Sears | Kenmore 758.144118 | Owner`s Manual (General)

f
READ AND
SAVE THESE
iNSTRUCTiONS
SFAIRS
Modem No.
758.144118
QUIETCOMFORT
CONTEMPORARY
WHOLE HOUSE
HUMmDIFIER
FOR YOUR
12 Gallon Output
Digital
READ
ALL iNSTRUCTiONS
CAREFULLY
Sears, Roebuck
Part No. SP6561
with
Readout
® Operating _nstructions
o Parts List
and Co., Hoffman Estates,
IL 60179 U.S.A.
Printed in Canada
r
FULL ONE YEAR
WARRANTY
ON HUMIDIFmER
If within one (1} year from the date of purchase, this humidifier falls due to a defect in
material or workmanship, Sears will repair it, free of charge. If within two (2) years from
the date of purchase, the motor falls due to defect in material or workmanship, Sears
will repair it free of charge.
This warranty service is available by simply returning the humidifier to the nearest Sears
Store, and it will be repaired or replaced, at Sears option, free of charge.
This warranty applies onRy while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., D/Sf7 WA, Hoffman Estates, mL60179
GENERAL SAFETY INSTRUCTIONS
Safety
Signam Words
DANGER: means if the safety
not followed,
someone
will
injured or killed.
means if the safety
WARNING:
not followed,
someone
injured or killed.
information
is
be seriously
information
could
5.
Do net put
humidifier.
6.
Do not allow to be used as a toy. Close
attention
is necessary when used by or
near children.
7.
Never
is
be seriously
use your
is missing
8. To reduce
CAUTION:
means if the safety information
is
not followed,
someone
may be seriously
injured or killed.
foreign
objects
humidifier
inside
while
the
any par
or damaged
in any manner.
the risk of electrical hazard
damage
to humidifieg
do not tilt, jolt
tip humidifier
while unit is running.
or
or
1. To reduce the risk of fire or shock hazard, plug
humidifier directly into a 120V, A.C. electrical
outlet. Do not use extension cords.
9. To reduce the risk of damage to humidifier,
2.
10.To reduce
Keep the electric
unplug humidifier, when the base is empty
or when the humidifier is not in use.
cord out of traffic areas.
To reduce the risk of fire hazard, never put
the electric cord under rugs, near heat registers, radiators,
3. Always
stoves or heaters.
unplug
the
the risk of accidental
shock, do not touch
with wet hands.
11 .Note the warning
humidifier
electrical
the cord or controls
labe! shown
below.
before
moving it, before cleaning, or whenever
the humidifier
is not in service.
4.
Keep the humidifier
clean.
Table of Contents
Warranty Information ..................................
General Safety Instructions ........................
To Save A Service Call ...............................
Know Your Humidifier .................................
2
2
2
3
Humidifier Operation
.................................
Unpacking and Assembly ...........................
Location Instructions
.................................
4
4
5
Electrical
5
Hook-Up
......................................
To Save a Service
Check the following
not operating.
1. Is power
cord
2. Is there
ebctrical
if your
attached
power
Water Fill ..................................................
6-7
Operating Humidifier Controls ................... 7
Using Your Humidifier ...............................
11
Operating Tips for Best Performance ....... 11
Replacement
and Care of Filters ........ 12-18
Cleaning Your Humidifier .....................
Troubbshooting
..................................
Repair Parts .........................................
14-15
16-17
18-19
Carl
humidifier
is
3. Is aidlow control in operating
position?
4. Is humidity
control set high enough?
to outlet?
5. Is the cabinet
to outlet?
2
sitting
on a level surface?
Know Your Humidifier
Fan Assembmy
Bottme Handte
Speed Control
Base
Humidistat
(On power cord)
"_-- Filter:
42-14906
Replacement
Casters
--_
42_14411
Gallon Output/24 hrs
Capacity of Bottle
Capacity of Base
Sq, Ft, Coverage
Fan Speeds
Repiacement Filter
Power Light
Fill Light
Auto Humidistat
Auto Shut Off
Controls
Casters
CUL Listed
Volts
Hertz
Amps
Watts
12
1,9 Gallons
2,0 Gallons
2500
4
42-14906
Yes
Yes
Yes
Yes
Electronic(Push Button)
Yes (4)
Yes
120 A,C,
60
0,80
8O
* Based on an area with average insulation
and an 8 foot ceiling height,
No.
