Capresso | F7 | IMPRESSA F7 - Welcome to the world of JURA coffee machines


IMPRESSA F7 – Quick Reference Guide
The ‘IMPRESSA F7 Instructions for Use’ together with these short instructions ‘IMPRESSA F7 – Quick Reference Guide’ has been awarded the seal
of approval by the independent German Technical Inspection Agency,
TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.
IMPRESSA F7 – Quick Reference Guide
IMPRESSA F7 – Quick Reference Guide
J
These short instructions do not replace the ‘IMPRESSA F7 Instructions for Use’. Make sure you read and observe the safety information and warnings first in order to avoid hazards.
Rinsing the machine
You can initiate the rinse operation manually at any time.
Precondition: READY is displayed.
T Place a receptacle under the coffee spout.
k T Press and hold the Rotary Switch until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
C CLEANING
g T Turn the Rotary Switch until RINSE is displayed.
k T Press the Rotary Switch to initiate the rinse operation.
RINSING, water flows out of the coffee spout.
The rinse stops automatically. READY appears on the display.
Rinsing the fine foam
frother
EE This chapter applies to the professional fine foam frother
and the fine foam frother.
After each milk preparation, the IMPRESSA prompts you to perform
a cappuccino rinse.
Precondition: RINSE CAPPUCCINO is displayed and the Maintenance button c lights up.
T Place a receptacle under the fine foam frother.
c T Press the Maintenance button.
SWITCH OPEN
The arrow on the switch lights up.
j T Turn the switch to the m position.
CAPPUCCINO RINSING, the fine foam frother is
rinsed.
The rinse stops automatically. SWITCH CLOSE appears
on the display.
h T Turn the switch to the ° position.
The illuminated arrow on the switch goes out. READY
appears on the display.
2
IMPRESSA F7 – Quick Reference Guide
Cleaning the fine foam
frother
EE This chapter applies to the professional fine foam frother
and the fine foam frother.
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk. Your
IMPRESSA will not prompt you to clean the fine foam frother.
CAUTION
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
EE JURA Cappuccino Cleaner is available from specialised dealers.
Precondition: READY is displayed.
k T Press and hold the Rotary Switch until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
C CLEANING
k T Press the Rotary Switch.
CLEANER FOR CAPPU.
T Remove the milk pipe from the milk container or carton.
T Pour 250 ml of fresh water into a receptacle and add one
capful of Cappuccino Cleaner.
T Immerse the milk pipe in the receptacle.
T Place a receptacle under the fine foam frother.
k T Press the Rotary Switch.
HEATING / STEAM
As soon as the machine has heated up, SWITCH OPEN
appears.
The arrow on the switch lights up.
j T Turn the switch to the m position.
CAPPUCCINO CLEANING, the fine foam frother and
the milk pipe are cleaned.
SWITCH CLOSE
h T Turn the switch to the ° position.
WATER FOR CAPPUCCINO
T Rinse the receptacle thoroughly, fill it with 250 ml of fresh
water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the fine foam
frother once more.
3
IMPRESSA F7 – Quick Reference Guide
j T Turn the switch to the m position.
CAPPUCCINO CLEANING, the fine foam frother and
the milk pipe are rinsed with fresh water.
SWITCH CLOSE
h T Turn the switch to the ° position.
The illuminated arrow on the switch goes out. READY
appears on the display.
Dismantling and rinsing
the fine foam frother
To make sure the fine foam frother works properly, and in the interests of hygiene, it must be dismantled and rinsed daily if you have
been preparing milk. Your IMPRESSA will not prompt you to dismantle and rinse the frother.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Carefully remove the fine foam frother from the Connector
System© by twisting slightly.
T Dismantle the fine foam frother into its individual parts.
T Rinse all the parts of the fine foam frother thoroughly under
running water. If there are severely dried-on milk residues,
firstly immerse the individual parts in JURA Cappuccino
Cleaner and then rinse them thoroughly.
T Re-assemble the fine foam frother.
EE Ensure that all individual parts are correctly and firmly connected to ensure optimum operation.
T Firmly attach the fine foam frother to the Connector
System©.
Dismantling and rinsing
the professional fine
foam frother
4
To make sure the professional fine foam frother works properly, and
in the interests of hygiene, it must be dismantled and rinsed daily if
you have been preparing milk. Your IMPRESSA will not prompt you
to dismantle and rinse the frother.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Carefully remove the professional fine foam frother from the
Connector System© by twisting slightly.
IMPRESSA F7 – Quick Reference Guide
T Dismantle the professional fine foam frother into its individual parts.
T Rinse all the parts of the professional fine foam frother thoroughly under running water. If there are severely dried-on
milk residues, firstly immerse the individual parts in JURA
Cappuccino Cleaner and then rinse them thoroughly.
T Re-assemble the professional fine foam frother.
EE Ensure that all individual parts are correctly and firmly connected to ensure optimum operation.
T Firmly attach the professional fine foam frother to the Connector System©.
Inserting and activating
the filter
Your IMPRESSA no longer has to be descaled if you are using the
CLARIS Blue filter cartridge. If you did not activate the filter cartridge
the first time you used the machine, you can do this now as follows.
EE Perform the ‘inserting the filter’ operation without any interruptions. This will ensure that your IMPRESSA always produces
its best.
Precondition: READY is displayed.
k T Press and hold the Rotary Switch until RINSE appears.
g T Turn the Rotary Switch until FILTER - is displayed.
k T Press the Rotary Switch to enter the programme item.
NO
g T Turn the Rotary Switch until YES is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
FILTER INSERT
T Remove and empty the water tank.
T Open the filter holder.
T Remove the CLARIS Blue filter cartridge from the Welcome
Pack.
5
IMPRESSA F7 – Quick Reference Guide
T Insert the CLARIS Blue filter cartridge into the water tank,
exerting slight pressure.
T Close the filter holder. It will click into place audibly.
EE After two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place a receptacle (at least 300 ml) under the fine foam
frother.
k T Press the Rotary Switch.
SWITCH OPEN
The arrow on the switch lights up.
j T Turn the switch to the m position.
FILTER RINSING, water flows out of the fine foam
frother.
EE You can interrupt rinsing of the filter at any time. To do this,
turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
EE The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
300 ml. SWITCH CLOSE appears on the display.
h T Turn the switch to the ° position.
The illuminated arrow on the switch goes out.
HEATING, the machine heats up.
READY appears on the display. The filter is now activated.
Changing the filter
6
EE After 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you
to change the filter.
EE After two months, the filter will cease to work. Set the date on
the date plate on the filter holder in the water tank.
EE If the CLARIS Blue filter cartridge is not activated in programming mode, you will not be prompted to change the filter.
EE CLARIS filter cartridges are available from specialised dealers.
IMPRESSA F7 – Quick Reference Guide
Precondition: READY / FILTER is displayed and the Maintenance button c lights up.
c T Press the Maintenance button.
FILTER CHANGE
T Remove and empty the water tank.
T Open the filter holder and remove the old CLARIS Blue filter
cartridge.
T Insert a new CLARIS Blue filter cartridge into the water tank,
exerting slight pressure.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place a receptacle (at least 300 ml) under the fine foam
frother.
k T Press the Rotary Switch.
SWITCH OPEN
The arrow on the switch lights up.
j T Turn the switch to the m position.
FILTER RINSING, water flows out of the fine foam
frother.
EE You can interrupt rinsing of the filter at any time. To do this,
turn the switch clockwise. Turn the switch anticlockwise to
continue rinsing the filter.
EE The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
300 ml. SWITCH CLOSE appears on the display.
h T Turn the switch to the ° position.
The illuminated arrow on the switch goes out.
HEATING, the machine heats up.
READY appears on the display.
7
IMPRESSA F7 – Quick Reference Guide
Cleaning the machine
CAUTION
After 200 preparations or 80 switch-on rinses, the IMPRESSA will
prompt you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
EE The cleaning programme lasts approximately 20 minutes.
EE Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
EE JURA cleaning tablets are available from specialised dealers.
Precondition: READY / CLEAN is displayed and the Maintenance
button c lights up.
c T Press the Maintenance button.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE, the Maintenance button c lights up.
T Place a receptacle under the coffee spout.
c T Press the Maintenance button.
CLEANING, water flows out of the coffee spout.
The operation is interrupted, ADD TABLET.
T Open the cover of the filler funnel for ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
PRESS RINSE, the Maintenance button c lights up.
c T Press the Maintenance button.
CLEANING, water flows out of the coffee spout several
times.
The operation stops automatically.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
HEATING
READY appears on the display. Cleaning is now complete.
Your IMPRESSA is once more ready for use.
8
IMPRESSA F7 – Quick Reference Guide
Descaling the machine
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the hardness of your water.
J CAUTION
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
CAUTION
If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
CAUTION
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling programme to run to the end.
CAUTION
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
EE The descaling programme lasts approximately 45 minutes.
EE JURA descaling tablets are available from specialised dealers.
EE If you use a CLARIS Blue filter cartridge and this is activated,
you will not be prompted to descale.
Precondition: READY / DESCALE is displayed and the Maintenance button c lights up.
c T Press the Maintenance button.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
AGENT IN TANK
T Remove and empty the water tank.
9
IMPRESSA F7 – Quick Reference Guide
T Completely dissolve the contents of one blister (3 JURA descaling tablets) in a receptacle holding 500 ml of water. This
may take several minutes.
T Pour the solution into the empty water tank and insert it into
the machine.
SWITCH OPEN
The arrow on the switch lights up.
T Carefully remove the fine foam frother from the Connector
System© by twisting slightly.
T Place a receptacle (at least 500 ml) under the Connector
System©.
j T Turn the switch to the m position.
DESCALING, water flows out of the Connector System©
several times. The Maintenance button c flashes during the
descaling operation.
The operation is interrupted, SWITCH CLOSE.
h T Turn the switch to the ° position.
DESCALING, the descaling operation is continued. The
Maintenance button c flashes during the descaling operation.
The operation is interrupted, EMPTY TRAY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
FILL WATER TANK
T Empty the receptacle and place it under the Connector
System© and the coffee spout.
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
SWITCH OPEN
The arrow on the switch lights up.
j T Turn the switch to the m position.
DESCALING, the descaling operation is continued. The
Maintenance button c flashes during the descaling operation.
The operation is interrupted, SWITCH CLOSE.
10
F7_Kurz/en/201211
IMPRESSA F7 – Quick Reference Guide
h T Turn the switch to the ° position.
DESCALING, the descaling operation is continued. The
Maintenance button c flashes during the descaling operation.
The operation is interrupted, DESCALING.
Water flows out of the coffee spout.
EMPTY TRAY
T Re-assemble the fine foam frother.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
READY appears on the display. Descaling is now complete.
Your IMPRESSA is once more ready for use.
EE If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
11
Download PDF