User manual | BLUE POWER World quality leader in independent electric power

BLUE POWER
World quality leader in independent electric power
About Victron Energy
With over 30 years’ experience, Victron Energy enjoys an unrivalled reputation for technical innovation, reliability and
quality, and is a world leader in the supply of self-supporting electric power. Our products have been designed to meet
the most demanding situations faced by a diversity of craft, recreational and commercial alike, whilst we also cater
for many other industrial and commercial applications. Our product range includes sine wave inverters and inverter/
chargers, battery chargers, DC/DC converters, transfer switches, Gel and AGM batteries, alternators, battery monitors,
complete network solutions and many other innovative solutions.
[ Products range ]
[ Applications ]
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Sinewave Inverters
Combined Inverter/chargers
Automatic Battery Chargers
DC DC Converters
Transfer Switches
Deep Cycle Gel and AGM batteries
High Power Alternators
Battery Monitors
DC Distribution Units
Control and Distribution Panels
Battery Isolators
Shore Power Connection Kits
System Monitoring and Control
Solar Panels
Solar and wind power systems
Yachts and commercial vessels
Special vehicles such as live
broadcasting vehicles,
ambulances, service vans, trains,
caravans etc
Industrial
Telecom
Emergency power supply
Remote areas where there is no
continuous supply
phoenix inverter
230VAC/50HZ
[ 12V: 180-5000 VA ]
[ 24V: 180-5000 VA ]
[ 48V: 180-5000 VA ]
characteristics 230VAC/50HZ
•SinusMax - Superior engineering
True sine wave inverter with optimised efficiency but without compromise in performance.
Employing hybrid HF technology, the result is a top quality product with compact
dimensions, light in weight and capable of supplying power, problem-free, to any load.
•
Extra start-up power
A unique feature of the SinusMax technology is very high start-up power. Phoenix inverters,
however, are well suited to power up difficult loads such as refrigeration compressors,
electric motors and similar appliances.
• Virtually unlimited power thanks to parallel and 3-phase operation capability
Up to 10 units Phoenix 24/5000 can operate in parallel to achieve 50KVA power output.
Operation in 3-phase configuration is also possible.
•To transfer the load to another AC source: the automatic transfer switch
If an automatic transfer switch is required on models rated at 1200 VA or more, we re commend using the Phoenix Multiplus instead. The switch is included in these products
and the charger function of the Multi can be disabled. For our lower power models we
recommend the use of our Filax Automatic Transfer Switch. Computers and other electronic
equipment will continue to operate without disruption because both the Filax and the
Phoenix Multi feature a very short switchover times (less than 20 milliseconds).
•Computer interface
All models rated at 1200 VA or more have a RS-485 computer interface. Together with the
VEConfigure software, all parameters of the inverters can be customised. The inverters can
also be connected to VEnet, the power control network of Victron Energy.
ACCESSORIES
BMV-600-S
Battery Monitor
Phoenix 12 Volt
inverter 14 Volt
48 Volt
12/180
24/180
12/350
24/350
48/350
12/750
24/750
48/750
C12/1200
C24/1200
C12/1600
C24/1600
C12/2000
C24/2000
12/3000
24/3000
48/3000
24/5000
48/5000
Input voltage range (VCD)
10.5 - 15.5
21.0 - 31.0
42.0 - 62.0
10.5 - 15.5
21.0 - 31.0
42.0 - 62.0
10.5 - 15.5
21.0 - 31.0
42.0 - 62.0
9.5 - 16
19.5 - 32.2
9.5 - 16
19.5 - 33
9.5 - 16
19.5 - 33
9.5 - 16
19.5 - 33
38 - 66
9.5 - 16
19.5 - 33
38 - 66
2000 (3)
3000 (3)
5000 (3)
Cont. output power at 25 ˚C (VA)
180
350
750
1200 (3)
1600 (3)
Cont. power at 25 ˚C / 40 ˚C (W)
175 / 150
300 / 250
700 / 650
1000 / 900 (4)
1300 / 1200 (4) 1600 / 1450 (4) 2500 / 2000 (4) 4500 / 4000 (4)
Peak power (W)
(W)
200
500
1400
2400
2300
3000
4000
90 / 91 / 92
91 / 93 / 94
6000
10000
Max. Efficiency 12/24/48 V (%)
91 / 92 / 92
93 / 94
93 / 94
93 / 94
93 / 94 / 95
94 / 95
Zero-load power 12/24/48V (w)
2.2 / 3.0 / 4.0 3.0 / 3.5 / 4.0 12 / 12 / 12
8 / 11
8 / 11
10 / 10
15 / 15 / 16
25
Zero-load power in AES mode
n.a.
5/8
5/8
8/10
10/10/12
20/20
relay
relay
relay
relay x2
relay x2
a,b,d,c,d,f,g,h
a,b,d,c,d,f,g,h
a,b,d,c,d,f,g,h
a-h
a-h
n.a.
3/4/5
Muti purpose relay
driver or relay (2)
Protection (4)
a,b,d,h
Common Characteristics
Output: 230 V ± 2% /50/60 Hz ± 0,2% (switch selectable) Operating temperature range: -20 to +50˚C Humidity: max 95%
a,b,d,h
a,b,d,h
ENCLOSURE
Phoenix Inverter
Control (PIV)
Computer controlled
operation and
monitoring (Victron
Interface Mk2)
Material & Colour
Aluminium (blue RAL 5012)
Battery-connection
1)
230 V AC-connection
IEC-320 (IEC-320 plug included) or Schuko
1)
Screw conn. 1)
G-ST18i
1)
M8 bolts
M8 bolts
G-ST18i
Spring-clamp
Screw-clamp
4 M8 bolts
Protection category
IP20
IP20
IP20
IP21
IP21
IP21
IP21
IP21
Weight (kg)
2.7
3.5
2.7
10
10
12
18
30
Dimensions (hxwxd in mm)
72x132x200
72x155x237
72x180x295 375x214x110
375x214x110
520x255x125
362x258x218
444x328x240
√ (PIV)
√ (PIV)
√ (PIV)
√ (PIV)
√ (PIV)
Remote on-off switch
√
√
√
√
√
√
√
√
Automatic transfer switch
FILAX
FILAX
FILAX
Phoenix Multi
ACCESSORIES
Remote panel (RS485)
Quattro
STANDARDS
Battery Alarm An
excessively high
or low battery
voltage is indicated
by an audible and
visual alarm, and a
relay for remote
signalling.
Safety
EN 60950
Emission / Immunity
EN 55014-1 / EN55014-2
Automotive Directive
95/54/EC and 2004/104/EC
EN 60335-1
1) Battery cables of 1.5 meter
2) Multipurpose relay which can be set for general alarm, DC under voltage or genset starts signal function 3) Suitable for parallel and 3-phase
4) Protection
a. Output short circuit
b. Overload
c. Battery voltage too high
d. Battery voltage too low
e. Battery reverse polarity detection
f. 230 V AC on inverter output
g. Input voltage ripple too high
h. Temperature too high
phoenix inverter
120VAC/60HZ
[ 12V: 180-5000 VA ]
[ 24V: 180-5000 VA ]
characteristics 120VAC/60HZ
•SinusMax - Superior engineering
True sine wave inverter with optimised efficiency but without compromise in performance.
Employing hybrid HF technology, the result is a top quality product with compact
dimensions, light in weight and capable of supplying power, problem-free, to any load.
•
Extra start-up power
A unique feature of the SinusMax technology is very high start-up power. Phoenix inverters,
however, are well suited to power up difficult loads such as refrigeration compressors,
electric motors and similar appliances.
• Virtually unlimited power thanks to parallel and 3-phase operation capability
Up to 6 units Phoenix 24/3000 can operate in parallel to achieve 18KVA power output.
Operation in 3-phase configuration is also possible.
•To transfer the load to another AC source: the automatic transfer switch
If an automatic transfer switch is required on models rated at 1200 VA or more, we re commend using the Phoenix Multiplus instead. The switch is included in these products
and the charger function of the Multi can be disabled. For our lower power models we
recommend the use of our Filax Automatic Transfer Switch. Computers and other electronic
equipment will continue to operate without disruption because both the Filax and the
Phoenix Multi feature a very short switchover times (less than 20 milliseconds).
ACCESSORIES
BMV-600 S Battery Monitor
Phoenix 12 Volt
inverter 24 Volt
12/180
24/180
12/350
24/350
12/750
24/750
Input voltage range (VCD)
10.5 - 15.5 / 21.0 - 31.0
Cont. output power at 25 ˚C (VA)
Cont. power at 25 ˚C / 40 ˚C (W)
180
350
750
175 / 150
300 / 250
700 / 650
Peak power (W) (W)
350
700
1400
Max. Efficiency 12/24/48 V (%)
87 / 88
89 /89
91 / 93
Zero-load power 12/24/48V (w)
2.6 / 3.8
3.1 / 5.0
14 / 14
Zero-load power in AES mode
n.a.
Protection (5)
a-g
Common Characteristics
Output: Output: 120 V ± 2% / 60 Hz ± 0,2% (switch selectable)
Operating temperature range: 0 - 122 ˚F Humidity: max 95%
3/4/5
ENCLOSURE
Phoenix Inverter
Control (PIV)
Material & Colour
Aluminium (blue RAL 5012)
Battery-connection
1)
230 V AC-connection
NEMA5-15R
Protection category
Weight (kg)
Dimensions (hxwxd in mm)
1)
Screw conn.
IP20
IP20
IP20
2.7 / 5.4
3.5 / 7.7
2.7 / 5.4
72x132x200
72x155x237
72x180x295
Remote on-off switch
√
√
√
Automatic transfer switch
FILAX
FILAX
FILAX
EN 60950
EN 60950
EN 60950
ACCESSORIES
Remote panel (RS485)
STANDARDS
Computer controlled
operation and
monitoring (Victron
Interface Mk2)
Battery Alarm
An excessively high or
low battery voltage is
indicated by an audible
and visual alarm, and
a relay for remote signalling.
Safety
Emission / Imunnity
Automotive Directive
EN 55014-1 / EN55014-2
95/54/EC and 2004/104/EC
1) Battery cables of 1.5 meter
2) Relay driver: open Collector 66V 3) Multipurpose relay which can be set for general alarm, DC under voltage or genset starts signal function 4) Suitable for parallel and 3-phase
5) Protection
a. Output short circuit
b. Overload
c. Battery voltage too high
d. Battery voltage too low
e. Battery reverse polarity detection
f. 230 V AC on inverter output
g. Input voltage ripple too high
h. Temperature too high
Multiplus
230VAC/50HZ
[ 12V: 800-3000 VA ]
[ 24V: 800-8000 VA ]
[ 48V: 3000 - 10000 VA ]
ACCESSORIES
characteristics 230VAC/50HZ
•
Multi-functional, with intelligent mains and generator power management
The multi gets its name from the multiple functions it can perform. It is a powerful true sine wave inverter, a sophisticated
battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact
enclosure.
•
Uninterrupted AC power (UPS function)
In the event of a grid failure, or mains or generator power being disconnected, the inverter within the Multi is automatically
activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
•
PowerControl - Dealing with limited generator, shore side or grid power
With the Phoenix Multi Control Panel a maximum generator or shore current can be set. The Multi will then take account of
other AC loads and use whatever is extra for charging, this preventing the generator or mains supply from being
overloaded.
•
PowerAssist - Boosting the capacity of grid or generator power, an innovative feature of the MultiPlus
This feature takes the principle of PowerControl to a further dimension allowing the MultiPlus to supplement the capacity
of the alternative source. Where peak power is so often required only for a limited period, the Phoenix MultiPlus will make
sure that insufficient shore or generator power is immediately compensated for by power from the battery.
•
Four stage adaptive charger and dual bank battery charging
The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software that
fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods
of float charging. In addition to this, the Multi will charge a second battery using an independent trickle charge output
intended for a main engine or generator starter battery.
Multiplus 12V / 24V / 48V
C12/800/16
C24/800/35
PowerControl / PowerAssist
Yes / Yes
Transfer switch (A)
16
C12/1200/50 C12/1600/70
C24/1200/25 C24/1600/40
C12/2000/80
C24/2000/50
30
12/3000/120
24/3000/70
48/3000/35
24/5000/120
48/5000/70
24/8000
48/8000
48/10000
16 or 50
50
100
100
INVERTER
VEBus digitial panel
This is a remote control
and monitoring panel
for the Phoenix Multiplus
Input voltage range (VCD)
9,5 – 17 V
Output
230 V ± 2% /50 Hz ± 0,1%
19 – 33 V
38 – 66 V
Frequency: 50 Hz ± 0.1 %
Cont. output power at 25 ˚C (VA) (5)
800
1200
1600
2000
3000
5000
8000
10000
Cont. output power at 25/40 ˚C (W)
700 / 650
1000 / 950
1300 / 1200
1600 / 1450
2500 / 2000
4250 / 3350
7000 / 6300
9000 / 8000
Peak power (W)
1600
2400
3000
4000
6000
10.000
16000
20000
Maximum efficiency (%)
92 / 94
93 / 94
93 / 94 / 95
94 / 95
95 / 96
96
Zero-load power (W)
8 / 10
9 / 11
15 / 15 / 16
25 / 25
30 / 35
35
Zero-load power in AES Modus
5/8
7/9
10 / 10 / 12
20 / 20
25 / 30
30
Zero-load power in Search Modus
2/3
3/4
4/5/5
5/6
8 / 10
10
Yes (25A)
50
50
charger
Computer controlled
operation and
monitoring (Victron
Interface Mk2)
AC input
187-265 VAC, 45-55 HZ, Power factor:1
Charge voltage ‘absorption’ (V DC)
14,4 / 28,8 / 57,6
Charge voltage ‘float’ (V DC)
13,8 / 27,6 / 55,2
Storage mode (V DC)
13,2 / 26,4 / 52,8
Charge current starter battery (A)
4 (Only by the 12V and 24V)
Battery temperature sensor
Yes
General
Blue Power panel
VE.Net / VE.Bus panel
Auxiliary output (A) (5)
n.a.
Yes (10A)
Multi purpose relay driver or relay
relay driver (7)
relay
Protection (5)
a-g
VE.Bus communication port
For parallel and three phase operation, remote monitoring and system integration
General purpose com. port (7)
Common Characteristics
1x
3x relay
1x
3x
3x
41
45
Operating temp. range: -20 - 50 ˚C (fan assisted cooling)
Humidity (non condesing) : max 95%
enclosure
Victron Global Remote
Common Characteristics
Material & Colour: aluminum (blau RAL 5012)
Battery-connection
Battery cabels 1,5 m
Protection category: IP 21
230 V AC-connection
G-ST18i Stecker
Spring-clamp
Screw-clamp
Weight (kg)
10
12
18
30
Dimensions (hxwxd in mm)
375x214x110
520x255x125
362x258x218
444x328x240 470x350x280 470x350x280
M8 Studs
STANDARDS
Safety
EN 60335-1,
EN60335-2-29
Emission / Immunity
EN55014-1,
EN 61000-3-2 / EN 55014-2,
Automotive Directive
95/54/EC and 2004/104/EC
1) Can be adjusted to 60 HZ;
120 V 60 Hz on, request
2) Protection key:
a) output short circuit
b) overload
c) battery voltage too high
d) battery voltage too low
e) temperature too high
f) 230 VAC on inverter output
g) input voltage ripple too high
3) Non linear load, crest factor 3:1
4) At 25 °C ambient
EN 61000-3-3
5) Switches off when no external AC
source available, Available on
3kVA models with 50A transfer
switch only
6) Programmable relay that can a. o.
be set for general alarm,
DC undervoltage or genset start
/stop function, AC rating: 230V/4A
DC rating: 4A up to 35VDC, 1A up
to 60VDC
7) Open collector output 66V 40mA
Quattro
230VAC/50HZ
[ 12V: 3000 VA ]
[ 24V: 3000 VA ]
[ 12V: 5000 VA ]
[ 24V: 5000 VA ]
[ 48V: 5000 VA ]
[ 24V: 8000 VA ]
[ 48V: 8000 VA ]
[ 48V: 10000 VA ]
characteristics 230VAC/50HZ
•Two AC inputs with integrated transfer switch
•Two AC outputs
The main output has no-break functionality. The second output is live only when AC is available on
one of the inputs of the Quattro.
• Virtually unlimited power thanks to parallel operation
Up to 6 Quattro’s can operate in parallel.
•Three phase capability
Three units can be configured for three-phase output.
• PowerControl - Dealing with limited generator, shore-side or grid power
• PowerAssist - Boosting shore or generator power
•Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid connected PV and other alternative
energy systems.
• A grid connected PV system will shut down when the grid fails! Not anymore with a
Quattro and batteries
Quattro
12/3000/120
24/3000/70
12/5000/200
24/5000/120
48/5000/70
PowerControl / PowerAssist
Yes / Yes
Integrated Transfer switch
Input voltage range: 187-265 VAC
Maximum feed through current (A)
50/30
24/8000
48/8000
Input frequency: 45-55 Hz
30/30 / 50/30
48/10000
Power factor: 1
2x100
2x100
inverter
Input voltage range (V DC)
Output (1)
9.5-17 / 19-33
9.5-17 / 19-33 / 38 66
19-33 / 38-66
38-66
Output voltage: 230 VAC ± 2%
Cont. output power at 25 ˚C (VA) (2) 3000
5000
8000
10000
Cont. output power at 25 ˚C (W)
2500
4250
7000
9000
Cont. output power at 40 ˚C (W)
2000
3350
6300
8000
Peak power (W)
6000
7500 / 7800
16000
20000
Maximum efficiency (%)
92 / 94
94 / 95
95 / 96
96
Zero-load power (W)
15
30
30 / 35
35
Load shedding output
0 / 25
10 / Switches off when no external AC source available
Charge voltage ‘absorption’ (V DC)
14.4 / 28.8
14.4 / 28.8 / 57.6
28.8 / 57.6
57.6
Charge voltage ‘float’ (V DC)
13.8 / 27.6
13.8 / 27.6 / 55.2
27.6 / 55.2
55.2
Storage mode (V DC)
13.2 / 26.4
13.2 / 26.4 / 52.8
26.4 / 52.8
52.8
Charge current house battery (A)
120 / 70
200 / 120 / 70
200 / 110
140
Charge current starter battery (A)
4 (12V and 24V models only)
Battery temperature sensor
Yes
charger
general
Multi purpose relay (1)
1x
3x / 1x / 1x
3x
3x
General purpose com. port (7)
1x
2x / 1x / 1x
2x
2x
Common Characteristics (3)
Operating temp.: -20 to +50 ˚C (fan assisted cooling) Humidity (non condensing) : max 95% / a-f
enclosure
Common Characteristics
Material & Colour: aluminium (blue RAL 5012)
Battery-connection
Four M8 bolts (2 plus and 2 minus connections)
Protection category: IP 21
230 V AC-connection
Screw clamp 13 mm² (AWG 6)
Weight (kg)
19
30
41
Dimensions (hxwxd in mm)
362x258x218
444x328x240
470 x 350 x 280
45
standards
Safety
EN 60335-1, EN 60335-2-29
Emissions / immunity
EN 55014-1, EN 61000-3-2 / EN 55014-2, EN61000-3-3
Automotive Directive
2004/104/EC
1) Multipurpose relay which can be set for general alarm, DC under voltage or genset starts signal function 2) Suitable for parallel and 3-phase
3) Protection
a. Output short circuit
b. Overload
c. Battery voltage too high
d. Battery voltage too low
e. Battery reverse polarity detection
f. 230 V AC on inverter output
g. Input voltage ripple too high
h. Temperature too high
phoenix Multiplus/quattro
120VAC/60HZ
[ 12V: 2000-5000 VA ]
[ 24V: 2000-5000 VA ]
characteristics 120VAC/60HZ
•
Multi-functional, with intelligent shore and generator power management
The multi gets its name from the multiple functions it can perform. It is a powerful true sine wave inverter, a sophisticated
battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact
enclosure.
•
Uninterrupted AC power (UPS function)
In the event of a grid failure, or mains or generator power being disconnected, the inverter within the Multi is automatically
activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that
computers and other electronic equipment will continue to operate without disruption.
• Virtually unlimited power thanks to parallel operation and three phase capability
Up to 6 Multi’s can operate in parallel to achieve higher power output. Three units of the same model can be configured for
three-phase output.
Input 1
120Vac
L1-1
120Vac
L2-1
Output
N1
L1 ( no break)
GND
120Vac
120Vac
L2
N
Input 2
120Vac
120Vac
•
PowerControl - Dealing with limited generator or grid power
With the Phoenix Multi Control Panel a maximum generator or shore current can be set. The Multi will then take account of
other AC loads and use whatever is extra for charging, this preventing the generator or shore supply from being
overloaded.
•
PowerAssist - Boosting the capacity of shore or generator power, an innovative feature of the MultiPlus
This feature takes the principle of PowerControl to a further dimension allowing the MultiPlus to supplement the capacity
of the alternative source. Where peak power is so often required only for a limited period, the Phoenix MultiPlus/Quattro will make
sure that insufficient shore or generator power is immediately compensated for by power from the battery.
•
Four stage adaptive charger and dual bank battery charging
The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software that
fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods
of float charging. In addition to this, the Multi will charge a second battery using an independent trickle charge output
intended for a main engine or generator starter battery.
Multiplus
12V / 24V
C 12/2000/80-30 120V
PowerControl
Yes
PowerAssist
Yes
Transfer switch (A)
30 A
N2
GND
50 A
60 A
9.5-17V
Output
L2-2
Quattro 24/5000/120 - 2x60
120/240V
inverter
Input voltage range (V DC)
GND
L1-2
12/3000/120-50 120V
24/3000/70-50 120V
19-33V
Output voltage: 120 VAC ± 2%
Frequency: 60 Hz ± 0,1%
Cont. output power at 25 ˚C (VA) (2)
2000
3000
5000
Cont. output power at 25/40 ˚C (W)
1600/1450
2500/2000
4250/3350
Peak power (w)
4100
6000
7500
Maximum efficiency (%)
93/94
93/94
94
Zero-load power (W)
10/10
15/15
30
charger
AC input
120V or 120/240V Input voltage range: 95-140 VAC Input frequency: 45 65 Hz Power factor:1
Charge voltage ‘absorption’ (V DC)
120VAC split-phase version
14.4/28.8
Charge voltage ‘float’ (V DC)
13.8/27.6
Storage mode (V DC)
13.2/26.4
Charge current house battery (A)
80/50
120/70
Charge current starter battery (A)
Input 1
230Vac
Battery temperature sensor
L1-1
Yes
general
Output
N1
Multi purpose relay driver or relay (1)
L1 ( no break)
GND
230Vac
Input 2
N
GND
L1-2
N2
GND
Relay
Protection (3)
Common characteristics
230Vac
120
4
a-h
Operating temp. range: 0-120 ˚F (fan assisted cooling)
Humidity (non condensing): max 95%
enclosure
Common Characteristics
Material & Colour: aluminum (blue RAL 5012)
Battery-connection
M8 Studs
Protection category: IP 21
230 V AC-connection
Spring-clamp
Protection category
IP 21
Weight (kg)
13
18
30
Dimensions (hxwxd in mm)
520x255x120
362x258x218
444x328x240
Four M8 Blots (2+, 2-)
Screw-clamp
standards
Safety
230 VAC single-phase version
EN 60335-1, EN 60335-2-29
Emission / Immunity
EN 55014-1, EN 55014-2/EN61000-3-2, EN 61000-3-3
Automotive Directive
95/54/EC abd 2004/104/EC
1) Multipurpose relay which can be set for general alarm, DC under voltage or genset starts signal function 2) Suitable for parallel and 3-phase
3) Protection
a. Output short circuit
b. Overload
c. Battery voltage too high
d. Battery voltage too low
e. Battery reverse polarity detection
f. 230 V AC on inverter output
g. Input voltage ripple too high
h. Temperature too high
blue power battery charger ip20
[ 12V: 7-15 A ]
[ 24V: 5-8 A ]
characteristics
• Universal input: 90-265 VAC or 90-350 VDC
The charger will operate on whatever supply is available.
•
Adaptive 4-stage charge characteristics: bulk - absorption - float - storage
The Blue Power charger features a microprocessor controlled ‘adaptive’ battery management.
The ‘adaptive’ feature will automatically optimise the charging process relative to the way the
battery is being used.
•
Less maintenance and aging when the battery is not in use: the Storage Mode
The storage mode kicks in whenever the battery has not been subjected to discharge during
24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (13,2 V for a 12 V battery) to
minimise gassing and corrosion of the positive plates. Once a week the voltage is raised back to the
absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and
sulphation, a major cause of early battery failure.
• Protected against overheating and silent fan cooling
Output current will reduce as temperature increases up to 60˚C but the Blue Power charger will not
fail. The load and temperature controlled fan is practically inaudible.
•Two LED’s for status indication
Yellow LED: bulk charge (blinking fast), absorption (blinking slow). float (solid)
Green LED: power on
24/5
24/8
Blue power charger IP 20
12/7
12/10
12/15
Input voltage range
90-265 VAC, 90-350 VDC
Frequency
45-65 or DC
Charge voltage ‘absorption’ (V DC)
14.4
28.8
Charge voltage ‘float’ (V DC)
14
28
Charge voltage ‘storage’ (V DC)
13.2
26.4
Charge current (A)
7/10/15
5/8
Charge characteristic
4-stage adaptive
Minimum battery capacity (Ah)
24/36/55
Can be used as power supply
Yes
Protection
Battery reverse polarity (fuse in battery cable)
Output short circuit, over temperature
Operating range
-20 tot 60 °C
16/24
Humidity: Max 95%
enclosure
Material & Colour
Aluminium (blue RAL 5012)
Battery-connection
Black and red cable of 1,5 meter
230 V AC-connection
Cable of 1,5 meter with Europe class 1 plug (CE certified)
Protection category
IP20
Weight (kg)
1.3
Dimensions (hxwxd in mm)
50x85x200
standards
Safety
EN60335-1, EN60335-2-29
Emission
EN55014-1, EN61000-3-2
Immunity
EN55014-2, EN61000-3-3
blue power battery charger IP65
[ 12V: 7-17 A ]
[ 24V: 3-12 A ]
characteristics
•Completely encapsulated: waterproof, shockproof and ignition protected
Water, oil or dirt will not damage the Blue Power charger. The casing is made of cast aluminium and the
electronics are molded in resin.
• Protected against overheating
Can be used in a hot environment such as a machine room. Output current will reduce as temperature increases
up to 60°C, but the Blue Power charger will not fail.
•
Automatic three stage charging
Once the absorption voltage has been reached to a low break point current (see specifications), or after a 20 hour
absorption period. The battery is therefore effectively protected against overcharging and can remain
permanently connected to the charger. The charger will automatically reset and start a new charge cycle after
interruption of the AC supply.
•Two LED’s for status indication
Yellow LED: battery being charged
Green LED: float charge, the battery is charged
Blue Power charger
12/7
12/17
Input voltage range (V AC) (1)
24/3
24/12
200-265
Frequency (Hz)
45-65
Charge voltage ‘absorption’ (V DC)
14.4
Charge voltage ‘float’ (V DC)
13.7
28.8
Charge current (A)
7
Charge characteristic
3 stage with max. 20 hours absorption time
Minimum battery capacity (Ah)
15
Breakpoint current (A)
0.7
Can be used as power supply
Yes
Protection
Battery reverse polarity (fuse in battery cable) Output short circuit, over temperature
Operating range
-20 to 60 °C,
27.2
17
3
12
35
6
24
1.7
0.3
1.2
Humidity Max: 100%
enclosure
Material & Colour
Aluminium (blue RAL 5012)
Battery-connection
Black and red cable of 1,5 meter
230 V AC-connection
Cable of 1,5 meter with Europe class 1 plug (CE-certified)
Protection category
IP 65
Weight (kg)
1.1
1.4
1.1
1.4
Dimensions (hxwxd in mm)
43x80x155
47x99x193
43x80x155
47x99x193
standards
Safety
EN60335-1, EN 60335-2-29
Emission
EN55014-1, EN61000-3-2
Immunity
EN55014-2, EN61000-3-3
1) 120V / 60 Hz available
phoenix battery charger
[ 12V: 30-50 A ]
[ 24V: 16-25 A ]
characteristics
•
Adaptive 4-stage charge characteristic: bulk - absorption - float - storage
The Phoenix charger features a microprocessor controlled ‘adaptive’ battery management system that can be preset to suit
different types of batteries. The ‘adaptive’ feature will automatically optimise the process relative to the way the battery is
being used.
•The right-amount of charge: adaptive charge
When only shallow discharges occur (a yacht connected to shore power for example) the absorption time is kept short in order
to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure
that the battery is completely recharged.
•
Preventing damage due to excessive gassing: the BatterySafe mode (see fig1. below)
If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen,
the Phoenix charger will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once
the gassing voltage has been reached (see the charge curve between 14,4 V and 15,0 V in fig.1 below).
•
Less maintenance and aging when the battery is not in use: the Storage mode (see fig.1 below)
The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode
float voltage is reduced to 2,2 V/cell (13,2 V for 12 V battery) to minimise gassing and corrosion of the positive plates. Once a
week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the
electrolyte and sulphation, a major cause of early battery failure.
•To increase battery life: temperature compensation
Every Phoenix charger comes with a battery temperature sensor. When connected, charge voltage will automatically
decrease with increasing battery temperature.
• Battery voltage sense
In order to compensate for voltage loss due to cable resistance, Phoenix chargers are provided with a voltage sense facility so
that the battery always receives the correct charge voltage.
•Computer interface
Every Phoenix Charger is ready to communicate with a computer through its RS-485 data port. Together with our VEConfigure
software, all parameters of the chargers can be customised. The chargers can also be connected to VENet, or to other
computerised monitoring control systems.
Fig. 1
ACCESSORIES
Phoenix charger
12V/24V
12/30
24/16
12/50
24/25
Input voltage range
90-265 VAC, 90-400 VDC
Frequency (Hz)
45-65, PF:1
Charge voltage ‘absorption’ (V DC)
14.4 / 28.8
Charge voltage ‘float’ (V DC)
13.8 / 27.6
Storage mode (V DC)
13.2 / 26.4
Battery bank
3
Charge current house batt. (A)(2)
30/16
Charge current starter batt. (A)
4
Charge characteristics
4 stage adaptive
Battery capacity (Ah)
100-400
100-200
Temperature sensor
Yes
Can be used as power supply
Yes
Forced cooling
Yes
Protection (1)
a,b,c,d
Common characteristics
Temperature: -20 to 60 °C (0 - 140°F) Max humidity: 95%
50/25
200-800
100-400
enclosure
Battery Monitor
Phoenix Charger Control
Material & Colour
Aluminium (blue RAL 5012)
Battery-connection
M6 Studs
230 V AC-connection
Screw-clamp 4mm²
Protection category
IP21
Weight (kg)
3.8
Dimensions (hxwxd in mm)
350x200x108
standards
Computer controlled
operation and monitoring
(Victron interface Mk2b)
Battery Alarm
An excessively high or low
battery voltage is indicated
by an audible and visual
alarm.
Safety
EN60335-2-29
Emission
EN55014, EN61000-3-2, EN61000-3-3
Immunity
EN55014-2
Vibration
IEC68-2-6: 10-150Hz/1.0G
Automotive directive
95/54/EC
1) Protection
a. Output short circuit
c. Battery voltage too high
2) Up to 40 °C ambient
b. Battery reverse polarity detection
d. Temperature too high
skylla TG battery charger
[ 24V: 30-50-80-100 A ]
[ 48V: 25-50 A ]
characteristics
•
Perfect chargers for any type of battery
Charge voltage can be precisely adjusted to suit any sealed or unsealed battery system. In particular,
sealed maintenance free batteries must be charged correctly in order to ensure a long service life.
Over voltage will result in excessive gassing and venting of a sealed battery. The battery will dry out
and fail.
•Controlled charging
Every TG charger has a microprocessor, which accurately controls the charging in three steps. The
charging process takes place in accordance with the IUoUo characteristics and charges more rapidly
than other processes.
• Use of TG chargers as a power supply
As a result of the perfectly stabilized output voltage, a TG charger can be used as a power supply if
batteries or large buffer capacitors not available.
•Two outputs to charge 2 battery banks
The TG chargers feature 2 isolated outputs. The second output, limited to approximately 4 A and
with a slightly lower output voltage, is intended to top up a starter battery.
•To increase battery life: temperature compensation
Every Skylla TG charger comes with a battery temperature sensor. When connected, charge
voltage will automatically decrease with increasing battery temperature. This feature is especially
recommended for sealed batteries which otherwise might be overcharged and dry out due to
venting.
• Battery voltage sense
In order to compensate for voltage loss due to cable resistance, TG chargers are provided with
a voltage sense facility so that the battery always receives the correct charge voltage.
ACCESSORIES
24/50 TG
24/50 GMDSS
24/50 TG
3 phase
24/80 TG
Skylla
24V / 48V
24/30 TG
24/30 GMDSS
Input voltage
185-265VAC, 320-450VAC or 180-400VDC (3)
Frequency (Hz)
45-65
24/100 TG
24/100 TG
3 phase
48/25 TG
Charge voltage ‘absorption’ (VDC)
28.5
57
Charge voltage ‘float’ (VDC)
26.5
53
48/50 TG
Battery capacity (Ah)
150-300
250-500
400-800
500-1000
125-250
250-500
Charge current house batt. (A) (2)
30
50
75
100
25
50
Charge current starter batt. (A)
4
Charge characteristics
IUoUo
n.a.
Temperature sensor
√
Can be used as power supply
√
Potential free contacts
√
Protection (1)
a,b,c,d
Common characteristics
Temperature: -20 to 60 °C (0 - 140 °F) Max humidity: 95%
enclosure
Battery Monitor
Skylla Control
Material & Colour
Aluminium (blue RAL 5012)
Battery-connection
M8 Studs
230 V AC-connection
Screw-clamp 2,5 mm² (AWG 6)
Protection category
IP21
Weight (kg)
5.5/6
5.5/13
10
10/23
5.5
10
Dimensions (hxwxd in mm)
365x250x147
365x250x147
365x250x257
365x250x257
365x250x257
515x260x265
365x250x147
365x250x257
standards
GMDSS panel
Skylla TG GMDSS
Safety
EN60335-2-29
Emissions
EN55014, EN61000-3-2, EN61000-3-3
Immunity
EN55014-2
Automotive divective
95/54/EC
1) Protection
a. Output short circuit
b. Battery reverse polarity detection
c. Battery voltage too high
d. Temperature too high
2) Up to 40 °C ambient
Wide input voltage 90-265 VAC and GL approval model available
CENTAUR BATTERY CHARGER
[ 12V: 20-30-40-50-60-80-100-200 A ]
[ 24V: 16-30-40-60-80-100 A ]
characteristics
• Quality without compromise
Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of
adverse environments: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for
maximum corrosion resistance. Temperature sensors ensure that power components will always operate
within specified limits, if needed, by automatic reduction of output current under extreme environmental
conditions.
• Universal 90 to 265 Volt input voltage range
All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether
50 Hz or 60 Hz.
•Three outputs that each can supply the full output current
Three isolated outputs to simultaneously charge 3 battery banks. Each output is capable to supply the full
rated current.
•Three stage charging, with temperature compensation
The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour
timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used
to compensate the charge voltage with 2 mV/˚C (1mV/˚F) per cell.
Centaur Charger
Common
characteristics
12/20
12/30
24/16
12/40
12/50
Input voltage: 90 - 265 VAC or 90 - 400 VDC
12/60
24/30
12/80
24/40
12/100
24/60
Input frequency: 45 - 65 Hz
24/80
12/200
24/100
Power factor: 1
Charge voltage
14.3 / 28.5 (1)
‘absorption’ (VDC)
ACCESSORIES
Charge voltage
‘float’ (VDC)
13.5/27 (1)
Output banks
3
Recommended
battery capacity
(Ah)
80-200
Charge current
(A)(2)
20
Total output
ammeter
Yes
Charge
characteristics
IUoUo (Three stage charging)
Temperature
sensor
Internal, -2mV / °C (-1mV / °F) per cell
Forced Cooling
Yes, temperature and current controlled fan
120-300
45-150
160-400
30/16
40
200-500
50
240-600
120-300
320-800
160-400
400-1000
240-600
320-800
800-2000
400-1000
60/30
80/40
100/60
80
200/100
Ignition protected Yes
Protection
Output short circuit, over temperature
Operating range
Temperature: -20 to 60 °C (0 - 140 °F)
Humidity max: 95%
enclosure
Battery Monitor
1.
Battery Alarm
An excessively high or low
battery voltage is indicated
by an audible and visual alarm.
Fasten the separate mounting
plate (A) to the wall where you
want to place the battery charger,
and simply hook up the Centaur.
2. Secure the bottom of the backside
(B) to the wall.
Material & Colour
Aluminium (blue RAL5012)
AC-connection
Screw-clamp 4mm² (AWG 6)
Batteryconnection
IP21
Protection
category
M6 Studs
Weight kg (lbs)
3.8
5
12
16
Dimension
(hxwxd in mm)
355x215x110
426x239x135
505x255x130
505x255x230
M8 Studs
standards
Safety
EN 60335-2-29, UL 1236
Emission
EN 55014, EN61000-3-2, EN 61000-3-3
Immunity
EN 55014-2
1) Standard setting. Optium charge/float voltages for Flooded Lead-acid, Gel-Cell or AGM batteries selectable by dip switch.
2) Up to 40 °C (1oo °F) ambient. Output will reduce to approximately 80% of nominal at 50 °C (120 °F) and 60% of nominal at 60 °C (140 °F)
orion DC/DC converter
characteristics
Possibly the widest range on the
market!
An ever-increasing is being used on
vehicles and industrial systems.
Because most low-voltage equipment is designed for 12 Volts,
Victron Energy supplies DC/DC converters which deliver a stable 12 Volt
supply from a 24 Volt system.
These products are also distinguished by high efficiency, together
with absolute safety. An inferior
supply can cause irreparable damage to your 12 Volt system, but the
use of an Orion voltage converter
prevents problems of that type.
Next to converters from 24 V to 12 V,
a wide range of other models available.
Battery charger
The Orion 24/12-20 and 24/12-30
can also be used as a 13.8 Volt battery charger for a 12 Volt starter or
accessory battery in an otherwise 24
V system.
To charge a 24 V battery from a 12
V system the Orion 12/27,6-12 can
be used. The output voltage of this
model can be adjusted with a potentiometer.
A super wide input range buckboost regulator:
The Orion 7-35/12-3 is an isolated
converter with a very wide input
range, suitable for both 12 V and 24
V systems, and a fixed 12,6 V output.
Non isolated converters
Orion
24/12-5
Orion
24/12-8
Orion
24/12-12
Orion
24/12-20
Orion
24/12-30
Orion
24/12-60
Orion
12/24-7
Orion
12/24-10
Input voltage range (V)
18-35
18-35
20-35
20-35
20-35
20-35
9-18
9-18
Output voltage (V)
13.2
13.2
13.2
13.8
13.8
13.8
24
24
Max. output current (A)
5.5
8
12
20
30
60
7
10
Fan assisted cooling
(temp. Controlled)
no
no
no
no
yes
yes
no
no
Galvanic isolation
no
no
no
no
no
no
no
no
Off load current
<5mA
<5mA
<5mA
appr. 25mA
appr. 25mA
appr. 50mA
<15mA
<15mA
Temperature increase after
30 minutes at full load (°­C)
30
20
30
25
33
33
30
30
Weight (kg)
0.17
0.25
0.26
0.48
0.6
1.2
0.3
0.4
Dimensions (hxwxd in mm)
49x88x68
49x88x98
49x88x98
49x88x126
49x88x151
88x100x180
49x88x98
49x88x126
Note: two units orion 24/12-60 can be connected in parallel to obtain a 120A converter
Isolated converters
Orion xx/yy-100W
Orion xx/yy-200W
Orion xx/yy-360W
Power rating (W)
100 (12,5V/8A or 24V/4A)
200 (12,5V/16A or 24V/8A)
360 (12,5V/30A or 24V/15A)
Galvanic isolation
yes
yes
yes
Temperature increase after
30 minutes at full load (C)
25
30
30
Fan assisted cooling (temp. Controlled)
no
yes
yes
Weight (kg)
0.5
0.6
1.4
Dimensions (hxwxd in mm)
49 x 88 x 152
49 x 88 x 182
64 x 163 x 160
Input voltage (xx)
12 V (9-18V) or 24 V (20-35 V) or 48 V (30-60 V) or 96 V (60-120 V), 110 V
Output voltage (yy)
12,5 V or 24 V
Isolated 24V battery charger:
Orion 12/27,6-12
Input 9 - 18 V, output 27,6 V, current limit 12 A, fan assisted cooling
Output voltage adjustable with potentiometer
Weight 1,4 kg, dimensions 64 x 163 x 160 mm
Isolated buck-boost regulator:
Orion 7-35/12-3
Input 7 - 35 V, output 12,6 V current limit 3 A, derate current linearly from 3 A at 18 V to 1,5 A at 7 V
Weight 1,4 kg, dimensions 64 x 163 x 160 mm
Common characteristics
Output voltage stability
2 % (Orion 12/24-7 and Orion 12/24-10: + 0% / -5%)
Output voltage tolerance
3%
Output noise
< 50 mV rms
Off load current
< 25 mA (isolated converters)
Efficiency
Non isolated: appr. 92%
Isolation
> 400 Vrms between input, output and case (isolated products only)
Operating temperature
- 20 to + 30 °C. Derate linearly to 0 A at 70 °C
Humidity
Max 95% non condensing
Casework
Anodised aluminium
Connections
6.3 mm push-on flat blade connectors
Isolated: appr. 85%
protection
Overcurrent
Short circuit proof
Overheating
Reduction of output voltage
Reverse polarity conn
Fuse and reverse connected diode across input
Overvoltage
Varistor (also protects against load dump)
standards
Emission
EN 50081-1
Immunity
EN 50082-1
Automotive Directive
95/45/EC
BAttery isolator
ARGO DIODE BATTERY ISOLATORS
Diode battery isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory
battery for example will not result in also discharging the starter battery.
The Argo battery isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output
approximately 0,45 V.
All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensated for the voltage drop over the
diodes in the isolater.
Argo Battery Isolator
702SC
903SC
1202SC
1203SC
1602SC
1603SC
Maximum charge (A)
50
70
100
100
130
130
Maximum alternator
current (A)
70
90
120
120
160
160
Number of batteries
2
3
2
3
2
3
Connection
M6 Studs
M8 Studs
Connection
compensation diode
M4
Weight kg (lbs)
0,8 (1.8)
0,8 (1.8)
1,2 (2.6)
1,2 (2.6)
1,5 (3.3)
Dimensions H x B x L in mm
(H x B x L in mm)
60 x 120 x 80
60 x 120 x 150 60 x 120 x 100 60 x 120 x 150
(2.4 x 4.7 x 3.2) (2.4 x 4.7 x 6.0) (2.4 x 4.7 x 3.9) (2.4 x 4.7 x 6.0)
ARGO FET R
B+
B+
victron energy
1,2 (2.6)
Diode Battery Isolator
CE
60 x 120 x 200
(2.4 x 4.7 x 7.9)
Battery Isolators: no voltage loss
Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery
charger), without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery.
In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1
Volt at higher currents. The new Argofet isolators have a special current limited energize input that will power the B+ when the engine run/stop switch
is closed.
Argo FET Battery Isolator
Argofet 100-2
Argofet 100-3
Argofet 200-2
Argofet 200-3
Maximum charge (A)
100
100
200
200
Maximum alternator current (A)
100
100
200
200
Number of batteries
2
3
2
3
Connection
M8 Studs
Weight kg (lbs)
Weight kg (lbs)
Maße h x w x d in mm
(h x w x d in Zoll)
65 x 120 x 200
(2.6 x 4.7 x 7.9)
CYRIX microprocessor controlled battery combiner
No voltage loss
The Cyrix battery combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of the has
reached a preset voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that
one or more batteries are being discharged). Cyrix battery separators are an excellent replacement for diode isolators. The main feature is that there is
virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased.
Prioritising the starter battery
In a typical setup the alternator is directly connected to the starter battery. The accessory battery, and possibly also a bow thruster and other batteries
are each connected to the starter battery by Cyrix battery combiners. When a Cyrix senses that the starter battery has reached its connect voltage it will
engage, to allow for parallel charging of the other batteries.
Bidirectional voltage sensing
The Cyrix senses the voltage of both connected batteries. It will therefore also engage if for example the accessory battery is being charged by a battery
charger.
Parallel connection in case of emergency The Cyrix can also be engaged with a switch to connect batteries in parallel manually.
This is especially useful in case of emergency when the starter battery is discharged of damaged.
Cyrix Battery
combiner
Cyrix-i 12/24-100
Model
Cyrix-i 12/24-200
Cyrix-i 24/48-200
Cyrix-i 12/24-400
Cyrix-i 24/48-400
Continuous current (A)
100
Continuous current
200A
400A
Connect voltage (V)
From 13V to 13,8V and
26 to 27,6V with intelligent trend detection
Peak current
1000A during 1 Sec. 2000A during 1 Sec.
Input voltage 12/24V Model
Input voltage 24/48V Model
8-36VDC
16-72VDC
8-36VDC
16-72VDC
Connect/disconnect profiles
See table
See table
Over voltage disconnect
16V / 32 / 64V
16V / 32 / 64V
Disconnect voltage (V)
From 11V to 12,8V and
22 to 25,7V with intelligent trend detection
Current consumption when
open
<3 mA
Connection for remote on/off
Ja
Weight kg (lbs)
0,11 (0.24)
Dimensions h x w x d in mm
(h x w x d in Zoll)
46 x 46 x 80
(1.8 x 1.8 x 3.2)
Current consumption when open 4 mA
4 mA
Emergency start
Yes, 30s
Yes, 30s
Microswitch for remote monitoring
Yes
Yes
Status indication
Bicolour-LED
Weight kg (lbs)
0,9 (2.0)
Dimensions: h x w x d in mm
(h x w x d in Zoll)
78 x 102 x 110
(3.1 x 4.0 x 4.4)
Battery monitoring
characteristics
Precision monitoring
The essential function of a battery monitor is to calculate ampere-hours consumed and the state of charge of a battery.
Ampere-hours consumed is calculated by integrating the
current flowing in or out of the battery. In case of a constant
current, this integration is equivalent to current multiplied by
time. A discharge current of 10A during 2 hours, for example, amounts to 20Ah consumed. All our battery monitors are
based on a powerful microprocessor, programmed with the
algorithms needed for precision monitoring.
Standard information and alarms
Battery voltage (V)
Battery charge/discharge current (A)
Ampere-hours consumed (Ah)
State of charge (%)
Time to go at the current rate of discharge
Visual and audible alarm: over- and under voltage,
and/or battery discharged
Programmable alarm or generator start relay.
BMV 600-S: low cost ultra high resolution monitor
Highest resolution: 10mA (0,01A) with 500A shunt.
Lowest current consumption: 1mA.
Easiest to wire: the BMV 600 comes with stunt, 10 meter
RJ 12 UTP cable and 2 meter battery cable with fuse.
No other components needed.
Easiest to install: separate front bezel for square or round
appearance; ring for rear mounting and screws for front
mounting.
Broadest voltage range: 9-90 VDC without prescaler needed.
BMV 602-S: two batteries and communication port
In addition to all the features of the BMV600, the BMV602 can
measure the voltage of a second battery and has a communication port. (Isolated RS232 interface is needed tot connect
to a computer)
BMV 602-HS: 35 to 150VDC voltage range
No prescaler needed.
VE.Net Battery Controller: any number of batteries
One VE.Net panel will connect to any number of battery
controllers.
Comes with 500A/50mV shunt and can be programmed for
any other shunt.
With use, abuse and data memory.
Temperature sensor and connection kit included.
Battery Monitoring
BMV 600 - S
BMV 602 - S
BMV 602 - HS
VE.Net
Battery Controller
Power supply voltage range
9-90 VDC
9-90 VDC
35-150 VDC
9-60 VDC
Current draw, back light off
4mA at 12V
3mA at 24V
4mA at 12V
3mA at 24V
3mA
3mA at 48VDC
9-90 VDC
35-150 VDC
39-60 VDC
Input voltage range (VDC)
9-90 VDC
Battery capacity (Ah)
20-9999 Ah
Operating temperature range
-20 - 50 °C (0 - 120 °F)
20-60000Ah
Measures voltage of second battery
No
Yes
Yes
No
Communication port
No
Yes
Yes
Yes (VE.Net)
Potential free contacts
60V/1A (N/O)
resolution (with 500 A shunt)
Current
± 0.01A
Voltage
± 0.01V
Amp hours
± 0.1Ah
State of charge (0-100%)
± 0.1%
Time to go
± 1 min
Temperature (0-50 °C or 30-120 °F)
n.a.
Accuracy of current measurement
± 0.3%
Accuracy of voltage measurement
± 0.4%
± 0.1A
± 1 °C (± 1°F)
installation and dimensions
Installation
Flush mount
DIN rail
Front
63 mm diameter
22 x 75 mm (0.9 x 2.9 inch)
Front bezel
69 x 69 mm (2.7 x 2.7 inch)
n.a.
Body diameter
52 mm (2.0 inch)
n.a.
Body depth
31 mm (1.2 inch)
105 mm (4.1 inch)
Shunt (included)
500 A / 50 mV
500 A / 50 mV
Cables (included)
10 meter 6 core UTP with RJ12 connectors
and cable with fuse for ‘+’ connection
Supplied with 1m cables
Temperature sensor
n.a.
Computer interface
n.a.
accessories
Supplied with 3m cable
Optional
Optional
n.a.
VE NET
characteristics
•
VE NET stands for VICTRON ENERGY NETWORK, a low power network that will monitor all essential
equipment and alarms, and keep you informed through automatic e-mails, text messages, and even
voice calls. Similarly the wireless connection could be used to access all systems on board remotely. For the
ultimate in monitoring and control of your power system, VE.Net represents the state of the art. As a truly
integrated solution, VE.Net provides the following components:
• 1. Blue power panel - multi character display and interface panel
• 2. Battery Controller - full function battery monitoring module (any number can be connected to the network).
• 3. Generator control - full monitoring and control of your generator including auto start/stop functionality.
• 4. VRM module - enables full access to system status and control remotely through the internet. It also gives a
historical overview with graphs and bars trough our internet website.
VE.Net can also be integrated with any number of other devices including an on board PC, power distribution
systems and or senders and alarms. Your imagination is the only limit to what is possible.
Victron Global Remote
•
The Global Remote is a modem which sends alarms, warnings and system status reports to cellular phones via
text messages (SMS). It can also log data from Victron Battery Monitors, Multi’s, Quattro’s and Inverters to a website
through a GPRS connection. The usage of this website is free of charge.
The idea is simple: you can use it to get SMS alarms from a Multi, a Battery System, or both. When monitoring the
usage of batteries, it can be extremely helpful to receive under and overvoltage alarms; whenever they occur. For
this purpose, the Global Remote is perfect. A prepaid SIM-card (for example) in combination with the Global Remote
is adequate for remotely monitoring your system.
Taking it one step further, an internet browser and -connection is all you need to view all of the data online. You
can simply create an account on the website and add your modem(s). Subsequently you can configure the GPRS
connection, which will enable you to monitor the historic data of several basic properties such as system voltages,
power levels and status information. All of this data is graphed. These graphs are available in daily, weekly and
monthly timeframes.
Victron Remote Management is the name of the system which consists of the VGR and the monitoring website.
To get a preview: please go to http://www.victronenergy.com, and login at ‘Victron Remote Management’ via the
Login menu on the upper right of the page.
1x Y cable (16-way plug to male DB9
+ 12-way socket)
victron energy
B L U E
P O W E R
DB9 male
SIM
victron global remote
gender changer
null modem
MK2 interface
(included with VGR )
B L U E
P O W E R
+
-
RJ45 UTP
12/24Vdc
BMV-602
battery monitor
SETUP
victron energy
MK2.2a
VGR900100000
SELECT
RJ12 UTP Cable
AGM
12-200
others
Batteries
•
•
•
•
•
•
•
VRLA AGM: design life 7-10 years
VRLA GEL: design life 12 years
VRLA GEL 2 volt cells: design life 20 years
The AGM range has very low internal resistance making them particularly suitable
for high current discharge and charging.
The GEL model range offer best deep cycle durability and overall longer life.
The use of high purity materials and lead calcium grids ensure that for both AGM
and GEL products have particularly low self discharge so that they will not go flat
during long periods without charge.
Both ranges are supplied with M8 drilled, flat copper terminals ensuring best
possible connection contact and eliminating the need for battery terminals.
Manufactured under ISO 9002 quality standards, they are compliant with both CE
and UL specifications in ABS fireproof containers and come with Victron’s 2 year
world-wide warranty.
FILAX Transfer Switch
•
Filax: the ultra fast transfer switch
The Filax has been designed to switch sensitive loads, such as computers or
modern entertainment equipment from one AC source to another.
The priority source typically is the mains, a generator or shore power. The
alternate source typically is an inverter.
PowerMan Transfer Switches
•
Ideal to build a no-break power supply with several paralleled Multi’s.
The PowerMan transfer switch enables seamless power transfer from one or more
AC sources to several paralleled Multi’s. In-built AC current monitoring ensures
that the AC power management functionality of the Multi’s remains available.
BatteryProtect (Models: BP-40i, BP-60i, BP-200i)
• The BatteryProtect disconnects the battery from non-essential loads before it
is completely discharged (which would damage the battery) or before it has
insufficient power left to crank the engine.
ESP system panel
•
The new ESP panel system provides a contemporary designed range of panels
that cover the core engineering systems. The main system panel is the heart of
the range. This provides AC and DC monitoring, Multi control and backlight
control. Additional panels include AC and DC circuit breaker panels, a general
control panel, a VE Net panel.
multiplus principle
INVERTER/CHARGER SYSTEM WITH INTELLIGENT SHORE AND GENERATOR POWER MANAGEMENT
PowerControl: Dealing with limited generator or grid power All models in the MultiPlus range feature powerful battery chargers. When the largest model is working hard it can draw almost 10A from a 230V supply. Using the remote panel it is possible to ‘dial-in’ the maximum current that is available from mains or generator.
The MultiPlus will then automatically regulate the charger taking account of other system AC loads and ensuring the charger only uses what is spare. This way it is
possible to avoid tripping the mains power or overloading the generator.
Power control ©
Battery charger reduces its output, if required, to avoid overload of supply when system consumption is high.
Multi remote panel
MultiPlus
PHOENIX MULTI CONTROL
inverter on
mains on
overload
12
boost
low battery
AC distribution
20
24
28
4
float
on
16
8
equalize
temperature
0
charger only
30
Water Heater (10A)
shore current limiter
off
16A
mains on
inverter on
bulk
overload
absorption
low battery
float
temperature
Microwave (6A)
Fridge (1A)
phoenix
multi plus 12/3000/120
RCD
www.victronenergy.com
TV / DVD (1A)
Computer (1A)
Kettle (13A)
Public grid
Hairdryer (8A)
13A
Battery 12V/300Ahr
Services
Power Tools (2A)
Reduced charge to battery
PowerAssist: Boosting the power available from mains or generator, an innovative feature of Multiplus. The feature that most distinguishes the MultiPlus from other
inverter / chargers is PowerAssist. This feature takes the principle of PowerControl to a further dimension by allowing a MultiPlus to supplement the power available
from mains or generator to ‘assist’ during periods of high demand. Peak power demand is almost always sustained only for short periods, either a few minutes (in
the case of items like cooking appliances) or just a few seconds (in the case of the burst of energy needed to start an air-conditioning or refrigeration compressor).
With the capacity of the generator or mains power set on the remote panel, the MultiPlus detects when the load is becoming too much for the supply and will
instantly provide the extra power required. When the demand has reduced, the unit returns to charging the battery. This feature is equally effective in large and
small systems helping to reduce the required generator capacity or to achieve greater things with limited mains power. There is even a special feature to enable the
MultiPlus/Quattro to work perfectly with portable generators.
Power assist ©
Inverter boosts incoming power, if required, to avoid overload of supply when system consumption exceeds supply.
Multi remote panel
MultiPlus
PHOENIX MULTI CONTROL
inverter on
mains on
overload
boost
low battery
equalize
temperature
float
on
charger only
off
12
16
AC distribution
20
8
24
28
4
0
30
Water Heater (10A)
shore current limiter
16A
mains on
inverter on
bulk
overload
absorption
low battery
float
temperature
Microwave (6A)
Fridge (1A)
phoenix
multi plus 12/3000/120
RCD
www.victronenergy.com
TV / DVD (1A)
Computer (1A)
Public grid
Battery 12V/300Ahr
Services
Battery delivers energy to “Power Assist” incoming
Kettle (13A)
21A
power
Hairdryer (8A)
Power Tools (2A)
system application
Comfort system
Comfort plus system
Appliance
System
Appliance
System
Lighting
Quattro 12/3000/120
Lighting
2 xQuattro 24/5000/120
Communication & navigation
BMV602-S battery monitor
Communication & navigation
VE-NET Battery controller
Water heater
2x12V/200AH and 1X80AH batteries
Water heater
4x12V/200AH and 1X80AH batteries
Microwave oven
Digital control remote panel
Blue Power panel
2 ring introduction hob
Alternator 12/150
Electric gallery with 4 ring induction
hob, microwave/combi oven, refrigerator, freezer, washer/dryer.
Coffee machine/Kettle
DC Link Box
TV/DVD
Isolation transformer
Coffee machine and kettle
Alternator 12/150
TV/DVD
DC Link box
Multimedia PC
Isolation transformers
Laptop
Cyrix batttery separator
Smal chargers (mobile phone,
electric shaver)
Small chargers (mobile, phone, shaver etc)
Modest air-conditioning
Refrigerator and freezer
Comfort system - 7 kVa (30a) capacity
MARINE 7
Quattro
BMV-602 Battery Monitor
VEBus digital panel PHOENIX MULTI CONTROL
BMV-602
AC distribution
battery monitor
inverter on
mains on
overload
boost
low battery
equalize
temperature
float
on
SETUP
charger only
off
shore current limiter
+
-
SELECT
Water Heater (10A)
QUATTRO
12
Microwave (6A)
120
Fridge (1A)
TV / DVD (1A)
32A/30mA
RCD/RCBO
Shore
Power (16A)
Induction Hob
Only active with shore/genset Coffee Maker (8A)
Hairdryer (8A)
Power Tools (2A)
DC distribution
DC Link Box
Cabin Light
Water Pump
Genset
230V/50Hz
4kVA
Navigation Equip.
Bilge Pumps
Accessory 12V/400Ah
(2 x 12V 200Ahr)
Shower Pump
Comfort plus system - 25 kVa capacity
MARINE 7
Blue Power panel
2 x Quattro 24/5000/120 VE.NET
AC distribution
cancel
enter
Water Heater (10A)
QUATTRO
QUATTRO
24
24
5000
120
5000
Microwave (6A)
Fridge (1A)
120
TV / DVD (1A)
Shore
Power (32A)
32A/30mA
RCD/RCBO
Only active with shore/genset Computer (1A)
Coffee Maker (8A)
Hairdryer (8A)
Washer/dryer (13A)
Air - Con (Partial)
Induction Hob
DC distribution
DC Link Box
VE.NET
Battery
Controller
Cabin Light
Water Pump
Genset
230V/50Hz
15kVA
Navigation Equip.
Bilge Pumps
Accessory 24V/1000Ah
(12 x 2V 1000Ahr)
Shower Pump
BLUESOLAR POLYCRYSTALLINE PANELS
• Low voltage-temperature coefficient enhances high-temperature operation.
• Exceptional low-light performance and high sensitivity to light across the entire solar spectrum.
• 25-year limited warranty on power output and performance.
• 2-year Limited warranty on materials and workmanship.
• Sealed, waterproof, multi-functional junction box gives high level of safety.
• High performance bypass diodes minimize the power drop caused by shade.
• Advanced EVA (Ethylene Vinyl Acetate) encapsulation system with triple-layer back sheet meets the most
stringent safety requirements for high-voltage operation.
• A sturdy, anodized aluminum frame allows modules to be easily roof-mounted with a variety of standard
mounting systems.
• Highest quality, high-transmission tempered glass provides enhanced
stiffness and impact resistance.
PV-ST01 connectors
• Pre wired quick-connect system with PV-ST01 connectors.
BlueSolar Panel 130W
Electrical data under STC (1)
Module Size
Type
Glass size
Weight
Nominal
Power
Max-Power
Voltage
Max-Power
Current
Open-Circuit
Voltage
Short-circuit
Current
PMPP
VMPP
IMPP
Voc
Isc
Module
MM
MM
KG
BSP30-12
532x418x23
527x413
3
30
W
18
V
1.66
A
21.6
1.83
BSP50-12
810x534x35
804x528
6.5
50
18
2.78
21.6
3.05
BSP80-12
1196x534x35
1189x528
8
80
18
4.44
21.6
4.88
BSP130-12
1456x666x35
1450x660
13
130
18
7.23
21.6
7.94
BSP180-12
1580x808x35
1574x802
15
180
36
4.95
43.2
5.45
BSP280-12
1930x980x50
1924x974
19
280
36
7.78
43.2
8.55
Module
BSP30-12
BSP50-12
BSP80-12
BSP130-12
BSP130-12
BSP280-24
Nominal Power (±3% tolerance)
30W
50W
80W
130W
180W
280W
Monocrystalline
Monocrystalline
Monocrystalline
inverter
Cell type
Monocrystalline
Polycrystalline
Number of cells in series
36
72
Polycrystalline
Temperature coefficient of Isc (%)
+0.06/°C
+0.06/°C
+0.06/°C
+0.06/°C
+0.06/°C
+0.06/°C
Temperature coefficient of Voc (%)
-0.35/°C
-0.35/°C
-0.35/°C
-0.35/°C
-0.35/°C
-0.35/°C
Maximum system voltage (V)
1000V
Temperature coefficient of
-0.47/°C
-0.47/°C
-0.47/°C
-0.47/°C
-0.47/°C
-0.47/°C
Temperature coefficient of IMPP
+0.06/°C
+0.06/°C
+0.06/°C
+0.06/°C
+0.06/°C
+0.06/°C
Temperature coefficient of VMPP
-0.34/°C
-0.34/°C
-0.34/°C
-0.34/°C
-0.34/°C
-0.34/°C
Temperature Range -40°C to +80°C
-40°C to +80°C
Surface Maximum Load Capacity
200kg/m²
Allowable Hail Load Steel ball
Steel ball (weight 227g, diameter 25mm) fall down from 1m height
Junction Box Type PV-RH0301
PV-RH0301
Connector Type
PV-ST01/M PV-ST01/F
Length of Cables 900mm
900mm
Output tolerance +/-3%
+/-3%
Frame
Aluminium
Product warranty
2 years
Warranty on electrical performance
10 years 90% + 15 years 80% of power output
Smallest packaging unit
Quantity per pallet
2 panels
88 panels
44 panels
1) STC (Standard Test Conditions): 1000W/m2, 25ºC, AM (Air Mass) 1.5
PV-ST01 connectors
44 panels
40 panels
52 panels
36 panels
V
A
PHOENIX MULTICOMPACT
MARINE 5
PHOENIX MULTI COMPACT WIND EN SOLAR
BMV-602
battery monitor
SETUP
+
-­
SELECT
mains
charger
failure
AC distribution
Inverter 24/8000
WIND CONVERTER
POWER
CHG.MODE
Bat. Select
LOAD
-­ +
BATTERY PV
-­ +
-­ +
AC Solar system
Blue Power panel
PV system
2 x Quattro 48/10000/140
VE.NET
cancel
enter
QUATTRO
QUATTRO
48 10000 140
48 10000
140
AC distribution
Grid inverter
VE Solar Switch
Water Heater (10A)
Microwave (6A)
Fridge (1A)
TV / DVD (1A)
Public grid
32A/30mA
RCD/RCBO
Computer (1A)
Coffee Maker (8A)
Hairdryer (8A)
Washer/dryer (13A)
VE.NET
Battery
Controller
Genset
230V/50Hz
DC Link Box
Air - Con (Partial)
Induction Hob
WIND EN SOLAR SOLUTIONS
When the public grid is available, the Victron SolarSwitch will connect the solar inverter directly to the grid.
If the grid fails, the power from the solar inverter will be redirected to the output of the MultiPlus. The MultiPlus replaces the grid and will
balance the power mismatch between the load and the solar inverter. A power shortage will be supplemented by the MultiPlus, discharging the battery, and excess power will be used to recharge the battery.
Once the batteries are fully charged, the excess power can be redirected to a water heater (relay not shown), or a dump load (not shown),
or the grid inverter can be stopped by slightly changing the output frequency of the MultiPlus (this is a standard feature of the MultiPlus).
In order to prevent the batteries from discharging completely in case of insufficient solar power, some or all loads can be can be shut
down with programmable relays available on the SolarSwitch (not shown).
Specifications of the SolarSwitch
SolarSwitch
AC inputs (Mains, MultiPlus/Quattro and Solar)
Input voltage range: 187-265 VAC
Maximum switch through current (A)
25A
Maximum power consumption (W)
< 4W
Input frequency: 45 – 65 Hz
GENERAL
Auxiliary programmable Relay (3X) (1)
Max load: 8A 250VAC
Status LED
1 Blue / 1 Yellow / 1 Red
Common Characteristics
Operating temp.: -20 to +50°C
Humidity (non condensing) : max 95%
ENCLOSURE
Common Characteristics
Material & Colour: Housing polyamide 6.6 / green
Cover unbreakable polycarbonate / Transparent
Protection: IP 20
230 V AC-connection
Screw terminals 5.2mm² (10 AWG)
Auxiliary relay connection
Screw terminals 2.5mm² (19 AWG)
Weight (grams)
750
Dimensions (hxwxd in mm)
88 x 215 x 110
STANDARDS
Safety
EN 60335-1, EN 60335-2-29
Emission / Immunity
EN55014-1, EN 55014-2, EN 61000-3-3
1) Three programmable relays
AC rating: 230V/4A
Can be programmed with VEConfigure
Application examples: Alarm, generator start or load shedding function
DC rating: 4A up to 35VDC, 1A up to 60VDC
No-break back-up for grid connected solar system
Grid inverter
1.Alarm
2.Genset start
3.Load shedding
Solar panel
1.
2.
3.
programmable relays
solar
SolarSwitch
mains
multi
VE.BUS
Protected loads
Public grid
Unprotected loads
water heater
BlueSolar charge controllers
BlueSolar 12/24-10
10A at 12V or 24V
- Low cost PWM controller.
-Internal temperature sensor.
-Three stage battery charging (bulk, absorption, float).
- Protected against over current.
- Protected against short circuit.
- Protected against reverse polarity connection of the solar panels and/or battery.
- With low voltage load disconnect output.
BlueSolar 12/24-10
BlueSolar
12/24-20
PowerDUO
control
©
BlueSolar DUO 12/24-20
20A at 12V or 24V
- PWM controller.
Battery charger reduces its output, if required, to avoid overload of supply when system consumption is high.
-Charges two separate batteries. For example the starter battery and the service battery of a boat or mobile home.
- Programmable charge current ratio (standard setting: equal current to both batteries).
-Charge voltage settings for three battery types (Gel, AGM and Flooded).
-Internal temperature sensor and optional remote temperature sensor.
- Protected against over current.
- Protected against short circuit.
- Protected against reverse polarity connection of the solar panels and/or battery.
BlueSolar MPPT 12/24-40
40A at 12V or 24V
- Maximum Power Point Tracking (MPPT) controller. Increases charge current by up to 30% compared to a PWM controller.
-Charge voltage settings for eight battery types, plus two equalize settings.
- Remote temperature sensor.
- Protected against over current.
- Protected against short circuit.
- Protected against reverse polarity connection of the solar panels and/or battery.
- With low voltage load disconnect output.
BlueSolar MPPT 12/24-40
Blue Solar Charge controllers
Victron Energy B.V. / De Paal 35
1351 JG Almere / The Netherlands
Phone: +31 (0)36 535 97 00
Fax: +31 (0)36 535 97 40
e-mail: [email protected]
www.victronenergy.com SAL064120020 - 00 - 1004

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project