Samsung | WIP-500M | Specifications | Samsung WIP-500M Specifications

TM
OfficeServ 500
General Description
Every effort has been made to eliminate errors and ambiguities in the information contained in this booklet. Any questions concerning information presented here should be directed to SAMSUNG TELECOMMUNICATIONS AMERICA. SAMSUNG TELECOMMUNICATIONS AMERICA disclaims all liabilities for damages arising from erroneous interpretation or
use of information presented in this manual.
Publication Information
SAMSUNG TELECOMMUNICATIONS AMERICA reserves the right without prior notice to revise
information in this publication for any reason.
SAMSUNG TELECOMMUNICATIONS AMERICA also reserves the right without prior notice to
make changes in design or components of equipment as engineering and manufacturing may
warrant.
Copyright 2006
Samsung Telecommunications America
All rights reserved. No part of this manual may be reproduced in any form or by any means—
graphic, electronic or mechanical, including recording, taping, photocopying or information
retrieval systems—without express written permission of the publisher of this material.
PRINTED IN USA
05/06
TABLE OF CONTENTS
PART
1
2
DESCRIPTION
PAGE
SYSTEM OVERVIEW
1.1
GENERAL DESCRIPTION ..........................................................................................................................1.2
1.2
SIZE AND CONFIGURATION ..................................................................................................................1.2
1.3
MAXIMUM DEVICE QUANTITIES ..........................................................................................................1.4
1.4
INTERIOR VIEW OF THE CABINET ........................................................................................................1.5
1.5
BAYFACE LAYOUT - SINGLE CABINET SYSTEM ................................................................................1.5
1.6
BAYFACE LAYOUT - MULTIPLE CABINET SYSTEM............................................................................1.6
1.7
TECHNOLOGY ............................................................................................................................................1.7
1.8
PROGRAMMING ........................................................................................................................................1.7
1.9
SOFTWARE VERSIONS ..............................................................................................................................1.7
HARDWARE DESCRIPTIONS
2.1
SYSTEM CABINETS ....................................................................................................................................2.1
2.2
COMMON CONTROL CARDS ................................................................................................................2.1
2.2.1 PROCESSOR CARDS ....................................................................................................................2.1
2.2.2 PROCESSOR CARD DAUGHTER BOARDS..............................................................................2.4
2.2.3 SMARTMEDIA CARDS ..................................................................................................................2.5
2.2.4 INPUT-OUTPUT MODEM (IOM) BOARD ................................................................................2.5
2.2.5 MODEM DAUGHTER BOARD ....................................................................................................2.5
2.3
INTERFACE CARDS ....................................................................................................................................2.5
2.3.1 TRUNK CARDS ................................................................................................................................2.5
2.3.2 STATION CARDS ............................................................................................................................2.7
2.3.3 OTHER CARDS ................................................................................................................................2.8
2.4
STATION EQUIPMENT ..............................................................................................................................2.9
2.4.1 DS 5000 SERIES EQUIPMENT ....................................................................................................2.9
2.4.2 iDCS SERIES EQUIPMENT ........................................................................................................2.11
2.4.3 DCS SERIES KEYSETS ................................................................................................................2.13
2.4.4 OFFICESERV™ ITP-5100 SERIES EQUIPMENT....................................................................2.14
2.4.5 OFFICESERV™ SOFTPHONE....................................................................................................2.14
2.4.6 OFFICESERV™ WIRELESS..........................................................................................................2.15
3
SPECIFICATIONS
3.1a ELECTRICAL SPECIFICATIONS (PSU 60)..............................................................................................3.1
3.1b ELECTRICAL SPECIFICATIONS (PSU-60B) ..........................................................................................3.1
3.2
DIMENSIONS AND WEIGHTS ................................................................................................................3.2
3.3
ENVIRONMENTAL LIMITS ........................................................................................................................3.2
3.4
CABLE REQUIREMENTS............................................................................................................................3.2
3.5
SYSTEM TONES ..........................................................................................................................................3.3
3.6
KEYSET LED INDICATIONS ......................................................................................................................3.4
3.7a RESERVE POWER DURATION ESTIMATES (UPS) ............................................................................3.5
3.7b RESERVE POWER DURATION ESTIMATES (BATTERY) ....................................................................3.5
SAMSUNG OFFICESERV 500 TABLE SIZE COMPARISON ............................................................................3.6
4
BUSINESS FEATURE PACKAGE
4.1
SYSTEM FEATURES DESCRIPTIONS......................................................................................................4.3
4.2
STATION FEATURES DESCRIPTIONS ..................................................................................................4.30
4.3
DISPLAY FEATURES DESCRIPTIONS ..................................................................................................4.37
4.4
SAMPLE SMDR PRINTOUT WITHOUT CALLER ID ........................................................................4.44
4.5
SAMPLE SMDR PRINTOUT WITH CALLER ID/ANI NUMBER ......................................................4.45
4.6
SAMPLE OF UCD EMBEDDED REPORT ............................................................................................4.46
4.7
UCD CALL STATISTICS............................................................................................................................4.47
4.8
UCD AGENT STATISTICS ........................................................................................................................4.49
4.9
SAMPLE TRAFFIC REPORT ....................................................................................................................4.50
4.10 TRAFFIC REPORT OVERVIEW ..............................................................................................................4.51
5
6
GENERAL USER INFORMATION
5.1
RADIO FREQUENCY INTERFERENCE....................................................................................................5.1
5.2
FCC REQUIREMENTS ................................................................................................................................5.1
5.3
TELEPHONE COMPANY INTERFACES ..................................................................................................5.2
5.4
UNDERWRITERS LABORATORIES..........................................................................................................5.3
5.5
MUSIC ON HOLD WARNING ..................................................................................................................5.3
5.6
EQUAL ACCESS REQUIREMENTS ..........................................................................................................5.4
5.7
DISA WARNING ..........................................................................................................................................5.4
HOTEL/MOTEL FETURE PACKAGE ............................................................................6.1
6.1
GENERAL OVERVIEW ................................................................................................................................6.1
6.2
HOTEL/MOTEL FEATURES ......................................................................................................................6.2
6.3
SAMPLE REPORTS AND PRINTOUTS....................................................................................................6.9
6.3.1
GUEST ROOM BILL PRINTOUT ............................................................................................6.10
6.3.2
ROOM STATUS PRINTOUTS ..................................................................................................6.12
6.3.3
TRANSACTION RECORD OUTPUT SAMPLE ....................................................................6.24
6.3.4
INDIVIDUAL GUEST PHONE BILL ........................................................................................6.26
6.3.5
ALL GUEST PHONE BILL (SMDR) ........................................................................................6.28
6.3.6
INDIVIDUAL WAKEUP ACTIVITY REPORT ........................................................................6.29
LIMITED WARRANTY
OfficeServ 500 General System Diagram
iDCS 28 Button Keyset
iDCS 8 Button Keyset
iDCS 18 Button Keyset
iDCS 14 Button
AOM
iDCS 64 Button
AOM
DS 5021D Keyset
DS 5014D Keyset
DS 5007S Keyset
DS 5064 AOM
ITP-5107S Keyset
ITP-5112L Keyset
ITP-5121D Keyset
Softphone
110/220V AC
Door Phone
System Programming
Remote Programming
Computer Telephony
Integration
48 VDC Battery
Backup
Telephone Lines
-Loop Start with
Caller ID
-E&M Tie Line
-T1
-ISDN PRI
Printer or Call
Accounting System
Loud Bells
Integrated
Voice Mail &
Auto Attendant
External Music
Sources
1.1
External Paging
4 Zones
PART 1. SYSTEM OVERVIEW
1.1 GENERAL DESCRIPTION
The SAMSUNG OfficeServ 500 (Digital Communications System) is a VoIP enabled digital telephone system
designed for small to medium-sized businesses. It can operate with the functionality of a square key system, PABX
or a combination of both (hybrid). The DCS employs DSP (Digital Signal Processors) digital technology. With integrated Media Gateway Cards (MGI), local IP keysets, remote IP keysets and IP networking are easily and economically added as needed.
The OfficeServ 500 offers a variety of interface cards that allow connection to the public telephone network or to
private networks.These are generally referred to as trunk cards.Two types of telephones can be connected to the
system. Proprietary digital phones called “keysets” connect to Digital Line Interface cards (DLI) or connect to an
Ethernet LAN and communicate with the system through the Media Gateway Interface cards (MGI). Standard telephones generally called “single line sets” connect to single line interface cards (SLI). In addition, DLI station ports
are used to connect peripheral devices such as door phones and add-on modules. Miscellaneous circuits are provided to allow such optional features as external paging, music on hold, background music, and common audible
devices. All interface cards are encased in an anti-static plastic enclosure and most can be inserted or removed
with power on to eliminate unnecessary service interruptions while performing maintenance.
All keysets utilize a single PCB with surface-mounted components assuring the highest product quality and long
life. Samsung’s customary large, easy-to-read displays and LEDs in the button design make them much easier to
use. In many instances, sophisticated features are made simple through the use of friendly display prompts or
push-on/push-off feature keys.
Expanding the OfficeServ 500 system is both economical and easy. Begin with a single cabinet configured as a
basic Key Service Unit and then add up to two more cabinets as your business grows. Its low and medium density card design allows greater flexibility when configuring a system for the right combination of lines and stations.
A removable software cartridge (SmartMedia card) makes it convenient to upgrade to future feature packages.
1.2 SIZE AND CONFIGURATION
The OfficeServ 500 is a fully modular system comprised of a single cabinet configured as a Key Service Unit, up to
two additional cabinets, interface cards and electronic keysets. A fully expanded system using the T1/PRI cards
can have a maximum of 352 lines or 360 stations. Without the T1/PRI cards, the maximum number of lines is 208
and the maximum number of stations is 360.The maximum number of ports supported by the system is 488. Each
cabinet of the system supports two power supply units, the first of which must be a PSU-B and can support up to
56 stations. When assisted by a second PSU-B the cabinet can support up to 120 station devices. Both power supply units are connected to the DC bus for external battery backup. Each cabinet also has four (4) Digital Signal
Processor (DSP) channels for use as DTMF receivers or tone detectors.
SINGLE CABINET SYSTEM
A single cabinet system has eight universal interface card slots, a
dual purpose interface card / signal processor card, a main processor
card slot, and two power supply slots, the first of which must be
occupied by a PSU-B (see Figure 1–1). If “M” version software is used
then nine slots can be used for interface cards. If “L” version software
is used then eight interface cards can be installed and an SCP2 card
must be installed in the dual purpose slot. Station or trunk (Line)
cards can be installed in any interface card slot. TEPRI/TEPRIa cards
must be installed in slots 1, 2 or 3.This allows a maximum of 120 stations or 120 lines with T1’s being used or 72 lines without T1’s.
FIGURE 1-1
1.2
TWO CABINET SYSTEM
When it is required that the basic system be expanded to provide a
capacity greater than that described above, the Release 2 Signal
Control Processor (SCP2) card must be installed in slot nine of the
first cabinet. This card provides an intermediate level of processing
to control the first cabinet therefore freeing resources on the
Release 2 Main Control Processor (MCP2) to control the entire system. Adding the SCP2 card therefore reduces the number of universal card slots in the first cabinet to eight. In addition, the MCP2 card
must be equipped with an ESM daughter board. All other types of
daughter boards must be installed on the SCP2 card or LCP2 card.
Adding one expansion cabinet makes the system a two cabinet system with 17 universal card slots (see Figure 1–2). This allows a maximum of 240 stations or 232 lines when using T1/PRI cards. Without
the T1/PRI cards, the maximum number of lines is 136 while the
maximum number of stations remains at 240. This second cabinet is
controlled by a Release 2 Local Control Processor (LCP2) in a similar
manner to the SCP2 in the first cabinet and connects to the MCP2
via a 25 pair cable. The LCP2 processor card resides in the dedicated
slot 10 of the second cabinet and therefore does not deplete the
number of universal card slots.
FIGURE 1-2
Note: The first power supply slot in each cabinet must be occupied by a PSU-B to supply sufficient power to all 10
slots (9 universal and a processor slot) and support up to 56 stations. The second power supply slot can be occupied by either a PSU60 or PSU-B. Do not use a PSU40 in either PSU slot.
THREE CABINET SYSTEM
In a fully expanded three cabinet system, there are 26 universal card
slots (see Figure 1–3). This allows a maximum of 360 stations or 352
lines when using T1/PRI cards. Without T1/PRI cards, the maximum
number of lines is 208 and the maximum number of stations is 360.
The third cabinet is also controlled by a Local Control Processor
(LCP2) in a similar manner to the LCP2 in the second cabinet and
connects to the second cabinets’ LCP2 via a 25 pair cable. This
processor resides in a dedicated slot 10 and therefore does not
deplete the number of universal card slots. In addition, the MCP2
card must be equipped with an ESM daughter board. All other types
of daughter board must be installed on the SCP2 card or LCP2 card.
Note: The first power supply slot in each cabinet must be occupied
by a PSU-B to supply sufficient power to all 10 slots (9 universal and
a processor slot) and support up to 56 stations. The second power
supply slot can be occupied by either a PSU60 or PSU-B. Do not use
a PSU40 in either PSU slot.
FIGURE 1-3
1.3
1.3 MAXIMUM DEVICE QUANTITIES
DEVICE TYPE
MAXIMUM
NOTES
Physical Ports
488
In a 3 cabinet system
Stations
Digital
Analog
IP
600†
360*
360*
240
† TDM and IP stations combined.
Trunks
Analog
- Loop Start
Digital
- T1/PRI
- BRI
Networking Nodes
Using QSIG over PRI
Using QSIG over IP
352*
208
208
216
216/207
104
99
99
*Maximum number of stations without
any trunks. Limited by the number of
available universal slots and power supply
units.
*Maximum number of trunks without any
stations. Limited by the number of
available universal slots.
Maximum 3 per cabinet, 9 per system.
Use any universal card slot.
*Numbering Plan and Design may yield
less.
Uses available T1/PRI card slots.
Limited by IP Address Table, MMC 820.
Required to connect an IP phone to a
TDM device including paging and
background music and ports used for networking or trunking.
Media Gateway Ports
240
Conferencing Circuits
5 Party Add-On
Unsupervised
Barge-In
Call Record
AME
6/24
6/24
6/24
6/24
6/24
Music On Hold Inputs
6
Paging
Audio Output
Internal Zones
External Zones
3
5
4
1 per MISC card. Maximum 3 MISC cards
per system.
(99 members each zone)
Requires customer provided equipment.
Auto Attendant Ports
40
Maximum 5, 8 port AA cards per system.
Voice Mail / Auto Attendant Ports
SVMi-8E
SVMi-16E
16
8
16
System can have only one of the SVMi
cards installed.
Loud Bell Audio Output
3
1 per MISC card, 3 per system. Requires
customer provided equipment.
1.4
System Wide Conference Circuits.
6 Default, 24 Maximum with SCM board.
2 per MISC card. Maximum 3 MISC cards
per system.
1.4 INTERIOR VIEW OF THE CABINET
w
e
r
t
q
u
q
u
u
u
u
u
u
u
u
y
q
w
e
r
t
y
u
Power Supply Slots (2)
A/C Power Switch
Battery Backup Power Switch
Main Control Processor
LAN Connection
Interface Cards
Serial I/O Ports
BATTERY
LAN
1.5
MCP2/LCP2
Slot 9 / SCP2
Slot 8
Slot 7
Slot 6
Slot 5
SIO3 SIO4
Slot 4
SIO2
Slot 3
Slot 2
Slot 1
SIO1
PSU-B/PSU60
PSU-B
POWER
1.5 BAYFACE LAYOUT - SINGLE CABINET SYSTEM
1.6
LCP2
LCP2
Cabinet 1 / Slot 7
MCP2
Cabinet 3 / Slot 6
Cabinet 2 / Slot 6
Cabinet 3 / Slot 9
Cabinet 3 / Slot 5
Cabinet 2 / Slot 5
Cabinet 2 / Slot 9
Cabinet 3 / Slot 4
Cabinet 2 / Slot 4
SCP2
Cabinet 3 / Slot 3
Cabinet 2 / Slot 3
Cabinet 3 / Slot 8
Cabinet 3 / Slot 2
Cabinet 2 / Slot 2
Cabinet 2 / Slot 8
Cabinet 3 / Slot 1
Cabinet 2 / Slot 1
PSU-B
PSU-B/PSU60
BATTERY
POWER
PSU-B/PSU60
PSU-B
Cabinet 1 / Slot 8
LAN
Cabinet 3 / Slot 7
SIO3 SIO4
Cabinet 2 / Slot 7
Cabinet 1 / Slot 6
Cabinet 1 / Slot 5
SIO2
Cabinet 1 / Slot 4
BATTERY
POWER
SIO1
Cabinet 1 / Slot 3
Cabinet 1 / Slot 2
Cabinet 1 / Slot 1
PSU-B/PSU60
PSU-B
BATTERY
POWER
1.6 BAYFACE LAYOUT - MULTIPLE CABINET SYSTEM
1.7 TECHNOLOGY
MEMORY
The system operates using stored program control.This program is stored on a SmartMedia card inserted into the
Main Control Processor card (MCP2) and contains sixteen Megabytes of NAND-Flash memory. The Smart Media
card also provides space for a backup customer database and a backup operating program. The system boots
from a 1 Megabyte boot ROM and downloads the operating program into thirty two megabytes of DRAM on the
Main Control Processor (MCP2) card. The customer database is stored in four megabytes of non-volatile SRAM.
MICROPROCESSORS
The OfficeServ 500 uses distributed processing. Its primary processor is a 32 bit Motorola MC68360 operating at
a clock speed of 50 MHz on the MCP2 card.This provides all the processing necessary for a single cabinet system.
In a multi cabinet system the secondary level of processing is on the SCP2 card for the first cabinet and on the
LCP2 cards for the expansion cabinets. These secondary processors are MC68302 processors running at 16 MHz
and provide local control of each cabinet. The tertiary level of processing is done in the keysets. The digital keysets use a Hitachi H8 processor for data communication within the system.
1.8 PROGRAMMING
The OfficeServ 500 is a self-configuring system.This means that immediately after applying power, the OfficeServ
500 reads the types and locations of all installed interface cards and keysets and assigns default data to them.This
data provides for system operation within a few minutes after applying power. All trunks and stations are
assigned three or four digit numbers according to the settings of the switches on the MCP2 card and the default
numbering plan. This numbering plan is flexible and may be changed to suit customer requirements. The
installing technician customizes this default data to meet the end user’s requirements.
The system can be programmed from any LCD display keyset without interrupting system operation. There are
three levels of programming: technician, customer and station.The technician level has access to all programs and
can allow the customer access to system programs as needed. Technician and customer access levels are controlled by a different security passcodes and access procedure.
The OfficeServ 500 also allows the use of a proprietary computer program called SAPM-PCMMC. This permits a
technician to program the system using a personal computer. SAPM-PCMMC can be used on-site to modify the
customer database or to download (save) the entire customer database to a file. This file can then be saved as a
backup and be uploaded when required to restore the database.Through the use of modems, SAPM-PCMMC can
access the OfficeServ 500 system remotely (off-site) to make database changes or perform uploads or downloads
of the customer database as if the technician were on-site.
1.9 SOFTWARE VERSIONS
The OfficeServ 500 system can be equipped with one of two versions of software to meet different customer
needs.
M VERSION-RELEASE 2
This version of software provides the software features for a single cabinet system and requires only the MCP2
card to run.
L VERSION-RELEASE 2
This version of software is required to run a multiple cabinet system although it can be used in a single cabinet
environment. For L version software to operate correctly each cabinet must have its own “Local” processor card
installed in it, that is the SCP2 for the first cabinet and the LCP2 for the second and third cabinets. In addition, in
a multiple cabinet environment, the MCP2 card MUST have an ESM daughterboard installed in position D1.
1.7
PART 2. HARDWARE DESCRIPTIONS
2.1 SYSTEM CABINETS
The cabinets that make up the OfficeServ 500 system are of metal construction and may be utilized as either as
an expansion cabinet or as a main cabinet / key service unit (KSU). The cabinets may be used individually or may
be stacked up to three (3) high to achieve maximum capacity. A single cabinet may be wall mounted for smaller
applications or alternatively the system may be mounted in a standard nineteen inch (19”) equipment rack after
removal of the side panels and their supporting brackets. Each cabinet is comprised of the following:
•
•
•
•
•
•
•
•
Eight interface card slots
One dual purpose interface card / signal processor slot (see Part 1.2 Size and Configuration)
One processor card slot
Two power supply slots
One IOM board slot for use when the cabinet is the main cabinet/KSU (see Part 2.2.4 IOM Board)
AC power connector
DC power (Battery Backup) connector
Four DSPs for the DTMF and tone detection
NOTE: The first power supply slot must be occupied by a PSU-B power supply to supply sufficient power to all 10
slots (8 interface, one dual purpose and one processor slot). The second power supply slot can be occupied by
either a PSU 60 or a PSU-B. Do not install a PSU 40 in any PSU slot.
2.2 COMMON CONTROL CARDS
2.2.1 PROCESSOR CARDS
The OfficeServ 500 requires a processor card or cards in order to operate. In a single cabinet OfficeServ 500 system, running M version software only one processor card, the Main Control Processor (MCP2), is required. When
the system is expanded to two or three cabinets or L software is required, a second Switch Control Processor
(SCP2) is required for the main cabinet to assist the MCP2, and each expansion cabinet requires its own Local
Control Processor (LCP2). These processor cards are described below.
MAIN CONTROL PROCESSOR (MCP2)
The Main Control Processor (MCP2) is installed in a dedicated processor slot, slot 10, of the first cabinet and has
positions for three daughter boards. The first daughter board position (MCP2_D1) can support one of four types
of daughter board, a Multi-Frequency Module (MFM), a Switch/Conference Module (SCM), an R2/CID Module
(RCM2), in a single cabinet system running M version software and is required to support the Expanded Switching
Module (ESM) in a multiple cabinet system running L software. The second daughter board position (MCP2_D2)
can support the MFM, the SCM, or the RCM2 board. The third daughter board (MCP2_D3) can support a
Miscellaneous (MISC) daughter board, the MFM, the SCM, or the RCM2 board.
2.1
MAIN CONTROL PROCESSOR (MCP2) DAUGHTER BOARD CAPABILITIES
Position
Types of Daughter Boards allowed per position
MCP2 - D1
MFM, SCM, RCM2 and ESM*
MCP2 - D2
MFM, SCM and RCM2
MCP2 - D3
MFM, SCM, RCM and MISC
* The ESM must be installed in this position in a Multiple Cabinet .
Note: Only one of any type of daughter board may be installed on any processor card. In an L version system ONLY
the ESM board can be installed on the MCP2 card. Do not install any other types of daughterboard on the MCP2
in an L version system. Other daughterboards may be installed on the SCP2 card.
SWITCH CONTROL PROCESSOR (SCP2)
The Switch Control Processor (SCP2) is installed in slot 9 of the KSU and reduces the available universal card slots
to eight. The SCP2 card is required when the system is to be expanded beyond a single cabinet or L version software is required. The SCP2 card has positions for three optional daughter boards. The first daughter board position (SCP2-D1) can support one of three types of daughter board, a Multi-Frequency Module (MFM), a
Switch/Conference Module (SCM) or an R2/CID Module (RCM2). The second daughter board position (SCP2-D2)
can support the MFM, the SCM, the RCM2 or the MISC. The third daughter board position (SCP2-D3) can support
one of the three types of daughter board, a Multi-Frequency Module (MFM), a Switch/Conference Module (SCM)
or an R2/CID Module (RCM2).
Note: Only one of any type of daughter board may be installed on any processor card.
SWITCH CONTROL PROCESSOR (SCP2) DAUGHTER
Position
Types of Daughter Boards allowed per position
SCP2 - D1
MFM, SCM, RCM2
SCP2 - D2
MFM, SCM, RCM2, and MISC
SCP2 - D3
MFM, SCM, RCM2
2.2
LOCAL CONTROL PROCESSOR (LCP2)
The Local Control Processor (LCP2) card is installed in a dedicated processor slot, slot 10, of each Expansion KSU
and does not reduce the available universal card slots of that cabinet. The LCP2 card has positions for three
daughter boards. The first daughter board position (LCP2-D1) can support one of two types of daughter board, a
Multi-Frequency Module (MFM), or an R2/CID Module (RCM). The second daughter board position (LCP2-D2) can
support the MFM, the RCM or the MISC. The third daughter board position (LCP2-D3) can support one of two
types of daughter board, a Multi-Frequency Module (MFM), or an R2/CID Module (RCM).
LOCAL CONTROL PROCESSOR (LCP2) DAUGHTER BOARD CAPABILITIES
Position
Types of Daughter Boards allowed per position
LCP2 -D1
MFM, RCM
LCP2 -D2
MFM, RCM and MISC
LCP2 -D3
MFM, RCM
Note: Only one of any type of daughter board may be installed on any processor card.
2.3
2.2.2 PROCESSOR CARD DAUGHTER BOARDS
There are five types of daughter board that fit on the various processor cards. Some daughter boards will only
work on the Main Control Processor (MCP2) and the rest will work on any processor card. The various daughter
boards and their uses are described below.
SWITCH AND CONFERENCE MODULE (SCM)
The Switch and Conference Module installs on the MCP2 or the SCP2 processor cards. In a single cabinet system
the SCM can be installed in MCP2-D1, however in a multiple cabinet system the SCM must be installed on the
SCP2 as the MCP2 must have the ESM daughter board. The system, regardless of size can only support one SCM
daughter board. Adding a SCM daughter board to the system increases the number of conference bridges in the
system from six to twenty four. In addition, the SCM also adds twelve DSPs for DTMF and tone detection.
•
•
Twelve (12) DSPs for DTMF and tone detection
Eighteen (18) conference bridges (for a system total of 24)
MULTI-FREQUENCY MODULE (MFM)
The MFM Module installs in any position of any of the processor cards. The main purpose of the MFM daughter
board is to provide DSPs for DTMF and tone detection.
The receivers are also used for DID trunks, E&M trunks, DISA, DNIS and ANI.
•
Twelve (12) DSPs for DTMF and tone detection.
EXPANDED SWITCH MODULE (ESM)
The Expanded Switch Module is used to expand the time switch matrix from 512 channels in a single cabinet to
the 1024 channels required for a multiple cabinet systems.
The ESM daughter board installs in position MCP2-D1 and consists of the following:
•
1024 channel time switch matrix
Note: This is the ONLY daughterboard that can be installed on the MCP2 in an L version system.
R2/CID-Tx MODULE (RCM2)
The RCM2 Module installs in any position on any of the processor cards. The main purpose of the RCM daughter
board is to provide Caller ID decoders for use with that telephone company provided service over analog trunks.
and DSPs to transmit CID information to analog station ports. A secondary use of the RCM is to provide R2 MFC
senders and receivers to the system although these are not used in the US. The system can support up to three
of these cards for a total of 42 CID receivers.
