Florida Pneumatic UT8006 Heavy Duty Ratchet Ratchet wrench User manual

PLEASE READ AND FOLLOW ALL WARNINGS

Read Operating Instructions

Always become familiar with all the instructions and warnings before operating any power tool.

Always Wear Approved

Eye Protection

Impact resistant eye protection should meet or exceed the standards as set forth in the United

States ANSI Z87.1, Occupational and Educational Eye and Face

Protection. Look for the marking

Z87.1 on your eye protection to insure that it is an approved style.

For further information, ANSI Z87.1,

Occupational and Educational Eye and Face Protection, is available from the American National

Standards Institute, Inc., 11 West

42nd Street, New York, NY 10036.

Hearing Protection is

Recommended

Hearing protection should be used when the noise level exposure equals or exceeds an 8 hour timeweighted average sound level of 85 dBA. Process noise, reflective surfaces, other tools being operated nearby, all add to the noise level present in your work area. If you are unable to determine your noise level exposure, we recommend the use of hearing protection.

Avoid Prolonged Exposure to

Vibration

Tools can vibrate during use.

Prolonged exposure to vibration or very repetitive hand and arm movements, can cause injury. Stop using any tool if discomfort, tingling feeling or pain occurs. You should consult your physician before resuming use of the tool.

90 PSIG Maximum

This tool is designed to operate at an air pressure of 90 pounds per square inch gauge pressure (90 PSIG) maximum, at the tool. Use of higher air pressure can, and may cause injury. Also, the use of higher air pressure places the internal components under loads and stresses they were not designed for, causing premature failure. The air supply should be clean and dry, preferably lubricated.

For best results, drain the moisture from your compressor daily.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks, cement and other masonry products

• Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles.

Florida Pneumatic Manufacturing Corporation

851 Jupiter Park Lane, Jupiter, Florida 33458

Toll Free 1-800-327-9403

UT8006

3/8” Heavy Duty Ratchet

Description

Florida Pneumatic ratchet wrench is designed for a wide variety of fastening applications. This unit features a lever type throttle for convenient operation, front exhaust directs air away from operator and a ball type socket retainer for quick and easy socket removal. 1 1 /

8

" ratchet head height for use in tight areas.

devices as furnished by the manufacturer. Where an air tool is modified or altered, the modifier shall provide the safeguards to enable it to be safely used in the operations intended and to comply with any applicable provisions as contained in ANSI B186.1.

Safety Instructions

The following instructions are furnished as general guidelines for use of your pneumatic tool. They cannot comprehensively cover all possible or conceivable uses of the subject tool. For additional information on the safe use of air tools, we advise you to obtain a copy of ANSI B186.1 Safety Code for

Portable Air Tools, available from the following source:

American National Standards

Institute, Inc.

11 West 42nd Street

New York, NY 10036.

The use of the word “shall” in the following instructions, indicates that adherence to the particular requirement is necessary to conform to ANSI

B186.1.

Tool Application and Usage

Portable tools shall be used only for the purposes intended in their design and within the capacity for which they were intended and rated. It shall be the tool owner’s and/or employer’s responsibility to instruct each operator in the safe use of the tool. Tools shall not be used without guards and safety

Tool Installation

Pressure regulators shall be used to limit air pressure to the rated pressure where the supply pressure exceeds the tool’s rated pressure. Air hoses and lines shall be relieved of compressed air before being disconnected or disjointed, unless there is automatic valve closing protection at the joint being separated. Synthetic lubricants which can cause deterioration of elastomer seals shall not be used in air systems of air tools.

Tool Maintenance

It shall be the tool owner’s and/or employer’s responsibility to assure that tools are maintained in a safe operating condition. Tool maintenance and repair shall be performed by authorized, trained, competent personnel. Tools shall be disconnected from their compressed air supply before repairs are attempted.

Repairs shall be consistent with the manufacturer’s recommended procedures. Tool, hoses and fittings shall be replaced if unsuitable for safe operation.

It shall be the tool owner’s and/or employer’s responsibility to keep required rating markings and warnings on the tool in legible condition.

Read these instructions carefully before attempting to install, operate or service this Florida Pneumatic product. Failure to comply with the instructions could result in personal injury and/or property damage!

Retain these instructions for future reference.

FPMC

UT8006

3/8” Heavy Duty Ratchet

Drive size..............................................................................................................................3/8"

Free speed ..................................................................................................................200 RPM

Max. Torque................................................................................................................60 ft/lbs.

Bolt Capacity........................................................................................................................1/2”

Weight.........................................................................................................................2-1/2 lbs.

Overall length...............................................................................................................10-1/2"

Recommended hose size..........................................................................................3/8" I.D.

Air inlet......................................................................................................................1/4" NPT

Maximum operating pressure...................................................................................90 PSI

Parts Breakdown for UT8006

USE ONLY POWER SOCKETS & ACCESSORIES

Sockets and accessories used shall be of the power socket type. Always check sockets, retainers and drives regularly for wear or damage and replace whenever necessary

UT8006

3/8” Heavy Duty Ratchet

Replacement Parts for UT8006

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

18

19

20

21

22

23

24

24-1

25

26

14

15

16

17

9

10

10-1

11

12

13

7

8

5

6

2

3

4

POS# PART NO.

1 9225-00201

9149-00301

9113-00303

9225-00401

9111-00405

9111-00802

9111-00706

9212-01402E

9113-00505

9540-00112-STC

9149-00304

9225-00501

9149-00105

9240-00204

9610-00103

9225-00103

9341-00103

9240-00203

9149-00101

9212-01304

9442-00202

9141-00202

9111-00406

9243-00302

9141-00602

9225-00602

9242-00302

9310-0020301

9149-00106

9111-00604

9211-01303

9444-00102

9112-01303

9411-0110301

9111-00407

9510-003041

9113-00314

9211-00302

9342-00101

9113-00306

9149-00202

9311-01004

9113-00602

DESCRIPTION

PLUG

O-RING

THROTTLE VALVE SPRING

VALVE

VALVE STEM

VALVE BUSHING

AIR INLET BUSHING

THROTTLE LEVER

SPRING PIN

HANDLE

EXHAUST DEFLECTOR SEAL

BEARING CAP

BALL BEARING

REAR END PLATE

ROTOR

ROTOR BLADE

CYLINDER

FRONT END PLATE

BALL BEARING

WASHER

INTERNAL GEAR

PLANET GEAR

GEAR PIVOT

GEAR PLATE

BUSHING

EXHAUST DEFLECTOR

CLAMP NUT

RATCHET HOUSING

NEEDLE BEARING

CRANK SHAFT

DRIVE BUSHING

RATCHET YOKE

WASHER

REVERSE BUTTON

PAWL PIVOT

RATCHET ANVIL

SPRING

SPRING CAP

RATCHET PAWL

FRICTION SPRING

STEEL BALL

THRUST WASHER

RETAINING RING

1

1

1

1

1

1

1

1

1

1

1

2

2

1

1

3

3

1

1

1

1

1

1

1

1

1

1

1

1

1

2

1

1

1

4

1

1

1

1

1

1

1

Q’TY

1

Limited Warranty

Florida Pneumatic warrants its tools to be free from defects in material and workmanship for two years from the date of purchase. This warranty does not apply to tools which have been abused, misused, modified or repaired by someone other than Florida Pneumatic or its authorized service centers. If a Florida Pneumatic proves defective in material of workmanship within one year after purchase, return it to any authorized service center or to Florida Pneumatic, freight prepaid. Please enclose your name, address and adequate proof of purchase date with a brief description of the defect. Florida Pneumatic will, at its option, repair or replace defective tools, free of charge. Repairs or replacements are warranted as described above for the remainder of the warranty period.

Florida Pneumatic's sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool. There are no other warranties expressed or implied and Florida

Pneumatic shall not be liable for incidental, consequential or special damages, or any other damages, costs or expense of repair or replacement as described above.