Dell | S4810-ON | Installation guide | Dell S4810-ON Installation guide

Dell Neworking S4810–Open Networking
(ON) Installation Guide
April 2014
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and
intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other
jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.
2014 - 04
Rev. A00
Contents
1 About this Guide........................................................................................................ 5
Information Symbols............................................................................................................................. 5
Related Documents...............................................................................................................................6
2 The S4810–ON System............................................................................................7
Introduction........................................................................................................................................... 7
Orderable S4810–ON Components...............................................................................................8
Prerequisite............................................................................................................................................8
Features................................................................................................................................................. 9
Ports....................................................................................................................................................... 9
System Status.........................................................................................................................................9
LED Displays.....................................................................................................................................9
3 Site Preparations......................................................................................................11
Site Selection........................................................................................................................................11
Cabinet Placement...............................................................................................................................11
Rack Mounting.....................................................................................................................................12
Grounding (Optional).......................................................................................................................... 12
Fans and Airflow.................................................................................................................................. 12
Power................................................................................................................................................... 12
Storing Components........................................................................................................................... 13
4 Install the S4810–ON............................................................................................ 15
Installing the S4810–ON Chassis in a Rack or Cabinet..................................................................... 15
Attaching the Mounting Brackets into a Two-Post Rack or Cabinet.......................................... 15
Installing the System into a Two-Post Rack or Cabinet...............................................................16
Attaching the Mounting Brackets into a Four-Post Rack or Cabinet.......................................... 17
Installing the System into a Four-Post Rack or Cabinet.............................................................. 18
Attaching the Ground Cable............................................................................................................... 19
Installing the SFP+ and QSFP+ Optics............................................................................................... 20
Remove the SFP+ and QSFP+ Optics...........................................................................................21
Splitting QSFP+ Ports to SFP+ Ports...................................................................................................21
Supply Power and Power Up the System........................................................................................... 21
AC Power....................................................................................................................................... 21
After Installing the S4810–ON............................................................................................................22
5 Power Supplies........................................................................................................ 23
Components........................................................................................................................................23
Installing an AC Power Supply............................................................................................................24
Replacing an AC Power Supply.......................................................................................................... 25
6 Fans............................................................................................................................ 27
Components........................................................................................................................................27
Installing a Fan Module....................................................................................................................... 28
Replacing a Fan Module......................................................................................................................28
7 Console Ports........................................................................................................... 31
Accessing the RJ-45 Console Port (RS-232)......................................................................................31
Access the RJ-45 Console Port with a DB-9 Adapter.......................................................................32
8 Specifications.......................................................................................................... 33
Chassis Physical Design...................................................................................................................... 33
IEEE Standards...............................................................................................................................34
Agency Compliance............................................................................................................................34
USA Federal Communications Commission (FCC) Statement....................................................34
European Union EMC Directive Conformance Statement..........................................................34
Japan: VCCI Compliance for Class A Equipment........................................................................ 35
Korean Certification of Compliance.............................................................................................35
Safety Standards and Compliance Agency Certifications........................................................... 36
Electromagnetic Compatibility (EMC).......................................................................................... 36
Product Recycling and Disposal................................................................................................... 36
Removing the SD Card.................................................................................................................. 37
Replacing the Battery on the S4810–ON.....................................................................................38
9 Technical Support.................................................................................................. 43
The iSupport Website..........................................................................................................................43
Accessing iSupport Services......................................................................................................... 43
Contacting the Technical Assistance Center.....................................................................................43
Requesting a Hardware Replacement................................................................................................44
About this Guide
1
This guide provides site preparation recommendations, step-by-step procedures for rack mounting and
desk mounting, inserting optional modules, and connecting to a power source.
.
CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist straps when
handling this equipment.
WARNING: Only trained and qualified personnel can install this equipment. Read this guide
before you install and power up this equipment. This equipment contains two power cords.
Disconnect both power cords before servicing.
WARNING: This equipment contains optical transceivers, which comply with the limits of Class 1
laser radiation.
WARNING: When no cable is connected, visible and invisible laser radiation may be emitted from
the aperture of the optical transceiver ports. Avoid exposure to laser radiation and do not stare
into open apertures.
Information Symbols
This book uses the following information symbols:
NOTE: The Note icon signals important operational information.
CAUTION: The Caution icon signals information about situations that could result in equipment
damage or loss of data.
WARNING: The Warning icon signals information about hardware handling that could result in
injury.
WARNING: The ESD Warning icon requires that you take electrostatic precautions when handling
the device.
About this Guide
5
Related Documents
For more information about the S4810–ON system, refer to the Dell Networking S4810–Open
Networking (ON) Getting Started Guide.
NOTE: For the most recent documentation, visit iSupport: http://www.dell.com/support/mysupport.
6
About this Guide
The S4810–ON System
2
The following sections describe the Dell Networking S4810–ON system.
Introduction
The Dell Networking S4810–ON platform is a next-generation switch/router designed to meet the
requirements for distributed data center cores.
It is a one-rack unit (RU) chassis that supports 48 ports of 10GbE small form-factor pluggable plus (SFP+)
and four quad small form-factor pluggable plus (QSFP+) ports. For system access, the S4810–ON
includes an RS-232/RJ-45 console port and a management port for system access.
The S4810–ON input/output (I/O) side (shown in the following illustration) contains the 48 ports of
10GbE and four uplink ports of 40GbE QSFP+ autosensing ports and management ports.
Figure 1. S4810–ON I/O-Side View
1.
System LEDs
2.
RS-232/RJ-45 Console Port
3.
Management (Ethernet) Port
4.
40GE QSFP+ Ports
5.
10GE SFP+ Ports
The S4810–ON power supply unit (PSU) side (shown in the following illustration) contains the PSU and
fan modules.
The S4810–ON System
7
Figure 2. S4810–ON PSU-Side View
1.
Mounting Bracket
2.
Fan Module 1
3.
Fan Module 2
4.
Mounting Bracket
5.
Power Supply (PSU2)
6.
Power Supply (PSU1)
7.
Grounding Screw
Orderable S4810–ON Components
You can order the S4810–ON system in several different configurations. You can also order optional
modules and optics separately.
You can order the following supported hardware components.
•
48-port 10G SFP+ with four QSFP+, 40G ports, one AC power supply and two fan subsystems (airflow
from I/O side to power supply side)
•
48-port 10G SFP+ with four QSFP+, 40G ports, one AC power supply and two fan subsystems (airflow
from power supply side to I/O side)
•
S4810–ON Series — Fan with airflow from the I/O side to the PSU side
•
S4810–ON Series — Fan with airflow from the PSU side to the I/O side
•
S4810–ON Series — AC Power supply with airflow from the I/O side to the PSU side
•
S4810–ON Series — AC Power supply with airflow from the PSU side to the I/O side
For a list of supported optics, refer to the S4810–ON data sheet at http://www.dell.com or contact your
Dell Networking representative.
Prerequisite
To successfully install the S4810–ON, ensure that you have the following components.
•
S4810–ON chassis
•
At least one grounded AC power source per chassis
•
Cable to connect the AC power source to the chassis (US power cables included)
•
Mounting brackets for rack installation (included)
•
Screws for rack installation and #1 and #2 Phillips screwdrivers (not included)
8
The S4810–ON System
•
Ground cable (not included, optional)
•
Ground cable screws (included)
•
Copper/fiber cables
Other optional components are:
•
Additional power supply unit
•
Additional fan module
•
Additional mounting brackets (if installing in a four-post rack or cabinet)
Features
The S4810–ON offers the following features.
•
S4810–ON CPU and switch processor
•
Hot-swappable redundant power supply
•
19 inch rack-mountable
•
Standard 1U chassis height
Ports
The S4810–ON offers the following ports.
•
External Serial RS-232 port (RJ45 type)
•
Remote management port
•
48–ports 10GbE and 4–ports 40GbE
•
Universal serial bus (USB)-A port
•
USB-B port
System Status
You can view S4810–ON status information using the light emitting diodes (LEDs).
LED Displays
The S4810–ON includes LED displays on the I/O side of the chassis (shown in the following illustration).
When the S4810–ON powers up or reloads, the PSU LED is solid green. For additional LED information,
refer to your third-party operating software documentation.
The S4810–ON system LEDs are:
•
System status (SYS)
•
Stack Master indicator (MASTER)
•
Fan status (FAN)
•
Power status (PSU)
Additionally, the PSUs and fans have LEDs that indicate their individual status:
•
PSU status
•
Fan tray status
The S4810–ON System
9
•
System
Figure 3. S4810–ON LEDs
1.
SYS
2.
MASTER
3.
FAN
4.
PSU
10
The S4810–ON System
Site Preparations
3
The S4810–ON is suitable for installation as part of a common bond network (CBN).
You can install the system in:
•
network telecommunication facilities
•
data centers
•
other locations where the National Electric Code (NEC) applies
For more information about S4810–ON specifications, refer to Specifications.
NOTE: Install the S4810–ON system into a rack or cabinet before installing any optional
components.
Site Selection
Install Dell Networking equipment in restricted access areas.
A restricted access area is one in which service personnel can only gain access using a special tool, lock,
key or other means of security and access is controlled by the authority responsible for the location.
Ensure that the area where you install your S4810–ON system meets the following safety requirements:
•
Near an adequate power source. Connect the system to the appropriate branch circuit protection as
defined by your local electrical codes.
•
Environmental temperature between 32° to 104°F (from 0° to 40°C).
•
Relative humidity that does not exceed 85 percent noncondensing.
•
In a dry, clean, well-ventilated and temperature-controlled room, away from heat sources such as hot
air vents or direct sunlight.
•
Away from sources of severe electromagnetic noise.
•
Positioned in a rack or cabinet, or on a desktop with adequate space in the front, rear, and sides of the
S4810–ON for proper ventilation and access.
Cabinet Placement
Install the S4810–ON only in indoor cabinets designed for use in a controlled environment.
Do not install the S4810–ON in outside plant cabinets. For cabinet placement requirements, refer to Site
Selection.
The cabinet must be a minimum cabinet size. Airflow must be according to the Electronic Industries
Alliance (EIA) standard. Ensure that there is a minimum of 5 inches (12.7 cm) between the intake and
exhaust vents and the cabinet wall.
Site Preparations
11
Rack Mounting
When you prepare your equipment rack, ensure that the rack is earth ground.
Ground the equipment rack to the same ground point the power service in your area uses. The ground
path must be permanent.
Grounding (Optional)
Use the S4810–ON in a common bond network (CBN).
Connect the grounding cables as described in Install the S4810-ON.
Fans and Airflow
The S4810–ON fans support two airflow options.
Be sure to order the fans suitable to support your site’s ventilation. Use a single type of airflow fan in your
system. Do not mix reverse and normal airflows in a single S4810–ON chassis.
•
Normal — airflow is from the I/O panel to the power supply. The grab-handle is labeled Exhaust.
•
Reversed — airflow is from the power supply to the I/O panel. The grab-handle is labeled Intake.
For proper ventilation, position the S4810–ON in an equipment rack (or cabinet) with a minimum of 5
inches (12.7 cm) of clearance around the exhaust vents. When you install two S4810–ON systems near
each other, position the two chassis at least 5 inches (12.7 cm) apart to permit proper airflow. The
acceptable ambient temperature ranges are listed in Specifications.
The fan speed increases and decreases automatically based on the system’s state and temperature. The
switch never intentionally turns off the fans.
Power
To connect the chassis to the applicable power source, use the appropriate power cord with the S4810–
ON. An AC power cord is included with the system.
When installing AC systems, follow the requirements of the National Electrical Code, ANSI/NFPA 70
where applicable.
The system is powered-up as soon as the power cord is connected between the system and the power
source.
CAUTION: Always disconnect the power cable before you service the power supply slots.
CAUTION: Use the power supply cord as the main disconnect device on the AC system. Ensure
that the socket-outlet is located/installed near the equipment and is easily accessible.
12
Site Preparations
Storing Components
If you do not install your S4810–ON and components immediately, Dell Networking recommends
properly storing the system and all optional components until you are ready to install them.
WARNING: ESD damage can occur when components are mishandled. Always wear an ESDpreventive wrist or heel ground strap when handling the S4810–ON and its accessories. After you
remove the original packaging, place the S4810–ON and its components on an antistatic surface.
Follow these storage guidelines:
•
Storage temperature must remain constant ranging from -40° to 158°F (from -40°C to 70°C).
•
Store on a dry surface or floor, away from direct sunlight, heat, and air conditioning ducts.
•
Store in a dust-free environment.
Site Preparations
13
14
Install the S4810–ON
4
To install the S4810–ON system, Dell Networking recommends completing the installation procedures in
the order presented in this chapter.
Always handle the S4810–ON and its components with care. Avoid dropping the system or its field
replaceable units (FRUs).
This chapter describes the installation procedures as follows:
1.
Installing the S4810–ON Chassis in a Rack or Cabinet
a.
Attaching the Mounting Brackets into a Two-Post Rack or Cabinet
b.
Installing the System into a Two-Post Rack or Cabinet
c.
Attaching the Mounting Brackets into a Four-Post Rack or Cabinet
d.
Installing the System into a Four-Post Rack or Cabinet
2.
Attaching the Ground Cable
3.
Installing the SFP+ and QSFP+ Optics
4.
Splitting QSFP+ Ports to SFP+ Ports
5.
Supply Power and Power Up the System
6.
After Installing the S4810-ON
WARNING: ESD damage can occur if components are mishandled. Always wear an ESDpreventive wrist or heel ground strap when handling the S4810–ON and its components. As with
all electrical devices of this type, take all the necessary safety precautions to prevent injury when
installing this system.
Installing the S4810–ON Chassis in a Rack or Cabinet
The following sections describe how to install the S4810–ON in a rack or cabinet.
Attaching the Mounting Brackets into a Two-Post Rack or Cabinet
The S4810–ON ships with mounting brackets (rack ears) and the required screws for a two-post rack or
cabinet installation. The brackets are sent in a package with the system.
NOTE: Dell Networking recommends attaching the brackets at the power supply unit (PSU) side.
This set up provides the greatest weight support for the chassis in the rack or cabinet.
Install the S4810–ON
15
To attach the brackets to the system, follow these steps.
1.
Take the brackets and screws out of their packaging.
2.
Attach the brackets to the PSU sides of the system using four screws for each bracket. Attach the
bracket so that the “ear” is parallel to the PSU and the outside of the system.
Figure 4. Attaching Mounting Brackets into a Two-Post Rack or Cabinet
1.
3.
5.
View from the chassis I/O side
Screws
Connect to the Rack or Cabinet (ears)
2.
4.
6.
Connect to the Rack or Cabinet (ears)
Screws
Power Supply
Installing the System into a Two-Post Rack or Cabinet
Ensure that there is adequate clearance surrounding the rack or within the cabinet to permit access and
airflow.
To install a system into a two-post 19-inch equipment rack using the already attached mounting
brackets, follow these steps.
16
Install the S4810–ON
NOTE: Dell Networking recommends using one person to hold the S4810–ON chassis in place
while another person attaches the brackets to the posts.
Attach the bracket “ears” to the rack or cabinet posts using the two screws for each bracket. Ensure
the screws are tightened firmly.
Figure 5. Installing the System into a Two-Post Rack or Cabinet
1.
3.
PSU1
Rack Mounting Ears
2.
4.
PSU2
Rack or Cabinet Post
Attaching the Mounting Brackets into a Four-Post Rack or Cabinet
The S4810–ON ships with mounting brackets (rack ears) and the required screws for a two-post rack or
cabinet installation.
To install the S4810–ON in a four-post rack or cabinet, you must order additional brackets separately.
Use the brackets included with the S4810–ON on the I/O side of system and use the brackets you
ordered separately on the PSU side of the system.
Unlike the two-post installation, the four-post installation requires attaching brackets to the rack prior to
installing the system.
To attach the brackets to the rack or cabinet, follow these steps.
1.
Ensure that there is adequate clearance surrounding the rack or within the cabinet to permit access
and airflow.
2.
Take the brackets and screws out of their packaging.
Install the S4810–ON
17
3.
Attach the brackets to the PSU sides of the chassis using four screws for each bracket. Attach the
bracket so that the “ear” is parallel to the PSU and the outside of the chassis.
Figure 6. Attaching the Mounting Brackets into a Four-Post Rack or Cabinet
1.
3.
5.
View from the chassis I/O side
Screws
Connect to the rack or cabinet (ears)
2.
4.
6.
Connect to the rack or cabinet
Screws
Power Supply
4.
Attach the long bracket to each side of the chassis using the provided countersink screws. Use two
screws on each side of the chassis.
5.
Install the rack mount ears into the I/O-facing posts using rack mount screws (not included with the
system).
NOTE: Mount the rack mount ears so that the system is level when fully installed.
6.
Using the provided pan head screws, attach the rack ears on the I/O facing posts to the long bracket
(attached to the system). To secure, tighten the pan head screws.
Installing the System into a Four-Post Rack or Cabinet
To install a system into a four-post equipment rack using the already attached mounting brackets, follow
these steps.
1.
Ensure that there is adequate clearance surrounding the rack or within the cabinet to permit access
and airflow.
2.
Install the system into the rack. Ensure the long brackets dock into the previously installed rack ears.
18
Install the S4810–ON
3.
Fasten the system to the PSU-facing posts using rack mount screws (not included with the system).
Figure 7. Installing the System into a Four-Post Rack or Cabinet
1.
3.
5.
4.
I/O Side
Long Brackets
PSU Side
2.
4.
Rack Ears
Rack Ears
Use the provided pan head screws to attach the rack ears on the I/O-facing posts to the long bracket
previously attached to the system. Tighten the pan head screws to secure the system.
Attaching the Ground Cable
To attach the ground cable to the chassis, use a single M4x0.7 screw.
The cable itself is not included with the S4810–ON. To properly ground the chassis, Dell Networking
recommends using a 6AWG one-hole lug, #10 hole size, 63" spacing (not included in shipping). The onehole lug must be a UL recognized, crimp-type lug.
NOTE: The rack installation “ears” are not suitable for grounding.
CAUTION: Grounding conductors must be made of copper. Do not use aluminum conductors.
To connect the ground cable to the system, follow these steps.
NOTE: Coat the one-hole lug with an anti-oxidant compound prior to crimping. Also, bring any unplated mating surfaces to a shiny finish and coat with an anti-oxidant prior to mating. Plated mating
surfaces must be clean and free from contamination.
1.
Take the one M4x0.7 screw from the package.
2.
Cut the cable to the desired length. The cable length must facilitate proper operation of the fault
interrupt circuits. Dell Networking recommends using the shortest cable route allowable.
Install the S4810–ON
19
3.
Attach the one-hole lug to the chassis using the supplied 10-32 screw with the captive internal tooth
lock washer. Torque the screw to 20 in-lbs.
Figure 8. Attaching the Ground Cable
a.
4.
Lug hole
b. Ground Screw
Attach the other end of the ground cable to a suitable ground point. The rack installation ears are not
a suitable grounding point.
Installing the SFP+ and QSFP+ Optics
The S4810–ON has 48 SFP+ optical ports and four QSFP+ optical ports.
WARNING: ESD damage can occur if components are mishandled. Always wear an ESDpreventive wrist or heel ground strap when handling the S4810–ON and its components.
WARNING: When working with optical fibers, follow all warning labels and always wear eye
protection. Never look directly into the end of a terminated or unterminated fiber or connector
as it may cause eye damage.
To install SFP+ or QSFP+ optics into an open port, follow these steps:
1.
Position the optic so it is in the correct position. The optic has a key that prevents it from being
inserted incorrectly.
2.
Insert the optic into the port until it gently snaps into place.
NOTE: Both rows of QSFP+ ports require that the 40G optics be inserted with the tabs facing
up.
20
Install the S4810–ON
Remove the SFP+ and QSFP+ Optics
Remove an optic by pushing the tab on the optic and sliding the optic from the port.
When removing optics with direct attach cables (DACs) from the port, pull the release tab firmly and
steadily. Prior to pulling the release tab, you may need to gently push the optic into the port to ensure it is
seated properly. Do not jerk or tug repeatedly on the tab.
Splitting QSFP+ Ports to SFP+ Ports
The S4810–ON supports splitting a single 40G QSFP+ port into four 10G ports using one of the
supported breakout cables.
Supply Power and Power Up the System
Supply power to the S4810–ON after it is mounted in a rack or cabinet.
Dell Networking recommends re-inspecting your system prior to powering up. Verify that:
•
the equipment is properly secured to the rack and properly grounded.
•
the equipment rack is properly mounted and grounded.
•
the ambient temperature around the unit (which may be higher than the room temperature) is within
the limits specified for the S4810–ON.
•
there is sufficient airflow around the unit.
•
the input circuits are correctly sized for the loads and that you use sufficient over-current protection
devices.
•
all protective covers are in place.
•
blank panels are installed if you do not install optional modules.
NOTE: A US AC power cable is included for powering up an AC power supply. You must order all
other power cables separately.
NOTE: ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist
or heel ground strap when handling the S4810–ON system and its components.
AC Power
To add AC power, connect the power cord plug to each AC power connector. Make sure that the power
cord is secure (as shown in the following illustration).
CAUTION: Ensure that you correctly install the PSU. When correctly installed, the AC power
connector is on the left side of the PSU and the status LED is at the top of the PSU (as shown in
the following illustration).
As soon as the cable is connected between the S4810–ON and the power source, the system is
powered-up; there is no on/off switch.
Install the S4810–ON
21
Figure 9. AC Power Connection
1.
Power Connection
2.
LED
After Installing the S4810–ON
After you have securely installed and powered on the S4810-ON, refer to your ONIE-compatible thirdparty operating system documentation to configure your system.
22
Install the S4810–ON
Power Supplies
5
The S4810–ON supports two hot-swappable power supply units (PSUs) with integrated fans that provide
cooling for the system.
The S4810–ON supports AC power supplies with two air-flow directions (normal and reversed). Two
PSUs are required for full redundancy, but the system can operate with a single PSU.
NOTE: If you use a single PSU, install a blank plate in the other PSU slot. Dell Networking
recommends using power supply 2 (PSU2) as the blank plate slot.
The PSUs are field replaceable. When running with full redundancy (two power supplies installed and
running), you can remove and replace one PSU while the other PSU is running without disrupting traffic.
The power supply LED indicates the power supply status:
•
Off — no power
•
Solid Green — Power supply is present and working
WARNING: ESD damage can occur if components are mishandled. Always wear an ESDpreventive wrist or heel ground strap when handling the S4810–ON and its components.
WARNING: To prevent electrical shock, ensure that the S4810–ON is grounded properly. If you
ground your equipment incorrectly, excessive emissions may result. To ensure that the power
cables meet your local electrical requirements, use a qualified electrician.
Components
The following power supply options are available for the S4810–ON.
•
AC power supply with integrated fan
•
AC power supply with integrated reverse flow fan
Power supply 1 (PSU1) is on the left side of the chassis; power supply 2 (PSU2) is on the right side of the
chassis.
The PSUs in the S4810–ON are field replaceable. When both power supplies are installed and running,
you can remove one power supply without interrupting traffic.
The PSUs are in a single piece with the PSU fans. You can replace the fan trays individually, but you
cannot replace the fans that are attached to the PSUs — if the fans attached to the PSU fail, you must
replace the entire PSU. For fan tray replacement procedures, refer to Fans.
WARNING: Prevent exposure and contact with hazardous voltages. Do not attempt to operate
this system with the safety cover removed.
CAUTION: Remove the power cable from the PSU prior to removing the PSU. Also, do not
connect the power cable before you insert the PSU in the chassis.
NOTE: To comply with the GR-1089 Lightning Criteria for Equipment Interfacing with AC Power
Ports, use an external SPD at the AC input of the router.
Power Supplies
23
Installing an AC Power Supply
To install an AC power supply, follow these steps.
NOTE: The PSU slides into the slot smoothly. Do not force a PSU into a slot as this action may
damage the PSU or the S4810–ON chassis.
NOTE: Ensure that the PSU is correctly installed. When the PSU is correctly installed, the power
connector is on the left side of the PSU and the status LED is at the top of the PSU (refer to the
following illustration).
Figure 10. Installing an AC Power Supply
1.
PSU1
2.
Fan Module
3.
Fan Module
4.
Cable Connector
5.
PSU2
6.
Grab Handle
NOTE: If you use a single PSU, you must install a blank plate in the other PSU slot. Dell Networking
recommends using power supply 2 (PSU2) as the blank plate slot.
1.
Take the PSU out of the shipping box.
2.
Use the grab handle to slide the PSU into the power supply bay.
3.
Tighten the securing screw on the side of the PSU. Ensure that the PSU is secure.
4.
Attach the power cables.
NOTE: The system powers up as soon as the cables are connected between the power supply
and the power source.
24
Power Supplies
Replacing an AC Power Supply
To replace an AC power supply, follow these steps:
NOTE: The PSU slides into the slot smoothly. Do not force a PSU into a slot as this action may
damage the PSU or the S4810–ON chassis.
NOTE: If a PSU fails, you must completely replace it. There are no field serviceable components in
the PSU. To request a hardware replacement, refer to Technical Support.
NOTE: If you use a single PSU, you must install a blank plate in the other PSU slot. Dell Networking
recommends using power supply 2 (PSU2) as the blank plate slot.
1.
Disconnect the power cable from the PSU.
2.
Use the grab handle to slide the PSU out of the power supply bay.
3.
Use the grab handle on the replacement PSU to slide it into the power supply bay.
4.
Tighten the securing screws on the replacement PSU with a screwdriver. Ensure that the PSU is
secure.
5.
Attach the power cord to the replacement PSU.
The system powers up as soon as the cables are connected between the power supply and the
power source.
Power Supplies
25
26
Fans
6
The S4810–ON comes from the factory with one power supply unit (PSU) and two fan modules installed
in the system.
If two or more fans are installed and running, the fan modules are hot-swappable.
NOTE: To run the system, both slots must have operating fan units. If a module is not installed in
each slot (either as part of the PSU or as an independent fan module), the system shuts down in one
minute.
In addition to the integrated fan/power supply modules, you can order and install fan modules separately.
The S4810–ON supports two airflow direction options. Do not mix airflow types in a chassis; you can use
only a single airflow direction in a chassis.
•
Normal — airflow is from the I/O panel to the PSU
•
Reversed — airflow is from the PSU to the I/O panel
Environmental factors can decrease the amount of time required between fan replacements. Check the
environmental factors regularly. An increase in temperature and/or particulate matter in the air might
affect performance (for example, new equipment installation).
CAUTION: Check the fans at six-month intervals and replace them as necessary. Regularly
monitor the speeds of the cooling fans in order to accurately determine replacement intervals.
Components
The following are the S4810–ON fan components.
•
S4810–ON Fan module
•
S4810–ON Fan module - Reverse flow
Fans
27
Figure 11. S4810–ON Fan Module
1.
PSU1
2.
Fan Module 1
3.
Fan Module 2
4.
Grab Handle
5.
PSU2
Installing a Fan Module
The fan modules in the S4810–ON are field replaceable.
Module slot 0 is on the left side of the chassis; module slot 1 is on the right side of the chassis.
CAUTION: DO NOT mix airflow directions. Both fans must use the same airflow direction (reverse
or normal).
To install a fan module, follow these steps.
1.
Take the fan module out of the shipping box.
2.
Use the grab handle to slide the fan module into the bay.
3.
Tighten the securing screws on the sides of the fan module.
Replacing a Fan Module
To replace a fan module, follow these steps.
1.
Loosen the securing screws on the sides of the fan module.
CAUTION: You must complete steps 2 and 3 within one minute or the system powers down.
2.
Use the grab handle to slide the fan module out of the bay.
3.
Use the grab handle on the replacement module to slide it into the bay.
28
Fans
4.
Fans
Tighten the captive screws on the replacement module with a screwdriver. Ensure that the module is
secure.
29
30
Console Ports
7
You can access the S4810–ON directly through the console port at the input/output (I/O) side of the
system.
Accessing the RJ-45 Console Port (RS-232)
The RS-232/RJ-45 console port is labeled on the upper-right-hand side of the S8410–ON chassis (the
I/O side) (as shown in the following illustration).
NOTE: Before starting this procedure, be sure that you have a terminal emulation program already
installed on your PC.
Figure 12. S4810–ON Serial Console Port Connector
1.
RJ-45 Console Port
The following table lists the console port pinout assignments.
To access the console port, follow these steps.
1.
Install an RJ-45 copper cable into the console port. Use a rollover cable to connect the S4810–ON
console port to a terminal server.
2.
Connect the other end of the cable to the dumb terminal emulator (DTE) server.
3.
Keep the default terminal settings on the console as follows:
– 115200 baud rate
– No parity
– 8 data bits
– 1 stop bit
– No flow control
Console Ports
31
Access the RJ-45 Console Port with a DB-9 Adapter
If the DTE has a DB-9 interface, you can connect to the console using an RJ-45 to DB-9 adapter along
with the RJ-45 rollover cable.
The following table lists the pin assignments.
Table 1. Pin Assignments Between the Console and a DTE Terminal Server
Console Port
RJ-45 to RJ-45
Rollover Cable
RJ-45 to RJ-45
Rollover Cable
RJ-45 to DB-9
Adapter
Terminal Server
Device
Signal
RJ-45 Pinout
RJ-45 Pinout
DB-9 Pin
Signal
RTS
1
8
8
CTS
NC
2
7
6
DSR
TxD
3
6
2
RxD
GND
4
5
5
GND
GND
5
4
5
GND
RxD
6
3
3
TxD
NC
7
2
4
DTR
CTS
8
1
7
RTS
32
Console Ports
8
Specifications
This chapter lists the S4810–ON specifications.
Chassis Physical Design
Table 2. Chassis Physical Design
Parameter
Specifications
Height
1.73 inches (4.4 cm)
Width
17.32 inches (44.0 cm)
Depth
18.11 inches (46 cm)
Chassis weight with factory-installed components
14.39 pounds (approx.) (6.54 kg)
Rack clearance required
Front: 5-inches (12.7 cm)
Rear: 5-inches (12.7 cm)
Thermal dissipation
1194 BTH/h
Power consumption
250 Watts (nominal)
350 Watts (maximum)
Table 3. Environmental Parameters
Parameter
Specifications
Temperature
32° to 104°F (0° to 40°C)
Storage Temperature
-40° to 158°F (-40° to 70°C)
Maximum altitude
No performance degradation to 10,000 feet (3,048
meters)
Relative humidity
10 to 85% non-condensing
Shock
MIL-STD-810
Table 4. AC Power Requirements
Parameter
Specifications
Nominal input voltage
100 to 240 VAC, 47-63 Hz
Maximum AC power supply input current
4A @ 100/120VAC
2A @ 200/240 VAC
Maximum system power input
350 W
Specifications
33
IEEE Standards
The S4810–ON complies with the following IEEE standards.
•
•
•
•
•
802.3ab Gigabit Ethernet (1000BASE-T)
802.3ae 10 Gigabit Ethernet (10GBASE-X)
802.3ba 40 Gigabit Ethernet (40GBase-SR4, 40GBase-CR4) on optical ports
802.3u Fast Ethernet (100BASE-TX)
802.3z Gigabit Ethernet (1000BASE-X)
Agency Compliance
The S4810–ON is designed to comply with the following safety and agency requirements.
USA Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC rules. These limits are designated to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy. If it is not installed and used in accordance to the
instructions, it may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case users will be required to take
whatever measures necessary to correct the interference at their own expense.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. Dell Networking is not responsible for any radio or television interference caused by using other
than recommended cables and connectors or by unauthorized changes or modifications in the
equipment. Unauthorized changes or modification could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Figure 13. Canadian Department of Communication Statement
European Union EMC Directive Conformance Statement
This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on
the approximation of the laws of the Member States relating to electromagnetic compatibility. Dell
Networking can not accept responsibility for any failure to satisfy the protection requirements resulting
from a non-recommended modification of this product, including the fitting of non-Dell Networking
option cards.
This product has been tested and found to comply with the limits for Class A Information Technology
Equipment according to CISPR 22/European Standard EN 55022. The limits for Class A equipment were
34
Specifications
derived for commercial and industrial environments to provide reasonable protection against interference
with licensed communication equipment.
WARNING: This is a Class A product. In a domestic environment, this device may cause radio
interference, in which case, you may be required to take adequate measures.
European Community Contact
Dell Networking, EMEA - Central
Dahlienweg 19
66265 Heusweiler
Germany
http://www.force10networks.com/german/
Tel: +49 172 6802630
Email: EMEA Central Sales
Japan: VCCI Compliance for Class A Equipment
WARNING: Use the AC power cords with Dell Networking equipment only. Do not use Dell
Networking AC power cords with any unauthorized hardware.
This is Class A product based on the standard of the Voluntary Control Council For Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
Korean Certification of Compliance
Specifications
35
Korean Package Label
Safety Standards and Compliance Agency Certifications
•
CUS UL 60950-1, 2nd Edition
•
CSA 60950-1-03, 2nd Edition
•
EN 60950-1, 2nd Edition
•
EN 60825-1, 1st Edition
•
EN 60825-1 Safety of Laser Products—Part 1: Equipment Classification Requirements and User’s
Guide
•
EN 60825-2 Safety of Laser Products—Part 2: Safety of Optical Fibre Communication Systems
•
FDA Regulation 21CFR 1040.10 and 1040.11
•
IEC 60950-1, 2nd Ed, including all National Deviations and Group Differences
Electromagnetic Compatibility (EMC)
Emissions
•
International: CISPR 22: 2006, Class A
•
Australia/New Zealand: AS/NZS CISPR 22:2009, Class A
•
Canada: ICES-003, Issue-4, Class A
•
Europe: EN55022 2006 (CISPR 22: 2006), Class A
•
Japan: VCCI V-3/2011.04 Class A
•
USA: FCC CFR47 Part 15, Subpart B, Class A
Immunity
•
EN 300 386 v1.5.1:2010 EMC for Network Equipment
•
EN55022 2006, Class A
•
EN 55024 1998 + A1: 2001 + A2: 2003
•
EN 61000-3-2 Harmonic Current Emissions
•
EN 61000-3-3 Voltage Fluctuations and Flicker
•
EN 61000-4-2 ESD
•
EN 61000-4-3 Radiated Immunity
•
EN 61000-4-4 EFT
•
EN 61000-4-5 Surge
•
EN 61000-4-6 Low Frequency Conducted Immunity
Product Recycling and Disposal
You must recycle or discard this system according to applicable local and national regulations. Dell
Networking encourages owners of information technology (IT) equipment to responsibly recycle their
equipment when it is no longer needed. Dell Networking offers a variety of product return programs and
services in several countries to assist equipment owners in recycling their IT products.
36
Specifications
Waste Electrical and Electronic Equipment (WEEE) Directive for Recovery, Recycle and
Reuse of IT and Telecommunications Products
Dell Networking switches are labeled in accordance with European Directive 2002/96/EC concerning
waste electrical and electronic equipment (WEEE). The Directive determines the framework for the return
and recycling of used appliances as applicable throughout the European Union. This label is applied to
various products to indicate that the product is not to be thrown away, but rather reclaimed upon end of
life per this Directive.
Figure 14. The European WEEE Symbol
In accordance with the European WEEE Directive, electrical and electronic equipment (EEE) is to be
collected separately and to be reused, recycled, or recovered at end of life. Users of EEE with the WEEE
marking per Annex IV of the WEEE Directive, as shown above, must not dispose of end of life EEE as
unsorted municipal waste, but use the collection framework available to customers for the return,
recycling and recovery of WEEE. Customer participation is important to minimize any potential effects of
EEE on the environment and human health due to the potential presence of hazardous substances in
EEE.
Dell Networking products, which fall within the scope of the WEEE, are labeled with the crossed-out
wheelie-bin symbol, as shown above, as required by WEEE.
For information on Dell Networking product recycling offerings, see the WEEE Recycling instructions on
iSupport at: https://www.force10networks.com/CSPortal20/Support/WEEEandRecycling.pdf. For more
information, contact the Dell Networking Technical Assistance Center (TAC) (refer to Contacting the
Technical Assistance Center.
Removing the SD Card
To support high security environments, you can remove and re-install the SD card.
Dell Networking recommends removing the SD card only when necessary. Only authorized personnel
should remove the SD card.
CAUTION: Only remove the SD card to support high security operations and after discussions
with Dell Networking Technical Support or your Dell Networking representative.
To open the case and remove the SD card, follow these steps.
1.
Remove the small phillips screws that connect the top of the SD card to the body. The screws are
located on the top and the sides of the chassis.
2.
Slide the top backwards until its front flange slides free of the faceplate then lift it off.
3.
Gently push the SD card to release it from the slot.
Specifications
37
4.
Remove the card.
Figure 15. Illustration of removing the SD Card
Replacing the Battery on the S4810–ON
The lithium battery is not field replaceable.
Only authorized personal should remove and replace the battery. If the battery requires replacement,
contact Dell Networking Technical Support.
WARNING: ESD damage can occur if components are mishandled. Always wear an ESDpreventive wrist or heel ground strap when handling the S4810–ON and its components. As with
all electrical devices of this type, take all the necessary safety precautions to prevent injury when
installing this system.
38
Specifications
To open the case, follow these steps.
1.
Remove the small Phillips screws that connect the top of the case to the body. There are three
screws evenly spaced across the rear and three screws evenly spaced along each side of the case.
2.
Slide the top backwards until its front flange slides free of the faceplate then lift it off.
Figure 16. Battery Location
Specifications
39
Figure 17. Close-Up View of the Battery
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC
concerning batteries and accumulators and waste batteries and accumulators. The Directive determines
the framework for the return and recycling of used batteries and accumulators as applicable throughout
the European Union. This label is applied to various batteries to indicate that the battery is not to be
thrown away, but rather reclaimed upon end of life per this Directive.
In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to
indicate that they are to be collected separately and recycled at end of life. The label on the battery may
also include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury and
Cd for cadmium). Users of batteries and accumulators must not dispose of batteries and accumulators as
unsorted municipal waste, but use the collection framework available to customers for the return,
recycling and treatment of batteries and accumulators.
Customer participation is important to minimize any potential effects of batteries and accumulators on
the environment and human health due to the potential presence of hazardous substances. For proper
collection and treatment, contact your local Dell Networking representative.
40
Specifications
Figure 18. The European WEEE Symbol
For California:
•
Perchlorate Material — Special handling may apply.
•
Refer to http://www.dtsc.ca.gov/hazardouswaste/perchlorate
The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5
Chapter 33. Best Management Practices for Perchlorate Materials.
Specifications
41
42
Technical Support
9
This chapter contains the following sections:
•
The iSupport Website
•
Contacting the Technical Assistance Center
•
Requesting a Hardware Replacement
The iSupport Website
iSupport provides a range of documents and tools to assist you with effectively using Dell Networking
equipment and mitigating the impact of network outages.
Through iSupport you can obtain technical information regarding Dell Networking products, access to
software upgrades and patches, and open and manage your Technical Assistance Center (TAC) cases.
Dell Networking iSupport provides integrated, secure access to these services.
Accessing iSupport Services
The URL for iSupport is http://www.dell.com/support. You must have a userid and password to access
iSupport services. If you do not have a userid and password, you can request these at the website.
To request a userid, password, and iSupport services, follow these steps.
1.
On the Dell Networking Support page, click the Account Request link.
2.
Fill out the User Account Request form and click Send. You will receive your userid and password by
email.
3.
To access iSupport services, click the LOGIN link and enter your userid and password.
Contacting the Technical Assistance Center
How to
Contact Dell
Networking
TAC
Information to
Submit When
Opening a
Support Case
Technical Support
Log in to iSupport at http://www.dell.com/support and select the Service Request
tab.
•
Your name, company name, phone number, and E-mail address
•
Preferred method of contact
•
Model number
•
Software version number
•
Symptom description
43
Managing Your
Case
Log in to iSupport and select the Service Request tab to view all open cases and
Return Materials Authorizations (RMAs).
Technical
Documentation
Log in to iSupport and select the Documents tab. You can access this page without
logging in using the Documentation link on the iSupport page.
Contact
Information
E-mail: Dell-Force10_Technical_Support@Dell.com
Web: http://www.dell.com/support
Telephone:
•
US and Canada: 1.866.965.5800
•
International: +1.408.965.5800
Requesting a Hardware Replacement
To request replacement hardware, follow these steps.
1.
Determine the part number and serial number of the component.
2.
Request an RMA number from TAC by opening a support case. Open a support case by:
– Using the Create Service Request form on the iSupport page (refer to Contacting the Technical
Assistance Center).
– Contacting Dell Networking directly by email or by phone (refer to Contacting the Technical
Assistance Center). Provide the following information when using email or phone:
44
*
Part number, description, and serial number of the component.
*
Your name, organization name, telephone number, fax number, and email address.
*
Shipping address for the replacement component, including a contact name, phone number,
and email address.
*
A description of the failure, including log messages.
Technical Support
Download PDF