Eureka | 4500 Series | Specifications | Eureka 4500 Series Specifications

Upright Vacuum Cleaner
Household Type
Owner’s Guide
4500 Series
Index
Important Safeguards ........... 2
Service Information ............... 4
Assembly ........................... 5-6
Use ........................................ 7
Thermal Cut Off .............. 4 & 7
Accessories ........................... 8
Brush Roll ............................. 9
Brush Roll Belt ................. 9-10
Dust Bag ........................ 10-11
Hose Blockage ............... 12-13
Filters .................................. 14
HEPA Filter .......................... 14
Light Bulb ............................ 15
Problem Solving .................. 16
Customer Order Form ......... 17
Warranty .............................. 19
IMPORTANT
Do not return this
product to the store.
For assembly problems or
questions contact: Eureka’s
Customer Service Division toll
free at 1-800-282-2886*, 7 a.m.
to 8 p.m., Central Standard
Time, Monday through
Saturday.
For replacement of broken
or missing items to be
shipped direct to you, call
1-800-438-7352*, 8 a.m. to
4:45 p.m., Central Standard
Time, Monday through Friday.
*En Mexico llame 254 23 52.
www.eureka.com
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and
before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service center before using.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do
not run vacuum cleaner over cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that
may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
• Do not place cleaner on furniture or stairs as the brush roll may cause damage. Place cleaner on floor with the handle in
storage position while using attachments.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust bag in place.
• Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive
belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
SAVE THESE INSTRUCTIONS
2
CONSEILS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de blessure:
• Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.
• Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou avant le nettoyage ou l’entretien.
• Ne permettez pas qu’il soit utilisé comme jouet. Une attention particulière est nécessaire lorsque utilisé par ou prés d’un
enfant.
• Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les accessoires recommandés par le fabriquant.
• Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l’aspirateur ne fonctionne pas comme il le devrait, s’il a été
échappé, s’il est endommagé, s’il a été laissé à l’extérieur ou échappé dans l’eau, retournez-le à un centre de service
avant d’utiliser.
• Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de poignée. Ne pas fermer une porte sur
le cordon ou tirer le cordon sur des coins ou bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le
cordon à distance des surfaces chauffantes.
• Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour transporter le courant.
• Fermer tous les contrôles avant de débrancher.
• Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le cordon.
• Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.
• Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquées; assurez-vous qu’elles soient
dégagées de poussière, mousse, cheveux ou toute autre chose qui pourrait réduire le passage de l’air.
• Cet aspirateur créé de la succion et contient un rouleau-brosse tournant. Tenir les parties mobiles et les ouvertures loin
des cheveux, du linge, des doigts et de toute partie du corps.
• Ne pas mettre l’aspirateur sur les meubles ou sur les escaliers car le rouleau-brosse peut faire des dommages. Placer
l’aspirateur sur le plancher avec le manche en entreposage position temps que les accessoires sont en usage.
• Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumettes ou cendres chaudes.
• N’utilisez pas sans le sac de poussière en place.
• Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour prévenir des brûlures, évitez de
touché la poulie du courroie lorsque vous réparez la courroie.
• Portez une attention particulière lorsque vous nettoyez les escaliers.
• Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l’essence: Ne pas utiliser dans les
endroits où ces liquides pourraient être présents.
• Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.
• Maintenez un bon éclairage à l’endroit où vous travaillez.
• Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
3
To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée (une des lames est plus large).
Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un
électricien qualifié. Ne pas modifier la fiche.
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner to prevent
bag tears, hose clogs, and possible motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. For additional service information telephone our toll
free number for the nearest Eureka Authorized Warranty Station. You should know the model, type and serial numbers
when you call:
USA: 1-800-282-2886
Mexico: 254 23 52
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701,
USA. In Canada write to The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited
Warranty for complete service information.
DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.
Rating Plate
The model, type, and serial numbers are indicated on the
rating plate located on the underneath side of the cleaner.
For prompt and complete service information, always refer
to these numbers when inquiring about service.
Model & Type__________________________
MODEL
VOLTS
TYPE
SERIAL NO.
AMPS.
HERTZ
SERVICE INFORMATION: 1-800-282-2886
THE EUREKA COMPANY
BLOOMINGTON, ILLINOIS 61701
Serial No. _____________________________
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly
shuts off, push power switch off and unplug the cleaner. Check the cleaner for a possible source of overheating such as a full
bag, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to
use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the cleaner still does not run,
then take it to a Eureka Authorized Service Center for repair.
4
HOW TO ASSEMBLE
CAUTION: Moving parts, make sure on/off switch is in off position before plugging in.
CAUTION: Assemble the cleaner before using.
NOTE: Features may vary by model yet all parts assemble the same.
Step B Attach Hose
Step A Attach Handle
CAUTION: Do not catch cord under handle.
2
Tab
3
#
Ledge
1
Groove
2
1
Groove
Electrical
Cord
3
1. From rear of cleaner, align handle with groove and slide
onto cleaner. If necessary, use thumb and finger
pressure to slide handle into position.
1. Before placing the front cover on the unit, install the
hose.
2. Locate the tab on the hose adapter (shortest end).
2. Once handle is in place, check that the electrical cord
is not pinched between the unit and the handle. Push
excess cord back into the hole provided in the back of
the handle.
3. Look at the opening on the top of the cleaner and locate
the ledge. The tab on the hose adapter will be under
the ledge in the opening when hose is installed properly.
3. Attach handle with two 5/8 inch screws in the assembly
packet. Use a Phillips® head screwdriver.
4. Push hose adapter into opening and rotate until tab is
under ledge. If installed properly, the hose cannot be
lifted out of the hose opening.
5
Step C Check Disposable Dust Bag
Step D Store Hose and Accessories
1
Hose
Adapter
Dusting
Brush
Upholstery
Tool
Paper Bag Collar
1. Check to be sure the paper bag collar is secure with
the hose adapter inside the paper bag collar.
Crevice
Tool
Carrying
Handle
|
Telescoping
Wand
Hose
Retainer
Step E Store Electrical Cord
2. Replace front bag cover. Place the tabs on the bag
cover in the slots at the bottom of the bag
compartment. Using both hands, one on each side,
press the bag cover firmly back against unit until latch
clicks shut.
1
Cord
Hook
1. Wind the cord around the two cord hooks on the left
side of cleaner. On some models the upper cord hook
turns to release the cord. Turn the hook up to store the
cord.
2. Secure the plug to the cord to prevent unwinding.
1
Cord
Hook
6
HOW TO USE
The upright vacuum cleaner design allows use on multiple types of
carpeting and on upholstery or bare floors with attachments. When
using the attachment tools, place the handle in the upright
position. Do not place cleaner on furniture or steps as the brush
roll may cause damage.
4
ON/OFF
1. Adjust cleaner height setting knob to lowest position for maximum
cleaning. Adjust to a higher setting to make pushing easier. For
easy adjustments, tilt the cleaner back to move the knob.
2. Plug electrical cord into outlet.
2
3. Step on handle release. Pull handle back to a comfortable position.
4. Push On (-) or Off (0) power switch.
Store or
Use Attachments
Use
3
Handle
Release
Clean
Under
3
Handle
Release
LO
Cleaner Height Setting
WARNING: Avoid injury. Keep loose clothing,
hair, fingers, and all other parts of body away
from any moving part (such as the revolving
brush). Turn off the switch and unplug the
cleaner before changing the cleaner height
setting.
The front of the cleaner has an adjustment that
raises or lowers the cleaner base to match the
type of carpet. With the cleaner cord unplugged,
set the adjustment to lowest setting for maximum
cleaning. If the cleaner is difficult to push, move
adjustment to next highest setting until cleaner
is comfortable to push. The brush roll must reach
the carpet for effective cleaning.
Make each adjustment with cleaner switch off
and cord disconnected from outlet. For ease
in moving the adjustment knob, place handle in
operating position and tilt cleaner back to remove
weight from front wheels.
W
1
HI
GH
THERMAL CUT OFF
This cleaner has a special thermostat that protects the cleaner
in case of motor overheating. If the cleaner suddenly turns off,
follow this procedure:
1. Push power switch off.
2. Unplug cleaner.
3. Check for source of overheating problem (i.e. full bag, clogged
hose or clogged filter).
4. If a full bag, clogged hose or clogged filter is found, replace the
bag, unclog the hose or replace the filters.
5. Wait at least 30 minutes before attempting to reuse the cleaner.
6. After 30 minute cool down period, plug the cleaner in and push
the switch pedal. The cleaner should turn on.
7. If the cleaner still does not operate, take it to any Eureka
Authorized Service Center for repair.
7
How To Use Accessories
Crevice tool cleans corners, baseboards, between
NOTE: Do not place cleaner on furniture or steps as
the brush roll may cause damage. Place
cleaner on floor with the handle in storage
position while using accessories.
cushions, sliding door tracks.
.
1. Remove hose from rear of cleaner.
2. Place desired accessory onto end of hose.
Dusting Brush is for furniture, blinds, books, lamp shades,
shelves.
.
Upholstery nozzle is for curtains, draperies, cushions,
fabrics.
.
Telescoping wand
To use the telescoping wand, push button and pull out wand
until you have the desired length. Release button.
Button
8
HOW TO MAINTAIN
The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the bag,
belt, and brush roll often.
Brush Roll
The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it continues
brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length,
hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brush roll.
Brush Roll Belt
The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be sure it is
in good condition. Replace the belt if it stretches, cracks or loses tension. Cut away any hair or threads wound around the
brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly.
How To Replace Brush Roll Belt
NOTE: Turn off the switch and unplug the electrical cord before replacing belt. Belt pulleys can become hot
during normal use. To prevent injury, avoid touching the motor pulley when checking the belt.
4
Motor
Pulley
Belt
2
1
2
Brush
Roll
3
1. Lower handle to floor to change belt.
3. Lift left end of brush roll.
2. Loosen the two fasteners located on the top of the
hood and lift upward. These fasteners need only a
quarter turn to lock or unlock the hood.
4. Remove and discard belt.
9
5
8
5. Place new belt around motor pulley.
8. Pull right side of brush roll to stretch belt. Secure right
end cap into base.
6
7
9
Left side view
9. Rotate brush roll to seat belt.
6. Place belt around brush roll pulley.
7. Align left end cap with square in base. Push end cap
into place; see left side view.
10. Replace the hood. Make sure hood front is behind
furniture guard. Hood should seat onto self-locating
fastener tabs.
11. Turn fasteners 1/4 turn to lock.
Disposable Dust Bag and Filters
The disposable dust bag plays a very important role in
the efficiency of a vacuum cleaner. The purpose of the
paper bag is to trap dirt. As the bag traps dirt, it must also
be porous enough to allow air to pass on through. If the
paper bag becomes clogged, no air can pass through the
cleaner and no cleaning can take place regardless of how
powerful the unit. Change the dust bag and check the filters
frequently. Some fine particles can restrict airflow very
quickly and will decrease performance even before the
bag appears to be full.
Use GENUINE EUREKA replacement belt, 54312.
Look for the
10
product symbol.
When vacuuming carpet fresheners or cleaners, powder,
plaster dust, or similar fine substances, the bag and filters
may require more frequent maintenance.
How To Replace Bags–Style AA Filteraire
NOTE: Turn off the switch and unplug the electrical cord before changing dust bag. Never operate the vacuum
cleaner without the dust bag or the filter.
NOTE: Style AA Filteraire bags must be used to maintain HEPA grade filtration and prolong the life of the HEPA
filter.
To Remove Bag:
|
| |
B
|
Front Cover
Latch
A
Front
Cover
A. Remove front cover by pulling out on the front
cover latch and lifting the front cover upward
and out.
B. Remove left side of bag collar from bag collar
retainer. Grasp bag collar; pull down slightly
and out to remove bag.
F
To Replace New Bag:
C. Fold sides on new paper bag below bag collar.
E
D. Align bag collar hole and notch with hose tube.
E. Place rear of bag collar on ledges. Push back
and rotate upward until firmly in place. Make
sure collar snaps into position and hose tube
is securely inserted into bag collar hole.
F.
Tuck bag into bottom and along sides.
G. Align front cover tabs and close cover. Make
sure paper bag is not caught under the front
cover.
D
Bag
Collar
{,yz|
E
C
Bag
Side
We recommend using only Genuine Eureka
Filteraire AA Bags, part number 58623.
11
How to Check and Clear Hose Blockages
Low suction or poor pickup may be due to a blockage in the vacuum cleaner.
1. Remove hose and check suction at end of hose - if little or
no suction, check disposable dust bag. Change if needed.
If no improvement proceed to Step 2.
NOTE: Turn off the switch and unplug the electrical cord
before clearing hose.
1
2. Remove the front bag cover. To remove hose adapter from
opening, twist hose adapter clockwise and lift upward.
Once the hose is removed from the cleaner check for any
obstructions that may be in the hose. Any obstructions can
be removed by using a blunt instrument to clear the hose.
Flexing the hose may help loosen the clog.
3. Reinstall the hose after clearing the clog. Make sure the
hose is inserted into the top of the vacuum cleaner.
NOTE: If no improvement in performance on carpet, proceed
to following page.
1. Remove hose and check suction at end of
hose.
4
#
|
Hose Adapter
|
2. Remove front bag cover.
3. Remove hose adapter by twisting clockwise and lifting
upward. Check hose for blockages.
4. Reinstall the hose and replace front bag
cover.
12
How to Check and Clear Blockages in Base
1. Remove the attachment hose from the lower hose
retainer and look into the hose retainer for any
obstructions. Proceed to Step 2 to check for any other
blockages.
2. Remove the hood by loosening the two fasteners
located on the top of the hood and lifting upward.
These fasteners need only a quarter turn to lock or
unlock the hood. (See padlock graphics on the hood.)
Upright position
Operating Position
Handle
Release
Lowest Position
for cleaning
under furniture
3. Step on the handle release and lower the handle all
the way to the floor.
4. Check for blockages in the brush roll area and remove
any obstructions found there. The base hose can be
cleared of any blockage by using a blunt instrument.
5. After the blockage is removed, replace the hood and
tighten the two hood screws (see Figure 2). Raise the
handle to the upright position (see Figure 3) and replace
the hose into the lower hose retainer.
13
Motor Filter
Check the motor filter with each disposable dust
bag change. Clean or replace as needed.
3
To Clean Motor Filter
y
,
z
|
z
y
,
{
{|€
Back Ledge
1. Remove filter from inside bag compartment,
lower left side.
3
2. Shake filter or vacuum with another cleaner
to remove excess dust.
Filter Retainer
1 and 3
HEPA Filter
Check the HEPA filter with each disposable dust bag
change. Replace twice a year or as needed.
.
3. Reinstall filter. Slide under back ledge and
filter retainer. Install with colored/smooth side
down.
.
Latch
To remove HEPA Filter
1. Push down latch and pull HEPA filter back.
2. Then lift filter up and remove.
To replace HEPA Filter
1. Place bottom tabs of filter into slots.
2. Rotate filter toward cleaner.
Obtain replacement filters from a local dealer or order
them from The Eureka Company, Bloomington, IL.
14
3. Push upward on the latch to secure into place.
How To Change Light Bulb (only for models with a headlight)
NOTE: Turn off the power switch and
disconnect the electrical cord
before changing light bulb.
1. Lower handle to remove two screws from lens cover.
1
2. Pull lens cover from cleaner.
3. Pull light bulb and socket toward front.
4. Push light bulb into socket; turn to release.
5. Place new light bulb into socket; turn to secure.
6. Push light bulb and socket back so bulb will not touch
lens cover.
7. Replace lens cover.
4
8. Secure with two screws.
2
5
3
Use 15 watt replacement light bulb, part
number 48815.
15
PROBLEM SOLVING
NOTE: Turn off the switch and unplug the electrical cord before servicing.
PROBLEM
CAUSE
SOLUTION
Motor will not start.
3 Electric Plug
Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
Motor suddenly stops.
3 Thermal Cut Off
Refer to page 7.
Does not clean the carpet
or floor.
3 Disposable Dust Bag
Change the bag and clean or replace the
filter(s). Hint: If picking up fine dust, the bag
may not look full but a fine substance tends
to reduce suction when it blocks the airflow
through the paper bag and filter(s).
No suction at the end of
the hose.
and Filter(s)
3 Dust Bag
Be sure hose adapter inserts into paper bag.
3 Belt
Replace a cut, loose or out of shape belt.
3 Belt Cover
Snap the belt cover inside the hood if it comes
loose.
3 Brush Roll
Clean hair and thread from bristles and end
cap area. Replace brush roll if bristles are worn.
3 Hose
Remove any clogs from the hose that restrict
the airflow. Check short hose in the base and
long hose. Refer to page 12 & 13.
3 Hose Adapter
Hose adapter has to seat inside the dust bag.
3 Disposable Dust Bag
Change the bag and clean or replace the
filter(s). Hint: If picking up fine dust, the bag may
not look full, but a fine substance tends to reduce
suction when it blocks the airflow through the
paper bag and filter(s).
and Filter(s)
3 Hose
Remove any clogs from the hose that restrict the
airflow. Check short hose in the base and long
hose. Refer to page 12 & 13.
Headlight not working.
3 Light Bulb
Replace light bulb.
Noise from the brush roll
area.
3 Brush Roll
Remove hood and clean debris or items
from the brush roll area.
3 Belt
Replace a cut, loose or out of shape belt.
3 Cleaner Height Setting
Put handle in operating position. Tilt the
cleaner back to raise the front wheels off floor.
Then turn the knob to a higher setting.
3 Belt
Replace a cut, loose or out of shape belt.
3 Cleaner Height
Hint: Put handle in operating position. Tilt the
cleaner back to raise the front wheels off floor.
Then turn the knob.
Cleaner is hard to push.
Cleaner height knob will
not turn.
16
Setting
VACUUM CLEANERS
S
O
L
D
T
O
9/00
The Eureka Company
P.O. Box 2799
Bloomington, IL 61702-2799
ORDER FORM
(Not applicable in Canada)
Name
Name
Address (street address needed for UPS)
City
Telephone
State
(Day)
Zip
(Eve)
(Fax)
S
H
I
P
Address (street address needed for UPS)
T
O
Telephone
City
IMPORTANT:
Be sure to include
your model, type,
and serial numbers.
These numbers
may be found on
the rating plate.
(Day)
Part No.
State
Zip
(Eve)
(Fax)
Qty. Price (USD)
Total
Genuine Eureka Bags, Belts and Filters
Disposable Dust Bags, package of 3 - Style AA
58236A
3.99
Disposable Dust Bags, package of 10 - Style AA
54926
9.99
Disposable Dust Bags - High Filtration, pkg of 3
58623A
6.99
HEPA Filter
60285
29.99
High Efficiency Motor Filter
39334
1.59
Belts - Style U - Extended Life, package of 2
61120
3.99
60424
22.39
Dusting Brush
60290-1
5.39
Upholstery Nozzle
38284-3
3.19
Crevice Tool, 8 inch
26708-119N
2.59
Deluxe Floor & Wall Brush
54779
11.99
Micro Tool Set for Keyboards, etc.
54002
12.99
60920-1
15.79
Light Bulb
48815
1.59
Brush Roll
60909-1
10.59
Model Number:
Type:
Serial Number:
To Order
By Phone
1-800438-7352*
Accessories/Tools
Telescopic Wand
#
HOURS:
Call between 8 a.m.
and 4:45 p.m.,
central standard time
Monday through Friday.
By FAX
1-309823-5789
To Answer Problems
or Questions for U.S.A.
and Canada call:
1-800282-2886*
7 a.m. to 8 p.m.
central standard time
Monday through Saturday
*En Mexico Llame
254 23 52
Hose Assembly
Miscellaneous Parts
By Mail
Simply fill out
this Order Form.
Please be sure to
include day
and evening
phone numbers.
Total (prices subject to change without notice)
Tax (add state tax & local taxes as required by law)
www.eureka.com
Postage & Handling Charge (within U.S.A.)
Method of payment (no C.O.D. orders)
5.50
Check or money order (payable to The Eureka Company). Do not send currency.
Charge to my
Visa (13/15 digits)
MasterCard (13 digits)
Amer. Express (15 digits)
TOTAL
TOTAL ENCLOSED
Acct. number
Expiration Date
Signature (full name as shown on acct.)
Part No. 70221
© 2000 White Consolidated Industries, Inc.
Printed in U.S.A.
THE EUREKA LIMITED WARRANTY
What This Warranty Covers
Your Eureka cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of two years. The warranty is granted only to the
original purchaser and members of his or her immediate household. The warranty is subject to the following provisions.
What This Warranty Does Not Cover
• Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, and brush roll bristles
• Damages or malfunctions caused by negligence, abuse, or use not in accordance with the Owner’s Guide.
• Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts.
What The Eureka Company Will Do
The Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this warranty. As a matter of warranty policy, the Eureka Company
will not refund the consumer’s purchase price.
Warranty Registration
Please fill out and return the warranty registration card accompanying your cleaner.
Obtaining Warranty Service
To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station.
You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners–Service and Repair.” Be certain that the Warranty Station is “Eureka Authorized.”
For the location of the nearest Eureka Authorized Warranty Station or for service information, telephone toll free:
USA: 1-800-282-2886
Mexico: 254 23 52
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company,
866 Langs Drive, Cambridge, Ontario N3H 2N7.
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping charges to the Eureka Authorized Warranty Station.
Return shipping charges will be paid by the Warranty Station. When returning parts for repair, please include the model, type, and serial number from the data plate on the cleaner.
Further Limitations and Exclusions
Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of Merchantability or any warranty for Fitness For A Particular
Purpose is limited to the duration of this warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided above. In no event shall Eureka be liable for any consequential or incidental damages you
may incur in connection with your purchase or use of the cleaner. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary by state.
GENUINE
EUREKA PRODUCT
Questions & Answers about Genuine Eureka Products
Q: Why should I use only Genuine Eureka paper bags, belts, and parts in my Eureka vacuum cleaner?
A: Using Genuine Eureka Products, which are made to our exacting specifications and engineered with emphasis on quality, performance, and customer satisfaction,
ensures the long life and cleaning efficiency of your vacuum cleaner. Overall, this saves you money and helps to keep your home clean.
Q: How can I be sure I am using only genuine Eureka products in my vacuum cleaner?
A: Typically, packaged products and paper bags can be identified by a “Genuine Eureka Product” symbol (see illustration above). For further identification assistance,
you may call our toll-free number, 1-800-282-2886, for the location of a nearby Eureka Authorized Warranty Station.
Q: Are there any differences between “made to fit” or “imitation” and Genuine Eureka paper bags, belts, and parts?
A: Yes, there are some very important differences in materials, quality, and reliability. Many customers have mistakenly purchased “imitation” paper bags and parts
while thinking they purchased genuine. Unfortunately, many of these customers discovered the differences after they experienced related difficulties.
For Genuine Eureka Value, Accept No Imitations!
THE EUREKA COMPANY
Household Warranty
abs 190
Bloomington, Illinois 61701
19
Assembly Items in This Carton
1 crevice tool
1 hardware
package (2 screws)
1 dusting brush
1 hose adapter w/hose
1 telescoping wand
1 cleaner connected
to handle by cord
1 upholstery brush
1 front cover
Thank you for selecting a Eureka cleaner.
Don’t Forget to Use Genuine Eureka Bags and Belts
Caution: Damages caused by the use of non-genuine
Eureka bags are not covered by the Eureka Limited
Warranty.
Part No. 70220A (9/00)
©1999 White Consolidated Industries, Inc.
Printed in U.S.A.
Download PDF