Worcester | 35CDI II | Technical data | Worcester 35CDI II Technical data

BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 28
SEDBUK Band A
Gas Boilers
Useful numbers
Sales
Service
Tel: 01905 752640
Fax: 01905 456445
01905 455394
Tel: 08457 256206
Fax: 01905 757536
Livingston (Scotland)
Fax: 01506 441687
Technical (Pre & Post Sales)
Training
Tel: 08705 266241
Fax: 01905 752741
Tel: 01905 752526
Fax: 01905 752535
Spares
Literature Line
Tel: 01905 752571
Fax: 01905 754620
Tel: 01905 752556
The Worcester
Greenstar CDi Gas-fired
Condensing Combi Boiler Series
Technical and Specification Information
www.worcester-bosch.co.uk
In partnership with
Worcester, Bosch Group is a trading name of BBT Thermotechnology UK Ltd.
This leaflet is accurate at the date of printing, but may be superseded and should be disregarded if specification and/or appearances are changed
in the interest of continued improvement. The statutory rights of the consumer are not not affected.
Part No. 8 716 109 213
Issue B
BBT180
Worcester, Bosch Group
Cotswold Way, Warndon, Worcester, WR4 9SW
Tel: 01905 754624 Fax: 01905 754619 www.worcester-bosch.co.uk
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 2
The Greenstar CDi condensing combi boiler series
Total heating and hot water comfort
It’s often said that you can’t please everybody all of the time – but
the advanced new series of Greenstar CDi condensing combi boilers
from Worcester has so much to offer that it’s already disproving such a
notion.
The Greenstar CDi
combi series
Adjustable hot water control.
User comfort & economy.
Aluminium silicon
heat exchanger.
High efficiency.
Instantly heated hot water.
SEDBUK Band A.
High efficiency.
HE stands for Higher
Efficiency and for
Highly Cost Effective
COMBUSTION
PRODUCTS
22%
COMBUSTION
PRODUCTS
<10%
COMBUSTION
PRODUCTS
COMBUSTION
PRODUCTS
SEASONAL
EFFICIENCY
GROSS
Modulation control.
Energy saving.
Filling link supplied as
standard.
Labour saving.
Anti-cycle control.
Energy saving.
Electronic ignition.
Energy saving.
Built-in frost protection.
Money saving,
economical protection.
Multi-directional fluing.
Siting flexibility.
No ventilation grilles required
for compartment installations.
Money and labour saving.
Fault finding diagnostics &
service modes displayed.
Time saving.
Operational status indicator.
Consumer friendly.
No bypass required.
Labour & money saving.
Pump seizure protection.
Prevents callbacks.
Holiday function.
More economical.
Service mode.
Ease of servicing.
Variable speed pump.
Automatically adjusts to
meet system flow demand
– energy saving.
Condensing in DHW mode.
Energy saving.
Optional mechanical &
digital timeclocks.
Eliminates the need for
external wiring.
Radio frequency controlled
room thermostat.
Eliminates wiring, helps
comply with part L of
Building Regulations and
meets the requirements of
Part P.
Text display option.
Plug-in RF optimising
controls.
Hence SEDBUK Band A ratings for all models in the new Greenstar
CDi condensing range.
Greenstar CDi condensing combi boilers deliver this energy-saving
performance by ingeniously recycling exhaust gases to extract and
re-use the latent heat – a highly efficient use of energy which also
significantly reduces carbon dioxide emissions into the atmosphere.
To all these major benefits you can add yet more: superlative Worcester
quality and reliability; a range of outputs to satisfy the heating demands
of a range of households; and truly exceptional all-round value for
money.
BASED ON
3 BEDROOM
SEMI-DETACHED
HOUSE
65%
SEASONAL
EFFICIENCY
27,140 kWh
924 therms
23,600 kWh
804 therms
19,588 kWh
667 therms
OLD
EXISTING
BOILER
NEW
BOILER
GREENSTAR CDi
IN CONDENSING
MODE
78%
SEASONAL
EFFICIENCY
90.2%
SEASONAL
EFFICIENCY
Intelligent control.
OLD
EXISTING BOILER
Easy to install.
2
NEW
CONVENTIONAL BOILER
GREENSTAR CDi
CONDENSING
COMBI BOILER
The Greenstar CDi series at a glance
25CDi
30CDi
35CDi
40CDi
Output kW Min
7.7kW
7.7kW
7.7kW
8.6kW
to DHW
25kW
30kW
35kW
40kW
10.2 lt/min
12.3 lt/min
14.3 lt/min
16.3 lt/min
Modulating control
Natural gas
LPG
Electronic ignition
Max
Flow rate at 35º
CH temperature control
DHW temperature
control
3
Worcester training
Space saving,
ease of siting.
The Greenstar CDi series accessories After-sales
Compact dimensions.
GROSS
Installation requirements
Allows pre-fabrication
of system.
Greenstar CDi series horizontal fluing options Greenstar CDi series vertical fluing options
Wall mounting jig.
The Greenstar CDi condensing combi system layout Installing the Greenstar CDi Series
The Greenstar CDi condensing
78%
90%
combi boilers have an average
annual efficiency (SEDBUK
value) of over 90%, efficiently
NEW
GREENSTAR CDi
producing heat for your heating
CONVENTIONAL
CONDENSING
BOILER
COMBI BOILER
and/or hot water system. Other
types of boiler achieve around 78% efficiency. Therefore, compared with
a new conventional boiler, Greenstar CDi condensing combi boilers can
cut heating and hot water bills and it’s cheaper to run than an older
boiler.
SEASONAL
EFFICIENCY
The Greenstar CDi condensing combi boiler series The advantages of a combi system
Boiler keep hot facility.
Here is a ground-breaking range of energy-saving boilers which is very
good news for the environment and excellent news for specifiers,
developers, installers and consumers alike.
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 4
The Greenstar CDi condensing combi boiler series
Central heating mode
The advantages of a combi boiler
A combi (or combination boiler) is a compact and
highly efficient unit giving all the heating and hot
water you need, with significant savings on running
and installation costs.
Unlike a conventional heating and hot water system,
a combi boiler system does not store domestic hot
water. It heats water directly from the cold mains –
as you use it. There’s no hot water cylinder, no tank in
the loft (and so less risk of freezing and flooding),
and none of the connecting
pipe work. So you not only
save space, but also reduce
hot water costs – which can
account for up to 60% of a
typical domestic fuel bill.
Cold Water
Storage
Cistern
Feed and
Expansion
Cistern
CONVENTIONAL SYSTEM
LAYOUT
Hot to Baths, Showers
and Basins etc.
Hot
Water
Tank
Motorised
Valve
The Greenstar CDi series of condensing combi boilers is available
with a comprehensive range of easy-to-use controls, ranging from
a simple mechanical timer to a choice of sophisticated radiofrequency digistats. All fascia mounted controls offer simple
plug-in connection to the boiler circuit board.
MT10 mechanical timer
Options
A simple easy-to-operate mechanical
timer with 15 minute switching points
over a 24 hour period. The timer
features a clock face with raised
hands to facilitate setting by visually
impaired users.
Fluing
Pump
The Greenstar CDi series features 2 different sizes of
multi-directional RSF flue systems, 100mm or 125mm.
Programmer
Room
Thermostat
Boiler
Optional plug-in controls
On a Central Heating demand, the boiler will initially fire at minimum
output before modulating upwards to meet the actual system
requirement. Electronics within the boiler continually monitor the
heating flow temperature increasing or decreasing output on demand.
An anti-cycling device makes the Greenstar CDi range particularly
suitable for use on systems with TRV’s (Thermostatic Radiator Valves).
The flue can be run horizontally or vertically with additional 90 or
45 degree in-line bends allowing changes of route or direction,
providing an extremely flexible and versatile fluing system enabling
the appliance to be sited virtually anywhere.
Hot to
Basins and
Appliances
etc.
MT10RF mechanical RF thermostat
A simple, easy-to-operate 24 hour
mechanical timer combined with a
radio frequency room thermostat. The
thermostat features individual higher
and lower temperature sensors.
More details are shown on page 13.
A combi also supplies hot
water at mains pressure,
giving you exhilarating power
showering without the need for a pump. And as, on
average, a shower uses considerably less water than
a typical bath, the savings on hot water costs and
water consumption can be significant.
Hot to
Baths,
Showers
and Basins
COMBI SYSTEM
Versatility
Room
Thermostat
GREENSTAR CDi
Combi Boiler
Hot to Basins
and Appliances etc.
Gas
The Greenstar CDi series is manufactured in both natural gas and
LPG variants (40CDi LPG launch date to be confirmed).
DT20RF digital RF thermostat with twin
channel programmer
Controls
The CDi series design benefits
in operation
A condensing boiler is more efficient due to its ability to extract
more heat from the flue gases normally lost to the environment
through the flue system.
The CDi Series feature:
Power on/off switch.
Central heating variable temperature control selector.
An integral facia with status display lights and a digital display
which also operates as a fault diagnosis display.
A wall-mounted RF room thermostat
with digital display, combined with a
twin channel digital timer in the boiler
fascia. The fascia mounted
programmer benefits from automatic
time and date setup, automatic
summer/wintertime changeover
and a backlight for use in low light
conditions.
Hot water mode
All the Greenstar CDi models use the same Aluminium-Silicon heat
cell with an extra large surface area.
Whenever a hot water tap is turned on the incoming mains water will
activate a flow turbine which, via the electronic control system,
ignites the pre-mix burner. Boiler output is automatically boosted to
maximum to heat the incoming cold water as it passes through the
heat exchanger. Electronic controls modulate the boiler output
downwards to ensure the hot water temperature remains between
40 and 60ºC (as set by the consumer).
As the flue gases pass through the heat exchanger this extra
surface area cools the flue gases to around 55°C whereupon the
latent heat within, which would normally be lost to the atmosphere,
is instead released and applied to the system.
It is this ability to extract as much heat as possible from the gas it
burns that gives the Greenstar CDi series an exceptionally high level
of operating efficiency.
DT20 twin channel digital programmer
A versatile, easy-to-learn, 7 day,
digital programmer offering up to
3 on/off settings per day. The
programmer has a host of innovative
features including automatic setup,
which sets the correct time and date
at power-up, automatic summer/
wintertime changeover and a green
backlight for use in low light
conditions.
Keep hot facility
This higher efficiency is recognised within section L of the Building
Regulations, subsequently achieving a higher SAP or NHER rating.
All the Greenstar CDi combi models have an in-built keep hot facility
which will keep the primary water within the heat cell hot. This will
ensure that hot water is delivered instantly to the opened outlet.
Key features of the Greenstar CDi condensing boilers include the
separate plate domestic hot water heat exchanger, which is
guaranteed for 5 years.*
Eco mode
With the Eco mode button activated the keep hot facility is
de-energised and the hot water will be heated from cold. A slight
delay should be expected before the hot water is at full temperature
when in the Eco mode.
This, combined with the ‘keep hot’ facility, ensures that hot water is
delivered instantly to the tap.
*Subject to conditions
4
5
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 6
DT10RF digistat
Increased SAP ratings
A familiar wall-mounted 24 hour
programmable RF digital thermostat
combined with a fascia mounted single
channel programmer to time the hot
water cylinder or combi preheat
functions. The programmer includes a
built-in receiver for the room
thermostat and all of the functionality
of the DT20.
As well as the CDi models achieving very high SAP ratings for
dwellings, the addition of the optimising temperature controller further
increases these ratings as well as being part of the recommended
best practice, as covered by the CHESS design standard.
DT10RF optimiser
A seven day digital programmable RF
thermostat with a seven day
programmer/receiver in the boiler
fascia. The transmitter is the tried and
tested Optimiser as available with other
Worcester boilers. The optimum start
feature, where the thermostat delays
the firing of the boiler until necessary,
is a useful energy-saving option.
TD200 text display
A seven day programmer with easy-touse text display with automatic time
and date setup, automatic
summer/winter time changeover and a
backlight for use in low light conditions.
Three on/off periods can be set per
day. The TD200 can be fascia mounted
or hard wired outside the boiler using
the optional wall mounting socket. The TD200 features an easy-touse full text display providing more information than standard digital
controls. A hard wired room thermostat is available to provide
optimum start functionality.
RT10 room thermostat
Technical data – CDi series
Greenstar 25CDi
Greenstar 30CDi
Greenstar 35CDi
Greenstar 40CDi
(25kW) Combi Boiler
(30kW) Combi Boiler
(35kW) Combi Boiler
(40kW) Combi Boiler
Height (mm)
750 (max)
750 (max)
750 (max)
750 (max)
Width (mm)
440
440
440
440
Depth (mm)
360 (max)
360 (max)
360 (max)
360 (max)
Weight – dry (kg)
48.5
48.5
48.5
48.5
Heating Flow/Return Connections
22mm compression
22mm compression
22mm compression
22mm compression
Hot/Cold Water Connections
15mm compression
15mm compression
15mm compression
15mm compression
Pressure Relief Valve (mm Ø)
15
15
15
15
Condensate Connection
22mm Plastic Pipe
22mm Plastic Pipe
22mm Plastic Pipe
22mm Plastic Pipe
Gas Connection
22mm compression
22mm compression
22mm compression
22mm compression
Primary Water Content (litres)
3.75
3.75
3.75
3.75
Minimum Domestic Inlet Pressure
For Maximum DHW Flow Rate (bar)
1.2
1.4
1.5
1.7
Minimum Domestic Inlet Pressure
To Operate The Appliance (bar)
0.2
0.2
0.2
0.2
Maximum Domestic Inlet Pressure (bar)
10
10
10
10
DHW Flow Rate @ 35°CΔT (l/min)
10.5
12.6
14.3
16.3
DHW Flow Rate @ 40°CΔT (l/min)
9.2
11.1
12.5
14.3
7.7 - 25
(26,272 - 85,300)
7.7 - 30
(26,272 - 102,360)
7.7 - 30
(26,272 - 102,360)
7.7 - 30
(26,272 - 102,360)
Wall Mounting Jig
Yes
Yes
Yes
Yes
Filling Loop
Yes
Yes
Yes
Yes
Plug-In Timers
Yes (Optional)
Yes (Optional)
Yes (Optional)
Yes (Optional)
Yes (Optional)
Yes (Optional)
Yes (Optional)
Yes (Optional)
Intelligent Controls
Yes (Optional)
Yes (Optional)
Yes (Optional)
Yes (Optional)
Condensing In DHW Mode
Yes
Yes
Yes
Yes
Maximum Vertical Flue (mm)
(100mmØ) inc. terminal
11,500
9,400
8,000
4,900
Maximum Horizontal Flue (mm) (100mmØ)
10,000
7,900
6,500
2,600
Maximum Horizontal Flue (mm) (125mmØ)
23,000
18,500
16,000
12,500
Maximum Vertical Flue (mm)
(125mmØ) inc. terminal
23,000
18,500
16,000
16,000
SEDBUK Value %/Band
90.3%/Band A
90.3%/Band A
90.3%/Band A
90.2%/Band A
NOX Classification
Class 5
Class 5
Class 5
Class 5
Model
Output To Central Heating
A hard wired optimising room
temperature controller with digital
display for use with the TD200. The
display shows current and desired
temperature and an advance button
allows the user to move to the next
heating switch point on the TD200.
kW
(Btu)
Optimising Room Temperature Controller
TD200 wall mounting socket
A Worcester branded wall mounting
socket which allows the TD200 to be
hard wired away from the boiler.
6
7
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 8
The Greenstar CDi condensing
combi boiler – inside story
Installing the
Greenstar CDi series
All combi boilers require less installation time than a conventional
boiler, for these reasons:
Compartment installation
1. All the major components, including the pump, are contained
within the boiler casing and do not need to be fitted separately.
2. The boiler comes pre-wired and pre-plumbed.
3. There is no need to install a hot water cylinder.
4. There is no need to install a storage tank in the roof space.
5. There is less pipe work.
5
The appliance may be installed in any room, although particular
attention is drawn to the requirements of the IEE regulations
applicable and in Scotland the electrical provisions with respect to
installation in a room containing a bath or shower.
Wall preparation
However, the Greenstar CDi series is exceptional for its number of
additional time-saving installation features:
1
9
2
The picture shows the CDi wall mounting jig which enables a
simple and straightforward method of attaching the boiler to the
wall surface.
Automatic gas pressure adjustment
Unique and highly versatile multi-directional fluing system
Combined ignition and control board means less connections
Plug in filling loop as standard
Optional plug in timers
No bypass required
Optional Intelligent Combi Package
After fixing the jig to the wall, the appliance can be lifted onto the
jig and the union connections tightened. The pipe work can be
routed behind the boiler without the need for an additional wall
spacing frame.
6
Siting of appliance
General
7
The appliances are not suitable for external installation.
4
The wall on which the boiler is to be mounted should be capable
of supporting an overall weight of approximately 50 kg.
3
8
11
10
12
13
14
16
15
The wall does not require special protection. However, if the
appliance is to be fitted in a timber frame building the guidelines
laid down in BS 5440:Part 1:2000 and the gas installer manual
Chapter 11, “Gas in Timber Frame Housing” should be adhered to.
The appliances may be installed into an airing cupboard if required.
Use a non-combustible perforated material (max. hole sizes of
13mm) to separate the boiler from the airing space.
Condensate disposal
All condensing boilers generate condensate discharge which
needs to be piped away from the appliance in via a plastic pipe.
Clearances
The minimum clearances shown below should be allowed for
installation, servicing and ventilation-free compartment installations.
960mm
The amount of condensate generated depends on the efficiency
and operating status of the appliance. The boilers will generally
only produce condensate whilst operating in central heating mode.
Some models will condense in both heating and hot water modes
and can generate up to 2 litres of condensate water an hour.
450mm
Key to components
1.
Aluminium/Silicon WB5 Heat Exchanger
9.
2.
Pre-mix Fan
10. Syphon
3.
Circulating Pump
11. Diverter Valve
4.
Pressure Gauge
12. Drain Point
5.
Down Firing Low Nox Burner
13. On/Off Button
6.
Plate DHW Heat Exchanger
14. Central Heating Temperature Control
7.
Automatic Air Vent
15. Domestic Hot Water Temperature Control
8.
Gas Valve
16. Digital Display
8
Expansion Vessel
Using 100mm flue kit
- 1,112mm
Using 125mm flue kit
- 1,152mm
9
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 10
Condensate termination and route
External condensate pipe work
The condensate connection on the Worcester appliances is in 22mm
plastic. The pipe should be extended and run away from the appliance
with a constant fall of 2.5 degrees or 50mm in every metre.
Flue terminal positioning
All Worcester condensing boilers have within a syphonic condensate
trap. Rather than the condensate constantly dripping into the
discharge pipe, the condensate is collected into a trap which
releases it in 100ml quantities. This will help prevent freezing
occurring.
The condensate pipe can terminate into any one of five areas:
Key to illustration
RSF horizontal and vertical
Minimum dimensions of flue terminal positions for
balanced room sealed flues with fanned draught:
Terminal Position
Directly below an opening, air brick, opening windows etc.
Above an opening, air brick, opening window etc.
Horizontally to an opening, air brick, opening window etc.
Below gutters, soil pipes or drain pipes
Below eaves
Below balconies or car port roof (lowest point)
From a vertical drain pipe or soil pipe
From an internal or external corner or to a boundary
alongside the terminal
I Above ground, roof or balcony
J From a surface or boundary facing the terminal
K From a terminal facing the terminal
L2 From an opening in the car port
(e.g. door, window) into the dwelling
M Vertically from a terminal on the same wall
N Horizontally from a terminal on the same wall
O From a non-combustible vertical structure on the roof
P Above intersection with the roof
Q Adjacent to windows or openings on pitched and flat roofs
R Below windows or openings on pitched roofs
Wherever possible the condensate discharge pipe work should be
routed and terminated internally. Should this not be possible, and the
only available route is external, the following conditions should be
observed:
Internal sink/washing
machine drain
Internal waste drainage system
The pipe work length should be kept to a minimum and the route
as vertical as possible
Where pipe work could be subjected to extreme cold or wind chill,
a weather proof insulation should be used. Alternatively, the
condensate pipe work could be increased to a minimum
32mm without the requirement to insulate
Q
Q
R
Pipe work connections and casing
dimensions
C
Cabinet dimensions
A
B
C
Soil and vent stack
External drainage system
750mm*
440mm
360mm
*760mm to top of casing front.
A
B
External condensate absorption point (unsuitable for clay soil types)
Min Distance
A1
B1
C1
D
E
F2
G
H
The flue system must be installed and terminated in accordance with
the recommendations of BS 5440:Part 1.
300mm
300mm
300mm
75mm
200mm
200mm
150mm
300mm**
300mm
600mm**
1,200mm
1,200mm
1,500mm
300mm
*
*
600mm
2,000mm
1
In addition, the terminal should not be nearer than 150 mm (fanned draught) to an opening in the
building fabric formed for the purpose of accommodating a built-in element such as a window frame.
2
Not recommended.
* See instructions supplied with vertical flue kits.
** Care should be taken to ensure terminal siting does not cause a nuisance to adjacent properties.
General position
1. The terminal must not cause an obstruction nor the discharge a
nuisance. Particular care should be exercised with regards to the
pluming of the flue gases and any increase in noise levels.
3. In certain weather conditions, a white plume of condensation will
be emitted from the flue terminal and siting where this could be
a nuisance, i.e. near security lighting, should be avoided.
