Directed Electronics | 3300HS | User`s manual | Directed Electronics 3300HS User`s manual

Perfect Control Solution
System Controller SCC-3100A User’s Manual
SALES NETWORK
•
SAMSUNG TECHWIN CO.,LTD.
145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea
TEL : +82-31-740-8151~8 FAX : +82-31-740-8145
•
SAMSUNG TECHWIN AMERICA,LTD.
1480 Charles Willard St. Carson, CA 90746, UNITED STATES
TEL : +1-310-632-1234 FAX : +1-310-632-2195
•
SAMSUNG OPTO-ELECTRONICS UK,LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey Surrey KT16 OPS
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325
Thank you for purchasing a Samsung System Controller.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806-0757-01F
VAN 08. 11
ENGLISH
Contents
6
6
7
7
8
8
8
8
9
9
9
10
10
11
12
13
13
14
16
16
17
17
17
18
19
19
19
20
21
21
21
22
22
21
23
23
22
24
24
24
6. MODEL
7. TRACE
7-1. TRACE Memory
7-2. TRACE Operation
8. AF
9. OSD
DVR Mode
CONTROLLER Mode
1. Setup Mode
2. ID Setup
3. SERIAL Setup
4. DATA COPY
5. RESPONSE
5-1. SPD-3300/3000/2300 DIP Setup
5-2. SPD-2500 DIP Setup
5-3. SPD-2200 DIP Setup
5-4. SPD-1600 DIP Setup
6. PASSWORD
6-1. PASSWORD Setup
6-2. Applying Password-Setup Mode
6-3. Applying Password-Power
6-4. Entering Password
7. PRIORITY
8. DEFAULT
MATRIX Mode (SMX-25632)
1. Selection of camera and monitor
2. Joystick for Camera Controls
3. AUTO SELECT
3-1. AUTO SELECT Setup
3-2. AUTO SELECT Cancellation
3-3. AUTO SELECT Elimination
3-4. AUTO SELECT RUN/HOLD FUNCTION
4. ID SET
4-1. ID SET Setup
4-2. ID SET ON/OFF Setup
4-3. DISPLAY POSITION Setup
5. TIME/DATE SET
5-1. TIME/DATE Setup
5-2. ON/OFF Setup
5-3. DISPLAY POSITION Setup
What to do when the product malfunctions
Appearance
Controller Specifications
26
27
27
27
28
29
30
31
32
32
33
34
35
35
35
35
36
36
37
37
37
38
39
40
40
40
40
41
41
41
42
42
42
43
43
43
44
44
45
45
46
ENGLISH
4
ENGLISH
Safety caution
Major Functions and Features
1. Overview
2. Features
3. Controller Button Layout
Product Components
System Overview
1. System Connections
1-1. Connecting Controller and Junction Box
1-2. Connecting Junction Box and External Devices
2. RS-485/422 Pin Layout
3. RS-232C Pin Layout
4. Junction Box DIP Switch
5. General Connection
6. Connection Through SVR-1650/1640/950/440
Names and Functions of Each Part
1. Camera Setup Section
2. Number Pad
3. External Device Selectors
4. Universal Controller
5. DVR Controller
6. Camera Controller
7. Junction Box
PTZ Control
1. Power-On
2. Initial Screen Display
3. Camera ID Setup
4. Joystick/Camera Control Button
5. Camera Movement Speed Control
6. Camera Zoom Control
7. Camera Focus Control
PTZ Mode
1. PTZ Setup Mode
2. PRESET
2-1. PRESET Setup
2-2. PRESET Movement
3. SWING
3-1. SWING Setup
3-2. SWING Operation
4. GROUP
4-1. GROUP Setup
4-2. GROUP Operation
5. TOUR.
5-1. TOUR Setup
5-2. TOUR Operation
Safety caution
Safety caution
SYSTEM CONTROLLER
4
User’s Manual
Caution
• Use the appliance indoors only.
- Do not place the appliance outdoors or expose it to rain or moisture.
- If dropped in water, the appliance may be corroded and damaged.
• Do not use the appliance where there is excessive dust, smoke, or moisture.
- Using the appliance under such conditions may result in fire, electric shock or serious
damage.
• Do not operate the appliance in temperatures beyond those specified.
- Excessive heat or cold may damage the appliance.
- Always operate the appliance within the recommended temperature range of 0˚C ~ 40˚C.
• Do not place the appliance in direct sunlight.
- This may discolor the appliance.
• Do not apply excessive shock to the appliance.
- Excessive shock may damage the appliance.
Maintenance and Repair
If the controller body gets dirty, turn the power off and wipe the surface with a soft cloth.
- Do not use chemical agents such as alcohol or benzene. For detailed information on
upgrading the firmware, please direct your inquiries to the installation vendor.
Refer all work related to the installation of this appliance to qualified service
personnel or system installers.
For U.S.A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercialenvironment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his own expense.
SYSTEM CONTROLLER
5
User’s Manual
ENGLISH
Warning
• All work related to the installation of this appliance must be performed by qualified
service personnel or system installers.
- If the product is connected or installed improperly, electric shock, fire, severe injury, and/or
damage can result.
• Please install the product on a completely flat floor.
- Always check the strength and stability of the installation location.
- Do not drop the appliance on the floor. This may result in damage or injury.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or
covers.
- There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
• Never use the appliance in places where there are flammable materials.
- Never use the appliance in places where flammable materials such as gas are used.
• This may result in fire, explosion, and other serious accidents.
• Never touch un-insulated parts with wet hands.
- Touching un-insulated parts with wet hands may result in serious electric shock.
• Never expose the appliance to water or moisture.
- If the appliance gets wet, immediately turn the power off.
- Stop using the appliance if it gets wet. Contact the manufacturer immediately.
• Stop using the appliance if there appears to be any operational problem.
- Immediately turn the power off to the appliance if there is any abnormal condition such as
smoke or unusual smells.
- Continuing to use the appliance under abnormal conditions may result in serious damage.
• Always use the recommended power.
- Using incorrect power source ratings may result in fire, electric shock, or damage.
• Always handle the connection cable with care.
- Never damage or modify the connection cable.
- Do not pull, expose to heat, or place heavy objects on the connection cable.
- Non-observance of these warnings may result in fire, electric shock or damage.
ENGLISH
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to
provide customers with more environment-friendly products.The Eco mark
represents Samsung Techwin s will to create environment-friendly products,
and indicates that the product satisfies the EU RoHS Directive.
