INSTRUCTION MANUAL 540TV Lines Super High Resolution Color Camera 1/3'' INTERLINE TRANSFER CCD HIGH RESOLUTION ISSUE 1 - SEPTEMBER 2008 LIMITATION OF LIABILITY THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL RESPECTS, HOWEVER, WE CANNOT ASSUME RESPONSIBILITY FOR ANY CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH CHANGES. - ii - WARNINGS AND CAUTIONS: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT. CAUTION: CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. PRECAUTIONS Safety ----------------------------------------- Installation ----------------------------------- Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by the qualified personnel before operating it any further. Do not install the unit in an extremely hot or humid place or in a place subject to excessive dust, mechanical vibration. Unplug the unit from the wall oulet if it is not going to be used for several days or more. To disconnect the cord, pull it out by the plug. Never pull the cord itself. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit. Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials(curtains, draperies) that may block the ventilation holes. Height and vertical linearity controls located at the rear panel are for special adjustments by qualified personnel only. Cleaning -------------------------------------Clean the unit with a slightly damp soft cloth. Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the finish of the unit. Retain the original carton and packing materials for safe transport of this unit in the future. - iii - FCC COMPLIANCE STATEMENT FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE. CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. NORME NMB-003 DU CANADA. CE COMPLIANCE STATEMENT WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. - iv - IMPORTANT SAFEGUARDS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that product heat.. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where thy exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO. -v- TABLE OF CONTENTS INTRODUCTION 1 CAMERA OVERVIEW 2 FUNCTION DESCRIPTION 3 CONNECTIONS 5 CONTENTS OF PACKAGE 6 MANUAL IRIS LENS ADJUSTMENT 6 VIDEO AUTO IRIS INSTALLATION & ADJUSTMENT 7 DC AUTO IRIS LENS INSTALLATION & ADJUSTMENT BACK FOCUS ADJUSTMENT 8 10 ZOOM LENS BACK FOCUS ADJUSTMENT 11 TROUBLESHOOTING AND MAINTENANCE 12 SPECIFICATIONS 13 - vi - INTRODUCTION The camera provides high-quality images using SONY CCD technology especially designed for closed-circuit television (CCTV) and security surveillance applications. Features: High resolution and high performance 1/3" SONY Super HAD CCD technology Excellent picture quality 540 lines(Color) of resolution 0.25 Lux(Color) / 0.01 Lux(B/W) @ F1.2 Sensitivity (True D&N) 0.25 Lux(Color) @ F1.2 Sensitivity (Digital D/N) C/CS, backfocus cam for easy adjustment Auto electronic shutter [1/60(1/50) ~ 1/100,000] and manual electronic Shutter modes Auto Trace White balance modes Selectable BLC function Day & Night (True D&N / Digital D/N) AGC (Auto Gain Control) Video out(BNC) Quick connect for video or DC lens with 4-pin connector Operates in 100-240 VAC IMPORTANT : The user of this camera is responsible for checking and complying with local, state, and federal laws and statutes concerning the recording and monitoring of audio signals. 1 CAMERA OVERVIEW C Mount Ring (Option) 120.0mm (C MOUNT LENS) (CS MOUNT LENS) SIDE VIEW 1/4-20UNC 43.0mm 14.0mm 56.0mm 1-32UNEF 7.0mm 66.0mm FRONT VIEW TOP VIEW 2 FUNCTION DESCRIPTION - SIDE VIEW 1 2 2 1 Focus Adjusting Fixing Screw 2 Auto Iris Lens Connector - REAR VIEW 1 1 IRIS LEVEL AUTO COLOR D/N 2 2 FUNCTION SWITCH 3 AC Power Cord 5 4 POWER INDICATOR 5 VIDEO OUTPUT CONNECTOR 3 4 <DC12V> 3 1) IRIS LEVEL Adjust the DC-type auto iris lens for an optimum picture using this volume. 2) FUNCTION SWITCH - E/I (on/off) When set to the ON position, the electronic iris switch automatically varies the camera's shutter to mimic auto-iris control, allowing fixed or manual iris lenses to be used in a wider range. When this switch is set to ON, turn the F/F switch OFF. - FF (on/off) This function is used for removing flicker, when camera signal format does not coincide with power source frequency being used. - BLC (on/off) This on/off switch controls backlight compensation. When set to ON, the camera will automatically try to maintain proper exposure in the specific area even if the lighting level changes. - AGC (on/off) The auto gain control switch allows the video signals to maintain a constant level. This switch is useful when using the camera at low-light levels and when lighting levels change over time. For best low light conditions, this switch should set to ON. - Day/Night (Auto/Color) Use this switch to set the camera Day/Night mode Auto(ON) or Color(OFF) Auto : D/N mode converse automatically (AGC must set to ON) Color : Only Color - A/I (DC/VIDEO) Use this switch to set the auto iris type. 3) POWER INPUT TERMINAL 4) POWER INDICATOR 5) VIDEO OUTPUT CONNECTOR 4 CONNECTIONS 1) POWER INPUT TERMINAL AC Power Cord - This power cord accepts a 100-240V ~ 50Hz +/- 1Hz AC 100-240V 2) VIDEO OUT CONNECTOR BNC : This BNC connector provides a 1.0Vp-p/75 ohms composite video Signal. 5 CONTENTS OF PACKAGE Installation of the camera must be performed by qualified service personnel in accordance with all local and national electrical and mechanical codes. Carefully remove the color camera and its accessories from the carton and verify that they were not damaged in shipment. The contents of the package includes: 1. Color CCD camera 2. Mini-DIN connector (for video-or dc-type auto-iris lens) 3. This Manual MANUAL IRIS LENS ADJUSTMENT When using a manual iris lens, turn the iris ring on the lens to the OPEN position and adjust the manual iris for the appropriate range. Adjust during the brightest conditions, opening the lens to the minimum f-stop yielding a good picture under the brightest scene conditions. Do not saturate the picture. The manual iris is used in indoor applications where lighting from windows can considerably affect the light level of the room. 6 VIDEO AUTO IRIS INSTALLATION & ADJUSTMENT The camera supports video-type auto iris lenses which adjust to changing light levels. Perform the following steps to install and adjust a video-type auto iris lens. 1. If necessary, solder the lens control wires to the connector supplied with The camera. Connector Cover Rib Pin 3 Automatic Iris Lens Pin 1 Heat Pin 4 Shrinkable Tubes Iris Control Pin 2 Cable Connector PIN NAME WIRE COLOR 1 Voltage + 2 Open Red _ 3 Video White 4 Ground Black 2. Attach the video-type auto iris lens to the lens mount on the front of the camera. 3. IMPORTANT: The minimum Plug the connector from the lens into the auto iris jack on the side of the camera. The connector is polarized and can only be inserted into the jack one way. 4. Apply power to the camera. 5. Set the E/I dip switch (rear side on the camera) to OFF position. 6. Set the A/I dip switch (rear side on the camera) to VIDEO position. 7. Adjust the focus ring on the lens for an optimum picture. If a picture is not Visible, set the lens for proper exposure by adjusting the ALC (Automatic Level Control) and the level on the lens. The ALC setting can range between AVG (average) or PK (peak). A midrange setting is appropriate for most applications. 7 For ALC adjustments: AVG To slow the reaction of the lens to changing light, set the range to the AVG setting to average the video level from the camera. Use when there are bright spots in the picture such as lights or glare from the sun. PK To increase the speed of the lens reaction to the changing light, set the lens adjustment to PK so the lens will adjust to the brightest or peak object in the video. Use this setting if you want to see the brightest object and not the background objects. For Level adjustments: Adjust the level control for the best picture during the day. A night adjustment may not provide the proper setting for controlling the light during the day. 8. Set the back focus of the camera before the final adjustment of the video level. 9. If the auto iris has a gain adjustment and the picture oscillates between open and closed under bright lights, slowly turn the gain adjustment counter clockwise until the oscillating stops. Increase the light getting to The camera by adjusting the level control and re-adjusting the gain control. DC AUTO IRIS LENS INSTALLATION & ADJUSTMENT The camera supports DC-type auto iris lenses. Perform the following steps to install and adjust a DC-type auto iris lens. 1. Solder the lens control wires to the connector supplied with the camera. Connector Cover Rib Pin 3 Automatic Iris Lens Pin 1 Heat Pin 4 Shrinkable Tubes Iris Control Pin 2 Cable Connector 8 PIN NAME WIRE COLOR 1 Damp Coil - Blue 2 Damp Coil + Red 3 Drive Coil + White 4 Drive Coil - Green side 4. Apply power to the camera. 5. Set the E/I dip switch (rear side on the camera) to OFF position. 6. Set the A/I dip switch (rear side on the camera) to DC position. 7. Adjust the auto iris lens for an optimum picture using the LEVEL volume on the rear side of the camera. 9 BACK FOCUS ADJUSTMENT For best results, perform back focus adjustments at night or while using a #6 or #8 welder's glass in front of the lens. The focus of the camera will change slightly if the camera iris was adjusted on a light scene, then changes to a dark scene. However, the camera will remain in focus if the iris was focused on a dark scene and the scene lightens. 1. The lens should be mounted on the camera before applying power. 2. If a picture is visible, focus on the picture. If the picture is not visible, open the iris on the lens. Open the lens as wide as possible by placing the welder's glass in front of the lens and forcing the lens to automatically open. 3. When the iris is open to the widest point, re-adjust the focus for clear picture. If a clear picture is not possible, set the focus ring to midrange. 4. Loosen the focus adjusting fixing screw. 5. Adjust the back focus ring for a clear picture. 6. Tighten the focus adjusting fixing screw. 7. Fine tune the focus with the focus ring on the lens. 8. Remove the welder's glass from in front of the lens. 9. Adjust the iris of the lens for the best picture quality. 10 ZOOM LENS BACK FOCUS ADJUSTMENT The objective of back focusing a zoom lens is similar to that of a fixed focal length camera except the back focus is also adjusted to maintain the focus when "zooming" the lens in and out on a scene. 1. Choose an object at the farthest range set for viewing with a zoom lens. 2. Make sure the iris of the lens is wide open. Do this by adjusting the camera at night or use a welders glass in front of the lens. 3. Adjust the focus to the stop on the far range. 4. Adjust the zoom on the lens to obtain the widest picture. 5. Loosen the focus adjusting fixing screw. 6. Adjust the back focus ring for the clearest picture. 7. Tighten the focus adjusting fixing screw. 8. Adjust the zoom on the lens to the far telephoto position. 9. Adjust the back focus ring for the clearest picture. 10. Adjust the zoom on the lens back to the widest picture. 11. Loosen the focus adjusting fixing screw. 12. Re-adjust the back focus for the clearest picture. 13. Tighten the focus adjusting fixing screw. 14. Repeat the previous steps as necessary to maintain a clear picture Throughout the entire zoom range. 11 TROUBLESHOOTING AND MAINTENANCE TROUBLESHOOTING If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information. AREA TO CHECK PROBLEM No video 1. Verify power is applied to all pieces of the equipment in the system. The camera LED should be ON. 2. Verity that the video cables are connected correctly. 3. Verity that the lens cap has been removed from the lens and the iris of the lens is open. Video but no control Power down the system for one minute then re-apply power. Dark Video 1. Adjust iris. 2. Check A/I connections. PREVENTIVE MAINTENANCE Preventive maintenance allows detection and correction of minor that faults before they become serious and cause equipment failure. Every three-month, perform the following maintenance. 1. Inspect all connection cables for deterioration or other damage. 2. Clean components with a clean damp cloth. 3. Verify that all the mounting hardware is secure. 12 SPECIFICATIONS MODEL Power General Connector & etc. Power source Power consumption Image sensor Total pixels Scanning system Scanning frequency Sync. system Electronic shutter Resolution True D&N (NTSC) (PAL) 100 - 240V 3.5 Watts Digital D/N (NTSC) (PAL) 10% 3.0 Watts NTSC : 811(H) x 508(V) / PAL : 795(H) x 596(V) 2:1 interlace NTSC : 15.734KHz(H) x 59.94Hz(V) / PAL : 15.625KHz(H) x 50Hz(V) Internal NTSC : 1/60 ~ 1/100,000 sec. / PAL : 1/50 ~ 1/100,000 sec. 540 TV Lines Color ( 0.25 Lux) / BW(0.01Lux) Color ( 0.25 Lux) Min. illumination @ F1.2, 50 IRE @ F1.2, 50 IRE 1.0 Vp-p (75ohm, composite) Video output More than 50dB (AGC OFF) S/N ratio Dip switch Camera Control E/I F ON / OFF U Flickerless ON / OFF N BLC ON / OFF C AGC ON / OFF T Day/Night Auto / Color Fix I Auto iris lens DC / VIDEO O N White Balance ATW Fixed AC Power Cord Power input Video output BNC connector 4-Pin mini din jack (standard connection) Auto iris output Lens mount C/CS mount (Selected through back focus) Mounting hole 1/4''-20 UNC (top or bottom) Operating temperature +50 Operating humidity 0 ~ 96% (non-condencing) 66 (W) x 56 (H) x 120 (D)mm External dimension 430g 445g Weight 13 540TV Lines Super High Resolution Color Camera PRINTED IN KOREA 50302433A
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021