Makita | DF010D | Instruction manual | Makita DF010D Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
In-line Cordless Driver Drill
DF010D
008706
IMPORTANT: Read Before Using.
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model
DF010D
Steel
Capacities
6 mm
Wood screw
ø3.8 mm x 45 mm
Machine screw
M5
High (2)
650
-1
No load speed (min )
Overall length
5 mm
Wood
Low (1)
200
Straight type
279 mm
Pistol type
224 mm
Net weight
0.55 kg
Rated voltage
D.C. 7.2 V
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END004-4
ENG900-1
Vibration
The vibration total value (tri-axial
determined according to EN60745:
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
・ Read instruction manual.
Cd
Ni-MH
Li-ion
・
ENG901-1
•
•
•
•
ENE034-1
Intended use
The tool is intended for drilling and screw driving in
wood, metal and plastic.
ENG905-1
noise
level
sum)
Work mode: drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
Noise
The typical A-weighted
according to EN60745:
vector
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-17
determined
For European countries only
EC Declaration of Conformity
Sound pressure level (LpA) : 70 dB (A) or less
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A)
Makita declares that the following Machine(s):
Designation of Machine:
In-line Cordless Driver Drill
Model No./ Type: DF010D
Conforms to the following European Directives:
2006/42/EC
Wear ear protection
2
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dustrelated hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
They are manufactured in accordance with the following
standard or standardized documents:
EN60745
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
31.12.2013
000331
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
GEA006-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
3
29.
18.
Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair
person
using
only
identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
30.
Follow instruction for lubricating and
changing accessories.
Keep handles dry, clean and free from oil and
grease.
GEB088-1
CORDLESS DRIVER DRILL
SAFETY WARNINGS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Hold power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Always be sure you have a firm footing.
Be sure no one is below when using the tool
in high locations.
Hold the tool firmly.
Keep hands away from rotating parts.
Do not leave the tool running. Operate the tool
only when hand-held.
Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
4
ENC007-7
FUNCTIONAL DESCRIPTION
IMPORTANT SAFETY
INSTRUCTIONS
•
FOR BATTERY CARTRIDGE
1.
2.
3.
4.
5.
6.
7.
8.
9.
Before using battery cartridge, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such
as nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ゚ C (122 ゚ F).
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Do not use a damaged battery.
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
1
1. Button
2. Battery cartridge
2
008707
•
•
•
•
Always switch off the tool before insertion or
removal of the battery cartridge.
To remove the battery cartridge, withdraw it from
the tool while pressing the buttons on both sides of
the cartridge.
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If not, it may
accidentally fall out of the tool, causing injury to
you or someone around you.
Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Lock button
A
B
1
1. Lock button
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.
Charge
the
battery
cartridge
before
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room
temperature at 10 ゚ C - 40 ゚ C (50 ゚ F - 104 ゚ F).
Let a hot battery cartridge cool down before
charging it.
Charge the battery cartridge once in every six
months if you do not use it for a long period of time.
008708
When the lock button is in the locked position B, the
switch cannot be actuated.
When the lock button is in the unlocked position A, the
switch can be actuated.
5
Switch action
A
Adjusting the fastening torque
B
1
C
1. Lock button
2. Switch
1. Graduation
2. Adjusting ring
3. Pointer
2
1
.
D
2
3
008711
008713
CAUTION:
•
Before inserting the battery cartridge into the tool,
always check to see that the switch actuates
properly and returns to the "OFF" position when
released.
To start the tool, first move the lock button to the
unlocked position A to release the switch. And then
simply push the switch on the
C side for the
clockwise rotation and the
D side for the
counterclockwise rotation Release the switch to stop.
The fastening torque can be adjusted in 21 steps by
turning the adjusting ring so that its graduations are
aligned with the pointer on the tool body. The fastening
torque is minimum when the number 1 is aligned with
the pointer, and maximum when the
marking is
aligned with the pointer.
The clutch will slip at various torque levels when set at
the number 1 to 21. The clutch is designed not to slip at
the marking.
Before actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
•
•
•
CAUTION:
Always check the direction of rotation before
operation.
Change the direction only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
When not operating the tool, always place the lock
button in the locked position .
NOTE:
•
See the following chart for the relation between
the number of torque setting and fastening torque
rate.
The fastening torque rate will be different depends
on materials. Make a test fastening to get the
desired torque before operation.
Speed change
1. Speed change
lever
.
1
2
1
008712
To change the speed, first switch off the tool and then
slide the speed change lever to the "2" side for high
speed or "1" side for low speed. Be sure that the speed
change lever is set to the correct position before
operation. Use the right speed for your job.
•
•
CAUTION:
Always set the speed change lever fully to the
correct position. If you operate the tool with the
speed change lever positioned halfway between the
"1" side and "2" side, the tool may be damaged.
Do not use the speed change lever while the tool
is running. The tool may be damaged.
6
Guideline for clutch auto-stop
Work range of clutch auto-stop
High speed
Low speed
Increments on adjusting
ring for fastening torque
Fastening torque
1
Approx. 0.3 N m
(Approx. 3 Kgf-cm)
5
Approx. 0.82 N m
(Approx. 8.4 Kgf-cm)
9
Approx. 1.35 N m
(Approx. 13.8 Kgf-cm)
13
Approx. 1.88 N m
(Approx. 19.2 Kgf-cm)
17
Approx. 2.41N m
(Approx. 24.6 Kgf-cm)
21
Approx. 2.9 N m
(Approx. 30 Kgf-cm)
Clutch auto-stop works
Clutch auto-stop
does not work
Low speed
Approx. 5 N m
(Approx. 49 Kgf-cm)
High speed
Approx. 1.5 N m
(Approx. 14.7 Kgf-cm)
When driving machine
screws
Increments
Guideline for machine screw diameter
1-3
2.5 mm
4-8
3 mm
9 - 18
4 mm
19 - 21
5 mm
013465
7
For European and North & South American
countries, Australia and New Zealand
Lighting up the front lamp
1. Lamp switch
B
A
Use only these type of bit. Follow the
procedure (1).
(Note) Bit-piece is not necessary.
A=12mm
B=9mm
006348
For other countries
1
008715
To install these types of bits, follow
the procedure (1).
(Note) Makita bits are these types.
A=17mm
1. Lamp
B=14mm
To install these types of bits, follow
the procedure (2).
(Note) Bit-piece is necessary for
installing the bit.
A=12mm
B=9mm
1
006349
1.
008716
CAUTION:
•
Do not look in the light or see the source of light directly.
To turn on the light, slide the lamp switch to the A position.
To turn off the light, slide the lamp switch to B position.
Even if you leave the lamp on, the light will
automatically turn off after 5 minutes.
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it will
go. Then release the sleeve to secure the bit.
1. Bit
1
Checking the remaining battery capacity,
auto-stop
The lamp signals by flickering when the battery power is
almost used up during use,.
At this time, recharge the battery or replace the battery
with a fully charged one.
008709
2.
ASSEMBLY
•
CAUTION:
Always be sure that the lock button is in the locked
position B and the battery cartridge is removed
before carrying out any work on the tool.
To install the bit, pull the sleeve in the direction of
the arrow and insert the bit-piece and bit into the
sleeve as far as it will go. The bit-piece should be
inserted into the sleeve with its pointed end facing
in. Then release the sleeve to secure the bit.
1. Bit-piece
2. Sleeve
Installing or removing driver bit or socket bit
1
2
008710
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
•
If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and the
bit will not be secured. In this case, try re-inserting the
004521
Use only the driver bit or socket bit shown in the figure.
Do not use any other driver bit or socket bit.
8
bit according to the instructions above.
Drilling operation
OPERATION
First, turn the adjusting ring so that the pointer points to
the
marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer
at the point to be drilled. Place the point of the bit in the
indentation and start drilling.
Use a cutting lubricant when drilling metals. The
exceptions are iron and brass which should be drilled dry.
The tool can be used in two ways; a straight type and a
pistol type which is selectable according to the
conditions of workplace and screwdriving.
008717
Screwdriving operation
•
•
008714
•
CAUTION:
•
Adjust the adjusting ring to the proper torque level
for your work.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Then switch the tool on.
When the clutch cuts in, the motor will stop
automatically. Then release the switch.
•
•
•
CAUTION:
Make sure that the driver bit is inserted straight in
the screw head, or the screw and/or bit may be
damaged.
CAUTION:
Pressing excessively on the tool will not speed up
the drilling. In fact, this excessive pressure will
only serve to damage the tip of your bit, decrease
the tool performance and shorten the service life
of the tool.
There is a tremendous force exerted on the tool/bit
at the time of hole break through. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece.
A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to
back out. However, the tool may back out abruptly
if you do not hold it firmly.
Always secure small workpieces in a vise or
similar hold-down device.
If the tool is operated continuously until the battery
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
Using the tool as a hand screwdriver
NOTE:
•
When driving wood screws, predrill pilot holes to
make driving easier and to prevent splitting of the
workpiece. See the chart.
Nominal diameter of wood screw
(mm)
Recommended size of pilot hole
(mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
5.8
6.1
2.0 - 2.2
2.2 - 2.5
2.5 - 2.8
2.9 - 3.2
3.1 - 3.4
3.3 - 3.6
3.7 - 3.9
4.0 - 4.2
4.2 - 4.4
008718
Switch off the tool.
Move the lock button to the locked position A.
Turn the tool.
006421
9
NOTE:
•
Use the tool with a fastening torque less than 5 Nm
(50 kgf.cm).
•
This use is convenient for checking the
screwdriving.
•
Do not use the tool for work requiring excessive
force, such as tightening bolt M6 or bolts greater
than M6 or removing rusted screws.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
•
•
CAUTION:
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
OPTIONAL ACCESSORIES
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Drill bits
•
Screw bits
•
Socket bits
•
Bit piece
•
Various type of Makita genuine batteries and
chargers
•
Plastic carrying case
•
NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
10
11
Makita Jan-Baptist Vinkstraat 2, 3070, Belgium
Makita Corporation Anjo, Aichi, Japan
884799D229
12
www.makita.com
Download PDF