Radio Shack | 49-454 | Owner`s manual | Radio Shack 49-454 Owner`s manual

Please read before using this equipment.
Owner’s Manual
Extra Keypad for
Alarm System
ˆ Contents
Features .............................................. 4
Read This First ................................. 5
A Quick Look at Your Keypad ........... 8
Preparation ......................................... 9
Connecting the Keypad to Your
Alarm System ................................... 9
Assigning an Address .................... 11
Testing the Connection .................. 13
Installing the Keypad ...................... 14
Operation .......................................... 16
Setting the Security Code .............. 16
Arming/Disarming the Alarm .......... 18
Using Annunciate Mode ................. 19
Understanding ARMED and
READY ........................................... 20
© 2000 RadioShack Corporation. All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
2
Contents
Triggering a Panic Alarm ............... 22
Testing the System ........................ 23
Troubleshooting ............................... 24
Care ................................................... 24
Specifications .................................. 26
Contents
3
ˆ Features
Your RadioShack Digital Keypad is a
high quality, UL-listed security keypad that connects to the following
RadioShack security systems.
• 4–16 Zone Security System —
Cat. No. 49-459
• 2-Zone Security System —
Cat. No. 49-454
You can mount the keypad almost anywhere in your home, providing additional
remote locations for disarming and arming the system and for programming access code numbers.
This keypad’s features include:
Armed and Ready Indicators — show
the alarm system’s status.
4
Features
Panic Circuit — lets you quickly trigger
the alarm from the keypad.
Supervised Keypad Circuit — communicates with the main panel and sounds
an alarm if someone tries to remove the
keypad.
Selectable Keypad Address — lets you
add up to 3 additional keypads for extra
convenience.
This product is UL listed under Standard
Number 1023, “Household Burglar-Alarm
System Units.” Use only with UL-listed
security devices.
READ THIS FIRST
Properly connecting and installing the
keypad requires careful planning before
you begin. Read this entire manual and
plan your installation before continuing.
Features
5
This manual includes instructions for
use with both the 49-454 and 49-459
RadioShack security systems. Check
your security system’s owner’s manual
for specific instructions on how to use this
keypad with each particular system.
Here are some important points to consider when planning your installation:
• Where will you mount the keypad?
The keypad is designed only for
indoor installation. It should be
readily accessible to those who will
use it, but should not be easily seen
by an intruder and should be
mounted away from dust, dirt, and
temperature or humidity extremes.
• What other hardware and tools do
you need? You should mount the
keypad in a standard single-gang
6
Features
electrical box (the kind used for single wall switches and AC outlets).
Once you install this box, you will
need four-conductor cable and a
screwdriver to connect the keypad to
your alarm system.
Note: You can mount the keypad directly
on wood or plasterboard walls without an
electrical box. However, the electrical box
gives added stability and protects the
keypad from tampering.
Features
7
ˆ A Quick Look at
Your Keypad
CANCEL
ENTER
ANNC
SET UP
ARM
8
A Quick Look at Your Keypad
ˆ Preparation
This section gives basic guidelines for
connecting the wires from your alarm
system to the keypad and for assigning
an address to the keypad.
CONNECTING THE KEYPAD
TO YOUR ALARM SYSTEM
1. Route four-conductor cable (not supplied, available at your local
RadioShack store) from the alarm
system to the location where you will
install the keypad.
2. Secure the wires to the keypad by
stripping about 1/2 inch of insulation
from the end of each wire, loosening
the terminal screw, placing the bare
end of the wire under the terminal
clamp, and tightening the screw.
Preparation
9
3. Connect the wires from the keypad
to the alarm system’s terminals as
indicated:
Keypad
Terminal
To 49-459
Terminal
No.
To 49-454
Terminal
No.
POWER
41
9
GND
44
7
DATA1
43
10
DATA2
42
8
10
Preparation
POWER
DATA1
GND
DATA2
ASSIGNING AN ADDRESS
Each installed keypad must have a different address to work with your alarm system. If you are installing only one keypad,
and there are no other keypads already
connected, you do not need to change
the address. If you are installing more
Preparation
11
than one keypad, or there is already a
keypad installed, follow these steps to
change the keypad address.
1. If there are other keypads installed
(including the keypad supplied with
the system), remove the installed
keypads and note the position of the
two DIP switches on their back panels.
DIP Switches
2. Use a sharp object (such as the tip of
a pen) to set the DIP switches on
each new keypad so no two keypads
have the same setting. There are
four possible settings for each keypad, as shown in the following chart.
12
Preparation
Keypad
Number
Address 1
Address 2
1
Off
Off
2
On
Off
3
Off
On
4
On
On
TESTING THE CONNECTION
After following the steps in “Connecting
the Keypad to Your Alarm System” on
Page 9 and “Assigning an Address” on
Page 11, follow the instructions in your
alarm system’s owner’s manual to arm
and disarm the system using the keypad.
After you confirm proper operation, disconnect the cable from both the alarm
system and the keypad.
Preparation
13
INSTALLING THE KEYPAD
Note: Install the keypad indoors away
from dust, dirt, and temperature or humidity extremes.
1. Select a location on the wall that is
not directly over a wall stud. An electronic wall stud finder is available at
your local RadioShack store.
2. Using a single-gang electrical box as
a template, cut a hole in the wall the
same size as the box.
3. Route connection wires from the
alarm system to the hole (through
the attic, walls, and so on) and
through the knock-out plug in the
electrical box. Leave at least 6
inches of extra wire for connection to
the keypad.
14
Preparation
4. Insert the box into the hole and nail it
to the wall stud or use metal strips
designed for mounting an electrical
box in wallboard. The box should be
recessed slightly behind the surface
of the wall.
5. Connect the wires to the keypad and
the alarm system terminals according to the chart in “Connecting the
Keypad to Your Alarm System” on
Page 9.
6. Press the button on the bottom of the
keypad, then remove the keypad’s
front cover.
7. Secure the keypad to the box using
the supplied screws. Then replace
the keypad’s front cover.
Preparation
15
ˆ Operation
SETTING THE SECURITY
CODE
The 49-454 or 49-459 security system
lets you store one security code.
1. If the alarm system is armed, disarm
it by entering the current four-digit
personal security code. (If this is the
first time you have turned on the system, the security code is the system’s default code.) ARMED on the
keypad turns off.
2. Hold down SETUP for 2 seconds.
Both ARMED and READY flash
slowly.
3. Enter the current security code. Both
ARMED and READY flash rapidly.
16
Operation
4. Enter a new security code. Both
ARMED and READY turn off.
5. Enter the new security code again to
confirm. If you entered the correct
code, READY flashes three times
and the system returns to standby
mode.
If you entered the wrong code,
ARMED flashes three times and the
system returns to standby mode.
Start again from Step 1.
Notes:
• If you take longer than 30 seconds to
complete Step 3, 4, or 5, the keypad
automatically resets to the old code.
Begin again from Step 2.
• If other keypads are installed, the
alarm system does not respond to
Operation
17
any keys from those keypads for 10
seconds after the last keypress on
the new keypad.
• While entering the security code, if
you enter an incorrect digit before
entering the last digit, press CANCEL
to cancel the previous entries, then
enter the security code again.
ARMING/DISARMING THE
ALARM
To arm the system, enter the security
code then press ARM. Or, press ARM
twice. ARMED lights. To disarm the system, enter the security code. ARMED
turns off.
Note: If you enter the wrong security code
three times in a row, the alarm system
locks out all keypads for about 5 minutes.
18
Operation
USING ANNUNCIATE MODE
Annunciate mode lets you set the alarm
system so it sounds a brief pre-alarm if it
detects any change in the assigned zone.
1. If the system is disarmed and no
zone is violated, hold down SETUP
for about 2 seconds. ARMED and
READY flash slowly.
2. Enter the current security code
within 30 seconds. ARMED and
READY flash rapidly.
3. Press ANNC (annunciate) once.
ARMED and READY turn off.
4. To enable annunciate mode, press
ENTER. READY flashes 3 times. If
the alarm system detects any
change in the assigned zone, it
sounds a brief pre-alarm.
Operation
19
To disable annunciate mode, hold
down SETUP for about 2 seconds.
ARMED and READY flash slowly.
Enter the security code, press ANNC,
then press CANCEL. READY flashes
3 times.
UNDERSTANDING
ARMED AND READY
Note: A loop is an electrical circuit consisting of one or more sensors connected
in series or parallel.
ARMED
READY
Off
Off
1. System is disarmed, loop is violated (broken).
2. SETUP mode.
On
On
System is armed,
loop is OK.
20
Meaning
Operation
ARMED
READY
Meaning
On
Flashing
Exit or entry delay
is counting.
Off
On
System is disarmed, loop is OK.
Flashing
slowly
Flashing
slowly
System is in setup
mode.
Flashing
Off
Loop is violated in
armed mode and
the alarm
sounded.
Flashing
On
Loop is violated in
armed mode or
the panic alarm
sounded.
Flashing
alternately
Flashing
alternately
Communication
between the alarm
and keypad is broken.
Operation
21
Note: If the alarm sounded while you
were away, ARMED flashes. Enter the
security code then press CANCEL to stop
the flashing. See your security system’s
owner’s manual for further information.
TRIGGERING A PANIC
ALARM
You can trigger a panic alarm at any time
by pressing ENTER and CANCEL at the
same time. The system does not have to
be armed to sound the panic alarm.
TESTING THE SYSTEM
Check the system once a week to be
sure it is operating properly. Refer to the
main control unit’s operating instructions
for proper test procedures.
22
Operation
Important: To prevent false alarms when
testing your system, be sure to disconnect security dialers or any other devices
that send a message to a remote location. Because the alarm system sounds
during these tests, be sure to notify your
neighbors and any proper authorities of
the test.
Operation
23
ˆ Troubleshooting
If your keypad does not arm or disarm
your system, be sure that all connections
are correct. Additionally, the security
code might have reset to the factory default if the security system loses AC power. Try the default security code.
If you cannot remember the code, refer to
your security system’s owner’s manual
for instructions on how to reset the factory default code.
ˆ Care
Keep the keypad dry; if it gets wet, wipe it
dry immediately. Use and store the keypad only in normal temperature environments. Handle the keypad carefully; do
24
Troubleshooting
not drop it. Keep the keypad away from
dust and dirt, and wipe it with a damp
cloth occasionally to keep it looking new.
Modifying or tampering with the keypad’s
internal components can cause a malfunction and might invalidate its warranty.
If your keypad is not performing as it
should, take it to your local RadioShack
store for assistance.
Care
25
ˆ Specifications
Operating Voltage..........................10–18 VDC
Current Draw ......15 mA @ 12 VDC (no LEDs)
25 mA @ 12 VDC (one LED)
Operating Range ........................... 32 to 122°F
(0 to 50°C)
Storage Temp........................... –40 to 149°F
(–40° to 65°C)
Dimensions ........... 19/20 × 219/20 × 41/2 inches
(37 × 72 × 115 mm)
Weight ................................................... 105 g
(3.7 oz.)
Specifications are typical; individual units
might vary. Specifications are subject to
change and improvement without notice.
26
Specifications
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for
ninety (90) days from the date of purchase from RadioShack
company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF
THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED
DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE
OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY
DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period,
take the product and the RadioShack sales receipt as proof of
purchase date to any RadioShack store. RadioShack will, at
its option, unless otherwise provided by law: (a) correct the
defect by product repair without charge for parts and labor; (b)
replace the product with one of the same or similar (continued)
Specifications
27
(continued) design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is
made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are
warranted for the remainder of the original warranty period.
You will be charged for repair or replacement of the product
made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by
or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or
other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d)
cosmetic damage; (e) transportation, shipping or insurance
costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor,
Fort Worth, TX 76102
We Service What We Sell
RadioShack Corporation
Fort Worth, Texas 76102
12/99
49-462
AO0038AAA1
10A00
Printed in China
Download PDF