Major Functions and Features
ENGLISH
3. Controller Button Layout
Major Functions and Features
1. Overview
This product is designed for use only with the Speed Dome camera, CCTV receiver, and
Samsung Digital Video Recorder.
• Speed Dome camera : Samsung Techwin (SPD), PELCO-D, PELCO-P, PANASONIC (PANA),
SAMSUNG ELECTRONICS (SEC), ELMO, BOSCH
• CCTV Receiver : SRX-100B
• DVR : Samsung Techwin
• MATRIX : Samsung Techwin
Caution
• Different surveillance cameras may have different names for the same functions,
depending on the manufacturer.Some functions may not be available for certain
models.
2. Features
- It is possible to totally control the 255 Speed Dome camera, CCTV Receiver, Samsung
Matrix and Samsung Digital Video Recorder.
- If the Speed Dome is set to one-way reception (RESPONSE OFF), it is possible to connect a
maximum of 16 subcontrollers, including the master controller.
- If the Speed Dome is set to two-way reception (RESPONSE ON), it is possible to connect a
maximum of 12 subcontrollers, including the master controller.
- Camera control with the joystick, zoom buttons, and focus buttons
- Easy camera preset location setup and movement
- Camera control without an operator through automatic operation mode
The SPD-2500/1600 is set to two-way reception and the SPD-3300/3000/2300/2200 is set
to one-way reception by factory default.
If the Speed Dome (SPD-2500/2200/1600) DIP switch is set to one-way reception, each
sub-controller can be controlled independently. If it is set to two-way reception, subcontrollers cannot be controlled independently.
Sub-controllers cannot be controlled if the master controller is in use.
SYSTEM CONTROLLER
6
User’s Manual
Product Components
SCC-3100A
1
2
3
SCC-3100A Controller
Junction Box
Controller Connection Cable
Power Adaptor (DC 12V)
User's Manual
SYSTEM CONTROLLER
7
User’s Manual
System Overview
System Overview
1-1 Connecting Controller and Junction Box
1-2 Connecting Junction Box and External Devices
3.RS-232C Pin Layout (D_SUB_MALE)
[SVR-1630 connection]
[SVR-1650/1640/950/1630/430/440 connection]
* RX+ and TX+ / RX- and TX- must be shortcircuited.
[PTZ connection]
(SPD-3300/3000/2300,
SPD-2500/2200/1600)
* RX+=DATA+
RX- =DATA
• All supported SPEED DOME functions can be controlled when the PTZ camera is
connected through the SVR-1650/1640/950.
• When connecting with an SVR-1630, only SPD series PTZ cameras can be employed.
• When controlling a PTZ camera via an SVR-1630 there is a delay, and the response may be slow.
• When controlling a PTZ camera with a sub-controller there is a delay, and the response may be slow.
SYSTEM CONTROLLER
8
User’s Manual
4. Junction Box DIP Switch
• RS-485 Termination ON
• RS-422 Termination ON
• RS-485 Termination OFF
• RS-422 Termination OFF
SYSTEM CONTROLLER
9
User’s Manual
ENGLISH
2. RS-485/422 Pin Layout (D_SUB_FEMALE)
1. System Connections
System Overview
Names and Functions of Each Part
1.Camera Setup Section
ENGLISH
5. General Connection
RESET
PRESET
SWING
: Resets camera power.
: Moves camera to the preset location (see p.21).
: Continuously travels between two assigned locations
horizontally (pan) or vertically (tilt) (see p.22).
AUX 1
: Toggles the camera's external device AUX1 on and off.
GROUP : Repeats sequential surveillance of assigned preset locations
with preset movement rates and intervals (see p.23).
AUX 2
: Toggles the camera's external device AUX2 on and off.
TOUR
: Sets more than 1 group for tour and performs
continuous group action (see p.24).
AUX 3
: Toggles the lights around the camera on and off.
AF
: Sets the focus to automatic or manual after operating
the camera (see p.28).
OSD
: Displays the camera OSD menu (see p. 29).
FUNCTION: Used to perform 2 functions or more at the same
time (see p.12).
DVR
Dome Camera + DVR: 255 max.
PTZ
Dome Camera
Junction Box
Junction Box
Master Controller
Sub-Controller
(a maximum of 15
connections allowed)
CCD Camera
Remarks
: Controller Connection Cable
: RS-485/422
: Video Cable
• SVR-1630 cannot use general connection.
6. Connection Through SVR-1650/1640/950/440
PTZ
Dome Camera
Buttons supported by different manufacturers
SPD
PELCO-D
PELCO-P
PANASONIC
SAMSUNG
ELECTRONICS
ELMO
RESET
O
O
O
O
X
O
X
PRESET
O
O
O
O
O
O
O
TOUR
O
X
X
X
X
X
X
SWING
O
O(AUTO-PAN)
O(AUTO-PAN)
O(AUTO-PAN)
X
GROUP
O
X
X
O(AUTO-SEQ)
O(SCAN)
O(AUTO-SEQ)
X
AF
O
O
O
O
O
O
X
O
O
O
O
OSD
Junction Box
Junction Box
O
O
Applies only to systems with AUX 1 terminals. (SRX-100B only)
AUX 2
Applies only to systems with AUX 2 terminals. (SRX-100B only)
AUX 3
Applies only to systems with housing and receivers that support the light function. (SRX-100B only)
Caution
Sub-Controller
(a maximum of 15
connections allowed)
SYSTEM CONTROLLER
O
AUX 1
SVR-1650/1640/950/440 : 255 max.
Master Controller
O(AUTO-SCAN) O(AUTO-SCAN)
BOSCH
PTZ
Dome Camera
10 User’s Manual
• Some buttons in the camera setup section may not be supported or may be
used differently depending on the camera manufacturer.
SYSTEM CONTROLLER
11 User’s Manual
Names and Functions of Each Part
Names and Functions of Each Part
0~9
: Used for entering camera ID, channel number,
monitor number, DVR ID, etc. (see p.26).
MONITOR : Select a monitor for matrix output
CAMERA : Enter camera number and press the CAMERA
button to set the camera ID (PTZ mode) or set the
channel (DVR mode).
SPD
F+1
TRACE RUN
F+2
TRACE MEMORY
F+3
F+4
F+5
F+6
F+7
PELCO-D
PELCO-P
PANASONIC
SAMSUNG
ELECTRONICS
TRACE RUN
TRACE RUN
TRACE RUN
TRACE RUN
(PATTERN)
(PATTERN)
(PATTERN)
(PATTERN 1)
F2
TRACE RUN
(SPECIAL 2)
(PATTERN 2)
TRACE MEMORY
F3
STOP
ELMO
BOSCH
TRACE RUN
(PATTERN 3)
AUTO POWER
AUTO-SORT
ON
AUTO POWER
OFF
SRX-100B
POWER ON
SRX-100B
POWER OFF
Caution
• When using functions that are performed by a combination of the function
button and numeric keys, the setup may be different depending on the camera
manufacturer.
• Use the AUTO POWER ON setting to allow the camera to resume the tasks in its
memory upon power supply, even if they were previously aborted as a result of
power failure, etc.
SYSTEM CONTROLLER
12 User’s Manual
3.External Device Selectors
PTZ
MATRIX
DVR
SETUP
: Selects the PTZ mode (see p.20~29).
: Selects the MATRIX mode(see p. 40~44)
: Selects the DVR mode(see p. 30)
: Activates the system setup menu(see p. 27)
4. Universal Controller
ZOOM W/T : Performs camera zoom action (wide and
telephoto).
FOCUS -/+ : Used for manual focus adjustment.
: Used for moving the menu cursor up (when menu
is active), pausing DVR playback, or playing stills.
: Used for moving the menu cursor down (when
menu is active) or stopping DVR playback.
: Used for moving the menu cursor left (when
menu is active) or playing recorded video in the reverse direction.
: Used for moving the menu cursor right (when menu is active) or Fast Playback.
: Used for playing recorded video.
ESC
: canceling entered values, or moving to the previous stage.
ENTER
: Used for executing the entered values and performing setups (PTZ mode and DVR mode)
Note
• The ESC/ENTER button is used for IRIS control of types of ELMO and BOSCH.
SYSTEM CONTROLLER
13 User’s Manual
ENGLISH
ENGLISH
2. Number Pad
Names and Functions of Each Part
STATUS
SEARCH
REC
MENU
MULTI
AUTO
ALRAM RESET
PIP
DVR FUNCTION
DIGITAL ZOOM
COPY
RELAY
LIVE / PLAY BACK
+
: The Quick Setup menu is displayed in the
DVR monitor.
: The current DVR status is displayed in the
DVR monitor.
: Used for searching the DVR recording list.
: Used to start recording the surveillance
screen.
: The DVR menu is displayed in the DVR
monitor.
: Used for switching the DVR monitor from
single screen playback mode to multiple
screen playback mode.
: displays the sequence of cameras
connected to the DVR on the monitor.
: Used for resetting the alarm and event display, turning the relay on and
off, and closing the event notification window.
: Used for performing the PIP (Picture In Picture) function.
: Used for displaying DVR (SVR-1650/1640/950) function menu.
: Used for zooming in the monitor screen when in single screen playback
mode.
: Used for copying, backing up, or deleting saved video.
: Used for manual control of replay output. (only SVR-1630)
: Used for toggling the surveillance screen and playback screen.
(only SVR-430)
: Used for decreasing menu values in detailed setup menus
: Used for increasing menu values in detailed setup menus
SVR-1650
SVR-1640
SVR-950
QUICK SET
O
O
O
O
STATUS
O
O
O
O
SEARCH
O
O
O
O
SVR-430
SVR-5416/5116
SVR-440
O
O
O
O
FOCUS O
O
O
O
O
O
O JOG
O
O
O
O
O
O
O
O
O(Play back)
O
O
O
O
O
O
O
O
O
O
O
O
O JOG
O
O
ENTER
O
O
O
O
O
ESC
O
O
O
O
O
REC
O
O
O
Record function for
Record function for
MENU
O
O
O
O
O
MULTI
O
O
O
O
O
O
FOCUS +
O
Surveil ance (LIVE) screen Surveil ance (LIVE) screen
O
O
O
O
O
AUTO
O
O
O
O
O
O
ALARM RESET
O
O
O
O
O
O
DVR FUNCTION
O
O
O
PIP
O
O
O
DIGITAL ZOOM
O
O
O
O
O
COPY
O
O
O
O
O
O
O
O
O
LIVE/PLAY BACK
O
RELAY
-/+
Caution
SVR-1630
O
O
O
O
Caution
• If your DVR model is not listed on the table, please refer to the additional
description of STW web site and DVR manual.
• DVR Model "S-DVR" is chosen in case of new SAMSUNG TECHWIN DVR model.
• DVR MODEL "P-DVR" is selected when you use Samsung Techwin's PC-Type
DVR model.
SYSTEM CONTROLLER
14 User’s Manual
• Some DVR controller buttons may not be supported or may be used differently
than as described in this manual, depending on the DVR model. Please refer to
the table below for the buttons supported by major DVR model manufacturers.
The DVR button with multiple functions works in the same way on the controller.
SYSTEM CONTROLLER
15 User’s Manual
ENGLISH
Buttons supported by different manufacturers
5. DVR Controller
QUICK SET
Names and Functions of Each Part
Names and Functions of Each Part
1. Power-On
Joystick : Used for moving the camera up, down, left, and right, and for zoom control (see p.18).
1) Tilt up (Up button)
: Moves the camera up.
2) Tilt down (Down button) : Moves the camera down.
3) Tilt left (Left button)
: Moves the camera left.
4) Tilt right (Right button) : Moves the camera right.
5) Turn stick clockwise
: Performs telephoto-zoom.
6) Turn stick counter-clockwise : Performs wide zoom.
ESC(PTZ) : Same as ESC in SPEED DOM OSD MENU.
ENTER(PTZ) : Same as ENTER in SPEED DOM OSD MENU.
7. Junction Box
[Back]
PTZ/DVR Connector
Sub-Controller
Connector
MATRIX Connector
Junction Box Connector
SYSTEM CONTROLLER
2. Initial Screen Display
3. Camera ID Setup
DIP Switch
Power Input
Connector
[ power button ]
CAM ID : Shows the currently selected camera ID.
Default is 1.
SPD
: Shows the currently selected camera model
name. Default is SPD.
MONITOR : Shows the currently selected monitor.
Default is 1.
[- - -]
: Shows the numbers (ID) entered when entering numbers with the number pad.
ID
: Shows the current controller ID. If the ID is 1, it acts as the master controller. If the ID is 2
or higher, it acts as a sub -controller. Sub-controllers cannot be used independently
without a master controller.
• Always assign a unique ID to ensure that the controller IDs do not conflict with each other.
• SPD : Samsung Techwin Co., Ltd.
[ Joystick ]
[Front]
Power on the connected external devices before turning the controller on.
Press the power button at the back of the controller to power on the controller.
The [SYSTEM Controller] message and F/W version will be displayed
in the LCD monitor, and the message will disappear when the
controller is ready for use.
• The [JOYSTICK ERROR] error will be displayed in the LCD monitor if
the joystick is not placed in the center during power-on.
ENGLISH
6. Camera Controller
PTZ CONTROL
16 User’s Manual
Enter a number using the number pad.
The number entered will be shown in the [- - -] display.
Press the CAMERA or ENTER button to set the camera ID
with the number entered.
• Any number from 1 to 255 can be selected. If the number
entered is not within the selectable range, the last entered
number is taken as the first number.
SYSTEM CONTROLLER
17 User’s Manual
PTZ CONTROL
PTZ CONTROL
5. SPEED DOME OSD Menu Control
The joystick can be used to control the camera s left and right (pan) and up and down
(tilt) movements.
ENGLISH
4. Joystick/Camera Control Button
This is the ENTER/ESC button for SPEED DOME OSD
MENU
ESC : ESC button for PTZ CAMERA OSD menu.
ENTER : ENTER button for PTZ CAMERA OSD menu.
Remarks
• Press the Esc (PTZ)/Enter (PTZ) button for 2 sec. or longer, then let go to adjust
the movement speed of the camera manually.
• The Esc button must be pressed again after setting the movement speed.
6. Camera Zoom Control
Press the ZOOM W/T button to control zoom wide
and zoom telephoto.
ZOOM W : Zoom Wide
ZOOM T : Zoom Telephoto
[ZOOM W/T button]
7. Camera Focus Control
The joystick can be used to control camera zoom functions.
Press the FOCUS -/+ button to control camera focus.
FOCUS - : Focus gets nearer.
FOCUS + : Focus gets further.
• The FOCUS -/+ button can be used as the ESC/ENTER
function in the OSD menu for older SPD series
[ Camera wide zoom ]
SYSTEM CONTROLLER
[ Camera telephoto zoom ]
18 User’s Manual
SYSTEM CONTROLLER
19 User’s Manual
[FOCUS -/+ button]
PTZ Mode
PTZ Mode
Press the SETUP button on the initial screen to display
the [SETUP SYSTEM] menu.
button to activate the [
This menu is for setting the camera to move to preset locations.
2-1. PRESET Setup
]
At the [PTZ SETUP 1 ] menu, press the 1 button
(see p.21).
Use the joystick or camera control button (SCC-3100
model) to move the camera to the desired location
(move up, down, left, and right, and control zoom).
PTZ SETUP
Enter a preset number.
Press the Enter button to assign the number to the
current location.
Press the 1 button to activate the [PTZ SETUP 1
menu.
Press the
2] menu.
2. PRESET
2-2. PRESET Movement
In the initial screen, enter an assigned preset number.
The selected number will be shown in the [- - -] display.
Reference
The menu may be different depending on the PTZ camera model.
Menu
PRESET
Models supported
Menu
SPD series, PELCO-D/P, PANASONIC,
MODEL
SAMSUNG ELECTRONICS, ELMO, BOSCH
Models supported
SPD series, PELCO-D/P, PANASONIC,
Press the Preset button to move the camera to the preset location.
If the number entered is not within the selectable range, the last entered number is
taken as the first number.
PRESET select range: 1~255
PRESET 255 may not be supported depending on the type of camera. (See the camera
manual for more information.)
Preset setup is also available in the OSD menu of the connected camera.
SAMSUNG ELECTRONICS, ELMO, BOSCH
SWING
SPD series
TRACE
GROUP
SPD series
AF
TOUR
SPD series
-
SPD series, PELCO-D/P,
PANASONIC
SPD series, PELCO-D, PANASONIC,
SAMSUNG ELECTRONICS
-
• Press the ESC button to move to an upper setup mode.
SYSTEM CONTROLLER
20 User’s Manual
SYSTEM CONTROLLER
21 User’s Manual
ENGLISH
This menu is for setting up the PTZ camera function. It is impossible to operate Speed
Dome and DVR by sub-controllers when the master controller is set to on.
ENGLISH
1. PTZ Setup Mode
PTZ Mode
PTZ Mode
4. GROUP
This menu is for setting the camera to alternate between two assigned locations
horizontally (pan) or vertically (tilt). Setting the SWING SETUP menu by controllers is only
possible in the SPD series. In case of products by other manufacturers, the setting has to be
done by the OSD menu of the camera. See the camera manual for more information.
This menu is for setting repeated sequential surveillance of assigned locations with
assigned speed and intervals. Setting the GROUP SETUP menu by controllers is only
available for an SPD series. In case of products by other manufacturers, the setting has to
be done by the OSD menu of the camera. See the camera manual for more information.
3-1. SWING Setup
4-1. GROUP Setup
At the [PTZ SETUP 1 ] ] menu, press the 2 button
(see p.19).
Press the 1 or 2 button to select a horizontal (pan) or
vertical (tilt) cycle.
Set starting point, ending point, movement speed,
and stop time.
- /
button: Moves between items.
- 1ST : Camera Preset ID for Starting point.
- 2ND : Camera Preset ID for Ending point.
- SPEED : Movement speed. Can be set for 1 ~ 64.
- STOP : Stop time at the starting point and ending point. Can be set to 1 ~ 99 (seconds).
Press the ENTER button to finish the setup (takes 2 or 3 seconds to finish).
• The Swing function cannot be set if an unassigned number or a number outside the
selectable range is entered.
• Over 2 PRESET locations have to be set before setting SWING.
At the [PTZ SETUP 1 ] menu, press the 3 button
(see p.20).
Enter a Group number.
• Any number between 1 and 6 can be selected.
Set each location's Preset ID, area movement speed,
and stop time.
- /
button: Moves between items.
- NO
: Setup sequence. Up to 64 can be selected.
- PRESET : Camera Preset ID for assigned location.
- SPEED : Area movement speed. Can be set from 1 ~ 64.
- STOP : Stop time at the starting point and ending point. Can be set to 1 ~ 99 (seconds).
Press the ENTER button to move to the setup page for the next location.
Press the Group button to finish the Group Setup.
• The Group function cannot be set if an unassigned number or a number outside the
selectable range is entered.
• Over 2 PRESET locations have to be set before setting GROUP.
3-2. SWING Operation
At the initial screen, press the Swing button.
Press the 1 and 2 buttons to perform the Swing function.
- 1 button: Performs the horizontal cycle (pan).
- 2 button: Performs the vertical cycle (tilt).
• Move the joystick or press a controller button during the Swing operation to stop the operation.
SYSTEM CONTROLLER
22 User’s Manual
4-2. GROUP Operation
At the initial screen, press the Group button.
Press the Group button to execute the operation.
The Group function is performed.
SYSTEM CONTROLLER
23 User’s Manual
ENGLISH
3. SWING
PTZ Mode
PTZ Mode
ENGLISH
5. TOUR
This menu is for setting one or more Groups for Tour so that continuous Group
operations can be carried out. The TOUR SETUP menu is only available for an SPD
series.
5-1. TOUR Setup
At the [PTZ SETUP 1
(see p.21).
] menu, press the 4 button
Press a Group number to add to the Tour.
• Up to 6 Groups can be added.
Press the ENTER button to finish the setup.
5-2. TOUR Operation
At the initial screen, press the Tour button.
The Tour function is performed.
• The TOUR operation is only available for an SPD series.
SYSTEM CONTROLLER
24 User’s Manual
SYSTEM CONTROLLER
25 User’s Manual
PTZ Mode
PTZ Mode
7. TRACE
This menu is for setting the PTZ camera ID and camera type.
At the [PTZ SETUP 1
(see p.21).
] menu, press the
button
Press the 1 button to move to the Model Setup screen.
This menu is for inputting camera movements, through joystick or camera control
buttons, into the memory for a certain period of time, to allow repeating of stored
movements when performing the Trace (PATTERN) function.
Setting the TRACE SETUP menu by controller is only available for an SPD series.
In case of products by other manufacturers, the setting has to be done by the OSD
menu of the camera. See the camera manual for more information.
7-1. TRACE Memory
Press a number in the number pad to set the PTZ camera ID.
The camera model type saved in EEPROM is displayed on the LCD monitor when changing
camera ID.
At the [PTZ SETUP 1 ] menu, press the
button
(see p.20).
Press the 2 button to move to the Trace Setup screen.
Press the 1 button.
When entering '1'
Press the + and - buttons on the number pad to change the camera type.
Press the ENTER button to finish the setup.
Use the joystick or camera control buttons to perform
the camera movement to input. Allowed movements
are horizontal movements (pan), vertical movements
(tilt), zoom, and focus controls.
Press the ENTER button to stop camera movement input.
• Maximum length for movement memory is approximately 60 ~ 105 seconds. This may
vary according to free memory space.
• Movement memory length may be shorter if the camera movement is more complicated.
• Press the FUNCTION button and the 2 button to start TRACE memory.Press the FUNCTION
button and the 3 button to stop TRACE memory. For more information, see p.12
7-2.TRACE Operation
At the Trace Setup screen, press the 2 button.
SYSTEM CONTROLLER
26 User’s Manual
SYSTEM CONTROLLER
27 User’s Manual
ENGLISH
6. MODEL
PTZ Mode
PTZ Mode
9. OSD
This menu is for adjusting camera focus manually or automatically after camera
operation. If AF is set to OFF in the camera setup menu, set the AF of the controller to
ON and then automatic adjustment is performed after camera operation.
At the [PTZ SETUP 1
(see p.21).
] menu, press the
button
This is used for displaying the camera menu on the monitor.
Press the OSD button from the PTZ or DVR mode. (Warning: Execute only from the Master
controller).
Use the controller buttons to set up the camera menu.
- OSD
Press the 3 button to move to the AF Setup screen.
Press the 1 button to automatically adjust the focus
after camera operation. Press the 2 button to disable
automatic focus adjustment after camera operation.
• Auto Focus Setup is also available in the OSD menu
of the camera connected.
• It is recommended that you set up the AF function
through the camera OSD menu.
: SPD- Toggle camera menu on/off (hold down for 2 seconds)
PELCO-D - Toggle camera menu on/off
PELCO-P - Toggle camera menu on/off (press(ESC(PTZ))
PANASONIC - Toggle camera menu on/off (press ESC(PTZ))
Samsung Electronics - Toggle camera menu on/off (press ESC(PTZ))
ELMO - Toggle camera menu on/off
BOSCH - Toggle camera menu on/off (press(ESC(PTZ))
- ESC(PTZ) : Cancels the menu selection.
- ENTER(PTZ) : Selects the menu.
: Moves the menu cursor right.
only Samsung
techwin, Panasonic,
: Moves the menu cursor left.
Samsung
: Moves the menu cursor up.
Electronics,
ELMO model
: Moves the menu cursor down.
- Joystick : Use the joystick to move the menu cursor up,
down, left, and right.(Panasonic and ELMO are not
supported.)
• Joystick or other button inputs cannot be used for camera operation when the camera
menu is displayed on the monitor.
• PRESET, SWING, GROUP, and TRACE functions can be set in the OSD menu of the camera.
• Please refer to the camera manual for more information on the camera menu.
SYSTEM CONTROLLER
28 User’s Manual
SYSTEM CONTROLLER
29 User’s Manual
ENGLISH
8. AF
DVR Mode
Contents
Model
SVR-5416/5116
This menu is for setting the DVR ID and model for
operation by a controller. Sub-controllers cannot be
used if the master controller is in Setup mode.
• To connect to the SVR-5416/5116: System Remote Controller setup Serial (RS232/RS485)
check on
Serial setup
Communication Port 1/Equipment Number setup (Port setting must
be identical to controller’s communication settings. Default (9600, 8, N, 1))
Controller Mode
Press the SETUP button on the initial screen to display the
[SETUP SYSTEM] menu.
1. Setup Mode
Press the 2 button to activate the [DVR SETUP] menu.
Press the SETUP button on the initial screen to display the
[SETUP SYSTEM] menu.
Press the 1 button to activate the [DVR Model SETUP] menu.
Press a number on the number pad to set the DVR ID.
The DVR model name saved in EEPROM will be
displayed on the LCD monitor when changing DVR ID.
Press the + and - buttons to change the DVR model name.
When entering '1'
Press the 3 button to activate the [CONTROLLER
SETUP 1 ] menu.
Press the ENTER button to finish the setup.
Model
SVR-1650/1640/950
SVR-1630
SVR-430
Contents
• When connecting to an SVR-1650/1640/950, the SYSTEM ID must set equal to the Controller
DVR ID (Menu Network RS422/485 SYSTEM ID).
• When connecting the SVR-1650/1640/950 to the controller, use Port A on the left of RS422/485
located on the back side. Port B is for SPEED DOME connection. For RS485 connection, press the
TERM switches 1 & 2 down to the ON position (located next to the RS422/485 PORT).
It unifies the model of the SVR-1650/1640/950/440 with the SVR-1650.
• When connecting to an SVR-1630, the SVR-1630 keyboard control address must be set to be the
same as the controller DVR ID (Menu System Setup Misc.).
• For the SVR-1630 COM2 RS422/485 menu (Menu System Setup Serial Port), Device must be set
to SCC-3000 and Interface to RS-485, and for the COM4 RS422/485 menu (Menu System Setup
Serial Port), Device must be set to SPD2500 (if an SPD2500 is connected) and Interface to RS-485.
• When controlling a PTZ camera via an SVR-1630, connect the SVR-1630 and the controller to
COM2 RX+/RXand connect the SVR-1630 and PTZ camera to COM4 RX+/RX-. Also, at the SVR1630 channel setup menu, set the PTZ port of each channel to COM4 and set the PTZ address to
be the same as the PTZ camera ID.
• When connecting to an SVR-430, the SVR-430 system ID must be set to be the same as the
controller DVR ID (Menu Network/Communication RS422/485 SYSTEM ID).
SYSTEM CONTROLLER
30 User’s Manual
Press the
button to activate the [
SETUP 2 ] menu.
CONTROLLER
Press the
button to activate the [
CONTROLLER SETUP 3] menu.
At the [CONTROLLER SETUP 1 ], [ CONTROLLER
SETUP 2 ] or [ CONTROLLER SETUP 3] menu, press a menu number to open a setup
menu.
Reference
• Press the ESC button to move to the upper setup mode.
• The Controller Setup menu can be added to enhance controller functionality.
SYSTEM CONTROLLER
31 User’s Manual
ENGLISH
DVR MODEL Setup
Controller Mode
4. DATA COPY
This menu is for setting controller ID.
At the [Controller SETUP 1 ] menu, press the 1 button
(see p.31).
Press a number on the number pad to enter a controller ID.
Press the ENTER button to set the controller ID.
• Assign number 1 for setting the controller ID for the
master controller.
• The lower the ID number, the higher the controller priority.
• Sub-controllers can be operated only when
connected to a master controller; Sub-controllers cannot be operated independently.
This menu is for copying master controller menu data to a sub-controller.
The controller ID value is not copied.
At the [CONTROLLER SETUP 1
button (see p.31).
] menu, press the 3
Press a number on the number pad to enter the ID number
for the subcontroller where the data will be copied.
Press the ENTER button to set the controller ID.
Press the 1 button to start coping data.
Press the 2 button to return to the previous menu.
3. SERIAL Setup
This menu is for setting the serial port for connecting external devices to the controller.
At the [CONTROLLER SETUP 1 ] menu, press the 2
button (see p.31).
Press the 1 button to activate the Serial 1 PORT Setup screen
(PTZ camera/DVR connection PORT). Press the 2 button to
activate the Serial 2 PORT Setup screen (reserved PORT).
• The value displayed at step indicates the current
setup value.
• The BAUD RATE/ DATA BIT/ STOP BIT/ PARATY BIT
for PORT 2, which connects to the sub-controller, are fixed and cannot bechanged.
The PORT Setup screen will be displayed. Press the
number for a setup menu.
1: Sets the BAUD RATE. (4800, 9600, 19200, 38400)
2: Sets the DATA BIT. (8BIT, 7BIT)
3: Sets the STOP BIT. (1BIT, 2BIT)
4: Sets the PARITY BIT. (NONE, ODD, EVEN)
• Default values for controller SERIAL are 9600 (BAUD RATE), 8BIT (DATA BIT), 1BIT (STOP
BIT) and NONE (PARITY BIT).
SYSTEM CONTROLLER
32 User’s Manual
The [DATA COPYING SUCCESS] message appears when data copying is complete.
The [DATA COPYING FAIL] message appears if data copying failed.
[DATA COPY SUCCESSFUL]
[DATA COPY FAILURE]
• Data copy takes approximately 7~10 seconds.
This menu is available only for the master controller (ID: 1).
SYSTEM CONTROLLER
33 User’s Manual
ENGLISH
2. ID Setup
Controller Mode
Controller Mode
Controller Mode
This menu is for setting RESPONSE function of the camera which is connected Controller.
At the [CONTROLLER SETUP 1 ] menu, press the
button (see p.31).
Press the 1 button to open the Response Setup screen.
Press the 1 button to set the controller RESPONSE
setting to ON. The controller automatically restarts to
apply the change.Press the 2 button to set the
controller RESPONSE setting to OFF. The master
controller display shows the setup screen for the
number of the connected subcontroller.
Press the 1 ~ 4 button to set the number of the desired
sub controller. The controller automatically restarts to
apply the changed settings after entering the number.
- 1: Sets the number of sub-controllers to 4 including
the master controller.
- 2: Sets the number of sub-controllers to 8 including
the master controller.
- 3: Sets the number of sub-controllers to 12 including the master controller.
- 4: Sets the number of sub-controllers to 16 including the master controller.
• Set the maximum number of sub-controllers, to shorten the sub controller data loading time
by making the master controller memorize the number of sub-controllers.
• If Response is set as ON, a maximum of 12 sub-controllers only can be selected.
5-1. SPD-3750T/3750/3350 DIP Setup
SW2- #8
RESPONSE Setup
ON
OFF
Response
No Response
5-2. SPD-3300/3000/2300 DIP Setup
SW3- #1
RESPONSE Setup
ENGLISH
For information on camera RESPONSE settings (DIP switch settings), refer to the camera manual.
5. RESPONSE
5-1. SPD-3300/3000/2300 DIP Setup
DIP-SW 1
DIP-SW 2
DIP-SW 3
DIP-SW 4
DIP-SW 5
DIP-SW 6
DIP-SW 7
DIP-SW 8
RESPONSE Setup
Termination setting
Communication method
Factory regulation
PC Communication
ON
HALF DUPLEX
OFF
FULL DUPLEX
Refer to the camera user manual
RS-422
RS-485
Always OFF
RS-232Communication OFF
5-2. SPD-2500 DIP Setup
ON
OFF
Response
No Response
ON
DIP-SW 1
Not used
DIP-SW 2
Reserved
DIP-SW 3
RESPONSE Setup
DIP-SW 4
Factory default
OFF
Always OFF
Always OFF
HALF DUPLEX
FULL DUPLEX
Always OFF
[RESP
5-3. SPD-2200 DIP Setup
5-3. SPD-1000 DIP Setup
DIP-SW 1
DIP-SW 2
ON
SW2- #6
RESPONSE Setup
Response
OFF
No Response
DIP-SW 3
RESPONSE Setup
ON
OFF
HALF DUPLEX
FULL DUPLEX
Reserved
Always OFF
Termination setting
Refer to the camera user manual
DIP-SW 4
[RESP
Caution
• If the camera RESPONSE is set to two-way reception (RESPONSE ON), the controller
RESPONSE menu must be set to ON. If the camera RESPONSE is set to one-way reception
(RESPONSE OFF), the controller RESPONSE menu must be set to OFF.If this is not followed,
the system may have a configuration conflict. For more information on the camera RESPONSE
settings, direct your inquiries to the installation vendor. If the DIP switch for the camera
connected to the controller is set to two-way reception (RESPONSE ON), this menu can be
used to set up the RESPONSE value for the controller and the number of sub-controllers.
SYSTEM CONTROLLER
34 User’s Manual
[RESP
5-4. SPD-1600 DIP Setup
ON
DIP-SW 1
SYSTEM CONTROLLER
35 User’s Manual
Not used
DIP-SW 2
Reserved
DIP-SW 3
RESPONSE Setup
DIP-SW 4
Factory default
OFF
Always OFF
Always OFF
HALF DUPLEX
FULL DUPLEX
Always OFF
[RESP
Controller Mode
Controller Mode
This menu is for setting the password to enter when changing controller setup values
upon power-on.
At the Password Setup screen, press the 2 button.
6-1. PASSWORD Setup
At the [CONTROLLER SETUP 1 ] menu, press the
button (see p.31).
Press the 2 button to activate the Password Setup
screen.
Press the 1 button to ask for a password every time the
setup mode is selected. Press the 2 button to skip asking
for a password.
6-3. Applying Password - Power
Press the 1 button to activate the Password Setup
screen.
At the Password Setup screen, press the 3 button.
Use the number pad to enter a 6-digit password.
Press the 1 button to ask for a password every time the
appliance is powered on. Press the 2 button to skip asking
for a password.
The password verification screen will appear.
Re-enter the same password. The password will be
saved.
Caution
6-4. Entering Password
If a password is set, the password has to be entered every
time the appliance is powered on or before entering the
setup menu. At the screen as illustrated on the right, enter
the password set at step (6-1).
• The factory default password is 000000.
Please change the password after installation.
SYSTEM CONTROLLER
36 User’s Manual
SYSTEM CONTROLLER
37 User’s Manual
ENGLISH
6-2. Applying Password - Setup Mode
6. PASSWORD
Controller Mode
Controller Mode
8. DEFAULT
This menu is for setting the connected sub-controller to use a PTZ camera or DVR within
the specified restrictions. This menu is available for master controller (ID: 1) only.
At the [CONTROLLER SETUP 1 ] menu, press the
button twice. (see p.31).
Press the 1 button to activate the Priority Setup
screen.
Press the 1 button to change the controller setup
values to the default values and restart the controller.
Press the 2 button to cancel the process.
Press the 1 button to activate the PTZ Camera
Restriction Setup menu.
Press the 2 button to activate the DVR Restriction
Setup menu.
Use the controller button to set the menu.
[ID]: ID of the assigned sub-controller.
Left [000-255] : The currently selected restriction ID.
Right [000-000] : ID to be assigned.
- /
: Moves items left and right.
- 2 ~ 16 : Enters ID number.
- ESC : Moves to the upper menu.
- ENTER : Finishes setup.
SYSTEM CONTROLLER
This menu is for resetting the changed controller setup values to the default values.
At the [CONTROLLER SETUP 1 ] menu, press the
button twice. (see p.31).
Press the 2 button to open the Default Setup screen.
[PTZ Camera Restriction Setup Menu]
[DVR Restriction Setup Menu]
38 User’s Manual
SYSTEM CONTROLLER
39 User’s Manual
ENGLISH
7. PRIORITY
MATRIX Mode
MATRIX Mode
1. Selection of Camera and Monitor
Select a number between 1 and 255, and then press
the CAMERA button to select the corresponding
camera.
This is a manual function to display the cameras connected to the MATRIX SYSTEM on the monitor.
Select Monitor : Select a monitor number between 1 and 32. Press MONITOR.
Select Camera : Select a camera number between 1 and 255. Press CAMERA.
• Monitor must be selected before the camera. Default is 1, and up to 255 cameras can be
selected by connecting up to 3 input MATRIX extensions.
2. Joystick for Basic Camera Controls
JOYSTICK : Used for moving the PAN/TILT up/down/left/right/diagonal.
ZOOM
: Use the TELE button for Telephoto view
(Turn the TELE button or the Joystick clockwise for Telephoto view)
Use the WIDE button for WIDE view
(turn the WIDE button or the Joystick counterclockwise for WIDE view)
FOCUS : + button to focus away
- button to focus closer
Select a number between 1 and 60, and then press
the ENTER button to select the corresponding HOLD
TIME.
3-2 Cancel AUTO SELECT
This is a function to cancel AUTO RUN
Press the MENU button, and then press the 1 button.
(In MATRIX, wait for data loading completion.)
Press the ESC or the SET button to exit the
corresponding setting.
3-3. Delete AUTO SELECT
This is a function to delete each AUTO RUN setting.
3. AUTO SELECT
3-1. AUTO SELECT Setup
This is a function to select cameras to be displayed on the monitor in AUTO RUN.
From the initial screen, press the MATRIX button and
then press the MENU button to display the [MATRIX
CONTROL] menu.
Press button 1 to display the [AUTO SELECT SET]
menu. (In MATRIX, wait for data loading completion.)
Select a number between 1 and 32, and then press the
ENTER button to select the corresponding monitor.
SYSTEM CONTROLLER
40 User’s Manual
Press the MENU button, and then press button 2.
Select a number between 1 and 32, and then press
the ENTER button to select the monitor to be
canceled.
3-4. AUTO SELECT RUN/HOLD
Press the AUX2 button to RUN all MATRIX channels.
Press the AUX3 button to HOLD all MATRIX channels.
Select a number between 1 and 32, and then press the AUX2 button to RUN the
corresponding MATRIX channel.
Select a number between 1 and 32, and then press the AUX3 button to HOLD the
corresponding MATRIX channel.
SYSTEM CONTROLLER
41 User’s Manual
ENGLISH
MATRIX is another name for SAMSUNG SMX-25632.
MATRIX Mode
MATRIX Mode
This is a function to enter text on the corresponding
camera.
[MATRIX screen]
4-1 Select ID SET
From the initial screen, press the MATRIX button, and
then press the MENU button to display the [MATRIX
CONTROL] menu.
Press button 3 to display the [CAMERA ID SET] menu.
(In MATRIX, wait for data loading completion.)
Move the joystick to select the ID CHANGE SET from the
MATRIX screen, and then press the “FOCUS +“ button.
[MATRIX screen]
Move the joystick up/down to change letters or
numbers, use the joystick's ZOOM to change letters/numbers/vowels/consonants.
Press the “FOCUS +“ button to save.
4-2. Setting ID SET ON/OFF
From the initial screen, press the MATRIX button, and
then press the MENU button to display the [MATRIX
CONTROL] menu.
Press the 3 button to display the [CAMERA ID SET]
menu. (In MATRIX, wait for data loading completion.)
Move the joystick to select the DISPLAY POSITION from the
MATRIX screen, and then press the “FOCUS +“button.
Move the joystick up/down to select a monitor, move
it left/right to select ON/OFF.
Press the “FOCUS +“button to save.
SYSTEM CONTROLLER
42 User’s Manual
[MATRIX screen]
From the initial screen, press the MATRIX button, and
then press the MENU button to display the [MATRIX
CONTROL] menu.
Press the 3 button to display the [CAMERA ID SET]
menu. (In MATRIX, wait for data loading completion.)
Move the joystick to select the DISPLAY POSITION
from the MATRIX screen, and then press the “FOCUS
+“button.
Move the joystick up/down/left/right to move the ID location.
Press the “FOCUS +“button to save.
ENGLISH
4-3. Setting the DISPLAY POSITION
4. ID SET
[MATRIX screen]
5. TIME/DATE SET
This is a function to modify the TIME and DATE on
the corresponding camera.
[MATRIX screen]
5-1. Setting TIME/DATE
From the initial screen, press the MATRIX button, and
then press the MENU button to display the [MATRIX
CONTROL] menu.
Press the 4 button to display the [TIME SET] menu. (In
MATRIX, wait for data loading completion.)
Move the joystick to select the TIME/DATE SET from the
MATRIX screen, and then press the “FOCUS +“button.
[MATRIX screen]
Move the joystick up/down to change the TIME or
DATE, move it left/right to move the location.
Move the joystick to select the “SAVE?” and wait for it to blink, and then press the
“FOCUS +“ button to save.
SYSTEM CONTROLLER
43 User’s Manual
MATRIX Mode
What to do when the product malfunctions
From the initial screen, press the MATRIX button, and
then press the MENU button to display the [MATRIX
CONTROL] menu.
Press the 4 button to display the [TIME SET] menu. (In
MATRIX, wait for data loading completion.)
Move the joystick to select the TIME/DATE ON/OFF
from the MATRIX screen, and then press the “FOCUS
[MATRIX screen]
+“ button.
Move the joystick up/down to select a monitor, move it left/right to select ON/OFF.
Press the “FOCUS +“ button to save.
• Power button is pressed, but nothing is happening
Check if the Adapter is connected to its proper location on the Junction Box.
Check the cable that connects the Controller to the Junction Box.
• System is not operating
If the Initial Setup menu does not display correctly, update the firmware.
• Joystick and/or keys are not working
There might be a problem with the Controller, please contact our agency nearby.
Appearance
5-3. Setting DISPLAY POSITION
From the initial screen, press the MATRIX button, and
then press the MENU button to display the [MATRIX
CONTROL] menu.
Press the 4 button to display the [TIME SET] menu. (In
MATRIX, wait for data loading completion.)
Move the joystick to select the DISPLAY POSITION
from the MATRIX screen, and then press the “FOCUS
+“ button.
Move the joystick up/down/left/right to move the display position.
Press the “FOCUS +“ button to save.
[MATRIX screen]
Caution
• ERROR may occur if operated before data is fully loaded.
SYSTEM CONTROLLER
44 User’s Manual
SYSTEM CONTROLLER
45 User’s Manual
ENGLISH
5-2. Setting ON/OFF
Controller Specifications
SCC-3100A
ENGLISH
MODEL
Connector
LCD Display
PTZ Operation
Sub Keyboard
3 Port
20 x 4 Character LCD
Joystick (3 axis Twist Zoom)
Max. 16 things connection
Speed Dome
Samsung Techwin(SPD), PELCO-D, PELCO-P, PANASONIC
(PANA), SAMSUNG ELECTRONICS (SEC), ELMO, BOSCH
Control
Control Quantity
Auto Surveillance
Remote Control
RS-485/422 Spec.
Power (Consumption)
Operating Temperature/
Humidity
Size
Weight
DVR
SVR-1650/1640/950, SVR-1630/430/440, SVR-5416/5116
Receiver
SRX-100B
MATRIX
SMX-25632
PTZ & DVR Max. 255
- Tour, Group, Swing, Preset etc.
- Selection of PTZ, DVR: Each ID input
RS-485/ RS-422 (Remote control 1.2km above possibility)
Communication set Asynchronism SERIAL, 1 Start Bit, No Parity, 1 Stop Bit
Transmission method Half Duplex / Full Duplex
- 4,800~38,400 bps (9,600 bps Promotion)
Baud Rate (bps)
- Sub-controller communication 57,600 bps fixation
12V DC, 700mA
0~40˚C / 10~75%
400(W) x 180(H) x 88(D)mm
About 1.5kg (Adapter Exclusion)
SYSTEM CONTROLLER
46 User’s Manual
SYSTEM CONTROLLER
47 User’s Manual
Download PDF