Watlow Electric | EZ-ZONE PM | User`s guide | Watlow Electric EZ-ZONE PM User`s guide

EZ-ZONE PM
®
User’s Guide
PID Controller Models
TOTAL
CUSTOMER
SATISFACTION
3 Year Warranty
ISO 9001
Registered Company
Winona, Minnesota USA
1241 Bundy Boulevard., Winona, Minnesota USA 55987
Phone: +1 (507) 454-5300, Fax: +1 (507) 452-4507 http://www.watlow.com
0600-0058-0000 Rev. N
January 2015
Made in the U.S.A.
Safety Information
Unit is a Listed device per Underwriters Laboratories®. It has
been evaluated to United States
and Canadian requirements for
Hazardous Locations Class 1
Division II Groups A, B, C and D.
ANSI/ISA 12.12.01-2007. File
E184390 QUZW, QUZW7. See:
www.ul.com
We use note, caution and warning symbols throughout this book to draw your attention to important
operational and safety information.
A “NOTE” marks a short message to alert you to
an important detail.
A “CAUTION” safety alert appears with information that is important for protecting your equipment and performance. Be especially careful to
read and follow all cautions that apply to your
application.
Unit is compliant with European
Union directives. See Declaration of Conformity for further
details on Directives and Standards used for Compliance.
A “WARNING” safety alert appears with information that is important for protecting you, others and equipment from damage. Pay very close
attention to all warnings that apply to your
application.
The electrical hazard symbol, Ó (a lightning bolt
in a triangle) precedes an electric shock hazard
CAUTION or WARNING safety statement.
Symbol
Unit has been reviewed and
approved by Factory Mutual as
a Temperature Limit Device per
FM Class 3545 standard. See:
www.fmglobal.com
Unit has been reviewed and
approved by CSA International
for use as Temperature Indicating-Regulating Equipment per
CSA C22.2 No. 24. See: www.
csa-international.org
Explanation
Unit has been reviewed and approved by ODVA for compliance
with DeviceNet communications
protocol. See: www.odva.org
CAUTION – Warning or Hazard
that needs further explanation
than label on unit can provide.
Consult User's Guide for further
information.
ESD Sensitive product, use
proper grounding and handling
techniques when installing or
servicing product.
Unit protected by double/reinforced insulation for shock
hazard prevention.
Do not throw in trash, use
proper recycling techniques or
consult manufacturer for proper
disposal.
Enclosure made of Polycarbonate
material. Use proper recycling
techniques or consult manufacturer for proper disposal.
Unit can be powered with either
alternating current (ac) voltage
or direct current (dc) voltage.
Unit is a Listed device per Underwriters Laboratories®. It has
been evaluated to United States
and Canadian requirements for
Process Control Equipment. UL
61010 and CSA C22.2 No. 61010.
File E185611 QUYX, QUYX7.
See: www.ul.com
Unit has been reviewed and approved by ODVA for compliance
with Ethernet/IP communications protocol. See: www.odva.
org
Warranty
The EZ-ZONE® PM is manufactured by ISO
9001-registered processes and is backed by a threeyear warranty to the first purchaser for use, providing that the units have not been misapplied. Since
Watlow has no control over their use, and sometimes
misuse, we cannot guarantee against failure. Watlow’s obligations hereunder, at Watlow’s option, are
limited to replacement, repair or refund of purchase
price, and parts which upon examination prove to be
defective within the warranty period specified. This
warranty does not apply to damage resulting from
transportation, alteration, misuse or abuse. The purchaser must use Watlow parts to maintain all listed
ratings.
Technical Assistance
If you encounter a problem with your Watlow controller, review your configuration information to verify
that your selections are consistent with your application: inputs, outputs, alarms, limits, etc. If the problem persists, you can get technical assistance from
your local Watlow representative (see back cover), by
e-mailing your questions to wintechsupport@watlow.
com or by dialing +1 (507) 494-5656 between 7 a.m.
and 5 p.m., Central Standard Time (CST). Ask for for
an Applications Engineer. Please have the following
information available when calling:
• Complete model number
• All configuration information
• User's Guide
• Factory Page
Return Material Authorization (RMA)
1. Call Watlow Customer Service, (507) 454-5300, for
a Return Material Authorization (RMA) number
before returning any item for repair. If you do not
know why the product failed, contact an Application
Engineer or Product Manager. All RMA’s require:
• Ship-to address
• Bill-to address
• Contact name
• Phone number
• Method of return shipment
• Your P.O. number
• Detailed description of the problem
• Any special instructions
• Name and phone number of person returning the
product.
2. Prior approval and an RMA number from the
Customer Service Department is required when
returning any product for credit, repair or evaluation. Make sure the RMA number is on the outside of
the carton and on all paperwork returned. Ship on a
Freight Prepaid basis.
3. After we receive your return, we will examine it and
try to verify the reason for returning it.
4. In cases of manufacturing defect, we will enter a
repair order, replacement order or issue credit for
material returned. In cases of customer misuse, we
will provide repair costs and request a purchase
order to proceed with the repair work.
5. To return products that are not defective, goods
must be in new condition, in the original boxes and
they must be returned within 120 days of receipt.
A 20 percent restocking charge is applied for all
returned stock controls and accessories.
6. If the unit is not repairable, you will receive a letter
of explanation. and be given the option to have the
unit returned to you at your expense or to have us
scrap the unit.
7. Watlow reserves the right to charge for no trouble
found (NTF) returns.
The EZ-ZONE® PM PID Controller User's Guide is copyrighted by Watlow Electric, Inc., © January 2015 with all
rights reserved.
EZ-ZONE® PM is covered by U.S. Patent No. 6,005,577
and Patents Pending
TC
Table of Contents
Chapter 1: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Standard Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Getting Started Quickly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2: Install and Wire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 3: Keys and Displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapter 4: Home Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Conventions Used in the Menu Pages . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 5: Operations Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Analog Input Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Linearization Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Process Value Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Digital Input/Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Monitor Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Control Loop Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Alarm Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Timer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Profile Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Chapter 6: Setup Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Analog Input Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Linearization Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Process Value Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Digital Input/Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Control Loop Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Output Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Alarm Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Timer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Function Key Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Global Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Communications Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Real Time Clock Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Watlow EZ-ZONE ® PM PID Controller
•
1 •
Table of Contents
TC
Table of Contents (cont.)
Chapter 7: Profiling Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Profile Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Starting a Profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Profiling Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Chapter 8: Factory Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Custom Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Security Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Security Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Diagnostics Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Chapter 9: Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Changing PM PID Model Number to PM User Mode. . . . . . . . . . . . . . . 88
Saving and Restoring User Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Programming the Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Tuning the PID Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Control Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Timer Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Open Loop Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Programming the EZ Key/s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Using Lockout and Password Security. . . . . . . . . . . . . . . . . . . . . . . . . 107
Using Lockout Method 1 (Read and Set Lock). . . . . . . . . . . . . . . . . 107
Using Lockout Method 2 (Password Enable). . . . . . . . . . . . . . . . . . 108
Modbus - Using Programmable Memory Blocks. . . . . . . . . . . . . . . . . 109
Software Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Chapter 10: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Troubleshooting Alarms, Errors and Control Issues. . . . . . . . . . . . . . . 113
Modbus - Programmable Memory Blocks. . . . . . . . . . . . . . . . . . . . . . 117
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Ordering Information for PID Controller Models . . . . . . . . . . . . . . . . . 121
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
How to Reach Us. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Watlow EZ-ZONE ® PM PID Controller
•
2 •
Table of Contents
1
Chapter 1: Overview
The EZ-ZONE ® PM takes the pain out of solving your thermal loop requirements.
Watlow’s EZ-ZONE PM controllers offer options to reduce system complexity and the cost of control-loop
ownership. You can order the EZ-ZONE PM as a PID controller or an over-under limit controller, or you can
combine both functions in the PM Integrated Limit Controller. You now have the option to integrate a highamperage power controller output, an over-under limit controller and a high-performance PID controller all in
space-saving, panel-mount packages. You can also select from a number of serial communications options to
help you manage system performance.
It just got a whole lot easier to solve the thermal requirements of your system. Because the EZ-ZONE PM
controllers are highly scalable, you only pay for what you need. So if you are looking for a PID controller, an
over-under limit controller or an integrated controller, the EZ-ZONE PM is the answer.
Standard Features and Benefits
Advanced PID Control Algorithm
• TRU-TUNE+ ® Adaptive tune provides tighter control for demanding applications.
• Auto Tune for fast, efficient start ups
High-amperage Power Control Output
• Drives 15 amp resistive loads directly
• Reduces component count
• Saves panel space and simplifies wiring
• Reduces the cost of ownership
EZ-ZONE configuration communications and software
• Saves time and improves the reliability of controller set up
Parameter Save & Restore Memory
• Reduces service calls and down time
Agency approvals: UL Listed, CSA, CE, RoHS, W.E.E.E. FM
• Assures prompt product acceptance
• Reduces end product documentation costs
• Semi F47-0200
P3T Armor Sealing System
• NEMA 4X and IP65 offers water and dust resistance, can be cleaned and washed down (indoor use only)
• Backed up by UL 50 independent certification to NEMA 4X specification
Three-year warranty
• Demonstrates Watlow’s reliability and product support
Touch-safe Package
• IP2X increased safety for installers and operators
Removable cage clamp wiring connectors
• Reliable wiring, reduced service calls
• Simplified installation
EZ-Key/s
Watlow EZ-ZONE ® PM PID Controller
•
3
•
Chapter 1 Over view
• Programmable EZ-Key enables simple one-touch operation of repetitive user activities
Programmable Menu System
• Reduces set up time and increases operator efficiency
Full-featured Alarms
• Improves operator recognition of system faults
• Control of auxiliary devices
Heat-Cool Operation
• Provides application flexibility with accurate temperature and process control
Profile Capability
• Preprogrammed process control
• Ramp and soak programming with four files and 40 total steps
A Conceptual View of the PM
The flexibility of the PM’s software and hardware allows a large range of configurations. Acquiring a better
understanding of the controller’s overall functionality and capabilities while at the same time planning out
how the controller can be used will deliver maximum effectiveness in your application.
It is useful to think of the controller in three parts: inputs; procedures; and outputs. Information flows
from an input to a procedure to an output when the controller is properly configured. A single PM controller
can carry out several procedures at the same time, for instance closed-loop control, monitoring for several different alarm situations and operating switched devices, such as lights and motors. Each process needs to be
thought out carefully and the controller’s inputs, procedures and outputs set up properly.
Inputs
The inputs provide the information that any given programmed procedure can act upon. In a simple form,
this information may come from an operator pushing a button or as part of a more complex procedure it may
represent a remote set point being received from another controller.
Each analog input typically uses a thermocouple or RTD to read the temperature of something. It can also
read volts, current or resistance, allowing it to use various devices to read humidity, air pressure, operator
inputs and others values. The settings in the Analog Input Menu (Setup Page) for each analog input must be
configured to match the device connected to that input.
Each digital input reads whether a device is active or inactive. A PM with digital input-output hardware
includes two sets of terminals each of which can be used as either an input or an output. Each pair of terminals must be configured to function as either an input or output with the Direction parameter in the Digital
Input/Output Menu (Setup Page).
The Function or EZ Key on the front panel of the PM also operates as a digital input by toggling the function assigned to it in the Digital Input Function parameter in the Function Key Menu (Setup Page).
Functions
Functions use input signals to calculate a value. A function may be as simple as reading a digital input to set
a state to true or false, or reading a temperature to set an alarm state to on or off. Or, it could compare the
temperature of a process to the set point and calculate the optimal power for a heater.
To set up a function, it’s important to tell it what source, or instance, to use. For example, an alarm may
be set to respond to either analog input 1 or 2 (instance 1 or 2, respectively).
Keep in mind that a function is a user-programmed internal process that does not execute any action outside
of the controller. To have any effect outside of the controller, an output must be configured to respond to a
function.
Outputs
Outputs can perform various functions or actions in response to information provided by a function, such as
operating a heater; turning a light on or off; unlocking a door; or turning on a buzzer.
Assign an output to a Function in the Output Menu or Digital Input/Output Menu. Then select which instance of that function will drive the selected output. For example, you might assign an output to respond to
alarm 4 (instance 4) or to retransmit the value of analog input 2 (instance 2).
Watlow EZ-ZONE ® PM PID Controller
•
4
•
Chapter 1 Over view
You can assign more than one output to respond to a single instance of a function. For example, alarm 2
could be used to trigger a light connected to output 1 and a siren connected to digital output 5.
Input Events and Output Events
Input and output events are internal states that are used exclusively by profiles. The source of an event input can come from a real-world digital input or an output from another function. Likewise, event outputs may
control a physical output such as an output function block or be used as an input to another function.
Getting Started Quickly
The PM control has a page and menu structure that is listed below along with a brief description of its purpose.
Setup Page
Push and hold the up and down keys (¿ ¯) for
6 seconds to enter. (See the Setup Page for further information)
Once received, a user would want to setup their control
prior to operation. As an example, define the input type
and set the output cycle time.
Operations Page
Push and hold the up and down keys (¿ ¯) for
3 seconds to enter. (See the Operations Page for
further information)
After setting up the control to reflect your equipment, the
Operations Page would be used to monitor or change runtime settings. As an example, the user may want to see
how much time is left in a profile step or perhaps change
the autotune set point.
Factory Page
Push and hold the Infinity and the green Advance keys (ˆ ‰) for 6 seconds to enter. (See
the Factory Page for further information)
For the most part the Factory Page has no bearing on the
control when running. A user may want to enable password protection, view the control part number or perhaps
create a custom Home Page.
Home Page
The control is at the Home Page when initially
powered up.
Pushing the green Advance key ‰ will allow the user to
see and change such parameters as the control mode, enable autotune and idle set point to name a few.
Profile Page
If equipped with this feature a user would want to go
Push and hold the the green Advance key ‰ for here to configure a profile.
6 seconds to enter. (See the Profile Page for further information)
The default PM loop configuration out of the box is shown below:
• Analog Input functions set to thermocouple, type J
•Heat algorithm set for PID, Cool set to off
•Output 1 set to Heat
•Control mode set to Auto
•Set point set to 75 °F
If you are using the input type shown above, simply connect your input and output devices to the control.
Power up the control and push the up arrow ¿ on the face of the control to change the set point from the
default value of 75 °F to the desired value. As the Set Point increases above the Process Value, output 1 will
come on and it will now begin driving your output device. The PV function as shown in the graphic below is
only available with PM4/8/9 models.
Note:
The output cycle time will have a bearing on the life of mechanical relay outputs and can be different based
on the type of output ordered. The output cycle time can be changed in the Setup Page under the Output
Menu.
EZ-ZONE PM Default Configuration
Input
Function
Input Sensor
Process
Value
Analog Input 1
Thermocouple Type J
PID
Controller
Heat
(PV)
Function
Output
Function
Output 1
Heat
Loop 1
Off
Watlow EZ-ZONE ® PM PID Controller
•
5
•
Chapter 1 Over view
EZ-ZONE® PM PID Model System Diagram
Universal Sensor Input, Configuration Communications,
Red/Green 7-Segment Display
Output
Functions
Input
Functions
Input sensor
None
Profile start/stop
Profile start
Profile hold/resume
Profile disable
TRU-TUNE+® disable
Control outputs off
Manual/auto mode
Tune
Idle set point
Force alarm
Loop & alarms off
Silence alarm
Alarm reset
Lock keypad
Restore user settings
Network
remote user interface,
personal computer,
programmable logic
controller, humanmachine interface
Analog Input 1
none, Thermocouple, RTD (100Ω,
1kΩ), Thermister 5kΩ, 10kΩ, 20kΩ,
40kΩ) Process (V, mV, mA) or 1k
Potentiometer
PID
Controller
Board
Slot A
ramp-soak
with 4 files
(optional)
Output 1 none, switched dc/open collector, form C mechanical (5 A) relay, form A
solid-state (0.5 A) relay, process (V, mA)
off, heat, cool,
duplex, alarm,
retransmit,
event
Output 2 none, switched dc, NO-ARC
power control (15 A), form A mechanical
(5 A) or Solid-State Relay (0.5 A)
off, heat, cool,
alarm, event
Digital Input (or Output) 5 & 6
(optional) none, switch, volts dc
EZ Key/s (PM4,6,8 and 9 only)
programmable event
Supervisory
&
Power
Board
Slot C
off, heat, cool,
alarm, event
Digital Output (or Input) 5 & 6
(optional) none, switched dc
EIA 485 Communications
Standard Bus, Modbus RTU (optional)
Output Status
Watlow EZ-ZONE ® PM PID Controller
•
6
•
1
2
3
4
5
6
Zone
Address
Indicates Zone
Address
Indicates I/O
Status
Chapter 1 Over view
2
Dimensions
Chapter 2: Install and Wire
1/32 DIN
15.9 mm
0.63 in
53.3 mm
2.10 in
101.6 mm
4.00 in
31.2 mm
1.23 in
30.9 mm
1.22 in
Side
Front
Top
44.96 to 45.47 mm
(1.77 to 1.79 inches)
Recommended panel spacing
22.2 to 22.5 mm
(0.87 to0.89 inches)
panel thickness 1.53 to 9.52 mm
(0.060 to 0.375)
21.6 mm
(0.85 in)
Minimum
21.6 mm
(0.85 in)
Minimum
Watlow EZ-ZONE ® PM PID Controller
•
7
•
Chapter 2 Install and Wire
1/16 DIN
15.8 mm
(0.62 in)
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
53.3 mm
(2.10 in)
Side
Front
51.2 mm
(2.02 in)
Top
L1
L3
K1
K3
99
J1
J3
CF
98
L2
L4
CD
K2
K4
CE
T1
T2
B5
S1
S2
D6
R1
R2
D5
Back
44.96 to 45.47 mm
(1.77 to 1.79 inches)
44.96 to 45.47 mm
(1.77 to 1.79 inches)
panel thickness 1.53 to 9.52 mm
(0.060 to 0.375)
21.6 mm
(0.85 in)
Minimum
21.6 mm
(0.85 in)
Minimum
Watlow EZ-ZONE ® PM PID Controller
•
8
•
Chapter 2 Install and Wire
1/8 DIN (PM8) Vertical
15.75 mm
(0.62 in)
1.52 mm
(0.06 in)
53.34 mm
(2.10 in)
100.33 mm
(3.95 in)
10.16 mm
(0.40 in)
30.73 mm
(1.21 in)
54.86 mm
(2.16 in)
101.60 mm
(4.00 in)
1/8 DIN (PM8) Vertical Recommended Panel Spacing
44.96 to 45.60 mm
(1.77 to 1.79 inches)
92.00 to 92.80 mm
(3.62 to 3.65 inches)
Panel thickness (0.060 in) 1.53 mm
to (0.375 in) 9.52 mm
21.6 mm
(0.85 in)
Minimum
21.6 mm
(0.85 in)
Minimum
Watlow EZ-ZONE ® PM PID Controller
•
9
•
Chapter 2 Install and Wire
1/8 DIN (PM9) Horizontal
15.75 mm
(0.62 in)
1.52 mm
(0.06 in)
100.33 mm
(3.95 in)
54.86 mm
(2.16 in)
53.34 mm
(2.10 in)
10.16 mm
(0.40 in)
30.73 mm
(1.21 in)
101.60 mm
(4.00 in)
1/8 DIN (PM9) Horizontal Recommended Panel Spacing
92.00 to 92.80 mm
(3.62 to 3.65 inches)
44.96 to 45.60 mm
(1.77 to 1.79 inches)
Panel thickness (0.060 in) 1.53 mm
to (0.375 in) 9.52 mm
21.6 mm
(0.85 in)
Minimum
21.6 mm
(0.85 in)
Minimum
Watlow EZ-ZONE ® PM PID Controller
•
10
•
Chapter 2 Install and Wire
1/4 DIN (PM4)
15.75 mm
(0.62 in)
1.52 mm
(0.06 in)
100.33 mm
(3.95 in)
100.33 mm
(3.95 in)
12.70 mm
(0.50 in)
30.73 mm
(1.21 in)
100.84 mm
(3.97 in)
1/4 DIN (PM4) Recommended Panel Spacing
92.0 to 93.0 mm
(3.62 to 3.65 inches)
92.0 to 93.0 mm
(3.62 to 3.65 inches)
21.6 mm
(0.85 inches)
Minimum
Panel thickness .060 (1.53) to .375 (9.52)
21.6 mm
(0.85 inches)
Minimum
Watlow EZ-ZONE ® PM PID Controller
•
11
•
Chapter 2 Install and Wire
Installation
Don't be afraid to apply enough pressure to properly install the controller. The seal system is
compressed more by mating the mounting collar
tighter to the front panel (see pictures above). If
you can move the case assembly back and forth
in the cutout, you do not have a proper seal.
The tabs on each side of the mounting collar have
teeth that latch into the ridges on the sides of the
controller. Each tooth is staggered at a different
depth from the front so that only one of the tabs,
on each side, is locked onto the ridges at a time.
panel
bezel
retention collar
gasket
case
Note:
There is a graduated measurement difference between the upper and lower half of the display to
the panel. In order to meet the seal requirements
mentioned above, ensure that the distance from the
front of the top half of the display to the panel is
16 mm (0.630 in.) or less, and the distance from the
front of the bottom half and the panel is 13.3 mm
(0.525 in.) or less.
panel
retention collar
bezel
gasket
case
Removing the Mounted Controller from Its Case
1. From the controller's face, pull out the tabs on
each side until you hear it click.
1. Make the panel cutout using the mounting template dimensions in this chapter.
Insert the case assembly into the panel cutout.
2. While pressing the case assembly firmly against
the panel, slide the mounting collar over the back
of the controller.
If the installation does not require a NEMA 4X
seal, simply slide together until the gasket is
compressed.
Pull out the tab on each side
until you hear it click.
Grab the unit above and
below the face and pull forward.
2. On a PM6 control once the sides are released
grab the unit above and below the face with two
hands and pull the unit out. On the PM4/8/9 controls slide a screwdriver under the pry tabs and
turn.
çWarning:
• This equipment is suitable for use in class 1, div.
2, Groups A, B, C and D or Non-Hazardous locations only. Temperature Code T4A.
Slide the mounting collar over Place the blade of a screwthe back of the controller.
driver in the notch of the
mounting collar assembly.
• WARNING – EXPLOSION HAZARD. Substitution of component may impair suitability for class
1, div. 2.
3. For a NEMA 4X (UL50, IP65) seal, alternately
place and push the blade of a screwdriver against
each of the the four corners of the mounting collar assembly. Apply pressure to the face of the
controller while pushing with the screwdriver.
Watlow EZ-ZONE ® PM PID Controller
•
• WARNING – EXPLOSION HAZARD. Do not
disconnect equipment unless power has been
switched off or the area is known to be nonhazardous.
12
•
Chapter 2 Install and Wire
Returning the Controller to its Case
1. Ensure that the orientation of the controller is
correct and slide it back into the housing.
Note: The controller is keyed so if it feels that it will not
slide back in do not force it. Check the orientation again
and reinsert after correcting.
2. Using your thumbs push on either side of the controller until both latches click.
Chemical Compatibility
This product is compatible with acids, weak alkalis,
alcohols, gamma radiation and ultraviolet radiation.
This product is not compatible with strong alkalis,
organic solvents, fuels, aromatic hydrocarbons, chlorinated hydrocarbons, esters and keytones.
çWarning:
All electrical power to the controller and controlled
circuits must be disconnected before removing the
controller from the front panel or disconnecting
other wiring.
Failure to follow these instructions may cause an
electrical shock and/or sparks that could cause an
explosion in class 1, div. 2 hazardous locations.
Watlow EZ-ZONE ® PM PID Controller
•
13
•
Chapter 2 Install and Wire
Wiring
Terminal Definitions for Slots A
Slot A
Output
Terminal Function
Configuration
common (Any switched dc output can use this common.)
dc- (open collector)
dc+
Switched dc/open collector
output 1: PM _ _ _ [C] _-_ AAAA _ _
dcdc+
Switched dc
output 2: PM _ _ _ _ [C]-_ AAAA _ _
F1
G1
H1
voltage or current voltage +
current +
Universal Process
output 1: PM _ _ _ [F] _-_ AAAA _ _
L1
K1
J1
normally open
common
normally closed
Mechanical Relay 5 A, Form C
output 1: PM _ _ _ [E] _-_ AAAA _ _
L2
K2
normally open
common
NO-ARC 15 A, Form A
output 2: PM[4, 6, 8, 9] _ _ _ [H]-_ AAAA _ _
L2
K2
normally open
common
Mechanical Relay 5 A, Form A
output 2: PM _ _ _ _ [J]-_ AAAA _ _
L2
K2
normally open
common
Solid-state Relay 0.5 A, Form A
output 1: PM _ _ _ [K] _-_ AAAA _ _
output 2: PM _ _ _ _ [K]-_ AAAA _ _
S2 (RTD) or current +
S3 (RTD), thermocouple -, current -, volts - or potentiometer wiper, thermistor
S1 (RTD), thermocouple + or volts +, thermistor, potentiometer
Universal / Thermistor Input
input 1: all configurations
1
2
X1
W1
Y1
W2
Y2
L1
K1
Inputs
1
T1
S1
R1
Slot A
Terminal Definitions for Slot C
Slot C
Terminal Function
Configuration
98
99
power input: ac or dc+
power input: ac or dc-
all
CC
CA
CB
Standard Bus or Modbus RTU EIA-485 common
Standard Bus or Modbus RTU EIA-485 T-/RStandard Bus or Modbus RTU EIA-485 T+/R+
Standard Bus or Modbus
PM _ _ _ _ _-[1] AAAA _ _
CF
CD
CE
Standard Bus EIA-485 common
Standard Bus EIA-485 T-/RStandard Bus EIA-485 T+/R+
PM _ _ _ _ _-[A] AAAA _ _
B5
D6
D5
digital input-output common
digital input or output 6
digital input or output 5
PM _ _ [2]_ _-_ AAAA _ _
PM _ _ [4] _ _-_ AAAA _ _
Back View
Slot Orientation
1/16 DIN PM6
Back View
Slot Orientation
1/32 DIN PM3
Output 2
Input 1
A
B
C
Watlow EZ-ZONE ® PM PID Controller
485 Comms
Dig I/O 5 & 6
C
Dig I/O 5 & 6 485 Comms
Output 1
Power
Power
A
Output 1
•
14
•
Output 2
Input 1
Chapter 2 Install and Wire
Back View
Slot Orientation 1/8
DIN Vertical PM8
Power
A
C
E
D
B
Dig I/O 5 & 6 485 Comms
Dig I/O 5 & 6 485 Comms
C
Input 1
Input 1
E
Output 2
Output 2
A
Output 1
Output 1
Power
Back View
Slot Orientation
1/8 DIN Horizontal PM9
Input 1
A
D
E
C
Dig I/O 5 & 6 485 Comms
Communications Card
Output 2
Digital I/O 7 - 12
Output 1
D
B
Power
Back View
Slot Orientation
1/4 DIN Horizontal PM4
Output 3
Output 4
Input 2
B
EZ-ZONE PM Isolation Blocks
Digital Inputs & Outputs
5-6
No Isolation
Switched DC, Open Collector,
Process outputs
No Isolation
Analog Input 1
Safety Isolation
Safety Isolation
Controller Power Supply
12 to 40VÎ (dc)
20 to 28VÅ (ac)
100 to 240VÅ (ac)
No Isolation
Controller
Low Voltage Power Bus
Note:
Mechanical Relay,
Solid-State Relay,
NO-ARC Relay
Outputs
Analog Input 1 can be optionally ordered as
an isolated input (see ordering information
in the back of this User’s Guide).
Safety Isolation
Low-voltage
Isolation
Communications Ports
Low-voltage Isolation: 42V peak
Safety Isolation: 2300VÅ (ac)
Watlow EZ-ZONE ® PM PID Controller
•
15
•
Chapter 2 Install and Wire
Warning:
Óç
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
Low Power
Slot C
98
99
Note:
Adjacent terminals may be labeled
differently, depending on the model
number.
Note:
To prevent damage to the controller, do not connect wires to unused
terminals.
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
Note:
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
power
fuse
• Minimum/Maximum Ratings
• 12 to 40VÎ (dc)
• 20 to 28VÅ (ac) Semi Sig F47
• 47 to 63 Hz
• 14VA maximum power consumption (PM4,8 & 9)
• 10VA maximum power consumption (PM3 & 6)
PM_ _ [3,4] _ _ - _ _ _ _ _ _ _
CF
CD
CE
B5
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
power
D6
D5
Power
High Power
Slot C
98
99
power
power
fuse
CF
CD
CE
B5
D6
• Minimum/Maximum Ratings
• 85 to 264VÅ (ac)
• 100 to 240VÅ (ac) Semi Sig F47
• 47 to 63 Hz
• 14VA maximum power consumption (PM4,8 & 9)
• 10VA maximum power consumption (PM3 & 6)
PM_ _ [1,2] _ _ - _ _ _ _ _ _ _
D5
Power
Digital Input 5, 6
Voltage Input
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
Slot C
98
Warning: ç
Warning:
ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
CF
CD
CE
common
B5
DC Input
D6
DC Input
D_
Dry Contact
Dry Contact
• Input inactive when >
500 Ω
• Input active when < 100 Ω
• maximum short circuit 13
mA
PM_ _ [2,4] _ _-_ _ _ _ _ _ _
D5
ç
Warning:
Explosion Hazard - Do not discon-
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
Watlow EZ-ZONE ® PM PID Controller
Vdc
DC Voltage
• Input not to exceed 36V at
3 mA
• Input active when > 3V @
0.25 mA
• Input inactive when < 2V
99
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
common
B_
Digital Input
• Update rate 10 Hz
• Dry contact or dc voltage
B_
common
D_
24 Vdc
•
16
•
Chapter 2 Install and Wire
Warning:
Óç
Input 1 Thermocouple
Slot A
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
-
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
Note:
• 2 kΩ maximum source resistance
• >20 MΩ input impedance
• 3 microampere open-sensor detection
• Thermocouples are polarity sensitive. The negative lead (usually
red) must be connected to S1.
• To reduce errors, the extension wire for thermocouples must be
of the same alloy as the thermocouple.
PM _ _ _ _ _-_ AAAA _ _
S1
+
R1
Input 1 RTD
Slot A
Adjacent terminals may be labeled
differently, depending on the model
number.
Slot A
Note:
To prevent damage to the controller, do not connect wires to unused
terminals.
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
S2
T1
S3
S1
S3
S1
S1
R1
S1
R1
3-wire
2-wire
• platinum, 100 and 1,000 Ω @ 0°C
• calibration to DIN curve (0.00385 Ω/Ω/°C)
• 20 Ω total lead resistance
• RTD excitation current of 0.09 mA typical. Each
ohm of lead resistance may affect the reading by
0.03°C.
• For 3-wire RTDs, the S1 lead (usually white) must
be connected to R1.
• For best accuracy use a 3-wire RTD to compensate
for lead-length resistance. All three lead wires must
have the same resistance.
PM _ _ _ _ _-_ AAAA _ _
Note:
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
Input 1 Process
Slot A
Slot A
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
Warning:
ç
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
Warning:
ç
• 0 to 20 mA @ 100 Ω input impedance
• 0 to 10VÎ (dc) @ 20 kΩ input impedance
• 0 to 50 mVÎ (dc) @ 20 kΩ input impedance
•scalable
PM _ _ _ _ _-_ AAAA _ _
+ T1
-
- S1
+ R1
S1
amperes
volts
Input 1 Potentiometer
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
Slot A
ç
Warning:
Explosion Hazard - Do not discon-
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
• Use a 1 kΩ potentiometer.
PM _ _ _ _ _-_ AAAA _ _
CW
CCW
S1
R1
Watlow EZ-ZONE ® PM PID Controller
•
17
•
Chapter 2 Install and Wire
Warning:
Óç
Input 1 Thermistor
Slot A
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
• >20 MΩ input impedance
• 3 microampere open-sensor detection
Input 1: PM _ [J,N,E*] _ _ _ _-_ _ _ _ _ _ _ (S1/
R1)
*PM4,8 & 9 only
Note:
S1
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
Note:
Adjacent terminals may be labeled
differently, depending on the model
number.
R1
Digital Output 5, 6
Slot C
98
Note:
99
To prevent damage to the controller, do not connect wires to unused
terminals.
CF
CD
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
CE
B5
D6
Note:
D5
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
Warning:
D5
24VÎ (dc)
D6
B5
Internal Circuitry
Switched DC Wiring Example Using DO 5 and 6
switched dc outputs
Warning: ç
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
switched dc outputs
* Output 5 only
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
Digital Output
• SSR drive signal
• Update rate 10 Hz
• Maximum open circuit voltage is 22 to 25VÎ (dc)
• PNP transistor source
• Typical drive; 21mA @ 4.5V
for DO5, and 11mA @ 4.5V
for DO6
• Current limit 24mA for Output 5 and 12mA Output 6
• Output 5 capable of driving
one 3-pole DIN-A-MITE
• Output 6 capable of driving
one 1-pole DIN-A-MITE
PM _ _ [2,4] _ _-_ _ _ _ _ _ _
D5
24VÎ (dc)
Htr 2
ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
ç
Htr 1
D6
B5
Internal Circuitry
+
+
-
DC80-60C0-0000
Warning:
Explosion Hazard - Do not discon-
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
Watlow EZ-ZONE ® PM PID Controller
•
18
•
Chapter 2 Install and Wire
Warning:
Óç
DO5 Output Curve Volts mA 25.0 Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
20.0 15.0 10.0 Note:
Note:
5.0 0 70 140 210 280 350 420 490 560 630 700 770 840 910 980 1050 1120 1190 1260 1330 1400 1470 1540 1610 1680 1750 1820 1890 1960 2030 2100 2170 2240 2310 2380 2450 2520 2590 2660 2730 2800 2870 2940 3100 3800 4500 5200 5900 6600 7300 8000 Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
0.0 Resistance in Ohms Adjacent terminals may be labeled
differently, depending on the model
number.
DO6 Output Curve Volt mA 25.0 Note:
To prevent damage to the controller, do not connect wires to unused
terminals.
20.0 Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
15.0 10.0 Note:
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
0 70 140 210 280 350 420 490 560 630 700 770 840 910 980 1050 1120 1190 1260 1330 1400 1470 1540 1610 1680 1750 1820 1890 1960 2030 2100 2170 2240 2310 2380 2450 2520 2590 2660 2730 2800 2870 2940 3100 3800 4500 5200 5900 6600 7300 8000 Note:
This Equipment is suitable for use in
5.0 0.0 Resistance in Ohms CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
Warning:
ç
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
Warning:
ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
ç
Warning:
Explosion Hazard - Do not discon-
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
Quencharc Note:
Switching pilot duty inductive loads
(relay coils, solenoids, etc.) with the
mechanical relay, solid state relay or
open collector output options requires
use of an R.C. suppressor.
Watlow EZ-ZONE ® PM PID Controller
•
19
•
Chapter 2 Install and Wire
Warning:
Óç
Output 1 Switched DC/Open Collector
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
Slot A
common
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
dc - (open collector)
dc +
X1
W1
Y1
Note:
Adjacent terminals may be labeled
differently, depending on the model
number.
Open Collector
• 100 mA maximum output current sink
•30VÎ (dc) max. supply voltage
• Any switched dc output can use
the common terminal.
• Use an external power supply to
control a dc load, with the load
positive to the positive of the
power supply, the load negative
to the open collector and common to the power supply negative.
See Quencharc note.
PM _ _ _ [C] _-_ AAAA _ _
Note:
To prevent damage to the controller, do not connect wires to unused
terminals.
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
Note:
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
Warning:
normally open
ç
ç
Warning:
Explosion Hazard - Do not discon-
common
normally closed
common
W1
dc -
24V
Y1
dc +
Open Collector
Power Supply
common
X1
W1
dc -
24V
Load
Y1
L1
K1
J1
• 5 A at 240VÅ (ac) or 30VÎ (dc)
maximum resistive load
• 20 mA at 24V minimum load
• 125 VA pilot duty at 120/240VÅ
(ac), 25 VA at 24VÅ (ac)
• 100,000 cycles at rated load
• Output does not supply power.
• for use with ac or dc
See Quencharc note.
PM _ _ _ [E] _-_ AAAA _ _
L1
normally open
K1
common
J1
normally closed
Output 1 Universal Process
Slot A
volts or current -
F1
volts +
G1
current +
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
H1
Quencharc Note:
Switching pilot duty inductive loads
(relay coils, solenoids, etc.) with the
mechanical relay, solid state relay or
open collector output options requires
use of an R.C. suppressor.
X1
Slot A
ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
Switched DC
Output 1 Mechanical Relay, Form C
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
Warning:
Switched DC
•·Maximum open circuit voltage
is 22 to 25VÎ (dc)
• 30mA max. per single output /
40mA max. total per paired outputs (1 & 2)
• Typical drive; 4.5VÎ (dc) @ 30
mA
• Short circuit limited to <50 mA
• NPN transistor sink
• Use dc- and dc+ to drive external solid-state relay
• 1-pole DIN-A-MITE: up to 4 in
parallel or 4 in series
• 2-pole DIN-A-MITE: up to 2 in
parallel or 2 in series
• 3-pole DIN-A-MITE: up to 2 in
series
• 0 to 20 mA into 800 Ω maximum load
• 0 to 10VÎ (dc) into 1 kΩ minimum load
•scalable
• output supplies power
• cannot use voltage and current
outputs at same time
• Output may be used as retransmit or control.
PM _ _ _ [F] _-_ AAAA _ _
Universal Process
(Output 1)
Watlow EZ-ZONE ® PM PID Controller
•
20
•
F1
negative
0 to 10 V
4 to 20 mA
G1
volts +
H1
current +
Chapter 2 Install and Wire
Warning:
Óç
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
Output 1 Solid-State Relay, Form A
Slot A
normally open
L1
common
K1
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
• 0.5 A at 20 to 264VÅ (ac) maximum resistive load
• 20 VA 120/240VÅ (ac) pilot duty
• opto-isolated, without contact
suppression
• maximum off state leakage of
105 microamperes
• output does not supply power
• Do not use on dc loads.
• See Quencharc note.
PM _ _ _ [K] _-_ AAAA _ _
1 Amp SSR Derating Curve
1
Adjacent terminals may be labeled
differently, depending on the model
number.
0.9
To prevent damage to the controller, do not connect wires to unused
terminals.
Safe Operating Area
Amps RMS
0.8
Note:
0.7
0.6
0.5
0.4
0.3
0.2
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
Note:
0.1
0
-20
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
dcdc+
W2
Y2
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
ç
20
30
40
50
60
70
common
W2
dc -
24V
Y2
dc +
Output 2 NO-ARC Relay, Form A
Slot A
Warning: ç
Explosion Hazard - Do not discon-
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
10
Ambient Temperature (oC)
• Maximum open circuit voltage is 22 to 25VÎ (dc)
• 30mA max. per single output / 40mA max. total per
paired outputs (1 & 2)
• Typical drive; 4.5VDC @ 30
mA
• Short circuit limited to <50
mA
• NPN transistor sink
• Use dc- and dc+ to drive
external solid-state relay
• 1-pole DIN-A-MITE: up to 4
in parallel or 4 in series
• 2-pole DIN-A-MITE: up to 2
in parallel or 2 in series
• 3-pole DIN-A-MITE: up to 2
in series
PM _ _ _ _ [C]-_ AAAA _ _
Slot A
ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
0
-10
Output 2 Switched DC
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
Warning:
K1
1.1
Note:
Warning:
L1
normally open
common
Quencharc Note:
Switching pilot duty inductive loads
(relay coils, solenoids, etc.) with the
mechanical relay, solid state relay or
open collector output options requires
use of an R.C. suppressor.
Watlow EZ-ZONE ® PM PID Controller
L2
K2
• 15 A at 85 to 264VÅ (ac) resistive load only
• 2,000,000 cycle rating for NOARC circuit
• 100 mA minimum load
• 2 mA maximum off state leakage
• Do not use on dc loads.
• Output does not supply power.
PM [4, 6, 8, 9] _ _ _ [H]-_ AAAA
__
•
21
•
L2
K2
Chapter 2 Install and Wire
Warning:
Óç
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
Output 2 Mechanical Relay, Form A
Slot A
normally open
common
• 5 A at 240VÅ (ac) or 30VÎ (dc)
maximum resistive load
• 20 mA at 24V minimum load
• 125 VA pilot duty @ 120/240VÅ
(ac), 25 VA at 24VÅ (ac)
• 100,000 cycles at rated load
• Output does not supply power.
• for use with ac or dc
See Quencharc note.
PM _ _ _ _ [J]-_ AAAA _ _
L2
K2
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
Slot A
Adjacent terminals may be labeled
differently, depending on the model
number.
K1
J1
normally open
L2
common
K2
Note:
Note:
• 0.5 A at 20 to 264VÅ (ac) maximum resistive load
• 20 VA 120/240VÅ (ac) pilot duty
• opto-isolated, without contact
suppression
• maximum off state leakage of
105 microamperes
• Output does not supply power.
• Do not use on dc loads.
See Quencharc note.
PM _ _ _ _ [K]-_ AAAA _ _
L1
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
T1
S1
R1
Solid-state Relay
(Ouput 2)
1
0.9
0.8
ç
Warning:
Explosion Hazard - Do not discon-
Amps RMS
0.7
0.6
0.5
0.4
0.3
Warning: ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
Safe Operating Area
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
ç
K2
1.1
Note:
This Equipment is suitable for use in
Warning:
L2
1 Amp SSR Derating Curve
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
K2
Output 2 Solid-State Relay, Form A
Note:
To prevent damage to the controller, do not connect wires to unused
terminals.
L2
0.2
0.1
0
-20
0
-10
10
20
30
40
o
Ambient Temperature ( C)
50
60
70
Quencharc Wiring Example
In this example the Quencharc circuit (Watlow
part# 0804-0147-0000) is used to protect PM
internal circuitry from the counter electromagnetic force from the inductive user load
when de-engergized. It is recommended that
this or an equivalent Quencharc be used when
connecting inductive loads to PM outputs.
User Load
L_
N
Quencharc
K_
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
Quencharc Note:
Switching pilot duty inductive loads
(relay coils, solenoids, etc.) with the mechanical relay, solid state relay or open
collector output options requires use of
an R.C. suppressor.
Watlow EZ-ZONE ® PM PID Controller
•
22
•
Chapter 2 Install and Wire
Warning:
Óç
Standard Bus EIA-485 Communications
Slot C
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
98
99
CF common
CD
CE
D6
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
Note:
Adjacent terminals may be labeled
differently, depending on the model
number.
Note:
To prevent damage to the controller, do not connect wires to unused
terminals.
Note:
Standard Bus
EIA-485
Note:
Do not leave a USB to EIA-485 converter connected to Standard Bus without power (i.e., disconnecting the USB end from the computer while leaving
the converter connected on Standard Bus). Disturbance on the Standard
Bus may occur.
Modbus RTU or Standard Bus EIA-485 Communications
Slot C
98
99
CC common
CA
CB
Note:
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
ç
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
ç
Note:
A 120 Ω termination resistor
may be required across T+/R+
and T-/R-, placed on the last
controller on the network.
D5
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
Warning:
T+/R+
B5
Note:
Warning:
T-/R-
• Do not connect more than 16
EZ-ZONE PM controllers on a
network.
• maximum network length:
1,200 meters (4,000 feet)
• 1/8th unit load on EIA-485 bus
PM _ _ _ _ _-[A] AAAA _ _
• Wire T-/R- to the A terminal of
the EIA-485 port.
• Wire T+/R+ to the B terminal of
the EIA-485 port.
• Wire common to the common
terminal of the EIA-485 port.
• Do not route network wires
with power wires. Connect network wires in daisy-chain fashion when connecting multiple
devices in a network.
T-/RT+/R+
B5
D6
D5
• Only one protocol per port is
available at a time: either Modbus RTU or Standard Bus.
• Do not connect more than 16
EZ-ZONE PM controllers on a
Standard Bus network.
• Do not connect more than 247
EZ-ZONE PM controllers on a
Modbus RTU network.
• maximum network length:
1,200 meters (4,000 feet)
• 1/8th unit load on EIA-485 bus.
PM _ _ _ _ _-[1] AAAA _ _
• Wire T-/R- to the A terminal of
the EIA-485 port.
• Wire T+/R+ to the B terminal of
the EIA-485 port.
• Wire common to the common
terminal of the EIA-485 port.
• Do not route network wires
with power wires. Connect network wires in daisy-chain fashion when connecting multiple
devices in a network.
• A termination resistor may be
required. Place a 120 Ω resistor
across T+/R+ and T-/R- of last
controller on network.
Modbus RTU or EIA/TIA-485
Modbus-IDA
Terminal
Standard
Bus EIA-485 Name
Watlow
Terminal
Label
Function
DO
A
CA or CD
T-/R-
D1
B
CB or CE
T+/R+
common
common
CC or CF
common
Note:
Do not leave a USB to EIA-485 converter connected to Standard Bus
without power (i.e., disconnecting
the USB end from the computer
while leaving the converter connected on Standard Bus). Disturbance
on the Standard Bus may occur.
Wiring a Serial EIA-485 Network
Two example networks are shown below where the first one is using Watlow's Standard Bus and the other showing connections over Modbus. Do not
route network wires with power wires. Connect network wires in daisy-chain
fashion when connecting multiple devices in a network. A termination resistor may be required. Place a 120 Ω resistor across T+/R+ and T-/R- of the last
controller on a network. Only one protocol per port is available at a time: either Modbus RTU or Standard Bus.
Warning:
Explosion Hazard - Do not discon-
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
Watlow EZ-ZONE ® PM PID Controller
•
23
•
Chapter 2 Install and Wire
Warning:
Óç
A Network Using Watlow's Standard Bus and an RUI/Gateway
Power
Supply
EZ-ZONE ST
ST_ _ - (B or F) _ M _ -_ _ _ _
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
EZ-ZONE RM
fuse
98
99
CF
CE
CD
B5
D6
D5
-A
+B
power
power
common
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
98
99
EZ-ZONE PM
Note:
Adjacent terminals may be labeled
differently, depending on the model
number.
power
com
-A
CD
+B
CE
CF
B5
Slot C
D6
RUI/Gateway
EZKB-_ A _ _- _ _ _ _
power
common
-A
CD
+B
99
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
Note:
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
CZ
CX
CY
Power
Supply
EZ-ZONE ST
ST_ _ - (B or F) _ M _ -_ _ _ _
EZ-ZONE RM
fuse
98
99
CC
CA
B5
CB
D6
D5
-A
+B
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
CE
A Network Using Modbus RTU.
ç
ç
-A
+B
CE
power
power
common
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
Warning:
common
CF
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
99
98
Note:
Warning:
power
To prevent damage to the controller, do not connect wires to unused
terminals.
CD
98
Note:
CF
D5
98
99
EZ-ZONE PM
PM_ _ _ _ _-1AAAAXX
CC
CA
CB
power
power
com
-A
+B
B5
Slot C
D6
Watlow EZ-ZONE ® PM PID Controller
CY
CZ
CX
CA
CB
power
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
99
98
ç
Warning:
Explosion Hazard - Do not discon-
CC
D5
power
power
common
-A
+B
PLC
•
24
•
common
-A
+B
Chapter 2 Install and Wire
Warning:
Óç
USB
Port
Slot C
Slot B
Slot A
Slot C
Slot B
Note:
Maximum wire size termination and
torque rating:
• 0.0507 to 3.30 mm2 (30 to 12
AWG) single-wire termination or
two 1.31 mm2 (16 AWG)
• 0.56 Nm (5.0 lb.-in.) torque
Address 2
Address 1
Slot A
Use National Electric (NEC) or other
country-specific standard wiring and
safety practices when wiring and
connecting this controller to a power
source and to electrical sensors or
peripheral devices. Failure to do so
may result in damage to equipment
and property, and/or injury or loss
of life.
Connecting a Computer to PM Controls Using B&B 485 to USB Converter
Data Format
38,400 baud
8 data bits
no parity
1 start bit
1 stop bit
PC Software Protocol - Standard Bus
EZ-ZONE Configurator software
Note:
Adjacent terminals may be labeled
differently, depending on the model
number.
Note:
To prevent damage to the controller, do not connect wires to unused
terminals.
Note:
Maintain electrical isolation between
analog input 1, digital input-outputs,
switched dc/open collector outputs
and process outputs to prevent
ground loops.
Note:
The control output common terminal and the digital common terminal
are referenced to different voltages
and must remain isolated.
Note:
This Equipment is suitable for use in
CLASS I, DIVISION 2, Groups A, B,
C and D or Non-Hazardous locations
only. Temperature Code T4A
Warning:
Use twisted pair wires such as Cat 5 cabling. Do not route with power carrying
conductors. Daisy chain wire up to 16 EZ-ZONE devices.
0847-0326-0000
Note:
Do not leave a USB to EIA-485 converter connected to Standard Bus without
power (i.e., disconnecting the USB end from the computer while leaving the
converter connected on Standard Bus). Disturbance on the Standard Bus
may occur.
Note:
When connecting the USB converter to the PC it is suggested that the Latency Timer be changed from the default of 16 msec to 1 msec. Failure to
make this change may cause communication loss between the PC running
ZE-ZONE Configurator software and the control.
To modify Latency Timer settings follow the steps below:
1. Navigate to Device Manager.
2. Double click on Ports.
3. Right click on the USB serial port in use and select Properties.
4. Click the tab labeled Port settings and then click the Advance button.
ç
Explosion Hazard - Dry contact closure Digital Inputs shall not be used
in Class I Division 2 Hazardous Locations unless switch used is approved
for this application.
Warning:
ç
Explosion Hazard – Substitution of
component may impair suitability
for CLASS I, DIVISION 2.
ç
Warning:
Explosion Hazard - Do not discon-
nect while the circuit is live or
unless the area is known to be free
of ignitable concentrations of flammable substances.
Watlow EZ-ZONE ® PM PID Controller
•
25
•
Chapter 2 Install and Wire
3
Chapter 3: Keys and Displays
Upper (Left, 32nd DIN) Display:
1/32 DIN (PM3)
In the Home Page, displays the process
value, otherwise displays the value of
the parameter in the lower display.
Zone Display:
Indicates the controller zone.
®
1 2
1/16 DIN (PM6)
A = zone 10
b = zone 11
C = zone 12
d = zone 13
E = zone 14
F = zone 15
h = zone 16
Percent Units:
Profile Activity:
EZ Key/s:
1/8 DIN (PM9) Horizontal
Lights when the controller is displaying values as a percentage or
when the Manual Power is displayed.
Channel Display:
Indicates the set point or output
power value during operation, or
the parameter whose value appears in the upper display.
Lights when a profile is running.
Flashes when a profile is paused.
®
1 to 9 = zones 1 to 9
Lower (Right, 32nd DIN) Display:
This key can be programmed to do
various tasks, such as locking the
keyboard, restoring user settings,
etc...
®
Output Activity:
Number LEDs indicate activity of
outputs. A flashing light indicates
output activity.
1/8 DIN (PM8) Vertical
Indicates the channel for any given
EZ-ZONE module.
Communications Activity
Flashes when another device is
communicating with this controller.
®
- Available with the PM4, 8 and PM9 only.
Temperature Units:
Indicates whether the temperature is displayed in Fahrenheit or
Celsius.
Infinity Key ˆ
Press to back up one level, or press and
hold for two seconds to return to the
Home Page. From the Home Page can
clear alarms and errors if clearable.
Up and Down Keys ¿ ¯
1/4 DIN (PM4)
®
In the Home Page, adjusts the set
point in the lower display. In other
pages, changes the upper display to a higher or lower value, or
changes a parameter selection.
Advance Key ‰
Advances through parameter prompts.
Watlow EZ-ZONE ® PM PID Controller
Note:
Upon power up, the upper or
left display will briefly indicate the firmware revision
and the lower or right display
will show PM representing
the model.
•
26
•
Chapter 3 Keys and Displays
Responding to a Displayed Message
An active message will cause the display to toggle between the normal settings and the active message in the
upper display and [Attn] in the lower display.
Your response will depend on the message and the controller settings. Some messages, such as Ramping and
Tuning, indicate that a process is underway. If the message was generated by a latched alarm and the condition no longer exists or if an alarm has silencing enabled it can be silenced simply by pushing the Infinity ˆ
key. Alternatively, use the method below to view all and then clear.
Push the Advance Key to display [ignr] in the upper display and the message source (such as [al;h1]) in the
lower display.Use the Up ¿ or Down ¯ keys to scroll through possible responses, such as Clear [`CLr] or Silence [`SiL]. Then push the Advance ‰ or Infinity ˆ key to execute the action. See the Home Page for further information on the Attention Codes.
Display
[Attn]
Parameter Name
Description
Range
Attention
An active message will cause
the display to toggle between
the normal settings and the
active message in the upper
display and [Attn] in the
lower display.
Your response will depend on
the message and the controller settings. Some messages,
such as Ramping and Tuning, indicate that a process is
underway. If the message was
generated by a latched alarm
or limit condition, the message
can be cleared when the condition no longer exists. If an
alarm has silencing enabled, it
can be silenced.
Push the Advance Key to display [ignr] in the upper display and the message source
(such as [Li;h1]) in the lower
display.
Use the Up ¿ or Down ¯ keys
to scroll through possible responses, such as Clear [`CLr]
or Silence [`SiL]. Then push
the Advance ‰ or Infinity
ˆ key to execute the action.
Alternatively, rather than
scrolling through all messages
simply push the Infinity ˆ
button to generate a clear.
Watlow EZ-ZONE ® PM PID Controller
•
Appears If
an alarm or error mes[AL;L1] [AL;L2] [AL;L3] [AL;L4]
sage is active.
Alarm Low 1 to 4
[AL;h1] [AL;h2] [AL;h3] [AL;h4]
Alarm High 1 to 4
[AL;E1] [AL;E2] [AL;E3] [AL;E4]
Alarm Error 1 to 4
[Er;i1] Error Input 1
[tUn1] Tuning 1
[`rP1] Ramping 1
[LP;o1] Loop Open Error 1
[LP;r1] Loop Reversed Error 1
[uAL;h] Value to high to be displayed
in 4 digit LED display
[uAL;L] Value to low to be displayed in
4 digit LED display
27
•
Chapter 3 Keys and Displays
4
Chapter 4: Home Page
Default Home Page Parameters
Watlow’s patented user-defined menu system improves operational efficiency. The user-defined Home Page
provides you with a shortcut to monitor or change the parameter values that you use most often. The default
Home Page is shown on the following page. When a parameter normally located in the Setup Page or Operations Page is placed in the Home Page, it is accessible through both. If you change a parameter in the Home
Page, it is automatically changed in its original page. If you change a parameter in its original page it is automatically changed in the Home Page.
The Attention [Attn] parameter appears only if there is an active message. An example of an active message could be an Input Error [er;i1], or it could be for information only like Autotune [tUN1] taking place.
Use the Advance Key ‰to step through the other parameters. When not in pairs the parameter prompt
will appear in the lower display, and the parameter value will appear in the upper display. You can use the
Up ¿ and Down ¯ keys to change the value of writable parameters, just as you would in any other menu.
Note:
If a writable value is placed on the upper display and is paired with another read only parameter on the
lower display, the arrow keys affect the setting of the upper display. If two writable parameters are paired,
the arrow keys affect the lower display.
If Control Mode is set to Auto, the Process Value is in the upper display and the Set Point (read-write) is
in the lower display.
If a profile is running, the process value is in the upper display and the Target Set Point (read only) is in
the lower display. If Control Mode is set to Manual, the Process Value is in the upper display and the output
power level (read-write) is in the lower display.
If Control Mode is set to Off, the Process Value is in the upper display and [`oFF] (read only) is in the
lower display.
If a sensor failure has occurred, [----] is in the upper display and the output power level (read-write) is
in the lower display.
Changing the Set Point
You can change the set point by using the Up ¿ or Down ¯ keys when a profile is not running.
Starting a Profile from the Home Page
1. When at the Home Page, press the Advance Key ‰ to locate Profile Start and select the file or step num-
ber to start. The upper display will show [```1] and the lower display will show [ p ; s t1] .
2. Press the Up ¿ or Down ¯ key to choose the file or step number.
3. Press the Advance Key ‰ to select the Profile Action Request. The upper display will show [none] and
the lower display will show [ p ; a C1] .
4. Press the Up ¿ or Down ¯ keys to select the Profile Start. The upper display will show [Prof] and the
lower display will show [ p ; a C1] .
5. Press the Infinity Key to return Home. The Profile will Start
Ending a Profile from the Home Page
1. Press the Advance Key ‰ to select the Profile Action Request. The upper display will show [none] and
the lower display will show [ p ; a C1] .
2. Press the Up ¿ or Down ¯ keys to select the End. The upper display will show [~End ] and the lower
display will show [ p ; a C1]
3. Press the Infinity Key to return Home. The Profile will End.
Watlow EZ-ZONE ® PM PID Controller
•
28
•
Chapter 4 Home Page
Modifying the Home Page
Follow the steps below to modify the Home Page:
1. Push and hold the Advance ‰ key and the Infinity ˆ key for approximately six seconds. Upon entering the
Factory Page the first menu will be the Custom Menu [Cust] .
2. Push the Advance ‰ key where the lower display will show [Cust] and the upper display will show [1] .
3. Push the Advance ‰ button where the prompt for the Process Value [aC; p u] will be displayed on top and
Parameter [`par] in the bottom. There are twenty positions available that can be customized.
4. Pushing the Up ¿ or Down ¯ arrow keys will allow for a customized selection to be made (see list of
available parameters below).
Custom Menu Parameter Options
Description
Prompt *
All Models
None
Blank
Analog Input Value
[Ain1]
Cal In Offset
[i;Ca1]
Display Units
[C_F1]
Load Parameter Set
[Usr;1] [Usr;2]
Alarm Set Point Low
[a ; lo1] [a ; lo2]
[a ; lo3] [a ; lo4]
Alarm Set Point High
[a ; hi1] [a ; hi2]
[a ; hi3] [a ; hi4]
Hysteresis
[a ; hy1] [a ; hy2]
[a ; hy3] [a ; hy4]
Set Point
[C; s p1]
Active Process Value
[aC; p1]
Active Set Point
[aC; s1]
Manual Power
[o; s p1]
Autotune
[aut1]
Control Mode
[C; m1]
Heat Power
[ h; p r1]
Cool Power
[C; p r1]
Time Integral
[`ti1]
Time Derivative
[`td1]
Dead Band
[`d b1]
Heat Prop Band
[ h; p b1]
On/Off Heat Hysteresis
[ h; hy1]
Cool Prop Band
[C; p b1]
On/Off Cool Hysteresis
[C; hy1]
Ramp Rate
[r; rt1]
TRU-TUNE+ Enable
[ t; tu1]
Idle
[id ; s1]
If 4th digit of part number is B, E, R or N
Profile Start
[ p ; s t1]
Profile Action Request
[ p ; a C1]
Guaranteed Soak Deviation 1 [gsd1]
* The numerical digit shown in the prompts above (last digit), represents the parameter instance and can be
greater than one.
Watlow EZ-ZONE ® PM PID Controller
•
29
•
Chapter 4 Home Page
Modifying the Display Pairs
The Home Page, being a customized list of as many as 20 parameters can be configured in pairs of up to 10
via the Display Pairs [d;prs] prompt found in the Diagnostic Menu [diag] (Factory Page). The listing in the
table that follows is what one may typically find in the Home Page as defaults based on controller part numbers. It is important to note that some of the prompts shown may not appear simply because the feature is not
being used or is turned off. As an example, the prompt Cool Power [C; p r1] will not appear unless the Cool algorithm [`C; a g ] is turned on in the Setup Page under the Loop menu. The Display Pairs [d;prs] prompt will
default to 1, therefore the upper display will reflect the Active Process Value [aC;pu] and the lower display
will reflect the Active Set Point [aC;sp] by default.
As stated above, the user can define pairs of prompts to appear on the display every time the Advance
‰ key is pushed. When configuring the Custom Menu to your liking it should be noted that if 2 changeable
(writable) prompts are displayed in a pair, i.e., Control Mode on top and Idle Set Point on the bottom, only the
lower display (Idle Set Point) can be changed. If a writable value is placed on the upper display and is paired
with another read only parameter on the lower display, the arrow keys affect the setting of the upper display.
The display can be configured to scroll by going to the Factory Page under the Diagnostic Menu and
changing the Display Time [`d ; ti] prompt to something greater than 0. If set to 2, the display will scroll
every 2 seconds from one Display Pair to another. If the Display Pair prompt [d;prs] is set to 1 the Display
Time [`d ; ti] prompt will have no effect on the display.
Watlow EZ-ZONE ® PM PID Controller
•
30
•
Chapter 4 Home Page
Home Page Defaults
Home Page
Display
Parameter Page and Menu
All Models
1
Active Process Value (1)
Numerical
value
Operations Page, Monitor Menu
2
Active Set Point (1)
Numerical
value
Operations Page, Monitor Menu
3
Control Mode (1)
[C;M1]
Operations Page, Monitor Menu
4
Heat Power (1)
[h;pr1]
Operations Page, Monitor Menu
5
Cool Power (1)
[C;pr1]
Operations Page, Monitor Menu
6
Autotune (1)
[aut1]
Operations Page, Loop Menu
7
Idle Set Point (1)
[id;s1]
Operations Page, Loop Menu
8
* Profile Start
[p;st1]
9
* Action Request
[p;aC1]
10 None
11 None
12 None
13 None
14 None
15 None
16 None
17 None
18 None
19 None
20 None
* The fourth digit of the part number must be:
PM _ [R, B, N or E] _ _ _ - _ _ _ _ _ _ _
Note:
The numerical digit shown in the prompts (last digit) and within the parentheses above, represents the parameter instance and can be greater than one.
Watlow EZ-ZONE ® PM PID Controller
•
31
•
Chapter 4 Home Page
Navigating the EZ-ZONE® PM PID Controller
Applies to All Models - 1/16 DIN Shown Below
®
®
®
®
[``Ai]
[``70]
[``70]
[Cust]
[`Set]
[``72]
[``72]
[fCty]
Home Page from anywhere: Press the Infinity
Factory Page from Home Page: Press both the
Advance ‰ and Infinity ˆ keys for six seconds.
Key ˆ for two seconds to return to the Home Page.
®
®
[``70]
[``Ai]
[``72]
[oper]
Operations Page from Home Page: Press both
the Up ¿ and Down ¯ keys for three seconds.
®
®
[``70]
[``Ai]
[``72]
[`Set]
Note:
Keys must be held continuously until [`SEt]
is displayed in green. If keys are released when
[OPEr] is displayed, press the infinity key or
reset key to exit and repeat until [`SEt] is displayed.
Setup Page from Home Page: Press both the
Up ¿ and Down ¯ keys for six seconds.
®
®
[``70]
[``p1]
[``72]
[prof]
Profiling Page from Home Page: Press the
Advance Key ‰ for three seconds.
Watlow EZ-ZONE ® PM PID Controller
•
32
•
Chapter 4 Home Page
Conventions Used in the Menu Pages
To better understand the menu pages that follow review the naming conventions used. When encountered
throughout this document, the word "default" implies as shipped from the factory. Each page (Operations,
Setup, Profile and Factory) and their associated menus have identical headers defined below:
Header Name
Definition
Display
Visually displayed information from the control.
Parameter Name
Describes the function of the given parameter.
Range
Defines options available for this prompt, i.e., min/max values (numerical), yes/no, etc... (further explanation below).
Default
Values as delivered from the factory.
Modbus Relative Address
Identifies unique parameters using either the Modbus RTU or Modbus TCP protocols (further explanation below).
CIP (Common Industrial Protocol)
Identifies unique parameters using either the DeviceNet or EtherNet/IP protocol (further explanation below).
Profibus Index
Identifies unique parameters using Profibus DP protocol (further
explanation below).
Parameter ID
Identifies unique parameters used with other software such as, LabVIEW.
uint = Unsigned 16 bit integer
dint = long, 32-bit
string = ASCII (8 bits per character)
Data Type R/W
float =IEEE 754 32-bit
RWES= Readable
Writable
EEPROM (saved)
User Set (saved)
Display
Visual information from the control is displayed to the observer using a fairly standard 7 segment display.
Due to the use of this technology, several characters displayed need some interpretation, see the list below:
[1] = 1
[0] = 0
[i] = i
[r] = r
[2] = 2
[a] = A
[j] = J
[S] = S
[3] = 3
[b] = b
[H] = K
[t] = t
[4] = 4
[c], [C] = c
[l] = L
[U] = u
[5] = 5
[d] = d
[m] = M
[u] = v
[6] = 6
[e] = E
[n] = n
[w] = W
[7] = 7
[f] = F
[o] = o
[y] = y
[8] = 8
[g] = g
[p] = P
[2] = Z
[9] = 9
[h] = h
[q] = q
Watlow EZ-ZONE ® PM PID Controller
•
33
•
Chapter 4 Home Page
Range
Within this column notice that on occasion there will be numbers found within parenthesis. This number
represents the enumerated value for that particular selection. Range selections can be made simply by writing the enumerated value of choice using any of the available communications protocols. As an example, turn
to the Setup Page and look at the Analog Input [``Ai] menu and then the Sensor Type [`Sen] prompt. To
turn the sensor off simply write the value of 62 (off) to Modbus register 368 and send that value to the control.
Modbus RTU Protocols
All Modbus registers are 16-bits and as displayed in this manual are relative addresses (actual). Some legacy
software packages limit available Modbus registers to 40001 to 49999 (5 digits). Many applications today
require access to all available Modbus registers which range from 400001 to 465535 (6 digits). Watlow controls support 6 digit Modbus registers. For parameters listed as float notice that only one (low order) of the
two registers is listed, this is true throughout this document. By default the low order word contains the two
low bytes of the 32-bit parameter. As an example, look in the Operations Page for the Process Value. Find
the column identified in the header as Modbus and notice that it lists register 360. Because this parameter
is a float it is actually represented by registers 360 (low order bytes) and 361 (high order bytes). Because
the Modbus specification does not dictate which register should be high or low order Watlow provides the
user the ability to swap this order (Setup Page, [Com] Menu) from the default low/high [lohi] to high/low
[ hilo] .
Note:
With the release of firmware revision 7.00 and above new functions where introduced into this product line.
With the introduction of these new functions there was a reorganization of Modbus registers. Notice in the
column identified as Modbus the reference to Map 1 and Map 2 registers for each of the various parameters. If the new functions, namely; Linearization, Process Value and Real Time Clock are to be used than
use Map 2 Modbus regis
ters. The Data Map [map] for Modbus registers can be changed in the Setup
Page under the [Com] Menu. This setting will apply across the control.
It should also be noted that some of the cells in the Modbus column contain wording pertaining to an offset.
Several parameters in the control contain more than one instance; such as, profiles (4), alarms (4), analog inputs (2), etc... The Modbus register shown always represents instance one. Take for an example the Alarm Silence parameter found in the Setup Page under the Alarm menu. Instance one of Map 1 is shown as address
1490 and +50 is identified as the offset to the next instance. If there was a desire to read or write to instance
3 simply add 100 to 1490 to find its address, in this case, the instance 3 address for Alarm Silence is 1590.
To learn more about the Modbus protocol point your browser to http://www.modbus.org.
Note:
There are two columns shown in the menus that follow for communications protocols identified as CIP
(Common Industrial Protocol) and Profibus. These columns will be useful if this control is used in conjunction with the EZ-ZONE Remote User Interface/Gateway (RUI/GTW) where those protocols can be selected
as optional hardware. For this control, as a secondary protocol beyond Standard Bus, Modbus RTU can be
ordered as optional hardware.
To learn more about the RUI/GTW point your browser to the link below and search for keyword EZ-ZONE.
http://www.watlow.com/literature/pti_search.cfm
Watlow EZ-ZONE ® PM PID Controller
•
34
•
Chapter 4 Home Page
5
Chapter 5: Operations Page
Navigating the Operations Page
To navigate to the Operations Page, follow the steps below:
1.From the Home Page, press both the Up ¿ and Down ¯ keys for three seconds. [``Ai] will appear in the upper display and [oPEr] will appear in the lower display.
2.Press the Up ¿ or Down ¯ key to view available menus.
3.Press the Advance Key ‰ to enter the menu of choice.
4.If a submenu exists (more than one instance), press the Up ¿ or Down ¯ key to select and then press the Advance Key ‰ to enter.
5.Press the Up ¿ or Down ¯ key to move through available menu prompts.
6.Press the Infinity Key ˆ to move backwards through the levels: parameter to submenu; submenu to menu;
menu to Home Page.
7.Press and hold the Infinity Key ˆ for two seconds to return to the Home Page.
On the following pages, top level menus are identified with a yellow background color.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no submenus will appear.
Note:
Some of the listed parameters may not be visible. Parameter visibility is dependent upon controller part
number.
[``Ai]
[oPEr] Analog Input Menu
[`Ain] Analog Input Value
[`i;Er] Input Error
[`i;Ca] Calibration Offset
[`Lnr]
[oPEr] Linearization Menu
[`Su;A] Source Value A
[oFSt] Offset
[``o;u] Output Value
[``Pu]
[oPEr] Process Value Menu
[`Su;A] Source Value A
[oFSt] Offset
[``o;u] Output Value
[Loop]
[oPEr] Control Loop Menu
[`C;M] Control Mode
[A;tSP] Autotune Set Point
[`AUt] Autotune
[`C;SP] Set Point
[`id;S] Idle Set Point
[`h;Pb] Heat Proportional Band
[`h;hy] On/Off Heat Hysteresis
[`C;Pb] Cool Proportional Band
[`C;hy] On/Off Cool Hysteresis
[``ti] Time Integral
[``td] Time Derivative
[``db] Dead Band
[`o;SP] Manual Power
[ALM]
[`dio]
[oPEr] Digital Input/Output Menu
[```5]
[`dio] Digital Input/Output (5 to 6)
[`do;S] Output State
[`di;S] Input State
[`ei;S] Event State
[oPEr] Alarm Menu
[```1]
[ALM] Alarm 1 (1 to 4)
[`A;Lo] Low Set Point
[`A;hi] High Set Point
[a;Clr] Clear Alarm
[a;sir] Silence Alarm
[`a;st] Alarm State
[Mon]
[tMr]
[oPEr] Monitor Menu
[C;MA] Control Mode Active
[`h;Pr] Heat Power
[`C;Pr] Cool Power
[`C;SP] Set Point
[`Pu;A] Process Value Active
[tE;o2] Timer Event Output 2
[tE;o3] Timer Event Output 3
[``t;r] Time Remaining
[`r;bS] Ready Band State
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[Ct;SP] Closed Loop Timer Set
Point
P;StA]
[oPEr] Profile Status Menu [```1]
[P;StA] Profile Status (1 to 4)
[P;Str] Profile Start
[PACr] Profile Action Request
[`StP] Step
[S;tyP] Step Type
[t;SP1] Target Set Point Loop 1
[AC;SP] Produced Set Point 1
[hour] Hours
[min] Minutes
[`seC] Seconds
[Ent1] Event 1
[Ent2] Event 2
[``JC] Jump Count Remaining
[oPEr] Timer Menu
[`Su;A] Source Value A
[`Su;C] Source Value C
[`Su;d] Source Value D
[P;PS1] Produced Set Point 1
[tE;o1] Timer Event Output 1
Watlow EZ-ZONE ® PM PID Controller
•
35
•
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Instance 1
Map 1 Map 2
360
360
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
0x68 (104)
1
1
0
4001
float
R
[``Ai]
[oPEr]
Analog Input Menu
[`Ain]
[ Ain]
Analog Input (1)
Analog Input Value
View the process value.
Note:
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
----
Ensure that the Input
Error (below) indicates
no error (61) when reading this value using a
field bus protocol. If an
error exists, the last
known value prior to the
error occurring will be
returned.
[`i;Er]
[ i.Er]
Analog Input (1)
Input Error
View the cause of the most
recent error. If the [Attn]
message is [Er;i1] or
[Er;i2], this parameter
will display the cause of the
input error.
None
[nonE] None (61)
[OPEn] Open (65)
[FAiL] Fail (32)
[Shrt] Shorted (127)
[`E;M] Measurement
Error (140)
[E;CAL] Bad Calibration
Data (139)
[Er;Ab] Ambient Error (9)
[E;;Rtd] RTD Error (141)
[Nsrc] Not Sourced
(246)
Instance 1
Map 1 Map 2
362
362
0x68 (104)
1
2
1
4002
uint
R
[`i;Ca]
[ i.CA]
Analog Input (1)
Calibration Offset
Offset the input reading to
compensate for lead wire
resistance or other factors
that cause the input reading to vary from the actual
process value.
-1,999.000 to
9,999.000°F or units
-1,110.555 to
5,555.000°C
0.0
Instance 1
Map 1 Map 2
382
382
0x68 (104)
1
0xC (12)
2
4012
float
RWES
[`Lnr]
[oPEr]
Linearization Menu
[`Su;A]
[ Su.A]
Linearization (1)
Source Value A
View the value of Source
A.
Source A of Linearization
1 is connected to Analog
Input 1
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
----
Instance 1
Map 1 Map 2
- - - -
3566
0x86 (134)
1
4
----
34004
float
R
[oFSt]
[oFSt]
Linearization (1)
Offset
Set an offset to be applied
to this function's output.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0
Instance 1
Map 1 Map 2
- - - -
3570
0x86 (134)
1
6
----
34006
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
36
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
[``o;u]
[ o.v]
Linearization (1)
Output Value
View the value of this
function's output.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
No Display
Linearization (1)
Output Error
View reported cause for
Linearization output malfunction.
None (61)
Open (65)
Shorted (127)
Measurement error
(140)
Bad calibration data
(139)
Ambient error (9)
RTD error (14)
Fail (32)
Math error (1423)
Not sourced (246)
Stale (1617)
Can't process (1659)
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Instance 1
Map 1 Map 2
- - - -
3572
----
----
Default
----
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
0x86 (134)
1
7
----
34007
float
R
Instance 1
Map 1 Map 2
- - - -
3614
0x86 (134)
1
0x1C (28)
----
34028
uint
R
Instance 1
Map 1 Map 2
- - - -
3310
0x7E (126)
1
0x10 (16)
----
26016
float
R
Instance 1
Map 1 Map 2
- - - -
3324
0x7E (126)
1
0x17 (23)
----
26023
float
RWES
[``Pu]
[oPEr]
Process Value Menu
[`Su;A]
[ Sv.A]
Process Value (1)
-1,999.000 to
Source Value A
9,999.000°F or units
View the value of Source A. -1,128.000 to
Linearization 1 is connect5,537.000°C
ed to Source A of Process
Value 1
[oFSt]
[oFSt]
Process Value (1)
Offset
Set an offset to be applied
to this function's output.
[``o;u]
[ o.v]
Process Value (1)
-1,999.000 to
Output Value
9,999.000°F or units
View the value of this func- -1,128.000 to
tion block's output.
5,537.000°C
----
Instance 1
Map 1 Map 2
- - - -
3322
0x7E (126)
1
0x16 (22)
----
26022
float
R
No Display
Process Value (1)
Output Error
View reported cause for
Process output malfunction.
----
Instance 1
Map 1 Map 2
- - - -
3332
0x86 (134)
1 to 2
0x1B (27)
----
26027
uint
R
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0
[none] None (61)
[open] Open (65)
[shrt] Shorted (127)
[`e;m] Measurement
error (140)
[e;Cal] Bad calibration data (139)
[er;ab] Ambient error (9)
[e;rtd] RTD error (14)
[fail] Fail (32)
[e;rm] Math error
(1423)
[Nsrc] Not sourced
(246)
[stal] Stale (1617)
[no;pr] Can't process
(1659)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
37
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Parameter Name
Description
Display
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`dio]
[oPEr]
Digital Input/Output Menu
[`do;S]
[ do.S]
Digital Output (5 to 6)
Output State
View the state of this output.
[`off] Off (62)
[``on] On (63)
----
Instance 5
Map 1 Map 2
10121132
Offset to next
instance equals
+30
0x6A (106)
5 to 6
7
90
6007
uint
R
[`di;S]
[ di.S]
Digital Input (5 to 6)
[`off] Off (62)
Input State
[``on] On (63)
View this event input state.
----
Instance 5
Map 1 Map 2
10201140
Offset to next
instance equals
+30
0x6A (106)
5 to 6
0xB (11)
----
6011
uint
R
[`ei;S]
[ Ei.S]
Digital Input (5 to 6)
[`iact] Inactive (41)
Event Status
[``act] Active (5)
View this event input state.
----
Instance 5
Map 1 Map 2
13281568
Offset to next
instance equals
+20
0x6E (110)
5 to 6
5
140
10005
uint
R
No Display
EZ-Key/s (1 to 2)
[`iact] Inactive (41)
Event Status
[``act] Active (5)
View this event input state.
----
Instance 1
Map 1 Map 2
13681608
Instance 2
Map 1 Map 2
- - - - 1628
0x6E (110)
3 to 4
5
140
10005
uint
R
[Mon]
[oPEr]
Monitor Menu
[C;MA]
[C.MA]
Monitor (1)
Control Mode Active
View the current control
mode.
[`off] Off (62)
[AUto] Auto (10)
[MAn] Manual (54)
Off
Instance 1
Map 1 Map 2
18822362
0x97 (151)
1
2
----
8002
uint
R
[`h;Pr]
[ h.Pr]
Monitor (1)
Heat Power
View the current heat output level.
0.0 to 100.0%
0.0
Instance 1
Map 1 Map 2
19042384
0x97 (151)
1
0xD (13)
----
8011
float
R
[`C;Pr]
[ C.Pr]
Monitor (1)
Cool Power
View the current cool output level.
-100.0 to 0.0%
0.0
Instance 1
Map 1 Map 2
19062386
0x97 (151)
1
0xE (14)
----
8014
float
R
[`C;SP]
[ C.SP]
Monitor (1)
Set Point
View the set point currently in effect.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
----
Instance 1
Map 1 Map 2
21722652
0x6B (107)
1
7
----
8029
float
R
[`Pu;A]
[ Pv.A]
Monitor (1)
Process Value Active
View the current filtered
process value using the
control input.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
----
Instance 1
Map 1 Map 2
402402
0x68 (104)
1
0x16 (22)
----
8031
float
R
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
38
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
No Display
Monitor (1)
-1,999.000 to
Set Point Active
9,999.000°F or units
Read the current active set -1,128.000 to
point.
5,537.000°C
----
Instance 1
Map 1 Map 2
21722652
0x6B (107)
1
7
----
7018
float
R
No Display
Monitor (1)
Autotune Status
Read the present status of
Autotune.
----
Instance 1
Map 1 Map 2
19322412
0x97 (151)
1
0x1B (27)
----
8027
uint
R
[`off] Off (62)
[ts;1p] Waiting for
cross 1 positive (119)
[ts;1n] Waiting for
cross 1 negative (120)
[ts;2p] Waiting for
cross 2 positive (121)
[ts;2n] Waiting for
cross 2 negative (122)
[ts;3p] Waiting for
cross 3 positive (123)
[ts;3n] Waiting for
cross 3 negative (150)
[`mn] Measuring
maximum peak (151)
[`ma] Measuring
minimum peak (152)
[CalC] Calculating
(153)
[Cplt] Complete (18)
[``to] Timeout (118)
[Loop]
[oPEr]
Control Loop Menu
[`C;M]
[ C.M]
Control Loop (1)
Control Mode
Select the method that
this loop will use to control.
[`off] Off (62)
[AUto] Auto (10)
[MAn] Manual (54)
Auto
Instance 1
Map 1 Map 2
18802360
0x97 (151)
1
1
63
8001
uint
RWES
[A;tSP]
[A.tSP}
Control Loop (1)
Autotune Set Point
Set the set point that the
autotune will use, as a
percentage of the current
set point.
50.0 to 200.0%
90.0
Instance 1
Map 1 Map 2
19982398
0x97 (151)
1
0x14 (20)
----
8025
float
RWES
[`AUt]
[ AUt]
Control Loop (1)
Autotune
Start an autotune. While
the autotune is active, the
Home Page will display
[Attn] [tUn1]. When the
autotune is complete, the
message will clear automatically.
[``no] No (59)
[`YES] Yes (106)
No
Instance 1
Map 1 Map 2
19202400
0x97 (151)
1
0x15 (21)
64
8026
uint
RW
[`C;SP]
[ C.SP]
Control Loop (1)
Set Point
Set the set point that the
controller will automatically control to.
Minimum Set Point to
Maximum Set Point
(Setup Page)
75.0°F
or
units
24.0°C
Instance 1
Map 1 Map 2
21602640
0x6B (107)
1
1
49
7001
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
39
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`id;S]
[ id.S]
Control Loop (1)
Idle Set Point
Set a Set Point that can
be triggered by an event
state.
Minimum Set Point to
Maximum Set Point
(Setup Page)
75.0°F
or
units
24.0°C
Instance 1
Map 1 Map 2
21762656
0x6B (107)
1
9
50
7009
float
RWES
[`h;Pb]
[ h.Pb]
Control Loop (1)
Heat Proportional Band
Set the PID proportional
band for the heat outputs.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
25.0°F
or
units
14.0°C
Instance 1
Map 1 Map 2
18902370
0x97 (151)
1
6
65
8009
float
RWES
[`h;hy]
[ h.hy]
Control Loop (1)
On/Off Heat Hysteresis
Set the control switching
hysteresis for on-off control. This determines how
far into the “on” region
the process value needs
to move before the output
turns on.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
3.0°F or
units
2.0°C
Instance 1
Map 1 Map 2
19002380
0x97 (151)
1
0xB (11)
66
8010
float
RWES
[`C;Pb]
[ C.Pb]
Control Loop (1)
Cool Proportional Band
Set the PID proportional
band for the cool outputs.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
25.0°F
or
units
14.0°C
Instance 1
Map 1 Map 2
18922372
0x97 (151)
1
7
67
8012
float
RWES
[`C;hy]
[ C.hy]
Control Loop (1)
On/Off Cool Hysteresis
Set the control switching
hysteresis for on-off control. This determines how
far into the “on” region
the process value needs
to move before the output
turns on.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
3.0°F or
units
2.0°C
Instance 1
Map 1 Map 2
19022382
0x97 (151)
1
0xC (12)
68
8013
float
RWES
[``ti]
[ ti]
Control Loop (1)
Time Integral
Set the PID integral for
the outputs.
0 to 9,999 seconds per
repeat
180 seconds
per
repeat
Instance 1
Map 1 Map 2
18942374
0x97 (151)
1
8
69
8006
float
RWES
[``td]
[ td]
Control Loop (1)
Time Derivative
Set the PID derivative
time for the outputs.
0 to 9,999 seconds
0
Instance 1
seconds Map 1 Map 2
18962376
0x97 (151)
1
9
70
8007
float
RWES
[``dB]
[ db]
Control Loop (1)
Dead Band
Set the offset to the
proportional band. With
a negative value, both
heating and cooling outputs are active when the
process value is near the
set point. A positive value
keeps heating and cooling
outputs from fighting each
other.
-1,000.0 to 1,000.0°F
or units
-556 to 556°C
0
Instance 1
Map 1 Map 2
18982378
0x97 (151)
1
0xA (10)
71
8008
float
RWES
[`o;SP]
[ o.SP]
Control Loop (1)
Manual Power
Set a fixed level of output
power when in manual
(open-loop) mode.
-100 to 100% (heat and
cool)
0 to 100% (heat only)
-100 to 0% (cool only)
0.0
Instance 1
Map 1 Map 2
21622642
0x6B (107)
1
2
51
7002
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
40
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Parameter Name
Description
Display
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
No Display
Control Loop (1)
Loop Error
Open Loop detect deviation has been exceeded.
[none] None (61)
[`lp;o] Open Loop
(1274)
[`lp;r] Reversed Sensor (1275)
----
Instance 1
Map 1 Map 2
- - - -
2408
0x6C (108)
1
0x30 (48)
----
8030
uint
R
No Display
Control Loop (1)
Clear Loop Error
Current state of limit
output.
[`Clr] Clear (129)
[ignr] Ignore (204)
----
Instance 1
Map 1 Map 2
- - - -
2410
0x6C (108)
1
0x31 (49)
----
8031
uint
W
No Display
Control Loop (1)
Loop Output Power
View the loop output
power.
-100.0 to 100.0
----
Instance 1
Map 1 Map 2
19082388
0x97 (151)
1
0x0F (15)
----
8033
float
R
Alarm (1 to 4)
Low Set Point
If Type (Setup Page,
Alarm Menu) is set to:
process - set the process
value that will trigger a
low alarm.
deviation - set the span
of units from the Set
Point that will trigger a
low alarm. A negative set
point represents a value
below Set Point. A positive set point represents
a value above Set Point.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
32.0°F
or
units
0.0°C
Instance 1
Map 1 Map 2
14821882
0x6D
(109)
1 to 4
2
18
9002
float
RWES
Alarm (1 to 4)
High Set Point
If Type (Setup Page,
Alarm Menu) is set to:
process - set the process
value that will trigger a
high alarm.
deviation - set the span of
units from the Set Point
that will trigger a high
alarm.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0x6D
(109)
1 to 4
1
19
9001
float
RWES
Alarm (1 to 4)
Alarm State
Current state of alarm
[`Str] Startup (88)
[nonE] None (61)
[`bLo] Blocked (12)
[`AL;l] Alarm low (8)
[`AL;h] Alarm high (7)
[`Err] Error (28)
0x6D
(109)
1 to 4
9
----
9009
uint
R
[ALM]
[oPEr]
Alarm Menu
[`A;Lo]
[ A.Lo]
[`A;hi]
[ A.hi]
No Display
Offset to next
instance (Map
1) equals +50
Offset to next
instance (Map
2) equals +60
300.0°F
or
units
150.0°C
Instance 1
Map 1 Map 2
14801880
Offset to next
instance (Map
1) equals +50
Offset to next
instance (Map
2) equals +60
Instance 1
Map 1 Map 2
14961896
None
Offset to next
instance [Map1
+50], [Map 2
+60]
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
41
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Parameter Name
Description
Display
No Display
Alarm (1 to 4)
Alarm Clearable
Indicates if the alarm can
be cleared.
Range
Default
----
[``no] No (59)
[`YES] Yes (106)
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Instance 1
Map 1 Map 2
15021902
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
0x6D
(109)
1 to 4
0xC (12)
----
9012
uint
R
0x6D
(109)
1 to 4
0xD (13)
----
9013
uint
W
0x6D
(109)
1 to 4
0xE (14)
----
9014
uint
W
0x6D
(109)
1 to 4
0x0B (11)
----
9011
uint
R
0x6D
(109)
1 to 4
0x0A (10)
----
9010
uint
R
0x83 (109)
1
0x07 (7)
----
31007
uint
R
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
No Display
Alarm (1 to 4)
Clear Alarm
Write to this register to
clear an alarm
Instance 1
Map 1 Map 2
15041904
0
[`Clr] Clear (0)
[ignr] Ignore (204)
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
No Display
Alarm (1 to 4)
Silence Alarm
Write to this register to
silence an alarm
Instance 1
Map 1 Map 2
15061906
0
[`sil] Silence Alarm
(1010)
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
No Display
Alarm (1 to 4)
Alarm Silenced
Indicates if alarm is silenced.
----
[``no] No (59)
[`YES] Yes (106)
Instance 1
Map 1 Map 2
15001900
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
No Display
Alarm (1 to 4)
Alarm Latched
Indicates if alarm is
latched.
----
[``no] No (59)
[`YES] Yes (106)
Instance 1
Map 1 Map 2
14981898
Offset to next
instance (Map1
1 equals +50,
Map 2 equals
+60)
[tMr]
[oPEr]
Timer Menu
[`Su;A]
[ Su.A]
Timer
Source Value A
View the state of Source
Function A.
----
[``on] On (63)
[`oFF] Off (62)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
42
•
Instance 1
Map 1 Map 2
- - - -8012
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`Su;C]
[ Su.C]
Timer
Source Value C
View the value of Source
Function C.
-1999.000 to 999.000°F
or units
-1110.555 to 5555.000
----
Instance 1
Map 1 Map 2
- - - -8572
0x83 (109)
1
0x25 (37)
----
31037
float
R
[`Su;d]
[ Su.d]
Timer
Source Value D
View the state of Source
Function D.
[``on] On (63)
[`oFF] Off (62)
----
Instance 1
Map 1 Map 2
- - - -8574
0x83 (109)
1
0x26 (38)
----
31038
uint
R
[P;SP1]
[P.SP1]
Timer
Produced Set Point 1
View the value of Set
Point 1.
-1999.000 to 999.000°F
or units
-1110.555 to 5555.000
----
Instance 1
Map 1 Map 2
- - - -8576
0x83 (109)
1
0x27 (39)
----
31039
float
R
[tE;o1]
[tE.o1]
Timer
Timer Event Output 1
View the state of Event
Output 1.
[``on] On (63)
[`oFF] Off (62)
----
Instance 1
Map 1 Map 2
- - - -8578
0x83 (109)
1
0x28 (40)
----
31040
uint
R
[tE;o2]
[tE.o2]
Timer
Timer Event Output 2
View the state of Event
Output 2.
[``on] On (63)
[`oFF] Off (62)
----
Instance 1
Map 1 Map 2
- - - -8580
0x83 (109)
1
0x29 (41)
----
31041
uint
R
[tE;o3]
[tE.o3]
Timer
Timer Event Output 3
View the state of Event
Output 3.
[``on] On (63)
[`oFF] Off (62)
----
Instance 1
Map 1 Map 2
- - - -8590
0x83 (109)
1
0x2E (46)
----
31046
uint
R
[``t;r]
[ t.r]
Timer
[00;00] 00:00 to 99:59
Time Remaining
Display the time remaining
on the timer.
Instance 1
Map 1 Map 2
- - - -
0x83 (131)
1
0x15 (21)
----
31021
string
R
[`r;bS]
[ r.bS]
Timer
Ready Band State
Display whether the process value is in the ready
band.
Instance 1
Map 1 Map 2
- - - -8542
0x83 (131)
1
0x16 (22)
----
31022
uint
R
[hoUr]
[hoUr]
Timer
0 to 99
Hours
Set the timer period hours.
0
Instance 1
Map 1 Map 2
- - - -8548
0x83 (131)
1
0x19 (25)
----
31025
uint
RWES
[Min]
[Min]
Timer
Minutes
Set the timer period minutes.
0 to 59
0
Instance 1
Map 1 Map 2
- - - -8550
0x83 (131)
1
0x1A (26)
----
31026
uint
RWES
[`SEC]
[ SEC]
Timer
Seconds
Set the timer period seconds.
0 to 59
10
Instance 1
Map 1 Map 2
- - - -8552
0x83 (131)
1
0x1B (27)
----
31027
uint
RWES
[Ct;SP]
[Ct.SP]
Timer
Closed Loop Timer Set
Point
Set the set point that will
be in effect during the
timer period.
-1999.000 to 9999.000°F 75
or units
-1110.555 to 5555.000°C
Instance 1
Map 1 Map 2
- - - -8554
0x83 (131)
1
0x1C (28)
----
31028
float
RWES
7
----
[`YES] Yes (106)
[``no] No (59)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
43
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
No Display
Timer
Timer Timing
Indicates whether the
timer is running.
On (63)
Off (62)
----
Instance 1
Map 1 Map 2
- - - -8528
0x83 (131)
1
0x0F (15)
----
31015
uint
R
No Display
Timer
Output Error
Indicates errors that may
have interfered with the
timer operation.
None (61)
Open (65)
Shorted (127)
Measurement Error
(140)
Bad Calibration Data
(139)
Ambient Error (9)
RTD Error (141)
Fail (32)
Math Error (1423)
Not Sourced (246
Stale (1617)
----
Instance 1
Map 1 Map 2
- - - -8534
0x83 (131)
1
0x12 (18)
----
31018
uint
R
No Display
Timer
Indicator Request
View the status of the timer illuminated indicators.
Off (62)
Ready (1662)
Ready Ack (1950)
Running (149)
----
Instance 1
Map 1 Map 2
- - - -8582
0x83 (131)
1
0x2A (42)
----
31042
uint
R
No Display
Timer
Inactive (41)
Countdown State
Wait Process (209)
View the state of the count- Wait Event (144)
down cycle.
Running (149)
Pause (146)
Complete (18)
End (27)
----
Instance 1
Map 1 Map 2
- - - -8584
0x83 (131)
1
0x2B (43)
----
31043
uint
R
No Display
Timer
Elapsed Signal Time
Counts from 0 to Signal
Time while signal time is
active.
0 to 4,294,967,295 mS
----
Instance 1
Map 1 Map 2
- - - -8592
0x83 (131)
1
0x2F (47)
----
31047
udint
R
No Display
Timer
0 to 4,294,967,295 mS
Elapsed Time
Counts from 0 to Countdown Time while time cycle
is active.
----
Instance 1
Map 1 Map 2
- - - -8594
0x83 (131)
1
0x30 (48)
----
31048
udint
R
* Available with PM8/9 only
*Some parameters in the Profile Status Menu can be changed for the
currently running profile, but should only be changed by knowledgeable personnel and with caution. Changing parameters via the Profile Status Menu will not change the stored profile but will have an
immediate impact on the profile that is running.
Changes made to profile parameters in the Profiling Pages will be
saved and will also have an immediate impact on the running profile.
[P;Sta]
[oPEr]
Profile Status Menu
Profile Menu appears if:
(PM _ [R, B*, N, E*] _ _ _-_ _ _ _ _ _ _)
[P;Str]
[P.Str]
Profile Status
Profile Start
Select step to act upon.
1 to 40
Instance 1
Map 1 Map 2
25204340
1
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
44
•
0x7A (122)
1
1
204
22001
uint
RW
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[P;ACr]
[PACr]
Profile Status
Action Request
[nonE] None (61)
[step] Step Start (89)
[`End] Terminate
(148)
[rESU] Resume (147)
[PAUS] Pause (146)
[ProF] Profile (77)
None
Instance 1
Map 1 Map 2
25404360
0x7A (122)
1
0xB (11)
205
22011
uint
RW
[`StP]
[ StP]
Profile Status
Step
View the currently running step.
1 to 40
0 (none)
Instance 1
Map 1 Map 2
25264346
0x7A (122)
1
4
----
22004
uint
R
[S;typ]
[S.typ]
Profile Status
Step Type
View the currently running step type.
UStP] Unused Step
(50)
[`End] End (27)
[``JL] Jump (116)
[CloC] Wait For Time
(1543)
[W;bo] Wait For Both
(210)
[W;Pr] Wait For Process (209)
[`W;E] Wait For Event
(144)
[SoAH] Soak (87)
[``ti] Ramp Time
(143)
[rAtE] Ramp Rate (81)
----
Instance 1
Map 1 Map 2
25444364
0x7A (122)
1
0xD (13)
----
22013
uint
R
[t;SP1]
[t.SP1]
Profile Status
-1,999.000 to
*Target Set Point Loop 1
9,999.000°F or units
View or change the target -1,128.000 to
set point of the current
5,537.000°C
step.
0.0°F
or
units
-18.0°C
Instance 1
Map 1 Map 2
25424502
0x7A (122)
1
0xC (12)
----
22012
uint
RW
[aC;sp]
[AC.SP]
Profile Status
Produced Set Point 1
Display the current set
point, even if the profile is
ramping.
-1,999.000 to
9,999.000°F or units
-1,128.000 to
5,537.000°C
0.0°F
or
units
-18.0°C
Instance 1
Map 1 Map 2
25284348
----
----
22005
float
R
[hoUr]
[hoUr]
Profile Status
Hours
Step time remaing in
hours.
0 to 99
0
Instance 1
Map 1 Map 2
- - - -
4494
0x7A (122)
1
0x4E (78)
----
22078
uint
RW
[min]
Profile Status
Minutes
Step time remaing in
minutes.
0 to 59
0
Instance 1
Map 1 Map 2
- - - -
4492
0x7A (122)
1
0x4D (77)
----
22077
uint
RW
[`seC]
[ SEC]
Profile Status
Seconds
Step time remaing in
seconds.
0 to 59
0
Instance 1
Map 1 Map 2
- - - -
4490
0x7A (122)
1
0x4C (76)
----
22076
uint
RW
[Ent1]
[Ent1]
Profile Status
Event 1
View or change the event
output states.
[`off] Off (62)
[``on] On (63)
Off
Instance 1
Map 1 Map 2
25464512
0x7A (122)
1
0xE (14)
----
22014
uint
RW
[Min]
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
45
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
Operations Page
Display
Parameter Name
Description
Range
Default
Modbus Relative Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[Ent2]
[Ent2]
Profile Status
Event 2
View or change the event
output states.
[`off] Off (62)
[``on] On (63)
Off
Instance 1
Map 1 Map 2
2548
4514
0x7A (122)
1
0xF (15)
----
22015
uint
RW
[``JC]
[ JC]
Profile Status
Jump Count Remaining
View the jump counts
remaining for the current
loop. In a profile with
nested loops, this may not
indicate the actual jump
counts remaining.
0 to 9,999
0
Instance 1
Map 1 Map 2
25384358
0x7A (122)
1
0xA (10)
----
22010
uint
R
No Display
Profile Status
Profile State
Read currentProfile state.
off (62)
Running (149)
Pause (146)
Instance 1
Map 1 Map 2
25224342
0x7A (122)
1
2
----
22002
uint
R
No Display
Profile Status
Current File
Indicates current file being executed.
Instance 1
Map 1 Map 2
25244344
0x7A (122)
1
3
----
22003
uint
R
----
1 to 4
0
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
46
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 5 Operations Page
6
Chapter 6: Setup Page
Navigating the Setup Page
To go to the Setup Page from the Home Page, press both the Up ¿ and Down ¯ keys for six seconds. [``Ai]
will appear in the upper display and [`Set] will appear in the lower display.
• Press the Up ¿ or Down ¯ key to view available menus. On the following pages top level menus are identified with a yellow background color.
•Press the Advance Key ‰ to enter the menu of choice.
• If a submenu exists (more than one instance), press the Up ¿ or Down ¯ key to select and then press the
Advance Key ‰ to enter.
• Press the Up ¿ or Down ¯ key to move through available menu prompts.
• Press the Infinity Key ˆ to move backwards through the levels: parameter to submenu; submenu to menu;
menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds to return to the Home Page.
Note:
Keys must be held continuously until [`SEt] is displayed in green. If keys are released when [OPEr] is
displayed, press the infinity key or reset key to exit and repeat until [`SEt] is displayed, if you are using
firmware 13 or earlier.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information.
[``Ai]
[`Set] Analog Input Menu
[`SEn] Sensor Type
[`Lin] TC Linearization
[`rt;L] RTD Leads
[Unit] Units
[`S;Lo] Scale Low
[`S;hi] Scale High
[`r;Lo] Range Low
[`r;hi] Range High
[`P;EE] Process Error Enable
[`P;EL] Process Error Low Value
[``t;C] Thermistor Curve
[``r;r] Resistance Range
[`FiL] Filter
[`i;er] Error Latching
[`dEC] Display Precision
[`i;Ca] Calibration Offset **
[`Ain] Analog Input Value **
[`i;Er] Input Error **
[`Lnr]
[`Set] Linearization Menu
[``Fn] Function
[Unit] Units
[`ip;1] Input Point 1
[`op;1] Output Point 1
[`ip;2] Input Point 2
[`op;2] Output Point 2
[`ip;3] Input Point 3
[`op;3] Output Point 3
[`ip;4] Input Point 4
[`op;4] Output Point 4
[`ip;5] Input Point 5
[`op;5] Output Point 5
[`ip;6] Input Point 6
[`op;6]
[`ip;7]
[`op;7]
[`ip;8]
[`op;8]
[`ip;9]
[`op;9]
[ip;10]
[op;10]
Output Point 6
Input Point 7
Output Point 7
Input Point 8
Output Point 8
Input Point 9
Output Point 9
Input Point 10
Output Point 10
[``Pu]
[`Set] Process Value
[``Fn] Function
[P;unt] Pressure Units
[A;unt] Altitude Units
[[`FiL] Filter
[`dio]
[`Set] Digital Input/Output Menu
[```5]
[`dio] Digital Input/Output (5 to 6)
[`dir] Direction
[``Fn] Output Function
[``Fi] Output Function Instance
[`o;Ct] Time Base Type
[`o;tb] Fixed Time Base
[`o;Lo] Low Power Scale
[`o;hi] High Power Scale
[`LEu] Active Level
[``fn] Active Level Function
[``fi] Function Instance
[Loop]
[`Set] Control Loop Menu
[`h;Ag] Heat Algorithm
[`C;Ag] Cool Algorithm
[`C;Cr] Cool Output Curve
[`h;Pb] Heat Proportional Band **
[`h;hy] On/Off Heat Hysteresis **
[`C;Pb] Cool Proportional Band **
[`C;hy] On/Off Cool Hysteresis **
[``ti] Time Integral **
[``td] Time Derivative **
[``db] Dead Band **
[t;tUn] TRU-TUNE+™ Enable
[t;bnd] TRU-TUNE+™ Band
[`t;gn] TRU-TUNE+™ Gain
[A;tSP] Autotune Set Point
[t;Agr] Autotune Aggressiveness
[`P;dl] Peltier Delay
[`UFA] Auto-to-Manual Power
[FAiL] Input Error Power
[MAn] Fixed Power
[`L;dE] Open Loop Detect Enable
[`L;dt] Open Loop Detect Time
[`L;dd] Open Loop Detect Deviation
[``rp] Ramp Action
[`r;SC] Ramp Scale
[`r;rt] Ramp Rate
[`L;SP] Minimum Set Point
[`h;SP] Maximum Set Point
[`C;SP] Set Point **
[`id;S] Idle Set Point **
[SP;Lo] Minimum Manual Power
[SP;hi] Maximum Manual Power
[`o;SP] Manual Power **
[`C;M] Control Mode **
** These parameters/prompts are available with firmware revisions 11.0 and above.
Watlow EZ-ZONE ® PM PID Controller
•
47
•
Chapter 6 Setup Page
[`r;bS] Ready Band State
[`rdY] Ready Band
[t;For] Time Format
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[Ct;SP] Closed Loop Timer Set Point
[``St] Signal Time
[otpt]
[`Set] Output Menu
[```1]
[otpt] Output (1 to 2)
[``Fn] Function
[``Fi] Output Function Instance
[`o;Ct] Time Base Type
[`o;tb] Fixed Time Base
[`o;Lo] Low Power Scale
[`o;hi] High Power Scale
[otpt] Output 1 process
[`o;ty] Output Type
[``Fn] Function
[``Fi] Output Function Instance
[`S;Lo] Scale Low
[`S;hi] Scale High
[`r;Lo] Range Low
[`r;hi] Range High
[`o;lo] Low Power Scale
[`o;ho] High Power Scale
[`o;CA] Calibration Offset
[`fUn]
[`Set] Function Key Menu
[```1]
[`fUn] Function Key (1 to 2)
[`leu] Level
[``Fn] Action Function
[``fi] Function Instance
[gLbL]
[`Set] Global Menu
[`C_F] Display Units
[AC;LF] AC Line Frequency
[r;typ] Ramping Type
[p;typ] Profile Type
[`gse] Guaranteed Soak Enable
[gsd1] Guaranteed Soak Deviation 1
[`si;a] Source Instance A
[`si;b] Source Instance B
[poti] Power Off Time
[subt]Synchronized Variable Time Base
[C;led] Communications LED Action
[2one] Zone
[Chan] Channel
[d;prs] Display Pairs
[`d;ti] Display Time
[Usr;s] Restore Settings From
[Usr;r] Save Settings As
[ALM]
[`Set] Alarm Menu
[```1]
[ALM] Alarm (1 to 4)
[`A;ty] Type
[`sr;a] Alarm Source
[`A;hy] Hysteresis
[`a;Lg] Logic
[`A;SD] Sides
[`A;Lo] Low Set Point **
[`A;hi] High Set Point **
[`a;LA] Latching
[`A;bL] Blocking
[`a;Si] Silencing
[A;dsp] Alarm Display
[`A;dL] Delay Time
[a;Clr] Clear Alarm
[a;sir] Silence Alarm
[`a;st] Alarm State
[COM]
[`Set] Communications Menu
[pCol] Protocol
[`a;ds] Standard Bus Address
[ad;m] Modbus Address
[bAUd] Baud Rate
[`PAr] Parity
[M;hL] Modbus Word Order
[`C_f] Display Units
[map] Data Map
[`nu;s] Non-Volatile Save
[tMr]
[`Set] Timer Menu
[ti;En] Timer Enable
[ti;St] Timer Start Method
[SFn;A] Source Function A
[`Si;A] Source Instance A
[SFn;C] Source Function C
[`Si;C] Source Instance C
[SFn;d] Source Function D
[`Si;d] Source Instance D
[``t;r] Time Remaining
[`rtC]*
[`Set] Real Time Clock Menu
[hoUr] Hours
[min] Minutes
[dow] Day of Week
* Available with PM4, PM8 and PM9 models only
** These parameters/prompts are available with firmware revisions 11.0 and above.
Watlow EZ-ZONE ® PM PID Controller
•
48
•
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
Instance 1
0x68 (104)
1
Map 1 Map 2
5
368368
3
4005
uint
RWES
[```b] B (11) [```H] K (48) J
[```C] C (15) [```n] N (58)
[```d] D (23) [```r] R (80)
[```E] E (26) [```S] S (84)
[```F] F (30) [```t] T (93)
[```J] J (46)
Instance 1
0x68 (104)
1
Map 1 Map 2
6
370370
4
4006
uint
RWES
2
Instance 1
0x68 (104)
1
Map 1 Map 2
7
372372
----
4007
uint
RWES
Instance 1
0x68 (104)
1
Map 1 Map 2
----
442 0x2A (42)
5
4042
uint
RWES
0.0
Instance 1
0x68 (104)
1
Map 1 Map 2
0xF (15)
388 388
6
4015
float
RWES
20.0
Instance 1
0x68 (104)
1
Map 1 Map 2
0x10 (16)
390 390
7
4016
float
RWES
0.0
Instance 1
0x68 (104)
1
Map 1 Map 2
0x11 (17)
392 392
8
4017
float
RWES
Range
Default
[``Ai]
[`Set]
Analog Input Menu
[`Sen]
[ SEn]
Analog Input (1)
[`oFF] Off (62)
Sensor Type
[``tC] Thermocouple (95)
Set the analog sensor type [`mu] Millivolts (56)
to match the device wired
[uolT] Volts dc (104)
to this input.
[`MA] Milliamps dc
(112)
Note:
There is no open-sensor de- [r0;1H] RTD 100 Ω (113)
tection for process inputs.
[r1;0H] RTD 1,000 Ω (114)
[`Pot] Potentiometer 1
kΩ (155)
[thEr] Thermistor (229)
[`Lin]
[ Lin]
Analog Input (1)
TC Linearization
Set the linearization to
match the thermocouple
wired to this input.
[`Rt;L]
[ rt.L]
Analog Input (1)
[```2] 2 (1)
RTD Leads
[```3] 3 (2)
Set to match the number
of leads on the RTD wired
to this input.
[Unit]
[Unit]
Analog Input (1)
Units
Set the type of units the
sensor will measure.
[`S;Lo]
[ S.Lo]
Analog Input (1)
Scale Low
Set the low scale for process inputs. This value,
in millivolts, volts or milliamps, will correspond to
the Range Low output of
this function block.
[`S;hi]
[ S.hi]
Analog Input (1)
-100.0 to 1,000.0
Scale High
Set the high scale for
process inputs. This value,
in millivolts, volts or milliamps, will correspond to
the Range High output of
this function block.
[`r;Lo]
[ r.Lo]
Analog Input (1)
Range Low
Set the low range for this
function block's output.
----
[`A;tP] Absolute Tempera- Process
ture (1540)
[``rh] Relative Humidity
(1538)
[`Pro] Process (75)
[PWr] Power (73)
-100.0 to 1,000.0
-1,999.000 to 9,999.000
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
49
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`r;hi]
[ r.hi]
Analog Input (1)
-1,999.000 to 9,999.000
Range High
Set the high range for this
function block's output.
9,999
Instance 1
0x68 (104)
1
Map 1 Map 2
0x12 (18)
394 394
9
4018
float
RWES
[`P;EE]
[ P.EE]
Analog Input (1)
Process Error Enable
Turn the Process Error
Low feature on or off.
[`off] Off (62)
[Low] Low (53)
Off
Instance 1
0x68 (104)
1
Map 1 Map 2
418 418 0x1E (30)
10
4030
uint
RWES
[`P;EL]
[ P.EL]
Analog Input (1)
Process Error Low
Value
If the process value drops
below this value, it will
trigger an input error.
-100.0 to 1,000.0
0.0
Instance 1
0x68 (104)
1
Map 1 Map 2
420 420 0x1F (31)
11
4031
float
RWES
[``t;C]
[ t.C]
Analog Input (1)
Thermistor Curve
Select a curve to apply to
the thermistor input.
[```A]
[```b]
[```C]
[CUSt]
Curve A (1451)
Curve B (1452)
Curve C (1453)
Custom (180)
Curve A
Instance 1
0x68 (104)
1
Map 1 Map 2
0x26 (38)
434 434
----
4038
uint
RWES
[``r;r]
[ r.r]
Analog Input (1)
Resistance Range
Set the maximum resistance of the thermistor
input.
[```5]
[``10]
[``20]
[``40]
5K (1448)
10K (1360)
20K (1361)
40K (1449)
40K
Instance 1
0x68 (104)
1
Map 1 Map 2
0x25 (37)
432 432
----
4037
uint
RWES
[`FiL]
[ FiL]
Analog Input (1)
0.0 to 60.0 seconds
Filter
Filtering smooths out the
process signal to both the
display and the input.
Increase the time to increase filtering.
0.5
Instance 1
0x68 (104)
1
Map 1 Map 2
0xE (14)
386386
12
4014
float
RWES
[`i;Er]
[ i.Er]
Analog Input (1)
[`off] Off (62)
Input Error Latching
[``on] On (63)
Turn input error latching
on or off. If latching is on,
errors must be manually
cleared.
Off
Instance 1
0x68 (104)
1
Map 1 Map 2
414 414 0x1C (28)
----
4028
uint
RWES
[`dEC]
[ dEC]
Analog Input (1)
Display Precision
Set the precision of the
displayed value.
[```0] Whole (105)
[``0;0] Tenths (94)
[`0;00] Hundredths (40)
[0;000] Thousandths (96)
Whole
Instance 1
0x68 (104)
Map 1 Map 2
1
398 398
0x14 (20)
----
4020
uint
RWES
[`i;Ca]
[ i.CA]
Analog Input (1)
Calibration Offset
Offset the input reading
to compensate for lead
wire resistance or other
factors that cause the input reading to vary from
the actual process value.
-1,999.000 to 9,999.000°F
or units
-1,110.555 to 5,555.000°C
0.0
Instance 1
0x68 (104)
Map 1 Map 2
1
382 382 0x0C (12)
2
4012
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
50
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`Ain]
[ Ain]
Parameter Name
Description
Analog Input (1)
Analog Input Value
View the process value.
Note:
Range
Default
-1,999.000 to 9,999.000°F
or units
-1,128.000 to 5,537.000°C
----
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
Instance 1
0x68 (104)
Map 1 Map 2
1
360 360
1
0
4001
float
R
Instance 1
0x68 (104)
Map 1 Map 2
1
362 362
2
1
4002
float
R
Instance 1
0x86 (134)
1
Map 1 Map 2
5
- - - -
3568
155
34005
uint
RWES
Ensure that the Input
Error Status (below)
indicates no error (61)
when reading this value
using a field bus protocol. If an error exists,
the last known value
prior to the error occurring will be returned.
[`i;Er]
[ i.Er]
Analog Input (1)
Input Error Status
View the cause of the
most recent error. If
the [Attn] message is
[Er;i1] or [Er;i2], this
parameter will display the
cause of the input error.
None
[nonE] None (61)
[OPEn] Open (65)
[Shrt] Shorted (127)
[`E;M] Measurement Error (140)
[E;CAL] Bad Calibration
Data (139)
[Er;Ab] Ambient Error (9)
[E;;Rtd] RTD Error (141)
[FAiL] Fail (32)
[Nsrc] Not Sourced (246)
[`Lnr]
[`Set]
Linearization Menu
[``Fn]
[ Fn]
Linearization (1)
Off
[`oFF] Off (62)
Function
[intr] Interpolated (1482)
Set how this function will
linearize Source A which
is Analog Input 1.
[Unit]
[Unit]
Linearization (1)
Units
Set the units of Source A
which is Analog Input 1.
Source
[nonE] None (61)
[`Src] Source (1539)
[``rh] Relative Humidty
(1538)
[`pro] Process (75)
[PWr] Power (73)
[`r;tp] Relative Temperature (1541)
[`A;tP] Absolute Temperature (1540)
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3616 0x29 (41)
156
34029
uint
RWES
[`iP;1]
[ ip.1]
Linearization (1)
Input Point 1
Set the value that will be
mapped to output 1.
-1,999.000 to 9,999.000
0.0
Instance 1
0x86 (134)
1
Map 1 Map 2
8
- - - -
3574
157
34008
float
RWES
[`oP;1]
[ op.1]
Linearization (1)
Output Point 1
Set the value that will be
mapped to input 1.
-1,999.000 to 9,999.000
0.0
Instance 1
0x86 (134)
1
Map 1 Map 2
- - - -
3594 0x12 (18)
158
34018
float
RWES
[`iP;2]
[ ip.2]
Linearization (1)
Input Point 2
Set the value that will be
mapped to output 2.
-1,999.000 to 9,999.000
1.0
Instance 1
0x86 (134)
1
Map 1 Map 2
9
----
3576
159
34009
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
51
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`oP;2]
[ op.2]
Linearization (1)
Output Point 2
Set the value that will be
mapped to input 2.
-1,999.000 to 9,999.000
1.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3596 0x13 (19)
160
34019
float
RWES
[`iP;3]
[ ip.3]
Linearization (1)
Input Point 3
Set the value that will be
mapped to output 3.
-1,999.000 to 9,999.000
2.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3578 0xA (10)
161
34010
float
RWES
[`oP;3]
[ op.3]
Linearization (1)
Output Point 3
Set the value that will be
mapped to input 3.
-1,999.000 to 9,999.000
2.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3598 0x14 (20)
162
34020
float
RWES
[`iP;4]
[ ip.4]
Linearization (1)
Input Point 4
Set the value that will be
mapped to output 4.
-1,999.000 to 9,999.000
3.0
Instance 1
0x86 (134)
1
Map 1 Map 2
0xB
(11)
----
3580
163
34011
float
RWES
[`oP;4]
[ op.4]
Linearization (1)
Output Point 4
Set the value that will be
mapped to input 4.
-1,999.000 to 9,999.000
3.0
Instance 1
0x86 (134)
1
Map 1 Map 2
- - - -
3600 0x15 (21)
164
34021
float
RWES
[`iP;5]
[ ip.5]
Linearization (1)
Input Point 5
Set the value that will be
mapped to output 5.
-1,999.000 to 9,999.000
4.0
Instance 1
0x86 (134)
1
Map 1 Map 2
- - - -
3582 0xC (12)
165
34012
float
RWES
[`oP;5]
[ op.5]
Linearization (1)
Output Point 5
Set the value that will be
mapped to input 5.
-1,999.000 to 9,999.000
4.0
Instance 1
0x86 (134)
1
Map 1 Map 2
- - - -
3602 0x16 (22)
166
34022
float
RWES
[`iP;6]
[ ip.6]
Linearization (1)
Input Point 6
Set the value that will be
mapped to output 6.
-1,999.000 to 9,999.000
5.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3584 0xD (13)
167
34013
float
RWES
[`oP;6]
[ op.6]
Linearization (1)
Output Point 6
Set the value that will be
mapped to input 6.
-1,999.000 to 9,999.000
5.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3604 0x17 (23)
168
34023
float
RWES
[`iP;7]
[ ip.7]
Linearization (1)
Input Point 7
Set the value that will be
mapped to output 7.
-1,999.000 to 9,999.000
6.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3586 0xE (14)
169
34014
float
RWES
[`oP;7]
[ op.7]
Linearization (1)
Output Point 7
Set the value that will be
mapped to input 7.
-1,999.000 to 9,999.000
6.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3606 0x18 (24)
170
34024
float
RWES
[`iP;8]
[ ip.8]
Linearization (1)
Input Point 8
Set the value that will be
mapped to output 8.
-1,999.000 to 9,999.000
7.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3588 0xF (15)
171
34015
float
RWES
[`oP;8]
[ op.8]
Linearization (1)
Output Point 8
Set the value that will be
mapped to input 8.
-1,999.000 to 9,999.000
7.0
Instance 1
0x86 (134)
1
Map 1 Map 2
0x19
(25)
----
3608
172
34025
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
52
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`iP;9]
[ ip.9]
Linearization (1)
Input Point 9
Set the value that will be
mapped to output 9.
-1,999.000 to 9,999.000
8.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3590 0x10 (16)
173
34016
float
RWES
[`oP;9]
[ op.9]
Linearization (1)
Output Point 9
Set the value that will be
mapped to input 9.
-1,999.000 to 9,999.000
8.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3610 0x1A (26)
174
34026
float
RWES
[iP;10]
[ip.10]
Linearization (1)
Input Point 10
Set the value that will be
mapped to output 10.
-1,999.000 to 9,999.000
9.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3592 0x11 (17)
175
34017
float
RWES
[oP;10]
[op.10]
Linearization (1)
Output Point 10
Set the value that will be
mapped to input 10.
-1,999.000 to 9,999.000
9.0
Instance 1
0x86 (134)
1
Map 1 Map 2
----
3612 0x1B (27)
176
34027
float
RWES
Off
Instance 1
0x7E (126)
1
Map 1 Map 2
----
3320 0x15 (21)
123
26021
uint
RWES
[``Pu]
[`Set]
Process Value Menu
[``Fn]
[ Fn]
Process Value (1)
[`oFF] Off (62)
Function
[`alt] *Pressure to AltiSet the function that will
tude (1649)
be applied to the source or
sources.
[p;unt]
[P.unt]
Process Value (1)
Pressure Units*
Set the units that will be
applied to the source.
[`psi] Pounds per Square PSI
Inch (1671)
[pasc] Pascal (1674)
[atm] Atmosphere
(1675)
[mbr] Millibar (1672)
[torr] Torr (1673)
Instance 1
0x7E (126)
1
Map 1 Map 2
----
3334 0x1C (28)
----
26028
uint
RWES
[a;unt]
[A.unt]
Process Value (1)
Altitude Units*
Set the units that will be
applied to the source.
[`Hft] Kilofeet (1677)
[``ft] Feet (1676)
HFt
Instance 1
0x7E (126)
1
Map 1 Map 2
----
3336 0x1D (29)
----
26029
uint
RWES
[`Fil]
[ FiL]
Process Value (1)
0.0 to 60.0 seconds
Filter
Filtering smooths out the
output signal of this function block. Increase the
time to increase filtering.
0.0
Instance 1
0x7E (126)
1
Map 1 Map 2
----
3330 0x1A (26)
----
26026
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
Set
* Pressure Altitude calculation is based on the International Standard Atmosphere, 1976
Watlow EZ-ZONE ® PM PID Controller
•
53
•
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
82
6001
uint
RWES
83
6005
uint
RWES
84
6006
uint
RWES
85
6002
uint
RWES
[`dio]
[`Set]
Digital Input/Output Menu
[`dir]
[ dir]
[``Fn]
[ Fn]
[``Fi]
[ Fi]
[`o;Ct]
[ o.Ct]
Digital Input/Output (5
Output
[OtPt] Output (68)
to 6)
[iCon] Input Dry Contact
Direction
(44)
Set this function to oper- [``in] Input Voltage (193)
ate as an input or output.
[`oFF] Off (62)
[ALM] Alarm (6)
[heat] Heat (36)
[CooL] Cool (20)
[tE;o1] Timer Event Output 1 (1951)
[tE;o2] Timer Event Output 2 (1952)
[tE;o3] Timer Event Output 3 (1953)
[h;Er] Heater Error (184)
[Ent;b] Profile Event Out
B (234)
[Ent;A] Profile Event Out
A (233)
Off
Digital Output (5 to 6)
Output Function Instance
Set the instance of the
function selected above.
1 to 4
1
Digital Output (5 to 6)
Time Base Type
Set the Time Base Type
type. This parameter
is only used with PID
control, but can be set
anytime.
[`Ftb] Fixed Time Base
(34)
[`utb] Variable Time
Base (103)
Digital Output (5 to 6)
Output Function
Select what function will
drive this output.
Instance 5
0x6A (106)
5 to 6
Map 1 Map 2
1
1000 1120
Offset to next
instance (Map
1 & Map 2)
equals +30
Instance 5
0x6A (106)
5 to 6
Map 1 Map 2
5
1008 1128
Offset to next
instance (Map
1 & Map 2)
equals +30
Instance 5
0x6A (106)
5 to 6
Map 1 Map 2
6
1010 1130
Offset to next
instance (Map
1 & Map 2)
equals +30
Fixed
Time
Base
Offset to next
instance (Map
1 & Map 2)
equals +30
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
Instance 5
0x6A (106)
5 to 6
Map 1 Map 2
2
1002 1122
•
54
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`o;tb]
[ o.tb]
Parameter Name
Description
Digital Output (5 to 6)
Fixed Time Base
Set the time base for
fixed-time-base control.
Range
Default
0.1 to 60.0
1.0 seconds
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 5
0x6A (106)
5 to 6
Map 1 Map 2
3
1004 1124
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
86
6003
float
RWES
87
6009
float
RWES
88
6010
float
RWES
137
10001
uint
RW
Offset to next
instance (Map
1 & Map 2)
equals +30
[`o;Lo]
[ o.Lo]
[`o;hi]
[ o.hi]
[`leu]
[ LEv]
Digital Output (5 to 6)
Low Power Scale
The power output will
never be less than the
value specified and will
represent the value at
which output scaling
begins.
0.0 to 100.0
Digital Output (5 to 6)
High Power Scale
The power output will
never be greater than
the value specified and
will represent the value
at which output scaling
stops.
0.0 to 100.0
Digital Input (5 to 6)
Action Level
Select which action will
be interpreted as a true
state.
[high] High (37)
[LoW] Low (53)
Instance 5
0x6A (106)
5 to 6
Map 1 Map 2
9
1016 1136
0.0
Offset to next
instance (Map
1 & Map 2)
equals +30
Instance 5
0x6A (106)
5 to 6
Map 1 Map 2
1018 1138 0xA (10)
100.0
Offset to next
instance (Map
1 & Map 2)
equals +30
Instance 5
0x6E (110)
5 to 6
Map 1 Map 2
1
1320 1560
High
Offset to next
instance (Map
1 & Map 2)
equals +20
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
55
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[``Fn]
[ Fn]
Parameter Name
Description
Digital Input (5 to 6)
Action Function
Select the function that
will be triggered by a true
state for Digital Input 5
and or 6.
Range
Default
Instance 5
0x6E (110)
5 to 6
Map 1 Map 2
3
1324 1564
None
[none] None (61)
[s;stp] Start Step (1077)
[P;StS] Profile Start/Stop,
level triggered (208)
[ProF] Start Profile, edge
triggered (196)
[P;hoL] Profile Hold/
Resume, level triggered
(207)
[P;diS] Profile Disable,
level triggered (206)
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
138
10003
uint
RWES
139
10004
uint
RWES
72
8003
uint
RWES
Offset to next
instance (Map
1 & Map 2)
equals +20
[`t;da] TRU-TUNE+® Disable, level triggered (219)
[`oFF] Switch Control
Loop Off, level triggered
(90)
[MAn] Manual, level
triggered (54)
[tUnE] Tune, edge triggered (98)
[idLE] Idle Set Point,
level triggered (107)
[`F;AL] Force Alarm To Occur, level triggered (218)
[`AoF] Control Loops Off
and Alarms to Non-alarm
State, level triggered
(220)
[`SiL] Silence Alarms,
edge triggered (108)
[ALM] Alarm Reset,
edge triggered (6)
[P;LoC] Keypad Lockout,
level triggered (217)
[usr;r] User Set Restore,
edge triggered (227)
[``Fi]
[ Fi]
Digital Input (5 to 6)
Function Instance
Select which instance of
the function selected in
Action Function will be
triggered.
0 to 4
Instance 5
0x6E (110)
5 to 6
Map 1 Map 2
4
1326 1566
0
Offset to next
instance (Map
1 & Map 2)
equals +20
[LooP]
[`Set]
Control Loop Menu
[`h;Ag]
[ h.Ag]
Control Loop (1)
Heat Algorithm
Set the heat control
method.
PID
[`oFF] Off (62)
[`Pid] PID (71)
[on;of] On-Off (64)
Instance 1
0x97 (151)
1
Map 1 Map 2
3
1884 2364
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
56
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`C;Ag]
[ C.Ag]
Control Loop (1)
Cool Algorithm
Set the cool control
method.
[`oFF] Off (62)
[`Pid] PID (71)
[on;of] On-Off (64)
Off
Instance 1
0x97 (151)
1
Map 1 Map 2
4
1886 2366
73
8004
uint
RWES
[`C;Cr]
[ C.Cr]
Control Loop (1)
Cool Output Curve
Select a cool output
curve to change the
responsiveness of the
system.
[`oFF] Off (62)
[`Cr;A] Non-linear Curve
1 (214)
[`Cr;b] Non-linear Curve
2 (215)
Off
Instance 1
0x97 (151)
1
Map 1 Map 2
5
1888 2368
----
8038
uint
RWES
[`h;Pb]
[ h.Pb]
Control Loop (1)
Heat Proportional
Band
Set the PID proportional
band for the heat outputs.
0.001 to 9,999.000°F or
units
-1,110.555 to 5,555.000°C
25.0°F or
units
14.0°C
Instance 1
Map 1 Map 2
18902370
0x97
(151)
1
6
65
8009
float
RWES
[`h;hy]
[ h.hy]
Control Loop (1)
On/Off Heat Hysteresis
Set the control switching hysteresis for on-off
control. This determines
how far into the “on”
region the process value
needs to move before the
output turns on.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
3.0°F or
units
2.0°C
Instance 1
Map 1 Map 2
19002380
0x97
(151)
1
0xB (11)
66
8010
float
RWES
[`C;Pb]
[ C.Pb]
Control Loop (1)
0.001 to 9,999.000°F or
Cool Proportional
units
Band
0.001 to 5,555.000°C
Set the PID proportional
band for the cool outputs.
25.0°F or
units
14.0°C
Instance 1
Map 1 Map 2
18922372
0x97
(151)
1
7
67
8012
float
RWES
[`C;hy]
[ C.hy]
Control Loop (1)
On/Off Cool Hysteresis
Set the control switching hysteresis for on-off
control. This determines
how far into the “on”
region the process value
needs to move before the
output turns on.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
3.0°F or
units
2.0°C
Instance 1
Map 1 Map 2
19022382
0x97
(151)
1
0xC (12)
68
8013
float
RWES
[``ti]
[ ti]
Control Loop (1)
Time Integral
Set the PID integral for
the outputs.
0 to 9,999 seconds per
repeat
180 secInstance 1
onds per Map 1 Map 2
repeat
18942374
0x97
(151)
1
8
69
8006
float
RWES
[``td]
[ td]
Control Loop (1)
Time Derivative
Set the PID derivative
time for the outputs.
0 to 9,999 seconds
0
Instance 1
Map 1 Map 2
18962376
0x97
(151)
1
9
70
8007
float
RWES
seconds
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
57
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Parameter ID
71
8008
float
RWES
Instance 1
0x97 (151)
1
Map 1 Map 2
0x10
(16)
1910 2390
----
8022
uint
RWES
0
Instance 1
0x97 (151)
1
Map 1 Map 2
1912 2392 0x11 (17)
----
8034
uint
RWES
3
Instance 1
0x97 (151)
1
Map 1 Map 2
1914 2394 0x12 (18)
----
8035
uint
RWES
90.0
0x97
Instance 1
(151)
Map 1 Map 2
1 to 2
19182398
0x14 (20)
Instance 2
Map 1 Map 2
1988 2468
----
8025
float
Critical
Instance 1
0x97 (151)
1
Map 1 Map 2
1916 2396 0x13 (19)
----
8024
uint
RWES
0.0
Instance 1
0x97 (151)
1
Map 1 Map 2
----
- - - - 0x1C (28)
----
8051
float
RWES
Parameter Name
Description
[``dB]
[ db]
Control Loop (1)
Dead Band
Set the offset to the
proportional band. With
a negative value, both
heating and cooling
outputs are active when
the process value is near
the set point. A positive
value keeps heating and
cooling outputs from
fighting each other.
-1,000.0 to 1,000.0°F or
units
-556 to 556°C
0
Instance 1
Map 1 Map 2
18982378
[t;tUn]
[t.tUn]
Control Loop (1)
TRU-TUNE+™ Enable
Enable or disable the
TRU-TUNE+™ adaptive
tuning feature.
[``no] No (59)
[`YES} Yes (106)
No
[t;bnd]
[t.bnd]
Control Loop (1)
0 to 100
TRU-TUNE+™ Band
Set the range, centered
on the set point, within
which TRU-TUNE+™ will
be in effect. Use this function only if the controller
is unable to adaptive tune
automatically.
[`t;gn]
[ t.gn]
Control Loop (1)
1 to 6
TRU-TUNE+™ Gain
Select the responsiveness
of the TRU-TUNE+™
adaptive tuning calculations. More responsiveness may increase overshoot.
[A;tSP]
[A.tSP}
Control Loop (1 to 2)
Autotune Set Point
Set the set point that the
autotune will use, as a
percentage of the current
set point.
[t;Agr]
[t.Agr]
Control Loop (1)
[Undr] Under damped
Autotune Aggressive(99)
ness
[Crit] Critical damped
Select the aggressiveness
(21)
of the autotuning calcula- [OuEr] Over damped (69)
tions.
[p;dl]
[ P.dL]
Control Loop (1)
0.0 to 5.0
Peltier Delay
Set a value that will
cause a delay when
switching from heat mode
to cool mode.
Range
Default
50.0 to 200.0%
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
Data
Type
&
Read/
Write
Profibus
Index
Display
58
•
0x97
(151)
1
0xA (10)
RWES
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`UFA]
[UFA]
Control Loop (1)
User
[`oFF] Off, sets output
Auto-to-Manual Power
power to 0% (62)
Select what the controller [bPLS] Bumpless Transfer,
outputs will do when the
maintains same output
user switches control to
power, if it was less than
manual mode.
75% and stable, otherwise
0% (14)
[MAn] Fixed Power, sets
output power to Fixed
Power setting (33)
[USEr] User, sets output
power to last Fixed Power the user entered (100)
Instance 1
0x6B (107)
1
Map 1 Map 2
2182 2662 0xC (12)
----
7012
uint
RWES
[FAiL]
[FAiL]
Control Loop (1)
User
[`oFF] Off, sets output
Input Error Power
power to 0% (62)
Select what the controller [bPLS] Bumpless, mainoutputs will do when an
tains same output power,
input error switches conif it was less than 75%
trol to manual mode.
and stable, otherwise 0%
(14)
[MAn] Fixed Power, sets
output power to Fixed
Power setting (33)
[USEr] User, sets output
power to last Fixed Power the user entered (100)
Instance 1
0x6B (107)
1
Map 1 Map 2
2184 2664 0xD (13)
----
7013
uint
RWES
[MAn]
[MAn]
Control Loop (1)
Set Point Open Loop Limit 0.0
Fixed Power
Low to Set Point Open
Set the manual output
Loop Limit High (Setup
power level that will take
Page)
effect if an Input Error
Power occurs while Autoto-Manual Power is set to
Manual Fixed.
Instance 1
0x6B (107)
1
Map 1 Map 2
2180 2660 0xB (11)
----
7011
float
RWES
[`L;dE]
[ L.dE]
Control Loop (1)
[``no] No (59)
Open Loop Detect En[`YES} Yes (106)
able
Turn on the open-loop
detect feature to monitor
a closed-loop operation for
the appropriate response.
Select Yes to detect conditions that prevent the
process from changing in
a specified time frame by
a specified amount when
PID power is at 100%.
An open loop detect error
will disable the control
loop.
No
Instance 1
0x97 (151)
1
Map 1 Map 2
1922 2402 0x16 (22)
74
8039
uint
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
59
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`L;dt]
[ L.dt]
Control Loop (1)
0 to 3,600 seconds
Open Loop Detect Time
The Open Loop Detect
Deviation value must occur for this time period to
trigger an open-loop error.
Process must deviate by
the Open Loop Detect
Deviation value in this
specified time while at
100% PID to prevent an
open loop error.
240
Instance 1
0x97 (151)
1
Map 1 Map 2
1924 2404 0x17 (23)
75
8040
uint
RWES
[`L;dd]
[ L.dd]
Control Loop (1)
-1,999.000 to 9,999.000°F
Open Loop Detect Deor units
viation
-1,110.555 to 5,555.000°C
Set the value that the
process must deviate from
the set point to trigger an
open-loop error.
Process must deviate by
this value in the Open
Loop Detect Time while
at 100% PID power to
prevent an open loop
error.
10.0°F or
units
6.0°C
Instance 1
0x97 (151)
1
Map 1 Map 2
1926 2406 0x18 (24)
76
8041
float
RWES
[``rP]
[ rP]
Control Loop (1)
[`oFF] Off (62)
Ramp Action
[`Str] Startup (88)
Select when the control[StPt] Set Point Change
ler's set point will ramp to (85)
the defined end set point.
[both] Both (13)
Off
Instance 1
0x6B (107)
1
Map 1 Map 2
2186 2666 0xE (14)
56
7014
uint
RWES
[`r;SC]
[ r.SC]
Control Loop (1)
Ramp Scale
Select the scale of the
ramp rate.
Minutes
Instance 1
0x6B (107)
1
Map 1 Map 2
2188 2668 0xF (15)
57
7015
uint
RWES
[`r;rt]
[ r.rt]
Control Loop (1)
0.0 to 9,999.000°F or units 1.0°F or
Ramp Rate
units
0.0 to 5,555.000°C
Set the rate for the set
1.0°C
point ramp. Set the Ramp
Time units for the rate
with the Ramp Scale parameter.
Instance 1
0x6B (107)
1
Map 1 Map 2
2192 2672 0x11 (17)
58
7017
float
RWES
[`L;SP]
[ L.SP]
Control Loop (1)
-1,999.000 to 9,999.000°F
Minimum Set Point
or units
Set the minimum value of -1,128.000 to 5,537.000°C
the Set Point range.
-1,999°F
or units
-1,128°C
Instance 1
0x6B (107)
1
Map 1 Map 2
3
2164 2644
52
7003
float
RWES
[`h;SP]
[ h.SP]
Control Loop (1)
-1,999.000 to 9,999.000°F
Maximum Set Point
or units
Set the maximum value of -1,128.000 to 5,537.000°C
the Set Point range..
-1,999°F
or units
-1,128°C
Instance 1
0x6B (107)
1
Map 1 Map 2
4
2166 2646
53
7004
float
RWES
[hoUr] Hours (39)
[Min] Minutes (57)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
60
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Minimum Set Point to
Maximum Set Point
(Setup Page)
75.0°F or
units
24.0°C
Instance 1
Map 1 Map 2
21602640
0x6B
(107)
1
1
49
7001
float
RWES
Control Loop (1)
Idle Set Point
Set a Set Point that can
be triggered by an event
state.
Minimum Set Point to
Maximum Set Point
(Setup Page)
75.0°F or
units
24.0°C
Instance 1
Map 1 Map 2
21762656
0x6B
(107)
1
9
50
7009
float
RWES
[SP;Lo]
[SP.Lo]
Control Loop (1)
Minimum Manual
Power
Set the minimum value of
the Fixed Power range.
-100 to 100%
-100
Instance 1
0x6B (107)
1
Map 1 Map 2
5
2168 2648
54
7005
float
RWES
[SP;hi]
[SP;hi]
Control Loop (1)
-100.0 to 100.0%
Maximum Manual
Power
Set the maximum value of
the Fixed Power range.
100
Instance 1
0x6B (107)
1
Map 1 Map 2
6
2170 2650
55
7006
float
RWES
[`o;SP]
[`o;SP]
Control Loop (1)
Manual Power
Set the fixed power.
-100.0 to 100.0%
0
Instance 1
0x6B (107)
1
Map 1 Map 2
0x02 (2)
2162 2642
55
7002
float
RWES
[`C;M]
[`C;M]
Control Loop (1)
Control Mode
Select the method that
this loop will use to
control.
[`off] Off (62)
[AUto] Auto (10)
[MAn] Manual (54)
Auto
63
8001
uint
RWES
[`oFF] Off (62)
[ALM] Alarm (6)
[heat] Heat (36)
[Cool] Cool (20)
[tE;o1] Timer Event Output 1 (1951)
[tE;o2] Timer Event Output 2 (1952)
[tE;o3] Timer Event Output 3 (1953)
[h;Er] Heater Error (184)
[Ent;A] Profile Event Out
A (233)
[Ent;b] Profile Event Out
B (234)
Output 1 - Instance 1
0x6A (106)
Heat
1 to 2
Map 1 Map 2
5
Output 2 - 888 1008
Alarm
83
6005
uint
RWES
Display
Parameter Name
Description
[`C;SP]
[`C;SP]
Control Loop (1)
Set Point
Set the set point that the
controller will automatically control to.
[`id;S]
[ id.S]
Range
Instance 1
Map 1 Map 2
18802360
0x97
(151)
1
1
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[otpt]
[`Set]
Output Menu
[``Fn]
[ Fn]
Output Digital (1 to 2)
Output Function
Select what function will
drive this output.
Offset to next
instance (Map
1 & Map 2)
equals +30
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
61
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[``Fi]
[ Fi]
[`o;Ct]
[ o.Ct]
[`o;tb]
[ o.tb]
[`o;Lo]
[ o.Lo]
[`o;hi]
[ o.hi]
[`o;ty]
[ o.ty]
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
6
890 1010
Output Digital (1 to 2)
Output Function Instance
Set the instance of the
function selected above.
1 to 2
1
Output Digital (1 to 2)
Time Base Type
Set the Time Base Type
type. This parameter
is only used with PID
control, but can be set
anytime.
[`Ftb] Fixed Time Base
(34)
[`utb] Variable Time
Base (103)
Output Digital (1 to 2)
Fixed Time Base
Set the time base for
fixed-time-base control.
0.1 to 60.0 seconds (solidstate relay or switched
dc)
5.0 to 60.0 seconds (mechanical relay or no-arc
power control)
0.1 sec.
[SSR &
sw dc]
20.0 sec.
[mech,
relay,
no-arc]
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
3
884 1004
Output Digital (1 to 2)
Low Power Scale
The power output will
never be less than the
value specified and will
represent the value at
which output scaling
begins.
0.0 to 100.0%
0.0%
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
9
896 1016
Output Digital (1 to 2)
High Power Scale
The power output will
never be greater than
the value specified and
will represent the value
at which output scaling
stops.
0.0 to 100.0%
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
84
6006
uint
RWES
85
6002
uint
RWES
86
6003
float
RWES
87
6009
float
RWES
88
6010
float
RWES
95
18001
uint
RWES
Offset to next
instance (Map
1 & Map 2)
equals +30
Fixed
Time
Base
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
2
882 1002
Offset to next
instance (Map
1 & Map 2)
equals +30
Offset to next
instance (Map
1 & Map 2)
equals +30
Offset to next
instance (Map
1 & Map 2)
equals +30
100.0%
Offset to next
instance (Map
1 & Map 2)
equals +30
Instance 1
0x76 (118)
1
Map 1 Map 2
1
720 840
Volts
Output Process (1)
[uoLt] Volts (104)
Output Type
[`MA] Milliamps (112)
Select whether the process output will operate in
volts or milliamps.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
Instance 1
0x6A (106)
1 to 2
Map 1 Map 2
898 1018 0xA (10)
•
62
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[``Fn]
[ Fn]
Output Process (1)
Output Function
Set the type of function
that will drive this output.
Off
[`oFF] Off (62)
[dupl] Duplex (212)
[Cool] Cool (20)
[heat] Heat (36)
[rmt] Retransmit (213)
[Ent;b] Profile Event Out
B (234)
[Ent;A] Profile Event Out
A (233)
[ALM] Alarm (6)
Instance 1
0x76 (118)
1
Map 1 Map 2
2
722 842
96
18002
uint
RWES
[`r;Sr]
[ r.Sr]
Output Process (1)
Retransmit Source
Select the value that will
be retransmitted.
[``Ai] Analog Input (142) Analog
Input
[StPt] Set Point (85)
[CUrr] Current (22)
[``Pu] Process Value
(241)
Instance 1
0x76 (118)
1
Map 1 Map 2
3
724 844
97
18003
uint
RWES
[``Fi]
[ Fi]
Output Process (1)
Output Function Instance
Set the instance of the
function selected above.
1 to 4
1
Instance 1
0x76 (118)
1
Map 1 Map 2
4
726 846
98
18004
uint
RWES
[`S;Lo]
[ S.Lo]
Output Process (1)
-100.0 to 100.0
Scale Low
Set the scale low for process output in electrical
units. This value; in volts
or milliamps, will correspond to 0% PID power
output or range low retransmit output.
0.00
Instance 1
0x76 (118)
1
Map 1 Map 2
9
736 856
99
18009
float
RWES
[`S;hi]
[ S.hi]
Output Process (1)
-100.0 to 100.0
Scale High
Set the scale high for process output in electrical
units. This value; in volts
or milliamps, will correspond to 100% PID power
output or range high
retransmit output. .
10.00
Instance 1
0x76 (118)
1
Map 1 Map 2
0xA (10)
738 858
100
18010
float
RWES
[`r;Lo]
[ r.Lo]
Output Process (1)
-1,999.000 to 9,999.000°F
Range Low
or units
Set the minimum value
-1,128.000 to 5,537.000°C
of the retransmit value
range in process units.
When the retransmit
source is at this value, the
retransmit output will be
at its Scale Low value.
0.0°F or
units
-18°C
Instance 1
0x76 (118)
1
Map 1 Map 2
0xB (11)
740 860
101
18011
float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
63
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`r;hi]
[ r.hi]
Output Process (1)
-1,999.000 to 9,999.000°F
Range High
or units
Set the maximum value
-1,128.000 to 5,537.000°C
of the retransmit value
range in process units.
When the retransmit
source is at this value, the
retransmit output will be
at its Scale High value.
100°F or
units
38°C
Instance 1
0x76 (118)
1
Map 1 Map 2
0xC (12)
742 862
102
18012
float
RWES
[`o;CA]
[ o.CA]
Output Process (1)
Calibration Offset
Set an offset value for a
process output.
-1,999.000 to 9,999.000°F
or units
-1,110.555 to 5,555.000°C
0.0°F or
units
0.0°C
Instance 1
0x76 (118)
1
Map 1 Map 2
7
732 852
105
18007
float
RWES
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
1508 1908 0xF (15)
20
9015
uint
RWES
21
9017
uint
RWES
24
9003
float
RWES
25
9005
uint
RWES
[Alm]
[`Set]
Alarm Menu
[`A;ty]
[ A.ty]
[`Sr;A]
[ Sr.A]
[`A;hy]
[ A.hy]
[`A;Lg]
[ A.Lg]
Alarm (1 to 4)
Type
Select whether the alarm
trigger is a fixed value or
will track the set point.
Off
[`oFF] Off (62)
[PR;AL] Process Alarm (76)
[dE;AL] Deviation Alarm
(24)
Alarm (1 to 4)
Alarm Source
Select what will trigger
this alarm.
[nonE] None (61)
[``Ai] Analog Input (142)
[`Lnr] Linearization (238)
[``Pu] Process Value
(241)
[PWr] Power (73)
[`CU;r] Current RMS (179)
[CUrr] Current Read
Sample and Hold (22)
Offset to next
instance (Map
1 & Map 2)
equals +60
Alarm (1 to 4)
Hysteresis
Set the hysteresis for an
alarm. This determines
how far into the safe
region the process value
needs to move before the
alarm can be cleared.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
Alarm (1 to 4)
Logic
Select what the output
condition will be during
the alarm state.
[`AL;C] Close On Alarm
(17)
[`AL;o] Open On Alarm
(66)
----
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
15121912 0x11 (17)
Offset to next
instance (Map
1 & Map 2)
equals +60
1.0°F or
units
1.0°C
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
3
1484 1884
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Close On
Alarm
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
5
1488 1888
•
64
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`A;Sd]
[ A.Sd]
Parameter Name
Description
Range
Default
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
26
9004
uint
RWES
0x6D
(109)
1 to 4
2
18
9002
float
RWES
0x6D
(109)
1 to 4
1
19
9001
float
RWES
27
9007
uint
RWES
28
9008
uint
RWES
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
4
1486 1886
Both
Alarm (1 to 4)
[both] Both (13)
Sides
[high] High (37)
Select which side or sides [LoW] Low (53)
will trigger this alarm.
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
[`A;Lo]
[ A.Lo]
[`A;hi]
[ A.hi]
[`A;LA]
[ A.LA]
[`A;bL]
[ A.bL]
Alarm (1 to 4)
Low Set Point
If Type (Setup Page,
Alarm Menu) is set to:
process - set the process
value that will trigger a
low alarm.
deviation - set the span
of units from the Set
Point that will trigger
a low alarm. A negative
set point represents a
value below Set Point. A
positive set point represents a value above Set
Point.
-1,999.000 to 9,999.000°F
or units
-1,128.000 to 5,537.000°C
Alarm (1 to 4)
High Set Point
If Type (Setup Page,
Alarm Menu) is set to:
process - set the process
value that will trigger a
high alarm.
deviation - set the span
of units from the Set
Point that will trigger a
high alarm.
-1,999.000 to 9,999.000°F
or units
-1,128.000 to 5,537.000°C
32.0°F
or units
0.0°C
Instance 1
Map 1 Map 2
14821882
Offset to next
instance (Map
1) equals +50
Offset to next
instance (Map
2) equals +60
300.0°F
or units
150.0°C
Instance 1
Map 1 Map 2
14801880
Offset to next
instance (Map
1) equals +50
Offset to next
instance (Map
2) equals +60
Alarm (1 to 4)
[nLAt] Non-Latching (60)
Latching
[`LAt] Latching (49)
Turn Latching on or off.
A latched alarm has to be
turned off by the user.
NonInstance 1
0x6D (109)
Latching Map 1 Map 2
1 to 4
7
1492 1892
Alarm (1 to 4)
Blocking
Select when an alarm will
be blocked. After startup
and/or after the set point
changes, the alarm will be
blocked until the process
value enters the normal
range.
Off
[`oFF]
[`Str]
[StPt]
[both]
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Off (62)
Startup (88)
Set Point (85)
Both (13)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
8
14941894
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
65
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`A;Si]
[ A.Si]
[A;dSP]
[A.dSP]
Parameter Name
Description
Range
Default
Alarm (1 to 4)
[`oFF] Off (62)
Silencing
[``on] On (63)
Turn Silencing on to allow
the user to disable this
alarm.
Off
Alarm (1 to 4)
[`oFF] Off (62)
Display
[``on] On (63)
Display an alarm message
when an alarm is active.
On
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
6
1490 1890
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
29
9006
uint
RWES
30
9016
uint
RWES
31
9021
uint
RWES
----
9013
uint
W
----
9014
uint
W
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
0x10
(16)
1510 1910
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
[`A;dL]
[ A.dL]
[A;CLr]
[A.CLr]
Alarm (1 to 4)
0 to 9,999 seconds
Delay
Set the span of time that
the alarm will be delayed
after the process value exceeds the alarm set point.
Alarm (1 to 4)
Clear Request
Clear a latched alarm.
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
1520 1920 0x15 (21)
0
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
----
[`CLr] Clear (0)
[ignr] Ignore (204)
Note:
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
If an alarm is setup to
latch when active [A;CLr]
will appear on the display.
[A;Sir]
[A.Sir]
Alarm (1 to 4)
Silence Alarm
Disable alarm action.
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
1504 1904 0x0D (13)
----
[`SiL] Silence (1010)
Note:
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
If an alarm is setup to
silence an alarm, when
active [A;Sir] will appear
on the display.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
1506 1906 0x0E (14)
•
66
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[`A;St]
[`A.St]
Parameter Name
Description
Range
Default
----
Alarm (1 to 4)
[`Str] Startup (88)
Alarm State
[nonE] None (61)
Display the alarm state in [`blo] Blocked (12)
the Home Page.
[`AL;L] Alarm Low (8)
[`AL;h] Alarm High (7)
[`AL;E] Error (28)
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Instance 1
0x6D (109)
1 to 4
Map 1 Map 2
0x09 (9)
1496 1896
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
----
9009
uint
R
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
[tMr]
[`Set]
Timer Menu
[ti;En]
[ti.En]
Timer
[`YES] Yes (106)
Timer Enable
[``no] No (59)
Enable the timer function.
Yes
Instance 1
0x83 (131)
1
Map 1 Map 2
- - - -
8556 0x1D (29)
----
31029
uint
RWES
[ti;St]
[ti.St]
Timer
Timer Start Method
Select what will start the
timer.
[iMd] Immediate
Immediate
Instance 1
0x83 (131)
1
Map 1 Map 2
- - - -
8558 0x1E (30)
----
31030
uint
RWES
[SFn;A]
[SFn.A]
Timer
Source Function A
Select which input will
start or terminate the
timer.
[`FUn] Function Key
(1001)
[nonE] None (61)
[`dio] Digital I/O (1142)
Function
Key
Instance 1
0x83 (131)
1
Map 1 Map 2
0x01 (1)
- - - -
8500
----
31001
uint
RWES
[`Si;A]
[ Si.A]
Timer
Source Instance A
Select an instance of
Function A.
1 to 24
8
Instance 1
0x83 (131)
1
Map 1 Map 2
0x03 (3)
----
8504
----
31003
uint
RWES
[SFn;C]
[SFn.C]
Timer
Source Function C
Select the analog source
for the ready band.
Process
[``Pu] Process Value
Value
(241)
[nonE] None (61)
[``Ai] Analog Input (142)
[`Lnr] Linearization (238)
Instance 1
0x83 (131)
1
Map 1 Map 2
- - - -
8560 0x1F (31)
----
31031
uint
RWES
[`Si;C]
[ Si.C]
Timer
Source Instance C
Select an instance of
Function C.
1 to 24
1
Instance 1
0x83 (131)
1
Map 1 Map 2
0x21
(33)
----
8564
----
31033
uint
RWES
[SFn;D]
[SFn.D]
Timer
Source Function D
Select which input will
acknowledge the ready
band.
[`FUn] Function Key
(1001)
[nonE] None (61)
[`dio] Digital I/O (1142)
Function
Key
Instance 1
0x83 (131)
1
Map 1 Map 2
----
8562 0x20 (32)
----
31032
uint
RWES
[`Si;D]
[ Si.d]
Timer
Source Instance D
Select an instance of
Function D.
1 to 24
7
Instance 1
0x83 (131)
1
Map 1 Map 2
----
8566 0x22 (34)
----
31034
uint
RWES
[``t;r]
[ t.r]
Timer
Time Remaining
Display the time remaining on the timer.
[00;00] 00:00 to 99:59
7
Instance 1
0x83 (131)
1
Map 1 Map 2
----
- - - - 0x15 (21)
----
31021
string
R
(1049)
[`rdY] Ready Band (1942)
[rdYA] Ready Ack (1950)
[PWr] Power (73)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
67
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
----
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
Instance 1
0x83 (131)
1
Map 1 Map 2
- - - -
8542 0x16 (22)
----
31022
uint
R
[`r;bS]
[ r.bS]
Timer
Ready Band State
Display whether the process value is in the ready
band.
[`rdY]
[ rdY]
Timer
0.000 to 9999.000°F or
Ready Band
units
Set the how close the pro- 0.000 to 5555.000°C
cess value must be to the
closed loop timer set point
to be in the ready band.
5.000
Instance 1
0x83 (131)
1
Map 1 Map 2
- - - -
8544 0x17 (23)
----
31023
float
RWES
[t;For]
[t.For]
Timer
Time Format
Select the time format.
[tMS] Time
Time
Instance 1
0x83 (131)
Minutes: Map 1 Map 2
1
Seconds
0x18
(24)
- - - -
8546
----
31024
uint
RWES
[hoUr]
[hoUr]
Timer
Hours
Set the timer period
hours.
0 to 99
0
Instance 1
0x83 (131)
1
Map 1 Map 2
----
8548 0x19 (25)
----
31025
uint
RWES
[Min]
[Min]
Timer
0 to 59
Minutes
Set the timer period minutes.
0
Instance 1
0x83 (131)
1
Map 1 Map 2
0x1A
(26)
----
8550
----
31026
uint
RWES
[`SEC]
[ SEC]
Timer
Seconds
Set the timer period seconds.
10
Instance 1
0x83 (131)
1
Map 1 Map 2
- - - -
8552 0x1B (27)
----
31027
uint
RWES
[Ct;SP]
[Ct.SP]
Timer
-1999.000 to 9999.000°F
Closed Loop Timer Set
or units
Point
-1110.555 to 5555.000°C
Set the set point that will
be in effect during the
timer period.
75
Instance 1
0x83 (131)
1
Map 1 Map 2
----
8554 0x1C (28)
----
31028
float
RWES
[``St]
[ St]
Timer
1 to 3600 Seconds
Signal Time
Set the period of time
that a signal output to be
activated after the timer
period is complete. Assign
a digital output for this
function in Timer Event
Output 3.
1
Instance 1
0x83 (131)
1
Map 1 Map 2
- - - -
8588 0x2D (45)
----
31045
uint
RWES
High
Instance 1
0x6E (110)
Map 1 Map 2
1 to 2
1360 1600
1
Instance 2
Map 1 Map 2
1380 1620
137
10001
uint
RWES
[`YES] Yes (106)
[``no] No (59)
Minutes:Seconds (1943)
[thM] Time
Hours:Minutes (1944)
0 to 59
[`FUn]
[`Set]
Function Key Menu
[`leu]
[ LEv]
Function Key (1 to 2)
Active Level
The Function Key will
always power up in the
low state.
[high] High (37)
[Low] Low (53)
Pressing the Function Key
will toggle the selected
action.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
68
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
[``Fn]
[ Fn]
Parameter Name
Description
Function Key (1 to 2)
Action Function
Program the EZ Key to
trigger an action.
Functions respond to a
level state change or an
edge level change.
Range
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Data
Type
&
Read/
Write
Profibus
Index
Parameter ID
Instance 1
0x6E (110)
Map 1 Map 2
1 to 2
1364 1604
3
Instance 2
Map 1 Map 2
1384 1624
138
10003
uint
RWES
0
Instance 1
0x96 (110)
Map 1 Map 2
1 to 2
1364 1606
4
Instance 2
Map 1 Map 2
1384 1626
139
10004
uint
RWES
Default
None
[none] None (61)
[usr;r] User Set Restore,
edge triggered (227)
[P;LoC] Keypad Lockout,
level triggered (217)
[ALM] Alarm Reset,
edge triggered (6)
[`SiL] Silence Alarms,
edge triggered (108)
[`AoF] Control Loops Off
and Alarms to Non-alarm
State, level triggered
(220)
[`F;AL] Force Alarm To Occur, level triggered (218)
[idLE] Idle Set Point,
level triggered (107)
[tUnE] Tune, edge triggered (98)
[MAn] Manual Mode,
level triggered (54)
[`oFF] Switch Control
Loop Off, level triggered
(90)
[`t;da] TRU-TUNE+® Disable, level triggered (219)
[P;diS] Profile Disable,
level triggered (206)
[P;hoL] Profile Hold/
Resume, level triggered
(207)
[ProF] Start Profile, edge
triggered (196)
[P;StS] Profile Start/Stop,
level triggered (208)
[s;stp] Start Step (1077)
[``Fi]
[ Fi]
Function Key (1 to 2)
0 to 4
Function Instance
Select which instance the
EZ Key will affect. If only
one instance is available,
any selection will affect it.
[gLbL]
[`Set]
Global Menu
[`C_F]
[ C_F]
Global
Display Units
Select which scale to use
for temperature.
[```F] °F (30)
[```C] °C (15)
°F
Instance 1
0x67 (103)
1
Map 1 Map 2
5
1838 2308
110
3005
uint
RWES
[AC;LF]
[AC.LF]
Global
AC Line Frequency
Set the frequency to the
applied ac line power
source.
[``50] 50 Hz (3)
[``60] 60 Hz (4)
60 Hz
Instance 1
0x6A (106)
1
Map 1 Map 2
4
886 1006
89
1034
uint
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
69
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
Ramp
Time
Instance 1
0x7A (122)
1
Map 1 Map 2
----
4414 0x26 (38)
----
22038
uint
RWE
Global
[StPt] Set Point (85)
Profile Type
[`Pro] Process (75)
Set the profile startup to
be based on a set point or
a process value.
Set Point
Instance 1
0x7A (122)
1
Map 1 Map 2
8
2534 4354
----
22008
uint
RWE
[`GSE]
[ gSE]
Global
[`oFF] Off (62)
Guaranteed Soak En[``on] On (63)
able
Enables the guaranteed
soak deviation function in
profiles.
Off
Instance 1
0x7A (122)
1
Map 1 Map 2
6
2530 4350
----
22006
uint
RWE
[GSd1]
[gSd1]
Global
Guaranteed Soak Deviation 1
Set the value of the deviation band that will be
used in all profile step
types. The process value
must enter the deviation
band before the step can
proceed.
0.0 to 9,999.000°F or units 10.0°F or
units
0.0 to 5,555.000°C
6.0°C
Instance 1
0x7A (122)
1
Map 1 Map 2
7
2532 4352
----
22007
float
RWE
[`Si;a]
[ Si.A]
Global
Source Instance A
Set the digital source
for Wait for Event 1 in
profile.
5 to 6
5
Instance 1
0x7A (122)
1
Map 1 Map 2
----
4390 0x1A (26)
----
22060
uint
RWES
[`Si;B]
[ Si.b]
Global
Source Instance B
Set the digital source
for Wait for Event 2 in
profile.
5 to 6
5
Instance 1
7A (122)
1
Map 1 Map 2
- - - -
4392 0x1B (27)
----
22061
uint
RWES
[poti]
[Poti]
Global
0 to 9999 seconds
Power Off Time
If profile is running and
power is lost, profile
will resume where it
left off provided time set
has not expired prior to
power restoration.
0
Instance 1
7A (122)
1
Map 1 Map 2
- - - -
4484 0x49 (73)
----
22073
uint
RWE
[R;typ]
[R.tyP]
Global
Ramping Type
[P;typ]
[P.tyP]
[rate] Ramp Rate (81)
[``ti] Ramp Time (143)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
Set
* Available with PM4, PM8 and PM9 models only
Watlow EZ-ZONE ® PM PID Controller
•
70
•
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
----
----
Parameter ID
----
Data
Type
&
Read/
Write
[sutb]
[Sutb]
Global
-2.00 to 2.00 Percent
Synchronized Variable
Time Base
Used to acquire tighter
accuracy when running
a profile or using the
Timer feature. A setting
of +0.01 would equate to
approximately +9 seconds/day (faster) where
a setting of -0.01 would
equate to approximately
-9 seconds/day (slower).
0.00
[C;led]
[C.LEd]
Global
Communications LED
Action
Turns comms LED on or
off for selected comms
ports.
Comm
port 1
Instance 1
0x6A (103)
1
Map 1 Map 2
1856 2326 0x0E (14)
----
3014
uint
RWES
[2one]
[Zone]
Global
[`off] Off (62)
Zone
[``on] On (63)
Turns Zone LED on or off
based on selection.
On
Instance 1
0x6A (103)
1
Map 1 Map 2
----
2350 0x1A (26)
----
3026
uint
RWES
[Chan]
[Chan]
Global
[`off] Off (62)
Channel
[``on] On (63)
Turns Channel LED on or
off based on selection.
On
Instance 1
0x6A (103)
1
Map 1 Map 2
0x1B
(27)
----
2352
----
3027
uint
RWES
[d;prs]
[dPrS]
Global
Display Pairs
Defines the number of
Display Pairs.
1 to 10
2
Instance 1
0x6A (103)
1
Map 1 Map 2
----
2354 0x1C (28)
----
3028
uint
RWES
[`d;ti]
[ d.ti]
Global
0 to 60
Display Time
Time delay in toggling between display pairs.
0
Instance 1
0x6A (103)
1
Map 1 Map 2
----
2356 0x1D (29)
----
3029
uint
RWES
[USr;S]
[USr.S]
Global
Restore Settings From
Save all of this controller's settings to the selected set.
[SEt1] User Set 1 (101)
[SEt2] User Set 2 (102)
[none] None (61)
None
Instance 1
Map 1 Map 2
26 26
0x(101)
1
0xE (14)
118
1014
uint
RWE
[USr;r]
[USr.r]
Global
Save Settings As
Save all of the controller's settings to the selected set.
[FCty]
[none]
[SEt1]
[SEt2]
Factory (31)
None (61)
User Set 1 (101)
User Set 2 (102)
None
Instance 1
Map 1 Map 2
24 24
0x65
(101)
1
0xD (13)
117
1013
uint
RWE
Modbus
Instance 1
0x96 (150)
1
Map 1 Map 2
7
2492 2972
----
17009
uint
RWE
[Con1] Comm port 1
(1189)
[`off] Off (62)
----
Profibus
Index
float
RWES
[CoM]
[`SEt]
Communications Menu
[PCoL]
[PCoL]
Communications
[`Std] Standard Bus
Protocol
(1286)
Set the protocol of this
[Mod] Modbus RTU
controller to the protocol
(1057)
that this network is using.
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
71
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[`Ad;S]
[ Ad.S]
Communications
1 to 16
Standard Bus Address
Set the network address
of this controller. Each device on the network must
have a unique address.
The Zone Display on the
front panel will display
this number.
1
Instance 1
0x96 (150)
1
Map 1 Map 2
1
2480 2960
----
17001
uint
RWE
[Ad;M]
[Ad.M]
Communications
1 to 247
Modbus Address
Set the network address
of this controller. Each device on the network must
have a unique address.
1
Instance 1
0x96 (150)
1
Map 1 Map 2
2
2482 2962
----
17007
uint
RWE
[bAUd]
[bAUd]
Communications
Baud Rate
Set the speed of this controller's communications
to match the speed of the
Modbus serial network.
9,600
Instance 1
0x96 (150)
1
Map 1 Map 2
3
2484 2964
----
17002
uint
RWE
[`PAr]
[ PAr]
Communications
[none] None (61)
Parity (1)
[EuEn] Even (191)
Set the parity of this con- [`odd] Odd (192)
troller to match the parity of the Modbus serial
network.
None
Instance 1
0x96 (150)
1
Map 1 Map 2
4
2486 2966
----
17003
uint
RWE
[M;hL]
[M.hL]
Communications
Modbus Word Order
Select the word order of
the two 16-bit words in
the floating-point values.
[Lohi] Low-High (1331)
[hiLo] High-Low (1330)
Low-High
Instance 1
0x96 (150)
1
Map 1 Map 2
5
2488 2968
----
17043
uint
RWE
[`C_f]
[ C_F]
Communications
Display Units
Select whether this communications channel
will display in Celsius or
Fahrenheit.
[```f] Fahrenheit (30)
[```C] Celsius (15)
F
Instance 1
0x96 (150)
Map 1 Map 2
1
2490 2970
6
----
17050
uint
RWE
----
17059
198
17051
[9600] 9,600 (188)
[`19;2] 19,200 (189)
[`38;4] 38,400 (190)
Note:
Applies to Modbus only.
[Map]
[Map]
Communications
1 to 2
Data Map
If set to 1 the control will
use PM legacy mapping.
If set to 2 the control will
use new mapping to accommodate new functions.
If 9th digit of part
number
is a 1, 2,
3 or D.
[`nU;S]
[ nV.S]
Communications
[`yes] Yes (106)
Non-Volatile Save
[``no] No (59)
If set to Yes all values
written to the control will
be saved in EEPROM.
Yes
•
72
----
Instance 1
0x96 (150)
1
Map 1 Map 2
8
2494 2974
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
----
•
----
uint
RWE
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
Setup Page
Display
Parameter Name
Description
Range
Default
CIP
Modbus RelaClass
tive
Instance
Address
Attribute
hex (dec)
Profibus
Index
Parameter ID
Data
Type
&
Read/
Write
[rtC] (Available with PM4, PM8 and PM9 models only)
[`SEt]
Real Time Clock Menu
[hoUr]
[hoUr]
Real Time Clock
Hours
Set the current time.
0 to 23
0
Instance 1
0x88 (136)
1
Map 1 Map 2
3
----
4004
----
36003
uint
RW
[Min]
[Min]
Real Time Clock
Minutes
Set the current time.
0 to 59
0
Instance 1
0x88 (136)
1
Map 1 Map 2
4
----
4006
----
36004
uint
RW
[dow]
[doW]
Real Time Clock
[`sun] Sunday (1565)
Day of Week
[mon] Monday (1559)
Set the current day of the [`tue] Tuesday (1560)
week.
[wed] Wednesday
(1561)
[thUr] Thursday (1562)
[`fri] Friday (1563)
[`sat] Saturday (1564)
Sun
Instance 1
0x88 (136)
1
Map 1 Map 2
2
----
4002
----
36002
uint
RW
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
73
•
R: Read
W: Write
E: EEPROM
S: User
Set
Chapter 6 Setup Page
7
Chapter 7: Profiling Page
Navigating the Profiling Page
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no submenus will appear.
Profile Setup
First, consider some foundational profile setup features that once configured, will apply to all configured profiles.
The screen shot below (EZ-ZONE Configurator software) graphically shows the settings (shaded green)that
will apply to all profiles; e.g., if Guaranteed Soak is not enabled here this feature will not be available in any
individual profile configuration.
Some of those features that apply to all profiles are listed below with a brief description of their function.
- Ramping Type (Ramp Time or Ramp Rate) which changes the profile set point based on a set interval of
time or set rate.
- Profile Type (Set Point
or Process) determines
whether a step (any step
changing the set point)
of a profile will begin by
using the process value
(Process) or the last Set
Point (Set Point).
- Guaranteed Soak Enable, when set to On
makes this feature available in all profiles. If
Guaranteed Soak Enable
is on, use Guaranteed
Soak Deviation 1 to 2 to
set the value for the corresponding loop. Set the
deviation or band above
or below the working set
point where this condition must be met before
the profile can proceed.
Note:
Changes made in the
Profiling Page take effect
on the next pass through the step. Changes made in the Profile Status Page effect the current step being
executed and do not update the step setting in the profiling page. These parameters should only be changed
by knowledgeable personnel and with caution.
Once these global profile features are configured, the next step will require navigation to the Profiling Page.
Here, each desired ramp and soak profile will be configured.
To navigate to the Profile Page from the front panel, follow the steps below:
1. From the Home Page, press and hold the Advance Key ‰ for approximately five seconds. The profile
prompt [ProF] will appear in the lower display and the profile number (e.g. [``p1]) appears in the upper
display.
Watlow EZ-ZONE ® PM PID Controller
•
74
•
Chapter 7 Profiling Page
2. Press the Up ¿ or Down ¯ key to change to another profile (1 to 4).
3. Press the Advance Key
‰
to move to the selected profiles first step.
4. Press the Up ¿ or Down ¯ keys to move through and select the step type.
5. Press the Advance Key
‰
to move through the se- lected step settings.
6. Press the Up ¿ or Down ¯ keys to change the steps settings.
7. Press the Infinity Key ˆ at any time to return to the step number prompt.
8. Press the Infinity Key ˆ again to return to the profile number prompt.
9. From any point press and hold the Infinity Key ˆ for two seconds to return to the Home Page.
If using EZ-ZONE Configurator software, simply click on the plus sign next to Profiles in the left hand column, as shown in the screen shot below.
Notice in the screen shot to the right some fields or parameters are not selectable (grayed out) based on the
Step Type that is selected.
Starting a Profile
There are several ways to start a profile. Some of the examples that follow requires that certain optional
hardware be available on the control. If you are uncertain as to how your control is equipped, compare the
part number of your control to the "Ordering Information" page found in the Appendix of this Users Guide.
Ways to start a profile:
- Function Key
- Digital Input
- Profile Request
Configuring the Function Key to
Start and Stop a Profile
1. Navigate to the Setup Page
and then the Function menu.
From the Home Page, press
and hold the ¿ or Down ¯
key for approximately six
seconds where the upper display will show [``ai] and
the lower display will show
[`set] .
2. Press the Up ¿ or Down ¯
key to navigate to the Function [`fUn] menu.
3. Press the Advance Key ‰ to
enter this menu. The upper
display will show [ hig h]
and the lower display will
show [`leu] .
4. Press the Up ¿ or Down ¯
keys to select the level that
will start the profile (high or
low).
5. Press the Advance Key ‰ to
select the function. In this
example, select Profile Start
/ Stop [ p ; s ts] .
6. Press the Advance Key
‰
to select the function instance (Profile to start).
7. Return to the Home Page by pressing and holding the Infinity Key ˆ for approximately three seconds.
Note:
The state of the EZ-Function Key (high or low) is maintained with each successive push of the key.
Watlow EZ-ZONE ® PM PID Controller
•
75
•
Chapter 7 Profiling Page
Configuring a Digital Input to Start and Stop a Profile
1. Navigate to the Setup Page and then the Digital I/O menu. From the Home Page, press and hold the ¿ or
Down ¯ key for approximately six seconds where the upper display will show [``ai] and the lower display will show [`set] .
2. Press the Up ¿ or Down ¯ key to navigate to the Digital I/O menu. Upper display will show [`dio] and
the lower display will show [`set] .
3. Press the Advance Key
‰
where the first available digital instance will be displayed in the upper display.
4. Press the Up ¿ or Down ¯ key to select the input of choice.
5. Press the Advance Key
[iCon] .
‰
to select the direction (input or output). In this example, select Dry Contact
6. Select the level (high or low) that will activate the function by pressing the Advance Key
per display will show [ hig h] and the lower display will show [`leu] .
‰
where the up-
7. Press the Up ¿ or Down ¯ keys to select the level that will start the profile (high = closed or low = open).
8. Press the Advance Key
‰
to select the function. In this example, select Profile Start / Stop [ p ; s ts] .
9. Press the Advance Key
‰
to select the function instance (Profile to start).
10.Return to the Home Page by pressing and holding the Infinity Key ˆ for approximately three seconds.
Starting a Profile from the Operations Page
1. Navigate to the Operations Page and then the Profile Status menu. From the Home Page, press and hold
the ¿ or Down ¯ key for approximately three seconds where the upper display will show [``ai] and the
lower display will show [oper] .
2. Press the Up ¿ or Down ¯ key to navigate to the Profile Status [ p ; s ta] menu.
3. Press the Advance Key
will show [ p ; s tr] .
‰
to enter this menu. The upper display will show [```1] and the lower display
4. Press the Up ¿ or Down ¯ keys to select the Profile or Step to start. In this example select 1.
5. Press the Advance Key ‰ to select the Profile Action Request. The upper display will show [none] and
the lower display will show [ p ; a Cr] .
6. Press the Up ¿ or Down ¯ keys to select the Profile start. The upper display will show [Prof] and the
lower display will show [ p ; a Cr] .
Note:
As soon as the Green Advance key is pressed (step 7 below) the designated Profile or Step (as determined in
step 4 above) will start.
7. Press the Advance Key ‰ to select whether Event 1 will be on or off. The upper display will show [`off]
and the lower display will show [ ent1] .
Note:
This setting will temporally override the profile configuration.
8. Press the Up ¿ or Down ¯ keys to select whether Event 1 will be on or off. This will immediately drive
the Event to the specified state regardless of the Profile configuration.
9. Press the Advance Key ‰ to select whether Event 2 will be on or off. The upper display will show [`off]
and the lower display will show [ ent2] . The event state will continue as when the profile ended and may
be toggled in the Profile Status Menu.
10.Press the Up ¿ or Down ¯ keys to select whether Event 2 will be on or off. This will immediately drive
the Event to the specified state regardless of the Profile configuration.
11.Press the Advance Key ‰ to see the current Jump Count. The upper display will show [```0] and the
lower display will show [``jC] .
12.Return to the Home Page by pressing and holding the Infinity Key ˆ for approximately three seconds.
Ending a Profile from the Operations Page
Watlow EZ-ZONE ® PM PID Controller
•
76
•
Chapter 7 Profiling Page
1. Navigate to the Operations Page and then the Profile Status menu. From the Home Page, press and hold
the ¿ or Down ¯ key for approximately three seconds where the upper display will show [``ai] and the
lower display will show [oper] .
2. Press the Up ¿ or Down ¯ key to navigate to the Profile Status [ p ; s ta] menu.
3. Press the Advance Key
will show [ p ; s tr] .
‰
to enter this menu. The upper display will show [```1] and the lower display
4. Press the Advance Key ‰ to select the Profile Action Request. The upper display will show [none] and
the lower display will show [ p ; a Cr] .
6. Press the Up ¿ or Down ¯ keys to select the End. The upper display will show [`end ] and the lower display will show [ p ; a Cr] .
7. Press the Advance Key
‰
to end the Profile.
8. Return to the Home Page by pressing and holding the Infinity Key ˆ for approximately three seconds.
Starting a Profile from the Home Page
1. When at the Home Page, press the Advance Key ‰ to locate Profile Start and select the file or step num-
ber to start. The upper display will show [```1] and the lower display will show [ p ; s t1] .
2. Press the Up ¿ or Down ¯ key to choose the file or step number.
3. Press the Advance Key ‰ to select the Profile Action Request. The upper display will show [none] and
the lower display will show [ p ; a C1] .
4. Press the Up ¿ or Down ¯ keys to select the Profile Start. The upper display will show [Prof] and the
lower display will show [ p ; a C1] .
5. Press the Infinity Key to return Home. The Profile will Start
Ending a Profile from the Home Page
1. Press the Advance Key ‰ to select the Profile Action Request. The upper display will show [none] and
the lower display will show [ p ; a C1] .
2. Press the Up ¿ or Down ¯ keys to select the End. The upper display will show [~End ] and the lower
display will show [ p ; a C1]
3. Press the Infinity Key to return Home. The Profile will End.
Profiling Parameters
[``p1]
[prof] Profile (1 to 4)
[```1]
[``P1] Profile [1 to 4] Step (1 to 40)
[s;typ] Step Type
[t;SP1] Target Set Point Loop 1
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[rate] Ramp Rate
[W;P1] Wait For Process 1
[w;E1] Wait Event 1
[WE;2] Wait Event 2
[dow] Day of Week
[``js] Jump Step
[``jC] Jump Count
[`EnD] End Type
[Ent1] Event 1
[Ent2] Event 2
Watlow EZ-ZONE ® PM PID Controller
•
77
•
Chapter 7 Profiling Page
Profiling Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative Address
----
----
CIP
Class
ParamInstance
eter ID
Attribute
hex (dec)
Data
Type
&
Read/
Write
[``P1]
[prof]
Profiling Menu
[``p1]
[ P1] to
[``p4]
[ P4]
Profile [1 to 4] Step
Select a step to edit or view.
[S;typ]
[S.typ]
Step Type
Select a step type.
[t;SP1]
[t.SP1]
[hoUr]
[hoUr]
[Min]
[Min]
[~SEC]
[ SEC]
1 to 10 [profile 1]
11 to 20 [profile 2]
21 to 30 [profile 3]
31 to 40 [profile 4]
[UStP] Unused Step (50)
[SoAH] Soak (87)
[`W;E] Wait For Event (144)
Note:
[W;Pr] Wait For Process (209)
When configuring the profile
type there will be a Ramp
[W;bo] Wait For Both (210)
Time prompt as delivered from [``JL] Jump (116)
the factory (default). If rate is
[`End] End (27)
desired navigate to the Setup
[CloC] Wait For Time (1543)
Page and then the Global Menu
[``ti] Ramp Time (143)
where Ramping Type can be
[rate] Ramp Rate (81)
changed.
Step Type Parameters
Target Set Point Loop 1
When Step Type is Ramp Time
or Ramp Rate, enter the Set
Point for loop 1 to ramp to for
this step.
-1,999.000 to 9,999.000°F or
units
-1,128 to 5,537.000°C
Step Type Parameters
Hours
When Step Type is Time, Soak,
or Wait For Time, enter Hours
(plus Minutes and Seconds) for
this step.
0 to 99
Unused
----
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
1
2570 4500
----
----
21001
uint
RWE
21002
float
RWE
21003
uint
RWE
21004
uint
RWE
21005
uint
RWE
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
0.0°F or
units
-18°C
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
2
2572 4502
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
0
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
0 to 59
Step Type Parameters
Minutes
When Step Type is Ramp Time,
Soak, or Wait For Time enter
Minutes (plus Hours and Seconds) for this step.
0
0 to 59
Step Type Parameters
Seconds
When Step Type is Ramp Time,
Soak, or Wait For Time enter
Seconds (plus Hours and Minutes) for this step.
0
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
4
2576 4506
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
5
2578 4508
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
3
2574 4504
•
78
•
R: Read
W: Write
E: EEPROM
S: User Set
Chapter 7 Profiling Page
Profiling Page
Display
[rate]
[rAtE]
[W;P1]
[W.P1]
[WE;1]
[WE.1]
Parameter Name
Description
Step Type Parameters
Ramp Rate
When Step Type is Ramp Rate,
enter the rate for ramping in
degrees or units per minute.
Range
Default
0 to 9,999.000°F or units per
minute
0 to 5,555.000°C per minute
0.0°F or
units
-18.0°C
Step Type Parameters
Wait Event 2
When Step Type is Wait for
Event or Wait For Both, select
the event state that must
be satisfied during this step.
[`oFF] Off (62)
[``on] On (63)
[nonE] None (61)
Off
Step Type Parameters
Day of Week
When Step Type is Wait for
Ramp Time, the profile waits
until this setting (Day of Week)
along with Hours, Minutes and
Seconds are met.
21006
float
RWE
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
2590 4520 0xB (11)
21011
float
RWE
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
9
2586 4516
21009
uint
RWE
21010
uint
RWE
21041
uint
RWE
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
[`oFF] Off (62)
[``on] On (63)
[nonE] None (61)
Off
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
2588 4518 0xA (10)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
Wait Event 1 can be mapped
to any available digital input
(5 or 6). Navigate to the Global Menu in the Setup Page
to find and modify Source
Instance A [`s;ia] is Wait
Event 1 and Source Instance
B [`s;ib] is Wait Event 2.
[dow]
[dow]
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
2580 4510
6
Data
Type
&
Read/
Write
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
Wait Event 1 can be mapped
to any available digital input
(5 or 6). Navigate to the Global Menu in the Setup Page
to find and modify Source
Instance A [`s;ia] is Wait
Event 1 and Source Instance
B [`s;ib] is Wait Event 2.
[WE;2]
[WE.2]
CIP
Class
ParamInstance
eter ID
Attribute
hex (dec)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
-1,999.000 to 9,999.000°F or
Step Type Parameters
units
Wait For Process 1
When Step Type is Wait for
-1,128.000 to 5,537.000°C
Process or Wait For Both, enter
wait for process value for analog input 1 before proceeding in
profile.
Step Type Parameters
Wait Event 1
When Step Type is Wait for
Event or Wait For Both, select
the event state that must
be satisfied during this step.
0.0
Modbus
Relative Address
[``ed] Every Day (1567)
[`wd] Week days (1566)
[`sun] Sunday (1565)
[mon] Monday (1559)
[`tue] Tuesday (1560)
[wed] Wednesday (1561)
[thUr] Thursday (1562)
[`fri] Friday (1563)
[`sat] Saturday (1564)
Sunday
Offset to next
instance Map 2
equals +100)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
•
79
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
----
4580 0x29 (41)
•
R: Read
W: Write
E: EEPROM
S: User Set
Chapter 7 Profiling Page
Profiling Page
Display
[~~JS]
[ JS]
[~~JC]
[ JC]
[~End]
[ End]
Parameter Name
Description
Range
Default
Step Type Parameters
Jump Step
When Step Type is Jump, this
setting specifies which step to
jump back to. Jump Step must
be a lower step number than
the current step number.
1 to 40
Step Type Parameters
Jump Count
When Step Type is Jump, this
specifies the number of jumps
to repeat. A value
of 0 creates an infinite loop.
Loops can be nested four deep.
0 to 9,999
Step Type Parameters
End Type
When Step Type is End, this
setting specifies what the controller will do when this profile
ends.
[`oFF] Control Mode set to Off
(62)
[Hold] Hold last Set Point in
the profile (47)
[USEr] User, reverts to previous set point (100)
0
[Ent2]
[Ent2]
CIP
Class
ParamInstance
eter ID
Attribute
hex (dec)
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
2592 4522 0xC (12)
Data
Type
&
Read/
Write
21012
uint
RWE
21013
uint
RWE
21014
uint
RWE
21007
uint
RWE
21008
uint
RWE
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
0
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
2594 4524 0xD (13)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Off
[`oFF] Off (62)
Step Type Parameters
Event 1
[``on] On (63)
When Step Type is not Unused
Step, select whether Event Output 1 or 2 is on or off during
this step.
Off
[`oFF] Off (62)
Step Type Parameters
Event 2
[``on] On (63)
When Step Type is not Unused
Step, select whether Event Output 1 or 2 is on or off during
this step.
Off
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
7
2582 4512
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
8
2584 4514
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with other interfaces.
Watlow EZ-ZONE ® PM PID Controller
Instance 1
0x79 (121)
Map 1 Map 2 1 to (40)
2596 4526 0xE (14)
Offset to next
instance (Map
1 equals +50,
Map 2 equals
+100)
Note:
End Hold does not affect the
control mode, only the Set
Point. The profile will return to
the control mode before a profile
was started.
Ent1]
[Ent1]
Modbus
Relative Address
•
80
•
R: Read
W: Write
E: EEPROM
S: User Set
Chapter 7 Profiling Page
Display
Step Type
Description
Parameters in Step Type
----
[UStP]
[UStP]
Step Types
Unused Step
This is an empty step that can be used to plan for future steps to be
inserted or temporarily deactivate a step in a profile. Change step type
back when the step should be active again.
[``ti]
[ ti]
Step Types
Ramp Time
If Ramping Type in the Global Menu of the Setup Page is set for Ramp
Time, the state of up to 2 event outputs may be set or maintained.
[tg;S1] Target Set Point Loop 1
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[Ent1] Event 1
[Ent2] Event 2
[rAtE]
[rAtE]
Step Types
Ramp Rate
If Ramping Type in the Global Menu of the Setup Page is set for Ramp
Rate, specify the rate of change in degrees or units per minute. The
state of up to 2 event outputs may be set or maintained.
[tg;S1] Target Set Point Loop 1
[rAtE] Ramp Rate
[Ent1] Event 1
[Ent2] Event 2
[SoAh]
[SoAh]
Step Types
Soak
A Soak Step maintains the last Target Set Points for the designated
time. The state of up to 2 event outputs may be set or maintained.
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[Ent1] Event 1
[Ent2] Event 2
[CLoC]
[CLoC]
Step Types
Wait For Time
A Wait for Time Step is available with the real-time calendar clock feature. This allows the program to wait for a specified day and time before
proceeding to the next step. Used to have the profile execute steps everyday or only weekdays. The state of up to 2 event outputs may be set
or maintained.
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[dow] Day of Week
[Ent1] Event 1
[Ent2] Event 2
[`W;E]
[ W.E]
Step Types
Wait For Event
A Wait for Event Step will wait for the two Wait for Event states (1 to 2)
to match the specified state. The state of up to 2 event outputs may be
set or maintained.
[WE;1] Wait Event 1
[WE;2] Wait Event 2
[Ent1] Event 1
[Ent2] Event 2
[W;pr]
[W.Pr]
Step Types
Wait For Process
A Wait for Process Step will wait for Process Value 1 or 2 to match the
Wait for Process Value. The state of up to 2 event outputs may be set or
maintained.
[W;pi] Wait for Process Instance
[W;p1] Wait for Process 1 Value
[Ent1] Event 1
[Ent2] Event 2
[W;bo]
[W.bo]
Step Types
Wait For Both
A Wait For Process and Event Step will wait for Process Value 1 or 2 to
match the Wait for Process 1 value, and/or the two Wait Event states to
match the specified state. The state of up to 2 event outputs may be set
or maintained.
[W;pi] Wait for Process Instance
[W;p1] Wait for Process 1 Value
[WE;1] Wait Event 1
[WE;2] Wait Event 2
[Ent1] Event 1
[Ent2] Event 2
[``JL]
[ JL]
Step Types
Jump
A Jump step will repeat previous steps a number of times designated in Jump Count. Jumps can be nested up to four deep. The state of
up to 2 event outputs may be set or maintained. This step type not
available in subroutine.
[``JS]
[``JC]
[Ent1]
[Ent2]
[`End]
[ End]
Step Types
End
An End Step will end the profile and set the control modes and set
points to match the End Type. The state of up to 2 event outputs may be
set or maintained. The event outputs will not be set off unless specifically stated in this step. If a profile does not have an End Step, the profile continues until step 40, then stops and maintains the last set points
and control modes.
[`End] End Type
[Ent1] Event 1
[Ent2] Event 2
Watlow EZ-ZONE ® PM PID Controller
•
81
•
Jump Step
Jump Count
Event 1
Event 2
Chapter 7 Profiling Page
8
Chapter 8: Factory Page
Navigating the Factory Page
To go to the Factory Page from the Home Page, press and hold both the Advance ‰ and Infinity ˆ keys for
six seconds.
• Press the Advance Key ‰ to enter the menu of choice.
• If a submenu exists (more than one instance), press the Up ¿ or Down ¯ key to select and then press the
Advance Key ‰ to enter.
• Press the Up ¿ or Down ¯ key to move through available menu prompts.
• Press the Infinity Key ˆ to move backwards through the levels: parameter to submenu; submenu to menu;
menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds to return to the Home Page.
Note:
Some of these menus and parameters may not appear, depending on the controller's options. See model
number information in the Appendix for more information. If there is only one instance of a menu, no submenus will appear.
[CUSt]
[FCty] Custom Setup Menu
[```1]
[CUSt] Custom Setup (1 to 20)
[`par] Parameter
[`iid] Instance ID
[`LoC]
[FCty] Security Setting Menu
[`LoC] Security Setting
[LoC;o] Operations Page
[LoC;P] Profiling Page
[pas;e] Password Enable
[RloC] Read Lock
[SLoC] Write Security
[loC;l] Locked Access Level
[roll] Rolling Password
[pas;u] User Password
[pas;a] Administrator Password
[ULoC]
[FCty] Security Setting Menu
[Code] Public Key
[Pass] Password
[diAg]
[FCty] Diagnostics Menu
[diAg] Diagnostics
[``Pn] Part Number
[`rEu] Software Revision
[S;bld] Software Build Number
[``Sn] Serial Number
[dAtE] Date of Manufacture
[`CAL]
[FCty] Calibration Menu
[```1]
[`Cal] Calibration (1 to 2)
[`Mu] Electrical Measurement
[ELi;o] Electrical Input Offset
[ELi;S] Electrical Input Slope
[ELo;o] Electrical Output Offset
[ELo;s] Electrical Output Slope
[``Pn] Part Number
[Code] Public Key
Watlow EZ-ZONE ® PM PID Controller
•
82
•
Chapter 8 Factor y Page
Factory Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
[Cust]
[fcty]
Custom Menu
[`par]
[ Par]
Custom
Parameter 1 to 20
Select the parameters that
will appear in the Home
Page.
The Parameter 1 value will
appear in the upper display of the Home Page. It
cannot be changed with
the Up and Down Keys
in the Home Page.
The Parameter 2 value will
appear in the lower display in the Home Page. It
can be changed with the
Up and Down Keys, if the
parameter is a writable
one.
Scroll through the other
Home Page parameters
with the Advance Key
‰.
Note:
Display Pairs affect the
pairing of custom parameters on the Home
page. For more information on Display Pairs see
the section in this guide
entitled "Modifying the
Display Pairs"
[`iid]
[ iid]
Custom (1 to 20)
Instance ID
Select which instance of
the parameter will be selected.
[nonE] None
[`Pro] Process
[`i;CA] Calibration Offset
[`C_F] Display Units
[USr;r] Save Settings As
[`A;Lo] Low Set Point
[`A;hi] High Set Point
[`A;hy] Hysteresis
[CUSt] Custom Menu
[StPt] Set Point
[AC;pu] Active Process
Value
[AC;SP] Active Set Point
[``op] Manual Power
[`AUt] Autotune
[`C;M] Control Mode
[`h;Pr] Heat Power
[`C;Pr] Cool Power
[``ti] Time Integral
[``td] Time Derivative
[``db] Dead Band
[`h;Pb] Heat Proportional
Band
[`h;hy] On/Off Heat Hysteresis
[`C;Pb] Cool Proportional
Band
[`C;hy] On/Off Cool Hysteresis
[`r;rt] Ramp Rate
[t;tUn] TRU-TUNE+® Enable
[idLE] Idle Set Point
[P;Str] Profile Start
[P;ACr] Profile Action Request
[gSd1] Guaranteed Soak
Deviation 1
See:
Home
Page
----
----
----
14005
uint
RWES
----
----
----
----
14003
uint
RWES
----
----
----
3002
uint
RWE
1 to 4
[`LoC]
[FCty]
Security Setting Menu
[LoC;o]
[LoC.o]
Security Setting
Operations Page
Change the security level
of the Operations Page.
1 to 3
2
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
83
•
Chapter 8 Factor y Page
Factory Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
[LoC;P]
[LoC.P]
Security Setting
Profiling Page
Change the security level
of the Profiling Page.
1 to 3
3
----
----
----
3008
uint
RWE
[pas;e]
[LoC.P]
Security Setting
Password Enable
Set to on to require
a password for menu
changes.
[`off] Off
[``on] On
Off
----
----
----
3009
uint
RWE
[rLoC]
[rLoC]
Security Setting
Read Lock
Set the read security
clearance level. The user
can access the selected
level and all lower levels.
If the Set Lockout Security
level is higher than the
Read Lockout Security,
the Read Lockout Security level takes priority.
1 to 5
5
----
----
----
3010
uint
RWE
[SLoC]
[SLoC]
Security Setting
Write Security
Set the write security
clearance level. The user
can access the selected
level and all lower levels.
If the Set Lockout Security
level is higher than the
Read Lockout Security,
the Read Lockout Security level takes priority.
0 to 5
5
----
----
----
3011
uint
RWE
[loC;l]
[LoC.L]
Security Setting
Locked Access Level
Determines user level
menu visibility when
Password Enable is set to
on. See Features section
under Password Security.
1 to 5
5
----
----
----
3016
uint
RWE
[roll]
[roLL]
Security Setting
Rolling Password
When power is cycled a
new Public Key will be
displayed and User Password changes.
[`off] Off
[``on] On
Off
----
----
----
3019
uint
RWE
[pas;u]
[PAS.u]
Security Setting
User Password
Used to acquire access
to menus made available
through the Locked Access
Level setting.
10 to 999
63
----
----
----
3017
uint
RWE
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
84
•
Chapter 8 Factor y Page
Factory Page
Display
Parameter Name
Description
[pas;a]
[PAS.A]
Security Setting
Administrator Password
Used to acquire full access to all menus including disabling or changing
passwords.
Range
Default
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
10 to 999
156
----
----
----
3018
uint
RWE
[ULoC]
[FCty]
Security Setting Menu
[Code]
[CodE]
Security Setting
Public Key
If Rolling Password
turned on, generates a
random number when
power is cycled. If Rolling
Password is off fixed number will be displayed. The
key can be used to gain
access when the password
is not known.
Customer Specific
0
----
----
----
3020
uint
R
[pass]
[PASS]
Security Setting
Password
Enter the User or Administrator password to gain
access. Exit this menu
and re-enter Factory Page,
Security menu after valid
password is supplied.
-1999 to 9999
0
----
----
----
3022
int
RW
[diag]
[fcty]
Diagnostics Menu
[``Pn]
[ Pn]
Diagnostics
Part Number
Display this controller's
part number.
15 characters
----
----
0x65
(101)
1
9
115
1009
string
RWE
[`rEu]
[ rEu]
Diagnostics
Software Revision
Display this controller's
firmware revision number.
1 to 10
----
----
0x65
(101)
1
0x11 (17)
116
1003
string
R
[S;bLd]
[S.bLd]
Diagnostics
Software Build Number
Display the firmware
build number.
0 to 2,147,483,647
----
Instance 1
Map 1 Map 2
8
8
0x65
(101)
1
5
----
1005
dint
R
[``Sn]
[ Sn]
Diagnostics
Serial Number
Display the serial number.
0 to 2,147,483,647
----
----
0x65
(101)
1
0x20 (32)
----
1032
string
RWE
[dAtE]
[dAtE]
Diagnostics
Date of Manufacture
0 to 2,147,483,647
----
Instance 1
Map 1 Map 2
14 14
0x65
(101)
1
8
----
1008
dint
RWE
No Display
Diagnostics
Hardware ID
Display the Hardware ID.
0 to 2,147,483,647
----
Instance 1
Map 1 Map 2
0
0
0x65
(101)
1
1
----
1001
dint
R
Display the date code (YYWW). Where YY = year
and WW= week..
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
85
•
Chapter 8 Factor y Page
Factory Page
Display
Parameter Name
Description
No Display
Diagnostics
Firmware ID
Display the Firmware ID.
Range
Default
Modbus
Relative Address
CIP
Data
Class
Type
Profibus ParamInstance
&
Index eter ID
Attribute
Read/
hex (dec)
Write
0 to 2,147,483,647
----
Instance 1
Map 1 Map 2
2
2
0x65
(101)
1
2
----
1002
dint
R
----
Instance 1
Map 1 Map 2
400 400
Instance 2
Map 1 Map 2
480 490
0x68
(104)
1 to 2
0x15 (21)
----
4021
float
R
[`CAL]
[FCty]
Calibration Menu
[`Mu]
[ Mv]
Calibration (1 to 2)
Electrical Measurement
Read the raw electrical
value for this input in the
units corresponding to
the Sensor Type (Setup
Page, Analog Input Menu)
setting.
-3.4e38 to 3.4e38
[ELi;o]
[ELi.o]
Calibration (1 to 2)
Electrical Input Offset
Change this value to calibrate the low end of the
input range.
-1,999.000 to 9,999.000
0.0
Instance 1
Map 1 Map 2
378 378
Instance 2
Map 1 Map 2
458 468
0x68
(104)
1 to 2
0xA (10)
----
4010
float
RWES
[ELi;S]
[ELi.S]
Calibration (1 to 2)
Electrical Input Slope
Adjust this value to calibrate the slope of the input value.
-1,999.000 to 9,999.000
1.0
Instance 1
Map 1 Map 2
380 380
Instance 2
Map 1 Map 2
460 470
0x68
(104)
1 to 2
0xB (11)
----
4011
float
RWES
[ELo;o]
[ELo.o]
Calibration (1 or 3)
Electrical Output Offset
Change this value to calibrate the low end of the
output range.
Menu 2 calibrates output
3.
-1,999.000 to 9,999.000
0.0
----
----
----
18005
----
[ELo;S]
[ELo.S]
Calibration (1 or 3)
Electrical Output Slope
Adjust this value to calibrate the slope of the output value.
Menu 2 calibrates output
3.
-1,999.000 to 9,999.000
1.0
----
----
----
18006
----
[``Pn]
[ Pn]
Calibration (1 to 3)
Part Number
Displays current setting
for control model number.
[fCty] Factory
[User] User
Factory
----
----
----
----
uint
R
[Code]
[CodE]
Calibration (1 to 3)
Public Key
Changes the control to
the user model number or
back to the original model
number as shown on the
side of the control.
[2501] User model number
[`606] Factory model
number
(User is either Express, if
ordered as Standard, or
Standard, if ordered as
Express.)
4999
----
----
----
----
uint
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be
read with other interfaces.
R: Read
W: Write
E: EEPROM
S: User
If there is only one instance of a menu, no submenus will appear.
Set
Watlow EZ-ZONE ® PM PID Controller
•
86
•
Chapter 8 Factor y Page
9
Chapter 9: Features
Changing PM PID Model Number to PM User Mode. . . . . . . . . . . . . . . 88
How to Change the PM Control Model Number to User Mode. . . . . . . . 89
How to Restore Original Factory Mode PM Model Number. . . . . . . . . . 89
Saving and Restoring User Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 89
Programming the Home Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Tuning the PID Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Manual Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Autotuning with TRU‑TUNE+®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Calibration Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Set Point Low Limit and High Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Scale High and Scale Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Range High and Range Low. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Ten Point Linearization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
NO-ARC Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Retransmitting a Process Value or Set Point. . . . . . . . . . . . . . . . . . . . . 96
Cool Output Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Control Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Output Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Auto (closed loop) and Manual (open loop) Control . . . . . . . . . . . . . . . 97
On-Off Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Proportional Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Proportional plus Integral (PI) Control. . . . . . . . . . . . . . . . . . . . . . . . . 100
Proportional plus Integral plus Derivative (PID) Control . . . . . . . . . . . 100
Dead Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Variable Time Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Single Set Point Ramping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Timer Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Process and Deviation Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Alarm Set Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Alarm Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Alarm Latching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Alarm Silencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Alarm Blocking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Open Loop Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Programming the EZ Key/s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Using Lockout and Password Security . . . . . . . . . . . . . . . . . . . . . . . 107
Modbus - Using Programmable Memory Blocks . . . . . . . . . . . . . . . . 109
Software Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Watlow EZ-ZONE ® PM PID Controller
•
87
•
Chapter 9 Features
Changing PM PID Model Number to PM User Mode
EZ-ZONE PM PID firmware revisions of 13 and above allow the user to switch between a PM PID control to
a PM Express PID. Switching to a PM Express PID eliminates the complexity of the PM PID control by allowing the user to operate with a simplified menu structure.
Note:
When switching from a PID control to an Express version, optional PM hardware (even though installed)
and firmware features not available in a PM Express will no longer work. To see exactly what is impacted
by this change, compare the chart below to the ordering information page in this document.
Controller
PM _ _ _ _ _ - _ _ _ _ B _ _
EZ-ZONE® PID Controller Changes to PM Express
Red-green 7-segment displays
Package Size
No Change
Primary Function
C
R
T
B
J
N
E
S
PID Controller with Universal Input
Changes to C
PID Controller with Universal Input
Changes to J
Custom Firmware
Power Supply
1
2
3
4
100 to 240V Å (ac)
Changes to 1
15 to 36VÎ (dc) and 24VÅ (ac)
Changes to 3
Output 1 and 2 Hardware Options
CA
CH
CC
CJ
CK
EA
EH
EC
EJ
EK
FA
FC
FJ
FK
AK
KH
KK
Output 1
Switched dc/open collector
Switched dc/open collector
Switched dc/open collector
Switched dc/open collector
Switched dc/open collector
Mechanical relay 5 A, form C
Mechanical relay 5 A, form C
Mechanical relay 5 A, form C
Mechanical relay 5 A, form C
Mechanical relay 5 A, form C
Universal process
Universal process
Universal process
Universal process
None
Solid-state relay 0.5 A, form A
Solid-state relay 0.5 A, form A
Output 2
None
NO-ARC 15 A power control
Switched dc
Mechanical relay 5 A, form A
Solid-state relay 0.5 A, form A
None
NO-ARC 15 A power control
Switched dc
Mechanical relay 5 A, form A
Solid-state relay 0.5 A, form A
None
Switched dc (cannot use variable time base)
Mechanical relay 5 A, form A (cannot use variable time base)
Solid-state relay 0.5 A, form A (cannot use variable time base)
Solid-state relay 0.5 A, form A
NO-ARC 15 A power control
Solid-state relay 0.5 A, form A
Communications Options or Additional Digital I/O
None
- Standard Bus EIA-485 always included - all models
Future Options
None
Isolated Input Option
B
Changes to Express
AA
12
AB
AC
AG
XX
Standard EZ-ZONE face plate
Class 1, Div. 2 (Not available with Integrated Limit Controller or mechanical relay outputs)
EZ-ZONE logo and no Watlow name
No logo and no Watlow name
Conformal coating
Custom firmware, overlays, parameter settings
Custom Options
Watlow EZ-ZONE ® PM PID Controller
•
88
•
Chapter 9 Features
How to Change the PM Control Model Number to User Mode
1. Enter Factory Page [FCty], Calibration Menu [`CAL] via front panel by pressing the Infinity ˆ or Reset
Key and the Advance Key ‰ together or using EZ-ZONE Configurator software.
2. Once there, use the Advance Key ‰ to navigate to the Part Number [``Pn] prompt (green display). The
red display will show factory [fCtY] indicating the factory model number as shown on the decal located
on the side of the control is currently in effect.
3. Push the Advance Key ‰, Public Key [Code] prompt will be displayed in the green display and the number [4999] in the red display.
4. Using the up or down Arrow Keys enter [2501] and push the Advance Key ‰ to execute the change. The
controller will reboot and the new controller model number is in effect. All previous settings are lost and
the controller must be reprogrammed for the application. Be sure to label the controller with the new
model number for future reference.
Note:
As noted above, when switching from a PM Standard to a PM Express version, optional hardware (even
though installed) may no longer work, and all settings will default to those of the selected model.
How to Restore Original Factory Mode PM Model Number
1. Enter Factory Page [FCty], Calibration Menu [`CAL] via front panel by pressing the Infinity ˆ or Reset
Key and the Advance Key ‰ together or using EZ-ZONE Configurator software.
2. Once there, use the Advance Key ‰ to navigate to the Part Number [``Pn] prompt (green display). The
red display will show user [USEr] indicating the user’s selected model number is currently in effect.
3. Push the Advance Key ‰, Public Key [Code] prompt will be displayed in the green display and the number [4999] in the red display.
4. Using the up or down arrow keys enter [~606] and push the Advance Key ‰ to execute the change. The
controller will reboot and the new controller model number is in effect. All previous settings are lost and
the controller must be reprogrammed for the application. Be sure to label the controller with the new
model number for future reference.
Note:
When switching from a PM Express back to the original model number all original optional hardware will
again be enabled for use (assuming all original hardware is still installed). Also, when executing this step
the controller will be factory defaulted back to the original model number (as shown on the side of the control) at zone address 1. This appropriate User's Guide would once again apply to this control.
Saving and Restoring User Settings
Recording setup and operations parameter settings for future reference is very important. If you unintentionally change these, you will need to program the correct settings back into the controller to return the equipment to operational condition.
After you program the controller and verify proper operation, use Restore Settings From [USr;S] (Setup
Page, Global Menu) to save the settings into either of two files in a special section of memory. If the settings
in the controller are altered and you want to return the controller to the saved values, use User Restore Set
[USr; r] (Setup Page, Global Menu) to recall one of the saved settings.
A digital input or the Function Key can also be configured to restore user settings.
Note:
Only perform the above procedure when you are sure that all the correct settings are programmed into the
controller. Saving the settings overwrites any previously saved collection of settings. Be sure to document all
the controller settings.
Note:
When restoring factory defaults, I/O assemblies for Modbus, DeviceNet, Profibus and Ethernet along with
the zone address will be overwritten when restoring factory defaults.
Watlow EZ-ZONE ® PM PID Controller
•
89
•
Chapter 9 Features
Programming the Home Page
Watlow’s patented user-defined menu system improves operational efficiency. The user-defined Home Page
provides you with a shortcut to monitor or change the parameter values that you use most often.
You can create your own Home Page with as many as 20 of the active parameters. When a parameter normally located in the Setup Page or Operations Page is placed in the Home Page, it is accessible through both.
If you change a parameter in the Home Page, it is automatically changed in its original page. If you change a
parameter in its original page it is automatically changed in the Home Page.
The default parameters will automatically appear in the Home Page.
Change the list of parameters in the Home Page from the Custom Menu [CUSt] (Factory Page).
Tuning the PID Parameters
Autotuning
Temperature
When an autotune is performed on the EZ-ZONE PM, the set point is used to calculate the tuning set point.
For example, if the active set point is 200° and Autotune Set Point [A;tSP] (Operations Page, Loop Menu)
is set to 90 percent, the autotune function utilizes 180° for tuning. This is also how autotuning works in previous Watlow Winona controllers. In addition, changing the active set point in previous controllers causes the
autotune function to restart; where with the EZ-ZONE PM changing the set point after an autotune has been
started has no affect.
A new feature in EZ-ZONE PM products will alMinimum Set Point changes while the control is autotuning, this includes while running a profile or ramping. When the auto tune is initially started it will use the
current set point and will disregard all set point changes until the tuning process is complete. Once complete,
the controller will then use the new set point.
This is why it is a good idea to enter the active set point before initiating an autotune.
Autotuning calculates the optimum heating and/or cooling PID parameter settings based on the system's
response. Autotuning can be enabled whether or not TUNE-TUNE+® is enabled. The PID settings generated by the autotune will be used until
Process Set Point
the autotune feature is rerun, the PID
Autotune
begins
Autotune complete
values are manually adjusted or TRU®
TUNE+ is enabled.
To initiate an autotune, set Autotune
[`AUt] (Operations Page, Loop Menu) to
[`YES]. You should not autotune while
a profile is running. If the autotune
cannot be completed in 60 minutes, the
Autotune Set Point
autotune will time-out and the original
(90 percent of Process Set Point)
settings will take effect.
The lower display will flash between
[tUnE] and the set point while the autotuning is underway. The temperature
must cross the Autotune Set Point five
times to complete the autotuning process. Once complete, the controller controls at the normal set point, using the
new parameters.
Select a set point for the tune with
Time
Autotune Set Point. The Autotune Set
Point is expressed as a percent of the Set Point.
If you need to adjust the tuning procedure's aggressiveness, use Autotune Aggressiveness [T;Agr] (Setup
Page, Loop Menu). Select under damped  [Undr] to bring the process value to the set point quickly. Select over damped [ouer] to bring the process value to the set point with minimal overshoot. Select critical
damped [Crit] to balance a rapid response with minimal overshoot.
Watlow EZ-ZONE ® PM PID Controller
•
90
•
Chapter 9 Features
Manual Tuning
In some applications, the autotune process may not provide PID parameters for the process characteristics
you desire. If that is the case, you may want to tune the controller manually.
1. Apply power to the controller and establish a set point typically used in your process.
2. Go to the Operations Page, Loop Menu, and set Heat Proportional Band [`h;Pb] and/or Cool Proportional
Band [`C;Pb] to 5. Set Time Integral [``ti] to 0. Set Time Derivative [``td] to 0.
3. When the system stabilizes, watch the process value. If it fluctuates, increase the Heat Proportional
Band or Cool Proportional Band value in 3 to 5° increments until it stabilizes, allowing time for the system to settle between adjustments.
4. When the process has stabilized, watch Heat Power [`h;Pr] or Cool Power [`C;Pr] (Operations Page,
Monitor Menu). It should be stable ±2%. At this point, the process temperature should also be stable, but
it will have stabilized before reaching the set point. The difference between the set point and actual process value can be eliminated with Integral.
5. Start with an Integral value of 6,000 and allow 10 minutes for the process temperature to reach the set
point. If it has not, reduce the setting by half and wait another 10 minutes. Continue reducing the setting
by half every 10 minutes until the process value equals the set point. If the process becomes unstable, the
Integral value is too small. Increase the value until the process stabilizes.
6. Increase Derivative to 0.1. Then increase the set point by 11° to 17°C. Monitor the system’s approach to
the set point. If the process value overshoots the set point, increase Derivative to 0.2. Increase the set
point by 11° to 17°C and watch the approach to the new set point. If you increase Derivative too much, the
approach to the set point will be very sluggish. Repeat as necessary until the system rises to the new set
point without overshoot or sluggishness.
For additional information about autotune and PID control, see related features in this chapter.
Autotuning with TRU‑TUNE+®
The TRU-TUNE+ ® adaptive algorithm will optimize the controller's PID values to improve control of dynamic
processes. TRU-TUNE+ ® monitors the process variable and adjusts the control parameters automatically to
keep your process at set point during set point and load changes. When the controller is in the adaptive control mode, it determines the appropriate output signal and, over time, adjusts control parameters to optimize
responsiveness and stability. The TRU-TUNE+® feature does not function for on-off control.
The preferred and quickest method for tuning a loop is to establish initial control settings and continue
with the adaptive mode to fine tune the settings.
Setting a controller's control mode to tune starts this two-step tuning process. (See Autotuning in this
chapter.) This predictive tune determines initial, rough settings for the PID parameters. Then the loop automatically switches to the adaptive mode which fine tunes the PID parameters.
Once the process variable has been at set point for a suitable period (about 30 minutes for a fast process to
roughly two hours for a slower process) and if no further tuning of the PID parameters is desired or needed,
TRU‑TUNE+ ® may be turned off. However, keeping the controller in the adaptive mode allows it to automatically adjust to load changes and compensate for differing control characteristics at various set points for processes that are not entirely linear.
Once the PID parameters have been set by the TRU‑TUNE+® adaptive algorithm, the process, if shut
down for any reason, can be restarted in the adaptive control mode.
Turn TRU‑TUNE+® on or off with TRU‑TUNE+® Enable [t;tUn] (Setup Page, Loop Menu).
Use TRU‑TUNE+ ® Band [t;bnd] (Setup Page, Loop Menu) to set the range above and below the set point
in which adaptive tuning will be active. Adjust this parameter only in the unlikely event that the controller
is unable to stabilize at the set point with TRU‑TUNE+ ® Band set to auto (0). This may occur with very fast
processes. In that case, set TRU‑TUNE+™ Band to a large value, such as 100.
Use TRU‑TUNE+ ® Gain [`t;gn] (Setup Page, Loop Menu) to adjust the responsiveness of the adaptive
tuning calculations. Six settings range from 1, with the most aggressive response and most potential overshoot (highest gain), to 6, with the least aggressive response and least potential for overshoot (lowest gain).
The default setting, 3, is recommended for loops with thermocouple feedback and moderate response and
overshoot potential.
Watlow EZ-ZONE ® PM PID Controller
•
91
•
Chapter 9 Features
Before Tuning
Before autotuning, the controller hardware must be installed correctly, and these basic configuration parameters must be set:
• Sensor Type [`SEn] (Setup Page, Analog Input Menu), and scaling, if required;
• Function [``Fn] (Setup Page, Output Menu) and scaling, if required.
How to Autotune a Loop
1. Enter the desired set point or one that is in the middle of the expected range of set points that you want
to tune for.
2. Disable TRU-TUNE+ ®.
3. Initiate an autotune. (See Autotuning in this chapter.)
4. Enable TRU-TUNE+ ® only after autotune is complete.
When autotuning is complete, the PID parameters should provide good control. As long as the loop is in the
adaptive control mode, TRU-TUNE+ ® continuously tunes to provide the best possible PID control for the process.
ç
WARNING! During autotuning, the controller sets the output to 100 percent and attempts to drive the process variable toward
the set point. Enter a set point and heat and cool power limits that are within the safe operating limits of your system.
Inputs
Calibration Offset
Calibration offset allows a device to compensate for an inaccurate sensor, lead resistance or other factors that
affect the input value. A positive offset increases the input value, and a negative offset decreases the input
value.
The input offset value can be viewed or changed with Calibration Offset [`i;CA] (Operations Page, Analog
Input Menu).
Negative Calibration Offset will
compensate for the difference
between the Sensor Reading and
the Actual Temperature
Temperature
Temperature Reading
from Sensor
Actual Process Temperature
Time
Calibration
Before performing any calibration procedure, verify that the displayed readings are not within published
specifications by inputting a known value from a precision source to the analog input. Next, subtract the displayed value with the known value and compare this difference to the published accuracy range specification
for that type of input.
Use of the Calibration Offset [`i;CA] parameter found in the Operations Page [oPEr] , Analog Input
Menu [``Ai] shifts the readings across the entire displayed range by the offset value. Use this parameter to
compensate for sensor error or sensor placement error. Typically this value is set to zero.
Equipment required while performing calibration: Obtain a precision source for millivolts, volts, milWatlow EZ-ZONE ® PM PID Controller
•
92
•
Chapter 9 Features
liamperes or resistance depending on the sensor type to be calibrated. Use copper wire only to connect the
precision source to the controller’s input. Keep leads between the precision source and controller as short as
possible to minimize error. Use a precision volt/ohm meter capable of reading values to 4 decimal places or
better. Prior to calibration, connect this volt/ohm meter to the precision source to verify accuracy.
Actual input values do NOT have to be exactly the recommended values, but it IS critical that the actual
value of the signal connected to the controller be accurately known to at least four digits.
Calibration of Analog Inputs:
To calibrate an analog input, you will need to provide a source of two electrical signals or resistance values
near the extremes of the range that the application is likely to utilize. See recommended values below:
Sensor Type
Precision
Source Low
Precision
Source High
thermocouple
0.000 mV
50.000 mV
millivolts
0.000 mV
50.000 mV
volts
0.000V
10.000V
milliamps
0.000 mA
20.000 mA
100 Ω RTD
50.00 Ω
350.0 Ω
1,000 Ω RTD
500.0 Ω
3,500 Ω
thermistor 5 kΩ
50.00
5,000
thermistor 10 kΩ
150.0
10,000
thermistor 20 kΩ
1,800
20,000
thermistor 40 kΩ
1,700
40,000
potentiometer
0.000
1,200
Note:
The user may only calibrate one sensor type. If the calibrator interferences with open thermocouple detection, set Sensor Type [`SEn] in Setup Page [`SEt], Analog Input Menu [``Ai] to millivolt [`Mu] instead
of Thermocouple [``tC] to avoid interference between the calibrator and open thermocouple detect circuit
for the duration of the calibration process. Be sure to set sensor type back to the thermocouple type utilized.
1.
2.
Disconnect the sensor from the controller.
Record the Calibration Offset [`i;CA] parameter value in the Operations Page [oPEr] , Analog Input
Menu [``Ai] then set value to zero.
3. Wire the precision source to the appropriate controller input terminals to be calibrated. Do not have any
other wires connected to the input terminals. Please refer to the Install and Wiring section of this document for the appropriate connections.
4. Ensure the controller sensor type is programmed to the appropriate Sensor Type [`SEn] to be utilized
in the Setup Page [`SEt] , Analog Input Menu [``Ai] .
5. Enter Factory Page [FCty ] , Calibration Menu [`CAL] via RUI or EZ-ZONE Configurator Software.
6. Select the Calibration [CAL] input instance to be calibrated. This corresponds to the analog input to be
calibrated.
7. Set Electrical Input Slope [ELi;S] to 1.000 and Electrical Input Offset [ELi; o ] to 0.000 (this will cancel
any prior user calibration values)
8. Input a Precision Source Low value. Read Electrical Measurement value [`Mu] of controller via
EZ-Configurator or RUI. This will be referred to as Electrical Measured Low. Record low value
______________
9. Input a Precision Source High value.
10. Read Electrical Measurement value [`Mu] of controller via EZ-Configurator or RUI. This will be referred to as Electrical Measured High. Record high value ______________
11. Calculated Electrical Input Slope = (Precision High – Precision Low) / (Electrical Measured High - Electrical Measured Low). Calculated Slope value ___________
12. Calculated Electrical Input Offset = Precision Low - (Electrical Input Slope * Measured Low). Calculated
Offset value ___________
13. Enter the calculated Electrical Input Slope [ELi;S] and Electrical Input Offset [ELi; o ] .
14. Exit calibration menu.
Watlow EZ-ZONE ® PM PID Controller
•
93
•
Chapter 9 Features
Calibration of Analog Inputs: (cont.)
15. Validate calibration process by utilizing a calibrator to the analog input.
16. Enter calibration offset as recorded in step 2 if required to compensate for sensor error.
Setting Electrical Input Slope [ELi;S] to 1.000 and Electrical Input Offset [ELi; o ] to 0.000, restores factory
calibration as shipped from factory.
Filter Time Constant
Filtering smoothes an input signal by applying a first-order filter time constant to the signal. Filtering the
displayed value makes it easier to monitor. Filtering the signal may improve the performance of PID control
in a noisy or very dynamic system.
Adjust the filter time interval with Filter Time [`FiL] (Setup Page, Analog Input Menu).
Example: With a filter value of 0.5 seconds, if the process input value instantly changes from 0 to 100 and re-
Unfiltered Input Signal
Temperature
Temperature
Filtered Input Signal
Time
Time
Filter Time Constant
mained at 100, the display will indicate 100 after five time constants of the filter value or 2.5 seconds.
Sensor Selection
You need to configure the controller to match the input device, which is normally a thermocouple, RTD or
process transmitter.
Select the sensor type with Sensor Type [`Sen] (Setup Page, Analog Input Menu).
Set Point Low Limit and High Limit
The controller constrains the set point to a value between a Minimum Set Pont and a Maximum Set Pont.
Set the set point limits with Minimum Set Point [`L;SP] and Maximum Set Point [`h;SP] (Setup Page,
High Limit of selected functional range
Gas Pressure
Range High Range (between High Limit of Sensor and Range Low)
Set Point High
Set Point Range (must be between Range High and Range Low)
Set Point Low
Range Low Range (between Low Limit of Sensor and Range High)
Low Limit of selected functional range
Range Low and Range High
Loop Menu).
There are two sets of set point low and high limits: one for a Set Point, another for Manual Power.
Scale High and Scale Low
When an analog input is selected as process voltage or process current input, you must choose the value of voltage or current to be the low and high ends. For example, when using a 4 to 20 mA input, the scale low value
would be 4.00 mA and the scale high value would be 20.00 mA. Commonly used scale ranges are: 0 to 20 mA, 4
Watlow EZ-ZONE ® PM PID Controller
•
94
•
Chapter 9 Features
Scale High and Scale Low (cont.)
to 20 mA, 0 to 5V, 1 to 5V and 0 to 10V.
You can create a scale range representing other units for special applications. You can reverse scales from
high values to low values for analog input signals that have a reversed action. For example, if 50 psi causes a 4
mA signal and 10 psi causes a 20 mA signal.
Scale low and high low values do not have to match the bounds of the measurement range. These along with
range low and high provide for process scaling and can include values not measureable by the controller. Regardless of scaling values, the measured value will be constrained by the electrical measurements of the hardware.
Select the low and high values with Scale Low [`S;Lo] and Scale High [`S;hi]. Select the displayed range
with Range Low [`r;Lo] and Range High [`r;hi] (Setup Page, Analog Input Menu).
Range High and Range Low
With a process input, you must choose a value to represent the low and high ends of the current or voltage range. Choosing these values allows the controller’s display to be scaled into the actual working units of
measurement. For example, the analog input from a humidity transmitter could represent 0 to 100 percent
relative humidity as a process signal of 4 to 20 mA. Low scale would be set to 0 to represent 4 mA and high
scale set to 100 to represent 20 mA. The indication on the display would then represent percent humidity and
range from 0 to 100 percent with an input of 4 to 20 mA.
Select the low and high values with Range Low [`r;Lo] and Range High [`r;hi] (Setup Page, Analog Input Menu).
Ten Point Linearization
The user specifies the unit of measurement and then each data point by entering
an input point value and a corresponding
output point value. Each data point must
be incrementally higher than the previous point. The linerization function will
interpolate data points linearly in between
specified data points.
Temperature
The linearization function allows a user to re-linearize a value read from an analog input. There are 10 data
points used to compensate for differences between the sensor value read (input point) and the desired value
(output point). Multiple data points enable compensation for non-linear differences between the sensor readings and target process values over the
thermal or process system operating range.
Input Point 10
Sensor reading differences can be caused
9
Reading from Sensor
by sensor placement, tolerances, an inaccu8
Output Point 10
without
Linearization
rate sensor or lead resistance.
67
(Actual Value)
4
3
2
5
Offset Zone
Input Point 1
Output Point 1
Reading from Sensor
with Linearization
(Displayed Value)
No Offset
Note:
Output Point 1 will be the minimum
Time
value that can be displayed, and Output
Point 10 will be the maximum value that can be displayed. Consider setting Output Point 1 to the minimum operating range, and Output Point 10 to the maximum operating range; for that sensor type.
Outputs
Duplex
Certain systems require that a single process output control both heating and cooling outputs. An EZ-ZONE
PM controller with a process output can function as two separate outputs.
With a 4 to 20mA output the heating output will operate from 12 to 20mA (0 to +100 percent) and the cooling output will operate from 12 to 4mA (0 to -100 percent).
In some cases this type of output is required by the device that the EZ-ZONE PM controls, such as a
three-way valve that opens one way with a 12 to 20mA signal and opens the other way with a 4 to 12mA signal. This feature reduces the overall system cost by using a single output to act as two outputs.
Watlow EZ-ZONE ® PM PID Controller
•
95
•
Chapter 9 Features
Duplex (cont.)
Outputs 1 and 3 can be ordered as process outputs. Select duplex [dUPL] as the Output Function [``Fn]
(Setup Page, Output Menu). Set the output to volts [uoLt] or milliamps [`MA] with Output Type [`o;ty].
Set the range of the process output with Scale Low [`S;Lo] and Scale High [`S;hi].
NO-ARC Relay
A NO-ARC relay provides a significant improvement in the life of the output relay over conventional relays.
Conventional mechanical relays have an expected life of 100,000 cycles at the rated full-load current. The
shorter life for conventional relays is due to the fact that when contacts open while current is flowing metal
degradation occurs. This action produces unavoidable electrical arcing causing metal to transfer from one
contact to the other. The arcing conditions continue on each subsequent contact opening until over time the
resistance through the contacts increases causing the contacts to increase in temperature. Eventually, the
contacts will weld together and the relay remains in the on state.
The Watlow NO-ARC relay is a hybrid relay. It uses a mechanical relay for the current load and a triac
(solid-state switch) to carry the turn-on and turn-off currents. NO-ARC relays extend the life of the relay
more than two million cycles at the rated full-load current.
Although a NO-ARC relay has significant life advantages, a few precautions must be followed for acceptable usage:
Do not use:
• hybrid relays for limit contactors. A limit or safety device must provide a positive mechanical break on all
hot legs simultaneously;
• dc loads with hybrid relays. The triacs used for arc suppression will turn off only with ac line voltage;
• hybrid switches to drive any inductive loads, such as relay coils, transformers or solenoids;
• cycle times less than five seconds on hybrid switches;
• on loads that exceed 264V ac through relay;
• on loads that exceed 15 amperes load;
• on loads less than 100 mA;
• NO-ARC relays in series with other NO-ARC relays.
Retransmitting a Process Value or Set Point
Output Scale
The retransmit feature allows a process output to provide an analog signal that represents the set point or
process value. The signal may serve as a remote set point for another controller or as an input for a chart recorder documenting system performance over time.
In choosing the type of retransmit signal the operator must take into account the input impedance of the
device to be retransmitted to and the required signal type, either voltage or milliamps.
Typically applications might Range High
use the retransmit option to record one of the variables with a
chart recorder or to generate a
set point for other controls in a
multi-zone application.
Output 1 can be ordered
as process outputs. Select retransmit [rMt] as the Output Function [``Fn] (Setup
Page, Output Menu). Set the
output to volts [uoLt] or milRange Low
liamps [`MA] with Output
Scale Low
Scale High
Retransmit Source
Type [`o;ty]. Select the signal
to retransmit with Retransmit
Retransmit
Source [`r;Sr].
Set the range of the process
output with Scale Low [`S;Lo] and Scale High [`S;hi]. Scale the retransmit source to the process output with
Range Low [`r;Lo] and Range High [`r;hi]. When the retransmit source is at the Range Low value, the retransmit output will be at its Scale Low value. When the retransmit source is at the Range High value, the
retransmit output will be at its Scale High value.
Watlow EZ-ZONE ® PM PID Controller
•
96
•
Chapter 9 Features
Cool Output Curve
A nonlinear output curve may improve performance when the response of the output device is nonlinear. If a
cool output uses one of the nonlinear curves a PID calculation yields a lower actual output level than a linear
output would provide.
These output curves are used in plastics extruder applications: curve A for oil-cooled extruders and curve
B for water-cooled extruders.
Select a nonlinear cool output curve with Cool Output Curve [`C;Cr] (Setup Menu, Loop Menu).
Actual Output Power
100
80
60
40
Linear
Curve A
Linear
Curve B
Curve 1
20
Curve 2
0
PID Calculation
Control Methods
Output Configuration
Each controller output can be configured as a heat output, a cool output, an alarm output or deactivated. No
dependency limitations have been placed on the available combinations. The outputs can be configured in any
combination. For instance, all three could be set to cool.
Heat and cool outputs use the set point and Operations parameters to determine the output value. All heat
and cool outputs use the same set point value. Heat and cool each have their own set of control parameters.
All heat outputs use the same set of heat control parameters and all cool outputs use the same set of cool output parameters.
Each alarm output has its own set of configuration parameters and set points, allowing independent operation.
Auto (closed loop) and Manual (open loop) Control
The controller has two basic modes of operation, auto mode and manual mode. Auto mode allows the controller to decide whether to perform closed-loop control or to follow the settings of Input Error Power [FAiL]
(Setup Page, Loop Menu). The manual mode only allows open-loop control. The EZ-ZONE PM controller is
normally used in the auto mode. The manual mode is usually only used for specialty applications or for troubleshooting.
Manual mode is open-loop control that allows the user to directly set the power level to the controller’s output load. No adjustments of the output power level occur based on temperature or set point in this mode.
In auto mode, the controller monitors the input to determine if closed-loop control is possible. The controller checks to make certain a functioning sensor is providing a valid input signal. If a valid input signal is
present, the controller will perform closed-loop control. Closed-loop control uses a process sensor to determine
the difference between the process value and the set point. Then the controller applies power to a control output load to reduce that difference.
If a valid input signal is not present, the controller will indicate an input error message in the upper display and [Attn] in the lower display and respond to the failure according to the setting of Input Error Power
[FAiL]. You can configure the controller to perform a “bumpless” transfer [bPLS], switch power to output a
preset fixed level [MAn], or turn the output power off.
Watlow EZ-ZONE ® PM PID Controller
•
97
•
Chapter 9 Features
Auto (closed loop) and Manual (open loop) Control (cont.)
Power
Temperature
Bumpless transfer will allow the controller to transfer to the manual mode using the last power value calculated in the auto mode if the process had
stabilized at a ±5 percent output power level
for the time interval of Time Integral or 10
Actual Temperature
Set Point
seconds, whichever is longer, (Operations
Page, Loop) prior to sensor failure, and that
Sensor
power level is less than 75 percent.
Break
Input Error Latching [`i;Er] (Setup Page,
Analog Input Menu) determines the control100%
ler’s response once a valid input signal reOutput Power
turns to the controller. If latching is on, then
the controller will continue to indicate an
40%
Locks in
input error until the error is cleared. To clear
2 minutes
Output
a latched alarm, press the Advance Key ‰
Power
0%
then the Up Key ¿.
Time
If latching is off, the controller will autoBumpless Transfer
matically clear the input error and return to
reading the temperature. If the controller was in the auto mode when the input error occurred, it will resume
closed-loop control. If the controller was in manual mode when the error occurred, the controller will remain
in open-loop control.
The Manual Control Indicator Light % is on when the controller is operating in manual mode. You can
easily switch between modes if the Control Mode [`C;M] parameter is selected to appear in the Home Page.
To transfer to manual mode from auto mode, press the Advance Key ‰ until [`C;M] appears in the lower
display. The upper display will display [AUto] for auto mode. Use the Up ¿ or Down ¯ keys to select [Man].
The manual set point value will be recalled from the last manual operation.
To transfer to auto mode from manual mode, press the Advance Key ‰ until [`C;M] appears in the lower
display. The upper display will display [MAn] for manual mode. Use the Up ¿ or Down ¯ keys to select
[AUto]. The automatic set point value will be recalled from the last automatic operation.
Changes take effect after three seconds or immediately upon pressing either the Advance Key ‰ or the
Infinity Key ˆ.
On-Off Control
Temperature
On-off control switches the
output either full on or full
The heating action switches off when the process
off, depending on the input,
temperature rises above the set point.
set point and hysteresis values. The hysteresis value indicates the amount the process
value must deviate from the
Set Point
set point to turn on the output. Increasing the value deHysteresis
creases the number of times
the output will cycle. DecreasProcess Temperature
ing hysteresis improves controllability. With hysteresis
set to 0, the process value
The heating action switches on when the process temperature
would stay closer to the set
drops below the set point minus the hysteresis.
The heating action
point, but the output would
switches on at startup.
switch on and off more frequently, and may result in the
Time
output “chattering.”
On-off control can be selected with Heat Algorithm [`h;Ag] or Cool Algorithm [`C;Ag] (Setup Page, Loop
Menu).
On-off hysteresis can be set with On/Off Heat Hysteresis [`h;hY] or On/Off Cool Hysteresis [`C;hY] (Operations Page, Loop Menu).
Watlow EZ-ZONE ® PM PID Controller
•
98
•
Chapter 9 Features
On-Off Control (cont.)
Note:
Input Error Power Mode
[faIl]
does not function in on-off control mode. The output goes off.
The cooling action switches on when
the process temperature rises above
the set point plus the hysteresis.
Temperature
The cooling action
switches
on at startup.
Process Temperature
Hysteresis
Set Point
The cooling action switches off when the process
temperature drops below the set point.
Time
Proportional Control
Temperature
Some processes need to maintain a temperature or process value closer to the set point than on-off control
can provide. Proportional control provides closer control by adjusting the output when the temperature or
process value is within a proportional band. When the value is in the band, the controller adjusts the output
based on how close the process value is to the set point.
The closer the process value is to the set point, the lower the output power. This is similar to backing off
on the gas pedal of a car as you approach a stop sign. It keeps the temperature or process value from swinging as widely as it would with simple on-off control. However, when the system settles down, the temperature
or process value tends to “droop”
short of the set point.
Overshoot
Set Point
With proportional control the
output power level equals (set
point minus process value) divided
by the proportional band value.
In an application with one
Droop
Proportional Band
output assigned to heating and
another assigned to cooling, each
will have a separate proportional
parameter. The heating parameter takes effect when the process
temperature is lower than the set
point, and the cooling parameter
takes effect when the process temperature is higher than the set
point.
Time
Adjust the proportional band
Proportional Control
with Heat Proportional Band
[`h;Pb] or Cool Proportional Band
[`C;Pb] (Operations Page, Loop Menu).
Watlow EZ-ZONE ® PM PID Controller
•
99
•
Chapter 9 Features
Proportional plus Integral (PI) Control
The droop caused by proportional control can be corrected by adding integral (reset) control. When the system settles down, the integral value is tuned to bring the temperature or process value closer to the set point.
Integral determines the speed of the correction, but this may increase the overshoot at startup or when the
set point is changed. Too much integral action will make the system unstable. Integral is cleared when the
process value is outside of the proportional band.
Adjust the integral with Time Integral [``ti] (Operations Page, Loop Menu).
Proportional plus Integral plus Derivative (PID) Control
Use derivative (rate) control to minimize the overshoot in a PI-controlled system. Derivative (rate) adjusts the
output based on the rate of change in the temperature or process value. Too much derivative (rate) will make
the system sluggish.
Derivative action is active only when the process value is within twice the proportional value from the set
point.
Adjust the derivative with Time Derivative [``td] (Operations Page, Loop Menu).
Set Point
Reduced Overshoot
Proportional Band
Temperature
Proportional Band x 2
Heating Slows
Time
PID Control
Dead Band
In a PID application the dead bands above and below the set point can save an application’s energy and wear
by maintaining process temperature within acceptable ranges.
Proportional action ceases when the process
value is within the dead band. Integral action
continues to bring the process temperature to
the set point.
Cool Output Active
Using a positive dead band value keeps
Set Point
the two systems from fighting each other.
Temperature
Heat Output Active
Positive Dead Band
Time
Watlow
EZ-ZONE ®
PM PID Controller
•
100
•
Chapter 9 Features
Dead Band (cont.)
When the dead band value is zero, the heating output activates when the temperature drops below the
set point, and the cooling output switches on when the temperature exceeds the set point.
Cool Output Active
Set Point
Temperature
Heat Output Active
Zero Dead Band
Time
When the dead band value is a negative value, both heating and cooling outputs are active when the
temperature is near the set point.
Cool Output Active
Set Point
Temperature
Heat Output Active
Negative Dead Band
Time
Adjust the dead band with Dead Band [``db] (Operations Page, Loop Menu).
Variable Time Base
Variable time base is the preferred method for controlling a resistive load, providing a very short time base
for longer heater life. Unlike phase-angle firing, variable-time-base switching does not limit the current and
voltage applied to the heater.
With variable time base outputs, the PID algorithm calculates an output between 0 and 100%, but the
output is distributed in groupings of three ac line cycles. For each group of three ac line cycles, the controller
decides whether the power should be on or off. There is no fixed cycle time since the decision is made for each
group of cycles. When used in conjunction with a zero cross (burst fire) device, such as a solid-state power
controller, switching is done only at the zero cross of the ac line, which helps reduce electrical noise (RFI).
Variable time base should be used with solid-state power controllers, such as a solid-state relay (SSR) or
silicon controlled rectifier (SCR) power controller. Do not use a variable time base output for controlling electromechanical relays, mercury displacement relays, inductive loads or heaters with unusual resistance characteristics.
Watlow EZ-ZONE ® PM PID Controller
•
101
•
Chapter 9 Features
Variable Time Base (cont.)
The combination of variable time base output and a solid-state relay can inexpensively approach the effect
of analog, phase-angle fired control.
50 percent output
100 percent output
3 ON, 3 OFF
10 ON, 0 OFF
Select the AC Line Frequency [AC;LF] (Setup Page, Global Menu), 50 or 60 Hz.
66 percent output
6 ON, 3 OFF
Single Set Point Ramping
Ramping protects materials and systems that cannot tolerate rapid temperature changes. The value of the
ramp rate is the maximum degrees per minute or hour that the system temperature can change.
Select Ramp Action [``rP] (Setup Page, Loop Menu):
[`oFF] ramping not active.
[`Str] ramp at startup.
[StPt] ramp at a set point change.
[both] ramp at startup or when the set point changes.
Select whether the rate is in degrees per minute or degrees per hour with Ramp Scale [`r;SC]. Set the
ramping rate with Ramp Rate [`r;rt] (Setup Page, Loop Menu).
Set Point
Temperature
Temperature
Set Point
degrees
per minute
Temperature reaches Set Point quickly
Temperature ramps to Set Point at a set rate
Time
Time
Heating System without Ramping
Heating System with Ramping
Timer Function
1. When Timer Enable [ti;En] is set to yes [yEs] and the timer is started (you define which key combination this is), the controller will switch from Set Point [C;sp1] to Closed Loop Timer Set Point [Ct;s1]. If
the timer is interrupted, the timer is terminated and the time remaining is reset to its initial value.
2. When Timer Start Method [ti;st] is set to:
a. Immediate [iMd ] , the timer starts as soon as the counter is initiated. When Time Remaining
[t;r1] equals zero, the set point changes from Closed Loop Timer Set Point [Ct;s1] back to Set Point
[C;SP1]. A flashing colon [00; º0] indicates that a countdown is in progress.
Watlow EZ-ZONE ® PM PID Controller
•
102
•
Chapter 9 Features
b. Ready Band [`rdy ] , the set point changes and when the temperature is within ready band, the
ready band indicator ‰ lights up and the countdown timer starts and continues as long as the temperature is within the ready band. When Time Remaining [`t;r1] equals zero, the set point changes
from Closed Loop Timer Set Point [Ct;s1] back to Set Point [C;sp1]. A flashing colon [00; º0] indicates that a countdown is in progress.
c. Ready Acknowledge [rdya] , the set point changes, and when the temperature is within the ready
band, the ready band indicator ‰ lights up. The user must then acknowledge (you define which key
combination for this) that the countdown timer should start and continue as long as the temperature is within the ready band. When Time Remaining [ t;r1] equals zero, the set point changes from
Closed Loop Timer Set Point [Ct;s1] back to Set Point [C;sp1]. A flashing colon [00; º0] indicates
that a countdown is in progress.
d. Power [Pwr] , the timer starts when the controller is turned on. When Time Remaining [`t;r1]
equals zero, the set point changes from Closed Loop Timer Set Point [Ct;s1] back to Set Point
[C;sp1]. A flashing colon [00; º0] indicates that a countdown is in progress.
3. In Setup Page, Output Menu, Output Function [``fn] can be assigned as Timer Event Output 1
[ tE; o1] , Timer Event Output 2 [ tE; o2] or Timer Event Output 3 [ tE; o3] . Timer Event Output 1 is
active during timing, Timer Event Output 2 is deactivated during timing and Timer Event Output 3 is
active at the end of the countdown for a period in seconds specified by Signal Time [~~St] . This signal
may be used to monitor that timing is occurring or signal that timing has completed. Process outputs
may not be assigned to Timer Event Outputs.
4. The home display is customized in the Factory Page, Custom Menu. You may program the display to
alternate between display pairs. See display pairs in the Setup Page, Global Menu. As an example, we
could show the process temperature in the upper display and have the lower display alternate between
the countdown time remaining and the active set point.
Note: The timer feature is only available for control loop 1 of two-loop controllers. Time is entered in hours, minutes and
seconds. Countdown time will use the entered time but display the time remaining in either hh:mm or mm:ss format,
based on your settings. The colon pulses in one-second intervals during a countdown, to indicate that timing is underway. Parameters that appear in the Home page have the number 1 at the end of the displayed parameter. As an example,
[hoUr] in the Setup Page, Timer Menu will be displayed as [hoU1] in the Home Page.
Setting up the timer function
1.Press and hold up ¿ and down ¯ arrow keys for 6 seconds to enter into the Setup Page [`SEt].
2.Up arrow ¿ to Timer Menu [ tMr] .
3.Advance ‰ to Timer Enable [ ti;En] to make selection using the up ¿ and down ¯ arrow keys to select
from the options below:
[`yEs] Yes
[``no] No
4.Advance ‰ to Timer Start Method [ ti;st] to select the method that will start the timer.
5.Use the up arrow ¿ to select from the options below:
[iMd ] Immediate
[`rdy ] Ready Band
[rdya] Ready Ack
[ pWr] Power
6.Advance ‰ to Source Function A [sfn;a] to select which input will start/terminate the timer. Use the up
arrow ¿ to select from the options below:
[nonE] None
[`dio] Digital I/O
[`fUn] Function Key
7.Advance ‰ to Source Instance A and use the up arrow ¿ to make a selection below:
If Source Function A of previous step is set to None [nonE] :
[```1] Does not matter which number is here
[`si;a] Source Instance A
If Source Function A of previous step is set to Digital I/O [`dio] :
[```5] Select 5 to 12
[`si;a] Source Instance A
Watlow EZ-ZONE ® PM PID Controller
•
103
•
Chapter 9 Features
If Source
[```1] [```2]
[```6]
[```7]
[```8]
[`si;a]
Function A of previous step is set to Function Key [`fUn] :
EZ1 Key
EZ2 Key
Hold infinity key for 2 seconds
Infinity ˆ and Down arrow ¯
Infinity ˆ and Up arrow ¿
Source Instance A
8. Advance ‰ to Source Function C [sfn;C] to select the analog source for the ready band. Use the up arrow ¿ to select from the options below:
[``pu] Process Value
[nonE] None
[``ai] Analog Input
[`Lnr] Linearization
9.Advance ‰ and use the up arrow ¿ to make a selection below:
[```1] 1 or ([```2] 2, if second instance of Source Function C)
10.Advance ‰ to Source Function D [sfn;d] to select which input will acknowledge the ready band. Use
the up arrow ¿ to select from the options below:
[nonE] None
[`dio] Digital I/O
[`fUn] Function Key
11.Advance ‰ to Source Instance D and use the up arrow ¿ to make a selection below:
If Source Function D of previous step is set to None [nonE]:
[```1] Does not matter which number is here
[`si;d] Source Instance D
If Source Function D of previous step is set to Digital I/O [`dio]:
[```5] Select 5 to 12
[`si;d] Source Instance D
If Source
[```1] [```2]
[```6]
[```7]
[```8]
[`si;d]
Function D of previous step is set to Function Key [`fUn]:
EZ1 Key
EZ2 Key
Hold infinity key for 2 seconds
Infinity ˆ and Down arrow ¯
Infinity ˆ and Up arrow ¿
Source Instance D
12.Advance ‰ to Time Remaining [``t;r], read only, display in hh:mm or mm:ss.
13.Advance ‰ to Ready Band State [`r;bs], read only, displayed as yes [`yEs] or no [``no].
14.Advance ‰ to Ready Band [`rdy] to enter the value for Ready Band using Up ¿ or Down arrow ¯.
15.Advance ‰ to Time Format [ t;for] to select the time format. Use the up arrow ¿ to make selection below:
[thM] Time Hours:Minutes
[tMs] Time Minutes:Seconds
16.Advance ‰ to Countdown Time to enter hours, minutes and seconds using the Up ¿ or Down arrow ¯.
[hoUr] Hours, then Advance ‰
[Min] Minutes, then Advance ‰
[`SEC] Seconds
17.Advance ‰ to Closed Loop Timer Set Point [Ct;SP] to enter the temperature during counting using the
Up ¿ or Down arrow ¯.
18.Advance ‰ to Signal Time [``st] to enter time in seconds for Timer Event Output 3 [ tE;o3] to be active at end of countdown time.
19. Press and hold the Infinity ˆ or Reset key for more than 2 seconds to go to Home Page.
20. See programming custom home page in factory page, custom menu to change the display parameters
such as active process value, closed loop set point time, closed loop timer set point and time remaining
as appropriate for the application.
Watlow EZ-ZONE ® PM PID Controller
•
104
•
Chapter 9 Features
Alarms
Alarms are activated when the output level, process value or temperature leaves a defined range. A user can
configure how and when an alarm is triggered, what action it takes and whether it turns off automatically
when the alarm condition is over.
Configure alarm outputs in the Setup Page before setting alarm set points.
Alarms do not have to be assigned to an output. Alarms can be monitored and controlled through the
front panel or by using software.
Process and Deviation Alarms
A process alarm uses one or two absolute set points to define an alarm condition.
A deviation alarm uses one or two set points that are defined relative to the control set point. High and
low alarm set points are calculated by adding or subtracting offset values from the control set point. If the set
point changes, the window defined by the alarm set points automatically moves with it.
Select the alarm type with Type [`A;ty] (Setup Page, Alarm Menu).
Alarm Set Points
The High Set Point defines the process value or temperature that will trigger a high side alarm. It must be
higher than the Low Set Point and lower than the high limit of the sensor range.
The Low Set Point defines the temperature that will trigger a low side alarm. It must be lower than the
High Set Point and higher than the low limit of the sensor range.
View or change alarm set points with Low Set Point [`A;Lo] and High Set Point [`A;hi] (Operations Page,
Alarm Menu).
Alarm Hysteresis
High Side Alarm Range
Alarm High Set Point
Alarm Hysteresis
Temperature
An alarm state is triggered when the process value reaches the
alarm high or Low Set Point. Hysteresis defines how far the
process must return into the normal operating range before
the alarm can be cleared.
Hysteresis is a zone inside each alarm set point. This zone
is defined by adding the hysteresis value to the Low Set Point
or subtracting the hysteresis value from the High Set Point.
View or change Hysteresis with Hysteresis [`A;hy] (Setup
Page, Alarm Menu).
Normal Operating Range
Alarm Hysteresis
Low Side Alarm Range
Alarm Low Set Point
Time
Alarm Set Points and Hysteresis
Alarm Latching
Temperature
A latched alarm will remain active after the alarm condition has passed. It can only be deactivated by the user.
The alarm state begins when the temperature
reaches the Alarm High Set Point
An active message, such as an alarm message, will
cause the display to toggle between the normal settings and
Alarm High
the active message in the upper display and [Attn] in the
Set Point
lower display.
Alarm Hysteresis
Push the Advance Key to display [ignr] in the upper
Normal Operating Range
display and the message source in the lower display.
The alarm state continues until the
Use the Up ¿ and Down ¯ keys to scroll through postemperature drops to the Alarm High
Process
sible responses, such as Clear [`CLr] or Silence [`SiL].
Set Point minus the hysteresis. A
Temperature
latching alarm could be turned off by
Then push the Advance ‰ or Infinity ˆ key to execute the
the operator at this point. A
non-latching alarm would turn off
action.
automatically.
See the Keys and Displays chapter and the Home Page
Alarm Low
Set Point
chapter for more details.
Time
An alarm that is not latched (self-clearing) will deactivate automatically when the alarm condition has passed.
Alarm Response with Hysteresis
Turn Latching on or off with Latching [`A;LA] (Setup
Watlow EZ-ZONE ® PM PID Controller
•
105
•
Chapter 9 Features
Page, Alarm Menu).
Alarm Silencing
If Silencing is on the operator can disable the alarm output while the controller is in an alarm state. The process value or temperature has to enter the normal operating range beyond the hysteresis zone to activate the
alarm output function again.
An active message, such as an alarm message, will cause the display to toggle between the normal settings and the active message in the upper display and [Attn] in the lower display.
Push the Advance Key to display [ignr] in the upper display and the message source in the lower display.
Use the Up ¿ and Down ¯ keys to scroll through possible responses, such as Clear [`CLr] or Silence
[`SiL]. Then push the Advance ‰ or Infinity ˆ key to execute the action.
See the Keys and Displays chapter and the Home Page chapter for more details.
Turn Silencing on or off with Silencing [`A;Si] (Setup Page, Alarm Menu).
Alarm Blocking
Blocking allows a system to warm up after it has been started up. With Blocking on, an alarm is not triggered when the process temperature is initially lower than the Low Set Point or higher than the High Set
Point. The process temperature has to enter the normal operating range beyond the hysteresis zone to activate the alarm function.
If the EZ-ZONE PM has an output that is functioning as a deviation alarm, the alarm is blocked when the
set point is changed, until the process value re-enters the normal operating range.
Turn Blocking on or off with Blocking [`A;bL] (Setup Page, Alarm Menu).
Open Loop Detection
When Open Loop Detection is enabled [`l; d e] , the controller will look for the power output to be at 100%.
Once there, the control will then begin to monitor the Open Loop Detect Deviation [`l; d d ] as it relates to
the value entered for the Open Loop Detect Time [`l; d t] . If the specified time period expires and the deviation does not occur, an Open Loop Error will be triggered. Once the Open Loop Error condition exists the control mode will go off.
Note:
All prompts identified in this section can be found in the Loop Menu of the Setup Page.
Programming the EZ Key/s
You can program the EZ Key either in the Setup Menu or with configuration software, such as EZ-ZONE
Configurator, using a personal computer.
The following examples show how to program the EZ Key to start and stop a profile.
Using keys and display:
1. To go to the Setup Page from the Home Page, press both the Up ¿ and Down ¯ keys for six seconds. [``Ai]
will appear in the upper display and [`Set] will appear in the lower display.
2. Press the Up Key ¿ until [`Fun] appears in the upper display and [`SEt] will appear in the lower display.
3. Press the Advance Key ‰ until Digital Input Level [`leu] appears in the lower display. Use an arrow key
to specify the state of the key (high or low) when the controller is powered up. Functions will toggle with each
press of the EZ Key, such as Profile Start/Stop.
4. Press the Advance Key ‰. The lower display will show Digital Function [``Fn]. Press the Up ¿ or
Down ¯ key to scroll through the functions that can be assigned to the EZ Key
When Profile Start/Stop [P;StS] appears in the upper display and [``Fn] appears in the lower display,
press the Advance Key ‰ once to select that function and move to the Function Instance [``FS] parameter.
5. Press the Up ¿ or Down ¯ key to scroll to the profile that you want the EZ Key to control.
6. The instance tells the controller which of the numbered functions should be acted upon. For profiles,
there are 4 instances. Press the Infinity Key ˆ once to return to the submenu, twice to return to the
main menu or three times to return to the Home Page.
Watlow EZ-ZONE ® PM PID Controller
•
106
•
Chapter 9 Features
Using Lockout and Password Security
If unintentional changes to parameter settings might raise safety concerns or lead to downtime, you can use
the lockout feature to make them more secure. There are two methods of lockout that can be deployed, both of
which are accessible from the Factory Page.
Method 1-Change the value of the Read Lock [rloc] (1 to 5) and Set Lock [sloc] (0 to 5) prompts where
the higher the value or setting for each translates to a higher security clearance (greater access).
Method 2-Enable Password Security [ pas ; e ] and then modify the Lock Level [loC; l] value which ranges
from 1 to 5. See the section entitled Using Lockout Method 2 for more detail.
Using Lockout Method 1 (Read and Set Lock)
All Pages have security levels assigned where two of those cannot be changed (Home and Setup). Defaults
(factory settings) for each are shown below:
- Home Page = 1
- Operations Page = 2 (changeable to 1, 2 or 3)
- Setup Page = 4
- Profiling Page = 3 (changeable to 1, 2 or 3)
- Factory Page = 5*
*The Factory Page is always visible where all menus within it may or may not be visible/writable. For further
detail see table "Factory Page Menus".
The table below represents the various levels of lockout for the Set Lockout Security prompt [SLoC] and
the Read Lockout Security prompt [rLoC]. Looking at the table, "Y" equates to yes (can write/read) where
"N" equates to no (cannot write/read). The colored cells simply differentiate one level from the next while also
showing the level where read/write is enabled. As stated previously, the Set Lockout has 6 levels (0 to 5) of security where the Read Lockout has 5 (1 to 5). Therefore, level "0" applies to Set Lockout only.
Lockout Security [SLoC] & [rloC]
Security Level
Pages
0 1 2 3 4 5
Home Page (cannot be
N Y Y Y Y Y
changed)
Operations Page
N
N
Y
Y
Y
Y
Setup Page (cannot
be changed)
N
N
N
N
Y
Y
Profile Page
N
N
N
Y
Y
Y
Factory Page
Y
Y
Y
Y
Y
Y
Being able to change the page security level for the Operations and Profile pages allows a user to give access
to the Profile Page while locking out the Operations Page. The following example shows how the Lockout feature may be used to accomplish this:
1. Press and hold the Advance ‰ and Infinity ˆ keys for approximately 6 seconds to enter the Factory Page
2. Navigate to the [`LoC] Menu using the Up or Down arrow keys
3. Using the green Advance key navigate to the Lock Operations prompt [LoC;o] and change it (push the Up
arrow) from the default value of 2 to 3
4. Push the Advance key again and change the Lock Profiling prompt [LoC;P] from the default of 3 to 2
5. Change Read Lockout Security [rLoC] to 2 and the Set Lockout [SLoC] to 2 or higher
With the above settings, the Home Page and the Profiling Page can be accessed, and all writable parameters can be written to. Due to the Read lock setting of 2 all pages with security levels greater than 2 will be
locked out (inaccessible).
Another example of Method 1 lockout usage could be that an operator wants read access to all pages while allowing read/write access to the Home Page and the Lockout Menu only.
1. Press and hold the Advance and Infinity keys for approximately 6 seconds to enter the Factory Page
2. Navigate to the [`LoC] Menu using the Up or Down arrow keys
3. Using the green Advance key navigate to the Read Lockout Security [rLoC] and change it to 5
4. Push the green Advance key and navigate to the and Set Lockout Security [SLoC] changing it to 1
Although the Factory Page is always visible, some menus within it can be restricted.
Watlow EZ-ZONE ® PM PID Controller
•
107
•
Chapter 9 Features
Lockout Security [SLoC] & [rloC]
Factory Page Menus
Security Level
Menus
0 1 2 3 4 5
Custom Menu
N N N N N Y
Lockout Menu*
Y
Y
Y
Y
Y
Y
Diagnostic Menu**
N
Y
Y
Y
Y
Y
Calibration Menu
N
N
N
N
N
Y
*Using lockout Method 1 with [SLoC] set to 0, all writable parameters within the control will be inhibited
(not writable) with two exceptions, [sloC] and [rloC] . As shown below, both of these parameters can always be seen and modified.
** Diagnostic Menu and all associated prompts are always visible and never writable
Lockout Security [SLoC] & [rloC]
Factory Page Menu Parameters
Security Level
Parameters
0 1 2 3 4 5
N Y Y Y Y Y
[LoC;O]
[loC; p ]
N
Y
Y
Y
Y
Y
[ pas ; e ]
N
Y
Y
Y
Y
Y
[rloC]
Y
Y
Y
Y
Y
Y
[sloC]
Y
Y
Y
Y
Y
Y
Note:
Using Method 1 Lockout all settings can be modified by anyone who knows how to find their way to the
[SLoC] and [rloC] parameters
Using Lockout Method 2 (Password Enable)
It is sometimes desirable to apply a higher level of security to the control where a password would be required
to access the control. If Password Enabled [ pas ; e ] in the Factory Page under the [`loC] Menu is set to on,
an overriding Password Security will be in effect. Without the appropriate password, specified menus will remain inaccessible. Page and Menu access is defined in the Locked Access Level [loC;L] prompt. On the other
hand, a User with a password would have visibility restricted by the Read Lockout Security [rloC] . As an
example, with Password Enabled and the Locked Access Level [loC;L] set to 1 and [rloC] is set to 3, the
available Pages for a User without a password would be limited to the Home and Factory Pages (locked level
1). If the User password is entered all pages would be accessible with the exception of the Setup Page as defined by level 3 access.
How to Enable Password Security
Follow the steps below:
1. Go to the Factory Page by holding down the Infinity ˆ key and the Advance ‰ key for approximately six
seconds.
2. Push the Down ¯ key one time to get to the [`loC] menu. Again push the Advance ‰ key until the Password Enabled [ pas ; e ] prompt is visible.
3. Push either the up or down key to turn it on. Once on, 4 new prompts will appear:
1. [loC; l] , Locked Access Level (1 to 5) corresponding to the lockout table above.
2. [roll] , Rolling Password will change the Customer Code every time power is cycled.
3. [ pas ; u ] , User Password which is needed for a User to acquire access to the control.
4. [ pas ; a ] , Administrator Password which is needed to acquire administrative access to the control.
The Administrator can either change the User and or the Administrator password or leave them in the default state. Once Password Security is enabled they will no longer be visible to anyone other than the Administrator. In other words the Lock Menu [`loC] is not available to a User. As can be seen in the formula that
follows either the User or Administrator will need to know what those passwords are to acquire a higher level
Watlow EZ-ZONE ® PM PID Controller
•
108
•
Chapter 9 Features
of access to the control. Back out of this menu by pushing the Infinity ˆ key. Once out of the menu, the Password Security will be enabled.
How to Acquire Access to the Control
To acquire access to any inaccessible Pages or Menus, go to the Factory Page and enter the [UloC] menu.
Once there follow the steps below:
Note:
If Password Security (Password Enabled [pas;e] is On) is enabled the two prompts mentioned below in
the first step will not be visible. If the password is unknown, call the individual or company that originally
setup the control.
1. Acquire either the User Password [ pas ; u ] or the Administrator Password [ pas ; a ] .
2. Push the Advance ‰ key one time where the Code [Cod e] prompt will be visible.
Note:
a.If the the Rolling Password is off push the Advance key one more time where the Password [ pass]
prompt will be displayed. Proceed to either step 7a or 8a. Pushing the Up ¿ or Down ¯ arrow keys enter
either the User or Administrator Password. Once entered, push and hold the Infinity ˆ key for two seconds
to return to the Home Page.
b.If the Rolling Password [roll] was turned on proceed on through steps 3 - 9.
3. Assuming the Code [Cod e] prompt (Public Key) is still visible on the face of the control simply push the
Advance key ‰ to proceed to the Password [ pass] prompt. If not find your way back to the Factory Page
as described above.
4. Execute the calculation defined below (7b or 8b) for either the User or Administrator.
5. Enter the result of the calculation in the upper display play by using the Up ¿ and Down ¯ arrow keys or
use EZ-ZONE Confgurator Software.
6. Exit the Factory Page by pushing and holding the Infinity ˆ key for two seconds.
Formulas used by the User and the Administrator to calculate the Password follows:
Passwords equal:
7.User
a. If Rolling Password [roll] is Off, Password [ pass] equals User Password [ pas ; u ] .
b.If Rolling Password [roll] is On, Password [ pass] equals: ([ pas ; u ] x code) Mod 929 + 70
8. Administrator
a. If Rolling Password [roll] is Off, Password [ pass] equals User Password [ pas ; a ] .
b.If Rolling Password [roll] is On, Password [ pass] equals: ([ pas ; a ] x code) Mod 997 + 1000
Differences Between a User Without Password,
User With Password and Administrator
-User without a password is restricted by the Locked Access Level [loC; l] .
- A User with a password is restricted by the Read Lockout Security [rloC] never having access to the
Lock Menu [`loC] .
- An Administrator is restricted according to the Read Lockout Security [rloC] however, the Administrator has access to the Lock Menu where the Read Lockout can be changed.
Modbus - Using Programmable Memory Blocks
When using the Modbus protocol, the PM control features a block of addresses that can be configured by the
user to provide direct access to a list of 40 user configured parameters. This allows the user easy access to
this customized list by reading from or writing to a contiguous block of registers.
To acquire a better understanding of the tables found in the back of this document (See Appendix: (Modbus Programmable Memory Blocks) please read through the text below which defines the column headers
used.
Watlow EZ-ZONE ® PM PID Controller
•
109
•
Chapter 9 Features
Assembly Definition Addresses
- Fixed addresses used to define the parameter that will be stored in the "Working Addresses", which may
also be referred to as a pointer. The value stored in these addresses will reflect (point to) the Modbus address of a parameter within the PM controller.
Assembly Working Addresses
- Fixed addresses directly related to their associated "Assembly Definition Addresses" (i.e., Assembly
Working Addresses 200 & 201 will assume the parameter pointed to by Assembly Definition Addresses
40 & 41).
When the Modbus address of a target parameter is stored in an "Assembly Definition Address" its corresponding working address will return that parameter’s actual value. If it’s a writable parameter, writing to
its working register will change the parameter’s actual value.
As an example, Modbus register 360 contains the Analog Input 1 Process Value (See Operations Page,
Analog Input Menu). If the value 360 is loaded into Assembly Definition Address 91, the process value sensed
by analog input 1 will also be stored in Modbus registers 250 and 251. Note that by default this parameter is
also stored in working registers 240 and 241 as well.
The table (See Appendix: Modbus Programmable Memory Blocks) identified as "Assembly Definition Addresses and Assembly Working Addresses" reflects the assemblies and their associated addresses.
Software Configuration
Using EZ-ZONE® Configurator Software
To enable a user to configure the PM control
using a personal computer (PC), Watlow has
provided free software for your use. If you
have not yet obtained a copy of this software
insert the CD (Controller Support Tools) into
your CD drive and install the software. Alternatively, if you are viewing this document
electronically and have a connection to the
internet simply click on the link below and
download the software from the Watlow web
site free of charge.
http://www.watlow.com/products/software/zone_
config.cfm
Once the software is installed double click on
the EZ-ZONE Configurator icon placed on
your desktop during the installation process.
If you cannot find the icon follow the steps
below to run the software:
1. Move your mouse to the "Start" button
2. Place the mouse over "All Programs"
3. Navigate to the "Watlow" folder and then the subfolder "EZ-ZONE Configurator"
4.Click on EZ-ZONE Configurator to run.
The first screen that will appear is shown on the right.If the PC is already physically connected to the EZZONE PM control click the next button to go on-line.
Note:
When establishing communications from PC to the EZ-ZONE PM control an interface converter will be required. The Standard Bus network uses EIA-485 as the interface. Most PCs today would require a USB to
EIA-485 converter. However, some PCs may still be equipped with EIA-232 ports, therefore an EIA-232 to
EIA-485 converter would be required.
As can be seen in the above screen shot the software provides the user with the option of downloading a previously saved configuration as well as the ability to create a configuration off-line to download later. The
screen shots that follow will take the user on-line.
After clicking the next button above it is necessary to define the communications port that will be used on
the PC as shown below. Clicking on the drop down will allow the user to select the appropriate communications port. This will be the port assigned to the EIA-485 to USB converter when it was connected to the PC.
Watlow EZ-ZONE ® PM PID Controller
•
110
•
Chapter 9 Features
The "Advanced" button allows the user to determine
how many devices to look for on the network (1 to 17).
After clicking on the "Next" button, the software will
scan the network for the zone addresses specified
while showing the progress made (as shown in the
graphic below. When complete the software will display all of the available devices found on the network
as shown below.
The PM8 is shown highlighted to bring greater clarity to the control in focus. Any EZ-ZONE device on
the network will appear in this window and would be
available for the purpose of configuration or monitoring; simply click on the control of choice. After doing
so, the screen below will appear. In the screen shot
below notice that the device part number is clearly displayed at the top of the page (yellow highlight added
for emphasis). When multiple EZ-ZONE devices are on
the network it is important that the part number be noted prior to configuring so as to avoid making unwanted configuration changes to another control. Looking closely at
the left hand column (Parameter Menus) notice that it displays all of the available menus and associated parameters within the control. The menu structure as laid out within this software follows:
- Setup - Operations - Factory - Profile
Searching Network for Devices
Available Network Devices Displayed
Navigating from one menu to the next is easy and clearly visible. Simply slide the scroll bar up or down to display the menu and parameter of choice. If there is a need to bring greater focus and clarity to the parameters
of interest simply click on the negative symbol next to any of the Menu items. As an example if it is desired
to work within the Operations page click the negative sign next to Setup where the Setup Page will then collapse. Now click the plus sign next to Operations to find the menu items of choice without viewing unwanted
menus and parameters. Once the focus is brought to an individual parameter (single click of mouse) as is the
case for Analog Input 1 in the left column; all that can be setup related to that parameter will appear in the
center column. The grayed out fields in the center column simply mean that this does not apply for the type
of sensor selected. As an example, notice that when a thermocouple is selected, RTD Leads does not apply
and is therefore grayed out. To speed up the process of configuration notice that at the bottom of the center
column there is an option to copy settings. If Analog Input 1 and 2 are the same type of sensor click on "Copy
Settings" where a copy dialog box will appear allowing for quick duplication of all settings. Notice too, that by
clicking on any of those items in the center column that context sensitive help will appear for that particular
item in the right hand column.
Lastly, when the configuration is complete click the "Finish" button at the bottom right of the previous
screen shot. The screen that follows this action can be seen below.
Watlow EZ-ZONE ® PM PID Controller
•
111
•
Chapter 9 Features
Although the PM control now contains the configuration (because the previous discussion focused on doing
the configuration on-line) it is suggested that after the configuration process is completed that the user save
this file on the PC for future use. If for some reason someone inadvertently changed a setting without understanding the impact, it would be easy and perhaps faster to download a saved configuration back to the
control versus trying to figure out what was changed. Of course, there is an option to exit without saving a
copy to the local hard drive. After selecting Save above, click the "Finish" button once again. The screen below will than appear. When saving the configuration, note the location where the file will be placed (saved
in) and enter the file name (File name) as well. The default path for saved files follows: Users\"Username"\
My Documents\Watlow\EZ-Zone Configurator\Saved Configurations
The user can save the file to any folder of choice.
Watlow EZ-ZONE ® PM PID Controller
•
112
•
Chapter 9 Features
Chapter 10: Appendix
Troubleshooting Alarms, Errors and Control Issues
Indication
Description
Possible Causes
Alarm won’t clear or reset
Alarm will not clear or reset
with keypad or digital input
• Latching is active
Alarm won’t occur
Alarm will not activate output
• Silencing is active
• Blocking is active
• Alarm is set to incorrect output
• Alarm is set to incorrect
source
• Alarm set point is incorrect
Corrective Action
• Reset alarm when process is
within range or disable latching
• Alarm set to incorrect output • Set output to correct alarm
source instance
• Alarm is set to incorrect
• Set alarm source to correct insource
put instance
• Sensor input is out of alarm
• Correct cause of sensor input
set point range
out of alarm range
• Alarm set point is incorrect
• Set alarm set point to correct
trip point
• Alarm is set to incorrect type • Set alarm to correct type: process, deviation or power
• Digital input function is incor- • Set digital input function and
rect
source instance
• Alarm is set to incorrect type
• Disable Silencing, if required
• Disable Blocking, if required
• Set output to correct alarm
source instance
• Set alarm source to correct input instance
• Set alarm set point to correct
trip point
• Set alarm to correct type: process, deviation or power
[AL;E1] Alarm Error
[AL;E2]
[AL;E3]
[AL;E4]
Alarm state cannot be determined due to lack of sensor
input
• Sensor improperly wired or open • Correct wiring or replace sensor
• Incorrect setting of sensor type • Match setting to sensor used
• Calibration corrupt
• Check calibration of controller
[AL;L1] Alarm Low
[AL;L2]
[AL;L3]
[AL;L4]
Sensor input below low alarm
set point
• Temperature is less than
• Check cause of under temperaalarm set point
ture
• Alarm is set to latching and an • Clear latched alarm
alarm occurred in the past
• Incorrect alarm set point
• Establish correct alarm set
point
• Incorrect alarm source
• Set alarm source to proper setting
[AL;h1} Alarm High
[AL;h2]
[AL;h3]
[AL;h4]
Sensor input above high alarm
set point
• Temperature is greater than
• Check cause of over temperaalarm set point
ture
• Alarm is set to latching and an • Clear latched alarm
alarm occurred in the past
• Incorrect alarm set point
• Establish correct alarm set
point
• Incorrect alarm source
• Set alarm source to proper setting
[Er;i1] Error Input
Sensor does not provide a valid
signal to controller
• Sensor improperly wired or open • Correct wiring or replace sensor
• Incorrect setting of sensor type • Match setting to sensor used
• Calibration corrupt
• Check calibration of controller
[Er;Ab] Ambient Error
Cold-junction compensation circuitry is not working.
• Cold-junction compensation
circuitry is not working.
Watlow EZ-ZONE ® PM PID Controller
•
113
•
• Return controller to factory.
Appendix
Troubleshooting Alarms, Errors and Control Issues (cont.)
Indication
Description
Possible Causes
[LP;o1] Loop Open Error
Open Loop Detect is active and
the process value did not deviate by a user-selected value in
a user specified period.
• Setting of Open Loop Detect
Time incorrect
• Setting of Open Loop Detect
Deviation incorrect
• Thermal loop is open
[LP;r1] Loop Reversed Error
Open Loop Detect is active and
the process value is headed
in the wrong direction when
the output is activated based
on deviation value and userselected value.
• Setting of Open Loop Detect
Time incorrect
• Setting of Open Loop Detect
Deviation incorrect
• Output programmed for incorrect function
• Thermocouple sensor wired in
reverse polarity
Corrective Action
• Set correct Open Loop Detect
Time for application
• Set correct Open Loop Deviation value for application
• Determine cause of open thermal loop: misplaced sensors, load
failure, loss of power to load, etc.
• Open Loop Detect function not • Deactivate Open Loop Detect
required but activated
feature
• Set correct Open Loop Detect
Time for application
• Set correct Open Loop Deviation value for application
• Set output function correctly
• Wire thermocouple correctly,
(red wire is negative)
[`rP1] Ramping 1
Controller is ramping to new set • Ramping feature is activated
point
• Disable ramping feature if not
required
[tUN1] Autotuning 1
Controller is autotuning the con- • User started the autotune
trol loop
function
• Digital input is set to start
autotune
• Wait until autotune completes
or disable autotune feature
• Set digital input to function
other than autotune, if desired
No heat/cool action
Output does not activate load
• Output function is incorrectly set • Set output function correctly
• Control mode is incorrectly set • Set control mode appropriately
(Open vs Closed Loop)
• Correct output wiring
• Output is incorrectly wired
• Correct fault in system
• Load, power or fuse is open
• Set control set point in appro• Control set point is incorrect
priate control mode and check
source of set point: remote, idle,
profile, closed loop, open loop
• Incorrect controller model for • Obtain correct controller model
for application
application
No Display
No display indication or LED illumination
•
•
•
•
•
No Serial Communication
Cannot establish serial communications with the controller
Power to controller is off
Fuse open
Breaker tripped
Safety interlock switch open
Separate system limit control
activated
• Wiring error
• Incorrect voltage to controller
• Turn on power
• Replace fuse
• Reset breaker
• Close interlock switch
• Reset limit
• Address parameter incorrect
• Incorrect protocol selected
• Baud rate incorrect
• Parity incorrect
• Wiring error
• EIA-485 converter issue
• Set unique addresses on network
• Match protocol between devices
• Match baud rate between devices
• Match parity between devices
• Correct wiring issue
• Check settings or replace converter
• Set correct communication port
• Incorrect computer or PLC
communications port
• Incorrect software setup
• Termination resistor may be
required
Watlow EZ-ZONE ® PM PID Controller
•
114
•
• Correct wiring issue
• Apply correct voltage, check
part number
• Correct software setup to match
controller
• Place 120 Ω resistor across
EIA-485 on last controller
Appendix
Troubleshooting Alarms, Errors and Control Issues (cont.)
Indication
Description
Possible Causes
Process doesn’t control to set
point
Process is unstable or never
reaches set point
• Controller not tuned correctly
Temperature runway
Process value continues to increase or decrease past set
point.
• Controller output incorrectly
programmed
• Thermocouple reverse wired
Corrective Action
• Perform autotune or manually
tune system
• Control mode is incorrectly set • Set control mode appropriately
(Open vs Closed Loop)
• Control set point is incorrect
• Set control set point in appropriate control mode and check
source of set point: remote, idle,
profile, closed loop, open loop
• Verify output function is correct
(heat or cool)
• Correct sensor wiring (red wire
negative)
• Verify and correct wiring
• Controller output wired incorrectly
• Short in heater
• Replace heater
• Power controller connection to • Replace or repair power concontroller defective
troller
• Controller output defective
• Replace or repair controller
[`100] Device Error
[rEtn]
Controller displays internal mal- • Controller defective
function message at power up.
• Replace or repair controller
Menus inaccessible
Unable to access [`SEt], [OP- • Security set to incorrect level
Er], [FCty] or [ProF] menus
or particular prompts in Home • Digital input set to lockout
Page
keypad
• Custom parameters incorrect
• Check lockout setting in Factory Page
• Change state of digital input
EZ-Key does not activate required function
• Verify EZ-Key function in Setup
Menu
• Check that the function instance is correct
• Replace or repair controller
EZ-Key doesn’t work
• EZ-Key function incorrect
• EZ-Key function instance not
incorrect
• Keypad malfunction
Watlow EZ-ZONE ® PM PID Controller
•
115
•
• Change custom parameters in
Factory Page
Appendix
Troubleshooting Alarms, Errors and Control Issues (cont.)
Detection of and Rules Around Abnormal Sensor Conditions
Inputs
Detection of Abnormal Conditions
Thermocouple
Shorted
No direct detection, Open loop firmware detection.
Open
Yes, Parasitic pull-up
Reversed
Yes, firmware detection
Current Source
Shorted
Range limiting only
Open
Range limiting only
Reversed
Range limiting only
Voltage Source
Open
Range limiting only
Shorted
Range limiting only
Reversed
Range limiting only
RTD
S1 open
Yes, pulled up.
S2 open
Not implemented.
S3 open
Yes, pulled up.
S1 short to S2
Yes, pulled up
S1 short to S3
Yes, pulled down to under range.
S2 shorted to S3
Not implemented, Possible, monitor S2 voltage.
S1 and S2 open
Yes, pulled down to under range.
S1 and S3 open
Yes, S1 pulled up.
S2 and S3 open
Yes pulled up.
Thermistor
S1 open
Yes, pulled up to sensor over range.
S3 open
Yes, pulled up to sensor over range.
S1 short to S3
Yes, pulled down to sensor under range.
S1 and S3 open
Yes, S1 pulled up to sensor over range.
Watlow EZ-ZONE ® PM PID Controller
•
116
•
Appendix
Modbus - Programmable Memory Blocks
Assembly Definition Addresses and Assembly Working Addresses
Assembly Definition
Addresses
40 & 41
42 & 43
44 & 45
46 & 47
48 & 49
50 & 51
52 & 53
54 & 55
56 & 57
58 & 59
60 & 61
62 & 63
64 & 65
66 & 67
68 & 69
70 & 71
72 & 73
74 & 75
76 & 77
78 & 79
Assembly Working
Addresses
200 & 201
202 & 203
204 & 205
206 & 207
208 & 209
210 & 211
212 & 213
214 & 215
216 & 217
218 & 219
220 & 221
222 & 223
224 & 225
226 & 227
228 & 229
230 & 231
232 & 233
234 & 235
236 & 237
238 & 239
Assembly Definition
Addresses
80 & 81
82 & 83
84 & 85
86 & 87
88 & 89
90 & 91
92 & 93
94 & 95
96 & 97
98 & 99
100 & 101
102 & 103
104 & 105
106 & 107
108 & 109
110 & 111
112 & 113
114 & 115
116 & 117
118 & 119
Assembly Working
Addresses
240 & 241
242 & 243
244 & 245
246 & 247
248 & 249
250 & 251
252 & 253
254 & 255
256 & 257
256 & 259
260 & 261
262 & 263
264 & 265
266 & 267
268 & 269
270 & 271
272 & 273
274 & 275
276 & 277
278 & 279
Assembly Definition
Addresses
Default Pointers
Assembly Working
Addresses
Assembly Definition
Addresses
Default Pointers
Assembly Working
Addresses
Registers 40 & 41
Registers 200 & 201
Registers 60 & 61
Registers 220 & 221
Pointer 1 = 1880 & 1881
Loop Control Mode
Registers 42 & 43
Pointer 2 = 2160 & 2161
Closed Loop Set Point
Registers 44 & 45
Pointer 3 = 2162 & 2163
Open Loop Set Point
Registers 46 & 47
Pointer 4 = 1480 & 1481
Alarm 1 High Set Point
Registers 48 & 49
Pointer 5 = 1482 & 1483
Alarm 1 Low Set Point
Registers 50 & 51
Pointer 6 = 1530 & 1531
Alarm 2 High Set Point
Registers 52 & 53
Pointer 7 = 1532 & 1533
Alarm 2 Low Set Point
Registers 54 & 55
Pointer 8 = 1580 & 1581
Alarm 3 High Set Point
Registers 56 & 57
Pointer 9 = 1582 & 1583
Alarm 3 Low Set Point
Registers 58 & 59
Pointer 10 = 1630 & 1631
Alarm 4 High Set Point
Pointer 11 = 1632 & 1633
Alarm 4 Low Set Point
Value of Pointer 1
Registers 62 & 63
Registers 202 & 203
Pointer 12 = 2540 & 2541
Profile Action Request
Value of Pointer 2
Registers 64 & 65
Registers 204 & 205
Pointer 13 = 2520 & 2521
Profile Start
Value of Pointer 3
Registers 66 & 67
Registers 206 & 207
Pointer 14 = 1890 & 1891
Heat Proportional Band
Value of Pointer 4
Registers 68 & 69
Registers 208 & 209
Pointer 15 = 1892 & 1893
Cool Proportional Band
Value of Pointer 5
Registers 70 & 71
Registers 210 & 211
Pointer 16 = 1894 & 1895
Time Integral
Value of Pointer 6
Registers 72 & 73
Registers 212 & 213
Pointer 17 = 1896 & 1897
Time Derivative
Value of Pointer 7
Registers 74 & 75
Registers 214 & 215
Pointer 18 = 1900 & 1901
Heat Hysteresis
Value of Pointer 8
Registers 76 & 77
Registers 216 & 217
Pointer 19 = 1902 & 1903
Cool Hysteresis
Value of Pointer 9
Registers 78 & 79
Registers 218 & 219
Pointer 20 = 1898 & 1899
Deadband
Value of Pointer 10
Watlow EZ-ZONE ® PM PID Controller
•
117
•
Value of Pointer 11
Registers 222 & 223
Value of Pointer 12
Registers 224 & 225
Value of Pointer 13
Registers 226 & 227
Value of Pointer 14
Registers 228 & 229
Value of Pointer 15
Registers 230 & 231
Value of Pointer 16
Registers 232 & 233
Value of Pointer 17
Registers 234 & 235
Value of Pointer 18
Registers 236 & 237
Value of Pointer 19
Registers 238 & 239
Value of Pointer 20
Appendix
Modbus Default Assembly Structure 80-119
Assembly Definition
Addresses
Default Pointers
Assembly Working
Addresses
Assembly Definition
Registers
Default Pointers
Assembly Working
Registers
Registers 80 & 81
Registers 240 & 241
Registers 100 & 101
Registers 260 & 261
Pointer 21 = 360 & 361
Analog Input 1 Process
Value
Registers 82 & 83
Pointer 22 = 362 & 363
Analog Input 1 Error Status
Registers 84 & 85
Pointer 23 = 440 & 441
Analog Input 2 Process
Value
Registers 86 & 87
Pointer 24 = 442 & 443
Analog Input 2 Error Status
Pointer 31 = 1882 & 1883
Control Mode Active
Value of Pointer 21
Registers 102 & 103
Registers 242 & 243
Pointer 32 = 1904 & 1905
Heat Power
Value of Pointer 22
Registers 104 & 105
Registers 244 & 245
Pointer 33 = 1906 & 1907
Cool Power
Value of Pointer 23
Registers 106 & 107
Registers 246 & 247
Pointer 34 = 690 & 691
Limit State
Value of Pointer 24
Registers 108 & 109
Registers 88 & 89
Pointer 25 = 1496 & 1497
Alarm 1 State
Registers 248 & 249
Pointer 35 = 2520 & 2521
Profile Start
Value of Pointer 25
Registers 110 & 111
Registers 90 & 91
Pointer 26 = 1546 & 1547
Alarm 2 State
Registers 92 & 93
Pointer 27 = 1596 & 1597
Alarm 3 State
Pointer 36 = 2540 & 2541
Profile Action Request
Registers 250 & 251
Pointer 28 = 1646 & 1647
Alarm 4 State
Registers 112 & 113
Pointer 37 = 2524 & 2525
Active File
Registers 252 & 253
Pointer 29 = 1328 & 1329
Digital Input 5 Status
Registers 98 & 99
Pointer 30 = 1348 & 1349
Digital Input 6 Status
Value of Pointer 32
Registers 264 & 265
Value of Pointer 33
Registers 266 & 267
Value of Pointer 34
Registers 268 & 269
Value of Pointer 35
Registers 270 & 271
Value of Pointer 36
Registers 272 & 273
Value of Pointer 37
Value of Pointer 27
Pointer 38 = 2526 & 2527
Active Step
Registers 254 & 256
Registers 274 & 275
Value of Pointer 38
Value of Pointer 28
Registers 116 & 117
Registers 96 & 97
Registers 262 & 263
Value of Pointer 26
Registers 114 & 115
Registers 94 & 95
Value of Pointer 31
Pointer 39 = 2528 & 2529
Active Set Point
Registers 256 & 257
Registers 276 & 277
Value of Pointer 39
Value of Pointer 29
Registers 118 & 119
Pointer 40 = 2536 & 2537
Step Time Remaining
Registers 258 & 259
Registers 278 & 279
Value of Pointer 40
Value of Pointer 30
Watlow EZ-ZONE ® PM PID Controller
•
118
•
Appendix
Specifications
LineVoltage/Power (Minimum /Maximum Ratings)
•85 to 264V~ (ac), 47 to 63Hz
•20 to 28VÅ (ac), 47 to 63Hz
•12 to 40VÎ (dc)
•14VA maximum power consumption (PM4, 8 & 9)
•10VAmaximum power consumption (PM3 & 6)
•Data retention upon power failure via nonvolatile memory
•Compliant with SEMIF47-0200, FigureR1-1 voltage sag requirements @24V ~ (ac) or higher
Environment
Voltage Input Ranges
- Accuracy ±10mV ±1 LSD at standard conditions
- Temperature stability ±100 PPM/°C maximum
Milliamp Input Ranges
- Accuracy ±20µA ±1 LSD at standard conditions
- Temperature stability ±100 PPM/°C maximum
Resolution Input Ranges
- 0 to 10V: 200 µV nominal
- 0 to 20 mA: 0.5 mA nominal
•Potentiometer: 0 to 1,200Ω
•Inverse scaling
•0 to 149°F (-18 to 65°C) operating temperature
•-40 to 185°F (-40 to 85°C) storage temperature
•0 to 90%RH, non-condensing
Input Type
Accuracy
•Calibration accuracy and sensor conformity: ±0.1% of span, ±1°C
@ the calibrated ambient temperature and rated line voltage
•Types R, S, B; 0.2%
•Type T below -50°C; 0.2%
•Calibration ambient temperature @ 77 ±5°F (25±3°C)
•Accuracy span :1000 °F (540°C) min.
•Temperature stability: ±0.1 °F/°F (±0.1 °C/°C) rise in ambient
maximum
±1.75
0
750
Deg C
±2.45
-200
1250
Deg C
T (-200 to 350)
±1.55
0
350
Deg C
N
±2.25
0
1250
Deg C
E
±2.10
-200
900
Deg C
R
±3.9
0
1450
Deg C
S
±3.9
0
1450
Deg C
B
±2.66
870
1700
Deg C
C
±3.32
0
2315
Deg C
D
±3.32
0
2315
Deg C
F (PTII)
±2.34
0
1343
Deg C
RTD, 100 ohm
±2.00
-200
800
Deg C
±2.00
-200
800
DegC
mV
±0.05
0
50
mV
Volts
±0.01
0
10
Volts
mAdc
±0.02
0
20
mAmps
DC
mAac
±5
-50
50
mAmps
AC
Potentiometer,
1K range
±1
0
1000
Ohms
Thermistor, 5K
range
±5
0
5000
Ohms
Thermistor,
10K range
±10
0
10000
Ohms
Thermistor,
Thermistor
±20
0
20000
Ohms
Thermistor,
40K range
±40
0
40000
Ohms
Isolated Serial Communications
•EIA232/485, Modbus® RTU
Wiring Termination—Touch-Safe Terminals
Operating Range
•Input, power and controller output terminals are touch safe re
movable 3.30 to 0.0507 mm2 (12 to 22 AWG)
•Wire strip length 7.6 mm (0.30 in.)
•Torque 0.56 Nm (5.0 lb.-in.)
Universal Input
•Thermocouple, grounded or ungrounded sensors
•>20MΩ input impedance
•3µA open sensor detection
•Max. of 2KΩ source resistance
•RTD 2 or 3 wire, platinum, 100Ω and 1000Ω @ 0°C calibration to
DIN curve (0.00385Ω/Ω/°C)
•Process, 0-20mA @ 100Ω ,or 0-10V Î(dc) @ 20kΩ input impedance
Watlow EZ-ZONE ® PM PID Controller
Units
RTD, 1000 ohm
•User selectable heat/cool, on-off, P, PI, PD, PID or alarm action
•Auto-tune with TRU-TUNE®+ adaptive control algorithm
•Control sampling rates: input = 10Hz, outputs = 10Hz
•Accuracy (typical): ±30PPM at 77°F (25°C)
•+30/-100 PPM at -4 to 149°F (-20 to 65°C)
•Battery type: Rayovac 3V BR1225 lithium (recycle properly), only
installed in models with a real-time clock
•Battery typical life: three cumulative years of unpowered life at
77°F (25°C)
Accuracy
Range
High
J
Controller
Profile Ramp/Soak - Real Time Clock and Battery Back-up
Accuracy
Range
Low
K
Agency Approvals
•UL® Listed to UL® 61010-1 File E185611
•UL® Reviewed to CSA C22.2 No.61010-1-04
•UL® 50 Type 4X, NEMA 4X indoor locations, IP65 front panel
seal (indoor use only)
•FM Class 3545 File 3029084 temperature limit switches
•CE-See Declaration of Conformity RoHS and W.E.E.E.compliaint
•This equipment is suitable for use in Class 1, Div.2, Groups A, B, C and D or non-hazardous locations only. Temperature Code T4A
•UL® Listed to ANSI/ISA 12.12.01-2007 File E184390
•All models, CSA C22.2 No. 24 File 158031 Class 4813-02, CSA Approved
•UL® reviewed to Standard No. CSA C22.2 No.213-M1987, Cana-
dain Hazardous locations
Max
Error
@ 25
Deg C
•
119
•
Input Type
Range Low
Range High
J
-210 °C
1200 °C
K
-270 °C
1371 °C
T
-270 °C
400 °C
N
-270 °C
1300 °C
E
-270 °C
1000 °C
R
-50 °C
1767 °C
Appendix
•Switched dc/open collector = 30VÎ (dc) max. @ 100mA max. cur-
rent sink
•Solid state relay (SSR), FormA, 0.5A @ 24VÅ (ac) min., 264V Å (ac) max., opto-isolated, without contact suppression, 20 VA 120/240VÅ (ac) pilot duty
•Electromechanical relay, FormC, 5A, 24 to 240VÅ (ac) or 30VÎ (dc)max., resistive load, 100,000 cycles at rated load, 125 VA pilot duty at 120/240VÅ (ac), 25 VA at 24VÅ (ac)
•Electromechanical relay, FormA, 5A, 24 to 240VÅ (ac) or 30VÎ (dc) max., resistive load, 100,000 cycles at rated load, 125 VA pilot duty at 120/240VÅ (ac), 25 VA at 24VÅ (ac)
•NO-ARC relay, FormA, 15A, 24 to 240VÅ (ac), noVÎ (dc), resis-
tive load, 2 million cycles at rated load
•Universal process/retransmit, Output range selectable:
- 0 to 10V Î(dc) into a min. 1,000Ω load
- 0 to 20mA into max. 800Ω load
Resolution
- dc ranges: 2.5mV nominal
- mA ranges: 5 µA nominal
Calibration Accuracy
- dc ranges: ±15 mV
- mA ranges: ±30 µA
Temperature Stability
- 100 ppm/°C
Operating Range
S
-50 °C
1767 °C
B
-50 °C
1816 °C
C
0 °C
2315 °C
D
0 °C
2315 °C
F (PTII)
0 °C
1343 °C
RTD (100 ohm)
-200 °C
800 °C
RTD (1000 ohm)
-200 °C
800 °C
mV
-50 °C
50 °C
Volts
0 °C
10 °C
mAdc
0 °C
20 °C
mAac
-50 °C
50 °C
Potentiometer, 1K range
0 °C
1200 °C
Resistance, 5K range
0 °C
5000 °C
Resistance, 10K range
0 °C
10000 °C
Resistance, 20K range
0 °C
20000 °C
Resistance, 40K range
0 °C
40000 °C
Thermistor Input
Operator Interface
• 0 to 40KΩ, 0 to 20KΩ, 0 to 10KΩ, 0 to 5KΩ
• 2.252KΩ and 10KΩ base at 77°F (25°C)
• Linearization curves built in
• Third party Thermistor compatibility requirements
Base R
@ 25C
Alpha
Techniques
Beta
THERM
YSI
2.252K
Curve A
2.2K3A
004
A
10K
Curve A
10K3A
016
B
10K
Curve C
10K4A
006
C
•Dual 4 digit, 7 segment LED displays
•Advance, infinity, up and down keys, plus optional programmable EZ-KEY(s) depending on model size
•Typical display update rate 1Hz
•RESET key substituted for infinity on all models including the limit control
Prompt
[``t;C]
Dimensions
Size
2 Digital Input/Output Option - 2 DIO
•Digital input update rate 10Hz
- DC voltage
•Max. input 36V @ 3mA
•Min. high state 3V at 0.25mA
•Max. low state 2V
- Dry contact
•Min. open resistance 10KΩ
•Max. closed resistance 50Ω
•Max. short circuit 20mA
•Digital output rate 10 Hz
•SSR drive signal
•Maximum open circuit voltage is 22 to 25VÎ (dc)
•PNP transistor source
•Typical drive; 21mA @ 4.5V for DO5, 11mA @ 4.5V for DO6
•Current limit 24mA for Output 5 and 12mA Output 6
•Output 5 capable of driving one 3-pole DIN-A-MITE
•Output 6 capable of driving one 1-pole DIN-A-MITE
Width
Height
Display Character
Height
1/32
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
30.9 mm
(1.22 in)
left: 7.59 mm (0.299 in)
right: 5.90 mm (0.220 in)
1/4
100.8 mm
(3.97 in)
100.3 mm
(3.95 in)
100.3 mm
(3.95 in)
up: 11.43 mm (0.450 in)
middle: 9.53 mm (0.375 in)
low: 7.62 mm (0.300 in)
1/16
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
53.3 mm
(2.10 in)
up: 10.80 mm (0.425 in)
low: 6.98 mm (0.275 in)
1/8
(H)
101.6 mm
(4.00 in)
100.3 mm
(2.10 in)
53.9 mm
(1.22 in)
top: 11.4 mm (0.450 in)
middle: 9.53 mm (0.375 in)
bottom: 7.62 mm (0.300 in)
1/8
(V)
101.6 mm
(4.00 in)
53.3 mm
(2.10 in)
100.3 mm
(3.95 in)
top: 11.4 mm (0.450 in)
middle: 9.53 mm (0.375 in)
bottom: 7.62 mm (0.300 in)
Weight
Output Hardware
•Switched DC
•Maximum open circuit voltage is 22 to 25VÎ (dc)
•30mA max. per single output / 40mA max. total per paired
outputs (1 & 2, 3 & 4)
•Typical drive; 4.5VÎ (dc) @ 30 mA
•Short circuit limited to <50 mA
•NPN transistor sink
•Use dc- and dc+ to drive external solid-state relay
•1-pole DIN-A-MITE: up to 4 in parallel or 4 in series
•2-pole DIN-A-MITE: up to 2 in parallel or 2 in series
•3-pole DIN-A-MITE: up to 2 in series
Watlow EZ-ZONE ® PM PID Controller
Behind
Panel
(max.)
1/32 DIN (PM3)
1/8 DIN (PM8&9)
• Controller: 127 g (4.5 oz.)
• Controller: 284 g (10 oz.)
1/16 DIN (PM6)
• Controller: 186 g (6.6 oz.)
1/4 DIN (PM4)
• Controller: 331 g (11.7 oz.)
User's Guide
• 221.81 g (7.82 oz)
Modbus® is a trademark of AEG Schneider Automation Inc.
EtherNet/IP™ is a trademark of ControlNet International Ltd. used
under license by Open DeviceNet Vendor Association, Inc. (ODVA).
UL® is a registered trademark of Underwriters Laboratories Inc.
DeviceNet™ is a trademark of Open DeviceNet Vendors Associatlon.
Note:
These specifications are subject to change without prior notice.
•
120
•
Appendix
Ordering Information for PID Controller Models
P M __ __ __ __ __ - __ A A A __ __ __
Controller
EZ-ZONE® PID Controller Models
TRU-TUNE+® Adaptive Tune, red-green 7-segment displays
Package Size
3
6
8
9
4
Panel Mount 1/32 DIN
Panel Mount 1⁄16 DIN
Panel Mount 1⁄8 DIN Vertical
Panel Mount 1⁄8 DIN Horizontal
Panel Mount 1⁄4 DIN Horizontal
Primary Function
C
R
T
B
PID Controller with Universal Input
PID Controller with Universal Input and Profiling Ramp and Soak
PID Controller with Universal Input and Timer
PID Controller with Universal Input and Profiling Ramp and Soak
and Battery Backup with Real Time Clock
J
PID Controller with Thermistor Input
N
PID Controller with Thermistor Input and Profiling Ramp and Soak
E
PID Controller with Thermistor Input and Profiling Ramp and Soak
and Battery Backup with Real Time Clock
S
Custom Firmware
- Options B and E are not available with PM3 or PM6
Power Supply, Digital Input/Output
1
2
3
4
100 to 240VÅ (ac)
100 to 240VÅ (ac) plus 2 Digital I/O points
15 to 36VÎ (dc) and 24VÅ (ac)
15 to 36VÎ (dc) and 24VÅ (ac), plus 2 Digital I/O points
Output 1 and 2 Hardware Options
Output 1
Output 2
CA
Switched dc/open collector
None
CH
Switched dc/open collector
NO-ARC 15 A power control
CC
Switched dc/open collector
Switched dc
CJ
Switched dc/open collector
Mechanical relay 5 A, form A
CK
Switched dc/open collector
Solid-State Relay 0.5 A, form A
EA
Mechanical relay 5 A, form C
None
EH
Mechanical relay 5 A, form C
NO-ARC 15 A power control
EC
Mechanical relay 5 A, form C
Switched dc
EJ
Mechanical relay 5 A, form C
Mechanical relay 5 A, form A
EK
Mechanical relay 5 A, form C
Solid-State Relay 0.5 A, form A
FA
Universal process
None
FC
Universal process
Switched dc (cannot use variable time base)
FJ
Universal process
Mechanical relay 5 A, form A (cannot use variable time base)
FK
Universal process
Solid-State Relay 0.5 A, form A (cannot use variable time base)
AK
None
Solid-State Relay 0.5 A, form A
KH
Solid-State Relay 0.5 A, form A NO-ARC 15 A power control
KK
Solid-State Relay 0.5 A, form A Solid-state relay 0.5 A, form A
- Options CH, EH and KH are not available with PM3 (1/32 DIN)
Communications Options
A
None
1
EIA 485 Modbus RTU®
- Standard Bus EIA-485 always included - all models
Future Options
AAA
None
Isolated Input Option
A
D
None
Isolated Input 1
Custom Options
AA
12
AB
AC
AG
XX
Standard EZ-ZONE face plate
Class 1, Div. 2 (Not available with mechanical relay output types E, H, J)
EZ-ZONE logo and no Watlow name
No logo and no Watlow name
Conformal coating
Custom firmware, overlays, parameter settings
Watlow EZ-ZONE ® PM PID Controller
•
121
•
Appendix
Index
Symbols
[`A;bL] Alarm Blocking 66, 107
[AC;LF] AC Line Frequency 70, 103
[aC;sp] Produced Set Point 1 46
[`A;dL] Alarm Delay 67
[Ad;M] Modbus Address 73
[`Ad;S] Standard Bus Address 73
[A;dSP] Alarm Display 67, 68
[`A;hi] Alarm High Set Point 42,
66, 106
[`A;hy] Alarm Hysteresis 65, 106
[``Ai] Analog Input Menu 37, 50
[`Ain] Analog Input Value 52
[`A;LA] Alarm Latching 66, 106
[AL;E1] [AL;E2] [AL;E3] [AL;E4]
Alarm Error 1 to 4 28
[`A;Lg] Alarm Logic 65
[AL;h1] [AL;h2] [AL;h3] [AL;h4]
Alarm High 1 to 4 28
[AL;L1] [AL;L2] [AL;L3] [AL;L4]
Alarm Low 1 to 4 28
[ALM] Alarm Menu 42, 65
[`A;Lo] Alarm Low Set Point 42, 66,
106
[`A;Sd] Alarm Sides 66
[`A;Si] Alarm Silencing 67, 107
[`A;tP] Absolute Temperature 52
[A;tSP] Autotune Set Point 40, 59,
91
[Attn] Attention 28, 29, 106, 107
[`A;ty] Alarm Type 65, 106
[a;unt] Altitude Units 54
[`AUt] Autotune 40, 91
[bAUd] Baud Rate 73
[bPLS] 98
[`C;Ag] Cool Algorithm 58, 99
[`CAL] Calibration Menu 87
[`C;Cr] Cool Output Curve 58, 98
[`C_F] Display Units 70, 73
[Chan] Channel 72
[`C;hy] Cool Hysteresis 41, 58, 99
[C;led] Communications LED Activity 72
[`CLr] Clear 106
[`C;M] Control Mode 40, 62, 99
[C;MA] Control Mode Active 39
[CodE] Public Key 83, 86, 87
[CoM] Communications Menu 72,
74, 79, 84
[`C;Pb] Cool Proportional Band 41,
58, 92, 100
[`C;Pr] Cool Power 39, 92
[`C;SP] Closed Loop Set Point 40,
62
[`C;SP] Closed Loop Working Set
Point 39
[Ct;SP] Closed Loop Timer Set
Point 44, 69
[CUSt] Custom Menu 31, 91
[dAtE] Date of Manufacture 86, 87
[``db] Dead Band 41, 59, 102
[`dEC] Decimal 51
[`dio] Digital Input/Output Menu
39, 55
[`dir] Direction 55
[`do;S] Digital Output State 39
[dow] Day of Week 74
[d;prs] Display Pairs 49, 72
[`d;ti] Display Time 72
[`Ei;S] Event Input Status 39
[ELi;o] Electrical Input Offset 87
[ELi;S] Electrical Input Slope 87
[ELo;o] Electrical Output Offset 87
[`End] End 82
[Ent1] Active Event Output 1 46,
47
[Ent2] Event Output 2 81
[Er;i1] Error Input 1 28
[FAiL] Input Error Failure 60, 98
[``Fi] Digital Output Function
Instance 55, 57
[``Fi] Function Instance 70
[``Fi] Output Function Instance
63, 64
[`Fil] Filter 51, 54
[`FiL] Filter Time 95
[``Fn] Action Function 57, 70
[``Fn] Output Function 55, 62, 64
[``Fn] Function 54
[``Fn] Function 52
[`FUn] Function Key Menu 69
[gLbL] Global Menu 70
[`gSd] Guaranteed Soak Deviation
71
[GSd1] Guaranteed Soak Deviation
1 71
[`gSE] Guaranteed Soak Enable
71
[`h;Ag] Heat Algorithm 57, 99
[`h;hy] Heat Hysteresis 41, 58, 99
[hoUr] Hours 36, 44, 46, 69, 74
[`h;Pb] Heat Proportional Band 41,
58, 92, 100
[`h;Pr] Heat Power 39, 92
[`i;CA] Calibration Offset 37, 51,
93–94
[`id;S] Idle Set Point 41, 62
[`i;Er] Input Error Latching 51
[`i;Er] Input Error Status 37, 52
[`iP;1] Input Point 1 52
[`iP;2] Input Point 2
[`iP;3] Input Point 3
[`iP;4] Input Point 4 52
[`iP;2] Input Point 2 52
[`iP;3] Input Point 3 53
[`iP;4] Input Point 4 53
Watlow EZ-ZONE ® PM PID Controller
•
122
•
[`iP;5] Input Point 5 52, 53
[`iP;6] Input Point 6 53
[`iP;7] Input Point 7 53
[`iP;8] Input Point 8 53
[`iP;9] Input Point 9 54
[iP;10] Input Point 10 54
[``JC] Jump Count Remaining 47
[``JL] Jump Loop 82
[``JS] Jump Step 81
[`L;dd] Open Loop Detect Deviation 61
[`L;dE] Open Loop Detect Enable
60
[`L;dt] Open Loop Detect Time 61
[`leu] Active Level 69
[`leu] Action Level 56
[`Lin] Linearization 50
[`Lnr] Linearization Menu 37, 52
[`LoC] Security Setting Menu 84,
86
[loC;l] Locked Access Level 83, 85
[LoC;o] Lock Operations Page 84
[LoC;P] Lock Profiling Page 85, 86
[LooP] Control Loop Menu 57
[LooP] Loop Menu 40
[LP;o1] Loop Open Error 28
[LP;o1] Loop Open Error 1 28
[LP;r1] Loop Reversed Error 28
[LP;r1] Loop Reversed Error 1 28
[MAn] 98
[MAn] Manual Power 60
[Map] Data Map 35, 73
[M;hL] Modbus Word Order 73
[Min] Minutes 36, 44, 46, 69, 74
[Mon] Monitor Menu 39
[`Mu] Electrical Measurement 87
[`nU;S] Non-volatile Save 73
[`o;CA] Calibration Offset 65
[`o;Ct] Output Control 55, 63
[`o;Fn] Output Function 93, 97
[oFSt] PV Offset 38
[`o;hi] Output High Power Scale
56, 63
[`o;Lo] Output Low Power Scale
56, 63
[``oP] Open Loop Set Point 41
[`oP;1] Outpoint Point 1 52
[`oP;2] Output Point 2 53
[`oP;3] Output Point 3 53
[`oP;4] Output Point 4 53
[`oP;5] Output Point 5 53
[`oP;6] Output Point 6 53
[`oP;7] Output Point 7 53
[`oP;8] Output Point 8 53
[`oP;9] Output Point 9 54
[oP;10] Output Point 10 54
[`o;SP] Manual Power 62
[`o;tb] Output Time Base 56, 63
Appendix
[otPt] Output Menu 62
[`o;ty] Output Type 63, 97
[``o;u] Output Value 38
[P;ACr] Action Request 46
[`PAr] Parity 73
[pas;a] Administrator Password 83,
86
[pas;e] Password Enable 83, 85
[PASS] Password 83, 86
[pas;u] User Password 83, 85
[PCoL] Protocol 72
[`p;dl] Peltier Delay 59
[`P;EE] Process Error Enable 51
[`P;EL] Process Error Low 51
[``Pn] Part Number 86, 87
[poti] Power Off Time 49, 71
[`pro] Process 52
[P;SP1] Produced Set Point 1 44
[P;StA] Profile Status Menu 45
[P;tyP] Profile Type 71
[p;unt] Pressure Units 54
[``Pu] Process Value Menu 54
[`Pu;A] Process Value Active 39
[rAtE] Rate 82
[`r;bS] Ready Band State 44, 69
[`rdY] Ready Band 69
[`rEu] Software Revision 86
[`r;hi] Range High 51, 65, 96
[``rh] Relative Humidty 52
[`r;Lo] Range Low 50, 64, 96
[rLoC] Read Lockout Security 85
[roll] Rolling Password 83, 85
[``rP] Ramp Action 61, 103
[`rP1] Ramping 1 28
[`r;rt] Ramp Rate 61, 103
[``r;r] Thermistor Resistance
Range 51
[`r;SC] Ramp Scale 61, 103
[`r;Sr] Retransmit Source 64, 97
[`rt;L] RTD Leads 50
[`r;tp] Relative Temperature 52
[R;typ] Ramping Type 71
[S;bLd] Software Build 86
[`SEC] Seconds 36, 44, 46, 69
[`SEn] Sensor Type 50, 93, 95
[SFn;A] Source Function A 65, 68
[SFn;C] Source Function C 68
[SFn;D] Source Function D 68
[`S;hi] Scale High 50, 64, 96, 97
[`Si;A] Source Instance A 68, 71
[`Si;B] Source Instance B 71
[`Si;C] Source Instance C 68
[`Si;D] Source Instance D 68
[`SiL] Silence 106
[`S;Lo] Scale Low 50, 64, 96, 97
[SLoC] Set Lockout Security 85,
108, 109
[``Sn] Serial Number 86
[SoAh] Soak 82
[SP;Lo] Minimum Manual Power 62
[s;stp] Profile Start Step 57
[``St] Signal Time 69
[`StP] Active Step 46
[S;tyP] Active Step Type 46
[`Su;A] Source Value A 38, 43
[`Su;C] Source Value C 44
[`Su;d] Source Value D 44
[sutb] Synchronized Variable Time
Base 49, 72
[t;Agr] User Tune Aggressiveness
59, 91
[t;bnd] TRU-TUNE+™ Band 59, 92
[``t;C] Thermistor Curve 51
[``td] Time Derivative 41, 58, 92,
101
[tE;o1] Timer Event Output 1 44
[tE;o2] Timer Event Output 2 44
[tE;o3] Timer Event Output 3 44
[t;For] Time Format 69
[`t;gn] TRU-TUNE+™ Gain 59, 92
[``ti] Time 82
[``ti] Time Integral 41, 58, 92,
101
[ti;En] Timer Enable 68
[ti;St] Timer Start Method 68
[tMr] Timer Menu, Operations
Page 43
[tMr] Timer Menu, Setup Page 68
[``t;r] Time Remaining 44, 68
[t;SP1] Target Set Point 1 46
[t;tUn] TRU-TUNE+™ Enable 59,
92
[tUn1] Tuning 28
[tUn1] [tUn2] Tuning 1 or 2 28
[tUn1] Tuning 1 28
[uAL;h] Value to high 28
[`UFA] User Failure Action 60
[Unit] Units 52
[USr;r] User Restore Set 72, 90
[USr;S] User Save Set 72
[UStP] Unused Step 82
[uAL;L] Value to low 28
[W;bo] Wait For Both 82
[WE;2] Wait Event 2 80
[2one] Zone 72
A
Absolute Temperature 52
AC Line Frequency 70, 103
Action Function 57
Active Event Output (1 or 2) 46, 47
Active Step 46
adaptive tuning 92
Address Modbus 73
Address Standard Bus 73
Administrator Password 83, 86
agency approvals 3
alarm blocking 107
alarm latched 43
Watlow EZ-ZONE ® PM PID Controller
•
123
•
Alarm Menu 42, 65
alarms 105
Blocking 66, 107
deviation 106
Display 67, 68
Hysteresis 65, 106
Latching 66, 106
Logic 65
process 106
set points 106
Sides 66
Silencing 67, 107
Source 65
Type 65
alarm silenced 43
alarm state 42
Alarm Type 106
Altitude Units 48, 54
Analog Input Menu 37, 50
Assembly Definition
Addresses 118
Assembly Definition Addresses and
Assembly Working Addresses
118
Assembly Working Addresses 111,
118
Attention Codes 29
auto (closed loop) control 98, 99
Autotune 91
Autotune Aggressiveness 59
Autotune Set Point 40, 59, 91
autotuning 91–92
autotuning with TRU-TUNE+™ 92
B
Baud Rate 73
Blocking 66, 107
bumpless transfer 99
C
Calibration Menu 87
Calibration Offset 37, 51, 65, 93–94
changing the set point 29
Channel 72
chattering output 99
chemical compatibility 13
CIP (Common Industrial Protocol)
34
clear alarm 43
Clear Request 67
Closed Loop Set Point 40, 62
Closed Loop Timer Set Point 44, 69
Closed Loop Working Set Point 39
Communications LED Action 72
Communications Menu 72, 74, 79,
84
Setup Page 36, 48
Control 63
Control Loop Menu 57
control methods 98
Appendix
Control Mode 40, 62, 99
Control Mode Active 39
Control Module Menus
Factory Page
Calibration Menu 87
Security Setting Menu 84, 86
Operations Page
Alarm Menu 42
Analog Input Menu 37
Digital Input/Output Menu 39
Linearization Menu 37
Loop Menu 40
Monitor Menu 39
Process Value Menu 38
Profile Status Menu 45
Timer Menu 43
Setup Page
Alarm Menu 65
Analog Input Menu 50
Communications Menu 72, 74,
79, 84
Control Loop Menu 57
Digital Input/Output Menu 55
Global Menu 70
Linearization Menu 52
Output Menu 62
Process Value 54
Cool Algorithm 58, 99
Cool Hysteresis 41, 58, 99
Cool Output Curve 58, 98
Cool Power 39, 92
Cool Proportional Band 41, 58, 92,
100
Countdown State 45
Custom Menu 91
D
Data Map 35, 73
Date of Manufacture 86, 87
Day of Week 74
dead band 101, 102
Dead Band 41, 59, 102
Decimal 51
default Home Page parameters 27,
29
Delay 67
deviation alarms 106
Digital Input Function 70
Digital Input/Output Menu 39, 55
dimensions 9, 11
1/16 DIN 8
Direction 55
Display 67, 68
Display Pairs 49, 72
displays 27
Display Time 72
Display Units 70
Down Key 27
E
Elapsed Signal Time 45
Elapsed Time 45
Electrical Input Offset 87
Electrical Input Slope 87
Electrical Measurement 87
Electrical Output Offset 87
Electrical Output Slope 87
End 82
End Set Point Value 81
Event Output (1 and 2) 81, 82
Event Status 39
EZ Key 107
Input Point 5 48
Input Point 6 48
Input Point 7 48
Input Point 8 48
Input Point 9 48, 54
Input Point 10 48, 54
inputs 4
Input Sensor Type 93
Input State 39
installation 12
Instance 70
F
Jump Count 81
Jump Count Remaining 47
Jump Loop 82
Jump Step 81
Factory Page 83
Filter 54
Filter Time 51, 95
filter time constant 95
Fixed Power 60
Function 48, 54, 93
Function Instance 55, 57
Function Key Menu 107
G
Global Menu 70
Setup Page 36, 48
Guaranteed Soak Devia-
tion 49
Guaranteed Soak Deviation 71
Guaranteed Soak Enable 49, 71
H
Heat Algorithm 57, 99
Heat Hysteresis 41, 58, 99
Heat Power 39, 92
Heat Proportional Band 41, 58, 92,
100
High Power Scale 56, 63
high range 96
high scale 95, 96
High Set Point
Alarm 42, 43, 66, 106
Loop 61
Home Page 29, 91
Hours 44, 46, 69, 74, 79
Hours Remaining 36
Hysteresis 65, 106
I
Idle Set Point 41, 62
Indicator Request 45
Input Error Failure 60, 98
Input Error Latching 51, 99
Input Error Status 37, 52
input events 5
input features 93–95
calibration 93
Input Point 1 48, 52
Input Point 2 48, 52
Input Point 3 48
Input Point 4 48
Watlow EZ-ZONE ® PM PID Controller
•
124
•
J
K
keys and displays
1/16 DIN 27
L
Latching 66, 106
Level 69
Linearization 35, 50
Linearization Menu 37, 52
Locked Access Level 83, 85
Lockout Menu 108
Logic 65
Loop Menu 40
Low Power Scale 56, 63
low range 96
low scale 95, 96
Low Set Point
Alarm 42, 106
Loop 61, 95
M
Manual Control Indicator Light 99
manual (open loop) control 98, 99
Manual Power 62
manual tuning 92
Message Action 28
message, display 28
Minutes 44, 46, 69, 74, 79, 80
Minutes Remaining 36
Modbus Default Assembly Structure
80-119 119
Modbus - Programmable Memory
Blocks 118
Modbus Word Order 73
Monitor Menu 39
N
navigating
Factory Page 83
pages and menus 33
Profiling Page 75
Setup Page 36, 48
network wiring 24
Appendix
no-arc relay 97
Non-volatile Save 49
O
Offset 38
on-off control 99, 100
Open Loop Detect Deviation 61
Open Loop Detect Enable 60
Open Loop Detection 107
Open Loop Detect Time 61
Open Loop Set Point 41
Operations Page 36
output configuration 98
Output Error 38, 45
output features 96
Output Function 55, 64, 97
Output Function Instance 63
Output Menu 62
Output Point 1 48, 52
Output Point 2 48
Output Point 3 48
Output Point 4 48
Output Point 5 48
Output Point 6 48
Output Point 7 48
Output Point 8 48
Output Point 9 48, 54
Output Point 10 48, 54
output power scaling 98
outputs 4
Output State 39
Output Type 63, 97
Output Value 38
P
P3T armor sealing system 3
Parameter 1 to 20 84
Parameter ID 34
Parity 73
Part Number 86, 87
Password 86
Password Enable 83
Peltier Delay 48, 59
Power Out Time 49, 71, 72
Pressure Units 48, 54
process alarms 106
Process Error Enable 51
Process Error Low 51
Process Value 37, 52, 54
Process Value Active 39, 40
Process Value Menu 38
Produced Set Point 1 44, 46
Profibus 35
Profibus Index 34
Profile Setup 75
Profile Start 45
Profile Status Menu 45
Profile Type 71
Profiling Page 75
profiling parameters 78, 79
programming the Home Page 91
proportional control 100
plus integral (PI) control 101
plus integral plus derivative (PID)
control 101
Protocol 72
[P;Str] Profile Start 45
Public Key 83, 86, 87
Q
R
Ramp Action 61, 103
Ramping Type 71
Ramp Rate 61, 103
Ramp Scale 61, 103
Range High 51, 65, 96
Range Low 50, 64, 96
Rate 82
Ready Band 69
Ready Band State 44, 69
Real Time Clock 35, 49
Relative Humidty 52
Relative Temperature 52
removing mounted controller 12
responding to a displayed message
28–29
restoring user settings 90
retransmit 96, 97
Retransmit Source 64, 97
Rolling Password 83, 85
RTD Leads 50
S
saving user settings 89
Scale High 50, 64, 96, 97
Scale Low 50, 64, 96, 97
Seconds 44, 46, 79
Seconds Remaining 36
Security Setting 84, 86
sensor selection 95
Sensor Type 50, 93, 95
Serial Number 86
set point high limit 95
Set Point High Limit Open Loop 62
set point low limit 95
Set Point Low Limit Open Loop 62
Setup Page 48
Timer Menu 68
Sides
Alarm 66
Signal Time 69
silence alarm 43
Silence Alarm 67
Silencing 67, 107
single set point ramping 103
Soak 82
Software Build 86
Software Revision 86
Source 65
Watlow EZ-ZONE ® PM PID Controller
•
125
•
Source Function A 68
Source Function C 68
Source Function D 68
Source Instance A 68, 71
Source Instance B 71
Source Instance C 68
Source Instance D 68
Source Value A 38, 43
Source Value C 44
Source Value D 44
[SP;hi] Maximum Manual Power 62
Starting a Profile 76
Step Type 46
Synchronized Variable Time Base
49
T
Target Set Point 79
Target Set Point Loop 1 46
temperature units indicator lights 27
Thermistor 18, 50
Time 82
Time Base 56, 63
Time Base Type 55
Time Derivative 41, 58, 92, 101
Time Format 69
Time Integral 41, 58, 92, 101
Time Remaining 44, 68
Timer Enable 68
Timer Event Output 1 44
Timer Event Output 2 44
Timer Event Output 3 44
Timer Start Method 68
Timer Timing 45
TRU-TUNE+™ Band 59, 92
TRU-TUNE+™ Enable 59, 92
TRU-TUNE+™ Gain 59, 92
tuning the PID parameters 91
Type 65
U
Unused Step 82
upper display 27
User Failure Action 60
User Password 83, 85
User Restore Set 90
User Save Set 90
User Tune Aggressiveness 91
Using EZ-ZONE® Configurator Software 111
using the software 107
V
variable time base 102, 103
W
Wait Event (1 and 2) 80
Wait For Both 82
Wait For Process Instance 80
weight 121
wiring
Appendix
digital input or output 5 16
high power 16
input 1 potentiometer 17
input 1 process 17
input 1 RTD 17
input 1 thermocouple 17
input 2 thermocouple 18
low power 16
Modbus RTU or Standard Bus EIA-485 communications 24
output 1 mechanical relay, form C 21
output 1 solid-state relay, form A 21
output 1 switched dc/open collector 19, 20
output 1 universal process 21
output 2 mechanical relay, form A 22
output 2 no-arc relay, form A 22
output 2 solid-state relay, form A 23
output 2 switched DC/open collector 22
output 3 switched dc/open collector 23
Standard Bus EIA-485 communications 23
X
Y
Z
Zone 72
Zone Display 73
Watlow EZ-ZONE ® PM PID Controller
•
126
•
Appendix
Declaration of Conformity
Series EZ-ZONE® PM
WATLOW Electric Manufacturing Company
ISO 9001since 1996.
1241 Bundy Blvd.
Winona, MN 55987 USA
Declares that the following product:
®
Series EZ-ZONE PM (Panel Mount)
Designation:
Model Numbers:
PM (3, 6, 8, 9 or 4)(Any Letter or number) – (1, 2, 3 or 4)(A, C, E, F or
K) (A, C, H, J or K)(Any letter or number) – (Any letter or number)(A, C,
E, F or K)(A, C, H, J or K) (Any three letters or numbers)
Classification:
Temperature control, Installation Category II, Pollution degree 2, IP65
Rated Voltage and Frequency: 100 to 240 V~ (ac 50/60 Hz) or 15 to 36 Vdc/ 24 V~ac 50/60 Hz
Rated Power Consumption:
10 VA maximum PM3, PM6 Models.
14 VA maximum PM8, PM9, PM4 Models
Meets the essential requirements of the following European Union Directives by using the relevant
standards show below to indicate compliance.
2004/108/EC Electromagnetic Compatibility Directive
EN 61326-1
2013
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-11
EN 61000-3-2
1
EN 61000-3-3
SEMI F47
2009
2010
2012
2006
2014
2004
2009
2013
2000
Electrical equipment for measurement, control and laboratory use
– EMC requirements (Industrial Immunity, Class B Emissions).
Electrostatic Discharge Immunity
Radiated Field Immunity 10V/M 80–1000 MHz, 3 V/M 1.4–2.7 GHz
Electrical Fast-Transient / Burst Immunity
Surge Immunity (Also compliant with IEC 61000-4-5 2014)
Conducted Immunity
Voltage Dips, Short Interruptions and Voltage Variations Immunity
Harmonic Current Emissions (Also compliant with IEC 61000-3-2 2014)
Voltage Fluctuations and Flicker
Specification for Semiconductor Sag Immunity Figure R1-1
1
For mechanical relay loads, cycle time may need to be extended up to 160 seconds to meet flicker
requirements depending on load switched and source impedance.
EN 61010-1
2006/95/EC Low-Voltage Directive
20112
Safety Requirements of electrical equipment for measurement,
control and laboratory use. Part 1: General requirements
2
Compliance with 3rd Edition requirements with use of external surge suppressor installed on 230 Vac~ power line units.
Recommend minimum 1000 V peak to maximum 2000 V peak, 70 joules or better part be used.
Compliant with 2011/65/EU RoHS2 Directive
Per 2012/19/EU W.E.E.E Directive
Please Recycle Properly.
Joe Millanes
Name of Authorized Representative
Winona, Minnesota, USA
Place of Issue
Director of Operations
Title of Authorized Representative
September 2014
Date of Issue
Signature of Authorized Representative
CE DOC EZ-ZONE PM-09-14
Watlow EZ-ZONE ® PM PID Controller
•
127
•
Appendix
How to Reach Us
Corporate Headquarters
Watlow Electric Manufacturing Company
12001 Lackland Road
St. Louis, MO 63146
Sales: 1-800-WATLOW2
Manufacturing Support: 1-800-4WATLOW
Email: info@watlow.com
Website: www.watlow.com
From outside the USA and Canada:
Tel: +1 (314) 878-4600
Fax: +1 (314) 878-6814
Latin America
Watlow de México S.A. de C.V.
Av. Fundición No. 5
Col. Parques Industriales
Querétaro, Qro. CP-76130
Mexico
Tel: +52 442 217-6235
Fax: +52 442 217-6403
Europe
Watlow France
Tour d'Asnières.
4 Avenue Laurent Cély
92600 Asnières sur Seine
France
Tél: + 33 (0)1 41 32 79 70
Télécopie: + 33(0)1 47 33 36 57
Email: info@watlow.fr
Website: www.watlow.fr
Watlow GmbH
Postfach 11 65, Lauchwasenstr. 1
D-76709 Kronau
Germany
Tel: +49 (0) 7253 9400-0
Fax: +49 (0) 7253 9400-900
Email: info@watlow.de
Website: www.watlow.de
Watlow Italy S.r.l.
Viale Italia 52/54
20094 Corsico MI
Italy
Tel: +39 024588841
Fax: +39 0245869954
Email: italyinfo@watlow.com
Website: www.watlow.it
Asia and Pacific
Watlow Ibérica, S.L.U.
C/Marte 12, Posterior, Local 9
E-28850 Torrejón de Ardoz
Madrid - Spain
T. +34 91 675 12 92
F. +34 91 648 73 80
Email: info@watlow.es
Website: www.watlow.es
Watlow UK Ltd.
Linby Industrial Estate
Linby, Nottingham, NG15 8AA
United Kingdom
Telephone: (0) 115 964 0777
Fax: (0) 115 964 0071
Email: info@watlow.co.uk
Website: www.watlow.co.uk
From outside The United Kingdom:
Tel: +44 115 964 0777
Fax: +44 115 964 0071
Watlow Singapore Pte Ltd.
16 Ayer Rajah Crescent,
#06-03/04,
Singapore 139965
Tel: +65 6773 9488Fax: +65 6778 0323
Email: info@watlow.com.sg Website: www.watlow.com.sg
Watlow Korea Co., Ltd.
#1406, E&C Dream Tower, 46, Yangpyeongdong-3ga
Yeongdeungpo-gu, Seoul 150-103
Republic of Korea
Tel: +82 (2) 2628-5770
Fax: +82 (2) 2628-5771
Website: www.watlow.co.kr
Watlow Australia Pty., Ltd.
4/57 Sharps Road
Tullamarine, VIC 3043
Australia
Tel: +61 3 9335 6449
Fax: +61 3 9330 3566
Website: www.watlow.com
Watlow Malaysia Sdn Bhd
1F-17, IOI Business Park
No.1, Persiaran Puchong Jaya Selatan
Bandar Puchong Jaya
47100 Puchong, Selangor D.E.
Malaysia
Tel: +60 3 8076 8745 Fax: +60 3 8076 7186
Email: vlee@watlow.com
Website: www.watlow.com
Watlow Electric Manufacturing Company (Shanghai) Co. Ltd.
Room 501, Building 10, KIC Plaza
290 Songhu Road, Yangpu District
Shanghai, China 200433
China
Phone:
Local: 4006 Watlow (4006 928569)
International: +86 21 3381 0188
Fax: +86 21 6106 1423
Email: vlee@watlow.cn
Website: www.watlow.cn
瓦特龍電機股份有限公司
80143 高雄市前金區七賢二路189號 10樓之一
電話: 07-2885168
傳真: 07-2885568
Watlow Electric Taiwan Corporation
10F-1 No.189 Chi-Shen 2nd Road Kaohsiung 80143
Taiwan
Tel: +886-7-2885168 Fax: +886-7-2885568
Your Authorized Watlow Distributor
ワトロー・ジャパン株式会社
〒101-0047 東京都千代田区内神田1-14-4
四国ビル別館9階
Tel: 03-3518-6630 Fax: 03-3518-6632
Email: infoj@watlow.com
Website: www.watlow.co.jp
Watlow Japan Ltd.
1-14-4 Uchikanda, Chiyoda-Ku
Tokyo 101-0047
Japan
Tel: +81-3-3518-6630 Fax: +81-3-3518-6632
Email: infoj@watlow.com Website: www.watlow.co.jp
TOTAL
CUSTOMER
SATISFACTION
3 Year Warranty
Watlow EZ-ZONE ® PM PID Controller
•
128
•
Appendix
Download PDF