Ricoh | LDD735 | Service manual | Ricoh LDD735 Service manual

CÓPIA NÃO CONTROLADA
Need Machine Image for Cover
C274
SERVICE MANUAL
00xxxxMIU
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
C274
SERVICE MANUAL
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
C274
SERVICE MANUAL
00xxxxMIU
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
It is the reader's responsibility when discussing the information contained
within this document to maintain a level of confidentiality that is in the best
interest of Ricoh Americas Corporation and its member companies.
NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY
FASHION AND DISTRIBUTED WITHOUT THE PRIOR
PERMISSION OF RICOH AMERICAS CORPORATION.
All product names, domain names or product illustrations, including
desktop images, used in this document are trademarks, registered
trademarks or the property of their respective companies.
They are used throughout this book in an informational or editorial fashion
only and for the benefit of such companies. No such use, or the use of
any trade name, or web site is intended to convey endorsement or other
affiliation with Ricoh products.
© 2009 RICOH Americas Corporation. All rights reserved.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
WARNING
The Service Manual contains information
regarding service techniques, procedures,
processes and spare parts of office equipment
distributed by Ricoh Americas Corporation.
Users of this manual should be either service
trained or certified by successfully completing a
Ricoh Technical Training Program.
Untrained and uncertified users utilizing
information contained in this service manual to
repair or modify Ricoh equipment risk personal
injury, damage to property or loss of warranty
protection.
Ricoh Americas Corporation
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
LEGEND
PRODUCT
CODE
C274-77
C274-92
GESTETNER
DX 2330
DX 2430
COMPANY
LANIER
RICOH
LDD745
DX 2330
LDD735
DX 2430
SAVIN
N/A
N/A
DOCUMENTATION HISTORY
REV. NO.
*
DATE
5/2009
COMMENTS
Original Printing
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
C274
TABLE OF CONTENTS
1. PRODUCT INFORMATION.......................................................... 1-1
1.1 SPECIFICATIONS ..................................................................................... 1-1
1.2 MECHANISM OVERVIEW ......................................................................... 1-2
1.2.1 COMPONENT LAYOUT ................................................................... 1-2
1.2.2 ELECTRICAL COMPONENT LAYOUT ............................................ 1-3
1.2.3 DRIVE LAYOUT................................................................................ 1-7
1.3 GUIDANCE FOR THOSE WHO ARE FAMILIAR WITH PREDECESSOR
PRODUCTS..................................................................................................... 1-8
2. INSTALLATION ........................................................................... 2-1
2.1 INSTALLATION REQUIREMENTS............................................................ 2-1
2.1.1 OPTIMUM ENVIRONMENTAL CONDITION .................................... 2-1
2.1.2 ENVIRONMENTS TO AVOID ........................................................... 2-1
2.1.3 POWER CONNECTION ................................................................... 2-1
2.1.4 MACHINE ACCESS.......................................................................... 2-1
Dimensions........................................................................................... 2-2
2.2 INSTALLATION PROCEDURE.................................................................. 2-3
2.2.1 MAIN UNIT........................................................................................ 2-3
Accessory Check.................................................................................. 2-3
Installation Procedure........................................................................... 2-4
2.3 OPTIONAL INSTALLATION .................................................................... 2-12
2.3.1 ADDITIONAL DRUMS .................................................................... 2-12
2.3.2 PRINTER UNIT VC-20 AND INTERFACE BOARD TYPE 20 ......... 2-13
Accessory Check (Interface Board Type 20) ...................................... 2-13
Accessory Check (Printer Unit VC-20) ............................................... 2-13
Installation Procedure......................................................................... 2-14
3. PREVENTIVE MAINTENANCE ................................................... 3-1
3.1 MAINTENANCE TABLES .......................................................................... 3-1
4. REPLACEMENT AND ADJUSTMENT ........................................ 4-1
4.1 GENERAL CAUTION................................................................................. 4-1
SM
i
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
4.2 SPECIAL TOOLS....................................................................................... 4-2
4.3 IMAGE ADJUSTMENT .............................................................................. 4-3
4.3.1 SP6-42: IMAGE ADJUSTMENT PATTERN PRINT .......................... 4-3
4.3.2 DIP SWITCHES ................................................................................ 4-4
Overview .............................................................................................. 4-4
4.3.3 DIPSW103 NO.5 TO 8 – MASTER FEEDING SPEED
ADJUSTMENT ........................................................................................... 4-5
4.3.4 DIPSW101 NO.1 TO 4 – PAPER REGISTRATION POSITION
ADJUSTMENT ........................................................................................... 4-6
4.3.5 DIPSW101 NO.5 TO 8 – MASTER WRITING POSITION
ADJUSTMENT ........................................................................................... 4-7
4.3.6 DIPSW102 NO.1 TO 3 – THERMAL HEAD ENERGY CONTROL ... 4-9
4.3.7 DIPSW103 NO.1 TO 4 – SCANNING SPEED ADJUSTMENT ......... 4-9
4.4 COVERS AND BOARDS ......................................................................... 4-11
4.4.1 FRONT COVER, OPERATION PANEL .......................................... 4-11
4.4.2 REAR COVER ................................................................................ 4-11
4.4.3 MPU ................................................................................................ 4-12
4.4.4 PSU ................................................................................................ 4-13
4.5 SCANNER ............................................................................................... 4-14
4.5.1 COVERS......................................................................................... 4-14
4.5.2 1ST AND 2ND FEED ROLLERS, CIS (CONTACT IMAGE
SENSOR)................................................................................................. 4-14
4.5.3 DOCUMENT SENSOR ................................................................... 4-15
4.5.4 SCANNER MOTOR ........................................................................ 4-16
4.6 MASTER FEED........................................................................................ 4-17
4.6.1 MASTER MAKING UNIT................................................................. 4-17
4.6.2 THERMAL HEAD............................................................................ 4-17
Installation .......................................................................................... 4-18
4.6.3 THERMAL HEAD VOLTAGE ADJUSTMENT ................................. 4-19
4.6.4 MASTER END SENSOR ADJUSTMENT ....................................... 4-20
4.7 MASTER EJECT...................................................................................... 4-21
4.7.1 MASTER EJECT UNIT ................................................................... 4-21
4.7.2 MASTER EJECT ROLLERS ........................................................... 4-21
4.8 PAPER FEED .......................................................................................... 4-22
4.8.1 PAPER FEED ROLLER / FRICTION PAD...................................... 4-22
4.8.2 PAPER FEED PRESSURE ADJUSTMENT.................................... 4-22
C274
ii
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
4.8.3 PAPER SEPARATION PRESSURE ADJUSTMENT ...................... 4-23
4.9 PRINTING ................................................................................................ 4-26
4.9.1 PRESS ROLLER ............................................................................ 4-26
4.9.2 PAPER REGISTRATION ROLLER................................................. 4-27
4.9.3 PRESS ROLLER RELEASE LEVER ADJUSTMENT ..................... 4-28
4.9.4 PRINTING PRESSURE ADJUSTMENT ......................................... 4-29
4.10 DRUM ................................................................................................ 4-31
4.10.1 PREPARATION......................................................................... 4-31
4.10.2 CLOTH SCREEN ...................................................................... 4-31
Installation .......................................................................................... 4-32
4.10.3 CLAMPER / METAL SCREEN .................................................. 4-34
Installation .......................................................................................... 4-35
4.10.4 INK PUMP UNIT........................................................................ 4-36
4.10.5 INK ROLLER UNIT / INK ROLLER ONE WAY CLUTCH .......... 4-36
4.10.6 DOCTOR ROLLER GAP ADJUSTMENT .................................. 4-37
4.10.7 INK DETECTION ADJUSTMENT.............................................. 4-39
4.11 PAPER DELIVERY ............................................................................ 4-40
4.11.1 PAPER DELIVERY UNIT .......................................................... 4-40
4.11.2 DELIVERY BELT / PAPER EXIT SENSOR............................... 4-41
4.11.3 EXIT PAWL ADJUSTMENT ...................................................... 4-41
Timing Adjustment.............................................................................. 4-42
4.12 MAIN DRIVE ...................................................................................... 4-45
4.12.1 MAIN DRIVE TIMING BELT ADJUSTMENT ............................. 4-45
4.12.2 MAIN MOTOR PULLEY POSITION .......................................... 4-45
4.13 FIRMWARE UPDATE ........................................................................ 4-47
5. SYSTEM MAINTENANCE REFERENCE .................................... 5-1
5.1 SERVICE PROGRAM MODE .................................................................... 5-1
5.1.1 SP TABLES ...................................................................................... 5-1
5.1.2 USING SERVICE PROGRAM MODES ............................................ 5-1
Entering SP Mode ................................................................................ 5-1
Leaving SP Mode ................................................................................. 5-1
5.1.3 USING THE SP MODE ..................................................................... 5-1
6. TROUBLESHOOTING ................................................................. 6-1
6.1 SERVICE CALL CONDITIONS .................................................................. 6-1
6.2 ELECTRICAL COMPONENT DEFECTS ................................................... 6-2
SM
iii
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
6.3 FUSE, LED, VR, DIP-SW, AND TP TABLES............................................. 6-3
C274
iv
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Read This First
Important Safety Notices
Responsibilities of the Customer Engineer
Customer Engineer
Maintenance shall be done only by trained customer engineers who have completed
service training for the machine and all optional devices designed for use with the machine.
Reference Material for Maintenance
ƒ
Maintenance shall be done using the special tools and procedures prescribed for
maintenance of the machine described in the reference materials (service manuals,
technical bulletins, operating instructions, and safety guidelines for customer
engineers).
ƒ
In regard to other safety issues not described in this document, all customer engineers
shall strictly obey procedures and recommendations described the "CE Safety Guide".
ƒ
Use only consumable supplies and replacement parts designed for use of the
machine.
Before Installation, Maintenance
Shipping and Moving the Machine
ƒ
Work carefully when lifting or moving the machine. If the machine is heavy,
two or more customer engineers may be required to prevent injuries (muscle
strains, spinal injuries, etc.) or damage to the machine if it is dropped or tipped
over.
ƒ
Personnel moving or working around the machine should always wear proper
clothing and footwear. Never wear loose fitting clothing or accessories
(neckties, loose sweaters, bracelets, etc.) or casual footwear (slippers,
sandals, etc.) when lifting or moving the machine.
ƒ
Always unplug the power cord from the power source before you move the
product. Before you move the product, arrange the power cord so it will not fall
under the product.
Power
ƒ
Always disconnect the power plug before doing any maintenance procedure.
After switching off the machine, power is still supplied to the main machine
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
and other devices. To prevent electrical shock, switch the machine off, wait for
a few seconds, then unplug the machine from the power source.
ƒ
Before you do any checks or adjustments after turning the machine off, work
carefully to avoid injury. After removing covers or opening the machine to do
checks or adjustments, never touch electrical components or moving parts
(gears, timing belts, etc.).
ƒ
After turning the machine on with any cover removed, keep your hands away
from electrical components and moving parts. Never touch the cover of the
fusing unit, gears, timing belts, etc.
Installation, Disassembly, and Adjustments
ƒ
After installation, maintenance, or adjustment, always check the operation of
the machine to make sure that it is operating normally. This ensures that all
shipping materials, protective materials, wires and tags, metal brackets, etc.,
removed for installation, have been removed and that no tools remain inside
the machine. This also ensures that all release interlock switches have been
restored to normal operation.
ƒ
Never use your fingers to check moving parts causing spurious noise. Never
use your fingers to lubricate moving parts while the machine is operating.
Special Tools
ƒ
Use only standard tools approved for machine maintenance.
ƒ
For special adjustments, use only the special tools and lubricants described in
the service manual. Using tools incorrectly, or using tools that could damage
parts, could damage the machine or cause injuries.
During Maintenance
General
ƒ
Before you begin a maintenance procedure: 1) Switch the machine off, 2)
Disconnect the power plug from the power source.
Safety Devices
ƒ
Never remove any safety device unless it requires replacement. Always
replace safety devices immediately.
ƒ
Never do any procedure that defeats the function of any safety device.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Modification or removal of a safety device (fuse, switch, etc.) could lead to a
fire and personal injury. Always test the operation of the machine to ensure
that it is operating normally and safely after removal and replacement of any
safety device.
ƒ
For replacements use only the correct fuses or circuit breakers rated for use
with the machine. Using replacement devices not designed for use with the
machine could lead to a fire and personal injuries.
Organic Cleaners
ƒ
During preventive maintenance, never use any organic cleaners (alcohol, etc.)
other than those described in the service manual.
ƒ
Make sure the room is well ventilated before using any organic cleaner. Use
organic solvents in small amounts to avoid breathing the fumes and becoming
nauseous.
ƒ
Switch the machine off, unplug it, and allow it to cool before doing preventive
maintenance. To avoid fire or explosion, never use an organic cleaner near
any part that generates heat.
ƒ
Wash your hands thoroughly after cleaning parts with an organic cleaner to
contamination of food, drinks, etc. which could cause illness.
ƒ
Clean the floor completely after accidental spillage of silicone oil or other
materials to prevent slippery surfaces that could cause accidents leading to
hand or leg injuries. Use "My Ace" Silicone Oil Remover (or dry rags) to soak
up spills. For more details, please refer to Technical Bulletin "Silicone Oil
Removal" (A024-50).
Power Plug and Power Cord
ƒ
Before serving the machine (especially when responding to a service call),
always make sure that the power plug has been inserted completely into the
power source. A partially inserted plug could lead to heat generation (due to a
power surge caused by high resistance) and cause a fire or other problems.
ƒ
Always check the power plug and make sure that it is free of dust and lint.
Clean it if necessary. A dirty plug can generate heat which could cause a fire.
ƒ
Inspect the length of the power cord for cuts or other damage. Replace the
power cord if necessary. A frayed or otherwise damaged power cord can
cause a short circuit which could lead to a fire or personal injury from electrical
shock.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
ƒ
Check the length of the power cord between the machine and power supply.
Make sure the power cord is not coiled or wrapped around any object such as
a table leg. Coiling the power cord can cause excessive heat to build up and
could cause a fire.
ƒ
Make sure that the area around the power source is free of obstacles so the
power cord can be removed quickly in case of an emergency.
ƒ
Make sure that the power cord is grounded (earthed) at the power source with
the ground wire on the plug.
ƒ
Connect the power cord directly into the power source. Never use an
extension cord.
ƒ
When you disconnect the power plug from the power source, always pull on
the plug, not the cable.
After Installation, Servicing
Points to Confirm with Operators
At the end of installation or a service call, instruct the user about use of the machine.
Emphasize the following points.
ƒ
Show operators how to remove jammed paper and troubleshoot other minor problems
by following the procedures described in the operating instructions.
ƒ
Point out the parts inside the machine that they should never touch or attempt to
remove.
ƒ
Confirm that operators know how to store and dispose of consumables.
ƒ
Make sure that all operators have access to an operating instruction manual for the
machine.
ƒ
Confirm that operators have read and understand all the safety instructions described
in the operating instructions.
ƒ
Demonstrate how to turn off the power and disconnect the power plug (by pulling the
plug, not the cord) if any of the following events occur: 1) something has spilled into the
product, 2) service or repair of the product is necessary, 3) the product cover has been
damaged.
ƒ
Caution operators about removing paper fasteners around the machine. They should
never allow paper clips, staples, or any other small metallic objects to fall into the
machine.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Safety Instructions for this Machine
Prevention of Physical Injury
1.
Before disassembling or assembling parts of the machine and peripherals, make sure
that the machine and peripheral power cords are unplugged.
2.
The plug should be near the machine and easily accessible.
3.
If any adjustment or operation check has to be made with exterior covers off or open
while the main switch is turned on, keep hands away from electrified or mechanically
driven components.
4.
The inside and the metal parts of the fusing unit become extremely hot while the
machine is operating. Be careful to avoid touching those components with your bare
hands.
5.
To prevent a fire or explosion, keep the machine away from flammable liquids, gases,
and aerosols.
Health Safety Conditions
1.
If you get ink in your eyes by accident, try to remove it with eye drops or flush with
water as first aid. If unsuccessful, get medical attention.
2.
If you ingest ink by accident, induce vomiting by sticking a finger down your throat or
by giving soapy or strong salty water to drink.
Observance of Electrical Safety Standards
1.
The machine and its peripherals must be installed and maintained by a customer
service representative who has completed the training course on those models.
Safety and Ecological Notes for Disposal
1.
Dispose of replaced parts in accordance with local regulations.
2.
Used ink and masters should be disposed of in an environmentally safe manner and in
accordance with local regulations.
Symbols
This manual uses several symbols. The meanings of those symbols are as follows:
See or Refer to
Core tech manual
Clip ring
E-ring
Screw
Connector
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
PREVENTIVE MAINTENANCE
APPENDIX: SERVICE CALL CONDITION
REPLACEMENT AND ADJUSTMENT
APPENDIX: ELECTRICAL COMPONENT DEFECTS
SYSTEM MAINTENANCE REFERENCE
APPENDIX: SP MODE TABLES
TAB
POSITION 2
TAB
POSITION 8
TAB
POSITION 7
TROUBLESHOOTING
TAB
POSITION 3
APPENDIX: MAINTENANCE TABLES
TAB
POSITION 4
INSTALLATION
TAB
POSITION 5
APPENDIX: SPECIFICATIONS
TAB
POSITION 6
PRODUCT INFORMATION
TAB
POSITION 1
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
PRODUCT INFORMATION
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Product
Information
Specifications
1. PRODUCT INFORMATION
1.1 SPECIFICATIONS
See "Appendices" for the following information:
ƒ
SM
General specifications
1-1
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Mechanism Overview
1.2 MECHANISM OVERVIEW
1.2.1 COMPONENT LAYOUT
1. Tension roller
12. Exit pawl
2. Master feed roller
13. Transport belts
3. Platen roller
14. Vacuum fan motor
4. Thermal head
15. Paper delivery table
5. Master roll
16. Air knife fan motor
6. Paper feed roller
17. Master eject rollers
7. Paper table
18. Master eject box
8. Registration rollers
19. 2nd feed roller
9. Doctor roller
20. CIS (Contact Image Sensor)
10. Ink roller
21. 1st feed rollers
11. Press roller
C274
1-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Product
Information
Mechanism Overview
1.2.2 ELECTRICAL COMPONENT LAYOUT
SM
1-3
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Mechanism Overview
Boards
No.
13
34
37
Component
Function
Operation Panel Board
This board controls the operation panel.
Main Processing Unit
Controls all machine functions, both directly and
(MPU)
through other boards.
Power Supply Unit (PSU)
Provides dc power to the machine.
Motors
No.
Component
Function
2
Scanner Motor
Drives the scanner.
4
Ink Pump Motor
Drives the ink pump.
5
Master Feed Motor
Feeds the master to the drum.
11
Cutter Motor
Cuts the master.
22
Master Eject Motor
used masters into the master eject box.
23
Air Knife Fan Motor
26
Vacuum Fan Motor
27
Pressure Plate Motor
Drives the pressure plate.
29
Clamper Motor
Opens or closes the master clamper on the drum.
31
Main Motor
33
Registration Motor
C274
Rotates the fan to provide air to separate the leading
edge of the paper from the drum.
Provides suction so that paper is held firmly on the
transport belt.
Rotates the drum, paper feed roller and transport
belts.
Feeds the paper to align it with the master on the
drum.
1-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Product
Information
Mechanism Overview
Switches
No.
7
14
Component
Function
Right Side Cover Set
Switch
Door Safety Switch
Checks if the right side cover is closed.
Checks whether the front door is properly closed.
Solenoids
No.
12
30
Component
Function
Front Pressure Release
Releases the press roller to apply printing pressure.
Solenoid
Rear Pressure Release
Releases the press roller to apply printing pressure.
Solenoid
Counters
No.
Component
Function
20
Master Counter
Keeps track of the total number of masters made.
21
Paper Counter
Keeps track of the total number of copies.
Sensors
No.
Function
3
Cutter HP Sensor
Detects when the cutter is at the home position.
8
Master Set Cover Sensor
Checks if the master set cover is properly set.
Master End Sensor
Detects when the master making unit runs out of
9
SM
Component
master roll.
1-5
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Mechanism Overview
No.
10
Component
Function
Registration Sensor
Detects paper approaching the registration roller.
Document Sensor
Detects the leading edge of the original to determine
15
when to turn off the scanner motor. Checks for
original misfeeds.
16
Pressure Plate HP Sensor Detects when the pressure plate is at the home
position.
Pressure Plate Limit
Detects when the pressure plate is in the lowest
Sensor
position.
18
Master Eject Sensor
Detects used master misfeeds.
19
Drum Master Sensor
Detects if there is a master on the drum.
24
Eject Box Set Sensor
Checks if the master eject box is installed.
25
Paper Exit Sensor
Detects paper misfeeds at the exit.
28
Clamper Open Sensor
Detects if the clamper is in the open position.
32
Feed Start Timing Sensor
Determines the paper feed start timing.
36
Clamper Closed Sensor
Detects if the clamper is in the closed position.
MasterEject Position
Detects when the drum is at the master eject
(Drum HP) Sensor
position.
17
38
Others
No.
1
6
35
C274
Component
Function
Contact Image Sensor
This sensor reads and converts the light reflected
(CIS)
from the document into an analog video signal.
