Radiant Festoon Fixture

Radiant Festoon Fixture
Linear Low Voltage
he Radiant Low Voltage Lighting System is the
Specifier's choice for architectural coves requiring
continuous dramatic lighting. Designed to
complement a wide range of design possibilities and
add excitement to both interior and exterior, the Radiant
System was designed specifically for long run, long life
commercial and residential lighting applications.
T
The Radiant Low Voltage Lighting System takes a new and
innovative approach to interior and exterior lighting
applications by solving many problems associated with low
voltage lighting. Radiant fixtures mold to conform to unusual
shapes and irregular coves without field drawings and can
be field cut and modified to conform to actual job
requirements. The strip to strip connector assemblies provide
electrical connections and polarization with one screw and
integral sockets provide continuous illumination over long
lengths. A secondary 25A circuit is built into each strip to
ensure steady, even light distribution over long runs while
doubling the current carrying capacity of any miniature light
strip. Ultra High Temperature Thermoplastic provides a heat
resistant surface material as well as an unusual amount of
flexibility. Xenon and incandescent, low voltage lamps are
designed specifically for long life commercial applications.
These lamps are available in clear to provide sharp, crisp
lighting or frosted for a soft wash of light. Indexed Lamp
Clips lock in position to maintain lamp spacing along curves
and corners. Finally, a wide range of precision engineered
accessories have been developed to allow complete and
creative presentations.
About Radiant
The Radiant Low Voltage Lighting System represents the
marriage of superior technology, precision engineering and
innovative design which combine to create highly efficient,
highly effective specialized lighting equipment. The designs
and engineering accomplishments featured here are the
result of an ongoing collaborative effort between David
Morgan of DMA and Bruce Belfer of the Belfer Group.
Multiple patents are pending.
2
Table of Contents:
Fixtures and Accessory Details
Festoon Fixtures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
24 Volt, 10 Watt Festoon Strip . . . . . . . . . . . . . . . . . . . .11
24 Volt, 5 Watt Festoon Strip . . . . . . . . . . . . . . . . . . . . .13
24 Volt, 3 Watt Festoon Strip . . . . . . . . . . . . . . . . . . . . .15
12 Volt, 10 Watt Festoon Strip . . . . . . . . . . . . . . . . . . . .17
12 Volt, 5 Watt Festoon Strip . . . . . . . . . . . . . . . . . . . . .19
Festoon System Accessory Details . . . . . . . . . . . . . . . .10
RAD 204 Live End Feed . . . . . . . . . . . . . . . . . . . . . . . . .10
RAD 201F Thru Circuit Connector . . . . . . . . . . . . . . . . . .12
RAD 203F Crossover Circuit Connector . . . . . . . . . . . . . .14
RAD 209 Thru Circuit Adjustable Angle Corner Connection 16
RAD 301 and 302 Swivel Lamp Holders . . . . . . . . . . . . . .18
RAD 202 Thru Circuit Flexible Connector . . . . . . . . . . . . .30
RAD 210 Universal Thru Circuit Connector Feed . . . . . . . .30
RAD 401 Dead End Termination . . . . . . . . . . . . . . . . . . .31
RAD 402 Mounting Clip . . . . . . . . . . . . . . . . . . . . . . . . .31
RAD 403 Right Angle Bracket . . . . . . . . . . . . . . . . . . . . .31
Rigid Loop Fixtures . . . . . . . . . . . . . . . . . . . . . . . . . . .20
24 Volt, 10 Watt Rigid Loop Strip . . . . . . . . . . . . . . . . . .23
24 Volt, 5 Watt Rigid Loop Strip . . . . . . . . . . . . . . . . . . .25
12 Volt, 10 Watt Rigid Loop Strip . . . . . . . . . . . . . . . . . .27
12 Volt, 5 Watt Rigid Loop Strip . . . . . . . . . . . . . . . . . . .29
Rigid Loop System Accessory Details . . . . . . . . . . . . .22
RAD 204 Live End Feed . . . . . . . . . . . . . . . . . . . . . . . . .22
RAD 201L Thru Circuit Connector . . . . . . . . . . . . . . . . . .24
RAD 203L Crossover Circuit Connector . . . . . . . . . . . . . .26
RAD 209 Thru Circuit Adjustable Angle Corner Connection 28
RAD 202 Thru Circuit Flexible Connector . . . . . . . . . . . . .30
RAD 210 Universal Thru Circuit Connector Feed . . . . . . . .30
RAD 401 Dead End Termination . . . . . . . . . . . . . . . . . . .31
RAD 402 Mounting Clip . . . . . . . . . . . . . . . . . . . . . . . . .31
RAD 403 Right Angle Bracket . . . . . . . . . . . . . . . . . . . . .31
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Lamp Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .34
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Field Modifications . . . . . . . . . . . . . . . . . . . . . . . . . .40
The Radiant CheckSum Circuit Calculator . . . . . . . . . .41
Fixture Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Table of Contents
The Radiant Advantage . . . . . . . . . . . . . . . . . . . . . . . . .4
The Radiant Two Circuit System . . . . . . . . . . . . . . . . . . . . .6
Radiant CheckSum System . . . . . . . . . . . . . . . . . . . . . . . .6
3
THE RADIANT ADVANTAGE
The Radiant Low Voltage Lighting System offers
many distinct installation and maintenance advantages:
Integrated Vertical Connector Assembly makes short work of all
connections...strip to strip or strip to feed, all four connectors are
automatically polarized and joined with one single screw
Two 25 Amp Circuits double the current carrying capacity of any
miniature light strip
1200 watts @ 24 volts
600 watts @ 12 volts
Strip to Strip Connector Assembly with integral sockets for
continuous illumination
Integrated Vertical Connector Assembly eliminates wirenuts, screw
terminals, tab connections and junctions boxes... all the installation
headaches normally associated with miniature low voltage systems
Indexed Lamp Clip Assembly retains on center spacing in any
curved or straight configuration
Multiple Patents Pending
The Radiant Advantage
Two lamp styles:
4
Festoon
Rigid Loop
Two 25 Amp Circuits
Double the amperage
Double the length
Integrated Vertical
Connector Assembly
Indexed Lamp
Clip Assembly
Lamps stay in place
Accepts all Radiant connectors
Strip to Strip
Connector Assembly
The Radiant Advantage
Integral sockets for
continuous light
5
THE RADIANT TWO
CIRCUIT SYSTEM
NEC 411 and UL 1598 specify that the maximum allowable
circuit is 25 Amps
In order to overcome restrictions this 25 Amp limit, we
have included a 2nd 25 Amp circuit in the fixture itself
No complex calculations are needed
The second 25 Amp circuit is automatically accessed with
any of our RAD 200 series connector accessories
RADIANT CHECKSUM™ SYSTEM
THE RADIANT CHECKSUM SYSTEM is our unique, simple and accurate method of ensuring that every Radiant Linear Low
Voltage System is properly circuited and meets applicable U.L. and N.E.C. codes, which allow a maximum of 25 amps per
Low Voltage circuit.
TRADITIONAL AMPERAGE CALCULATIONS
Traditionally extensive calculations were necessary to determine the size and number of transformers, circuits, feed locations
and overcurrent protection devices needed for a linear low voltage system.
HERE IS THE MATH
FOR EXAMPLE
317 linear feet of linear low voltage
strip with 5 watt lamps, 2.125 inches
on center, 24 volts (all Radiant Linear
Low Voltage strips are 2.125 inches
(54 mm) on center)
317 feet x 12 inches/foot =
3804 inches / 2.125 inches on center =
1790 lamps x 5 watts/lamp =
8950 watts / 24 volts =
373 amps x 1.06 (6% Load Margin) =
396 amps / 25 amps/circuit =
3804 inches
1790 lamps
8950 watts
373 amps
396 amps
15.84
16 circuits
25 amps each
Radiant Two Circuit System
note: always round up
6
THE RADIANT CHECKSUM SYSTEM eliminates all the traditional calculations associated with low voltage products. The
✔ SUM™ is precalculated based upon the voltage and amperage characteristics of 12 and 24 volt systems, including a
Load Margin.
Radiant Low Voltage
Linear Feet
Volt
12V
24V
✔ SUM
50
100
Radiant Low Voltage
Linear Meters
Volt
12V
24V
✔ SUM
15
30
THE ENTIRE CALCULATION IS DONE IN TWO STEPS:
total footage x watts/lamp =
load factor / CHECKSUM =
load factor
number of 25 amp circuits required
note: always round up
THE RADIANT CHECKSUM SYSTEM calculates the number of circuits quickly and accurately.
Using the same example as before
317 linear feet of linear low voltage strip with 5 watt lamps, 2.125 inches on center, 24 volts
(all Radiant Linear Low Voltage strips are 2.125 inches (54 mm) on center)
For a 24 Volt System in linear feet, the ✔ SUM™ = 100
317 feet x 5 watts/lamp =
1585 /100 (✔ SUM) =
1585 load factor
15.85
16 circuits
25 amps each
THE RADIANT CHECKSUM SYSTEM WORKS EVERY TIME!
Using this simple system consistently ensures sufficient circuit counts for any project of any size, and
automatically includes a reasonable Load Margin. All Power Supplies and Transformers are listed by
voltage and number of 25 Amp circuits, thus making the specification and quotation processes faster,
easier and considerably more user friendly.
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
Radiant Checksum System
note: always round up
7
FESTOON
APPLICATIONS
Radiant Festoon Low Voltage Light Strips are best suited to
applications where the light strips may be visible as part of
Festoon Applications
the decorative nature of the installation.
8
Signage
Ceiling Coves
Wall Coves
Display Cases
Under-Cabinet Lighting
Shelf Lighting
Architectural Accents
Stairways
Festoon Applications
Decorative Accents
9
ACCESSORY DETAIL
Live End Feed
• Smallest 50 Amp connector available
• Feeds upper (lit) and lower (spare) circuits
• Compatible with romex and metal conduit
• Accepts up to 10 gauge (30 Amp) conductors
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors
with a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
Festoon 24 Volt, 10 Watt
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
10
RAD 204
RAD LV 225 F
24 VOLTS, 10 WATTS
FESTOON LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .55.0
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .2.3
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . .11.0
.800”
20.5mm
(actual size)
✔sum = 100
FIXTURE
SOCKET
LENGTH
LAMP
VOLTAGE
WATTAGE
❍
❍ F (festoon)
❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ IC (incandescent clear)
❍ 24 (24 volts)
❍ 10 (10 watts)
RAD LV 225
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 F LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
10 Watt Xenon and Incandescent Festoon Lamps available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6’, 8' and 10'
ALR, MR8 and MR11 Swivel Lamp Holders are easily inserted
Lengths can be field cut
swivel lamp holders are found on page 18
Festoon 24 Volt, 10 Watt
Integral Connector Assembly
Electronic or Magnetic power supplies are available
power supply details are found on page 36
Multiple Patents Pending
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
11
ACCESSORY DETAIL
Thru Circuit Connector
• Intended for use in the middle of a 25 Amp
length
• Designed to carry both 25 Amp circuits straight
through a strip to strip connection
• Integral festoon sockets allow for seamless
illumination through connection
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors
with a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending))
Festoon 24 Volt, 5 Watt
RAD 201 F
12
RAD LV 225 F
24 VOLTS, 5 WATTS
FESTOON LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .27.0
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .1.2
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . .22.0
.800”
20.5mm
(actual size)
✔sum = 100
FIXTURE
SOCKET
LENGTH
LAMP
VOLTAGE
WATTAGE
❍
❍ F (festoon)
❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ IC (incandescent clear)
❍ IF (incandescent frost)
❍ 24 (24 volts)
❍ 5 (5 watts)
RAD LV 225
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 F LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High Temperature Thermoplastic
(U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
5 Watt Xenon and Incandescent Festoon Lamps available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6’, 8' and 10'
ALR, MR8 and MR11 Swivel Lamp Holders are easily inserted
Lengths can be field cut
swivel lamp holders are found on page 18
Integral Connector Assembly
power supply details are found on page 36
Festoon 24 Volt, 5 Watt
Electronic or Magnetic power supplies are available
Multiple Patents Pending
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
13
ACCESSORY DETAIL
Crossover Circuit Connector
• Designed to access the second 25 Amp circuit
while automatically terminating the first
• Intended for use at the end of the first 25 Amp
length to provide power for the second 25 Amp
length
• Integral festoon sockets allow for seamless
illumination through connection
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors
with a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
Festoon 24 Volt, 3 Watt
RAD 203 F
14
RAD LV 225 F
24 VOLTS, 3 WATTS
FESTOON LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .16.5
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .1.0
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . .36.0
.800”
20.5mm
(actual size)
✔sum = 100
FIXTURE
SOCKET
LENGTH
LAMP
VOLTAGE
WATTAGE
❍
❍ F (festoon)
❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ IC (incandescent clear)
❍ 24 (24 volts)
❍ 3 (3 watts)
RAD LV 225
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 F LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
3 Watt Xenon and Incandescent Festoon Lamps available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6’, 8' and 10'
ALR, MR8 and MR11 Swivel Lamp Holders are easily inserted
Lengths can be field cut
swivel lamp holders are found on page 18
Integral Connector Assembly
power supply details are found on page 36
Festoon 24 Volt, 3 Watt
Electronic or Magnetic power supplies are available
Multiple Patents Pending
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
15
ACCESSORY DETAIL
Thru Circuit Adjustable Angle
Corner Connection
• Allows an adjustable 0º to 180º angle
connection between strips
• Designed to carry both 25 Amp circuits straight
through a strip to strip connection
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors
with a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
Festoon 12 Volt, 10 Watt
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
16
RAD 209
RAD LV 225 F
12 VOLTS, 10 WATTS
FESTOON LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .55.0
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .4.6
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . . .5.0
.800”
20.5mm
(actual size)
✔sum = 50
FIXTURE
SOCKET
LENGTH
LAMP
VOLTAGE
WATTAGE
❍
❍ F (festoon)
❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ IC (incandescent clear)
❍ 12 (12 volts)
❍ 10 (10 watts)
RAD LV 225
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 F LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
10 Watt Xenon and Incandescent Festoon Lamps available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6’, 8' and 10'
ALR, MR8 and MR11 Swivel Lamp Holders are easily inserted
Lengths can be field cut
swivel lamp holders are found on page 18
Festoon 12 Volt, 10 Watt
Integral Connector Assembly
Electronic or Magnetic power supplies are available
power supply details are found on page 36
Multiple Patents Pending
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
17
ACCESSORY DETAIL
Swivel Lamp Holders
RAD 301
• Allow the use of Micro Reflector or Aluminum
Reflector Halogen lamps in the linear light strip
• 20 watt (max) MR8 or MR11 lamps (RAD 301)
• 20 watt (max) ALR lamps (RAD 302)
• Specialty lampholders snap directly into the
standard festoon socket in any location
• Exclusive locking mechanism allows for easy
positioning and maintenance of aiming selections
• Available for use in festoon fixtures only
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
Festoon 12 Volt, 5 Watt
RAD 302
18
RAD LV 225 F
12 VOLTS, 5 WATTS
FESTOON LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .27.5
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .2.3
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . .11.0
.800”
20.5mm
(actual size)
✔sum = 50
FIXTURE
SOCKET
LENGTH
LAMP
VOLTAGE
WATTAGE
❍
❍ F (festoon)
❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ IC (incandescent clear)
❍ IF (incandescent frost)
❍ 12 (12 volts)
❍ 5 (5 watts)
RAD LV 225
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 F LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
5 Watt Xenon and Incandescent Festoon Lamps available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6’, 8' and 10'
ALR, MR8 and MR11 Swivel Lamp Holders are easily inserted
Lengths can be field cut
swivel lamp holders are found on page 18
Integral Connector Assembly
power supply details are found on page 36
Festoon 12 Volt, 5 Watt
Electronic or Magnetic power supplies are available
Multiple Patents Pending
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
19
RIGID LOOP
APPLICATIONS
Radiant Rigid Loop Low Voltage Light Strips are best
suited to applications where lamp replacement and
Rigid Loop Applications
maintenance are priority considerations.
20
Sign/Backlighting
Ceiling Coves
Wall Coves
Display Cases
Under-Cabinet Lighting
Shelf Lighting
Architectural Accents
Rigid Loop Applications
Decorative Accents
21
ACCESSORY DETAIL
Live End Feed
• Smallest 50 Amp connector available
• Feeds upper (lit) and lower (spare) circuits
• Compatible with romex and metal conduit
• Accepts up to 10 gauge (30 Amp) conductors
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors
with a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
Rigid Loop 24 Volt, 10 Watt
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
22
RAD 204
RAD LV 225 L
24 VOLTS, 10 WATTS
RIGID LOOP LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .55.0
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .2.3
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . .11.0
.800”
20.5mm
(actual size)
✔sum = 100
FIXTURE
SOCKET
❍
❍ L (rigid loop) ❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
RAD LV 225
LENGTH
LAMP
VOLTAGE
WATTAGE
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ 24 (24 volts)
❍ 10 (10 watts)
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 L LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
10 Watt Xenon Rigid Loop Lamps are available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6', 8' and 10'
Lengths can be field cut
Rigid Loop 24 Volt, 10 Watt
Electronic or Magnetic power supplies are available
power supply details are found on page 36
Integral Connector Assembly
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
Multiple Patents Pending
•
Fax: 732.695.0145
•
www.radiantlighting.com
23
ACCESSORY DETAIL
Thru Circuit Connector
• Intended for use in the middle of a 25 Amp
length
• Designed to carry both 25 Amp circuits straight
through a strip to strip connection
• Integral rigid loop sockets allow for seamless
illumination through connection
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors with
a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
Rigid Loop 24 Volt, 5 Watt
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
24
RAD 201 L
RAD LV 225 L
24 VOLTS, 5 WATTS
RIGID LOOP LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .27.5
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .1.2
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . .22.0
.800”
20.5mm
(actual size)
✔sum = 100
FIXTURE
SOCKET
❍
❍ L (rigid loop) ❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
RAD LV 225
LENGTH
LAMP
VOLTAGE
WATTAGE
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ 24 (24 volts)
❍ 5 (5 watts)
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 L LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
5 Watt Xenon Rigid Loop Lamps are available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6', 8' and 10'
Electronic or Magnetic power supplies are available
Lengths can be field cut
Rigid Loop 24 Volt, 5 Watt
power supply details are found on page 36
Integral Connector Assembly
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
Multiple Patents Pending
•
Fax: 732.695.0145
•
www.radiantlighting.com
25
ACCESSORY DETAIL
Crossover Circuit Connector
• Designed to access the second 25 Amp circuit
while automatically terminating the first
• Intended for use at the end of the first 25 Amp
length to provide power for the second 25 Amp
length
• Integral rigid loop sockets allow for seamless
illumination through connection
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors with
a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
Rigid Loop 12 Volt, 10 Watt
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
26
RAD 203L
RAD LV 225 F
12 VOLTS, 10 WATTS
RIGID LOOP LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .55.0
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .4.6
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . . .5.0
.800”
20.5mm
(actual size)
✔sum = 50
FIXTURE
SOCKET
❍
❍ L (rigid loop) ❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
RAD LV 225
LENGTH
LAMP
VOLTAGE
WATTAGE
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ 12 (12 volts)
❍ 10 (10 watts)
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 L LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
10 Watt Xenon Rigid Loop Lamps are available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6', 8' and 10'
Lengths can be field cut
Rigid Loop 12 Volt, 10 Watt
Electronic or Magnetic power supplies are available
power supply details are found on page 36
Integral Connector Assembly
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
Multiple Patents Pending
•
Fax: 732.695.0145
•
www.radiantlighting.com
27
ACCESSORY DETAIL
Thru Circuit Adjustable Angle
Corner Connection
• Allows an adjustable 0º to 180º angle
connection between strips.
• Designed to carry both 25 Amp circuits straight
through a strip to strip connection
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors with
a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
Rigid Loop 12 Volt, 5 Watt
RAD 209
28
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
RAD LV 225 F
12 VOLTS, 5 WATTS
RIGID LOOP LOW VOLTAGE LIGHT STRIP
.885”
22.5mm
Lamps per foot . . . . . . . . . . . . . . . . . . . . . . . .5.5
Watts per foot . . . . . . . . . . . . . . . . . . . . . . .27.0
Amps per foot . . . . . . . . . . . . . . . . . . . . . . . .2.3
Feet per 25 amps . . . . . . . . . . . . . . . . . . . . .11.0
.800”
20.5mm
(actual size)
✔sum = 50
FIXTURE
SOCKET
❍
❍ L (rigid loop) ❍ 02 (2’ length)
❍ 04 (4’ length)
❍ 05 (5’ length)
❍ 06 (6’ length)
❍ 08 (8’ length)
❍ 10 (10’ length)
❍ F (linear per foot)
RAD LV 225
LENGTH
LAMP
VOLTAGE
WATTAGE
❍ XC (xenon clear)
❍ XF (xenon frost)
❍ 12 (12 volts)
❍ 5 (5 watts)
Lengths are nominal. Refer to page 41 for actual lengths
To order RAD LV 225 fixture without lamps, please specify RAD LV 225 L LENGTH only
a Belfer/DMA design
PRODUCT FEATURES
Constructed of Proprietary Ultra High
Temperature Thermoplastic (U.L. Recognized)
Indexed Sockets lock in position to maintain lamp spacing
2.125" (54mm) on center lamp spacing
accessory details are found on page 32
5 Watt Xenon Rigid Loop Lamps are available
Field Curvable to 12" radius (305mm)
Connector Accessories are available
lamp details are found on page 34
Standard lengths are 2', 4', 5', 6', 8' and 10'
Electronic or Magnetic power supplies are available
Lengths can be field cut
Rigid Loop 12 Volt, 5 Watt
power supply details are found on page 36
Integral Connector Assembly
2 - 25 Amp Circuits, specifically designed to conform to
U.L. 1598 and N.E.C. 411
LIGHTING
•
Tel: 732.695.0144
Multiple Patents Pending
•
Fax: 732.695.0145
•
www.radiantlighting.com
29
ACCESSORY DETAIL
RAD 202
Thru Circuit Flexible Connector
RAD 210
Universal Thru Circuit
Connector Feed (Not Shown)
• Can be field modified to crossover circuit
• Single circuit connection when no second
25 Amp circuit required
• Designed to carry both 25 Amp circuits straight
through a strip to strip connection
• Eliminates wire nuts, terminal blocks and
junction hardware
• Connects to strip and to all four conductors with
a single screw
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
• Can be field modified to crossover circuit
• Can be mounted in any location along the length
of the strip
• Eliminates wire nuts, terminal blocks and
junction hardware
• Silver plated contacts for superior conductivity
and near-zero voltage drop through the
connection
• Automatically maintains correct polarity
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
Accessory Detail RAD202, RAD210
• UL and CUL listed, Class 1 System, suitable for
installation in any locale
(patents pending)
30
RAD 202
RAD 402
Mounting Clip
RAD 403
Right Angle Bracket
• For termination of field cut pieces
• Exclusive slot allows for extra easy
installation
• Useful for curves and compound
curves
• Secures strip to surface
• Secures strip to surface
• Snaps tightly to strip
• Snaps tightly to strip
• Can be positioned anywhere
• Can be positioned anywhere
• Two mounting options
• Two mounting options
(4 count)
• No tools required
(4 count)
• Exclusive slot allows for extra easy
installation
(4 count)
RAD 401
RAD 402
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
RAD 403
•
www.radiantlighting.com
Accessory Detail RAD401, RAD402, RAD403
RAD 401
Dead End Termination
31
ACCESSORIES:
Strip to Strip Connectors
Radiant Strip to Strip Connectors are precision engineered to allow for a variety of creative installations.
Intended for use in the middle of a 25 Amp length, each connector:
• eliminates wire nuts, terminal blocks and junction hardware
• connects all four conductors with a single screw per strip
• utilizes silver plated contacts for superior conductivity and near-zero voltage drop through the connection
• automatically maintains correct polarity
Radiant Accessories
Radiant Strip to Strip connectors are UL and CUL listed, Class 1 System, suitable for installation in any locale. (patents pending)
32
❍ RAD 201F
Thru Circuit Connector (Festoon)
Designed to carry both 25 Amp circuits straight through a strip to
strip connection. Integral festoon sockets allow for seamless
illumination through connection.
(see page 12 for details)
❍ RAD 201L
Thru Circuit Connector (Rigid Loop)
Designed to carry both 25 Amp circuits straight through a strip to
strip connection. Integral rigid loop sockets allow for seamless
illumination through connection.
(see page 24 for details)
❍ RAD 202
Thru Circuit Flexible Connector
Designed to carry both 25 Amp circuits straight through a strip
to strip connection.
(see page 30 for details)
❍ RAD 203F
Crossover Circuit Connector (Festoon)
Designed to access the second 25 Amp circuit while automatically
terminating the first. Integral festoon sockets allow for seamless
illumination through connection.
(see page 14 for details)
❍ RAD 203L
Crossover Circuit Connector (Rigid Loop)
Designed to access the second 25 Amp circuit while automatically
terminating the first. Integral rigid loop sockets allow for seamless
illumination through connection.
(see page 26 for details)
❍ RAD 204
Live End Feed
Designed to feed upper (lit) and lower (spare) circuits.
Compatible with romex or metal conduit.
(see page 10 and 22 for details)
❍ RAD 209
Thru Circuit Adjustable Angle Corner Connection
Designed to carry both 25 Amp circuits straight through a strip to
strip connection while allowing an adjustable 0º to 180º angle
connection between strips.
(see page 16 and 28 for details)
❍ RAD 210
Universal Thru Circuit Connector Feed (not shown)
Designed to allow for a single circuit connection when no
second 25 Amp circuit is required
(see page 30 for details)
ACCESSORIES:
Aimable Lamp Holders
Radiant Aimable Lamp Holders allow the use of MR, ALR or Halogen lamps in the linear light strip.
• specialty lampholders snap directly into the standard festoon socket in any location
• exclusive locking mechanism allows for easy positioning and maintenance of aiming selections
Radiant Aimable Lamp Holders are UL and CUL listed, Class 1 System, suitable for installation in any locale. (patents pending)
❍ RAD 301
MR8/MR11 Locking Swivel Lamp Holder
20 watt (max) MR8 or MR11 lamps
Festoon fixture only
(see page 18 for details)
❍ RAD 302
ALR Locking Swivel Lamp Holder
20 watt (max)
Festoon fixture only
(see page 18 for details)
❍ RAD 303
Halogen Insert Lamp Holder (not shown)
10 watt or 20 watt (max)
Exclusive tempered glass surround
Festoon fixture only
Miscellaneous
Down to the smallest details, Radiant Low Voltage Light Strips are designed with the application in mind. (patents pending)
Dead End Termination (4 count)
No tools are required for termination of field cut pieces
(see page 31 for details)
❍ RAD 402
Mounting Clip (4 count)
Secures strip to surface
Exclusive slot allows for extra easy installation
(see page 31 for details)
❍ RAD 403
Right Angle Bracket (4 count)
Useful for curves and compound curves
(see page 31 for details)
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
Radiant Accessories
❍ RAD 401
•
www.radiantlighting.com
33
LAMP SPECIFICATIONS
RAD LV225 FESTOON FIXTURE
FESTOON TECHNICAL INFORMATION
# LAMPS/
F00T
WATTS
WATTS/
FOOT
VOLTS
10W 12V Xenon Clear Festoon
5.5
10
55.0
12
4.60
5
FT 1210 X F
10W 12V Xenon Frost Festoon
5.5
10
55.0
12
4.60
5
FT 1210
10W 12V Incandescent Clear Festoon
5.5
10
55.0
12
4.60
5
FT 1205 X
5W 12V Xenon Clear Festoon
5.5
5
27.5
12
2.30
11
FT 1205 X F
5W 12V Xenon Frost Festoon
5.5
5
27.5
12
2.30
11
FT 1205
5W 12V Incandescent Clear Festoon
5.5
5
27.5
12
2.30
11
FT 1205 F
5W 12V Incandescent Frost Festoon
5.5
5
27.5
12
2.30
11
FT 2410 X
10W 24V Xenon Clear Festoon
5.5
10
55.0
24
2.30
11
FT 2410 X F
10W 24V Xenon Frost Festoon
5.5
10
55.0
24
2.30
11
FT 2410
10W 24V Incandescent Clear Festoon
5.5
10
55.0
24
2.30
11
FT 2405 X
5W 24V Xenon Clear Festoon
5.5
5
27.5
24
1.20
22
FT 2405 X F
5W 24V Xenon Frost Festoon
5.5
5
27.5
24
1.20
22
FT 2405
5W 24V Incandescent Clear Festoon
5.5
5
27.5
24
1.20
22
FT 2405 F
5W 24V Incandescent Frost Festoon
5.5
5
27.5
24
1.20
22
FT 2403 X
3W 24V Xenon Clear Festoon
5.5
3
16.5
24
1.00
36
FT 2403 X F
3W 24V Xenon Frost Festoon
5.5
3
16.5
24
1.00
36
FT 2403
3W 24V Incandescent Clear Festoon
5.5
3
16.5
24
1.00
36
FT 2403 R
3W 24V Incandescent Red
5.5
3
16.5
24
1.00
36
FT 2403 G
3W 24V Incandescent Green
5.5
3
16.5
24
1.00
36
FT 2403 B
3W 24V Incandescent Blue
5.5
3
16.5
24
1.00
36
FT 2403 Y
3W 24V Incandescent Yellow
5.5
3
16.5
24
1.00
36
# LAMPS/
F00T
WATTS
WATTS/
FOOT
VOLTS
FIXTURE
DESCRIPTION
FT 1210 X
AMPS/
FOOT
FEET/
25 AMPS
RAD LV225 RIGID LOOP FIXTURE
Lamp Specifications
RIGID LOOP TECHNICAL INFORMATION
34
AMPS/
FOOT
FEET/
25 AMPS
FIXTURE
DESCRIPTION
RLB 1210
10W 12V Xenon Clear Rigid Loop
5.5
10
55.0
12
4.58
5
RLB 1210 F
10W 12V Xenon Frost Rigid Loop
5.5
10
55.0
12
4.58
5
RLB 1205
5W 12V Xenon Clear Rigid Loop
5.5
5
27.5
12
2.29
11
RLB 1205 F
5W 12V Xenon Frost Rigid Loop)
5.5
5
27.5
12
2.29
11
RLB 2410
10W 24V Xenon Clear Rigid Loop
5.5
10
55.0
24
2.29
11
RLB 2410 F
10W 24V Xenon Frost Rigid Loop
5.5
10
55.0
24
2.29
11
RLB 2405
5W 24V Xenon Clear Rigid Loop
5.5
5
27.5
24
1.15
22
RLB 2405 F
5W 24V Xenon Frost Rigid Loop
5.5
5
27.5
24
1.15
22
LAMP SPECIFICATIONS
Before a new lamp design is proposed for an application, a thorough search should be made of available lamp types to determine
whether an existing lamp can be rerated to meet user needs. Reviewing lamp specifications in this section can help determine
whether an existing lamp will meet specific needs or, if not, which rerated lamps will satisfy user requirements. The three basic
formulas that apply to rerating incandescent lamps are:
RERATED M.S.C.P =
[ ] X
V
V1
3.5
RERATED current =
M.S.C.P. AT
DESIGN VOLTS
[ ] X
.55
V
V1
RERATED life =
CURRENT AT
DESIGN VOLTS
V = APPLICATION VOLTAGE
[ ] X
12
V1
V
LIFE AT
DESIGN VOLTS
V1 = DESIGN VOLTAGE
2x
20x
LIFE
ER
9x
L
ND
CURRENT & M.S.C.P.
(Multiplying Factor)
CA
8x
AVERAGE LIFE
(Multiplying Factor)
1.5x
OW
EP
10x
7x
6x
5x
1.3x
4x
3x
1.15x
2x
CURRENT
1.0x-100%
.9x
1.0x-100%
.9x
.8x
.7x
CURRENT
.8x
.6x
.5x
.7x
.4x
.6x
.2x
ER
.4x
.1x
PO
W
LIFE
.09x
LE
.08x
.07x
AN
D
.3x
AVERAGE LIFE
(Multiplying Factor)
CURRENT & M.S.C.P.
(Multiplying Factor)
.3x
.5x
C
.06x
.05x
.04x
.03x
.2x
60
70
80
90
100
110
120
130
140
PERCENT RATIO OF DESIGN VOLTS
This graph illustrates the manner in which current, candlepower and life performance vary with percent
changes in applied voltage. These values are typical for miniature and subminiature lamps.
Average life hours are based on rated voltage, 60 cycle alternating current in a room temperature ambient
environment, under static conditions. Dimmed halogen cycle lamps require periodic operation at design voltage
to avoid blackening and reduced life.
CONVERTING BRIGHTNESS VALUES
Mean Spherical Candle Power (M.S.C.P.) is convertible to lumens by a factor of 4 π.
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
Lamp Specifications
LIFE
35
JUST A WORD ABOUT POWER SUPPLIES . . .
Belfer Group works closely with premium electronic and magnetic transformer manufacturers to select and test
quality transformers and components in order to assure the most reliable fixture operation. To assist the Specifier
in choosing the proper Power Supply for their application, we offer these descriptions of the different types of
Power Supplies and the protection and safety devices utilized with our low voltage systems.
MAGNETIC POWER SUPPLIES:
Specifically engineered to handle the rigors of larger applications, Belfer Group Magnetic Power Supplies incorporate a range of
technical features designed to provide consistent power for years of quiet, trouble-free performance. All Belfer Group Magnetic
Power Supplies are engineered around ferrite cores and copper coils 25% larger than standard commercial transformers of
identical power rating, a feature critical in minimizing voltage drop. These oversized components allow our Power Supplies to
run cooler and quieter than cheaper alternatives, an important consideration where noise and/or dimming is of concern. All
Belfer Group Magnetic Power Supplies are full range dimmable, and each is equipped with heavy duty, UL/NEC compliant,
resettable overcurrent/short circuit protection devices to protect each 25 Amp secondary (output) circuit.
ELECTRONIC POWER SUPPLIES:
Perfect for smaller installations, our standard Electronic Power Supplies carry a Class A sound rating and offer a range of
professional grade features. All Belfer Group Electronic Power Supplies are equipped with integral short circuit, overcurrent and
thermal protection. The 60 and 75 watt units have switched resets, while the 150 and 300 watt units are auto-resetting. All
Belfer Group Electronic Power Supplies are full range dimmable and feature Soft-Start circuitry for extended lamp life and
added technical aesthetic.
QTRAN™ POWER SUPPLIES:
Many Specifiers rely upon the quality and performance of QTran Power Supplies for their low voltage lighting projects. Belfer
Group is pleased to offer an extensive range of QTran equipment, specifically designed and selected for compatibility with our
low voltage lighting fixtures. Please consult our sales department for additional information regarding the features and options
available with these units.
REMOTE LOAD CENTERS:
Radiant Linear Low Voltage lighting fixtures are UL and CUL listed, Class 1 systems. Our exclusive Remote Load Centers provide
the required overcurrent protection necessary to maintain these safety listings and overall system integrity in installations
where properly sized transformers are supplied by others.
Power Supplies
DIMMING:
All Belfer Group Power Supplies are suitable for use in applications which require dimming. Electronic Power Supplies are 100%
compatible with trailing edge (reverse phase control, FET type) electronic dimming equipment. Magnetic Power Supplies are
100% compatible with dimming equipment designed to operate inductive loads. Lutron™ dimming is recommended, as are
similar systems from other specification grade dimming manufacturers.
36
POWER SUPPLY WARRANTIES:
At Belfer Group, we use only the best grade of power components from top rated manufacturers. All Belfer Group Power
Supplies are protected from defects in materials and workmanship by our factory warranty for a period of one year. The primary
component manufacturers afford additional warranty protection, pro rata, for periods of up to five years. These warranties are
passed through to our customers. QTran Power Supplies are warranted by QTran for up to five years. There are varying terms
and conditions that may apply to your specific installation. Copies of the Belfer Group warranty, and those of QTran and other
primary component manufacturers, are available upon request.
POWER SUPPLIES
POWER SUPPLY
WATTAGE
VOLTAGE
CIRCUITS /AMP
Magnetic Power Supplies
❍ RPM300-12
300
12
1/25A
❍ RPM600-12
600
12
2/25A
❍ RPM600-24
❍ RPM1200-24
600
24
1/25A
1200
24
2/25A
75
12
1/6A
150
12
1/12.5A
300
12
1/25A
75
24
1/3A
150
24
1/6A
300
24
1/12.5A
150
12/24
1
300
12/24
1
450
12/24
1
450
12/24
2
600
12/24
1
600
12/24
2
750
12/24
1
750
12/24
2
1200
12/24
2
Electronic Power Supplies
❍ RPE75-12
❍ RPE150-12
❍ RPE300-12
❍ RPE75-24
❍ RPE150-24
❍ RPE300-24
QTran™ Magnetic Power Supplies (with circuit breaker and choke)
❍ QX150-1/15-CK-S
❍ QX300-1/25-CK-S
❍ QX450-1/25-CK-L
❍ QX450-2/25-CK-L
❍ QX600-1/25-CK-L
❍ QX600-2/25-CK-L
❍ QX750-1 CT-CK-L
❍ QX750-2 CT-CK-L
❍ QZ1200-2 CT-CK-L
RPM
RPE
QTran
RLC
Radiant Low Voltage Power Supplies are U.L. Listed and designed with 25 Amp overcurrent protection per circuit to be in
compliance with N.E.C. 411. Radiant Low Voltage Lighting Systems can be supplied with QTran™ power supplies as
specified. Other power supply configurations can be designed to meet your specific requirements. Please consult factory.
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
Power Supplies
Remote Load Centers (required if transformers are supplied by others)
RLC-1
BGI Remote Load Center-1 Circuit Breaker, 25A
RLC-2
BGI Remote Load Center - 2 Circuit Breaker, 25A
37
POWER SUPPLIES
MAXIMUM FEET PER TRANSFORMER
10
10 Watt
Watt 5 Watt
5 Watt3 Watt
3 Watt
Item
Description
Watts
per Xfmr
Max. Feet
per Xfmr
55.0 w/ft
Max. Feet
per Xfmr
27.5 w/ft
Max. Feet
per Xfmr
16.5 w/ft
12 volt magnetic power supplies
RPM300-12
RPM600-12
Belfer Group Magnetic 300W 12V - 1 C.B.
Belfer Group Magnetic 600W 12V - 2 C.B.
300
600
5
10
10
21
18
36
600
1200
10
21
21
43
36
72
75
150
300
1
2
5
2
5
10
4
9
18
75
150
300
1
2
5
2
5
10
4
9
18
9
18
27
27
36
36
45
45
72
5
10
16
16
21
21
27
27
43
2
5
8
8
10
10
13
13
21
24 volt magnetic power supplies
RPM600-24
RPM1200-24
Belfer Group Magnetic 600W 24V - 1 C.B.
Belfer Group Magnetic 1200W 24V - 2 C.B.
12 volt electronic power supplies
RPE75-12
RPE150-12
RPE300-12
Belfer Group Electronic 75W 12V
Belfer Group Electronic 150W 12V
Belfer Group Electronic 300W 12V
24 volt electronic power supplies
RPE75-24
RPE150-24
RPE300-24
Belfer Group Electronic 75W 24V
Belfer Group Electronic 150W 24V
Belfer Group Electronic 300W 24V
12/24 volt QTran™ magnetic power supplies (with circuit breaker & choke)
Power Supplies
QX150-1/15-CK-S
QX300-1/25-CK-S
QX450-1/25-CK-L
QX450-2/25-CK-L
QX600-1/25-CK-L
QX600-2/25-CK-L
QX750-1 CT-CK-L
QX750-2 CT-CK-L
QZ1200-2 CT-CK-L
38
QTRAN Magnetic 150W 12/24V - 1 C.B.
QTRAN Magnetic 300W 12/24V - 1 C.B.
QTRAN Magnetic 450W 12/24V - 1 C.B.
QTRAN Magnetic 450W 12/24V - 2 C.B.
QTRAN Magnetic 600W 12/24V - 1 C.B.
QTRAN Magnetic 600W 12/24V - 2 C.B.
QTRAN Magnetic 750W 12/24V - 1 C.B.
QTRAN Magnetic 750W 12/24V - 2 C.B.
QTRAN Magnetic 1200W 12/24V - 2 C.B.
150
300
450
450
600
600
750
750
1200
POWER SUPPLIES
TRANSFORMERS PER STRIP
Feet/
Strip
Lamps/
Strip
Watts/
Strip
Magnetic
Transformer
Electronic
Transformer
QTran
Transformer
11
22
27
33
44
55
110
220
270
330
440
550
300W
300W
300W
600W
600W
600W
150W
300W
300W
n/a
n/a
n/a
150W
300W
300W
450W
450W
600W
11
22
27
33
44
55
55
110
135
165
220
275
300W
300W
300W
300W
300W
300W
75W
150W
150W
300W
300W
300W
150W
150W
150W
300W
300W
300W
11
22
27
33
44
55
33
66
81
99
132
165
300W
300W
300W
300W
300W
300W
75W
75W
150W
150W
150W
300W
150W
150W
150W
150W
150W
300W
10 watt lamps
2’
4’
5’
6’
8’
10’
5 watt lamps
2’
4’
5’
6’
8’
10’
2’
4’
5’
6’
8’
10’
Power Supplies
3 watt lamps
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
39
FIELD MODIFICATIONS
HOW TO CUT TO LENGTH TO FIT EXACT JOB REQUIREMENTS
THERE ARE TWO TYPES OF FIELD MODIFICATIONS:
1. DEAD END OR SINGLE CIRCUIT TERMINATION
The most common modification - end of run conditions where no additional strips are required
You will need:
• Measuring tape
• Hacksaw or wire cutters
• RAD 401 Dead End Termination
1. Remove excess lamps
2. Cut fixture with wire cutters or hacksaw flush to desired length, less 1/4”
3. Attach RAD 401 Dead End Termination to end of fixture
RAD 401
DEAD END
TERMINATION
2. LIVE END OR TWO CIRCUIT CONNECTION
Where attaching an additional LV225 strip or where you need to access the second 25 Amp circuit
You will need:
• Measuring tape
• Hacksaw
• Wire Cutters
• Drill with 1/8” drill bit
• #2 Phillips head screwdriver
Rigid Loop 12 Volt, 10 Watt
1. Remove lamps and lampholders at each end of the strip and at the cut
2. Unscrew and remove Vertical Connector Assemblies from both ends of the strip
3. Pull wire sets 4” out from uncut end
4. Cut fixture with hacksaw flush to desired length
5. Using Vertical Connector Assembly as a template, mark the cut end of the strip for connector
mounting screw and drill 1/8” hole on the mark
6. Install Vertical Connector Assembly to cut end
7. Push wire sets completely into cut end, seating fully into the Vertical Connector Assembly
(wire sets will become visible through the slots in the Vertical Connector Assembly)
8. At uncut end, trim wires to length – 1/2” top, 1” bottom
9. Reinstall Vertical Connector Assembly to the uncut end with screw
40
WIRE SETS
INTEGRATED CONNECTOR
ASSEMBLY
CIRCUIT CALCULATOR CHART
HOW TO DETERMINE THE NUMBER OF 25 AMP CIRCUITS
CIRCUIT CALCULATOR
THE RADIANT CHECKSUM SYSTEM (shown on page 6-7) can also be utilized using our Circuit Calculator Chart.
To use, round the linear footage (or meters) up to the closest mark in the chart, select the lamp wattage specified and follow the columns
to determine the number of 25 Amp circuits.
CALCULATOR
NUMBER OF 25 AMP CIRCUITS
LINEAR FEET
24 VOLT SYSTEM
LENGTH
10 Watt
5 watt
3 Watt
5' 10' 15' 20' 25' 30' 35' 40' 45' 50' 55' 60' 65' 70' 75' 80' 85' 90' 95' 100'
1 1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9 10
1 1
1
1
1
2
2
2
2
3
3
3
4
4
4
4
5
5
5
5
1 1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3
3
NUMBER OF 25 AMP CIRCUITS
LINEAR FEET
12 VOLT SYSTEM
LENGTH
10 Watt
5 watt
10 Watt
5 watt
3 Watt
NUMBER OF 25 AMP CIRCUITS
LINEAR METERS
5m 10m
1 1
1 1
1 1
15m
1
1
1
LENGTH
20m
2
1
1
25m
2
1
1
30m
2
1
1
35m
3
2
1
40m
3
2
1
45m
3
2
1
50m
4
2
1
55m
4
2
2
60m
4
2
2
65m
5
3
2
70m
5
3
2
CHECKSUM = 30
75m
5
3
2
NUMBER OF 25 AMP CIRCUITS
LINEAR METERS
12 VOLT SYSTEM
10 Watt
5 watt
CHECKSUM = 50
5' 10' 15' 20' 25' 30' 35' 40' 45' 50' 55' 60' 65' 70' 75' 80' 85' 90' 95' 100'
1 2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20
1 1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9 10
24 VOLT SYSTEM
LENGTH
CHECKSUM = 100
80m
6
3
2
85m
6
3
2
90m
6
3
2
95m100m
7
7
4
4
2
2
CHECKSUM = 15
5m 10m 15m 20m 25m 30m 35m 40m 45m 50m 55m 60m 65m 70m 75m 80m 85m 90m 95m100m
2 2
2
4
4
6
6
8
8
10 10 12 12 14 14 16 16 18 18 20
1 1
1
2
2
3
3
4
4
5 5
6
6
7
7
8
8
8
8 10
FIXTURE
NOMINAL LENGTH
ACTUAL LENGTH
RAD LV225 F/L 02
2ft fixture
27.1" (690mm)
RAD LV225 F/L 04
4ft fixture
48.7" (1240mm)
RAD LV225 F/L 05
5ft fixture
61.7" (1570mm)
RAD LV225 F/L 06
6ft fixture
74.7" (1900mm)
RAD LV225 F/L 08
8ft fixture
96.4" (2450mm)
RAD LV225 F/L 10
10ft fixture
122.4" (3110mm)
LIGHTING
•
Tel: 732.695.0144
•
Fax: 732.695.0145
•
www.radiantlighting.com
Festoon 24 Volt, 10 Watt
RAD LV 225 ACTUAL LENGTHS
41
P.O. BOX 2088
OCEAN, NEW JERSEY 07712
PH: (732) 695.0144 • FX: (732) 695.0145
www.radiantlighting.com
a
company
© 2003 Radiant. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement