 4800 bps
5 : 9600 bps (default)
6 : 19200 bps
NOTE
For the Exergen temperature to appear on
the monitor, the host communication bit rate
must be set to 9600 bps.
nod
Host communication mode
0 : Host communication command mode (default)
1 : 1846 Compatibility mode
(1846 mode requires user to also select 600 bps.)
Service mode
Service mode is entered by holding the Cycle button while powering on with the
On/Off button. You can press the Cycle button to advance through the available
service mode pages. You can use the + and - buttons to make changes to
settings.
NOTE
Only transducer calibration pages are available until calibration is valid.
Save settings
Calibration and other service mode setting changes will not be retained unless
the “Save Settings” operation is executed (on the final Service Mode options
page). To save settings in service mode, advance to the last page (page 6), then
press and hold the Menu button until the second of two tones sound.
3-12
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Installation: Configuring the monitor
NOTE
The first tone sounds as you first press the Menu button and the second
tone sounds after the monitor has saved the settings.
After all options pages have been displayed, the display will return to the first
service mode page (initial calibration page). The Service Mode option pages are
as follows:
Displayed on monitor
Function
0 (in min window)
Refer to calibration section for functions.
1 (in min window)
Refer to calibration section for functions.
2 (in min window)
Refer to calibration section for functions.
3 (in min window)
NIBP Algorithm Type loaded
(Displayed in MAP/Cuff display window)
1: DINAMAP Classic NIBP
2: DINAMAP Auscultatory NIBP
3: DINAMAP SuperSTAT NIBP
NOTE
Changing setting effects NIBP performance.
3 (in min window)
Alarm mode
(Displayed in Pulse Rate window)
0: IEC mode
1: Legacy mode
NOTE
4 (in min window)

Use the Alarms button to toggle between
the available options.

Refer to the “Alarms” section of the
operator’s manual for a detailed
description of the alarm modes.
SpO2 Type loaded
(Displayed in SpO2% display window)
0: No SpO2
1: Nellcor
2: Masimo
3: Ohmeda
NOTE
Incorrect setting will cause fatal 930 alarm
during operation.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
3-13
Installation: Configuring the monitor
Displayed on monitor
Function
5 (in min window)
Temperature loaded
(Displayed in Temperature display window)
0: No Temp
1: Alaris Turbo Temp
2: Alaris Tri-Site
3: Exergen
6 (in min window)
Language
The number displayed in Pulse Rate display
window indicates the language setting. These
range from 0 to 20. For example, 0 indicates
English. The language setting is used in printed
reports. Russian, Greek, Korean, and Japanese are
printed in English only.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
English
Not used
Czech
Danish
Dutch
Finnish
French
German
Greek
Hungarian
Italian
Japanese
Korean
Norwegian
Polish
Not used
Portuguese
Russian
Slovak
Spanish
Swedish
NOTE
You must be in option page 6 (in min window) to save any changes made in
service mode.
3-14
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Installation: Host communication connector
Host communication connector
CAUTION
Auxiliary equipment connected to the CARESCAPE V100 vital
signs monitor will result in the formation of an electromedical
system and thus, must comply with the requirements of IEC
60601-1-1. All host port signals are NON-ISOLATED and should
be connected to equipment conforming to IEC-60601-1 or
configured to comply with IEC 60601-1-1 only.
Where isolation of data communication is required, use one of the following:

ILC-1926 Isolated Line Converter (GE part number 001926) along with the
Host Comm Cable Assemblies (GE part numbers 683235 and 683242).

USB Cable Kit (GE part number 2040229-001).
If external alarm control is required, the Isolated Remote Alarm Cable (GE part
number 487208CR) should always be used.
When a high-priority alarm condition is displayed on the monitor, the remote
alarm signal becomes active within 0.5 seconds. The active state of the alarm
signal is an open circuit. In the inactive state the alarm signal is connected to
ground. Refer to the Information Sheet included with the Isolated Remote Alarm
Cable for operational details.
NOTE
When using the Isolated Remote Alarm Cable, the visual and audible alarms
of the monitor should still be considered the primary alarm delivery method.
The Remote Alarm connection should be considered a secondary method.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
3-15
Installation: Host communication connector
DB15 connector pin assignments
Connection details
Host port connector (rear panel)
Pin #
Function
1
Common
2
Inverted TTL Transmit Data
3
Inverted TTL Receive Data
4
+5 volts
5
No connection
6
No connection
7
Common
8
Remote Alarm
9
No connection
10
No connection
11
RS232 Transmit Data (TxD)
12
No connection
13
RS232 Receive Data (RxD)
14
No connection
15
No connection
Communication protocol
GE offers resources to assist customers in the development of software to
exchange data with the monitor, including the Host Communications Reference
Manual and the DINAWIN Application Programming Interface library. Contact
your GE sales representative for further information.
3-16
CARESCAPE V100 Vital Signs Monitor
2048723-002D
4
2048723-002D
Maintenance
CARESCAPE V100 Vital Signs Monitor
4-1
Maintenance: Preventative maintenance
Preventative maintenance
WARNING
Failure on the part of all responsible individual, hospital, or
institution using this equipment to implement a satisfactory
maintenance schedule may cause undue equipment failure
and possible health hazards.
WARNING
Calibration equipment should always be kept dry and free of
particulate matter. Moisture or foreign substances introduced
to the pneumatic system may cause damage to the monitor
and/or the accessories, leading to impaired performance and/
or inaccurate readings.
NOTE
GE does not, in any manner, assume the responsibility for performing the
recommended maintenance schedule, unless an Equipment Maintenance
Agreement exists. The sole responsibility rests with the individuals, hospitals,
or institutions utilizing the device.
Maintenance schedule
To ensure the monitor and its components remain in proper operational and
functional order, the following maintenance schedule is recommended:

Visual inspection: Prior to installation, every 12 months thereafter and each
time the equipment is serviced.

Parameter level functional testing: After the initial configuration is complete.

Calibration procedures and tests: Every 12 months, or whenever the
accuracy of any reading is in doubt.

Cleaning:

Monitors: Every 12 months or as usage demands.

Other components: As usage demands.
For details, see “Cleaning” on page 4-3.

Long term storage recommendations: every time the monitor is stored for
an extended period of time.

Electrical safety tests: Upon receipt of the equipment, every 12 months
thereafter, and each time the unit is serviced.
Integrity of hoses and cuffs
When the pneumatic integrity of any NIBP cuff and hose is in doubt, replace the
cuff and hose, and discard the questionable accessories.
4-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Visual inspection
Visual inspection
The monitor and its components should be carefully inspected prior to
installation, once every 12 months thereafter and each time the equipment is
serviced.
WARNING
Do not use damaged sensors, cables, or connectors.

Carefully inspect the equipment for physical damage to the case, the display
screen, and the keypad. Do not use the monitor if damage is determined.
Refer damaged equipment to qualified service personnel.

Inspect all external connections for loose connectors or frayed cables.

Have any damaged connectors or cables replaced by qualified service
personnel.

Inspect the display face for marks, scratches, or other damage.

Safety labels and inscription on the device are clearly legible.
Cleaning
Cleaning schedule
CAUTION
To prevent cross-contamination, clean the exterior surfaces of
the monitor, monitor accessories, and reusable sensors on a
regular basis in compliance with your institution’s infection
control unit and/or biomedical department’s local policy.
Cleaning the monitor, monitor accessories, and the Exergen temporal scanner
WARNING
Never pour or spray water or any cleaning solution on the
equipment or permit fluids to run behind switches, into
connectors, into the recorder, or into any ventilation openings
in the equipment. Do not let fluid “pool” around connection
pins.
WARNING
Use of unapproved cleaning agents can cause case damage
resulting in unintended fluid ingress and a potential for
compromising electrical safety.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
4-3
Maintenance: Cleaning
Cleaning the exterior surfaces of the monitor, monitor
accessories, or the Exergen temporal scanner
Disconnect the monitor from AC power before cleaning or disinfecting its
surface. The exterior surfaces of the monitor, monitor accessories, and temporal
scanner may be cleaned with a dampened, lint-free cloth. Wipe off all cleaning
solutions with a clean, dry cloth and let air dry for at least 15 minutes. Use one of
the following approved solutions:

Water

Mild soap

Household bleach (5.25% sodium hypochlorite). Mix 10:1 with distilled water.

Sagrotan (dilution 3:100, containing 75 mg tartaric acid per 100 ml solution).

Exergen temporal scanner only: Alcohol-based cleaning agents can be used
on the scanner’s probe head and metal neck only.
Never use the following cleaning agents on the monitor or the Exergen temporal
scanner:

Abrasive cleaners or solvents of any kind

Acetone

Ketone

Betadine

Alcohol-based cleaning agents. (However, an alcohol-based cleaning agent
can be used on the Exergen scanner’s probe head and metal neck only.)

Petroleum-based cleaning agents

Any type of solution that contains ammonium chloride, conductive
solutions, wax or wax compounds

Sodium salts
NOTE
Never autoclave or steam clean the monitor, cuffs, or accessories.
Cleaning the displays of the monitor or Exergen temporal
scanner
To clean the display covers, use a soft, clean cloth dampened with a glass
cleaner. Never spray the glass cleaner directly onto the display, and never use
alcohol- or petroleum-based products.
Cleaning the sensor lens of the Exergen temporal scanner
Dirt, greasy film, or moisture on the scanner lens will interfere with the accuracy
of the temperature reading. Regularly clean the lens with a cotton swab dipped
in alcohol and follow the instruction label on the scanner. Only use gentle
pressure for cleaning to avoid lens damage. Water can be used to remove any
residual film left by the alcohol. Do not use bleach or other cleaning solutions on
the sensor lens.
Cleaning the probe head and neck of the Exergen temporal
scanner
Use an alcohol-based cleaning agent on the Exergen scanner’s probe head and
metal neck only.
4-4
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Cleaning
Cleaning and disinfecting blood pressure cuffs
General
The cuff must be thoroughly cleaned with the specified detergent before reuse.
The additional use of household bleach as described below provides at least
intermediate-level disinfection.
NOTE
Never autoclave or steam clean the monitor, cuffs, or accessories.

Apply cuff hose caps before cleaning. See “NIBP accessories” on page 6-2
for the orderable part numbers of cuff hose caps.

While this procedure is adequate for cleaning/disinfection, it may not
remove all stains.

Do not immerse hoses.

Do not immerse cuffs without prior application of the cuff hose caps.
Materials

Enzymatic detergent such as ENZOL® enzymatic detergent (US) or
Cidezyme® enzymatic detergent (UK)

Distilled water

10% solution of household bleach (5.25% sodium hypochlorite) in distilled
water

Soft cloths and soft-bristled brushes

Spray bottles
Procedure
1.
Prepare the enzymatic detergent according to the manufacturer’s
instructions and the 10% bleach solution, in separate spray bottles.
2.
Spray the detergent liberally on the cuff. If the material is dried on, allow the
detergent to set for 1 minute. For soil on the soft part of the closure or the
cuff itself, wipe the material off with a soft cloth. For persistent
contamination on the soft part of the closure, use a soft-bristled brush to
loosen particles. Rinse with copious amounts of distilled water. Repeat until
no visible contamination remains. For soil on the hook part of the closure,
use a soft-bristled brush to remove the material, and rinse with copious
amounts of distilled water. Repeat until no visible contamination remains.
3.
Spray the 10% bleach solution on the affected area until the area is
saturated. Allow the solution to set for 5 minutes.
4.
Wipe away any excess solution and rinse the cuff again with distilled water.
Allow 2 hours for drying.
The user has the responsibility to validate any deviations from the
recommended method of cleaning and disinfection.
For additional information on infection control procedures, contact GE Technical
Support.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
4-5
Maintenance: Long-term storage
Cleaning the exterior surfaces of the Alaris temperature devices
It is good practice to periodically clean the probe’s surface by wiping it with a
soft cloth dampened with a mild detergent and warm water. Refer to the
Housekeeping, Central Service or Infection Control departments in your facility
for further information. You may use the following cleaning solutions:

Cidex®, Betadine®, or 3% hydrogen peroxide.
NOTE
Betadine may discolor the case. Use a 10% solution of bleach to remove the
discoloration. Apply the listed solutions with a dampened sponge, soft
brush, or a cloth, then wipe dry with a clean cloth or towel.
CareFusion Corporation does not recommend Ethylene Oxide (EtO)
sterilization of the Turbo Temp or Tri-Site temperature probes.
If you currently use a specific cleaning agent or disinfectant, we recommend
that you examine its chemical ingredients prior to use on the probe. If you
question the effect your specific cleaning agent or disinfectant has on your
instrument, contact your local GE Healthcare sales and service office or
distributor.
Do not use alcohol, ammonia, or ammonium chloride-based agents, as they could
damage the plastic exterior of the probe. Do not allow fluids to enter the probe.
Fluid leakage into the probe can cause damage. Do not autoclave or immerse
the probe, as damage will occur.
SpO2 sensors
Adhesive sensors are sterile and for single use only. For reusable temperature
sensors, consult the sensor manufacturer instructions for cleaning, sterilization,
or disinfecting methods.
Long-term storage
NOTE
When storing the product for extended periods, it is highly recommended to
disconnect the battery. Otherwise, the battery may over-discharge,
resulting in a significant reduction in battery life.
If it becomes necessary to store the monitor for an extended period of time,
remove all attached accessories. Attach the original packing inserts, and place
the monitor into the original shipping container.
Main battery life is significantly reduced if the battery is left in a discharged state.
For long-term storage, fully charge the battery, then remove the battery from
the unit and periodically charge the battery. For more information, refer to the
“Battery care” section below.
NOTE
When the monitor’s battery has been completely discharged, the monitor
must be connected to an external power supply before monitoring can
resume.
4-6
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Long-term storage
Long-term storage at high temperatures can lead to deterioration of seals and
separators and should be avoided.
Battery care
Main battery
WARNING
Keep the monitor connected to an external DC power source
when not in use to ensure maximum battery charge.
NOTE
The expected lifetime of the battery largely depends on the way in which the
monitor is used. If the battery is allowed to discharge to 50%, it should
survive approximately 400 charge/discharge cycles. Deeper discharge will
reduce battery life expectancy. It is never recommended to fully discharge
the battery.
If it becomes necessary to store the monitor for an extended period of time, first
fully charge, then remove the main battery. Then store the monitor and the main
battery in the original packaging materials.
Batteries should always be fully charged before being placed in storage. Even
after 6 months of storage, a fully charged battery can retain about 80% of its
charge. It is recommended that batteries should not be left in storage more than
6 months without a full recharge. A fully charged battery in good condition will
provide sufficient power to operate a monitor for approximately 5-11 hours,
depending upon configuration and use.

With the usage scenario of auto NIBP every 5 minutes with adult cuff,
printout after every determination, SpO2 parameter active at 60 bpm,
temperature parameter active in monitor mode, the average run time is 5
hours.

With the usage scenario of NIBP determinations every 15 minutes, without
SpO2 technology and temperature function active, the run time is up to 11.5
hours.
It is best to keep the battery charged as fully as practical and never store the
monitor with the battery in a discharged condition. When the battery will no
longer hold a charge, remove the battery and replace it with a GE-approved
battery. Failure to use a GE-approved battery may cause the monitor to shut
down. Refer to “Power accessories” on page 6-13 for the reorder part number.
NOTE
After replacing batteries, an ‘E00’ error code is normal. To clear the ‘E00’
error code, press the Silence button on the monitor. The user settings and
date/time revert to the factory default setting and all entries in clinical
history are erased.
For units with Ohmeda TruSignal technology, it is important to verify the Line
Frequency mode setting.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
4-7
Maintenance: Long-term storage
Battery charging will take place as long as the monitor remains connected to an
external DC power source.
Replacing the main battery on the monitor
DANGER
Before replacing the battery, disconnect the monitor from the
DC power supply.
NOTES

Record the configuration settings on your monitor before replacing the
battery. When the battery is replaced, all user settings are lost and return to
default values.

Replacement batteries can be obtained from GE.
1.
Unplug the monitor from the DC power source.
2.
Looking at the bottom of the monitor, remove the battery compartment
cover by removing the four screws that secure the cover and help card tray.
3.
Remove the help card tray and battery door cover.
WARNING
When reconnecting the battery, ensure the battery maintains
the correct polarity by connecting the red lead to the positive
terminal and the black lead to the negative terminal.
4-8
4.
Remove the old battery and disconnect the wires. Attach the battery wires
to the new battery, ensuring the red terminal (+) is connected to the red wire
and the black terminal (-) is connected to the black wire.
5.
When reconnecting battery power, the monitor enters fatal mode. To clear
the alarm, press the On/Off button.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Long-term storage
6.
Insert the battery into the compartment.
7.
Replace the cover, help card tray, and screws. Insert the external DC power
converter plug into the external DC power socket and plug into an AC outlet.
NOTES
 Error code ‘E00’ appears (MEMORY LOST) alerting you that the user
settings (including alarm limits and inflation pressure) and date/time will
go back to default values and all entries in clinical history are erased.
For units with Ohmeda TruSignal technology, it is important to verify the
Line Frequency mode setting.

Configured settings and time/date will not be lost when reset due to
pressing and holding the On/Off button regardless of whether the DC
charger is attached.
8.
Reset the date/time and applicable user settings.
9.
Verify the configuration settings prior to returning the monitor to clinical use.
Exergen temporal scanner battery
NOTE
If the Exergen scanner is not used regularly, remove the battery to prevent
possible damage due to chemical leakage.
Replacing the Exergen temporal scanner battery
1.
2048723-002D
Disconnect the scanner cable from the monitor.
a.
Loosen the two thumbscrews from the scanner’s modular plug.
b.
Unplug the scanner cable from the monitor’s host communication port.
CARESCAPE V100 Vital Signs Monitor
4-9
Maintenance: Long-term storage
2.
Loosen the single screw at the bottom, on the back of the scanner, and
remove the battery cover.
Cover
9-volt battery
Single screw
3.
Disconnect the old battery and replace with a new, high quality 9-volt
alkaline battery in the same location.
4.
Replace the battery cover, and tighten the screw.
5.
Reconnect the scanner cable to the host communication port, and tighten
the two thumbscrews.
Fuses
The monitor contains three fuses. The fuses are mounted within the monitor. The
fuses protect the low voltage DC input, the main battery, and the remote alarm
output. The +5 V output on the host port connector is regulated by internal
supply. Fuses are not replaceable.
4-10
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Parameter level functional testing
Parameter level functional testing
Use the accessories supplied with the monitor to perform functional testing of
each of the parameters after the initial configuration is complete.
Refer to the operator’s manual for more detailed parameter-specific
instructions.
NIBP
1.
Perform an NIBP determination on yourself.
a.
Connect the supplied air hose and cuff together.
b.
Connect the end of the air hose to the NIBP connector on the front of
the monitor.
c.
Attach the adult cuff to the upper part of your arm.
NOTE
If you are uncertain as to the proper technique, consult the
operator’s manual.
d.
2.
Press Inflate/Stop button on monitor to begin a determination.
Verify that a blood pressure determination completes and the results are
displayed on the monitor.
NOTE
While an NIBP simulator device may be useful to verify that the monitor
responds to oscillometric pulsations, it should not be used as a basis for
assessing the accuracy of measurement. For more information, see
“Appropriate use of NIBP simulators” on page B-2.
Temperature
Alaris
NOTES

Predictive temperature measurements cannot be performed when a
resistor is used in place of the probe.
2048723-002D

The accuracy of predictive temperature measurements made in a water
bath will not be representative of performance with actual patients.
1.
Connect the supplied Alaris temperature probe to the corresponding
connection.
2.
Take an oral or axillary temperature reading on yourself (i.e., not on a
resistor simulator).
3.
Verify that a predictive temperature begins once the probe is removed from
its holster.
4.
Place the probe in the holster after completion of the Temp cycle.
CARESCAPE V100 Vital Signs Monitor
4-11
Maintenance: Parameter level functional testing
Exergen
1.
Connect the Exergen temporal scanner’s modular plug to the host
communication port at the back of the monitor.
2.
Take a temperature reading of yourself (i.e., not on a resistor simulator).
3.
Verify that the temperature displays both on the Exergen temporal scanner
and in the Temperature window on the monitor.
Ohmeda, Nellcor, and Masimo SpO2 technologies
The SpO2 sensor is an assembly consisting of two parts: the sensor and the
extender cable.
4-12
1.
Connect the cables prior to attaching to the monitor.
2.
Verify that an SpO2 reading is displayed within moments of attaching the
sensor to either a simulator or to your finger.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Calibration procedures and tests
Calibration procedures and tests
Perform the following calibration test procedures every 12 months, or whenever
the accuracy of any reading is in doubt.
NOTE
All devices are tested and calibrated during manufacturing and are certified
for operation at installation.
To adequately test the safety and integrity of the monitor, the following test
equipment is recommended:

12VDC power supply

IEC 60601-1 safety tester

Digital manometer (with range to 350 mmHg)

Stopwatch/timer (capable of measuring seconds)

Adult NIBP cuff, Neonate NIBP cuff, hose, inflation bulb, and associated
tubing

Calibration kit (p/n 320246, available through GE)

SpO2 cable (for appropriate SpO2 type, if SpO2 is installed)

TE 1811 Temperature Probe Simulator (if TEMP is installed) available from
CareFusion Corporation.

Exergen Calibration Verification Kit (if Exergen option is installed) (p/n
EX129003)

Printer paper (if printer is installed)

3” diameter rigid cylinder (mandrel)

SpO2 connector with all leads shorted

Temperature connector with all leads shorted

DC input connector with both wires shorted
WARNING
Calibration equipment should always be kept dry and free of
particulate matter. Moisture or foreign substances introduced
to the pneumatic system will likely cause damage to the
monitor and/or the accessories.
Parameter test procedures
Complete the “Test results form” on page 4-29 as tests are performed.
NOTES
This test is written so that a knowledgeable technician who is familiar with
the monitor and the test equipment will be able to follow the test procedure.


2048723-002D
To enter Service Mode press and hold Cycle button while pressing the On/
Off button.
CARESCAPE V100 Vital Signs Monitor
4-13
Maintenance: Calibration procedures and tests
Setup
1.
Connect manometer to unit as shown.
2.
‘T’ an inflation bulb into the pneumatic setup.
3.
Consult the following diagram for pneumatic setup guidelines.
NIBP tests
Pneumatic leakage testing
NOTE
To enter Service Mode press and hold the Cycle button while pressing the
On/Off button.
4-14
1.
Turn unit on and enter Service Mode.
2.
Press Cycle button and 1 should appear in the min window.
3.
Close the valve on the inflation bulb.
4.
Using the inflation bulb, inflate the system to 210 mmHg.
5.
Allow the system to stabilize for 5 seconds (it is normal to see some
decrease in pressure at this point).
6.
Start the stopwatch and record the pressure value.
7.
After 60 seconds record the pressure value.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Calibration procedures and tests
The leakage rate is the difference between the first and second readings.
8.
Record and verify the leakage rate on the “Test results form” on page 4-29.
9.
Turn the monitor off.
Pressure transducer verification
NOTE
To enter Service Mode press and hold the Cycle button while pressing the
On/Off button.
1.
Turn unit on and enter Service Mode.
2.
The min window should display 0.
3.
Open the valve on the inflation bulb and remove all pressure from the
system (manometer reads zero).
4.
Press Cycle button and 1 should appear in the min window.
5.
Use the inflation bulb to inflate the cuff, hose and pressure indicator setup to
200 mmHg.
6.
Record and verify the pressure reading that appears in the Systolic window.
7.
Record and verify the pressure reading that appears in the Diastolic
window.
8.
Use the valve on the bulb to reduce pressure to 150 mmHg.
9.
Record and verify the pressure reading that appears in the Systolic window.
10. Record and verify the pressure reading that appears in the Diastolic
window.
11. Use the valve on the bulb to reduce pressure to 100 mmHg.
12. Record and verify the pressure reading that appears in the Systolic window.
13. Record and verify the pressure reading that appears in the Diastolic window.
14. Use the valve on the bulb to reduce pressure to 50 mmHg.
15. Record and verify the pressure reading that appears in the Systolic window.
16. Record and verify the pressure reading that appears in the Diastolic
window.
17. Confirm all test results are recorded on the “Test results form” on page 4-29.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
4-15
Maintenance: Calibration procedures and tests
Pressure transducer calibration
Perform only if Pressure Transducer Verification is out of tolerance as specified in
the “Test results form” on page 4-29.
NOTE
To enter service mode press and hold Cycle button while pressing the On/
Off button.
1.
Turn the monitor on and enter Service Mode.
2.
The min window should display 0.
3.
Open valve on bulb to open pressure system to atmosphere.
4.
Verify the manometer reads zero.
5.
Press Cycle button and 1 should appear in the min window.
6.
Close valve on bulb and slowly inflate pressure to 200 mmHg (using the
manometer as reference).
7.
Press Menu button when pressure reads exactly 200 mmHg to set
calibration value.
8.
To save the calibration setting, press the Cycle button until 6 appears in the
min window.
9.
Press and hold Menu button until monitor beeps and the number in the
MAP/Cuff window decrements by 1, which acknowledges that data was
saved.
10. Turn the monitor off.
Overpressure verification
NOTE
To enter service mode press and hold Cycle button while pressing the On/
Off button.
4-16
1.
Wait a few seconds after entering service mode. Press Cycle button so that
the min window changes from 0 to 1.
2.
Use the inflation bulb to inflate close to 300 mmHg. Slowly inflate (1 to 2
mmHg/sec) until valve opens and pressure is released.
3.
Record and verify pressure at which valve opens on the “Test results form”
on page 4-29.
4.
Press Cycle button and 2 should appear in the min window.
5.
Use the inflation bulb to inflate close to 150 mmHg. Slowly inflate (1 to 2
mmHg/sec) until valve opens and pressure is released.
6.
Record and verify pressure at which valve opens on the “Test results form”
on page 4-29.
7.
Turn unit off.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Calibration procedures and tests
Button testing
1.
Disconnect the cuff/hose assembly and power on the unit.
2.
Press Inflate/Stop button.
3.
Verify a NIBP determination has been initiated.
4.
Block pump port and verify ‘E80’ alarm.
5.
Press Silence button, verify alarm has been cleared.
6.
Verify that the alarm silence indicator (bell) is lit.
7.
Press Alarm button several times, verify unit cycles through all alarm
settings (i.e., SYS, DIA, SpO2).
8.
Confirm all test results are recorded on the “Test results form” on page 4-29.
9.
Turn unit off.
NIBP functional test
NOTES

The NIBP function test does not test for measurement accuracy.

While an NIBP simulator device may be useful to verify that the monitor
responds to oscillometric pulsations, it should not be used as a basis for
assessing the accuracy of measurement. For more information, see
“Appropriate use of NIBP simulators” on page B-2.
1.
Remove the calibration setup and attach an adult cuff and hose to a
simulator (be sure to select the correct cuff size).
2.
Press Inflate/Stop button on monitor to begin a determination.
3.
Record Systolic, Diastolic, MAP and heart rate from the monitor display.
4.
Wait 1 minute, then press Cycle button to initiate a determination in Auto
NIBP mode.
5.
Record Systolic, Diastolic, MAP and heart rate from the monitor display.
6.
Wait 1 minute, then press Cycle button until stat is displayed in the min
window to initiate a determination in STAT mode.
7.
Record Systolic, Diastolic, MAP and heart rate from the monitor display.
8.
Press Inflate/Stop button, end STAT mode.
9.
Confirm all test results are recorded on the “Test results form” on page 4-29.
NIBP overpressure verification
2048723-002D
1.
Remove the cuff/hose from the monitor, restrict airflow from cuff hose port.
2.
Press Inflate/Stop to begin NIBP determination.
3.
Verify ‘E80’ is displayed on the Systolic window and audible alarm sounds.
4.
Remove the air restriction.
5.
Press Inflate/Stop and verify that the pump does not start.
6.
Press the Silence button.
CARESCAPE V100 Vital Signs Monitor
4-17
Maintenance: Calibration procedures and tests
7.
Press the Silence button again.
8.
Verify the alarm condition is cleared from the Systolic window.
9.
Confirm all test results are recorded on the “Test results form” on page 4-29.
1.
Power on the monitor.
2.
During the power-up self-test verify all 7 segment LEDs and all discrete LEDs
illuminate and they are the correct color.
LED tests
NOTE
In the following figure, the items with a solid border are segment LEDs,
and the items with a dotted border are discrete LEDs.
Segment LED
Discrete LEDs
3.
Repeat power up cycle until all LEDs are checked.
4.
Confirm all test results are recorded on the “Test results form” on page 4-29.
1.
Plug the power supply into the monitor.
2.
Verify that the CHARGING indicator is illuminated.
3.
Confirm all test results are recorded on the “Test results form” on page 4-29.
External DC verification
Temperature (perform if equipped with Temp module)
At installation, GE recommends performing a temperature check. Refer to
“Parameter level functional testing” - “Temperature” on page 4-11.
4-18
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Calibration procedures and tests
Alaris temperature calibration verification
NOTES

There are no user-performed maintenance or calibration procedures for
Alaris thermometry.

To verify the accuracy of the Alaris temperature parameter with a specific
temperature probe, take measurements at varying temperatures in
continuous (monitor) mode using a water bath and a high-precision
thermometer as a reference instrument.
1.
Turn the monitor off. Make sure the temperature probe is properly stored in the
probe well.
2.
Disconnect the temperature probe cable from the monitor.
3.
Connect Temp simulator; set to 80.2°F.
4.
Turn the monitor on.
5.
If your measurement units are set to °C, switch the measurement units to °F.
Refer to “Temperature unit of measurement configuration settings” on
page 3-10 for instructions.
6.
Put the monitor into temperature monitor mode:
a.
b.
c.
Remove the probe from the well.
Press the + key.
Verify that a blinking temperature appears quickly. If not, return the
probe to the holder and repeat steps 6a and 6b.
7.
Record and verify the reading in the temperature display is 80.2°F ±0.2°F.
8.
Set the simulator to 98.6°F.
9.
Record and verify the reading in the temperature display is 98.6°F ±0.2°F.
10. Set the simulator to 107.8°F.
11. Record and verify the reading in the temperature display is 107.8°F ±0.2°F.
12. If necessary, switch the measurement units to °C. Refer to “Temperature unit
of measurement configuration settings” on page 3-10 for instructions.
13. Confirm all test results are recorded on the “Test results form” on page 4-29.
14. Calibration is complete. If the monitor does not pass the calibration
verification, contact GE Technical Support.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
4-19
Maintenance: Calibration procedures and tests
Alaris temperature probe date of manufacture
If required for your maintenance procedures, the Alaris temperature probe’s
date of manufacture is stamped into the probe’s RJ45 connector. The first two
digits equal the year of manufacture, the second two digits equal the week of
manufacture. In the example below, 0835 equals fiscal week 35 in the year of
2008.
Year
Week
Exergen temperature calibration verification
The Exergen temporal scanner is self-calibrating. Factory calibration data is
installed via a computer that communicates with the temporal scanner’s
microprocessor. The instrument uses this data to self-calibrate automatically
each time it is turned on, and will never require recalibration. If readings are not
correct, the instrument should be returned for repair.
NOTE
If calibration is needed, return the unit to the manufacturer.
Calibration verification kit
The calibration verification procedure requires the Exergen Calibration
Verification Kit (p/n EX129003). The calibration verification kit includes a portable
blackbody heat generator providing a stable source of heat in a small cavity.
This is used as a target reference to verify the calibration of the Exergen
temporal scanner against an Exergen Certified Master (CM) reference
instrument, also included in the kit.
Calibration verification procedure
The CM instrument must be the same model and calibration as the units to be
tested (S/N labels on the instruments indicate if device is Oral or Arterial and F or
C). If this is not the case, contact GE Technical Support.
NOTE
Comparisons between the CM and the instrument being tested should
always be conducted under the same conditions.
4-20
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Calibration procedures and tests
1.
Turn on the verifier device, using either a 9-volt battery or the power supply.
Make sure the red LED is illuminated.
Power On LED
On/Off switch
Battery
compartment
Power supply
jack
2.
Allow device approximately 5 minutes for warm-up and stabilization time.
3.
Allow certified master and the instrument to be tested to acclimate in the
same ambient temperature for at least 10 minutes.
4.
For all instruments, make sure the lens at the tip of the probe is clean. To
clean, use an alcohol prep or a swab dipped in alcohol, followed by a damp
wipe with water to remove any residue.
5.
Alternately insert the reference instrument and the instrument being verified
into the aperture opening, comparing the readings.
Certified master (CM) or
instrument to be verified
Portable black
body verifier
6.
Record and verify the difference between the temperature reading of the
CM and the instrument being verified is ±0.2°C (0.4°F).
If the readings differ by more than the acceptable field limits, repeat this
procedure. If the readings still differ by more than the acceptable limits, the
device fails.
7.
Confirm test results are recorded on the “Test results form” on page 4-29.
SpO2 (perform only if equipped with SpO2 module)
2048723-002D
1.
Connect the appropriate SpO2 probe and cable to the SpO2 connector. Place
the probe on your finger.
2.
Verify the unit displays a:

Pulse value

Saturation value

Signal Strength Bar Graph
CARESCAPE V100 Vital Signs Monitor
4-21
Maintenance: Calibration procedures and tests
3.
Remove the sensor from your finger to generate a ‘---’ (SpO2 SENSOR OFF
FINGER) alarm and to sound the speaker.
4.
Press the Silence button.
5.
Verify the sound has stopped and the ‘---’ (SpO2 SENSOR OFF FINGER) error
is cleared.
6.
Re-apply the SpO2 sensor to your finger.
7.
Verify the unit displays a:

Pulse value

Saturation value

Signal Strength Bar Graph
8.
Confirm all test results are recorded on the “Test results form” on page 4-29.
1.
Load paper into the print mechanism.
Printer output test
NOTE
Use only printer paper from GE.
4-22
a.
With the monitor powered on, turn it so that the side with the printer is
facing you.
b.
While grasping the side of the monitor, lift the printer door open by
placing your thumb in the indented area and pulling. The printer door
will pop open.
c.
Place the roll of paper into the compartment so that the end of the
paper comes off the right-side of the roll (paper is wound around the roll
clockwise). Place the roll of paper in the holding bracket that is
integrated in the door of the printer, making sure the paper extends out
of the printer cavity at least two inches.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Safety testing
2.
Firmly press the door to close it.
3.
Press Print button.
4.
Verify the printer outputs a record and print quality is good.
5.
Confirm test results are recorded on the “Test results form” on page 4-29.
Safety testing
Electrical safety tests
Electrical safety tests provide a method of determining if potential electrical
health hazards to the patient or operator of the device exist.
Recommendations
Qualified personnel must perform all safety tests presented in this document:
2048723-002D

Upon receipt of the monitor and its associated equipment).

Every 12 months thereafter (Planned/Preventive Maintenance). Refer to the
“Maintenance schedule” on page 4-2 for more information.

Each time the main enclosure is disassembled or a circuit board is removed,
tested, repaired, or replaced (Corrective Maintenance).

GE recommends that the qualified personnel performing the tests should
record the values of each required electrical safety test in the “Test results
form” on page 4-29. These instructions are intended for any component in
the system requiring electrical safety testing.
CARESCAPE V100 Vital Signs Monitor
4-23
Maintenance: Safety testing
Test equipment
The recommended test equipment required to perform electrical safety tests is
listed below.
Item
Specification
Leakage Current Tester
Equivalent to the circuits shown
Digital Multimeter (DMM) (optional,
based upon leakage tester and location)
AC volts, ohms
SpO2 Test Body
2006036-001
Safety Testing Cable Kit
2026107-006
NOTE
This kit contains the Temperature
Test Body.
Perform electrical safety tests using an electrical safety analyzer per IEC 606011, UL 60601-1, or CSA C22.2 No. 601. The schematics in the section provide a
general understanding of the test equipment. Actual configuration of test
equipment may vary.
The monitor being tested should be placed on an insulating surface.
Power outlet test
Verify that the power outlet is wired correctly per the country’s electrical code
standard before starting the following electrical safety tests. The results of the
following tests will be inaccurate unless a properly wired power outlet is used.
Use only non-isolated power outlets when performing safety tests.
Power cord and plug
Verify the power cord being used with the patient monitor is good. The following
are several areas to check for in this regard:

Failure of the power cord strain relief is very common. Often times users of
the equipment pull on the power cord itself, rather than the power cord plug,
to unplug the patient monitor from a wall receptacle.

Inspect the power cord for wear or damage regularly. If damage is
suspected, test for continuity through each conductor of the power cord
connector.

Verify line, neutral, and earth conductors are properly connected to the
power cord plug and are not short-circuited. Replace the power cord, as
necessary, with a regulatory-approved cord for the country of use.
WARNING
Use only AC power cords recommended or manufactured by
GE.
4-24
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Safety testing
Patient leakage current test
This procedure measures the leakage current from the “Device Under Test” input
connector to ground.
Perform tests in both Normal Condition (NC) and in Single Fault Condition (SFC),
where one of the supply conductors is open at a time. Perform the test with
normal and reverse polarity.
NOTE
*The MD represents the network and voltage measuring instrument and its
frequency characteristics per IEC 60601-1.
The patient connector test body shorts all signals in the connector together.
Refer to the instructions contained with the safety analyzer to perform this test.
NOTES

Perform this test once for SpO2 and once for Temperature.
2048723-002D

This test applies only to the Alaris temperature option; it is not intended for
the Exergen temperature option.
1.
Connect the appropriate Test Body to the input connector of the device
under test.
2.
Configure leakage tester as follows:

Polarity – NORMAL

Neutral – CLOSED

GND (Earth) – CLOSED
3.
Apply the AC mains voltage to the device under test.
4.
Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
5.
Change leakage tester switches to:

Polarity – NORMAL

Neutral – OPEN

GND (Earth) – CLOSED
CARESCAPE V100 Vital Signs Monitor
4-25
Maintenance: Safety testing
6.
Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
7.
Change leakage tester switches to:

Polarity – NORMAL

Neutral – CLOSED

GND (Earth) – OPEN
8.
Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
9.
Change leakage tester switches to:

Polarity – REVERSED

Neutral – CLOSED

GND (Earth) – OPEN
10. Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
11. Change leakage tester switches to:

Polarity – REVERSED

Neutral – OPEN

GND (Earth) – CLOSED
12. Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
13. Change leakage tester switches to:

Polarity – REVERSED

Neutral – CLOSED

GND (Earth) – CLOSED
14. Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
15. Remove the AC mains voltage from the device under test.
16. Repeat the steps in this procedure using the appropriate Test Body for any
additional devices requiring safety testing.
If measured reading is greater than the acceptance criteria below, the device
under test fails. Contact GE Technical Support.
Acceptance criteria NC
All readings must be less than or equal to 100 µA.
Acceptance criteria SFC – ground (earth), line or neutral open
All readings must be less than or equal to 500 µA.
4-26
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Safety testing
Patient leakage current test (mains voltage on the applied part)
This procedure measures the leakage current from a mains voltage source into
the “Device Under Test” input connector.
The patient connector test body shorts all signals in the connector together.
Refer to the instructions contained with the safety analyzer to perform this test.
Connect the appropriate Test Body to the input connector of the device under
test.
Perform the test with normal and reverse polarity.
AC MAINS
Leakage Tester
LINE
NORM
Power Cord
NEUTRAL
LINE
NEUTRAL
EARTH
EARTH
RVS
**
Closed
Patient connector
Test Body
MD*
Device
Under
Test
(Keep cable length as
short as possible.)
NOTE
*The MD represents the network and voltage measuring instrument and its
frequency characteristics per IEC 60601-1.
**Per IEC 60601-1, the resistance to protect the circuitry and the person
performing the test. The resistance must be low enough to accept currents
higher than the allowable values of the leakage current to be measured.
WARNING
Shock hazard. The following step causes high voltage at the
test body. Do not touch the test body.
NOTE
Perform this test once for SpO2 and once for Temperature.
1.
2048723-002D
Configure leakage tester as follows:

Polarity – NORMAL

Neutral – CLOSED

GND (Earth) – CLOSED
2.
Apply the AC mains voltage to the device under test.
3.
Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
CARESCAPE V100 Vital Signs Monitor
4-27
Maintenance: Safety testing
4.
Change leakage tester switches to:

Polarity – REVERSED

Neutral – CLOSED

GND (Earth) – CLOSED
5.
Read the current leakage indicated on the tester and record the results on
the “Test results form” on page 4-29.
6.
Remove the AC mains voltage from the device under test.
7.
Repeat the steps in this procedure using the appropriate Test Body for any
additional patient connectors requiring safety testing.
If measured reading is greater than the acceptance criteria below, the device
under test fails. Contact GE Technical Support.
Acceptance criteria
All readings must be less than or equal to 5 mA.
4-28
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Test results form
Test results form
Description
Min
Max
0
6
Pressure reading at 200mmHg, top display - Systolic
197
203
Pressure reading at 200mmHg, bottom display Diastolic
197
203
Pressure reading at 150mmHg, top display - Systolic
147
153
Pressure reading at 150mmHg, bottom display Diastolic
147
153
Pressure reading at 100mmHg, top display - Systolic
97
103
Pressure reading at 100mmHg, bottom display Diastolic
97
103
Pressure reading at 50mmHg, top display - Systolic
47
53
Pressure reading at 50mmHg, bottom display Diastolic
47
53
Overpressure threshold, Adult (mmHg)
305
325
Overpressure threshold, Neonate (mmHg)
150
165
Actual
Pass-Fail-N/A
NIBP Tests
 Pneumatic leakage result (mmHg)
 Pressure transducer verification
 Overpressure verification
 Buttons
NIBP Determination Initiated
‘E80’ displayed on Systolic display
Audible alarm can be silenced
Alarm silence indicator (bell) is lit
Overpressure alarm can be cleared
Alarm button is functioning
 NIBP determination
Systolic reading (mmHg)
Diastolic reading (mmHg)
MAP reading (mmHg)
Heart rate reading (bpm)
Systolic reading (mmHg)
Diastolic reading (mmHg)
MAP reading (mmHg)
Heart rate reading (bpm)
Systolic reading (mmHg)
Diastolic reading (mmHg)
MAP reading (mmHg)
2048723-002D
CARESCAPE V100 Vital Signs Monitor
4-29
Maintenance: Test results form
Description
Min
Max
Temperature reading at 80.2° F
79.9° F
80.5° F
Temperature reading at 98.6° F
98.4° F
98.8° F
Temperature reading at 107.8° F
107.5° F
108.1° F
Actual
Pass-Fail-N/A
Heart rate reading (bpm)
 NIBP overpressure
‘E80’ displayed on Systolic display
Pump will not start
Overpressure alarm can be cleared
Display
All 7-Segment LEDs Light Correct Color
All Discrete LEDs Light, Correct Color
External DC detection
CHARGING indicator LED illuminated
Temperature test
 Alaris
 Exergen
Temperature reading of reference instrument
Temperature reading of instrument being verified
Difference between temperature reading of reference
instrument and instrument being verified
±0.2° C
(0.4° F)
SpO2
Pulse Value Displayed
Saturation Value Displayed
Signal Strength Bar
‘---’ displayed on SpO2 display
Alarm is silenced, error display remains
Pulse Value
Saturation Value Displayed
Signal Strength Bar
Printer test
Printout is generated cleanly
Safety testing
 Patient leakage
4-30
Fwd Pol, Neut Clsd, Gnd Clsd
100µA
Fwd Pol, Neut Open, Gnd Clsd
500µA
Fwd Pol, Neut Clsd, Gnd Open
500µA
Rev Pol, Neut Clsd, Gnd Open
500µA
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Maintenance: Test results form
Description
Min
Max
Rev Pol, Neut Open, Gnd Clsd
500µA
Rev Pol, Neut Clsd, Gnd Clsd
100µA
Actual
Pass-Fail-N/A
 Patient leakage current (mains on applied part)
2048723-002D
Fwd Pol, Neut Clsd, Gnd Clsd
5mA
Rev Pol, Neut Clsd, Gnd Clsd
5mA
CARESCAPE V100 Vital Signs Monitor
4-31
Maintenance: Test results form
4-32
CARESCAPE V100 Vital Signs Monitor
2048723-002D
5
2048723-002D
Troubleshooting
CARESCAPE V100 Vital Signs Monitor
5-1
Troubleshooting: Overview
Overview
The symptoms and solutions in this chapter represent only a few of the
problems that you may encounter and are not intended to cover every possible
problem that may occur.
A systematic approach to the diagnosis of problems as well as a general
understanding of the architecture, both hardware and software, of the monitor
are essential to ensure successful troubleshooting of a device. GE recommends
formal service training before repairs are attempted. These troubleshooting
procedures combined with training provide the service technician with skills
necessary to service and repair a monitor in the event of a malfunction.
Problems
Before starting any detailed troubleshooting, complete a thorough visual
inspection of the following.
Problem
Exergen temperature does not
appear on the monitor
5-2

All cable connections secure?

Devices properly powered?

Connected to a proper power source?
Possible reason
Solution
The host communication bit rate
may be set incorrectly.
Confirm that the host
communication bit rate (br) is set at
the default setting (9600). Refer to
“Advanced configuration mode” on
page 3-11 on how to determine the
bit rate.
Loss of electrical contact between
the scanner and the monitor (e.g.,
corrosion on the connector inside the
scanner).
If the scanner appears to be working
properly, but will not communicate
with the monitor:
1. Verify that the connector is
properly connected.
2. Verify that the battery door is
securely fastened.
If there is still no communication with
the monitor:
1. Plug and unplug the connector
several times.
2. Rub off any corrosion on the
connector inside the scanner.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Troubleshooting: Alarm code interpretation
Alarm code interpretation
General system error codes are listed in this section. If any other system or
similar code appears, record the error message and report the failure to GE
Technical Support. Refer to the operator’s manual for information about patient
alarms and general procedural alarms.
System failures
System failure mode is entered when the monitor has a depleted battery, or a
hardware or software failure. A distinctive alarm tone is generated for up to 5
minutes, after which if the monitor isn’t turned off, it shuts down completely.
When a system failure is encountered, the error code is displayed on the screen
for > 5 seconds and the system enters FAILSAFE mode. The error code is logged
in the history log.
If the On/Off button remains depressed for between 10 and 20 seconds, a
special situation occurs. It forces a reset and produces a fatal alarm without a
displayed code.
Alarm conditions and error codes
When responding to a monitor alarm, always check the patient first and then
check the monitor, cuff, hose and sensors. Press Silence to clear patient alarm
conditions.
Error log
You can view and print an error log that stores up to 40 error code entries. The
log is a “rolling” list that—once 40 entries are stored—deletes the oldest entry in
order to add the most recent entry. The error log is saved until the monitor
experiences a memory loss, then all entries are deleted.
Procedure to view and print error code history log
2048723-002D
1.
Enter the Advanced Configuration Mode (ACF) by holding down the Minus
(-) and Menu buttons while powering up the monitor (pressing the On/Off
button).
2.
The monitor briefly displays the software revision, then displays ACF in the
Systolic window.
3.
The monitor is now in Advanced Configuration Mode.
4.
To view the error log use the History button to step through the log in
reverse order of when the error occurred (oldest appears first).
5.
The Systolic window shows the Year the error occurred.
6.
The Diastolic window shows the Day the error occurred.
7.
The MAP window shows the Month the error occurred.
8.
The min window shows the Time the error occurred.
CARESCAPE V100 Vital Signs Monitor
5-3
Troubleshooting: Alarm code interpretation
9.
The Pulse Rate window shows the error code that occurred at the recorded
time.
10. To print the error log, press the Print button while viewing the log.
Error codes
Error code or
problem
Source
Display
blank, high
pitch alarm
System
920
Definition
Can be
acknowledged
(silenced)?*
Probable source
FAILSAFE error
No
Mains PWA issue
NIBP
Comm timeout between main
processor and NIBP subprocessor
No
Mains PWA issue
921
NIBP
Startup communication failure with
NIBP processor
No
Mains PWA issue
922
NIBP
NIBP processor reports
communication timeout
No
Mains PWA issue
923
NIBP
Determination time too long
No
Mains PWA issue
930
SpO2
No status from module for 60 ±10 sec.
Fatal error reported by module
No


940
Temp
TEMP data samples less than 45 in 5
sec while idle
No
Mains PWA issue
950
NIBP
NIBP pump on during idle or over
current detected
No
Pneumatic assembly failure
951
NIBP
NIBP valve stuck closed during cuff
typing
No
Pneumatic assembly failure
952
NIBP
NIBP PT2 higher than 150 for greater
than 15 seconds while idle
No
Pneumatic assembly failure
970
Printer
Time base failure
No
Mains PWA issue
971
System
RAM test failure
No
Mains PWA issue
972
System
ROM checksum failure
No
Mains PWA issue
973
System
Secondary processor communication
error during initialization
No
Mains PWA issue
974
System
Calibration data invalid on initialization
or unit never calibrated
No

Could not save calibration data
No
975
5-4
Verify SpO2 configuration
is correct type
Parameter turned on - no
hardware installed in unit
System
CARESCAPE V100 Vital Signs Monitor

Calibrate unit
Mains PWA issue
Mains PWA issue
2048723-002D
Troubleshooting: Alarm code interpretation
Can be
acknowledged
(silenced)?*
Error code or
problem
Source
976
System
Power supply voltage has peaked
above 18 Volts (incorrect power
supply)
No
External power brick issue
979
System
Unknown power processor mode
received on power-up
No
Mains PWA issue
980
System
Heap memory exhausted
No
Mains PWA issue
984
System
Unused vector called
No
Return unit for evaluation
985
System
RTK 400hz timer re-entry
No
Return unit for evaluation
986
System
RTK 50hz timer re-entry
No
Mains PWA issue
989
System
RTK overrun
No
Mains PWA issue
994
System
Stack overflow
No
Mains PWA issue
999
System
Background task stalled
No
Mains PWA issue
E10
Printer
Printer no paper
Yes
No paper in printer
Printer problem
E11
Printer
Printer too hot
Yes
Printer problem
E13
Battery
Main battery low
Yes

Definition
Probable source



Battery too low to
operate the unit
Charge battery
External DC source failed
Replace battery
BATTERY
LOW
Battery
Main battery is running low
Yes
Plug monitor in to recharge
E00
Battery
Memory lost
Yes




Usually noted after
changing batteries.
User settings and date/
time revert to default
settings.
All entries in clinical
history are erased.
For units with Ohmeda
TruSignal technology,
verify the Line Frequency
(LF) mode setting. Refer to
“SpO2 configuration
settings” on page 3-9.
---
SpO2
SpO2 Sensor off finger
Yes
Reposition SpO2 sensor
E20
SpO2
SpO2 sensor disconnected
Yes
Sensor disconnected
E21
SpO2
SpO2 replace sensor
Yes
Replace SpO2 sensor
E25
SpO2
SpO2 lost pulse
Yes
Reposition SpO2 sensor
2048723-002D
CARESCAPE V100 Vital Signs Monitor
5-5
Troubleshooting: Alarm code interpretation
Can be
acknowledged
(silenced)?*
Probable source
Temp probe broken (Alaris only)
No
Replace temperature probe
Temp
Temp probe disconnected (Alaris only)
Yes
Check for correct probe
E66
Temp
Temp probe too hot (Alaris only)
Yes
Replace probe
E--
Temp
Temp scanner error (Exergen only)
Yes
Check Exergen battery, and
check for valid temperature
value. Also check the
scanner’s display for
Exergen error information.
Refer to the “Exergenspecific error codes” section
for more information.
E80
NIBP
Overpressure
Yes
Excess cuff pressure. Check
for pinched or occluded
internal tubing.
E82
NIBP
Excess air in cuff
Yes
Determination cannot be
made due to an excess
amount of air in the cuff.
E83
NIBP
NIBP pump timeout
Yes

E84
NIBP
NIBP total timeout
Yes
Length of time has
exceeded 2 minutes for an
adult/pediatric
determination or 85
seconds for a neonate
determination.
E85
NIBP
NIBP level timeout
Yes
Remained at one cuff
pressure level for more than
1 minute.
E89
NIBP
NIBP no determination
Yes
Cuff placement on patient
Error code or
problem
Source
E61
Temp
E63
Definition
Leak in cuff or o-ring in
hose
 Internal leak in tubing or
pneumatic valve
 Pump not turning on
Check or replace hose or
cuff.
*Acknowledging an alarm by pressing the Silence button, cancels and resets the alarm condition.
5-6
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Troubleshooting: Alarm code interpretation
Exergen-specific error codes
If the scanner is unable to take a temperature determination, or has a low
battery, the monitor will display the ‘E--’ error code and generate an audible
alarm. The scanner may also display additional indicators on the LED display.
Exergen LED display
Condition
Description
HI
High Target
> 43 °C (110 °F)
LO
Low Target
< 16 °C (61 °F)
HI A
High Ambient
> 40 °C (104 °F)
LO A
Low Ambient
< 16 °C (60 °F)
bAtt
Low Battery
Replace battery soon.
(blank display)
Dead Battery
Replace battery.
Err
Processing Error
Restart scanner. If unit is defective, it will have to be returned to the
manufacturer. Contact GE Technical Support.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
5-7
Troubleshooting: Alarm code interpretation
For your notes
5-8
CARESCAPE V100 Vital Signs Monitor
2048723-002D
6
2048723-002D
Parts lists and
drawings
CARESCAPE V100 Vital Signs Monitor
6-1
Parts lists and drawings: Ordering parts
Ordering parts
This section of the manual provides parts lists for the monitor. Parts lists should
be used in conjunction with the other chapters of this manual.
GE makes every effort possible to provide the most up-to-date reference
documentation for your equipment. However, in special cases involving fieldinstalled upgrades, the revision level of a diagram or parts list in this manual
may not reflect the revision level of your unit’s subassemblies. When
discrepancies are found, contact your GE Service Representative.
NOTE
Fabrication drawings are not contained in this manual.
Compatible service parts
NIBP accessories
Part
Part description
Part number
NIBP, Cuff, Soft Cuff, Child
SOFT-CUF, Child, 2 TB, Mated Submin, Green/White 12 - 19 cm
2451
NIBP, Cuff, Soft Cuff, Sm
Adult
SOFT-CUF, Small Adult, 2 TB, Mated Submin, Lt. Blue/White 17 - 25 cm
2452
NIBP, Cuff, Soft Cuff, Adult
SOFT-CUF, Adult, 2 TB, Mated Submin, Navy/White 23 - 33 cm
2453
NIBP, Cuff, Soft Cuff, Adult
Long
SOFT-CUF, Adult Long, 2 TB, Mated Submin, Navy/White 23 - 33 cm
2454
NIBP, Cuff, Soft Cuff, Lg Adult SOFT-CUF, Large Adult, 2 TB, Mated Submin, Rose/White 31 - 40 cm
2455
NIBP, Cuff, Soft Cuff, Lg Adult
Long
SOFT-CUF, Large Adult Long, 2 TB, Mated Submin, Rose/White 31 - 40
cm
2456
NIBP, Cuff, Soft Cuff, Thigh
SOFT-CUF, Thigh, 2 TB, Mated Submin, Brown/White 38 - 50 cm
2457
NIBP, Cuff, Soft Cuff, Infant
SOFT-CUF, Infant, 2 TB, Submin, Orange/White 8 - 13 cm
2401
NIBP, Cuff, Soft Cuff, Child
SOFT-CUF, Child, 2 TB, Submin, Green/White 12 - 19 cm
2402
NIBP, Cuff, Soft Cuff, Child
Long
SOFT-CUF, Child Long, 2 TB, Submin, Green/White 12 - 19 cm
2400
NIBP, Cuff, Soft Cuff, Sm
Adult
SOFT-CUF, Small Adult, 2 TB, Submin, Lt. Blue/White 17 - 25 cm
2403
NIBP, Cuff, Soft Cuff, Sm
Adult Long
SOFT-CUF, Small Adult Long, 2 TB, Submin, Lt. Blue/White 17 - 25 cm
2407
NIBP, Cuff, Soft Cuff, Adult
SOFT-CUF, Adult, 2 TB, Submin, Navy/White 23 - 33 cm
2404
NIBP, Cuff, Soft Cuff, Adult
Long
SOFT-CUF, Adult Long, 2 TB, Submin, Navy/White 23 - 33 cm
2116
NIBP, Cuff, Soft Cuff, Lg Adult SOFT-CUF, Large Adult, 2 TB, Submin, Rose/White 31 - 40 cm
2405
NIBP, Cuff, Soft Cuff, Lg Adult
Long
SOFT-CUF, Large Adult Long, 2 TB, Submin, Rose/White 31 - 40 cm
2117
NIBP, Cuff, Soft Cuff, Thigh
SOFT-CUF, Thigh, 2 TB, Submin, Brown/White 38 - 50 cm
2406
6-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
NIBP, Cuff, Soft Cuff, Infant
SOFT-CUF, Infant, 2 TB, Screw, Orange/White 8 - 13 cm
2500
NIBP, Cuff, Soft Cuff, Child
SOFT-CUF, Child, 2 TB, Screw, Green/White 12 - 19 cm
2501
NIBP, Cuff, Soft Cuff, Child
Long
SOFT-CUF, Child Long, 2 TB, Screw, Green/White 12 - 19 cm
2506
NIBP, Cuff, Soft Cuff, Sm
Adult
SOFT-CUF, Small Adult, 2 TB, Screw, Lt. Blue/White 17 - 25 cm
2502
NIBP, Cuff, Soft Cuff, Sm
Adult Long
SOFT-CUF, Small Adult Long, 2 TB, Screw, Lt. Blue/White 17 - 25 cm
2507
NIBP, Cuff, Soft Cuff, Adult
SOFT-CUF, Adult, 2 TB, Screw, Navy/White 23 - 33 cm
2503
NIBP, Cuff, Soft Cuff, Adult
Long
SOFT-CUF, Adult Long, 2 TB, Screw, Navy/White 23 - 33 cm
2604
NIBP, Cuff, Soft Cuff, Lg Adult SOFT-CUF, Large Adult, 2 TB, Screw, Rose/White 31 - 40 cm
2504
NIBP, Cuff, Soft Cuff, Lg Adult
Long
SOFT-CUF, Large Adult Long, 2 TB, Screw, Rose/White 31 - 40 cm
2644
NIBP, Cuff, Soft Cuff, Thigh
SOFT-CUF, Thigh, 2 TB, Screw, Brown/White 38 - 50 cm
2505
NIBP, Cuff, Soft Cuff, Various
SOFT-CUF, Assortment, 2 TB, Submin: 1 Infant, 1 Child, Various limb
circum: 2 Small Adult, 2 Adult, 1 Adult Long, 2 Large Adult, 1 Thigh
2298
NIBP, Cuff, Soft Cuff, Various
SOFT-CUF, Assortment Pack: 2 TB, Screw, 1 Infant, 1 Child, 2 Small
Adult, 2 Adult, 1 Adult Long, 2 Large Adult, 1 Thigh
002695
NIBP, Cuff, Soft Cuff,
Neonate
SOFT-CUF, Neonatal #1, 2 TB, Male Slip, Orange/White 3 - 6 cm
2521
NIBP, Cuff, Soft Cuff,
Neonate
SOFT-CUF, Neonatal #2, 2 TB, Male Slip, Lt. Blue/White 4 - 8 cm
2422
NIBP, Cuff, Soft Cuff,
Neonate
SOFT-CUF, Neonatal #3, 2 TB, Male Slip, Green/White 6 - 11 cm
2523
NIBP, Cuff, Soft Cuff,
Neonate
SOFT-CUF, Neonatal #4, 2 TB, Male Slip, Navy/White 7 - 13 cm
2524
NIBP, Cuff, Soft Cuff,
Neonate
SOFT-CUF, Neonatal #5, 2 TB, Male Slip, Rose/White 8 - 15 cm
2525
NIBP, Cuff, Soft Cuff,
Neonate
SOFT-CUF, Neonatal Assortment, 2 TB, Male Slip: Various limb circum: 2
Neonatal #1, 3 Neonatal #2, 5 Neonatal #3, 5 Neonatal #4, 5 Neonatal
#5
2694
NIBP, Cuff, Classic Cuff, Child CLASSIC-CUF, Child, 2 TB, Mated Submin, Green/White 12 - 19 cm
2171
NIBP, Cuff, Classic Cuff, Sm
Adult
2172
CLASSIC-CUF, Small Adult, 2 TB, Mated Submin, Lt. Blue/White
17 - 25 cm
NIBP, Cuff, Classic Cuff, Adult CLASSIC-CUF, Adult, 2 TB, Mated Submin, Navy/White 23 - 33 cm
2173
NIBP, Cuff, Classic Cuff, Adult
Long
CLASSIC-CUF, Adult Long, 2 TB, Mated Submin, Navy/White 23 - 33 cm
2174
NIBP, Cuff, Classic Cuff, Lg
Adult
CLASSIC-CUF, Large Adult, 2 TB, Mated Submin, Rose/White 31 - 40 cm 2175
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-3
Parts lists and drawings: Compatible service parts
Part
NIBP, Cuff, Classic Cuff, Lg
Adult Long
Part description
CLASSIC-CUF, Large Adult Long, 2 TB, Mated Submin, Rose/White 31 40 cm
Part number
2176
NIBP, Cuff, Classic Cuff, Thigh CLASSIC-CUF, Thigh, 2 TB, Mated Submin, Brown/White 38 - 50 cm
2177
NIBP, Cuff, Classic Cuff,
Infant
2354
CLASSIC-CUF, Infant, 2 TB, Submin, Orange/White 8 - 13 cm
NIBP, Cuff, Classic Cuff, Child CLASSIC-CUF, Child, 2 TB, Submin, Green/White 12 - 19 cm
2355
NIBP, Cuff, Classic Cuff, Sm
Adult
2356
CLASSIC-CUF, Small Adult, 2 TB, Submin, Lt. Blue/White 17 - 25 cm
NIBP, Cuff, Classic Cuff, Adult CLASSIC-CUF, Adult, 2 TB, Submin, Navy/White 23 - 33 cm
2357
NIBP, Cuff, Classic Cuff, Adult
Long
CLASSIC-CUF, Adult Long, 2 TB, Submin, Navy/White 23 - 33 cm
2352
NIBP, Cuff, Classic Cuff, Lg
Adult
CLASSIC-CUF, Large Adult, 2 TB, Submin, Rose/White 31 - 40 cm
2358
NIBP, Cuff, Classic Cuff, Lg
Adult Long
CLASSIC-CUF, Large Adult Long, 2 TB, Submin, Rose/White 31 - 40 cm
2353
NIBP, Cuff, Classic Cuff, Thigh CLASSIC-CUF, Thigh, 2 TB, Submin, Brown/White 38 - 50 cm
2359
NIBP, Cuff, Classic Cuff,
Infant
2618
CLASSIC-CUF, Infant, 2 TB, Screw, Orange/White 8 - 13 cm
NIBP, Cuff, Classic Cuff, Child CLASSIC-CUF, Child, 2 TB, Screw, Green/White 12 - 19 cm
2613
NIBP, Cuff, Classic Cuff, Sm
Adult
2608
CLASSIC-CUF, Small Adult, 2 TB, Screw, Lt. Blue/White 17 - 25 cm
NIBP, Cuff, Classic Cuff, Adult CLASSIC-CUF, Adult, 2 TB, Screw, Navy/White 23 - 33 cm
2603
NIBP, Cuff, Classic Cuff, Adult
Long
CLASSIC-CUF, Adult Long, 2 TB, Screw, Navy/White 23 - 33 cm
2647
NIBP, Cuff, Classic Cuff, Lg
Adult
CLASSIC-CUF, Large Adult, 2 TB, Screw, Rose/White 31 - 40 cm
2643
NIBP, Cuff, Classic Cuff, Lg
Adult Long
CLASSIC-CUF, Large Adult Long, 2 TB, Screw, Rose/White 31 - 40 cm
2649
NIBP, Cuff, Classic Cuff, Thigh CLASSIC-CUF, Thigh, 2 TB, Screw, Brown/White 38 - 50 cm
2648
NIBP, Cuff, Classic Cuff,
Various
CLASSIC-CUF, Assortment, 2 TB, Submin: 1 Infant, 1 Child, Various limb
circum: 2 Small Adult, 2 Adult, 1 Adult Long, 2 Large Adult, 1 Thigh
2292
NIBP, Cuff, Classic Cuff,
Various
CLASSIC-CUF, Assortment, 2 TB, Screw: 1 Infant, 1 Child, Various limb
circum: 2 Small Adult, 2 Adult, 1 Adult Long, 2 Large Adult, 1 Thigh
2692
NIBP, Cuff, Classic Cuff,
Infant
CLASSIC-CUF, Infant, 2 TB, Submin, Yellow 8 - 13 cm
2670
NIBP, Cuff, Classic Cuff, Child CLASSIC-CUF, Child, 2 TB, Submin, Yellow 12 - 19 cm
2671
NIBP, Cuff, Classic Cuff, Sm
Adult
2672
CLASSIC-CUF, Small Adult, 2 TB, Submin, Yellow 17 - 25 cm
NIBP, Cuff, Classic Cuff, Adult CLASSIC-CUF, Adult, 2 TB, Submin, Yellow 23 - 33 cm
2673
NIBP, Cuff, Classic Cuff, Lg
Adult
2674
6-4
CLASSIC-CUF, Large Adult, 2 TB, Submin, Yellow 31 - 40 cm
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
NIBP, Cuff, Classic Cuff, Thigh CLASSIC-CUF, Thigh, 2 TB, Submin, Yellow 38 - 50 cm
2675
NIBP, Cuff, Classic Cuff,
Infant
CLASSIC-CUF, Infant, 2 TB, Submin, Yellow 8 - 13 cm
2650
NIBP, Cuff, Classic Cuff, Child CLASSIC-CUF, Child, 2 TB, Submin, Yellow 12 - 19 cm
2651
NIBP, Cuff, Classic Cuff, Sm
Adult
2607
CLASSIC-CUF, Small Adult, 2 TB, Submin, Yellow 17 - 25 cm
NIBP, Cuff, Classic Cuff, Adult CLASSIC-CUF, Adult, 2 TB, Submin, Yellow 23 - 33 cm
2602
NIBP, Cuff, Classic Cuff, Lg
Adult
2642
CLASSIC-CUF, Large Adult, 2 TB, Submin, Yellow 31 - 40 cm
NIBP, Cuff, Classic Cuff, Thigh CLASSIC-CUF, Thigh, 2 TB, Submin, Yellow 38 - 50 cm
2652
NIBP, Cuff, Classic Cuff,
Neonate
CLASSIC-CUF, Neonatal #1, 2 TB, Male Slip, White 3 - 6 cm
2638
NIBP, Cuff, Classic Cuff,
Neonate
CLASSIC-CUF, Neonatal #2, 2 TB, Male Slip, White 4 - 8 cm
2633
NIBP, Cuff, Classic Cuff,
Neonate
CLASSIC-CUF, Neonatal #3, 2 TB, Male Slip, White 6 - 11 cm
2628
NIBP, Cuff, Classic Cuff,
Neonate
CLASSIC-CUF, Neonatal #4, 2 TB, Male Slip, White 7 - 13 cm
2623
NIBP, Cuff, Classic Cuff,
Neonate
CLASSIC-CUF, Neonatal #5, 2 TB, Male Slip, White 8 - 15 cm
2619
NIBP, Cuff, Classic Cuff,
Neonate
CLASSIC-CUF, Neonatal Assortment, 2 TB, Male Slip, White: Various limb
circum: 2 Neonatal #1, 3 Neonatal #2, 5 Neonatal #3, 5 Neonatal #4, 5
Neonatal #5
2693
NIBP, Cuff, Sensa Cuff, Infant SENSA-CUF, Infant, 2 TB, Mated Submin, Rust 8 - 13 cm
2430
NIBP, Cuff, Sensa Cuff, Child
SENSA-CUF, Child, 2 TB, Mated Submin, Green 12 - 19 cm
2431
NIBP, Cuff, Sensa Cuff, Sm
Adult
SENSA-CUF, Small Adult, 2 TB, Mated Submin, Royal Blue 17 - 25 cm
2432
NIBP, Cuff, Sensa Cuff, Sm
Adult Long
SENSA-CUF, Small Adult Long, 2 TB, Mated Submin, Royal Blue
17 - 25 cm
2433
NIBP, Cuff, Sensa Cuff, Adult
SENSA-CUF, Adult, 2 TB, Mated Submin, Navy 23 - 33 cm
2434
NIBP, Cuff, Sensa Cuff, Adult
Long
SENSA-CUF, Adult Long, 2 TB, Mated Submin, Navy 23 - 33 cm
2435
NIBP, Cuff, Sensa Cuff, Lg
Adult
SENSA-CUF, Large Adult, 2 TB, Mated Submin, Wine 31 - 40 cm
2436
NIBP, Cuff, Sensa Cuff, Lg
Adult Long
SENSA-CUF, Large Adult Long, 2 TB, Mated Submin, Wine 31 - 40 cm
2437
NIBP, Cuff, Sensa Cuff, Thigh
SENSA-CUF, Thigh, 2 TB, Mated Submin, Brown 38 - 50 cm
2438
NIBP, Cuff, Sensa Cuff, Infant SENSA-CUF, Infant, 2 TB, Submin, Rust 8 - 13 cm
2482
NIBP, Cuff, Sensa Cuff, Child
SENSA-CUF, Child, 2 TB, Submin, Green 12 - 19 cm
2484
NIBP, Cuff, Sensa Cuff, Sm
Adult
SENSA-CUF, Small Adult, 2 TB, Submin, Royal Blue 17 - 25 cm
2486
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-5
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
NIBP, Cuff, Sensa Cuff, Sm
Adult Long
SENSA-CUF, Small Adult Long, 2 TB, Submin, Royal Blue 17 - 25 cm
2487
NIBP, Cuff, Sensa Cuff, Adult
SENSA-CUF, Adult, 2 TB, Submin, Navy 23 - 33 cm
2488
NIBP, Cuff, Sensa Cuff, Adult
Long
SENSA-CUF, Adult Long, 2 TB, Submin, Navy 23 - 33 cm
2489
NIBP, Cuff, Sensa Cuff, Lg
Adult
SENSA-CUF, Large Adult, 2 TB, Submin, Wine 31 - 40 cm
2490
NIBP, Cuff, Sensa Cuff, Lg
Adult Long
SENSA-CUF, Large Adult Long, 2 TB, Submin, Wine 31 - 40 cm
2491
NIBP, Cuff, Sensa Cuff, Thigh
SENSA-CUF, Thigh, 2 TB, Submin, Brown 38 - 50 cm
2492
NIBP, Cuff, Sensa Cuff, Infant SENSA-CUF, Infant, 2 TB, Screw, Rust 8 - 13 cm
2458
NIBP, Cuff, Sensa Cuff, Child
SENSA-CUF, Child, 2 TB, Screw, Green 12 - 19 cm
2460
NIBP, Cuff, Sensa Cuff, Sm
Adult
SENSA-CUF, Small Adult, 2 TB, Screw, Royal Blue 17 - 25 cm
2462
NIBP, Cuff, Sensa Cuff, Sm
Adult Long
SENSA-CUF, Small Adult Long, 2 TB, Screw, Royal Blue 17 - 25 cm
2463
NIBP, Cuff, Sensa Cuff, Adult
SENSA-CUF, Adult, 2 TB, Screw, Navy 23 - 33 cm
2464
NIBP, Cuff, Sensa Cuff, Adult
Long
SENSA-CUF, Adult Long, 2 TB, Screw, Navy 23 - 33 cm
2465
NIBP, Cuff, Sensa Cuff, Lg
Adult
SENSA-CUF, Large Adult, 2 TB, Screw, Wine 31 - 40 cm
2466
NIBP, Cuff, Sensa Cuff, Lg
Adult Long
SENSA-CUF, Large Adult Long, 2 TB, Screw, Wine 31 - 40 cm
2467
NIBP, Cuff, Sensa Cuff, Thigh
SENSA-CUF, Thigh, 2 TB, Screw, Brown 38 - 50 cm
2468
NIBP, Cuff, Sensa Cuff,
Various
SENSA-CUF, Assortment Pack: 2 TB, Screw, 1 sm Adult, 1 Adult, 1 Lg
Adult
2494
NIBP, Cuff, Dura Cuff, Child
DURA-CUF, Child, 2 TB, Mated Submin, Green 12 - 19 cm
2751
NIBP, Cuff, Dura Cuff, Sm
Adult
DURA-CUF, Small Adult, 2 TB, Mated Submin, Royal Blue 17 - 25 cm
2752
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult, 2 TB, Mated Submin, Navy 23 - 33 cm
2753
NIBP, Cuff, Dura Cuff, Adult
Long
DURA-CUF, Adult Long, 2 TB, Mated Submin, Navy 23 - 3 3cm
002756
NIBP, Cuff, Dura Cuff, Lg
Adult
DURA-CUF, Large Adult, 2 TB, Mated Submin, Wine 31 - 40 cm
2754
NIBP, Cuff, Dura Cuff, Lg
Adult Long
DURA-CUF, Large Adult Long, 2 TB, Mated Submin, Wine 31 - 40 cm
002757
NIBP, Cuff, Dura Cuff, Thigh
DURA-CUF, Thigh, 2 TB, Mated Submin, Brown 38 - 50 cm
2755
NIBP, Cuff, Dura Cuff, Child
DURA-CUF, Child, 2 TB, Mated Submin, Green 12 - 19 cm
2751E
NIBP, Cuff, Dura Cuff, Sm
Adult
DURA-CUF, Small Adult, 2 TB, Mated Submin, Royal Blue 17 - 25 cm
2752E
6-6
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult, 2 TB, Mated Submin, Navy 23 - 33 cm
2753E
NIBP, Cuff, Dura Cuff, Adult
Long
DURA-CUF, Adult Long, 2 TB, Mated Submin, Navy 23 - 33 cm
002756E
NIBP, Cuff, Dura Cuff, Lg
Adult
DURA-CUF, Large Adult, 2 TB, Mated Submin, Wine 31 - 40 cm
2754E
NIBP, Cuff, Dura Cuff, Lg
Adult Long
DURA-CUF, Large Adult Long, 2 TB, Mated Submin, Wine 31 - 40 cm
002757E
NIBP, Cuff, Dura Cuff, Thigh
DURA-CUF, Thigh, 2 TB, Mated Submin, Brown 38 - 50 cm
2755E
NIBP, Cuff, Dura Cuff, Infant
DURA-CUF, Infant, 2 TB, Submin, Rust 8 - 13 cm
002200
NIBP, Cuff, Dura Cuff, Child
DURA-CUF, Child, 2 TB, Submin, Green 12 - 19 cm
002201
NIBP, Cuff, Dura Cuff, Sm
Adult
DURA-CUF, Small Adult, 2 TB, Submin, Royal Blue 17 - 25 cm
002202
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult, 2 TB, Submin, Navy 23 - 33 cm
002203
NIBP, Cuff, Dura Cuff, Adult
Long
DURA-CUF, Adult Long, 2 TB, Submin, Navy 23 - 33 cm
002206
NIBP, Cuff, Dura Cuff, Lg
Adult
DURA-CUF, Large Adult, 2 TB, Submin, Wine 31 - 40 cm
002204
NIBP, Cuff, Dura Cuff, Lg
Adult Long
DURA-CUF, Large Adult Long, 2 TB, Submin, Wine 31 - 40 cm
002207
NIBP, Cuff, Dura Cuff, Thigh
DURA-CUF, Thigh, 2 TB, Submin, Brown 38 - 50 cm
002205
NIBP, Cuff, Dura Cuff, Infant
DURA-CUF, Infant, 2 TB, Screw, Rust 8 - 13 cm
002783
NIBP, Cuff, Dura Cuff, Child
DURA-CUF, Child, 2 TB, Screw, Green 12 - 19 cm
002781
NIBP, Cuff, Dura Cuff, Child
Long
DURA-CUF, Child Long, 2 TB, Screw, Green 12 - 19 cm
2785
NIBP, Cuff, Dura Cuff, Sm
Adult
DURA-CUF, Small Adult, 2 TB, Screw, Royal Blue 17 - 25 cm
002779
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult with Hanger, 2 TB, Screw, Navy 23 - 33 cm
002771
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult, 2 TB, Screw, Navy 23 - 33 cm
002774
NIBP, Cuff, Dura Cuff, Adult
Long
DURA-CUF, Adult Long, 2 TB, Screw, Navy 23 - 33 cm
002772
NIBP, Cuff, Dura Cuff, Lg
Adult
DURA-CUF, Large Adult, 2 TB, Screw, Wine 31 - 40 cm
002791
NIBP, Cuff, Dura Cuff, Lg
Adult Long
DURA-CUF, Large Adult Long, 2 TB, Screw, Wine 31 - 40 cm
002784
NIBP, Cuff, Dura Cuff, Thigh
DURA-CUF, Thigh, 2 TB, Screw, Brown 38 - 50 cm
002796
NIBP, Cuff, Dura Cuff, Child
DURA-CUF, Child Assortment, 2 TB, Submin: 2 Infant, 3 Child, 1 Small
Adult, Various limb circum
2296
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult Assortment, 2 TB, Submin: 1 Small Adult, 2 Adult, 1
Adult Long, 1 Large Adult, 1 Large Adult Long, Various limb circum
2297
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-7
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
NIBP, Cuff, Dura Cuff, Various DURA-CUF, Assortment, 2 TB, Submin: 1 Infant, 1 Child, 1 Small Adult, 1
Adult, 1 Large Adult, 1 Thigh, Various limb circum
2299
NIBP, Cuff, Dura Cuff, Various DURA-CUF, Assortment, 2 TB, Screw: 1 Infant, 1 Child, 1 Small Adult, 1