Thermal Head
Burns the image onto the master.
Paper Feed Clutch
Transmits main motor drive to the paper feed rollers
at the appropriate time.
1-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Product
Information
Mechanism Overview
1.2.3 DRIVE LAYOUT
1.
Master eject motor
2.
Scanner motor
3.
Pressure plate motor
4.
Clamper motor
5.
Main motor
6.
Registration motor
7.
Master feed motor
SM
1-7
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Guidance for Those Who are Familiar with Predecessor Products
1.3 GUIDANCE FOR THOSE WHO ARE FAMILIAR
WITH PREDECESSOR PRODUCTS
Machine C274 is a successor model to Machine C261. If you have experience with the
predecessor products, the following information will be of help when you read this manual.
Different Points from Predecessor Products
C274
Drum pump adjustment
ƒ
C274
No *1
C261
Yes
*1 This model uses the trochoid pump unit that is used in the C267 series.
1-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
INSTALLATION
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Installation Requirements
2. INSTALLATION
Carefully select the installation location because environmental conditions greatly affect
machine performance.
2.1.1 OPTIMUM ENVIRONMENTAL CONDITION
1.
Temperature: 10 to 30 °C (50 to 86 °F)
2.
Humidity: 20 to 90 %RH
3.
Install the machine on a strong and level base. The machine must be level within 5mm
(0.2") both front to rear left to right.
2.1.2 ENVIRONMENTS TO AVOID
1.
Locations exposed to direct sunlight or strong light (more than 1,500 lux).
2.
Dusty areas
3.
Areas containing corrosive gases.
4.
Locations directly exposed to cool air from an air conditioner or reflected heat from a
space heater. (Sudden temperature changes from low to high or vice versa may cause
condensation within the machine.)
2.1.3 POWER CONNECTION
1.
Securely connect the power cord to a power source.
2.
Make sure that the wall outlet is near the machine and easily accessible.
3.
Make sure the plug is firmly inserted in the outlet.
4.
Avoid multi-wiring
5.
Do not pinch the power cord.
2.1.4 MACHINE ACCESS
Place the machine near a power source, providing minimum clearance as shown below.
SM
2-1
CÓPIA NÃO CONTROLADA
C274
Installation
2.1 INSTALLATION REQUIREMENTS
CÓPIA NÃO CONTROLADA
Installation Requirements
Dimensions
C274
2-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Installation Procedure
2.2 INSTALLATION PROCEDURE
2.2.1 MAIN UNIT
Installation
Accessory Check
Make sure that you have all the accessories listed below.
Description
Q'ty
1. Master Spool
2
2. Paper Feed Side Pad
2
3. Operating Instructions
1
4. NECR (Ricoh version only)
1 set
5. Model Name Plate (C274-77)
1 set
6. Paper Table
1 set
7. Paper Delivery Table
1 set
8. Easy Operation Guide
1
9. Safety Information (C274-93 and C274-94 only)
1
10. Bundled Items List (C274-76 and C274-78 only)
1
SM
2-3
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Installation Procedure
Installation Procedure
ƒ
To avoid serious injury, do not connect the power plug to the machine until you are
instructed to do so.
1.
Unpack the machine and remove all the wrapping.
2.
Remove all filament tape and string securing the covers and units as shown above.
C274
2-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Installation
Installation Procedure
3.
Remove the front tape [A], the tag [B], and the rear tape [C].
ƒ
To remove the rear tape, pull the portion shown in the diagram toward the
front of the machine.These tapes were also used in the Titanium2 (C261).
4.
Open the right side cover, and take out the accessory bag [D].
5.
Insert both spools into a new master roll.
SM
2-5
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Installation Procedure
6.
Install the master roll.
7.
Open the master making unit cover, and insert the leading edge of the master roll
under the platen roller. The arrows [E] indicate the correct position of the master
leading edge.
ƒ
The leading edge of the master does not enter the interior of the master
making unit, because the part at the arrows [E] is convex.
C274
2-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Installation
Installation Procedure
8.
Close the master making unit cover [F] using both hands until it clicks into place.
9.
Close the right side cover.
10. Open the front door.
11. Release the ink holder lock lever [G] and pull out the ink holder [H].
12. Insert a new ink cartridge.
SM
2-7
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Installation Procedure
13. Take the paper table and paper delivery table out of the box.
14. Lower the paper feed tray adjustment lever [I], and install the paper table.( x 2)
ƒ
When installing the paper table, make sure that the hooks [J] are set firmly.
ƒ
Two side fence friction pads are included as accessories. They are not used
normally, but if paper multi-feed frequently occurs or thin paper is used, the
side fence friction pads can be installed to apply stopping pressure to the
paper.
C274
2-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Installation
Installation Procedure
15. Attach the side and end fences, as shown. ( x 3)
16. Install the paper delivery table. ( x 2)
17. Release the paper feed side plate lock levers [K] and adjust the side plates to match
the paper size.
SM
2-9
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Installation Procedure
18. Load paper into the paper table.
19. Shift the paper feed tray adjustment lever [I] up to the paper feeding position.
20. Adjust the side and end fences of the paper delivery table to match the paper size.
21. Attach the original table [L].
C274
2-10
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Installation Procedure
22. Firmly insert the power plug in the outlet.
23. Turn on the main switch.
24. Press the clear/stop key while holding down the 0 key, to supply ink to the drum.
Installation
25. Make some test copies.
SM
2-11
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Optional Installation
2.3 OPTIONAL INSTALLATION
2.3.1 ADDITIONAL DRUMS
There are two types of drum units:
B4 size Color Drum: Color Drum Type 20 (M)
LG size Color Drum: Color Drum Type 20 (S)
1.
Remove the protective sheet [A] from the drum unit.
2.
Attach a color indicator decal to the drum case. The decal must be the same color as
the ink in use.
3.
Remove the drum unit.
4.
Leave the master wrapped around the removed drum to protect the drum from dust
C274
2-12
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Optional Installation
5.
Keep the removed drum unit in the drum case.
6.
Install the drum unit.
7.
Remove the ink cartridge cap.
8.
Insert the ink cartridge in the ink holder.
2.3.2 PRINTER UNIT VC-20 AND INTERFACE BOARD TYPE 20
ƒ
The Interface board type 20 must be installed before you install the Printer Unit
VC-20.
Accessory Check (Interface Board Type 20)
Check the quantity and condition of the accessories in the box against the following list:
Description
Q'ty
1. Interface Board
1
2. Interface Cable
1
3. Bracket
2
4. Screw M3x6
6
Accessory Check (Printer Unit VC-20)
Check the quantity and condition of the accessories in the box against the following list:
SM
2-13
CÓPIA NÃO CONTROLADA
C274
Installation
and from drying.
CÓPIA NÃO CONTROLADA
Optional Installation
Description
Q'ty
1. Printer Controller Board
1
2. Screws
3
3. Installation CD
1
4. Quick Install Guide
1
5. Safety Information
1
Installation Procedure
ƒ
To avoid serious injury, do not connect the power plug to the machine until you are
instructed to do so.
Remove the rear cover ( Replacement and Adjustment – Covers / Boards - Rear Cover)
1.
Remove the bracket [A] (x1).
ƒ
C274
You do not need this bracket and its screws any more.
2-14
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Installation
Optional Installation
1.
Attach the printer controller board [E] to the bracket [B] (x4).
2.
Attach the bracket [C] to the bracket [B] (x2).
3.
Connect the connector [D] to the socket on the right side of the board [E].
ƒ
4.
Make sure that the connector is securely connected to the socket.
Attach the bracket assembly [F] to the same place that the bracket [A] (Step 1) was
installed (1 screw).
SM
2-15
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Optional Installation
ƒ
In this step, only use the M3x6 screw included with the Interface board Type
20.
5.
Connect the socket [J] on the interface board to CN108 [K] on the MPU [L].
ƒ
Make sure that the socket is securely connected to CN108.
6.
Connect the connector [H] to the socket [G] on the interface board.
7.
Attach the interface board [I] to the bracket assembly [F] (x 2).
8.
Connect the connector [O] to CN102 on the MPU [N].
ƒ
9.
Make sure that the connector is securely connected to CN102.
Clamp the harness to the five places shown (#1-5) around the MPU (=x5).
ƒ
C274
Do not connect the connector [M] anywhere. Leave it unconnected.
2-16
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PREVENTIVE MAINTENANCE
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Maintenance Tables
3. PREVENTIVE MAINTENANCE
3.1 MAINTENANCE TABLES
See "Appendices" for the following information:
Maintenance table
Preventive
Maintenance
ƒ
SM
3-1
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
REPLACEMENT AND ADJUSTMENT
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
General Caution
4. REPLACEMENT AND ADJUSTMENT
4.1 GENERAL CAUTION
ƒ
Turn off the main power switch and unplug the machine before attempting any of
the procedures in this section.
This manual uses several symbols. The meaning of those symbols are as follows:
ƒ
This manual uses several symbols. The meaning of those symbols are as follows:
ƒ
: See or refer to, : screw, : connector, : E-ring, : clip, =: clamp
Replacement
and
Adjustment
ƒ
SM
4-1
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Special Tools
4.2 SPECIAL TOOLS
The following are the special tools used for service.
Part Number
A0699502
C274
Description
Alvania 2 Grease
Q’ty
1
4-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Image Adjustment
4.3 IMAGE ADJUSTMENT
Adjusts the image position on prints by changing the DIP switch settings.
Adjust the following in the given order.
DIPSW103 No.5 to 8 – Master Feeding Speed Adjustment
DIPSW101 No.1 to 4 – Paper Registration Position Adjustment
DIPSW101 No.5 to 8 – Master Writing Position Adjustment
DIPSW102 No.1 to 3 – Thermal Head Energy Control
DIPSW103 No.1 to 4 – Scanning Speed Adjustment
When correcting errors made when printing with the controller, use only the first two steps.
When correcting errors made when printing with scanned originals, do all adjustments in
the given order.
This test pattern is used for master feeding speed adjustment.
ƒ
Master Feeding Speed Adjustment: ( DIPSW103 No.5 to 8 – Master Feeding Speed
Adjustment)
This test pattern is generated in the MPU, and does not use the scanner unit. So, this
pattern can also be used to determine whether an image problem is caused by the scanner
or the thermal head.
If there is an image problem during copying but the test print is OK, the problem could be in
the scanner unit.
The print paper should be B4 or LG size when using this test pattern.
SM
4-3
CÓPIA NÃO CONTROLADA
C274
Replacement
and
Adjustment
4.3.1 SP6-42: IMAGE ADJUSTMENT PATTERN PRINT
CÓPIA NÃO CONTROLADA
Image Adjustment
4.3.2 DIP SWITCHES
Overview
DIPSW
No.
Bit No.
Name
Settings
Paper Registration Position
( DIPSW101 No.1 to 4 – Paper
Adjust
Registration Position Adjustment)
Master Writing Position
( DIPSW101 No.5 to 8 – Master
Adjust
Writing Position Adjustment)
Thermal Head Energy
( DIPSW102 No.1 to 3 – Thermal
Control
Head Energy Control)
4
Not used
-
5
Drum Size Selection
6
Size in Metric or Inch
7
Panel Beeper
8
Not used
1 to 4
101
5 to 8
1 to 3
ON: LG
OFF: B4
102
103
C274
1 to 4
ON: inch
OFF: mm
ON: Enabled
OFF: Disabled (Default)
-
Scanning Speed Adjustment
4-4
( DIPSW103 No.1 to 4 – Scanning
Speed Adjustment)
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Image Adjustment
DIPSW
No.
Bit No.
Name
5 to 8
Settings
Master Feeding Speed
( DIPSW103 No.5 to 8 – Master
Adjustment
Feeding Speed Adjustment)
4.3.3 DIPSW103 NO.5 TO 8 – MASTER FEEDING SPEED
ADJUSTMENT
Purpose: To adjust the sub-scan magnification for the master by changing the speed of the
master feed motor.
Inputting a positive value stretches the image on the master. Inputting a negative value
shrinks it.
1.
Access SP6-42 (Image Adjustment Pattern Print), and then press the master making
key. ( SP6-42: Image Adjustment Pattern Print)
2.
Exit the SP mode, print 5 copies at 90 cpm (speed "Fast"). Use the 5th print for the
adjustment.
3.
The black area should be 300 ± 0.5 mm in length.
4.
If it is out of the standard, then adjust DIPSW103-5 to 103-8. {(300 – Value) / 300} x
100 = ± X.X %
DIPSW103-5
DIPSW103-6
DIPSW103-7
DIPSW103-8
difference
ON
ON
ON
ON
+1.4%
OFF
ON
ON
ON
+1.2%
ON
OFF
ON
ON
+1.0%
OFF
OFF
ON
ON
+0.8%
ON
ON
OFF
ON
+0.6%
OFF
ON
OFF
ON
+0.4%
ON
OFF
OFF
ON
+0.2%
OFF
OFF
OFF
ON
0
SM
4-5
CÓPIA NÃO CONTROLADA
C274
Replacement
and
Adjustment
Adjust standard: 300 ± 0.5 mm
CÓPIA NÃO CONTROLADA
Image Adjustment
DIPSW103-5
DIPSW103-6
DIPSW103-7
DIPSW103-8
difference
OFF
OFF
OFF
OFF
0
ON
ON
ON
OFF
-1.4%
OFF
ON
ON
OFF
-1.2%
ON
OFF
ON
OFF
-1.0%
OFF
OFF
ON
OFF
-0.8%
ON
ON
OFF
OFF
-0.6%
OFF
ON
OFF
OFF
-0.4%
ON
OFF
OFF
OFF
-0.2%
4.3.4 DIPSW101 NO.1 TO 4 – PAPER REGISTRATION
POSITION ADJUSTMENT
Purpose: To match the printing leading edge on the print paper with that on the original.
Adjustment standard: ±1.0 mm
The print position moves as shown below.
ƒ
The image position on a trial print, which is automatically made after making a
master, tends to vary. Do not use the trial print when making adjustments.
C274
4-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
DIPSW101-1 DIPSW101-2 DIPSW101-3 DIPSW101-4
Difference
Difference
ON
ON
ON
ON
+7 pulse
+3.563 mm
OFF
ON
ON
ON
+6 pulse
+3.054 mm
ON
OFF
ON
ON
+5 pulse
+2.545 mm
OFF
OFF
ON
ON
+4 pulse
+2.036 mm
ON
ON
OFF
ON
+3 pulse
+1.527 mm
OFF
ON
OFF
ON
+2 pulse
+1.018 mm
ON
OFF
OFF
ON
+1 pulse
+0.509 mm
OFF
OFF
OFF
ON
0
0
OFF
OFF
OFF
OFF
0
0
ON
ON
ON
OFF
-7 pulse
-3.563 mm
OFF
ON
ON
OFF
-6 pulse
-3.054 mm
ON
OFF
ON
OFF
-5 pulse
-2.545 mm
OFF
OFF
ON
OFF
-4 pulse
-2.036 mm
ON
ON
OFF
OFF
-3 pulse
-1.527 mm
OFF
ON
OFF
OFF
-2 pulse
-1.018 mm
ON
OFF
OFF
OFF
-1 pulse
-0.509 mm
1 pulse = 0.509 mm
4.3.5 DIPSW101 NO.5 TO 8 – MASTER WRITING POSITION
ADJUSTMENT
Purpose: To match the printing side-to-side on the print paper with that on the original.
Adjustment standard: ±1.0 mm
The master writing position moves as shown below.
SM
4-7
CÓPIA NÃO CONTROLADA
C274
Replacement
and
Adjustment
Image Adjustment
CÓPIA NÃO CONTROLADA
Image Adjustment
ƒ
The image position on a trial print, which is automatically made after making a
master, tends to vary. Do not use the trial print when making adjustments.
DIPSW101-5 DIPSW101-6 DIPSW101-7 DIPSW101-8
C274
Difference
Difference
ON
ON
ON
ON
-14dot
-1.185mm
OFF
ON
ON
ON
-12dot
-1.016mm
ON
OFF
ON
ON
-10dot
-0.847mm
OFF
OFF
ON
ON
-8dot
-0.677mm
ON
ON
OFF
ON
-6dot
-0.508mm
OFF
ON
OFF
ON
-4dot
-0.339mm
ON
OFF
OFF
ON
-2dot
-0.169mm
OFF
OFF
OFF
ON
0
0
OFF
OFF
OFF
OFF
0
0
ON
ON
ON
OFF
+14dot
+1.185mm
OFF
ON
ON
OFF
+12dot
+1.016mm
ON
OFF
ON
OFF
+10dot
+0.847mm
OFF
OFF
ON
OFF
+8dot
+0.677mm
4-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Image Adjustment
DIPSW101-5 DIPSW101-6 DIPSW101-7 DIPSW101-8
Difference
Difference
ON
ON
OFF
OFF
+6dot
+0.508mm
OFF
ON
OFF
OFF
+4dot
+0.339mm
ON
OFF
OFF
OFF
+2dot
+0.169mm
1 dot = 0.085 mm
4.3.6 DIPSW102 NO.1 TO 3 – THERMAL HEAD ENERGY
CONTROL
The default is -7%. This means that during printing mode, the thermal head energy is 93 %
of the maximum power.
Replacement
and
Adjustment
This can help to increase or decrease the image density. However, do not use this SP
under normal circumstances.
DIPSW102-1
DIPSW102-2
DIPSW102-3
Settings
OFF
OFF
OFF
-7% (Standard)
OFF
ON
OFF
-5%
OFF
OFF
ON
-3%
OFF
ON
ON
0
ON
OFF
OFF
-10%
ON
ON
OFF
-15%
ON
OFF
ON
-20%
4.3.7 DIPSW103 NO.1 TO 4 – SCANNING SPEED ADJUSTMENT
Purpose: To adjust the sub-scan magnification for scanning by changing the speed of the
scanner motor.
Inputting a positive value stretches the image on the master. Inputting a negative value
shrinks it.
Adjustment standard: Within 100 ± 0.5 %
SM
4-9
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Image Adjustment
1.
Make a copy at 90 cpm (speed "Fast")
2.
Compare the image on the print with that on the original.
3.
Make sure that the difference of the sub-scan magnification is within the standard.
4.
If it is out of standard, then adjust DIPSW103-1 to 103-4.
ƒ
The image position on a trial print, which is automatically made after making a
master, tends to vary. Do not use the trial print when making adjustments.
DIPSW103-1
DIPSW103-2
DIPSW103-3
DIPSW103-4
Difference
ON
ON
ON
ON
+1.4%
OFF
ON
ON
ON
+1.2%
ON
OFF
ON
ON
+1.0%
OFF
OFF
ON
ON
+0.8%
ON
ON
OFF
ON
+0.6%
OFF
ON
OFF
ON
+0.4%
ON
OFF
OFF
ON
+0.2%
OFF
OFF
OFF
ON
0
OFF
OFF
OFF
OFF
0
ON
ON
ON
OFF
-1.4%
OFF
ON
ON
OFF
-1.2%
ON
OFF
ON
OFF
-1.0%
OFF
OFF
ON
OFF
-0.8%
ON
ON
OFF
OFF
-0.6%
ON
OFF
OFF
OFF
-0.4%
OFF
ON
OFF
OFF
-0.2%
C274
4-10
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Covers and Boards
4.4 COVERS AND BOARDS
Replacement
and
Adjustment
4.4.1 FRONT COVER, OPERATION PANEL
[A]: Panel (x 4, x 2)
[B]: Front cover (x 6)
[C]: Front door (x 4)
4.4.2 REAR COVER
[A]: Rear cover (x 5)
SM
4-11
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Covers and Boards
4.4.3 MPU
ƒ
Remove the rear cover ( Rear Cover)
[A]: MPU (x 8, x 8)
ƒ
Check the dip switch settings on the old MPU and make the dip switch settings [B]
the same on the new MPU.
ƒ
Adjust the master end sensor after installing the new MPU. ( Master Feed Master End Sensor Adjustment)
ƒ
Adjust the ink detection after installing the new MPU. ( Drum - Ink Detection
Adjustment)
ƒ
C274
Ensure that the EPROM on the MPU contains the correct firmware.
4-12
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Covers and Boards
ƒ
Replacement
and
Adjustment
4.4.4 PSU
Remove the rear cover (Covers / Boards - Rear Cover)
[A]: PSU (x 6, x 3)
ƒ
When the PSU is replaced, the thermal head voltage returns to the default. Adjust
the thermal head voltage after installing the new board. ( Master Feed - Thermal
Head Voltage Adjustment)
SM
4-13
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Scanner
4.5 SCANNER
4.5.1 COVERS
[A]: Right side cover ( x 1)
[B]: Scanner cover ( x 4)
4.5.2 1ST AND 2ND FEED ROLLERS, CIS (CONTACT IMAGE
SENSOR)
C274
4-14
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Replacement
and
Adjustment
Scanner
[A]: Upper cover (x 4)
[B]: Guide plate (x 2)
[C]: CIS (x 1)
[D]: 1st feed roller (x 3)
[E]: 2nd feed roller (x 3)
4.5.3 DOCUMENT SENSOR
[A]: Upper guide plate ( x 2)
[B]: Document sensor ( x 1)
SM
4-15
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Scanner
4.5.4 SCANNER MOTOR
[A]: Scanner unit ( x 5, x 3)
[B]: Scanner motor ( x 2)
C274
4-16
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Master Feed
4.6 MASTER FEED
Replacement
and
Adjustment
4.6.1 MASTER MAKING UNIT
[A]: Master making unit ( x 2, x 5)
4.6.2 THERMAL HEAD
ƒ
Master making unit ( Master Making Unit)
[A]: Open the platen roller unit.
[B]: Thermal head upper cover ( x 2)
SM
4-17
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Master Feed
[C]: Thermal head side cover ( x 1)
ƒ
Close the platen roller unit.
[D]: Thermal head ( x 2)
Installation
If the following remarks are not followed, the thermal head will be installed incorrectly.
1.
Fit the base’s springs [A] over the protrusions [B] on the underside of the thermal head
(5 points).
2.
While fitting the tops of the springs [A] over the protrusions on the underside of the
thermal head, hook the lock pawls [C] of the thermal head onto the base (3 lock pawls).
Make sure to set the front side (the paper table side) first.
3.
Make sure that all protrusions are properly fitted into the springs.
ƒ
Adjust the thermal head voltage after installing the new thermal head. (
Thermal Head Voltage Adjustment)
C274
4-18
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Master Feed
ƒ
Don’t touch the surface with bare hands. (If you touch it, clean the surface with
alcohol.)
ƒ
Don’t touch the terminals of the connectors with bare hands.
4.6.3 THERMAL HEAD VOLTAGE ADJUSTMENT
ƒ
This adjustment is always required when the thermal head or PSU has been
replaced.
Purpose: To maintain master making quality and extend the lifetime of the thermal head.
Standard: Refer to the voltage value (X) printed on the thermal head. The value varies
from one thermal head to another.
The adjustment voltage should be between X and X - 0.1 V.
Tools: Circuit tester
Remove the rear cover ( Covers / Boards - Rear Cover)
ƒ
Read the voltage value on the decal on the thermal head.
1.
Connect the positive terminal of a circuit tester to TP701 and the negative terminal to
Replacement
and
Adjustment
ƒ
TP702 on the PSU.
ƒ
If the output and ground terminals touch each other, the board will be
damaged.
2.
Connect the power plug, and turn on the main switch to access SP mode.
3.
Select SP2-41 (Thermal head signal output).
4.
Press the # key. Power is continuously supplied to the thermal head, which could
damage the thermal head, so press the clear/stop key if you cannot finish the
adjustment quickly.
SM
4-19
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Master Feed
5.
Measure the voltage, and turn VR1 on the PSU until the value is between “+0” and
“-0.1” volts from the value on the thermal head decal.
4.6.4 MASTER END SENSOR ADJUSTMENT
Purpose: To ensure that the sensor detects the end mark (a solid black area) on the
master roll.
Standard: 2.0 ± 0.1 volts
Tools: The core of a used master roll (the core just before a master end display appears)
ƒ
Remove the rear cover ( Covers / Boards - Rear Cover)
1.
Place the core inside the master making unit, and close the master making cover.
2.
Connect the power plug, and turn on the main switch.
3.
Access SP6-41
4.
Turn VR102 [A] on the MPU board until the display is 2.0 ± 0.1 volts.
C274
4-20
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Master Feed
Master Eject
Replacement
and
Adjustment
4.6.5 MASTER EJECT UNIT
[A]: Paper delivery cover ( x 5)
[B]: Master eject box
[C]: Master eject unit ( x 2, x 3)
4.6.6 MASTER EJECT ROLLERS
ƒ
Master eject unit ( Master Eject Unit)
ƒ
[A]: Gears ( x 1)
[B]: Lower master eject roller ( x 2)
[C]: Upper master eject roller ( x 2, spring)
SM
4-21
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Paper Feed
4.7 PAPER FEED
4.7.1 PAPER FEED ROLLER / FRICTION PAD
[A]: Paper feed roller unit ( x 1)
[B]: Paper guide
[C]: Paper feed roller ( x 1)
[D]: Friction pad
4.7.2 PAPER FEED PRESSURE ADJUSTMENT
The position of the spring can be changed in order to change the amount of pressure
exerted by the paper tray adjustment plate.
This adjustment can be done:
ƒ
When feeding special paper (especially thick paper and thin paper)
ƒ
When the customer is experiencing feed problems.
C274
4-22
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
ƒ
Replacement
and
Adjustment
Paper Feed
Front cover ( Covers / Boards – Front Cover, Operation Panel)
Increase the feed pressure: [A]
Decrease the feed pressure: [E]
[B]
[F]
[C]
[G]
[D]
[H]
Default position: [A] and [E] positions
4.7.3 PAPER SEPARATION PRESSURE ADJUSTMENT
The position of the screw can be changed in order to change the amount of pressure
exerted by the friction pad.
This adjustment can be done:
ƒ
When feeding special paper, especially thick paper
ƒ
When the customer is experiencing feed problems.
SM
4-23
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Paper Feed
ƒ
Remove the paper table
ƒ
Move the separation pressure slider [A] to position 1 (right end).
Increase the paper separation pressure: Move up the screws [B]
Decrease the paper separation pressure: Move down the screws [B]
Default position: lowest position
Adjustment Procedure
C274
4-24
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Paper Feed
[C]: Standard position (35 to 81.5 g/m2, 9.3 to 21.6 lb.)
ƒ
The user can change the feed roller pressure by changing the position of the pressure
adjustment lever [C].
ƒ
If paper feed jams frequently occur, the lever should be moved to adjust the pressure.
ƒ
If non-feed or multi-sheet feed problems still occur, the paper separation pressure can
also be adjusted using the separation pressure slider [A].
ƒ
The default position of the slider [A] is position 3.
ƒ
By loosening then moving the screws [B] up or down, the spring [E], which applies
pressure to the friction pad block [F], moves up or down.
ƒ
SM
The default position of the screw [B] is at the lowest position.
4-25
CÓPIA NÃO CONTROLADA
C274
Replacement
and
Adjustment
[D]: Thick paper position (81.6 to 127.9 g/m2, 21.7 to 34.0 lb.)
CÓPIA NÃO CONTROLADA
Printing
4.8 PRINTING
4.8.1 PRESS ROLLER
ƒ
Take care to avoid possible injury. If the printing pressure release arms disengage,
the press roller will be pulled upwards suddenly.
ƒ
Remove the drum
[A]: Press roller ( x 1)
The bearings on the rear and front differ. During installation, ensure that the bearing with
the stopper [B] is positioned towards the rear of the machine.
C274
4-26
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Printing
ƒ
Remove the paper table
ƒ
Front cover ( Cover / Boards - Front Cover, Operation Panel)
ƒ
Rear cover ( Cover / Boards - Rear Cover)
ƒ
MPU ( Cover / Boards - MPU)
Replacement
and
Adjustment
4.8.2 PAPER REGISTRATION ROLLER
[A]: Registration motor (spring, x 3, belt)
[B]: Gear
[C]: Bearing ( x 2)
[D]: Bearing ( x 2)
[E]: Slider bracket ( x 2)
SM
4-27
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Printing
[F]: Plate ( x 4)
[G]: Registration roller
4.8.3 PRESS ROLLER RELEASE LEVER ADJUSTMENT
Purpose: To maintain the correct clearance between the press roller arms and press roller
lock levers. This ensures that the press roller is correctly released and pressed against the
drum when the press roller release solenoid is energized.
Standard: 0.7 to 1.2 mm
C274
4-28
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Printing
ƒ
Front cover ( Cover / Boards - Front Cover, Operation Panel)
ƒ
Rear cover ( Cover / Boards - Rear Cover)
1.
Turn the drum manually until the drum master clamper on the drum moves into the
lowest position. (This is when the high points of the cams on the drum flanges meet
with the cam followers on both ends of the press roller.)
ƒ
To find out the correct position of the drum for the adjustment, look at the rear end
of the drum shaft. The recess on the drum drive gear meets the hole [A] in the
bracket when the drum is in the correct position.
2.
Using a thickness gauge, measure the clearance [B] between the press roller arm [C]
and the press roller lock lever [D] (rear side). It should be between 0.7 and 1.2 mm
3.
If it is not correct, adjust the position of the press roller lock lever after loosening the
two screws [E].
4.
Repeat steps 2 and 3 for the front side.
4.8.4 PRINTING PRESSURE ADJUSTMENT
Purpose: To make better print results without decreasing the run length.
Standard: Within 10 ± 0.5 mm
SM
4-29
CÓPIA NÃO CONTROLADA
C274
Replacement
and
Adjustment
Tools: Thickness gauge
CÓPIA NÃO CONTROLADA
Printing
ƒ
Paper delivery unit ( Paper Delivery – Paper Delivery Unit)
1.
Adjust the distance [A] to 10 ± 0.5 mm by turning the adjusting bolt [B].
2.
Repeat the same procedure for the printing pressure spring at the non-operation side.
C274
4-30
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Drum
4.9 DRUM
4.9.1 PREPARATION
Before attempting any of the procedures in this section, wipe off the ink around the ink roller.
To do this, set SP3-6 (ink detection) to off, and feed paper until ink ends. The setting value
returns to the default value when power is switched off/on.
4.9.2 CLOTH SCREEN
Remove the drum
1.
Remove the drum upper bracket ( x 4).
2.
Release the stopper [A], then rotate the drum until the master clamper faces top.
3.
Remove the cloth screen [B] (x 4).
Replacement
and
Adjustment
ƒ
SM
4-31
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Drum
Installation
C274
4-32
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Replacement
and
Adjustment
Drum
ƒ
Do not scratch the cloth screen or metal screen.
ƒ
Properly insert the edge of the belt crossing [A] on the cloth screen under the mylar [B]
on the metal screen, as shown above.
Otherwise, ink will leak from the trailing edge of the master on the drum during a long
printing run.
ƒ
Make sure that the correct side of the screen is facing up. In addition, make sure that
the stays for securing the cloth screen are positioned correctly. (Refer to the upper
illustration.)
ƒ
When replacing the cloth screen, spread the screen around the metal screen while
strongly pulling the stay [C]. Adjust the stay so that it is parallel to the master clamper,
then tighten the screws.
ƒ
SM
Make sure that the cloth screen is not wrinkled while spreading it around the drum.
4-33
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Drum
4.9.3 CLAMPER / METAL SCREEN
ƒ
Remove the drum
ƒ
Cloth screen ( Cloth Screen)
[A]: Clamper lever (1 hexagon screw)
[B]: Clamper - open the clamping plate [C], then remove the clamper.
ƒ
Do not allow ink to get on the inside of the clamping plate [C]. Otherwise, the
master may slip off and the image position on the prints will move toward the
trailing edge of the prints during a printing run.
ƒ
Use a cloth dampened with water to clean the inside of the clamping plate [C].
Never use alcohol or other solvents, or the clamping force of the magnet will be
weakened.
[D]: Tape (do not lose it)
[E]: Metal screen ( x 12)
C274
4-34
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Drum
Replacement
and
Adjustment
Installation
ƒ
Make sure that the correct end of the metal screen is overlapping. (The right side
overlaps, as viewed from the non-operation side, as shown above.)
ƒ
Secure the metal screen with filament tape.
ƒ
The 4 screws holding the drum master clamper are longer than the 12 screws holding
the metal screen, although they are similar in appearance. Be careful not to mix them
up or use the wrong screws.
ƒ
When installing the metal screen, secure the trailing edge first with the 2 screws. Then,
tighten the other screws while removing the slack from the screen. Make sure that the
gap between the drum flanges and the screen is 0.3 mm or less, as shown above.
(The two holes [A] on the trailing side are round holes and the other holes are long
SM
4-35
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Drum
holes, to allow for the removal of the slack.)
ƒ
Position the springs [B] and [C] (one each at the front and rear) as shown when
reinstalling the drum master clamper [D].
ƒ
Do not scratch the cloth screen or metal screen.
4.9.4 INK PUMP UNIT
ƒ
Remove the drum
ƒ
Cloth screen ( Cloth Screen)
ƒ
Clamper / Metal screen ( Clamper / Metal Screen)
[A]: Ink pump unit ( x 1, x 2)
4.9.5 INK ROLLER UNIT / INK ROLLER ONE WAY CLUTCH
ƒ
Wipe off the ink around the ink roller beforehand (use SP3-6).
C274
4-36
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Drum
ƒ
Remove the drum
ƒ
Cloth screen ( Cloth Screen)
ƒ
Clamper / Metal screen ( Clamper / Metal Screen)
[A]: Connector cover ( x 2, x 2)
[B]: Ink socket ( x 1)
[C]: Front drum bracket ( x 3)
Replacement
and
Adjustment
[D]: Front drum flange
[E]: Drum rear plate ( x 2)
Untight the screw [F] to take off the drum rear stoppers ( x 1)
[G]: Drum rear flange
[H]: Ink roller unit
[I]: Ink roller one-way clutch
4.9.6 DOCTOR ROLLER GAP ADJUSTMENT
Purpose: To control the ink thickness around the ink roller.
Standard: A 0.07-mm gauge passes, but a 0.09-mm gauge does not.
Tools: Thickness gauge
SM
4-37
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Drum
ƒ
Normally the doctor roller gap is not adjusted or changed. It tends to be difficult to
change in the field. If the gap is too narrow, an uneven image may appear on the
prints. If it is too wide, too much ink will be applied to the drum screens, resulting in
ink leakage from the drum.
ƒ
Wipe off the ink around the ink roller beforehand. (Use SP3-6.)
ƒ
Remove the drum
ƒ
Remove the Ink roller unit
1.
Make sure that a 0.07 mm gap gauge goes through the gap [A] between the ink and
doctor rollers, and that a 0.09 mm gap gauge does not.
ƒ
The gap should be checked at both ends of the doctor roller. Insert a gap
gauge at each end of the roller. The gap tends to be larger for the center.
ƒ
While the gap gauge is inserted, hold the doctor and ink rollers with your
fingers in order to stop the rollers from rotating.
ƒ
2.
While the gap gauge is inserted, hold the end of the gap gauge.
If the gap is out of the standard, loosen the screw [B] and adjust the gap by turning the
cam bushing [C] for the front and for the rear.
ƒ
C274
Make sure to repeat the adjustment for both ends of the rollers.
4-38
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Drum
4.9.7 INK DETECTION ADJUSTMENT
Purpose: To ensure that the CPU detects a no ink condition.
ƒ
Before attempting this procedure, wipe off the ink around the ink roller. To do this,
set SP3-6 (Ink Detection) to OFF, and feed paper until ink ends. The setting value
returns to default value if the power is switched off/on.
Replacement
and
Adjustment
Standard: 4.0 ± 0.2μs
ƒ
Rear cover ( Covers / Boards – Rear Cover)
1.
Access SP6-40.
2.
Turn VR101 [A] on the MPU board until the display is “4.0 ± 0.2μ” (4.0 ± 0.2μs).
ƒ
SM
When the drum has ink inside, the machine displays “----“.
4-39
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Paper Delivery
4.10 PAPER DELIVERY
4.10.1 PAPER DELIVERY UNIT
ƒ
Rear cover ( Covers / Boards - Rear Cover)
[A]: Paper delivery cover ( x 5)
[B]: Paper delivery unit ( x 2, x 2, x 1)
C274
4-40
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Paper Delivery
Replacement
and
Adjustment
4.10.2 DELIVERY BELT / PAPER EXIT SENSOR
ƒ
Paper delivery unit ( Paper Delivery Unit)
[A]: Vacuum fan motor bracket ( x 4)
[B]: Delivery belts
[C]: Paper exit sensor ( x 1)
4.10.3 EXIT PAWL ADJUSTMENT
Purpose: To ensure that the exit pawls can move out of the way of the drum master
clamper while the drum is rotating.
Clearance adjustment
ƒ
You must set the drum to home position before you do this adjustment.
Standard: Within 1.15 ± 0.15 mm
ƒ
SM
Front cover (Covers / Boards - Front Cover, Operation Panel)
4-41
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Paper Delivery
ƒ
Rear cover (Covers / Boards - Rear Cover)
1.
Loosen screw [A] then screw [B] in this order (do not remove them). Make sure that the
bracket [C] becomes free from engagement and the cam follower [D] contacts the
drum flange.
2.
Using a gap gauge, measure the clearance [E] between the drum surface and the exit
pawls. It should be 1.15 ± 0.15 mm.
3.
If the clearance is not correct, adjust the clearance by turning the bolt [F].
4.
Reposition the bracket [C] and tighten the screws [A] and [B].
5.
Do the timing adjustment (see the next section).
Timing Adjustment
Standard: 0 or less than 0.5 mm
C274
4-42
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Replacement
and
Adjustment
Paper Delivery
ƒ
Front cover ( Covers / Boards - Front Cover, Operation Panel)
ƒ
Rear cover ( Covers / Boards - Rear Cover)
Do this after the clearance adjustment (the procedure is on the next page).
1.
Turn the drum manually until the recess in the drum drive gear meets the positioning
hole [A] in the bracket, as shown.
SM
4-43
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Paper Delivery
2.
Loosen screw [B] then screw [C] in that order (do not remove them). Make sure that
the bracket [D] becomes free from engagement and the cam follower [E] contacts the
drum flange.
3.
Measure the gap [F] between the cam follower and cam face (front drum flange). It
should be 0 to 0.5 mm.
4.
If the gap is not correct, loosen the two screws securing the cam follower bracket [G].
5.
Re-tighten the two screws while pushing the cam follower against the cam face. Make
sure that the gap [F] is 0 or less than 0.5 mm.
ƒ
6.
Do not push the cam followers too strongly against the cam.
Re-position the bracket [D] and tighten the screws [B] and [C].
C274
4-44
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Main Drive
4.11 MAIN DRIVE
4.11.1 MAIN DRIVE TIMING BELT ADJUSTMENT
Replacement
and
Adjustment
After the timing belt is replaced, correct belt tension must be applied.
ƒ
Rear cover ( Covers / Boards - Rear Cover)
ƒ
MPU ( Covers / Boards - MPU)
ƒ
PSU ( Covers / Boards - PSU)
1.
Loosen the screws [A], [B], and [C].
2.
Move the tension roller [D] to the right with a screwdriver [E] as shown.
3.
Tighten the screws [A], [B], and [C].
4.
Remove the screwdriver.
4.11.2 MAIN MOTOR PULLEY POSITION
After putting the pulley back on the main motor shaft, refer to the above illustration for the
correct position of the pulley.
SM
4-45
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Main Drive
C274
4-46
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Firmware Update
4.12 FIRMWARE UPDATE
1.
Before upgrading the firmware, check the current suffix version with SP3-1.
2.
Turn off the main switch and disconnect the power plug.
3.
Remove the rear cover.
4.
Replace the EPROM on the MPU.
5.
Connect the power plug and turn on the main switch.
6.
Access SP3-1 and confirm that the suffix version was changed.
SM
4-47
CÓPIA NÃO CONTROLADA
Replacement
and
Adjustment
The firmware in the EPROM on the MPU can be upgraded replacing the EPROM.
C274
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SYSTEM MAINTENANCE
REFERENCE
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Service Program Mode
5. SYSTEM MAINTENANCE REFERENCE
5.1 SERVICE PROGRAM MODE
ƒ
Make sure that the data-in LED () is not on before you go into the SP mode. This
LED indicates that some data is coming to the machine. When the LED is on, wait
for the copier to process the data.
5.1.1 SP TABLES
See "Appendices" for the following information:
ƒ
SP Tables
5.1.2 USING SERVICE PROGRAM MODES
Use the service program modes (SP modes) to check electrical data, change operating
modes, and adjust values.
The Service Program Mode is for use by service representatives only so that they
can properly maintain product quality. If this mode is used by anyone other than
service representatives for any reason, data might be deleted or settings might be
changed. In such case, product quality cannot be guaranteed any more.
Entering SP Mode
1.
Press the following sequence of keys.
"→→→→D
Or
" → D → Combine Key → 2.
Hold the D key down for longer than 3 seconds.
3.
The SP number is displayed. (e.g. SP1)
Leaving SP Mode
To exit SP mode, press Clear Modes/Recovery"
5.1.3 USING THE SP MODE
SP command numbers can be entered directly.
1.
Using the number keys, enter the desired main-menu number, then press the Enter
key.
SM
5-1
CÓPIA NÃO CONTROLADA
C274
System
Maintenance
Reference
ƒ
CÓPIA NÃO CONTROLADA
Service Program Mode
2.
Using the number keys, enter the desired sub-menu number, then press the Enter key.
3.
Enter the desired value using the number keys.
4.
Press the enter key to store the displayed setting.
C274
5-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
TROUBLESHOOTING
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Service Call Conditions
6. TROUBLESHOOTING
6.1 SERVICE CALL CONDITIONS
See "Appendices" for the following information:
SC tables
Troubleshooting
ƒ
SM
6-1
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Electrical Component Defects
6.2 ELECTRICAL COMPONENT DEFECTS
See "Appendices" for the following information:
ƒ
Electrical component defects
C274
6-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Fuse, LED, VR, DIP-SW, AND TP Tables
6.3 FUSE, LED, VR, DIP-SW, AND TP TABLES
See "Appendices" for the following information:
Fuse table
ƒ
LED table
ƒ
VR table
ƒ
DIP switch table
ƒ
Test point (TP) table
Troubleshooting
ƒ
SM
6-3
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
C274
SERVICE MANUAL APPENDICES
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
C274 APPENDICES
TABLE OF CONTENTS
1. APPENDIX: SPECIFICATIONS ................................................... 1-1
1.1 GENERAL SPECIFICATIONS ................................................................... 1-1
1.1.1 MAIN FRAME ................................................................................... 1-1
2. APPENDIX: MAINTENANCE TABLES ....................................... 2-1
2.1 MAINTENANCE TABLE............................................................................. 2-1
3. APPENDIX: SERVICE CALL CONDITION.................................. 3-1
3.1 SC TABLES ............................................................................................... 3-1
4. APPENDIX: ELECTRICAL COMPONENT DEFECTS ................ 4-1
4.1 ELECTRICAL COMPONENT DEFECTS ................................................... 4-1
4.2 FUSE, LED, VR, DIP-SW, AND TP TABLES............................................. 4-3
4.2.1 BLOWN FUSE CONDITIONS........................................................... 4-3
4.2.2 LED’S................................................................................................ 4-3
4.2.3 VR’S.................................................................................................. 4-4
4.2.4 DIP SWITCHES ................................................................................ 4-4
4.2.5 TEST POINTS .................................................................................. 4-5
5. APPENDIX: SP MODE TABLES ................................................. 5-1
5.1 INPUT MODE ............................................................................................ 5-1
5.1.1 SP TABLE......................................................................................... 5-1
5.2 OUTPUT MODE......................................................................................... 5-4
5.2.1 SP TABLE......................................................................................... 5-4
SP2-41: Thermal Head Signal Output (VHD Signal) ............................ 5-5
5.3 TEST MODE .............................................................................................. 5-6
5.3.1 SP TABLE......................................................................................... 5-6
SP3-1: Firmware Suffix Information...................................................... 5-6
5.4 ADJUSTMENT MODE ............................................................................... 5-7
5.4.1 SP TABLE......................................................................................... 5-7
SP6-42: Image Adjustment Pattern Print.............................................. 5-7
SM Appendix
i
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
APPENDIX:
SPECIFICATIONS
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
General Specifications
1. APPENDIX: SPECIFICATIONS
1.1 GENERAL SPECIFICATIONS
1.1.1 MAIN FRAME
Configuration
Desktop
Master Process
Digital with 300 dpi thermal head
Scanning (Pixel Density)
300 dpi
Originals
Sheet
Printing Process
Fully automatic one-drum stencil system
Original Size
Maximum: 275 x 395 mm / 10.8" x 15.6"
Minimum: 90 x 140 mm / 3.5" x 5.5"
Original Weight
40.7 – 127.9 g/m2
Copy Paper Size
Maximum: 275 x 395 mm / 10.8" x 15.6"
Minimum: 90 x 140 mm / 3.5" x 5.5"
Copy Paper Weight
35.0 – 127.9 g/m2 (10 to 30 °C)
Printing Speed
60, 90cpm (2 steps)
Reproduction Rations
Metric (%): 141, 122, 115, 93, 87, 82, 71
Inch (%): 155, 129, 121, 93, 77, 74, 65
Master Eject Box Capacity
30 masters
Paper Capacity
500 sheets (75 g/m2, 20 lb)
Paper Delivery Tray Capacity
500 sheets (80 g/m2, 20 lb)
Power Source
North America: 120 V, 60 Hz, 2.0 A
Europe/Asia: 220 - 240 V, 50/60 Hz, 1.1 A
Power Consumption
SM Appendix
110 - 120V: Less than 175W, Less than 2.9A
1-1
CÓPIA NÃO CONTROLADA
C274
Appendix:
Specifications
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
General Specifications
220 - 240V: Less than 175W, less than 1.3A
Noise Emission
Operating Position Sound Power Level:
Standby: Not above 22.5 db
Copying 60 rpm: Not above 64 db
Copying 90 rpm: Not above 68 db
Sound Power Level:
Standby: Not above 31.2 db
Copying 60 rpm: Not above 77 db
Copying 90 rpm: Not above 80 db
Dimensions (W x D x H)
Set up: 1332 x 672 x 519 mm (52.5" x 26.4" x
20.5")
Stored: 582 x 672 x 519 mm (23.0" x 26.4" x
20.5")
Weight
54 kg (119lb.)
Master Processing Time
Less than 40 seconds (A4, 8½" x 14)
First Print Time
Less than 42 seconds (A4, 8½" x 14)
Leading Edge Margin
5 mm ±3 mm
Side Registration Adjustable Range
+ 14mm to - 9mm
Vertical Registration Adjustable
±10 mm
Range
Master
Master type
280 mm width (B4), 50 m/roll
240 mm width (LG), 50 m/roll
Yield
100 masters/roll
Maximum run length per
2000 prints/master
master
Storage conditions
C274
0 to 40 °C, 10 to 95 %RH
1-2
CÓPIA NÃO CONTROLADA
SM Appendix
General Specifications
Ink
Storage period
One year after production date
Ink type
500 ml/pack (Black)
600 ml/pack (other colors)
Available colors
Black, Red, Blue, Green, Brown, Yellow, Violet,
Navy, Maroon, Orange, Hunter green
Storage conditions
-5 to 40 °C, 10 to 95 %RH
(Optimum conditions: 15 to 25°C, 20 to 70%RH)
Storage period
One year after production date (-5 to 40 °C)
18 months after production date (15 to 25 °C)
ƒ
Avoid locations exposed to direct sunlight.
SM Appendix
1-3
CÓPIA NÃO CONTROLADA
C274
Appendix:
Specifications
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
APPENDIX:
MAINTENANCE TABLES
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Maintenance Table
2. APPENDIX: MAINTENANCE TABLES
The following items should be maintained periodically. There are two sets of intervals - one
based on time and the other based on print count. For maintenance items with entries in
both of them, use whichever comes first.
Symbol key: C: Clean, R: Replace, L: Lubricate, A: Adjust
ƒ
Turn off the main power switch and unplug the machine before performing any
procedure in this section.
Internal Time
Item
6M
Print Counter
EM
1Y
2Y
5Y
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Note
150K 300K 600K 1.2M 3M
Scanner/Optics
CIS
1st Feed
Roller
2nd Feed
Roller
C
Damp
Cloth
Damp
Cloth
Dry Cloth,
Shading
Plate (White
Dry Cloth
C
C
C
Expected
C
life is 10k
Plate)
masters.
Master Feed
Thermal
Head
C
C
C
C
C
Alcohol
Platen Roller
C
C
Alcohol
Master End
C
C
Dry Cloth
SM Appendix
2-1
CÓPIA NÃO CONTROLADA
C274
Appendix:
Maintenance
Tables
2.1 MAINTENANCE TABLE
CÓPIA NÃO CONTROLADA
Maintenance Table
Sensor
Paper Feed
Paper Feed
C
R
R
R
C
R
R
R
Friction Pad
R
R
R
R
R
R
R
R
Press Roller
C
C
R
C
Roller
R
Exit Sensor
Registration
Sensor
C
C
C
C
Registration
C
Paper
Delivery Unit
Bushings
Cloth
Water or
Alcohol
C
Alcohol
C
Dry Cloth
C
Dry Cloth
Water or
C
Rollers
Damp
Alcohol
C
C
Motor Oil
L
L
(SAE #20)
Paper Feed
R
Clutch
Feed Start
Timing
C
Dry Cloth
Sensor
Drum and Ink Supply
Cloth Screen
Ink Nozzle
R
C
C
C
R
C
C
Drum
Clamper
Damp
Cloth
Water or
C
C
C
C
Alcohol
Plate/Magnet
Drum Master
C274
C
2-2
CÓPIA NÃO CONTROLADA
Dry Cloth
SM Appendix
CÓPIA NÃO CONTROLADA
Maintenance Table
Sensor
C
C
C
C
Dry Cloth
Drum Drive
Gear and
Grease
L
L
L
(Alvania#2)
Cam
SM Appendix
2-3
CÓPIA NÃO CONTROLADA
C274
Appendix:
Maintenance
Tables
Black Patch
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
APPENDIX:
SERVICE CALL CONDITION
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SC Tables
3. APPENDIX: SERVICE CALL CONDITION
3.1 SC TABLES
E-00
Symptom
Possible cause
Clamper error
Clamper drive
The MPU cannot detect the clamper position sensor
Clamper sensors
signal (open or closed) within 3.0 seconds after the
Clamper motor
Appendix:
Service Call
Condition
No.
clamper motor turns on.
E-01
E-03
Cutter error
Cutter drive
The cutter HP sensor does not turn on within 3.0
Cutter switch
seconds after the cutter motor turns on.
Cutter motor
Thermal Head ID Error
Thermal head
The CPU detects on abnormal ID signal from the
MPU
thermal head.
E-04
Thermal Head Overheat
Overheat (wait for the
The temperature of the thermal head is greater than
thermal head to cool
54°C when the Start key is pressed.
down)
Thermal head
E-06
E-09
Main Motor error
Main motor drive
The CPU cannot detect the master eject position
Main motor
sensor (drum HP) signal within 2.5 seconds after the
Motor drive board
main motor turns on.
Master eject position SN
Thermal Head Thermistor Open
Thermal head
The thermistor output voltage is over 4.9 volts.
thermistor
Thermal head
connector
E-10
Thermal Heard Drive Failure
Thermal head
The CPU detects an abnormal condition in the thermal
MPU
head drive circuit.
Thermal head
connector
SM Appendix
3-1
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
SC Tables
No.
E-12
Symptom
Possible cause
Pressure Plate error
Pressure plate drive
The pressure plate home position sensor signal is not
Pressure plate motor
detected within 3.0 seconds after the pressure plate
Plate position sensors
motor turns on.
MPU
IPU error
E-14
Signal transmission error (from the IPU) occurred in
the MPU
E-23
Master Eject Position Sensor (Drum HP) error
Master eject position
The master eject position sensor does not activate
sensor
before the feed start timing sensor activates.
Feed start timing sensor
Feeler
E-24
Feed Start Timing Sensor error
Master eject position
The feed start timing sensor does not activate before
sensor
the master eject sensor activates.
Feed start timing sensor
Feeler
C274
3-2
CÓPIA NÃO CONTROLADA
SM Appendix
CÓPIA NÃO CONTROLADA
APPENDIX:
ELECTRICAL COMPONENT
DEFECTS
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Electrical Component Defects
4. APPENDIX: ELECTRICAL COMPONENT
DEFECTS
Appendix:
Electrical
Component
Defects
4.1 ELECTRICAL COMPONENT DEFECTS
Component
Condition
Open
Original Sensor
Shorted
Open
Symptom
The P jam indicator is lit whenever the main switch is
on.
The P jam indicator is lit whenever a master is made.
The E jam indicator is lit whenever the main switch is
on.
Master Eject Sensor
Shorted
Pressure Plate HP
Sensor
Pressure Plate Limit
Sensor
SM Appendix
Open
The E jam indicator is lit whenever a used master is
ejected.
E-12 is displayed whenever the main switch is on.
Shorted
Open
E-12 is displayed whenever the main switch is on.
Shorted
The master eject indicator is lit whenever the main
4-1
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Electrical Component Defects
Component
Condition
Symptom
switch is on.
Feed Start Timing
Sensor
Master Eject
Open
E-6 is displayed whenever the main switch is on.
Shorted
E-24 is displayed whenever the main switch is on.
Open
E-6 is displayed whenever the main switch is on.
Shorted
E-23 is displayed whenever the main switch is on.
Position (Drum HP)
Sensor
Open
Drum Master
Sensor
Shorted
Open
Paper Exit Sensor
Shorted
C274
The D jam indicator is lit whenever a proof print is
made.
The D jam indicator is lit whenever a master is made.
The M indicator is lit whenever a copy is made.
The C jam indicator is lit whenever the main switch is
on.
The B jam indicator is lit whenever a copy is made.
4-2
CÓPIA NÃO CONTROLADA
SM Appendix
CÓPIA NÃO CONTROLADA
Fuse, LED, VR, DIP-SW, and TP Tables
4.2 FUSE, LED, VR, DIP-SW, AND TP TABLES
4.2.1 BLOWN FUSE CONDITIONS
MPU
No.
Rate
FU101
1A
No.
Rate
FU700
6.3 A
FU701
6.3 A
Possible cause
Ink pump motor
PSU
Possible cause
AC Line
Appendix:
Electrical
Component
Defects
Main motor
Main motor control board
Paper feed clutch
Air knife fan motor
Front/Rear pressure release solenoid
Vacuum fan motor
Ink pump motor
FU702
6.3 A
Master eject motor
Master/Paper counter
Contact Image Sensor (CIS)
Pressure plate motor
Scanner motor
Clamper motor
Master feed motor
4.2.2 LED’S
MPU
No.
LED103
SM Appendix
Function
OFF: Low ink condition
ON: Sufficient ink condition
4-3
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Fuse, LED, VR, DIP-SW, and TP Tables
4.2.3 VR’S
MPU
No.
VR101
Function
Adjust the ink detection. ( Replacement and Adjustment – Drum - Ink
Detection Adjustment)
VR102
Adjust the master end sensor. ( Replacement and Adjustment – Master
Feed - Master End Sensor Adjustment)
PSU
No.
VR1
Function
Adjust the thermal head voltage. ( Replacement and Adjustment - Master
Feed - Thermal Head Voltage Adjustment)
4.2.4 DIP SWITCHES
MPU
DIPSW
No.
Bit No.
1 to 4
Name
Settings
Paper Registration Position
( Replacement and Adjustment –
Adjust
Image Adjustment - DIPSW101 No.1 to
4 – Paper Registration Position
Adjustment)
101
5 to 8
Master Writing Position
( Replacement and Adjustment –
Adjust
Image Adjustment - DIPSW101 No.5 to
8 – Master Writing Position Adjustment)
102
1 to 3
Thermal Head Energy
( Replacement and Adjustment –
Control
Image Adjustment - DIPSW102 No.1 to
3 – Thermal Head Energy Control)
4
5
C274
Not used
-
Drum Size Selection
ON: LG
4-4
CÓPIA NÃO CONTROLADA
SM Appendix
CÓPIA NÃO CONTROLADA
Fuse, LED, VR, DIP-SW, and TP Tables
DIPSW
No.
Bit No.
Name
Settings
OFF: B4
6
7
8
1 to 4
Size in Metric or Inch
ON: inch
OFF: mm
Panel Beeper
ON: Enabled
OFF: Disabled
Not used
-
Scanning Speed
( Replacement and Adjustment –
Adjustment
Image Adjustment - DIPSW103 No.1 to
5 to 8
Master Feeding Speed
( Replacement and Adjustment –
Adjustment
Image Adjustment - DIPSW103 No.5 to
8 – Master Feeding Speed Adjustment)
4.2.5 TEST POINTS
MPU
No.
Function
TP101
GND
TP103
Measures the ink detection pulse
TP104
Measures the ink detection pulse (standard pulse)
TP113
GND
PSU
No.
Function
TP701
Thermal head voltage
TP702
GND
SM Appendix
4-5
CÓPIA NÃO CONTROLADA
C274
Appendix:
Electrical
Component
Defects
4 – Scanning Speed Adjustment)
103
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
APPENDIX:
SP MODE TABLES
R E V I S I O N H I S T O RY
P a ge
Date
A d de d /U pd at e d /N ew
None
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Input Mode
5. APPENDIX: SP MODE TABLES
5.1 INPUT MODE
5.1.1 SP TABLE
No.
Name
1-3
Original Sensor
1-26
Master End Sensor
1-27
Ink Detection Signal
1-31
Pressure Plate Home Position
Note
Sensor
Pressure Plate Limit Position Sensor
1-33
Master Eject Box Set Sensor
1-42
Paper Exit Sensor
1-43
Master Eject Sensor
1-44
Drum Master Sensor
1-52
Door Safety Switch
Appendix:
SP Mode
Tables
1-32
Master Making Unit Set Sensor
1-53
Cutter Home Position Sensor
1-56
Feed Start Timing Sensor
1-59
Master Eject Position Sensor
1-62
Drum Set Signal
1-65
Clamper Close Sensor
1-66
Clamper Open Sensor
SM Appendix
5-1
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Input Mode
No.
Name
1-68
Paper Registration Sensor
1-70
Master Set Cover Sensor
1-71
DIPSW 103-1
Note
Use these SPs to test whether the DIP
switches are working properly.
1-72
DIPSW 103-2
1-73
DIPSW 103-3
1-74
DIPSW 103-4
1-75
DIPSW 103-5
1-76
DIPSW 103-6
1-77
DIPSW 103-7
1-78
DIPSW 103-8
1-79
DIPSW 101-1
1-80
DIPSW 101-2
1-81
DIPSW 101-3
1-82
DIPSW 101-4
1-83
DIPSW 101-5
1-84
DIPSW 101-6
1-85
DIPSW 101-7
1-86
DIPSW 101-8
C274
5-2
CÓPIA NÃO CONTROLADA
SM Appendix
CÓPIA NÃO CONTROLADA
Input Mode
No.
Name
DIPSW 102-1
1-88
DIPSW 102-2
1-89
DIPSW 102-3
1-90
DIPSW 102-4
1-91
DIPSW 102-5
1-92
DIPSW 102-6
1-93
DIPSW 102-7
1-94
DIPSW 102-8
Appendix:
SP Mode
Tables
1-87
Note
SM Appendix
5-3
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Output Mode
5.2 OUTPUT MODE
5.2.1 SP TABLE
No.
Name
Note
2-3
Master Eject Motor
2-6
Vacuum Fan Motor
2-7
Air Knife Fan Motor
2-9
Master Counter
2-10
Paper Counter
2-12
Ink Pump Motor
2-14
Pressure Release Solenoids
2-21
Exposure Lamp (Xenon Lamp)
2-22
Cutter Motor: + direction
2-23
Cutter Motor: to Home
2-24
Cutter Motor: - direction
2-27
Main Motor: to drum home position
2-28
Main Motor: to master making
Press and hold the master making key
to start the test. Release the key to stop
the test.
position
2-36
Master Feed Motor
2-37
Scanner Motor
2-41
Thermal Head Signal Output (VHD
Signal) ( Explanation Below)
2-42
Paper Feed Clutch
2-44
Clamper Motor: to close
C274
5-4
CÓPIA NÃO CONTROLADA
SM Appendix
CÓPIA NÃO CONTROLADA
Output Mode
No.
Name
2-45
Clamper Motor: to open
2-46
Pressure Plate Motor: to limit
2-47
Pressure Plate Motor: to home
Note
position
Main Motor: 30rpm
2-49
Main Motor: 60rpm
2-50
Main Motor: 90rpm
2-51
Paper Feed Motor: 30rpm
No.
Name
2-52
Paper Feed Motor: 60rpm
2-53
Paper Feed Motor: 90rpm
Note
Press and hold the master making key
to start the test. Release the key to stop
the test.
Appendix:
SP Mode
Tables
2-48
SP2-41: Thermal Head Signal Output (VHD Signal)
Applies thermal head voltage.
Power is applied by pressing the # key. To protect the thermal head, the voltage supply is
automatically stopped after 30 seconds. It is also stopped by pressing the clear/stop key.
( Replacement and Adjustment – Master Feed - Thermal Head Voltage Adjustment)
SM Appendix
5-5
CÓPIA NÃO CONTROLADA
C274
CÓPIA NÃO CONTROLADA
Test Mode
5.3 TEST MODE
5.3.1 SP TABLE
No.
Name
3-1 Firmware Suffix
Function
( Explanation Below)
Information
3-4 All Indicators ON
Turns on all the indicators on the operation panel by
pressing the master making key.
3-5 Test Pattern Print
Print the thermal head test pattern by pressing the
master making key.
3-6 Ink Detection
Specifies whether ink detection is done.
0: OFF
1: ON (Default)
The setting value returns to default value in power
switch off.
SP3-1: Firmware Suffix Information
This model has no LCD, so the suffix is displayed as shown below instead of in Latin
letters.
ƒ
C274
The letters “i”, “o” and “u” are always skipped.
5-6
CÓPIA NÃO CONTROLADA
SM Appendix
CÓPIA NÃO CONTROLADA
Adjustment Mode
5.4 ADJUSTMENT MODE
5.4.1 SP TABLE
No.
6-40
Name
Function
Ink Detection Adjustment
( Replacement and Adjustment – Drum - Ink
Detection Adjustment)
6-41
6-42
Master End Sensor
( Replacement and Adjustment – Master Feed -
Adjustment
Master End Sensor Adjustment)
Image Adjustment Pattern
( Explanation below)
Print
SP6-42: Image Adjustment Pattern Print
This test pattern is used for master feeding speed adjustment.
ƒ
Master Feeding Speed Adjustment: ( Replacement and Adjustment – Image
This test pattern is generated in the MPU, and does not use the scanner unit. So, this
pattern can also be used to determine whether an image problem is caused by the scanner
or the thermal head.
If there is an image problem during copying but the test print is OK, the problem could be in
the scanner unit.
The print paper should be B4 or LG size when using this test pattern.
SM Appendix
5-7
CÓPIA NÃO CONTROLADA
C274
Appendix:
SP Mode
Tables
Adjustment - DIPSW103 No.5 to 8 – Master Feeding Speed Adjustment)
Download PDF