ATEN | CS-128A | User manual | ATEN CS-128A User manual

4 Console / 8 Port
KVM Switch
CS428
User Manual
www.aten.com
CS428 User Manual
FCC Information
This is an FCC Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
RoHS
This product is RoHS compliant.
SJ/T 11364-2006
The following contains information that relates to China.
ii
CS428 User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
Š International – http://support.aten.com
Š North America – http://www.aten-usa.com/product_registration
Telephone Support
Š International – 886-2-8692-6959
Š North America – 1-888-999-ATEN
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed `as is'.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
iii
CS428 User Manual
Package Contents
The basic CS428 package consists of:
Š 1 CS428 KVM Switch
Š 2 KVM Cable Sets (2L-1701S)
Š 1 Power Adapter
Š 1 Rack Mount Kit
Š 1 User Manual*
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
* Features may have been added to the CS428 since this manual was printed.
Please visit our website to download the most up to date version of the
manual.
© Copyright 2008 ATEN® International Co., Ltd.
Manual Part No. PAPE-0167-300G
Manual Date: 2008-08-25
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
iv
CS428 User Manual
Contents
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
1. Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Hardware Setup
Stacking and Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Single Station Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cascaded Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. Basic Operation
Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Port Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
v
CS428 User Manual
4. OSD Operation
OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
OSD Main Menu Headings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
F1 HELP:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
F2 EDIT: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
F3 LIST: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
F4 SCAN: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
F5 ADM: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
F6 Set:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
F7 QV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
F8 Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5. Appendix
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Master View - Computer Connection Tables . . . . . . . . . . . . . . . . . . . . . . 29
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
OSD Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Power On Self Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
vi
CS428 User Manual
About this Manual
This User Manual is provided to help you get the most from your c/c system.
It covers all aspects of installation, configuration and operation. An overview
of the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the CS428 system. Its purpose,
features and benefits are presented, and its front and back panel components
are described.
Chapter 2, Hardware Setup, describes how to set up your installation. The
necessary steps – from a basic single stage hookup to a complete 32 switch
cascaded operation are provided.
Chapter 3, Basic Operation, explains the fundamental concepts involved
in operating the CS428.
Chapter 4, OSD Operation, provides a complete description of the
CS428's OSD (On Screen Display), and how to work with it.
An Appendix, provides specifications and other technical information
regarding the CS428.
vii
CS428 User Manual
Conventions
This manual uses the following conventions:
Monospaced
Indicates text that you should key in.
[]
Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1.
Numbered lists represent procedures with sequential steps.
♦
Bullet lists provide information, but do not involve sequential steps.
→
Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start → Run means to
open the Start menu, and then select Run.
Indicates critical information.
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller.Visit ATEN on the Web for a list of locations and telephone numbers
Š International – http://www.aten.com
Š North America – http://www.aten-usa.com
viii
Chapter 1
Introduction
Overview
The CS-428 KVM Switch is a control unit that allows four independent
keyboard, mouse, and monitor Consoles to access eight computers, either
independently or on a multiuser shared basis, in a convenient, cost effective
manner. A Master View CS-428 unit can control up to 8 PCs. Since it can be
cascaded one level down to a CS-138A, CS-9138, CS-128A, or CS-124A, up
to 9 Master View units (the CS-428 plus eight cascaded ones), can control up
to 64 computers from any of the four Consoles.
Setup is fast and easy; plugging cables into their appropriate ports is all that is
entailed. There is no software to configure, so there is no need to get involved
in complex software installation routines or be concerned with incompatibility
problems. Because the CS-428 intercepts keyboard input directly, it works on
any hardware platform and with all operating systems.
The CS-428 provides a convenient OSD (On Screen Display), function that
allows any of the four Consoles to access any computer connected to the
system by means of an on screen, menu driven interface. In addition, a
powerful Quick View Scan feature allows you to auto scan and monitor the
activities of all operating computers on the installation one by one.
For security, two level password protection (administrator and user), is
provided in order to prevent unauthorized access to the computers. Responding
to the growing use of audio input/output in the workstation space, the CS-428
has been designed with built in microphone and speaker support, as well.
There is no better way to save time and money than with a Master View CS428 installation. By allowing all the attached computers to be managed from
four separate Consoles, a Master View CS-428 installation: (1) eliminates the
expense of having to purchase a separate keyboard, monitor, and mouse for
each computer; (2) saves all the space those extra components would take up;
(3) saves on energy costs; and (4) eliminates the inconvenience and wasted
effort involved in constantly moving around from one computer to another,
while allowing a single user to access the computers from several different
convenient locations, or up to four users to share them.
1
CS428 User Manual
Features
Š 4 Consoles Control 8 Computers
Š Up to four users can operate up to 64 computers (via cascading to CS138A, CS-9138, CS-128A, or CS-124A) at the same time
Š Each console has its own access control
Š Two level password security (one Administrator; four User passwords)
Š Administrator can access any computer completely independently of the
other users
Š Each User has his own access control list
Š Port selection via OSD (On Screen Display)
Š Auto expansion of the OSD port list for cascaded installations
Š OSD automatically adjusts to resolution changes
Š Hot Pluggable - add or remove any computer without powering off the
switch
Š Auto Scan function provides easy monitoring of all computers
Š Supports 1920 x 1440 resolution; DDC2 (Display Data Channel 2)
Š PS/2 compatible mouse support: Microsoft Intellimouse Pro, Logitech
FirstMouse, FirstMouse+, support*
Š Audio (microphone and speaker) support
Š Special design for easy stacking
Š Rack mountable in 19" (1U) system rack
* PS/2 compatible mouse support is for three button (wheel) mice. The
Logitech Mouse Ware program's Change Device procedure does not
work on Microsoft NT systems.
2
1. Introduction
Requirements
Console
Š A VGA, SVGA, or multisync monitor capable of the highest resolution
that you will be using on any computer in the installation.
If a monitor switches to a computer using a resolution that is higher than
the resolution that the monitor can support, serious damage to the monitor
may result.
Š A PS/2 style mouse
Š A PS/2 style keyboard
Š Microphone and Speakers (Optional)
Computers
The following equipment must be installed on each computer:
Š A VGA, SVGA or multisync card.
Š A 6-pin Mini-DIN (PS/2 style) mouse port.
Š A 6-pin Mini-DIN (PS/2 style) keyboard port with +5V DC on pin 4 and
Ground on pin 3.
Cables
Use of substandard cables may damage the connected devices or degrade
overall performance. For optimum signal integrity and to simplify the layout,
we strongly recommend that you use the following high quality Custom Cable
sets:
Connector Type
Consoles 3 and 4
CS Custom Cable
2L-1701S
PS/2 (6 pin mini-DIN) Keyboard and Mouse Ports
2L-1701P
Cascading to Second Stage Master View
2L-1601P
3
CS428 User Manual
Components
Front Panel
1
2
No.
1
Component
Port LEDs
3
4
Description
The Port LEDs provide status information about their
corresponding Computer Ports. There is one pair of LEDs for
each Port. The one on the left is the On Line LED; the one on
the right is the Selected Port LED:
Š An On Line LED lights ORANGE to indicate that the
computer attached to its corresponding port is up and
running.
Š A Selected LED lights GREEN to indicate that the
computer attached to its corresponding port is the one that
has the KVM focus.
4
2
K/M Reset
Switch
If the keyboard and mouse get stuck and need to be reset,
insert a pointed object in here and push.
3
Sound
Opening
System sounds (beeps, etc.), are emitted from this opening.
4
Power LED
Lights BLUE to indicate that the CS-428 has been turned On
and is receiving power.
1. Introduction
Rear Panel
2
1
3
No.
4
5
6
Component
7
8
Description
1
Power Switch
A rocker switch to power the system on and off.
2
Console 3 and 4
Connectors
Use KVM Cable sets (see Cables, page 3), to connect the
components that make up Consoles 3 and 4 to these ports.
3
Power Jack
The power adapater cable plugs in here.
4
Console 2
Microphone and
Speaker Jacks
The microphone and speakers belonging to Console 2 plug
in here.
5
Console 2 KVM
Connectors
The keyboard, monitor and mouse belonging to Console 2
plug in here.
6
Console 1
Microphone and
Speaker Jacks
The microphone and speakers belonging to Console 1 plug
in here.
7
Console 1 KVM
Connectors
The keyboard, monitor and mouse belonging to Console 1
plug in here.
8
KVM Port
Section
Use KVM Cable sets (see Cables, page 3), to connect
computers or cascade additional KVM switches (see
Cascaded Installation, page 9) to any available port.
5
CS428 User Manual
This Page Intentionally Left Blank
6
Chapter 2
Hardware Setup
1. Important safety information regarding the placement of this
device is provided on page 25. Please review it before
proceeding.
2. Make sure that power to all the devices you will be connecting
up have been turned off. You must unplug the power cords of
any computers that have the Keyboard Power On function.
Stacking and Mounting
The CS428 can be placed on the desktop or it can be rack mounted, as
described in the sections that follow.
Stacking
The unit comes with the stacking brackets already attached. To stack additional
units, simply line up the brackets on the top and bottom units, then fit the top
unit down onto the bottom unit.
Rack Mounting
The CS428 can be mounted in a 1U system rack. To rack mount the unit, do
the following:
1. Remove the stacking brackets by unscrewing them from the unit, as shown
in the diagram below:
7
CS428 User Manual
2. Use the screws that came with the rack mount kit to screw the mounting
brackets into the sides of the unit, as shown in the diagram below:
3. Slide the unit into the rack and secure it to the rack.
Single Station Installation
The most basic installation is a Single Stage installation, in which no additional
Master Views are cascaded down from the first unit. To set up a single stage
installation, refer to the installation diagram on the following page (the
numbers in the diagram correspond to the numbers of the steps) as you perform
these steps:
1. Plug the keyboard, monitor, mouse microphone and speaker cables for
Consoles 1 and 2 into the console port connectors located on the CS428’s
rear panel. Each port is labeled with an icon to indicate itself.
Note: Use of microphone and speakers is optional.
2. Use the 2L-1701S KVM cable sets included with this package to connect
the components that make up Consoles 3 and 4 to Console ports 3 and 4 on
the rear panel of the CS428 unit.
3. Use 2L-1701S KVM cable sets (see Cables, page 3), to connect any
available KVM port to the keyboard, monitor, and mouse ports of the
computers you are installing.
4. Plug the power adapter into an AC source; plug the power adapter cable
into the 's Power Jack.
5. Turn on the power to the CS428.
8
2. Hardware Setup
Note: When you turn the unit On, it undergoes a Power On Self Test. If
there is a problem, Port LEDs 1 - 4 flash repeatedly according to a
pattern that indicates what the problem is. See see Power On Self
Test, page 31 for details.
6. Plug in the power cords and power On all the computers.
Note: You must turn on the power to the CS428 before turning on the
power to the computers.
2
4
1
3
Cascaded Installation
To control even more computers, up to eight additional Master View switches
can be cascaded from the KVM ports of the CS428. The cascaded Master
Views that connect back to the CS428 (referred to as the First Stage unit), are
considered Second Stage units. As many as 64 computers can be controlled in
a complete two stage installation. A table showing the relation between the
number of computers and the number of Master View units needed to control
them is provided on page 29 in the Appendix.
Note: 1. Only Master View CS-138A, CS-9138, CS-128A, or CS-124A
switches can be used with the CS428;
2. Switches cannot be cascaded beyond the second stage.
9
CS428 User Manual
To set up a two stage installation, do the following:
1. Make sure that power to all the devices you will be connecting up,
including all preexisting devices on the installation, have been turned off
(unplug the power cords of any computers that have the Keyboard Power
On function; unplug the First Stage unit).
2. Use a 2L-1601P KVM Cable set (see Cables, page 3), to connect any
available KVM port on the CS428 (First Stage unit) to the Console Port
connectors of the Second Stage unit.
3. Use KVM Cable sets (see the Cables section of the Second Stage unit's
user manual for details), to connect any available KVM port on the Second
Stage unit to the keyboard, monitor, and mouse ports of the computer you
are installing.
4. Repeat steps 1 - 3 for any other Second Stage units you wish to connect.
5. Plug in the power adapter cable for the First Stage Master View unit's
Power Jack.
6. For each Second Stage unit, plug the power adapter into an AC source;
plug the power adapter cable into the Master View's Power Jack.
7. Power on the First Stage CS428.
8. Power on all Second Stage units
9. Plug in the power cords and power On all the computers.
Note: You must follow the sequence in steps 5 - 9 when powering up.
8
10
7
6
5
4
3
2
1
Chapter 3
Basic Operation
Hot Plugging
The Master View CS428 supports hot plugging - components can be removed
and added back into the installation by unplugging their cables from the KVM
ports without the need to shut the unit down. In order for hot plugging to work
properly, however, these procedures must be followed:
1. When hot plugging cables from the KVM ports the cable must be plugged
back into the same port it was removed from.
2. You may unplug the mouse and plug it back in again (to reset the mouse,
for example), as long as you use the same mouse.
3. If there is no response to mouse and/or keyboard after you plug the mouse
back in, perform a K/M Reset by inserting a thin pointed object into the
Reset receptacle on the unit's front panel and gently pushing.
Powering Off and Restarting
If it becomes necessary to Power Off any of the Master View units, before
starting it back up you must do the following:
1. Shut down all the computers that are attached to the unit, as well as all the
Second Stage Master Views that are cascaded down from it and all the
computers that are connected to the stations that you shut down.
Note: You must unplug the power cords of any computers that have the
Keyboard Power On function that are connected to the shut down
Master Views. Otherwise, the switches will still receive power from
the computers.
2. Wait 10 seconds, then restart the CS428.
Note: When the CS428 comes up it issues a long beep, and the Consoles
are automatically logged out. Each Console logout produces a short
beep - so you will hear one long and four short beeps.
3. Restart the Second Stage Master Views.
4. After all the Master View's are up, power On the computers.
11
CS428 User Manual
Port Numbering
Each computer on the installation is assigned a unique Port Number (PN). The
PN is a one or two segment number that is determined by the Stage Level and
KVM port of the KVM switch that the computer is connected to. The first
segment represents the KVM Port number of the First Stage unit (the CS428);
the second segment represents the KVM Port number of the Second Stage unit.
Note: The KVM port numbers are clearly indicated on the back panels of the
switches.
For example, a computer connected to KVM port 7 of a First Stage CS428,
would have a PN of 7.
A computer connected to a Second Stage cascaded Master View has a two digit
PN:
Š The first digit represents the KVM Port of the First Stage Master View (the
CS428) that the Second Stage Master View is cascaded down from
Š The second digit represents the KVM Port of the Second Stage unit that
the computer is connected to.
For example. a computer with a PN of 2-3 would be connected to KVM Port 3
of a Second Stage unit; which is cascaded down from KVM Port 2 of the
CS428.
Port Selection
Instant access to any computer on the installation is provided by the menu
driven On Screen Display (OSD) function. OSD operation is discussed in the
next chapter.
12
Chapter 4
OSD Operation
OSD Overview
On Screen Display (OSD), provides a menu driven interface to handle the
computer switching procedure. All operations start from the OSD Main Menu.
To activate the Main Menu, tap either Ctrl key twice.
Note: 1. The keys must be on the same side (both left, or both right).
2. If using the Ctrl key conflicts with applications running on the
computers, you can optionally change the hotkey to the Scroll Lock
key (see OSD Activating Hotkey under the F6 Set function on
page 22), in which case you would press [Scroll Lock] twice.
For security purposes, the OSD incorporates a two level (Administrator / User)
password system. Before the OSD Main Screen comes up, a window appears
that asks you to provide your password. If the password function has been set
for the Console you are at, you must provide the password in order to access
the OSD Main screen.
If this is the first time that the OSD is being run, or if the password function is
not being used, simply press [Enter]. The OSD Main Screen comes up in
Administrator Mode. In this mode, you have administrator privileges, with
access to all User and Administrator functions, and can set up operations
(including password authorization for the future), as you would like.
13
CS428 User Manual
When you invoke the OSD, a screen similar to the one below appears:
Note: 1. The diagram depicts the Administrator's Main Screen. The User Main
Screen does not show the F2 and F5 function, since they are reserved
for the Administrator and can't be accessed by ordinary Users.
2. The OSD always starts in List view, with the highlight bar at the same
position it was in the last time it was closed.
14
4. OSD Operation
OSD Navigation
Š To dismiss the menu, and deactivate the OSD, Click the X at the upper
right corner of the OSD Window; or press [Esc].
Š To Logout, click F8 or the ZZZ symbol at the top of the Main Screen, or
press [F8].
Š To move up or down through the list one line at a time, Click the Up and
Down Triangle symbols (ST) or use the Up and Down Arrow Keys. If
there are more list entries than there is room for on the Main Screen, the
screen will scroll.
Š To move up or down through the list one screen at a time, Click the Up and
Down Arrow symbols (ÏÐ), or use the [Pg Up] and [Pg Dn] keys. If there
are more list entries than there is room for on the Main Screen, the screen
will scroll.
Š To bring the KVM focus to a port, Double Click it, or move the Highlight
Bar to it then press [Enter].
Note: 1. If you try to access a computer that has been designated as private
(see PRIVATE MODE, page 23), a message appears to inform
you that the Port is in Private Mode. In this case, the screen is
blank, and the port can neither be viewed, nor accessed.
2. If you try to access a computer that is already being accessed by
another Console, a message displays to inform you that the Port
is In Use. The target computer's screen can be viewed, but you
cannot give it any input until the Console that already has control
stops accessing it.
3. In a cascaded installation, if a computer attached to a Second
Stage swtich is already being accessed by another Console, that
computer and all the other computers attached to the same Second
Stage unit are considered to be in use. None of them can be
viewed or accessed from your Console. This is so, because
accessing any one computer attached to a Second Stage unit ties
up the entire CS428 Port that the unit is cascaded down from.
Only after the original Console no longer has access - either
because it relinquishes access, or because the timeout delay (see
SET LOGOUT TIMEOUT, page 21), has been exceeded - can
these computers be controlled from another Console.
Š After executing any action, you automatically go back to the menu one
level above.
15
CS428 User Manual
OSD Main Menu Headings
Heading
PN
Explanation
This column lists the Port Numbers for all the KVM Ports. The simplest
method to access a particular computer (assuming you know which port
it is attached to), is to Double Click it with the Mouse; or to use the
Navigation Keys to move the Highlight Bar to it, then press [Enter] .
Indicates ports that this Console can access. This Console cannot
access ports that do not have this symbol displayed. Permission for a
particular Console to be able to access a port is granted by the
Administrator (see SET ACCESSIBLE PORTS, page 21).
QV
An arrowhead symbol in this column indicates the Port has been
selected for Quick View Scan Mode (see F7 QV, page 24).
PC
A sun symbol in this column indicates that the computer connected to
this Port is powered On, and is On Line.
NAME
If a port has been given a name (see F2 EDIT:, page 17), its name
appears in this column.
OSD Functions
OSD functions are used to configure and control the OSD. For example, you
can: rapidly switch to any port; scan selected ports only; limit the list you wish
to view; designate a port for Quick View scanning; create or edit a port name;
or make OSD setting adjustments.
To access an OSD function:
1. Either Click a Function Key field on the screen, or press a Function Key
on the keyboard.
2. In the Submenus that appear make your choice either by Double Clicking
it, or moving the Highlight Bar to it.
3. Press [Esc] to activate your choice and return to the previous menu level.
F1 HELP:
Help provides a quick guide to OSD operation. To return to the OSD Main
Menu, Click the X at the upper right corner of the OSD Window; or press
[Esc].
16
4. OSD Operation
F2 EDIT:
This is an Administrator function. To help remember which computer is
attached to a particular port, every port can be given a name. The Edit function
allows the Administrator to create, modify, or delete port names. To Edit a port
name:
1. Click the port you want, or use the Navigation Keys to move the highlight
bar to it.
2. Click the F2 field, or Press [F2].
3. Key in the new Port Name, or modify/delete the old one.
The maximum number of characters allowed for the Port Name is 15.
Legal characters include:
Š All alpha characters: a - z; A - Z
Š All numeric characters: 0 - 9
Š +, –, /, ., and [Space]
Case does not matter; OSD displays the Port Name in all capitals no matter
how they were keyed in.
4. When you have finished editing, press [Enter] to have the change take
effect. To abort the change, press [Esc].
17
CS428 User Manual
F3 LIST:
This function lets you broaden or narrow the scope of which ports the OSD
lists. This will be different for each Console, depending on the choices made
for that Console. The choices and their meanings are given in the table, below:
Choice
Meaning
ALL
Lists the Port Numbers and Names (if names have been
specified - see F2 EDIT:, page 17), of all the ports on the
installation.
QVIEW
Lists only the ports that have been selected for Quick View
scanning (see F7 QV, page 24).
POWERED ON
Lists only the ports that have their attached computers Powered
On.
POWERED ON +
QVIEW
Lists only the ports that have been selected for Quick View
scanning (see F4 SCAN:, page 19), and that have their
attached computers Powered On.
QVIEW + NAME
Lists only the ports that have been selected for Quick View
scanning (see F7 QV, page 24), and have been assigned
names (see F2 EDIT:, page 17).
NAME
Lists only the ports that have been assigned names (see F2
EDIT:, page 17).
Double Click the choice you want, or move the Highlight Bar to it then press
[Enter]. An icon appears before the choice to indicate that it is the currently
selected one.
Note: 1. You can access any port on any list by Double Clicking it, or using
the Navigation Keys then pressing [Enter].
2. If you select a port that does not have a computer attached to it, or if
the attached computer is powered Off, the OSD will still switch to it,
and will not show an error. To recover, press the OSD Activation
Hotkey (see OSD Overview, page 13).
18
4. OSD Operation
F4 SCAN:
Clicking the F4 field, or pressing [F4] initiates Scan Mode, in which the OSD
cycles through all the ports that have been selected for scanning with the Scan
Mode setting (see SCAN MODE, page 22). When you want to stop at a
particular location, press the [Spacebar] to stop scanning.
Š If the scanning stops on an empty port, or one where the computer is
attached but is powered Off, the monitor screen will be blank and the
mouse and keyboard will have no effect. To recover, To recover, press the
OSD Activation Hotkey.
Š As the OSD cycles through the selected ports, an S appears in front of
each accessed computer's Port ID display to indicate that the computer is
being accessed under Quick View Scanning.
Š If a particular port is being accessed by another Console, an R appears in
front of the Port ID display to indicate that the Port is "View Only." It can
be viewed, but cannot be accessed at this time.
Š If a particular port has been designated as private (see F6, below), a P
appears in front of the Port ID display to indicate that the Port is in
"Private Mode." The screen is blank, and the port can neither be viewed,
nor accessed.
Š If a particular port was accessed by one of the Consoles, but is no longer
being accessed, the OSD begins a Timeout countdown (see Set Access
Timeout and Set Logout Timeout in the table, below), a Z appears in front
of the Port ID display to indicate that the Port is Pending (i.e., the original
Console that accessed it has first priority to reclaim it, but when the
Timeout period ends, it is up for grabs to the first comer).
19
CS428 User Manual
F5 ADM:
F5 allows an Administrator to configure the OSD operation of the Console. To
change a setting Double Click it; or use the Up and Down Arrow Keys to move
the highlight bar to it then press [Enter].
Note: 1. To avoid Administrator conflict, a priority system has been set up in
which, by default, Console 1 has priority over anything attached to
Port 1; Console 2 has priority over anything attached to Port 2;
Console 3 has priority over anything attached to Port 3; and Console
4 has priority over anything attached to Port 4.
2. Only one Administrator may access the F5 ADM (Administrator)
function at a time. If a second Administrator attempts to access the F5
function while it is already being accessed, he is denied access, and a
message appears on screen to inform him of the rejection.
After you select an item, a submenu with further choices for you to select from
appears. Double Click the choice you want, or move the Highlight Bar to then
press [Enter]. An icon appears before the selected choice so that you know
which one it is. The settings are explained in the following table:
Setting
SET PASSWORD
Function
This function is used to set passwords for the Administrator
and User:
1. One Administrator and four User passwords can be set.
2. Move the highlight bar to User or Administrator, then press
[Enter]. A screen that allows you to key in your password
appears. The password may be up to 8 characters long,
and can consist of any combination of letters and numbers
(A - Z, 0 - 9).
3. Key in the new password, then press [Enter]. You are
asked to key the password in again, in order to confirm
that it is correct.
4. Key in the new password again, then press [Enter]. If the
two entries match, the new password is accepted. If the
entries do not match, you must start again from the
beginning.
5. To modify or delete a previous password, use the
backspace key to erase individual letters or numbers.
6. If the Administrator wants to change a User's password,
he must enter his Administrator's password first.
20
4. OSD Operation
Setting
Function
SET ACCESSIBLE
PORTS
This function allows Administrators and Users to select which
Ports can be accessed from a particular Console. Move the
highlight bar to the target computer, then press [Enter] or the
[Spacebar] to toggle access On and Off. If access is On, a
plus mark ( + ) appears to indicate so. If access is Off, the
area is blank. Make your choice, then press [Esc] to confirm.
SET MULTIUSER
MODE
This function determines whether or not the same ID can be
used to log into the CS428 from different Consoles at the
same time.
1. If Disabled, the same ID cannot be used; if Enabled (the
default), the same ID can be used to log in from more than
one Console.
2. If Enabled, the F4, F6, and F7 settings set for any one
Console, will be the same for all other Consoles that log in
with the same ID.
3. Changes made to the F4, F6, and F7 settings by any
logged in Console will automatically affect all Consoles
with the same ID.
SET ACCESS
TIMEOUT
This function is used to set the timeout value to control the
release of access rights to a computer. If the original Console
doesn't access the computer before the timeout value is
reached, the computer becomes available to the other
Consoles. To set the timeout value, key in a number from 2 255 seconds, then press [Enter] (if the number is 0 [zero],
this function is disabled. Default is 010 (ten) seconds.
CLEAR THE NAME
LIST
This function clears the port name list.
RESTORE DEFAULT
VALUES
This function is used to undo all Administrator changes and
return the setup to the original factory default settings - except
for the Names that were assigned to Ports, which are saved.
RELEASE ALL
PRIVATE
Releases all Ports that have been set to Private Mode (see
PRIVATE MODE, page 23), so that they become accessible
to all Consoles.
SET LOGOUT
TIMEOUT
If a Console that has accessed a computer isn't used for the
amount of time set with this function, the Operator is
automatically logged out. A login is necessary before the
Console can be used again. This enables the other Consoles
to gain access to the computers when the original Console is
no longer accessing them, but the Operator has forgotten to
relinquish access. To set the timeout value, key in a number
from 1 - 255 minutes, then press [Enter] If the number is 0
[zero], this function is disabled. Default is 5 (five) minutes.
21
CS428 User Manual
F6 Set:
[F6] allows you to configure the OSD settings for the Console you are working
at. To change a setting:
1. Double Click it; or move the highlight bar to it, then press [Enter]
2. Press [Esc] to activate it.
After you select an item, a submenu with further choices appears. To make a
selection, either Double Click it; or move the Highlight Bar to it, then press
[Enter]. An icon appears before the selected choice to indicate which one it is.
The settings are explained in the table below:
Setting
Function
OSD ACTIVATING
HOTKEY
Selects which Hotkey activates the OSD function: [Ctrl] [Ctrl]
(the default) or [Scroll Lock] [Scroll Lock]. The Scroll Lock
option is provided in case the Ctrl key combination conflicts
with programs running on the computers.
CHANNEL DISPLAY
MODE
Selects how the Port ID is displayed: the Port Number plus
the Name (PN + NAME); the Port Number alone (PN); or the
Name alone (NAME).
CHANNEL DISPLAY
DURATION
Determines how long a Port ID displays for after a port
change has taken place. The choices are: User Defined which lets you select the amount of time that the Port ID
displays for after a port change has taken place (from 1 - 255
sec.); and Display Always On - which displays the Port ID at
all times. If you select User Defined, key in the number of
seconds, then press [Enter]. The default is 3 Seconds.
CHANNEL DISPLAY
POSITION
Allows you to position where the Port ID appears on the screen.
Highlight this item, then press [Enter]; use the Mouse or the
Arrow Keys to position the Port ID display, then Double Click or
press [Enter] to lock the position and return to the Set submenu.
SCAN MODE
Selects which Ports are available for scanning. There are six
choices:
Š ALL - All the Ports which have been set Accessible (F5)
Š QVIEW - Only those Ports which have been set Accessible
(F5) and have been selected for Quick View Scanning (F7)
Š POWERED ON - Only those Ports which have been set
Accessible (F5) and are Powered On
Š POWERED ON + QVIEW - Only those Ports which have
been set Accessible (F5) and have been selected for Quick
View Scanning (F7) and are Powered On
Š QVIEW + NAME - Only those Ports which have been set
Accessible (F5) and have been selected for Quick View
Scanning (F7) and have been named (F2)
Š NAME - Only those Ports which have been set Accessible
(F5) and have been named (F2).
22
4. OSD Operation
(Continued from previous page.)
Setting
Function
SCAN DURATION
Determines how long the display dwells on each port when it
cycles through the selected ports in Quick View Scan Mode.
Key in a value from 1 - 255 seconds, then press [Enter].
Default is 3 seconds.
PRIVATE MODE
The [Enter] key is a toggle that Enables/Disables Private
Mode for the currently selected port. When Private Mode is
Enabled, none of the other Consoles cannot access the port,
and their monitors show a blank screen when they come to it.
If another console tries to access the port, the message:
Private Mode: Console x (where x represents the number of
the console that has set private mode for the port), displays
on its screen.
When you have finished making your selections, press [Esc]
to return to the OSD Main Menu.
RESTORE DEFAULT
VALUES
This function is used to undo all User changes and return the
setup to the original factory default settings - except for the
Names that were assigned to Ports, which are retained.
MOUSE BUTTON
SETUP
This function allows you to set the mouse for right or left
handed operation. Use [Enter] to toggle between the two.
SET PASSWORD
This function is for Users to set their passwords:
1. When you access this function, if you already have a
password you must enter it in order to continue.
2. A screen appears that allows you to key in your new
password. The password may be up to 8 characters long,
and can consist of any combination of letters and numbers
(A - Z, 0 - 9).
3. To modify or delete a previous password, use
[Backspace] to delete the characters.
4. Key in the password, then press [Enter]. You are asked to
key the password in again, in order to confirm that it is
correct. Key in the new password again, then press
[Enter].
If the two entries match, the new password is accepted. If
the entries do not match, you must start again from the
beginning.
23
CS428 User Manual
F7 QV
You can broaden or narrow the number of ports that get automatically scanned
by selecting only the ones you want with the QV (Quick View Scan) function.
[F7] is a toggle that selects or deselects the currently highlighted port for the
Quick View Scanning function (see F4, above). To select/deselect a port for
Quick View Scanning:
1. Double Click the port you want, or use the Navigation Keys to move the
highlight bar to it.
2. Press [F7].
When a port has been selected for Quick View Scanning, an arrowhead
displays in the QV column to indicate so. When a port is deselected, the
arrowhead disappears.
F8 Out
Clicking the F8 field, or pressing [F8] logs you out of OSD control of the
computers, and blanks the Console screen. This is different from simply
pressing [Esc] to deactivate the OSD, since with this function you must log in
all over again to regain access to the OSD.
Note: When you reenter the OSD after logging out, the screen stays blank
except for the OSD Main Menu. You must input your password before
you can continue.
24
Appendix
Safety Instructions
General
Š Read all of these instructions. Save them for future reference.
Š Follow all warnings and instructions marked on the device.
Š Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Š Do not use the device near water.
Š Do not place the device near, or over, radiators or heat registers.
Š The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
Š The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been
provided.
Š Never spill liquid of any kind on the device.
Š Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
Š The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
Š The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug. Always follow your local/national
wiring codes.
Š Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Š If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
25
CS428 User Manual
Š To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
un-interruptible power supply (UPS).
Š Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Š When connecting or disconnecting power to hot-pluggable power
supplies, observe the following guidelines:
Š Install the power supply before connecting the power cable to the
power supply.
Š Unplug the power cable before removing the power supply.
Š If the system has multiple sources of power, disconnect power from the
system by unplugging all power cables from the power supplies.
Š Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Š Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
Š If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
Š The power cord or plug has become damaged or frayed.
Š Liquid has been spilled into the device.
Š The device has been exposed to rain or water.
Š The device has been dropped, or the cabinet has been damaged.
Š The device exhibits a distinct change in performance, indicating a need
for service.
Š The device does not operate normally when the operating instructions
are followed.
Š Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
26
Appendix
Rack Mounting
Š Before working on the rack, make sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Š Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Š Make sure that the rack is level and stable before extending a device from
the rack.
Š Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
Š After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Š Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Š Ensure that proper airflow is provided to devices in the rack.
Š Do not step on or stand on any device when servicing other devices in a
rack.
27
CS428 User Manual
Technical Support
International
Email Support
Email your questions and concerns to:
support@aten.com
Online Support
1. Online technical support is available to ALTUSEN customers through our e-Support Center:
http://support.aten.com
Š Technical Support
Š Troubleshooting
Š Software Updates
2. Online troubleshooting that describes the most commonly encountered problems and offers possible solutions to them; online documentation (including
electronically available manuals); and the latest drivers
and firmware for your product are available at our website: http://www.aten.com
Telephone Support
886-2-8692-6959
Š Documentation
North America
Email Support
Email your questions and concerns to:
support@aten-usa.com
Online Support
1. Online technical support is available to ALTUSEN customers through our e-Support Center:
http://www.aten-usa.com/support
Š Technical Support
Š Troubleshooting
Š Software Updates
2. Online troubleshooting that describes the most commonly encountered problems and offers possible solutions to them; online documentation (including
electronically available manuals); and the latest drivers
and firmware for your product are available at our website: http://www.aten-usa.com
Telephone Support
1-888-999-ATEN
Š Documentation
When you contact us, please have the following information ready beforehand:
Š Product model number, serial number, and date of purchase.
Š Your computer configuration, including operating system, revision level,
expansion cards, and software.
Š Any error messages displayed at the time the error occurred.
Š The sequence of operations that led up to the error.
Š Any other information you feel may be of help.
28
Appendix
Master View - Computer Connection Tables
Switches
Type
Computers
1
CS428
1-8
2
CS-128A / CS-138A / CS-9138
8 - 15
3
CS-128A / CS-138A / CS-9138
15 - 22
4
CS-128A / CS-138A / CS-9138
22 - 29
5
CS-128A / CS-138A / CS-9138
29 - 36
6
CS-128A / CS-138A / CS-9138
36 - 43
7
CS-128A / CS-138A / CS-9138
43 - 50
8
CS-128A / CS-138A / CS-9138
50 - 57
9
CS-128A / CS-138A / CS-9138
57 - 64
Switches
Type
Computers
1
CS428
1-8
2
CS-124A
8 - 11
3
CS-124A
11- 14
4
CS-124A
14 - 17
5
CS-124A
17 - 20
6
CS-124A
20 - 23
7
CS-124A
23 - 26
8
CS-124A
26 - 29
9
CS-124A
29 - 32
29
CS428 User Manual
Specifications
Function
Computer
Connections
Specification
Direct
8
Max
64 (via Cascade)
Port Selection
Connectors
OSD (On Screen Display)
Console 1 & 2
Keyboard
2 x 6-pin Mini DIN Female (Purple)
Video
2 x HDB-15 Female
Mouse
2 x 6-pin Mini DIN Female (Green)
Speaker
Microphone
2 x Mini Stereo Jack Female (Green)
2 x Mini Stereo Jack Female (Pink)
Console 3 & 4
2 x 25-pin D Type Female
KVM Ports
8 x 25-pin D Type Female
Power
1 x DC Jack
Switches
Reset
1 x Semi-recessed Pushbutton
LEDs
On Line
8 (Orange)
Selected
8 (Green)
Power
Emulation
Keyboard
Mouse
1 (Blue)
PS/2 and PC/AT
PS/2 and Serial
Video
1920 x 1440; DDC2
Power Consumption
DC 9V; 7.2W (max.)
Environment
Physical
Properties
Operating Temp.
Storage Temp.
-20 - 60o C
Humidity
0 - 80% RH
Housing
Metal
Weight
4.2 kg
Dimensions (L x W x H)
30
5 - 40o C
43.35 x 25.42 x 4.4 cm (19" / 1U)
Appendix
OSD Factory Default Settings
Setting
Function
MULTIUSER MODE
Enabled
ACCESS TIMEOUT
10 Seconds
OSD HOTKEY
[Ctrl] [Ctrl]
DISPLAY MODE
The Port Number plus the Port Name
DISPLAY DURATION
3 Seconds
SCAN DURATION
3 Seconds
Power On Self Test
When you turn the unit On, it undergoes a Power On Self Test. If there is a
problem, Port LEDs 1 - 4 flash repeatedly according to a pattern that indicates
what the problem is:
Pattern
Indication
On Line LEDs 1 - 8 Flash Simultaneously
Internal RAM Memory Error
On Line LEDs 1 - 8 Flash One After the Other
External RAM Memory Error
On Line LED pairs 1+2, 3+4, 5+6, and 7+8 Flash
One After the Other
ROM Test Error
If any of these problems occur, turn the Switch Off, then turn it On again.
31
CS428 User Manual
Troubleshooting
Symptom
Possible Cause
Action
Keyboard
and/or
Mouse not
responding.
The connection from
the selected port to
the target computer
has been broken, or
the computer is
turned OFF.
Check the Online LED for the selected port. If it is
not lit:
Keyboard/Mouse
need to be reset.
1. Unplug the keyboard and/or Mouse connector
from the Console Keyboard and/or Mouse
Ports, then plug it/them back in.
1. Check to see that the computer is powered On.
2. Check the cables to make sure they are all
properly connected.
2. Use a thin object (such as the end of a paper
clip, or a ballpoint pen), to press the K/M Reset
Switch (located on the front panel), in.
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID
FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK,
OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with
respect to the contents or use of this documentation, and especially disclaims its quality,
performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or
documentation without obligation to notify any individual or entity of such
revisions, or update. For further inquiries, please contact your direct vendor.
32
Index
C
Cables, 3
Components
Front Panel, 4
Rear Panel, 5
Connection Tables, 29
F
Factory Default Settings, 31
Features, 2
H
Hot Plugging, 11
I
Installation
Cascaded, 9
Single Station, 8
L
Limited Warranty, 32
M
Mounting, 7
P
Package Contents, iv
Port Numbering, 12
Port Selection, 12
Power On Self Test, 31
Powering Off and Restarting, 11
R
Rack Mounting, 7
Safety information, 27
Requirements
Cables, 3
Computers, 3
Console, 3
RoHS, ii
S
Safety Instructions
General, 25
Rack Mounting, 27
SJ/T 11364-2006, ii
Specifications, 30
Stacking, 7
System Requirements
Computers, 3
O
Online
Registration, iii
OSD
Factory Default Settings, 31
Functions, 16
Main Menu Headings, 16
Navigation, 15
Overview, 13
Overview, 1
T
Technical Support, 28
Telephone support, iii
Troubleshooting, 32
U
User Notice, iii
33
Download PDF