Adult, 1 Large Adult, 1 Thigh, Various limb circum
002699
NIBP, Cuff, Dura Cuff, Child
DURA-CUF, Child Assortment, 2 TB, Screw: 2 Infant, 3 Child, 1 Small
Adult, Various limb circum
002697
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult Assortment, 2 TB, Screw: 1 Small Adult, 2 Adult, 1
Adult Long, 1 Large Adult, 1 Large Adult Long, Various limb circum
002698
NIBP, Cuff, Dura Cuff, Infant
DURA-CUF, Infant, 2 TB, Submin, Rust 8 - 13 cm
002200E
NIBP, Cuff, Dura Cuff, Child
DURA-CUF, Child, 2 TB, Submin, Green 12 - 19 cm
002201E
NIBP, Cuff, Dura Cuff, Sm
Adult
DURA-CUF, Small Adult, 2 TB, Submin, Royal Blue 17 - 25 cm
002202E
NIBP, Cuff, Dura Cuff, Adult
DURA-CUF, Adult, 2 TB, Submin, Navy 23 - 33 cm
002203E
NIBP, Cuff, Dura Cuff, Adult
Long
DURA-CUF, Adult Long, 2 TB, Submin, Navy 23 - 33 cm
002206E
NIBP, Cuff, Dura Cuff, Lg
Adult
DURA-CUF, Large Adult, 2 TB, Submin, Wine 31 - 40 cm
002204E
NIBP, Cuff, Dura Cuff, Lg
Adult Long
DURA-CUF, Large Adult Long, 2 TB, Submin, Wine 31 - 40 cm
002207E
NIBP, Cuff, Dura Cuff, Thigh
DURA-CUF, Thigh, 2 TB, Submin, Brown 38 - 50 cm
002205E
NIBP, Adult, 1 2ft
Air hose adult/ped 12 ft, gray
107365
NIBP, Neonate, 12 ft
Air hose, neonatal 12 ft, light blue
107368
NIBP, Adult, 24 ft
Air hose adult/ped 24 ft, gray
107366
NIBP, Cuff hose caps
Cuff hose caps (washing plugs), 50/pk
300877
NIBP, Cuff hose caps,
Subminiature
Cuff hose caps (washing plugs), subminiature, 50/pk
330072
6-8
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Compatible service parts
SpO2 - Ohmeda accessories
Part
Part description
Part number
SpO2 - Cable Assy
TruSignal Interconnect cable with GE connector
TS-G3
SpO2 - Sensor
TruSignal Finger Sensor with integrated cable, 2 m
TS-F2-GE
SpO2 - Sensor
TruSignal Finger Sensor with integrated cable, 4 m
TS-F4-GE
SpO2 - Sensor
TruSignal Finger Sensor
TS-F-D
SpO2 - Sensor
TruSignal Soft Adult Sensor with integrated cable and D
connector, 1 m
TS-SA-D
SpO2 - Sensor
TruSignal Soft Adult Sensor with integrated cable and GE
connector, 4 m
TS-SA4-GE
SpO2 - Sensor
TruSignal Wrap Sensor
TS-W-D
SpO2 - Sensor
TruSignal Ear Sensor with integrated cable, 4 m
TS-E4-GE
SpO2 - Sensor
TruSignal Ear Sensor with integrated cable, 2 m
TS-E2-GE
SpO2 - Sensor
TruSignal Ear Sensor
TS-E-D
SpO2 - Sensor
TruSignal Sensitive Skin Sensor
TS-SE-3
SpO2 - Sensor
TruSignal AllFit Sensor, 10/box
TS-AF-10
SpO2 - Sensor
TruSignal AllFit Sensor, 25/box
TS-AF-25
SpO2 - Accessory
Wide replacement tape, adhesive
OXY-RTW
SpO2 - Accessory
Foam wrap replacement, large, weight range > 3 kg
OXY-RWL
SpO2 - Accessory
Foam wrap replacement, medium, weight range > 3 kg
OXY-RWM
SpO2 - Accessory
Foam wrap replacement, small, weight range < 3 kg
OXY-RWS
SpO2 - Accessory
Replacement tape, AllFit Sensor, Bears - 100/box
OXY-RTB
SpO2 - Accessory
Replacement tape, AllFit Sensor, Blue - 100/box
OXY-RT
SpO2 - Accessory
Infant Foam Sandal, use with OxyTip++ Sensitive Skin
sensor - 3/box
OXY-SND
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-9
Parts lists and drawings: Compatible service parts
SpO2 - Nellcor accessories
Part
Part description
Part number
SpO2 Cable Assy 3 m
Cable Assy SpO2 Nellcor OxiMax 3 m - Smart
2021406-001
SpO2 Cable Assy 3 m
Cable Assy SpO2 Nellcor OxiMax 1.2 m - Smart
2021406-002
SpO2 - Sensor
Max -A Adult Finger Adhesive Sensor - 24/box
70124027
SpO2 - Sensor
Max -AL Adult Long Finger Adhesive Sensor - 24/box
2028117-001
SpO2 - Sensor
Max-P Pediatric Finger Adhesive Sensor - 24/box
70124022
SpO2 - Sensor
Max-N Neonate Foot Adhesive Sensor - 24/box
70124032
SpO2 - Sensor
Max-I Infant, Adhesive, Sensor - 24/box
70124026
SpO2 - Sensor
Max-R, Adhesive, Nasal - 24/box
407705-005
SpO2 - Sensor
OXIBAND (OXI-P/I) Pediatric/Infant Sensor
414248-001
SpO2 - Sensor
OXIBAND (OXI-A/N) Adult/Neonate Sensor
414248-002
SpO2 - Sensor
OXIBAND (OXI-A/N) Adult/Neonate Sensor
70124035 (EMEA)
SpO2 - Sensor
Nellcor Multisite Sensor D-YS Reusable
70124033
SpO2 - Sensor
Nellcor DuraSensor DS-100A
70124021
SpO2 - Sensor
Nellcor DuraSensor DS-100A
407705-006 (US)
SpO2 - Accessory
Nellcor Ear-Clip D-YSE Sensor for 70124033
70124034
SpO2 - Accessory
Nellcor Tape ADH-A/N, use with 70124035
2016130-001
SpO2 - Accessory
Nellcor Tape ADH-P/I, use with Oxi-P/I Sensors
2016131-001
SpO2 - Masimo accessories
Part
Part description
Part number
SpO2 - Sensor
Masimo LNOP Disposable Adhesive Sensor, LNOP Adt.
Adult - 20/box
2010458-001
SpO2 - Sensor
Masimo LNOP Disposable Adhesive Sensor, LNOP Pdt.
Pediatric - 20/box
2010459-001
SpO2 - Sensor
Masimo LNOP Disposable Adhesive Sensor, LNOP NeoPT.
Neonatal - 20/box
2010461-001
SpO2 - Sensor
Masimo LNOP Disposable Adhesive Sensor Bridge, LNOP
Neo. Neonatal - 20/box
2010460-001
6-10
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
SpO2 - Sensor
Masimo LNOP Disposable Adhesive Sensor, LNOP-Neo-L.
Neonatal - 20/box
2017089-001
SpO2 - Sensor
Masimo LNOP Disposable Adhesive Sensor, LNOP NeoPTL. Neonatal - 20/box
2017090-001
SpO2 - Sensor
Masimo LNOP Adtx Disposable Adhesive Sensor
Transparent Tape LNOP, Adult - 20/box
2027269-001
SpO2 - Sensor
Masimo LNOP Pdtx Disposable Adhesive Sensor
Transparent Tape LNOP, Pediatric - 20/box
2027270-001
SpO2 - Sensor
Masimo LNOP Disposable LNOP Disposable LNOP Hi Fi
Sensor Neonatal/Adult - 20/box
2027272-001
SpO2 - Sensor
Masimo LNOP Disposable LNOP Disposable LNOP Hi Fi
Sensor Infant/Pediatric - 20/box
2027271-001
SpO2 - Sensor
Masimo LNOP Disposable LNOP Disposable LNOP Blue
Infant Thumb/Toe Sensor - 20/box
2027273-001
SpO2 - Sensor
Masimo LNOP Reusable Finger Sensor LNOP/DCIP
Pediatric
2002799-001
SpO2 - Sensor
Masimo LNOP Reusable Finger Sensor LNOP/DCI Adult,
LNOP/DCI
2002800-001
SpO2 - Sensor
Masimo LNOP Reusable Multisite Sensor LNOP-YI
2010463-001
SpO2 - Sensor
Masimo LNOP Reusable Tip-Clip Ear Sensor LKNOP TC-I
2027274-001
SpO2 - Sensor
Masimo LNOP Reusable Finger Sensor Adult DC-195
2009745-001
SpO2 - Sensor
Masimo LNCS DCI Reusable Adult Sensor
2027258-001
SpO2 - Sensor
Masimo LNCS DCIP Reusable Pediatric Sensor
2027259-001
SpO2 - Sensor
Masimo LNCS TC-I TipClip Reusable Ear Sensor
2027261-001
SpO2 - Sensor
Masimo LNCS Adult, Transparent Adhesive Sensor - 20/
box
2027253-001
SpO2 - Sensor
Masimo LNCS Pdtx Pediatric Adhesive Sensor - 20/box
2027254-001
SpO2 - Sensor
Masimo LNCS Inf-L Infant Adhesive Sensor - 20/box
2027255-001
SpO2 - Sensor
Masimo LNCS Neo-L Neonatal Adhesive Sensor - 20/box
2027256-001
SpO2 - Sensor
Masimo LNCS NeoPt-L Neonatal PT Adhesive Sensor
- 20/box
2027257-001
SpO2 - Cable Assy - 2.4 m
Masimo LNOP, SpO2 2.4 m
2017002-003
SpO2 - Cable Assy - 3.6 m
Masimo LNOP, SpO2 3.6 m
2017002-001
SpO2 - Cable Assy - 3 m
Masimo LNC-10, SpO2 3 m
2027263-002
SpO2 - Accessory
Masimo Replacement Posey Wrap, LNOP-NeoPt-L,
Neonatal - 12/box
2010466-001
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-11
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
SpO2 - Accessory
Masimo Tape Bag for LNOP-NEO - 100/box
2010467-001
SpO2 - Accessory
Masimo Tape Cleanshield Multisite, LNOP-YI - 100/box
2010468-001
SpO2 - Accessory
Masimo Disposable Standard Multisite Wrap, Adult/Ped/
Neonatal Adhesive Attachment Wraps, use with LNOP-YI
Multisite Reusable Sensor - 100/box
2010469-001
SpO2 - Accessory
Masimo Tape Standard Petite Wrap, LNOP-YI - 100/box
2010470-001
SpO2 - Accessory
Masimo Adhesive Tape for LNOP-YI - 12/box
2010471-001
Temperature accessories - Alaris
Part
Part description
Part number
Alaris Temperature, Oral Probe
Sensor Turbo Temp Temperature, Long, White Cord (Blue)
2008774-001
Alaris Temperature, Rectal Probe
Sensor Turbo Temp Temperature, Long Rectal, White
Cord (Red)
2008775-001
Alaris Temperature, Oral Probe
Sensor Tri-Site Temperature, Long, White Cord (Blue)
2041178-001
Alaris Temperature, Rectal Probe
Sensor Tri-Site Temperature, Long Rectal, White Cord
(Red)
2041179-001
Alaris Probe Covers
Probe covers - case
088015
Temperature accessories - Exergen
Part
Part description
Part number
Exergen Temporal Scanner,
Fahrenheit - arterial
Exergen TAT-5000 temporal scanner with cable interface
to the V100, reporting in °F calibrated to arterial reference
2044860-001
Exergen Temporal Scanner, Celsius
- arterial
Exergen TAT-5000 temporal scanner with cable interface
to the V100, reporting in °C calibrated to arterial
reference
2044860-002
Exergen Temporal Scanner, Celsius
- oral
Exergen TAT-5000 temporal scanner with cable interface
to the V100, reporting in °C calibrated to an oral reference
2044860-003
Exergen Temporal Scanner,
Fahrenheit - oral
Exergen TAT-5000 temporal scanner with cable interface
to the V100, reporting in °F calibrated to an oral reference
2044860-004
Exergen Scanner Disposable Caps
Protective covers - rigid plastic covers probe cone, 1000/
box
EX134203
Exergen Scanner Disposable Caps
Protective covers - rigid plastic covers probe cone, 5000/
box
EX134205
Exergen Scanner Disposable
Sheath
Disposable tubular protective sheath, 250/box
EX129462
6-12
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Compatible service parts
Part
Part description
Part number
Cable - Exergen
Cable, Exergen TAT-5000 to V100 interface
2044860-005
Calibration - Exergen, Fahrenheit arterial
Exergen calibration verification kit for °F calibrated to an
arterial reference
EX129003
Exergen Scanner Holder
Exergen TAT-5000 holder and installation instructions
2051186-001
Power accessories
Part
Part description
Part number
Battery - CARESCAPE V100 vital
signs monitor
FRU CARESCAPE V100 vital signs monitor battery (X1 Batt)
2037103-016
12W Power Supply
Power supply, Input 100-240VAC 50/60 Hz 0.5A;
Output 12VDC 1.0A
2018859-001
12W Power Supply (Japan)
Power supply, Input 100-240VAC 50/60 Hz 0.5A;
Output 12VDC 1.0A
2018859-004
Power Cord (Japan)
Power supply cord, Japan ST-ST PSE 10A 250V 12 FT
405535-014
Power Cord (US)
Power supply cord, hospital grade 10A 125V 12FT
405535-002
Power Cord (Brazil)
Power supply cord, Brazil ST- ST 10A 250V 2.5M.
401855-041
Power Cord (continental Europe
and Korea)
Power supply cord, continental Europe 10A 250V 2.5M
401855-101
Power Cord (UK)
Power supply cord, British 10A 250V 2.5M
401855-102
Power Cord (Italy)
Power supply cord, Italian 10A 250V 2.5M
401855-103
Power Cord (Australia)
Power supply cord, Australian 10A 250V 2.5M
401855-110
Power Cord (India)
Power supply cord, Indian 10A 250V 2.5M
401855-108
Printer accessories
Part
Replacement Paper
2048723-002D
Part description
Printer paper roll - 10/box
CARESCAPE V100 Vital Signs Monitor
Part number
089100
6-13
Parts lists and drawings: Compatible service parts
Mounting accessories
Part
Part description
Part number
Roll Stand
Rollstand, CARESCAPE, GCX Version
2033297-001
Pole Mount
Pole Mount
2009762-001
Power Supply Mounting Bracket
12W Power supply roll stand bracket
2047870-001
Wall Mount Bracket
GCX wall mount bracket for DP100 - 400 monitors
CR-0008-01
IR adapter cable roll mount bracket
IR adapter cable roll mount bracket
2025344-001
Connectivity accessories
Part
Part description
Part number
ILC1931
DINALINK ApexPro Adapter
001931
ILC1926
Isolated Line Converter
001926
ILC1932
DINALINK ApexPro FH adapter
001932
Cable Assy, use with 001932
Cable assembly to use with 001932
394119-008
Cable Assy, use with 001931
Cable assembly telemetry interface DINALINK
418497-002
Cable Assy, use with 001926,
001931, 001932
Cable assembly, DINAMAP to ILC
683235
Cable Assy
Cable assembly, ILC to PC
683242
Cable Kit, USB
USB cable kit, DINAMAP to PC
2040229-001
Patient ID
Patient ID IR Cable (used with IR adapter kit)
2024500-001
Patient ID Kit
IR adapter kit with bracket
2026273-002
Remote Alarm
Remote Alarm Cable
487208CR
6-14
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
Field-replaceable units (FRUs)
NOTE
GE supports troubleshooting and repair to the FRU-level only. GE does not
make available schematics, assembly drawings, or bills of material beyond
what is provided in this manual. Attempting repair on a PCB or factorysealed component is not recommended.
FRU list
The following table offers details of each of the corresponding bubble numbers
that appear on the exploded engineering-assembly drawing (drawing is located
after this table). Photos of each FRU follow.
NOTE
FRU numbers are subject to change.
Bubble Number
Part Number
2
2037103-002
FRU CARESCAPE Plastic Kit No PRTR
3
2037103-003
FRU CARESCAPE Plastic Kit W/ PRTR
4
2037103-004
FRU CARESCAPE V100 TEMPERATURE KIT
5
2037103-005
FRU CARESCAPE V100 Printer Assembly
6a
2037103-006
FRU CARESCAPE V100 BZL, (BP ONLY)
7
2037103-007
FRU CARESCAPE V100 Inner chassis kit
8
2037103-008
FRU CARESCAPE V100 PRTR DOORX1/ROLLERS X5
10b, h
2037103-083
FRU CARESCAPE V100 V1.5 Main Board
10b, j
2037103-087
FRU CARESCAPE V100 V1.5 Main Board MS-2011
12c
2037103-012
FRU CARESCAPE V100 UI Board
13
2037103-013
FRU CARESCAPE V100 SpO2 NELLCOR
15d
2037103-015
FRU CARESCAPE V100 Pneumatic Kit
16e
2037103-016
FRU CARESCAPE V100 BATTERY (X1 BATT)
17
2037103-017
FRU CARESCAPE V100 Speaker
18
2037103-018
FRU CARESCAPE V100 Cable kit
19f
2037103-062
FRU CARESCAPE V100 Fascia Kit - English
19f
2037103-063
FRU CARESCAPE V100 Fascia Kit - German
19f
2037103-064
FRU CARESCAPE V100 Fascia Kit - Czech
19f
2037103-065
FRU CARESCAPE V100 Fascia Kit - Danish
2048723-002D
Description
CARESCAPE V100 Vital Signs Monitor
6-15
Parts lists and drawings: Field-replaceable units (FRUs)
Bubble Number
Part Number
19f
2037103-066
FRU CARESCAPE V100 Fascia Kit - Dutch
19f
2037103-067
FRU CARESCAPE V100 Fascia Kit - Finnish
19f
2037103-068
FRU CARESCAPE V100 Fascia Kit - French
19f
2037103-069
FRU CARESCAPE V100 Fascia Kit - Greek
19f
2037103-070
FRU CARESCAPE V100 Fascia Kit - Hungarian
19f
2037103-071
FRU CARESCAPE V100 Fascia Kit - Italian
19f
2037103-072
FRU CARESCAPE V100 Fascia Kit - Japanese
19f
2037103-073
FRU CARESCAPE V100 Fascia Kit - Korean
19f
2037103-074
FRU CARESCAPE V100 Fascia Kit - Norwegian
19f
2037103-075
FRU CARESCAPE V100 Fascia Kit - Polish
19f
2037103-076
FRU CARESCAPE V100 Fascia Kit - Portuguese
19f
2037103-077
FRU CARESCAPE V100 Fascia Kit - Russian
19f
2037103-078
FRU CARESCAPE V100 Fascia Kit - Slovak
19f
2037103-079
FRU CARESCAPE V100 Fascia Kit - Spanish
19f
2037103-080
FRU CARESCAPE V100 Fascia Kit - Swedish
19f
2037103-081
FRU CARESCAPE V100 Fascia Kit - Lithuanian
19f
2037103-082
FRU CARESCAPE V100 Fascia Kit - Turkish
22
2037103-022
FRU CARESCAPE V100 ALL HARDWARE KIT
23h
2037103-023
FRU CARESCAPE V100 SpO2 MASIMO
23 j
2037103-084
FRU CARESCAPE V100 SpO2 MASIMO MS-2011
24
2037103-024
FRU CARESCAPE V100 SpO2 OHMEDA
44g
2037103-044
FRU CARESCAPE V100 Keypad Kit
52a
2037103-052
FRU CARESCAPE V100 BZL, (BP & TEMP)
53a, h
2037103-053
FRU CARESCAPE V100 BZL, (BP & SpO2)
53a, j
2037103-085
FRU CARESCAPE V100 BZL, (BP & SpO2) MS-2011
54a, h
2037103-054
FRU CARESCAPE V100 BZL, (BP & SpO2 & TEMP)
6-16
Description
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
a
Bubble Number
Part Number
54a, j
2037103-086
Description
FRU CARESCAPE V100 BZL, (BP & SpO2 & TEMP) MS-2011
All SpO2 technology labels included. Select applicable label per monitor configuration.
b
Main boards configured with SuperSTAT NIBP algorithm, Nellcor SpO2, and Temperature enabled. Reconfigure as applicable per monitor
configuration. Refer to “Installation” Chapter 3 for more details.
c
All UI board LEDs installed. Cover LEDs with applicable fascia per monitor configuration.
d
Check valve has directional arrow indicating correct orientation for assembly.
e
Fully charge battery before initial use. Refer to “Installation” Chapter 3 for more details.
f
Kit includes all versions of fascia and display covers. Install per monitor configuration.
g
Remove Print button for non-printer versions of monitor. Refer to following assembly drawings.
h This
j This
part number is compatible with product code SDT only. Refer to “Equipment ID” on page 1-13 to determine product code.
part number is compatible with product code SH6 only. Refer to “Equipment ID” on page 1-13 to determine product code.
FRU photos
FRU 2037103-002: CARESCAPE plastic kit no printer
FRU 2037103-003: CARESCAPE plastic kit w/ printer
NOTE
Rear case with printer shown.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-17
Parts lists and drawings: Field-replaceable units (FRUs)
FRU 2037103-004: CARESCAPE V100 temperature kit (Alaris)
6-18
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
FRU 2037103-005: CARESCAPE V100 printer assembly
FRU 2037103-006: CARESCAPE V100 BZL, (BP only)
FRU 2037103-052: CARESCAPE V100 BZL, (BP & Temp)
FRU 2037103-053: CARESCAPE V100 BZL, (BP & SpO2)
FRU 2037103-054: CARESCAPE V100 BZL, (BP & SpO2 & Temp)
NOTE
Kit includes only 1 bezel.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-19
Parts lists and drawings: Field-replaceable units (FRUs)
FRU 2037103-007: CARESCAPE V100 inner chassis kit
NOTE
Kit includes 4 adhesive-backed feet.
FRU 2037103-008: CARESCAPE V100 Prtr door X1/rollers X5
NOTE
Kit includes 1 printer door with label and 5 printer rollers.
6-20
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
FRU 2037103-083: CARESCAPE V100 V1.5 main board
NOTE

Each main board comes with all parameters installed. For
monitors that do not include specific options (Printer, SpO2,
Temperature), these options must be turned off while the
monitor is in configuration mode.

Each main board comes configured with the SuperSTAT NIBP
algorithm. If your monitor was originally configured with the
Auscultatory or Classic NIBP Algorithm, the algorithm must be
changed while the monitor is in configuration mode.
FRU 2037103-012: CARESCAPE V100 UI board
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-21
Parts lists and drawings: Field-replaceable units (FRUs)
Masimo (MS-11)
Masimo (MS-2011)
Nellcor
Ohmeda
FRU 2037103-013: CARESCAPE V100 SpO2 Nellcor
FRU 2037103-023: CARESCAPE V100 SpO2 Masimo
or FRU 2037103-084 CARESCAPE V100 SpO2 Masimo MS-2011
FRU 2037103-024: CARESCAPE V100 SpO2 Ohmeda
NOTE

All 4 SpO2 boards shown. Kit includes only one.

Nellcor hardware shown. Kit includes matching hardware.
FRU 2037103-015: CARESCAPE V100 pneumatic kit
6-22
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
FRU 2037103-016: CARESCAPE V100 main battery (X1 BATT)
FRU 2037103-017: CARESCAPE V100 speaker
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-23
Parts lists and drawings: Field-replaceable units (FRUs)
FRU 2037103-018: CARESCAPE V100 cable kit
FRU number
6-24
Description
Language
FRU 2037103-062
CARESCAPE V100 Fascia Kit
English
FRU 2037103-063
CARESCAPE V100 Fascia Kit
German
FRU 2037103-064
CARESCAPE V100 Fascia Kit
Czech
FRU 2037103-065
CARESCAPE V100 Fascia Kit
Danish
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
FRU number
2048723-002D
Description
Language
FRU 2037103-066
CARESCAPE V100 Fascia Kit
Dutch
FRU 2037103-067
CARESCAPE V100 Fascia Kit
Finnish
FRU 2037103-068
CARESCAPE V100 Fascia Kit
French
FRU 2037103-069
CARESCAPE V100 Fascia Kit
Greek
FRU 2037103-070
CARESCAPE V100 Fascia Kit
Hungarian
FRU 2037103-071
CARESCAPE V100 Fascia Kit
Italian
FRU 2037103-072
CARESCAPE V100 Fascia Kit
Japanese
FRU 2037103-073
CARESCAPE V100 Fascia Kit
Korean
FRU 2037103-074
CARESCAPE V100 Fascia Kit
Norwegian
FRU 2037103-075
CARESCAPE V100 Fascia Kit
Polish
FRU 2037103-076
CARESCAPE V100 Fascia Kit
Portuguese
FRU 2037103-077
CARESCAPE V100 Fascia Kit
Russian
FRU 2037103-078
CARESCAPE V100 Fascia Kit
Slovak
FRU 2037103-079
CARESCAPE V100 Fascia Kit
Spanish
FRU 2037103-080
CARESCAPE V100 Fascia Kit
Swedish
FRU 2037103-081
CARESCAPE V100 Fascia Kit
Lithuanian
FRU 2037103-082
CARESCAPE V100 Fascia Kit
Turkish
CARESCAPE V100 Vital Signs Monitor
6-25
Parts lists and drawings: Field-replaceable units (FRUs)
1
2
19
3
4
20
13
5
6
14
21
15
7
16
8
10
9
17
11
12
22
18
FRU 2037103-022: CARESCAPE V100 all hardware kit
NOTE
Each Hardware kit includes the following:
Item
6-26
Description
Torque
specifications
Qty
1
Cable Tie, Locking, Nylon 6.6, 3.1" X 0.09”
5
2
Tie Wrap Intermediate, 2”
10
3
Screw, Mach Pnhd 832 X 2-1/2 SS
Vibratite
8 in-lb ± 0.5 in-lb
6
4
Screw, No6, Torx Pan, 1.0 Inch Vib
8 in-lb ± 0.5 in-lb
4
5
Screw, No8, Pozi-Pan 0.75 in Vib
8 in-lb ± 0.5 in-lb
20
6
Screw, M3 X 12, Self-Tap, Torx
6 in-lb ± 0.5 in-lb
20
7
Screw, Self Tap,Torx, Zinc
6 in-lb ± 0.5 in-lb
23
8
Kit, Screwlock Female With Thread-Lock
6 in-lb ± 0.5 in-lb
3
9
Screw, Mach Pnhd Phil 440 X 3/16 SS
Vibratite
3 in-lb ± 0.5 in-lb
20
10
Standoff Masimo SpO2
4
11
Standoff Nellcor SpO2
4
12
Standoff Ohmeda SpO2
4
13
Wshr, #10 Fender Washer 1.00" OD
Stainle
4
14
Spacer, Steel Zinc
20
15
Foot, Rnd, 12.7 Dia X 3.5 H Self Adhsv
20
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
Item
Description
Torque
specifications
Qty
16
Tubing Silicone 1/8 ID X 1/4 OD
1 foot
17
Tubing Silicone Clear 3/32” ID 7/32” OD
1 foot
18
Conn Plastic Tee
4
19
Speaker Clamp Ring
3
20
Adhesive Backed Cable Tie Mount, 0.75 X
0.75
5
21
Extrusion Grommet, handle
3
22
Filter 40 Micron
10
FRU 2037103-044: CARESCAPE V100 keypad kit
NOTE
Printer version shown. For non-printer versions, the print key will
need to be trimmed before installation. See parts drawing on page
6-29 for further details.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-27
Parts lists and drawings: Field-replaceable units (FRUs)
FRU main reference guide drawing
For quick reference use the following FRU main reference guide drawing.
6-28
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-29
Parts lists and drawings: Field-replaceable units (FRUs)
6-30
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-31
Parts lists and drawings: Field-replaceable units (FRUs)
6-32
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-33
Parts lists and drawings: Field-replaceable units (FRUs)
6-34
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Field-replaceable units (FRUs)
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-35
Parts lists and drawings: Disassembly/reassembly of FRUs
Disassembly/reassembly of FRUs
Electrostatic discharge (ESD) precautions
All external connectors of the monitor are designed with protection from ESD
damage. However if the monitor requires service, exposed components and
assemblies inside are susceptible to ESD damage. This includes human hands,
non-ESD protected work stations or improperly grounded test equipment.
The following guidelines may not guarantee a 100% static-free workstation, but
can greatly reduce the potential for failure of any electronic assemblies being
serviced:
6-36

Discharge any static charge you may have built up before handling
assemblies containing semiconductors.

A grounded, antistatic wristband (3M part number 2046 or equivalent) or
heel strap should be worn at all times while handling or repairing
assemblies containing semiconductors.

Use properly grounded soldering and test equipment.

Use a static-free work surface (3M part number 8210 or equivalent) while
handling or working on assemblies containing semiconductors.

Do not remove assemblies from antistatic containers (Velo-stat bags) until
absolutely necessary.

Make sure power to an assembly is turned off before removal.

Do not slide electrical/electronic assemblies across any surface.

Do not touch semiconductor leads unless absolutely necessary.

Electronic assemblies should be stored only in antistatic bags or boxes.

Handle all PCB assemblies by their edges.

Do not flex or twist a circuit board.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Disassembly/reassembly of FRUs
Monitor fascia replacement procedure
2048723-002D
1.
Pry open the front face plate at the upper corners and remove the face
plate.
2.
Remove the existing fascia.
3.
Remove the tab at the top of the new fascia that includes the part number.
CARESCAPE V100 Vital Signs Monitor
6-37
Parts lists and drawings: Disassembly/reassembly of FRUs
6-38
4.
Turn the fascia over and remove the protective liner from the three pieces of
double-sided adhesive tape.
5.
Turn the fascia right side up and align the fascia with the bottom notch on
the monitor.
6.
Press the fascia onto the monitor.
7.
Tuck the top part of the fascia under the top notch on the monitor.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Disassembly/reassembly of FRUs
8.
Place the tabs on the bottom edge of the face plate into the slots on the
monitor.
9.
Snap the face plate back on the monitor.
Monitor disassembly procedure
The following procedure is sequential (i.e., you must remove the main battery
and rear case to remove the printer, etc.).
CAUTION
Internal electronic components are susceptible to damage by
electrostatic discharge. To avoid damage when disassembling
the monitor, observe the standard precautions and procedures
for handling static-sensitive components.
Main battery
2048723-002D
1.
Remove 4 screws securing the instruction cards.
2.
Remove the battery compartment door and adhesive pad.
CARESCAPE V100 Vital Signs Monitor
6-39
Parts lists and drawings: Disassembly/reassembly of FRUs
3.
The battery can now be removed.
1.
Remove remaining two screws from the bottom of the monitor.
2.
Set monitor upright.
3.
Carefully remove the front faceplate.
4.
Remove 2 screws behind black overlay.
5.
Set monitor on its face and open the printer door.
6.
Carefully remove the rear case.
Rear case
6-40
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Disassembly/reassembly of FRUs
7.
Unplug speaker cable and temperature module cable (if installed) from
circuit board.
1.
Lift the 2 black tabs and remove printer cable.
2.
Remove printer assembly.
3.
Unplug air hose from valve and filter.
4.
Remove remaining 3 cable assemblies.
5.
Locate and release retention tab and slide back sub chassis.
Printer
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-41
Parts lists and drawings: Disassembly/reassembly of FRUs
6.
Remove sub-chassis and set aside.
7.
Remove pneumatic assembly from sub-chassis.
1.
Remove 2 screws securing SpO2 board.
SpO2 board
Threaded standoffs have screws on both ends.
2.
Remove SpO2 board.
1.
Remove 2 SpO2 connector screws.
2.
Unplug 2 pneumatic hoses from bezel.
3.
Remove 4 torx-head screws along the bottom of main board.
4.
Lift unit and remove bezel.
Front bezel
6-42
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Disassembly/reassembly of FRUs
Main board
1.
Remove 9 torx-head screws.
1.
Carefully lift the Main board away from the UI board.
2.
Collect the 5 spacers used to align the Main and UI board.
3.
Lift the UI board away from the front panel.
4.
The monitor is now completely disassembled.
5.
Reverse the above sequence to reassemble the monitor.
6.
Be careful not to pinch any cables or tubing during reassembly.
Display board
NOTE
Updated Instructions may be included in your replacement parts kit. Always
2048723-002D
CARESCAPE V100 Vital Signs Monitor
6-43
Parts lists and drawings: Disassembly/reassembly of FRUs
review all material included in your kit.
Exergen TAT
Cable replacement
6-44
1.
Turn off the monitor and unplug the cable from the host communication
port on the back of the monitor.
2.
On the back of the scanner, loosen the single screw at the bottom.
3.
Remove the battery door.
4.
Remove the cable.
5.
Install the replacement cable. Making sure both keyways line up, install male
connector completely into the female jack inside the scanner.
6.
Tighten the battery screw.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Parts lists and drawings: Disassembly/reassembly of FRUs
7.
2048723-002D
Screw the cable connector jack to the host communication port on the back
of the monitor.
CARESCAPE V100 Vital Signs Monitor
6-45
Parts lists and drawings: Disassembly/reassembly of FRUs
For your notes
6-46
CARESCAPE V100 Vital Signs Monitor
2048723-002D
A
2048723-002D
Technical
specifications and
default settings
CARESCAPE V100 Vital Signs Monitor
A-1
Technical specifications and default settings: Specifications
Specifications
General
General specifications
Mechanical
Dimensions
Height
19.5 cm (7.7 in)
Width
21.9 cm (8.6 in) without temperature
25.4 cm (10.0 in) with temperature
Depth
13.5 cm (5.3 in)
Weight (Including battery)
2.4 kg (5.4 lb)
Mountings
Self-supporting on rubber feet, pole mounted, or wall mount bracket
Portability
Carried by recessed handle
Power requirements
Power converter universal
P/N: 2018859-001
Protection against electrical shock
Class II
AC input
100 to 240VAC, 0.5A
DC output voltage
12VDC at 1.0A
The AC mains power adapter contains a nonresettable and
nonreplaceable fuse.
Monitor
Protection against electrical shock
Internally powered or Class II when powered from specified external
power supply.
DC input voltage
12 VDC, supplied from a source conforming to IEC 60601-1.
Fuses
The monitor contains three fuses. The fuses are mounted within the
monitor. The fuses protect the low voltage DC input, the main battery,
and the remote alarm output. The +5 V output on the host port connector
is regulated by internal supply.
Main Battery
Refer to “Battery” on page A-15
Environmental
Operating temperature
+ 5°C to + 40°C (+ 41°F to + 104°F)
Operating atmospheric pressure
500 hPa to 1060 hPa
A-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Specifications
General specifications
Storage/transportation
Storage temperature
– 20°C to + 50°C (– 4°F to + 122°F)
Atmospheric pressure
500 hPa to 1060 hPa
Humidity range
5% to 95% noncondensing
Radio frequency
Complies with IEC Publication 60601-1-2 Medical Electrical Equipment,
Electromagnetic Compatibility Requirements and Tests and CISPR 11
(Group 1, Class B) for radiated and conducted emissions
Printer
Printer specifications
Printer type
Thermal dot array
Resolution
384 dots/inch horizontal
Paper type
The paper roll used by the printer must be compatible with GE PN
770137.
Languages printed
English, German, French, Italian, Spanish, Portuguese, Hungarian, Polish,
Czech, Finnish, Swedish, Danish, Dutch, Norwegian, and Slovak
Languages not printed
(text printed in English only)
Russian, Greek, Korean, Japanese, Turkish and Lithuanian
Alarms
Alarm specifications
Alarm volume
60 dB to 75 dB
Remote alarm
The remote alarm signals an alarm in 0.5 seconds of the monitor’s
display of the alarm.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-3
Technical specifications and default settings: Specifications
NIBP
WARNING
Use only GE CRITIKON blood pressure cuffs. The size, shape,
and bladder characteristics can affect the performance of the
instrument. Inaccurate readings may occur unless GE
CRITIKON blood pressure cuffs are used.
NIBP specifications
Cuff pressure range
(Normal operating range)
0 to 290 mmHg (adult/ped)
0 to 145 mmHg (neonate)
Blood pressure accuracy (Classic and Auscultatory)
Meets ANSI/AAMI standard SP-10 (mean error 5 mmHg,
standard deviation 8 mmHg)
Blood pressure accuracy (SuperSTAT)
Meets ANSI/AAMI standard SP-10 (mean error 5 mmHg,
standard deviation 8 mmHg)
Maximum determination time
120 s (adult/ped)
85 s (neonate)
Overpressure cutoff
300 to 330 mmHg (adult/ped)
150 to 165 mmHg (neonate)
BP range (Classic and Auscultatory)
Systolic
30 to 245 mmHg (adult/ped)
40 to 140 mmHg (neonate)
MAP
15 to 215 mmHg (adult/ped)
30 to 115 mmHg (neonate)
Diastolic
10 to 195 mmHg (adult/ped)
20 to 100 mmHg (neonate)
BP range (SuperSTAT)
Systolic
30 to 290 mmHg (adult/ped)
30 to 140 mmHg (neonate)
MAP
20 to 260 mmHg (adult/ped)
20 to 125 mmHg (neonate)
Diastolic
10 to 220 mmHg (adult/ped)
10 to 110 mmHg (neonate)
Pulse rate range (Classic and Auscultatory)
30 to 200 beats/min (adult/ped)
30 to 220 beats/min (neonate)
Pulse rate range (SuperSTAT)
30 to 240 beats/min (adult/ped)
30 to 240 beats/min (neonate)
Pulse rate accuracy
± 3.5% or 3 bpm, whichever is higher
A-4
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Specifications
Ohmeda SpO2
Ohmeda SpO2 specifications
Measurement range
SpO2
1 to 100%
Pulse rate
30 to 250 bpm
Perfusion Index Value (Plr)
0.00 to 9.99
Accuracy*
Saturation
Adult*
70 to 100% ±2 digits, whichever is greater,
(without motion)
Neonate*
70 to 100% ±3 digits (without motion)
Adult/Neonate**
70 to 100% ±3 digits (during clinical motion)
Low perfusion
70 to 100% ±2 digits (during clinical low
perfusion)
Pulse rate
Adult /Neonate
30 to 250 bpm: ± 2 digits or ± 2%, whichever is
greater, (without motion)
30 to 250 bpm: ± 5 digits (during motion)
Low perfusion
30 to 250 bpm: ± 3 digits
*SpO2 measurement accuracy is based on deep hypoxia studies using OxyTip++ sensors on healthy adult volunteer subjects. Arterial blood
samples were analyzed simultaneously on multiple CO-oximeters. This variation equals plus or minus one standard deviation. Plus or minus one
standard deviation encompasses 68% of the population.
**Applicability: TS-AF sensors.
NOTE
Accuracy may vary for some sensors; always check the instructions for the sensor.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-5
Technical specifications and default settings: Specifications
Specifications: Ohmeda sensor accuracy
SpO2 range
70% to 100%
Sensor model
OxyTip++
TS-F-D
±2 digits without motion
TS-E-D
±3 digits without motion
TS-W-D
±2 digits without motion
TS-SE-3
±2 digits without motion
TS-AF-10
±2 digits without motion
TS-AF-25
±2 digits without motion
TS-F4-GE
±2 digits without motion
TS-F2-GE
±2 digits without motion
TS-E4-GE
±3 digits without motion
TS-E2-GE
±3 digits without motion
Specifications: Ohmeda sensor accuracy
Sensor model
TS-SA4-GE
TS-SA-D
SpO2 range
70% to 100%
±2 digits
SpO2 range
90% to 100%
±1 digits
SpO2 range
80% to 90%
±2 digits
SpO2 range
70% to 80%
±3 digits
SpO2 range
below 70%
unspecified
Specifications: Ohmeda sensor accuracy
Sensor light source
Wavelength*
Infrared: 930 to 950 nm (nominal)
Red 650 to 670 nm (nominal)
Average power
< 1 mW
* Information about wavelength range can be especially useful to clinicians.
A-6
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Specifications
Nellcor SpO2
WARNING
Nellcor-labeled monitors are only compatible with Nellcor
Oximax sensors and cables.
Nellcor SpO2 specifications
Measurement range
SpO2
1 to 100%
Pulse rate
20 to 250 bpm
Perfusion range
0.03 to 20%
Accuracy
Saturation
Adult*
70 to 100% ±2 digits
Neonate*
70 to 100% ±3 digits
Low perfusion**
70 to 100% ±2 digits
Pulse Rate
Adult and neonate
20 to 250 bpm ±3 digits
Low perfusion**
20 to 250 bpm ±3 digits
*Adult specifications are shown for OxiMax MAX-A and MAX-N sensors with the N-600. Saturation accuracy will vary by sensor type. This variation
equals plus or minus one standard deviation. Plus or minus one standard deviation encompasses 68% of the population. Accuracy is based on deep
hypoxia studies on healthy adult volunteer subjects. Arterial blood samples were analyzed simultaneously on multiple CO-oximeters.
**Applicability: OxiMax MAX-A, MAX-AL, MAX-P, MAX-I, and MAX-N sensors.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-7
Technical specifications and default settings: Specifications
Specifications: Nellcor sensor accuracy
NOTE
All Nellcor OXIMAX sensors must be used with the NELL cable; the SCP-10 cable. RS-10 and Oxisensor II sensors are
not compatible with the CARESCAPE V100 vital signs monitor.
SpO2 range
70% to 100%
Sensor model
OXIMAX
MAX-A, MAX-AL
± 2 digits
MAX-N (adult)
± 2 digits
MAX-N* (neonate)
± 3 digits
MAX-P
± 2 digits
MAX-I
± 2 digits
MAX-FAST
± 2 digits
SC-A (adult)
± 2 digits
SC-PR (neonate)
± 3 digits
SC-NEO
± 3 digits
MAX-R**
± 3.5 digits
OxiCliq
OxiCliq A
± 2.5 digits
OxiCliq P
± 2.5 digits
OxiCliq N (adult)
± 2.5 digits
OxiCliq N* (neonate)
± 3.5 digits
OxiCliq I
± 2.5 digits
Reusable sensor models
D-YS (infant to adult)
± 3 digits
D-YS (neonate)
± 4 digits
A-8
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Specifications
Specifications: Nellcor sensor accuracy
D-YS & D-YSE
± 3.5 digits
D-YS & D-YSPD
± 3.5 digits
DS-100A
± 3 digits
OXI-A/N (adult)
± 3 digits
OXI-A/N (neonate)
± 4 digits
OXI-P/I
± 3 digits
Neonatal sensor accuracy
When sensors are used on neonatal subjects as
recommended, the specified accuracy range is increased
by ±1 digit, as compared to adult usage, to account for the
theoretical effect on oximeter measurements of fetal
hemoglobin in neonatal blood. For example, MAX-N
accuracy on neonates is ±3 digits, rather than ±2 digits.
Sensor light source
Wavelength***
Infrared: 890 nm (nominal)
Red: 660 nm (nominal)
Power dissipation
Infrared: 22.5 mW (max)
Red: 30 mW (max)
*
The MAX-N, D-YS, OXI-A/N, and OxiCliq N were tested on patients >40 kg.
**
The accuracy specification has been determined between saturations of 80%-100%.
*** Information about wavelength range can be especially useful to clinicians.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-9
Technical specifications and default settings: Specifications
Masimo SpO2
WARNING
Use only Masimo oximetry sensor for SpO2 measurements.
Other oxygen transducers (sensors) may cause improper SpO2
performance.
WARNING
Monitors identified as having Masimo SET technology are
compatible only with Masimo SET sensors and cables.
Masimo SpO2 specifications
Measurement range
SpO2
1 to 100%
Pulse rate
25 to 240 bpm
Perfusion range
0.02 to 20%
Accuracy and motion tolerance
Saturation
Without motion - adult/pediatric*
70 to 100% ± 2 digits
Without motion - neonate*
70 to 100% ± 3 digits
With motion - adult/pediatric/neo**†
70 to 100% ± 3 digits
Low perfusion‡
70 to 100% ± 2 digits
0 to 69% unspecified
Pulse rate
Without motion
25 to 240 bpm ±3 digits
With motion
normal physiologic range
25 to 240 bpm ±5 digits
* The Masimo SET SpO2 parameter with LNOP-Adt sensors has been validated for no motion accuracy in human blood studies on healthy adult
volunteers in induced hypoxia studies in the range of 70-100% SpO2 against a laboratory CO-oximeter and ECG monitor. This variation equals plus
or minus one standard deviation. Plus or minus one standard deviation encompasses 68% of the population.
**The Masimo SET SpO2 parameter with LNOP-Adt sensors has been validated for motion accuracy in human blood studies on healthy adult volunteers
in induced hypoxia studies while performing rubbing and tapping motions at 2 to 4 Hz at an amplitude of 1 to 2 cm and a nonrepetitive motion between
1 to 5 Hz at an amplitude of 2 to 3 cm in induced hypoxia studies in the range of 70-100% SpO2 against a laboratory CO-oximeter and ECG monitor. This
variation equals plus or minus one standard deviation. Plus or minus one standard deviation encompasses 68% of the population.
†The Masimo SET SpO2 parameter with LNOP-Neo Pt sensors has been validated for neonatal motion accuracy in human blood studies on neonates
while moving the neonate’s foot at 2 to 4 cm against a laboratory CO-oximeter and ECG monitor. This variation equals plus or minus one standard
deviation. Plus or minus one standard deviation encompasses 68% of the population.
‡The Masimo SET SpO2 parameter has been validated for low perfusion accuracy in bench-top testing against a Biotek Index 2 simulator and
Masimo’s simulator with signal strengths of greater than 0.02% and a % transmission of greater than 5% for saturations ranging from 70 to 100%.
This variation equals plus or minus one standard deviation. Plus or minus one standard deviation encompasses 68% of the population.
A-10
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Specifications
Specifications: Masimo sensor accuracy
SpO2 range
70% to 100%
Sensor model
LNOP
LNOP ADT
± 2 digits without motion
LNOP NEO
± 3 digits without motion
LNOP NEO-L
Foot
Finger
± 3 digits without motion
± 2 digits without motion
LNOP NEO PT-L
± 3 digits without motion
LNOP Adtx
± 2 digits without motion
LNOP Pdtx
± 2 digits without motion
LNOP DCI
± 2 digits without motion
LNOP DCIP
± 2 digits without motion
LNOP Hi Fi-Neo/adult
Foot
Finger
± 3 digits without motion
± 2 digits without motion
LNOP Hi Fi-Infant/Ped
± 2 digits
LNOP Blue Infant Thumb/Toe*
± 3 digits (for 80-100) without motion
± 4 digits (for 60-80) without motion
± 3.3 digits (for 70-100) without motion
LNOP YI Multi-Site
Foot/hand
Finger/toe
± 3 digits without motion
± 2 digits without motion
LNOP DC-195
± 2 digits without motion
LNOP TC-I
± 3.5 digits without motion
LNCS TCI
± 3.5 digits without motion
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-11
Technical specifications and default settings: Specifications
Specifications: Masimo sensor accuracy
LNCS DC-I
± 2 digits without motion
LNCS DC-IP
± 2 digits without motion
LNCS Adult Adtx
± 2 digits without motion
LNCS Ped Pdtx
± 2 digits without motion
LNCS Infant-L
± 2 digits without motion
LNCS Neo PT-L
± 3 digits without motion
Resolution
Saturation (% SpO2)
1%
Pulse rate (bpm)
1
Low perfusion performance
0.02% Pulse amplitude
and % transmission >5%
Saturation (% SpO2) ±2 digits
Pulse rate ±3 digits
Interfering substances
Carboxyhemoglobin may erroneously increase
readings. The level of increase is approximately
equal to the amount of carboxyhemoglobin
present. Dyes, or any substance containing dyes,
that change usual arterial pigmentation may
cause erroneous readings.
Sensor light source
Wavelength**
Infrared: 905 nm (nominal)
Red: 660 nm (nominal)
Power dissipation
Infrared: 22.5 mW (max)
Red: 27.5 mW(max)
*Masimo SET Technology with LNOP Blue sensors have been validated for no motion accuracy in human blood studies on neonatal, infant, and
pediatric patients with congenital, cyanotic cardiac lesions in the range of 60% to 100% SpO2 against a laboratory CO-oximeter. This variation
equals plus or minus one standard deviation, which encompasses 68% of the population.
** Information about wavelength range can be especially useful to clinicians.
A-12
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Specifications
Temperature
WARNING
Alaris: Use only recommended probes and probe covers. The
size, shape, and thermal characteristics of the probe covers
can affect the performance of the instrument. Inaccurate
readings may occur unless recommended probes and probe
covers are used. Visually inspect the probe prior to use to be
sure it is defect free. Please refer to the Accessories list
provided with your monitor.
Temperature specifications
Units of measure
°Fahrenheit (F) or °Celsius (C)
Range
Alaris
Predictive Mode
Turbo Temp
Max: 41.1°C; 106.0°F
Min: 35.6°C; 96.0°F
Tri-Site
Max: 41.1°C; 106.0°F
Min: 35.0°C; 95.0°F
Monitor Mode
Turbo Temp
Max: 42.1°C; 107.9°F
Min: 26.7°C; 80.0°F
Tri-Site
Max: 42.1°C; 107.9°F
Min: 26.7°C; 80.0°F
Turbo Temp and Tri-Site
Continuous (monitor) mode accuracy
±0.1°C; ±0.2°F
when tested in a calibrated liquid bath;
meets ASTM E1112, Table 1, in range
specified
NOTE:
If large changes occur in the ambient
temperature, the temperature system
can be recalibrated by cycling the
monitor’s power using the On/Off
button.
Determination time
2048723-002D
Turbo Temp
Oral or rectal
As fast as 7 seconds
Tri-Site
Oral
Rectal
Axillary
As fast as 12 seconds
As fast as 11 seconds
As fast as 13 seconds
CARESCAPE V100 Vital Signs Monitor
A-13
Technical specifications and default settings: Specifications
Temperature specifications
Exergen
Measurement Mode
Accuracy
Max: 43°C; 110°F
Min: 16°C; 61°F
±0.1°C; ±0.2°F
meets EN 12470-5
Predictive Mode
Not applicable
Monitor Mode
Not applicable
Operating environment
16° to 40°C; 60° to 104°F (ambient)
Arterial head balance range for body
temperature*
34.5° to 43°C; 94° to 110°F
Resolution
0.1°C or 0.1°F
Response time
approx. 0.04 seconds, typical
* Automatically applied when temperature is within normal body temperature range, otherwise reads surface temperature.
A-14
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Specifications
Battery
Monitor - main battery
Battery specifications
Capacity
Battery life
6V; 3.3 Ahr sealed lead-acid battery
5 hours with SpO2 technology with a usage scenario of:
NIBP determinations every 5 minutes with adult cuff
 Printout after every determination
 SpO2 parameter active at 60 bpm
 Temperature parameter active in monitor mode

Up to 11.5 hours without SpO2 technology with a usage scenario of:
NIBP determinations every 15 minutes
 Temperature parameter active

Charge time
Approx. 5 hours from full discharge when the monitor is off
Approx. 8 hours when the monitor on
Exergen temporal scanner
Battery specifications
Capacity
(1) 9V alkaline
Battery life
Approx. 15,000 readings
(When scanning for 5 seconds and reading the temperature display for
2 seconds before turning thermometer off.)
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-15
Technical specifications and default settings: Default settings
Default settings
Alarms
The factory default for alarm volume is 5.
NIBP
Adult/ped
Neonate
Nonpatient
specific
Systolic (mmHg)
HIGH
200
100
LOW
80
40
HIGH
120
60
LOW
30
20
Inflation pressure
(for Auscultatory)
160
100
Inflation pressure
(for SuperSTAT)
135
100
Inflation pressure (for Classic)
160
110
Diastolic (mmHg)
Cycle button default
15 min
Ohmeda SpO2
A-16
SpO2 (%) HIGH alarm limit
100
SpO2 (%) LOW alarm limit
90
Line frequency mode
60 (for 60 Hz)
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Technical specifications and default settings: Default settings
Nellcor SpO2
SpO2 (%) HIGH alarm limit
100
SpO2 (%) LOW alarm limit
90
Response mode
1
(for Mode 1: Normal response)
SatSeconds
0
SpO2 (%) HIGH alarm limit
100
SpO2 (%) LOW alarm limit
90
Averaging time
12 seconds
FastSAT mode
0 (for Off)
Sensitivity mode
2 (for Low Perfusion)
HIGH alarm limit
150 bpm
LOW alarm limit
50 bpm
Alarm volume
5
Unit of measure
°F
Temperature display time
2 minutes
Masimo SpO2
Pulse rate
Temperature
Alaris
2048723-002D
CARESCAPE V100 Vital Signs Monitor
A-17
Technical specifications and default settings: Default settings
Exergen
A-18
Unit of measure
°F or °C
Defined by Exergen scanner
purchased.
Temperature display time
2 minutes
CARESCAPE V100 Vital Signs Monitor
2048723-002D
B
2048723-002D
Appropriate use of
NIBP simulators
CARESCAPE V100 Vital Signs Monitor
B-1
Appropriate use of NIBP simulators: Appropriate use of NIBP simulators
Appropriate use of NIBP simulators
NIBP accuracy
Noninvasive Blood Pressure (NIBP) monitors are cleared for sale in the U.S. by the
FDA (1) and in Europe through the CE Mark. Both of these processes require that
the accuracy of NIBP monitors be established through clinical testing - the use of
NIBP simulators is not acceptable.
GE Healthcare has established accuracy using the AAMI SP-10 standard (2) and
a similar standard exists in Europe (3). The AAMI standard specifies that the
accuracy of NIBP monitors can be determined using either an invasive (intraarterial) or noninvasive (auscultatory) blood pressure reference. Over the last 30
years, DINAMAP® accuracy has been established using an invasive central
aortic blood pressure reference. More recently, the CARESCAPE V100 vital signs
monitor has also been validated against a manual auscultatory reference.
Clinical vs. simulator readings
There are a number of reasons why the clinical studies are required for the
measurement of NIBP accuracy. Many physiologic measurements (e.g., ECG, HR,
eTCO2) can be taken with little interaction between the monitor and the patient.
These devices can typically be validated using previously recorded patient data.
Unlike the transducers/electrodes used in these devices, the NIBP cuff has two
functions. In addition to sensing the pressure pulses in the cuff, the cuff occludes
and then releases the patient's artery to create the conditions that allow blood
pressure to be measured.
An "artificial arm" would need to test both the sensing and occluding functions of
the cuff, and mimic the nonlinear dynamics of the artery to provide an effective
clinical simulation. While this has been attempted (4), there are no effective
"arms" available.
Commercial NIBP simulators do attempt to test both functions of the NIBP cuff.
Pressure signals are generated by the simulator in response to the inflation and
deflation cycles of the monitor. While the cuff may be in the system, it is
wrapped on a mandrel. The ability of the cuff to transducer pressure signals or
to occlude the artery is not tested.
There are further limitations to the pressure pulses used by simulators. During
the deflation of the cuff, the shape of the generated pressure oscillations
changes as the cuff goes from systolic to diastolic pressures. This is due to the
fact that the artery is only open when the arterial pressure is above cuff
pressure. As can be seen in Figures 1A-1C, the shape of the oscillation changes
as the cuff pressure changes, and the artery opens. Commercial NIBP simulators
use one waveform shape at all pressure levels, which is simply scaled to reflect
the oscillometric envelope.
In addition, the shape of the oscillation generated by commercial simulators
does not match the shape of a typical oscillation measured during clinical
testing (Figures 2A-2B). These differences in the shape of the pulses can effect
B-2
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Appropriate use of NIBP simulators: Appropriate use of NIBP simulators
how an NIBP monitor analyzes the oscillometric envelope. While it is possible to
develop an algorithm, which produces readings that correspond to the simulator
settings, it is preferable to use the clinical data for algorithm development.
What do simulator manufacturers say?
The DNI Nevada (Fluke Biomedical) CuffLink manual states:
"Since the CuffLink produces the same response independent of the inflate/
deflate cycle or the algorithm used by the monitor, we offer the term "Target
Value" as an approximation of the patient's actual blood pressure" (5)
2048723-002D
CARESCAPE V100 Vital Signs Monitor
B-3
Appropriate use of NIBP simulators: Appropriate use of NIBP simulators
BioTek® NIBP Pump 2™ (Fluke Biomedical) manual, in response to the question
of why monitor readings differ from the target values on the simulator, states:
"Neither the monitor or the NIBP Pump 2 is broken. Some monitors were
designed to give readings close to those obtained by the Auscultatory method of
blood pressure determinations. Other monitors have been designed to agree
with Invasive blood pressure readings. It is well known that Invasive and
Auscultatory NIBP readings on the same subject can be quite different" (6)
Both of these statements indicate that these simulators cannot be used to
demonstrate the accuracy of an NIBP monitor.
Why use simulators?
Simulators provide a method for producing repeatable signals that can be used
to check that the monitor is responding to noninvasive blood pressure signals.
Reference values obtained from a particular make and model of an NIBP
monitor can be used to confirm that no changes have occurred after service to
that same type of monitor.
Simulators can also be used to test for leaks and conduct static pressure
calibration of NIBP monitors and as part of preventive maintenance programs.
Summary
The accuracy of an NIBP monitor can only be determined by comparison to a
clinical blood pressure reference. NIBP simulators are useful for certain types of
testing, but should not be used for accuracy testing.
Figure 2A: Cuff oscillation from a clinical measurement
B-4
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Appropriate use of NIBP simulators: Appropriate use of NIBP simulators
Figure 2B: Cuff Oscillation From A Simulator Measurement
References
2048723-002D
1.
FDA, CDRH, Non-Invasive Blood Pressure (NIBP) Monitor Guidance, March 10,
1997
2.
ANSI/AAMI SP10:2002, Manual, Electronic or Automated
Sphygmomanometers
3.
EN 1060-4 2004 Specification for non-invasive sphygmomanometers - Part
4: Test procedures to determine the overall system accuracy of automated
non-invasive sphygmomanometers
4.
Mieke, S, Substitute of simulators for human subjects; Blood Press Monit,
October 1, 1997; 2(5): 251-256
5.
DNI Nevada CuffLink Non-Invasive Blood Pressure Analyzer, Operating and
Service Manual; Revision E, 11/97
6.
NIBP Pump 2 Noninvasive Blood Pressure Simulator and Tester, Operations
Manual; Revision C, January 2003
CARESCAPE V100 Vital Signs Monitor
B-5
Appropriate use of NIBP simulators: Appropriate use of NIBP simulators
For your notes
B-6
CARESCAPE V100 Vital Signs Monitor
2048723-002D
C
2048723-002D
Electromagnetic
compatibility (EMC)
CARESCAPE V100 Vital Signs Monitor
C-1
Electromagnetic compatibility (EMC): Electromagnetic compatibility (EMC): CARESCAPE V100 monitor
Electromagnetic compatibility (EMC): CARESCAPE V100
monitor
Changes or modifications to this system not expressly approved by GE
Healthcare can cause EMC issues with this or other equipment. This system is
designed and tested to comply with applicable regulation regarding EMC and
must be installed and put into service according to the EMC information stated
in this appendix.
CAUTION
Use of portable phones or other radio frequency (RF) emitting
equipment near the system may cause unexpected or adverse
operation.
CAUTION
The equipment or system should not be used adjacent to, or
stacked with, other equipment. If adjacent or stacked use is
necessary, the equipment or system should be tested to verify
normal operation in the configuration in which it is being used.
Guidance and manufacturer’s declaration – electromagnetic emissions
The CARESCAPE V100 vital signs monitor is intended for use in the
electromagnetic environment specified below. It is the responsibility of the
customer or user to assure that the CARESCAPE V100 vital signs monitor is used
in such an environment.
Emissions test
Compliance
RF Emissions
EN 55011
Group 1
RF Emissions
EN 55011
Class B
Harmonic Emissions
IEC 61000-3-2
Class A
Voltage Fluctuations/
Flicker Emissions
IEC 61000-3-3
Complies
C-2
Electromagnetic environment – guidance
The equipment uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not likely to cause
any interference in nearby electronic equipment.
The equipment is suitable for use in all establishments, including
domestic establishments and those directly connected to the public
low-voltage power supply network that supplies buildings used for
domestic purposes.
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Electromagnetic compatibility (EMC): Electromagnetic compatibility (EMC): CARESCAPE V100 monitor
Guidance and manufacturer’s declaration – electromagnetic immunity
The CARESCAPE V100 vital signs monitor is intended for use in the
electromagnetic environment specified below. It is the responsibility of the
customer or user to assure that the CARESCAPE V100 vital signs monitor is used
in such an environment.
Immunity test
IEC 60601 test level
Compliance level
Electromagnetic environment – guidance
Electrostatic
Discharge (ESD)
IEC 61000-4-2
± 6 kV contact
± 6 kV contact
± 8 kV air
± 8 kV air
Floors should be wood, concrete or ceramic
tile. If floors are covered with synthetic
material, the relative humidity should be at
least 30%.
Electrical Fast
Transient/Burst
IEC 61000-4-4
± 2 kV for power supply
lines
± 2 kV for power
supply lines
Mains power should be that of a typical
commercial or hospital environment.
±1 kV for input/output
lines
±1 kV for input/
output lines
Surge
IEC 61000-4-5
± 1 kV differential mode
± 1 kV differential
mode
± 2 kV common mode
± 2 kV common
mode
<5% Ut (>95% dip in Ut)
for 0.5 cycles
<5% Ut (>95% dip in
Ut) for 0.5 cycles
<40% Ut (>60% dip in Ut)
for 5 cycles
<40% Ut (>60% dip
in Ut) for 5 cycles
<70% Ut (>30% dip in Ut)
for 25 cycles
<70% Ut (>30% dip
in Ut) for 25 cycles
<5% Ut (>95% dip in Ut)
for 5 s
<5% Ut (>95% dip in
Ut) for 5 s
3 A/m
3 A/m
Voltage dips,
short
interruptions
and voltage
variations on
power supply
input lines
IEC 61000-4-11
Power
Frequency (50/
60 Hz) Magnetic
Field
IEC 61000-4-8
Mains power should be that of a typical
commercial or hospital environment.
Mains power should be that of a typical
commercial or hospital environment. If the
user of the equipment requires continued
operation during power mains interruptions, it
is recommended that the equipment be
powered from an uninterruptible power
supply or a battery.
Power frequency magnetic fields should be at
levels characteristics of a typical location in a
typical commercial or hospital environment.
NOTE:
Ut is the AC mains voltage prior to application of the test level.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
C-3
Electromagnetic compatibility (EMC): Electromagnetic compatibility (EMC): CARESCAPE V100 monitor
Guidance and manufacturer’s declaration – electromagnetic immunity
The CARESCAPE V100 vital signs monitor is intended for use in the
electromagnetic environment specified below. It is the responsibility of the
customer or user to assure that the CARESCAPE V100 vital signs monitor is used
in such an environment.
Immunity test
IEC 60601 test level
Compliance level
Electromagnetic environment – guidance
Portable and mobile RF communications equipment
should not be used closer to any part of the
equipment, including cables, than the recommended
separation distance calculated from the equation
applicable to the frequency of the transmitter.
Recommended separation distance
Conducted RF
IEC 61000-4-6
3 Vrms
150 KHz to 80 MHz
3 V rms
Radiated RF
IEC 61000-4-3
3 V/m
80 MHz to 2.5 GHz
3 V/m
d = 1.2
P
d = 1.2
P 80 MHz to 800 MHz
d = 2.33
P 800 MHz to 2.5 GHz
where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer, and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site surveya, should
be less than the compliance level in each frequency
rangeb.
Interference may occur in the vicinity of equipment
marked with the following symbol:
Note 1: At 80 MHz and 800 MHz, the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by reflection from
structures, objects, and people.
aField strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land
mobile radio, AM and FM radio broadcast, and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site
survey should be considered. If the measured field strength in the location in which the equipment is used
exceeds the applicable RF compliance level above, the equipment should be observed to verify normal
operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the equipment.
bOver the frequency range 150 KHz to 80 MHz, field strengths should be less than 3 V/m.
C-4
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Electromagnetic compatibility (EMC): Electromagnetic compatibility (EMC): CARESCAPE V100 monitor
Recommended separation distances
The table below provides the recommended separation distances (in meters)
between portable and mobile RF communications equipment and the
CARESCAPE V100 vital signs monitor.
The CARESCAPE V100 vital signs monitor is intended for use in the
electromagnetic environment on which radiated RF disturbances are controlled.
The customer or the user of the CARESCAPE V100 vital signs monitor can help
prevent electromagnetic interference by maintaining a minimum distance
between portable and mobile RF communications equipment (transmitters) and
the CARESCAPE V100 vital signs monitor as recommended below, according to
the maximum output power of the communications equipment.
Separation distance in meters (m) according to frequency of transmitter
Rated maximum output
power of transmitter in
watts
150 kHz to 80 MHz a
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
a
P
d = 1.2
80 MHz to 800 MHz a
d = 1.2
800 MHz to 2.5 GHz a
P
d = 2.33
P
At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
For transmitters rated at a maximum output power not listed above, the
recommended separation distance [d] in meters (m) can be estimated using the
equitation applicable to the frequency of the transmitter, where P is the
maximum output power rating of the transmitter in watts (W) according to the
transmitter manufacturer.
NOTE:
These guidelines may not apply in all instances. Electromagnetic
propagation is affected by absorption and reflection from structures,
objects and people.
2048723-002D
CARESCAPE V100 Vital Signs Monitor
C-5
Electromagnetic compatibility (EMC): Electromagnetic compatibility (EMC): CARESCAPE V100 monitor
Compliant cables and accessories
CAUTION
The use of accessories, transducers and cables other than
those specified may result in increased emissions or decreased
immunity performance of the equipment or system.
The table below lists cables, transducers, and other applicable accessories with
which GE Healthcare claims EMC compliance.
NOTE:
Any supplied accessories that do not affect EMC compliance are not
included.
Part number
Description
Maximum lengths
Temperature cables and probes
2008774-001
Alaris Turbo Temp Oral Probe, White cord, Blue
3.0 m / 10 ft
2008775-001
Alaris Turbo Temp Rectal Probe, White cord, Red
3.0 m / 10 ft
2041178-001
Alaris Sensor Tri-Site Oral Probe, White Cord (Blue)
3.0 m / 10 ft
2041179-001
Alaris Sensor Tri-Site Rectal Probe, White Cord (Red)
3.0 m / 10 ft
2044860-001
Exergen TAT-5000, default °F, arterial reference (DINAMAP version)
Not specified
2044860-002
Exergen TAT-5000, default °C, arterial reference (DINAMAP version)
Not specified
2044860-003
Exergen TAT-5000, default °C, oral reference (DINAMAP version)
Not specified
2044860-004
Exergen TAT-5000, default °F, oral reference (DINAMAP version)
Not specified
2044860-005
Cable, Exergen TAT-5000 to V100 interface
2.4 m / 8 ft
Oximetry cables and sensors
70124033
Nellcor Multisite Sensor, D-YS, Reusable
Not specified
70124021
Nellcor DuraSensor Reusable Finger Probe (DS100A)
1.0 m / 3.3 ft
2021406-001
Cable Assy SpO2 Nellcor OxiMax - Smart
3.0 m / 10 ft
2021406-002
Cable Assy SpO2 Nellcor OxiMax - Smart
1.2 m / 4 ft
407705-005
SpO2 Sensor, Max-R, Adhesive, Nasal, 24/box
Not specified
70124026
SpO2 Sensor, Max-I Infant, Adhesive, Sensor, 24/box
Not specified
70124032
SpO2 Sensor, Max-N Neonate Foot Adhesive Sensor, 24/box
Not specified
70124022
SpO2 Sensor, Max-P Pediatric Finger Adhesive Sensor, 24/box
Not specified
70124027
SpO2 Sensor, Max-A Adult Finger Adhesive Sensor, 24/box
Not specified
C-6
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Electromagnetic compatibility (EMC): Electromagnetic compatibility (EMC): CARESCAPE V100 monitor
Part number
Description
Maximum lengths
2028117-001
SpO2 Sensor, Max-AL Adult Long Finger Adhesive Sensor, 24/box
Not specified
414248-001
OXIBAND (OXI-P/I) Pediatric/Infant Sensor
Not specified
414248-002
OXIBAND (OXI-A/N) Adult/Pediatric Sensor
Not specified
2017002-001
Masimo LNOP, SpO2 cable assembly
3.6 m / 12 ft
2017002-003
Masimo LNOP, SpO2 cable assembly
2.4 m / 7.9 ft
2002800-001
Masimo LNOP Reusable Finger Sensor LNOP/DCI Adult
1.0 m / 3.3 ft
2027263-002
Masimo LNC-10 cable assembly
3.0 m / 10 ft
2002799-001
Masimo LNOP Reusable Finger Sensor LNOP/DCI Pediatric
1.0 m / 3.3 ft
2027258-001
Masimo LNCS Reusable Adult Sensor
Not specified
2010458-001
Masimo Disp Adhesive Sensor, LNOP-ADT. Adult (20/box)
Not specified
2010459-001
Masimo Disp Adhesive Sensor, LNOP-PDT. Pediatric (20/box)
Not specified
2010461-001
Masimo Disp Adhesive Sensor, LNOP-NeoPT. Neonatal (20/box)
Not specified
2010460-001
Masimo Disp Adhesive Sensor Bridge, LNOP-NEO. Neonatal (20/box)
Not specified
2017089-001
Masimo Disp Adhesive Sensor, LNOP-Neo-L. Neonatal (20/box)
Not specified
2017090-001
Masimo Disp Adhesive Sensor, LNOP-NeoPT-L. Neonatal (20/box)
Not specified
2027269-001
Masimo Disp Adhesive Sensor Transparent Tape LNOP, Adult (20/box)
Not specified
2027270-001
Masimo Disp Adhesive Sensor Transparent Tape LNOP, Pediatric (20/box)
Not specified
2027271-001
Masimo LNOP Disposable LNOP Hi Fi Sensor Neonatal/Adult (20/box)
Not specified
2027272-001
Masimo LNOP Disposable LNOP Hi Fi Sensor Neonatal/Adult (20/box)
Not specified
2027273-001
Masimo LNOP Disposable LNOP Blue Infant Thumb/Toe Sensor (20/box)
Not specified
2010463-001
Masimo LNOP Reusable Multisite Sensor LNOP-YI
Not specified
2027274-001
Masimo LNOP Reusable Tip-Clip Ear Sensor LKNOP TC-I
Not specified
2009745-001
Masimo LNOP Reusable Finger Sensor Adult DC-195
Not specified
2027259-001
Masimo LNCS DC-IP Reusable Pediatric Sensor
Not specified
2027261-001
Masimo LNCS TC-I TipClip Reusable Ear Sensor
Not specified
2027253-001
Masimo LNCS Adult Adhesive Sensor, 20/box
Not specified
2027254-001
Masimo LNCS Pediatric Adhesive Sensor, 20/box
Not specified
2027255-001
Masimo LNCS Infant Adhesive Sensor, 20/box
Not specified
2027256-001
Masimo LNCS Neonatal Adhesive Sensor, 20/box
Not specified
2027257-001
Masimo LNCS Neonatal PT Adhesive Sensor, 20/box
Not specified
TS-F-D
TruSignal Finger Sensor
1.0 m / 3.3 ft
2048723-002D
CARESCAPE V100 Vital Signs Monitor
C-7
Electromagnetic compatibility (EMC): Electromagnetic compatibility (EMC): CARESCAPE V100 monitor
Part number
Description
Maximum lengths
TS-E-D
TruSignal Ear Sensor
1.0 m / 3.3 ft
TS-W-D
TruSignal Wrap Sensor
1.0 m / 3.3 ft
TS-SE-3
TruSignal Sensitive Skin Sensor
1.0 m / 3.3 ft
TS-AF-10
TruSignal AllFit Sensor, 10/box
0.5 m / 1.6 ft
TS-AF-25
TruSignal AllFit Sensor, 25/box
0.5 m / 1.6 ft
TS-G3
TruSignal Interconnect cable with GE connector
3.0 m / 9.8 ft
TS-F4-GE
TruSignal Finger Sensor with integrated cable, 4 m
4.0 m / 13.1 ft
TS-F2-GE
TruSignal Finger Sensor with integrated cable, 2 m
2.0 m / 6.6 ft
TS-E4-GE
TruSignal Ear Sensor with integrated cable, 4 m
4.0 m / 13.1 ft
TS-E2-GE
TruSignal Ear Sensor with integrated cable, 2 m
2.0 m / 6.6 ft
TS-SA4-GE
TruSignal Soft Adult Sensor with integrated cable and GE connector, 4 m
4.0 m / 13.1 ft
TS-SA-D
TruSignal Soft Adult Sensor with integrated cable and D connector, 1 m
1.0 m / 3.3 ft
405535-002
Power supply cord, hospital grade (US) 10A 125V
3.7 m / 12 ft
405535-014
Power supply cord, Japan ST-ST PSE 10A 250V 12FT
3.7 m / 12 ft
401855-101
Power supply cord, continental Europe 10A 250V
2.5 m / 8.2 ft
401855-102
Power supply cord, British 10A 250V
2.5 m / 8.2 ft
401855-103
Power supply cord, Italian 10A 250V
2.5 m / 8.2 ft
401855-110
Power supply cord, Australian 10A 250V
2.5 m / 8.2 ft
401855-108
Power supply cord, Indian 10A 250V
2.5 m / 8.2 ft
2018859-001
Universal AC/DC adapter
Not specified
2018859-004
Universal AC/DC adapter (Japan only; PSE-marked)
Not specified
001926
Isolated Level Converter, ILC 1926
Not specified
001931
Isolated Level Converter, ILC 1931
Not specified
001932
Isolated Level Converter, ILC 1932
Not specified
2024500-001
Patient ID IR Cable
Not specified
487208CR
DINAMAP Compact Remote Alarm Cable
Not specified
418497-002
Cable Assy, Telemetry Interface, Dinalink
1.8 m / 6 ft
683235
Cable Assy, Dinamap PLUS / Compact to V-link transmitter, EX
165 cm
683242
Cable Assy, ILC to PC
3.0 m / 10 ft
2040229-001
USB cable kit, DINAMAP to PC
1.8 m / 6 ft
Accessories
C-8
CARESCAPE V100 Vital Signs Monitor
2048723-002D
Asia Headquarters
GE Medical Systems
Information Technologies, Inc.
8200 West Tower Avenue
Milwaukee, WI 53223 USA
Tel:
+ 1 414 355 5000
1 800 558 5120 (US only)
Fax: + 1 414 355 3790
GE Medical Systems
Information Technologies, GmbH
Munzingerstrasse 5
79111 Freiburg
Germany
Tel:
+ 49 761 45 43 - 0
Fax: + 49 761 45 43 - 233
GE Medical Systems
Information Technologies, Inc. Asia; GE (China) Co., Ltd.
No1 Huatuo Road,
Zhangjiang Hi-tech Park Pudong
Shanghai, P.R. China 201203
Tel:
+ 86 21 5257 4650
Fax: + 86 21 5208 2008
GE Medical Systems Information Technologies, Inc., a General Electric Company, doing business as
GE Healthcare.
www.gehealthcare.com
0459
Download PDF