Dacor | REMP3 | Specifications | Dacor REMP3 Specifications

Installation Instructions
Remote Blowers
READ AND SAVE THESE INSTRUCTIONS
TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI/UL507, STANDARD FOR ELECTRIC FANS, AND
CSA C22.2 NO. 113, STANDARD FOR FANS AND VENTILATORS.
CONVENTIONS USED IN THESE INSTRUCTIONS
WARNINGS:
Must be followed carefully to avoid personal injury or damage.
NOTES:
Contain helpful hints and tips to facilitate the installation.
IMPORTANT
1.
2.
3.
4.
5.
Before beginning installation, please thoroughly read and become familiar with these instructions.
Installation and service must be completed by a qualified installer or service agency.
Installer: Please leave these Installation Instructions with the owner.
Owner: Please keep these instructions for local electrical inspector’s use and for future reference.
Read the accompanying Use & Care Manual prior to operating this appliance.
TABLE OF STEPS
Installation Planning
Electrical Connection
Installing the ILB
Installing the REMP
Verifying Proper Operation
Part No. 65265 Rev. D
Pages 2-3
Pages 3-5
Page 6
Page 6
Page 6
WARNING:
IMPORTANT SAFETY INSTRUCTIONS
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE
FOLLOWING:
a) Installation work and
electrical wiring must be
done by qualified person(s)
in accordance with all
applicable codes and
standards, including fire-rated
construction.
b) Sufficient air is needed
for proper combustion
and exhausting of gases
through the flue (chimney)
of fuel burning equipment
to prevent back drafting.
Follow the heating equipment
manufacturer’s guidelines
and safety standards such
as those published by the
National Fire Protection
Association (NFPA), and
the American Society for
Heating, Refrigeration and
Air Conditioning Engineers
(ASHRAE), and the local code
authorities.
c) When cutting or drilling into
wall or ceiling, do not damage
electrical wiring and other
hidden utilities.
d) Ducted fans must always be
vented outdoors.
e) Use this unit only in the
manner intended by the
manufacturer. If you have
questions, contact the
manufacturer.
f) Before servicing or cleaning
unit, switch power off at
service panel and lock
the service disconnecting
means to prevent power
from being switched on
accidentally. When the service
disconnecting means cannot
be locked, securely fasten a
prominent warning device,
such as a tag, to the service
panel.
g) Blower must not be installed
in a ceiling thermally insulated
to a value greater than R40.
h) Blower must not be installed
in furnace ductwork.
1
WARNING:
TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCTWORK.
WARNING:
TO REDUCE THE RISK OF A
RANGE TOP GREASE FIRE:
a) Never leave surface units
unattended at high settings.
Boilovers cause smoking and
greasy spillovers that may
ignite. Heat oils slowly on low
or medium settings.
b) Always turn hood ON when
cooking at high heat or when
flambeing food (i.e. Crepes
Suzette, Cherries Jubilee,
Peppercorn Beef Flambe’).
c) Clean ventilating fans
frequently. Grease should not
be allowed to accumulate on
fan or filter.
d) Use proper pan size. Always
use cookware appropriate
for the size of the surface
element.
CAUTION:
For General Ventilating Use Only.
Do Not Use To Exhaust Hazardous
Or Explosive Materials And
Vapors.
CAUTION:
To reduce risk of fire and to
properly exhaust air, be sure to
duct air outside – Do not vent
exhaust air into spaces within
walls or ceilings or into attics,
crawl spaces or garages.
NOTES:
1.
2.
3.
WARNING:
TO REDUCE THE RISK OF INJURY
TO PERSONS IN THE EVENT OF
A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
a) SMOTHER FLAMES with a
close-fitting lid, cookie sheet,
or metal tray, then turn off
the burner. BE CAREFUL
TO PREVENT BURNS. If
the flames do not go out
immediately, EVACUATE
AND CALL THE FIRE
DEPARTMENT.
b) NEVER PICK UP A FLAMING
PAN - You may be burned.
c) DO NOT USE WATER,
including wet dishcloths
or towels - a violent steam
explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a Class
ABC extinguisher, and
you already know how to
operate it.
2) The fire is small and
contained in the area where
it started.
3) The fire department is being
called.
4) You can fight the fire with
your back to an exit.
4.
5.
6.
Consult a licensed ventilation
contractor or qualified
technician for proper
installation of exhaust
ducting.
Locate the cooking area for
minimum cross drafts – away
from doors and windows,
when possible.
Ducts must be of adequate
size and duct runs should
be as short and straight as
possible. Where turns are
necessary, keep turning
radius as large and smooth as
possible.
The ducting must be air tight.
Use a minimum of 2 sheet
metal screws at every duct
joint. Then, seal the duct joints
with a high quality duct tape.
In duct runs less than 10
equivalent straight feet, the
remote blower may interfere
with the cooktop burner
performance due to the
high volume of air moved.
An adjustable damper (not
included) should be installed
in the ducting system. The
damper can be adjusted so
that proper ventilation and
cooktop burner performance
is achieved.
Installation of duct work
should be carefully planned
if it is to go under a concrete
slab floor. The duct trench
should be boxed to prevent
collapse from the wet cement.
Be sure to allow room to
run the electrical wiring and
conduit.
Installation Planning
Model
No.
A qualified technician must complete the
installation of this appliance.
Carefully check the location where the remote
blower is to be installed. The remote blower
should be placed for convenient access. Make
certain that electrical power can be provided in
the selected location.
Plan the installation so that all minimum
clearances are met or exceeded. Dimensions
shown provide minimum clearances, unless
otherwise noted.
ILB8
10 5/8” (270mm)
10 1/2” (267mm)
ILB10
12 5/8” (321mm)
12 1/2” (318mm)
Overall Chassis
Length “C”
Duct Diameter
“D”
8” (203mm)
5” (127mm)
10” (254mm)
ILB Overall Dimensions
Model
No.
ILB10
Electrical Supply
Requirements
Maximum
Duct Length
Refer to Ventilator
Specifications
Max. 60
Equivalent
Straight Feet
Total
Connected
Load
Blower
Rating*
Approximate
Shipping Weight
0.1kW (1A)
500 CFM
15 lbs.
0.2kW (2A)
900 CFM
18 lbs.
ILB Specifications
All dimensional tolerances are
+ 1/16”, - 0” unless otherwise
stated.
Before commencing
installation, remove the top
cover of the remote blower
(REMP ONLY). Check to see
if the blower wheel turns
freely. Do not replace the top
cover until the installation is
complete.
Model
No.
Overall Chassis
Width
Overall Chassis
Height
Overall Chassis
Length
Duct Diameter
REMP3
19” (483mm)
5 13/16” (148mm)
25 1/2” (648mm)
8” (203mm)
REMP16
26” (660mm)
9 9/16” (243mm)
33 1/2” (851mm)
10” (254mm)
REMP Overall Dimensions
Model
No.
REMP3
REMP16
Electrical
Supply
Requirements
Maximum
Duct Length
Refer to
Ventilator
Specifications
Max. 60
Equivalent
Straight Feet
Total
Connected
Load
Blower
Rating*
Approx.
Shipping
Weight
0.5kW (4A)
620 CFM
35 lbs.
0.3kW (3A)
980 CFM
55 lbs.
Finish
Galvanized
(may be
painted)
REMP Specifications
"A"
* All the CFM Blower Ratings are valued at 0” (zero-inch) static pressure.
19" (483mm)
17 1/8" (435mm)
9 1/2" (241mm)
7 1/2"
(191mm)
CL
"B"
CL
Power Supply
Conduit
Location
25 1/2"
(648mm)
Attachment
Surface
Electrical
Access Panel
L
BK
M
WIRING DIAGRAM, ILB-8
FAN MOTOR
N
GR
120V, 60Hz, 15A POWER SUPPLY
CAUTION: DISCONNECT POWER SUPPLY AT THE FUSE BOX BEFORE SERVICING THIS EQUIPMENT
Intake Collar
Cutout
Location
Discharge
ILB Overall Dimensions
Front View
26" (660mm)
24" (610mm)
12 11/16" (322mm)
9 1/2"
(241mm)
3 5/8"
(92mm)
CL
CL
Power Supply
Conduit
Location
9 1/4"
(235mm)
CL
24 1/16"
(611mm)
DACOR P/N 85829
2.
Overall Chassis
Height “B”
ILB8
NOTES:
1.
Overall Chassis
Width “A”
33 1/2"
(851mm)
12 1/4"
(311mm)
CL
31 1/2"
(800mm)
Mounting
Flange
3 1/2"
(89mm)
Intake Collar
Cutout
Location
Mounting
Flange
Discharge
REMP3 Overall Dimensions
Top View
7 13/16"
(198mm)
5 13/16"
(148mm)
REMP16 Overall Dimensions
Top View
11 1/2"
(292mm)
9 9/16"
(243mm)
"D"
AIRFLOW
8"
(203mm)
10"
(254mm)
Intake Collar
Intake Collar
ROTATION
Attachment
Surface
"C"
Discharge
Discharge
ILB Overall Dimensions
Side View
REMP3 Overall Dimensions
Side View
REMP16 Overall Dimensions
Side View
2
NOTE:
The ILB8 & ILB10 inline blowers
are only approved in updraft
(hood) applications.
REMP
Air
Discharge
NOTE:
The REMP must be sealed
between the roof or wall and
the underside of the flange with
mastic to prevent leaks. For
installation on a flat roof, or a
roof with a pitch of less than 2:12,
install the REMP on a curb as
shown below. Position the curb
on flat roofs so that the discharge
(low) end points away from the
prevailing wind.
45° Adjustable
Elbow
3 1/4" x 10" to
Round
Transistion
Dacor Preference
and Millennia Cooktops
RV
AIR
Roof Curb
3 1/4" x 10"
90° Elbow
3 1/4" x 10"
90° Elbow
REMP Roof Installation
Side View
Electrical Connection
REMP Flat Roof Installation
Flange
WARNINGS:
Sealant
REMP
Air
Discharge
1.
2.
Sealant
45° Adjustable
Elbow
Round Duct
3.
REMP Sloped Roof Installation
2"
(51mm)
4.
25 1/2"
(648mm)
6"
(152mm)
5.
2"
(51mm)
19"
(483mm)
23 1/4"
(591mm)
REMP3 Sloped Roof Installation
2"
(51mm)
33 1/2"
(851mm)
6"
(152mm)
6.
2"
(51mm)
26"
(660mm)
30 1/2"
(776mm)
REMP16 Roof Curb Dimensions
3
Ensure that the power supply
is disconnected before
proceeding.
Verify that the power supply
matches the ratings found on
the appliance data plate before
proceeding.
The complete appliance must
be properly grounded at all
times when electrical power is
applied.
Do not ground the appliance
with the neutral (white) house
supply wire. A separate
ground wire must be utilized.
If aluminum house supply
wiring is used, splice the
appliance copper wires to the
aluminum house wiring with
special connectors designed
and agency-certified for this
purpose. Follow the connector
manufacturer’s recommended
procedure carefully. Improper
connection can result in a fire
hazard.
Failure to complete electrical
connections properly may
result in a damaged or nonfunctional system. Follow the
wiring diagrams carefully to
ensure a proper installation.
It is the owner’s responsibility to ensure that
a qualified electrician performs the electrical
connection of this appliance. The electrical
installation, including minimum supply wire
size, must comply with the latest revision of the
National Electric Code ANSI/NFPA 70* and local
codes and ordinances.
*A copy of this standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
NOTES:
1.
2.
Make all electrical connections
between the vent and blowers,
then connect power to the
vent as per the wiring diagram
shown.
Use wire nuts and electrical
tape to secure all wiring
connections at the blowers.
REMP
BLK
L2
N2
WHT
Gnd
GRN
RV
Gnd
GRN
GRN
Gnd
GRN
WHT
N1
WHT
BLK
L1
BLK
N2
WHT
L2
BLK
120VAC, 60Hz, 15A
Supply power from
dedicated circuit breaker
J-BOX
CABP3
BLK
L2
N2
WHT
Gnd
GRN
Wiring of RV with REMP and CABP3
RV
Gnd
GRN
GRN
Gnd
GRN
WHT
N1
WHT
BLK
L1
BLK
N2
WHT
L2
BLK
120VAC, 60Hz, 15A
Supply power from
dedicated circuit breaker
REMP OR CABP3
L2
BLK
N2
WHT
Gnd
GRN
Wiring of RV with REMP or CABP3
ERV/PRV
Gnd
GRN
GRN
Gnd
GRN
WHT
N1
WHT
BLK
L1
BLK
N2
WHT
L2
BLK
120VAC, 60Hz, 15A
Supply power from
dedicated circuit breaker
REMP
L2
BLK
N2
WHT
Gnd
GRN
Wiring of ERV/PRV with REMP
4
ILB
BLK
L2
BLK
WHT
N2
WHT
GRN
Gnd
GRN
HOOD
L1
BLK
N1
WHT
Gnd
GRN
L2
BLK
N2
WHT
Gnd
GRN
120VAC, 60Hz, 15A
Supply power from
dedicated circuit breaker
HOOD
Wiring of DACOR Hood with ILB
L1
BLK
N1
WHT
Gnd
GRN
L2
BLK
N2
WHT
Gnd
GRN
120VAC, 60Hz, 15A
Supply power from
dedicated circuit breaker
REMP
L2
BLK
L2
BLK
WHT
N2
WHT
GRN
Gnd
GRN
REMOTE BLOWER/
HOOD
L1
BLK
N1
WHT
Gnd
GRN
120VAC, 60Hz, 15A
Supply power from
dedicated circuit breaker
J-BOX
L2
BLK
N2
WHT
Gnd
GRN
REMP
L2
BLK
N2
WHT
Gnd
GRN
Wiring of DACOR Remote Blower/Hood with ILB and REMP
5
WHT
Gnd
GRN
Wiring of DACOR Hood with REMP
ILB
BLK
N2
Installing the ILB
Mount the ILB using the 4 screws, isolation
grommets and washers provided in the Parts
Bag, included in the Instruction Envelope.
Installing the REMP
Mount the REMP to the wall or roof using
screws, through mounting trim flange.
Verifying Proper Operation
1.
2.
3.
Temporarily re-install the remote blower
cover, using 2 screws per side (REMP
ONLY).
Turn on the power supply at the circuit
breaker.
Refer to Ventilator Installs for further
instructions on verifying the proper
operation.
NOTES:
If the remote blower does not
operate properly, follow these
troubleshooting steps:
1. Verify that power is being
supplied to the Ventilator and
the remote blower.
2. Check the electrical
connections to ensure that
the installation has been
completed correctly.
3. Repeat the above test.
4. If the appliance still does not
work, contact an authorized
DACOR service company.
If you are unable to locate
a DACOR Servicer, please
contact DACOR at (800)
793-0093, or visit us on the
web at www.dacor.com. Do
not attempt to repair the
appliance yourself. DACOR
is not responsible for service
required to correct a faulty
installation.
6
Web Site:
www.dacor.com
For a Dealer/Service: (800) 772-7778
Corporate Phone:
(800) 793-0093
Download PDF