LM317 3-Terminal Adjustable Regulator 1 Features 3 Description

Add to my manuals
32 Pages

advertisement

LM317 3-Terminal Adjustable Regulator 1 Features 3 Description | Manualzz
Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
LM317 3-Terminal Adjustable Regulator
1 Features
3 Description
•
The LM317 device is an adjustable three-terminal
positive-voltage regulator capable of supplying more
than 1.5 A over an output-voltage range of 1.25 V to
37 V. It requires only two external resistors to set the
output voltage. The device features a typical line
regulation of 0.01% and typical load regulation of
0.1%. It includes current limiting, thermal overload
protection, and safe operating area protection.
Overload protection remains functional even if the
ADJUST terminal is disconnected.
1
•
•
•
•
Output Voltage Range Adjustable
From 1.25 V to 37 V
Output Current Greater Than 1.5 A
Internal Short-Circuit Current Limiting
Thermal Overload Protection
Output Safe-Area Compensation
2 Applications
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ATCA Solutions
DLP: 3D Biometrics, Hyperspectral Imaging,
Optical Networking, and Spectroscopy
DVR and DVS
Desktop PC
Digital Signage and Still Camera
ECG Electrocardiogram
EV HEV Charger: Level 1, 2, and 3
Electronic Shelf Label
Energy Harvesting
Ethernet Switch
Femto Base Station
Fingerprint and Iris Biometrics
HVAC: Heating, Ventilating, and Air Conditioning
High-Speed Data Acquisition and Generation
Hydraulic Valve
IP Phone: Wired and Wireless
Infusion Pump
Intelligent Occupancy Sensing
Motor Control: Brushed DC, Brushless DC, LowVoltage, Permanent Magnet, and Stepper Motor
Point-to-Point Microwave Backhaul
Power Bank Solutions
Power Line Communication Modem
Power Over Ethernet (PoE)
Power Quality Meter
Power Substation Control
Private Branch Exchange (PBX)
Programmable Logic Controller
RFID Reader
Refrigerator
Signal or Waveform Generator
Software Defined Radio (SDR)
Washing Machine: High-End and Low-End
X-ray: Baggage Scanner, Medical, and Dental
Device Information(1)
PART NUMBER
LM317
PACKAGE (PIN)
BODY SIZE (NOM)
SOT (4)
6.50 mm × 3.50 mm
TO-220 (3)
10.16 mm × 8.70 mm
TO-220 (3)
10.16 mm × 8.59 mm
TO-263 (3)
10.18 mm × 8.41 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
4 Battery-Charger Circuit
LM317
VI
INPUT
RS
0.2 W
OUTPUT
ADJUST
R1
240 W
R2
2.4 kW
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Battery-Charger Circuit .........................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
4
7.1
7.2
7.3
7.4
7.5
7.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 8
8.1 Overview ................................................................... 8
8.2 Functional Block Diagram ......................................... 8
8.3 Feature Description................................................... 8
8.4 Device Functional Modes.......................................... 9
9
Application and Implementation ........................ 10
9.1 Application Information............................................ 10
9.2 Typical Application .................................................. 10
9.3 System Examples ................................................... 11
10 Power Supply Recommendations ..................... 17
11 Layout................................................................... 17
11.1 Layout Guidelines ................................................. 17
11.2 Layout Example .................................................... 17
12 Device and Documentation Support ................. 18
12.1 Trademarks ........................................................... 18
12.2 Electrostatic Discharge Caution ............................ 18
12.3 Glossary ................................................................ 18
13 Mechanical, Packaging, and Orderable
Information ........................................................... 18
5 Revision History
Changes from Revision V (February 2013) to Revision W
Page
•
Added Applications, Device Information table, Pin Functions table, ESD Ratings table, Thermal Information table,
Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply
Recommendations section, Layout section, Device and Documentation Support section, and Mechanical,
Packaging, and Orderable Information section. ..................................................................................................................... 1
•
Deleted Ordering Information table. ....................................................................................................................................... 1
2
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
6 Pin Configuration and Functions
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
ADJUST
KCS / KCT (TO-220) PACKAGE
(TOP VIEW)
OUTPUT
KC (TO-220) PACKAGE
(TOP VIEW)
OUTPUT
DCY (SOT-223) PACKAGE
(TOP VIEW)
INPUT
OUTPUT
ADJUST
ADJUST
KTT (TO-263) PACKAGE
(TOP VIEW)
OUTPUT
OUTPUT
KTE PACKAGE
(TOP VIEW)
INPUT
OUTPUT
ADJUST
INPUT
OUTPUT
ADJUST
Pin Functions
PIN
DCY, KCS,
KCT, KTT
TYPE
ADJUST
1
I
Output voltage adjustment pin. Connect to a resistor divider to set VO
INPUT
3
I
Supply input pin
OUTPUT
2
O
Voltage output pin
NAME
DESCRIPTION
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
3
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over virtual junction temperature range (unless otherwise noted) (1)
MIN
VI – VO
Input-to-output differential voltage
TJ
Tstg
(1)
MAX
UNIT
40
V
Operating virtual junction temperature
150
°C
Lead temperature 1,6 mm (1/16 in) from case for 10 s
260
°C
150
°C
Storage temperature range
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
7.2 ESD Ratings
MAX
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins (1)
2500
Charged device model (CDM), per JEDEC specification JESD22-C101,
all pins (2)
1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
MIN
VO
Output voltage
VI – VO
Input-to-output differential voltage
IO
Output current
TJ
Operating virtual junction temperature
MAX
UNIT
1.25
7
V
3
40
V
1.5
A
125
°C
0
7.4 Thermal Information
LM317
THERMAL METRIC
(1)
RθJA
Junction-to-ambient thermal resistance
RθJC(top)
Junction-to-case (top) thermal resistance
RθJC(bot)
Junction-to-case (bottom) thermal resistance
(1)
4
DCY
KCS
KTT
4 PINS
4 PINS
4 PINS
53
19
25.3
30.6
17
18
—
3
1.94
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953).
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
7.5 Electrical Characteristics
over recommended ranges of operating virtual junction temperature (unless otherwise noted)
TEST CONDITIONS (1)
PARAMETER
Line regulation (2)
VI – VO = 3 V to 40 V
CADJ (3) = 10 μF,
TJ = 25°C
Load regulation
IO = 10 mA to 1500 mA
TJ = 0°C to 125°C
Thermal regulation
20-ms pulse,
MIN
TYP
MAX
TJ = 25°C
0.01
0.04
TJ = 0°C to 125°C
0.02
0.07
25
mV
0.1
0.5
%VO
VO ≤ 5 V
VO ≥ 5 V
20
70
mV
VO ≥ 5 V
0.3
1.5
%VO
0.03
0.07
%VO/W
50
100
μA
0.2
5
μA
1.25
1.3
V
TJ = 25°C
Change in
ADJUST terminal current
VI – VO = 2.5 V to 40 V, PD ≤ 20 W, IO = 10 mA to 1500 mA
Reference voltage
VI – VO = 3 V to 40 V, PD ≤ 20 W, IO = 10 mA to 1500 mA
Output-voltage
temperature stability
TJ = 0°C to 125°C
0.7
Minimum load current
to maintain regulation
VI – VO = 40 V
3.5
VI – VO ≤ 15 V,
PD < PMAX (4)
VI – VO ≤ 40 V,
PD < PMAX (4),
RMS output noise voltage
f = 10 Hz to 10 kHz,
(% of VO)
Ripple rejection
VO = 10 V,
Long-term stability
TJ = 25°C
(1)
(2)
(3)
(4)
1.2
TJ = 25°C
1.5
2.2
0.15
0.4
TJ = 25°C
f = 120 Hz
%/V
VO ≤ 5 V
ADJUST terminal current
Maximum output current
UNIT
%VO
10
mA
A
0.003
CADJ = 0 μF
(3)
CADJ = 10 μF (3)
%VO
57
62
dB
64
0.3
1
%/1k hr
Unless otherwise noted, the following test conditions apply: |VI – VO| = 5 V and IOMAX = 1.5 A, TJ = 0°C to 125°C. Pulse testing
techniques are used to maintain the junction temperature as close to the ambient temperature as possible.
Line regulation is expressed here as the percentage change in output voltage per 1-V change at the input.
CADJ is connected between the ADJUST terminal and GND.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA) / θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
5
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
7.6 Typical Characteristics
1.4
10.01
TA = 25°C
TA = –40°C
1.2
10.005
TA = –40°C
1
0.8
10
V OUT – V
V OUT – V
TA = 25°C
9.995
TA = 125°C
0.6
0.4
TA = 125°C
0.2
9.99
0
9.985
-0.2
VOUT = VREF
VOUT = 10 V Nom
-0.4
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
9.98
IOUT – A
IOUT – A
Figure 2. Load Regulation
Figure 1. Load Regulation
11
-1
10.4
-1.5
10.2
10
-3
9.8
-3.5
9.6
-4
-4.5
-2
10
-3
9.8
9.6
9.4
-4
9.4
9.2
-4.5
-68
1.28
-66
1.275
-64
V IN – V
60
70
1.5
1.4
1.3
1.2
1.1
1
0.9
0.8
0.7
V IN = 15 V
V OUT = 10 V
f = 120 Hz
TA = 25°C
0.6
40
35
-50
30
1.24
25
-52
20
1.245
15
-54
10
1.25
5
50
-56
0.5
TA = 125°C
-58
0.4
1.26
-60
0.3
TA = 25°C
0.2
1.265
-62
0
TA = –40°C
0.1
Ripple Rejection – dB
1.285
0
40
Figure 4. Load Transient Response
1.27
V OUT – V
30
Tim e – µs
Figure 3. Load Transient Response
IOUT – A
Figure 5. Line Regulation
6
20
-30
9
Tim e – µs
1.255
9.2
CADJ = 10 µF
-5
70
60
50
40
30
20
0
10
-10
-20
10.2
VOUT
-2.5
9
-30
10.4
-3.5
CADJ = 0 µF
-5
10.6
VIN
0
VOUT
10.8
10
-2
-2.5
11
-10
VIN
Load Current – A
10.6
V OUT Deviation – V
-0.5
-1
-1.5
Load Current – A
0
10.8
-20
0
-0.5
Figure 6. Ripple Rejection
vs Output Current
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
-75
-90
-70
-80
-65
-70
Ripple Rejection – dB
Ripple Rejection – dB
Typical Characteristics (continued)
-60
-55
-50
V IN – V OUT = 15 V
IOUT = 500 m A
f = 120 Hz
TA = 25°C
-45
-40
10
15
CADJ = 0 µF
-60
CADJ = 10 µF
-50
-40
-30
-20
-35
5
V IN = 15 V
V OUT = 10 V
IOUT = 500 m A
TA = 25°C
20
25
30
35
V OUT – V
-10
100
100
1k
1000
10k
10000
100k
100000
1M
1000000
Frequency – Hz
Figure 7. Ripple Rejection
vs Output Voltage
Figure 8. Ripple Rejection
vs Frequency
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
7
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
8 Detailed Description
8.1 Overview
The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5
A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage.
The device features a typical line regulation of 0.01% and typical load regulation of 0.1%. It includes current
limiting, thermal overload protection, and safe operating area protection. Overload protection remains functional
even if the ADJUST terminal is disconnected.
The LM317 device is versatile in its applications, including uses in programmable output regulation and local oncard regulation. Or, by connecting a fixed resistor between the ADJUST and OUTPUT terminals, the LM317
device can function as a precision current regulator. An optional output capacitor can be added to improve
transient response. The ADJUST terminal can be bypassed to achieve very high ripple-rejection ratios, which are
difficult to achieve with standard three-terminal regulators.
8.2 Functional Block Diagram
Input
Iadj
+
1.25 V
Adj.
Over Temp &
Over Current
Protection
Output
8.3 Feature Description
8.3.1 NPN Darlington Output Drive
NPN Darlington output topology provides naturally low output impedance and an output capacitor is optional. To
support maximum current and lowest temperature, 3-V headroom is recommended (VI – VO).
8.3.2 Overload Block
Over-current and over-temperature shutdown protects the device against overload or damage from operating in
excessive heat.
