TOA CS-154BS Manual

TOA CS-154BS Manual
INSTRUCTION MANUAL
WIDE RANGE SPEAKER
CS-154BS
TABLE OF CONTENTS
1. SAFETY PRECAUTIONS ........................... 2
5. INSTALLATION PRECAUTION ................. 7
2. GENERAL DESCRIPTION
6. DIMENSIONAL DIAGRAM ......................... 8
AND FEATURES ........................................ 3
7. WIRING DIAGRAM ..................................... 8
3. IMPEDANCE CHANGE .............................. 4
8. FREQUENCY RESPONSE ......................... 8
4. WIRING
4.1. When No Bridge Connection
is Required ......................................... 4
4.2. When Bridge Connection
is Required ......................................... 5
9. SPECIFICATIONS ...................................... 9
Thank you for purchasing TOA's Wide Range Speaker.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
Traceability Information for Europe (EMC directive 2004/108/EC)
Manufacturer:
TOA Corporation
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo,
Japan
Authorized representative:
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg,
Germany
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
WARNING
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
When Installing the Unit
• Refer all installation work to the dealer from whom
the speaker was purchased. Installation work
requires extensive technical knowledge and
experience. The speaker may fall off if incorrectly
installed, resulting in possible personal injury.
• Install the speaker only in a location that can
structurally support the full weight of the unit and
mounting bracket. Doing otherwise may result in
the speaker falling down and causing personal
injury and/or property damage.
• When installing the speaker in the snowy area,
take appropriate measures to prevent snow from
lying on the speaker. If the snow lies on it, the
speaker may fall, causing personal injuries.
• Do not use other methods than specified to install
the speaker. Extreme force is applied to the
speaker and the speaker could fall off, possibly
resulting in personal injuries.
• Use screws that are appropriate for the ceiling's or
wall's material and structure. Failure to do so may
cause the speaker to fall, resulting in material
damage and possible personal injury.
• Ensure that all screws are securely tightened. If
they are loose after installation, the speaker could
fall down, possibly resulting in personal injury.
• Do not mount the speaker in locations exposed to
constant vibration. The speaker or its mounts can
be damaged by excessive vibration, potentially
causing the speaker to fall, which could result in
personal injury.
2
• Do not use anti-rust lubricant. If it contacts resin or
rubber parts, they could deteriorate and cause the
speaker to fall, possibly resulting in personal injury.
• Avoid installing the speaker near seaside or in
locations exposed to corrosive gas. The speaker or
its parts may be subject to corrosion, which might
cause it to fall or result in personal injury.
• Do not install the speaker in indoor swimming pools
or such locations where liquid chemicals are used.
The parts deteriorate if corroded, causing the
speaker to fall, which could result in personal
injury.
When the Unit is in Use
• If any of the following irregularities occurs,
immediately switch off the amplifier's power, and
inform the shop from where the speaker was
purchased. Further using the speaker may result in
fire or electric shock.
· If you detect smoke or a strange smell coming
from the speaker
· If water or any metallic object gets into the
speaker
· If the speaker falls, or the speaker case breaks
• To prevent a fire or electric shock, never open nor
remove the speaker case. Refer all servicing to
your nearest TOA dealer.
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
When Installing the Unit
• Avoid touching the speaker's sharp metal edge to
prevent injury.
• To avoid electric shocks, be sure to switch off the
amplifier's power when connecting speakers.
When the Unit is in Use
• Do not operate the speaker for an extended period
of time with the sound distorting. Doing so may
cause the speaker to heat, resulting in a fire.
• Do not stand or sit on, nor hang down from the
speaker as this may cause it to fall down or drop,
resulting in personal injury and/or property
damage.
• Have the speaker checked periodically by the shop
from where it was purchased. Failure to do so may
result in corrosion or damage to the speaker or the
mounts that could cause it to fall, possibly causing
personal injury.
2. GENERAL DESCRIPTION AND FEATURES
TOA's CS-154BS Wide range speaker features an ABS resin enclosure and stainless steel bracket for allweather durability. It is comprised of a high-efficiency weather-resistant horn and a high quality sound cone
speaker, providing clear and highly directional sound reproduction. The CS-154BS is equipped with a constant
directivity horn (90° horizontal) to control sound directivity, realizing uniform and clear sound dispersion over a
wide area.
The CS-154BS is certified to the European Standard EN 54-24: 2008 and the International Standard ISO
7240-24: 2010, and is compliant with the British Standard BS 5839-8: 2008.
• Wide-range speaker suitable for voice evacuation, background music, and paging announcements
applications.
• Comprised of a horn and cone speaker in combination, reproducing high efficiency and high quality sound.
• Constant directivity horn improves directivity characteristics and ensures uniform, clear sound dispersion.
• Weatherproof polyurethane resin paint protects the speaker from damage by ultraviolet light.
• Stainless steel bracket is protected from corrosion.
• Certified to EN 54-24, and ISO 7240-24, and compliant with BS 5839-8.
• Equipped with a large steatite terminal block of screw type and thermal fuse.
• Provided with a cable gland on the terminal cover.
• One cable gland can be added, enabling bridge wiring.
• Impedance change available by a rotary switch located inside the terminal cover.
3
3. IMPEDANCE CHANGE
Input impedance is factory-preset to 670 Ω.
To change the impedance, change the rear panel-mounted rotary switch position using a standard
screwdriver.
Notes
• This speaker is designed to be used for high impedance (70 V/100 V). Never connect the speaker to low
impedance line.
• No sound is output from the speaker when the switch is set to the OFF position.
Caution
Never set the switch to "–" position for 100 V line operation, as doing so may result in damage to the speaker.
Line Voltage
Imp.
100V LINE
15W 670Ω
10W 1kΩ
OFF
100 V
70 V
—
15 W
330 Ω
5W 2kΩ
OFF
OFF
15 W
7.5 W
670 Ω
15W 330Ω
2.5W 2kΩ
10 W
5W
5W
2.5 W
1 kΩ
2 kΩ
OFF
7.5W 670Ω
5W 1kΩ
70V LINE
Bold figures represent factory-preset values.
4. WIRING
The terminal cover is not mounted to the speaker unit when shipped from the factory.
Note
To complete speaker installation, be sure to attach the terminal cover after finishing cable connections.
If the unit is left without the terminal cover attached, water or moisture may get inside the speaker, causing the
unit malfunction.
Unit: mm (in)
4.1. When No Bridge Connection is Required
Step 1. Strip the speaker cable jacket as shown at right.
8
(0.31)
65 (2.56)
Step 2. Run the speaker cable through the cable gland.
Cable gland
Terminal cover
Speaker cable
Step 3. Connect the speaker cable according to the polarity indication at the screw terminal.
Screw terminal
COM
Speaker cable
COM
HOT
EARTH
HOT
EARTH
4
Step 4. Attach the terminal cover.
Secure the terminal cover using the 4 supplied screws.
In this case, take care not to pinch the wiring, and check that the waterproof gasket is secured into
place.
Note
If wiring or the waterproof gasket is pinched between the terminal cover and the unit case, this causes
water or moisture to get inside the terminal cover.
Terminal cover
Screw
Screw
5
Inside view of the Terminal cover
Screw
Cable gland
4
Screw
Screw
4
Waterproof gasket
Terminal cover
Screw
Cable gland
Step 5. Securely tighten the cable gland.
Note
If loosely tightened, water or moisture may get inside the terminal cover.
4.2. When Bridge Connection is Required
Step 1. Punch a knockout hole.
Punch out the knockout on the terminal cover by tapping the center of
the knockout with a screwdriver or other tool.
Note
Clean burrs off the knockout hole after removing the knockout.
If the cable gland is attached with the burrs left in the hole, water
may get inside the terminal cover.
Knockout
Terminal cover
5
Step 2. Mount the cable gland to be added.
Notes
• Prepare the cable gland of PG 13.5 size separately.
• Ensure that the cable gland is securely tightened. If loosely tightened, water may get inside the
terminal cover.
Waterproof gasket
Nut
Cable gland
Terminal cover
Step 3. Strip the speaker cable jacket. (Refer to page 4, Step 1.)
Step 4. Run one each of speaker cables through the cable gland.
Terminal cover
Cable glands
Speaker cables
Step 5. Connect the speaker cables with the same polarity to each terminal according to the polarity indication
at the screw terminal.
Screw terminal
COM
Speaker cables
COM
HOT
EARTH
EARTH
6
HOT
Step 6. Attach the terminal cover.
Secure the terminal cover using the 4 supplied screws.
In this case, take care not to pinch the wiring, and check that the waterproof gasket is secured into
place.
Note
If wiring or the waterproof gasket is pinched between the terminal cover and the unit case, this causes
water or moisture to get inside the terminal cover.
Terminal cover
Screw
5
Inside view of theTerminal cover
Cable glands
Screw
4
Screw
Screw
4
Screw
Waterproof gasket
Terminal cover
Screw
Cable glands
Step 7. Securely tighten the cable glands.
Note
If loosely tightened, water or moisture may get inside the terminal cover.
5. INSTALLATION PRECAUTION
40°
25°
Less than 15 mm (0.59")
• The mounting bracket cannot be adjusted within the angle shown in the figure below, which differs
depending on the number of cable glands mounted on the terminal cover as follows.
· When 1 cable gland is mounted: 25° range not adjustable
· When 2 cable glands are mounted (one is additional): 40° range not adjustable
• Be sure that the bolt projection length from wall surface is less than 15 mm (0.59"). If the length is increased
beyond 15 mm (0.59"), the bolt touches the speaker's terminal cover, causing the speaker mounting angle to
be limited further.
Within 90°
• Do not install the speaker face-up from a horizontal plane nor in such a way that the paper cone is exposed
to direct sunlight.
If water accumulates on the paper cone, or ultraviolet rays are radiated on it, this may cause the paper cone
to deteriorate, leading to speaker malfunction.
7
6. DIMENSIONAL DIAGRAM
310 (12.2)
272 (10.71)
171.5 (6.75)
144 (5.67)
172 (6.77)
230 (9.06)
366 (14.41)
236 (9.29)
37 (1.46)
51
51
(2.01)(2.01)
Unit: mm (in)
3-ø11 (0.43)
7. WIRING DIAGRAM
Thermal fuse (84°C or 183.2°F)
OFF
2 kΩ
1 kΩ
EARTH
8Ω
670 Ω
HOT
OFF
COM
Screw
terminal
330 Ω
COM
Rotary switch
0
Matching
transformer
(Shown above is the factory default wiring.)
8. FREQUENCY RESPONSE
[dB]
100
90
80
70
60
50
20
50
100
500
1k
Frequency Response (1 W, 4 m)
8
5k
10 k
20 k
[Hz]
9. SPECIFICATIONS
Standards
Environment Type
Rated Noise Power
Rated Impedance
Sensitivity
Max.SPL
Frequency Response
Coverage Angle (–6 dB)
Speaker Component
Operating Temperature
Dust/Water Protection
Cable Gland
Cable Connection
Applicable Cable Size
Finish
Dimensions
Weight
Accessory
Certified to the European Standard EN 54-24:2008
EN 54-24: 2008
Loudspeaker for voice alarm systems
11
for fire detection and fire alarm systems
0359-CPD-0108
0359
Certification No. 0359-CPD-0108
Certified to the International Standard ISO 7240-24: 2010 Sound-system
loudspeaker for fire detection and fire alarm systems
In Compliance with the British Standard BS 5839-8: 2008 14.8
Type B (Outdoor applications)
15 W (100 V line and 70 V line)
100 V line: 670 Ω (15 W), 1 kΩ (10 W), 2 kΩ (5 W)
70 V line: 330 Ω (15 W), 670 Ω (7.5 W), 1 kΩ (5 W), 2 kΩ (2.5 W)
97 dB (1 W, 1 m at 330 Hz to 3.3 kHz pink noise)
94 dB (1 W, 1 m at 100 Hz to 10 kHz pink noise)
82 dB (1 W, 4 m at 100 Hz to 10 kHz pink noise)
104 dB (15 W, 1 m at 100 Hz to 10 kHz pink noise)
92 dB (15 W, 4 m at 100 Hz to 10 kHz pink noise)
150 Hz – 15 kHz
Horizontal: 140° (500 Hz), 90° (1 kHz), 90° (2 kHz), 100° (4 kHz)
Vertical: 200° (500 Hz), 155° (1 kHz), 90° (2 kHz), 60° (4 kHz)
12 cm (5") cone-type (treated for splash proof)
–20 ºC to +55 ºC (–4 ºF to +131 ºF)
IP65
Size: PG 13.5
One cable gland is factory-installed.
For bridge connection, one cable gland can be added.*
Screw terminal (Steatite), can be bridge-connected
Outer diameter:
ø8.0 – ø12.5 mm
Conductor:
Solid wire or 7-core wire
No bridge connection: 0.8 – 10 mm2 (AWG18 – 7) for solid wire,
0.8 – 8 mm2 (AWG18 – 8) for 7-core wire
Bridge connection:
0.8 – 2.5 mm2 (AWG18 – 13) for solid wire,
0.8 – 1.5 mm2 (AWG18 – 15) for 7-core wire
Horn, Cover, and Terminal cover: ABS resin, off-white, paint
Bracket:
Stainless steel
Net:
Aluminum, gray, paint
Screw:
Stainless steel
366 (w) x 230 (h) x 310 (d) mm (14.41" x 9.06" x 12.2")
3.0 kg (6.61 lb)
Terminal cover ..... 1
Notes
• The design and specifications are subject to change without notice for improvement.
• The specifications data was measured in an anechoic chamber, according to EN 54-24.
• Reference axis: Axis is on the center of horn-mouth and perpendicular to the horn-mouth.
• Reference plane: Plane is on the horn-mouth and perpendicular to the reference axis.
• Horizontal plane: Plane is containing the reference axis and perpendicular to the reference plane.
* Suppliable cable gland's part code and name: 525-52-011-70 Cable gland AVC PGB13.5-12 (GRY)
9
URL: http://www.toa.jp/
533-06-246-30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement