advertisement
RCS - 433T
ST
GET
ARTED
RCS
Thank you for choosing a RCS product. You are recommended to read this manual carefully before installing the product.
CONTENTS
1 - TRANSMITTER INTRODUCTION
1A - General information
1B - Technical specifications
1C - Main features
2 - CODING
3 - MEMORIZATION
4 - BATTERY ACCESS
5 - TROUBLESHOOTING
1A - General information
The radiocontrol RCS-433T has been designed for the programmable telephone entry systems, anti-burglar systems and access control systems.
It has a very high security coding system. (KeeLoq ® Hopping code).
The code sent by the transmitter changes at each activation, avoiding any scanning and copying risk. A special algorithm
Push-button B allows to keep synchronyzed transmitter and receiver.
The operating frequency is 433,92 MHz.
The receiver RCS-433R type SELWR433, which operates with this transmitter, has a Wiegand 26 bit format output, suitable with any type of access control system, equipped with this type of protocol.
The CR 2016 lithium batteries have a life of about 18 months.
The product fully complies with the European Directives
99/5/CE, 89/336/CEE, 73/23/CEE and with the Part 15 of FCC
Regulations.
1B - Technical specifications
Number of keys:
Supply :
Battery life:
Current consumption :
Operating frequency :
Code combinations :
Modulation :
Rated e.r.p. :
Range in free space:
Operating temperature:
Overall dimensions:
Weight:
1C - Main features
Push-button A
2
2 lithium batteries CR 2016
18 - 24 months
13 mA
433.92 MHz
2 64
AM / ASK
50 - 100 mW
100 - 200 m
-20 ¸ +55 °C
61 x 36 x 16 mm
20 gr.
Red
LED
Battery door
Key holder ring
2 - CODING
Each transmitter is manufactured and sold with a different univocal serial number set-in-factory. The real transmitted code is the result of a special algorithm which combines a serial number, a manufacturer key and a synchronization number.
RCS-433T - Type : SETR2641AM2
FCC ID : PWJ T433
This device complies with Part. 15 of the FCC Rules
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept interference received, including interference that may cause undesired operation.
3 - MEMORIZATION
The transmitter security code has to be stored onto the receiver or the receivers memory available. Your own installer or reseller will perform this operation during the installation or will give you the necessaries instructions during the selling.
Notice
Any changes or modification to RCS equipment not expressly approved by RCS could void the user's authority to operate the equipment.
4 - BATTERY ACCESS
To access the battery turn clockwise the battery door.
Place the 2 lithium CR2016 batteries inserting a part of them under the door and taking care to push them just on the internal ring plane.
NOTE: Please dispose of the batteries correctly, they are hazardous waste.
GUARANTEE
The guarantee period of all RCS transmitter batteries is 6 months, beginning from the manufacturer date. During this period, if the product does not work correctly, due to a defective component, the product will be repaired or substituted at the discretion of the producer.
The guarantee does not cover the plastic container integrity.
5 - TROUBLESHOOTING
FAULT SOLUTION
The radio emission isn’t verifiable
The transmitter led is OFF.
Replace the transmitter batteries
The radio emission isn’t verifiable
The transmitter led is ON.
Check the receiver supply.
REMOTE CONTROL SOLUTIONS
College Park Commerce Center
2042 N. Rio Grande Ave. Suite A
Orlando - FL 32804
U.S.A.
Office: (407)-426-8687
Fax: (407)-428-9309 e-mail: [email protected]
The transmitter led blinks
Replace the transmitter batteries
IS-TMWGXUK2 Rev. 1 del 12.12.2001
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project