8.3.3 Programmable Feedback
Op amp with 1.25-V offset input at the ADJUST terminal provides easy output voltage or current (not both)
programming. For current regulation applications, a single resistor whose resistance value is 1.25 V/IO and power
rating is greater than (1.25 V)2/R should be used. For voltage regulation applications, two resistors set the output
voltage.
8
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
8.4 Device Functional Modes
8.4.1 Normal Operation
The device OUTPUT pin will source current necessary to make OUTPUT pin 1.25 V greater than ADJUST
terminal to provide output regulation.
8.4.2 Operation With Low Input Voltage
The device requires up to 3-V headroom (VI – VO) to operate in regulation. With less headroom, the device may
drop out and OUTPUT voltage will be INPUT voltage minus drop out voltage.
8.4.3 Operation at Light Loads
The device passes its bias current to the OUTPUT pin. The load or feedback must consume this minimum
current for regulation or the output may be too high.
8.4.4 Operation In Self Protection
When an overload occurs the device will shut down Darlington NPN output stage or reduce the output current to
prevent device damage. The device will automatically reset from the overload. The output may be reduced or
alternate between on and off until the overload is removed.
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
9
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The flexibility of the LM317 allows it to be configured to take on many different functions in DC power
applications.
9.2 Typical Application
D1
1N4002
Input
VI
Output
LM317
R1
240 W
Adjust
Ci
0.1 µF
VO
Vref = 1.25 V
IAdj
D2
1N4002
CO
1.0 µF
CADJ
R2
Figure 9. Adjustable Voltage Regulator
9.2.1 Design Requirements
• R1 and R2 are required to set the output voltage.
• CADJ is recommended to improve ripple rejection. It prevents amplification of the ripple as the output voltage
is adjusted higher.
• Ci is recommended, particularly if the regulator is not in close proximity to the power-supply filter capacitors. A
0.1-µF disc or 1-µF tantalum capacitor provides sufficient bypassing for most applications, especially when
adjustment and output capacitors are used.
• CO improves transient response, but is not needed for stability.
• Protection diode D2 is recommended if CADJ is used. The diode provides a low-impedance discharge path to
prevent the capacitor from discharging into the output of the regulator.
• Protection diode D1 is recommended if CO is used. The diode provides a low-impedance discharge path to
prevent the capacitor from discharging into the output of the regulator.
9.2.2 Detailed Design Procedure
VO is calculated as shown in Equation 1. IADJ is typically 50 µA and negligible in most applications.
VO = VREF (1 + R2 / R1) + (IADJ × R2)
10
(1)
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
Typical Application (continued)
9.2.3 Application Curves
20
10.10
20
10.12
CADJ = 0 µF
10.08
19
18
10.06
18
17
10.04
VOUT
10.10
V IN Change – V
VIN
16
V OUT – V
V IN Change – V
VOUT
10.02
10.08
10.06
17
10.04
VIN
V OUT – V
19
CADJ = 10 µF
16
10.02
10.00
Tim e – µs
65
55
45
35
25
15
5
-5
-15
9.98
-25
65
55
45
35
25
14
15
9.98
5
14
-5
15
-15
10.00
-25
15
Tim e – µs
Figure 10. Line-Transient Response
Figure 11. Line-Transient Response
9.3 System Examples
9.3.1 0-V to 30-V Regulator Circuit
æ
R + R3 ö
VOUT = VREF ç 1 + 2
÷ - 10 V
R1 ø
è
Here, the voltage is determined by
LM317
+35 V
INPUT
OUTPUT
ADJUST
VO
R1
120 W
−10 V
C1
0.1 µF
R3
680 W
R2
3 kW
Figure 12. 0-V to 30-V Regulator Circuit
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
11
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
System Examples (continued)
9.3.2 Adjustable Regulator Circuit With Improved Ripple Rejection
C2 helps to stabilize the voltage at the adjustment pin, which will help reject noise. Diode D1 exists to discharge
C2 in case the output is shorted to ground.
LM317
VI
INPUT
VO
OUTPUT
ADJUST
R1
240 W
D1
1N4002
C1
0.1 µF
C3
1 µF
R2
5 kW
C2
10 µF
Figure 13. Adjustable Regulator Circuit with Improved Ripple Rejection
9.3.3 Precision Current-Limiter Circuit
This application will limit the output current to the ILIMIT in the diagram.
LM317
VI
INPUT
Ilimit
OUTPUT
R1
ADJUST
1.2
R1
Figure 14. Precision Current-Limiter Circuit
9.3.4 Tracking Preregulator Circuit
This application keeps a constant voltage across the second LM317 in the circuit.
R2
720 Ω
ADJUST
INPUT
VI
R1
240 Ω
OUTPUT
LM317
LM317
INPUT
OUTPUT
R3
120 Ω
ADJUST
C1
0.1 µF
VO
C2
1 µF
Output
Adjust
R4
1 kΩ
Figure 15. Tracking Preregulator Circuit
12
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
System Examples (continued)
9.3.5 1.25-V to 20-V Regulator Circuit With Minimum Program Current
Since the value of VREF is constant, the value of R1 determines the amount of current that flows through R1 and
R2. The size of R2 determines the IR drop from ADJUSTMENT to GND. Higher values of R2 translate to higher
VOUT.
LM317
INPUT
VI
OUTPUT
ADJUST
VO
R1
1.2 kΩ
R2
20 kΩ
Figure 16. 1.25-V to 20-V Regulator Circuit With Minimum Program Current
9.3.6 Adjusting Multiple On-Card Regulators With a Single Control
With different values of R1 for each LM317, R2 can be chosen such that each LM317 outputs a different voltage.
LM317
VI
INPUT
LM317
OUTPUT
ADJUST
VO
INPUT
VI
R1
120 W
OUTPUT
LM317
VO
ADJUST
VI
INPUT
OUTPUT
VO
ADJUST
R2
1 kW
Figure 17. Adjusting Multiple On-Card Regulators With a Single Control
9.3.7 Battery-Charger Circuit
The series resistor limits the current output of the LM317, minimizing damage to the battery cell.
LM317
VI
INPUT
RS
0.2 W
OUTPUT
ADJUST
R1
240 W
R2
2.4 kW
Figure 18. Battery-Charger Circuit
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
13
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
System Examples (continued)
9.3.8 50-mA Constant-Current Battery-Charger Circuit
The current limit operation mode can be used to trickle charge a battery at a fixed current. ICHG = 1.25V÷24Ω. VI
should be greater than VBAT + 4.25 V. (1.25V [VREF]+ 3V [headroom])
LM317
VI
INPUT
24 Ω
OUTPUT
ADJUST
Figure 19. 50-mA Constant-Current Battery-Charger Circuit
9.3.9 Slow Turn-On 15-V Regulator Circuit
The capacitor C1, in combination with the PNP transistor, helps the circuit to slowly start supplying voltage. In the
beginning, the capacitor is not charged. Therefore output voltage will start at VC1+ VBE + 1.25V = 0V + 0.65V +
1.25V = 1.9V. As the capacitor voltage rises, VOUT will as rise at the same rate. When the output voltage reaches
the value determined by R1 and R2, the PNP will be turned off.
LM317
VI
INPUT
OUTPUT
VO = 15 V
R1
240 Ω
ADJUST
D1
1N4002
R3
50 kΩ
R2
2.7 kΩ
2N2905
C1
25 µF
Figure 20. Slow Turn-On 15-V Regulator Circuit
9.3.10 AC Voltage-Regulator Circuit
These two LM317s can regulate both the positive and negative swings of a sinusoidal AC input.
LM317
VI
INPUT
OUTPUT
ADJUST
480 Ω
12 VI(PP)
120 Ω
480 Ω
ADJUST
VI
INPUT
120 Ω
6 VO(PP)
2 W (TYP)
OUTPUT
LM317
Figure 21. AC Voltage-Regulator Circuit
14
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
System Examples (continued)
9.3.11 Current-Limited 6-V Charger Circuit
As the charge current increases, the voltage at the bottom resistor increases until the NPN starts sinking current
from the adjustment pin. The voltage at the adjustment pin will drop, and consequently the output voltage will
decrease until the NPN stops conducting.
LM317
INPUT
VI+
OUTPUT
ADJUST
R1
240 W
R2
1.1 kW
R3
VI−
Figure 22. Current-Limited 6-V Charger Circuit
9.3.12 Adjustable 4-A Regulator Circuit
This application keeps the output current at 4 A while having the ability to adjust the output voltage using the
adjustable (1.5 kΩ in schematic) resistor.
LM317
VI
INPUT
0.2 Ω
OUTPUT
ADJUST
LM317
INPUT
0.2 Ω
OUTPUT
ADJUST
4.5 V to 25 V
LM317
INPUT
0.2 Ω
OUTPUT
ADJUST
5 kΩ
100 Ω
TL080
+
2N2905
5 kΩ
_
150 Ω
200 pF
1.5 kΩ
Figure 23. Adjustable 4-A Regulator Circuit
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
15
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
System Examples (continued)
9.3.13 High-Current Adjustable Regulator Circuit
The NPNs at the top of the schematic allow higher currents at VOUT than the LM317 can provide, while still
keeping the output voltage at levels determined by the adjustment pin resistor divider of the LM317.
TIP73
2N2905
VI
500 W
5 kW
22 W
LM317
INPUT
VO
OUTPUT
ADJUST
120 W
1N4002
10 µF
47 µF
10 µF
Figure 24. High-Current Adjustable Regulator Circuit
16
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
LM317
www.ti.com
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
10 Power Supply Recommendations
The LM317 is designed to operate from an input voltage supply range between 1.25 V to 37 V greater than the
output voltage. If the device is more than six inches from the input filter capacitors, an input bypass capacitor, 0.1
μF or greater, of any type is needed for stability.
11 Layout
11.1 Layout Guidelines
•
•
•
It is recommended that the input terminal be bypassed to ground with a bypass capacitor.
The optimum placement is closest to the input terminal of the device and the system GND. Care must be
taken to minimize the loop area formed by the bypass-capacitor connection, the input terminal, and the
system GND.
For operation at full rated load, it is recommended to use wide trace lengths to eliminate I × R drop and heat
dissipation.
11.2 Layout Example
OUTPUT
Ground
COUT
R2
Power
INPUT
OUTPUT
R1
ADJ/GND
Cadj
High
Frequency
Bypass
Capacitor
0.1μF
10μF
High Input
Bypass
Capacitor
Ground
Figure 25. Layout Example
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
17
LM317
SLVS044W – SEPTEMBER 1997 – REVISED OCTOBER 2014
www.ti.com
12 Device and Documentation Support
12.1 Trademarks
All trademarks are the property of their respective owners.
12.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.3 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18
Submit Documentation Feedback
Copyright © 1997–2014, Texas Instruments Incorporated
Product Folder Links: LM317
PACKAGE OPTION ADDENDUM
www.ti.com
7-Mar-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM317DCY
ACTIVE
SOT-223
DCY
4
80
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
0 to 125
L3
LM317DCYG3
ACTIVE
SOT-223
DCY
4
80
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
0 to 125
L3
LM317DCYR
ACTIVE
SOT-223
DCY
4
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
0 to 125
L3
LM317DCYRG3
ACTIVE
SOT-223
DCY
4
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
0 to 125
L3
LM317KC
OBSOLETE
TO-220
KC
3
TBD
Call TI
Call TI
0 to 125
LM317
LM317KCE3
OBSOLETE
TO-220
KC
3
TBD
Call TI
Call TI
0 to 125
LM317
LM317KCS
ACTIVE
TO-220
KCS
3
50
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
0 to 125
LM317
LM317KCSE3
ACTIVE
TO-220
KCS
3
50
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
0 to 125
LM317
LM317KCT
ACTIVE
TO-220
KCT
3
50
Pb-Free
(RoHS)
CU SN
N / A for Pkg Type
0 to 125
LM317
LM317KTER
OBSOLETE
PFM
KTE
3
TBD
Call TI
Call TI
0 to 125
LM317
LM317KTTR
ACTIVE
DDPAK/
TO-263
KTT
3
500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-245C-168 HR
0 to 125
LM317
LM317KTTRG3
ACTIVE
DDPAK/
TO-263
KTT
3
500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-245C-168 HR
0 to 125
LM317
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
7-Mar-2014
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Sep-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
LM317DCYR
SOT-223
DCY
4
2500
330.0
12.4
LM317KTTR
DDPAK/
TO-263
KTT
3
500
330.0
24.4
Pack Materials-Page 1
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
7.05
7.4
1.9
8.0
12.0
Q3
10.8
16.3
5.11
16.0
24.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Sep-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM317DCYR
SOT-223
DCY
4
2500
340.0
340.0
38.0
LM317KTTR
DDPAK/TO-263
KTT
3
500
340.0
340.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
MPDS094A – APRIL 2001 – REVISED JUNE 2002
DCY (R-PDSO-G4)
PLASTIC SMALL-OUTLINE
6,70 (0.264)
6,30 (0.248)
3,10 (0.122)
2,90 (0.114)
4
0,10 (0.004) M
3,70 (0.146)
3,30 (0.130)
7,30 (0.287)
6,70 (0.264)
Gauge Plane
1
2
0,84 (0.033)
0,66 (0.026)
2,30 (0.091)
4,60 (0.181)
1,80 (0.071) MAX
3
0°–10°
0,10 (0.004) M
0,25 (0.010)
0,75 (0.030) MIN
1,70 (0.067)
1,50 (0.059)
0,35 (0.014)
0,23 (0.009)
Seating Plane
0,08 (0.003)
0,10 (0.0040)
0,02 (0.0008)
4202506/B 06/2002
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters (inches).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC TO-261 Variation AA.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPFM001E – OCTOBER 1994 – REVISED JANUARY 2001
KTE (R-PSFM-G3)
PowerFLEX PLASTIC FLANGE-MOUNT
0.375 (9,52)
0.080 (2,03)
0.070 (1,78)
0.365 (9,27)
0.360 (9,14)
0.050 (1,27)
0.040 (1,02)
0.350 (8,89)
0.220 (5,59)
NOM
0.010 (0,25) NOM
Thermal Tab
(See Note C)
0.360 (9,14)
0.350 (8,89)
0.295 (7,49)
NOM
0.320 (8,13)
0.310 (7,87)
0.420 (10,67)
0.410 (10,41)
1
3
0.025 (0,63)
0.031 (0,79)
0.100 (2,54)
Seating Plane
0.004 (0,10)
0.010 (0,25) M
0.005 (0,13)
0.001 (0,03)
0.200 (5,08)
0.041 (1,04)
0.031 (0,79)
0.010 (0,25)
NOM
Gage Plane
3°– 6°
0.010 (0,25)
4073375/F 12/00
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
The center lead is in electrical contact with the thermal tab.
Dimensions do not include mold protrusions, not to exceed 0.006 (0,15).
Falls within JEDEC MO-169
PowerFLEX is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
PACKAGE OUTLINE
KCS0003B
TO-220 - 19.65 mm max height
SCALE 0.850
TO-220
4.7
4.4
10.36
9.96
1.32
1.22
2.9
2.6
6.5
6.1
8.55
8.15
(6.3)
( 3.84)
12.5
12.1
19.65 MAX
9.25
9.05
3X
3.9 MAX
13.12
12.70
3
1
3X
3X
0.47
0.34
0.90
0.77
2.79
2.59
2X 2.54
1.36
1.23
5.08
4222214/A 10/2015
NOTES:
1. All controlling linear dimensions are in inches. Dimensions in brackets are in millimeters. Any dimension in brackets or parenthesis are for
reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC registration TO-220.
www.ti.com
EXAMPLE BOARD LAYOUT
KCS0003B
TO-220 - 19.65 mm max height
TO-220
0.07 MAX
ALL AROUND
3X
2X (1.7)
METAL
(1.2)
2X SOLDER MASK
OPENING
(1.7)
R (0.05)
SOLDER MASK
OPENING
2
1
(2.54)
3
0.07 MAX
ALL AROUND
(5.08)
LAND PATTERN EXAMPLE
NON-SOLDER MASK DEFINED
SCALE:15X
4222214/A 10/2015
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement