GPT SERIES (2006 Release)

GPT SERIES (2006 Release)
M-06-10
REV. B
APRIL 2008
MAINTENANCE MANUAL
GPT-25, GPT-3, GPT-4 & GPT-5
© MAXON Lift Corp. 2008
11921 Slauson Ave.
Santa Fe Springs, CA. 90670
LIFT CORP.
CUSTOMER SERVICE:
TELEPHONE (562) 464-0099 TOLL FREE (800) 227-4116
FAX: (888) 771-7713
NOTE: For latest version of all Manuals (and replacements), download the
Manuals from Maxon’s website at www.maxonlift.com.
WARRANTY/ RMA POLICY & PROCEDURE
LIFTGATE WARRANTY
Type of Warranty:
Full Parts and Labor
Term of Warranty:
Standard Liftgates - 2 years from ship date or 6,000 cycles
Premium Liftgates - 2 years from ship date or 10,000 cycles
This warranty shall not apply unless the product is installed, operated and maintained in accordance with MAXON Lift’s specifications as set forth in
MAXON Lift’s Installation, Operation and Maintenance manuals. This warranty does not cover normal wear, maintenance or adjustments, damage or
malfunction caused by improper handling, installation, abuse, misuse, negligence, or carelessness of operation. In addition, this warranty does not
cover equipment that has had unauthorized modifications or alterations made to the product.
MAXON agrees to replace any components which are found to be defective during the first 2 years of service, and will reimburse for labor based on
MAXON’s Liftgate Warranty Flat Rate Schedule. (Copy of the Flat Rate is available at www.maxonlift.com.)
All warranty repairs must be performed by an authorized MAXON warranty facility. For any repairs that may exceed $500, including parts and labor,
MAXON’s Technical Service Department must be notified and an “Authorization Number” obtained.
All claims for warranty must be received within 30 Days of the repair date, and include the following information:
1. Liftgate Model Number and Serial Number
2. The End User must be referenced on the claim
3. Detailed Description of Problem
4. Corrective Action Taken, and Date of Repair
5. Parts used for Repair, Including MAXON Part Number(s)
6. MAXON R.M.A. # and/or Authorization # if applicable (see below)
7. Person contacted at MAXON if applicable
8. Claim must show detailed information i.e. Labor rate and hours of work performed
Warranty claims can also be placed online at www.maxonlift.com. Online claims will be given priority processing.
All claims for warranty will be denied if paperwork has not been received or claim submitted via Maxon website for processing by MAXON’s Warranty
Department within 30 days of repair date.
All components may be subject to return for inspection, prior to the claim being processed. MAXON products may not be returned without prior written
approval from MAXON’s Technical Service Department. Returns must be accompanied by a copy of the original invoice or reference with original
invoice number and are subject to a credit deduction to cover handling charges and any necessary reconditioning costs. Unauthorized returns will be
refused and will become the responsibility of the returnee.
Any goods being returned to MAXON Lift must be pre-approved for return, and have the R.M.A. number written on the outside of the package in plain
view, and returned freight prepaid. All returns are subject to a 15% handling charge if not accompanied by a detailed packing list. Returned parts
are subject to no credit and returned back to the customer. Defective parts requested for return must be returned within 30 days of the claim date for
consideration to:
MAXON Lift Corp.
10321 Greenleaf Ave., Santa Fe Springs, CA 90670
Attn: RMA#__
MAXON’s warranty policy does not include the reimbursement for travel time, towing, vehicle rental, service calls, oil, batteries or loss of income due to
downtime. Fabrication or use of non Maxon parts, which are available from MAXON, are also not covered.
MAXON’s Flat Rate Labor Schedule takes into consideration the time required for diagnosis of a problem.
All Liftgates returned are subject to inspection and a 15% restocking fee. Any returned Liftgates or components that have been installed or not returned
in new condition will be subject to an additional reworking charge, which will be based upon the labor and material cost required to return the Liftgate or
component to new condition.
PURCHASE PART WARRANTY
Term of Warranty: 1 Year from Date of Purchase.
Type of Warranty: Part replacement only. MAXON will guarantee all returned genuine MAXON replacement parts upon receipt and inspection of parts
and original invoice.
All warranty replacements parts will be sent out via ground freight. If a rush shipment is requested, all freight charges will be billed to the requesting
party.
TABLE OF CONTENTS
WARNINGS ........................................................................................................................... 6
SAFETY INSTRUCTIONS .................................................................................................... 6
LIFTGATE TERMINOLOGY .................................................................................................. 9
PERIODIC MAINTENANCE................................................................................................ 10
PERIODIC MAINTENANCE CHECKS ................................................................................ 10
PERIODIC MAINTENANCE CHECKLIST ............................................................................11
CHECK HYDRAULIC FLUID ............................................................................................... 12
CHANGING HYDRAULIC FLUID ........................................................................................ 13
REPLACING PLATFORM TORSION SPRING ................................................................... 14
PLATFORM ADJUSTMENT ................................................................................................ 15
PARTS BREAKDOWN ....................................................................................................... 17
MAIN ASSEMBLY (ALUMINUM PLATFORM) ..................................................................... 17
MAIN FRAME ASSEMBLY: GPT-25 & GPT-3 ..................................................................... 18
MAIN FRAME ASSEMBLY: GPT-4 & GPT-5 ....................................................................... 22
PLATFORM & FLIPOVER ASSEMBLY (ALUMINUM)......................................................... 26
PLATFORM & FLIPOVER ASSEMBLY WITH CART STOPS (ALUMINUM)....................... 27
PLATFORM ASSEMBLY (ALUMINUM) ............................................................................... 28
FLIPOVER WITH SINGLE CART STOP (ALUMINUM) ...................................................... 30
FLIPOVER WITH DUAL CART STOPS (ALUMINUM) ........................................................ 32
DOCK BUMPER .................................................................................................................. 34
HYDRAULIC COMPONENTS - POWER DOWN ................................................................ 36
PUMP ASSEMBLY - POWER DOWN ................................................................................. 38
PUMP BOX ASSEMBLY - POWER DOWN......................................................................... 40
CONTROL SWITCH AND POWER CABLE ........................................................................ 41
DECALS .............................................................................................................................. 42
SYSTEM DIAGRAMS ......................................................................................................... 46
HYDRAULIC SCHEMATIC - POWER DOWN..................................................................... 46
ELECTRICAL SCHEMATIC - POWER DOWN ................................................................... 47
TROUBLESHOOTING ........................................................................................................ 48
PLATFORM WILL NOT RAISE............................................................................................ 48
PLATFORM RAISES BUT LEAKS DOWN .......................................................................... 49
PLATFORM RAISES PARTIALLY AND STOPS .................................................................. 50
LIFTGATE WILL NOT LIFT RATED CAPACITY .................................................................. 51
PLATFORM RAISES SLOWLY ........................................................................................... 52
PLATFORM WILL NOT LOWER, LOWERS TOO SLOWLY OR TOO QUICKLY ................ 54
PLATFORM WON’T TILT DOWN TO THE GROUND ......................................................... 56
Comply with the following WARNINGS and SAFETY INSTRUCTIONS while maintaining
Liftgates. See Operation Manual for operating safety requirements.
WARNINGS
!
WARNING
• Do not stand, or allow obstructions, under the platform when lowering the Liftgate. Be sure your
feet are clear of the Liftgate.
• Keep fingers, hands, arms, legs, and feet clear of moving Liftgate parts (and platform
edges) when operating the Liftgate.
• Correctly stow platform when not in use. Extended platforms could create a hazard for
people and vehicles passing by.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
• Disconnect Liftgate power cable from battery before repairing or servicing Liftgate.
• If it is necessary to stand on the platform while maintaining the Liftgate, keep your feet and any
objects clear of the inboard edge of the platform. Your feet or objects on the platform can become
trapped between the platform and the Liftgate extension plate.
• Recommended practices for welding on steel parts are contained in the current AWS (American
Welding Society) D1.1 Structural Welding Code - Steel. Damage to Liftgate and/or vehicle, and
personal injury could result from welds that are done incorrectly.
• Recommended practices for welding on aluminum parts are contained in the current AWS
(American Welding Society) D2.1 Structural Welding Code - Aluminum. Damage to Liftgate
and/or vehicle, and personal injury could result from welds that are done incorrectly.
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
• Read and understand the instructions in this Maintenance Manual before performing maintenance on the Liftgate.
• Before operating the Liftgate, read and understand the operating instructions in Operation
Manual.
• Comply with all WARNING and instruction decals attached to the Liftgate.
• Keep decals clean and legible. If decals are illegible or missing, replace them. Free replacement
decals are available from Maxon Customer Service.
• Consider the safety and location of bystanders and location of nearby objects when operating the
Liftgate. Stand to one side of the platform while operating the Liftgate
• Do not allow untrained persons to operate the Liftgate.
• Wear appropriate safety equipment such as protective eyeglasses, faceshield and clothing while
performing maintenance on the Liftgate and handling the battery. Debris from drilling and contact
with battery acid may injure unprotected eyes and skin.
• Be careful working by an automotive type battery. Make sure the work area is well ventilated and
there are no flames or sparks near the battery. Never lay objects on the battery that can short the
terminals together. If battery acid gets in your eyes, immediately seek first aid. If acid gets on your
skin, immediately wash it off with soap and water.
6
• A correctly installed Liftgate operates smoothly and reasonably quiet. The only noticeable noise
during operation comes from the power unit while the platform is raised. Listen for scraping, grating and binding noises and correct the problem before continuing to operate Liftgate.
• Use only Maxon Authorized Parts for replacement parts. Provide Liftgate model and serial number information with your parts order. Order replacement parts from:
MAXON LIFT CORP. Customer Service
11921 Slauson Ave., Santa Fe Springs, CA 90670
Online: www.maxonlift.com
Express Parts Ordering: Phone (800) 227-4116 ext. 4345
Email: Ask your Customer Service representative
7
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
• If an emergency situation arises (vehicle or Liftgate) while operating the Liftgate, release the control switch to stop the Liftgate.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
THIS PAGE INTENTIONALLY LEFT BLANK
8
EXTENSION
PLATE
SADDLE
CONTROL
SWITCH
DOCK
BUMPER
MAIN
FRAME
LIFT
CYLINDER
PARALLEL
ARM
PUMP BOX
PLATFORM
TORSION
SPRING
PLATFORM
OPENER
WEDGE FLIPOVER
9
LIFT
ARM
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
LIFTGATE TERMINOLOGY
PERIODIC MAINTENANCE
PERIODIC MAINTENANCE CHECKS
!
WARNING
Never operate the Liftgate if parts are loose or missing.
NOTE: Make sure vehicle is parked on level ground while performing the
maintenance checks.
Quarterly or 1250 Cycles (whichever occurs first)
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
Check the hydraulic fluid level in the pump reservoir. Refer to the CHECKING HYDRAULIC
FLUID procedure in the PERIODIC MAINTENANCE section.
If hydraulic fluid appears contaminated, refer to the CHANGING HYDRAULIC FLUID
procedure in the PERIODIC MAINTENANCE section.
Keep track of the grade of hydraulic fluid in the pump reservoir and never mix two different
grades of fluid.
Check all hoses and fittings for chafing and fluid leaks. Tighten loose fittings or replace
parts as required.
Check electrical wiring for chafing and make sure wiring connections are tight and free of
corrosion. Use dielectric grease to protect electrical connections.
Check that all WARNING and instruction decals are in place. Also, make sure decals are
legible, clean and undamaged.
Check that all bolts, nuts, and roll pins are in place. Make sure roll pins protrude evenly
from both sides of hinge pin collar. Replace fasteners and roll pins if necessary.
CAUTION
Damaged cylinder seals and contaminated hydraulic fluid can result from painting the polished portion of the cylinder rod. To prevent damage, protect the
exposed polished portion of the cylinder rod while painting.
Check for rust and oily surfaces on Liftgate. If there is rust or oil on Liftgate, clean it off.
Touch up the paint where bare metal is showing. MAXON recommends using the aluminum
primer touchup paint kit, P/N 908119-01.
Semi-annually or 2500 Cycles (whichever occurs first)
Visually check the platform hinge pins for excessive wear and broken welds. See PARTS
BREAKDOWN section for replacement parts. Also, do the Quarterly or 1250 Cycles
maintenance checks.
10
NOTE: Make sure vehicle is parked on level ground while performing maintenance
checks.
Quarterly or 1250 Cycles (whichever occurs first)
Check the level and condition of the hydraulic fluid.
Visually check all hoses and fittings for chafing and fluid leaks. Tighten loose fittings or
replace parts as required.
Check electrical wiring for chafing and make sure wiring connections are tight and free
of corrosion. Use dielectric grease to protect electrical connections.
Check that all WARNING and instruction decals are in place. Also, make sure decals
are legible, clean, and undamaged.
Check that all bolts, nuts, and roll pins are in place. Make sure roll pins protrude evenly
from both sides of hinge pin collar. Replace fasteners and roll pins if necessary.
Check for rust and oily surfaces on Liftgate. If there is rust or oil on Liftgate or if the
Liftgate is dirty, clean it off. Touch up the paint where bare metal is showing. Refer to
the paint system CAUTION and recommended touchup kit on the preceding page.
Semi-annually or 2500 Cycles (whichever occurs first)
Visually check the platform hinge pins for excessive wear and broken welds.
Do the Quarterly or 1250 Cycles Checks on this checklist.
11
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
PERIODIC MAINTENANCE CHECKLIST
PERIODIC MAINTENANCE
CHECK HYDRAULIC FLUID
CAUTION
Keep dirt, water and other contaminants from entering the hydraulic system.
Before opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up contaminants that can get in the openings. Also, protect the
openings from accidental contamination.
NOTE: Use correct grade of hydraulic fluid for your location.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
+50 to +120 Degrees F - Grade ISO 32
Below + 70 Degrees F - Grade ISO 15 or MIL-H-5606
See TABLES 12-1 & 12-2 for recommended brands.
1. Remove the filler cap (FIG. 12-1).
PUMP
RESERVOIR
ISO 32 HYDRAULIC OIL
RECOMMENDED
BRANDS
FILLER
CAP
DECAL
(FLUID LEVEL)
PART NUMBER
AMSOIL
AWH-05
CHEVRON
HIPERSYN 32
KENDALL
GOLDEN MV
SHELL
TELLUS T-32
EXXON
UNIVIS N-32
MOBIL
DTE-13M, DTE-24,
HYDRAULIC OIL-13
TABLE 12-1
CHECKING HYDRAULIC FLUID LEVEL
FIG. 12-1
ISO 15 OR MIL-H-5606 HYDRAULIC OIL
2. Check the hydraulic fluid level in the
pump reservoir (FIG. 12-1). If fluid
is below FILL LEVEL shown on decal on the pump reservoir (FIG. 121), add fluid to the FILL LEVEL.
RECOMMENDED
BRANDS
NOTE: If the hydraulic fluid in the
reservoir is contaminated, do
the CHANGING HYDRAULIC
FLUID procedure in this section.
PART NUMBER
AMSOIL
AWF-05
CHEVRON
FLUID A, AW-MV-15
KENDALL
GLACIAL BLU
SHELL
TELLUS T-15
EXXON
UNIVIS HVI-13
MOBIL
DTE-11M
ROSEMEAD
THS FLUID 17111
TABLE 12-2
3. Reinstall the filler cap (FIG. 12-1).
12
CAUTION
Keep dirt, water and other contaminants from entering the hydraulic system.
Before opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up contaminants that can get in the openings. Also, protect the
openings from accidental contamination.
NOTE: Use correct grade of hydraulic fluid for your location.
+50 to +120 Degrees F - Grade ISO 32
Below + 70 Degrees F - Grade ISO 15 or MIL-H-5606
See TABLES 12-1 & 12-2 for recommended brands.
NOTE: To prevent spills, drain used hydraulic fluid through a funnel into waste fluid container.
1. Place empty 5 gallon bucket under drain plug.
PUMP BOX
2. Open and raise platform to vehicle bed height.
Remove the drain plug (FIG. 13-1). Drain
hydraulic fluid.
DRAIN
PLUG
3. Disconnect the white wire (FIG. 13-2) from
motor solenoid. Lower the platform while
draining the remaining hydraulic fluid from
system. Reinstall drain plug. Reconnect the
white wire to motor solenoid.
4. Remove filler cap (FIG. 13-2) and refill
reservoir to the level shown on decal.
FIG. 13-1
FILLER
CAP
5. Raise platform to vehicle bed
height. Check hydraulic fluid again
and, if needed, add more hydraulic
fluid (FIG. 13-2).
6. Reinstall filler cap (FIG. 13-2).
WHITE
WIRE
MOTOR
SOLENOID
13
DECAL
(FLUID LEVEL)
FIG. 13-2
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
CHANGING HYDRAULIC FLUID
PERIODIC MAINTENANCE
REPLACING PLATFORM TORSION SPRING
NOTE: The following procedure shows how to replace torsion spring on RH side of
platform. Use this procedure for replacing torsion spring on the LH side.
1. Manually fold flipover onto platform.
2. Raise platform to a convenient work height
PLATFORM
to gain access and release tension on the (REFERENCE)
torsion spring.
HINGE
BRACKET
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
TORSION
SPRING
HINGE PIN
!
CAUTION
To prevent injury and equipment damage, make sure there is no tension on
torsion spring before removing hinge pin.
LOCK
NUT
BOLT
3. Unbolt hinge pin from hinge bracket
(FIG. 14-1). Remove bolt and lock nut.
Drive the hinge pin inboard toward the
shackle with a hammer and pin punch,
just enough to free the torsion spring
(FIG. 14-1). Remove spring from shackle.
4. Install the torsion spring as shown in
FIG. 14-2. Make sure the long leg
of the spring is inserted in the bracket
located on shackle (FIG. 14-2). Make
sure the short end of the spring is visible and resting against the edge of the
hinge bracket (FIG. 14-2).
5. Drive the hinge pin into correct position (FIG. 13-2) through the hinge
bracket with a hammer and pin
punch. Line up the bolt hole in the
hinge pin with the hole in the hinge
bracket. Bolt the hinge pin to hinge
bracket with bolt and lock nut (FIG.
13-2).
FIG. 14-1
SHACKLE
HINGE PIN
HINGE
BRACKET
PLATFORM
(REFERENCE)
BOLT &
LOCK NUT
BRACKET
LONG
LEG
SHORT
LEG
6. Operate the Liftgate to make
sure it operates correctly.
FIG. 14-2
14
SHACKLE
NOTE: Before doing the following procedure, make sure vehicle is parked
on level ground.
1. With the platform and flipover unfolded,
raise platform to bed level (FIG. 15-1).
Measure how much the outboard edge
of platform rises above bed level (FIG.
15-1). The outboard edge must be level
or a maximum of 2” above bed level (FIG.
15-1). If indication is correct, Liftgate
is installed correctly and no adjustment
is needed. If the outboard edge is below
bed level, do instructions 2, 3, and 6. If
outboard edge is higher than 2”, do instructions 4 through 6.
RAISE PLATFORM
REQUIRED SHIM
WELD SIZE
THICKNESS
“W”
1”
1/16”
1/16”
2”
1/8”
1/8”
3”
3/16”
3/16”
4”
1/4”
1/4”
THIS DISTANCE (“A”)
LEVEL LINE
PLATFORM EDGE AT OR
ABOVE BED LEVEL
FIG. 15-1
EXTENSION
PLATE (REF)
2. Compare measurement “A” (FIG.
15-2) with the distances and shims
in TABLE 15-1. For example: If
measurement “A” (FIG. 15-2) is
1” below level and you want to raise
outboard edge of platform 1” above
level, use 1/8” shim to raise 2”
(TABLE 15-1).
EDGE (OUTBOARD)
EXTENSION
PLATE (REF)
VEHICLE
OUTBOARD EDGE
FLOOR (REF)
0” (LEVEL) - 2” MAX.
VEHICLE
FLOOR (REF)
“A”
LEVEL LINE
PLATFORM EDGE BELOW BED LEVEL
FIG. 15-2
SHACKLE
(REF)
TABLE 15-1
3. Weld shims (parts bag item) on both
platform stops (FIG. 15-3) to raise
outboard edge of platform to correct
position.
NEW SHIM
(TABLE 15-1)
2 PLACES
“W”
(TABLE 15-1)
WELDING SHIMS (CURBSIDE SHOWN)
FIG. 15-3
15
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
PLATFORM ADJUSTMENT
EXTENSION
PLATE (REF)
4. Compare measurement “B” (FIG.
16-1) with distances and grinding
depths in TABLE 16-1. For example:
If measurement “B” (FIG. 16-1) is 3”
above bed level and you want to lower
the outboard edge of platform to 1”
above bed level, grind 1/8” from each
platform stop (TABLE 16-1).
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
LOWER PLATFORM
EDGE (OUTBOARD)
THIS DISTANCE(“B”)
GRIND METAL
FROM PLATFORM
STOP
1”
1/16”
2”
1/8”
3”
3/16”
4”
1/4”
“B”
VEHICLE
FLOOR (REF)
LEVEL LINE
PLATFORM EDGE ABOVE BED LEVEL
FIG. 16-1
TABLE 16-1
5. Grind metal from platform stops (FIG.
16-2) to lower outboard edge of platform to correct position.
SHACKLE
(REF)
GRIND THIS FACE
(SEE TABLE 16-1)
GRINDING PLATFORM STOPS
(CURBSIDE SHOWN)
FIG. 16-2
6. Lower the platform, then raise it to bed
level. The outboard edge of platform should
be level or up to 2” maximum above bed
level (FIG. 16-3).
EXTENSION
PLATE (REF)
OUTBOARD EDGE
0” (LEVEL) - 2” MAX.
VEHICLE
FLOOR (REF)
LEVEL LINE
PLATFORM EDGE ABOVE BED LEVEL
FIG. 16-3
16
PARTS BREAKDOWN
MAIN ASSEMBLY (ALUMINUM PLATFORM)
REFER TO HYDRAULIC COMPONENTS
& PUMP BOX ASSEMBLY
3
2
REFER TO MAIN
FRAME ASSEMBLY
8B
6
8A
8C
8
7
7
4
3
1
REFER TO PLATFORM &
FLIPOVER ASSEMBLY
ITEM
QTY.
PART NO.
DESCRIPTION
1
1
226938
EYE, DROP FORGED PAD, 3/4” X 1-1/2”
2
1
227700
HOOK ASSEMBLY
3
4
900014-4
CAP SCREW, HEX HEAD, 3/8”-16 X 1” LG, GRADE 8
4
2
901011-5
NUT, HEX HEAD 3/8”-16
5
1
226355
EXTENSION PLATE
6
2
902001-2
WASHER, FLAT 3/8”
7
4
902011-4
WASHER, LOCK 3/8”
8
1
265994-01
OPENER ASSEMBLY
8A
1
030805
COTTER PIN, 1/8” X 1” LG
8B
1
280082-01
ROLLER
8C
1
905202-03
PIN
17
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
5
MAIN FRAME ASSEMBLY: GPT-25 & GPT-3
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
10B
3
5
4
6
10
2
4
4
3
12
10A
6
6
9
1
6
2
9B
6
1
2
9C
1
9A
14A
2
9B
6
9
5
6
13
1
14A
7
10
1
14
6
11
9C
9A
1
6
11
8
(6 PLACES)
18
1
6
1
10A
10B
QTY.
PART NO.
DESCRIPTION
1
8
030034
BOLT, 3/8”-24 X 1” LG
2
4
030035
BOLT, 3/8”-24 X 1-1/4” LG
3
2
040103-5
LOOM, SPLIT 1/2” X 5” LG
4
14
205780
PLASTIC TIE, 7” LG
5
2
221416
ROLL PIN, 3/8” X 2” LG
6
10
226941
LOCK NUT, 3/8”-24
7
1
050175
MAXON PLATE
8
6
207644
RIVET, 3/16” X .40” GRIP
9
2
253085-01
ROLLER PIN, ASSEMBLY
9A
1
221416
PIN, ROLL 3/8” X 2” LG
9B
1
261793-01
ROLLER
9C
1
264272
FLAT WASHER, 1-1/4” I.D. X 2-1/4” O.D.
10
2
261788-01
PARALLEL ARM
10A
2
905112-05
BEARING, SELF LUBE 1-3/8” X 1-5/8” LG
10B
2
905114-04
BEARING, SELF LUBE 1-1/4” X 1-1/2” LG
11
2
262280
PIN WELDMENT
12
1
262322-01
LIFT ARM WELDMENT, LH
13
1
262322-02
LIFT ARM WELDMENT, RH
14
1
262396
LIFT FRAME WELDMENT
14A
2
263473
ROLLER, KNUCKLE DOWN
19
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
MAIN FRAME ASSEMBLY: GPT-25 & GPT-3 - Continued
31
32
31
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
32
34
33
22
23
29
33
30
34
20
30
24
16
15
25
23
25
18A
20
28
15
16
23
22
21
18
27
29
17
19A
17
26
20
19
23
21
24
QTY.
PART NO.
DESCRIPTION
15
2
262437
BUSHING WELDMENT HOSE CLAMP
16
2
262440
PIN WELDMENT
17
2
265807-01
PIN WELDMENT, 1-3/8” X 13-1/8” LG
18
1
265815-01
SHACKLE ASSEMBLY, LH
18A
2
905112-06
BEARING, SELF LUBE, 1-3/8” X 3/8” LG
19
1
265815-02
SHACKLE ASSEMBLY, RH
19A
2
905112-06
BEARING, SELF LUBE, 1-3/8” X 3/8” LG
20
2
266035-01
PIN, WELDMENT
21
2
902011-4
LOCK WASHER, 3/8”
22
2
902013-20
FLAT WASHER, 1-1/4”
23
4
905114-04
BEARING, SELF LUBE 1-1/4” X 1-1/2” LG
24
2
905115-02
BEARING, SELF LUBE 1-1/2” X 1-1/2” LG
25
2
907026
ROLL PIN, 3/16” X 2-1/4” LG
26
1
226363-01
TORSION SPRING, RH, 1/2” X 5-3/4”
27
1
226363-02
TORSION SPRING, LH, 1/2” X 5-3/4”
28
1
281561-01
MAIN FRAME
29
2
229657
PIN WELDMENT
30
2
250310
PIN WELDMENT
31
2
281539-01
SADDLE
32
4
901024-3
HEX BOLT, 2-1/4” LG
33
4
901023
FLANGE LOCK NUT
34
2
090300-12
FLAT, 3/4” X 1” X 6” LG
21
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
MAIN FRAME ASSEMBLY: GPT-4 & GPT-5
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
18A
9
7
17
18
10
5
7
3
7
5
19
18A
14
2
16 15
10
2
17
17
17
4
3
2
1
15
13
16
2
2
12
17
4
17
16
1
9
20
17
9
14
17
1
18
17
11
6
18A
2
17
18A
9
8
(6 PLACES)
16
13
22
1
QTY.
PART NO.
DESCRIPTION
1
4
030034
BOLT, 3/8”-24 X 1” LG
2
6
030035
BOLT, 3/8”-24 X 1-1/4” LG
3
2
030038
BOLT, 3/8”-24 X 1-1/2” LG
4
2
030414
COTTER PIN, 1/8” DIA X 2-1/2” LG
5
2
040103-5
LOOM, SPLIT 1/2 X 5” LG
6
1
050175
MAXON PLATE
7
14
205780
PLASTIC TIE, 7” LG
8
6
207644
RIVET, 3/16” X .40” GRIP
9
4
221416
ROLL PIN, 3/8” X 2” LG
10
2
226358
PIN WELDMENT
11
1
226363-01
TORSION SPRING, RH, 1/2” X 5-3/4”
12
1
226363-02
TORSION SPRING, LH, 1/2” X 5-3/4”
13
2
226365
PIN WELDMENT
14
2
226368
PIN WELDMENT
15
2
226372
ROUND TUBE X 1/4” (2” X 5/16”W)
16
4
226375
ROLLER (1” WIDE, 3-1/8” O.D.)
17
10
226941
LOCK NUT, 3/8”-24
18
2
261785-01
PARALLEL ARM
18A
4
905112-07
BEARING, SELF LUBE 1-3/8” X 1-3/4” LG
19
1
262332-01
LIFT ARM WELDMENT, RH
20
1
262332-02
LIFT ARM WELDMENT, LH
23
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
MAIN FRAME ASSEMBLY: GPT-4 & GPT-5 - Continued
34
35
37
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
35
30
31
28
36
37
36
28
32
21
23
22
27
25A 31
22
23
21
24
29
31
25
33
26A
31
24
26
24
29
32
30
QTY.
PART NO.
DESCRIPTION
21
2
262435
PIN WELDMENT
22
2
262437
BUSHING WELDMENT HOSE CLAMP
23
2
262462
PIN WELDMENT
24
2
265807-01
PIN WELDMENT, 1-3/8” X 13-1/8” LG
25
1
265813-01
SHACKLE ASSEMBLY, LH
25A
2
905112-06
BEARING SELF LUBE 1-3/8” X 3/8” LG
26
1
265813-02
SHACKLE ASSEMBLY, RH
26A
2
905112-06
BEARING SELF LUBE 1-3/8” X 3/8” LG
27
1
281562-01
MAIN FRAME
28
2
266033-01
PIN WELDMENT
29
2
902011-4
LOCK WASHER, 3/8”
30
2
902013-21
FLAT WASHER, 1-3/8”
31
4
905112-07
BEARING, SELF LUBE 1-3/8” X 1-3/4” LG
32
2
905113-03
BEARING, SELF LUBE 1-3/4” X 1-3/4” LG
33
1
262397
LIFT FRAME WELDMENT
34
2
281539-01
SADDLE, LOW PROFILE HINGE
35
4
901024-3
HEX BOLT, 1/2”-13 X 2-1/4” LG
36
4
901023
FLANGE LOCK NUT, 1/2”-13
37
2
090300-12
FLAT, 3/4” X 1” X 6” LG.
25
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
PLATFORM & FLIPOVER ASSEMBLY (ALUMINUM)
2
REFER TO PLATFORM
ASSEMBLY
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
3
4
4
3
2
1
1A
ITEM
QTY.
1
1
281512-01
FLIPOVER WELDMENT, 30”
1
265819-01
HANDLE WELDMENT
2
2
263602
HINGE PIN WELDMENT
3
4
902020-1
FLAT WASHER, NYLON, 3/4” I.D., 1-5/16” O.D.
4
2
905033-2
ROLL PIN, 1/4” X 1-1/4” LG
1A
PART NO.
DESCRIPTION
26
1
REFER TO PLATFORM
ASSEMBLY
2
3
3
2
1
REFER TO FLIPOVER WITH SINGLE
CART STOP OR FLIPOVER WITH DUAL
CART STOPS (SINGLE IS SHOWN)
ITEM
QTY.
PART NO.
DESCRIPTION
1
2
263602
HINGE PIN WELDMENT
2
4
902020-1
FLAT WASHER, NYLON, 3/4” I.D., 1-5/16” O.D.
3
2
905033-2
ROLL PIN, 1/4” X 1-1/4” LG
27
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
PLATFORM & FLIPOVER ASSEMBLY WITH CART STOPS (ALUMINUM)
PLATFORM ASSEMBLY (ALUMINUM)
6
(2 PLACES)
5
9
4
1, 1A
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
3
7
(2 PLACES)
9
2
8
3
4 5
2
8
7
(2 PLACES)
6
(2 PLACES)
ITEM
QTY.
1
1
281510-01
PLATFORM ASSEMBLY, 30”
1
281508-01
PLATFORM WELDMENT, 30”
2
2
263608
HINGE BRACKET, INSIDE
3
2
263609
HINGE BRACKET, OUTSIDE
4
2
902011-6
LOCK WASHER, 1/2”
5
2
900033-9
CAP SCREW, 1/2”-20 X 2” LG
6
4
900035-10
CAP SCREW, 1/2”-13 X 3-1/2” LG
7
4
902013-13
FLAT WASHER, 1/2”
8
2
040066
LOCK NUT, 1/2”-13
9
4
260917-04
SELF LUBE BEARING, 1/2” LG
1A
PART NO.
DESCRIPTION
28
29
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
THIS PAGE INTENTIONALLY LEFT BLANK
FLIPOVER WITH SINGLE CART STOP (ALUMINUM)
16 (4 PLACES)
7
13
2
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
16 (4 PLACES)
14
8
13
9
5
10
7
(4 PLACES)
6 3
14
7
1, 1A
11
8
4
1B
4
30
11
12
6
15
QTY.
PART NO.
DESCRIPTION
1
1
281533-01
FLIPOVER ASSEMBLY SINGLE CART STOP 30”
1A
1
281513-01
FLIPOVER WELDMENT, SINGLE CART STOP
1B
1
265819-01
HANDLE WELDMENT
2
1
262508-02
SINGLE CART STOP RAMP WELDMENT
3
1
262481-02
OPENING AND CLOSING ARM, RH
4
2
262515
METAL EYELET END FITING
5
1
262513-01
PIN, 80-5/8” LG
6
2
905122-02
SELF LUBE BEARING, 1/2” X 5/16” LG
7
6
253542
SELF LUBE BEARING, 1/2” X 1/2” LG
8
2
905135
CLEVIS PIN, 5/16” X 7/8” LG
9
1
030406
ROLL PIN, 1/8” X 1” LG
10
1
262536
TORSION SPRING
11
2
030805
COTTER PIN, 1/8” X 1” LG
12
1
262514
GAS SPRING, 90 LBS
13
2
281536-01
STOP BLOCK
14
2
902022
WASHER, 1/2”
15
1
900047
SHOULDER SCREW,1/2” X 3/4” LG
16
8
903705-02
RIVET, BLIND, 1/4” X 5/8” LG
31
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
FLIPOVER WITH DUAL CART STOPS (ALUMINUM)
14
9
13
6
14
12
7
4
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
13
17 (4 PLACES)
16
5
12
4
2
11
17 (4 PLACES)
12
10
16
15
8
11
(4 PLACES)
14
1, 1A
1B
10
11
12
4
32
13
3
14
13
4
7
9
QTY.
PART NO.
DESCRIPTION
1
1
281532-01
FLIPOVER ASSEMBLY DUAL CART STOP 30”
1A
1
281513-02
FLIPOVER WELDMENT, DUAL CART STOP
1B
1
265819-01
HANDLE WELDMENT
2
1
262509-06
DUAL CART STOP RAMP WELDMENT, RH
3
1
262481-02
OPENING AND CLOSING ARM, RH
4
4
262515
METAL EYELET END FITING
5
1
262509-05
DUAL CART STOP RAMP WELDMENT, LH
6
1
262481-01
OPENING AND CLOSING ARM, LH
7
2
262514
GAS SPRING, 90 LBS
8
1
262513-01
PIN, 80-5/8” LG.
9
2
900047
SHOULDER SCREW, 1/2” X 3/4” LG
10
2
902022
WASHER, 1/2”
11
6
253542
SELF LUBE BEARING, 1/2” X 1/2” LG
12
4
905135
CLEVIS PIN, 5/16” X 7/8” LG.
13
4
030805
COTTER PIN, 1/8” X 1” LG.
14
4
905122-02
SELF LUBE BEARING, 1/2” X 5/16” LG
15
1
030406
ROLL PIN, 1/8” X 1” LG
16
2
281536-01
STOP BLOCK
17
8
903705-02
RIVET, BLIND,1/4” X 5/8” LG
33
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
DOCK BUMPER
EXTENSION PLATE
(REFERENCE)
MAIN FRAME
(REFERENCE)
5 (2 PLACES)
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
4
2
4
1
6
(2 PLACES)
7
(2 PLACES)
8
(2 PLACES)
1
5
(2 PLACES)
7
(2 PLACES)
ITEM
QTY.
PART NO.
DESCRIPTION
1
2
226856
DOCK BUMPER ANGLE X 23-1/2” LG
2
1
266019-03
BRACE ANGLE L/H
3
1
266019-04
BRACE ANGLE R/H
4
2
222988
BUMPER
5
4
900033-5
CAP SCREW, 1/2”-20 X 2” LG
6
4
901011-10
NUT, 1/2”
7
4
902000-14
FLAT WASHER, 1/2”
8
4
902011-6
LOCK WASHER, 1/2”
34
3
6
(2 PLACES)
8
(2 PLACES)
35
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
THIS PAGE INTENTIONALLY LEFT BLANK
HYDRAULIC COMPONENTS - POWER DOWN
CAUTION
If the Liftgate is equipped with a bumper (ICC-type), replacement hydraulic
hoses must be routed with sufficient clearance from the bumper. The clearance prevents the hoses from rubbing or getting caught on the bumper.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
REFER TO
PUMP ASSEMBLY
(POWER DOWN)
17
11
18
21
8
1
20
1
22
23
19
14
13
13
15
15
3
2
16
4
16
10
10
RH
6
15 9
15
12
7
5
NOTE: Replacement face seal fittings come
with required O-rings.
36
LH
1
QTY.
2
PART NO.
DESCRIPTION
266037-01
CYLINDER, 2-3/4” DIA. x 10” STROKE (GPT-25 & GPT-3)
266038-01
CYLINDER, 3” DIA. x 10” STROKE (GPT-4)
266039-01
CYLINDER, 3-1/2” DIA. x 10” STROKE (GPT-5)
2
1
265846-01
HOSE ASSY, 3/8”HP SAE#8F,#6M, 21” LG
3
1
265863-01
HOSE ASSY, 3/8”HP SAE#6- #8 F-F, 26” LG
4
1
265888-01
HOSE ASSY, 3/8”HP SAE#8 F-F, 57” LG
5
1
265888-02
HOSE ASSY, 3/8”HP SAE#8 F-F, 83” LG
6
1
265889-01
HOSE ASSY, 3/8”HP SAE#6 F-F, 55” LG
7
1
265889-02
HOSE ASSY, 3/8”HP SAE#6 F-F, 77” LG
8
1
906709-01
VALVE, FLOW REGULATOR #6 SAE, 4 GPM
9
1
905150
TEE, UNION, 3/8” FACE SEAL MALE, 6-JLO
10
2
906704-01
ELBOW, STRAIGHT THR. #8 FACE SEAL O-RING M-M
11
1
906771-01
CONNECTOR, STRAIGHT, #6 - #8, M-M, O-RING F/S
12
1
906706-01
TEE, UNION SAE#8 F/S M-M
13
2
906707-01
ELBOW, STRAIGHT THD. #6 FACE SEAL O-RING M-M
14
1
906770-01
ELBOW, MALE PIPE, #8 O-RING FACE SEAL-NPTF
15
5
906712-02
O-RING #6 (3/8” FACE SEAL TUBE-END)
16
5
906712-03
O-RING #8 (1/2” FACE SEAL TUBE-END)
17
1
050207
FITTING, SWIVEL ELBOW
18
1
226948-09
HOSE ASSY, 1/4” HP X 18-1/2” LG., M-M 1/4” NPTF
19
1
260490
NEEDLE VALVE, F-F 3/8” NPTF
20
1
800183
BUSHING, 3/8”-1/4”
21
1
906751-01
FITTING, STRAIGHT O-RING, SAE#6 M (WITH SWIVEL)
22
1
906769-01
BRANCH TEE, SWIVEL NUT, SAE#8 M-M/F
23
1
906772-01
CONNECTOR, STR. SWIVEL, #8, M-F, O-RING FACE SEAL
37
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
PUMP ASSEMBLY - POWER DOWN
CAUTION
Do not over-tighten the terminal nuts on starter solenoid. For the load
terminals, torque nuts to 40 lbs.-in. max. Torque the nuts on #10-32 control
terminals 15-20 lbs.-in.
CAUTION
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
To prevent damage when installing 2-way valves, torque valve cartridge
nut to 30 lbs.-in. max.
2
MANIFOLD
BLOCK (REF)
2C,2D
5
2A,2B
O-RING
1
SPRING
STEEL
BALL
PLUG
13
ADJUSTING
SCREW
12
SPRING
GUIDE
14
3 (4 PLACES)
6
7
4
11
8
10
9
38
QTY.
PART NO.
DESCRIPTION
REF
1
262256
PUMP ASSEMBLY, POWER DOWN
1
1
250093
MOTOR, HEAVY DUTY, 12 VDC
2
1
260275
MANIFOLD BLOCK ASSEMBLY
2A
1
260276
VALVE, 4-WAY SOLENOID
2B
1
226595
O-RING KIT, 4-WAY VALVE (NOT SHOWN)
2C
1
253353
VALVE, 2-WAY SOLENOID
2D
1
226594
O-RING KIT, 2-WAY VALVE (NOT SHOWN)
3
4
229202
CAP SCREW, HEX HEAD, WASHER HEAD (NOT SHOWN)
4
1
268026-01
WIRE ASSEMBLY, 18GA
5
1
260229
RELIEF VALVE KIT
6
1
260263
RESERVOIR, 2.5 GAL.
7
1
229193
FILLER/BREATHER CAP
8
1
260250
FILTER
9
1
290003
3-PIECE GEAR PUMP
10
1
251884
O-RING
11
1
REF. ONLY
DRIVE PLATE ASSY, 5”
12
1
260261
OIL SEAL
13
1
280404
CABLE ASSEMBLY
14
1
268030-01
SWITCH, SOLENOID (12 VDC)
39
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ITEM
PUMP BOX ASSEMBLY - POWER DOWN
2A
(LATCH)
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
2A
(LATCH)
2
1
2A
(CATCH)
3
4
REFER TO
DECALS
2A
(CATCH)
REFER TO
PUMP ASSY
ITEM
QTY.
REF
1
260157
PUMP BOX ASSEMBLY
1
1
260156
PUMP BOX WELDMENT
2
1
229383
PUMP BOX COVER
2
215139
CATCH & FASTENER
3
1
251097
RUBBER GROMMET, 7/8” I.D., 1-5/8” O.D.
4
1
093209-10
EDGE TRIM, 8-1/2” LG.
2A
PART NO.
DESCRIPTION
40
NOTE: Use switch to raise and lower Liftgate to make sure switch
operates as shown on the decal.
NOTE: MAXON recommends using dielectric
grease on all electrical connections.
RED
(TO PUMP BOX)
(FOR REFERENCESEE DECALS)
BLACK
3
GREEN
2
WHITE
1
FIG. 41-1
ITEM
QTY.
PART NO.
DESCRIPTION
1
1
264951-01
SWITCH & CABLE ASSEMBLY
2
2
900057-5
SCREW, SELF-TAPPING #10-24 X 1” LG.
3
1
905206
SWITCH BOOT SEAL
4
1
264422
CABLE ASSEMBLY, 200 AMPS, 38’ LG.
5
1
264687
KIT, MEGAFUSE (200 AMP FUSE & HEATSHRINK TUBING)
TABLE 41-1
SHORT END TO
VEHICLE BATTERY
5
4
!
LONG END TO PUMP
MOTOR SOLENOID
WARNING
Do not attach cable to battery until
Liftgate repairs are completed.
FIG. 41-2
41
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
CONTROL SWITCH AND POWER CABLE
DECALS
DECAL “H” (2 PLACES)
P/N 268308-01
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
DECAL “F”
DECAL “D”
DECAL “E”
DECAL “B”
DECAL “I”
DECAL “C”
DECAL “G”
DECAL “A”
PAINT DECAL
P/N 267338-01
PLATFORM WARNING DECAL
(2 PLACES)
P/N 281189-01
PLATFORM LOADING DECAL
(2 PLACES)
P/N 281326-01
FIG. 42-1
42
DECAL SHEET
FIG. 43-1
MODEL
DECAL SHEET P/N
DECAL “B”
GPT-25
268308-01
2500 POUNDS
GPT-3
268308-02
3000 POUNDS
GPT-4
268308-03
4000 POUNDS
GPT-5
268308-04
5000 POUNDS
DECAL SHEET
TABLE 43-1
43
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
(See TABLE 43-1)
DECALS - Continued
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
FLUID LEVEL DECAL
P/N 265330-03
FIG. 44-1
44
45
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
THIS PAGE INTENTIONALLY LEFT BLANK
SYSTEM DIAGRAMS
HYDRAULIC SCHEMATIC - POWER DOWN
HYDRAULIC CYLINDERS
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
4 GPM FLOW
CONTROL VALVE
ADJUSTABLE
NEEDLE VALVE
FILL HOLE
(PLUGGED)
PORT ARAISE VALVE “A”
PORT BLOWER
(PWR DN)
FILTER
VALVE “E”
CHECK VALVE
MOTOR
(REFERENCE)
M
PUMP
HAND PUMP
PORT
RELIEF
VALVE
(SET AT
2200 PSI)
HAND PUMP
PORT
FILTER
RESERVOIR
DRAIN HOLE
(PLUGGED)
FIG. 46-1
46
CONTROL SWITCH
RED
GREEN
BLACK
CABLE
ASSEMBLY
WHITE
SOLENOID,
VALVE A
SOLENOID,
VALVE E
MOTOR
STARTER
SOLENOID
CABLE WITH
200 AMP FUSE
BATTERY
FIG. 47-1
47
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
ELECTRICAL SCHEMATIC - POWER DOWN
TROUBLESHOOTING
PLATFORM WILL NOT RAISE
1. Connect voltmeter between motor solenoid terminal “B” and ground wires connection
on pump (FIG. 48-1). Verify that battery power is getting to “B”. Recharge the battery if
voltmeter indicates less than 12.6 volts dc.
CAUTION
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
Keep dirt, water and other contaminants from entering the hydraulic system. Before
opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up
contaminants that can get in the openings. Also, protect the openings from accidental
contamination during maintenance.
2. Do the CHECK HYDRAULIC FLUID procedure in this manual. If necessary add hydraulic fluid.
3. Touch a jumper wire to terminals “B” & “D” (FIG. 48-1). If motor runs check switch,
the switch connections, and white wire. Check and correct wiring connections or replace the switch.
4. Touch heavy jumper cables to terminals “A” & “B” (FIG. 48-1).
a. If motor runs, replace the motor solenoid.
b. If motor does not run, repair or replace the pump motor.
NOTE: In most cases, you can avoid having to manually bleed hydraulic system by
correctly positioning Liftgate platform before disconnecting any lifting cylinder high pressure hydraulic lines. The following procedure can save time and
prevent accidental fluid spills and hazards.
5. Check for structural damage and
replace worn parts.
6. Check filter in the pump reservoir.
Replace filter if necessary.
MOTOR
SOLENOID
(VOLTMETER - LEAD )
TERMINAL “A”
MOTOR (+)
7. Check if pump relief valve is dirty.
Clean if necessary or replace worn
out parts.
TERMINAL “C”
GROUND (-)
TERMINAL “B”
BATTERY (+)
FIG. 48-1
48
GROUND (-)
WIRES
CONNECTION
TERMINAL “D”
SWITCHED
BATTERY (+)
PLATFORM RAISES BUT LEAKS DOWN
GROUND (-)
WIRE
CONNECTION
MOTOR
FIG. 49-1
TERMINAL “D”
SWITCHED
BATTERY (+)
CAUTION
Keep dirt, water and other contaminants from entering the hydraulic system. Before
opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up
contaminants that can get in the openings. Also, protect the openings from accidental
contamination during maintenance.
NOTE: In most cases, you can avoid having to manually bleed hydraulic system by
correctly positioning Liftgate platform before disconnecting any lifting cylinder high pressure hydraulic lines. The following procedure can save time and
prevent accidental fluid spills and hazards.
2. Check the valve stem by removing the coil assembly (Item 1, FIG. 49-2). With platform on
ground, unscrew the valve stem (Item 2, FIG.
49-2) from the pump. Push on the plunger that
is located inside the valve stem by inserting a
small screwdriver blade in the end. If the plunger
does not move freely (approximately 1/8”), replace the valve stem. When reinstalling valve
stem, torque hex nut to 30 in-lbs.
3. Check the hydraulic cylinder. With the platform on the ground, remove the hydraulic
line from the lower port of the cylinder (FIG.
49-3). Raise the platform even with the
bed. Allow pump motor to run two seconds
more while you watch for hydraulic fluid at
the lower port. A few drops of hydraulic fluid
escaping the port is normal; however, if it
streams out, piston seals are worn. Replace
seals.
49
2
1
1/8”
FIG. 49-2
RAISE PORT
LOWER
PORT
FIG. 49-3
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
LOWERING
SOLENOID
VALVE
1. Check if lowering solenoid valve is
constantly energized. Connect voltmeter negative (-) lead to ground
(-) wires connection on pump and
positive (+) lead to terminal “D” (FIG.
49-1). If voltmeter reads battery voltage (+12.6 volts dc minimum) without
pushing the toggle switch, the control
circuit is operating incorrectly. Check if
toggle switch, wiring or coil are faulty.
PLATFORM RAISES PARTIALLY AND STOPS
CAUTION
Keep dirt, water and other contaminants from entering the hydraulic system. Before
opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up
contaminants that can get in the openings. Also, protect the openings from accidental
contamination during maintenance.
1. Lower the opened platform to the ground. Do the CHECK HYDRAULIC FLUID procedure in this manual. If necessary, add hydraulic fluid.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
2. Use voltmeter to verify the battery voltage is 12.6 volts or more.
3. Check for structural damage and poor lubrication. Replace worn parts.
NOTE: In most cases, you can avoid having to manually bleed hydraulic system by
correctly positioning Liftgate platform before disconnecting any lifting cylinder high pressure hydraulic lines. The following procedure can save time and
prevent accidental fluid spills and hazards.
4. Check the hydraulic cylinder. With the platform on the
ground, remove line from the lower port of the cylinder
(FIG. 50-1). Allow pump motor to run two seconds
more while you watch for hydraulic fluid at the lower
port. A few drops of hydraulic fluid escaping the port
is normal; however, if it streams out, piston seals are
worn. Replace seals.
5. Check filter in the pump reservoir. Replace filter if necessary.
6. Check if pump relief valve is dirty. Clean if necessary
or replace worn out parts.
50
RAISE PORT
LOWER
PORT
FIG. 50-1
LIFTGATE WILL NOT LIFT RATED CAPACITY
2. Check for structural damage or lack of lubrication. Replace worn parts.
CAUTION
Keep dirt, water and other contaminants from entering the hydraulic system. Before
opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up
contaminants that can get in the openings. Also, protect the openings from accidental
contamination during maintenance.
NOTE: In most cases, you can avoid having to manually bleed hydraulic system by
correctly positioning Liftgate platform before disconnecting any lifting cylinder high pressure hydraulic lines. The following procedure can save time and
prevent accidental fluid spills and hazards.
3. With platform on the ground, remove the pressure
hose and fitting from the pump and replace it with
a 0-3000 PSI pressure gauge. Hold the switch in
the “UP” position. Adjust the relief valve on the side
of the pump until the gauge shows 2200 PSI (FIG.
51-2). Remove guage and reinstall pressure
hose.
