Digital Monitoring | XR5 | Installation guide | Digital Monitoring XR5 Installation guide

XR5FC/XR5SL Commercial Fire Panels
Installation Guide
5 Zone Fire and Slave Panels with Built-in Communicators
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
LT-0299 (7/96)
MODELS XR5FC AND XR5SL
COMMERCIAL FIRE PANELS
INSTALLATION GUIDE
FCC NOTICE
This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance with
the manufacturer's instructions, may cause interference with radio and television reception. It has been type tested and
found to comply with the limits for a Class B computing device in accordance with the specification in Subpart J of Part 15
of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment
off and on, the installer is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the compute into a different outlet so that computer and receiver are on different branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.
The installer may find the following booklet, prepared by the Federal Communications Commission, helpful:
"How to identify and Resolve Radio-TV Interference Problems."
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402
Stock No. 004-000-00345-4
Copyright © 1996 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
TABLE OF CONTENTS
Section
Page
Panel Specifications
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Power supply ......................................................................................................................... 1
Communication ..................................................................................................................... 1
Panel zones ........................................................................................................................... 1
Remote Annunciators (Alphanumeric or LED Keypads) ....................................................... 1
Auxiliary Outputs ................................................................................................................... 1
Push button reset .................................................................................................................. 1
Enclosure specifications ........................................................................................................ 1
Introduction
2.1
2.2
2.3
2.4
Description ............................................................................................................................ 1
Before you begin ................................................................................................................... 2
About this guide ..................................................................................................................... 2
How to use this guide ............................................................................................................ 2
System Components
3.1
3.2
3.3
3.4
3.5
Description ............................................................................................................................ 3
XR5FC Wiring diagram ......................................................................................................... 3
XR5SL Wiring diagram .......................................................................................................... 4
Lightning protection ............................................................................................................... 4
Security Command® keypads ............................................................................................... 4
Installation
4.1
4.2
4.3
4.4
Mounting the enclosure ......................................................................................................... 5
Model 377 Trouble Annunciator Module ................................................................................ 5
Mounting keypads ................................................................................................................. 6
Wiring keypads ...................................................................................................................... 6
Primary Power Supply
5.1 Terminals 1 and 2 .................................................................................................................. 6
Secondary Power Supply
6.1
6.2
6.3
6.4
6.5
6.6
Battery terminals 3 and 4 ....................................................................................................... 7
Earth ground .......................................................................................................................... 7
Replacement period .............................................................................................................. 7
Discharge/recharge ............................................................................................................... 7
Battery supervision ................................................................................................................ 7
XR5FC and XR5SL power requirements ............................................................................... 8
Bell Output
7.1 Terminal 5 (XR5FC Only) ...................................................................................................... 8
4-Wire Smoke Detector Power
8.1 Terminal 6 (XR5FC Only) ...................................................................................................... 8
Keypad Data Bus
9.1
9.2
9.3
9.4
9.5
Description ............................................................................................................................ 9
Terminal 7 - RED ................................................................................................................... 9
Terminal 8 - YELLOW ............................................................................................................ 9
Terminal 9 - GREEN .............................................................................................................. 9
Terminal 10 - BLACK ............................................................................................................. 9
Class A (Style D) Fire Zone
10.1 Description .......................................................................................................................... 9
TABLE OF CONTENTS
Section
Page
Class B (Style A) Fire Zones
11.1
11.2
11.3
11.4
Description ........................................................................................................................... 9
Operational parameters ....................................................................................................... 9
Zone response time ........................................................................................................... 10
Compatible 2-wire smoke detectors .................................................................................. 10
Form C Relay Outputs
12.1 Description ........................................................................................................................ 10
Annunciator Outputs
13.1 Description ........................................................................................................................ 10
13.2 Harness wiring ................................................................................................................... 10
Telephone RJ Connector
14.1 Description .........................................................................................................................11
14.2 FCC registration ................................................................................................................. 11
14.3 Notification ..........................................................................................................................11
Reset Jumpers
15.1 Description .........................................................................................................................11
Silence/Reset button
16.1 Silence/Reset button .......................................................................................................... 11
Dual Phone Line Connectors
17.1 Description .........................................................................................................................11
Universal UL and NFPA Fire Alarm Specifications
18.1
18.2
18.3
18.4
18.5
18.6
Introduction ........................................................................................................................ 12
Wiring ................................................................................................................................ 12
Police station phone number ............................................................................................. 12
System maintenance ......................................................................................................... 12
Audible alarm (XR5FC only) .............................................................................................. 12
UL Listed Receivers .......................................................................................................... 12
UL 864 NFPA 72 Specifications
19.1
19.2
19.3
19.4
Power Fail delay ................................................................................................................
Central Station Signaling Systems ....................................................................................
Local Protective Signaling Systems ..................................................................................
Remote Station Protective Signaling Systems ..................................................................
12
12
12
12
California State Fire Marshal Specifications
20.1
21.1
21.2
21.3
21.4
21.5
21.6
Bell output definition .......................................................................................................... 12
Multiple 866 Notification Circuit Modules .......................................................................... 13
Multiple 865 Notification Circuit Modules .......................................................................... 14
Multiple 866 Notification Circuit Modules for zoned annunciation ..................................... 15
Remote Station reversing relay connection ....................................................................... 16
Supervised remote relay .................................................................................................... 17
XR5SL Connection to FACP .............................................................................................. 18
Introduction
Panel Specifications
1.1
Power supply
Primary Power Input: 16.5 VAC 40VA (Model 320 wire-in) or 12/24 VDC from Fire Alarm Control Panel (FACP)
Standby Batteries: One or two 12 VDC 7.0Ah
Auxiliary Output: 500mA at 12 VDC
Bell Output: 1.5 Amps at 12 VDC (XR5FC only)
Smoke Detector Output: 100mA at 12 VDC (XR5FC only)
All circuits inherent power limited except the red battery wire.
1.2
Communication
Built-in SDLC Digital Dialer communication to DMP Model SCS-1 Receivers.
Built-in 4-2 communication to non-DMP receivers.
Can operate as a local system (XR5FC only).
1.3
Panel zones
One Class A (Style D) zone (terminals 11 to 14).
Four 3.3K Ω EOL Class B (Style A) powered fire zones with reset capability (terminals 15 to 22).
1.4
Remote Annunciators (Alphanumeric or LED Keypads)
You can connect alpha Security Command keypads and LED keypads to the XR5FC and XR5SL keypad data
bus. The panels do not support zone expansion on the bus.
1.5
Auxiliary Outputs
Two Form C (SPDT) outputs (Outputs 1 and 2). Each output requires one Model 305 plug-in relay. Each relay is
rated for 1 Amp at 30 VDC.
Four open collector annunciator outputs (Outputs 1 to 4). No relay is required. Each output is rated for 50mA at
30 VDC resistive.
1.6
Push button reset
The XR5FC and XR5SL panels each provide a push button mounted on the printed circuit board that allows
authorized users to reset latch detectors and silence active alarm bell ouputs. See section 16.1.
1.7
Enclosure specifications
The XR5 panels are shipped in an enclosure with end of line resistors, battery leads, user's guide, and
programming sheet.
XR5FC
Size:
Weight:
Color:
Construction:
XR5SL
12.5" W x 9.5" H x 3.75" D
4 lbs
Red
20 gauge cold rolled steel
Size:
Weight:
Color:
Construction:
12.5" W x 9.5" H x 2.75" D
4 lbs
Red
20 gauge cold rolled steel
Introduction
2.1
Description
The DMP XR5FC and XR5SL Commercial Fire Panels are powerful 12 VDC fire alarm communicators with
battery backup that can also be powered from the12 or 24 VDC auxiliary output of a Fire Alarm Control Panel
(FACP). Each panel provides one Class A (Style D) fire zone and four Class B (Style A) powered fire zones with
reset capability for 2-wire smoke detectors, relays, or other latching devices.
The XR5 panels can communicate to one or two DMP SCS-1 Receivers using SDLC digital dialer or to one or
two non-DMP receivers using the 4-2 reporting format.
XR3F/XR5F Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 1
Introduction
2.2
Before you begin
Before installing the XR5, we recommend you read through the entire contents of this guide. Familiarize yourself
with the features of the panel and the key points to remember during the installation. Be sure to read and
understand all of the caution statements printed in bold italics.
In addition to this installation guide, you should also read through and familiarize yourself with these other
product documents:
• XR5 Programming Guide (LT-0312)
• XR5 User's Guide (LT-0296)
• XR5 Program Information Sheet (LT-0297)
2.3
About this guide
The information contained in this guide is organized into three sections: Table of Contents, Introduction, and
Installation.
• The Table of Contents at the front of this guide lists all of the headings and subheadings used throughout
each section. To the right of each heading is the section number where the information can be found.
• The Introduction section gives you an overview of the various components that go into an XR5 system
and diagrams some typical system configurations. This section gives descriptions of the panel, keypads,
and accessory modules and provides details on how each of them operate together in the system.
• The Installation section begins with mounting instructions for the enclosure and takes you through the
proper way to power up the panel prior to programming.
Caution notes
Throughout this guide you'll see caution notes containing information you need to know when installing the XR5
panels. These cautions are written in bold italics and are followed by a detailed description of the caution. See
the example shown below:
Always ground the panel before applying power to any devices: The XR5 panels must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects against
Electrostatic Discharge (ESD) that can damage system components.
Whenever you see a caution note, make sure you completely read and understand its information. Failing to
follow the caution note can cause damage to the equipment or improper operation of one or more components in
the system.
2.4
How to use this guide
To locate information about installing the XR5 panels, first go to the Table of Contents at the front of this guide.
Find the subject heading that closely describes the information you need and turn to the section number shown
to the right of the heading.
The text that follows the heading has been written to provide as much information about the subject as possible.
If you can't find the information you need under that heading, try scanning through a few of the headings before
and after and reading the text under those that sound similar.
XR3F/XR5F Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 2
Introduction
System Components
3.1
Description
A basic XR5 system is made up of the alarm panel with built in communicator, an enclosure, a 16.5 VAC wire-in
transformer, and a 12 VDC 7.0Ah battery. You can add up to two alphanumeric Security Command keypads and
one LED Security Command keypad to the panel and also connect control and annunciating devices to the
panel's Form C and annunciator outputs. Refer to section 6.6 in this guide when calculating power requirements.
3.2
XR5FC Wiring diagram
The XR5FC system below shows some of the accessory devices you can connect for use in various
applications.
377 Trouble Annunciator Module
Refer to the Model 377 Installation
Instructions (LT-0314).
MODEL XR5
SILENCE/RESET
PUSH FOR ONE SECOND
J5
Silence/Reset
Header
Silence/Reset
Button
Telephone Connections
Wiring on
terminals 5
through 22 must
exit to the right
and maintain a
1/4" separation
from the AC and
battery positive
wiring.
DMP transformer
Model 320
16.5 VAC 40VA
wire-in
J10 Trouble Annunciator Header
Relay Sockets for Optional
Form C Outputs on J11
OUTPUT 1
Direct connect to unswitched
120 VAC 60 Hz
Panel Reset
PANEL
RESET
OUTPUT 2
MAIN BACKUP
J4
1
2
3
4
J11
AC
4
B+
5
B–
7
6
8
BELL SMK RED
9
10
S
S
10k Ω
Model 308
All modules must be installed in
an approved enclosure within 20
feet and connected by conduit.
14
S
W
16
15
Z2+
17
Z2 –
S
S
Z3+
S
18
Z3 –
S
19
Z4+
S
20
21
Z4 –
S
S
S
J12
Output Header J12
Four Open Collector Outputs.
Use Model 300 Harness.
50mA at 30 VDC resistive
Output 1
S
For sprinkler
supervision, Normally
Open devices must be
used.
S
S
Output 2
Output Header J11
Two Form C (SPDT) Outputs.
3.3k Ω
ZONE 2
Up to 100mA of current is
available for 4-wire smoke
detectors from terminal 6.
Smoke
Detector
Smoke
Detector
–+
–+
3.3k Ω
ZONE 4
Red
Power
Supervision
Relay
Black
Heat detectors, pull stations,
or any other contact devices
listed for Fire Protective
Signaling can be connected to
zones 1 to 5.
S
N/C COM N/O N/C COM N/O
S
3.3k Ω
S = Supervised Circuit
S
Z5 –
S
W
ZONE 1
S S
Aux. Power
Ground
Alarm Input
Bell Input
Bell Out Pos
Bell Out Neg
Bell Trouble
Bell Trouble
Z5+
22
ZONE 5
Bell Circuit
1.5 Amps at 12 VDC
Minimum cutoff time 5
minutes
Model 866
13
S
BLACK
GREEN
22 GA. MIN
22 GA. MIN
YELLOW
RED
Cold Water Pipe
Earth Ground
Class B (Style W)
Notification Circuit Module
37mA at 12 VDC
12
S
22 GA. MIN
Maximum AC wire distance
With 16 gauge wire: 70 feet
With 18 guage wire: 40 feet
11
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
S
16 to 18 gauge wire
RED
Secondary Power Supply
1.2 Amps max. charging current.
Use only 12 VDC rechargable
batteries. DMP Model 367.
Replace every 3 to 5 years.
AC
3
22 GA. MIN
S
2
BLACK
S
1
All outputs must be
connected to devices
located within the same
room as the panel.
Zones 2 to 5 compatibility
identifier: A
Maximum operating range:
8.8 VDC to 14.2 VDC.
Refer to LT-0164 for a list of approved
4-wire smoke detectors and power
supervision relays.
See section 11.4 in the XR5FC
Installation Guide (LT-0299) for a list
of approved 2-wire smoke detectors.
3.3k Ω
ZONE 3
Model 692F
40mA at 8 to 16 VDC.
Models 670
100mA at 8 to 16 VDC (125mA with display lit).
Keypads
Models 690
100mA at 8 to 16 VDC.
Up to two alpha keypads
and one LED keypad can be
connected to the XR5FC.
Up to 500mA auxiliary
current at 12 VDC from
Terminal 7.
32-Character Keypads
10 Zone LED Keypads
16-Character Keypads
Figure 1: XR5FC wiring diagram
XR3F/XR5F Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 3
Introduction
3.3
XR5SL Wiring diagram
The XR5SL system below shows some of the accessory devices you can connect for use in various applications.
377 Trouble Annunciator Module
Refer to the Model 377 Installation
Instructions (LT-0314).
MODEL XR5
SILENCE/RESET
PUSH FOR ONE SECOND
J5
Silence/Reset
Header
Silence/Reset
Button
Telephone Connections
Wiring on
terminals 5
through 22 must
exit to the right
and maintain a
1/4" separation
from the AC and
battery positive
wiring.
DMP transformer
Model 320
16.5 VAC 40VA
wire-in
J10 Trouble Annunciator Header
Relay Sockets for Optional
Form C Outputs on J11
OUTPUT 1
Direct connect to unswitched
120 VAC 60 Hz
Panel Reset
PANEL
RESET
All outputs must be
connected to devices
located within the same
room as the panel.
OUTPUT 2
MAIN BACKUP
J4
1
2
3
4
J11
7
4
8
RED
B–
9
10
11
12
S
S
RED
GREEN
BLACK
22 GA. MIN
22 GA. MIN
S
16
15
14
S
W
S
Cold Water Pipe
Earth Ground
13
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
YELLOW
Maximum AC wire distance
With 16 gauge wire: 70 feet
With 18 guage wire: 40 feet
3
B+
22 GA. MIN
2
AC
22 GA. MIN
Secondary Power Supply
1.2 Amps max. charging current.
Use only 12 VDC rechargable
batteries. DMP Model 367.
Replace every 3 to 5 years.
1
AC
16 to 18 gauge wire
RED
S
BLACK
S
Z2+
S
M
S
18
17
Z2 –
S
Z3+
S
20
19
Z3 –
S
Z4+
Z4 –
S
S
S
21
Z5+
22
Z5 –
S
H
N/C COM N/O N/C COM N/O
J12
S
Output Header J12
3.3k Ω
Four Open Collector Outputs.
Use Model 300 Harness.
50mA at 30 VDC resistive
ZONE 5
W
ZONE 1
For sprinkler
supervision,
Normally Open
devices must be
used.
M
S
M
3.3k Ω
3.3k Ω
3.3k Ω
Output 1
Output 2
Output Header J11
Two Form C (SPDT) Outputs.
ZONE 2 ZONE 3 ZONE 4
Heat detectors, pull stations, or any other contact devices
listed for Fire Protective Signaling can be connected to
zones 1 to 5.
Zones 2 to 5 compatibility identifier: A
Maximum operating range:
8.8 VDC to 14.2 VDC.
Keypads
S = Supervised Circuit
Model 670
100mA at 8 to 16 VDC
(125mA with display lit).
Up to 500mA auxiliary
current at 12 VDC from
Terminal 7.
See section 11.4 in the XR5SL
Installation Guide (LT-0299) for a list
of approved 2-wire smoke detectors.
16-Character Keypads
Model 692F
40mA at 8 to 16 VDC.
Model 690
100mA at 8 to 16 VDC.
LED Keypads and up to two
alpha keypads can be
connected to the XR5SL.
32-Character Keypads
10-Zone LED Keypads
Figure 2: XR5SL wiring diagram
3.4
Lightning protection
Metal Oxide Varistors and Transient Voltage Suppressors on the panel help protect against voltage surges on
input and output circuits of the XR5 panels. Additional surge protection is available by installing the DMP 370 or
370RJ Lightning Suppressors.
3.5
Security Command® keypads
You can connect the Models 670, 690, 692F, 770, 771, or 790 Security Command keypads to the 4-wire keypad
data bus provided by the panel on terminals 7, 8, 9, and 10.
XR3F/XR5F Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 4
Installation
Installation
4.1
Mounting the enclosure
The metal enclosure for the XR5FC and XR5SL panels must be mounted in a secure, dry place to protect the
panels from damage due to tampering or the elements. It is not necessary to remove the XR5FC or XR5SL PC
board when installing the enclosure.
Dual 3/4" x 1/2" Knockout
Dual 3/4" x 1/2" Knockout
MODEL XR5
MAIN BACKUP
MODEL XR5
MAIN BACKUP
SILENCE/RESET
PUSH FOR ONE SECOND
J5
J4
PANEL
RESET
SILENCE/RESET
PUSH FOR ONE SECOND
J5
J4
PANEL
RESET
Telephone Connections
Telephone Connections
U21
2
AC
3
B+
4
B–
5
6
7
BELL SMK RED
8
9
10
11
12
13
14
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
16
15
Z2+
Z2 –
18
17
Z3+
Z3 –
19
Z4+
20
Z4 –
21
Z5+
22
Z5 –
N/C COM N/O N/C COM N/O
OUTPUT 2
1
2
3
4
OUTPUT 1
OUTPUT 2
J11
1
AC
EPROM Socket
EPROM Socket
OUTPUT 1
U21
J11
J12
1
2
AC
AC
3
B+
4
B–
5
7
6
BELL SMK RED
Two 1 3/4" Wire Openings
8
9
10
11
12
13
16
15
14
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
Z2+
Z2 –
17
Z3+
18
Z3 –
19
Z4+
20
Z4 –
21
Z5+
22
Z5 –
N/C COM N/O N/C COM N/O
1
2
3
4
J12
1 3/4" Wire Opening
Dual 3/4" x 1/2" Knockouts
Dual 3/4" x 1/2" Knockouts
Extra Deep 3 3/4" Cabinet
Figure 3A: XR5FC in standard Model 340FC enclosure.
4.2
Figure 3B: XR5SL in standard Model 340SL enclosure.
Model 377 Trouble Annunciator Module
The 377 module is installed on the enclosure door and connects to the panel through a 4-wire harness supplied
with the module. See Figure 4.
377 module operation
The 377 Trouble Annunciator Module provides visual
and audible annunciation of System Okay,
communication trouble, and panel processor failure. The
module contains a Green LED for System Okay, a
Yellow LED for Trouble, an electronic sounder, and a
Silence switch.
Communication trouble
If either phone line connected to the panel is in a bad
condition, or if the panel has made TEN failed attempts
to send a report to the central station receiver, the 377
module emits a steady audible alert and turns on the
Yellow LED. The Silence switch can be used to turn off
the sounder only.
Green SYSTEM OKAY LED
SILENCE switch
Yellow TROUBLE LED
Alert sounder
RESET
J9 Command Processor Reset
U21
J10 Trouble Annunciator Header
EPROM Socket
System Okay
When both phone lines are normal and the panel
processor is operating, only the Green LED on the 377
module is on. This LED goes off during a Sensor Reset.
377 Trouble Annunciator Module
(Enclosure door mounted)
Relay Sockets for Optional
Form C Outputs on J11
K4
K5
J11
N/C COM N/O N/C COM N/O
1
2
3
4
J12
Figure 4: 377 module wire harness
Panel processor failure
During a processor failure on the panel, or a remote programming session, the 377 module emits a steady
audible alert and turns on the Yellow LED. The Silence switch will not turn off the sounder or Yellow LED
during these conditions.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 5
Installation
4.3
Mounting keypads
Security Command keypads have removable covers that allow you to easily mount the base to a wall or other
flat surface. After installing the keypad mounting anchors and bringing the keypad wiring from the panel through
the wall, mount the base and connect the keypad wire harness leads to the keypad wiring. Next, attach the
keypad wire harness connector to the pin connector on the keypad circuit board and install the cover.
For mounting keypads on masonry walls, or for applications where conduit is required, use an appropriate DMP
keypad conduit backbox.
4.4
Wiring keypads
Keypad data bus
The keypad data bus consists of a 4-wire cable that provides
12 VDC power, data in, data out, and a panel common. You can
connect keypads in parallel on one 4-wire cable or provide a
separate cable run back to the panel for each keypad. The
maximum cable length for one keypad can be up to 500 feet
using 22 gauge wire or up to 1000 feet using 18 gauge wire.
Refer to the wiring diagram in this guide for additional wiring
information. See section 3.2.
In all applications where more than
one wire is under a terminal, the
wire must be cut and not looped
around the screw terminal.
Figure 5: Proper wiring connections
Primary Power Supply
5.1
Terminals 1 and 2
AC transformer input
Connect the wires from the Model 320, 16.5 VAC 40VA transformer to terminals 1 and 2 on the panel. Use no
more than 70 ft. of 16 gauge or 40 ft. of 18 gauge wire between the transformer and the XR5FC or XR5SL panel.
The transformer provides up to 500mA of auxiliary current for the XR5FC and XR5SL panels. The total current
available is limited by the total battery standby requirements of the installation. See section 6.6 for standby
battery calculations.
The transformer requires an unswitched 120 VAC 60 Hz electrical outlet with at least 350mA of available current.
Never share the transformer output with any other equipment. The 120 VAC circuit is not power limited.
DC power input to AC input
When powering the XR5FC/SL panel from the 12 VDC output of a FACP, connect the positive wire to the
positive battery terminal of the XR5 and the negative wire to the negative battery terminal of the XR5.
When powering the panel from the DC output of a 24 Volt Fire Alarm Control Panel (FACP), connect the
positive wire from the FACP to terminal 1 and the negative wire to terminal 2.
Do not use battery backup with 12 or 24 VDC input: Do not connect any batteries to the XR5FC or XR5SL
panels when using the 12 or 24 VDC output from a FACP. The XR5FC and XR5SL panels use the backup
battery capability of the FACP for their standby requirements.
Features disabled when using 24 VDC power input: When powering the XR5FC or XR5SL panel from the 24
VDC output of a FACP, the following operational features are disabled:
• Bell Output on the XR5FC
• AC test (XR5FC and XR5SL)
• Battery test (XR5FC and XR5SL)
Always ground the panel before applying power to any devices: The XR5FC and XR5SL panels must be
properly grounded before connecting any devices or applying power to the panels. Proper grounding protects
against Electrostatic Discharge (ESD) that can damage system components. See Earth ground, section 6.2.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 6
Installation
Secondary Power Supply
6.1
Battery terminals 3 and 4
Connect the black battery lead to terminal 4 on the panel and then to the negative terminal of the battery.
The negative terminal connects to the enclosure ground internally through the XR5FC and XR5SL panel
circuit board. Connect the red battery lead to terminal 3 on the panel and then to the positive terminal of the
battery. Observe polarity when connecting the battery.
The XR5FC and XR5SL panels are capable of recharging two 7.0Ah batteries (14 Amp/hours) within 24
hours.
Do not use battery backup with 24 VDC input: Do not connect batteries to the XR5FC and XR5SL panels
when powering the panels with 20 to 28.2 VDC voltage from a Fire Alarm Control Panel (FACP). The
XR5FC and XR5SL panels use the backup battery capability of the FACP for their standby requirements.
Use sealed lead-acid batteries only: Use the DMP Model 367, 12 VDC 7.0Ah sealed lead-acid
rechargeable battery. Batteries supplied by DMP or manufactured by Eagle Picher or Yuasa have been
tested to ensure proper charging with DMP products.
GEL CELL BATTERIES CANNOT BE USED WITH THE XR5FC AND XR5SL.
6.2
Earth ground
Terminal 4 of the XR5FC and XR5SL panels must be connected to earth ground using 14 gauge or larger
wire to provide proper transient suppression. DMP recommends connecting to a metal cold water pipe or
ground rod only. Do not connect to electrical conduit or a telephone company ground.
6.3
Replacement period
DMP recommends the battery be replaced every 3 to 5 years under normal use.
6.4
Discharge/recharge
The battery charging circuit on the XR5FC and XR5SL panels float charge at 13.9 VDC at a maximum
current of 1.2 Amps using the Model 320 Transformer. The total current available is reduced by the
combined auxiliary current draw from terminals 6, 7, 15, 17, 19, and 21. The various battery voltage levels
are listed below:
Battery Trouble:
Battery Restored:
6.5
Below 11.9 VDC
Above 12.6 VDC
Battery supervision
The XR5FC and XR5SL panels test the battery once every hour when AC power is present on terminal 1
and 2. The test lasts for five seconds and consists of the panels putting a load on the battery. If, during the
test, the battery voltage falls below 11.9 VDC a low battery is indicated. The test is then repeated every two
minutes until the battery charges above 12.6 VDC, the battery restored voltage.
If the low battery does not recharge and is replaced with a fully charged battery, the charged battery will not
be detected until the next two minute test is done.
If AC power fails during normal system operation, a low battery is indicated any time the battery voltage
falls below 11.9 VDC.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 7
Installation
6.6
XR5FC and XR5SL power requirements
During AC power failure, the XR5FC and XR5SL panels, and all auxiliary devices connected to the panels, draw
their power from the battery. All devices must be taken into consideration when calculating the battery standby
capacity. Below is a list of the power requirements of the XR5FC and XR5SL panels. Add the additional current
draw of Security Command keypads, smoke detectors, and any other auxiliary devices used in the system for
the total current required.
XR5FC and XR5SL STANDBY BATTERY POWER CALCULATIONS
Standby Current
XR5FC/XR5SL Panels
Relay Outputs 1 and 2 (ON)
Active Zone 1
Active Zones 2 to 5
2-Wire Smokes
Qty _____
Qty _____
Qty _____
Qty _____
x
x
x
x
50mA
30mA
3.3mA
4mA
.1mA
Alarm Current
______ mA
50mA ______ mA
______ mA Qty _____ x 30mA ______ mA
______ mA Qty _____ x 3.3mA ______ mA
______ mA
30mA ______ mA
______ mA Qty _____ x .1mA ______ mA
Bell Output (XR5F only)
1500mA max. ______ mA
670, 770, and 771 Keypads
Annunciator (On)
Qty _____ x
125mA ______ mA Qty _____ x 125mA ______ mA
Qty _____ x 20mA ______ mA
690 & 790 Keypads (annunciator on or off)
Qty _____ x
100mA ______ mA Qty _____ x 100mA ______ mA
692F Keypad
Annunciator (On)
Qty _____ x
30mA ______ mA Qty _____ x
Qty _____ x
Auxiliary Powered Devices on
Terminals 7 and 11
(Other than keypads)
30mA ______ mA
10mA ______ mA
______ mA
______ mA
Total Standby ___________ mA
Total Alarm ____________ mA
* Based on 10% of active zones in alarm condition
Total Standby ____________ mA x number of standby hours needed ______ = ___________ mA/hours
Total Alarm + ___________ mA/hours
Total
___________ mA/hours
x _.001_____
= ___________ A/hours required
Bell Output
7.1
Terminal 5 (XR5FC Only)
Terminal 5 supplies 12 VDC Bell Output to power alarm bells or horns. The output is rated for a maximum of 1.5
Amps. This output can be steady or pulsed depending upon the Bell Action specified in Output Options
programming. Terminal 10 is the ground reference for terminal 5.
4-Wire Smoke Detector Power
8.1
Terminal 6 (XR5FC Only)
Terminal 6 provides up to 100mA at 12 VDC to power 4-wire smoke detectors or other auxiliary powered
devices. This output can be turned off by the user for 5 seconds using the Sensor Reset User Menu option.
Terminal 10 is the ground reference for terminal 6.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 8
Installation
Keypad Data Bus
9.1
Description
Terminals 7, 8, 9, and 10 of the XR5FC and XR5SL panels provide the keypad data bus to which you can
connect Model 692F LED keypads as well as two alphanumeric Security Command keypads.
9.2
Terminal 7 - RED
Terminal 7 provides 12 VDC keypad power for Security Command keypads. You can also connect 12 VDC
auxiliary devices to terminal 7. The ground reference for terminal 7 is terminal 10. The maximum output is rated
at 500mA on the XR5FC and XR5SL panels. All auxiliary devices totalled together must not exceed the panel's
maximum current rating.
9.3
Terminal 8 - YELLOW
Data receive from keypads.
9.4
Terminal 9 - GREEN
Data transmit to keypads.
9.5
Terminal 10 - BLACK
Terminal 10 is the ground reference for keypads and any auxiliary devices being powered by terminal 7.
Class A (Style D) Fire Zone
10.1 Description
Terminals 11 to 14 are the panel's Class A (Style D) fire zone. This zone is suitable for connecting waterflow
devices, heat detectors, and other non-powered fire devices. For programming purposes, this is zone number 1.
The zone is rated for 1.66mA at 5.0 VDC.
The zone configuration on terminals 11 to 14 are described below.
Terminal
11
13
Function
Zone 1 voltage sensing
Zone 1 voltage sensing
Terminal
12
14
Function
Negative for terminal 11
Negative for terminal 13
The voltage sensing terminal measures the voltage flowing through the circuit to the zone's negative terminal.
Dry contact sensing devices can be used only in parallel (normally-open) with zone 1. There are no End of Line
resistors on a Class A (Style D) zone.
Class B (Style A) Fire Zones
11.1 Description
Terminals 15 to 22 are the Class B (Style A) fire zones on the XR5FC and XR5SL panels. These zones are
suitable for connecting powered or non-powered fire devices. For programming purposes, these zones are
designated 2 to 5. The zone configurations on terminals 15 to 22 are described below:
Terminal
15
17
19
21
Function
Zone 2 voltage sensing
Zone 3 voltage sensing
Zone 4 voltage sensing
Zone 5 voltage sensing
Terminal
16
18
20
22
Function
Zone 2 negative
Zone 3 negative
Zone 4 negative
Zone 5 negative
11.2 Operational parameters
The Class B (Style A) zones on the XR5FC and XR5SL panels can detect three conditions: open, normal, and
short. Each zone terminates with a Model 309, 3.3k Ω EOL resistor (provided with the panel) and is rated for
53mA at 12 VDC.
The UL compatibility identifier for use with 2-wire smoke detectors is: A.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 9
Installation
11.3 Zone response time
Make
A condition must be present on the zone for at least
500 milliseconds before it is detected by the XR5FC
and XR5SL panels. Ensure detection devices used on
the zones are rated for use with this delay.
11.4 Compatible 2-wire smoke detectors
The table to the right lists those detectors meeting the
compatibility requirements for use with the Class B
(Stlyle A) zones on the XR5FC and XR5SL fire
panels.
Model
Detector
ID
Detection Systems
DS282
B
None
N/A
10
Detection Systems
DS282TH
B
None
N/A
10
Base
# of
ID
Detectors
Detection Systems
DS250
B
MB2W, MB2WL
A
10
Detection Systems
DS250TH
B
MB2W, MB2WL
A
10
Detection Systems
DS250HD
B
MB2W, MB2WL
A
10
429AT
S09A
None
N/A
12
Hochiki
SLK-835
HD-5
HSB-200, HSB-200N
HB-55
7
Hochiki
SLK-835H
HD-5
HSB-200, HSB-200N
HB-55
7
Hochiki
SLK-12
HD-4
HSB-12-1, HSB-12-1N
HB80
20
Sentrol/ESL
Do not mix detectors from different manufacturers on
the same zone.
Base
Figure 6: Compatible 2-wire smoke detectors
Form C Relay Outputs
12.1 Description
The XR5FC and XR5SL panels can provide two auxiliary Form C (SPDT) relays when equipped with DMP
Model 305 Plug-in Relays in sockets OUTPUT 1 and OUTPUT 2. Each relay is rated for 1 Amp at 30 VDC.
Each output provides one Common, one Normally Open, and one Normally Closed terminal. Field wiring for the
Form C relays connects to the 6-position terminal strip on the lower right corner of the XR5FC and XR5SL
boards.
The Form C relays can be operated by any of the functions listed below:
1) Activation by a zone condition
2) Communication Failure
3) Fire alarm or Fire trouble
Annunciator Outputs
13.1 Description
The XR5FC and XR5SL panels provide four open collector annunciator outputs that can be programmed to
indicate the activity of the panel's zones or conditions occurring on the system. Open collector outputs do not
provide a voltage but instead switch to ground voltage from another source. Each annunciator output is
rated for 50mA at 30 VDC resistive.
Form C and Annunciator outputs operate together: The Form C outputs 1 and 2 are internally connected to
the Annunciator outputs 1 and 2. Any options assigned to Output 1 or 2 in the panel's Output Options
programming applies to both outputs. While the Form C outputs each require a Model 305 Plug-in Relay, the
annunciator outputs will work without the relays.
The Annunciator outputs can respond to any of the conditions listed below:
1) Activation by zone condition
2) Communication failure
3) Fire Alarm or Fire Trouble
13.2 Harness wiring
The Annunciator outputs are accessible by installing the DMP 300 Harness on the 4-pin header labeled J12.
The output locations are shown below:
Output
1
2
3
4
Color
Red
Yellow
Green
Black
Wire
1
2
3
4
Devices connected to the outputs must be located within the same room as the XR5FC and XR5SL panels.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 10
Installation
Telephone RJ Connector
14.1 Description
Connect the panel to the public telephone network by installing DMP 356 RJ Cables between the panel's J4
(MAIN) and J5 (BACKUP) connectors and the RJ31X or RJ38X phone jacks.
14.2 FCC registration
The XR5FC and XR5SL panels comply with FCC part 68 and are registered with the FCC.
Registration number: CCK USA - 18660 - AL - R
Ringer Equivalence: 1.1B
14.3 Notification
Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be
immediately unplugged from the telephone jack. The factory warranty provides for repairs. Registered terminal
equipment may not be used on party lines or in connection with coin telephones. Notification must be given to
the telephone company of:
a. The particular line(s) the service is connected to
b. The FCC registration number
c. The ringer equivalence
d. The make, model, and serial number of the device
Reset Jumpers J9
15.1 Description
There are two reset jumpers located at the top right of the panel's circuit board labeled RESET. Momentarily
shorting these jumpers allows you to reset the microprocessor of the XR5FC and XR5SL panels allowing you to
enter the internal Programmer.
You can reset the panel while the system is operational (for example, during a service call) without powering
down the system.
After resetting the panel for programming, you must begin within 30 minutes. If you wait longer than 30 minutes,
you'll have to reset the panel again.
Silence/Reset button
16.1 Silence/Reset button
The XR5FC and XR5SL panels each contain a mechanical push button located on the top center of the printed
circuit board that allows authorized users to silence alarm bells or sirens and reset latched detection devices.
After pressing the button, the panel silences the Bell output (XR5FC terminal 5) and momentarily drops power to
the auxiliary output (XR5FC terminal 6), the 377 Trouble Annunciator Module, and zones 2 to 5 (both panels).
Additionally, any Fire or Supervisory event displays at the keypads are also cleared. A 2-pin reset header is also
provided for use with keyswitches.
Dual Phone Line Connectors
17.1 Description
The XR5FC and XR5SL panels contain built-in dual phone line capability that allows the panel to monitor two
phone lines, indicate a phone line failure, and switch to the alternate phone line to communicate alarm and
system reports to a central station.
Before sending a report, the panel verifies whether the main phone line is working. If not, the panel sends the
report over the backup phone line. An integrated phone line monitor circuit continually tests the phone lines and
indicates a trouble condition on the line after 90 seconds. If the phone line restores and is good for 90 seconds,
the panel ends the phone line trouble indication.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 11
Installation
UNIVERSAL UL and NFPA FIRE ALARM SPECIFICATIONS
18.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
XR5FC and XR5SL panels in accordance with any of the UL or NFPA fire standards. Additional specifications
may be required by a particular standard.
18.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70.
18.3 Police station phone number
The digital dialer telephone number programmed for communication must not be a police station phone number,
unless that phone number is specifically provided for that purpose.
18.4 System maintenance
Proper installation and regular maintenance by the installing alarm company and frequent testing by the end
user is essential to ensure continuous satisfactory operation of any alarm system. Offering a maintenance
program and acquainting the user with the correct procedure for use and testing of the system is also the
responsibility of the installing alarm company.
18.5 Audible alarm (XR5FC only)
Fire Type zones should be programmed to activate an audible alarm. The Bell Action for Fire Type zones should
not be programmed as “N”. See section 6.3A in the XR5FC and XR5SL Programming Guide (LT-0312).
18.6 UL Listed Receivers
UL has verified operation with the Sur-Gard SG-HLR2-DG, FBII CP220PB, Osborne-Hoffman Quick-Alert, and
Radionics D6500 receivers.
UL 864 NFPA 72 SPECIFICATIONS
Control Units for Fire Protective Signaling Systems
19.1 Power Fail delay
The Power Fail Delay option must be set to 6 hours. See section 5.4 of the Programming Guide (LT-0312).
19.2 Central Station Signaling Systems
Two phone lines must be used. The two phone lines cannot be ground start or party lines. See section 3.3 of the
XR5FC and XR5SL Programming Guide (LT-0312).
Two different phone numbers must be programmed for digital communication. See sections 3.12 and 3.15 of the
XR5FC and XR5SL Programming Guide (LT-0312).
19.3 Local Protective Signaling Systems
The DMP Model 865 or 866 Notification Circuit Module must be used on the bell circuit for detection of shorts
and grounds. See sections 20.1 to 20.3 of this guide.
19.4 Remote Station Protective Signaling Systems
You must provide 60 hours of standby battery. Up to two 12 VDC, 7.0Ah batteries may be used. See section 6.6
for standby battery calculations. Two Radionics Model D127 Reversing Relay Modules may be used to provide
two reversing polarity telephone connections instead of dual phone lines. See section 20.4 and the D127
Installation Instruction sheet for wiring details.
CALIFORNIA STATE FIRE MARSHAL SPECIFICATIONS
20.1 Bell output definition
The bell output of the Model XR5FC must be programmed to operate pulsed on fire alarms. See section 6.3A of
the XR5FC and XR5SL Programming Guide (LT-0312).
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 12
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 13
8
7
6
5
4
3
2
1
3.3k Ω
DMP Model 866
37mA at 12 VDC
S
UL Listed, Polarized
Indicating Devices.
S
S
AUXILIARY
POWER
SUPPLY
1
2
AC
3
B+
4
B–
5
Power Supply
Trouble Contacts
N/C
6
7
S
BELL SMK RED
J5
MAIN BACKUP
Each 866 Notification Circuit Module
in alarm draws up to 35mA from its
terminal 3 alarm input.
AC
J4
NOTE: If an auxiliary supply is not used,
terminals 3 and 4 on the 866 Notification
Circuit Module can be jumpered together
to supply bell power from the XR5F panel.
A maximum of 1.5 Amps at 12 VDC is available
from terminal 5 of the XR5F.
UL Listed, Polarized
Indicating Devices.
10k Ω EOL Resistor
DMP Model 308
S
24 VDC 5 Amp
Maximum
Notification Circuit Module
Bell Trouble
Bell Trouble
Bell Output -
Bell Output +
Bell Power Input
Alarm Input
Ground
Auxiliary Power
Power Supply
Trouble Contacts
N/C
AUXILIARY
POWER
SUPPLY
8
7
6
5
4
3
2
1
10k Ω EOL Resistor
DMP Model 308
9
10
11
12
13
14
S
W
S
ZONE 1
S
S = Supervised Circuit
S
W
S
16
S
S
17
18
19
20
21
Z5+
S S
Z4 –
3.3k Ω
S
Z4+
ZONE 3 ZONE 4
S
Z3 –
3.3k Ω
S
Z3+
PANEL
RESET
22
S
Z5 –
OUTPUT 1
N/C COM N/O N/C COM N/O
OUTPUT 2
J11
1
2
3
4
J12
U21
Auxiliary power supply must be regulated
UL listed for Fire Protection Signaling Service.
Power supplies must have battery backup.
The Auxiliary Power Supply and Indicating
Circuit Module trouble contact zone must
be programmed as a Supervisory Type zone.
ZONE 2
S
Z2 –
3.3k Ω
S
Z2+
15
SILENCE/RESET
PUSH FOR ONE SECOND
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
8
MODEL XR5
EPROM Socket
24 VDC 5 Amp
Maximum
Bell Trouble
Bell Trouble
Bell Output -
Bell Output +
Bell Power Input
Alarm Input
Ground
Auxiliary Power
DMP Model 866
37mA at 12 VDC
Notification Circuit Module
To additional eleven 866 Notification Circuit
Modules. Up to a maximum of thirteen 866
modules on the XR5 panels. Modules must
be installed in a Model 340FC, 340SL, 349, or
350 enclosure connected by no more than 20
feet of conduit.
Installation
21.1 Multiple 866 Notification Circuit Modules
XR5FC/XR5SL Installation Guide
6
Bell A + Output -
Page 14
3.3k Ω
6
7
Bell A + Output -
Bell A – Output
DMP Model 865
85mA at 12 VDC
S
S
S
S
24 VDC 5 Amp
Maximum
Notification Circuit Module
10
11
Bell Trouble
9
Bell Trouble
Bell B – Output
Bell B + Output
5
Bell Power – Input
8
4
3
2
1
Bell Power + Input
Alarm Input
Ground
Auxiliary Power
Power Supply
Trouble Contacts
N/C
AUXILIARY
POWER
SUPPLY
10
11
Bell Trouble
9
8
Bell Trouble
Bell B – Output
Bell B + Output
7
5
Bell Power – Input
Bell A – Output
4
Alarm Input
Bell Power + Input
3
2
1
AUXILIARY
POWER
SUPPLY
Style Y
3
B+
2
AC
1
AC
4
B–
5
6
7
S
BELL SMK RED
NOTE: If an auxiliary supply is not used,
terminals 3 and 4 on the 865 Notification
Circuit Module can be jumpered together
to supply bell power from the XR5F panel.
A maximum of 1.5 Amps at 12 VDC is available
from terminal 5 of the XR5F.
Power Supply
Trouble Contacts
N/C
J5
MAIN BACKUP
8
9
10
11
12
MODEL XR5
13
14
S
W
S
ZONE 1
S
S = Supervised Circuit
S
W
S
16
S
S
17
Z3+
18
19
Z4+
20
21
Z5+
S S
Z4 –
3.3k Ω
S
ZONE 3 ZONE 4
S
Z3 –
3.3k Ω
S
PANEL
RESET
22
Z5 –
S
OUTPUT 1
N/C COM N/O N/C COM N/O
OUTPUT 2
J11
1
2
3
4
J12
U21
Auxiliary power supply must be regulated
UL listed for Fire Protection Signaling Service.
Power supplies must have battery backup.
The Auxiliary Power Supply and Indicating
Circuit Module trouble contact zone must
be programmed as a Supervisory Type zone.
ZONE 2
S
Z2 –
3.3k Ω
S
Z2+
15
SILENCE/RESET
PUSH FOR ONE SECOND
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
Telephone Connections
J4
Each 865 Notification Circuit Module
in alarm draws up to 85mA from its
terminal 3 alarm input.
UL Listed, Polarized
Indicating Devices.
Style Z
UL Listed, Polarized
Indicating Devices.
10k Ω EOL Resistor
DMP Model 308
EPROM Socket
24 VDC 5 Amp
Maximum
XR5FC/XR5SL Installation Guide
Ground
Auxiliary Power
DMP Model 865
85mA at 12 VDC
Notification Circuit Module
To additional three 865 Notification Circuit
Modules. Up to a maximum of five 865
modules on the XR5 panels. Modules must
be installed in a Model 340FC, 340SL, 349, or
350 enclosure connected by no more than 20
feet of conduit.
Installation
21.2 Multiple 865 Notification Circuit Modules
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Installation
21.3 Multiple 866 Notification Circuit Modules for zoned annunciation
To additional ten 866 Notification Circuit
Modules. Up to a maximum of thirteen 866
modules on the XR5FC panel. Modules must
be installed in a Model 340FC, 340SL, 349, or
350 enclosure connected by no more than 20
feet of conduit.
MODEL XR5
MAIN BACKUP
SILENCE/RESET
PUSH FOR ONE SECOND
J5
J4
PANEL
RESET
Telephone Connections
OUTPUT 2
EPROM Socket
OUTPUT 1
U21
J11
1
2
AC
AC
3
B+
4
5
B–
7
6
8
BELL SMK RED
9
10
11
12
13
S S
S
S
Z2+
S
18
17
Z2 –
Z3+
S
S
S
W
S S
16
15
14
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
To additional Zone 1
Notification Circuit Modules.
S
S
Z3 –
S
19
Z4+
20
22
21
Z4 –
S
S
Z5+
Z5 –
J12
S
S
3.3k Ω
N/C COM N/O N/C COM N/O
1
2
3
4
3.3k Ω
Zone 1
Output
ZONE 4 ZONE 5
Zone 2
Output
W
ZONE 1
S
Note: The zone alarm action
programming must be
selected to activate relay
outputs 1 or 2 in order to
activate the appropriate relay.
3.3k Ω
Zone 1 Notification Circuit
Module. DMP Model 866
37mA at 12 VDC
10k Ω EOL Resistor
DMP Model 308
ZONE 2
ZONE 3
1
Auxiliary Power
2
Ground
Output 1 and 2
Common
3
Alarm Input
4
Bell Power Input
5
Bell Output +
S = Supervised Circuit
S
6
Bell Output -
S
Output 1
Normally Open
7
Bell Trouble
8
Output 2
Normally Open
Bell Trouble
Common
Notification Circuit Module
DMP Model 866
37mA at 12 VDC
10k Ω EOL Resistor
DMP Model 308
24 VDC 5 Amp
Maximum
3.3k Ω
AUXILIARY
POWER
SUPPLY
AUXILIARY
POWER
SUPPLY
1
Auxiliary Power
2
Ground
3
Alarm Input
24 VDC 5 Amp
Maximum
4
Bell Power Input
5
Bell Output +
S
6
S
Bell Output -
Power Supply
Trouble Contacts
N/C
7
Bell Trouble
8
Bell Trouble
UL Listed, Polarized
Notification Devices.
Auxiliary power supplies must be
regulated UL listed for Fire Protection
Signaling Service. Power supplies
must have battery backup.
24 VDC 5 Amp
Maximum
AUXILIARY
POWER
SUPPLY
The Auxiliary Power Supply and Notification
Circuit Module trouble contact zone must
be programmed as a Supervisory Type zone.
10k Ω EOL Resistor
DMP Model 308
1
Auxiliary Power
UL Listed, Polarized
Notification Devices.
2
Ground
3
Alarm Input
4
Bell Power Input
5
Bell Output +
NOTE: If an auxiliary supply is
not used, terminals 3 and 4 on the
866 Notification Circuit Module can be
jumpered together to supply bell power
from the XR5F panel.
A maximum of 1.5 Amps at 12 VDC
is available from terminal 5 of the XR5FC.
S
Each 866 Notification Circuit Module
in alarm draws up to 35mA from its
terminal 3 alarm input.
6
Bell Output -
S
7
Bell Trouble
8
Bell Trouble
Zone 2 Notification Circuit
Module. DMP Model 866
37mA at 12 VDC
To additional Zone 2
indicating circuit modules.
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 15
Installation
21.4 Remote Station reversing relay connection
MODEL XR5
MAIN BACKUP
SILENCE/RESET
PUSH FOR ONE SECOND
J5
J4
PANEL
RESET
Telephone Connections
OUTPUT 2
EPROM Socket
OUTPUT 1
U21
J11
1
2
AC
AC
3
B+
4
B–
5
6
7
BELL SMK RED
8
9
10
11
12
13
S
S
S
S
S
Z2+
S
S
17
Z2 –
S
W
S
16
15
14
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
S
S
Z3+
18
19
Z3 –
S
Z4+
20
S S
3.3k Ω
21
Z4 –
Z5+
22
S S
3.3k Ω
N/C COM N/O N/C COM N/O
Z5 –
1
2
3
4
J12
S
3.3k Ω
ZONE 3 ZONE 4 ZONE 5
W
Up to 60 hours of battery standby time
can be supplied using two
7.0Ah sealed lead acid batteries.
ZONE 1
S
S = Supervised Circuit
3.3k Ω
ZONE 2
Reversing Relay Module
Radionics Model D127
12 VDC Supply
5mA Standby
55mA Alarm
Alternate Alarm
Combo Alarm
Fire Alarm Output 1
Auxiliary Power Input
+ Signal Voltage In
Modules must be installed in a Model 340FC,
340SL, 349, or 350 enclosure connected by no
more than 20 feet of conduit.
+ To Remote Receiver
- To Remote Receiver
To Telephone Line
}
- Signal Voltage In
EARTH GROUND
Note: Output 1 must be
programmed as a Fire
Alarm Output and Output
2 must be programmed
as a Fire Trouble Output.
GROUND
GROUND
Intended for connection to a polarity reversal
circuit of a Remote Station receiving unit
having compatible ratings.
This configuration transmits alarm and trouble
signals only and does not transmit
Supervisory signals.
Alternate Alarm
Combo Alarm
For complete system reports, use the 2-line
dialer capability of the panel.
Fire Trouble Output 2
Auxiliary Power Input
+ Signal Voltage In
+ To Remote Receiver
- To Remote Receiver
To Telephone Line
}
- Signal Voltage In
EARTH GROUND
GROUND
GROUND
Reversing Relay Module
Radionics Model D127
12 VDC Supply
5mA Standby
55mA Alarm
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 16
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 17
8
7
6
5
4
3
2
1
3.3k Ω
Notification Circuit Module
DMP Model 866
37mA at 12 VDC
Bell Trouble
Bell Trouble
Bell Output -
Bell Output +
Bell Power Input
Alarm Input
Ground
Auxiliary Power
S
10k Ω EOL Resistor
DMP Model 308
Remote DPDT
Relay
S
Modules must be installed in a
Model 340FC, 340SL, 349, or 350
enclosure connected by no more
than 20 feet of conduit.
Wiring between the 866 module and the
DPDT relay is supervised against opens,
shorts, and grounds. Either of these
trouble conditions cause the 866 module's
Bell Trouble contacts to open.
DMP part #DI-0001 Rectifier
(1N4001 diode) in series with
input from Model 866 terminal 6.
Normally Open
contacts will close
on alarm.
B+
AC
AC
B–
4
6
7
S
BELL SMK RED
5
S = Supervised Circuit
3
2
1
9
10
11
12
13
14
S
S
W
S
S
ZONE 2
3.3k Ω
S
S
S
Z2 –
16
S
S
Z4 –
20
3.3k Ω
Z4+
19
PANEL
RESET
ZONE 3 ZONE 4
S
Z3 –
18
3.3k Ω
S
Z3+
17
S
Z5+
21
S
Z5 –
22
OUTPUT 2
N/C COM N/O N/C COM N/O
OUTPUT 1
The zone connected to the Bell Trouble
contacts on the 866 Notification Circuit
Module must be programmed as a
Supervisory Type zone.
Output 2 Normally Open
Output 1 Common
ZONE 1
S
W
S
Z2+
15
SILENCE/RESET
PUSH FOR ONE SECOND
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
8
MODEL XR5
J11
1
2
3
4
J12
U21
EPROM Socket
Supervised
Silence switch
Normally Closed
contacts will open
on alarm.
DPDT Relay
Use Model ASRB-1 from Advanced Signaling
or Model RBSN-TTL from Altronix.
30mA coil operating current at 12 VDC.
J5
MAIN BACKUP
Telephone Connections
J4
Installation
21.5 Supervised remote relay
XR5FC/XR5SL Installation Guide
XR5FC/XR5SL Installation Guide
2841 E. Industrial Drive Springfield, MO
2841 E. Industrial Drive Springfield,
Page 18MO 65802-6310 800-641-4282
Form C contacts activate on
AC power fail. Use on
XR5SL in DC mode only.
Must delay AC power fail 6
to 12 hours.
Form C or A contacts
activate on Supervisory
condition.
Form C trouble contacts
activate on General Trouble.
General Trouble must not
be used to indicate AC
power fail unless it can be
delayed 6 to 12 hours.
Form C alarm contacts
activate on General
Alarm.
{
{
{
{
Normally Closed
Common
Normally Open
Normally Closed
Common
Normally Open
Normally Closed
Common
Normally Open
Normally Closed
Common
Normally Open
Negative 12/24 VDC Auxiliary Ouput
Positive 12/24 VDC Auxiliary Ouput
8
7
6
5
4
3
2
1
3.3k Ω
3.3k Ω
3.3k Ω
3.3k Ω
Optional DC Mode
AC Mode
DMP Model 320
Transformer
J5
MAIN BACKUP
3
B+
2
AC
S
1
AC
S
B–
4
6
7
BELL SMK RED
5
8
9
10
11
12
MODEL XR5
13
S
ZONE 1
S
ZONE 5
ZONE 4
ZONE 3
ZONE 2
S = Supervised Circuit
S
14
S
15
Z2+
S
16
S
Z2 –
S
Z3+
17
S
Z3 –
18
3.3k Ω
SILENCE/RESET
PUSH FOR ONE SECOND
YEL GRN BLK Z1A+ Z1A– Z1B+ Z1B–
Telephone Connections
J4
DC Mode Wiring
When the XR5SL is used in the DC mode, the FACP
must indicate AC power fail on an independant relay
output. This output must delay the AC power fail 6
to 12 hours. Use EST Model IRC-3 or Federal Signal
3000, 5000, or 5000E.
S
Z4+
19
S
Z4 –
20
3.3k Ω
PANEL
RESET
21
Z5+
S
22
S
Z5 –
OUTPUT 2
OUTPUT 1
N/C COM N/O N/C COM N/O
J11
1
2
3
4
J12
U21
EPROM Socket
Main Fire Alarm
Control Panel (FACP)
120 VAC
60Hz
350mA
AC Mode Wiring
When the XR5SL is used in the AC mode, the DMP
Model 320 Transformer must be connected to the
same branch circuit as the FACP. An AC power fail
can then be delayed 6 to 12 hours by the XR5SL
programming. See section 5.4 of the XR5SL
Programming Guide (LT-0312).
The FACP must not indicate AC fail to the XR5SL.
Use Fire-Lite Models MS9200 or MS5012.
Installation
21.6 XR5SL Connection to FACP
Digital Monitoring Products
65802-6310 800-641-4282
Download PDF