User's Guide | ADLINK Technology NuDAQ / NuIPC LPCI-7200S User`s guide

Add to My manuals
43 Pages

advertisement

User's Guide | ADLINK Technology NuDAQ / NuIPC LPCI-7200S User`s guide | Manualzz

NuDAQ

®

ACLD Series

Termination Boards

User’s Guide

@Copyright 1995~2000 ADLINK Technology Inc.

All Rights Reserved.

Manual Rev. 2.32: June 7, 2000

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

NuDAQ is a registered trademark of ADLink Technology Inc.

Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Getting service from ADLINK

Customer Satisfaction is always the most important thing for ADLINK

Tech Inc. If you need any help or service, please contact us and get it.

ADLINK Technology Inc.

Web Site http://www.adlink.com.tw

Sales & Service [email protected]

Technical

Support

NuDAQ

NuDAM [email protected] [email protected]

NuIPC

NuPRO [email protected] [email protected]

TEL

Address

Software

AMB

+886-2-82265877 [email protected] [email protected]

FAX +886-2-82265717

9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235

Taiwan, R.O.C.

Please inform or FAX us of your detailed information for a prompt, satisfactory and constant service.

Detailed Company Information

Company/Organization

Contact Person

E-mail Address

Address

Country

TEL

Web Site

FAX

Questions

Product Model

Environment to Use OS

Computer Brand

M/B : CPU :

Chipset : Bios :

Video Card :

Network Interface Card :

Other :

Challenge Description

Suggestions for ADLink

Contents

Chapter 1 ACLD-9185............................................. 1

1.1 Introduction ................................................................... 1

1.1.1

Features.............................................................................................1

1.1.2

Specifications ..................................................................................2

1.2 Installation ..................................................................... 2

1.2.1

What you have.................................................................................2

1.2.2

ACLD-9185 Layout..........................................................................3

1.2.3

Power Source Setting....................................................................4

1.2.4

Connect to add-on card ................................................................5

1.3 Usage .............................................................................. 5

1.4 Connector Pin Assignments..................................... 6

1.5 Applications .................................................................. 6

Chapter 2 ACLD-9182A.......................................... 7

2.1 Introduction ................................................................... 7

2.1.1

Features.............................................................................................7

2.1.2

Specifications ..................................................................................8

2.2 Installation ..................................................................... 8

2.2.1

What you have.................................................................................8

2.2.2

ACLD-9182A's Layout....................................................................9

2.2.3

Connect to add-on card ................................................................9

2.3 Usage ............................................................................ 10

2.3.1

Input Mode Setting .......................................................................10

2.3.2

Adjust Threshold for Isolated Mode ........................................11

2.3.3

Customize the Current Limit Resistor.....................................11

2.4 Connector Pin Assignments................................... 12

Contents

• i

2.5 Applications ................................................................ 13

Chapter 3 ACLD-8125........................................... 14

3.1 Introduction ................................................................. 14

3.2 Installation ................................................................... 14

3.2.1

What you have...............................................................................15

3.2.2

ACLD-8125 Layout........................................................................15

3.2.3

Connect to add-on card ..............................................................16

3.3 How to use ACLD-8125............................................. 16

3.3.1

ACL-8125 Connections................................................................16

3.3.2

CJC Output Configurations........................................................17

3.3.3

Circuit Diagram of ACLD-8125 ..................................................18

3.4 Connector Pin Assignments................................... 19

3.5 Expamle for temperature measuring by using the ACL-8112 and ACLD-8125 ................................ 20

3.6 Applications ................................................................ 21

Chapter 4 ACLD-9178........................................... 22

4.1 Introduction ................................................................. 22

4.4.1

Features...........................................................................................22

4.2 Installation ................................................................... 22

4.2.1

What you have...............................................................................23

4.2.2

ACLD-9178 Layout........................................................................23

4.3 Signal Conditioning Circuits................................... 24

4.4 Pin Assignment .......................................................... 25

4.5 Applications ................................................................ 26 ii

• Contents

Chapter 5 ACLD-9188........................................... 27

5.1 Introduction ................................................................. 27

5.1.1

Features...........................................................................................27

5.2 Installation ................................................................... 28

5.2.1

What you have...............................................................................28

5.2.2

ACLD-9188 Layout........................................................................28

5.3 Signal Conditioning Circuits................................... 29

5.4 Pin Assignment .......................................................... 29

5.5 Applications ................................................................ 30

Chapter 6 ACLD-9138........................................... 31

6.1 Introduction ................................................................. 31

6.2 Installation ................................................................... 31

6.2.1

What you have...............................................................................31

6.2.2

ACLD-9138 Layout......................................................................32

6.3 Using the ACLD-9138................................................ 33

6.3.1

Signal Conditioning Circuits......................................................33

6.3.2

Power Indicator .............................................................................33

6.4 Applications ................................................................ 34

6.5 Pin Assignment .......................................................... 34

Product Warranty/Service...................................................... 35

Contents

• iii

How To Use This Guide

This manual is designed to help users to use the ADLink termination boards. The products described in this manual include:

Ø ACLD-9185

Ø ACLD-9182A

Ø ACLD-8125

Ø ACLD-9178

Ø ACLD-9188

Ø ACLD-9138

The manual describes how to modify settings on the daughter board to meet your applications.

Termination Applications for NuDAQ

Boards

ACLD-9185 PCI-9111 Series, ACL-8312/8316, ACL-8112 Series, ACL-

8216, ACL-6126,

ACL-7120

ACLD-9182A PCI-9111 Series, ACL-8312/8316, ACL-8112 Series, ACL-

8216, ACL-6126, ACL-7120

ACLD-8125 PCI-9112, PCI-9111 Series, ACL-8312/8316, ACL-8112

Series, ACL-8126

ACLD-9178 ACL-8312/8316, ACL-8216, ACL-6126, ACL-7120

ACLD-9188 PCI-9114 Series, PCI-9111 Series, PCI-6208 Series, PCI-

8133, PCI-7200, PCI-7230, PCI-7250/7251, ACL-8312/8316,

ACL-8112 Series, ACL-8216, ACL-8111, ACL-6126, ACL-

7130, ACL-9188, ACL-7225

ACLD-9138 PCI-9112, PCI-9111 Series, ACL-8312/8316, ACL-8112

Series, ACL-8216

1

ACLD-9185

This chapter describes how to install and use the ACLD-9185.

1.1 Introduction

The ACLD-9185 is a 16-channel SPDT form C relay output board. It provides 16 electromechanical SPDT relays, which can be used by any

ACL series or PCI series boards with digital output channels on 20-pin flat ribbon connector.

You can use the 16 on-board relays to control power switches. Each of them matches with one LED to indicate its ON/OFF status and consumes about 33mA when energized. When all relays on the board are active, the board takes about 0.53 A from the computer's 12 volts power supply.

When the current driving capability of the 12V power source is not enough, the ACLD-9185 has a jumper switch allowing the users to connect an external +12V power source.

1.1.1 Features

The ACLD-9185 Relay Actuator Card provides the following features: l 16 Single-Pole-Double-Throw relays l LED indicators to show activated relays l On-board relay driving circuits l 120V/1 Amp contact rating l Simple to program l Controlled through TTL/CMOS signals or digital output ports of any ACL and PCI series board

ACLD-9185

• 1

l Screw terminal for easily wiring

1.1.2 Specifications

Output Channels

Relay Type

Contact rating

Breakdown Voltage

Release time

Operate time

Relay ON time

Relay OFF time

Total switching time

Insulation Resistance

Life Expectancy

Power Consumption

Power supply

Size

Connectors

16

16 SPDT ( Form C )

120V AC/DC, 1A

1000V AC/DC min..

5 msec max.

5 msec max..

3 msec typical

3 msec typical

10 msec typical

100 mega Ohms min.

> 5 million operations at full load

+12V , 33mA for each relay, total 0.53A if all relay are energized +5V, less than 0.2A

+12V from the PC-Bus

203 mm X 132mm

20-pin flat cable

1.2 Installation

To install and operate the ACLD-9185, you can follow the following steps:

Ø Check what you have in the box

Ø Check the PCB

Ø Set jumper (set power source)

Ø Make connection to add-on cards

Ø Program the add-on cards

1.2.1 What you have

In addition to this User's Manual, the package includes the following items: l ACLD-9185 Relay Output Board l Cable l Nylon standoffs for table-top or panel mounting

If any of these items was missed or damaged, contact the dealer whom you purchased. Save the shipping materials and carton in case you want to ship or store the product in the future.

2

• ACLD-9185

1.2.2 ACLD-9185 Layout

CN3

+5V

+12V

CN4

NO0

NC0

COM0

K0

K1

NO7

NC7

COM7

K5

K6

K7

K2

K3

K4

CN1

K8

K9

K10

CN2

NO8

NC8

COM8

K11

K12

K13

K14

K15

NO15

NC15

COM15

ACLD-9185

• 3

1.2.3 Power Source Setting

The ACLD-9185's power source can come from internal source (provided from the PC bus via the CN1 20-pin connector) or external source

(provided by external power supply). The +5V is used to drive the TTL buffer circuits and the LED on board. The +12V is used to drive the

Relays. The description of power source is specified as following table:

Internal power

+12V

+5V

Provided by PC bus via the CN1 20-pin connector

External power

+12V

+5V

Provided by external DC source via connector CN3

The power sources can be selected by setting jumpers according to the following table.

I n t e r n a l + 5 V

I n t e r n a l + 1 2 V

(d e f a u l t )

+ 5 V

+ 1 2 V

E x t e r n a l + 5 V

E x t e r n a l + 1 2 V

+ 5 V

+ 1 2 V

I n t e r n a l + 5 V

E x t e r n a l + 1 2 V

+ 5 V

+ 1 2 V

E x t e r n a l + 5 V

I n t e r n a l + 1 2 V

+ 5 V

+ 1 2 V

4

• ACLD-9185

1.2.4 Connect to add-on card

The ACLD-9185 can be controlled with NuDAQ ISA or PCI add-on cards.

The configurations of connection are shown in the following diagram.

Please make sure to connect to the digital output port of the add-on cards with correct pin-assignment.

ACLD-9185

1.3 Usage

The function diagram of Form C relays on the ACLD-9185 is shown here.

NO NO

COM COM

NC NC

Control Bit = High (1) Control Bit = Low (0)

This relay has three contacts: NC (Normal Closed), NO (Normal Open), and COM (Common). The COM post, located at the middle, can make contact either NO post or NC post. When the control bit is high (1), the

COM post and NO post are contacted. If the control bit is low (0), the

COM post and NC post make contact.

In normal power-up and reset, the relay is in low status.

ACLD-9185

• 5

1.4 Connector Pin Assignments

The relationship between connector pins, relay contacts, LED's, and on the ACLD-9185 is shown in the following table:

CN1

PIN

RELAY RELAY Contacts LED

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

K8

K9

K10

K11

K12

K13

K14

K15

K0

K1

K2

K3

K4

K5

K6

K7

COM0 NC0 NO0

COM1 NC1 NO1

COM2 NC2 NO2

COM3 NC3 NO3

COM4 NC4 NO4

COM5 NC5 NO5

COM6 NC6 NO6

COM7 NC7 NO7

COM8 NC8 NO8

COM9 NC9 NO9

COM10 NC10 NO10

COM11 NC11 NO11

COM12 NC12 NO12

COM13 NC13 NO13

COM14 NC14 NO14

COM15 NC15 NO15

Ground

Ground

+5 DC

+12 DC

8

9

10

11

12

13

14

15

0

1

2

3

4

5

6

7

1.5 Applications

The ACLD-9185 could be used on our following products:

ü PCI-9111Series

ü PCI-9112

ü ACL-8312/8316

ü ACL-8112 Series

ü ACL-8216

ü ACL-6126, ACL-7120

6

• ACLD-9185

2

ACLD-9182A

This chapter describes how to install and use the ACLD-9182A.

2.1 Introduction

The ACLD-9182A is a 16-channel opto-isolated digital input board, which can be connected by any ACL or PCI series digital input board with D/I channels of 20-pin flat ribbon connectors. It is a good solution for preventing floating potential and ground loop problems.

Each input channel has a red LED to indicate the ON/OFF status. If the input voltage is high, the LED will be on otherwise the LED is off. AC or

DC input is selectable by setting the jumpers. And you do not need to care the polarity.

2.1.1 Features l 16 Opto-Isolated digital input channels l For use with 20-pin digital input connector of NuDAQ cards l AC or DC polarity-free digital input l Screw terminals for easy wiring l On board LEDs to indicate the input logic status

ACLD-9182A

• 7

2.1.2 Specifications

Number of channel

Opto-coupler

Input impedance

Threshold voltage

Isolation voltage

Input mode

Response time

Connector

Screw Terminal

Indication Display

Size

16

4N35

1.2K ohm

1.5 VDC

1000 VDC(channel to channel and channel to ground)

Isolation and dry contact input range

20uSec without AC filter

20-Pin Flat Ribbon Cable

Connector

5m m wiring spacing, 18-22 AWG

16 LEDs

205 mm X 114 mm

2.2 Installation

To install and operate the ACLD-9182A, please follow the following steps:

Ø Check what you have in the box

Ø Check the PCB

Ø Make connection to add-on cards

Ø Program the add-on cards

2.2.1 What you have

In addition to this User's Manual, the package includes the following items: l ACLD-9182A Photo coupler input Board l Cable l Nylon standoffs for table-top or panel mounting

If any of these items was missed or damaged, contact the dealer whom you purchased. Save the shipping materials and carton in case you want to ship or store the product in the future.

8

• ACLD-9182A

2.2.2 ACLD-9182A's Layout

+12V

+5V

+15-

+14-

+13-

+12-

+11-

+10-

+9-

+8-

TB2

JA15 JB15

JA14

JA13

JB14

JB13

JA12 JB12

JA11 JB11

JA10

JA9

JB10

JB9

JA8 JB8

CN1

JB7

JB2

JB1

JB0

JB6

JB5

JB4

JB3

JA7

GND

JA6

GND

JA5

+7-

JA4

+6-

JA3 +5-

JA2 +4-

JA1 +3-

JA0 +2-

+1-

+0-

TB1

2.2.3 Connect to add-on card

The ACLD-9182A can be controlled with NuDAQ ISA or PCI add-on cards.

The configurations of connection are shown in the following diagram.

Please make sure to connect to the digital output port of the add-on cards with correct pin-assignment.

ACLD-9182

ACLD-9182A

• 9

2.3 Usage

By setting the JAn and JBn jumpers, you can choose the isolated or dry input(see the 2.3.1). And adjust threshold for isolated mode by tuning

VR1(see 2.3.2).

2.3.1 Input Mode Setting

There are 2 jumpers (JAn and JBn, n = 0 ~ 15) associated with each digital input channel for configuring the channel as isolated or nonisolated (Dry Contact) input. The digital input channels and their corresponding jumper is shown below.

Each channel comes equipped with a pair of jumpers for either isolated or non-isolated selection. If the jumper plugs are installed on the upper posts of JAn, and JBn (n =0..15), the channel n is configured as

ISOLATED, otherwise the jumper plugs should be installed on the lower posts to configure as Non-isolated.

For channel 0~7 (n=0..7)

Isolated Non-isolated Input Signal

Selection

JAn

JBn

I

I

I

I

For channel 8~15 (n=8..15)

Input Signal

Selection

JAn

JBn

Isolated Non-isolated

N

10

• ACLD-9182A

2.3.2 Adjust Threshold for Isolated Mode

The input isolated mode of the ACLD-9182A is actually driven by current instead of voltage level. The logic low means the input leakage current should be less than 1mA, otherwise the input status will be treated as logic High (1).

To avoid the logic high voltage as low, the ACLD-9182A is equipped with a variable resistor VR1, which is used to adjust the threshold level for all the 16 isolated input channels.

RV

DIn+

4K +5V

DIn-

Adjusting procedures:

1 Apply a +5V voltage source at DIH and DIL along with a 4K Ohms resistor. The resistor limits input current to about 1mA.

2 Adjust the VR1 until the LED0 is off.

Follow the adjusting procedures, if channel 0's input voltage is low, and the input leakage current is less than 1mA, the input status is considered as logical low (TTL 0). To prevent higher input leakage current, you can change the 3.9K Ohms resistor by a lower one, and use the above procedures to meet your requirements.

2.3.3 Customize the Current Limit Resistor

The default voltage input range of the ACLD-9182A is from 0V to 24V. To accept higher voltage input, you should replace the current limit resistor,

RA0...RA15, for each channel.

The current rating of the 4N35 photocoupler is about 60mA. It is recommended that the input current is within 20mA. If you want to choose the proper current limit resistor, please use the following formula to calculate the input current( IF).

Vin = I

F X Ri

Pw = Vin X I

F

ACLD-9182A

• 11

Where

Vin : Input voltage

I F : Input current

Pw : Power rating

Ri : Current Limit resistor

For example:

If the input voltage is 40V, then the maximum input current is within

20mA, using the above formula :

Ri = 40 (V) / 20 (mA) = 2 K

Pw = 40 (V) X 20 (mA) = 0.8 W

You should choose a 2K

resistor and the power rating of this resistor should be 1 Watt.

2.4 Connector Pin Assignments

The relationship between connector CN1's pins (below), terminal blocks

(TB1 & TB2), LED's, and their related jumpers are shown in the following table :

CN1 PIN

NO.

D/I

Channel

TB1 & TB2

LABEL

LED

NO.

RELATED

JUMPER

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

** 20

DI 6

DI 7

DI 8

DI 9

DI 10

DI 11

DI 12

DI 13

DI 14

DI 15

DI 0

DI 1

DI 2

DI 3

DI 4

DI 5

TB1 0+,0-

TB1 1+,1-

TB1 2+,2-

TB1 3+,3-

TB1 4+,4-

TB1 5+,5-

TB1 6+,6-

TB1 7+,7-

TB2 8+,8-

TB2 9+,9-

TB2 10+,10-

TB2 11+,11-

TB2 12+,12-

TB2 13+,13-

TB2 14+,14-

TB2 15+,15-

GND

GND

+5V

+12V

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

JA0, JB0

JA1, JB1

JA2, JB2

JA3, JB3

JA4, JB4

JA5, JB5

JA6, JB6

JA7, JB7

JA8, JB8

JA9, JB9

JA10, JB10

JA11, JB11

JA12, JB12

JA13, JB13

JA14, JB14

JA15, JB15

12

• ACLD-9182A

** Pin-20 (+12V) depends on the output form digital input connector, such as ACL-8111, ACL-8112 are +12V , but it is strobe signal on ACL-7120.

2.5 Applications

The ACLD-9182A could be used on following products:

ü PCI-9111 Series

ü ACL-8312/8316

ü ACL-8112 Series

ü ACL-8216,

ü ACL-6126

ü ACL-7120.

ACLD-9182A

• 13

3

ACLD-8125

This chapter describes how to install and use the ACLD-8125.

3.1 Introduction

The ACLD-8125 is a signal conditioning termination board with build-in cold junction temperature sensor. It has the following features:

Ø On board signal conditioning circuits for every analog input channels

Ø Cold junction temperature sensor

Ø Build-in screw terminals for wiring

Ø 37-pin D-sub connector

3.2 Installation

To install and operate the ACLD-8125, pleas e follow the following steps:

Ø Check what you have in the box

Ø Check the PCB

Ø Make connection to add-on cards

Ø Program the add-on cards

14

• ACLD-8125

3.2.1 What you have

In addition to this User's Manual, the package includes the following items: l ACLD-8125 Signal Conditioning Termination Board l Cable l Nylon standoffs for table-top or panel mounting

If any of these items was missed or damaged, contact the dealer whom you purchased. Save the shipping materials and carton in case you want to ship or store the product in the future.

3.2.2 ACLD-8125 Layout

ACLD-8125

• 15

3.2.3 Connect to add-on card

The ACLD-8125 can be used with NuDAQ ISA or PCI add-on cards. The configurations of connection are shown in the following diagram. Please make sure to connect to the digital output port of the add-on cards with correct pin-assignment.

ACLD-8125

3.3 How to use ACLD-8125

3.3.1 ACL-8125 Connections

The ACL-8125 comes equipped with a DB-37 female connector; this board is designed for ACL-8112/8216/8316 and PCI-9111/9112 series cards for convenient wiring. This board provides two kinds of wiring style: single-ended and differential. The connections are illustrated as following figures.

(1) Single-ended connection

R A O

AIOH

AIO

AGND

RBO C O

A G N D

(2) Differential connection

R A O

AIOH

G H O H

C C O

AIOL

RDO

C H O L

16

• ACLD-8125

3.3.2 CJC Output Configurations

An on-board Cold Junction Compensation (CJC) circuit is provided by the

ACLD-8125 for thermcouple measurement. The CJC is connected with

Channel 0 of the internal connector. The circuit of CJC and CH0 is shown as following:

The jumper setting for CJC outp ut configuration are as following:

(1) Fully Differential Single-ended with CJC

C I O H

J P 1 : 1 - 2

J P 2 : 1 - 2

C H O L

J P 1

1

2

3

J P 2

1

2

3

C H O H

C H O L

CJC

C irc u itry

(2) Single-ended with CJC

A I O L

J P 1 : 1 - 2

J P 2 : 2 - 3

A I 8

(3) Disable CJC

J P 1

1

2

3

J P 2

1

2

3

A I O

A I 8

CJC

C J C

Circuits

A IO H

A IO

A I L O

A I8

J P 1

1

2

3

J P 2

1

2

3

C H O H

A IO

C H O L

A I8

J P 1 : 2 - 3

J P 2 : 2 - 3

ACLD-8125

• 17

3.3.3 Circuit Diagram of ACLD-8125

(1) CJC Circuit

AI0

RA0

0

RB0

USER C0

USER

RD0

USER

CD0 USER

2

JP1

AIH0

AI8

RA8

0

RB8

USER C8

USER

JP2

2 AIL8

+12V

D2

LM334

2

VR1

10K

R16

68.1%1

3

D1

LM335

(2) Signal Conditioning Circuit

AI1

RA1

0

AIH1

RD1

USER

CD1 USER

AI9

RA9

0

AIL9

RB1

USER C1

USER

RB9

USER C9

USER

18

• ACLD-8125

3.4 Connector Pin Assignments

Pin assignment of CN1

Pin Description

6

7

8

9

1

2

3

4

5

AIH0

AIH1

AIH2

AIH3

AIH4

AIH5

AIH6

AIH7

AGND

10

11

12

13

14

15

16

17

AGND

VREF

EXTREF2

+12V

AGND

DGND

CNT0_OUT

EXT_TRG

18

19

Pin Assignment of CN2A

Pin

1

2

NC

VCC

3

4

5

6

7

8

9

10

11

12

Description

AGND

AI14

AI6

AGND

AI12

AI4

AGND

AI10

AI2

AGND

AI8

AI0

25

26

27

28

29

30

31

32

33

34

35

36

37

Pin

20

21

22

23

24

Description

AIL8

AIL9

AIL10

AIL11

AIL12

AIL13

AIL14

AIL15

AGND

AGND

AO1

EXTREF1

AO2

CNT0_GATE

GATE

NC

NC

CNT0_CLK

ACLD-8125

• 19

Pin Assignment of CN2B

Pin

1

2

3

4

5

6

7

8

9

10

11

12

Pin Assignment of CN3

Pin

5

6

7

8

9

10

11

1

2

3

4

12

13

14

Description

AGND

AI15

AI6

AGND

AI13

AI5

AGND

AI11

AI3

AGND

AI9

AI1

Description

VREF

AO1

EXTREF1

AGND

EXTREF2

AGND

CNT0_CLK

CNT0_GATE

CNT0_OUT

DGND

GATE

EXT_TRG

DGND

VCC

3.5 Expamle for temperature measuring by using the ACL-8112 and ACLD-8125

There is an on-board CJC circuit. The CJC is connected with Channel 0 of the internal connector. It can be used for obtaining environment temperature.

1) ACLD-8125 JP1 : 1+2 JP2 : 2+3

2) ACL-8112 JP9 : +/- 5V range

20

• ACLD-8125

3) Now you can read the CJC voltage by reading channel 0 of ACL-8112

4) If the environment temperature is 25 degree. The voltage you read is about 2.98 V

5)

V(mV)=T('K)*10(mV/'K)

T('K)=T('C)+273('K)

2.98V=2980mV=(25+273)*10mV

when the JP9 on the ACL-8112 is +/-5V range.

3.6 Applications

The ACLD-8125 could be used on following products:

ü PCI-9112

ü PCI-9111 Series

ü ACL-8312/8316

ü ACL-8112 Series

ü ACL-8216.

ACLD-8125

• 21

4

ACLD-9178

This chapter describes how to install and use the ACLD-8125.

4.1 Introduction

The ACLD-9178 is a universal screw terminal panel with convenient connection points for 20-pin flat cable connector.

The ACLD-9178 is designed for establishing external signal conditioning circuits. For example, you can easily construct a low-pass filter, attenuator or current-to-voltage converter by adding resistors and capacitors onto the reserved circuit pads.

4.4.1 Features

The ACLD-9178 screw terminal board provides the following features: l Low cost universal screw terminals l Signal conditioning circuits built-in. l Table-top mounting using nylon standoffs l 40 terminal points for two 20-pin flat cable connectors. l Controlled through TTL/CMOS signals or digital output ports of any ACL series board

4.2 Installation

To install and operate the ACLD-9178, please follow the steps:

Ø Check what you have in the box

22

• ACLD-9178

Ø Check the PCB

Ø Make connection to add-on cards

Ø Program the add-on cards

4.2.1 What you have

In addition to this User's Manual, the package includes the following items: l ACLD-9178 Screw Terminal Board l Cable l Nylon standoffs for panel mounting.

If any of these items was missed or damaged, contact the dealer whom you purchased. Save the shipping materials and carton in case you want to ship or store the product in the future.

4.2.2 ACLD-9178 Layout

CNB

CNA

Signal

Conditioning

Circuits A18

A16

A14

A12

A10

A08

A06

A04

A02

B20

B18

B16

B14

B12

B10

B08

B06

B04

B02

A20

A17

A15

A13

A11

A09

A07

A05

A03

A01

B19

B17

B15

B13

B11

B09

B07

B05

B03

B01

A19

ACLD-9178

• 23

4.3 Signal Conditioning Circuits

The ACLD-9178 is suitable for specifically passive signal conditioning components. The following circuits are examples of signal conditioning for screw connector A1 and A2.

Flat cable

1

R1A

R1B C1 connector

2

Ø Straight-through connection (Default setting)

A1

Screw

A2

Terminal

1 A1

2

R1A = Short ( 0

)

R1B and C1 = Open

Ø Single-ended Voltage Attenuator

1

R1B

2

R2A = Short( 0

), C1 = Open,

Attenuation = R1B / ( R1A + R1B)

Example : 10: 1 voltage attenuator

R1A = 9K

, and R1B = 1K

Attenuation = 1 / (1 + 9)

R1A

I

A2

A1

A2

24

• ACLD-9178

Ø Low-pass filter (Single-ended Input)

1

C1

R1A

A 1

2

R2A = Short ( 0

), R1B = Open

ƒ

3dB = 1 / ( 2

π

R1A C1)

Example : 1.6 KHz low pass filter:

R1A = 10K

, C1 = 0.01

µ

F

Ø 0-20mA Current-loop Input

A 2

1 A 1

R1B

I

2 A 2

R1A = Short( 0

), C1 = Open,

R1B = 250

( 0.05% tolerance) for 0 to 5V VDC signal Converter.

4.4 Pin Assignment

Pin assignment of CAN

Pin Description

1

2

3

4

5

6

A1

A2

A3

A4

A5

A6

7

8

9

10

A7

A8

A9

A10

Pin

11

12

13

14

15

16

17

18

19

20

Description

A11

A12

A13

A14

A15

A16

A17

A18

A19

A20

ACLD-9178

• 25

Pin assignment of CNB

Pin Description

1

2

3

4

5

6

7

8

9

10

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

Pin

11

12

13

14

15

16

17

18

19

20

4.5 Applications

The ACLD-9178 could be used on following products:

ü ACL-8312/8316

ü ACL-8216

ü ACL-6126

ü ACL-7120

Description

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

26

• ACLD-9178

5

ACLD-9188

This chapter describes how to install and use the ACLD-9138.

5.1 Introduction

The ACLD-9188 is a universal screw terminal board, which provides convenient connection points for 20-pin flat ribbon cable or shielded cable with 37-pin D-type connector. This panel is designed for field signal wiring in industrial applications.

For example, you can easily construct a low-pass filter, attenuator or current-to-voltage converter by adding resistors and capacitors onto the reserved circuit pads.

5.1.1 Features

The ACLD-9188 industrial terminal board provides the following features: l Low cost universal screw terminals l Black pads accommodate applications such as break detection, low-pass filter, current shut and voltage attenuator. l Industrial type terminal blocks permit heavy-duty and reliable connection of signals. l 40 screw terminal points for two 20-pin flat cable or DB-37 connectors.

ACLD-9188

• 27

5.2 Installation

5.2.1 What you have

In addition to this User's Manual, the package includes the following items: l ACLD-9188 Industrial Terminal Board l Cable l Nylon standoffs for table-top or panel mounting.

If any of these items was missed or damaged, contact the dealer whom you purchased. Save the shipping materials and carton in case you want to ship or store the product in the future.

5.2.2 ACLD-9188 Layout

-

D

B

C

N

C

N

C

N

C

N

28

• ACLD-9188

5.3 Signal Conditioning Circuits

The signal conditioning circuits of ACLD-9188 is the same as the circuits on ACLD-8125. Please refer to Section 4.3 for details.

You can connect the card and this terminal board with a DB-37 cable. The

CN3 and CN1 are connected together, and so are the CN2 and CN4. If your application is sensitive signal, we suggest that please do not use flat cable connector and screw connector at the same time.

5.4 Pin Assignment

A1 to A20 is CN1.

B1 to B20 is CN2.

For example, the first field of the table means that A1(CN3-1), CN1-1,

CN5-1 are connected together.

A1 CN1-1 CN5-1

A2 CN1-2 CN5-20

A3 CN1-3 CN5-2

A4 CN1-4 CN5-21

B1 CN2-1 CN5-11

B2 CN2-2 CN5-30

B3 CN2-3 CN5-12

B4 CN2-4 CN5-31

A5 CN1-5 CN5-3

A6 CN1-6 CN5-22

A7 CN1-7 CN5-4

A8 CN1-8 CN5-23

A9 CN1-9 CN5-5

A10 CN1-10 CN5-24

A11 CN1-11 CN5-6

A12 CN1-12 CN5-25

A13 CN1-13 CN5-7

A14 CN1-14 CN5-26

A15 CN1-15 CN5-8

A16 CN1-16 CN5-27

A17 CN1-17 CN5-9

A18 CN1-18 CN5-28

A19 CN1-19 CN5-10

A20 CN1-20 CN5-29

B5

B6

B7

B8

B9

B10

B11

B12

B13

B14

B15

B16

B17

CN2-5

CN2-6

CN2-7

CN2-8

CN2-9

CN5-13

CN5-32

CN5-14

CN5-33

CN5-15

CN2-10 CN5-34

CN2-11 CN5-16

CN2-12 CN5-35

CN2-13 CN5-17

CN2-14 CN5-36

CN2-15 CN5-18

CN2-16 CN5-37

CN2-17 CN5-19

B18 CN2-18 -

B19 CN2-19 -

B20 CN2-20 -

ACLD-9188

• 29

5.5 Applications

The ACLD-9188 could be used on following products:

ü PCI-9114 Series

ü PCI-9111 Series

ü PCI-6208 Series

ü PCI-8133,

ü PCI-7200

ü PCI-7230

ü PCI-7250/7251

ü ACL-8312/8316

ü ACL-8112 Series

ü ACL-8216

ü ACL-8111

ü ACL-6126

ü ACL-7130

ü ACL-7225.

30

• ACLD-9188

6

ACLD-9138

This chapter describes how to install and use the ACLD-9138.

6.1 Introduction

The ACLD-9138 is an universal screw terminal board with 16 singleended channels on board signal conditioning circuit. It could be used on our PCI and ACL series cards. There is a DB-37 connector. You can add your signal conditioning circuits on it. It provides the following features:

Ø 16 single-ended channels with on board signal conditioning circuits(pin

1-8, 20-27).

Ø Build-in screw terminals for wiring

Ø 37-pin D-sub connector

Ø On board LED for power status.

6.2 Installation

6.2.1 What you have

In addition to this User's Manual, the package includes the following items: l ACLD-9138 Industrial Terminal Board l Two 20-pin 1-meter flat cable

If any of these items was missed or damaged, contact the dealer whom you purchased. Save the shipping materials and carton in case you want to ship or store the product in the future.

ACLD-9138

• 31

6.2.2 ACLD-9138 Layout

Power

Indicator

DB-37 connector

32 • ACLD-9138

Signal

Conditioning

Circuits

Screw Terminal

6.3 Using the ACLD-9138

6.3.1 Signal Conditioning Circuits

The signal conditioning circuits of ACLD-9138 is almost the same as

ACLD-8125 and ACLD-9178. But the ACLD-9138 supports only singleended connection, that means all your grounds are connected together.

Please refer to Section 4.3 for details.

RA0

0

Screw Terminal RB0

C0

USER

DB-37

Connector

Please note that RA0 is a 0-ohm resistor. You can also change its value for different applications.

6.3.2 Power Indicator

There are on board power indicator.

D1

CN1_19

R1

CN1_15

LED

The power LED is crossed between pin 19 and 15 of the DB-37 connector.

And the pin 9, 10, 28, 29 are connected to the external ground (GND of the screw terminal).

RG1

0 / NU

CN1_9

RG2

0 / NU

CN1_28

RG3

0 / NU

CN1_10

RG4

0 / NU

CN1_29

If your application is not been listed in section 6.4, you should take care about six pins listed above.

ACLD-9138

• 33

6.4 Applications

The ACLD-9138 could be used with the following products:

ü PCI-9112

ü PCI-9111 Series

ü ACL-8312/8316

ü ACL-8112 Series,

ü ACL-8216.

6.5 Pin Assignment

CN1

27

9

28

10

29

11

30

12

5

24

6

25

7

26

8

1

20

2

21

3

22

4

23

31

13

32

14

33

15

34

16

35

17

36

18

37

19

AI0

AI8

AI1

AI9

AI2

AI10

AI3

AI11

AI4

AI12

AI5

AI13

AI6

AI14

AI7

AI15

CN1_9

CN1_28

CN1_10

CN1_29

CN1_11

CN1_30

CN1_12

CN1_31

CN1_13

CN1_32

CN1_14

CN1_33

CN1_15

CN1_34

CN1_16

CN1_35

CN1_17

CN1_36

CN1_18

CN1_37

CN1_19

8

9

10

11

12

13

14

Pin

1

2

3

4

5

6

7

15

16

17

18

19

Meaning

AI0

AI1

AI2

AI3

AI4

AI5

AI6

AI7

CN1_9

CN1_10

CN1_11

CN1_12

CN1_13

CN1_14

CN1_15

CN1_16

CN1_17

CN1_18

CN1_19

27

28

29

30

31

32

33

Pin

20

21

22

23

24

25

26

34

35

36

37

34 • ACLD-9138

Meaning

AI8

AI9

AI10

AI11

AI12

AI13

AI14

AI15

CN1_28

CN1_29

CN1_30

CN1_31

CN1_32

CN1_33

CN1_34

CN1_35

CN1_36

CN1_37

Product Warranty/Service

Seller warrants that equipment furnished will be free from defects in material and workmanship for a period of one year from the confirmed date of purchase of the original buyer and that upon written notice of any such defect, Seller will, at its option, repair or replace the defective item under the terms of this warranty, subject to the provisions and specific exclusions listed herein.

This warranty shall not apply to equipment that has been previously repaired or altered outside our plant in any way as to, in the judgment of the manufacturer, affect its reliability. Nor will it apply if the equipment has been used in a manner exceeding its specifications or if the serial number has been removed.

Seller does not assume any liability for consequential damages as a result from our products uses, and in any event our liability shall not exceed the original selling price of the equipment.

The equipment warranty shall constitute the sole and exclusive remedy of any Buyer of Seller’s equipment and the sole and exclusive liability of the

Seller, its successors or assigns, in connection with equipment purchased and in lieu of all other warranties expressed implied or statutory, including, but not limited to, any implied warranty of merchant ability or fitness and all other obligations or liabilities of seller, its successors or assigns.

The equipment must be returned postage-prepaid. Package it securely and insure it. You will be charged for parts and labor if you lack proof of date of purchase, or if the warranty period is expired.

Product Warranty/Service

• 35

advertisement

Related manuals