MSI | IM-QM67 | User`s manual | MSI IM-QM67 User`s manual

Specification
IM-QM67
Version: October 2011
IM-QM67
MS-9887 (v1.x) Industrial Computer Board
Data Modul AG - www.data-modul.com
▍ Preface
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no
guarantee is given as to the correctness of its contents. Our products are under
continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
■
■
■
■
■
■
■
■
■
■
■
■
MSI® is registered trademark of Micro-Star Int’l Co.,Ltd.
NVIDIA® is registered trademark of NVIDIA Corporation.
ATI® is registered trademark of ATI Technologies, Inc.
AMD® is registered trademarks of AMD Corporation.
Intel® is registered trademarks of Intel Corporation.
Windows® is registered trademarks of Microsoft Corporation.
AMI® is registered trademark of Advanced Micro Devices, Inc.
Award® is a registered trademark of Phoenix Technologies Ltd.
Sound Blaster® is registered trademark of Creative Technology Ltd.
Realtek® is registered trademark of Realtek Semiconductor Corporation.
JMicron® is registered trademark of JMicron Technology Corporation.
Netware® is a registered trademark of Novell, Inc.
Revision History
Revision
Revision History
Date
v1.1
For PCB v1.x
2011 / 04
v1.2
Adding BIOS chapter
2011 / 08
Technical Support
If a problem arises with your system and no solution can be obtained from the
user’s manual, please contact your place of purchase or local distributor. Alternatively, please try the following help resources for further guidance.
◙
◙
Visit the MSI website for FAQ, technical guide, BIOS updates,
driver updates, and other information: http://www.msi.com/index.
php?func=service
Contact our technical staff at: http://ocss.msi.com
ii
Data Modul AG - www.data-modul.com
MS-9887
Safety Instructions
■
■
■
■
■
■
■
■
■
■
■
■
Always read the safety instructions carefully.
Keep this User’s Manual for future reference.
Keep this equipment away from humidity.
Lay this equipment on a reliable flat surface before setting it up.
The openings on the enclosure are for air convection hence protects the
equipment from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source and adjust properly 110/220V
before connecting the equipment to the power inlet.
Place the power cord such a way that people can not step on it. Do not
place anything over the power cord.
Always Unplug the Power Cord before inserting any add-on card or module.
All cautions and warnings on the equipment should be noted.
Never pour any liquid into the opening that could damage or cause electrical shock.
If any of the following situations arises, get the equipment checked by service personnel:
◯
◯
◯
◯
The power cord or plug is damaged.
◯
◯
The equipment has dropped and damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well or you can not get it work according
to User’s Manual.
The equipment has obvious sign of breakage.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60oC (140oF), IT MAY DAMAGE THE EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer.
警告使用者:
這是甲類資訊產品,在居住的環境中使用時,可能會造成無線電干擾,在這種情
況下,使用者會被要求採取某些適當的對策。
廢電池請回收
For better environmental protection, waste batteries should be
collected separately for recycling special disposal.
iii
Data Modul AG - www.data-modul.com
▍ Preface
FCC-B Radio Frequency Interference Statement
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the measures listed below.
◯
◯
◯
Reorient or relocate the receiving antenna.
◯
Consult the dealer or an experienced radio/television technician for help.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Notice 1
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to
comply with the emission limits.
Micro-Star International
MS-9887
VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1)
this device may not cause harmful interference, and
2)
this device must accept any interference received, including interference that
may cause undesired operation.
iv
Data Modul AG - www.data-modul.com
MS-9887
WEEE (Waste Electrical and Electronic Equipment) Statement
ENGLISH
To protect the global environment and as an environmentalist, MSI must remind you that...
Under the European Union (“EU”) Directive on Waste Electrical and Electronic
Equipment, Directive 2002/96/EC, which takes effect on August 13, 2005,
products of “electrical and electronic equipment” cannot be discarded as municipal waste
anymore and manufacturers of covered electronic equipment will be obligated to take back
such products at the end of their useful life. MSI will comply with the product take back
requirements at the end of life of MSI-branded products that are sold into the EU. You can
return these products to local collection points.
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt
Gemäß der Richtlinie 2002/96/EG über Elektro- und Elektronik-Altgeräte dürfen Elektround Elektronik-Altgeräte nicht mehr als kommunale Abfälle entsorgt werden. MSI hat
europaweit verschiedene Sammel- und Recyclingunternehmen beauftragt, die in die Europäische Union in Verkehr gebrachten Produkte, am Ende seines Lebenszyklus zurückzunehmen. Bitte entsorgen Sie dieses Produkt zum gegebenen Zeitpunkt ausschliesslich
an einer lokalen Altgerätesammelstelle in Ihrer Nähe.
FRANÇAIS
En tant qu’écologiste et afin de protéger l’environnement, MSI tient à rappeler ceci...
Au sujet de la directive européenne (EU) relative aux déchets des équipement électriques
et électroniques, directive 2002/96/EC, prenant effet le 13 août 2005, que les produits
électriques et électroniques ne peuvent être déposés dans les décharges ou tout simplement mis à la poubelle. Les fabricants de ces équipements seront obligés de récupérer
certains produits en fin de vie. MSI prendra en compte cette exigence relative au retour des
produits en fin de vie au sein de la communauté européenne. Par conséquent vous pouvez
retourner localement ces matériels dans les points de collecte.
РУССКИЙ
Компания MSI предпринимает активные действия по защите окружающей среды,
поэтому напоминаем вам, что....
В соответствии с директивой Европейского Союза (ЕС) по предотвращению
загрязнения окружающей среды использованным электрическим и электронным
оборудованием (директива WEEE 2002/96/EC), вступающей в силу 13 августа 2005
года, изделия, относящиеся к электрическому и электронному оборудованию, не могут
рассматриваться как бытовой мусор, поэтому производители вышеперечисленного
электронного оборудования обязаны принимать его для переработки по окончании
срока службы. MSI обязуется соблюдать требования по приему продукции, проданной
под маркой MSI на территории EC, в переработку по окончании срока службы. Вы
можете вернуть эти изделия в специализированные пункты приема.
Data Modul AG - www.data-modul.com
▍ Preface
ESPAÑOL
MSI como empresa comprometida con la protección del medio ambiente, recomienda:
Bajo la directiva 2002/96/EC de la Unión Europea en materia de desechos y/o equipos
electrónicos, con fecha de rigor desde el 13 de agosto de 2005, los productos clasificados
como “eléctricos y equipos electrónicos” no pueden ser depositados en los contenedores
habituales de su municipio, los fabricantes de equipos electrónicos, están obligados a
hacerse cargo de dichos productos al termino de su período de vida. MSI estará comprometido con los términos de recogida de sus productos vendidos en la Unión Europea
al final de su periodo de vida. Usted debe depositar estos productos en el punto limpio
establecido por el ayuntamiento de su localidad o entregar a una empresa autorizada para
la recogida de estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan herinneren dat….
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en
Electronische producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen
niet meer beschouwd worden als vervuiling. Fabrikanten van dit soort producten worden verplicht om producten retour te nemen aan het eind van hun levenscyclus. MSI zal
overeenkomstig de richtlijn handelen voor de producten die de merknaam MSI dragen
en verkocht zijn in de EU. Deze goederen kunnen geretourneerd worden op lokale inzamelingspunten.
SRPSKI
Da bi zaštitili prirodnu sredinu, i kao preduzeće koje vodi računa o okolini i prirodnoj sredini,
MSI mora da vas podesti da…
Po Direktivi Evropske unije (“EU”) o odbačenoj ekektronskoj i električnoj opremi, Direktiva
2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju pod “elektronsku i električnu opremu” ne mogu više biti odbačeni kao običan otpad i proizvođači
ove opreme biće prinuđeni da uzmu natrag ove proizvode na kraju njihovog uobičajenog
veka trajanja. MSI će poštovati zahtev o preuzimanju ovakvih proizvoda kojima je istekao
vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode možete vratiti na
lokalnim mestima za prikupljanje.
POLSKI
Aby chronić nasze środowisko naturalne oraz jako firma dbająca o ekologię, MSI przypomina, że...
Zgodnie z Dyrektywą Unii Europejskiej (“UE”) dotyczącą odpadów produktów elektrycznych i elektronicznych (Dyrektywa 2002/96/EC), która wchodzi w życie 13 sierpnia 2005,
tzw. “produkty oraz wyposażenie elektryczne i elektroniczne “ nie mogą być traktowane
jako śmieci komunalne, tak więc producenci tych produktów będą zobowiązani do odbierania ich w momencie gdy produkt jest wycofywany z użycia. MSI wypełni wymagania
UE, przyjmując produkty (sprzedawane na terenie Unii Europejskiej) wycofywane z użycia.
Produkty MSI będzie można zwracać w wyznaczonych punktach zbiorczych.
vi
Data Modul AG - www.data-modul.com
MS-9887
TÜRKÇE
Çevreci özelliğiyle bilinen MSI dünyada çevreyi korumak için hatırlatır:
Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü olacaktır.
Avrupa Birliği’ne satılan MSI markalı ürünlerin kullanım süreleri bittiğinde MSI ürünlerin
geri alınması isteği ile işbirliği içerisinde olacaktır. Ürünlerinizi yerel toplama noktalarına
bırakabilirsiniz.
ČESKY
Záleží nám na ochraně životního prostředí - společnost MSI upozorňuje...
Podle směrnice Evropské unie (“EU”) o likvidaci elektrických a elektronických výrobků
2002/96/EC platné od 13. srpna 2005 je zakázáno likvidovat “elektrické a elektronické
výrobky” v běžném komunálním odpadu a výrobci elektronických výrobků, na které se
tato směrnice vztahuje, budou povinni odebírat takové výrobky zpět po skončení jejich životnosti. Společnost MSI splní požadavky na odebírání výrobků značky MSI,
prodávaných v zemích EU, po skončení jejich životnosti. Tyto výrobky můžete odevzdat
v místních sběrnách.
MAGYAR
Annak érdekében, hogy környezetünket megvédjük, illetve környezetvédőként fellépve az
MSI emlékezteti Önt, hogy ...
Az Európai Unió („EU”) 2005. augusztus 13-án hatályba lépő, az elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK irányelve szerint az elektromos és
elektronikus berendezések többé nem kezelhetőek lakossági hulladékként, és az ilyen
elektronikus berendezések gyártói kötelessé válnak az ilyen termékek visszavételére
azok hasznos élettartama végén. Az MSI betartja a termékvisszavétellel kapcsolatos
követelményeket az MSI márkanév alatt az EU-n belül értékesített termékek esetében,
azok élettartamának végén. Az ilyen termékeket a legközelebbi gyűjtőhelyre viheti.
ITALIANO
Per proteggere l’ambiente, MSI, da sempre amica della natura, ti ricorda che….
In base alla Direttiva dell’Unione Europea (EU) sullo Smaltimento dei Materiali Elettrici ed
Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti alla
categoria dei Materiali Elettrici ed Elettronici non possono più essere eliminati come rifiuti
municipali: i produttori di detti materiali saranno obbligati a ritirare ogni prodotto alla fine del
suo ciclo di vita. MSI si adeguerà a tale Direttiva ritirando tutti i prodotti marchiati MSI che
sono stati venduti all’interno dell’Unione Europea alla fine del loro ciclo di vita. È possibile
portare i prodotti nel più vicino punto di raccolta
vii
Data Modul AG - www.data-modul.com
▍ Preface
▍ Contents
Copyright Notice�������������������������������������������������������������������������������������������������� ii
Trademarks���������������������������������������������������������������������������������������������������������� ii
Revision History�������������������������������������������������������������������������������������������������� ii
Technical Support����������������������������������������������������������������������������������������������� ii
Safety Instructions��������������������������������������������������������������������������������������������� iii
FCC-B Radio Frequency Interference Statement�������������������������������������������� iv
WEEE (Waste Electrical and Electronic Equipment) Statement��������� v
Chapter 1 Overview������������������������������������������������������������������������������������������ 1-1
Mainboard Specifications��������������������������������������������������������������������������� 1-2
Mainboard Layout�������������������������������������������������������������������������������������� 1-4
Chapter 2 Hardware Setup������������������������������������������������������������������������������ 2-1
Quick Components Guide�������������������������������������������������������������������������� 2-2
CPU (Central Processing Unit)������������������������������������������������������������������ 2-3
Memory ����������������������������������������������������������������������������������������������������� 2-5
Power Supply��������������������������������������������������������������������������������������������� 2-6
Back Panel I/O������������������������������������������������������������������������������������������� 2-7
Connector�������������������������������������������������������������������������������������������������� 2-9
Jumper����������������������������������������������������������������������������������������������������� 2-15
Slot����������������������������������������������������������������������������������������������������������� 2-17
Chapter 3 BIOS Setup�������������������������������������������������������������������������������������� 3-1
Entering Setup������������������������������������������������������������������������������������������� 3-2
The Menu Bar�������������������������������������������������������������������������������������������� 3-4
Main����������������������������������������������������������������������������������������������������������� 3-5
Advanced��������������������������������������������������������������������������������������������������� 3-7
Boot���������������������������������������������������������������������������������������������������������� 3-13
Security���������������������������������������������������������������������������������������������������� 3-14
Chipset����������������������������������������������������������������������������������������������������� 3-16
Power������������������������������������������������������������������������������������������������������� 3-18
Save & Exit���������������������������������������������������������������������������������������������� 3-20
viii
Data Modul AG - www.data-modul.com
Chapter 1
Overview
Thank you for choosing the IM-QM67, an excellent industrial computer board from MSI.
Based on the innovative Intel® QM67 chipsets for
optimal system efficiency, the IM-QM67 accommodates the Intel® Core™i7 / i5 / i3 or Celeron® processor in rPGA-989 (Socket G2) and supports 2 DDR3
1067/1333/1600 DIMM slots to provide the maximum
of 16GB memory capacity.
In the entry-level and mid-range market segment, the
IM-QM67 provides a high-performance solution for
today’s front-end and general purpose workstation, as
well as in the future.
Data Modul AG - www.data-modul.com
▍ Overview
Mainboard Specifications
CPU
■ Intel® Core™i7 / i5 / i3 or Celeron® processor in
rPGA-989 (Socket G2)
Chipset
■ SKU1: Intel® QM67 Chipset
■ SKU2: Intel® HM65 Chipset (without iAMT function)
Memory
■ 2 unbuffered non-ECC DDR3 1067/1333/1600
DIMM slots
■ Supports the maximum of 16GB
LAN
■ Intel® 82579LM Gigabit Fast Ethernet controller
■ Intel® 82574L Gigabit Fast Ethernet controller
SATA
■ 2 SATA 6Gb/s ports (SATA1~2)
■ 2 SATA 3Gb/s ports (SATA3~4)
Audio
■ Realtek® ALC887 VD2-GR Codec
Graphics
■ Onboard graphics integrated in Intel® HD Graphics
Back
Panel I/O
& Connectors/Pinheaders
■ Back Panel I/O
- 1 PS/2 mouse port
- 1 PS/2 keyboard port
- 1 VGA port
- 1 HDMI port
- 2 DVI-D ports
- 4 USB 2.0 ports
- 2 Gigabit LAN jacks
- 3 flexible audio ports
■ Onboard Connectors/Pinheaders
- 2 USB 2.0 pinheaders (4 ports)
- 4 serial port connectors
- 2 serial port power jumpers
- 1 deep sleep mode jumper
- 2 SATA 6Gb/s + 2 SATA 3Gb/s connectors
- 2 SATA power connectors
- 1 front panel pinheader
- 1 chassis intrusion connector
- 1 GPIO connector
- 1 LVDS connector
- 1 LVDS power jumper
- 1 amplifier pinheader
1-2
Data Modul AG - www.data-modul.com
MS-9887
Slot
■ 1 CFast slot
■ 1 Mini PCI Express x 1 slot
■ 1 32-bit 33/66MHz 3.3v PCI slot
Form Factor
■ Mini-ITX: 17.0cm x 17.0cm
Environmental
■ Operating Temperature: -10oC to 60oC
■ Storage Temperature: -20oC to 80oC
■ Humidity: 0% ~ 95% RH, Non-Condensing
1-3
Data Modul AG - www.data-modul.com
▍ Overview
Mainboard Layout
Back Panel
Top : mouse
Bottom:
keyboard
Top: VGA port
Bottom: HDMI port
Top:DVI-D port
Bottom: DVI-D port
Chassis Intrusion Connector
Top:
LAN Jack
Bottom:
USB 2.0 ports
Codec
JAMP1
Audio power amplifier Connector
Top:
LAN Jack
Bottom:
USB 2.0 ports
T: Line-In
M: Line-Out
B: Mic
GPIO Connector
Power
Connector
CPU
PCI1
DIMM1
DIMM2
COM3
COM1
COM2
COM4
System Fan & CPU
Connectors
Mini PCI Express Slot
JCMV1
SATA2
SATA1
SATA4
SATA3
JCMV2
SYSFAN1
Mini PCI Express Slot
CPUFAN1
JCMOS1
Mouse
Port
JUSB1
JUSB2
JFP1
Front Panel
Connector
JSPI1
Intel
QM67
JLVDS1
JSATA_PWR2
J2
SATA Power
Connectors
Clear CMOS Jumper
JSPI1 Connector
JSATA_PWR1
J_ME1
LVDS Connector
JDSW1
JCASE1
JME Connector
LVDS
Power
Connector
Super I/O
Chipset
Deep
Sleep
Mode Jumper
DIMM Slots
JGPIO1
PCI Slot
COM Port Power
Jumper
USB Con- SATA ConSerial Port
Connectors
nectors
nectors
COM Port
Power Jumper
LAN Ports
D-Sub Port
DVI-D Port
Line-In
Line-Out
MIC
Keyboard HDMI Port
Port
DVI-D Port
USB 2.0 Ports
1-4
Data Modul AG - www.data-modul.com
MS-9887
CFast Slot
CFast Slot
1-5
Data Modul AG - www.data-modul.com
Chapter 2
Hardware Setup
This chapter provides you with the information on
mainboard hardware configurations. Incorrect setting
of jumpers and connectors may damage your mainboard. Please pay special attention not to connect
these headers in wrong direction. DO NOT adjust any
jumper while the mainboard is powered on.
Data Modul AG - www.data-modul.com
▍ Hardware Setup
Quick Components Guide
Back Panel
I/O, p.2-7
JGPIO1, p2-12
JPWR1, p.2-6
JAMP1, p.2-15
CPU, p.2-3
JCASE1, p.2-9
PCI Slot, p.2-17
DIMM Slot, p.2-5
JCMOS1, p.2-15
JDSW1, p.2-16
JSPI1, p.2-14
J_ME1, p.2-14
CPUFAN1/SYSFAN1,
p.2-10
J2, p.2-16
JLVDS1, p.2-11
Mini PCI Express
Slot, p.2-17
JSATA_PWR1/2,
p.2-10
JCMV1, p.2-15
JFP1, p.2-11
JUSB1/2,
p.2-12
SATA1~4, JCMV2,
p.2-15
p.2-9
COM1/2,
p.2-13
2-2
Data Modul AG - www.data-modul.com
MS-9887
CPU (Central Processing Unit)
When you are installing the CPU, make sure that you install the cooler
to prevent overheating. If you do not have the CPU cooler, consult your
dealer before turning on the computer.
Important
Overheating
Overheating will seriously damage the CPU and system. Always make
sure the cooling fan can work properly to protect the CPU from overheating. Make sure that you apply an even layer of thermal paste (or thermal
tape) between the CPU and the heatsink to enhance heat dissipation.
Replacing the CPU
While replacing the CPU, always turn off the power supply or unplug the
power supply’s power cord from the grounded outlet first to ensure the
safety of CPU.
2-3
Data Modul AG - www.data-modul.com
▍ Hardware Setup
CPU Installation
1.
Locate the CPU socket on the mainboard. On the upper end of the
CPU socket is a socket actuator in the form of a slotted screw head.
Make sure that you open or close the socket with a flathead screwdriver before and after installing the CPU.
2.
Turn the socket actuator counterclockwise to open the socket. Locate the golden arrow on the CPU and align it to the upper right
corner of the socket. Put the CPU gently down. If the socket is completely opened, the CPU pins will securely fit into the socket.
3.
Turn the socket actuator clockwise to close the socket.
Important
Mainboard photos shown in this section are for demonstration only and
may differ from the actual look of your mainboard.
2-4
Data Modul AG - www.data-modul.com
MS-9887
Memory
These DIMM slots are intended for memory modules.
DDR3 SO-DIMM Slot 204-pin
Installing Memory Modules
1.
Locate the DIMM1 SO-DIMM slot. Align the notch on the DIMM with
the key on the slot and insert the DIMM into the slot at 45-degree
angle.
2.
Push the DIMM gently forwards until the slot levers click and lock
the DIMM in place. Follow the same procedures to install the second
DIMM if necessary.
3.
To uninstall the DIMM, flip the slot levers outwards and the DIMM
will be released instantly.
Important
•
You can barely see the golden finger if the DIMM is properly inserted
in the DIMM slot.
•
To enable successful system boot-up, always insert the DIMM into
the DIMM1 first.
2-5
Data Modul AG - www.data-modul.com
▍ Hardware Setup
Power Supply
Power Connector: JPWR1
This connector provides power to the mainboard.
d
n
u d
ro un
.G ro
1 .G
2
V
2
1 V
.+ 2
3 .+1
4
2-6
Data Modul AG - www.data-modul.com
MS-9887
Back Panel I/O
Mouse
Port
LAN Ports
D-Sub Port
DVI-D Port
Line-In
Line-Out
MIC
Keyboard HDMI Port
Port
DVI-D Port
USB 2.0 Ports
▶ Keyboard Port
The standard PS/2 keyboard DIN connector is for a PS/2 keyboard.
▶ Mouse Port
The standard PS/2 mouse DIN connector is for a PS/2 mouse.
▶ D-Sub Port
The DB15-pin female connector is provided for monitor.
▶ HDMI Port
The High-Definition Multimedia Interface (HDMI) is an all-digital audio/
video interface capable of transmitting uncompressed streams. HDMI
supports all TV format, including standard, enhanced, or high-definition
video, plus multi-channel digital audio on a single cable.
▶ DVI-D Port
The DVI-D (Digital Visual Interface-Digital) connector allows you to connect an LCD monitor. It provides a high-speed digital interconnection between the computer and its display device. To connect an LCD monitor,
simply plug your monitor cable into the DVI connector, and make sure that
the other end of the cable is properly connected to your monitor (refer to
your monitor manual for more information.)
▶ USB Port
The USB (Universal Serial Bus) port is for attaching USB devices such as
keyboard, mouse, or other USB-compatible devices.
2-7
Data Modul AG - www.data-modul.com
▍ Hardware Setup
▶ LAN Port
The standard RJ-45 LAN jack is for connection to the Local Area Network
(LAN). You can connect a network cable to it.
Activity Indicator
Speed Indicator
Left LED
LED Color
10M Cable
Plug-in
100M Cable
Plug-in
1000M Cable
Plug-in
Right LED
Active LED
100M/1000M Speed LED
Yellow
Green/Orange
No Transmission
OFF
OFF
Transmission
Yellow (Blinking)
OFF
No Transmission
OFF
Green (Lighting)
Transmission
Yellow (Blinking)
Green (Lighting)
No Transmission
OFF
Orange (Lighting)
Transmission
Yellow (Blinking)
Orange (Lighting)
OFF
OFF
In S3/S4/S5 Standby State
▶ Audio Ports
These audio connectors are used for audio devices. It is easy to differentiate between audio effects according to the color of audio jacks.
■
Line-Out (Green) - Line Out, is a connector for speakers or
headphones.
■
Line-In (Blue) - Line In, is used for external CD player, tapeplayer or other audio devices.
■
Mic (Pink) - Mic, is a connector for microphones.
2-8
Data Modul AG - www.data-modul.com
MS-9887
Connector
Chassis Intrusion Connector: JCASE1
This connector is provided to connect the chassis intrusion switch cable.
If the chassis is opened, the chassis intrusion mechanism will be activated. The system will record this status and show a warning message
on the screen. To clear the warning, you must enter the BIOS utility and
clear the record.
d
n
u RU
ro T
.G IN
2 .C
1
Serial ATA Connector: SATA1 ~ SATA4
This connector is a high-speed Serial ATA interface port. Each connector
can connect to one Serial ATA device.
Important
Please do not fold the Serial ATA cable into 90-degree angle. Otherwise,
data loss may occur during transmission.
2-9
Data Modul AG - www.data-modul.com
▍ Hardware Setup
Fan Power Connector: CPUFAN1 / SYSFAN1
The fan power connectors support system cooling fan with +12V. When
connecting the wire to the connectors, always note that the red wire is the
positive and should be connected to the +12V; the black wire is Ground
and should be connected to GND. If the mainboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan
with speed sensor to take advantage of the CPU fan control.
d
n
u
ro 2V or
.G 1 s
1 .+ en
2 .S
3
Important
•
Please refer to the recommended CPU fans at processor’s official
website or consult the vendors for proper CPU cooling fan.
•
Fan cooler set with 3- or 4-pin power connector are both available
for CPUFAN1.
SATA Power Connector: JSATA_PWR1 /2
The connector provides the power to the SATA device.
V d
2 n
1 ou nd
.+ r u
4 .G ro
3 .G V
2 .5
1
2-10
Data Modul AG - www.data-modul.com
MS-9887
LVDS Flat Panel Connector: JLVDS1
The LVDS (Low Voltage Differential Signal) connector provides a digital
interface typically used with flat panels. After connecting an LVDS interfaced flat panel to the JLVDS1, be sure to check the panel datasheet and
set the J2 jumper for proper power voltage.
l
o
tr le
V
2
D K n b N
o
a
1 2V
N
0
D L
.+ 1 V V C t C n A 1 N
1 .+ 12 .3 _V _ h t E AT A 2
3 .+ 3 D C lig h D AT TA N
3
5 .+ C D k ig _ A
7 .L LD ac kl 1 _D D KN TA N
9 . B ac S 1 _ C A
0 N
11 3. .B VD DS S1 1_ D TA 1 N
1 5 .L V D S 1_ A TA 2
A N
1 7 .L V D S
D
1 9 L
_ A T 3
1 1. .LV VD D 2 _D DA KN A
2 3 .L N S 2 _ C AT
2 5 .G VD S 2 _ D
2 7 .L VD S 2 _
2 9 L D S 2
2 1. .LV VD DS
3 3 .L V D
3 5 .L N
3 7 .G
3 9
3
V
2
1 2V
.+ 1 D
2 .+ N D
4 .G N D
6 .G D A
8 _V AT N
D D E D
C _ D N P
.L C D G 0 P
0 D V . A 1 P
1 D S_ 16 AT A 2 P
T K
.L
2 D D A A P
1 LV 1_ _D AT _C 3 D
.
4 S 1 D 1 A N P
1 D S _ S T .G 0 P
V D S1 VD DA28 TA 1 P
_ A TA 2 P
.L V
8 L D .L 1
1 0. .LV 24 S _D A TA CK P D
DA _ 3
22
D
V S2 2_ D 2 A N
2
.L D S 2_ DS AT0.G
6
2 .LV VD S V _D 4
0 L D .L 2
3 2. .LV 36 S
34
D
3 LV
.
8
3
Front Panel Connectors: JFP1
These connectors are for electrical connection to the front panel switches
and LEDs. The JFP1 is compliant with Intel® Front Panel I/O Connectivity
Design Guide.
P
o
w
e
r
0
r
L
E
D
in
P o .
8
.+
.N
6
.4 +
.
2
e
ch
w
it
o
w
1
S
P
ch
it
w
d
e tS
rv se
D
E
se e
L
e R
D
.R
D
9 .+
H
7 .
5 .3 .+
1
Data Modul AG - www.data-modul.com
2-11
▍ Hardware Setup
Front USB Connector: JUSB1 / JUSB2
This connector, compliant with Intel I/O Connectivity Design Guide, is
ideal for connecting high-speed USB interface peripherals such as USB
HDD, digital cameras, MP3 players, printers, modems and the like.
C
.N d
0 n
1 ou 1+
r B .G S 1
8 .U SB C
6 .U VC
4 2.
in
P d
o un +
.N ro 0
9 .G B 07 S B
.U
5 US C
.
3 VC
.
1
Important
Note that the pins of VCC and GND must be connected correctly to avoid
possible damage.
GPIO Connector: JGPIO1
This connector is provided for the General-Purpose Input/Output (GPIO)
peripheral module.
in 3
P O
o P O2
.N G P O1
2 _
1 0.N _G P O0 ut
1 .N G P p
8 .N_ G ut
6 .N_ O
4 .5V
2
D 3
N PI 2
.G G PI 1
t
_
11 .N _G PI 0 pu
9 .N G PI ut
7 .N_ G O
_
5 .N 3V
3 .3.
1
2-12
Data Modul AG - www.data-modul.com
MS-9887
Serial Port Connector: COM1 (RS-232/-422/-485)
Serial Port Connector: COM2~4 (RS-232)
This connector is a 16550A high speed communications port that sends/
receives 16 bytes FIFOs. You can attach a serial device to it through an
optional serial port bracket.
RS-232
RS-232
D
X R
.R T
2 .D SR
4 .D TS
6 .C
8
M
O
C
_
C
C S
.V T
9 .R ND
7 .G XD
5 .T CD
3 .D
1
PIN
SIGNAL
DESCRIPTION
1
2
3
4
5
6
7
8
9
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
VCC_COM
Data Carrier Detect
Receive Data
Transmit Data
Data Terminal Ready
Signal Ground
Data Set Ready
Request To Send
Clear To Send
Power Source
RS-422
RS-422
+
X .R X
2 .R C
4 N C
.
6 .N
8
C
.N C
9 .N D
7 GN +
.
5 .TX X3 .T
1
PIN
SIGNAL
DESCRIPTION
1
2
3
4
5
6
7
8
9
422 TXD422 RXD+
422 TXD+
422 RXDGND
NC
NC
NC
NC
Transmit Data, Negative
Receive Data, Positive
Transmit Data, Positive
Receive Data, Negative
Signal Ground
No Connection
No Connection
No Connection
No Connection
RS-485
RS-485
C
.N C
2 .N C
4 N C
.
6 .N
8
C
.N C
9 .N ND A+
7 G AT A.
5 .D AT
3 .D
1
PIN
SIGNAL
DESCRIPTION
1
2
3
4
5
6
7
8
9
485 TXDNC
485 TXD+
NC
GND
NC
NC
NC
NC
Transmit Data, Negative
No Connection
Transmit Data, Positive
No Connection
Signal Ground
No Connection
No Connection
No Connection
No Connection
2-13
Data Modul AG - www.data-modul.com
▍ Hardware Setup
JSPI1 Connector: JSPI1
This connector is provided for engineer debug only.
J_ME1 Connector: J_ME1
This connector is provided for setting ME firmware update.
1
J_ME1
1
1
Enable
Disable
Audio Amplifier Connector: JAMP1
The JAMP1 is used to connect audio amplifiers to enhance audio performance.
1
PIN
SIGNAL
1
2
3
4
AMP_LAMP_L+
AMP_RAMP_R+
2-14
Data Modul AG - www.data-modul.com
MS-9887
Jumper
Clear CMOS Jumper: JCMOS1
There is a CMOS RAM onboard that has a power supply from an external
battery to keep the data of system configuration. With the CMOS RAM, the
system can automatically boot OS every time it is turned on. If you want to
clear the system configuration, set the jumper to clear data.
1
1
1
JCMOS1
Clear CMOS
Keep Data(Default)
Important
You can clear CMOS by shorting 1-2 pin while the system is off. Then return
to 2-3 pin position. Avoid clearing the CMOS while the system is on; it will
damage the mainboard.
COM1 Power Select Jumper: JCMV1
This jumper specifies the operation voltage of the onboard COM1.
1
JCMV1
1
1
12V
5V(Default)
COM2~4 Power Select Jumper: JCMV2
This jumper specifies the operation voltage of the onboard COM2~4.
1
JCMV2
1
5V(Default)
1
12V
Important
Avoid adjusting the jumper when the system is on; it will damage the mainboard.
2-15
Data Modul AG - www.data-modul.com
▍ Hardware Setup
Deep Sleep Mode Jumper: JDSW1
Use this jumper to specify the deep sleep mode (S4/S5).
1
1
JDSW1
Enable(Default)
1
Disable
Important
Avoid adjusting the jumper when the system is on; it will damage the
mainboard.
LVDS Voltage Select Jumper: J2
This jumper specifies the operation voltage of LVDS.
1
1
J22
3.3V(Default)
1
5V
Important
Avoid adjusting the jumper when the system is on; it will damage the
mainboard.
2-16
Data Modul AG - www.data-modul.com
MS-9887
Slot
Mini PCI (Peripheral Component Interconnect) Express Slot
The mini PCI Express slot supports the mini PCI Express interface expansion card such as wireless LAN, TV tuner, and Robson NAND Flash.
Mini PCI-E Slot
PCI (Peripheral Component Interconnect) Slot
The PCI slot supports LAN card, SCSI card, USB card, and other add-on
cards that comply with PCI specifications.
32-bit PCI Slot
CFast Slot
This socket supports CompactFlash cards.
Important
When adding or removing expansion cards, make sure that you unplug
the power supply first. Meanwhile, read the documentation for the expansion card to configure any necessary hardware or software settings for
the expansion card, such as jumpers, switches or BIOS configuration.
2-17
Data Modul AG - www.data-modul.com
Data Modul AG - www.data-modul.com
Chapter 3
BIOS Setup
This chapter provides information on the BIOS Setup
program and allows you to configure the system for
optimum use.
You may need to run the Setup program when:
■
An error message appears on the screen
during the system booting up, and requests
you to run SETUP.
■
You want to change the default settings for
customized features.
Data Modul AG - www.data-modul.com
▍ BIOS Setup
Entering Setup
Power on the computer and the system will start POST (Power On Self Test)
process. When the message below appears on the screen, press <DEL> or
<F2> key to enter Setup.
Press DEL or F2 to enter SETUP
If the message disappears before you respond and you still wish to enter
Setup, restart the system by turning it OFF and On or pressing the RESET
button. You may also restart the system by simultaneously pressing <Ctrl>,
<Alt>, and <Delete> keys.
Important
•
The items under each BIOS category described in this chapter are under continuous update for better system performance. Therefore, the
description may be slightly different from the latest BIOS and should be
held for reference only.
•
Upon boot-up, the 1st line appearing after the memory count is the BIOS
version. It is usually in the format:
A9887IMS V1.0 011511 where:
1st digit refers to BIOS maker as A = AMI, W = AWARD, and
P = PHOENIX.
2nd - 5th digit refers to the model number.
6th digit refers to the chipset as I = Intel, N = NVIDIA,
A = AMD and V = VIA.
7th - 8th digit refers to the customer as MS = all standard customers.
V1.0 refers to the BIOS version.
011511 refers to the date this BIOS was released.
3-2
Data Modul AG - www.data-modul.com
MS-9887
Control Keys
←→
Select Screen
↑↓
Select Item
+-
Change Field
Tab
Select Field
F1
General Help
F10
Save and Exit
Esc
Exit
Getting Help
After entering the Setup menu, the first menu you will see is the Main
Menu.
Main Menu
The main menu lists the setup functions you can make changes to. You can
use the arrow keys ( ↑↓ ) to select the item. The on-line description of the
highlighted setup function is displayed at the bottom of the screen.
Sub-Menu
If you find a right pointer symbol
appears to the left of certain fields that
means a sub-menu can be launched from this field. A sub-menu contains
additional options for a field parameter. You can use arrow keys ( ↑↓ ) to
highlight the field and press <Enter> to call up the sub-menu. Then you can
use the control keys to enter values and move from field to field within a
sub-menu. If you want to return to the main menu, just press the <Esc >.
General Help <F1>
The BIOS setup program provides a General Help screen. You can call up
this screen from any menu by simply pressing <F1>. The Help screen lists
the appropriate keys to use and the possible selections for the highlighted
item. Press <Esc> to exit the Help screen.
3-3
Data Modul AG - www.data-modul.com
▍ BIOS Setup
The Menu Bar
▶ Main
Use this menu for basic system configurations, such as time, date etc.
▶ Advanced
Use this menu to set up the items of special enhanced features.
▶ Boot
Use this menu to specify the priority of boot devices.
▶ Security
Use this menu to set supervisor and user passwords.
▶ Chipset
This menu controls the advanced features of the onboard Northbridge and
Southbridge.
▶ Power
Use this menu to specify your settings for power management.
▶ Save & Exit
This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes.
3-4
Data Modul AG - www.data-modul.com
MS-9887
Main
▶ System Date
This setting allows you to set the system date. The date format is <Day>,
<Month> <Date> <Year>.
▶ System Time
This setting allows you to set the system time. The time format is <Hour>
<Minute> <Second>.
▶ SATA1/SATA2/SATA3/SATA4/CFast
[Type]
Press PgUp/<+> or PgDn/<-> to select
[Manual], [None] or [Auto] type. Note that the
specifications of your drive must match with
the drive table. The hard disk will not work
properly if you enter improper information for
this category. If your hard disk drive type is
not matched or listed, you can use [Manual] to
define your own drive type manually.
3-5
Data Modul AG - www.data-modul.com
▍ BIOS Setup
[LBA/Large
Mode]
Enabling LBA causes Logical Block Addressing to be used in place of Cylinders, Heads
and Sectors
[Block
(Multi-Sector
Transfer)]
Any selection except Disabled determines the
number of sectors transferred per block
[PIO Mode]
Indicates the type of PIO (Programmed
Input/Output)
[DMA Mode]
Indicates the type of Ultra DMA
[S.M.A.R.T.]
This allows you to activate the S.M.A.R.T.
(Self-Monitoring Analysis & Reporting Technology) capability for the hard disks. S.M.A.R.T
is a utility that monitors your disk status to
predict hard disk failure. This gives you an
opportunity to move data from a hard disk that
is going to fail to a safe place before the hard
disk becomes offline.
[32 Bit Data
Transfer]
Enables 32-bit communication between CPU and IDE controller
3-6
Data Modul AG - www.data-modul.com
MS-9887
Advanced
▶ Quick Boot
Enabling this setting will cause the BIOS power-on self test routine to skip
some of its tests during bootup for faster system boot.
▶ Bootup NumLock State
This setting is to set the Num Lock status when the system is powered on.
Setting to [On] will turn on the Num Lock key when the system is powered
on. Setting to [Off] will allow users to use the arrow keys on the numeric
keypad.
▶ Option ROM Messages
This item is used to display or hide the third-party ROM message.
3-7
Data Modul AG - www.data-modul.com
▍ BIOS Setup
▶ PCI/PCIE Device Configuration
▶ USB Functions
This setting specifies the operation mode of the onboard USB controller.
▶ USB 2.0 Controller
This setting enables/disables the onboard USB controller.
▶ Legacy USB Support
Set to [Enabled] if you need to use any USB 1.1/2.0 device in the operating system that does not support or have any USB 1.1/2.0 driver
installed, such as DOS and SCO Unix.
▶ Audio Controller
This setting enables/disables the onboard audio controller.
▶ GbE LAN Boot
This setting enables/disables GbE LAN boot.
▶ LAN Option ROM
This setting enables/disables the initialization of the onboard LAN Boot
ROM during bootup. Selecting [Disabled] will speed up the boot process.
3-8
Data Modul AG - www.data-modul.com
MS-9887
▶ CPU Configuration
▶ Max CPUID Value Limit
The Max CPUID Value Limit BIOS feature allows you to circumvent
problems with older operating systems that do not support the Intel
Pentium 4 processor with Hyper-Threading Technology. When enabled,
the processor will limit the maximum CPUID input value to 03h when
queried, even if the processor supports a higher CPUID input value.
When disabled, the processor will return the actual maximum CPUID
input value of the processor when queried.
▶ Execute Disable Bit Capability
Intel’s Execute Disable Bit functionality can prevent certain classes of
malicious “buffer overflow” attacks when combined with a supporting
operating system. This functionality allows the processor to classify
areas in memory by where application code can execute and where it
cannot. When a malicious worm attempts to insert code in the buffer,
the processor disables code execution, preventing damage or worm
propagation.
▶ Hyper Threading Technology
The processor uses Hyper-Threading technology to increase transaction rates and reduces end-user response times. The technology treats
the two cores inside the processor as two logical processors that can
execute instructions simultaneously. In this way, the system perfor-
3-9
Data Modul AG - www.data-modul.com
▍ BIOS Setup
mance is highly improved. If you disable the function, the processor will
use only one core to execute the instructions. Please disable this item if
your operating system doesn’t support HT Function, or unreliability and
instability may occur.
▶ Intel(R) SpeedStep(tm) Tech
EIST (Enhanced Intel SpeedStep Technology) allows the system to dynamically adjust processor voltage and core frequency, which can result
in decreased average power consumption and decreased average heat
production.
▶ Intel(R) C-State Tech
C-state performance indicates the ability to run the processor in lower
power states when the PC is idle. This setting enables/disables the CState Configuration for power saving purposes.
▶ Enhanced C-States
This setting enables/disables enhanced C-states.
▶ Super IO Configuration
▶ Serial Port 1/ 2/ 3/ 4 Address, Parallel Port Address
Select an address for the specified serial/parallel port.
▶ Serial Port 1/ 2/ 3/ 4 IRQ
Select a corresponding interrupt for the specified serial port.
▶ Watch Dog Timer
You can enable the system watch-dog timer, a hardware timer that generates a reset when the software that it monitors does not respond as
expected each time the watch dog polls it.
3-10
Data Modul AG - www.data-modul.com
MS-9887
▶ Hardware Monitor
These items display the current status of all monitored hardware devices/
components such as voltages, temperatures and all fans’ speeds.
▶ Smart Fan Configuration
▶ Smart CPUFAN Target
This setting allows users to set a target temperature for the Smart Fan
feature. Smart Fan is an excellent feature which will adjust the CPU/
3-11
Data Modul AG - www.data-modul.com
▍ BIOS Setup
system fan speed automatically depending on the current CPU/system
temperature, avoiding the overheating to damage your system.
▶ FAN1 Type
This setting specifies the fan type.
▶ Min. Speed
This setting specifies the minimum fan speed.
▶ Smart SYSFAN Target
This setting allows users to set a target temperature for the Smart Fan
feature. Smart Fan is an excellent feature which will adjust the CPU/
system fan speed automatically depending on the current CPU/system
temperature, avoiding the overheating to damage your system.
▶ Min. Speed
This setting specifies the minimum fan speed.
▶ GPIO Group Configuration
▶ GPO 1/2/3/4 Data
This setting specifies the GPO data.
3-12
Data Modul AG - www.data-modul.com
MS-9887
Boot
▶ Boot Option #1 / 2 / 3 / 4
This setting allows users to set the sequence of boot devices where BIOS
attempts to load the disk operating system.
3-13
Data Modul AG - www.data-modul.com
▍ BIOS Setup
Security
▶ Adminstrator Password / Adminstrator Supervisor Password
Administrator Password controls access to the BIOS Setup utility. These
settings allow you to set or change the administrator password.
▶ User Password / Change User Password
User Password controls access to the system at boot. These settings allow
you to set or change the user password.
▶ Chassis Intrusion
The field enables or disables the feature of recording the chassis intrusion
status and issuing a warning message if the chassis is once opened. To
clear the warning message, set the field to [Reset]. The setting of the field
will automatically return to the default value later.
3-14
Data Modul AG - www.data-modul.com
MS-9887
▶ Trusted Computing
▶ TCG/TPM Support
This setting controls the Trusted Platform Module (TPM) designed by
the Trusted Computing Group (TCG). TPMs are special-purpose integrated circuits (ICs) built into a variety of platforms to enable strong
user authentication and machine attestation - essential to prevent inappropriate access to confidential and sensitive information and to protect
against compromised networks.
▶ Intel TXT(LT) Configuration
When SMX(Secure Mode Extensons) is enabled, this item can be used to
enable/ disable Intel TXT(Trusted Execution Technology) support.
▶ PCH-FW Configuration
This item is used to disable or enable ME (Management Engine) F/W write
protect and show the ME (Management Engine) F/W information.
▶ AMT Configuration
▶ Intel AMT Support
This setting allows you to enable/disable the Intel Active Management
Technology(AMT) support.
▶ Serial Port Console Redirection
Console Redirection operates in host systems that do not have a monitor and keyboard attached. This setting enables/disables the operation of
console redirection. When set to [Enabled], BIOS redirects and sends all
contents that should be displayed on the screen to the serial COM port for
display on the terminal screen. Besides, all data received from the serial
port is interpreted as keystrokes from a local keyboard.
3-15
Data Modul AG - www.data-modul.com
▍ BIOS Setup
Chipset
▶ Primary Display
This item specifies which is your primary graphics adapter.
▶ Internal Graphics
This setting allows users to select the initiate graphic adapter.
▶ GTT Size
The Graphics Translation Table (GTT) is a Translation Lookaside Buffer
(TLB) used to map the virtual memory space of the graphics aperture to
that of the physical address space. At less 1MB for Intel Smart 2D Display
Technology direct access to the pre-allocated memory space is necessary.
▶ Aperture Size
Aperture memory will not be used until on-board memory is running low.
That means it will usually not impact gaming performance because developers are trying hard to not exceed the on-board memory limits. However
most games requiring more and more texture memory supported. A good
number seems to be 256MB Aperture Size for all. (from 128 MB to 512
MB RAM).
3-16
Data Modul AG - www.data-modul.com
MS-9887
▶ DVMT Pre-Allocated
Intel’s Dynamic Video Memory Technology (DVMT) allows the system to
dynamically allocate memory resources according to the demands of the
system at any point in time. The key idea in DVMT is to improve the efficiency of the memory allocated to either system or graphics processor.
It is recommended that you set this BIOS feature to DVMT Mode for
maximum performance. Setting it to DVMT Mode ensures that system
memory is dynamically allocated for optimal balance between graphics
and system performance.
▶ DVMT Total Gfx Mem
When set to DVMT/FIXED Mode, the graphics driver will allocate a fixedamount of memory as dedicated graphics memory, as well as allow more
system memory to be dynamically allocated between the graphicsprocessor and the operating system.
▶ Primary Boot Display
Use the field to select the type of device you want to use as the display(s)
of the system.
▶ LCD Panel Type
This setting allows you to set your preferences for the boot display device.
▶ Panel Scaling
This item is used for setting screen scaling up or none. (Auto / Off / Force
Scaling)
▶ Active LVDS
This item is used for turning on/off LVDS support. (LVDS or No LVDS)
▶ Panel Color Depth
This item is used for setting the matching LFP Panel color depth. (18bit
or 24bit).
3-17
Data Modul AG - www.data-modul.com
▍ BIOS Setup
Power
▶ ACPI Sleep State
This setting specifies the sleep state that the system will enter when the
suspend button is pressed.
▶ Restore on AC Power Loss
This setting specifies whether your system will reboot after a power failure
or interrupt occurs. Available settings are:
[Power Off]
Leaves the computer in the power off state.
[Power On]
Leaves the computer in the power on state.
[Last State]
Restores the system to the previous status before
power failure or interrupt occurred.
▶ Resume On USB from S3/S4
The item allows the activity of the USB device to wake up the system from
S3 (Suspend to RAM) / S4 sleep state.
▶ Resume On LAN/PCIE/PS2 PME
This field specifies whether the system will be awakened from power saving
3-18
Data Modul AG - www.data-modul.com
MS-9887
modes when activity or input signal of onboard LAN/PCIE/PCI/PS2 PEM
is detected.
▶ Resume On RTC
When [Enabled], your can set the date and time at which the RTC (real-time
clock) alarm awakens the system from suspend mode.
3-19
Data Modul AG - www.data-modul.com
▍ BIOS Setup
Save & Exit
▶ Save Changes and Exit
Save changes to CMOS and exit the Setup Utility.
▶ Discard Changes and Exit
Abandon all changes and exit the Setup Utility.
▶ Save Changes and Reset
Save changes to CMOS and reset the system.
▶ Discard Changes
Abandon all changes.
▶ Load Optimal Defaults
Use this menu to load the default values set by the mainboard manufacturer
specifically for optimal performance of the mainboard.
▶ Save as User Defaults
Save changes as the user’s default profile.
▶ Restore User Defaults
Restore the user’s default profile.
3-20
Data Modul AG - www.data-modul.com
DI SPLAYS AND EMBEDDED SOLUTIONS
DI SPLAYS AND EMBEDDED SOLUTIONS
DATA MODUL Headquarters Munich
Landsberger Str. 322
D-80687 Munich - Germany
Phone: +49-89-56017-0
Fax: +49-89-56017-119
www.data-modul.com
Sales Office Hamburg
Borsteler Chaussee 51
D-22453 Hamburg - Germany
Phone: +49-40-42947377-0
Sales Office Duesseldorf
Fritz-Vomfelde-Str. 8
D-40547 Duesseldorf - Germany
Phone: +49-211-52709-0
Sales Office Scandinavia
Lundsmindevej 5
DK-6000 Kolding - Denmark
Phone: +45-75-224477
DATA MODUL France, S.A.R.L.
Bat B – Hall 204
1-3 Rue des Campanules
F-77185 Lognes - France
Phone: +33-1-60378100
DATA MODUL Italy, S.r.l.
Regus Center Senigallia
Via Senigallia 18/2
I-20161 Milano - Italy
Phone: +39-02-64672509
DATA MODUL Iberia, S.L.
c/ Adolfo Pérez Esquivel 3
Edificio Las Americas III Oficina 40
28230 Parque Empresarial Las Rozas / Madrid - Spain
Phone: +34-916-366458
DATA MODUL Suisse GmbH
Stationsstr. 57
CH-8606 Nänikon - Switzerland
Phone: +41-44-94091-50
DATA MODUL Ltd. / UK
Collins Building
3 Vigo Place - Aldridge - Walsall WS9 8UG - United Kingdom
Phone: +44-121-6988641
DATA MODUL Inc. / USA
275 Marcus Blvd, Unit K
Hauppauge, NY 11788 - USA
Phone: +1-631-951-0800
2 Data Modul AG | Landsberger Str. 322 | 80687 Munich | Tel. +49-89-56017-0 | Fax +49-89-56017-119 | www.data-modul.com
Download PDF