ETS-Lindgren | 3181 | Antenna Mount Guide - ETS

Mounting ETS-Lindgren Antennas
Before mounting an antenna, see Safety Information. For complete safety, regulatory, and
This guide describes the hardware required to mount your ETS-Lindgren antenna to a tripod, mast, or boom,
other product marking information, see the user manual for your ETS-Lindgren antenna.
and is intended to be used in conjunction with the antenna user manual. This guide does not replace the
antenna user manual.
Safety Information
WARRANTY
These antennas and mount destinations are included:
ONLY QUALIFIED PERSONNEL should install, operate, or service this equipment.
CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may void
your warranty. If you attempt to service the unit by yourself, disconnect all electrical power before starting.
There are voltages at many points in the instrument that could, if contacted, cause personal injury.
Only trained service personnel should perform adjustments and/or service procedures upon this instrument.
Capacitors inside this instrument may still be CHARGED even when instrument is disconnected from its power source.
Antenna Type
BiConiLog™ Antennas – 3140B, 3149, 3142C, 3142D, 3142E, 3143B
Biconical Antennas – 3109, 3104C, 3110B, 3110C
Mini-Bicon Antennas – 3180, 3180B, 3181, 3182, 3183, 3184
Log Periodic Antennas – 3144, 3147, 3148, 3148B, 3186
Warranty Information
Double-Ridged Waveguide Horns – 3106B, 3115, 3116, 3116B, 3116C, 3117, 3119
For complete warranty information, see the user manual for your ETS-Lindgren antenna.
3164 Series Horns
– Quad-Ridged Horns (–05, –06, –07, –08, –10, –11)
– Dual-Polarized Horns (–03, –04)
Pyramidal Horn Antennas – 3160 Series, 3161 Series
Dipoles – 3121C, 3121D
Loop Antennas and Rod Antennas – loop antennas, rod antennas
Conical Log Spirals – 3101, 3102, 3103
High Gain Conical Horns – 3163 Series (–03, –04, –05, –06)
Mount Destination
Model 4-TR Tripod – ETS-Lindgren 4-TR tripod
Model 7-TR Tripod Positioner – includes 109042, 108983, 118947, and 108507 booms:
109042 – straight; for general antenna mounting on a 7-TR
108983 – offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization;
USA Headquarters
1301 Arrow Point Drive
Cedar Park, TX 78613
Phone: +1.512.531.6400
support@ets-lindgren.com
118947 – for stinger-type antennas only
Please see www.ets-lindgren.com for a list of all ETS-Lindgren offices.
108507 – for the 3106 and 3106B only
can also be used to mount stinger-type antennas
© Copyright 2008–2013 by ETS-Lindgren Inc. All Rights Reserved. No part of this document may be copied by any means
without written permission from ETS-Lindgren Inc.
Mast – 2070 Series, 2075, and 2175 Antenna Towers
2x2 Boom – typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
The ETS-Lindgren logo and BiConiLog are trademarks of ETS-Lindgren Inc.
399807, Rev G
Revision/Date: A, Initial Release–June, 2008
B, Updates–February, 2009
C, Added mini-bicons, 3301C–November, 2009
D, Updated 3149 mounting, added 3163–March, 2010
E, Added 3116B, 3119, 3164-10–November, 2010
F, Added 3106B mounting info–July, 2013
G, Added 118947, 3116C, 3142E, 3143B, 3164-11, 3180B, 3186–November, 2013
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
BiConiLog™ Antennas
3140B
7-TR, Mast
4-TR
100989 Polarizing
Antenna Adapter (2)
OR
106470 Non-Polarizing
Antenna Adapter (2)
Do not mount
to a 4-TR.
To
antenna
mounting
bracket,
insert
knob
OR
2x2 Boom
100989 Polarizing
Antenna Adapter (2)
OR
106470 Non-Polarizing
Antenna Adapter (2)
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
To
antenna
mounting
bracket,
insert
knob
To
antenna
mounting
bracket,
insert
knob
105861
Thread
Insert
105861
Thread
Insert (2)
104136
Boom
Antenna
Mount
Knob
(2)
Through boom
on 7-TR, Mast
104169
Boom
Antenna
Mount
Knob
(2)
Through boom
on 7-TR, Mast
101913
Fixed
Antenna
Mount
Stinger Mounts
4-TR – Do not mount to
a 4-TR
Notes
7-TR refers to 109042, 108983,
and 118947 booms:
7-TR – Mounts directly to
a 7-TR without additional
hardware
109042 – straight; for general
antenna mounting on a 7-TR
Mast – Additional hardware
required to mount to a mast
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
Standard Parts
Antennas shown here ship with these
standard parts:
105861 Thread Insert
(3140B ships with two)
100989 Polarizing Antenna Adapter
(3140B ships with two)
Insert boom through
Antennas include mounting bracket
(attached) and mounting knob(s)
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
BiConiLog™ Antennas, continued
3149, 3142D/C/E, 3143B
3149
Stinger Mounts
4-TR
100989
Polarizing
Antenna Adapter
OR
101950
Support Rod
To
antenna
mounting
bracket,
insert
knob
To
antenna
mounting
bracket,
insert
knob
3142E
OR
To
antenna
mounting
bracket,
insert
knob
105861
Thread Insert
105861
Thread Insert
101942B
Support
Base
To 4-TR
4-TR – Do not mount to
a 4-TR
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
109042 – straight; for general
antenna mounting on a 7-TR
Mast – Additional hardware
required to mount to a mast
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
Antennas shown here ship with these
standard parts:
To 4-TR
105861 Thread Insert
(3140B ships with two)
100989 Polarizing Antenna Adapter
(3140B ships with two)
Antennas include mounting bracket
(attached) and mounting knob(s)
To 4-TR
7-TR refers to 109042, 108983,
and 118947 booms:
7-TR – Mounts directly to
a 7-TR without additional
hardware
Standard Parts
102308
Swivel
Antenna
Mount
Notes
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
The 3149 can mount directly to a 4-TR.
Use of a 102308 Swivel Antenna Mount
simplifies polarization, and is optional.
3142D
7-TR, Mast
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
OR
2x2 Boom
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
To
antenna
mounting
bracket,
insert
knob
To
antenna
mounting
bracket,
insert
knob
3142C
To
antenna
mounting
bracket,
insert
knob
3143B
104136
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
105861
Thread
Insert
105861
Thread
Insert
104169
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
101913
Fixed
Antenna
Mount
Insert boom through
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Biconical Antennas
3109
4-TR
7-TR, Mast
102308
Swivel Antenna Mount
104169 Boom Antenna
Mount Knob
To
antenna
mounting
hole
Stinger Mounts
2x2 Boom
4-TR – Do not mount to
a 4-TR
106102 Universal
Antenna Mount
To
antenna
mounting
hole
Through boom
on 7-TR, Mast
104136
Boom
Antenna
Mount
Knob
7-TR – Mounts directly to
a 7-TR without additional
hardware
109042 – straight; for general
antenna mounting on a 7-TR
Mast – Additional hardware
required to mount to a mast
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
3110C, 3110B, and 3104C antennas
ship with these standard parts:
100733 Support Rod
101942B Support Base
102108 Clamp Block
Can mount directly to a 4-TR.
Use of a 102308 Swivel Antenna Mount
simplifies polarization, and is optional.
OR
102108
Clamp Block
Antenna
shaft
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
7-TR, Mast
4-TR
102108
Clamp Block
118947 – for stinger-type
antennas only
Standard Parts
Through boom
3110C
7-TR refers to 109042, 108983,
and 118947 booms:
Antenna
balun
To 4-TR
3110C, 3110B, 3104C
Notes
OR
102108
Clamp Block
Antenna
shaft
OR
102108
Clamp Block
Antenna
shaft
2x2 Boom
106102 Universal
Antenna Mount
Antenna
shaft
OR
102108
Clamp Block
102108
Clamp Block
Antenna
shaft
Antenna
shaft
105861
Thread
Insert
105861
Thread
Insert
101913
Fixed
Antenna
Mount
101937
Swivel
Antenna
Mount
Antenna
balun
102308
Swivel
Antenna
Mount
100733
Support Rod
3110B
To 4-TR
To 4-TR
105861
Thread Insert
104169
Boom
Antenna
Mount
Knob
To 4-TR
104136
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
101942B
Support
Base
3104C
105861
Thread Insert
Through boom
on 7-TR, Mast
Insert boom through
Insert boom through
Can mount directly to a 4-TR.
Use of a 102308 Swivel Antenna Mount
simplifies polarization, and is optional.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Mini-Bicon Antennas
3109 3183, 3184
3181,
7-TR, Mast
4-TR
3181, 3184
113956 Antenna
Mount Assembly
113956 Antenna
Mount Assembly
Stinger
To
4-TR for
horizontal
mount
(extension
optional)
3183
113956 Antenna
Mount Assembly
Stinger
For
horizontal
mount
(extension
optional)
Stinger
For vertical
mount place
114669 spacer
over extension
To
4-TR for
vertical
mount
About Mounts
for 3181/3183/3184
2x2 Boom
For
horizontal
mount
(extension
optional)
3181, 3183, and 3184 ship
with 113956 Antenna Mount
Assembly, which includes the
114669 Spacer; no additional
hardware required to mount
to 4-TR
For vertical
mount
Stinger Mounts
Notes
3181, 3183, 3184
7-TR refers to 109042, 108983,
and 118947 booms:
109042 – straight; for general
antenna mounting on a 7-TR
4-TR – See
About Mounts for
3181/3183/3184
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
7-TR, Mast, 2x2 Boom –
Additional hardware
required
3180, 3180B, 3182
118947 – for stinger-type
antennas only
Standard Parts
104169
Boom
Antenna
Mount
Knob
Through boom
3180, 3182
101937
Swivel
Antenna
Mount
3180, 3180B, and 3182
ship with these standard parts:
100733 Support Rod
101942B Support Base
Insert boom through
102108 Clamp Block
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
4-TR / 7-TR – Mounts
directly to a 4-TR or 7-TR
without additional hardware
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
Mast – Additional hardware
required
3180
7-TR, Mast
4-TR
3180 with
mini-cage
elements
3180 with
conical
elements
102108
Clamp Block
OR
102108
Clamp Block
Stinger
102308
Swivel
Antenna
Mount
100733
Support Rod
3180B with
conical
elements
To 4-TR
101942B
Support
Base
3182
To 4-TR
102108
Clamp Block
Stinger
3180B
3180B with
cage
elements
OR
102108
Clamp Block
2x2 Boom
OR
102108
Clamp Block
102108
Clamp Block
Stinger
Stinger
Stinger
105861
Thread Insert
105861
Thread Insert
105861
Thread
Insert
105861
Thread
Insert
104169
Boom
Antenna
Mount
Knob
101913
Fixed
Antenna
Mount
101937
Swivel
Antenna
Mount
To 4-TR
Through boom
on 7-TR, Mast
Insert boom through
Stinger
Insert boom through
Can mount directly to a 4-TR.
Use of a 102308 Swivel Antenna Mount
simplifies polarization, and is optional.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Log Periodic Antennas
3148B
Stinger Mounts
4-TR
100989
Polarizing
Antenna Adapter
OR
101950
Support Rod
To
antenna
mounting
bracket,
insert
knob
To
antenna
mounting
bracket,
insert
knob
To
antenna
mounting
bracket,
insert
knob
105861
Thread
Insert
105861
Thread Insert
101942B
Support
Base
To 4-TR
4-TR – Do not mount to
a 4-TR
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
OR
To 4-TR
Mast – Additional hardware
required to mount to a mast
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
105861 Thread Insert
100989 Polarizing Antenna Adapter
Antennas include mounting bracket
(attached) and mounting knob(s)
To 4-TR
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
Can mount directly to a 4-TR.
Use of a 102308 Swivel Antenna Mount
simplifies polarization, and is optional.
3148
7-TR, Mast
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
3147
109042 – straight; for general
antenna mounting on a 7-TR
Antennas shown here ship with these
standard parts:
3148, 3147, 3144
7-TR refers to 109042, 108983,
and 118947 booms:
7-TR – Mounts directly to
a 7-TR without additional
hardware
Standard Parts
102308
Swivel
Antenna
Mount
Notes
To
antenna
mounting
bracket,
insert
knob
104136
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
OR
2x2 Boom
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
To
antenna
mounting
bracket,
insert
knob
To
antenna
mounting
bracket,
insert
knob
OR
100989 Polarizing
Antenna Adapter
OR
106470 Non-Polarizing
Antenna Adapter
To
antenna
mounting
bracket,
insert
knob
Mounting the Model 3186
105861
Thread
Insert
101913
Fixed
Antenna
Mount
104169
Boom
Antenna
Mount
Knob
Insert boom through
101937
Swivel
Antenna
Mount
For complete information
on mounting the Model 3186,
see the Model 3186 Dual Stacked
Log Periodic Dipole Array (LPDA)
User Manual.
Insert boom through
Through boom
on 7-TR, Mast
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Double-Ridged Waveguide Horns
3106B
4-TR
3115
All Double-Ridged
Waveguide Horns
(except the 3106 Series
and 3119)
mount directly to a 4-TR.
Mounting hardware is
included; no additional
hardware required.
OR
To
antenna
mounting
hole
To
antenna
mounting
hole
Do not mount the
3106 Series or 3119
to a 4-TR.
Stinger Mounts
2x2 Boom
2x2 Boom
7-TR, Mast
104169
Boom
Antenna
Mount
Knob
101913
Fixed
Antenna
Mount
7-TR – Mounts directly to
a 7-TR without additional
hardware
101937
Swivel
Antenna
Mount
Mast – Additional hardware
required to mount to a mast
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
2
3116B
Remove wingnut, nuts,
and screws from
mount adapter;
will re-use screws
in step 4.
3116
Mount 3106B to 108507 Boom
Note: Install the 108507 boom onto the 7-TR before
performing these steps. For clarity, the 7-TR
is not shown in the following illustrations.
1
3116C
Remove
104136 knobs
and lift
mount adapter
from boom;
will re-use in
step 5.
3117
109042 – straight; for general
antenna mounting on a 7-TR
(for 3106 Series only) 108507 –
centerline rotation boom;
when changing polarization,
maintains centerline rotation
See Mount 3106B to
108507 Boom
for the steps to mount
a 3106 Series antenna
to a 7-TR.
3116, 3116B, 3116C
7-TR refers to these booms:
Insert boom through
Insert boom through
Through boom
on 7-TR, Mast
4-TR – Do not mount to
a 4-TR
To
antenna
mounting
hole
Notes
4
Re-insert/tighten screws through vertical part
of mount adapter into two holes on antenna.
Re-insert/tighten screw through horizontal part
of mount adapter into mount block on antenna.
3119
3
Remove
screws from
side of 3106B
with antenna
connector.
5
Re-insert/tighten
104136 knobs
to attach antenna and
mount adapter to boom.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
3164 Series Horns
Open Boundary
Quad-Ridged Horns
3164-05, -06, -07, -08, -10, -11
3164-06
3164-11
OR
Bracket Mount
To
antenna
mounting
hole
Only the 3164-05
(108071 bracket)
and 3164-11
(119430 bracket)
can be mounted
to a 4-TR.
3164-05
3164-07
7-TR, Mast
4-TR
Do not mount
3164-06, -07,
-08, or -10
antennas to a 4-TR.
Bracket Mount
3164-10
Through boom
on 7-TR, Mast
3164-08
To
antenna
mounting
hole
105861
Thread
Insert
105861
Thread
Insert
104169
Boom
Antenna
Mount
Knob
101913
Fixed
Antenna
Mount
Insert boom through
Through boom
on 7-TR, Mast
For the type of bracket mount,
see Standard Parts.
4-TR
106974 Mount
7-TR, Mast
2x2 Boom
106974 Mount
106974 Mount
To
antenna
mounting
hole
To
antenna
mounting
hole
7-TR refers to 109042, 108983,
and 118947 booms:
109042 – straight; for general
antenna mounting on a 7-TR
Mast – Additional hardware
required to mount to a mast
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
118947 – for stinger-type
antennas only
108071 Mount – ships with
3164-05
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
106974 Mount – ships with
3164-06, 3164-07, 3164-08,
and 3164-10
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
119430 Mount – ships with
3164-11
105861 Thread Insert – ships
with 3164-08 and 3164-10
About 3164 Mounts
3164-05 – ships with
stinger for stinger-compatible
mounts
To
antenna
mounting
hole
105861
Thread
Insert
Notes
7-TR – Mounts directly to
a 7-TR without additional
hardware
Standard Parts
For the type of bracket mount, see Standard Parts.
Dual-Polarized Horns
3164-03, -04
4-TR – Do not mount to
a 4-TR
Bracket Mount
To
antenna
mounting
hole
104136
Boom
Antenna
Mount
Knob
See About 3164 Mounts.
Stinger Mounts
2x2 Boom
3164-05, -11 – ships with
mounting hardware, no
additional hardware required
to mount to 4-TR, 7-TR,
mast, or 2x2 boom
105861
Thread
Insert
104136
Boom
Antenna
Mount
Knob
101913
Fixed
Antenna
Mount
To 4-TR
Through boom
on 7-TR, Mast
Insert boom through
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Pyramidal Horn Antennas
3160 Series, 3161 Series
4-TR
Pyramidal horn antennas
mount directly to a 4-TR;
no additional hardware
required.
Do not mount 3160-01,
3160-02, and 3161-01
antennas to a 4-TR.
OR
To
antenna
mounting
hole
To
antenna
mounting
hole
104169
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
About 3160 Mounts
2x2 Boom
2x2 Boom
7-TR, Mast
101913
Fixed
Antenna
Mount
Insert boom through
3160-09 and 3160-10 –
ship with a supplemental
mount that may be used
with the 4-TR, 7-TR, mast,
and 2x2 boom
To
antenna
mounting
hole
101937
Swivel
Antenna
Mount
Insert boom through
Notes
4-TR: Do not mount large pyramidal
horn antennas to a 4-TR.
7-TR refers to 109042, 108983,
and 118947 booms:
109042 – straight; for general
antenna mounting on a 7-TR
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
See About 3160 Mounts.
See About 3160 Mounts.
See About 3160 Mounts.
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Dipoles
3121D
Stinger Mounts
4-TR
102108
Clamp Block
102108
Clamp Block
OR
Antenna
shaft
OR
Antenna
shaft
Antenna
shaft
102308
Swivel
Antenna
Mount
100733
Support Rod
Stinger
4-TR – Do not mount to
a 4-TR
102108
Clamp Block
105861
Thread Insert
7-TR refers to 109042, 108983,
and 118947 booms:
7-TR – Mounts directly to
a 7-TR without additional
hardware
109042 – straight; for general
antenna mounting on a 7-TR
Mast – Additional hardware
required to mount to a mast
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
Standard Parts
118947 – for stinger-type
antennas only
To 4-TR
To 4-TR
3121C
Notes
Antennas shown here ship with these
antenna adapters:
100733 Support Rod
101942B
Support
Base
101942B Support Base
102108 Clamp Block
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
Can mount directly to a 4-TR.
Use of a 102308 Swivel Antenna Mount
simplifies polarization, and is optional.
To 4-TR
7-TR, Mast
OR
102108
Clamp Block
2x2 Boom
106102 Universal
Antenna Mount
Antenna
shaft
OR
102108
Clamp Block
102108
Clamp Block
Antenna
shaft
Antenna
shaft
105861
Thread
Insert
105861
Thread
Insert
101913
Fixed
Antenna
Mount
101937
Swivel
Antenna
Mount
Antenna
balun
105861
Thread Insert
104169
Boom
Antenna
Mount
Knob
104136
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
Through boom
on 7-TR, Mast
Insert boom through
Insert boom through
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Loop Antennas and Rod Antennas
Loop Antennas
4-TR
Loop antennas and
rod antennas mount
directly to a 4-TR;
no additional hardware
required.
OR
To
antenna
mounting
hole
To
antenna
mounting
hole
104169
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
About 3301C
2x2 Boom
2x2 Boom
7-TR, Mast
101913
Fixed
Antenna
Mount
Insert boom through
4-TR Light Tripod – To
comply with the
MIL-STD-461F standard,
a smaller tripod (4-TR,1ML)
is available (optional).
To
antenna
mounting
hole
101937
Swivel
Antenna
Mount
Insert boom through
MIL-STD-461F Kit – To
comply with the standard,
a cable and grounding
kit (113359) is included
with the 3301C.
Notes
7-TR refers to 109042, 108983,
and 118947 booms:
109042 – straight; for general
antenna mounting on a 7-TR
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
Rod Antennas
3301C
See About 3301C.
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
Conical Log Spirals
3101
4-TR
7-TR, Mast
Notes
2x2 Boom
7-TR refers to 109042, 108983,
and 118947 booms:
109042 – straight; for general
antenna mounting on a 7-TR
Conical log spirals mount
directly to a 4-TR;
no additional hardware
required.
Conical log spirals
mount directly to a 7-TR.
Mounting hardware is
included; no additional
hardware required.
Conical log spirals
not intended
for 2x2 boom.
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
Standard Parts
101942B Support Base – ships
with 3101, 3102, and 3103
3102
101941 Support Rod
with 3101
– ships
101943B Support Rod
with 3102
101944 Support Rod
with 3103
– ships
– ships
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
3103
www.ets-lindgren.com
Mounting ETS-Lindgren Antennas
High Gain Conical Horns
3163 Series
-03, -04, -05, -06
4-TR
OR
To
antenna
mounting
hole
To
antenna
mounting
hole
About 3163 Series
2x2 Boom
2x2 Boom
7-TR, Mast
To
antenna
mounting
hole
Each Model 3163 Series
includes a built-in
1/4–20 thread mount.
3163-03
3163-04
3163-05
3163-06
Model 3163 Series
horn antennas
mount directly to a 4-TR;
no additional hardware
required.
104169
Boom
Antenna
Mount
Knob
Through boom
on 7-TR, Mast
101913
Fixed
Antenna
Mount
Insert boom through
101937
Swivel
Antenna
Mount
Insert boom through
The backplate on each
Model 3163 Series provides
threaded holes for
mounting directly into the
feed section of
a tapered chamber.
Additionally, you can use
the threaded holes
to create your own custom
mounting solution. See the
3163 manual for a diagram
of each backplate.
Notes
7-TR refers to 109042, 108983,
and 118947 booms:
109042 – straight; for general
antenna mounting on a 7-TR
108983 – offset; for general
antenna mounting on a
7-TR with pneumatic or manual
polarization; can also be used
to mount stinger-type antennas
118947 – for stinger-type
antennas only
Mast refers to 2070 Series, 2075,
and 2175 Antenna Towers
2x2 Boom refers to a typical
2-inch by 2-inch boom;
non-ETS-Lindgren and previous
generation EMCO positioning systems
www.ets-lindgren.com
Download PDF