The RCM2 consists of the following:
•
•
Fourteen (14) CID receivers (for use with Caller ID on analog trunks)
Sixteen (16) CID senders
2.4
MISCELLANEOUS FUNCTION MODULE (MISC)
The Miscellaneous Function Module (MISC) daughter board installs in position MCP2-D3 on the MCP2 card in a
single cabinet system or in position SCP2-D2 on the SCP2 or position LCP2-D2 on the LCP2 card(s) in a multiple
cabinet system. The MISC daughter board is used to provide external music on hold/audio inputs (radios, digital
announcers, etc.), external paging auto output, loud bell, common bell and programmable dry contact closures.
The system can support up to three of these daughter boards, one on the MCP2 or SCP2 and one on each of the
LCP2s.
The MISC consists of the following:
•
•
•
•
•
Two (2) external music/audio inputs
One (1) external paging audio output
One (1) loud bell audio output
One (1) common bell relay contact closure
Two (2) software assignable relay contact closures
2.2.3 SMARTMEDIA CARDS
An OfficeServ 500 system must have a SmartMedia card installed in the main control processor (MCP2) as the
SmartMedia card contains the system operating software. The SmartMedia card can also be used to store a backup customer database to supplement the database stored on the MCP2 card. In addition the SmartMedia card
can store backup copies of the operating software for the SCP2, LCP2, and TEPRI/TEPRIa cards.
2.2.4 INPUT–OUTPUT MODEM (IOM) BOARD
The Input Output Modem board installs in the first cabinet and provides access to the two serial I/O ports on the
Main Control Processor (MCP2) card. Ports 1 and 4 are not used on a Release 2 system.The IOM board also has provision to have an internal 56K/V.90 modem installed on it (see Part 2.2.5).
2.2.5 MODEM DAUGHTER BOARD
The Modem daughter board installs on the Input Output Modem card. The modem provides a 56K/V90 connection to the system for use for remote administration and/or programming.The card has a default extension number of 3999 and eliminates the need for an external modem, serial cable, single line telephone port and serial I/O
port on the system.
2.3 INTERFACE CARDS
These cards provide the interface connections for telephone lines and stations to the KSU and expansion cabinets.These cards fit into the universal card slots to configure the system as required. OfficeServ 500 interface cards
are encased in a static dissipative ABS plastic shell to protect the PCB during handling.
2.3.1 TRUNK CARDS
TRUNK B1
This card contains four loop start C.O. line interface circuits with C.O. disconnect detection. It also contains the circuitry needed for Caller ID. It can be inserted in any universal card slot in all cabinets.
TRUNK C1
This card contains eight loop start C.O. line interface circuits with C.O. disconnect detection. It also contains the
circuitry needed for Caller ID. It can be inserted in any universal card slot in all cabinets.
2.5
TEPRI/TEPRIa DIGITAL TRUNK
When programmed as a T1 this card provides up to 24 trunk circuits in any combination of the following:
•
•
•
•
Loop start lines
DID (Direct Inward Dialing)
Ground start lines
E & M tie lines or two way DID calling
When the card is programmed as a PRI it will provide 23 bearer channels and 1 data channel (23B+D). This card
can be installed in any of the first three slots of any cabinet.
MGI2 (MEDIA GATEWAY INTERFACE)
The MGI2 card supports 16 VOIP channels. These channels are H.323 and SIP compliant and are used in conjunction with either the G.711 (64K) or G.729A (8K) voice compression protocols. The MGI2 card may be installed in
any universal card slot up to a maximum of 5 cards per cabinet. The MGI2 only supports in-band signaling.
The MGI2 cards provide the following services on a per-channel basis:
•
•
•
•
H.323 IP Trunking (VoIP connections to other H.323 gateways)
SIP IP Trunking
ITP Phones
IP Networking (Networking multiple OfficeServ 500 and OfficeServ 100 systems over IP networks)
Note: There is a maximum of 5 MGI cards per cabinet (15 per system). All 5 can be MGI2 or a combination of MGI2
and MGI3 cards, as long as there is no more than 2 MGI3 cards per cabinet.
MGI3 (MEDIA GATEWAY INTERFACE)
The MGI3 card supports up to 16 VoIP channels. There are 8 embedded on the card. An additional 8 channels can
be added by plugging in a daughterboard.
The MGI3 has the capabilities of the MGI2 plus the following:
•
•
•
•
•
G.723.1 (5.3K-6.4K) CODEC
G.729 (8K) CODEC
T.38 Fax CODEC
H.245 Trunking
Out-of-band signaling of DTMF tones
Note: There is a maximum of 5 MGI cards per cabinet (15 per system). All 5 can be MGI2 or a combination of MGI2
and MGI3 cards, as long as there is no more than 2 MGI3 cards per cabinet.
E911 CARD
The E911 card supports up to 4 CAMA (Centralized Automatic Message Accounting) type loop start trunks to provide CESID (Caller Emergency Services ID). These trunks are connected directly to the PSAP (Public Services
Answering Point) to pass on calling station information to enable the emergency services to correctly locate the
source of the call such as a building floor.
2.6
2.3.2 STATION CARDS
DLI
This card is an eight circuit digital station interface card that provides 2B+D service when installed in any universal card slot in all cabinets. Keyset daughter boards will only work when connected to this card.
16DLI
This card is a sixteen circuit digital station interface card that provides 1B+D service when installed in any universal card slot in all cabinets. Keyset daughter boards will not work when connected to this card.
SLI
This card is a four circuit analog station interface for industry standard single line telephones or other analog
peripheral devices (voice mail, etc.). Each circuit is equipped with an analog DTMF receiver and provides the overvoltage protection required for connection to telephone company off premises extension circuits (OPX). It can be
inserted in any universal card slot in all cabinets. Each port on this card is intended for connection to one telephone. Connecting multiple telephones to a port may result in incorrect operation or damage to the card. See the
installation manual part 3 for details.
8SLI
This card is a eight circuit analog station interface for industry standard single line telephones or other analog
peripheral devices.The 8SLI does not contain any over-voltage protection and is not qualified as OPX. It also does
not contain DTMF receivers, but shares system DSP resources. It can be inserted in any universal card slot in all
cabinets. Each port on this card is intended for connection to one telephone. Connecting multiple telephones to
a port may result in incorrect operation or damage to the card. See the installation manual part 3 for details.
16SLI
This card is a sixteen circuit analog station interface for industry standard single line telephones or other analog
peripheral devices. The 16SLI does not contain any over-voltage protection and is not qualified as OPX. It also
does not contain DTMF receivers, but shares system DSP resources. It can be inserted in any universal card slot in
all cabinets. Each port on this card is intended for connection to one telephone. Connecting multiple telephones
to a port may result in incorrect operation or damage to the card. See the installation manual part 3 for details.
8MWSLI
This card is an eight circuit analog station interface for industry standard single line telephones that require operation of an industry standard message waiting lamp with a voltage range of 85 ~ 96 VDC. The lamp can be programmed to be on continuously or flash at a programmable rate of 100ms to 2000ms ON/OFF times.The 8MWSLI
does not contain any over-voltage protection and is not qualified as OPX. It also does not contain DTMF receivers,
but instead shares the system DSP resources. It can be inserted in any universal card slot in all cabinets. Each port
on this card is intended for connection to one telephone. Connecting multiple telephones to a port may result in
incorrect operation or damage to the card. See the installation manual part 3 for details.
16MWSLI
This card is a sixteen circuit analog station interface for industry standard single line telephones that require operation of an industry standard message waiting lamp with a voltage range of 85 ~ 96 VDC. The lamp can be programmed to be on continuously or flash at a programmable rate of 100ms to 2000ms ON/OFF times. The
16MWSLI does not contain any over-voltage protection and is not qualified as OPX. It also does not contain DTMF
receivers, but instead shares the system DSP resources. It can be inserted in any universal card slot in all cabinets.
Each port on this card is intended for connection to one telephone. Connecting multiple telephones to a port
may result in incorrect operation or damage to the card. See the installation manual part 3 for details.
2.7
2.3.3 OTHER CARDS
AUTO ATTENDANT
This optional card can be used for either the Automated Attendant, Uniform Call Distribution or a combination of
both. For more information about the Automated Attendant and UCD, see section 4.1 System Features.
SVMi-8E & SVMi-16E
The SVMi-8E and SVMi-16E Voice Mail system are fully integrated Auto Attendant/Voice Mail/Fax System on a single circuit card.
These optional cards provide either 4 or 8 channels of communication on the SVMi-8E and 8, 12, or 16 channels
of communication on the SVMi-16E. Only one card is permitted per system and it can be installed in any universal card slot.
This fully featured self contained system is connected directly to the system data bus and communicates with the
system processor. This design means that installation time is minimized, operation is streamlined and many features can be implemented that are not normally possible with older conventional stand alone Voice Mail/Auto
Attendant systems.
All the power to run this self contained Voice Mail system comes from the phone system power supply. Each of
the iDCS phone system power supplies are rated according to how many stations they will support. When SVMi8E is installed in the iDCS it counts as 8 stations of the PSU rating regardless of the number of the Voice Processing
Modules (VPM) installed. The SVMi-16E counts as 8 stations of the PSU with no addition VPMs, 10 Stations of the
PSU with 1 VPM, and 12 Stations of the PSU with 2 VPMs installed.
2.8
2.4 STATION EQUIPMENT
2.4.1 DS 5000 SERIES EQUIPMENT
DS 5021D KEYSET (See Figure 2–1)
•
•
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft
keys and a scroll key
21 programmable keys with tri-colored lights
Five fixed function keys
Terminal Status Indicator
Built-in speakerphone
Optional Full Duplex Speakerphone Module
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset
and ringer volumes
Desk- or wall-mounted
FIGURE 2-1
DS 5014D KEYSET (See Figure 2–2)
•
•
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft
keys and a scroll key
14 programmable keys with tri-colored lights
Five fixed function keys
Terminal Status Indicator
Built-in speakerphone
Optional Full Duplex Speakerphone Module
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset
and ringer volumes
Desk- or wall-mounted
FIGURE 2-2
DS 5007S KEYSET (see Figure 2–3)
•
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft
keys and a scroll key
7 programmable keys with tri-colored lights
Five fixed function keys
Terminal Status Indicator
Built-in speakerphone
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset
and ringer volumes
Desk- or wall-mounted
FIGURE 2-3
Note: This keyset type cannot use keyset daughter boards or the 14 button strip.
2.9
DS 5064B AOM (See Figure 2–4)
•
•
•
64 programmable keys with red lights
A maximum of 4 can be assigned to any keyset to provide additional programmable keys
A maximum of 32 per system
FIGURE 2-4
DS-KDB-FULL DUPLEX INTERFACE (DS-KDBF)
This is a daughter board that can be installed only in the DS 5021D or DS 5014D keysets. The standard speakerphone mode of operation for a DS 5000 keyset is “half duplex”. This means that you cannot transmit and receive
speech at the same time. Adding a KDBF to your keyset will convert the speakerphone into full duplex mode
enhancing its operation. The FKDBF does not require a second “B”.
2.10
2.4.2 iDCS SERIES EQUIPMENT
iDCS 28D KEYSET (See Figure 2–5)
•
•
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft keys and
a scroll key
28 programmable keys with tri-colored lights
Four fixed function keys
Terminal Status Indicator
Built-in speakerphone
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset and
ringer volumes
Desk- or wall-mounted
Available in dark gray or light gray
FIGURE 2-5
iDCS 18D KEYSET (See Figure 2–6)
•
•
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft keys and
a scroll key
18 programmable keys with tri-colored lights
Four fixed function keys
Terminal Status Indicator
Built-in speakerphone
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset and
ringer volumes
Desk- or wall-mounted
Available in dark gray or light gray
FIGURE 2-6
iDCS 8D KEYSET (see Figure 2–7)
•
•
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft keys and
a scroll key
8 programmable keys with tri-colored lights
Four fixed function keys
Terminal Status Indicator
Built-in speakerphone
Eight selectable ring tones
UP/DOWN buttons for digital control of speaker, handset and
ringer volumes
Desk- or wall-mounted
Available in dark gray or light gray
Note: This keyset type cannot use keyset daughter boards or the 14 button strip.
2.11
FIGURE 2-7
iDCS 64B AOM (See Figure 2–8)
•
•
•
•
64 programmable keys with red lights
A maximum of 4 can be assigned to any keyset to provide additional programmable keys
A maximum of 32 per system
Available in dark gray or light gray
FIGURE 2-8
iDCS 14B STRIP (See Figure 2–9)
•
•
•
14 programmable keys with red lights
A maximum of one can be added to any 28D or 18D keyset to provide
additional programmable keys
Available in dark gray or light gray
FIGURE 2-9
iDCS KDB-DIGITAL LINE INTERFACE (FKDBD)
This is a daughterboard that can be installed only in the 18 or 28 button keyset.The FKDBD will provide one additional DLI circuit for the connection of any digital station device such as a keyset, add-on module or DPIM. This
FKDBD will only operate when the keyset is connected to an 8 port DLI card so it can use the second B channel.
Each port on this card is intended for connection to one telephone. Connecting multiple telephones to a port
may result in incorrect operation or damage to the card.
Note: Only one KDB can be installed on a keyset.
iDCS KDB-SINGLE LINE INTERFACE (FKDBS)
This is a daughter board that can be installed only in the 18 or 28 button keyset.The FKDBS will provide one additional SLI circuit for the connection of any standard telephone device.This FKDBS will only operate when the keyset is connected to an 8 port DLI card it can use the second B channel. Each port on this card is intended for connection to one telephone. Connecting multiple telephones to a port may result in incorrect operation or damage
to the card.
Note: The circuitry on a FKDBS does not provide a loop open disconnect signal or have the over-voltage protection necessary for OPX operation. Only one KDB can be installed on a keyset.
2.12
iDCS KDB-FULL DUPLEX (FKDBF)
This is a daughter board that can be installed only in the 18 or 28 button keyset. The standard speakerphone
mode of operation for a iDCS keyset is “half duplex”. This means that you cannot transmit and receive speech at
the same time. Adding a FKDBF to your keyset will convert the speakerphone into full duplex mode enhancing
its operation. The FKDBF does not require a second “B” channel like the FKDBD or FKDBS and so can be used on a
16 DLI card. In addition the FKDBF may have up to three (3) external microphones attached to it for conference
room type applications. These microphones require an “EXTMIC” key programmed on the keyset to activate or
deactivate them.
Note: Only one KDB can be installed on a keyset.
DOOR PHONE INTERFACE MODULE (DPIM) & DOOR PHONE
(see Figures 2–10 and 2–11)
•
•
•
•
•
The DPIM adapts any DLI circuit for use with the door phone unit
Commonly used to request entry through locked doors (interior or exterior) or as a room monitoring box
Provides contact control to be used with customer-provided electric door lock
Door phone is wall-mounted
Door phone is weather resistant
FIGURE 2-10
FIGURE 2-11
2.4.3 DCS SERIES KEYSETS
The OfficeServ 500 is compatible with the following models of Samsung’s earlier DCS Keyset family version 1.2
and higher:
•
•
•
•
•
LCD 24B
LCD 12B
7B Keyset
32 Button Add on Module
64 Button Module
2.13
2.4.4 OfficeServ™ ITP-5100 SERIES EQUIPMENT
ITP-5121D IP KEYSET (See Figure 2–12)
•
•
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft keys and a scroll key
Navigation Key
Built-in speakerphone
21 programmable keys with tri-colored LEDs
Five fixed function keys
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Eight selectable ring tones
Desk or wall-mounted
Built-in 2 port data switch
FIGURE 2-12
ITP-5112L IP KEYSET (See Figure 2–13)
•
•
•
•
•
•
•
Built-in speakerphone
Five fixed function keys
3 Inch x 2.25 Color LCD display with twelve
associated soft keys and a scroll wheel
UP/DOWN buttons for digital control of speaker, handset and ringer volumes
Eight selectable ring tones
Navigation key
Built-in 2 port data switch
FIGURE 2-13
ITP-5107S IP KEYSET (See Figure 2–14)
•
•
•
•
•
•
•
32 character display (2 x 16) with three associated soft keys and a scroll key
Built-in speakerphone
7 programmable keys with tri-colored LEDs
Five fixed function keys
UP/DOWN buttons for digital control of speaker,
handset and ringer volumes
Eight selectable ring tones
Desk or wall-mounted
FIGURE 2-14
2.4.5 OfficeServ™ SOFTPHONE
Samsung OfficeServ™ Softphone is a software-based application that turns your computer into a full-featured
Samsung IP telephone. It is installed directly onto your laptop or desktop PC running Microsoft Windows XP or
2000 operating system. Once a USB headset or a USB handset is connected; the Softphone delivers virtually identical functionality as the ITP-5112 L and ITP-5121D desktop ITP phones. OfficeServ™ Softphone is ideal for
telecommuter and mobile users. Remote workers can simply connect their laptop to the corporate network, snap
in a USB headset, and function as if they were in their own office. They can place, receive, and handle calls on both
the internal and external network, providing a truly portable and practical solution.
2.14
2.4.6 OfficeServ™ Wireless
MGI/DUAL-BAND AP SOLUTION
WIRELESS DUAL-BAND ACCESS POINT (SMT-R2000)
(See Figure 2–15)
The wireless access point (SMT-R2000) provides
wireless coverage to the building. It supports IEEE
802.11a/b/g WLAN standard for both voice and
data. It gives voice packets priority over data packets. The quality of the service for voice is always
guaranty.
FIGURE 2-15
Highlights of SMT-R2000 Features
•
•
•
•
•
•
•
•
•
•
•
Two radios WLAN access point. Radio 1: 5GHz IEEE 802.11a (54 Mbps) and Radio 2: 2.4 GHz IEEE 802.11b/g (54
Mbps)
8 voice calls per AP
Wireless data stations or handsets associated per AP, 802.11a: 255, 802.11b/g: 255. Total: 510
Wireless access point or repeater mode
RP-SMA type connector for external antenna
Support router mode
Enhanced security mode (WEP, WPA, WPA2, etc.)
Support PoE (Power over Ethernet)
Easy Web Management
Wi-Fi certified
No MGI channel required for conversation between handset to handset or handset to ITP desktop phone
2.15
WIRELESS INTERNET PHONE (WIP-5000M HANDSETS) (see Figure 2-16)
Wireless Internet Phone (WIP-5000M) is a compact handheld unit
that works within the Samsung OfficeServ Wireless system. The
three ounce handset comes with a rich set of features. Its graphical display and menu-driven function make it very simple to use.
The handset package comes with a handset, battery, a two-hour
fast charging unit, a leather carrying case and a headset with hook
switch control.
Highlights of WIP-5000M Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Caller name and number display
Call Waiting
Voice mail indication
Hot key for voice mail access
System hold
Call transfer
Call forward
Call mute
Call pick up
Do not disturb
Dynamic soft keys
Hard keys for TRANSFER, HOLD, and CONFERENCE
Redial
Pre-dial
Local phone book with room for 64 numbers - alphanumeric.
Hot key for vibrator function (*)
32 call log (incoming & outgoing)
Adjustable volume, 10 different ringer tones and adjustable ringer volume
Hot key for keypad lock/un-lock (#)
Microphone mute key
Talk/standby time 2.5/25 hours
2 hours fast charger
Spare battery slot in charger
Weight 3.2 oz including battery
Support two system registration
Built-in Web server for status monitor and software upgrading
Software upgrade through wireless connection
2.16
FIGURE 2-16
PART 3. SPECIFICATIONS
The following tables provide technical data for the OfficeServ 500 hybrid/key telephone system.
3.1a ELECTRICAL SPECIFICATIONS (PSU 60)
AC INPUT
120 (88—132) VAC (48—63 Hz)*
220 (180—260) VAC (48—63 Hz)
POWER CONSUMPTION (MAX)
120 WATTS MAX. PER PSU, FUSE RATING 3 AMP
BTU RATING (MAX)
6.8 BTU / MINUTE
DC OUTPUT
+5 VOLTS 5.0 AMPS MAX
--5 VOLTS 0.5 AMPS MAX
--48 VOLTS 1.4 AMPS MAXIMUM
--54 VOLTS CHARGER 0.45 AMPS MAX
*Normal factory setting.
3.1b ELECTRICAL SPECIFICATIONS (PSU-B)
AC INPUT
100—120 (88—132) VAC (48—63 Hz)*
220—240 (180—260) VAC (48—63 Hz)
POWER CONSUMPTION (MAX)
150 WATTS MAX. PER PSU, FUSE RATING 5 AMP
BTU RATING (MAX)
8 BTU / MINUTE
DC OUTPUT
+5 VOLTS 8.0 AMPS MAX
--5 VOLTS 1.5 AMPS MAX
--48 VOLTS 1.4 AMPS MAXIMUM
--54 VOLTS CHARGER 0.45 AMPS MAX
*Normal factory setting.
NOTE: Only the PSU-B should be installed in the first PSU slot (left). It is the main source of +5V DC to processor
cards. It will only support 56 stations or SEPUs.The second PSU slot (right) can use either the PSU60 or PSU-B.The
PSU-B will support 64 stations (SEPUs) when used in this slot. The PSU60 will support 56 stations (SEPUs) when
used in this slot.
3.1
3.2 DIMENSIONS AND WEIGHTS
HEIGHT
WIDTH
DEPTH
WEIGHT
17.5”
22.5”
12”
35 lb.
35”
22.5”
12”
70 lb.
Expanded System: Three Cabinets
52.5”
22.5”
12”
105 lb.
iDCS Digital Keyset (18 and 28 Button)
4.25”
8.5”
9”
2.563 lb.
iDCS Digital Keyset (8 Button)
4.25”
6.4”
9”
2.240 lb.
ITP-5121D
4”
10.5”
8.25”
2.340 lb.
ITP-5112L
4”
10.5”
8.5”
2.570 lb.
iDCS 14B Strip
5”
1.625”
8”
5.5 lb.
iDCS 64B AOM
4”
5.25”
9”
1.1 lb.
DS 5021D / DS 5014D
4”
10.5”
8.25”
2.340 lb
DS 5007S / ITP 5107S
4”
9.25”
8.25”
1.9 lb
DS 64B AOM
4”
5.25”
8.25”
1.0 lb
64 Button Add-On Module
4.25”
Door Phone
5”
OfficeServ 500 Basic System: Single Cabinet
Expanded System: Two Cabinets
4.25”
3.88”
9”
1.25”
1.25 lb.
6.8 oz.
3.3 ENVIRONMENTAL LIMITS
OPERATING TEMPERATURE
32—104 °F / 0—40 °C
STORAGE TEMPERATURE
--13—158 °F / --25—70 °C
HUMIDITY
10%—90% Non-Condensing
3.4 CABLE REQUIREMENTS
EQUIPMENT
CABLE
AWG
MAX FEET
MAX METERS
DIGITAL KEYSET
1 PR. TWISTED
24
1300
400
ADD-ON MODULE
1 PR. TWISTED
24
1300
400
SINGLE LINE STATION
1 PR. TWISTED
24
3000
1 KM
DOOR PHONE
2 PR. TWISTED
24
330*
100
2 PR. CAT 5
22
330*
100
ITP KEYSET
*This is the maximum distance a door phone can be from the DPIM. The DPIM can be up to 900 cable feet from
the KSU. The total distance must not exceed 1230 feet.
3.2
3.5 SYSTEM TONES
TONE
FREQUENCIES
CADENCE
DIAL TONE
350 + 440 Hz
Continuous
RINGBACK TONE
440 + 480 Hz
1 sec on + 3 sec off
DID RINGBACK TONE
440 + 480 Hz
2 sec on + 4 sec off
BUSY TONE
480 + 620 Hz
0.5 sec on + 0.5 sec off
DND / NO MORE CALLS
480 + 620 Hz
0.25 sec on + 0.25 sec off
TRANSFER / CONF
350 + 440 Hz
0.1 sec on + 0.1 sec off
CONFIRMATION TONE
350 + 440 Hz
0.05 sec on + 0.05 sec off
ERROR TONE
480 + 620 Hz
0.05 sec of tone 1/0.05 sec of tone 2
SYSTEM TONES
Intercom Dial Tone—A steady tone that indicates you can begin dialing.
DIAL TONE
CONTINUOUS
Ringback Tone—Indicates the station you dialed is ringing.
RINGBACK TONE—1000 ms ON/3000 ms OFF
CONTINUOUS
Busy Signal—Indicates the station you dialed is busy.
BUSY TONE—500 ms ON/500 ms OFF
CONTINUOUS
DND/No More Calls Tone—Fast busy tone advises you the station you dialed is in the Do Not Disturb mode or
cannot receive any more calls.
DND/NO MORE CALLS TONE—250 ms ON/250 ms OFF
FOR TEN SECONDS
3.3
Transfer/Conference Tone—Indicates your call is being held and you can dial another party.
TRANSFER/CONF TONE—100 ms ON/100 ms OFF
CONTINUOUS
Confirmation Tone—Very short beeps followed by dial tone indicate you have correctly set or canceled a system
feature.
CONFIRMATION TONE—50 ms ON/50 ms OFF
FOR TWO SECONDS
ERROR TONE—A distinctive two level beeping tone indicates you have done something incorrectly.Try again.
ERROR TONE—50 ms of tone 1/50 ms of tone 2
FOR TWO SECONDS
3.6 KEYSET LED INDICATIONS
CONDITION
LED COLOR
LED ON
LED OFF
OFF
—
OFF
RED / GREEN
STEADY
—
AMBER
500 ms
500 ms
RED / GREEN
500 ms
500 ms
RINGING C.O. CALL
GREEN
100 ms
100 ms
RINGING INTERNAL CALL
GREEN
100 ms
100 ms
DND INDICATION
RED
112 IPM for 500 ms
500 ms
OPERATOR CALLS
RED
100 ms
100 ms
ANS / RLS (DND)* (**)
RED
112 IPM for 500 ms
500 ms
ANS / RLS (HANDSET MODE)**
RED
STEADY
—
TRSF (FORWARD ALL)**
RED
STEADY
—
LINE IDLE
LINE IN USE
RECALL
CALL ON HOLD
*Overrides headset mode
**DCS model keysets only
3.4
3.7a RESERVE POWER DURATION ESTIMATES (in minutes)*
UPS CAPACITY IN VOLT AMPS (VA)
No. of PSUs
250
450
600
900
1250
2000
5
20
30
47
75
180
2
8
10
24
40
70
3
5
7
20
36
64
4
13
22
35
5
10
13
25
6
5
10
20
1
*These are approximate values. Specific UPS devices, due to their internal construction, can have greater or lesser values.
3.7b RESERVE POWER DURATION ESTIMATES (in hours)*
BATTERY CAPACITY IN AH
No. of PSUs
40
80
120
160
200
240
1
15
x
x
x
x
x
2
7.5
15
x
x
x
x
3
5.3
7.5
15
x
x
x
4
4
5.3
7.5
15
x
x
5
3.2
4
5.3
7.5
15
x
6
2.7
3.2
4
5.3
7.5
15
*These are approximate values. Specific batteries, due to their internal construction, can have greater or lesser values. Note: X denotes that this system configuration cannot charge batteries of this capacity.
3.5
Samsung OfficeServ 500 Table Size Comparison
M
VERSION
L
VERSION
CID Abandon Lists
100
100
30
CID Name Translation Entries
1000
2000
20
20
Call Buttons per Station
8
8
Station Group Members
48
48
Call Logs Entries
2000
2000
Unconditional Group Members
32
32
Call Log per Station
50
50
Trunk Group Members
99
99
Tenant Groups
2
2
Internal Page Members
99 x 5
99 x 5
Ring Plans
6
6
External Page Members
8x4
8x4
Programmed Messages
20 (15+5)
20 (15+5)
Toll Restriction Entries
500
500
AOM Pairs per Station
4
4
Toll Allowance Entries
500
500
Call Cost Digit Entries
500
500
DID Translation Entries
999
999
Call Cost Rate Tables
8
8
Authorization Code Entries
500
500
PBX Access Code Entries
5
5
Account Code Entries
999
999
Special Code Entries
10
10
Station Groups
40
80
8
8
LCR Digit Entries
2000
2000
Emergency/Override Code
Entries
LCR Modify Digit Tables
200
200
Holiday Entries
60
60
LCR Time Tables
4
4
Class of Service
30
30
LCR Time Bands
4
4
LCR Classes
8
8
LCR Route Tables
32
32
Message Waiting per Station
5
5
Alarm Reminder Buffers
3
3
Conference Groups
24
24
2000
2500
Conference Group Members
5
5
System Buffers (MAX)
500 / 950
500/950
Pickup Groups
99
99
Station Buffers (MAX)
50
50
Internal/External Page Zones
5/4
5/4
AA Plan Tables
12
12
Redial & External FWD Dial Digits
18
18
AA Translation Tables
12
12
IP Keysets
120
240
AA Translation Entries
100 x 12
100 x 12
Virtual Extensions
62
118
2000
2000
10/100
10/100
M
VERSION
L
VERSION
Station Groups
40
80
Trunk Groups
30
UCD Groups
Speed Dial Entries
CID Review Buffers
Text Messages
3.6
PART 4. BUSINESS FEATURE PACKAGE
SYSTEM FEATURES
Account Code Entry
OfficeServ™ EasySet
Caller ID Features
Forced - Verified
Name/Number Display
OfficeServ™ Call
Forced - Not Verified
Next Call
OfficeServ™ Operator
Voluntary
Save Caller ID Number
Account Code Key
Store Caller ID Number
Account Code Key - One Touch
Inquire Park/Hold
Add-On (5 Party)
Administrator Program Key
Caller ID Review List
Unsupervised
All Call Voice Page
Investigate
Attention Tone
Abandon Call List
Conference Group
Audio Message with Alarm
Caller ID on SMDR
Customer Set Relocation
Number to Name Translation
Data Security
Caller ID to PSTN
Database Printout
Caller ID to Analog Port
Daylight Saving Time-Automatic
(Timer) Reminder
Authorization Codes
Forced
OfficeServ™ Softphone
Conference
Split
Dialed Number Identification Service (DNIS)
Voluntary
Call Forwarding
Auto Answer on CO
All Calls
Direct In Lines
Auto Attendant†
Busy
Direct Inward Dialing (DID) T1/Copper
Automatic Call Distribution (ACD)
No Answer
Day/Night Routing
Automatic Hold
Busy/No Answer
Busy or Camp-On Option
Background Music
Forward DND
MOH Source
Branch Group
Follow Me
DID Call Limits
Call Activity Display
External
Direct Inward System Access (DISA)
Call Center
To Voice Mail
Direct Trunk Selection
Preset Destination
Directory Names
Preset Forward Busy
DISA Security
Agent Busy/Manual Wrap-Up Key
Agent PIN (ID) Numbers
Agent Login & Logout
Distinctive Ringing
Call Hold
Automatic Logout
Exclusive
Door Lock Release (Programmable)
Automatic Wrap-Up Timer
System
Door Phones
Remote
E & M Tie Lines T1/Copper
Priority Call Queuing
Embedded Reporting Package
Agent Statistics
Executive Barge-In (Override)
Call Park and Page
Call Pickup
Call Statistics
Directed
Group Supervisors
Groups
Printed Reports
Established
With Warning Tone
Without Warning Tone
Trunk Monitor or Service Observing
External Music Interfaces
Call Recording
External Page Interfaces
UCD Statistics
Call Waiting/Camp-On
Flash Key Operation
UCD Monitoring
Caller Emergency Service ID (CESID)
Flexible Numbering
Wall-Style Display Windows
Centrex/PBX Use
Ground Start Trunks (T1/Copper)
Call Costing
Chain Dialing
Group Busy Setting
Caller Identification†
Chain Forward
Hot Line
Automatic Number Identification (ANI)
Class of Service
In Group/Out of Group
Caller ID
Common Bell Control
Incoming Call Distribution
Calling Line Identification (CLI)
Computer Telephony Integration (CTI)
Incoming/Outgoing Service
OfficeServ DataView
OfficeServ™ Link
Individual Line Control
OfficeServ™ DataView
IP Keysets
4.1
Park Orbits
Tenant Services (2)
Primary Rate Interface (PRI)
Prime Line Selection
Toll Restriction
Basic Rate Interface (BRI)
ISDN Service
Priority Call Queuing
By Day or Night
LAN Interface
Private Lines
By Line or Station
Least Cost Routing
Programmable Line Privacy
Eight Dialing Classes
Live System Programming
Programmable Timers
Special Code Table
From any Display Keyset
Recalls
Toll Restriction Override
With a Personal Computer
Recall to Operator
Tone or Pulse Dialing
Meet Me Page and Answer
Redial Review
Traffic Reporting
Memory Protection
Remote Programming—PC
Transfer
Message Waiting Indications
Ring Modes
Screened/Unscreened
Message Waiting Key
Time Based Routing–Plans
Microphone On/Off per Station
Automatic / Manual
Mobility Solution
Holiday Schedule
Trunk Groups
Multiple Language Support
Temporary Override
Uniform Call Distribution (UCD)†
Voice Mail Transfer Key
With Camp-On
Music on Hold—Flexible
Ring Over Page
Universal Answer
Music on Hold—Sources
Secretary Pooling
Virtual Extensions
Networking
Single Line Connections
Voice Mail
QSIG over IP
Speed Dial Numbers
QSIG over PRI
Station List
Off Premises Extensions (OPX)
Inband Signalling
Integrated (In-Skin)
System List
VoIP
Operator Group
Speed Dial by Directory
Walking Class of Service
Overflow
Station Hunt Groups
Wireless Handsets—See Mobility Solution
Operator
Distributed
Station Group
Sequential
Override Codes
Paging
Unconditional
Station Message Detail Recording (SMDR)
Internal Zones (5)
Station Pair
External Zones (4)
System Alarms
All External
System Maintenance Alarms
Page All
System Directory
†Requires optional hardware and/or software. Ask your dealer for details.
4.2
4.1 SYSTEM FEATURE DESCRIPTIONS
ACCOUNT CODE ENTRY
Station users may enter an account code (maximum 12 digits) before hanging up from a call. This account
code will appear in the SMDR printout for that call record. Keyset users may enter this code using an account
code key without interrupting a conversation. Single line telephone users must temporarily interrupt the call
by hook-flashing and dialing the feature access code. Manually entered account codes can be up to 12 digits long. In some cases users can be forced to enter an account code and this account code may or may not
be verified as described below.
Forced – Verified
When set for this option the user must enter an account code for all outgoing calls.The account code entered
will be verified from a system list of 999 entries. Forced Verified codes can contain the digits 0~9.
Forced - Not Verified
When set for this option the user must enter an account code for all outgoing calls, but the account code is
not verified against the system list. Non verified account codes can contain the digits 0~9, * and #.
Voluntary
In this case account codes are not required to make outgoing calls but may be used if desired.This is also the
method used to assign an account code to incoming calls. These account codes can contain the digits 0~9, *
and #.
ACCOUNT CODE KEY
The account code (ACCT) key can be programmed on any keyset and will appear as a soft key on display keysets. This key allows the user to enter account codes without interrupting a call.
ACCOUNT CODE KEY – ONE TOUCH
The account code (ACC) key can be programmed on any keyset. This key can be programmed with an extender and operates in three different ways depending on the extender as follows.
Extender = 000
When programmed with an extender of 000 the user will be prompted to enter an account code when the
key is pressed.
Extender = 001~999
When programmed with an extender ranging from 001 to 999 the key will, when pressed, automatically
insert the account code contained in that bin of the system account code list. This is known as One Touch
account codes.This option can be denied in system programming to prevent users from bypassing the security of system account codes.
No Extender
When programmed without an extender the key will, when pressed, prompt the user to enter the bin number the system account code table where the account codes are stored.
4.3
ADMINISTRATOR PROGRAM KEY
This feature gives designated stations the ability to administer a number of System functions from their keyset using a flexibly assigned button. The Administrator Program (PROG) key is programmed in MMC 722. The
station passcode must be changed from the default value to use this feature. See the System Administrator
Guide for more information.
ALL CALL VOICE PAGE
Users can page internal zone zero and all external paging zones at the same time by dialing the All Page code.
Keysets may be restricted from making or receiving pages in system programming. A maximum of 99 keysets
can be programmed in each internal page zone to receive page announcements.
Note: Each IP keyset being paged requires an MGI channel to carry the page audio. If all MGI channels are
busy then no IP keysets will receive a page.
ATTENTION TONE
To get your attention, a brief tone precedes all page announcements and intercom voice calls. There are separate programmable duration timers for page and voice announce tones.
AUDIO MESSAGE WITH ALARM (TIMER) REMINDER
This feature provides an option that allows a recorded message to be played to a user when they go off hook
to answer an alarm reminder ring (timed reminder ring).The message is recorded on the AA card. In addition,
if the AA group is busy when the reminder call is answered the system will play a designated MOH source to
the user. Alternatively System programming can define an external music source to be played when the
Appointment Reminder is answered.
AUTHORIZATION CODES
Authorization codes are used to give permission to make a call. A maximum of 500 four to ten-digit authorization codes can be either forced or voluntary.When used, authorization codes will automatically change the
dialing station’s class of service to the level assigned to the authorization code. Authorization codes may be
programmed to print or not print on SMDR.
Forced
When a station is programmed for forced authorization, the user must always enter this code before dialing
is allowed. The dialed authorization code is verified from the system list of 500 authorization codes.
Voluntary
Any station user can always enter an authorization code before they begin dialing. The dialed authorization
code is verified from a system list of 500 authorization codes.
AUTO ANSWER ON CO
Allows new CO calls directed to a certain keyset to auto answer and be in the call announce mode.This means
that private lines and DID calls can be “auto answered” in the same manner as intercom calls.Transferred calls
and calls to a station group of which that keyset is a member will continue to ring.
AUTO ATTENDANT
The integrated digital automated attendant feature (AA) provides eight ports per card for simultaneous
answering and call processing. A maximum of five cards can be installed in one system. Each card has sixteen
professionally recorded announcements inform callers of the progress of their calls. Several examples are the
4.4
following:“I’m sorry. There is no answer”,“That station is busy”, and “Invalid Number. Please try again”. A maximum of two minutes of super capacitor backed (100 hours) random access memory (RAM) provide up to 48
customer recordings for announcements or greetings. Twelve individual announcements (boxes), each with
its own dialing options, allow you to build call routing branches as needed. Callers are routed through the
branches by dialing extension numbers or single digits. This system is compatible with SVM and CADENCE.
NOTE: Announcements recorded on one AA card can not be played to callers on another AA card.
AUTOMATIC CALL DISTRIBUTION (ACD)
ACD is a call distribution method by which callers in a queue are routed to the next available agent. While
waiting in a queue a canned or customized announcement can be periodically played to the caller based on
a programmable timer while retaining their place in the queue. Statistical and historical reports are available
to assist supervisors in managing a call center. See Call Center.
AUTOMATIC HOLD
While a keyset user is engaged on an outside (C.O.) call, pressing another trunk key, route key or CALL button
automatically places the call on hold when Automatic Hold is enabled. Pressing TRSF, CONFERENCE, PAGE or
a DSS key always automatically places a C.O. call on hold. Intercom calls can be automatically held only by
pressing TRSF or CONFERENCE. Each keyset user can enable or disable Automatic Hold.
BACKGROUND MUSIC
Keyset users may choose to hear music through their keyset speakers when optional external sources are
installed. Each user may adjust this level by the use of a volume control program at the selected keyset.
BRANCH GROUP
This feature allows stations included in a branch group to answer a ringing call to another station in the
group by simply lifting the handset or going on speakerphone mode.This feature works well when there is a
need to answer calls for people who may be away from their desk or when a common answering pool is
needed. Calls can be directed to a common bell and then can be answered by anyone in the Branch Group.
There are a total of 99 branch groups available, but a station can only be in one branch group.
CALL ACTIVITY DISPLAY
The OfficeServ 500 will record and buffer all calling activity within the system. With a Call Activity Display
(CAD) key, the OfficeServ 500 will display a “snapshot” of the following information:
•
•
•
•
•
•
The maximum number of ports that have been used
The maximum number of trunks that have been used
The maximum number of stations that have been used
The current number of ports in use
The current number of trunks in use
The current number of stations in use
CALL CENTER
ACD/UCD Call Centers are required when the user expects to have more ringing calls then people (agents) to
answer them. This functionality prevents callers from receiving busy signals or lengthy ring delays before
answering. Callers reaching a busy group with no available agents are held in queue for the next available
agent. First and second announcements reassure the caller until an agent becomes available.
The OfficeServ 500 can have 20 simultaneous ACD/UCD groups with a maximum of 48 agents per group. Any
time there are one or more calls in queue and no available agents, the longest waiting call will automatically
4.5
be distributed to the next available agent. When there are no calls in queue the next new call will be routed
to the next idle agent according to a specified distribution method.
There are two available reporting options to support the [system] call center functionality. The embedded
basic reporting package included with the telephone system is ideal for small informal call center solutions
as it provides simple ACII text reports to a customer provided LAN printer, as well as informational displays at
a supervisor’s display telephone. The more sophisticated call center may require the optional OfficeServ
DataView CTI application that provides historical reporting, agent and call monitoring and wallboard displays.
NOTE: Some features require optional hardware or software. Ask your authorized Samsung Dealer for details.
Agent Busy / Manual Wrap-Up Key
This UCD group feature allows an agent to have a programmed button that when depressed will remove the
keyset from free status within the group. The agent can depress the button again to return the keyset to free
status. This provides a method for agents to manually extend their wrap-up time when necessary. This also
allows agents to perform other duties such as receiving or making telephone calls without having to log out
of the group.
Agent PIN (ID) Numbers
When desired this feature allows agents to be assigned a PIN number to use when logging in and out of a
UCD group.This allows an agent to move from location to location and retain their productivity records.There
are a total of 300 PIN numbers available in the system.
Agent Login & Logout
At any time agents may login or out of a station call group by dialing an access code or simply pressing the
IOG button for the selected group. A red LED on the IOG button indicates you are in the group.
Automatic Logout
This feature allows the system to further limit ringing delays by automatically logging out stations that are
unattended. If a call is delivered to a station that does not answer after a programmable number of rings, the
station is automatically logged out of the group so that no further call attempts will be made until the agent
has logged back in.
Automatic Wrap-up Timer
The wrap-up timer prevents calls to an agent for a programmable period of time. This allows the agent to finish up paper work associated with the last call.
Priority Call Queuing
This feature places calls to a station queue ahead of other calls based on priority level (1-9).The system compares the DID number, Caller ID, or trunk ID to a preprogrammed table and assigns the call a corresponding
priority that places it in the appropriate position in the queue. This functionality is ideal when specific customers require special treatment.
EMBEDDED REPORTING PACKAGE
The OfficeServ 500 system provides some basic reports and statistics available to a supervisor using a display
keyset. These features can be used in conjunction with, or independently of, the OfficeServ™ DataView
reporting and monitoring package.
4.6
Agent Statistics
UCD supervisor positions using a display keyset can monitor the number of agents in a group and how many
agents are currently logged in. Each station’s status can be reviewed for the number of calls answered and
the average call length for the day.
Call Statistics
UCD supervisor positions using a display keyset can monitor the number of calls in queue, the longest wait
time for calls currently in queue, the average wait time for the day, and the total number of calls answered for
the day.
Group Supervisors
Multiple supervisors can be assigned to each group and one station can be given supervisor status for multiple UCD groups.The group supervisor (using a display keyset) can log agents in and out of the group in real
time to help manage the workload.
Printed Reports
UCD supervisor positions using a display keyset may run printed reports to a customer-provided printer,
showing the data available from the supervisor displays. These reports can be run manually or scheduled to
run at specific intervals.
OFFICESERV DATAVIEW
For users who require more power than the embedded reports can provide, the web-based OfficeServ™
DataView CTI application can be used for enhanced reporting and monitoring functionality. See separate
DataView Literature for more details.
UCD Statistics
OfficeServ™ DataView provides over a dozen different historical reports to provide detailed statistics on call
volume and call times as well as agent activity. Also included is a detailed Abandoned Call list to define each
lost call to the UCD group.
UCD Monitoring
OfficeServ™ DataView provides several different monitoring interfaces that allow users to easily see live connection status and port activity for UCD groups and agents.
Wallboard-Style Display Windows
OfficeServ™ DataView is equipped with a series of wallboard-style displays which allow quick and easy visibility of live call status information about the group, such as longest wait time, calls in queue, agents busy,
and more. This information can display as a personal PC Wallboard on an agent’s monitor. When used in conjunction with customer provided large screen display, such as an LCD or plasma monitor (TV), these same
wallboard windows can provide this data to the entire call center from a greater distance with a level of clarity and flexibility that isn’t possible with traditional LED wallboards.
CALL COSTING
The OfficeServ 500 software provides programmable call costing tables to calculate the cost of incoming and
outgoing calls. Rates are calculated by the number dialed, and may include surcharges. Display keysets can
be set to show the call duration timer or the call cost. The SMDR report will show either the call duration or
the call cost depending on the station selection. One call handled by multiple callers will cost each call segment separately.
4.7
CALLER IDENTIFICATION
The OfficeServ 500 supports three methods of identifying an incoming caller depending on the circuit type
as described below.
Automatic Number Identification (ANI)
On a digital T1 trunk programmed as E&M trunks calling party information is called ANI. This information is
the telephone number of the calling party and is sent as in-band DTMF digits during the call setup. Care
should be taken to ensure the system has sufficient DTMF receiver resources to handle the expected volume
of call traffic. Although ANI provides the number only, a name can be attached to the telephone number of
frequent callers via the CID/ANI translation table.
Caller ID
On an analog, loop start CO line, calling party information is called Caller ID and is available from the telephone company in two formats, Number only and Name and Number, sometimes called Deluxe. The
OfficeServ 500 is compatible with both formats. Even if the telephone company only offers the number only,
a name can be attached to the telephone number of frequent callers via the CID/ANI translation table.
Calling Line Identification (CLI)
On ISDN circuits, calling party information is called CLI and is supported on both BRI and PRI type circuits as
described below.
BRI
On BRI circuits the OfficeServ 500 only supports Number delivery and, like ANI, a name can be attached
to the telephone number of frequent callers via the CID/ANI translation table.
PRI
On 5ESS and NI2 PRI circuits both name and number support is provided on the OfficeServ 500 system.
On a DMS100 circuit only Number service is provided.
CALLER ID FEATURES
The following features apply to all forms of Caller Identification, however, to make them easier to read caller
identification is referred to as Caller ID.
Name/Number Display
Each LCD keyset user can decide if he/she wants to see the name or number in the display. Regardless of
which one is selected to be seen first, the NND key is pressed to view the other pieces of information.
Next Call
In the event that you have a call waiting or a camped-on call at your keyset, you can press the NEXT key to
display the Caller ID information associated with this next call in queue at your station. Either the Caller ID
name or number will show in the display depending on your selection.
Save Caller ID Number
At any time during an incoming call that provides Caller ID information, you may press the SAVE key. This
saves the Caller ID number in the Save Number feature. Pressing the SAVE number redial key will dial the
Caller ID number. The system must be using Least Cost Routing (LCR) to dial the saved number.
4.8
Store Caller ID Number
At any time during an incoming call that provides Caller ID information, you may press the STORE key. This
saves the Caller ID number as a speed dial number in your personal speed dial list.The system must be using
LCR to dial the stored number.
Inquire Park / Hold
Having been informed that an incoming call is on hold or has been parked, you may view the Caller ID information before you retrieve the call. This will influence how you choose to handle the call.
Caller ID Review List
This feature allows display keyset users to review Caller ID information for calls sent to their stations. This list
can be from ten to fifty calls in a first in, first out basis. The list includes calls that you answered and calls that
rang your station but that you did not answer. When reviewing this list, you can press one button to dial the
person back.The system must be using LCR to dial the stored number.There is also an option called CID REVW
ALL in the User ON/OFF options. When set to ON the feature will operate the same as described. However,
when set to OFF only calls that are not answered (missed calls) at the station will be recorded in the Review
list.
Investigate
This feature allows selected stations with a special class of service to investigate any call in progress. If Caller
ID information is available for an incoming call, you will know to whom this station user is speaking. On outgoing calls, you can see who was called. After investigating, you may barge-in on the conversation, disconnect the call or hang up.
Abandon Call List
The system has a system-wide abandon call list that stores Caller ID information for calls that rang but were
not answered. The list is accessed using the administrator’s passcode. When reviewing this list, you are provided options to CLEAR the entry or DIAL the number.You can see the NND key to toggle between the Caller
ID name, number and the date and time the call came in.The system must be using LCR to dial numbers from
the abandon call list. The abandoned call list will store up to 100 unanswered calls.
Caller ID ON SMDR
The Station Message Detail Records report can be set to include Caller ID name and Caller ID number for
incoming calls. This format expands the printout to 113 characters. Use a wide carriage printer or an 80 column printer set for condensed print.
Number to Name Translation
The system provides a translation table for 1000 entries on OfficeServ 500-M version software and 2000
entries on OfficeServ 500-L version software. When the Caller ID number is received, the table is searched.
When a match is found, the system will display the corresponding name.
Caller ID to PSTN
When calling out on ISDN-PRI services, each station can be programmed to send any one of the listed directory numbers provided on the PRI circuit. Examples are: the main number, another number or an individual
DID number. (PSTN=Public Switch Telephone Network)
Caller ID to Analog Port
When equipped with the optional RCM2 card, Caller ID from the telephone company is sent to analog ports
within the system.
4.9
CALL FORWARDING
This feature allows the user to redirect (forward) incoming calls. The calls can be redirected to the attendant,
a hunt group, voice mail, external number or another station user. If the destination station is in Do Not
Disturb (DND), the calling party will receive DND/Reorder tone. Calls cannot be forwarded to a door phone.
All Calls
This type of forwarding is not affected by the condition of the station. All calls are immediately redirected to
the designated destination. If desired, the destination station may redirect the call back to the forwarded station by using the transfer feature.The forwarded station user can continue to originate calls as usual. If no key
is programmed as Forward All, the TRSF key lights steady when a Forward All condition is set.
Busy
This feature forwards all calls only when the station set is busy. The station user can originate calls as usual.
No Answer
This feature forwards calls that are not answered within a preprogrammed time. The user can originate calls
as usual and receive call if present. The timer is programmable on a per-station basis to allow for differences
in individual work habits.
Busy /No Answer
This feature allows the station user to use both types of forwarding simultaneously, provided the destinations
have already been entered in the usual manner.
Forward DND
This feature works with the Do Not Disturb feature.This allows calls directed to a station in Do Not Disturb or
One Time Do Not Disturb to forward immediately to another destination.
Follow Me
This feature allows the user to forward all calls from another station to the user’s station or change the forward destination to the user’s current location.
External
Stations can be programmed to forward all, forward busy, forward no answer, forward DND C.O. calls to an
external number via a central office trunk if allowed by class of service. Intercom calls may also be programmed to forward to an external number via a central office trunk.
To Voice Mail
Each station may be programmed to allow or deny the ability to forward intercom calls to voice mail. When
denied, valuable message time in the voice mail system can be saved.
Preset Destination
If desired this feature provides for a permanent (preset) forward no answer destination for each extension. It
can only be programmed by the system technician or system administrator. When any station does not have
FWD/NO-ANSWER set, the call will ring this preset destination if one is programmed.
Preset Forward Busy
This feature allows the Preset Forward No Answer setting to also work for Busy status. When PRESET BUSY is
turned on the calls will follow the preset for both busy and no answer conditions.
4.10
CALL HOLD
Exclusive
Outside calls can be placed on exclusive hold at any keyset by pressing HOLD twice during a call. Calls placed
on exclusive hold can only be retrieved at the keyset that placed the call on hold. Intercom calls are always
placed on exclusive hold. Exclusive hold for trunk calls can be denied in class of service.
System
Outside calls can be placed on system hold at any station. Users may dial the access code or press the HOLD
button. Calls on system hold may be retrieved at any station.
Remote
Outside calls can be placed on hold at a station other than the station placing the call on hold. This feature
allows calls to be answered at one keyset and placed on hold at another station. This allows time for the user
to proceed to that station or allows the party that the call was intended for to have that call placed at their
station. The call or trunk button will flash at the remote hold station. NOTE: Intercom calls cannot be remote
held.
CALL PARK AND PAGE
Each C.O. line has its own park zone. This simple method eliminates confusion and ensures that a park zone
is always available. Pressing the PAGE key parks the call automatically.There are no extra buttons to press and
there is no lost time looking for a free zone.
CALL PICKUP
Directed
With directed call pickup, users can answer calls ringing at any station by dialing a code plus that station’s
extension number or by pressing the feature button and then dialing the extension.There is a system option
to allow a DSS key to perform a pickup function rather than a transfer function when pressed.
Groups
In addition, calls can be picked up from a station group in a similar manner. The group pickup feature allows
users to answer any call ringing within any pickup group.There are 99 pickup groups available in the system.
A station cannot be in more than one pickup group. To use this feature, station users either dial the access
code or press the assigned feature button followed by the pickup group number.
Established
This feature enables a keyset user to pick-up an establish call in progress at a single line extension connected to a modem on a PC. An EP key with this extension number must be programmed on the keyset.
Established call pickup is useful with PC dialing programs that outdial from a large list of telephone numbers.
Let the computer dial for you, then press the EP key to speak with the called party.
CALL RECORDING
When using Samsung’s proprietary SVMi in-skin voice mail system, keyset and OfficeServ Softphone users
can record their telephone conversations in their personal mailbox for playback or e-mail later.
CALL WAITING/CAMP-ON
Busy stations are notified that a call is waiting (camped-on) when they receive a tone.The tone is repeated at
a programmable interval. Digital keysets receive an off-hook ring signal through the speaker while single line
4.11
stations and IP keysets receive a tone in the earpiece of the handset.The volume of the camp-on tone can be
set by the station user. Camped-on calls follow Forward No Answer if a Forward No Answer destination has
been set.
Optionally any station can be programmed to automatically camp-on to a busy station instead of having to
press the camp-on button or dial a camp-on code.
CALLER EMERGENCY SERVICE ID (CESID)
This is a service where the telephone system sends a number, usually a call back number, to the Public Service
Answering point (PSAP) when a station user dials 911. This number is associated in the PSAP with a location
indicating exactly where the call originated. This allows the emergency services to respond directly to the
correct building or floor of a building rather than to have to make inquiries as to the location of the emergency. This service is sometimes referred to as Enhanced 911 or E-911. This service is provided in two forms
in the OfficeServ 500, either via a dedicated 4 port Centralized Automatic Message Accounting (CAMA) trunk
card called the E911 card or via an ISDN PRI circuit configured for both way DID connected to the
TEPRI/TEPRIa card.
CENTREX/PBX USE
CENTREX and PBX lines can be installed in lieu of central office trunks. CENTREX and PBX feature access codes
including the command for hook-flash (FLASH) can be stored under one touch buttons. Toll restriction programming can ignore PBX or CENTREX access codes so that toll calls can be controlled when using these
services.
CHAIN DIALING
Keyset users may manually dial additional digits following a speed dial call or chain together as many speed
dial numbers as are required.
CHAIN FORWARD
The chain forward option determines whether a forwarded intercom call that subsequently forwards to
voicemail will target the original stations mailbox or the second stations mailbox.
CLASS OF SERVICE
The system allows a maximum of 30 station classes of service. Each class of service can be customized in
memory to allow or deny access to features and to define a station’s dialing class. Each station can be
assigned different classes of service for day and night operation.
COMMON BELL CONTROL
The MISC daughter board provides relays that may be programmed to control a customer-provided common
bell or common audible device. These contacts must be programmed as members of a station group and
may provide steady or interrupted closure.
COMPUTER TELEPHONY INTEGRATION (CTI)
Computer Telephone Integration (CTI) allows integration between the OfficeServ 500 and a personal computer (PC) on a local area network (LAN). Caller ID service is required for TAPI inbound call applications that
use the CID information to display computer records in conjunction with the presentation of the call to the
station on the OfficeServ 500.
4.12
OfficeServ™ Link
Samsung’s proprietary CTI Server Application that manages all call control functions between the OfficeServ
500 Main Processor and all OfficeServ™ CTI Applications.
OfficeServ™ DataView
OfficeServ DataView is a web enabled Call Center and system traffic reporting package. The DataView application provides live connection status and features usage statistics as well as a wide variety of detailed historical reports. The DataView application server runs on Microsoft IIS web server software, which is included
in Windows 2000, XP Professional and 2003.
OfficeServ™ EasySet
OfficeServ EasySet is a web enabled application that allows keyset customization from virtually any location.
The EasySet application server runs on Microsoft IIS web server software, which is included with Windows
2000, XP Professional, and 2003.
OfficeServ™ Call
OfficeServ Call is a call manager application with support for contact management, inbound screen pop, outbound dialing via the desktop, scheduling, and call logging, as well as providing access to some digital telephone facility programming. OfficeServ Call is a client server based application that supports both an enduser (GUI) interface and industry standards such as TAPI. The client application has support for a wide range
of operating systems including Windows 2000 and Windows XP.
OfficeServ™ Operator
OfficeServ Operator is a PC-based attendant console that works in conjunction with either a TDM or IP Keyset.
OfficeServ Operator can support up to 20 OfficeServ Operators Consoles simultaneously.
OfficeServ™ Softphone
Samsung OfficeServ Softphone is a software-based application that turns your computer into a full-featured
Samsung IP telephone. It is installed directly onto your laptop or desktop PC running Microsoft Windows
operating system. Once a USB headset or a USB handset is connected; the Softphone delivers virtually identical functionality as the ITP-5112 L and ITP-5121D desktop ITP phones. OfficeServ Softphone is ideal for
telecommuter and mobile users. Remote workers can simply connect their laptop to the corporate network,
snap in a USB headset, and function as if they were in their own office. They can place, receive, and handle
calls on both the internal and external network, providing a truly portable and practical solution.
CONFERENCE
The system allows six simultaneous conferences up to 5 parties each. If a SCM daughter board is installed,
then the system allows a total of 24 simultaneous conferences up to 5 parties each.
Add-On (5 Party)
Any combination of up to five parties (stations or outside lines) can be joined together in an add-on conference. Parties may be eliminated or added after a conference has been established.
Unsupervised
A station user may set up a conference with two or more outside lines and then exit the conference leaving
the outside lines connected in an unsupervised (trunk to trunk) conference.
Split
A keyset user can “split” a conference into separate outside calls, then speak with each caller privately. Then
the individual calls can be conferenced again in any combination. NOTE:This feature requires individual trunk
buttons and auto-hold must be enabled.
4.13
CONFERENCE GROUP
Users that have a 5112L-ITP large screen keyset or OfficeServ Softphone may have 1-5 conference groups
programmed. Each conference group can have up to 4 parties assigned. They can be extensions in the system or telephone numbers of people outside the system. Press the Conference Group button to call all members of the group at the same time. Status indications appear in the display. Press the corresponding softkey
to drop or call parties as desired (maximum 100 users).
CUSTOMER SET RELOCATION
Customer Set Relocation allows the customer to exchange or swap similar stations in the OfficeServ 500 without wiring changes. All individual station assignments such as trunk ring, station group, station COS, station
speed dial, button appearances, call forwarding, etc. will follow the Customer Set Relocation program.
DATA SECURITY
Single line extensions used with modems and facsimile machines can be programmed so that they will not
receive any system-generated tones that would disrupt data transmissions. In addition, these devices receive
DCS C.O. ringing pattern instead of intercom ring pattern. Devices connected to an SLI card receive a disconnect signal upon termination.
DATABASE PRINTOUT
A copy of the customer database can be obtained by using OfficeServ™ Manager (OSM).This information can
be directed to a printer or the PC screen and may be done either on-site or remotely. A complete database or
specific data blocks may be obtained.
DAYLIGHT SAVING TIME-AUTOMATIC
The system has a table that can be programmed with the daylight savings change dates for up to 10 years.
At 2:00 am on these dates the system will automatically adjust the system clock to match daylight savings
time. If no dates are programmed the clock will not change.
DIALED NUMBER IDENTIFICATION SERVICE (DNIS)
When DNIS service is provided on an incoming E&M trunk the OfficeServ 500 can route calls based on the
numbers received. (See DID)
DIRECT IN LINES
Outside lines may be programmed to bypass the operator(s) and ring directly at any station or group of stations.
DIRECT INWARD DIALING (DID) T1/COPPER
The term Direct Inward Dialing refers to types of digit steered inbound call handling.These are DID, Both Way
DID, Dialed Number Identification service (DNIS) and Direct Dial In (DDI). The OfficeServ 500 supports the
types described below.
DID is an inbound only service where multiple telephone numbers are assigned, usually in blocks of twenty,
to a single circuit or small group of circuits.These circuits can be single pair analog circuits that will terminate
on a DID card. The DID circuit can be a channel on a digital T1 service terminating on an OfficeServ 500
TEPRI/TEPRIa card.
Both way DID is a service that combines DID service with normal outbound local telephone service.This service is provided over E&M tie line circuits. These E&M tie line circuits can terminate on the digital T1 circuit on
an iDCS TEPRI/TEPRIa card.
4.14
Dialed Number Identification service (DNIS) is a feature of 800 or 900 type numbers that allows the number
dialed by the caller to be identified in the telephone system by means of a sequence of DTMF digits (usually
four). This service terminates on E&M tie lines. These E&M tie line circuits can terminate on the digital T1 circuit on an iDCS TEPRI/TEPRIa card.
Direct Dial In (DDI). This is the name given to the above three services when they are provided over an ISDN
PRI circuit.
The OfficeServ 500 has an option to select which MOH source is played to callers to a specific DID number.
DID Call Limits
This option defines the maximum number of simultaneous calls that the system will accept for each DID
number. Any call attempts after the Maximum Call (MC) count has been reached will be rejected and busy
tone returned.
DIRECT INWARD SYSTEM ACCESS (DISA)
Users can call in on specific DISA lines at any time, input a security code and receive system dial tone. Users
can now place internal calls or if permitted, calls using C.O. lines. The caller must have a tone dial phone and
know his/her DISA security code if DISA security codes/passcodes are turned on. DISA lines can be used as
both way lines or incoming only and may be allowed or disallowed for any of the 6 ring plan time periods.
The C.O. lines used for DISA must have disconnect supervision.The requirement to put in a DISA security code
can be disabled if desired.
DIRECT TRUNK SELECTION
Each station can be allowed access to or denied access from a trunk or trunk group by access code when LCR
is activated. When restricted, the station user must use a trunk key or a route key.
DIRECTORY NAMES
Each station, station group and C.O. line may be assigned a directory name (maximum 11 characters). In addition, each personal speed dial number, system speed dial number and entry in the DID translation table may
be assigned a name (maximum 11 characters). These names are displayed during calls with these ports and
in the case of station and speed dial names, can be used to originate calls. See the Dial by Name feature
(Station Features).
DISA SECURITY
Telephone fraud and long distance theft are a serious concern. The OfficeServ 500 provides a strong DISA
security system. If an incorrect DISA passcode is entered repeatedly (as is the case with “hackers”), the DISA
system can be automatically disabled temporarily. Both the number of incorrect passcode attempts and the
time that DISA is disabled are programmable. In addition, all failed attempts to access DISA print on SMDR (if
provided) with a “DE” DISA error flag.
DISTINCTIVE RINGING
The OfficeServ 500 provides distinctive ringing at a station based on selected parameters.
•
•
•
Outside calls have a single ring repeated, while intercom calls have a double ring repeated.
Any trunk or station can be programmed to ring a specific digital keyset with a predefined ring tone (18) or an analog station with a predefined cadence (1-5) selection.
Digital keysets and analog stations may receive distinctive ringing based on the Caller ID number
received or the DID number dialed.
4.15
DOOR LOCK RELEASE (PROGRAMMABLE)
After answering a call from the door phone, users can dial a code to activate a contact closure. This can be
used to operate a customer-provided electric door lock release mechanism. The contact closure timer is programmable from 100–2500 ms.
DOOR PHONES
The door phone interface module (DPIM) provides for connection of a door phone to a DLI port. Pressing the
button on the door phone produces a distinctive ring (three short rings repeated) at the assigned station or
station group. If not answered within a programmable time, the system releases the door phone and stops
the ringing. Stations may call the door phone directly and monitor the surrounding areas. Door phones follow the system ring mode plan.
E & M TIE LINES (T1/COPPER)
Your office can be connected to another office with a tie line. Use it to make calls to stations in the other system. If programming allows, you can access lines in the other system to make outside calls. Tie line calls can
be put on hold, transferred and conferenced in the same way as are other outside calls. Users accessing the
tie line from the other system can get a line in your system and make outgoing calls. These calls can be controlled by assigning a dialing class to the tie line.Your local telephone company may use E&M tie lines to provide DID service. In this case these tie lines can be programmed to follow the DID translation table. See DID.
Translated E & M tie line calls have Ring Plan routing capabilities.
EXECUTIVE BARGE-IN (OVERRIDE)
The feature allows specially programmed stations with a barge-in key to override the automatic privacy of
another station or outside trunk. Programming allows barge-in with or without a warning tone. Stations may
also be programmed as “secure” so that they cannot be barged-in on.
With Warning Tone
When the barge-in with tone option is set, the barging-in keyset has its microphone on and the barged-in on
station receives an override display. A double burst of warning tone sounds and repeats every ten seconds.
This feature does not work from single line sets.
Without Warning Tone
When the barge-in without tone option is set, the barging-in keyset has its microphone muted and the
barged-in on station does not receive an override display. This feature does not work from single line sets.
Trunk Monitor or Service Observing
This feature allows the user who barged-in to retain the trunk call after the original station has hung up.
WARNING: BARGE-IN WITHOUT TONE MAY VIOLATE STATE OR FEDERAL LAWS CONCERNING THE RIGHT TO
PRIVACY. SAMSUNG TELECOMMUNICATIONS AMERICA IS IN NO WAY RESPONSIBLE FOR THE POSSIBLE MISUSE OF THIS FEATURE.
EXTERNAL MUSIC INTERFACES
The OfficeServ 500 MISC card provides two inputs for connecting to customer provided external music
sources. Each cabinet of the OfficeServ 500 can support one MISC card for a total of three cards or six sources
in a maximum sized system. These sources can be used to provide background music, or any of the varied
Music On Hold (MOH) uses.
4.16
EXTERNAL PAGE INTERFACES
The OfficeServ 500 MISC module provides one external page output and two zone control relays. Resources
from added miscellaneous applications modules (MISC) can be combined to provide four external zones.
Multiple relays may be assigned to each zone.
FLASH KEY OPERATION
While a user is on an outside line, pressing the FLASH key will send a timed disconnect signal to the central
office or PBX. This is used for custom calling features on C.O. lines or in conjunction with CENTREX/PBX operation. System programming allows individual flash times for C.O. and PBX lines. When C.O. or PBX flash is not
required, setting the timers for two seconds releases the existing call and returns dial tone to make a new call.
FLEXIBLE NUMBERING
System programming allows stations to have two, three or four digit extension numbers beginning with the
digit 2 or 3. Three digit default extension numbers begin with 201 and four digit defaults begin with 2001.
Station group numbers can be three or four digits beginning with the digit 5.
Using digits other than 2, 3 or 5 will require the technician to change other default feature access codes in
the system default numbering plan. User guides will need to be modified as these are all written using the
OfficeServ 500 default numbering plan.
GROUND START TRUNKS (T1/COPPER)
The OfficeServ 500 can utilize these trunks to support a positive disconnect signal and prevent call collisions
on heavy traffic usage. Caller ID or ANI service is not available on these trunks. Ground start signaling can terminate on the T1 circuit on the iDCS TEPRI/TEPRIa.
GROUP BUSY SETTING
This feature provides a busy signal to intercom callers that ring to a station group when all logged-in stations
are busy. The feature is activated in MMC 601 and when set to ON setting, allows an intercom caller to hear a
busy signal when calling a station group. Upon hearing a busy the intercom caller will know that all stations
are busy and can call back.When this option is set to OFF position the intercom caller will hear ring-back tone
when all stations are busy and the call will queue for the next available station. Turning this option ON will
override the Overflow setting when the group is busy. The default setting is OFF.
HOT LINE
Stations can be programmed to call a pre-defined station or station group whenever that station goes offhook. A hot line delay timer of 0–250 seconds can be programmed to allow sufficient time to make a different call. This timer is programmable on a per station basis.
IN GROUP/OUT OF GROUP
Individuals assigned to a station hunt group may temporarily remove their telephones from the group by
pressing the In/Out of Group button providing that there is someone still in the group.There is a system wide
option to allow all members to log out of a station group. Stations out of a group will not receive calls to that
group but will continue to receive calls to their individual extension numbers.When desired, the user may put
him/herself back into the group by pressing the button again. Users who do not have this button may dial
the access code and the group desired. A station user is allowed to be in several groups, providing a key and
the extender of that group are assigned for each group on the user’s phone.
4.17
INCOMING CALL DISTRIBUTION
Incoming calls can be assigned to ring a distributed station hunt group.This allows all members of the group
to share the call load.
INCOMING/OUTGOING SERVICE
Outside lines are available for incoming or outgoing service. Programming allows any outside line to be used
for incoming calls only, outgoing calls only or both way service.
INDIVIDUAL LINE CONTROL
Each station in the system can be individually programmed to allow or deny dialing out as well as allow or
deny answering for each outside line.
IP KEYSETS
The OfficeServ 500 system allows the use of Samsung proprietary keysets that use Internet Protocols (IP) for
voice and data transport. They may be local to the system or installed in a remote location via a LAN/WAN.
The M version of the system can support up to 120 IP stations and the L version can support up to 240 IP stations. For more information on how to setup the IP keysets please refer to the VOIP Special Applications
Section of the Technical Manual.
ISDN SERVICE
Primary Rate Interface (PRI)
The OfficeServ 500 supports Primary Rate Interface ISDN. PRI allows simultaneous data calls, calling party and
calling line identification, high speed call setup and disconnect are among the benefits of ISDN calling. The
23+D configuration of ISDN allows call information to be delivered via the data channel (the “D” of 23B+D)
thus leaving the bearer channels (the “B” of 23B+D) available for single use or combined use to provide a
wider bandwidth for data and video.The OfficeServ 500 supports the most popular protocol standards in the
U.S.
PRI Protocols supported:
National ISDN-2 (NI2)
AT&T No. 5 ESS
DMS 100/250
Basic Rate Interface (BRI)
The OfficeServ 500 BRI card supports trunk or station level Basic Rate Interface services (BRI).Trunk or station
BRI use is software programmable. BRI allows simultaneous data calls, called party and calling number identification, high speed call setup and disconnect are among the benefits of ISDN calling. The 2B+D configuration of ISDN allows call information to be delivered via the data channel (the “D” of 2B+D) thus leaving the
bearer channels (the “B” of 2B+D) available for single use or combined use to provide a wider bandwidth for
data and video.
LAN INTERFACE
The OfficeServ 500 MCP2 card provides a 10/100 base T Ethernet interface for connection to a data network.
This interface allows a high speed connection for PC programming across an IP network. This interface also
allows the system software to be uploaded to the SmartMedia card via the OfficeServ™ Manager program.
4.18
LEAST COST ROUTING
Least Cost Routing (LCR) is the ability to automatically select the most cost effective central office route for
the outside number dialed by any station. The OfficeServ 500 LCR program includes the following features:
•
•
•
•
•
•
•
Option to use or not user LCR or a tenant basis
Programmable LCR access code
Digit analysis table of 2000 entries each with ten digits
Routing by time of day and day of week (4 time bands per day)
Modify digits table of 200 entries
Flexible trunk group advance timer
Option to use or not use trunk group advance warning tones
LIVE SYSTEM PROGRAMMING
The system can be programmed from any display keyset or personal computer without interrupting normal
system operation. There are 3 levels of programming: technician, customer and station. The technician level
has access to all programs and can allow the customer access to system programs as needed.Technician and
customer access are controlled by different security passcodes. Programming from a PC requires the
OfficeServ™ Manager (OSM) program.The system can also be programmed remotely via an optional internal
modem card or over the internet via the LAN card.
MEET ME PAGE AND ANSWER
After a user makes a Meet Me Page, the user may remain off-hook to allow the paged party to meet the user
for a private conversation.
MEMORY PROTECTION
In the event that power is lost to the system, all customer data contained in memory is retained by the use
of a “super capacitor” for approximately 5 days. Additionally, the Smart Media card may be used to store the
system database. The OfficeServ™ Manager (OSM) computer program may be used to produce a backup
copy of the customer data.
MESSAGE WAITING INDICATIONS
When calling a station and receiving a busy signal or the no answer condition, the caller can leave an indication that a message is waiting.The message button will flash red at the messaged keyset. A single line phone
connected to a 16MWSLI or 8MWSLI will have a message light otherwise it will receive a distinctive message
waiting dial tone. Five message waiting indications can be left at any station.
MESSAGE WAITING KEY
The Message Waiting (MW) key is used in conjunction with a voicemail card.The MW key is programmed with
an extender matching a station or station group number and is used to access the voice mailbox associated
with the extender.
MICROPHONE ON/OFF PER STATION
The microphone can be disabled at any keyset. When the microphone is disabled, the keyset cannot use the
speakerphone, although on-hook dialing and group listening are still possible.
4.19
MOBILITY SOLUTION
Samsung offers a Single-Line integrated Mobility (SLiM) solution that provides hand-off and roaming capabilities. Each SLiM handset requires one SLI port in the OfficeServ 500 system. See your Authorized Samsung
Dealer for additional information.
MULTIPLE LANGUAGE SUPPORT
The OfficeServ 500 can be programmed to support multiple languages in the display. This is on a per-keyset
option and when set the keyset will have its display information presented in the programmed language.The
languages are defined in MMC 121. The current languages are as follows: English, Spanish, Italian, German,
Portuguese, Norwegian, Danish, Dutch, Swedish, US Spanish, and Canadian French.
MUSIC ON HOLD—FLEXIBLE
The OfficeServ 500 allows its music sources to be used in flexible manner as follows:
Each keyset can have a designated music source for playing as Background Music (BGM) through the keyset
speaker.
Each Station can have a designated music source for playing to callers placed on Exclusive hold at that station.
Each Trunk can have a designated music source for playing to callers placed on hold. This setting is overridden by some of the other settings such as station music on hold, DID MOH and UCD MOH.
Each UCD group can have a designated music source to be played while a caller is in queue.
Each entry in the DID translation table can have a designated music source to be played when a caller to that
DID number is placed on hold.
MUSIC ON HOLD – SOURCES
The OfficeServ 500 provides for up to six different types of Music on Hold source including silence or “NONE”
as listed below:
•
None: No audio is played to the listener
•
Tone: A tone or “beep” is repeated at a programmable interval
•
Chime: A music chime source (Old Folks At Home) located on the MCP2 card is played to the listener.
•
External Source: An external source connected to a MISC card, such as a digital announcer or radio, is
played to the listener.
•
Digital Announcement on AA card: If the system is equipped with an AA card the last port of this card
can be flagged as a MOH source and used to repeatedly play a message recorded on the AA card to the
listener.
•
Voicemail Sound File: If the OfficeServ 500 system has an optional CADENCE/SVMi card installed, up to
100 custom recorded sound files from the Voice Mail card can be used for MOH sources. For more information on creating the sound files see CADENCE/SVMi System Administrator Manual-Recording
Greeting by Number. If you select this option be advised that each VMMOH source requires a dedicated
CADENCE/SVMi port.
4.20
NETWORKING
The OfficeServ 500 system allows up to 99 systems to be networked together with a high level of feature integration. The networked systems may be any combination of OfficeServ 100 and OfficeServ 500 systems running V2.4 or higher software. The physical connection between systems can be an IP network or proprietary
PRI connection using Samsung’s proprietary version of QSIG, called SPNet.
When engineering the network of systems, a discrete numbering plan must be used. The size and complexity of the numbering plan as well as the number of stations and trunks may limit the actual number of nodes
available to the network.
•
Auto Answer Across Network: This setting will allow station to station calls across the network to follow
the auto answer setting of the called keyset.
•
Call Completion, Busy Station (CCBS) also known as Callback or Busy Station Callback. When a station in
one system calls a station in another system across the network link and the destination station is busy
the calling station can set a Callback to the busy station.When the busy station becomes idle the system
will notify the callback originating station by ringing that station and when the originating station
answers, the system will call the destination station. Not available on QSIG over PRI.
•
Call Completion, No Response (CCNR) also known as Callback or No Answer Callback. When a station in
one system calls a station in another system across the network link and the destination station does not
answer the calling station can set a Callback to the called station. When that station indicates the user is
present by becoming busy then idle the system will notify the callback originating station by ringing that
station and when the originating station answers, the system will call the destination station.
•
Call Intrusion (Barge In): Calls across the network link can be barged in on however the barging station
will not be muted.
•
Call Offer/Call Waiting (Camp On): This feature operates in the same manner as in a non networked
switch. When a called station is busy the caller can press a camp on key and appear as a ringing call on
the second call button.The Auto camp on feature will not work on calls across a network link if set to ON
in MMC 110.
•
Call Pick-up Across the Network: This feature allows ringing calls, held calls and recalls to be picked up
by other stations through the network. A station user in a Branch Office can use the Directed Pick-up,
Hold Pick-up or Page/Park Pick-up codes to answers calls from the Main Office.
•
Call Transfer: Calls answered in one network node can be transferred to a station or station group in
another network node.
•
Caller ID: Caller ID in its various forms that are currently available (Analog CID Name and Number, ANI
Number, PRI Name and Number and BRI number) will be transported across the network link with the
original call.
•
Centralized Automated Attendant: The Samsung Automated Attendant (AA) card can transfer callers to
other stations or station groups in another Node. It can be installed in any Node regardless of where the
lines/trunks from the telephone company are connected. Callers to Node A can be answered by the AA
Card in Node B, then transferred to Node C. An incoming caller that dials an invalid extension number to
the AA can be routed after a programmable number of attempts to a predetermined station or station
group anywhere in the network to receive assistance.
•
Centralized Operator/Attendant: A station in any Node may dial “O” and ring a designated Centralized
Operator/Attendant. When programmed, hold/transfer/camp-on/park recalls can be directed to the
Centralized Operator/Attendant in a network arrangement instead of the Local Operator within that
Node. Ring plan assignments will allow recalls to a Centralized Operator/Attendant during the day and
to the Local Operator after hours. There can only be one Centralized Operator/Attendant designated in
the network. Each Node must be set for either Local Operator or Centralized Operator/Attendant, but not
both.
4.21
•
Centralized Voice Mail with Message Waiting Lights: This feature allows one Voice mail system to be
shared by all stations in a multi-node network. This feature is only available with the Samsung SVMi or
SVMi-E integrated voice mail systems. Users in one Node can call forward their calls to the voice mail system in another Node. Messages left in the voice mail system will be indicated by lighting the corresponding voice message button or lamp on any station in any Node of the network. Messages are retrieved
by pressing the VMSG button or calling the voice mail group number. In addition, display keyset user will
receive softkey options to navigate through the voice mail system. Softkeys include: PLAY, SAVE, DELETE,
PAUSE FAST FORWARD, REVIEW, REPLY, FORWARD, CALL and HELP.
•
DID with Pass Through: Incoming DID, DNIS or DDI calls can be routed through one switch across a network link to be processed by the DID table of the destination switch.
•
Direct Station Selection and Busy Lamp Indication Across the Network: A Network Station key (NS) can
appear on extension “2101” in Node A. It is programmed as “NS2205” representing an extension in Node
B. This NS key will light Red when extension 2205 is on the phone. Station 2101 can press this NS key to
call extension 2205 in Node B. With this feature the CEO can see when the VP in New York is on the phone
or may call him with the press of a button. Any keyset can have multiple NS keys. This feature is only supported with QSIG over IP networking.
•
Do Not Disturb (DND): This feature operates in the same manner as in a non networked switch.
•
Forward External: This feature operates in the same manner as a non networked system with the exception that, because calls across a network link are trunk calls, network calls do not follow the ICM FWD EXT
ON/OFF setting in MMC 210. It is therefore suggested that this setting be set to ON in a networked switch
to avoid confusion in operation between networked and non networked calls.
•
Group Overflow Across the Network: Calls to a station group in one Node may overflow after a programmable time to another station group in another Node.
•
Intercom Calling/Discrete Dialing Plan: Station to station and station to group calls can be made across
the network link without having to dial an access code for a call within the network. LCR can also be programmed to route calls across a network link and to access local trunks in another networked system.
•
Message Key Across the Network: This feature allows station users to set a message waiting indication
to another station in another Node in the network. Upon receiving a busy or no-answer condition, press
the MSG key or dial the feature code. This will light the message waiting light at the called station. To
return the message press the MSG key with the flashing red LED.
•
Network Page Key: With one or more of these keys users may make page announcements to page zones
in others Nodes in the Network. The network page (NP) key is different than the Page key in a single
node. For example, It is programmed as NPO24 where 02 = Node 2 and 4 = page zone 4 in Node 2.
•
Network Trunk Ring Destination: This feature allows lines/trunks from the telephone company connected to one Node to be programmed to ring at a destination (station or station group) in another Node.
•
Remote Hold Across the Network: Calls may be placed on hold at stations in another Node. Then page
that Node and announce that there is a call on holding on extension 2xxx. Anybody in this Node may
pick up the call by dialing 12 + 2xxx. This is useful when one Node does not have a dedicated answering
position. The caller is on Hold listening to music rather then listening to ringback tone.
•
Transfer Recall: Calls transferred across a network link will recall to the transferring station after the originating system transfer recall timer expires. After recalling, if not answered prior to that systems attendant recall timer expiring, the call will recall to that systems designated operator group. Attendant recalls
will not recall to a ‘Centralized Attendant”.
•
Transfer Retrieve: Calls on Transfer Hold during a screened transfer can be retrieved by pressing the call
button for that call.
4.22
•
Voice Mail Transfer Key: Users may transfer a caller directly to a co-workers voice mail box with out ringing their telephone by pressing the VT key and dialing their extension number. The caller will then hear
that co-workers personal greeting regardless of where they are in the network.
OFF PREMISES EXTENSIONS (OPX)
A single line (tip and ring) extension from an 4SLI card may be connected to telephone company-provided
OPX circuits to remote locations. Other SLI cards such as 8SLI and KDb-SLIs do not support off premises
extensions as they do not have over voltage protection.
OPERATOR GROUP
The operator group can contain 32 stations to answer incoming calls. Calls to this group can be set for distributed, sequential or unconditional ringing. Operators can use the In/Out of Group feature to meet flexible
operator requirements. Operator groups are selectable per ring plan.
OVERFLOW
Operator
When calls ringing a operator group go unanswered, they can overflow to another destination after a programmed period of time. The operator group has its own timer. The overflow destination can be a station or
station group.
Station Group
When calls ringing a station group go unanswered, they can overflow to another destination after a programmed period of time. Each station group has its own timer. The overflow destination can be a station or
station group located in that system.
OVERRIDE CODES
This feature allows users to make emergency outside calls from a station that has a forced code such as
Account code or authorization code enabled but without requiring them to enter a forced code. The basis of
this feature is an override code table containing 8 entries of up to 11 digits each. The OfficeServ 500 will
examine digits that are dialed from a station to see if they match any entry in the Override Code table. If the
digits match the table, the system will process the call without requiring a forced code.
PAGING
System software allows the use of five internal and four external paging zones. Stations can page any individual zone, all external zones or all external zones plus internal zone zero simultaneously. Using system programming, each station may be allowed or denied the abilities to make and/or receive page announcements
to any zone or combination of zones.
PARK ORBITS
The system has 10 park orbits (0–9). These orbits can be used to park calls prior to paging and allows the call
to be retrieved by dialing a park code plus the orbit number. Calls parked in this manner can also be retrieved
by dialing the park pickup code (10) plus the station or trunk number. This feature is in addition to Call Park
and Page.
PRIME LINE SELECTION
Any station can be programmed to select a specific line, trunk group, telephone number, station or station
group when the handset is lifted or the speaker key is pressed (same as Hot Line feature).
4.23
PRIORITY CALL QUEUING
This feature places calls to an UCD or NORMAL station queue ahead of other calls based on priority level (19).The system reads the DID number, Caller ID number or trunk ID number, compares it to a preprogrammed
table, then assigns it the corresponding priority that places it in the appropriate position in the group queue.
PRIVATE LINES
For private line use, stations can be prevented from dialing and/or answering any line.
PROGRAMMABLE LINE PRIVACY
Each outside line can be programmed to ignore the automatic line privacy. This allows up to four other parties to join your conversation by pressing the line button. This is similar to 1A2 key telephone operation.
PROGRAMMABLE TIMERS
There are over 50 programmable system timers to allow each installation to be customized to best fit the end
user’s application.
RECALLS
Calls put on hold, transferred or camped-on to any station will recall to the originating station if not answered
within a programmable time. A recall that goes unanswered for the duration of the attendant recall timer will
recall to the system operator group. Hold, transfer, camp-on and attendant recalls have individual programmable timers. Calls recalling to buttons with tri-colored LEDs will flash amber.
RECALL TO OPERATOR
This function will allow the call to recall the operator instead of to the transferring station after the transfer
recall time expires.
REDIAL REVIEW
The Redial Review feature allows a review of the last number before dialing or allows access to the Call Log
Blocks if assigned.These Call Log Blocks record the last ten (10) numbers dialed.When the LNR key is pressed
the last number dialed is displayed.The log can then be scrolled using the Volume (Up/Down) keys and a previously dialed number can be selected.
REMOTE PROGRAMMING—PC
Remote programming allows the technician to access the system database from a remote location for the
purpose of making changes to the customer data. There are two connection methods, the dial-up connection using the internal modem card and through the LAN connection on the MCP2 card. OfficeServ Manager
is the proprietary programming application used to access and manipulate the database.
RING MODES
Time Based Routing - Plans
Each C.O. line can be programmed to ring at any station or station group. Each line can be assigned a ring
destination based on six (6) different ring plans based on time of day and the day of the week. The system
operator (intercom dial “0”) can also be a different station group for each ring mode.
4.24
Automatic / Manual
Ring destinations will automatically change based on time of day and day of week.
At any time the system can be manually forced into a specific ring plan. It will remain in this ring plan until
manually taken out.
Holiday Schedule
The system has a table of 20 dates that are used to define holidays. On a date designed as a holiday the system will remain in a ring plan for that calendar day providing the system was already in that ring plan. This
feature will override the ring plan time table.
Temporary Override
At any time the system can be forced into a specific ring plan for a temporary period of time until the next
scheduled ring plan automatically takes effect.
RING OVER PAGE
Any outside line can be programmed to ring over a customer-provided paging system. Outside lines, door
phones and station groups may ring over page in the day or night mode.
SECRETARY POOLING
Each keyset may be defined as an executive (BOSS in programming) or a secretary (SECY in programming) in
system programming. Each executive can have up to four secretaries and each secretary can have up to four
executives.These arrangements are known as executive/secretary pools.There can be multiple pools in a system. When an executive is in DND, all calls to the executive ring the first secretary assigned to that executive;
if that secretary is busy, the call will hunt to the next available secretary assigned to that executive. If the secretary must communicate with the executive while he/she is in DND, pressing the corresponding executive
button on the secretary’s keyset results in an Auto Answer intercom call being made to the executive (providing the executive is free). There is also a system wide option to allow the stations to ring rather than auto
announce the executive secretary calls. A station can only be the executive of one secretary pool. In addition,
a station cannot be in more than one pool.
SINGLE LINE CONNECTIONS
Single line ports allow connection of a variety of single line telephones plus facsimile machines, answering
machines, loud bells, computer modems, cordless phones and credit card machines. When connecting customer-provided equipment to these extensions, compatibility should be checked out before purchase to
ensure correct operation. Central office ring cadence can be selected for SLT stations. This is helpful when
optional devices cannot detect OfficeServ 500 intercom ring cadence.
SPEED DIAL NUMBERS
The system maintains a library of speed dial numbers that can be allocated to either a shared system wide
list or to an individual user list. The M version software has a library of 2000 numbers and the L version software has 2500 numbers.
Both M and L version software can be programmed to have either 500 or 950 numbers in the system list.
The remaining numbers in the library can be assigned in blocks of 10 each to individual stations for their personal use. A maximum of 5 blocks (50 numbers) can be assigned to a station.
4.25
SPEED DIAL BY DIRECTORY
The OfficeServ 500 system provides the user with the ability to look up a speed dial number and place the
call. There are three speed dial selections: personal, system and station. This feature requires a display keyset.
STATION HUNT GROUPS
System programming allows up to 40 station hunt groups on an OfficeServ 500-M system and 80 station
hunt groups on an OfficeServ 500-L system. One of three ring patterns—sequential, distributed and unconditional—is available for each group. Each unconditional group may contain a maximum of 32 stations and
each sequential and distributed group may contain a maximum of 48 stations. A station may be assigned to
more than one group. Each station group has its own recall timer for calls transferred to that group. There is
a Next Hunt timer for each group to provide circular hunting within the group.
STATION MESSAGE DETAIL RECORDING (SMDR)
The system provides records of calls made, received and transferred. Connecting a customer-provided printer or call accounting system will allow collection of these records. Each call record provides the following
details: station number, outside line number, start date, start time, duration of call, digits dialed (maximum 18)
and an account code if entered. The system may print a header followed by 50 call records per page or send
continuous records with no header for use with a call accounting machine. See the sample printouts.
The SMDR output can be provided through one of the serial ports on the LAN port of the system. The SMDR
format contains many options that allow it to be customized for a company’s individual needs. Options to
print include incoming calls, outgoing calls, in and out of group status, change in DND status, authorization
codes, and caller ID on incoming calls. When Caller ID is enabled a wide carriage printer is required.
STATION PAIR
This feature allows station to be assigned as a “pair”. That is to say a primary and secondary. Calling the primary station will make both stations ring. Selected features such as Message Notification, DND, Callback, and
Class of Service act as one station. This is convenient when an individual has two offices or an office extension and a cordless extension. NOTE: Not all system features are applicable to station pairs. Features designed
for a single user may conflict with paired stations.
SYSTEM ALARMS
A DISA alarm will warn the customer if the DISA security system has been triggered by too many incorrect
password attempts. The alarm can ring any station or group of stations and show an appropriate display at
the assigned stations.
SYSTEM MAINTENANCE ALARMS
The OfficeServ 500 continuously performs internal system diagnostics. When either a major or minor fault is
detected the system can ring stations with an ALARM KEY assigned. The keyset display shows information
that includes the description, location and date and time stamp for each alarm.
A log of 100 alarms are stored in a buffer and can be reviewed at a display keyset or sent to a printer.
SYSTEM DIRECTORY
Each station, station group and outside line can have an 11 character directory name. This name will appear
on keyset displays to provide additional information about lines and stations.
4.26
TENANT SERVICE (2)
The OfficeServ 500 supports two forms of tenant service as detailed below.
•
System Splitting: In the first form there are several programs that allow the OfficeServ 500 to be installed
in tenant applications. These features allow a technician to split the system in two with each tenant having individual control over operator groups, page zones, speed dial numbers, night service (manual or
automatic), DISA and customer level programming. Each tenant is totally separate in the system and no
intercom calling between tenants is permitted.
•
Port Splitting: In this form of tenant services system programming is used to allow or deny access for
making and receiving calls on a per station basis. These settings can be applied to Trunks, trunk groups,
stations and station groups. This allows common items on the system such as the operator group and
LCR to be used by everyone on the system while ensuring that each company can only access their own
lines and incoming calls.
TOLL RESTRICTION
There are 500 allow and 500 deny entries of 11 digits each. Each of these entries can apply to dialing classes
B, C, D , E, F and G. Expensive 976, 1-900, 411 and operator-assisted calls, as well as specific area and office
codes, can be allowed or denied on a per-class basis. Class A stations have no dialing restrictions and Class H
stations cannot make outside calls.
Any outside line may be programmed to follow station toll restriction or follow the toll restriction class
assigned to it. Each station and trunk can have a different dialing class for each ring plan.
Special Code Table
A Special Code Table of ten entries (four digits each) allows use of telephone company features such as CID
blocking (*67) or call waiting disable (*70) without interference to toll restriction or LCR. The Special Code
table allows use of these custom calling features on a per call basis.
TOLL RESTRICTION OVERRIDE
Program options allow system speed dial numbers to follow or bypass a station’s toll restriction class. In addition, users may make calls from a toll restricted station by using the walking class of service or authorization
code feature.
TONE OR PULSE DIALING
Outside lines can be programmed for either tone or pulse dialing to meet local telephone company requirements.
TRAFFIC REPORTING
The OfficeServ 500 system can store peg counts for various types of calls. These peg counts can be printed
on-demand, daily, hourly, or up to three separate programmable shifts. The report includes statistics for each
trunk, trunk group, station, station groups and page announcements. For more details and explanations see
sections 4.9 and 4.10 of this document.
TRANSFER
System operation permits station users to transfer calls to other stations in the system. Transfers can be
screened, unscreened or camped-on to a busy station.
4.27
TRUNK GROUPS
Outside lines can be grouped for easy access by dialing a code or pressing a button.There are 30 trunk groups
available.
UNIFORM CALL DISTRIBUTION (UCD)
UCD is a call distribution method by which callers in a queue are routed to the next available agent. While
waiting in a queue a canned or customized announcement can be periodically played to the caller based on
a programmable timer while retaining their place in the queue. Statistical and historical reports are available
to assist supervisors in managing a call center. See Call Center.
UNIVERSAL ANSWER
Station users may dial the Universal Answer code or press the UA key to answer any outside lines programmed to ring the UA device. The UA device can be a station, group of stations, common bell or ring over
page.
VIRTUAL EXTENSIONS
The OfficeServ 500 has a number of virtual extension ports encoded in the system database. They can be
assigned as keyset or single line analog ports. The M version has 62 and the L version has 118. These ports
have all the attributes of an actual station port including call forwarding. These virtual ports can be
exchanged with real station ports using the set relocation feature to provide hot desking.
VOICE MAIL
Inband Signalling
The OfficeServ 500 system uses DTMF tones (inband signalling) to communicate with any compatible voice
mail system. Stations can call forward to a voice mail system. When answered, the system will send DTMF
tones routing the caller directly to the called station user’s mailbox. Keyset users can press one button to
retrieve messages from the voice mail system. A Voice Mail Transfer key permits keyset users to easily transfer a caller directly to an individual voicemail box without navigating through menus.
Note: Although most voice mail systems will work with the OfficeServ 500, the system data has default values set to work with the Starmail Voice Processing System. They may need to be changed if you are using
another system.
Integrated (In-Skin)
The OfficeServ 500 can be equipped with either the SVMi-8E or SVMi-16E proprietary voice mail/auto attendant card from Samsung. These cards are expandable to 8 and 16 ports respectively. Because it is built into
the system it provides such features as one touch call record, answering machine emulation, and voice mail
box administration with interactive keyset displays. See separate SVMi-8E/16E Documentation.
Voice Over Internet Protocol (VoIP)
The OfficeServ 500 system is VoIP enabled and as such supports the following VoIP services:
1)
H.323 Trunking to another H.323 Gateway.
2)
IP Telephone Sets:
a) OfficeServ ITP-5121D Keyset
b) OfficeServ ITP-5112L Keyset
c) OfficeServ ITP-5107S Keyset
4.28
These IP Keysets can be installed in the local office or in a remote office, home office with full feature
operation.
3)
IP Networking: Connect up to 15 systems together over a managed IP network.
The OfficeServ 500 Media Gateway Interface (MGI) cards support up to sixteen voice calls per card over an IP
network connection using the industry standards based H.323 or SIP protocol.The MGI cards fit into any universal OfficeServ 500 card slot. The OfficeServ 500 supports a maximum of five MGI cards per cabinet.
VoIP is transported by the OfficeServ 500 MGI cards by utilizing the ITU standards based or H.323 or SIP protocol.This standard addresses the means of transferring voice, data, and images through IP (Internet Protocol)
networks.
With VoIP certain compression standards have also been adopted to represent each second of voice with an
amount of bandwidth. The OfficeServ 500 MGI3 utilizes G.711, G.729, G.729A or G.723 standards voice compression codec’s while the MGI2 supports G711, and G729A only. This allows for a selectable 64kbps (G711),
8Kbps (G729A) or 6.3Kbps (G723) bandwidth use when preparing voice compression for IP transport.
Compression is used to reduce the digitized voice into a smaller bandwidth that can be carried in smaller
packets. The VoIP gateway determines the compression method for each call setup. There is also a certain
amount of frame/packet overhead in each compression channel. 64K of bandwidth can support 6~7 calls
simultaneously. This can vary depending on efficiency features like Silence Suppression and multiframe
counts. Unlike switched networks, VoIP connections consist of a sequence of numbered data packets. Since
voice conversation is usually considered “real time” these packets need to be delivered in a consistent manner with minimal delay. This can be controlled via a Gatekeeper which tracks and monitors voice packets.
Gatekeepers are part of the H.323 standard but are not required. The OfficeServ 500 MGI cards are
Gatekeeper compliant.
In any Ethernet environment, packet transfers are subject to delays and/or loss. If these delays are greater
than 200ms the voice quality will deteriorate. The Ethernet data traffic and network topology should be a
consideration when using VoIP. Network congestion will affect call quality in any VoIP application.
WALKING CLASS OF SERVICE
This feature allows users to make calls or use features from a station that is restricted. The users may either
use the WCOS feature code or the authorization code feature. Both methods change the class of service to
correspond with the station passcode or authorization code that is dialed. After the call is completed, the station returns to its programmed class of service.
WIRELESS HANDSET—See Mobility Solution
4.29
STATION FEATURES
Add-On Modules
Manual Signalling
Appointment Reminder
Message Waiting Light / Indication
Automatic Hold
Mute Microphone / Handset
Automatic Privacy
Off-Hook Ringing
Background Music
Off-Hook Voice Announce (Executive)
Busy Station Callback
Off-Hook Voice Announce (Standard)
Busy Station Indications (BLF)
One Time Do Not Disturb
Call Coverage Key
One Touch Dialing Keys
Call Forwarding
On-Hook Dialing
Call Forwarding Override
Privacy Release
Call Logs
Programmable Keys
Call Pickup
Programmed Station Messages
Direct Station Selection (DSS)
Protection from Barge-In
Divert to Voicemail
Redial
Do Not Disturb (Override)
Remote Hold
Do Not Disturb (Programmable)
Ring Modes
Door Lock Release
Ringing Preference
Exclusive Hold
Speakerphone
Group Listening
Station Lock
Headset Operation
Terminal Status Indicator
Hearing Aid Compatible
Tri-Colored Lights
Line Queuing with Callback
Volume Settings
Line Skipping
Wall-Mountable Keysets
Loud Ringing Interface
4.2 STATION FEATURES DESCRIPTIONS
ADD-ON MODULES
iDCS 14 BUTTON AOM
The 14B AOM attaches to the right hand side of an iDCS 18D or iDCS 28D keyset and provides 14 buttons with
red LEDs.These buttons can be used for DSS keys, speed dial bins or any key that does not require a dual colored LED. Does not require a separate DLI port. It uses the same DLI port as the keyset is attached to.
64 BUTTON MODULE
The 64-button module adds to the capability of any keyset. Up to four 64-button modules can be added to
each keyset. The 64 programmable red LED buttons with red LED can be used for feature keys, DSS/BLF keys
or one touch speed dial buttons. A maximum of 4 can be installed on a OfficeServ 500 system running
OfficeServ 500-M version software, or a maximum of 32 can be installed on a OfficeServ 500 system running
OfficeServ 500-L version software. Requires one DLI port per 64B module.
†Requires optional hardware and/or software. Ask your dealer for details.
4.30
APPOINTMENT REMINDER
When programmed for a specific time, a keyset will sound a distinctive ring to remind the user of meetings
or appointments. Alarms can be set for “today only” or for every day at the same time. Up to three alarms may
be set at each keyset. Display keysets can program a message to be displayed when the alarm rings. Non-display keyset users must have the system administrator program messages for them.
AUTOMATIC HOLD
Station users can enable or disable automatic hold at their keysets. While a user is engaged on an outside
(C.O.) call, pressing another trunk key, route key or CALL button automatically puts the call on hold when this
feature is enabled. Pressing TRSF, CONFERENCE, PAGE or a DSS key will always automatically place the call on
hold. This type of automatic hold is not a user-selectable option. Intercom calls can be automatically held if
Intercom Auto Hold is set to ON for the entire system.
AUTOMATIC PRIVACY
All conversations on outside lines and intercom calls are automatically private. The privacy feature can be
turned off on a per-line basis.
BACKGROUND MUSIC
Keyset users may choose to hear music through their keyset speakers when optional external sources are
installed. Each user may adjust this level by the use of a volume control program at the selected keyset.
BUSY STATION CALLBACK
When reaching a busy station, callers may request a callback by pressing one button or dialing a code. The
system rings the caller back when that station becomes idle (a system-wide maximum of 100 callbacks are
allowed at one time including busy station and busy trunk).
BUSY STATION INDICATIONS (BLF)
DSS/BLF keys may be assigned to any keyset or add-on module. These buttons will be off when the station is
idle, light red when that station is in use and flash distinctively when that station is in the DND mode.The system can be programmed to allow the DSS keys to be used to pickup calls at other keysets.
CALL COVERAGE KEY
These keys (buttons) provide a convenient way to cover calls ringing at other stations. Keyset users can have
one or multiple call coverage keys programmed for a station. These buttons flash when a new call or recall is
ringing at the programmed station. In addition, a call coverage delay ring time can be programmed to provide an audible ring tone either immediately or delayed from 1 to 250 seconds. Call coverage keys only flash
and ring when the covered station is idle. When the covered station is off hook the call coverage key lights
red to indicate a busy condition.
CALL FORWARDING
Station users can forward internal and outside calls to other destinations immediately (Forward All), when
busy (Forward Busy) or if not answered in a programmable number of seconds (Forward No Answer). These
forward destinations can all be different. Once a destination has been programmed, it can be turned on and
off with a programmable key. Forward All takes priority over Busy and No Answer conditions.
In addition to the three usual methods of forwarding described above, a fourth option called Follow Me is
available. This option allows a station user to set a Forward All condition from his/her station to another station while at the remote station. To display the Follow Me condition, the TRSF/transfer key lights steady red
4.31
at the station that is forwarded. The TRSF/transfer key also lights if Forward All is set and no key is programmed for Forward All. Keyset users can be given an external call forward button to forward their calls to
an external phone number. Each outside line may be programmed to either follow or ignore station call forwarding. A per-station option controls whether internal calls forward to voice mail or not. Single line telephones must have the system administrator program this feature for them.
CALL FORWARD OVERRIDE
When this option is set to yes for a station then intercom calls from that station will override any call forwarding settings of the called station.
CALL LOGS
With the call log feature, a display keyset user can review up to 50 of the last incoming calls from the Caller
ID review list or up to 50 of the last external telephone numbers that were dialed. The numbers can be
viewed, stored and/or dialed using the associated soft keys. LCR must be enabled for dialing and storing numbers from the CID review list. Optional hardware and/or software may be needed for Caller ID.
CALL PICKUP
With directed call pickup, a user can answer calls ringing at any station by dialing a code plus that extension
number. The group pickup feature allows the user to answer any call ringing within a pickup group. Pickup
keys may be customized with extenders to allow pickup from a specific station or pickup group. The
OfficeServ 500 has 99 programmable pickup groups.
DIRECT STATION SELECTION (DSS)
Programmable keys can be assigned as DSS keys and associated with extension numbers. Users press these
keys to call or transfer calls to the assigned stations.
DIVERT TO VOICEMAIL
A keyset user can immediately divert a ringing call to their personal voice mailbox by pressing the key.This
will override any call forward no answer setting.
DO NOT DISTURB (OVERRIDE)
The DND Override feature allows a keyset with a DND Override key (DNDO) and the appropriate class of service to override the DND setting at a called keyset. This will allow a user to go into DND while waiting for an
important call and have that call transferred to them via a screened transfer from a station (for example the
users secretary) with a DNDO key.
DO NOT DISTURB (PROGRAMMABLE)
The Do Not Disturb (DND) feature is used to stop all calls to a station. System programming can allow or deny
use of the DND feature for each station. Parties calling a station in DND will receive reorder tone.When in DND
mode, calls may be forwarded to another destination. See Forward DND option. A keyset without a DND button can activate DND via the feature access code. The ANS/RLS key will flash at 112 ipm (rapidly) when DND
is set. There is a programmable option to allow a C.O. line to override DND at its ring destination if that destination is a single station.
DOOR LOCK RELEASE
Stations programmed to receive calls from a door phone can dial a code to activate a contact closure for control of a customer-provided electronic door lock.
4.32
EXCLUSIVE HOLD
Pressing HOLD twice will hold a call exclusively at a station so no other station can pick up that call. Intercom
calls are automatically placed on exclusive hold. Exclusive hold for trunk calls can be denied in class of service.
GROUP LISTENING
This feature allows users to turn on the speaker while using the handset. It allows a group of people to listen
to the distant party over the speaker without the microphone turned on.
HEADSET OPERATION
Every keyset can be programmed to allow the use of a headset. In the headset mode, the hookswitch is disabled and the ANS/RLS key is used to answer and release calls. Keyset users may turn headset operation
ON/OFF by keyset programming or more easily by pressing the headset ON/OFF key. The headset key lights
steady red when the keyset is in headset mode.
HEARING AID COMPATIBLE
All OfficeServ 500 keysets are hearing aid compatible as required by Part 68 of the FCC requirements.
LINE QUEUING WITH CALLBACK
When the desired outside line is busy, the user can press the CALLBACK key or dial the access code to place
his/her station in a queue.The user will be called back when the line is available (a maximum of 100 callbacks
are allowed system-wide at one time including busy station and busy trunk).
LINE SKIPPING
When the user is talking on an outside line and the automatic hold feature is turned off, he/she may press an
idle line key and skip to that line without causing the previous call to go on hold.
LOUD RINGING INTERFACE
The MISC daughter board provides an audible ring tone output.This can be connected to a paging system or
single loud speaker to provide loud ring tone for a specific station only. The tone is preset and can not be
changed.
MANUAL SIGNALLING
Keysets can signal each other via a programmable key.This allows one station to alert another without establishing a voice conversation. Each press of the key results in a 500 milliseconds of ring tone being set to the
intended station. An individual manual signaling key must be programmed for each station to be signaled.
MESSAGE WAITING LIGHT/INDICATION
When calling a station and receiving a busy signal or the no answer condition, the caller can leave an indication that a message is waiting.The message button will flash red at the messaged keyset. A single line phone
connected to a 16MWSLI or 8MWSLI will have a message light otherwise it will receive a distinctive message
waiting dial tone. Five message waiting indications can be left at any station.
MUTE MICROPHONE/HANDSET
Any keyset user can mute the keyset’s handset transmitter by pressing the MUTE key. In addition, keyset users
can also mute the keyset microphone while the keyset is in speakerphone mode.
4.33
OFF-HOOK RINGING
When a keyset is in use, the system will provide an off-hook ring signal to indicate that another call is waiting. The ring signal is a single ring repeated. The interval is controlled by a system-wide timer. Single line stations will receive a tone burst through the handset receiver instead of a ring.
OFF-HOOK VOICE ANNOUNCE (EXECUTIVE)
A keyset associated with an add-on module may receive an executive off-hook voice announcement while
on another call. The called keyset user may reply handsfree without interrupting the call in progress. Only
keysets with an off-hook voice announce button (OHVA) can off-hook voice announce to keysets with AOMs.
OFF-HOOK VOICE ANNOUNCE (STANDARD)
Keysets may receive a voice announcement while on another call.The calling station must have an OHVA key.
When transferring a call to a busy keyset or while listening to busy signal, the station user can press the OHVA
key to make an OHVA call to the busy keyset. If the called keyset is in the DND mode, it cannot receive OHVA
calls. The L version of software has an user programmable option that will allow the OHVA to be heard
through the speaker rather than in the handset.
ONE TIME DO NOT DISTURB
The Do Not Disturb (One Time) feature is used to stop all calls to a station when the user is on an outside line
and does not want to be disturbed for the duration of the call. Upon completion of the call, DND is canceled
and the station is returned to normal service. This feature requires a programmed button.
ONE TOUCH DIALING KEYS
Frequently used speed numbers can be assigned to one touch dialing keys for fast accurate dialing.
ON-HOOK DIALING
Any keyset user can originate calls without lifting the handset. When the called party answers, the user may
speak into the microphone or lift the handset for more privacy.
PRIVACY RELEASE
This feature will allow another station to join in on your conversation by temporarily releasing privacy on the
C.O. line from your keyset.
Requires a Privacy Release key to be programmed on your keyset. A maximum of three (3) other people can
join in. This uses one of the conference circuits in the system.
PROGRAMMABLE KEYS
Each key can be programmed for more than 25 different uses to personalize each phone. Examples of keys
include individual outside line, individual station, group of lines, group of stations and one touch speed dial
buttons. Using these keys eliminates dialing access codes.
The following feature keys have extenders that make them more specific: SPEED DIAL, SUPERVISOR, PAGE,
DSS, DIRECTED PICKUP, GROUP PICKUP, DOOR PHONE, BOSS, PROGRAMMED MESSAGE, IN AND OUT OF
GROUP, FORWARD and VOICE MAIL TRANSFER. The extender can be a station, a group or another identifying
number.
4.34
PROGRAMMED STATION MESSAGES
Any station may select one of 20 messages to be displayed at a calling party’s keyset to advise others of their
status.Ten messages are factory-programmed but may be reprogrammed. Five can be created by the system
administrator. Each display keyset user may create five additional messages unique to them.
NOTE: The calling party must have a display keyset to view these messages.
PROTECTION FROM BARGE-IN
Each station can be programmed as secure or not secure. Secure stations cannot be barged-in on. A station
that is not secure cannot be barged-in on when talking to a secure station.
REDIAL
There are three types of external redial available to all station users. Each type can redial up to a maximum of
18 digits.
•
AUTO RETRY—When an outside number is dialed and a busy signal is received, the auto retry feature can
be used to reserve the outside line and automatically redial the number for a programmable number of
attempts (available to keyset users only).
•
LAST NUMBER—The most recently dialed number on a C.O. line is saved and may be redialed by pressing the redial key or dialing the LNR access code.
•
MANUAL RETRY with LNR—When you make an outside call and receive a busy signal you can press the
LNR key to redial the same number again.This operation can be manually repeated for a limited number
of attempts as defined by system programming (available to keyset users only).
•
MEMO REDIAL—When you are calling directory assistance you can store the number you are given using
the dial pad and SAVE number feature. There is no need for a pencil and paper (available to keyset users
only).
SAVE NUMBER—Any number dialed on a C.O. line may be saved for redial at a later time.
•
REMOTE HOLD
When you wish to place a call on hold at another station, press TRSF and dial the station number (or press the
appropriate DSS key). Press the HOLD key.This will place the call on system hold on an available CALL button
or Line Key at the remote station.
RING MODES
Each keyset user can select one of three distinct ways to receive intercom calls. The phone can automatically answer on the speakerphone, voice announce through the speaker or receive ringing.When the ring mode
is selected, keyset users can choose one of eight distinct ring tones. Forced Auto Answer is invoked by the
calling station and is controlled by the calling station’s class of service.
RINGING PREFERENCE
Lifting the handset or pressing the speaker button automatically answers a call ringing at the keyset. Using
this method, users are assured of answering the oldest call first. When ringing preference is turned off, the
user must press the flashing button to answer. Users may answer ringing lines in any order by pressing the
flashing button.
4.35
SPEAKERPHONE
The DS, iDCS and ITP keysets have built-in speakerphone. The speakerphone enables calls to be made and
received without the use of the handset. The iDCS 28D, iDCS 18D, DS 5021D, and DS 5014D keysets can have
a Full Duplex Speakerphone Module added. All ITP phones are speaker phones.
STATION LOCK
With a programmable personal station passcode, any keyset or single line station can be locked and
unlocked to control use of each telephone.There are two lock options: 1=LOCKED OUTGOING and 2=LOCKED
ALL CALLS. See the following table for more details.
0
UNLOCKED
1
LOCKED OUTGOING
2
LOCKED ALL CALLS
Make Outside Calls
YES
NO
NO
Receive Outside Calls
YES
YES
NO
Make Intercom Calls
YES
YES
NO
Receive Intercom Calls
YES
YES
NO
TERMINAL STATUS INDICATOR
The iDCS, DS, and ITP keysets are equipped with a terminal status indicator lamp. The terminal status indicator light is positioned on the top right corner of the keyset above the display. The terminal status indicator is
a tri-colored (red, green, and amber) light that provides greater visibility of your keysets status than the individual key LEDs. The terminal status indicator provides the following indications:
– Busy/Off Hook
– Intercom Ring
– Outside Call Ring
– Recall Ring
– Message Waiting
– Do Not Disturb
Steady Red
Flashing Red
Flashing Green
Flashing Amber
Flashing Red
Fast Flash Red at 1 Second Intervals
TRI-COLORED LIGHTS
The iDCS, DS, and ITP keysets are equipped for tri-colored LED indications (green, red and amber). All programmable keys on the iDCS, DS, and ITP keysets have tri-colored LEDs. To avoid confusion, your calls always
light green, other calls show red and recalls light amber.
VOLUME SETTINGS
Each keyset user may separately adjust the volume of the ringer, speaker, handset receiver, background
music, page announcement and off-hook ring tone.
WALL-MOUNTABLE KEYSETS
Each keyset, add on module and 64 button module can be wall mounted by reversing the base wedge.
4.36
DISPLAY FEATURES
Account Code Display
Enhanced Station Programming
Call Duration Timer
Identification of Recalls
Call for Group Identification
Identification of Transfers
Call Processing Information
Message Waiting Caller Number
Caller ID Information
Outside Line Identification
Calling Party Name
Override Identification
Calling Party Number
Programmed Message Display
Conference Information
Soft Keys
Date and Time Display
Stopwatch Timer
Dial by Name
Text Messaging
Dialed Number
UCD Supervisor Displays
4.3 DISPLAY FEATURES DESCRIPTIONS
ACCOUNT CODE DISPLAY
Account codes are conveniently displayed for easy confirmation. If entered incorrectly, users may press the
ACCOUNT key again and reenter the account code.
CALL DURATION TIMER
The system can automatically time outside calls and show the duration in minutes and seconds. Station users
may manually time calls by pressing the TIMER button.
CALL FOR GROUP IDENTIFICATION
When a call is made to a station group, the display shows [CALL FOR GROUP] and the user’s group number.
These calls can be answered with a different greeting than calls to the user’s extension number.
CALL PROCESSING INFORMATION
During everyday call handling, the keyset display will provide information that is helpful and in some cases
invaluable. Displays such as [CALL FROM 203], [TRANSFER TO 202], [701: RINGING], [TRANSFER FM 203], [708
busy], [Camp on to 204], [Recall from 204], [Call for 501], [message from 204] and [FWD ALL to 204] keep users
informed of what is happening and where they are. In some conditions, the user is prompted to take action
and in other cases the user receives directory information.
CALLER ID INFORMATION
Caller ID information is dependent on the use of display keysets. The following list explains the displays that
are used with Caller ID.
Name / Number Display
Each display keyset user can decide if he/she wants to see the Caller ID name or Caller ID number in the display. Regardless of which one is selected to be seen first, the NND key is pressed to view the other piece of
CID information.
4.37
Next Call
In the event that there is a call waiting or a camped-on call at the user’s keyset, the user can press the NEXT
key to display the Caller ID information associated with the next call in queue at the station. Either the CID
name or CID number will show in the display depending on the N/N (MMC 119) selection.
Save CID/ANI Number
At any time during an incoming call that provides CID information, the user may press the SAVE key.This saves
the CID number in the Save Number feature. Pressing the SAVE number redial key will dial the CID number.
The system must be using LCR to dial the saved number.
Store CID/ANI Number
At any time during an incoming call that provides CID information, the user may press the STORE key. This
saves the CID number as a speed dial number in the personal speed dial list. The system must be using LCR
to dial the stored number.
Inquire Park/Hold
When a user is informed that an incoming call is on hold or has been parked, the user may view the Caller ID
or ANI information before he/she retrieves the call.This will influence how the user chooses to handle the call.
CID/ANI Review List
This feature allows display keyset users to review CID information for calls sent to their stations. This list can
be from ten to fifty calls in a first in, first out basis.The list includes calls that were answered and calls that rang
the user’s station but that were not answered. When reviewing this list, the user can press one button to dial
the person back. The system must be using LCR to dial the stored number.
Investigate
This feature allows selected stations with a special class of service to investigate any call in progress. If
CID/ANI information is available for an incoming call, the selected stations can know to whom the OfficeServ
500 user is speaking. On outgoing calls, the selected stations can see who was called. After investigating, the
selected stations may barge-in on the conversation, disconnect the call or hang up.
Abandon Call List
The system has a system-wide abandon call list that stores CID/ANI information for calls that rang but were
not answered. The list is accessed using the operator’s passcode. When reviewing this list, you are provided
options to CLEAR the entry or DIAL the number. You can use the NND key to toggle between the CID name,
CID or ANI number and the date and time the call came in. The system must be using LCR to dial numbers
from the abandon call list. The abandoned call list will store up to 100 unanswered calls.
CALLING PARTY NAME
For intercom calls, display keysets show the calling party’s name before answering.The names must be stored
in the system directory list and can be up to 11 characters long.
CALLING PARTY NUMBER
When an intercom call is received, all display stations show the calling party’s extension number before the
call is answered.
4.38
CONFERENCE INFORMATION
When a conference is set up, each extension and outside line number is displayed at the controlling station
when it is added. When a station is added, its display shows [Conf with xxx] alerting the user that other parties are on the line.
DATE AND TIME DISPLAY
In the idle condition, the current date and time are conveniently displayed. Display keysets can have a 12 or
24 hour clock in either the ORIENTAL or WESTERN display format with information shown in upper case or
lower case letters.
DIAL BY NAME
Each station and speed dial number can have an associated directory name. Any station or speed dial number can be selected by scrolling alphabetically through a directory list. There are three directories:
1.
2.
3.
System wide speed dial list
Personal speed dial list
Station directory list
This online “phone book” allows display keyset users to look up and dial any speed dial number or station in
seconds.
DIALED NUMBER
When an outside call is made, digits are displayed as the user dials them. If the display indicates an incorrect
number was dialed, the user can quickly hang up before billing begins.
ENHANCED STATION PROGRAMMING
Personal programming options are easier to select and confirm with the help of the display.
IDENTIFICATION OF RECALLS
Hold recalls and transfer recalls are identified differently than other ringing calls. Hold recalls indicate the
recalling line or station number and the associated name.Transfer recalls indicate the recalling line or station
and where it is coming from.
IDENTIFICATION OF TRANSFERS
The display will identify who transferred a call to the user.
MESSAGE WAITING CALLER NUMBER
When the message indication is on, pressing the MESSAGE button displays the station number(s) of the person(s) who have messages for the user. Display keyset users can scroll up and down to view message indications.
OUTSIDE LINE IDENTIFICATION
Each line can be identified with an 11 character name. Incoming calls display this name before the call is
answered. This feature is helpful when individual lines must be answered with different greetings.
4.39
OVERRIDE IDENTIFICATION
If another station barges-in on a user’s conversation, the display will alert the user with a [Barge from 2xx] display if the system is set for barge-in with tone.
PROGRAMMED MESSAGE DISPLAY
Preprogrammed station messages set by other stations are displayed at the calling station’s keyset.
SOFT KEYS
Below the display, there are three soft keys and a SCROLL button.These keys allow the user to access features
in his/her class of service without requiring the keyset to have designated feature keys.
STOPWATCH TIMER
Display keyset users find this feature very convenient to time meetings, calls and other functions. Users simply press once to start the timer and press again to stop the timer.
TEXT MESSAGING
This feature allows two display keyset users to respond to each other with preprogrammed messages. After
receiving an Off Hook Voice Announcement or Station Camp-On, you may respond with a text message while
continuing to talk and listen to your outside party. The other station can view this message and take the
appropriate action or respond back with another text message.
Up to 100 display station users can program their own individual ten (10) text messages that can be sent to
another display keyset. Only the display keysets that are allowed in the system programming (MMC 611) will
receive the (TMSG) text message softkey in the display and can use this feature.
UCD SUPERVISOR DISPLAYS
When a UCD supervisor key is pressed, supervisors can view information about the UCD groups calls or
agents.
Call Screen
This allows the supervisor to view how many calls are in queue, the longest wait time, how many calls have
been received today, what the average time in queue is and how many calls were abandoned.
Agent Screen
This allows the supervisor to monitor how many agents are logged in, check each agents status (IN GROUP,
OUT OF GROUP, or DND), view each agents total number of calls, average call length or average ring time.
Note: Accessing this screen will also allow a Supervisor to change the status of each agent (IN GROUP, OUT
OF GROUP, or DND).
4.40
SAMPLE DISPLAYS
Display model keysets have a large, easy-to-read, 32 character liquid crystal display. Helpful call processing information is provided so everyday call handling is quick and easy. Here are just some of the displays you may see.
Camp on to 203
Wait for answer
209:Tim Kelly
FRI 23 Sep 02:54
Idle display shows extension, name, day, date and
time.
This station is camped-on to extension 203 and is
waiting for 203 to answer.
Call for 501
202 Mr. Smith
This station in the sales department is receiving a
group call from Mr. Smith.
Call for 501
706 Local #6
This display tells you this is a new incoming call to the
sales department.
OHVA from 203
REJECT
203: Busy
CBK MSG CAMP ®
This station is calling station 203 which is currently
busy.
This station is receiving an off-hook voice
announcement from station 203.
CONF:202 702
CONF®
Conf with 203
John
This station is on a conference call with John,
extension 203. Assume other parties will hear your
conversation.
This station is on a conference call with extension 202
and trunk 702 and has the option to add two more
parties.
Call from 201
Operator
Transfer to 203
John
This station is transferring a call to John at
extension 203.
This station is receiving a call from extension 201.
DO NOT DISTURB
ON
OFF
703 Local 3
CONF PAGE MUTE ®
This station is setting the Do Not Disturb feature.
This station is speaking on trunk 703.
4.41
SAMPLE CALLER ID DISPLAYS
05/25,09:41,702
CLEAR NND DIAL
13054264100
702:RINGING
This display shows an incoming call from 1-305426-4100 on Line 702 ringing directly at your
station.
This display shows the information on the
abandoned call list.This call came in on May 25
at 9:41 A.M. on line 702.The user can CLEAR the
entry, DIAL the caller back or examine further
NND information.
13054264100
TRANSFER FM 201
SAMSUNG TELECOM
CLEAR NND DIALà
This display shows a call from 1-305-426-4100
that has been transferred to you from station
201.
This display shows an entry in a station review
list showing the three initial options.The arrow
indicates other options available to you by
pressing the SCROLL key.
SAMSUNG TELECOM
BARGE NND DROP
13054264100
NEXT NND ANS
This display is seen while examining calls in
queue at your keyset.
This display shows an investigation of a station
that is talking to Samsung Telecom. Investigator
can BARGE-in to the conversation, DROP the call
from the system or examine further NND
information.
TALKING TO:203
BARGE
DROP
SAMSUNG TELECOM
CALL FOR:500
This display can be seen when investigating an
intercom call.The investigator can BARGE-in or
DROP the connection.
This display shows an incoming call from
Samsung Telecom ringing at group 500.
SAMSUNG TELECOM
ANS NND IGNORE
This display is seen while using the INQUIRE
feature. It shows the three options available
while you are checking on a held or parked call.
4.42
SAMPLE UCD DISPLAYS
06 available
04 logged in
005 calls in
queue now
There are five calls currently waiting to be
answered by the UCD group.
There are six members in the group. Four of the
members are currently logged in.
201: answered
065 calls today
longest wait
time is 02:24
The longest call on hold (waiting to be
answered) was for two minutes, 24 seconds.This
data applies to all calls since the supervisor data
was last cleared. It does not necessarily
represent calls currently in queue.
The agent at station 201 has answered 65 calls
today.
201: average
call time 04:43
124 calls
received today
The average call length for station 201 is four
minutes and 43 seconds.
The UCD group has received 124 calls today.
202: Sondra
STATUS: OUT
average time in
queue is 03:51
Station 202 is currently out of the group. (The
display can also show IN GROUP and DND.)
The average time on hold (waiting to be
answered) is three minutes and 51 seconds.
4.43
4.44
] Mar/21/1999 13:49
Authorization Code
4 Digits
Date Call Made
or Received
Month:Day
C.O. Line No.
2–4 Digits
Time Call Made
or Received
Hrs:Mins:Secs
Call Duration
Hrs:Mins:Secs
or Call Cost
Call Type Flag
2 Characters
4.4 SAMPLE SMDR PRINTOUT
(WITHOUT CALLER ID)
Tenant
1 Digit
Extension
2–4 Digits
IA
0
I
DI
DO
FO
TT
OT
IT
FI
DE
T
DISA call with error
Transferred call that
was terminated
Incoming transfer
Incoming call forwarded to
an external number
Outgoing transfer - Outgoing call
made and transferred
Caller received a transferred
call and transferred it again
Call Type Flag Definitions
Account Code
1–12 Digits
Outgoing Call
Incoming Call
DISA call in
DISA call out
Outgoing record of
forwarded call
Incoming Ring
Time Before Being
Answered
Telephone No. Dialed
1–18 Digits
===============================================================================
T EXT AUTH TRK MM/DD STT.TIME DURATION FG DIALED DIGIT
ACCOUNT CODE
===============================================================================
725 03/21 13:51:17 00:00:08 IA
1 3951
725 03/21 13:51:25 00:00:14 IT
1 3951
744 03/21 13:51:29 00:00:14 IA
1 217
725 03/21 13:51:39 00:00:06 T
1 235
726 03/21 13:51:25 $ 10.75 O 3056401067
*1234567890#
1 219
744 03/21 13:51:43 00:00:40 I
1 217
725 03/21 13:53:40 00:00:07 O 18007864782
1 278
726 03/21 13:54:45 00:00:07 IA
1 3951
GROUP OUT
03/21 13:55:03
1 219
726 03/21 13:54:52 00:00:30 IT
1 3951
726 03/21 13:55:22 00:00:16 TT
1 217
DND ON
03/21 13:55:30
1 235
726 03/21 13:55:38 00:00:33 TT
1 218
DND OFF
03/21 13:57:50
1 235
1 279 6398 727 03/21 13:57:32 $ 13.25 O 3056401066
GROUP IN
03/21 14:00:45
1 219
726 03/21 13:56:11 00:05:38 T
1 219
725 03/21 13:54:40 00:07:06 O 3055922900217
1 296
717 03/21 14:03:57 00:00:15 O 19544530000
*1234567890#
1 219
SMDR REPORT FOR [STA Miami
4.45
] Mar/21/99 13:49
4.5 SAMPLE SMDR PRINTOUT
(WITH CALLER ID/ANI NUMBER)
Call Duration
Hrs:Mins:Secs
or
Call Cost
Time Call Made
Call Type Flag
or Received
2 Characters
Hrs:Mins:Secs
Date Call Made
or Received
Month:Day
C.O. Line No.
2–4 Digits
Authorization
Code
4 Digits
Extension
2–4 Digits
Tenant
1 Digit
Telephone No. Dialed
1–18 Digits
A
IA
0
I
DI
DO
FO
Caller ID Name
1–15 Characters
TT
OT
IT
FI
DE
T
DISA call with error
Transferred call that was
terminated
Incoming transfer
Incoming call forwarded to
an external number
Outgoing transfer - Outgoing call
made and transferred
Caller received a transferred
call and transferred it again
Call Type Flag Definitions
Caller ID Number
1–15 Digits
Outgoing Call
Incoming Call
DISA call in
DISA call out
Outgoing record of
forwarded call
Abandoned call
Incoming Ring
Time Before Being
Answered
Account Code
1-12 Digits
==================================================================================================================
CID/ANI NAME
ACCOUNT CODE CID/ANI NUMBER
T EXT AUTH TRK MM/DD STT.TIME DURATION FG DIALED DIGIT
==================================================================================================================
725 03/21 13:51:17 00:00:08 IA
1 3951
SAMSUNG TELECOM
13055922900
725 03/21 13:51:25 00:00:14 IT
1 3951
1 217
744 03/21 13:51:29 00:00:14 IA
SAMSUNG TELECOM
13055922900
725 03/21 13:51:39 00:00:06 T
1 235
*1234567890#
726 03/21 13:51:25 $ 10.75 O 3056401067
1 219
13055559748
PIZZA DELIVERY
744 03/21 13:51:43 00:00:40 I
1 217
725 03/21 13:53:40 00:00:07 O 18007864782
1 278
1 3951
726 03/21 13:54:45 00:00:07 IA
GROUP OUT
03/21 13:55:03
1 219
SAMSUNG TELECOM
13055922900
726 03/21 13:54:52 00:00:30 IT
1 3951
13055922900
SAMSUNG TELECOM
1 217
726 03/21 13:55:22 00:00:16 TT
DND ON
03/21 13:55:30
1 235
PIZZA DELIVERY
13055556420
1 218
726 03/21 13:55:38 00:00:33 TT
DND OFF
03/21 13:57:50
1 235
1 279 6398 701 03/21 13:57:32 $ 13.25 O 3056401066
GROUP IN
1 219
03/21 14:00:45
SAMSUNG TELECOM
13055922900
726 03/21 13:56:11 00:05:38 T
1 219
1 296
725 03/21 13:54:40 00:07:06 O 3055922900217
SMDR REPORT FOR [STA Miami
4.6 SAMPLE OF UCD EMBEDDED REPORT
============================================================
UCD GROUP 529 : SALES
FROM: SUN 02 Feb 00:00
TO : SUN 02 Feb 02:54
CALL STATISTICS
===============
AVERAGE RING TIME(TIME TO ANSWER)......00:40
NUMBER OF TIMES ALL AGENTS BUSY........00002
AVERAGE TIME IN QUEUE..................00:51
TOTAL CALLS RECEIVED...................00011
LONGEST QUEUE TIME(TODAY)..............02:14
TOTAL CALLS ABANDONED..................00004
AGENT STATISTICS
================
MEMBER AGENT NAME
CALLS
AVERAGE
RING
ANSWERED
CALL TIME
TIME
-----------------------------------------------------------01
210
JOHN
0002
01:55
00:05
02
211
SAM
0001
02:18
00:06
03
208
MIKE
0003
01:22
00:04
04
207
PETER
0001
03:16
00:05
============================================================
UCD GROUP 515 : SUPPORT
FROM: MON 03 Jan 08:30
TO : SUN 02 Jan 02:54
CALL STATISTICS
===============
AVERAGE RING TIME(TIME TO ANSWER)......00:07
NUMBER OF TIMES ALL AGENTS BUSY........00005
AVERAGE TIME IN QUEUE..................01:06
TOTAL CALLS RECEIVED...................00023
LONGEST QUEUE TIME(TODAY)..............01:02
TOTAL CALLS ABANDONED..................00001
AGENT STATISTICS
================
MEMBER AGENT NAME
CALLS
AVERAGE
RING
ANSWERED
CALL TIME
TIME
----------------------------------------------------------01
223
FRED
0012
02:33
00:08
02
213
JANE
0010
01:04
00:04
4.46
4.7 UCD CALL STATISTICS
CALLS IN QUEUE NOW
How many calls are currently in queue. This statistic is a real time statistic and so will not print on a report.
ABANDONED CALLS
This shows the number of callers that reached the UCD group, but hung up before being answered. A high number probably means that there are not enough agents available and the wait time is too long.
AVERAGE RING TIME
This is calculated from the time an agent begins to ring until the time an agent answers the call, this does not
include ringing at an agent station that does not answer or is logged out because of the ring next option.
NUMBER OF TIMES ALL AGENTS BUSY
This is the number of times that a call is placed to an UCD group and all agents are busy or out of group.This check
is made when the call is first placed to the group.
Example: If there are 5 members in a group, 3 are Out of Group one is busy and one is idle, and a call is placed to
the group, because there is an idle station the all agents busy counter is not incremented.
If the idle station rings, does not answer and is logged out, although the condition of the group is now all agents
busy, the check has been made and the agent busy statistic does not increment.
Also if a call comes into a group with all agents busy and then one becomes idle, the busy counter will increment
because the check has been made.
AVERAGE TIME IN QUEUE
This is calculated as an average of all the calls that were in queue.
Note that this is ONLY an average of the calls that were in queue. The caller must have overflowed to the UCD
recording to be considered in queue.
A call is considered in queue until it is answered or until it goes to the final destination.
TOTAL CALLS RECEIVED
The total number of times that calls were sent to a group. This includes calls that were answered by the group,
calls that went to a group with all agents busy or out of group, calls that are abandoned and calls that go to UCD
final destination. This includes intercom calls to the UCD group.
If this number is less than the total calls received by all the agents it is possible that calls were transferred from
one agent to another.
If this number is more than the total calls received by all the agents it is possible that calls were unanswered by
an agent and went to final destination or callers hung up while in queue.
4.47
This statistic includes:
a)
Calls answered by agent.
b) Calls that are not answered by an agent and go to final destination.
c)
Calls that are sent to the UCD group but callers hang up before being answered.
LONGEST QUEUE TIME TODAY
This shows the longest call in queue today. The queue time is calculated as follows:
a)
Queue time begins when a caller starts to hear the first UCD message.
b) Queue time ends when a caller is either
•
Answered by an agent
•
System gets disconnected from C.O. or
•
Caller is transferred to final destination
LONGEST QUEUE TIME NOW
This shows the longest call currently in queue. The queue time is calculated as follows:
a)
Queue time begins when a caller starts to hear the first UCD message.
b) Queue time ends when a caller is either
•
Answered by an agent
•
System gets disconnected from C.O. or
•
Caller is transferred to final destination
4.48
4.8 UCD AGENT STATISTICS
LOGGED IN
The number of stations programmed in the UCD group and the number of stations that are currently logged in.
This statistic is a real time statistic and so will not print on a report.
STATUS
This screen shows the agents name, extension number and status. The status can be In Group, Out of group or in
DND. This statistic is a real time statistic and so will not print on a report.
CALLS ANSWERED
The total number of calls answered by the agent. This does not include ring no answer to an agent station. If this
total number is less than the calls received by the group it is possible that calls were unanswered by an agent and
went to final destination or that callers hung up while in queue. If this total number is more than the calls received
by the group it is possible that calls were transferred from one agent to another.
AVERAGE CALL TIME
This is an average of all the call durations for the agent.
AVERAGE RING TIME
This is an average of all the ring times for the agent. Ring times are previously explained.
4.49
4.9 SAMPLE TRAFFIC REPORT
TRAFFIC REPORT FOR [ STA Miami
] Mar/21/1999 13:35
**************************** SYSTEM STATISTICS ******************************
BEGINNING:
Mar/15/1999
00:42
ENDING:
ACTIVITY
INCOMING TRUNK CALLS
INCOMING TRUNK CALLS
OUTGOING TRUNK CALLS
A SELECTED TRUNK WAS
Mar/21/1999 13:32
SYSTEM TOTAL
- ANSWERED..................
- NOT ANSWERED..............
............................
BUSY........................
3041
26
2168
44
INTERCOM CALLS - COMPLETED.......................
INTERCOM CALLS - NOT ANSWERED....................
7178
1540
TRUNK RECALLS TO STATION.........................
TRUNK RECALLS TO OPERATOR GROUP..................
145
32
INTERNAL PAGE USED...............................
EXTERNAL PAGE USED...............................
ALL PAGE USED....................................
35
79
231
**************************** TRUNK GROUPS ***********************************
GROUP
OUTGOING BUSY
9
1245
18
800
521
3
801
20
3
802
0
0
*************************** INDIVIDUAL TRUNKS *******************************
TRUNK
701
702
703
TRUNK-NAME
LOCAL 1
LOCAL 2
LOCAL 3
ATTA
0
0
0
ANSD
737
541
290
NOT-ANSD
0
4
1
OUTGOING
19
26
37
BUSY
12
11
21
************************* STATION HUNT GROUPS ********************************
GROUP
500
501
502
503
504
<———————— OUTSIDE CALL ————————>
ANSD
NOT-ANSD
439
19
261
37
40
2
87
5
19
1
<-INTERCOM->
ANSD
61
38
77
162
44
*********************** INDIVIDUAL STATIONS *********************************
<—————— OUTSIDE CALL ——————————————————————————><-INTERCOM——>
EXT STATION-NAME ATTA ANSD NOT-ANSD DIALED ICM–TRSF TRK-TRK PICKUP ANSD DIALED
201 Operator
9 360
11
15
341
0
0
39
72
202 Barbara
12
60
2
80
20
0
12
49
66
203 Ivania
4
25
1
36
3
0
18
86
29
4.50
4.10 TRAFFIC REPORT OVERVIEW
A***************************** SYSTEM STATISTICS ****************************
1 BEGINNING:
2
04/01/99
08:00
ENDING:
ACTIVITY
04/01/99 17:30
SYSTEM TOTAL
3
4
5
6
INCOMING TRUNK CALLS
INCOMING TRUNK CALLS
OUTGOING TRUNK CALLS
A SELECTED TRUNK WAS
7
8
INTERCOM CALLS - COMPLETED.......................0000
INTERCOM CALLS - NOT ANSWERED....................0000
9
10
TRUNK RECALLS TO STATION.........................0000
TRUNK RECALLS TO OPERATOR GROUP..................0000
11
12
13
INTERNAL PAGE USED...............................0000
EXTERNAL PAGE USED...............................0000
ALL PAGE USED....................................0000
- ANSWERED..................0000
- NOT ANSWERED..............0000
............................0000
BUSY........................0000
1. BEGINNING & ENDING
This identifies when the statistics were collected. It includes dates and time.
2. ACTIVITY: Overall summary of traffic in the system for activities 3 to 13.
3. INCOMING TRUNK CALLS-ANSWERED: These are any incoming trunk calls to the system. These calls are
pegged when answered by any device and/or station in the system whether it is a new call or a recall.
4. INCOMING TRUNK CALLS-NOT ANSWERED: These are any incoming trunk calls that were not answered by
any station or device in the systems. These are the same calls that would be flagged as abandoned in SMDR.
5. OUTGOING TRUNK CALLS: These are all outgoing trunk calls that were originated by any station or through
the DISA feature. Outgoing trunk calls are valid calls as defined by the SMDR START TIME in MMC 501.
6. A SELECTED TRUNK WAS BUSY: Pegged every time a trunk or trunk group was busy regardless of the manner in which it was selected (e.g., DTS key, LCR,“9”, 7XX, TRK GROUP SELECT, SPD, External call forward, DISA).
7. INTERCOM CALLS COMPLETED: These are all intercom calls that were completed to any station, station
group or device.
8. INTERCOM CALLS NOT COMPLETED: These are all intercom calls that were not answered and resulted in the
calling party hanging up. A call to a station group that overflows to another station is considered not
answered whether the overflow destination did or did not answer.
9. TRUNK RECALLS TO STATION: These are trunk calls that were placed on any kind of hold and recalled a station.These are also trunk calls that were transferred and were not answered and recalled the transferring station. This includes members of the operator group that put calls on hold and then recall the operators station.
4.51
10. TRUNK RECALLS TO OPERATOR GROUP: These are any trunk calls that recalled to the operator group.
11. INTERNAL PAGE USED: Peg count of every time internal page was accessed.
12. EXTERNAL PAGE USED: Peg count for every time external page was accessed.
13. ALL PAGE USED: Peg count of every time the all page feature was accessed.This does not include internal or
external page, only 55+ or PAGE .
B**************************** TRUNK GROUPS **************************
1 GROUP
9
800
801
2 OUTGOING
0000
0000
0000
3 BUSY
0000
0000
0000
1. GROUP: A listing of all trunk groups assigned in the system.
2. OUTGOING: These are the number of outgoing trunk calls made using each trunk group. Pegged every time
a member of this trunk group was used to make a valid outgoing call. A valid outgoing call is defined by the
SMDR Start Time programmed in MMC 501.
3. BUSY: This is the number of times each trunk group was busy when someone attempts to access it.
C****************************** INDIVIDUAL TRUNKS ***************************
1TRUNK
701
702
703
704
705
706
707
708
709
710
2TRUNK-NAME
3ATTA
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
4ANSD
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
5NOT-ANSD
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
6OUTGOING
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
7BUSY
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
1. TRUNK: A listing of each trunk in the system.
2. TRUNK NAME: The names of each trunk as programmed in MMC 404.
3. ATTA: Average Time To Answer for trunks is counted in the number of seconds that ringing voltage is detected at the trunk interface and the timer stops when trunk is answered by station or device in the system. The
ATTA is the sum of all answered times divided by the answered call count.
4. ANSD: This is the number of times this specific trunk was answered by any station or device whether it is a
new call or a recall.
5. NOT-ANSD: This is the number of times this specific trunk rang the system but was not answered. These are
the same calls that would be flagged as abandoned in SMDR.
4.52
6. OUTGOING: This is the number of times this trunk was used to make an outgoing call. A valid outgoing call
is defined by the SMDR START TIME programmed in MMC 501.
7. BUSY: This is the number of times this trunk was busy when accessed by a button or dial code.
D**************************** STATION HUNT GROUPS **************************
2GROUP
500
501
502
503
504
<————————
1 OUTSIDE CALL —————————————————————>
3ANSD
4NOT-ANSD
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
5 <-INTERCOM->
6ANSD
0000
0000
0000
0000
0000
1. OUTSIDE CALLS: These statistics are for outside calls that reach these station groups regardless how they
arrive there.
2. GROUP: Listing of all station groups in the system.
3. ANSD: This column is a peg count of all answered trunk calls that rang to the specific group directory number regardless of how these arrived.
4. NOT-ANSD: The number of times any trunk call directed to the specific group number was not answered by
any member of the group.
5. INTERCOM: An intercom call made from a station or device within the system to the specific group number.
6. ANSD: This is a count of how many times an intercom call was answered by any group member of that specific group.
E**************************** INDIVIDUAL STATIONS ***************************
1
11
<—————————————————— OUTSIDE CALL —————————————————> <-INTERCOM->
2
3
4
5
6
7
8
9
10
12
13
EXT STATION-NAME ATTA ANSD NOT-ANSD DIALED ICM-TRSF TRK–TRK PICKUP ANS DIALED
201
0000 0000 0000
0000
0000
0000
0000 0000 0000
202
0000 0000 0000
0000
0000
0000
0000 0000 0000
203
0000 0000 0000
0000
0000
0000
0000 0000 0000
204
0000 0000 0000
0000
0000
0000
0000 0000 0000
205
0000 0000 0000
0000
0000
0000
0000 0000 0000
1. OUTSIDE CALLS: These statistics are for outside calls that in any way reach individual stations or devices.
2. EXT: Listing of all extension numbers in the system. This also includes AA, VM, and CADENCE ports.
3. STATION NAME: The name for each particular station as programmed in MMC 104.
4. ATTA: Average Time To Answer for stations is counted in the number of seconds that ringing signal is applied
to a station for trunk calls and recalls.The ATTA is the sum of all answered times divided by the answered call
count. Use the same calculation method as used for individual trunk ATTA.
4.53
5. ANSD: This is a count of how many times an outside call was answered by the specific station. Outside callers
recalling a station are not counted again when they are answered.
6. NOT-ANSD: This is a count of how many times a trunk call was directed to the station but was not answered
by this station.
7. DIALED: Peg count of how many times the station made a valid outside call. An outside call is defined by the
SMDR start time in MMC 501.
8. ICM-TRSF: This is the number of times a trunk call was successfully transferred to another station using the
intercom. It includes both screened and unscreened transfer.
9. TRK–TRK: This is the number of times a trunk call was transferred to another trunk (tie line) This is called a
trunk–to–trunk transfer. This field gets pegged every time the station completes a trunk to trunk transfer.
10. PICKUP: This is a count of the outside calls that were picked up by the specific station. Picked-up calls are calls
that are not ringing at your station but were answered by you. This peg count is separate from the number
of answered call in #5 of Individual Stations section E.
11. INTERCOM: Statistics for intercom calls. An intercom call made from a station or a station device within the
system to another station.
12. ANSD: This is the number of times an intercom call was answered by this specific station. Screened transfers
count as an answered intercom call.
13. DIALED: The number of times the specific station dialed another station or station group. Screened transfers
count as a dialed intercom call.
4.54
PART 5. GENERAL USER INFORMATION
5.1 RADIO FREQUENCY INTERFERENCE
WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy. If not installed and operated in accordance with the instruction manual, it may
cause interference with radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
The following measures can be tried:
1.
2.
3.
4.
Reorient the receiving antenna.
Relocate the telephone with respect to the receiver.
Move the telephone equipment away from the receiver.
Plug the Key Service Unit into a different AC outlet so that the KSU and receiver are on different circuits.
5.2 FCC REQUIREMENTS
The OfficeServ 500 electronic telephone system complies with Part 68 of the Federal Communications
Commission Rules and Regulations.
UNAUTHORIZED MODIFICATIONS
Any changes or modifications performed on this equipment that are not expressly approved in writing by SAMSUNG TELECOMMUNICATIONS AMERICA could cause noncompliance with the FCC rules and void the user’s
authority to operate the equipment.
NOTE: Allowing this equipment to be operated in such a manner as to not provide for proper answer supervision
is a violation of Part 68 of the FCC’s rules.
NOTIFICATION TO TELEPHONE COMPANY
Before connecting the OfficeServ 500 system to the telephone network, the telephone company may request the
following information:
•
•
•
•
Your telephone number or all numbers that will be connected to the OfficeServ 500 system.
FCC Registration Numbers:
Key System—Fully Protected
A3LKOR-43066-KF-E
Multi-Function (Hybrid)—Fully Protected
A3KLOR-43065-MF-E
Ringer Equivalence Number 0.5 B for TRK-B1
Ringer Equivalence Number 1.6 B for TRK-C1
The OfficeServ 500 may be configured as a key system or a hybrid system. Depending on the method of operation, the appropriate FCC number must be given to the telephone company. Certain features such as pooled
access by button or dial access, LCR, off premise extensions and tie lines may require the hybrid registration.
Check with the local telephone company providing the service if you are in doubt. It is the customer’s responsibility to comply with local telephone company tariffs.
5.1
TELEPHONE CONNECTION REQUIREMENTS
The Federal Communications Commission (FCC) has established rules which permit the DCS to be connected
directly to the telephone network using telephone company network access jacks usually referred to as
“Registered Jacks.”
5.3 TELEPHONE COMPANY INTERFACES
CIRCUIT
TYPE
LOOP START LINE
OFFICESERV 500
CARD TYPE
FACILITY
INTERFACE CODE
TRK-B
TRK-B1
TRK-C1
T1-SF
T1-ESF
O2LS2
OFF PREMISES EXTENSION
SLI-4 circuit board only
OL13C
E911
E911
O2RV2-O
ISDN-PRI
TE/PRI
04DU9-1KN
ISDN-BRI
4BRI
02155
NETWORK
JACK
04DU9-DN
04DU9-1KN
RJ21X
RJ11C
RJ14C
RJ48C
RJ21X
RJ11C
RJ14C
RJ48C
NT1
RINGER EQUIVALENCE (REN)
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most but not
all areas, the sum of the RENs should not exceed 5.0.To be certain of the number of devices that may be connected to the line, as determined by the number of RENs, contact the telephone company to determine the maximum
REN for the calling area.
INCIDENCE OF HARM
If the terminal equipment, the OfficeServ 500, causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
CHANGES TO TELEPHONE COMPANY EQUIPMENT OR FACILITIES
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect
the operation of the equipment. If this happens, the telephone company will provide advance notice in order for
you to make the necessary modifications so that you may maintain uninterrupted service.
SERVICE CENTER
If trouble is experienced with the OfficeServ 500, please contact your local SAMSUNG TELECOMMUNICATIONS
AMERICA for repair or warranty information. If the trouble is causing harm to the telephone network, the telephone company may request that you remove the equipment from the network until the problem is resolved.
5.2
FIELD REPAIRS
Only technicians certified on the OfficeServ 500 are authorized by SAMSUNG TELECOMMUNICATIONS AMERICA
to perform system repairs. Certified technicians may replace modular parts of a system to repair or diagnose trouble. Defective modular parts can be returned to SAMSUNG TELECOMMUNICATIONS AMERICA for repair.
GENERAL
This equipment must not be used on coin telephone lines. Connection to party line service is subject to state tariffs.
The OfficeServ 500 system uses toll restriction and LCR features that are programmed to allow dialing over the
public telephone network. The North American Numbering Plan (NANP) determines these network area codes
and exchange codes. Failure to update the system programming or software may deny you access to new area
codes and exchanges. Bell Communication Research (Bellcore) administers the NANP and publishes it. To obtain
the latest information and keep your system current, contact Bellcore at (201) 829-3071.
HEARING AID COMPATIBILITY
All models of the OfficeServ 500 are hearing aid compatible as specified in Part 68 of the FCC Rules.
5.4 UNDERWRITERS LABORATORIES
The OfficeServ 500 system has been tested to comply with safety standards in the United States as listed below.
This system is listed with Underwriters Laboratories.
C
US
LISTED
51Y7
E149091
I.T.E
5.5 MUSIC ON HOLD WARNING
IMPORTANT NOTICE: In accordance with US copyright laws, a license may be required from the American Society
of Composers, Authors and Publishers (ASCAP) or other similar organizations if copyrighted music is transmitted
through the Music on Hold feature. SAMSUNG TELECOMMUNICATIONS AMERICA hereby disclaims any liability
arising out of failure to obtain such a license.
5.6 EQUAL ACCESS REQUIREMENTS
The OfficeServ 500 is capable of providing users access to interstate providers of operator services through the
use of access codes. Modifications of this equipment by call aggregators to block access dialing codes is a violation of the Telephone Operator Consumer Act of 1990 and Part 68 of the FCC Rules.
5.7 DISA WARNING
Lines that are used for the Direct Inward System Access feature must have the disconnect supervision options
provided by the telephone company.
WARNING: As it is impossible to control who may access your DISA line it is suggested that you do not turn this
feature on unless you intend to use it. If you do use this feature, it is good practice to frequently change passcodes and periodically review your telephone records for unauthorized use.
5.3
PART 6. HOTEL / MOTEL FEATURE PACKAGE
6.1 GENERAL OVERVIEW
The OfficeServ 500 Hotel / Motel software package combines the OfficeServ 500 business features with additional features created to meet the needs of the Hotel / Motel industry. This combination meets the requirements of
the Hotel General Business offices as well as those of the Hotel Guest. The OfficeServ 500 Hotel / Motel package
MUST be activated in MMC 813 before it can be used.
Samsung’s OfficeServ 500 Hotel / Motel software is designed to operate in small to medium sized hotel properties. Those with, up to approximately, 300 rooms.
The OfficeServ 500 Hotel / Motel software offers a bi-directional PMS link. All system transactions related to the
guest and meeting rooms will be sent to the PMS system via this link. Likewise any information input from a PMS
or POS terminal will be sent into the OfficeServ 500 via this same link. Station status can be changed via these
PMS and POS PC terminals. Message lights can be activated, Do Not Disturb can be set, etc, across the PMS link.
The system’s design makes it operational without the need for additional PMS equipment.The key to utilizing the
Hotel / Motel software without an external PMS is the front desk display keyset. The keyset can be programmed
with features and functions pertinent to the hospitality industry, that make it convenient to perform day to day
routine functions. However in the case of larger hotels, the owner / operator would probably choose to interface
to the bi-directional PMS link.
For those systems that are not utilizing a PMS software package, the OfficeServ 500 Hotel / Motel software will
maintain a record of all transactions that occur throughout the system. These records are maintained until the
guest is checked out. The OfficeServ 500 will maintain 10,000 transaction records. These transaction records represent one line of the guest room bill. These records are purged once the room is checked out.
6.1
6.2 HOTEL / MOTEL FEATURES
Bi-Directional PMS
Room Status
Printed Reports
Call Costing
Keyset Indications
Check In
Check Out
Room Status Update
Automatic (Daily Timer)
Deposit Posting
Manual
DSS Key Use During Feature Activation
Enhanced User Programming
Staff I.D. Codes (500)
Executive DND
Station Types
Express Check-In
Business Office
Guest Services Billing
Hotel Administrator
Meeting Room
100 Item Codes with Costing
Lobby Phone Service
Guest No Smoking Room
Printed Reports
Guest Smoking Room
Fax Station
Phone Bill
Guest and Meeting Room Bill
Telephone Credit Limit
Room Status
Transaction Record Output (To PMS)
Wake Up Call Activity
Wake Up Calls
Room Dialing Restrictions
Set by Attendant
Room Rate Discounts
Set by Guest
Room Status Conditions
Answered
Available
Not Answered
Occupied
Cancelled
Needs Cleaning
With Auto Attendant Announcement
Needs Maintenance
Hold (Late Check Out)
Hold and Needs Cleaning
Hold and Needs Repair
Cleaned
Repaired
BI-DIRECTIONAL PMS
The OfficeServ 500 offers a bi-directional PMS link.This link allows for the integration of a PC, with a PMS software package installed, to be utilized for inputting room related charges as well as creating room bills,
reports, etc. Any transactions, related to guest or meeting rooms, that take place within the hotel system, will
be sent immediately to this link from the OfficeServ 500.
Also, any information input at a PMS or POS terminal will be sent into the OfficeServ 500 via this same link.
This link will allow for system billing and room status information to be updated via PMS and POS, PC terminals.
CALL COSTING
The OfficeServ 500 Hotel / Motel software provides call costing, for guest and meeting room phones.The call
cost will appear on the guest’s room bill, the SMDR report, the transaction record output, and the PMS output.
The system uses programmable call costing tables to calculate the cost of incoming and outgoing calls. Rates
are calculated by the number dialed, duration of the call and may include surcharges.
6.2
CHECK IN
The OfficeServ 500 Hotel / Motel software allows an Administrator keyset to check a guest into a room by
pressing the CHECK IN key and following the prompts in the display. When the CHECK IN key is pressed the
clerk can credit the room account if the guest wishes to prepay for the room and/or the phone service. The
clerk can also assign the guest’s name to the room.
This feature offers 64-Button Module support. Meaning that the associated DSS key assigned to a 64-Button
Module, can be used to enter the room number that is being checked in.
CHECK OUT
In addition the feature allows an Administrator keyset to check a guest out of a room by pressing the CHECK
OUT key. The CHECK OUT option will print out the total room charges and clear the room information from
the transaction record buffer. It also changes the room to the Needs Cleaning status. Checking a guest out of
a room prior to the ROOM CLEAN TIME will automatically change the room to the NEEDS CLEANING status.
This feature offers 64-Button Module support. Meaning that the associated DSS key assigned to a 64-Button
Module, can be used to enter the room number that is being checked out.
DEPOSIT POSTING
The credit feature allows any Administrator keyset to add a cash deposit to a room bill, to offset charges
already incurred or to prepay either the room or phone charges or both. This feature requires a CREDIT key
to be assigned to the administration phones.This feature offers 64-Button Module support. Meaning that the
associated DSS key assigned to a 64-Button Module, can be used to enter the room number that the deposit
is being posted to.
DSS KEY USE DURING FEATURE ACTIVATION
When utilizing the Administrator keyset to activate system features / functions, many will request the room
number to be entered. In most cases the associated DSS key can be pressed to enter the station number.
The exceptions are Wake Up Call Setting and Lobby Phone Service.These features will not respond to the DSS
key press. The associated station number must be assigned via the keypad.
ENHANCED USER PROGRAMMING
The OfficeServ 500 allows the System Administrator access to several non-volatile MMCs. These MMCs give
stations assigned as ADMINISTRATOR and NORMAL, the ability to change Station Call Forwarding, System
Time and Date, etc. for any station within the system.
This Enhanced System Programming is accessible through the PROG key.
The MMCs available to Enhanced User Programming are as follows: MMC 100: Station Lock, MMC 102: Call
Forward, MMC 104: Station Name, MMC 115: Set Programmed Message, MMC 116: Alarm and Message, MMC
505: Assign Date and Time, MMC 705: Assign System Speed Dial, MMC 706: System Speed Dial by Name, and
MMC 722: Station Key Programming.
EXECUTIVE DND
The Executive DND feature (SET DND key) allows Front Desk personnel to set and cancel DND to a guest’s
room. This means that a guest can request that their room be flagged as DND, saving the guest from having
to learn system feature codes. This key will allow Front Desk personnel to change DND status, as an additional guest service.
6.3
This feature can be set and canceled from the guest room phone. This feature offers 64-button module support. Meaning that the associated DSS key assigned to a 64-button module can be used to enter the room
number to set DND to.
EXPRESS CHECK-IN
This feature is designed to expedite the Check In procedure. It is a second check in option. It is used expressly to check in a guest quickly.
The Express Check In feature (X-CHIN key) eliminates several steps from the standard Check In procedure.This
feature does not request any billing type, or guest’s name information.
This feature offers 64-button module support. Meaning that the associated DSS key assigned to a 64-button
module, can be used to enter the room number that is being checked in.
GUEST SERVICES BILLING
The guest service billing feature allows a staff member, to enter an item code and a dollar amount to a specific room bill using specific telephone stations. The dollar amount entered at time of sale for the item code,
can be multiplied by the tax rates defined for the items or will have the tax amount added if the tax is a fixed
dollar amount.
There are 100 item codes in the system. Each item code can have a name, with up to 10 characters, programmed to describe the charge.
This feature requires a staff ID code to be entered to add or delete a charge to a room. The staff ID codes are
assigned in the Authorization Code table. The staff ID code will be verified from the table, and if an incorrect
code is entered, an error tone will be returned and the station will return to idle.
The room number will also be verified, from the list of rooms that are checked in. If a room number is not
occupied, an error tone will be returned and the station will return to idle.
This feature can be used by either a keyset or a single line telephone with DTMF dialing. The keyset requires
a BILL key.
LOBBY PHONE SERVICE
This feature allows a hotel operator to bill a call to a guest room even though it was made at a remote location, such as a lobby phone. This phone can be a dial “0” type or a Hotline to the operator.
The guest will request the operator to bill an outside call to his/her room.The operator will press the Remote
Bill key (RB) and place the guest on transfer hold, then enter the guest’s room number and receive confirmation tone.The operator can then dial the number for the guest and transfer the ringing call back to the guest.
PRINTED REPORTS
In those cases where the bi-directional PMS link is not used, the OfficeServ 500 Hotel / Motel software package will provide various printed reports of selected activities throughout the system. These reports are initiated from any administrator’s display keyset and sent to a printer connected to the network or through a serial port on the IOM card. This serial IOM port will assigned as HM REPT.
In order to provide a permanent record, it is advisable to use two-part paper in the printer, or do a room bill
printout, prior to checking the room out.
6.4
Phone Bill
The Phone Bill report provides only the phone bill information for a specific room. This print out is separate
from the guest room bill.This allows a guest to pay for them separately, so no phone calls appear on the room
bill.When using this feature you have the option of saving or deleting all telephone call information from the
guest’s bill.
The information in the phone bill includes the date and time the report was requested, the room number
requested, date and time of call, the number dialed, call duration and the charge for the call.
Guest and Meeting Room Bill
This printout includes all room-related charges, from time of check in. Associated taxes and/or surcharges are
automatically calculated by the system based on programmable rate table entries. Any deposits made are
automatically deducted from the total bill.This printout also includes daily room charges, phone calls, services charged to the room, wake up call activity, and any deposits made. This printout is made on a per room
basis.
Room Status
The system can print six different Room Status reports. There are five (5) individual reports for the following
room status conditions: Available, Occupied, Needs Cleaning, Needs Maintenance, and Hold for Late
Checkout. A sixth report will show all rooms and all room status conditions.
Wake Up Call Activity
This report will detail all wake up call information related to a specific room since check in. The printout
includes the time a wake up call was set, the requested wake up time, the time the call was answered, unanswered wake up calls, canceled wake up calls and charges for the service if programmed.
Room Dialing Restrictions
This feature is used to program station to station calling restrictions and is sometimes referred to as intercom
blocking. For instance you can restrict rooms from dialing the administration offices while still being able to
dial the front desk, other hotel service phones or other guest rooms.
Room Rate Discounts
The OfficeServ Hotel / Motel software offers a method of discounting room rates, on a day-by-day basis. This
discount is based on a percentage of the full room rate. The percentage is programmable and variable.
Room Status Conditions
The system will indicate the status of each guest or meeting room when requested. See Room Status.The five
possible conditions are (the last four conditions in the list are sent to update PMS information only):
•
AVAILABLE – Ready to check in.
•
OCCUPIED – Guest is checked in.
•
NEEDS CLEANING – Condition after check out or morning update for all occupied rooms.
•
NEEDS MAINTENANCE – Temporary condition for rooms requiring some repair or maintenance.
•
HOLD (LATE CHECK OUT) – Indicates a guest requires a late check out so hotel staff will delay cleaning.
•
CLEANED – Message sent for updating PMS. Indicates that the room has been cleaned.
•
REPAIRED – Message sent to update PMS. Indicates that the room has been repaired.
6.5
•
HOLD AND NEED CLEANING – Message sent to update PMS. Indicates that the room is being held and
requires cleaning.
•
HOLD AND NEEDS MAINTENANCE – Message sent to update PMS. Indicates that the room is being held
and requires maintenance.
ROOM STATUS
The OfficeServ 500 Hotel / Motel system provides three methods to review the five room status conditions.
1.
An administrator’s display keyset can be used to view the status of any individual room and scroll
through the list of all other rooms to view their status.
2.
One or more 64 Button Modules can be used to view the status of all rooms for any of the five room conditions (Example: press the Room Status View key for “AVAILABLE” and all the buttons corresponding to
available rooms will light red).
3.
Printed reports can be obtained to review the room status conditions for all rooms. See Printed
Reports–Room Status, earlier in this document.
ROOM STATUS UPDATE
The system operation provides two methods to update the status of each guest or meeting room.
Automatic
The hotel manager informs the system technician of the preprogrammed time he wants all rooms to automatically change from “Occupied” to “Needs Cleaning” on a daily basis. In addition each room is automatically changed to “Needs Cleaning” upon check out.
Manual
Hotel personnel, such as maids, maintenance men or administrators, can dial a code from the guest/meeting
room telephone to manually update the room status as required.
The manual room status update codes are:
0= Room needs to be cleaned.
1= Room cleaned. This updates the room status to either AVAILABLE or OCCUPIED.
2= Room needs maintenance. This makes the room NOT AVAILABLE for check in.
3= Room repaired. This updates the room status to either AVAILABLE or OCCUPIED.
STAFF I.D. CODES
These are simply Authorization Codes that hotel employees must enter to access various Hotel / Motel features. These codes will appear on the Room Bill printout to indicate who posted the charges to a specific
room. They provide a measure of security and control for hotel management. There are 500 STAFF ID codes
in the software.
6.6
STATION TYPES
The system software enables station ports to be defined for a specific use throughout the hotel. Each telephone can be designated as being one of the five following types. A class of service has been established for
each station type.
1.
NORMAL STATION – This is the default setting. The station will operate in the manner associated with a
normal business station.
2.
ADMINISTRATOR – Only stations designated as Administrator can access special Hotel / Motel features,
such as Check In, Check Out, Room Status, Print Report, etc.
3.
MEETING ROOM – A meeting room is similar to a guest room in the respect that it generates a room bill
but has different class of service option requirements.
4.
GUEST NO SMOKING – When a station is designated as this type, it will appear in the administrator’s keyset display as a no smoking room. This station type will generate a room bill and follow its associated
class of service options.
5.
GUEST SMOKING – When a station is designated as this type, it will appear in the administrator’s keyset
display as a smoking room. This station type will generate a room bill and follow its associated class of
service options.
6.
FAX STATION – When a station is designated as this type, the associated station number can be paired
with a fax extension so that calls from the fax extension can be billed to the room..
TELEPHONE CREDIT LIMIT
This feature is designed to control phone charges for hotel guests that do not use a credit card. These guests
will need to make a cash deposit for their phone calls. When the credit warning threshold has been reached
the guest will receive two beeps in their ear, (the warning threshold is determined by the COST RATE feature
and occurs one billing period prior to the credit limit being reached).When the credit limit is reached, the call
will be dropped, and the phone will then be restricted. An additional cash deposit is required to re-activate
the phone.
TRANSACTION RECORD OUTPUT
The OfficeServ 500 Hotel / Motel software provides an output for all Hotel / Motel transactions. Any transactions, related to guest or meeting rooms, that take place within the hotel system, will be immediately sent
–”on the fly” to a serial port on the IOM card. The serial port will be assigned as PMS. This transaction stream
would typically be connected to a PC with a PMS software package, for system reports.
WAKE UP CALLS
The OfficeServ 500 Hotel / Motel software package supports a comprehensive wake-up feature.
•
SET BY ATTENDANT – The hotel administrator stations or operator/attendant can set a wake call.
•
SET BY GUEST – Each hotel guest can set his/her own wake up call using the telephone in their room.
•
ANSWERED – Both the guest room bill and wake up call activity report will show the date and time the
guest answered the wake up call.
•
NOT ANSWERED – Both the guest room bill and wake up call activity report will show each wake up call
attempt that was not answered by the hotel guest.This information will print out on the printer connected to the serial port designated for the Hotel / Motel Report.
6.7
•
CANCELED – Both the guest room bill and wake up call activity report will indicate each canceled wake
up call. Only Hotel / Motel administrator’s keysets can cancel wake up calls. The guest can reprogram a
wake up request if he made a mistake. System programming provides a programmable number of wake
up call attempts and a programmable time interval between attempts.
•
WITH AUTO ATTENDANT ANNOUNCEMENT – The system can be programmed to play one of the 64 automated attendant messages when a guest answers a wake up call.This message can be one of the 16 prerecorded messages or one of the 48 customer recorded messages.
Note: It is recommended that the recording used as the Wake Up Announce Recording, be the last
recorded message. This will minimize the amount of re-recording needed, should the message need to
be changed.
6.8
6.3 SAMPLE REPORTS AND PRINTOUTS
6.3.1 GUEST ROOM BILL PRINTOUT
6.3.2 ROOM STATUS PRINTOUTS
– AVAILABLE
– OCCUPIED
– NEEDS CLEANING
– NEEDS MAINTENANCE
– HOLD
– ALL
6.3.3 TRANSACTION RECORD OUTPUT SAMPLE
6.3.4 INDIVIDUAL GUEST PHONE BILL
6.3.5 ALL GUEST PHONE BILL (SMDR)
6.3.6 INDIVIDUAL WAKEUP ACTIVITY REPORT
6.3.7 SAMPLE GUEST PHONE TEMPLATES
6.9
6.3.1 GUEST ROOM BILL PRINTOUT
Printout includes the following information:
Date and time the bill was printed
Room number requested
Daily room charge
Phone calls and their charges
Wake up call activity
–
Time wake up was set for
–
Each wake up call attempt, answered/not answered
–
Cancelled wake up
Room related charges and applicable taxes
Item codes and associated descriptions for room related charges
–
Details column
–
Staff code of employee performing function
–
Duration of phone calls
–
Time wake up call was set for
Room and/or phone deposits
Total room charges
55 LINES
Date and time item was billed
Automatically increments the daily room charge
Automatically applies room and phone deposits to the total bill
Room bills are printed on a per room basis
By default, printout will print a header, followed by 50 lines per page
Printout size is adjustable through programming
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.10
GUEST BILL FROM [SUNSHINE SUITES ]
01/28/99
14:13
CHARGES BILLED TO ROOM NUMBER : 210
ROOM
DATE
TIME
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
210
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/27
01/28
01/28
01/28
01/28
01/28
01/28
01/28
01/28
01/28
01/28
12:11
12:11
12:11
12:11
12:30
12:30
12:30
12:31
14:55
14:55
14:55
14:55
14:58
14:58
15:01
15:01
15:01
19:35
06:00
06:01
06:30
06:30
06:30
12:00
12:00
12:00
13:32
14:06
ITEM
DESCRIPTION
02
02
02
00
03
03
03
TEL
89
05
05
TEL
01
TEL
92
04
04
89
91
90
03
03
03
02
02
02
TEL
TEL
RM CHARGE
STATE TAX
BED TAX
RM Deposit
RM SVC
STATE TAX
SVC CHARGE
3055922900
W/UP SET
MOVIE RNTL
STATE TAX
18008764782
PH Deposit
3055922900
W/UP CANCL
DRY CLEAN
SVC CHARGE
W/UP SET
W/UP N/ANS
W/UP ANS
RM SVC
STATE TAX
SVC CHARGE
RM CHARGE
STATE TAX
BED TAX
18008764782
3055922900
DETAILS
1234
5555
9876
00:00:49
05:30
5555
00:02:03
1234
00:02:18
1234
06:00
5555
00:01:59
00:01:03
TOTAL
Page
Sunshine
1 of
CHARGE
100.00
6.00
1.50
-100.00
20.00
1.20
2.00
.75
000.00
5.00
.30
.25
-2.50
1.25
000.00
22.00
2.00
000.00
000.00
000.00
18.50
1.11
2.00
100.00
6.00
1.50
.25
.75
189.86
1
Suites
6.11
6.3.2 ROOM STATUS PRINTOUT
Printout includes the following information:
Date and time the report was printed
Status of guest and meeting rooms
–
On an individual, status type basis
OR
–
Room Status Printout Types:
–
AVAILABLE
–
OCCUPIED
–
NEEDS CLEANING
–
NEEDS MAINTENANCE
–
HOLD
–
ALL
Room status is updated by either the administrator access, automatic room update or maid codes.
55 LINES
As a complete report of all rooms and their status
By default, the printout will print a header followed by 50 lines per page
Printout size is adjustable through programming
NOTE: Systems utilizing the optional 64 button module, can temporarily display room status, when a printout
is not needed.
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OfficeServ 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.12
ROOM STATUS PRINTOUT
ROOM
STATUS
AVAILABLE
ROOM
STATUS
11:59
12/02
ROOM
STATUS
209
AVAILABLE
220
AVAILABLE
213
AVAILABLE
215
AVAILABLE
217
AVAILABLE
219
AVAILABLE
220
AVAILABLE
221
AVAILABLE
223
AVAILABLE
225
AVAILABLE
226
AVAILABLE
227
AVAILABLE
228
AVAILABLE
301
AVAILABLE
302
AVAILABLE
303
AVAILABLE
304
AVAILABLE
306
AVAILABLE
307
AVAILABLE
403
AVAILABLE
405
AVAILABLE
406
AVAILABLE
407
AVAILABLE
409
AVAILABLE
Sunshine
Suites
6.13
ROOM STATUS PRINTOUT
Printout includes the following information:
Date and time the report was printed
Status of guest and meeting rooms
–
On an individual, status type basis
OR
–
Room Status Printout Types:
–
AVAILABLE
–
OCCUPIED
–
NEEDS CLEANING
–
NEEDS MAINTENANCE
–
HOLD
–
ALL
Room status is updated by either the administrator access, automatic room update or maid codes.
55 LINES
As a complete report of all rooms and their status
By default, the printout will print a header followed by 50 lines per page
Printout size is adjustable through programming
NOTE: Systems utilizing the optional 64 button module, can temporarily display room status, when a printout
is not needed.
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.14
ROOM STATUS PRINTOUT
ROOM
STATUS
OCCUPIED
ROOM
13:56
11/02
STATUS
ROOM
STATUS
211
OCCUPIED
212
OCCUPIED
214
OCCUPIED
216
NEED MAINTENANCE
218
OCCUPIED
222
OCCUPIED
224
OCCUPIED
305
OCCUPIED
308
NEEDS CLEANING
309
HOLD
310
NEEDS MAINTENANCE
401
NEEDS CLEANING
402
NEED MAINTENANCE
404
NEEDS CLEANING
408
NEEDS CLEANING
Sunshine
Suites
6.15
ROOM STATUS PRINTOUT
Printout includes the following information:
Date and time the report was printed
Status of guest and meeting rooms
–
On an individual, status type basis
OR
–
Room Status Printout Types:
–
AVAILABLE
–
OCCUPIED
–
NEEDS CLEANING
–
NEEDS MAINTENANCE
–
HOLD
–
ALL
Room status is updated by either the administrator access, automatic room update or maid codes.
55 LINES
As a complete report of all rooms and their status
By default, the printout will print a header followed by 50 lines per page
Printout size is adjustable through programming
NOTE: Systems utilizing the optional 64 button module, can temporarily display room status, when a printout
is not needed.
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.16
ROOM STATUS PRINTOUT
ROOM
STATUS
NEEDS CLEANING
ROOM
STATUS
13:50
11/02
ROOM
STATUS
211
NEEDS CLEANING
212
NEEDS CLEANING
214
NEEDS CLEANING
215
NEEDS CLEANING
218
NEEDS CLEANING
220
NEEDS CLEANING
222
NEEDS CLEANING
224
NEEDS CLEANING
303
NEEDS CLEANING
305
NEEDS CLEANING
310
NEEDS CLEANING
401
NEEDS CLEANING
404
NEEDS CLEANING
408
NEEDS CLEANING
Sunshine
Suites
6.17
ROOM STATUS PRINTOUT
Printout includes the following information:
Date and time the report was printed
Status of guest and meeting rooms
–
On an individual, status type basis
OR
–
Room Status Printout Types:
–
AVAILABLE
–
OCCUPIED
–
NEEDS CLEANING
–
NEEDS MAINTENANCE
–
HOLD
–
ALL
Room status is updated by either the administrator access, automatic room update or maid codes.
55 LINES
As a complete report of all rooms and their status
By default, the printout will print a header followed by 50 lines per page
Printout size is adjustable through programming
NOTE: Systems utilizing the optional 64 button module, can temporarily display room status, when a printout
is not needed.
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.18
ROOM STATUS PRINTOUT
ROOM
216
STATUS
NEED MAINTENANCE
ROOM
NEED MAINTENANCE
STATUS
14:01
ROOM
308 NEED MAINTENANCE 402
Sunshine
11/02
STATUS
NEED MAINTENANCE
Suites
6.19
ROOM STATUS PRINTOUT
Printout includes the following information:
Date and time the report was printed
Status of guest and meeting rooms
–
On an individual, status type basis
OR
–
Room Status Printout Types:
–
AVAILABLE
–
OCCUPIED
–
NEEDS CLEANING
–
NEEDS MAINTENANCE
–
HOLD
–
ALL
Room status is updated by either the administrator access, automatic room update or maid codes.
55 LINES
As a complete report of all rooms and their status
By default, the printout will print a header followed by 50 lines per page
Printout size is adjustable through programming
NOTE: Systems utilizing the optional 64 button module, can temporarily display room status, when a printout
is not needed.
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.20
ROOM STATUS PRINTOUT
ROOM
STATUS
212
HOLD
401
HOLD
HOLD
ROOM
214
Sunshine
11:58
STATUS
HOLD
12/02
ROOM
309
STATUS
HOLD
Suites
6.21
ROOM STATUS PRINTOUT
Printout includes the following information:
Date and time the report was printed
Status of guest and meeting rooms
–
On an individual, status type basis
OR
–
Room Status Printout Types:
–
AVAILABLE
–
OCCUPIED
–
NEEDS CLEANING
–
NEEDS MAINTENANCE
–
HOLD
–
ALL
Room status is updated by either the administrator access, automatic room update or maid codes.
55 LINES
As a complete report of all rooms and their status
By default, the printout will print a header followed by 50 lines per page
Printout size is adjustable through programming
NOTE: Systems utilizing the optional 64 button module, can temporarily display room status, when a printout
is not needed.
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.22
ROOM STATUS PRINTOUT
ROOM
STATUS
ALL
13:58
ROOM
11/02
STATUS
ROOM
STATUS
209
AVAILABLE
210
AVAILABLE
211
OCCUPIED
212
OCCUPIED
213
AVAILABLE
214
NEEDS CLEANING
215
NEEDS CLEANING
216
NEED MAINTENANCE
217
AVAILABLE
218
NEEDS CLEANING
219
AVAILABLE
220
NEEDS CLEANING
221
AVAILABLE
222
NEEDS CLEANING
223
AVAILABLE
224
NEEDS CLEANING
225
AVAILABLE
226
AVAILABLE
227
AVAILABLE
228
OCCUPIED
301
OCCUPIED
302
OCCUPIED
303
NEEDS CLEANING
304
AVAILABLE
305
NEEDS CLEANING
306
AVAILABLE
307
AVAILABLE
308
NEED MAINTENANCE
309
HOLD
310
NEEDS CLEANING
401
NEEDS CLEANING
402
NEED MAINTENANCE
403
AVAILABLE
404
HOLD
405
AVAILABLE
406
OCCUPIED
407
AVAILABLE
408
NEEDS CLEANING
409
AVAILABLE
Sunshine
Suites
6.23
6.3.3 TRANSACTION RECORD OUTPUT SAMPLE
The PMS output stream includes information from all transactions within the Hotel / Motel system. This is a
one way output only, from the phone system to the PMS system.
This information includes:
Check In confirmation with:
–
Room charges and applicable taxes
–
Updated room status
Check Out information with:
–
Updated room status
Room related charges and applicable taxes
Daily room charge updates
Room / phone deposits
Maid / maintenance room status updates
Phone calls and charges
Wake up calls time set for
Unanswered wake up calls
Cancelled wake up calls
55 LINES
The system outputs this information immediately after transaction is completed.
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.24
211
211
211
211
211
209
209
209
216
213
214
211
211
209
216
217
209
209
209
209
210
210
210
210
213
213
213
213
215
215
215
215
216
216
216
216
217
217
217
217
216
216
216
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/29
01/30
01/30
06:10
06:10
06:10
06:10
06:10
06:11
06:11
06:11
06:11
06:11
06:12
06:13
06:13
06:12
06:15
06:16
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
12:00
15:38
06:00
06:01
02
02
02
93
96
03
03
03
89
TEL
00
94
97
TEL
92
07
02
02
02
97
02
02
02
97
02
02
02
97
02
02
02
97
02
02
02
97
02
02
02
97
89
91
90
RM CHARGE
STATE TAX
BED TAX
Check In
Occupied
RM SVC
STATE TAX
SVC CHARGE
W/UP SET
3055922900
RM Deposit
Check Out
Clean Room
18008764782
W/UP CANCL
MISC
RM CHARGE
STATE TAX
BED TAX
Clean Room
RM Charge
STATE TAX
BED TAX
Clean Room
RM CHARGE
STATE TAX
BED TAX
Clean Room
RM CHARGE
STATE TAX
BED TAX
Clean Room
RM CHARGE
STATE TAX
BED TAX
Clean Room
RM CHARGE
STATE TAX
BED TAX
Clean Room
W/UP SET
W/UP N/ANS
W/UP ANS
5555
5555
5555
9876
06:00
00:00:34
1234
00:01:29
5555
06:00
69.99
4.19
1.50
000.00
000.00
25.00
1.50
2.00
000.00
.75
-20.00
000.00
000.00
.25
000.00
150.00
100.00
6.00
1.50
000.00
100.00
6.00
1.50
000.00
69.00
4.14
1.50
000.00
89.99
5.39
1.50
000.00
79.95
4.79
1.50
000.00
250.00
15.00
1.50
000.00
000.00
000.00
000.00
6.25
6.3.4 INDIVIDUAL GUEST PHONE BILL
Printout includes the following information:
Date and time the bill was printed
Room number requested
Date and time phone call was initiated
Number dialed
Duration of call
Charge of call
Total charge for all calls
Displays all call information since check in
Automatically applies phone credits to the bill
Phone bills are printed out on a per room basis
Phone bill information may be:
–
Printed and saved in memory
–
Printed and cleared from memory
55 LINES
By default, printout will print a header, followed by 50 lines per page
Printout size is adjustable through programming
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.26
PHONE BILL FROM [SUNSHINE SUITES ]
02/11/99
13:44
CHARGES BILLED TO ROOM NUMBER: 211
ROOM
DATE
TIME
ITEM
DESCRIPTION
DETAILS
211
211
211
211
211
02/10
02/10
02/11
02/11
02/11
15:30
20:44
06:34
13:15
13:40
TEL
TEL
TEL
TEL
TEL
3055922900
18008764782
18008764782
3055922900
3055922900
01:01:00
00:01:45
00:02:00
00:02:16
00:02:31
TOTAL
Sunshine
CHARGE
.35
.25
.25
.45
.55
1.85
Suites
6.27
] 01/02/95 17:12
Time Call Made
or Received
Hrs:Mins:Secs
Date Call Made
or Received
Month:Day
C.O. Line No.
2–4 Digits
Authorization
Code
4 Digits
Extension
2–4 Digits
Tenant
1 Digit
Call Type Flag
2 Characters
Call Duration
Hrs:Mins:Secs
Telephone No. Dialed
1–18 Digits
A
0
I
DI
DO
FO
Caller ID Name
1–15 Characters
TT
OT
IT
FI
DE
T
DISA call with error
Transferred call that was
terminated
Incoming transfer
Incoming call forwarded to
an external number
Outgoing transfer - Outgoing call
made and transferred
Caller received a transferred
call and transferred it again
Call Type Flag Definitions
Caller ID Number
1–15 Digits
Outgoing Call
Incoming Call
DISA call in
DISA call out
Outgoing record of
forwarded call
Abandoned call
Call Cost
6 Digits
================================================================================================================
CID/ANI NUMBER
CALL COST
T EXT AUTH TRK MM/DD STT.TIME DURATION FG DIALED DIGIT
CID/ANI NAME
================================================================================================================
SAMSUNG TELECOM
701 01/02 17:15:13 00:00:28 IT
13054264100
1 201
SAMSUNG TELECOM
13054264100
1 205
701 01/02 17:15:41 00:00:02 T
13055557890
CURTIS SMITH
702 01/02 17:24:49 00:00:25 IT
1 217
SUSAN HOLLINS
13055552354
1 202
702 01/02 17:25:14 00:00:03 T
$000.00
1 202
702 01/02 17:25:56 00:00:00 O 4264100
13054264385
SAMSUNG TELECOM
702 01/02 17:26:35 00:00:11 IT
1 217
SAMSUNG TELECOM
13054264385
1 203
702 01/02 17:26:46 00:00:16 T
$001.00
702 01/02 17:27:13 00:00:20 O 4264385
1 203
702 01/02 17:28:04 00:00:00 O 4264385
$000.00
1 203
JOAN LEVIN
13055559748
1 201
701 01/02 17:28:34 00:00:04 IT
13055558703
LENNY WILKINS
701 01/02 17:28:38 00:00:14 T
1 203
702 01/02 17:29:54 00:01:27 OT 5556420
$001.75
1 203
13055556420
PIZZA DELIVERY
1 205
702 01/02 17:31:06 00:03:00 TT
13055556420
PIZZA DELIVERY
702 01/02 17:33:24 00:02:18 T
1 209
TERRY PRUITT
13055553426
1
701 01/02 17:41:45 00:00:30 A
13055554676
BLANCHE MARKER
1
701 01/02 17:42:15 00:00:02 A
702 01/03 17:51:17 00:00:22 O 5555069
$001.00
1 203
ALEX DAULTON
13055556733
1
701 01/03 17:56:02 00:00:05 A
SMDR REPORT FOR [H/M Sample
6.3.5 ALL GUEST PHONE BILL (SMDR)
6.28
6.3.6 INDIVIDUAL WAKEUP ACTIVITY REPORT
Printout includes the following information:
Date and time the report was printed
Room number requested
Time wake up activity performed
Item code for activity performed
Description of activity performed
Details column
–
Time wake up call is set for
Charges for wake up related service
W/UP SET
The time a wake up call is set for
W/UP ANS
Wake up call answered
W/UP N/ANS
Wake up call not answered
W/U CANCEL
Wake up call cancelled
55 LINES
ACTIVITY TYPES:
Displays all wake up call activity since room was checked in
Wake up activity report print on a per room basis
By default, printout will print a header, followed by 50 lines per page
Printout size is adjustable through programming
EQUIPMENT REQUIRED
PC
PRINTER
iDCS DISPLAY
KEYPHONE
OFFICESERV 500 SYSTEM
*HOTEL LETTERHEAD IS CUSTOMER PROVIDED. DOTTED OUTLINE INDICATES DEFAULT PRINTOUT SIZE.
CUSTOMER
PROVIDED
SERIAL PRINTER
6.29
WAKE UP ACTIVITY FROM [SUNSHINE SUITES ]
01/22/98
14:35
CHARGES BILLED TO ROOM NUMBER: 213
ROOM
DATE
TIME
ITEM
DESCRIPTION
213
213
213
213
213
01/23
01/23
01/24
01/25
01/25
12:22
12:25
11:51
05:30
05:31
89
92
89
91
90
W/UP
W/UP
W/UP
W/UP
W/UP
DETAILS
SET
CANCL
SET
N/ANS
ANS
05:30
05:30
TOTAL
Sunshine
CHARGE
000.00
000.00
000.00
000.00
000.00
000.00
Suites
6.30
SAMSUNG TELECOMMUNICATIONS AMERICA
KEY SYSTEMS LIMITED WARRANTY
SAMSUNG TELECOMMUNICATIONS AMERICA (“STA”), warrants to its authorized Dealers and to the original retail purchaser (“Users”) of a STA product for a period of 24 months from the date of shipment of
the Product from STA’s facility, that the Product (except for lamps, fuses, and other consumable items)
will be free from defects in material and workmanship. Repaired or replaced materials shall be warranted for the balance of the warranty remaining on the original equipment, or 90 days from date of shipment from STA’s facility, whichever is longer.
This warranty is for the benefit of and shall apply only to authorized Dealers and to Users. This warranty
will not apply if the defect arises out of accident, neglect, alteration or misuse, failure of electric power,
air conditioning, humidity control, causes other than ordinary use, or causes beyond STA’s control. All
warranty claims shall be waived unless reported, in writing, to STA or its authorized Dealer, prior to the
expiration of the applicable warranty period.
The obligation of STA under this warranty is, at the sole option of STA: 1) the repair or replacement (with
new or refurbished parts), of the defective or missing parts that are causing the malfunction and which
are determined to be the defective by STA, and the return shipment of such parts to the Dealer (Dealer
or User shall be responsible to pay for shipment of the defective parts to STA and for all the expenses
connected with their removal and reinstallation); or 2) in lieu of repair or replacement, STA may refund
the price charged by STA to its Dealer for such parts as are determined by STA to be defective and which
are returned to STA through an authorized Dealer within the warranty period and no later than 30 days
after such malfunction, whichever occurs first.
To obtain service under this warranty:
(1) USERS must provide written notice of the malfunction to an authorized STA Dealer within the warranty period and not later than 30 days after the date of the malfunction, whichever occurs first. If the
USER is unable to identify an authorized STA Dealer, USER must provide written notice of the malfunction, including proof of the date of purchase of the equipment and the serial number of the malfunctioning Product, to STA at its corporate offices. Upon receipt of such notice and determination by STA
that User is eligible for Warranty service, STA will provide the USER with the name of an authorized STA
Dealer to contact for warranty service DEALERS must provide written notice of malfunction to STA no
later than the expiration of the warranty period 30 days after the date the Dealer becomes aware of the
malfunction, whichever comes first. For purposes of this Warranty, the issuance by STA of a Material
Return Authorization (MRA) number by telephone to an authorized Dealer shall be deemed to be written notice from the Dealer with respect to the material returned under that MRA.
STA MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, AND SPECIALLY DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THESE WARRANTIES ARE
DEALER’S AND USER’S SOLE REMEDIES AND IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE PART
OF STA FOR DAMAGES, INCLUDING, BUT NOT LIMITED TO, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OF THE PRODUCTS, OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, ARISING OUT OF OR IN CONNECTION
WITH THE PERFORMANCE OF THE PRODUCTS, WHETHER IN A CONTRACT OR TORT ACTION. INCLUDING
NEGLIGENCE, EVEN IF STA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES,THE TOTAL MAXIMUM LIABILITY OF STA FOR BREACH OF WARRANTY SHALL BE LIMITED TO A REFUND OF THE COST OF
THE DEFECTIVE PRODUCT.
No Dealer and no person other than an officer of SAMSUNG TELECOMMUNICATIONS AMERICA may
extend or modify this warranty, and no modification or extension of this warranty shall be effective
unless in writing signed by the authorized officer of SAMSUNG TELECOMMUNICATIONS AMERICA.
N O T E S
Download PDF