2. If a terminal is fitted less than 2 metres above a surface to which
people have access, then a guard must be fitted. A terminal
protective guard is available from Tower Flue Components, Vale
Rise, Tonbridge. Tel No. (01732) 351555. The terminal guard must
be securely fixed to the wall using suitable plugs and corrosion
resistance screws. The guard must be symmetrically positioned
about the terminal assembly and spaced such that there is a gap
of 50mm between the end of the terminal and the guard.
4. The air inlet/outlet duct and the terminal of the boiler must not
be closer than 25mm to any combustible material. Detailed
recommendations on protection of combustible materials are
given in BS 5440:1.
Pipe work connections
A - Condensate from boiler syphon/trap
G - 300mm x 100mmØ sealed plastic tube
B - Sink with integral overflow
H - Ground level
A
CH Flow
22mm
C - 21.5mmØ plastic condensate pipe
D - External drain or gully
J - Drainage holes 50mm facing away from
building
B
CH Return
22mm
E - Internal soil and vent stack
K - Limestone chippings
C
Gas Inlet
22mm
Bathrooms
F - Serviceable condensate trap (75mm min.)
L - Weather resistant insulation
D
Mains Water Inlet
15mm
E
DHW Outlet
15mm
The boiler can be installed in zones 2 or 3. If a mechanical or RF
mechanical timer or text display with room thermostat (IP 20 only) is
fitted the boiler can only be installed in zone 3.
A
Whilst all of the above methods are acceptable it is always the best
practice to terminate the condensate pipe via an internal waste
system. This will eliminate the need for any external condensate
pipe runs which can be susceptible to freezing in extreme weather.
Best practise is not to run external condensate pipe any further than
3m. If it is necessary to run more than 3m externally increase pipe
size to 35mm.
Boiler location & clearances
600mm
600mm
750mm
E
A non mechanical timer can be installed in zone 2.
C
3
D
B
See IEE wiring regulations. (See Technical Data for IP ratings).
2
1
1
2
3
2250mm
IMPORTANT: any switch or appliance control using mains
electricity must not be able to be touched by a person using the bath
or shower.
Electrical switches, fused spur and socket outlets must not be
situated in the bathroom.
600mm
All pipe work to the appliance must be cross bonded.
750mm
1
1
2
600mm radius
10
11
3
2250mm
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 12
Greenstar CDi combi boiler series
horizontal fluing options
The Greenstar CDi series has the choice of 2 differently sized
horizontal RSF flue systems, 100mm and 125mm. Both systems
have different maximum lengths. Options 1 to 6
detail the permissible lengths.
Option 2
EXTENSION FLUE HORIZONTAL
Option 1
STANDARD HORIZONTAL FLUE ASSEMBLY
Horizontal RSF Flue
Maximum total straight flue length
100mm
Flue Diameter
100mm
Minimum Flue Length
Maximum Flue Length - 25CDi
30CDi
35CDi
40CDi
125mm
342mm
10,000mm
7,900mm
6,500mm
2,600mm
250mm
23,000mm
18,500mm
16,000mm
12,500mm
1,030mm (125mm dia) of flue duct
including terminal (as measured
from centre of flue outlet)
}
Part No. 7 719 002 345 (100mm dia)
Part No. 7 719 002 497 (100mm dia)
Part No. 7 719 002 350 (125mm dia)
686mm 1,070mm
35CDi
686mm 1,070mm
40CDi
686mm 1,070mm
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Standard Flue Kit
1
7 719 002 497
125mm
Standard Flue Kit
1
7 719 002 350
30CDi
Worcester Part No.
100mm
125mm
90º Elbow
45º Elbow
Vertical Adaptor
30CDi
Maximum total straight flue length
100mm
25CDi
7 719 002 349
(960mm long)
7 719 002 348
7 719 002 347
7 719 002 432
The following criteria should be noted when planning the installation.
– The flue system inclines 21⁄2" (44mm per metre) from the appliance, to
prevent condensation from dripping from the flue terminal.*
– Because the appliance operates at high efficiency a white plume
of condensation will be emitted from the terminal. Care must be
taken when selecting the flue terminal position.
18,500mm
35CDi
6,500mm
16,000mm
40CDi
2,600mm
12,500mm
Flue Components Required
25CDi
Description
Quantity
Worcester Part No.
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 10
7 719 002 349
Description
Quantity
Worcester Part No.
125mm
Standard Flue Kit
1
7 719 002 350
100mm
Standard Flue Kit
1
7 719 002 497
125mm
Extension Flue Kit
up to 23
7 719 001 892
125mm
Standard Flue Kit
1
7 719 002 350
Description
Quantity
Worcester Part No.
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 8
7 719 002 349
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 18
7 719 001 892
30CDi
Flue Diameter
40CDi
Accessories
7,900mm
Flue Diameter
35CDi
7 719 001 892
(1,000mm long)
7 719 001 891
7 719 001 899
7 719 002 433
125mm
10,000mm 23,000mm
30CDi
Flue Diameter
600mm (100mm dia) of flue duct
Extension Flue Kit
686mm 1,070mm
Flue Components Required
25CDi
Standard flue kit
Comprises:
1 x Flue Turret Elbow
125mm
25CDi
35CDi
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Standard Flue Kit
1
7 719 002 497
Flue Diameter
Description
Quantity
Worcester Part No.
125mm
Standard Flue Kit
1
7 719 002 350
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 6
7 719 002 349
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 15
7 719 001 892
Description
Quantity
Worcester Part No.
40CDi
Flue Diameter
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 2
7 719 002 349
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 12
7 719 001 892
*The 100mm flue system exhaust pipe inclines 2 degrees within the 100mm air duct.
12
13
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 14
Option 3
EXTENSION FLUE HORIZONTAL AND UPWARDS
Option 4
Option 5
Option 6
EXTENSION FLUE HORIZONTAL USING A SECOND
90˚ BEND
EXTENSION FLUE UPWARDS AND HORIZONTAL USING
A SECOND 90˚ BEND
EXTENSION FLUE UPWARDS AND HORIZONTAL USING
A THIRD 90˚ BEND
x2
x3
Maximum total straight flue length
Maximum total straight flue length
100mm
25CDi
125mm
10,000mm 23,000mm
30CDi
7,900mm
18,500mm
35CDi
6,500mm
16,000mm
40CDi
2,600mm
12,500mm
5,900mm
16,500mm
35CDi
4,500mm
14,000mm
40CDi
600mm
10,500mm
30CDi
5,900mm
16,500mm
35CDi
4,500mm
14,000mm
40CDi
N/A
10,500mm
1
7 719 002 497
7 719 002 497
100mm
Extension Flue Kit
up to 9
7 719 002 349
Flue Diameter
Description
Quantity
Worcester Part No.
7 719 002 349
100mm
90˚ Elbow
1
7 719 002 438
100mm
Standard Flue Kit
1
7 719 002 497
1
100mm
Extension Flue Kit
up to 11
7 719 002 348
7 719 002 432
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 23
7 719 001 892
125mm
90º Elbow
1
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 21
7 719 001 892
125mm
90˚ Elbow
1
7 719 001 891
30CDi
30CDi
100mm
Extension Flue Kit
up to 7
7 719 002 349
100mm
90˚ Elbow
1
7 719 002 438
Extension Flue Kit
up to 17
7 719 001 892
125mm
90º Elbow
1
7 719 001 891
Vertical Adaptor
1
125mm
up to 22
7 719 001 892
90˚ Elbow
1
30CDi
Quantity
Worcester Part No.
7 719 002 350
100mm
Standard Flue Kit
1
7 719 002 497
7 719 001 892
100mm
Extension Flue Kit
up to 8
7 719 002 349
7 719 001 891
100mm
90º Elbow
2
7 719 002 348
100mm
Vertical Adaptor
1
7 719 002 432
Quantity
Worcester Part No.
125mm
Standard Flue Kit
1
7 719 002 350
100mm
Standard Flue Kit
1
7 719 002 497
125mm
Extension Flue Kit
up to 18
7 719 001 892
100mm
Extension Flue Kit
up to 5
7 719 002 349
125mm
90º Elbow
2
7 719 001 891
7 719 002 438
125mm
Vertical Adaptor
1
7 719 002 433
1
35CDi
Flue Diameter
Description
Quantity
Worcester Part No.
125mm
Standard Flue Kit
1
7 719 002 350
100mm
Standard Flue Kit
1
7 719 002 497
125mm
Extension Flue Kit
up to 14
7 719 001 892
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Extension Flue Kit
up to 7
7 719 002 349
125mm
90˚ Elbow
1
7 719 001 891
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 6
7 719 002 349
100mm
90º Elbow
1
7 719 002 348
100mm
Vertical Adaptor
1
7 719 002 432
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 16
7 719 001 892
125mm
90º Elbow
1
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
40CDi
40CDi
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Standard Flue Kit
1
7 719 002 497
90º Elbow
2
7 719 002 348
100mm
Vertical Adaptor
1
7 719 002 432
Extension Flue Kit
1
7 719 002 349
100mm
90˚ Elbow
1
7 719 002 438
125mm
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 11
7 719 001 892
125mm
90˚ Elbow
1
7 719 001 891
3,900mm
14,500mm
35CDi
2,500mm
12,000mm
40CDi
N/A
8,500mm
Description
Quantity
Worcester Part No.
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 9
7 719 002 349
100mm
90º Elbow
3
7 719 002 348
100mm
Vertical Adaptor
1
7 719 002 432
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 21
7 719 001 892
125mm
90º Elbow
3
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
Description
Quantity
Worcester Part No.
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 7
7 719 002 349
100mm
90º Elbow
3
7 719 002 348
100mm
Vertical Adaptor
1
7 719 002 432
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 17
7 719 001 892
125mm
90º Elbow
3
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
Description
Quantity
Worcester Part No.
35CDi
100mm
100mm
30CDi
100mm
Flue Diameter
125mm
19,000mm
Flue Diameter
Flue Diameter
Description
90˚ Elbow
125mm
6,000mm
30CDi
Description
Flue Diameter
100mm
35CDi
Extension Flue Kit
Flue Diameter
35CDi
7 719 002 433
125mm
7 719 002 433
125mm
up to 19
7 719 002 350
7 719 001 891
1
Extension Flue Kit
1
2
Standard Flue Kit
125mm
Standard Flue Kit
1
125mm
7 719 002 350
125mm
90º Elbow
7 719 002 349
1
7 719 002 432
Vertical Adaptor
up to 9
Standard Flue Kit
1
125mm
Extension Flue Kit
125mm
Vertical Adaptor
125mm
100mm
7 719 002 432
7 719 002 348
7 719 002 497
7 719 002 497
7 719 002 348
2
1
1
1
90º Elbow
Standard Flue Kit
Standard Flue Kit
1
100mm
100mm
100mm
90º Elbow
7 719 002 349
Worcester Part No.
Worcester Part No.
Vertical Adaptor
up to 10
Quantity
Quantity
100mm
Extension Flue Kit
Description
Description
100mm
100mm
100mm
100mm
25CDi
Flue Components Required
25CDi
Flue Diameter
Flue Diameter
Maximum total straight flue length
Flue Components Required
25CDi
Standard Flue Kit
Standard Flue Kit
1
125mm
21,000mm
100mm
100mm
1
100mm
8,000mm
25CDi
Worcester Part No.
Worcester Part No.
125mm
Maximum total straight flue length
Quantity
Quantity
Vertical Adaptor
30CDi
Description
Description
100mm
21,000mm
Flue Diameter
Flue Diameter
90º Elbow
125mm
8,000mm
Flue Components Required
25CDi
Flue Components Required
25CDi
100mm
100mm
25CDi
Standard Flue Kit
1
7 719 002 350
Extension Flue Kit
up to 15
7 719 001 892
125mm
90º Elbow
2
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
100mm
Standard Flue Kit
1
7 719 002 497
100mm
Extension Flue Kit
up to 5
7 719 002 349
100mm
90º Elbow
3
7 719 002 348
100mm
Vertical Adaptor
1
7 719 002 432
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 14
7 719 001 892
125mm
90º Elbow
3
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
Flue Diameter
Description
Quantity
Worcester Part No.
125mm
Standard Flue Kit
1
7 719 002 350
40CDi
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Standard Flue Kit
1
7 719 002 497
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Extension Flue Kit
up to 3
7 719 002 349
125mm
Standard Flue Kit
1
7 719 002 350
40CDi
100mm
90º Elbow
1
7 719 002 348
125mm
Extension Flue Kit
up to 12
7 719 001 892
100mm
Vertical Adaptor
1
7 719 002 432
125mm
90º Elbow
2
7 719 001 891
125mm
Extension Flue Kit
up to11
7 719 001 892
7 719 002 433
125mm
90˚ Elbow
3
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
125mm
Standard Flue Kit
1
7 719 002 350
125mm
Extension Flue Kit
up to 13
7 719 001 892
125mm
90º Elbow
1
7 719 001 891
125mm
Vertical Adaptor
1
7 719 002 433
125mm
14
Vertical Adaptor
1
15
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 16
Greenstar CDi combi boiler series
vertical fluing options
The Greenstar CDi series have the choice of 2 differently sized
vertical RSF flue systems, 100mm and 125mm. Both systems
have different maximum lengths. Options 1 to 3 detail the
permissible lengths.
Pitc
h
roo ed
f
Pitc
h
roo ed
f
Vertical RSF Flue
100mm
125mm
Flue Terminal
Assembly Diameter
135mm
135mm
Maximum Flue Length - 25CDi
(inc terminal)
30CDi
35CDi
40CDi
11,500mm
9,400mm
8,000mm
4,900mm
23,000mm
18,500mm
16,000mm
16,000mm
Flue Terminal
Assembly Length
1,140mm
1,365mm
500mm
Flat roof
300mm
L = 100mmØ 1,140mm
L = 125mmØ 1,365mm
Flat roof
300mm
L = 100mmØ 1,140mm
L = 125mmØ 1,365mm
Maximum total straight flue length
Straight flue
Length
Flue Components Required
25CDi
Maximum total straight flue length
100mm
Vertical balanced flue kit
Comprises:
1 x Flue Terminal Assembly
1 x Weather Sealing Collar
1 x Fire Stop Spacer
1 x Vertical Adaptor
}
Part No. 7 719 002 430 (100mm dia)
Part No. 7 719 002 431 (125mm dia)
125mm
25CDi
11,500mm 23,000mm
30CDi
9,400mm
18,500mm
35CDi
8,000mm
16,000mm
40CDi
4,900mm
16,000mm
Flue Components Required
25CDi
Flue Diameter
Accessories
Description
Quantity
Worcester Part No.
100mm
125mm
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Vertical Flue Kit
1
7 719 002 430
125mm
Vertical Flue Kit
1
7 719 002 431
Description
Quantity
Worcester Part No.
100mm
Vertical Flue Kit
1
7 719 002 430
125mm
1
7 719 002 431
35CDi
30CDi
7,400mm
16,500mm
35CDi
6,000mm
14,000mm
40CDi
2,900mm
14,000mm
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Extension Flue Kit
up to 10
7 719 002 349
100mm
45˚ Elbow
2
7 719 002 347
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 21
7 719 001 892
125mm
45˚ Elbow
2
7 719 001 899
Description
Quantity
Worcester Part No.
Vertical Flue Kit
1
7 719 002 430
Extension Flue Kit
up to 11
7 719 002 349
Flue Diameter
Description
Quantity
Worcester Part No.
Flue Diameter
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Vertical Flue Kit
1
7 719 002 430
7 719 002 431
100mm
Extension Flue Kit
up to 8
7 719 002 349
100mm
45˚ Elbow
2
7 719 002 347
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 23
7 719 001 892
7 719 001 892
(1,000mm long)
90º Elbow
7 719 002 348
7 719 001 891
Flue Diameter
Description
Quantity
Worcester Part No.
45º Elbow
7 719 002 347
7 719 001 899
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Extension Flue Kit
up to 9
7 719 002 349
30CDi
125mm
30CDi
Vertical Flue Kit
1
40CDi
Flue Diameter
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 18
7 719 001 892
Description
Quantity
Worcester Part No.
100mm
Vertical Flue Kit
1
7 719 002 430
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 17
7 719 001 892
125mm
45˚ Elbow
2
7 719 001 899
Description
Quantity
Worcester Part No.
35CDi
Flue Diameter
35CDi
100mm
Vertical Flue Kit
1
7 719 002 430
Extension Flue Kit
up to 6
7 719 002 349
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
45˚ Elbow
2
7 719 002 347
100mm
Extension Flue Kit
up to 8
7 719 002 349
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 14
7 719 001 892
125mm
Extension Flue Kit
up to 16
7 719 001 892
125mm
45˚ Elbow
2
7 719 001 899
Description
Quantity
Worcester Part No.
40CDi
40CDi
Flue Diameter
16
21,000mm
100mm
7 719 002 349
(960mm long)
Note: The roof flashing is not supplied by Worcester.
Vertical Flue Kit
125mm
9,500mm
Flue Components Required
25CDi
30CDi
Flue Diameter
100mm
25CDi
100mm
Worcester Part No.
Extension Flue Kit
VERTICAL BALANCED FLUE SYSTEM WITH TWO 45° BENDS
VERTICAL BALANCED FLUE SYSTEM MAXIMUM HEIGHT
500mm
Flue Diameter
Option 2
MINIMUM HEIGHT
Option 1
Description
Quantity
Worcester Part No.
Flue Diameter
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Extension Flue Kit
up to 5
7 719 002 349
100mm
Extension Flue Kit
up to 3
7 719 002 349
125mm
Vertical Flue Kit
1
7 719 002 431
100mm
45˚ Elbow
2
7 719 002 347
125mm
Extension Flue Kit
up to 16
7 719 001 892
17
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 14
7 719 001 892
125mm
45˚ Elbow
2
7 719 001 899
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 18
Installation requirements
Plastic pipe work
Installation of the Greenstar CDi Series must be in accordance with
the relevant requirements of the Gas Safety (Installation Use)
Regulations (as amended), current IEE Wiring Regulations, local
Building Regulations, Building Standards (Scotland) (Consolidation)
regulations and bylaws of the local Water company and Health and
Safety Document No. 635 (Electricity at Work Regulations 1989).
It should be in accordance with the relevant recommendations of
the following British Standards:
Option 3
VERTICAL BALANCED FLUE SYSTEM WITH TWO
90° BENDS
The use of plastic pipe work is acceptable. However, some plastics
are permeable to oxygen and must be avoided. Only pipe work with
a polymeric barrier should be used. Please note that the first
600mm of pipe work connected to the boiler must be of copper
or steel.
Natural gas supply
BS 6798; BS 5449; BS 5546:1; BS 5440:1; BS 5440:2;
BS 6891.
Maximum total straight flue length
100mm
125mm
25CDi
7,500mm
19,000mm
30CDi
5,400mm
14,500mm
35CDi
4,000mm
12,000mm
40CDi
N/A
12,000mm
The appliances when on a hot water or full output demand will
require up to 2.6m3/hr of gas (25kW). The gas meter and supply
pipes must be capable of supplying this quantity of gas in addition
to the demand from any other appliance being served. It is
important that a gas supply pipe of at least 22mm diameter is
used. Under no circumstances should the size of the gas supply
pipe be less than that of the appliance inlet connection. The meter
outlet governor should be capable of ensuring a dynamic pressure
of 20mbar (8in wg) at the appliance. Particular consideration should
be given to the resistance to gas flow created by elbows, bends
etc. Pipe work should be sized to overcome this resistance and
details of this are given in the table below.
Gas Safety (Installation and Use) Regulations. All gas appliances
must be installed by a Corgi registered person in accordance with
the above regulations. Failure to install appliances correctly could
lead to prosecution.
The manufacturers notes must not be taken in any way as
overriding statutory regulations.
Sealed primary systems
Flue Components Required
25CDi
Description
Quantity
Worcester Part No.
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Extension Flue Kit
up to 9
7 719 002 349
100mm
90˚ Elbow
2
7 719 002 348
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 20
7 719 001 892
125mm
90˚ Elbow
2
7 719 001 899
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Extension Flue Kit
up to 7
7 719 002 349
100mm
90˚ Elbow
2
7 719 002 348
Worcester Greenstar CDi combi boilers are supplied complete with
all the necessary components to form a sealed primary system.
Included are a pre-plumbed expansion vessel, a pressure relief valve
(set at 3bar), an automatic air vent and a pressure gauge.
Total length of Gas Supply Pipe (metres)
With an initial system pressure of 0.5bar a system capacity
of approximately 83 litres can be accommodated. Refer to
BS 7074:Part 1 for more information. The charge pressure can
be increased by with a decrease in system volume.
Gas Discharge
Rate m3/h
Flue Diameter
It is important with an Aluminium Heat Exchanger that the pH level
of the water does not exceed 8. Levels in excess of this could be
detrimental to the Heat Exchanger.
30CDi
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 16
7 719 001 892
125mm
90˚ Elbow
2
7 719 001 899
Flue Diameter
Description
Quantity
Worcester Part No.
100mm
Vertical Flue Kit
1
7 719 002 430
100mm
Extension Flue Kit
up to 5
7 719 002 349
100mm
90˚ Elbow
2
7 719 002 348
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 13
7 719 001 892
125mm
90˚ Elbow
2
7 719 001 899
Flue Diameter
Description
Quantity
Worcester Part No.
125mm
Vertical Flue Kit
1
7 719 002 431
125mm
Extension Flue Kit
up to 13
7 719 001 892
125mm
90˚ Elbow
2
7 719 001 899
Valves and joints
It is very important that all valves and joints are able to sustain a
working pressure of up to 3bar (45psi). Particular care should be
exercised when fitting radiator valves and only those of high quality
to BS 2767:10 should be used. All other valves and fittings should
comply with BS 1010.
40CDi
Loss of water pressure from a sealed system will require continuous
recharging with fresh water and consequential introduction of air. Air
is highly corrosive and will considerably reduce life expectancy of
radiators, pumps etc.
18
9
2.9
–
–
15
8.7
5.8
4.6
22
18.0
12.0
9.4
28
Elbows or Tees
The supplied plug in filling loop simply
connects between the cold main
connection and the heating return
circuit on the wall mounting jig.
35CDi
6
Approximate Additional Length to be Allowed (Natural gas)
The use of a suitable inhibitor will provide a resistance to this.
Contact Betz Dearborn (Tel: 0151 4209595) or
Fernox (Tel: 01799 521133) for further details.
System filling and make-up
125mm
3
Pipe
Diameter
(mm)
19
90º Bends
Metres
Feet
Metres
Feet
0.5
2
0.3
1
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 20
Installation requirements continued
Cold water connection
Propane gas supply
Connection should be made as shown in the pipe work detail and
the appliance installed generally in accordance with the layout
shown on page 10.
The Greenstar CDi Series is available in a propane gas version. The
appliance when on a hot water or full output demand will require up to
2.0 kg/h of gas (25kW). The gas tank or bottles must be capable of
supplying this quantity of gas at a nominal pressure of 37mbar
(14.8in wg) at the appliance. The table below shows the propane gas
discharge through varying lengths of pipe and the resistance to flow
created by elbows, bends etc. Pipe work should be sized to overcome
this resistance.
Gas Discharge
Rate m3/h
Total length of Gas Supply Pipe (metres)
3
6
9
Pipe
Diameter
(mm)
1.5
1.01
–
15
8.0
5.2
4.2
22
15.9
8.9
8.3
28
Wherever possible the cold supply to the appliance should be the
first connection off the mains supply, in order to minimise hot water
flow reduction when cold water services are operated. The final
600mm of piping to the appliance should be of copper only.
Elbows or Tees
To achieve the stipulated flow rate a working cold water mains
pressure of between 1.2 and 1.7bar is required (dependent on
model). The appliance will operate at a minimum working pressure
of only 0.2bar (3psi) however a reduced hot water flow rate should
be expected. Where back-flow prevention devices, including water
meters, are fitted the expansion of hot water into the cold water
main can be prevented. This can result in a pressure build-up that
may cause damage to the boiler and household devices such as
showers, washing machines etc. In these cases we recommend that
a mini-expansion vessel (Part No. 7 716 192 105) be fitted
adjacent to the boiler in the cold water main.
MAINS WATER EXPANSION VESSEL:
A - Mini expansion vessel, Part No. 7 716 192 105
B - Mains water inlet pipe
C - Non-return valve
D - Boiler
90º Bends
Metres
Feet
Metres
Feet
0.6
2
0.3
1
Taps and valves
Hot and cold taps and mixing valves used with the Greenstar CDi
Series appliance must be suitable for operating at a mains pressure
and temperatures of 65°C (150°F).
Showers
Cold water pressure
Approximate Additional Length to be Allowed (LPG)
Hot water systems
When a loose head shower with a flexible hose is used over a bath
or shower tray, the hose must be fixed so that the head cannot fall
closer than 25mm (1in) above the top edge of the spill over level
of the relevant bath or shower tray. Alternatively, the feed pipes to
the shower should incorporate a double check valve assembly or a
check valve and vacuum breaker.
With fixed head showers no provision is necessary.
The use of a thermostatically controlled shower will give added
comfort and safeguard against high hot water temperatures.
Alternatively, a pressure balancing shower valve specifically
designed for constant temperature water heaters would be suitable.
Bidet
The supply of hot and cold water mains direct to a bidet is
permitted provided that the bidet is of the overrim water feed type.
The outlet(s) should be shrouded and not to have any temporary
hand held spray attached. No other anti-syphonage arrangements
are necessary.
D
Electricity supply
A
B
A 3amp fused three pin plug and unswitched shuttered socket
outlet (both complying with BS 1362) or preferably a double pole
isolator with a contact separation of 3mm in all poles supplying the
appliance should be used.
Use in hard water areas
C
As the maximum temperature of the domestic hot water heat
exchanger is limited by the electronic control circuit, there is
normally no need for water treatment to prevent scale accumulation.
The appliance electrical circuits are also protected by an internal
2amp fuse. The appliance must be earthed.
Hot water supply
A domestic hot water flow regulator, set to give an optimum flow
rate of between 10.2 and 16.3lts/min ±15% (dependent on model)
is fitted to the cold supply of the hot water heat exchanger.
Mains cold water supply
Water Authority requirement
A direct mains cold water connection is permitted by Water
Authorities. However, it is recommended that reference be made to
local requirements. In the event of difficulty contact Worcester
Technical Department.
As with all mains fed systems, the flow rate of water obtainable from
individual taps will vary in relation to the number of taps operating
simultaneously, and will depend upon the cold mains supply
available to the property.
Pipe sizing
Therefore, in order to avoid excessive starvation of flow to individual
taps, flow balancing may be required by the use of proprietary
constant volume flow regulators or Ball-o-Fix valves.
Unless the mains pressure is low, a standard 15mm diameter
service pipe is normally suitable. A 15mm hot water distribution pipe
to the first branch is recommended thereafter 15mm and/or 10mm
to all draw off points.
20
In areas where exceptional water conditions prevail, consideration
may need to be given to the fitting of a device capable of preventing
scale. In such circumstances the advice of the local water authority
should be sought.
Warranty
Worcester Greenstar CDi appliances are offered with a full
2 year guarantee* on parts and labour. Ongoing service may be
arranged through the Worcester Customer Service Department.
*Subject to conditions.
21
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 22
Notes
Notes
22
23
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 24
The Greenstar CDi series
accessories
MT10 MECHANICAL TIMER
MT10RF MECHANICAL
RF THERMOSTAT
DT20 TWIN CHANNEL
DIGITAL PROGRAMMER
DT20RF DIGITAL RF
THERMOSTAT WITH TWIN
CHANNEL PROGRAMMER
A Complete
After-sales Service
As part of the worldwide Bosch Group, Worcester strives to maintain
the highest possible standards of after-sales care.
In addition to the no-nonsense parts and labour warranty applicable
to all Worcester boilers, you and your customers have the assurance
that every Worcester boiler is manufactured to both the appropriate
British and European standards.
Worcester Contact Centre
Worcester Part No. 7 716 192 036
Worcester Part No. 7 716 192 037
Worcester Part No. 7 716 192 038
Worcester Part No. 7 716 192 041
DT10RF DIGISTAT
DT10RF OPTIMISER
RT10 ROOM THERMOSTAT
TD200 TEXT DISPLAY
Should you require support, our fully trained Contact Centre staff,
based at our head office in Worcester, are ready to take your calls.
Whatever your query our contact centre operators along with our
nationwide team of engineers are ready to help you.
Boiler Protection Options
Worcester Part No. 7 716 192 039
Worcester Part No. 7 716 192 040
Worcester Part No. 7 719 002 505
Worcester Part No. 7 719 002 506
TEXT DISPLAY WALL
MOUNTING SOCKET
45º BEND
(100MM DIA)
45º BEND
(125MM DIA)
90º BEND
(100MM DIA)
To protect and maintain your boiler it is recommended that you
invest in a comprehensive maintenance contract. For more
information please discuss with your CORGI/OFTEC registered
installer or alternatively contact Worcester Service Contracts Team
on 01905 754 624.
Contact Centre
Tel: 08457 256 206
Fax: 01905 754 701
Opening Times
Monday – Friday: 7.00am – 8.00pm
Saturday: 8.00am – 5.00pm
Sunday: 9.00am – 12 noon
All the Technical Advice You Need
Spares
Worcester Part No. 7 719 002 718
Worcester Part No. 7 719 002 347
Worcester Part No. 7 719 001 899
Worcester Part No. 7 719 002 348
90º BEND
(125MM DIA)
1M EXTENSION
(100MM DIA)
1M EXTENSION
(125MM DIA)
VERTICAL BF KIT
(100MM DIA)
Genuine replacement parts for all Worcester boilers are readily
available from stock, on a next day delivery basis. For more
information please call your local stockist.
Customer Technical Support
The Worcester Technical Helpline is a dedicated phone line –
committed to providing a comprehensive service to complement the
brand name and quality of our boiler products. Our experienced team
of technical experts provide the answers to queries of a technical
nature across the entire Worcester range.
Worcester Part No. 7 719 001 891
VERTICAL BF KIT
(125MM DIA)
Worcester Part No. 7 719 002 349
HORIZONTAL FLUE KIT
(100MM DIA)
Worcester Part No. 7 719 001 892
VERTICAL FLUE ADAPTOR
(100MM DIA)
Worcester Part No. 7 719 002 430
VERTICAL FLUE ADAPTOR
(125MM DIA)
HORIZONTAL FLUE KIT
(125MM DIA)
Worcester also has a pre-sales department, which provides
assistance in selecting a boiler system to suit a particular application,
along with full guidance on installation. As well as this we will also
assist in finding a recommended installer. For more information
please contact the Technical Hotline or alternatively visit our website
where literature can be downloaded www.worcester-bosch.co.uk
Technical
Tel: 08705 266 241
Fax: 01905 752 741
Worcester Part No. 7 719 002 431
Worcester Part No. 7 719 002 345/497
Worcester Part No. 7 719 002 432
Note: For information on the Condensfit II Telescopic Flue System and Plume
Management Kit, please see dedicated flue Technical and Specification leaflet.
24
Worcester Part No. 7 719 002 433
Worcester Part No. 7 719 002 350
25
Opening Times
Monday – Friday: 8.00am – 6.00pm
Saturday: 8.30am – 1.00pm
BBT180 Gstar CDi T&S Iss B
4/5/06
12:50
Page 26
The very best training programmes
from Worcester
Distance Learning
Worcester has always placed great emphasis on technical support
and training for installers and service engineers. Today this need is
greater than ever. The differences between a combi, conventional
and condensing boiler are substantial, and the technology of each
continues to advance at a rapid pace.
Worcester has produced a selection of Distance Learning
CD ROMs/DVDs which are packed with information. Call 01905
752556 for your copies.
To ensure the highest levels of competence and expertise in the
installation of all Worcester products, the company runs intensive
training courses for installers, commissioning engineers and
engineers involved with servicing and fault finding.
Worcester
Training Courses
Greenstar CDi, Highflow 440 and HE Plus gas-fired
condensing combi boilers
Models covered
Duration
Get on course for a more profitable future now
Call now for more information
01905 752526
Courses available
Our training facilities offer a number of courses suitable for the
installer and commissioning engineers, and a more in-depth course
for the servicing and fault finding engineers.
Camray oil-fired combi, regular and system boilers
Models covered
Greenstar 25/30/35/40CDi
Greenstar Highflow 440
Greenstar 30/35/40 HE Plus
1 day
Duration
Greenstar i Junior and Si gas-fired condensing
combi boilers
Certificate in Energy Efficiency for Domestic
Heating Course
Models covered
Covering
Greenstar system and regular gas-fired
condensing boilers
Key elements of energy-efficient heating and hot water
systems and products, compliance with the latest
Building Regulations, how condensing boilers work
and how they differ to non condensing products.
Duration
1 day
Models covered
Unvented Cylinder Course
Duration
Duration
Greenstar 24/28i Junior
Greenstar 25/30Si
1 day
Greenstar 12/15/18/24Ri
Greenstar 30/40CDi Conventional
Models covered
Duration
Training Centres throughout the UK
Duration
Greenstar Heatslave
Greenstar Danesmoor
Greenstar Utility
1 day
Danesmoor and Heatslave oil-fired boilers
Models covered
In addition to the outstanding facilities at the company’s
headquarters in Worcester, there are centres at Clay Cross in
Derbyshire, Rochester in Kent, West Thurrock in Essex and Bangor,
Northern Ireland. A new centre is also due to open* in north west
England. There are also additional training opportunities available
throughout the UK. Please phone 01905 752526 for more
information about a course near you. Each course is run by specialist
trainers and is superbly equipped to deliver a combination of
classroom theory and practical hands-on experience that’s second
to none.
Duration
Danesmoor
Heatslave
1 day
OFTEC Training
OFTEC 101
Covering
Duration
Domestic/Light Commercial Pressure
Jet Commissioning and Servicing
3 day course (2 days training plus
1 days assessment)
OFTEC 105e
Covering
*Open Autumn/Winter 2006
New Product Advance Training
Duration
Domestic/Light Commercial Pressure
Jet Boiler installation
1 day assessment
OFTEC 101 & 105e
Exclusive to Business Initiative members, these invaluable courses
give you an introduction and insight into new Worcester products as
soon as they are released on to the market.
www.worcester-bosch.co.uk
Covering
Duration
College-linked learning
Domestic/Light Commercial Pressure Jet Installation,
Commissioning and Servicing
3 day course (2 days training plus 1 days
assessment comprising 2 theory and 1 practical)
OFTEC 600a
A number of the UK’s leading proactive technical colleges are
equipped with Worcester products and offer excellent practical
tuition on a more local level.
Covering
Duration
Oil Tank Installation and Associated Controls
1 day assessment course
OFTEC 101/105e/600e
Covering
Duration
26
All G3 Regulations for the Installation, Servicing
and Commissioning of Unvented Cylinders.
The course includes recognised accreditation by
Logic Certification.
Duration
1 day
Greenskies Solar System
24/28i Junior
24/28Si II
24/28/35CDi
1 day
Greenstar oil-fired condensing boilers
Models covered
Covering
Greenstar 30CDi System
Greenstar 12/24i System
1 day
Standard efficiency boiler course:
i/Si/CDi (non condensing)
Worcester’s network of regional training centres are strategically
located across the country to help put you within convenient
travelling distance of the courses you wish to attend.
External
Utility
System
Combi
1 day
Domestic/Light Commercial Pressure Jet Boiler
Installation, Commissioning, Servicing and Oil Tank
Installation and Associated Controls
4 days
(2 days training and 2 days assessment)
27
Covering
Installation, Commissioning and Servicing
Duration
1 day
Download PDF