Humidifier
Operation
Your new Sears humidifier is designed to
satisfy home humidity requirements
through the principle of evaporation of
water in the air.
After water is added to the humidifier, the
filter begins to soak up the water and wilI
become saturated in approximately 30
minutes. Air drawn in through the openings in the lower housing passes through
the filter by means of a circulation fan.
As air passes through the filter, moisture is
absorbed into the air and then released in
the form of vapor. No water droplets will
enter the home. All evaporation into the air
takes place in the humidifier, which means
that the residue left by evaporating water
is not passed into the home, but remains
in the filter.
This natural process of evaporation helps
eliminate the chance of white dust in the
humidified output air.
CAUTION: Use onmy 42-14900 EPA
Registered Bacteriestat
avaimabme
from SEARS Retail store. Under no
circumstances
should you use water
treatment products designed for
Roto beretor Umtrasenic humidifiers.
Unpacking
Humidified air is
then reReased
through
the top
Dry'air
enters
through
the louvers
in the
housing
CAUTION: To reduce the risk of
injury, fire or damage to humidifier,
use onmy cmeaners specifically
recom_
mended for humidifiers.
Never use
flammabJe, combustibme or poisonous
materials to clean your humidifier. To
reduce the risk of scamds and damage to humidifier, never put hot water
in humidifier.
and Assemb/y
Your new Sears Kenmore humid[tier is
supplied with four swivel casters for ease
of maneuverability. Remove the casters
from the top of the packing material
inside the carton. The casters press into
the bottom of the base at the locations
shown. To make assembly easier remove
the water bottle, housing assembty and
filter and flip the base upside to install
See steps 2-4 of "Replacement and Care
of Filters" section on page 12 for procedure. Take care not to damage the floats
or base assembly if choosing this
method of assembly. Press casters into
location beside X.
Note: Casters should be
ally. Do not use any tools
Once installed return the
nal state and proceed to
Instructions.
installed manuto install them.
unit to its origi"Location
Location Instructions
Step 1
Place humidifier on a flat level surface in
an area of house where most humidity is
needed, or one which would likely result
in moist air being circulated throughout
the house such as near a cold air return.
Placing the unit Ievel is very important.
Special attention should be given to
unit's Ievel if the humidifier is Iocated on
carpeting. Moist air (humidity) produced
will disperse into the whole house, but
the area cIosest to the unit wiII have the
highest humidity. If the unit is positioned
close to a window, condensation may
form on the window pane. If this is not
appropriate the unit should be repositioned in another location.
NOTE: Due to release of cool, moist air
from humidifier, it is best to direct air
away from home thermostat and hot air
registers, it is best to position humidifier
next to an inside wail Not air registers
and cold air from outside walls can affect
the efficiencies of the controls. Unit
should not be placed where warm air
from a hot air register blows directly on
unit.
Electrical
-The humidifier should be positioned with
Stepback
2 (cord exit side) and left side, at
the
least 2 inches away from the wall. Air
needs to enter through all of the louvers
in the housing assembly in order for the
humidifier to operate at peak efficiency.
Note: Be sure humidistat located
approximately
4 inches outside humidF
tier body on power cord is free from
obstruction
and away from any hot air
register.
Hook-Up
Locate nearest ! 20V A.C. wall socket in
the location desired, preferably on inside
wall. With the humidifier in the desired
location, route the electrical cord safely
so no one will trip or upset the humidifier. Plug in the electrical cord.
To reduce the risk of electrical shock,
this humidifier has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet,
reverse plug. If it still does not fit, contact
a qualified electrician to install the proper
outlet. Do not change the plug in any
way.
1
Water Fill
WARNING: To reduce the risk of
shock, aBways unpBug humidifier
before cmeaning or servicing,
WARNING: To reduce the risk of fire
or shock hazard, do not pour or spill
water into controm or motor area,
If controms get wet, let them dry
compmeteBy and have unit checked by
authorized service personnel before
plugging in,
. Bottme
This humidifier is designed for use with
the water bottle located to the right of the
upper grill. The water bottle holds 1.9
gallons of water. The humidifier should be
positioned where it will be operating.
To filI the whole house humidifier, grasp
the bottle handle at the top of the bottle
and Iift it straight up and away from
humidifier base. Take care not to bump
or damage spring valve assembly on
bottom of bottle.
NOTE: If it is desired to use approved
bacteriostat, follow directions correctly.
The bottle of the whole house humidifier
will hold 1.9 gallons of water.
The water bottle is designed with an "EZ-FilI Side-Cap". Remove the "E-Z-Fill
Side-Cap" on the side of the water bottle
by twisting counterclockwise.
Place the opening of the water bottle
under a water faucet and fill. If desired,
add Sears liquid bactedostat (stock number 42-14900) to help control the build up
of bacteria and algae. Do not use solid
water treatments. Solid debris could
make the lower valve leak.
Install the "E-Z-FilI Side-Cap" by twisting
clockwise. Hand tighten only.
Check for possible meaks by perform_
ing the following:
1. Grasp bottle handle and hold the bottle upright over a sink.
2. Press up on valve plunger for about
one second to let out a little water.
3. Release the plunger.
Spring
Valve Assembly
4. Listen for air bubbles. Look for leaks
around the "E-Z-Fill Side-Cap" and
valve plunger.
The water bottle may be filled at anytime
as necessary during operation. To benefit
from Iess frequent filling let the humidifier
exhaust both the water from the bottle
and base before filling.
The unit is now ready for operation.
5. If you hear air bubbles or see leaks,
retighten the "E-Z-Fill Side-Cap" and
repeat steps 1-4.
Wipe off excess water from the bottle.
Position the water bottle back into the
humidifier base to the right of the grille.
The "E-Z-FilI Side-Cap" must be facing
outward. When positioned properly, the
plunger will open and water will flow into
the base. The base will hold the entire
contents of the water bottle. Allow up to
one minute for the water to flow into the
base. Once the bottle is empty, remove it
and refill it as mentioned earlier. Return it
to the right side of the grille. The humidifier is now filled to capacity.
Operating
Humidifier
Controls
The operating controls of your Kenmore
Quiet Comfort whole house humidifier
are !ocated towards the front of the
humidifier.
play indicates that the room humidity is
less than 25 %.
Digital
Display
Familiarize yourself with the controls.
Refer to the diagram of the control
area for the correct nomenclature used in
this manual.
To Operate
the Controls
Power Button / Light
When the unit is plugged in and the
power button is pressed once the red
power light wilI come on. The power light
will stay on until the power button is
pressed again turning the unit off or until
the unit is unplugged.
Digital Display
The digital display wilI also show readouts when the unit is turned on. Initially
there is a slight delay while the electronics calibrate. Two bars (- -) flash during
this time. Once calibration is complete a
ROOM humidity reading between 25% 95% will be displayed. A flashing 25 dis-
Refill
Light
On
Light
Note: The default settings at initia! startup are WHISPER fan speed and 65%
SET humidity. After desired settings are
selected by the user, they remain as
defaults as Iong as the unit remains
plugged in and there is no power interruption. If the unit is unplugged the
originam default settings are employed.
IMPORTANT: Water damage may
resuBt if condensation
starts to form
on windows or walls, Humidity SET
point shoumd be lowered until
condensation
no monger forms,
Operating
Humidifier
Controls
(cent'd)
Speed Button
This humidifier is equipped with a 4speed fan control Each push of the
speed button advances the mode
through the settings of HIGH, MEDIUM,
LOW and WHISPER. The selected setting is displayed on the digital readout.
The higher the setting, the faster water is
evaporated and released into the air.
WHISPER is the quietest setting and is
provided for conditions that do not
require a rapid evaporation rate.
Humidity Control
The +/- buttons allows you to adjust the
humidity to suit your needs. This
humidifier wiII automatically cycle on and
off as required to maintain the selected
setting. The readout displays both actual
(ROOM) and desired (SET) humidity percentage (%) settings. The ROOM reading
is the larger display of the two. The
ROOM readout is dispiayed in 1% increments and has a range of 25% to 95%.
If the room humidity level is equal to or
less than 25% the display will show a
flashing 25.
The SET readout has a range of 30% to
65% and is adjusted in increments of
5%. Each press of the
(+} button increases the setting by 5%
and conversely each press of the ( - )
button decreases the setting by 5%. A
SET point of 65% operates the humidifier
continuously regardless of the ROOM
reading.
The humidistat that senses the readings
is located on the power cord. Insure that
it is free from obstruction.
Constant
On Setting
Operating
Humidifier
Controls
(cont'd)
Refill Light
The humidifier base and bottle hold approximately 2 gallons of water each. The bottle
empties into the base during operation.
When the base empties the red RENLL
light will illuminate informing additional water
is required. Also at this time the unit will
automatically
switch into "DRY OUT
MODE" and continue to run on WHISPER
speed until the filter is dry. The message
"DRY OUT MODE" will appear on the digi-
Refill Light
tal display and the fan speed will switch to
WHISPER speed. Note: The digital display
will still show the speed the humidifier was
operating in before the REFILL light turned
on even though the fan is operating at
WHISPER speed. During this time the room
humidity level will continue to be monitored
and the humidifier will cycle the fan on and
off as required. If DRY OUT MODE is not
desired, refill the humidifier with water.
Note: Once the dr,/out cycle is complete
the fan will shut off and the RENLL light will
stay illuminated. The humidifier will automatically start again when it is refilled.
Bottle Empty _ndicator
This humidifier employs a "double fill" bottle
system. If the base is empty the contents of
the bottle will completely
empty into it. The
bottle can be refilled and returned to the
unit. The humidifier
viding its maximum
is now capable of prorun time between fills.
Once the bottle empties a flashing "BOTTLE EMPTY" message will appear on the
display panel. The unit will continue to run
as programmed
but the option of refilling
the bottle is presented. Once filled the flashing message will turn off.
Bottme Empty
Humidifier
Chock
Operations
Fimter _ndicator
The ability of any humidifier
to efficiently sup-
ply humidity output relies heavily on the condition of the filter. As the filter loads with
trapped
impurities
found in water it gradually
loses its wicking capability. When this happens moisture output is reduced and the
humidifier has to work longer to satisfy the
selected setting. When such a condition
Check
FHter
occurs, a flashing "CHECK FILTER" message
will be displayed, disconnect the power and
check the condition of the filter.
if a buildup of deposits and severe discoloration is evident replace the filter to restore
maximum
efficiency.
Humidistat
The humidistat located on the power
cord senses the percentage of humidity
in the air. It causes the humidifier to cycle
on and off to maintain the selected
humidity SET point. The fan will turn on if
the "ROOM" reading fails 3% below the
SET point and will continue to run the
humidifier until a reading of 1% above
the SET point is achieved. At this point
the fan wilI stop. The fan will remain off
until the ROOM reading fails 3% below
the SET point again.
Note: Be
mately 4
on power
and away
sure humidistat
located appro×iinches outside humidifier
body
cord is free from obstruction
from any hot air register.
Dry
Dry Out Mode
When both the water bottle and the base
are empty the red REFILL light wilI illuminate and the humidifier wilI automatically
switch into DRY OUT MODE. The message DRY OUT MODE will appear on the
digital display and the fan speed wilI
automatically switch to WHISPER speed.
Note: The digital display will show the
speed the humidifier was operating in
before the REFILL light turned on even
though the fan is operating on WHISPER
speed. During this time the humidifier will
continue to cycle the fan on and off as
required until the filter is completely dry
thus producing nomoisture output. Once
dE/, the fan will shut off leaving you with
a dry humidifier that is less prone to
Out
Mode
Note: Fan automatically
switches to
""WHISPER'" speed during ""DRY OUT MODE"
DispBay win still show programmed
speed.
i.e: NIGH
mold and miIdew growth. The red
REFILL Iight wiII be illuminated and the
humidifier is ready for cleaning or refilling
as desired.
10
Using Your Humidifier
1. Place the humidifier where you intend
to run it and be sure it is plugged in
and fulI of water.
your desired humidity. It may take severa!
fillings to bring the ROOM humidity level
up to the SET point. A faster fan speed
wilI accomplish this quicker. Once established adiust the fan speed to suit your
needs.
2. Press the POWER button once to turn
the humidifier on. The red power light
wilI illuminate.
IMPORTANT: Water damage may
resuBt if condensation
starts to form
on windows or wails. Humidity SET
point shouBd be mowered untim
condensation
no monger forms.
The fan wilI immediately operate on
WHISPER speed and the SET humidity
percentage will read 65 on the digital display.
NOTE: Humidifier fan should operate at
initial start up. If it does not, refer to the
"Trouble Shooting" section on page 16 of
this manual
5 If the humidifier stops running and the
red REFILL light is not illuminated, the
humidity level is at the normal requirements for that SET point. The table
below shows recommended indoor
humidity levels as it relates to outdoor
temperatures.
3. Wait a few seconds while the humidifier takes a ROOM humidity reading.
During this time two bars (- -) will flash
on the display.
Recommended
4. Once a ROOM reading has registered
proceed to adjust the desired humidity
percentage by pressing the + or button. It will change the desired SET
humidity level in increments of 5%.
When Outdoor
Temperature
If the room reading is a flashing 25, the
humidity level is low. A SET point of 30%
- 40% is recommended but there may be
conditions that require a different setting.
Depending on your particular environment it could take 24 hours and in some
cases longer for the humidifier to reach
Operating
is:
Indoor
Remative
Humidity
-10OF
20%
0OF
25%
10OF
30%
20°F & above
is:
35%
Tips for Best Performance
1. Position the humidifier next to an
inside wall at least 2 inches from the
wall and away from any heat registers.
4. Regular cleaning as instructed in
"Cleaning Your Humidifier" section of
this manual is recommended.
5. Replace the evaporative wicking filter
at least once per humidification season or more depending on water conditions in your area.
6. Ensure humidistat located on power
cord is free from any obstruction and
is away from heating vents or other
sources of heat.
2. Do not restrict airflow from entering or
exiting the humidifier.
3. Use 42-14900 EPA approved bactedostat (available at your local Sears
store) to retard bacteria growth that
may cause odors and may be harmful
to your health.
11
Replacement
and Care of Filters
WARNING: To reduce the risk of
shock or injury from mov{ng parts,
atways unp{ug humidifier before
removing or replacing any parts.
CAUTION: To hemp retard bacteria
growth and keep maximum efficiem
cy, the filter should be repmaced at
least once per season, or more often
under hard water conditions.
Use
Sears recommended
repmacement
filter.
To replace the filter in your Kenmore
Quiet Comfort Whole House humidifier,
follow the instructions below.
Unplug humidifier.
Before removing the filters, we recommend moving the humidifier to an
area where floor coverings are not
susceptible to water damage. (i.e.
kitchen or bath areas.)
Grasp
Housing
Assembly
SecureRy
..... ,_
and Lift OFF
Remove the water bottle and set
aside. Be sure not to bump or damage
the lower spring valve.
3. Grasp the housing assembly and Iift
straight up and away from the base
and set aside. The filter is now accessible.
Filter
4. Take note of the filter position.
Remove the filter and dispose of
properly. You may want to clean
the base at this time. See the
"Cleaning Your Humidifier" section
of this manual.
_.J-
Base
12
Replacement
and Care of Filters
5. InstalI a new filter (42-14906) into the
base. CoiI the filter and position it
between the uprights in the bottom of
the base. The start and finish of the
coiI should be captured at the center
of the base (see diagram) and the filter
should be resting on the floor of
the base.
Base
(continued)__
Uprights
se
6. Return the housing assembly to the
top of the base. Return the water bottle to the right of the housing assembly
and reposition the humidifier to its
operating position.
7. The humidifier is now ready to be filled
for operation.
\
\.
/_
Align housing
assemMy
bottom with
top of base
and reposition
seeureUy,
Return bottle
to right side of
humidifier.
13
Cleaning
Your Humidifier
WARNING: To reduce the risk of
injury, fire or damage to humidifier,
use only cleaners specifically
rec=
ommended for humidifiers.
Never
use flammable, combustible
or poisonous materials to clean your
humidifier. To reduce the risk of
scalds and damage to humidifier,
never put hot water in humidifier.
Step 2
To Remove
Parts
1. Remove the water bottle and set
aside. Be sure not to bump or damage the lower spring valve.
Grasp the housing assembly and Iift
straight up and away from the base
and set aside. The filter is now
accessible.
CAUTION: Locamwater purity varies
from area to area and under certain
conditions water impurities and airborne bacteria may promote the
growth of microorganisms
in the
reservoir of the humidifier.
3= Take note of the filter position.
Remove the filter and set aside or
dispose of properly.
NOTE: There may be a little water still in
the base. Carefully dump the water out
or remove with a sponge.
To retard bacteria growth that may
cause odors and be harmful to your
heamth, use onmySears replacement
fimters. We amsorecommend
using
ERA approved bacteriostat,
42=14900
and humidifier cleaner 42=14713,
availabme at your Iocat Sears store.
Step 1
To make cleaning easier, the humidifier
base should be empty and completely
dried out. To accomplish this, use the following method:
a. Allow the humidifier to run until the
red REFILL light illuminates and the
automatic shutoff has stopped the
humidifier fan.
b. Unplug humidifier.
WARNING: if humidifier is not un=
plugged, fan coutd start after housing
is removed.
14
Note:
Remove
water
before
excess
cleaning
Cleaning
of Humidifier
(continued)
Step 3
End
of Season
Maintenance
1. Follow "Bi-Weekly Maintenance"
instructions at end of humidification
season.
Removing
Scale
1. Fill the humidifier base with one 8 oz.
cup of undiluted white vinegar. Let
solution stay 20 minutes,
2. Clean all interior surfaces with a soft
brush. Dampen a soft cloth with undiluted white vinegar and wipe out the
base to remove scale,
2. Remove filter and dispose of properly.
3. Let humidifier dry completely before
storing, Do not store with water inside
base or bottle,
4. Store in cool, dry location.
5. Install a new filter in clean humidifier
before next season begins.
Note: "Bi-Weekly Maintenance" is
also recommended if you do not plan
to run the humidifier for one week or
more.
3. Rinse thoroughly with clean warm
water to remove scale and cleaning
solution.
Disinfecting
Base
1. Pour 1 gallon of water and 1 teaspoon
chlorine bleach into the base. Let
solution stay for 20 minutes, carefully
swishing every few minutes. Wet all
surfaces normally exposed to wateE
2. Empty base after 20 minutes. Rinse
with water until bleach smell is gone.
Allow unit to db/out completely.
NOTE: The water bottle should be
cleaned in the same manner as the base.
Rinse thoroughly with clean water after
all steps are complete.
Position start and
finish of coiled fluter
er of base.
Step 4
Replacing
Parts
1. InstalI a new filter (42-14906) or the
filter previously set aside if it is in
good condition into the base, Coil the
filter and position it between the
uprights in the bottom of the base,
The start and finish of the coil should
be captured in the centre of the base
(see diagram) and the filter should be
resting on the floor of the base.
and
reposition
secureUy,
2. Return the housing assembly to the
top of the base, Return the water bottle to the right of the housing assembly and reposition the humidifier to its
operating position,
3. The humidifier is now ready to be
filled for operation.
top
15
of base
Troubleshooting
Trouble
Probable
Cause
Remedy
Red power light and digital
display not illuminated.
" No Powera
,, Power button has not been
depressed,
,, Check 120 volt power sourcea
,, Press power button once to
turn on.
Fan not operating (Red power
light and digital display is
illuminated),
,, ROOM humidity level is 1%
or more above SET humidity
level.
,, Raise SET humidity level if
desired.
Fan running continuously.
,, SET humidity level is 65%.
,, A SET humidity percentage
of 65% operates fan
continuously. Adjust SET
level between 30% - 60%.
o Continue to run until desired
e ROOM humidity level is 3%
or more below SET humidity
level.
humidity level is achieved.
This may take up to 48 hours
initially.
o This unit is designed to satisfy an area up to 2,500 sq. ft.
e Humidifier under size for
requirements.
Poor evaporation
of water,
e CHECK FILTER message
flashing,
o Change to a fresh new
filter.
Bottle empties completely,
e This is normal for initial filling,
o Refill bottle for maximum run
time.
Bottle continues to empty
after initial filling,
e Air is entering water bottle,
o Ensure fill cap is tightened
securely.
,, Ensure gasket on fill cap is
in place.
o Check for leak in water bottle.
Bottle not emptying.
,, Spring Valve Assembly
damaged or missing post
in bottom of base.
,, Check orientation
of bottle.
Reposition so that spring
valve on bottom of bottle is
depressed by post in bottom
of base.
e The base will hold the con-
e Base full of water.
tents of water bottle (2.0 gallons). Continue to run
humidifier to deplete water
from base.
CAUTION: Use only 42-14900
Retail store,
EPA Registered
Use of other water treatment
products
Bacteriostat
may damage
the filter component.
Under no circumstances
should you use water treatment
Roto beretor Ultrasonic humidifiers,
16
availabme from Sears
products
designed
for
Troubleshooting
Trouble
Probable
Cause
Remedy
Display blinks or fan moves
slightly when humidifier is
plugged in.
" Normal
,, No action required.
'CHECK FILTER" message
does not appear even when fib
ter is dirty or humidifier performance is clearly reduced.
,, Humidistat on power cord is
being heated,
,, Move power cord away from
any source of heat or
obstruction.
Fan operating slower than
speed registered on digital display.
e Humidifier
MODE".
e Humidifier automatically
switches fan speed to 'WIllSPER" when 'DRY OUT
MODE" message is displayed.
Humidifier not shutting off during "DRY OUT MODE".
,, Filter not dry.
in 'DRY OUT
,, During "DRY OUT MODE" the
humidifier will continue to run
on 'WHISPER" speed as
required for up to 2 hours or
until the filter is completely
dry.
CAUTION: Use only 42-14900
Retail store,
EPA Registered
Use of other water treatment
products
Bacteriostat
may damage
the filter component,
Under no circumstances
should you use water treatment
Roto beretor Ultrasonic humidifiers,
17
availabme from Sears
products
designed
for
Repair Parts
Parts List for Sears Humidifier
Model No. 758.144118
_13
13
18
For repair-in your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
®
(1-800-469-4663)
day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Your Home
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655
(U.S.A.)
Para pedir servicio
de reparaci6n
a domicilio,
1-800-361-6665
Au Canada
y para ordenar piezas:
1-888-SU-HOGARSM
(Canada)
pour service en francais:
1.800.LE.FOYERMO
(1-800-533-6937)
(1-888-784-6427)
"
www.sears, ca
TM
S_4
Trademark
/
Trademark
/
Service Mark of Sears, Roebuck
and Co
TM
SM
'_ Marea Registrada
/
Marca de Fabdea /
Marca de Servicio de Sears, Roebuck
and
Mc Marque de commerce
/ MD Marque deposee
de Sears, Roebuck
and Co
® Registered
Part No, SP6561
Form. No. SP6561
Co
© Sears,
Roebuck
and Co
Printed JnCanada 10/04
Download PDF