Catalogue Sheet: ULTP Series

Catalogue Sheet: ULTP Series
Type:
new product
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
TYPICAL SPECIFICATIONS
ULTIMA™ SERIES
Thermoplastic Pictogram
Combination Unit
FEATURES
The Ultima™ Series of combination units
(unit equipment and pictogram exit sign) are
designed to complement designer’s look and
ease of installation with performance and
cost-competitiveness.
• One-pack combination of battery
unit and Pictogram Sign, a compact
and contemporary design
• Durable injection-molded thermoplastic
housing with push-to-snap design
• Available in single or double face
configurations both with means for
ceiling mounting
• Supplied standard with two (single
face) or three pictogram films
(universal face) for direction selection
• Two MR16 LED or halogen lamps,
shielded by a clear polycarbonate cover
• Twin LED lights provide up to 89 feet
of egress illumination on a 6-foot
wide path
• Sealed, maintenance-free, LeadCalcium or Nickel-Metal-Hydride
batteries
• Remote load capacity: one unit
equipment with LED remote lights
covers up to 712 feet (217m)
of egress illumination
• Remote load capacity up to 92W
when using LED lamp option
• Dual voltage input: 120/347VAC
or 120/277VAC
• C omes standard with non-audible
auto-diagnostics
• Optional vandal-resistant shield
with tamper-proof screws
• Certified CSA C22.2 No.141
• Optional: Nexus® Compatible
Supply and install the Ready-Lite® Ultima™ Series combination of unit equipment and pictogram exit sign.
The unit frame and face plates shall be made of injection-molded thermoplastic. The faceplates shall feature a
uniformly illuminated legend. The light source shall be long-life white light-emitting diodes (LED). The unit shall
be equipped with two emergency heads with tool-less adjustable swivels and long-life MR-16 LED lamps of
___ V and ___ W. Each lamp shall be protected by a snap-on, shock-absorbent, transparent polycarbonate
cover.
The AC input voltage shall be standard 120/347VAC 60Hz. The unit shall be equipped with a test switch and
a green pilot light, located on the face plate above the pictogram legend. The battery charger shall be driven
by a micro-controller. All electronic circuitry (charger, LED driver, signage LED’s) shall be installed on a single
printed circuit board PCB. The unit equipped with self-testing / self-diagnostic features shall automatically
self test for one minute every 30 days, 10 minutes in the 6th month and 30 minutes annually. When a fault
is detected, the bi-color pilot-light shall turn from green to red and shall flash following a particular code. The
code description shall be displayed on a label next to the pilot light to identify the failure type: battery, charger
circuitry, LED lamps for signage, or emergency lights.
The combination unit shall meet or exceed the standard CSA C22.2 No.141-10.
The Pictogram combo unit shall be Ready-Lite® Model:
.
U L T I M A ™ FA M I LY
Ultima™ Exit P. 53
Ultima™ Combo P. 56-57
Ultima™ Battery P. 122-123
WIRE GUARDS
460.0078-RL
wall mount
POWER CONSUMPTION
MODEL
AC SPECS
Pictogram Sign Module
less than 4W
L20
0.12/0.04 A
L50
120/347VAC
12L50
12H5
0.24/0.08 A
12H10
58
30MIN
WATTAGE CAPACITY
1H00 1H30 2H00
-
4H00
-
-
-
-
25
15
12
8
-
50
30
24
16
8
50
30
24
16
8
50
36
24
18
9
100
72
48
36
18
Type:
Project/Location:
Contractor:
Prepared By:
Date:
Model No.:
Made in Canada
DIMENSIONS
Dimensions are approximate and subject to change.
PICTO STRAIGHT
FROM HERE
< PICTO LEFT
FROM HERE
ULTIMA™ SERIES
PICTO > RIGHT
FROM HERE
Thermoplastic Pictogram
Combination Unit
17” [43.2 cm]
11-1/4” [28.7 cm]
12-3/8” [31.5 cm]
4-7/8” [12.3 cm]
3-3/8” [8.5 cm]
ORDERING INFORMATION
POWERPACK
# OF HEADS
HEAD STYLE/ WATTAGE
FACES/MOUNTING
VOLTAGE
COLOUR
CHARGER TYPE
L20= 6V-25W LeadCalcium
L50= 6V-50W LeadCalcium
12L50= 12V-50W
LeadCalcium
12H5= 12V-50W
NiMH
12H10= 12V-100W
NiMH
Blank= no
heads
-2= two
heads
LD1= M
R16 LED, 6V-4W
LD7= M
R16 LED, 12V-4W
LD9= M
R16 LED, 12V-5W
LD10= MR16 LED, 12V-6W
M6= MR16 halogen,
6V-6W
M10= MR16 halogen,
6V-10W or 12V-10W
M12= MR16 halogen,
12V-12W
M20= MR16 halogen,
12V-20W
-ULTP1= s ingle face
ceiling or
wall mount
-ULTP2= double
face ceiling
mount
-ULTP1N= s ingle face
wall mount
(less
canopy)
-ULTPU= universal,
two faces
backplate
and canopy
2= 120/277VAC
3= 120/347VAC
B= black
W= factory
white
Blank= autodiagnostics,
non-audible
AD= autodiagnostics
NEX= NEXUS®
system
interface
NEXRF= wireless
NEXUS®
system
interface
OPTIONS
Blank= no options
D3= time delay (15 mins.)
TP= tamper-proof screws*
VRTP1= polycarbonate shield
with tamper-proof
screws, single face*
VRTP2= polycarbonate shield
with tamper-proof
screws, double face*
*091957-RL= tamper-proof bit (sold
seperately)
*VRTP1 & VRTP2 are not available
with -ULTPU
E X A M P L E : L 2 0 - 2 M 6 - U LT P 1 3 W
59
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement