Worksaver | PALLET FORK PF-448 | Category I Attachments - Edney Distributing Co. Inc.

Designed. Engineered. Remarkable Value.
SARG — Sweep Action Rock Grapple
Handling Rocks and So Much More
Worksaver is taking a different approach to material handling needs.
www.worksaver.com
Engineered, Designed and Manufactured in the USA
Patent Pending
SARG Sweep Action
Rock Grapple
Revolutionizing the way rock
grapples work, the SARG
(Sweep Action Rock Grapple)
from Worksaver makes life easier.
With its patent pending design,
the SARG allows the operator to
own one tool to sort large or small
debris, resulting in low cost of
ownership. The front grapple
operates in a sweeping action to
pull rock or debris into the unit.
Grapple design retains the rocks
or debris, allowing the operator to
rock the attachment to sift dirt out
of the material. Rocks, brush, logs,
stumps, debris or scrap, the SARG
handles them all.
The SARG with its 66 degree of sweep
allows the operator to move rocks of
varying sizes into the bucket. The sweep
clamp operates like a thumb moving
material into and retaining it in the bucket.
Bolt-on side plates hold smaller rocks in the
bucket. They can be removed from the bucket
to allow the SARG to handle logs and stumps.
Model
SARG-72
SARG-84
Overall Width (in/mm)
72 / 1829
84 / 2134
Bucket Depth (in/mm)
34 / 864
34 / 864
Upper Grapple Width (in/mm)
34 / 864
40 / 1016
Grapple Opening (in/mm)
45 / 1143
45 / 1143
Tine Diameter (in/mm)
1.25 / 31.75
1.25 / 31.75
Weight (lbs/kg)
1194 / 542
1375 / 624
Product No.
812120
812160
Caution — A heavy load can cause your tractor to tip over. When moving heavy loads, keep the load
as close to the ground as possible, go slowly around turns, and be sure the front or rear of power unit is properly
counterbalanced with weights.
Caution — Operators must read & understand operator’s manual, particularly the safety warnings and instructions.
The operator is responsible for safety of themselves and others when operating equipment.
WORKSAVER, INC. has a corporate policy of continuous product improvement and development; therefore, specifications are subject to change without any advance notice.
WORKSAVER, INC. is not responsible for differences between specifications or illustrations
contained in this publication and the actual equipment.
Distributed by:
Worksaver, Inc.
P.O. Box 100, Litchfield, IL 62056-0100
Phone: 217-324-5973 • Fax: 217-324-3356
www.worksaver.com • E-mail: sales@worksaver.com
Designed. Engineered. Remarkable Value.
Form No. 124-6927
© 2014 Worksaver, Inc.
Printed in U.S.A.
Worksaver.
Designed.
Engineered.
Remarkable
Value.
WORKSAVER®
3 POINT ADAPTER for SKID STEER
Mounts easily to Skid Steer to permit the use of
Category I attachments
Worksaver
3 Point Adapter for Skid Steer
3 POINT ADAPTER SPECIFICATIONS
Attachments accepted ............................................................Category I
Mounting...............................................................................“Universal” Skid Steer
Quick Attach Mount
Construction.......................................................................... Heavy-Duty Welded Steel
Adapter width (in/mm) .......................................................... 44-1/2 (1130 mm)
Adapter height (in/mm) .........................................................18-3/4 (476 mm)
Lug spacing inside to inside (in/mm) ......................................27-1/8 (689 mm)
Lug spacing outside to outside ................................................29-5/8 (752 mm)
Shipping weight (lb./kg) ........................................................174 / (79 kg)
Product Computer Number ..................................................862865
•
•
•
•
Engineered for Skid Steers with
“universal” quick attach system.
Allows the use of category I
attachments.
Increase versatility of Skid Steer
without purchasing additional
attachments.
One set of adapter bushings is
supplied.
READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE OPERATION.
Worksaver Inc. has a corporate policy of continuous product improvement and development;
therefore, specifications are subject to change without any advance notice. Worksaver Inc. is not
responsible for differences between specifications or illustrations contained in this publication and
the actual equipment.
Worksaver.
Designed.
Engineered.
Remarkable
Worksaver,
Inc.
Value.
P.O. Box
100, Litchfield, IL 62056-0100
Phone: 217-324-5973 • Fax: 217-324-3356
E-mail: sales@worksaver.com
Web: www.worksaver.com
Information Provided By:
Worksaver.
Designed.
Engineered.
Remarkable
Value.
WORKSAVER®
Pallet Fork Attachments
Pallet Forks for Skid Steers and Tractor Front Loaders.
 Available for tractor loaders, skid
steers, and compact tractors.
 2,000 lb. to 5,500 lb. capacity.
 All models feature tapered solid
steel alloy forks for long life.
 Premium forks include spring
loaded latches (except ULF-2046)
for easy adjustment spacing.
 Models available with integrated
brackets for skid steers, John
Deere 400/500/600/700 series
loaders, and loaders with global
attaching method.
 Optional interfacing quick-attach
brackets available for most other
loader models.
 Skid steer pallet forks have stepthrough design for easy cab access
and excellent visibility.
 Skid steer models are designed to
mount to any skid steer with the
“Universal” quick-attach mounting
system.
 Provides versatility for your skid
steer or tractor front loader.
 Three models of clamp-on bucket
forks, 1,000-4,000 lbs.
Worksaver
Pallet Fork Specifications
For Skid Steer Loaders & Tractor Front Loaders With The “Universal “
For Tractor Loaders
For Compact
Quick Attach System
Tractor Loaders
SSPF-442
SSPF-448
PF-448
ULF-2046
Model
Skid Steer Loader
Skid Steer Loader
Tractor Loader
Loader < 40 hp
Eq. Used On
4,000 / 1,814
4,000 / 1,814
4,000 / 1,814
2,000 / 907
Capacity (lbs./kg)
Welded Steel
Welded Steel
Welded Steel
Welded Steel
Frame Construction
“Universal” Skid Steer
“Universal Skid Steer
Std. Pin-type*
Std. Pin-type*
Mounting
6” to 40”
6” to 40”
6” to 50”
6” to 45”
Fork Spacing
Notched Rail
Notched Rail
Notched Rail
H.D. Steel Rod
Fork Carrier
1-1/4” x 4” w/ Latch
1-1/4” x 4” w/ Latch
1-1/4” x 4” w/ Latch
1-1/4” x 3”
Forks
42”
48”
48”
46”
Usable Fork Length
345 / 157
359 / 163
460/ 209
352 / 160
Weight (lbs. / kg)
832400
832415
831830
830780
Item Number
John Deere Integrated Frame Pallet Forks
Clamp-On Bucket
JDPF-5442
JDPF-5448
JDPF-6748
Model
John Deere Front Loader John Deere Front Loader
John Deere Front Loader
Eq. Used On
4,000 / 1,814
4,000 / 1,814
5,500 / 2495
Capacity (lbs./kg)
Welded Steel
Welded Steel
Welded Steel
Frame Construction
400/500 Series JD
400/500 Series JD
600/700 Series JD
Mounting
6” to 40”
6” to 40”
6” to 40”
Fork Spacing
Notched Rail
Notched Rail
Notched Rail
Fork Carrier
1-1/4” x 4” w/ Latch
1-1/4” x 4” w/ Latch
1-1/2” x 4” w/ Latch
Forks
42 / 107
48 / 122
48 / 122
Fork Length (in/cm)
345 / 157
359 / 163
373 / 169
Weight (lbs. / kg)
832420
832435
832440
Item Number
Global (Euro Hook Style) Integrated Frame Pallet Forks
Clamp-On bucket
GLPF-442
GLPF-448
GLPF-5548
BF-1000, 2000, 4000
Model
Tractor Front Loader
Tractor Front Loader
Tractor Front Loader
Loader Buckets
Eq. Used On
4,000 / 1,814
4,000 / 1,814
5,500 / 2495
1,000-4,000 lbs.
Capacity (lbs./kg)
Welded Steel
Welded Steel
Welded Steel
Welded Steel
Frame Construction
READ AND UNDERSTAND OPERATOR'S
Global Carrier
Global Carrier
Global Carrier
Mounting
MANUAL BEFORE OPELoader
RATION.Bucket
6” to 40”
6” to 40”
6” to 40”
Adjustable
Fork Spacing
Notched Rail
Notched Rail
Notched Rail
N/A OR
Fork Carrier
NEVER ALLOW CHILDERN
BYSTAND
OUND SKIDSteel
STEER
1-1/4” x 4” w/ Latch
1-1/4” x 4” w/ Latch
1-1/2” x 4” w/
Latch ERS ARFabricated
Forks
WHEN YOU ARE35”,
USING
EQUIPMEN
42 / 107
48 / 122
48 / 122
42”,
& 42” T.
Fork Length (in/cm)
345 / 157
359 / 163
373 / 169
78 lb./ 102 lb./ 191 lb.
Weight (lbs. / kg)
832452
832458
832460
831950, 831930, 831960
Item Number
* Optional Interfacing Brackets Available
READ AND UNDERSTAND OPERATOR’S
MANUAL BEFORE OPERATION.
NEVER ALLOW CHILDERN OR BYSTANDERS AROUND SKID
STEER OR TRACTOR WHEN YOU ARE USING EQUIPMENT.
Worksaver Inc. has a corporate policy of continuous product improvement and development; therefore,
specifications are subject to change without any advance notice. Worksaver Inc. is not responsible for
differences between specifications or illustrations contained in this publication and the actual equipment.
Information Provided By:
Worksaver, Inc.
P.O. Box 100, Litchfield, IL 62056-0100
Phone: 217-324-5973 • Fax: 217-324-3356
E-mail: sales@worksaver.com
Web: www.worksaver.com
Worksaver
Designed.
Engineered.
Remarkable
Value.
Worksaver®
ETG Series Skid Steer Tine Grapple
•
•
•
Designed for use on skid steers
(and tractor front loaders) utilizing
the “Universal” skid steer attaching
system.
Ideal for raking, piling, and loading
brush and other hard to handle
materials while leaving dirt behind.
Unique upper grapple design
provides clamping force to hold
material securely.
• Greaseable pivot points on upper
grapple for long service life.
• Low profile design offers great
forward visibility for superior control
in close quarters and easy access to
skid steer seat.
• Shield plate on upper grapple
provides protection for hydraulic
cylinder.
ETG Tine Grapple Specifications
Model
Overall width (in/cm)
Overall depth (in/cm)
Inside depth (in/cm)
Overall height (in/cm)
Grapple opening (in/cm)
Upper grapple width (in/cm)
Number of tines
Tine spacing (in/cm)
Cylinder pressure rating (psi/bar)
Cylinder hoses / flat-faced couplers
Integral mounting system
Weight (lb/kg)
Horse power range
Product Item No.
ETG-5
61.5 / 156
35.5 / 90
28.5 / 72
25.5 / 65
34 / 86
34 / 86
7
10 / 25
2500 / 172
Standard
“Universal” Skid Steer
492 / 223
30 – 80 HP
811020
Be sure tractor / skid steer is properly counterbalanced.
Information Provided By:
Worksaver, Inc.
P.O. Box 100, Litchfield, IL 62056-0100
Phone: 217-324-5973 • Fax: 217-324-3356
E-mail: sales@worksaver.com
Web: www.worksaver.com
ETG-6
71.75 / 182
35.5 / 90
28.5 / 72
25.5 / 65
34 / 86
34 / 86
8
10 / 25
2500 / 172
Standard
“Universal” Skid Steer
520 / 236
30- 80- HP
811025
Worksaver.
Designed.
Engineered.
Remarkable
Value.
WORKSAVER®
Crane Boom for Skid Steer
Versatile tool design for the way you work. Ideal
for moving or loading hard to handle objects.
Worksaver
Boom Crane for Skid Steer
•
SKID STEER BOOM CRANE SPECIFICATIONS
Lift Capacity at farthest attaching point* (lb./kg)....................1700 / (771 kg)
Lift Capacity at middle attaching point* (lb./kg) ....................2000 / (907 kg)
Lift capacity at closest attaching point* (lb./kg) ......................2200 / (998 kg)
Overall boom length (in/mm) ...............................................78 / (1981 mm)
Boom construction ................................................................3” Square Steel Tubing
Mounting ..............................................................................“universal” Skid Steer
Quick-attach system
Shipping weight (lb./kg) .......................................................193 / (87.5 kg)
Product Computer Number ..................................................
*Dependent on lift capacity of the Skid Steer.
•
•
•
•
•
•
Designed for strength, durability and
reliability.
Ideal for lifting or moving objects on
the job site.
Features three lifting points for
increased flexibility in loading and
lifting.
All welded steel construction for long
life.
Boom utilizes 3” square tube stock
providing strength and durability.
Clevis and chain hook provided as
standard equipment.
Mounts on any Skid Steer with
“universal” attaching system.
READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE OPERATION.
Worksaver Inc. has a corporate policy of continuous product improvement and development;
therefore, specifications are subject to change without any advance notice. Worksaver Inc. is not
responsible for differences between specifications or illustrations contained in this publication and
the actual equipment.
Worksaver.
Designed.
Engineered.
Remarkable
Worksaver,
Inc.
Value.
P.O. Box
100, Litchfield, IL 62056-0100
Phone: 217-324-5973 • Fax: 217-324-3356
E-mail: sales@worksaver.com
Web: www.worksaver.com
Information Provided By:
Worksaver.
WORKSAVER ®
Designed.
Engineered.
Remarkable
Value.
ROTARY BROOMS
ROTARY BROOMS FOR SKID STEERS &
3-PT. TRACTOR MOUNT
• Top quality rotary brooms for use by contractors,
municipalities, institutions, and farmers.
• Remove dirt, sand, gravel and trash from construction
entrances, parking lots, bridges , driveways and sidewalks.
• Remove thatch and prepare turf for the growing season.
• Clean snow or leaves from streets, driveways, and building
entrances.
• Excellent for general clean up before sealing or repairing
pavement.
• Hydraulically driven skid steer
models in 5-ft., 6-ft., & 7-ft. widths
with 32” diameter brushes.
• Variable flow control valve for
optimum broom speed.
• Step-through mount design for
easy in/out of skid steer cab.
• Broom angles 30° right or left.
• Parking stands standard.
• PTO driven 3-pt. tractor mount in
5-ft., 6-ft., & 7-ft. widths with 32”
diameter brushes.
• Double gearbox drive for smooth
power transmission and easy
reversal of brush rotation.
• Broom angles 30° right or left.
• Parking stands standard.
Worksaver Rotary Brooms
Worksaver.
Designed.
Engineered.
Remarkable
Value
•
•
•
•
•
•
Hydraulically driven models for Skid Steers, PTO driven models for 3-pt. tractor mounts (Cat.I).
5-ft., 6-ft., and 7-ft. widths.
32 inch diameter convoluted brushes available in Poly (P) or both Poly and Wire (PW).
Brooms angle up to 30-degrees right or left. Manual or hydraulic angle adjustment kits available.
Height adjustment chains maintain an even operating position.
Parking stand included as standard equipment.
SKID STEER ROTARY BROOM SPECIFICATIONS
Variable flow control valve allows operator to adjust broom speed independently of engine or ground speed. 4.36 / 1 chain drive ratio
for excellent torque. Heavy-duty #60 drive chain for long life. Step-through mount design for easy in/out of skid steer cab.
Model
SSMB -325P SSMB -325PW
SSMB -326P SSMB -326-PW SSMB -327P SSMB -327PW
Overall Width (in/cm)
69 / 175
69 / 175
81 / 206
81 / 206
93 / 236
93 / 236
Brush Dia. (in/cm)
32 / 81
32 / 81
32 / 81
32 / 81
32 / 81
32 / 81
Sweeping Width (in/cm)
60 / 152
60 / 152
72 / 183
72 / 183
84 / 213
84 / 213
53 / 135
53 / 135
64 / 163
64 / 163
76 / 193
76 / 193
Width @ 30°Angle (in/cm)
Mounting System
Skid Steer
Skid Steer
Skid Steer
Skid Steer
Skid Steer
Skid Steer
Brush Material
Poly
Poly / Wire
Poly
Poly / Wire
Poly
Poly / Wire
Hyd. Motor Rating
16 GPM
16 GPM
16 GPM
16 GPM
16 GPM
16 GPM
Dirt Deflector
Optional
Optional
Optional
Optional
Optional
Optional
Sprinkler System
Optional
Optional
Optional
Optional
Optional
Optional
Weight (lb/kg)
640 / 290
640 / 290
740 / 336
740 / 336
840 / 381
840 / 381
Item #
610961
610960
610966
610965
610971
610970
3-pt. ROTARY BROOM SPECIFICATIONS
Double gearbox drive for smooth power transmission and low maintenance. Top “T-Shaft” gearbox allows easy reversal of brush
rotation. Designed for category I tractors with 1,000 lbs. or greater 3-pt. lift capacity.
Model
RMB-325P
RMB-325PW
RMB-326P
RMB-326PW
RMB-327P
RMB-327PW
Overall Width (in/cm)
69 / 175
69 / 175
81 / 206
81 / 206
93 / 236
93 / 236
Brush Diameter (in/cm)
32 / 81
32 / 81
32 / 81
32 / 81
32 / 81
32 / 81
Sweeping Width (in/cm)
60 / 152
60 / 152
72 / 183
72 / 183
84 / 213
84 / 213
53 / 135
53 / 135
64 / 163
64 / 163
76 / 193
76 / 193
Width @ 30°Angle (in/cm)
Mounting System
3-pt. (Cat. I)
3-pt. (Cat. I)
3-pt. (Cat. I)
3-pt. (Cat. I)
3-pt. (Cat. I)
3-pt. (Cat. I)
Brush Material
Poly
Poly / Wire
Poly
Poly / Wire
Poly
Poly / Wire
PTO RPM Range
540
540
540
540
540
540
Sprinkler System
Optional
Optional
Optional
Optional
Optional
Optional
Dirt Deflector
Optional
Optional
Optional
Optional
Optional
Optional
Weight (lb/kg)
640 / 290
640 / 290
740 / 336
840 / 381
740 / 336
840 / 381
Item #
610705
610700
610755
610750
610805
610800
Item #610702
Item #610703
Item #610940
Item #610950
Angle Adjustment Kits (all models require either a manual or hydraulic kit)
Manual Angle Adjustment Kit for either skid steers or tractor 3-pt.
3-pt. hydraulic Angle Adjustment Kit – includes cylinder & hoses less tips.
Skid steer hydraulic Angle Adjustment Kit – includes elec. hydraulic solenoid control valve. For skid
steer brooms used on units with only one set of remotes. Includes cylinder, hoses, valve, & flat-faced
couplers. Factory installed.
Electric Solenoid Kit (Optional)
Field installed electric hydraulic solenoid valve kit – fits #610703 hydraulic angle kit above.
Information Provided By:
Worksaver, Inc.
P.O. Box 100, Litchfield, IL 62056-0100
Phone: 217-324-5973 • Fax: 217-324-3356
E-mail: sales@worksaver.com
Web: www.worksaver.com
Worksaver.
Designed.
Engineered.
Remarkable
Value.
WORKSAVER®
Model SS-585 Mixer
Skid Steer Mixer. Ideal for all mixing jobs.
Worksaver
Model SS-585 Mixer
•
•
All welded steel drum construction
with internal paddles for uniform
mixing and clean dumping.
Compact, trouble free, long life design
with few moving parts.
MODEL SS-585 MIXER SPECIFICATIONS
Capacity ...............................................................................Five (5) cu./ft. (1 bag mix)
Drum opening (in/mm) .........................................................20 (508)
Overall drum length (in/mm) ................................................32 (813)
Diameter of drum (in/mm) ...................................................30 (762)
Drum construction ................................................................Welded Steel
Drive system ..........................................................................Hydraulic
Hydraulic requirements..........................................................8 GPM (min)
Drum drive ...........................................................................#50 roller chain
Drive ratio .............................................................................6.4:1
Shield drum drive ..................................................................Standard
Bearing type ..........................................................................Bronze Oilite (greaseable)
Hydraulic motor ...................................................................Standard
Mounting...............................................................................“Universal style” skid steer
Parking stands ........................................................................Standard
Shipping weight (lb./kg) ........................................................436 (198)
Product Computer Number ..................................................780900
•
•
•
•
•
•
•
•
Ideal for all mixing jobs. Five (5) cu./ft.
capacity (1 bag mix).
Hydraulic motor drive for easy
operation and low maintenance
requirements..
Parking stands for easy storage.
Number 50-roller chain drives
mixing drum.
Bronze Oilite (greaseable) bearings
provides long bearing life.
Direct mount all welded frame fits
“universal style” skid steer attachment
system
Flow control valve allows easy control
of speed of mixer.
Simple lever control for engagement /
disengagement of mixing drum.
READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE OPERATION.
Worksaver Inc. has a corporate policy of continuous product improvement and development;
therefore, specifications are subject to change without any advance notice. Worksaver Inc. is not
responsible for differences between specifications or illustrations contained in this publication and
the actual equipment.
Worksaver.
Designed.
Engineered.
Remarkable
Worksaver,
Inc.
Value.
P.O. Box
100, Litchfield, IL 62056-0100
Phone: 217-324-5973 • Fax: 217-324-3356
E-mail: sales@worksaver.com
Web: www.worksaver.com
Information Provided By:
NEWS
WORKSAVER, Inc.
9 Worksaver Trail
P.O. Box 100
Litchfield, Illinois 62056
(217) 324-5973 Fax (217) 324-3356
Date: January 16, 2015
Web: http://www.worksaver.com
E-Mail: sales@worksaver.com
Contact: Sales Dept.
SARG – Sweep Action Rock Grapple
Handling rocks and so much more – the Sweep Action Rock Grapple (SARG) from
Worksaver is revolutionizing the way rock grapples work. With its patent pending design
the SARG allows the operator to own one tool to sort large or small rocks / debris,
resulting in low cost of ownership.
The front grapple operates in a
sweeping action to pull rocks or
debris into the unit making site
clean-up effortless.
Grapple design retains the rocks or
debris, allowing the operator to rock
the attachment to sift dirt out of the
material.
Models feature hoses routed through
the main frame to provide hose
protection. Hoses are positioned
down the left-hand back of the
bucket resulting in maximum dump
and roll back as optimum hose
length is maintained. Hose routing can be changed to the right-hand side for JCB models
of skid steer loaders.
Rocks, brush, logs, stumps, debris or scrap, the SARG handles them all.
Rocks
Rocks are no problem for the
SARG. Grapples work
independently of each other
allowing the SARG to clamp
loads that are uneven in nature.
Logs
Move logs of varying sizes when
clearing land. Bolt-on side plates
can be removed revealing cutouts
to help handle logs and stumps.
Quality Built with Innovation
Sweep Action
The SARG with its 66 degrees of
sweep allows the operator to
move rocks of varying sizes into
the bucket. The front sweep
clamp will remain in the “open”
position until the rear section is
closed. Once closed, the front
sweep clamp operates like a
thumb moving material into and
retaining it in the bucket.
Available: March 2015
Model
Item #
SARG-72
812120
SARG-84
812160
Description
Sweep Action Rock Grapple for
Skid Steer loaders.
72”-overall width. Front grapple
operates in a sweeping action to
pull rocks or debris into the unit.
Shipped with hoses and flat face
connect under pressure couplers
Sweep Action Rock Grapple for
Skid Steer loaders.
84”-overall width. Front grapple
operates in a sweeping action to
pull rocks or debris into the unit.
Shipped with hoses and flat face
connect under pressure couplers
Weight
List
1194 lbs.
$5,695.00
1375 lbs.
$6,095.00
Quality Built with Innovation
Effective 5-1-2015
Material Handling Attachments
Designed for Use on Skid Steer Loaders
These products are manufactured to interface with the “Universal “skid steer quick attach mounting.
Product
Model
Item #
Description
Lbs.
List
Low-Profile Tine Grapple for 30-80 hp
skid steers & tractor front loaders w/
“Universal” skid steer attaching system.
470
2,025.00
61” wide w/ single upper grapple. 7
811020
ETG-5
tines spaced 10”. Includes hyd hoses,
“connect under pressure” flat-faced
couplers.
Low-Profile Tine Grapple for 30-80 hp
skid steers & tractor front loaders w/
811025
“Universal”
skid steer attaching system.
498
2,140.00
ETG-6
Same as ETG-5 above, but 72” wide, 8
tines spaced 10”.
Low-Profile Tine Grapple with Dual
Upper Grapples for 30-80 hp. skid steers
811090
& tractor front loaders w/”Universal”
570
2,295.00
ETG-26
skid steer attaching system. 72” wide
with 8-lower tines space 10” Includes
hyd. hoses and “connect under pressure”
flat-face couplers
Skid Steer Split Top Grapple Rake. Unit
is 62” wide with two upper grapples, for
820
3,420.00
SSGR-262 811435 handling a variety of materials. Unit is
equipped with two 2” x10” hyd.
cylinders.
Skid Steer Split Top Grapple Rake. Unit
is 77” wide with two upper grapples, for
811440
handling a variety of materials. Unit is
965
3,870.00
SSGR-277
equipped with two 2” x10” hyd.
cylinders.
Grapple Parking Stand Kit. Fits all
811395
grapples except Low Profile models.
26
175.00
Parking
Allows upright storage and easy hook
Stand Kit
up on hard surfaces.
Skid Steer Tree Crane Boom. Ideal for
811140 moving trees for transplanting. Booms’
SSTBoverall length is 59.25-inches.Rated at
182
675.00
3500
3,500 lbs.
Page 1 of 9
Effective 5-1-2015
Material Handling Attachments
Designed for Use on Skid Steer Loaders
These products are manufactured to interface with the “Universal “ skid steer quick attach mounting.
Hoses are routed through the tube for increased protection.
Product
Model
Item #
Description
Lbs.
List
Heavy Duty Skid Steer Low Profile
Scrap Bucket. Cylinder guards protect
cylinders and components. 72” overall
791
3,560.00
LPSB-72 811780 width. Cutting edge is drilled to accept a
replaceable beveled cutting edge.
Complete with “connect under pressure”
flat-faced couplers
Heavy Duty Skid Steer Low Profile
Scrap Bucket. Same as above,
823
3,715.00
LPSB-78 811820
but with 78” overall width.
Heavy Duty Skid Steer Low Profile
Scrap Bucket. Same as above,
855
4,000.00
LPSB-84 811860
but with 84” overall width.
Bolt-on end plate kit for HD Scrap
End Plate Kit
811795 Buckets. 21” long, 19” high, to enclose
99.00
ends, bolts and nuts included
Bolt-on
beveled cutting edge for LPSBOptional
811790
72. Reversible – protects/strengthens
115
395.00
Bolt-on
original edge. ¾”x8”x72”.
Cutting
Pre-drilled w/ hardware
Edge
Bolt-on beveled cutting edge for LPSBOptional
811830
78. Reversible – protects/strengthens
125
425.00
Bolt-on
original edge. ¾”x8”x78”.
Cutting
Pre-drilled w/ hardware
Edge
Bolt-on beveled cutting edge for LPSBOptional
811870
84. Reversible – protects/strengthens
135
455.00
Bolt-on
original edge. ¾”x8”x84”.
Cutting
Pre-drilled w/ hardware
Edge
Heavy Duty Skid Steer Low Profile
Tine Grapple. Cylinder guards protect
LPTG-72
811750 cylinders and components. 72” overall
820
3,530.00
width. Tines spaced 5 ½”. Complete
with “connect under pressure”
flat-faced couplers
Heavy Duty Skid Steer Low Profile
864
3,665.00
LPTG-78 811800 Tine Grapple. Same as above, but with
78” overall width
Heavy Duty Skid Steer Low Profile
896
3,785.00
LPTG-84 811840 Tine Grapple. Same as above, but with
84” overall width.
Page 2 of 9
Effective 5-1-2015
Sweep Action Grapples
SARG (Sweep Action Rock Grapple) for Use on Skid Steer Loaders
The “SARG” features upper grapples with 66-degrees of sweep allowing the operator to move rocks of varying
sizes into the tine bucket. The sweep clamp operates like a thumb moving material into and retaining it in the
bucket. Hydraulic hoses are routed through the frame for added protection of components. Bolt-on side plates hold
smaller rocks in the bucket. Hoses are routed through the tube for increased protection.
Product
Model
Item #
SARG-72
812120
SARG-84
812160
Description
“SARG” Sweep Action Rock
Grapple. 72” width with 1.25”
round tines spaced 2.5” apart
Patent Pending upper
Sweep Action Grapples.
Complete with “connect under
pressure” flat-faced couplers.
“SARG” Sweep Action Rock
Grapple. 84” width with 1.25”
round tines spaced 2.5” apart
Patent Pending upper
Sweep Action Grapples.
Complete with “connect under
pressure” flat-face couplers.
Lbs.
List
1194
5,695.00
1344
6,095.00
SAMB (Sweep Action Material Bucket) for Use On Skid Steer Loaders
The Sweep Action Material Bucket features a sold bottom bucket with standard bolt on cutting edge. Upper
grapples feature 66-degree of sweep allowing the operator to mover debris of varying sizes into the bucket.
Hydraulic hoses are routed through the frame for added protection of components. Bolt-on side plates hold smaller
debris in the bucket.
SAMB-72
812180
SAMB-84
812190
72” Sweep Action Material
Bucket with solid bottom.
Bolt-on beveled cutting edge is
standard. Patent Pending upper
Sweep Action Grapples.
Complete with “connect under
pressure flat-face couplers.
84” Sweep Action Material
Bucket with solid bottom.
Bolt-on beveled cutting edge is
standard. Patent Pending upper
Sweep Action Grapples.
Complete with “connect under
pressure flat-face couplers.
Page 3 of 9
1075
5,725.00
1210
6,165.00
Effective 5-1-2015
Material Handling Attachments
Manure / Silage / Debris Forks Designed for Use on
Skid Steer Loaders / Tractor Loaders
These products (S-models) are manufactured to interface with the “Universal “ skid steer quick attach system.
Product
Model
Item #
M/S-60S
812305
M/S-66S
812400
M/S-72S
812315
M/SG-60S
812310
M/SG-72S
812320
Description
Manure / Silage Fork, 60-inches
in width. Units features
8-forged cranked tines spaced 7inches apart. Integrated mount to
interface with “universal” skid
steer mounting system.
Manure / Silage Fork, 66-inches
in width. Units features
9-forged cranked tines spaced 7inches apart. Integrated mount to
interface with “universal” skid
steer mounting system.
Manure / Silage Fork, 72-inches
in width. Units features
10-forged cranked tines spaced 7inches apart. Integrated mount to
interface with “universal” skid
steer mounting system.
Manure / Silage Fork with upper
grapple, 60-inches in width. Unit
features 8-forged cranked tines
spaced 7-inches apart, 34-inch
wide upper grapples, hoses with
connect under pressure flat-faced
couplers and integrated mount to
interface with “universal” skid
steer mounting system
Manure / Silage Fork with upper
grapple, 72-inches in width. Unit
features 10-forged cranked tines
spaced 7-inches apart, 34-inch
wide upper grapples, hoses with
connect under pressure flat-faced
couplers and integrated mount to
interface with “universal” skid
steer mounting system
Page 4 of 9
Lbs.
List
225
990.00
240
1,030.00
270
1,070.00
375
2,325.00
450
2,535.00
Effective 5-1-2015
Material Handling Attachments
Pallet Forks Designed for Use on Skid Steer Loaders
Interfaces with the “Universal “ skid steer quick attach mount. Check if unit was built before 1995.
Product
Model
Item #
Description
Lbs
List
Skid Steer Pallet Forks with step-through
995.00
832400 backstop. Rated at 4,000 lbs. Rail style, 42” 356
SSPF-442
x 1-1/4” x 4” solid forks w/ spring-loaded
toggle latch for positioning.
Skid Steer Pallet Forks with step-through
832415 backstop. Rated at 4,000 lbs. Rail style, 48” 370
995.00
SSPF-448
x 1-1/4” x 4” solid forks w/ spring-loaded
toggle latch for positioning.
832495
Skid Steer Pallet Forks step-through
410 1,100.00
SSPF-5548
backstop Rated at 5,500 lbs. Rail style
831370
Skid Steer Pallet forks with One-piece
315
995.00
SSPF-3748
backstop Rated 4,000 lbs.
Misc. Forks Replacements sold in pairs
831369
Pair of 42” Replacement Forks (Rail
175
489.00
Mount) rated 4,000 lbs. for SSPF-3742,
SSPF-442, JDPF-442
831379
Pair of 48” Replacement Forks (Rail
196
499.00
Mount) rated 4,000 lbs. for SSPF-3748,
SSPF-448, JDPF-5448, PF-448
832475
Pair of 48” Replacement Forks rated at
226
529.00
5,500 lbs. for GLPF-5448, SSPF-5548
Page 5 of 9
Effective 5-1-2015
Mini Skid Steer / Compact Tool Carrier Attachments
Mini Skid Steer Pallet Forks
MPF-900
832670
MPF-2000
832640
MPF2000 B/G
832695
SBMS-50
SBMS-50 B/G
MGU-48
MGB/G-48
Designed for Mini Skid Steers / Compact
Tool Carries, features forks that are
1”x3”x31.5” w/ universal mini mount
rated at 900 lbs.
Designed for Mini Skid Steers / Compact
Tool Carries, features forks that are
1.18”x3”x42” w/ universal mini mount
rated at 2,000 lbs.
Designed for Bobcat MT – series (MT-50,
MT-52, MT-55) & S-70 and Gehl 1640E
this unit features forks that are
1.18” x 3” x 42” rated at 2,000 lbs.
Mini Skid Steer Snow Blade
Designed for Mini Skid Steers / Compact
360245 Tool Carries, Moldboard is 50” wide with
dual trip springs, reversible cutting edge.
21” high moldboard
Designed for Bobcat MT – series (MT-50,
360260
MT-52, MT-55) & S-70 and Gehl 1640E
Moldboard is 50” wide with dual trip
springs, reversible cutting edge.
21” high moldboard
Mini Skid Steer Grapple
Grapple Designed for Mini Skid Steers /
Compact Tool Carries w/ universal mini
811730
mount. Single upper grapple 31” wide,
Includes hoses & couplers
Overall unit width is 48”
Grapple Designed for Bobcat MT – series
(MT-50, MT-52, MT-55) & S-70 and
811740 Gehl 1640E Single upper grapple 31” wide,
Includes hoses & couplers
Overall unit width is 48”
Page 7 of 9
150
595.00
215
685.00
225
705.00
280
1,730.00
285
1,780.00
290
1,690.00
310
1,730.00
Effective 5-1-2015
Land Management Attachments
Designed for use on Skid Steer Loaders
SS-590
Skid Steer Mixer. 5 Cu. Ft. (1 bag
mix). Hydraulic driven mixer with
parking stands. Internally welded
780950
mixing paddles for proper mixing.
Includes flow control valve (on/off)
for easy operation. Hoses includes
flat-faced couplers.
Flat-Faced Coupler Set interfaces w/
2505650 standard ends on our SS attachments.
1 ea. ½” male 1 ea. ½” female coupler
Page 6 of 9
395
3,650.00
3
175.00
Effective 5-1-2015
Skid Steer Grader Blade
Designed for Use on Skid Steer Loaders
This products is manufactured to interface with the “Universal “ skid steer quick attach mount. Unit
can be used with a Leica Laser system. Required Opt. Junction box (2507020) and
Leica components (ordered from Leica) shown on page.
Product
Model
Item #
Description
Lbs.
List
The patented Grader, designed to
be used by asphalt, landscaping and
10,250.00
SSGB-8B 811940 concrete flatwork contractors. Unit 1195
features 8-ft., six-way hydraulically
controlled (proportional current
valve) moldboard operated by an
in-cab remote. (Requires opt.
Junction Box 2507020 to interface
with Leica Laser system.)
Optional Laser Interface Junction
2507020 Box Kit. This allows the SSGB-8B
3
699.00
to interface with a Leica laser
system which is purchased from
Leica (see page 70)
\
End Plates
811980
Optional end plates for SSGB-8B
sold in pairs.
295.00
Laser Poles
812110
Optional Laser Poles for SSGB-8B
sold in pairs
160.00
Note: All Weights shown are an estimated weight and do not include shipping materials.
Page 8 of 9
Effective 5-1-2015
Leica Laser Components for use with Worksaver SSGB-8B Skid Steer Grader Blade.
The below listed Leica Laser components can be purchased through a Leica distributor / dealer. To locate
the nearest Leica distributor / dealer contact Leica Geosystems, Inc. at
800-367-9453 or www.leica-geosystems.us
The following Leica items will need to be purchased through a Leica distributor / dealer to allow the
SSGB-8B when equipped with (2507020) Laser Junction Box to be controlled by a laser.
Leica Part No.
6005465
6007520
764910
767437
764866
777657
761509
798790-1.0.0en
819460-1.1.0en
8241565
Description
Kit – Laser Receiver, MLS700
Kit – 2D Panel, iCON grad
MMB1300 Cradle for 2D/3D Panel
MJB1300 Junction Box, 2 sensor ports
Cable for cradle 5Pin M12 / open, 5M
Snap Hook, stainless steel, 8mm x 80mm (5/16”)
MMB1330 RAM Bracket, Size C (1.5”)
Leica iCONgrade iCP32 user manual
Leica iCON grade iGDx Installation Manual
Decal – Powered by Leica
Page 9 of 9
Quantity Required
2
1
1
1
1
2
1
1
1
2
Download PDF