Clarke | CCS185B | Specifications | Clarke CCS185B Specifications

CCS185B Circular Saw.fm Page 1 Wednesday, June 19, 2013 11:39 AM
185MM CIRCULAR SAW
MODEL NO: CCS185B
PART NO: 6462310
OPERATION & MAINTENANCE
INSTRUCTIONS
LS0613
CCS185B Circular Saw.fm Page 2 Wednesday, June 19, 2013 11:39 AM
INTRODUCTION
Thank you for purchasing this CLARKE 185mm Circular Saw.
Read this manual fully before you use this product and follow the instructions
carefully. In doing so you will ensure the safety of yourself and that of others
around you, and you can look forward to your purchase giving you long and
satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
SPECIFICATIONS
Model Number
CCS185B
Rated Voltage
230V~50Hz
Power Input
1200 W
No Load Speed
4800 RPM
Maximum Depth of Cut
65 mm @ 90o - 44 mm @ 45o
Blade Dimensions
185 mm Ø x 16 mm Bore
Sound Pressure Level LpA
90.8 dB(A)
Sound Power Level LWA
101.8 dB(A)
Uncertainty Factor (K)
3 dB(A)
Weight
3.95 kg
Vibration (main handle)
2.281 m/s2 Uncertainty Factor 1.5
Dimensions (L x W x H)
292 mm x 235 x 239 mm
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 3 Wednesday, June 19, 2013 11:39 AM
POWER TOOL SAFETY WARNINGS
WORK AREA
1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
3. Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use adaptor plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce the risk of electric shock.
2. Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
3. Do not abuse the cable. Never use it for carrying, pulling or unplugging the power
tool. Keep the cable away from heat, oil, sharp edges or moving parts. Damaged or
entangled cables increase the risk of electric shock.
4. When operating a power tool outdoors, use an extension cable suitable for outdoor
use. Use of a cable suitable for outdoor use reduces the risk of electric shock
5. If operating the power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in personal injury.
2. Use safety equipment. Always wear eye protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
3. Avoid accidental starting. Make sure that the switch is in the off position before
plugging in. Carrying power tools with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
4. Remove any wrench before turning the power tool on. A wrench left attached to a
rotating part may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 4 Wednesday, June 19, 2013 11:39 AM
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the correct accessories for your application. The
correct power tool will do the job better and safer at the rate which it was designed
for.
2. Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source before changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
4. Store idle tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate it. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many accidents are caused
by poorly maintained power tools.
6. Use the power tool and accessories in accordance with these instructions and in the
manner intended, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from intended could result
in a hazardous situation.
7. The performance of this tool may vary, depending upon variations in line voltage.
Extension cable usage may also affect performance.
SERVICE
1. Have your power tool serviced by qualified service personnel using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR ALL SAWS
a. Keep hands away from cutting area and the blade. Keep your second hand on
the auxiliary handle, or motor housing. If both hands are holding the saw, they
cannot be cut by the blade.
b. Do not reach underneath the workpiece. The guard cannot protect you from the
blade below the workpiece.
c. Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth
of the blade teeth should be visible below the workpiece.
d. Never hold the piece being cut in your hands or across your leg. Secure the
workpiece to a stable platform. It is important to support the work properly to
minimise body exposure, blade binding, or loss of control.
e. Hold the power tool by handles when performing an operation.
f.
Always use blades with the correct size and shape of arbor holes. Blades that do
not match the mounting hardware of the saw will run eccentrically, causing loss
of control.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 5 Wednesday, June 19, 2013 11:39 AM
g. Never use damaged or incorrect blade washers or bolt. The blade washers and
bolt were specially designed for your saw, for optimum performance and safety
of operation.
PREVENTION OF KICKBACK
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing
an uncontrolled saw to lift up and out of the workpiece toward the operator.
When the blade is pinched or bound tightly by the kerf closing down, the blade stalls
and the motor reaction drives the unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the
blade can dig into the top surface of the wood causing the blade to climb out of the
kerf and jump back toward the operator. Kickback is the result of saw misuse and/or
incorrect operating procedures or conditions and can be avoided by taking proper
precautions as given below.
a. Maintain a firm grip with both hands on the saw and position your arms to resist
kickback forces. Position your body to either side of the blade, but not in line with
the blade.
b. When the blade is binding, or when interrupting a cut for any reason, release the
trigger and hold the saw motionless in the material until the blade comes to a
complete stop. Never attempt to remove the saw from the work or pull the saw
backward while the blade is in motion or kickback may occur. Investigate and
take corrective actions to eliminate the cause of blade binding.
c. When restarting a saw in the workpiece, centre the saw blade in the kerf and
check that saw teeth are not engaged with the material. If the blade is binding,
it may walk up or kickback from the workpiece as the saw is restarted.
d. Support large panels to minimise the risk of blade pinching and kickback. Large
panels tend to sag under their own weight. Supports must be placed under the
panel on both sides, near the line of cut and near the edge of the panel.
e. Blade depth and bevel adjusting locking screws must be tight and secure before
making a cut. If blade adjustment shifts while cutting, it may cause binding and
kickback.
f.
Use extra caution when making a “plunge cut” into existing walls or other blind
areas. The protruding blade may cut objects that can cause kickback.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 6 Wednesday, June 19, 2013 11:39 AM
CIRCULAR SAW BLADE SAFETY WARNINGS
a. The maximum speed marked on the tool shall not exceed the maximum speed
marked on the blade.
b. Cracked circular saw blades shall be scrapped (repairing is not permitted).
Composite (tipped) circular saw blades, where the tip dimension is reduced to
less than 1 mm, shall be taken out of service.
c. Fastening screws and nuts shall be tightened using the tools supplied.
d. Clamping surfaces shall be cleaned to remove dirt, grease, oil and water.
e. Do not use loose rings or bushes to “make up” bore sizes on circular saw blades.
EXPLANATION OF SYMBOLS & PICTOGRAMS
Read Instruction Manual Before Use
Wear Eye Protection
Wear Gloves
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 7 Wednesday, June 19, 2013 11:39 AM
ELECTRICAL CONNECTIONS
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
Before switching the product on, make sure that the voltage of your electricity supply is
the same as that indicated on the rating plate. This product is designed to operate on
230VAC 50Hz. Connecting it to any other power source may cause damage.
This product may be fitted with a non-rewireable plug. If it is necessary to change the
fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or
damaged, the plug must not be used until a suitable replacement is obtained.
If the plug has to be changed because it is not suitable for your socket, or due to
damage, it should be cut off and a replacement fitted, following the wiring instructions
shown below. The old plug must be disposed of safely, as insertion into a mains socket
could cause an electrical hazard.
WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL
BROWN = LIVE
If the colours of the wires in the power cable of this product do not correspond with the
markings on the terminals of your plug, proceed as follows.
• The wire which is coloured Blue must be connected to the terminal which is
marked N or coloured Black.
• The wire which is coloured Brown must be connected to the terminal which is
marked L or coloured Red.
Plug must be BS1363/A approved.
Always fit a 13 Amp fuse.
Live
Neutral
(Brown)
(Blue)
Make sure that the outer sheath of the cable is firmly held by the clamp
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD)
This symbol indicates that this is a Class II product, and does not require
an earth connection.
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 8 Wednesday, June 19, 2013 11:39 AM
PART IDENTIFICATION.
1
Blade Lock
10
Mains Lead
2
Auxiliary Handle
11
Parallel Guide Locking Screw
3
Safety Lock Button
12
Bevel Adjustment Knob
4
On/Off Trigger
13
Mark For Bevel Cut
5
Handle
14
Mark For Straight Cut
6
Depth Adjustment Lever
15
Lower Guard Retracting Lever
7
Lower Guard
16
Hexagon Key
8
Blade Clamping Screw
17
Parallel Guide
9
Dust Extraction Outlet
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 9 Wednesday, June 19, 2013 11:39 AM
CARTON CONTENTS
The following items should be supplied in the carton. If any parts are missing or
damaged, please contact the Clarke dealer where you purchased the tool.
• 1 x 1200 Watt Circular Saw.
• 1 x 185 mm Ø x 16 mm Bore x 24 Tooth TCT blade.(assembled on tool).
• 1 x Parallel Fence.
• 1 x 6 mm Hexagon Key.
ADJUSTMENTS
DEPTH OF CUT ADJUSTMENT
1. Loosen the depth adjustment
lever.
2. Adjust the base plate until the
required depth of blade is
protruding through the base
plate.
3. Tighten the depth adjustment
lever.
NOTE: For optimum results, a full
tooth should just be visible
below the workpiece.
BEVEL ADJUSTMENT
1. Loosen the bevel locking knob.
2. Adjust the base plate to the
required angle (max 45o)
• Use the bevel scale as a guide
only, for accurate angles use a
protractor.
3. Tighten the bevel adjustment
knob to lock the base at the
required angle.
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 10 Wednesday, June 19, 2013 11:39 AM
MOUNTING AND USING THE PARALLEL GUIDE
MOUNTING
1. Slide the parallel guide into the
base plate as shown.
2. Secure in place using the parallel
guide locking screw.
ADJUSTING
1. Loosen the Parallel Guide Locking
Screw.
2. Adjust the Parallel Guide to the
required length.
• There is a scale on the parallel guide that can be used to give an
approximate guide. Always double check using an accurate ruler.
3. Tighten the Parallel Guide Locking Screw to secure the parallel guide in
position.
DUST EXTRACTION
The circular saw can be connected
to a dust extraction system, using a
suitable hose adaptor (not supplied).
• The internal diameter of the
dust extraction outlet is 30 mm.
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 11 Wednesday, June 19, 2013 11:39 AM
OPERATION & USE
CORRECT HAND POSITION
For your own safety, always hold the
circular saw as shown in this picture,
with one hand on the main handle
and the other on the auxiliary handle.
SWITCHING ON/OFF
The on/off trigger is fitted with a safety button which prevents the circular saw
from being started accidentally. To start the saw:
1. Press and hold the safety button.
2. Squeeze the on/off trigger at the
same time.
3. Release the on/off trigger to stop
the saw.
• The blade will continue to
rotate for several seconds after
the trigger has been released.
GUIDING THE CIRCULAR SAW
To achieve optimal results:
• Clamp the workpiece upside
down to minimise breakout.
• Follow the line drawn on the
workpiece using the 90o mark.
• If cutting a bevel angle of 45o,
follow the line drawn on the
workpiece using the 45o mark.
11
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 12 Wednesday, June 19, 2013 11:39 AM
MAINTENANCE
WARNING: DISCONNECT THE CIRCULAR SAW FROM THE MAINS SUPPLY
BEFORE FITTING REPLACEMENT BLADES, CLEANING OR ADJUSTMENT.
Keep the machine clean by wiping off dust with a clean cloth.
BLADE REPLACEMENT
1. Press and hold the blade lock and
remove the blade clamping
screw using the hexagon key
supplied by turning it anticlockwise.
• The blade will rotate until the
blade lock is fully engaged.
2. Retract the lower blade guard
using the retracting lever and
replace the blade.
• Make sure you pay attention to
the blade direction marking on
the blade.
• Spare blades are available
from your local Clarke dealer.
3. Replace the blade clamping
screw by hand until it is holding
the blade in position.
4. Press and hold the blade lock and turn the blade by hand until the blade
lock is fully engaged.
5. Tighten the blade clamping screw using the hexagon key supplied.
12
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 13 Wednesday, June 19, 2013 11:39 AM
PARTS DIAGRAM
13
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 14 Wednesday, June 19, 2013 11:39 AM
PARTS LIST
1
Screw
HTCCS185B01
37 Stator
2
Washer
HTCCS185B02
38 Square Connect Piece
HTCCS185B38
3
Outer Flange
HTCCS185B03
39 Bearing
HTCCS185B39
4
Saw Blade
HTCCS185B04
40 Bearing Sleeve
HTCCS185B40
5
Clamping Flange
HTCCS185B05
41 Housing
HTCCS185B41
6
Screw
HTCCS185B06
42 Label
HTCCS185B42
7
Flange For Lower Guard
HTCCS185B07
43 Carbon Brush Cover
HTCCS185B43
8
Lower Guard
HTCCS185B08
44 Carbon Brush
HTCCS185B44
9
Screw
HTCCS185B09
45 Carbon Brush Holder
HTCCS185B45
10 Lower Guard Retracting
Lever
HTCCS185B10
46 Rear Cover
HTCCS185B46
47 Screw
HTCCS185B47
11 Reset Spring
HTCCS185B11
48 Screw
HTCCS185B48
12 Output Shaft
HTCCS185B12
49 Left Handle Moulding
HTCCS185B49
13 Semi-circular Key
HTCCS185B13
50 Capacitor
HTCCS185B50
14 Bearing
HTCCS185B14
51 Switch
HTCCS185B51
15 Front Cover
HTCCS185B15
16 Positioning Steel Bush
HTCCS185B16
17 Drive Gear
HTCCS185B17
18 Shaft Circlip
HTCCS185B18
19 Oil Bearing
HTCCS185B19
20 Square Neck Bolt
HTCCS185B20
21 Nameplate
HTCCS185B21
22 Screw
HTCCS185B22
23 Positioning Circlip
HTCCS185B23
24 Washer
HTCCS185B24
25 Pin Screw
HTCCS185B25
26 Blade Cover
HTCCS185B26
27 Nut
HTCCS185B27
28 Self-locking Spring
HTCCS185B28
29 Bearing
HTCCS185B29
30 Blade Lock
HTCCS185B30
31 Blade-locking Button
HTCCS185B31
32 Screw
HTCCS185B32
33 Windshield
HTCCS185B33
34 Armature
HTCCS185B34
35 Wind Loop
HTCCS185B35
36 Screw
HTCCS185B36
HTCCS185B37
52 Right Handle Moulding
HTCCS185B52
53 Cable Clamp
HTCCS185B53
54 Cable Protector
HTCCS185B54
55 Cable
HTCCS185B55
56 Rivet
HTCCS185B56
57 Locking Knob
HTCCS185B57
58 Flat Washer
HTCCS185B58
59 Bevel Control Lever
HTCCS185B59
60 Nut
HTCCS185B60
61 Screw
HTCCS185B61
62 Locking Spring
HTCCS185B62
63 Parallel Guide Locking Nuts HTCCS185B63
64 Square Neck Bolt
HTCCS185B64
65 Sole Plate
HTCCS185B65
66 Depth Adjustment Lever
HTCCS185B66
67 Depth Adjusting Lock Rod
HTCCS185B67
68 Depth Adjusting Frame
HTCCS185B68
69 Hex Wrench
HTCCS185B69
70 Parallel Guide
HTCCS185B70
14
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 15 Wednesday, June 19, 2013 11:39 AM
DECLARATION OF CONFORMITY
15
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
CCS185B Circular Saw.fm Page 16 Wednesday, June 19, 2013 11:39 AM
Download PDF