RAISE PORT
LOWER
PORT
FIG. 51-1
4. Check if pump relief valve is dirty. Clean if necessary or replace worn out parts.
5. Check the hydraulic cylinder. With the platform
on the ground, remove the hydraulic line from the
lower port of the cylinder (FIG. 51-1). Raise the
platform even with the bed. Allow pump motor to
run two seconds more while you watch for hydraulic fluid at the lower port. A few drops of hydraulic
fluid escaping the port is normal; however, if it
streams out, piston seals are worn. Replace seals.
RELIEF VALVE
ADJUST SCREW
PRESSURE
GAUGE
DECREASE
6. If pump cannot produce 2200 PSI or lift the load
capacity with a minimum of 12.6 volts available, the
pump is worn and needs to be replaced.
51
INCREASE
ADJUSTMENT
COVER
FIG. 51-2
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
1. Use voltmeter to verify the battery voltage is 12.6 volts or more under load from pump
motor.
PLATFORM RAISES SLOWLY
1. Connect voltmeter between motor solenoid terminal
“B” and ground (-) wires connection on pump (FIG.
52-1). Verify that battery power is getting to “B”.
Recharge the battery if voltmeter indicates less than
12.6 volts dc.
CAUTION
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
Keep dirt, water and other contaminants from
entering the hydraulic system. Before opening the
hydraulic fluid reservoir filler cap, drain plug and
hydraulic lines, clean up contaminants that can get
in the openings. Also, protect the openings from accidental contamination during maintenance.
TERMINAL “B”
BATTERY (+)
GROUND (-)
WIRES
CONNECTION
FIG. 52-1
2. Check the hydraulic cylinder. With the platform on the ground, remove the hydraulic
line from the lower port of the cylinder (FIG. 52-2). Raise the platform even with the
bed. Allow pump motor to run two seconds more while you watch for hydraulic fluid at
the lower port. A few drops of hydraulic fluid escaping the port is normal; however, if it
streams out, piston seals are worn. Replace seals.
NOTE: In most cases, you can avoid having to manually bleed hydraulic system by
correctly positioning Liftgate platform before disconnecting any lifting cylinder high pressure hydraulic lines. The following procedure can save time and
prevent accidental fluid spills and hazards.
3. Check and clean flow control valve (FIG. 52-3). When
installing flow control valve, make sure arrow on valve is
oriented as shown in FIG. 52-3.
RAISE PORT
LOWER
PORT
FIG. 52-2
FLOW CONTROL
VALVE
FIG. 52-3
52
5. Check for leaking hoses and fittings. Tighten or replace as required.
6. Check for structural damage and poor lubrication.
Replace worn parts.
7. Check the filter in the pump reservoir. Replace if
necessary.
RELIEF VALVE
ADJUST SCREW
8. With platform on the ground, remove the pressure hose and fitting from the pump and replace
it with a 0-3000 PSI pressure gauge. Hold the
control switch in the UP position. Adjust the relief valve on the side of the pump until the gauge
shows 2200 PSI (FIG. 53-1). Remove guage
and reinstall pressure hose.
PRESSURE
GAUGE
DECREASE
INCREASE
ADJUSTMENT
COVER
FIG. 53-1
53
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
4. Verify the pump motor is grounded to vehicle frame.
PLATFORM WILL NOT LOWER, LOWERS TOO SLOWLY OR TOO QUICKLY
1. Connect voltmeter between motor solenoid
terminal “B” and ground wires connection
on pump (FIG. 54-1). Verify that battery
power is getting to “B”. Recharge the battery if voltmeter indicates less than 12.6
volts dc.
LOWERING
SOLENOID
VALVE
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
2. Check for structural damage or poor lubrication. Replace worn parts.
TERMINAL “D”
SWITCHED
BATTERY (+)
3. Check if lowering solenoid valve is getting power. Connect voltmeter between
ground (-) wires connection on pump and
terminal “B” (FIG. 54-1). Push control
switch to DOWN position to energize
lowering solenoid. If voltmeter reads battery voltage (+12.6 volts dc minimum),
control circuit is operating correctly
(replace lowering solenoid). If voltmeter
reads 0 volts, check if toggle switch and
wiring are faulty.
MOTOR
TERMINAL “B”
BATTERY (+)
GROUND (- )
WIRE
CONNECTION
FIG. 54-1
CAUTION
Keep dirt, water and other contaminants from entering the hydraulic system. Before
opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up
contaminants that can get in the openings. Also, protect the openings from accidental
contamination during maintenance.
NOTE: In most cases, you can avoid having to manually bleed hydraulic system by
correctly positioning Liftgate platform before disconnecting any lifting cylinder high pressure hydraulic lines. The following procedure can save time and
prevent accidental fluid spills and hazards.
4. Check the valve stem by removing the coil assembly (Item 1, FIG. 54-2). With platform supported,
unscrew the valve stem (Item 2, FIG. 54-2) from
the pump. Push on the plunger located inside the
valve stem by inserting a small screwdriver blade in
the end. If the plunger does not move freely (approximately 1/8”) replace the valve stem.
5. Check if filtering screen on solenoid valve is
plugged. Clean carefully if required.
54
2
1
1/8”
FIG. 54-2
FLOW CONTROL
VALVE
7. Check if flow control valve (FIG. 55-1) is
pointing to the direction of restricted fluid
flow (back toward pump). If required, remove
flow control valve and install it correctly (FIG.
55-1).
FIG. 55-1
55
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
6. Check and clean flow control valve (FIG.
55-1) in the high pressure hydraulic line
connected to pump.
PLATFORM WON’T TILT DOWN TO THE GROUND
NOTE: If the Liftgate is not damaged, the adjustable flow control valve on power unit
may need to be adjusted as follows.
1. Unhook safety chain. Lower the platform until
shackles touch the ground (FIG. 56-1).
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
SAFETY
CHAIN
SHACKLE
CAUTION
SHACKLES TOUCHING
THE GROUND
FIG. 56-1
To prevent damage to adjustable flow
control valve, loosen locking screw before turning knob.
2. Open the pump box (FIG. 56-2A) to access the
adjustment knob on the adjustable flow control
valve (FIG. 56-2B).
ADJUSTABLE FLOW
CONTROL VALVE
ADJUSTMENT
KNOB
LOCKING
SCREW
UNLOCKING/LOCKING
ADJUSTMENT KNOB
FIG. 56-2B
POWER UNIT (REF)
PUMP BOX & POWER UNIT
FIG. 56-2A
3. Loosen locking screw on the flow control valve
adjustment knob (FIG. 56-2B).
56
ADJUSTABLE FLOW
CONTROL VALVE
CW TO CLOSE
VALVE
FIG. 57-1B
1/4-1/2 TURN
POWER UNIT (REF)
CCW TO OPEN &
ADJUST VALVE
FIG. 57-1C
PUMP BOX & POWER UNIT
FIG. 57-1A
5. Next, open the flow control valve a little by turning
the adjustment knob 1/4 to 1/2 turn counter-clockwise (CCW) (FIG. 57-1C).
6. Push the control switch to DOWN position. Verify
that platform tilts down to the ground (FIG. 57-2).
7. Tighten locking screw on the flow control valve
adjustment knob (FIG. 48-2B).
57
PLATFORM TILTED DOWN
FIG. 57-2
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713
4. First, close the adjustable flow control valve (FIG.
57-1A) by turning adjustment knob full clockwise
(CW) (FIG. 57-1B).
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement