- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Rievtech
- EXM -12DC-DA-R
- User's manual
- 380 Pages
RIEVTECH EXM -12DC-DA-R x-Messenger User’s Manual
Below you will find brief information for x-Messenger EXM EXM-12DC-DA-R. This is a compact and expandable telemetry module that combines a GSM/GPRS modem, PLC controller, data logger, Ethernet module, and multiple communication capabilities. You can use it for control and monitoring applications, such as building and parking lot lighting, managing automatic lighting, access control, watering systems, pump control, ventilation systems, and home automation.
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
U p d a t e d : F e b r u a r y 22 , 2 0 10 x
-Messenger
User’s Manual
Applied to EXM series CPU& Extensions.
Rievtech Electronic Co., Ltd
Version:V 1.4
Contents
Introduction
Getting started
Applications
x-Messenger functions
Installation and wiring
Configuring &software
Technical data
2
Introduction
Congratulations with your x-Messenger SMS/GSM/GPRS Micro-PLC provided by Rievtech
Electronic Co., Ltd.
The x-Messenger is a compact and expandable telemetry module combining industrial grade GSM/GPRS modem, PLC controller, data logger, Ethernet module, and multiple communication capability (1RS232&1RS485 ,MODUS ASCII/RTU/TCP, Mater/Slave).
Each module incorporates not only a real-time clock and calendar, but also provides support for SMS, Call-In,Email, Ring and optional expansion digital /analog -I/O modules and to enhance control and monitoring applications. Data adjustments can easily be performed via the keypad, the LCD display, or through the easy-to-use eSmsConfig.exe.
DIN-rail and panel-mounted options are both available, offering full flexibility to the various installation needs of your application.
The x-Messenger is available in 120V/240V AC or 12V and 24V DC versions, making it the ideal solution for relay replacement, or simple control applications with SMS control or alarming such as building and parking lot lighting, managing automatic lighting, access control, watering systems, pump control, ventilation systems, home automation and a wide field of other applications demanding low cost to be a primary design issue.
We strongly recommended taking the time to read this manual, before putting the x-Messenger to work. Installation, programming and use of the unit are detailed in this manual. The feature-rich x-Messenger provides an for off-line operation mode, allowing full configuration and testing prior to in-field service commissioning. In reviewing this manual you will discover many additional advantageous product properties, which will greatly simplify and optimize the use of your x-Messenger.
Valid range of this manual
3
The manual applies to devices of EXM series modules. For more information about expansion module or accessories, please refer to the correlative model instruction files.
Safety Guideline
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol; notices referring to property damage only have no safety alert symbol. The notices shown below are graded according to the degree of danger.
Caution
Indicates that death or severe personal injury may result if proper precautions are not taken
Caution
With a safety alert symbol indicates that minor personal injury can result if proper precautions are not taken.
Caution
Without a safety alert symbol indicates that property damage can result if proper precautions are not taken.
Attention
Indicate that an unintended result or situation can occur if the corresponding notice is not taken into account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.
4
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation.
Commissioning and operation of a device/system may only be performed by qualified personnel.
Within the context of the safety notices in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety practices and standards. Please read the complete operating instructions before installation and commissioning.
GSM network failure or power interruptions cannot guarantee a secure monitoring. The use of a prepaid SIM card is possible. It is recommended to use a SIM card with subscription.
This avoids possible credit balance problems. The individual responsibility for protecting the SIM card against abuse lies solely with the card owner. EASY does not accept any liability for possible damage to persons, buildings or machines, which occur due to incorrect use or from not following the details.
Prescribed Usage
Note the following:
Warning
This device and its components may only be used for the applications described in the catalog or the technical description, and only in connection with devices or components from other manufacturers which have been approved or recommended by EASY. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance.
Trademarks
All names identified by x-Messenger are registered trademarks of the EASY. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Copyright rievtech 2015 all rights reserved
The distribution and duplication of this document or the utilization and transmission of its contents are not permitted without express written permission. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved.
Disclaim of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Additional support
We take pride in answering your question as soon as we can:
5
Please consult our website at www.rievtech.com for your closest point of contact or email us at [email protected]
6
Contents
7
8
9
10
Chapter 1 General Introduction to x-Messenger
11
1.1 Overview
Rievtech x-Messenger SMS/GSM/GPRS Micro-PLC with built-in GSM modem is a device dedicated for remote monitoring, diagnostics and control of objects via short text messages (SMS) , E-mail or CLIP calls.
Configurable messages sent from the device with static (text) or dynamic (text and measured values) content are a convenient way of passing important information to the monitoring center, or directly to the defined phone numbers. SMS messages sending or Call-out can be triggered by change of binary input state, reaching alarm thresholds, marker state change, counters and clocks. Industrial design, practical set of I/O resources, easy to use configuration software tools and direct connection of sensors lowers the cost of building system. There are 4 optional (0...10V DC) signal inputs or 2 (0/4…20mA) inputs built-in the CPU. So, it can work with humidity sensors, water level sensor, pressure transducers, flow sensors, smoke, gas, motion, shock and noise detectors, etc.
The device’s own phone book saves up to 50 mobile phone numbers of the receivers.
The programming of the x-Messenger is carried out with the eSmsConfig. Two programming modes are available-standard and customized mode. All the settings can be configured very easy and without special knowledge of any programming language in standard mode. In this way the settings can be configured conveniently, flexibly and easily. Additional, Customized mode is supplied to users who are familiar with the logic boxes of Boolean algebra, and moreover complex control, logic, timer, counter, analog math etc would be needed for their systems.
*GSM network: 850MHz, 900MHz, 1800MHz, 1900MHz (Quad-band GSM module inside)
1.2 Highlight feature
Support Quad-band 850/900/1800/1900 MHz frequency
12
Change the bit flag status and register value in the program via SMS
Max. 64 different short messages and voice alarms
Max. 70 Unicode Characters in one short message
Time-based and event-based SMS, Call-IN, Call-Out, Ring.
Email alarm
IO status ,alarming message includes counters, analog values can be directly sent to Users
GPRS optional (Wireless downloading/uploading configuration or monitoring)
4 lines, 16-character per line, backlight display& keypad optional.
Standard Modbus RTU/ASCII/TCP communication protocol supported
It’s optional for x-Messenger to act as slave or master in certain Modbus communication network.
Access to internal resources with standard MODBBUS ACSII/RTU/TCP
Expandable up to 8 linked IO expansion modules reaching 40DI/36DO,36AI/36DO in maximum
1 RS232(ELC-RS232 cable is required),1RS485 port(RS485 module is required)
Optional Ethernet Interface
Optional Wifi Interface
Multiple channels analog inputs available with DC 0-10V signal, PT100 signal& 0/4….20mA.
Default Real Time Clock (RTC)
Backup at Real Time Clock (RTC) at 25 °C:20 days
Two channels high-speed counting(60KHz)
Retentive memory capability
Power supply 12/24V DC, 110/240V AC
RS232 communication download cable with photo-electricity isolation
USB communication download cable with photo-electricity isolation
Mounting via modular 35mm DIN rail or screw fixed mounting plate
On-line monitor& Off-simulation by PC
Pre-configured standard functions, e.g. on/ off-delays, pulse relay , counters ,watchdog function PI controller etc..
Logic functions-AND, OR, NOT, XOR……
Standard configure soft& Customized soft(Function block diagram)
Local and remote (Via GPRS/Ethernet) configuration ,programming and firmware update
Data logging (ELC-MEMORY is required)
Chapter 2 Applications
13
2.1 Application overview
Heating control
Pump control
Irrigation installations
Alarm transmission
Level monitoring
Temperature monitoring
Pressure monitoring
Valve control
Voltage monitoring
Building Automation
Factory Automation
Machine Automation
Remote Maintenance
Remote diagnosis
Testing Equipment
HVAC & Refrigeration
Gaming Machine
2.2 Application architecture
Application 1: Signal Alarm and SMS Communication
14
Application 2: Home Security
Application 3: Remote monitoring of product level in a tank
15
Application 4: Water Pressure Gauge, Fluid Gauge
Application 5: equipment
Data Centre, Power substation, Machinery plant unattended, Sites with expensive
Application 6: Freezer Warehouse, Walk-in Cold Room, Medical Storage, Data Centre, Power substation,
16
Laboratory
Application 7 Vending/Gaming Machine Monitoring & Reporting System
Application 8 Bridge Alarm System
Application 9 Farmland Sprinkler System
17
Chapter 3 Hardware models and resources
3.1 Naming Rules of EXM Series
EXM : series name
1. Points of total IOs
2. Power Supply ( DC 12~24V, AC 110~240V )
3. Digital/Analog( D :digital,DA : digital &analog configurable, DAI: digital,(0…10V)&(0/4…20mA))
4. Output type(R :Relay, TN : transistor(PNP type), RT: Relay and transistor)
5. Special function ( N :Ethernet access WIFI: With Wifi connectivity but no GSM/GPRS; GWIFI: With Wifi connectivity and GSM/GPRS; V:Voice function)
3.2 Hardware model selection
x-Messenger (SMS Micro PLC) Model Selection chart (excluding extension and accessories)
18
Model
Supply Voltage
Inputs
Analog Input signal
Outputs
High Speed Count(I7,I8)
EXM-8AC-R-HMI
110~240VAC
6 digital
No
2 relay(10A)
No
EXM-12DC-DA-R-HMI
DC 12-24V
4 digital/analog+4 digital
4 DC (0..10V)
4 relay(10A)
(I7,I8)60kHz
EXM-12DC-DA-R-N-HMI
DC 12-24V
4 digital/analog+4 digital
4 DC (0..10V)
4 relay(10A)
(I7,I8)60kHz
SMS
GPRS
Ethernet
Data logging
No
Yes (64 different short message configuration)
Yes
No Yes
Optional(Optional accessory: ELC-MEMORY required)
Interface 1 RS232(ELC-RS232 cable is required) & 1 RS485(RS485 module is required)
Communication protocol Modbus RTU&ASCII Modbus RTU&ASCII Modbus RTU /ASCII /TCP
RTC Yes
LCD display with keypad
Alarming mode output control mode
Programming
Yes
SMS, Ring
SMS , Call-In, Logic program control
Standard config soft& Customized soft(Function block diagram)
Yes(can send email out)
Model
Supply Voltage
Inputs
Analog Input signal
Outputs
High Speed Count(I7,I8)
EXM-8DC-PT100-R-HMI EXM-12DC-DAI-R-HMI
110~240VAC
2 digital
2 PT100(-50--200℃)
EXM-12DC-DA-R-VN-HMI
DC 12-24V DC 12-24V
2 digital/analog+2 analog+4 digital 4 digital/analog+4 digital
4 relay(10A)
No
2 DC (0..10V)+2(0/4...20mA)
4 relay(10A)
(I7,I8)60kHz
4 DC (0..10V)
4 relay(10A)
(I7,I8)60kHz
SMS
GPRS
Yes (64 different short message configuration)
Yes
Ethernet
Data logging
No No Yes
Optional(Optional accessory: ELC-MEMORY required)
Interface 1 RS232(ELC-RS232 cable is required) & 1 RS485(RS485 module is required)
Communication protocol Modbus RTU&ASCII Modbus RTU&ASCII Modbus RTU /ASCII /TCP
RTC
LCD display with keypad
Alarming mode
Yes
Yes
SMS, Ring output control mode
Programming
SMS , Call-In, Logic program control
Standard config soft& Customized soft(Function block diagram)
Yes(can send email out)
19
Note: A. RS485 port can be used as either expansion or communication port, while serving as communication port, EXM-E-RS485 communication module would be required as such port is not photo electricity-isolated.
Model
Supply Voltage
Inputs
Analog Input signal
Outputs
High Speed Count(I7,I8)
EXM-12DC-DA-RT-WIFI
DC 12-24V
EXM-12DC-DA-RT-GWIFI
DC 12-24V
4 digital/analog+4 digital
4 DC (0..10V)
2 relay(10A) +2 Transistor(0.3A)
(I7,I8)60kHz
SMS
GPRS
Wifi interface
No
No
Yes
Yes (64 different short message configuration)
Yes
Yes
Ethernet
Data logging
Yes Yes
Optional(Optional accessory: ELC-MEMORY required)
Interface
Communication protocol Modbus RTU&ASCII/TCP
1 RS232 & 1 RS485
Modbus RTU /ASCII /TCP
RTC
LCD display with keypad
Yes
Yes
Alarming mode output control mode
Programming
No
Logic program control
No
SMS, Ring
SMS , Call-In, Logic program control
Standard config soft& Customized soft(Function block diagram)
Yes(can send email out)
3.3 Resources
3.3.1 GSM /GPRS
module
built- in
Each x-Messenger CPU integrates an industry Quad-band GSM module inside. The x-Messenger can work under the following GSM networks: 850MHz, 900MHz, 1800MHz, 1900MHz and will search these frequency bands automatically.
Note: A. all the x-Messenger CPUs support the GSM function except the EXM-12DC-DA-RT-WIFI.
20
3.3.1.1
How to establish the connection between x-Messenger and PC via GPRS?
A. Here under is GPRS network connection’s sketch map: x-Messenger CPU(EXM) shall work as client at Internet and PC shall act as SERVER . Meanwhile, Internet service provider would automatically assign one dynamic IP address to SIM card inserted into the x-Messenger CPU(EXM).
B. Prior to establishing GPRS connection, these two tasks listed at below shall be performed.
1. Internet Address Disposal
User must apply for one static IP address from their local internet service provider( Such static IP address shall be unique on earth), in this case, after successful connection setup from Router to
Internet, such static IP address shall be automatically designated to user’s Router. User might consult their local internet service provider for more detailed information. However, if one unique static IP address is already available, please go to the next step.
21
2. LAN Address Disposal
User shall assign x-Messenger CPU’s communication port for GPRS to IP address of server PC. e.g. “5002” is just x-Messenger CPU’s communication port for GPRS, and “5001” had been assigned to computer 1 as well, further let’s suppose 192.168.0.119 is just IP address for server PC(computer1, in above sketch map), then
Port “5002” shall be assigned to 192.168.0.119 in Router’s configuration.
In addition, the said communication port refers to the one to be configured via eSmsConfig, furthermore, such configuration would be downloaded to x-Messenger CPU.
Click the menu “SMS->Set GPRS params” to set the server port number.
Please note that PORT’s assigning method is subject to various routers, hence, user shall consult your local router suppliers for specific assigning method.
For instance, if the static IP address user had applied is 221.226.189.74, then such IP address shall be treated as server address to be connected by all x-Messenger CPUs(EXM) involved in the network. Please
22
take a look at below demonstration configure as example for your better understanding.
C. Hereunder is a demonstration example illustrating GPRS connection establishment between remote x-Messenger and eSmsConfig installed in the server PC(or other server software).
Step1: A static IP address shall be required, for example, it is 221.226.189.74, and you can refer to the forementioned A&B for the detailed explanation on static IP address. Meanwhile, the eSmsConfig installed in the server PC works as the server.
Step2: Open the software eSmsConfig and set up a connection between x-Messenger and eSmsConfig via
USB/RS232 mode.
Step3:To confirm the connection is established successfully, you can read the RTC from the x-Messenger.
Step4: Click the menu “SMS->Set GPRS params”.
Step5: Configure the APN based on your SIM card and then click "Write" to download the configuration into x-Messenger.
23
Fig 3
You can set the IP address and the port number in the above dialog box. (It is based on your server(fixed
IP address).
Step6: Click the “ ” button. After set successfully, you can establish the connection via GPRS between x-Messenger and eSmsConfig (your server).
Step7: Open the COM port again and select the GPRS option
Set the port number “5002” ( it is the same as the you set in the Fig 3), and click “Start server” and then the IP address of x-Messenger will be displayed in the “EXM”. If you choose the “with Name” option, then
24
the device name and the IP address will displayed.
Step8: After the connection is established successfully, Program download/upload and data remote monitoring can be realized in a wireless way all over the world.
Application:
1.x-Messenger is client with a dynamic IP address,(SIM card)
2.Server software ( With a static IP address)
Option A:
The server software can ask for some information such as temperature(analog inputs), level (digital inputs) from the remote station, also it can remotely control items such as a valve with a standard command
(MODBUS TCP command). We are not supplying server software, which is available from other sources. This is only to use the GPRS function.
The data transmission after the GPRS connection has been established, the communication protocol is achieved using standard Modbus TCP. For the detailed information about the modbus protocol and memory map/ register addresses of x-Messenger, please read the "Modbus TCP communication protocol" from our side/website.
You can use our free of charge SCADA(easyScada) to communicate with EXM by GPRS(You can refer to the
SCADA user instruction about how to make the connection).
Option B: x-Messenger can upload the digital inputs/outputs, analog inputs to the server(User can make their own server software based on the modbus tcp protocol, or use our free of charge easyScada). There are 2 GPRS function blocks available. Please see the chapter 7.2.14 &7.2.15 for a detailed description.
25
3.3.1.2 E-mail and how to set?
This chapter is only available under the customized programming mode!
Step A: Enable the GPRS function via the menu SMS->Set GPRS param.(The communication port must be opened, and then this step would be available.)
Configure the APN(Access Point Name) based on your SIM card and then click "Write" to download the configuration into x-Messenger.
When you want to send email out, the option “Connect to ethernet when power on” option is not important, you can let it without ticked up.
Step B: Set up your email parameters
Click menu SMS->Set email params
26
Click "Write" button to download the parameters into x-Messenger
The receiver email address and the alarm text can be edited in the "sms message output" function block.
27
1. Set the email address of the receivers, there are 3 receiver E-mail addresses can be set.
2. E-mail caption configuration box.
3. Email contents can be text message and parameters message
Text message can be edit in the message editor( 4 in the above figure)
Parameters message including such as IO status, analog IO values, kinds of parameters(counters, timers,
RTC etc).
3.3.1.3 How to change the register value(F,Q,AQ,AF,REG) or phonebook via SMS
Send an SMS message formatted like the example below
##**
28
AF1=2;
AQ02=100;
Q01=1;Q12=0;
F1=1;F2=0;
AM1=10;
REG1=100;
REG100=300;
TEL,B002,1,B002,2,B003,1,B003,5:13851448223;
RTC=89-01-09,01:32:09,0;
Message Parameters :
Start characters: ##** (These 4 characters must be included at the start of your message)
End character: ; (This symbol must be used to terminate each line of your message )
Parameters:
AF1= 2; This is to change the AF value, you can input the different numbers, for example AF=200;
AQ02=100; This is to change the AQ value, you can input the different analog outputs, for example
AQ21=200;
Q01=1;Q12=0; This is to change the the I/O output status, for example Q22=1;
F1=1;F2=0; This is to change the FLAG output status,for example F22=1;
AM1=10; This is to change the AM value, you can input the different numbers, for example AM30=200;
REG1=100;
REG100=300; This is to change the REG value, you can input the different numbers, for example
REG2=200; This can be used to change the current value of function blocks, such as counters.
TEL,B002,1:13851448223;
This is to change receiver for the sms message output block.
29
If you send the short message contents as the
##**
TEL,B002,1,B002,2,B003,1,B003,5:13851428396;
,consequently, the receiver1 & receiver2 of the B002 function block and receiver1 & receiver5 of B003 shall turn to 13851428396.
30
How to modify the all the receiver number of sms message output blocks in the program ?
If you want to modify the receiver number in all the sms message output block, you can edit the short message format like this:
##**
ALL:TELQ,1:13851448223;
This is to change receiver 1 for all the sms message output block in the program.
TELQ, means the “SMS message output block”
1 means the receiver 1 in the block, this number can be 1 to 5.
13851448223; It is the phone number which will be set into the receiver.
Modify the telephone number in the sms message input like this:
Edit short message :
##**
Msg,I01,1,I01,2,I01,3,I01,4,I01,5,I02,1,I02,5,I03,2,I03,4,I03,5:10987654321;
And then the phone number in the sms message input shall be changed with 10987654321.
31
MsgI01:
MsgI02:
32
MsgI03:
How to modify the all the receiver number of sms message input blocks in the program ?
If you want to modify the receiver number in all the sms message input block, you can edit the short message format like this:
##**
ALL:TELI,1:13851448223;
This is to change receiver 1 for all the sms message input block in the program.
TELI, means the “SMS message input block”
1 means the receiver 1 in the block, this number can be 1 to 5.
13851448223; It is the phone number which will be set into the receiver.
RTC=89-01-09,01:32:09,0;
This is used to change the Real time clock of x-Messenger, Year-month-day,hour:minute:second,week;
33
0: Sunday
1: Monday…..
Note: The parameters can include one or more items as above shows, for example, you want to modify the phone number, you only need to edit message as follows:
##**
Msg,I01,1,I01,2,I01,3,I01,4,I01,5,I02,1,I02,5,I03,2,I03,4,I03,5:10987654321;
This function also can be used between two individual x-Messengers CPU.
For example:
GMS
Locally Remote
The Analog input1 & Analog input2 of remote station can be sent to the local one by means of SMS.
The SMS message can be configured like this:
This parameter can be configured in the sms message output block.
34
3.3.1.4 How to modify the PIN via SMS
Note: 1.The PIN code of SIM card must be set on cell-phone, here PIN is only for the x-Messenger.
2.Only when the PIN you set into x-Messenger is the same as the one of SIM CARD, and then the SIM
CARD would be in service in normal.
The PIN of x-Messenger can be set in the eSmsConfig from the menu “SMS->General Settings”
Send an SMS message formatted like the example below
##**
PIN:1234;
Message Parameters :
Start characters: ##** (These 4 characters must be included at the start of your message)
End character: ; (This symbol must be used to terminate each line of your message )
Parameters:
PIN:1234;
PIN code must be 4 digit Arabic numerals(0--9).
35
3.3.1.5 How to modify the GPRS Parameters and Email parameters via SMS
1. GPRS parameters and modification via SMS.
GPRS parameters can be viewed from menu “SMS-> Set SMS parameters”
Send an SMS message formatted like the example below
##**
PGPRS:
TIMEOUT"60",
IPORDOMAIN"0",
POWCONNECT"0",
APN"CMNET",
TADR"221.226.189.74",
TPORT"5005",
SNUMB"12345678",
DOMAIN"www.wyl.com";
Message Parameters :
Start characters: ##** (These 4 characters must be included at the start of your message)
36
Parameters interval characters: , (This symbol must be used to differentiate each parameter of your message )
End character: ; (This symbol must be used to terminate each line of your message )
Parameters:
PGPRS : (This head means the below contents is used to modify the GPRS parameters)
TIMEOUT"60", (This is to change the time out period, the unit is “second” and the minimum value is
30, if you set the value less than 30, x-Messenger would set 30 automatic value)
IPORDOMAIN"0", This is to change network mode.
IPORDOMAIN"0", means IP address option shall be ticked:
And if IPORDOMAIN"1", means Domain Name option shall be ticked.
POWCONNECT"0", This command is used to change the option “Connect to ethernet when power on”, if the contents is POWCONNECT"0", this option shall be un-ticked:
And if the contents is POWCONNECT"1", this option shall be ticked:
APN"CMNET", This command is used to modify the APN(Access Point Name).
37
TADR"221.226.189.74", This command is used to modify the Target IP address
TPORT"5005", This command is used to modify the Port number for target network.
SNUMB"12345678", This command is used to modify the Device Name(serial number) 8 characters in maximum.
DOMAIN"www.wyl.com"; This command is used to modify the Domain name.
2.Email parameters and modifications via SMS.
Email parameters can be viewed from menu “SMS-> Set email params”
38
Send an SMS message formatted like the example below
##**
PEMAIL:
SMTPADR"smtp.163.com",
SMTPPORT"25",
SMTPUSER"[email protected]",
SMTPPWD"12345678",
SENDNAME"chen",
SENDEMAIL"[email protected]";
Message Parameters :
Start characters: ##** (These 4 characters must be included at the start of your message)
Parameters interval characters: , (This symbol must be used to differentiate each parameter of your message )
End character: ; (This symbol must be used to terminate each line of your message )
Parameters:
PEMAIL : (This head means the below contents is used to modify the email parameters)
SMTPADR"smtp.163.com", This command is used to modify the SMTP for your Email box
SMTPPORT"25", This command is used to modify the SMTP for your Email box.
39
SMTPUSER"[email protected]", This command is used to modify the user name for your Email box.
SMTPPWD"12345678", This command is used to modify the password for your Email box.
SENDNAME"chen", This command is used to modify the sender name for the Email.
SENDEMAIL"[email protected]"; This command is used to modify the email address for the sender..
You are allowed to send a SMS to check the settings as follows:
##**
RPGPRS;
RPEMAIL;
Parameters
RPGPRS; This command is used to check the settings of GPRS. GPRS information would be sent to the user who want to check.
RPEMAIL; This command is used to check the settings of GPRS. GPRS information would be sent to the user who want to check.
3.3.1.6 How to modify the email address of the receiver via SMS?
Send an SMS message formatted like the example below
##**
EML,B002,1,B002,2,B003,1,B003,3:[email protected];
Message Parameters :
Start characters: ##** (These 4 characters must be included at the start of your message)
End character: ; (This symbol must be used to terminate each line of your message )
40
Parameters:
EML,B002,1,B002,2,B003,1,B003,3:[email protected]; The receiver 1, receiver2 of B002 block and receiver1, receiver3 of B003 block would be modified to “[email protected]”.
B002(Sms Message Output):
B003(Sms Message Output):
How to modify the all the receiver E-mail address of sms message output blocks in the program ?
41
If you want to modify the receiver E-mail address in all the sms message input block, you can edit the short message format like this:
##**
ALL:EMALQ,1:[email protected];
This is to change receiver 1 for all the sms message output block in the program.
EMALQ, means the the receiver email address in the sms message output block.
1 means the receiver 1 in the block, this number can be 1 to 3.
[email protected]; It is the phone number which will be set into the receiver.
3.3.2 Voice alarm
With '-v" series x-Messenger CPU means the voice function is available. Voice function includes voice alarm, telephone control function and automatic dialing function. Voice alarm can be realized via the audio jack (see A below) or the built in speaker in certain models (see B below), alarm message also can be got after you hold the call from x-Messenger and press the button on your phone according the prompt voice. Telephone control function means you can control the x-Messenger with your phone remotely.
Structure of the voice interface
A
With HMI model(-v)
A.Voice module on-line recording audio input port &Audio output port (to be connected with the microphone
(Input) or speaker (Output) ) Applied to both with HMI model and without HMI model.
42
How to record the voice section into x-Messenger?
Before recording, equip your PC with voice card , otherwise the recording can’t be carried out.
Step A.
Establish the connection between x-Messenger programming port and the COM port of your PC(RS232/USB) with the download cable(ELC-USB,ELC-RS232, EXM-USB-B ) and the connection between the audio input interface of x-Messenger and the audio output interface of your PC with audio wire(see below figure).
Free audio wire accessory, to connect the voice audio input and PC audio output.
Step B. Open the "eSmsConfig" software and establish the communication (Select the correct com port you are using, and connect to EXM).
43
Step C. Download voice section.
Click menu Tool-> Record
Click "Hardware Detect" button.
44
1. Sound format selection:
There are 3 options : 4m ,6m and 8m.
In total length range of the recording, the recording of the voice module can be divided into 0-99 sections .
(Note: Option1: 4 minutes, the voice sampling frequency is 3.4 K Hz, Option2: 6 minutes, sampling frequency is 2.3 KH z, 8 minutes sampling frequency is 1.7KHz, if you want better sound quality, use a higher sampling frequency. )
2. Voice section displayed, you can add ,delete,and clear all the file with the relevant button. The voice file format is ".wav" Any other format file is unavailable.
3. Erase the voice section in x-Messenger.
Erase all the voice sections by clicking the "Erase all" button.
Erase one of the voice section by clicking the "Erase one" button. You can input the voice section number in the dialog box which you want to delete.
4. Record all the voice section by click "Start".( While the "Start button" is pressed down, the voice would be played and at the same time x-Messenger shall record one by one.)
Note: The audio wire must be connected between x-Messenger and PC, otherwise , although the voice has been displayed, x-Messenger cannot record any voice section. In other words, the voice section is downloaded from PC to x-Messenger by the audio wire, not via the download cable.
6. File progress: It is showing you the voice section "playing progress".
7. Memory progress: It is showing you the voice memory space status. Total memory space can be used to store up to 4, 6 or 8 minutes voice section.
Note: 4 minutes format with the best voice quality, and 8 minutes format with the worst voice quality.
8.Hardware play: You can play any one of the voice sections in the x-Messenger(0-99 section)
45
Relative voice function block description
Sound play
Description of function
The relative voice message would be played if this block were enabled. There are 3 optional ways for sound playing:A. built-in speaker B. External speaker C. Phone alarm voice
Connection
Input En
Output Q
Description
You enable/disable the sound play with the signal at input En.
Q switches on if sound play were enabled and the sound section had been played more than 1 time successfully.
Property dialog box description
A. Interior speaker
This option is for the built-in speaker model.(Only applied to "....-v-cap" model, this type is discontinued)
46
B.External Speaker
External acoustics
Sound message :
Voice section selection.
Sound message: 0 means the voice section 0 from the record manage dialog box.
47
Voice alarming via phone
In your program, you must use the "sms message output'' function block(Refer to the relative chapter in the user manual).
Select the "Sms Dial" option, you can choose the receiver phone number from the Phone book. If this block were enabled, x-Messenger would dial to the corresponding user's cell phone. And users can check the alarm voice according to the broadcast contents.If there is no "sound play" function block enabled, x-Messenger would not broadcast alarm voice section.
How to realize the 'telephone control function' ?
When a user dials x-Messenger, x-Messenger will answer the telephone automatically and broadcast-Please enter the password for confirmation, then the user enters the x-Messenger password.
A. If the entered password is correct, x-Messenger will then broadcast-Correct password. Please enter
the control code to control. Then the user can control the equipment by the use of the telephone key.
Note: This function is available only if you put the sms message input function block in your programme and select the "Incoming Call and Answer call" box.
48
Telephone key
Description of function
There are 9 bit flags based on the 1--9 key of the telephone. After you enter into the telephone control mode, and enter # 0, the P0 block would give off one trigger. If you enter # 8, the P8 would give one trigger
Operation Instructions of the Voice function for x-Messenger
1.The first five sections (section 0, section 1, section 2, section 3, section 4) are for the voice system. Users cannot record the five sections randomly.
2.Section 5 to section 99 of the voice module are the voice sections for users programming and can be used randomly. However, users must start recording from section 0 while the functions of section 0 to section 4 are fixed by the system.
Functions from section 0 to section 4 are as follows:
Section 0: When dialing out through the “sms message input/output” block, it will broadcast this section
“Please enter No. 0 key and receive the information”. (When recording, users must record this voice contents “Please enter No. 0 key and receive the information”)
Section 1: the voice prompt for confirming the user status. It will be broadcasted when x-Messenger system number has been dialed or x-Messenger dialed out to configured user. Normal broadcasting can be carried out with this section.
Section 2: the voice prompt for the correct password. It will be broadcasted when the correct password is used. Normal broadcasting can be carried out with this section.
49
Section 3: the voice prompt for the wrong password. It will be broadcasted when the wrong password is used. Normal broadcasting can be carried out with this section.
Section 4: the voice prompt for dialing to an external telephone. It will be broadcasted when x-Messenger dials an external telephone. Normal broadcasting can be carried out with this section.
3.Usage of the five special sections
For example: users can use the five message sections as follows:
Step I:
Record section 0 as Please enter No. 0 key and receive the information.
Record section 1 as Please enter the password for confirmation.
Record section 2 as Correct password. Please enter the control code to control.
Record section 3 as Wrong password. Please re-enter.
Record section 4 as Emergency. Please enter the password to control.
Record section 5 as Emergency. Gas leakage.
Step II:
When a user dials x-Messenger, x-Messenger will answer the telephone automatically and broadcast-Please enter the password for confirmation, then the user enters the x-Messenger password.
A. If the entered password is correct, x-Messenger will then broadcast-Correct password.
Please enter the control code to control. Then the user can control the equipment by the use of the telephone.
B.If the entered password is not correct, the x-Messenger will broadcast-Wrong password.
Please re-enter. Then the system will repeatedly broadcast-Please enter the password for confirmation.
Step III:
When x-Messenger dials an external telephone number(pre-set in sms message output block of your program), it will broadcast the pre-set message such as section 5-Emergency, Gas leakage. Together with section 4-Emergency, Please enter the password to control.
A. When the user enters the correct password, the voice system will broadcast section 2-Correct password. Please enter the control code to control and then repeatedly broadcast section 5-Emergency, Gas leakage. At this time the user can take control of connected equipment in real time by the use of the telephone.
B.When the user enters a wrong password, the voice system will broadcast section
3-Wrong password. Please re-enter. And then it will broadcast section 4 and section
5 repeatedly.
Password protection is according to the x-Messenger settings, if there is no password for x-Messenger, it will broadcast the alarm voice without section 2.
Notes:
1. x-Messenger dialing an external telephone, if there is no answer or a password is not entered within the
50
connection set point time , the x-Messenger voice system will stop dialing and cease to broadcast the voice message. The x-Messenger will then redial automatically according to the settings in the "Sms message output block.
2. User must enter a # before entering the password. The broadcasting will then stop and the user should enter a four-digit password within 10 seconds. If the user fails to enter the password, the x-Messenger will re-broadcast the voice prompt. The user must then enter # first and then enter the password. If the user needs to enter the password again, the procedure needs to be repeated. That is to say that every time the user needs to enter the password , he must enter a # first and enter a four-digit password within 10 seconds after the voice has stopped.
3. When the user has entered the correct password, the voice system will broadcast section 2-Correct password. Please enter the control code to control and then the user can do the following operation. If the password is wrong, the voice system will broadcast section 3-Wrong password. Please re-enter. The user can only enter the wrong password three times. If the user enters the wrong password for a fourth time , x-Messenger will hang up the telephone and stop broadcasting. If the alarm status still exists, the voice system will dial automatically, for alarm purposes, every 40 seconds.
4. When the alarm status exists, x-Messenger will broadcast the alarm voice repeatedly. It can be stopped by the use of the control function within the program.
5.
For the first time set-up, before recording, the user must delete existing messages before . Otherwise the recorded voice may be lost. As to the recorded voice messages, user may delete or modify randomly the voice message in them. And it has no effect on the other voice messages. As for the details, it is explained in the voice recording explanation.
51
Examples of Voice Module
Preparations:
1.Connect the x-Messenger to your PC as detailed above.
2.Record message. (The first five messages must be recorded and the other four messages recorded according to the user's needs.
)
Message 0: Press key #0 and listen to the message.
Message 1: Please enter the password.
Message 2: Correct password.
Message 3: Wrong password. Please re-enter.
Message 4: Run normal. No alarming.
Message 5: The door is not closed. Please handle urgently.
Message 6: Thief. Please catch. Address: No. 28, ningshuang Road.
3.Set the telephone.
First you need edit the phone book and select the phone number in the sms message input/output.
Second:
SIM card in x-Messenger is No.1234567
Set the user1 phone No. 11111111
Set the user2 phone No. 22222222
Set the user3 phone No. 33333333
Set the user4 phone No. 44444444
Example 1
Check if x-Messenger system running normally and retrieve unit information. The user himself check the system, the password is set. Only the password is correct, the system information can be learned. So set the password via the panel key or software.
52
When programming, requirements are as follows:
① Correct password.
② Set related function block.
Program is as follows:
MsgI01 "sms message input' function block property box settings: x-Messenger can only answer a call from user1,user2,user3,user4 phone number, other users calls cannot be answered.
B001 "Sound play" function block property settings
53
Actual Demonstration:
① Dial the telephone No. 1234567 of the voice module from user1--4..
② It will play Message 1 “Please enter the password.”
③ Enter the preset password via the telephone keys.
A. Correct password.
It will play Message 2 “Correct password.” If I1 is not triggered, it will play
Message 4 “Run normally. No alarm.” After playing, if user doesn’t hang up the telephone, it will play Message 4 repeatedly.
B. Wrong password.
It will play Message 3 “Wrong password. Please re-enter.” and then Message 1
“Please enter the password.”
Example 2 x-Messenger system detects there is something abnormal and prompt the user. Under this situation, the x-Messenger is needed to set password to avoid the stranger knowing the prompting contents. Password can be set via the panel key or via the menu in eSmsConfig software.
Program is as follows:
54
B002 "sms message output' function block settings:
Actual Demonstration:
① x-Messenger system detects that the door is not closed. (I1 connected to the switch testing the door status.) I1 is triggered and B002 is activated by I1. Then the x-Messenger will dial user1 11111111 the preset telephone of B002.
② When the user picks up the telephone, he will hear that “Please press Key #0 and listen to the message.”
When the user presses Key #0, it will play Message 1 “Please enter the password.”
55
In this example, when the voice module dials the preset telephone, if the user1 doesn’t pick up the telephone, x-Messenger would dial user2 and user3 according to the confirmation settings(waiting time and loops)
3.3.3
Ethernet Interface
This chapter is applied to the CPU built-in the Ethernet module, the model with “-N”.
If the application requires a system where more than one CPU is required and these CPUs have to communicate, each CPU will be connected over an Ethernet Module box to the Ethernet. The project downand upload to and from the CPUs and the communication between the CPUs happens over the Ethernet network. Furthermore the visualization of the whole system is possible and easy to realize by a personal computer.
56
Software part:
Device IP factory setting
The default IP address of Ethernet module is:192.168.0.250
Network segment check of PC and Ethernet module’s
Users need ensure that PC has Ethernet cards,and that the network settings of PC and Ethernet module’s must keep in the same network segment before establishing communication between PC and Ethernet module.
The Ethernet module has a factory setting IP(192.168.0.250) and network mask(255.255.255.0). Users can process as shown in Figure 4.3 to check whether the Ethernet module and PC in the same network segment. If in the same network segment, then congratulations to you, and you do not have to read the following network setting contents. If it is different, then the following settings is very important to you.
Above contents is used to tell you how to make the user’s PC with the ethernet module in the same network segment.
First part: set or modify IP address, port number with “DeviceManager2.00” software.
How to configure Ethernet module built-in EXM address?
Start Ethernet module IP address configuration software.
Step one: Double click the file “DeviceManager” in CD and then the following contents will pop out:
57
Step two: Select “DeviceManagement.exe” file, and start it with double-click the left key of your mouse.
In order to enable your Ethernet module to link to Ethernet, you are required to connect the LAN port of the
58
CPU to your computer by net router. You are allowed to connect the LAN port of the CPU to Ethernet directly by common net cable. Hereunder let’s take computer as an example:
Connect diagram:
You are required to set as following way, otherwise the Ethernet module may fail to work , please take some time to study the below instruction carefully :
Power on CPU and click to search Ethernet module. At the same time the searching
Process will be showing. In the search window, we can see the search module, and the corresponding MAC address and IP Address.
59
Double-click the device in the list of equipment; or select equipment items, click the toolbar button
Input the username and password to login. The default is Username: admin; Password is admin.
If the username and the password are both correct, you can click the button. And the
60
configuration dialog box would pop out.
Basic Settings:
You can rename the Device name, default is NB-L
After you click the “OK” button, the settings in the current dialog box would be set into the CPU.
61
Network settings:
You can view the network parameters in such table.
62
Serial Settings:
This item is very important, you must set as the above figure shows
Note: Baudrate can be set “4800” ,”9600”,”19200” and the corresponding communication port must be set the same as baudrate , namely , the COM3 of CPU. The default baudrate is 9600 in CPU.
63
Connection settings:
ELC/EXM-12DC-DA-R-N /ELC-12AC-R-N can work as either server or client.
Net Protocol: TCP
Worked As: Server/Client
Remote Host: The remote PC IP address (while working as client, CPU will automatically get connected to such remote host.)
Active connect : Auto Start
Remote Port: the remote port (while working as client, CPU will get connected to remote host with such port.)
Local Port: the local port (while working as server, the client shall be connected with the CPU
64
Password setting
Password can be changed in such dialog box. Password is required for accessing the Ethernet port. You must enter at least one character or number.
65
Apply Settings/Reset
Merely “Save and reboot “ option can be selected among those options shown in above page.
Export you settings:
Click to export the settings
66
The configuration would be saved as a .xml file.
You also can import the existed configuration by the menu Tools->Import Config
67
Second part: Communication and monitor with eSmsConfig.
1.Connect the ELC-12DC-DA-R-N as the first part, and configure as the first part.
2. Here are two options to open “COM PORT”:
A. click symbol B. select menu Tools->Configuration
Option 1: Ethernet module in CPU works under TCP client mode, eSmsConfig software acting as server .
68
3.
Select “Ethernet” option
4. To search “PLC’s IP” by clicking “Search” button
69
eSmsConfig Com port setting dialog box LAN port setting in Device manager
Port number and PLC’s IP pre-configure in Device manager shall be configured as above figure shows
Notes:
1.The remote host IP address is the same as that of the PC in which the eSmsConfig being installed .
2.Modbus Type in x-Messenger shall be MODBUS TCP
3. Active Connect must be “AutoStart” in device manager.
5.
Click "Connect to PLC" button, and then the Ethernet module and PC will be linked.
After the EXM CPU and PC being linked, many features can come true, e.g. downloading user program into x-Messenger CPU module , uploading program into PC and online monitor (monitor real time status of x-Messenger IO)can be done, herewith Ethernet module just plays a role of ELC-RS232/USB cable.
A . Upload program: click
B. Download program: click
C. Monitor program run status: click
Option 2: EXM CPU work under TCP serve mode, xLogicsoft software acting as Client.
70
6.
Click "Connect to PLC" button, and then the Ethernet module and PC will be linked.
How to establish the communication between EXM CPUs via Ethernet ?
Hardware connection.
71
Step A.
First you need use the device manger to configure the LAN connection.
Example:
Master PLC works as server. Its IP address is 192.168.0.16 and the local port shall be set as 5001.
As below configure shows :
Work as: server
Local port: 5001
72
The items with red circle marked must be the same as the above figure.
Slave 1 settings:
IP address is 192.168.0.17
Work as : Client
Remote Host: 192.168.0.16
Remote port: 5001
73
The items with red circle marked must be the same as the above figure.
PLC address need be changed to 1 (default is 1). Change the CPU address with the panel key
Press Press ,and then press
Press with UP or DOWN button and confirm with OK.
Press Change address
Slave 2 settings:
IP address is 192.168.0.18
74
Work as : Client
Remote Host: 192.168.0.16
Remote port: 5001
PLC address need be changed to 2 (default is 1). Change the CPU address with the panel key
Press Press ,and then press
Press with UP or DOWN button and confirm with OK.
Press Change address
Regarding the program. We need realize the below logic.
1.I1--I4 in master to control the Q1--Q4 in slave1&salve2, if I1 is ON in master, the corresponding Q1 in salves is ON; I2 is ON in master, the corresponding Q2 in salves is ON;....I4 is On in master, the corresponding
Q4 in salves is ON. If I1 is OFF in master, the corresponding Q1 in salves is OFF.......I4 is OFF in master, the corresponding Q4 in salves is OFF.
75
2. Read the Inputs I1--I4 status of slave 1 to control the F11--F14 in master; Read the Inputs I1--I4 status of slave 2 to control the F21--F24.
3. Read the AF1 value of slave1 to be saved in the AF1 of master; Read AF1 value of slave2 to be saved in AF2 of master.
Program in slave 1
(Note: In the program, you can put the input/output block in, but you cannot link the input pin of the output)
Program in slave 2
(Note: In the program, you can put the input/output block in, but you cannot link the input pin of the output)
Program in master
You need use the MODBUS BLOCK to realize the data transmission between master and slaves.
76
B001: Transfer the I1--I4 status from the master to the Q1-Q4 of the slave1. Setting as follows:
77
B002: Transfer the I1--IA status from the master to the Q1-QA of the slave2. Setting as follows:
78
B005: Read the I1--I4 status from the slave1 to the F11-F14 of the master. Setting as follows:
79
B006: Read the I1--IA status from the slave2 to the F21-F24 of the master. Setting as follows:
80
B009: Read the AF1 value from the slave1 to the AF1 of the master. Setting as follows:
81
B010: Read the AF1 value from the slave2 to the AF2 of the master. Setting as follows:
82
Notes:
1. When you do not use the MODBUS blocks in your program, then EXM CPU shall work as slave, in this case, you can use the SCADA or touch screen to communicate with EXM via the LAN port. However, if MODBUS
BLOCKS had been used in your program, moreover, the communication type (comm Type) is Ethernet, then
EXM can not work as slave through Ethernet port
2. In your program, if the Modbus read/write blocks would be used, then you can use the EXM as the master
CPU to communicate with the slave ( i.e. x-Messenger or the devices from other supplier which supports the standard MODBUS TCP communication protocol.) in Modbus network
3.3.4 SD card Data logging
Reserved(Currently not available) If data storage is needed use, our ELC-MEMORY is an optional accessory.(You can
83
refer to the function block “MEMORY WRITE” instruction, then you may know how to save the data into the SD card)
3.3.5 Communication Interface
1. Programming port/RS232 port(ELC-RS232 ,ELC-USB,ELC-Copier,ELC-MEMORY should be inserted in this port)
When the programming port is to be used as the standard RS232 port (D-shape 9 pin header) ,the
ELC-RS232 cable is needed. Below are the pin-outs for the RS232 connection:
3
5
PIN
2 others function
RXD
TXD
GND
NULL
2. Expansion port/RS485 ( pin definition(2X3 pin socket)
84
1------RS485 A1
6------RS485 B1
2------
3------
4------GND
5------Battery
Communication between CPU and expansion module will use pin 1, 6. This is COM1.
EXM-E-RS485 module is required when EXM-12 CPU needs to communicate with third party devices via RS485 bus and then these pins (1 and 6) will be used by EXM-E-RS485 module .This is COM1.
So if you had use any extension module with EXM-12 CPU, EXM-E-RS485 shall be unavailable.
Note: 1.The baud rates and communication mode(Modbus RTU/ASCII/TCP) of COM0, COM1 can be modified via the panel key.
2. The COM1 port also can work as the common RS485 port, when there is no expansion module in the application.
3.3.6Multiple Modbus communication protocol.
There are three optional communication protocols available. Refer to the communication protocol file for details. Following are the register addresses for the x-Messenger.
Name Code Set address method
(DECIMAL)
Data format Attribute
85
Digital quantity input switch
Block in xlogicsoft:
Type:
(1x)
4 cursors
( Cursor key)
(1x)
Coils outputs
(0x)
EXM-12
C
0~7
256~259
EXM-12 /ELC-12(CPU):
ELC12-E-8(EXT1)
ELC12-E-8(EXT2)
ELC12-E-8(EXT3)
0~7
8~15
16~23
24~31
Middle coil
(0x)
EXM-12
M
256~767
BIT R
BIT R
BIT R/W
R
86
F outputs F
EXM-12 1536~1599
BIT R/W
(0x)
Holding register(timer、 counter value)
(4x)
Analog quantity input register
REG
EXM-12
AI
EXM-12
(4x)
Analog quantity output buffer
AQ
EXM-12
0~511
LONG R/W
(1024~1279)
CPU:1024~
1031
EXT1:1032~
1039
EXT2:1040~
1047
…………
(1280~1535)
CPU:1280~1281
EXT1:1282~1283
EXT2:1284~1285
Signed short
Signed short
R
R/W
(4x)
Analog quantity buffer AM
EXM-12 1536~2074
Signed short R
(4x)
87
Analog quantity buffer
(4x)
The frequency value buffer of threshold trigger
AF
EXM-12
REG
EXM-12
3072~3135
2560~3071
Signed short R/W
Word R
(4x)
3.3.7 LCD panel instruction
1 . Display area: 4x16 characters can be displayed
2 . 4 X Function key: operate the program by pressing down these key
3 . 6x Panel key: you can modify the parameters, programming, view alarming message.
What this operate panel can do for you?
1 . Display the RUN/STOP status of the CPU
2 . Display the GSM signal strength
3 . Display or modify the Clock.
4 . Display the IO status of CPU& extensions
5 . Display all kinds registers value(AI/AO, Parameters of blocks etc)
6 . Display multiple alarming messages
7 . Modify the parameters of blocks
88
8 . Manual programming
9 . Backlight can be controlled via programming(Light on Alarm)
10 . System cover message can be customized
11 . Up to 64 different alarming messages is allowed.
12 . The CPU address can be modified
13 . Set password protection
……..
Menu shows:
89
Manual programming menu:
How to program via keypad? Please refer to the chapter 5 for more detail.
90
3.3.8 Antenna
The x-Messenger comes together with the EXM-ANT 3 meters a dhesive antenna . The location of installation must be taken into account and the right antenna has to be selected to ensure reliable connection with the network.
Following antennas is are also available for use:
A B
A. Penta-band GSM Antenna
C
B. EXM-ANT(standard accessory with x-Messenger CPU)
C. The antenna with magnetic base
D. T shape antenna
D
Note:The Penta-band GSM Antenna is not suitable for installation inside a control panel (shielding).
3.4 Structure & dimension
1. Standard EXM-12 series CPU
A. With LCD panel model
91
1. Power supply & Inputs terminals
2. Output terminals (Relay/Transistors)
3. RS232 / Programming interface (TTL signal)
4. Expansion/RS485 port
5. LCD panel (4X16 chars display & 10 panel keys)
6. GSM antenna socket
7. Socket of telephone crystal plug
8. Optional A-type USB interface
9. Mini-SD card socket
10. Audio input/output interface
11. Ethernet interface
12. SIM card holder (Under the LCD panel/ LED indicator cover)
2. Dimensions
Standard EXM CPU:
92
Chapter 4 Installing/removing EXM
4.1 DIN rail mounting
Mounting
How to mount a x-Messenger module and a expansion module onto a DIN rail:
1. Hook the x-Messenger Basic module onto the rail.
2. Push down the lower end to snap it on. The mounting interlock at the rear must engage.
3. Hook the x-Messenger expansion module onto the rail
4. Slide the module towards the left until it touches the x-Messenger CPU.
5. Push down the lower end to snap it on. The mounting interlock at the rear must engage.
6. Remove the plastic cover in the expansion port of CPU and expansion module.
7. Plus the connection bridge
93
Repeat the expansion module steps to mount further expansion modules.
Notes: 1. EXM-E extensions connect with EXM-12 CPU by EXM-CB-A connector or
EXM-CB-B connection cable (3 meters)
Removal
To remove x-Messenger:
....... if you have installed only one x-Messenger Basic:
1. Insert a screwdriver into the eyelet at the bottom of the slide interlock and move the latch downward.
2. Swing the x-Messenger Basic off the DIN rail.
....... if you have connected at least one expansion module to x-Messenger Basic:
1. Remove the connector
2. Slide the expansion module off towards the right.
3. Insert a screwdriver into the eyelet at the bottom of the slide interlock and lever it downward.
4. Swing the expansion module off the profile rail.
Repeat steps 1 to 4 for all other expansion modules.
94
4.2 Wall-mounting
For wall-mounting, first slide the mounting slides on the rear side of the devices towards the outside. You can now wall-mount x-Messenger by means of two mounting slides and two ØM4 screws (tightening torque 0.8 to 1.2 Nm).
Drilling template for wall-mounting
Before you can wall-mount x-Messenger, you need to drill holes using the template shown below.
EXM series(applied to CPU and extensions):
95
All dimensions in mm
Bore hole for Ø M4 screw, tightening torque 0.8 to 1.2 Nm
1. x-Messenger CPU
2. EXM-E series extensions
4.3 wiring EXM
Wire the x-Messenger using a screwdriver with a 3-mm blade.
You do not need wire ferrules for the terminals. You can use conductors with cross-sections of up to the following thicknesses:
1 x 2.5 mm 2
2 x 1.5 mm 2 for each second terminal chamber
Tightening torque: 0.4.. .0.5 N/m or 3. ..4 lbs/in
Note
Always cover the terminals after you have completed the in sta ll at i on . To pr o t ect x-M esseng er ad eq u at ely fr o m impermissible contact to live parts, local standards must be complied with.
4.3.1 Connecting the power supply
The EXM-8AC versions of x-Messenger are suitable for operation with rated voltages of
110 V AC and 240 V AC. The standard EXM-DC versions can be operated with a 12 or 24
VDC power supply.
Note
A power failure may cause an additional edge triggering signal.
Data of the last uninterrupted cycle are stored in x-Messenger.
To connect x-Messenger to the power supply:
96
4.3.2 Connecting x-Messenger inputs
1. Requirements
At the inputs you connect sensor elements such as: momentary switches, switches, light barriers, daylight control switches etc.
EXM-8AC EXM-12DC EXM-6DC
EXM-3DC
Signal status 0
Input current
Signal status 1
Input current
Analogue input
<0.24mA
>85VAC
Typical
NO
<1.5mA
>8VDC
Typical 3mA
AI1-AI4(0-10V DC)
97
Note:
1
. For EXM-12DC-DA Series versions. That can receive analog input. They can be set to analog input or digital input as either may be used in the program. They will be recognized as analog inputs when the input terminal is connected with an analog function block, and they will be recognized as switching inputs when the input terminal is not connected with an analog function block.
2. The analog inputs require DC 0V ~ +10V voltage signals. These are divided equally in 0.02V increments. In programming, all the block parameters related to the analog inputs are based on the minimum increment of 0.02V.
3. They can be recognized as switching input when the input voltage is more than 10.0V and cannot be recognized as an analog input.
2. Connecting x-Messenger is shown as in the following figures:
*
EXM-3DC, EXM-6DC and EXM-12DC Series inputs
*
EXM-8AC Series inputs
98
* EXM-Analog Inputs (DC 0…10V)
*EXM current Inputs (0…20mA)
The above figure shows how to make a four-wire current measurement.
Connect two-wire sensor to EXM which has the current(0/4…20mA) input.
Two-wire sensor wiring is as follows:
1. Connect the output of the sensor to the “AI3” terminal (0…20mA current measurement) of x-Messenger module.
2. Connect the attached connector of the sensor to the +24V (L+) of power supply.
3. Connect the current output terminal M to the corresponding M terminals of Power supply.
Note: this figure can be applied to EXM-12DC-DA CPUs and the extension which has current inputs.
4.3.3 Connecting EXM Outputs
1.Requirement for the relay output
Various loads such as lamp, fluorescent tube, motor, contact, etc., can be connected to the outputs of x-Messenger. The maximum ON output current that can be supplied by x-Messenger is 10A for the resistance load and 2A for the inductive load. The connection is in accordance with the following figure:
99
2. Requirement for the electronic transistor output:
The load connected to x-Messenger must have the following characteristics:
* The maximum switch current cannot exceed 0.3A.
* When the switch is ON (Q=1), the maximum current is 0.3A.
Notes (PNP):
* The load connecting voltage must be ≤60VDC and it must be DC.
* The “+” terminal of the output wiring must be connected with the DC positive voltage, and it must be connected with the “L+” terminal of the x-Messenger power ,a load must be connected with the “-” terminal of the DC negative voltage.
100
Chapter 5 Configuring & Software-standard mode
5.1 System requirements
The “eSMSConfig.exe” configuration software runs on the current Microsoft operating systems. The following minimum system requirements must be met in order that the software functions properly:
Operating system:
Windows2000
Windows XP
Windows Vista
Windows7
CPU computer capacity:
Pentium II / 166MHz
Recommended: Pentium III / 800MHz
RAM:
256MB (Windows XP)
Hard disc storage capacity available
40MB
Programming interface:
RS232
USB
Ethernet
*Screen resolution
Minimal: 1024 x 768 pixels
*PLEASE NOTE:
If the screen resolution is too low, the window of the programming software will not be displayed in the normal size. That means some tabs or buttons would be outside the screen window and therefore invisible.
To avoid this, change the screen resolution of your computer system. Select “Start” – “System controls” –
“Display” and then the register “Settings”. Please set the screen resolution to 1024 x 768 pixels in minimum.
101
5.2 General
The x-Messenger is configured and prepared for use with the “eSmsConfig.exe” configuration software. The x-Messenger configuration (telephone book creation, message definitions, default settings, etc.) can be done on a PC and saved in a respective file without connection to the device. In order to do this, the software is started, a new or existing file opened and edited. The saved file needs to be downloaded to the x-Messenger with the programming cable. In offline mode, the diagnostic functions are not active and can only be accessed once the x-Messenger is connected to the PC via RS232, USB or Ethernet interface.
Two modes available in eSmsConfig.exe: A. Standard mode B. Customized mode
Who will use the standard mode?
Users who are not familiar with PLC programming, and furthermore merely simple control or no multiple logic would be required for their applications.
Who will use the customized mode?
Users who are familiar with the logic boxes of Boolean algebra, and moreover complex control, logic, timer, counter, analog math etc would be needed for their systems.
Chapter 6 shall introduces the standard mode and for customized mode in detail, please refer to the chapter7.
Fig 6.1 standard mode
102
5.3 Create connection
1.Cut off the power supply of the x-Messenger SMS Relay
2.Insert the SIM card
3.Connect the x-Messenger module and PC via the following optional methods:
Option A . EXM-RS232 /EXM-USB
Option B . EXM-USB-B
Option C . Ethernet (Only available for the model which has Ethernet interface )
4. Connect power supply to the x-Messenger SMS Relay
5. As soon as the Status-LED of the x-Messenger SMS Relay flushes in a cycle off 1 second, the software can be started.
6. Choose a saved file or create a new one.
7.For transmission, choose the required COM port of your PC or required IP address and port
Number by click” ”..
Everything is now set up to download the prepared configuration file to the device.
5.4 Edit telephone book
Add – register of a new phone number
Edit – editing of an already existing entry
Delete – deleting of an existing entry
Please enter the phone number in international format (i.e. with country code and prefix), e.g.
+41793333333. (+41 Switzerland; +49 Germany, +31 Netherland, etc)
5.5 Standard mode settings
The default settings for SMS transmission contain important general data which help to identify the device.
The SIM card can be protected with a PIN code just like for normal cell phone use. The PIN request is activated and the PIN code is input in the required field. This concerns PIN1. Further information can be obtained from the SIM card manual. Likewise the process of unblocking the SIM card after three incorrect inputs of PIN1 is described in the SIM manual. In order to do this, the SIM card must be removed from the SMS Relay and
103
inserted into a mobile phone. Now the card can be unblocked according to the details of the network providers.
5.5.1 Device types
Depending on the device type, the correct type has to be selected. The selection has an influence on the configuration of the inputs and outputs. It is however possible to correct the selected type at any time.
5.5.2 Automatic provider search
The automatic provider selection depends on the SIM card inserted into the SMS Relay. The provider details and access of the SIM card are adapted. Basically, the provider is preassigned when the SIM card is purchased. With the “Automatic” setting, the network provider is automatically searched and logged. That is useful if the card is used in the home network. Other GSM networks can be accessed abroad with the same
SIM card according to the roaming contracts.
5.5.3 Manual provider search
For manual provider searches, the available GSM networks are scanned several times. The results of this search are displayed with a list of networks. A mouse click on “Search“, and then the available networks would be shown. The desired network can now be chosen. The SMS service centre number can be taken from the SIM card documentation. Normally this number is already saved on the SIM card. The number depends on the GSM provider.
104
5.6 Status messages
The receiver of the status messages can be chosen from the telephone book. In order to do this click with the mouse pointer onto the expand arrow and select the required entry.
The SMS relay can send the following status messages:
Remote enquiry of all inputs and outputs
The device offers the possibility to interrogate all input and output states by SMS. A code word is therefore sent by SMS to the device. The code word can be individually created. The default code word is: ?#all
The answer is sent to the same phone number from which the correct code word was received (phone number identification). The states of the inputs and outputs are displayed as follows in the SMS message:
Message at the start
A message for each start up (switching on / return of power) of the SMS relay is sent (According to the phone number assigned to the event). The message contents can be edited.
Periodical message
The periodic message provides information of the device’s current status and is sent periodically. The message can be sent daily (time), weekly (time, weekday) or monthly (time, date). The message text can be edited. It is for checking functionality or operation confirmation.
Note: All messages have two optional message formats: A. TEXT B. PDU(UCS2) (Protocol Data
Units)
A.TEXT is supposed to support ASCⅡ.( Up to 100 chars can be edited)
B.PDU is supposed to support multi languages.(Up to 70 chars can be edited)
5.7 Input configuration
5.7.1 General
Depending of the device type, all this inputs can be used as digital inputs or as digital / analogue
inputs .
105
5.7.2 Digital inputs
Each one of these inputs can activate an SMS message to a predefined telephone number either in case of
HIGH or LOW input signal (up to 5 various numbers).
Basically two events can trigger an SMS message: the change from LOW-to-HIGH and the inverse, the change from HIGH-to-LOW. One or both events can be configured to activate a message. A separate text message can be entered for each event. For details refer to 6.8.2.2 and 6.8.2.3
With confirmation function activated:
If the SMS Relay does not receive an acknowledgement SMS within a certain preset time from the receiver, the event message will be sent to the next receiver. This means that the device runs through the 5 allocated receiver numbers and restarts afterwards with the first number again (The number of running loops can be pre-defined). As soon as the device receives a confirmation from the receivers the process is stopped. If this is not the case, the message will be sent to the next receiver (after expiry of the preset time).
If the confirmation is inactive, all receivers who are allocated to that event will receive a message without repetition.
If the confirmation code word is not activated, the phone number identification is carried out as a security check and it is sufficient to send an empty SMS message to the x-Messenger SMS Relay.
5.7.2.1 Parallel message handling
It may occur that the status of several inputs change at the same time or within the actual running message cycle. Every input activates its individually message.
Every change of the input status, which triggers an event message, is processed in order of the appearance.
That means that all the messages for every input will be handled individual. Several events at the same time can trigger different messages at the same time. Example: The events “pump breakdown” and “over temperature” (two different inputs) appear at the same time both events are processed individually and both messages will be sent one after the other.
106
5.7.2.2 Time delayed message for input ON
If there is an input signal, the respective message transmission can be time delayed, i.e. the SMS relay only sends the pre-defined message after the preset time has elapsed and if the signal has remained ON constantly during that time. In other words, the input signal is ignored during the set delay time. Time delays of 0.1 seconds to 99.9 hours are possible. This time function default must be activated and is to prevent unstable triggers producing numerous SMS messages.
REMARK
event.
It is recommended to use the delay function to avoid several messages being sent for the same
107
5.7.2.3 Time delayed message for output OFF
If an input changes from HIGH to LOW, i.e. there is no longer an input signal, a delayed message can also be activated here. The SMS relay sends the predefined message after the preset time has elapsed and if the signal is no longer present respectively the input signal was constantly OFF during the selected time delay.
Time delays of 0.1 seconds to 99.9 hours are possible. This time function must be activated and is to prevent that unstable short signals as for example of a floating level switch will activate numerous messages.
REMARK same event.
It is recommended to use the delay function to avoid that several messages being sent for the
5.7.3 Analogue inputs
The 4 inputs(AI1—AI4) can be individually configured as digital or analogue inputs. For that purpose each input has to be predefined as analogue or digital input. The analogue inputs(AI1-AI4) are designed for a standard 0 … 10V DC ,AI5 and AI6 are designed for a standard 0 … 20 mA analogue signal.
5.7.3.1 Scaling and units
In a first step, the measuring unit and the scale have to be defined. For both end-values 0V (0 mA) and 10V
108
(20 mA), a minimal and a maximum value of the selected unit is assigned. With this two values, a linear function is interpolated (straight line between 2 points) and displayed in the configuration window. The linear function is adapted automatically in accordance to the set values. The values displayed on the PC screen or transmitted by SMS can be display in different resolutions:
d integer value, i.e. 5200
d.d one digit after decimal point, i.e. 520.0
d.dd two digits after decimal point, i.e. 52.00
d.ddd tree digits after decimal point, i.e. 5.200
9 characters are available for the description of the units. This unit will be sent with every value message following the actual value:
Example of a message: The temperature is 15.5 C
The top and the bottom thresholds have to be defined to allow sending of messages.
The value between the max and the min value is the range R. This range has an important function in the designation of the thresholds.
The maximum Upper Level uLevmax ≤ MaxValue
109
Inserted values higher than MaxValue are corrected automatically by the software.
The minimum Lower Level lLevmin ≥ MinValue
Inserted values lower than MaxValue are corrected automatically by the software
Example:
Max. value 600m3/h 10V of the analog signal
Min. value 150m3/h 0V of the analog signal
The above example allows monitoring the scenario as seen below:
The actual measured value is higher than the defined upper limit.
The system is not in its normal status. The upper limit is exceeded. A message is sent (if thisis activated by
). The message text can be freely configured.
The actual measured value is between the Upper and the Lower Level.
The installation is in normal status. A message shall be sent (if default set) .
110
On this example the actual measured value is below the set Lower Level
The system is not in its normal status. The value is below the lower limit. A message is sent (if this is activated by ). The message text can be freely configured.
A certain difference between the actual value and the last sent value is exceeded
The SMS Relay monitors the analogue value. A message is sent if the difference exceeds a certain value (if this is activated by ). The message text can be freely configured. The value also can be freely configured .
Periodical messages
The actual values can be sent by SMS periodically in intervals of days, weeks or months. The periodical message is sent to the first receiver. If this message is not confirmed, it will be forwarded automatically to the next receiver.
All message texts can be freely edited. The measured value and the unit are always transmitted together with the message text. A space is inserted automatically between the message text and the value. No space is inserted between the value and the unit.
Periodic message
Request value
The actual present value can be enquired by SMS. The message text can be freely edited. To enquire the actual value, a SMS message has to be sent to the device first. This message text can be edited freely.
However, the incoming SMS text must comply fully with the programmed enquiry text. A space is inserted automatically between the message text and the value. No space is inserted between the value and the unit.
Request value
111
Confirmation
If the SMS Relay does not receive a confirmation SMS within a certain preset time from the receiver, the event message will be sent to the next receiver. This means that the device runs through the 5 allocated receiver numbers and restarts afterwards with the first number again (The number of running loops can be pre-defined). As soon as the device receives a confirmation from the receivers the process is stopped. If this is not the case the message will be sent to the next receiver (after expiry of the preset time). if the acknowledgement is inactive, all receivers who are allocated to that event will receive a message without repetition. If the confirmation code word is not activated, the phone number identification is carried out as a security check and it is sufficient to send an empty SMS message to the x-Messenger SMS Relay.
5.7.3.3 Message delay
If the message criteria are reached, the respective message transmission can be time delayed, i.e. the SMS relay only sends the pre-defined message after the preset time has elapsed and if the value has remained constantly during that time. In other words, the measured value is ignored during the set delay time. Time delays of 0.1 seconds to 99.9
hours are possible. This time function default must be activated and is to prevent that unstable short signals can activate numberless identical SMS messages.
REMARK
event.
It is recommended to use the delay function to avoid several messages being sent for the same
5.7.3.4 Message block
If message criteria are reached, which requires sending of a message, a timer is triggered. There will be no further message (same messages) sent during that pre-set time. With that setting it can be avoided that the same status message is sent repeatedly during a set time (Block time).
REMARK
It is recommended to use the delay function to avoid several messages being sent for the same
event.
112
5.8 Output configuration
5.8.1 General
The x-Messenger SMS Relay has max.4 relay outputs (NO 10A, 250V). The outputs can be controlled by a message i.e. they can be switched ON and OFF. Each output can be activated individually. The message text can be edited individually. However, the device only accepts the exact expression i.e. the message must correspond exactly with the registered expressions. Upper and lower cases are ignored, spaces between the words and other characters must be typed correctly. Switching commands are only accepted from numbers which are registered in the telephone book. That means, an output can be switched ON or OFF by receiving a SMS message. The SMS Relay confirms this with an acknowledging message to the sender after carrying out the action. An additional message can be defined, to inform the sender if the output is already switched to the required state and consequently no action will be carried out.
Default
A click on this button will reset the ON/OFF instructions to factory setting.
5.8.2 Timer function
An output can be switched ON for a certain time with the time function option. With that function the output can be switched ON with an SMS message for a preset time. The output will switch OFF again automatically without the need of receiving an OFF message again after that time has elapsed. Time delays of 0.1 seconds to 99.9 hours are possible. The output OFF is reconfirmed to the sender after set time has expired. If a switch-OFF message is received before the set time has elapsed, the output will ignore the remaining ON time and switches to OFF status
113
immediately. The default of that timing function is normally inactive and therefore must be activated.
WARNING
This device is not suitable for monitoring sensitive installations or time critical processes. GSM network failure or power interruptions cannot guarantee a secure monitoring.
5.8.3 CALL-IN function
The CALL-IN function allows the user to activate the outputs by phone call for a certain time as described in chapter 6.9.2. The device detects the incoming call and switches the outputs without answering. The outputs are automatically switched-off after the preset time. This allows activating a process without costs.
REMARK
Activate the output timer to activate the field “Activate Call-In”!
5.8.4 I/O status remote request
With a successful established data connection (via GSM-network connection or via a serial cable connection,
Ethernet connection), the user can ask for the status of all inputs and outputs of the x-Messenger SMS Relay including analogue input values.
REMARK
Modification of values and settings over remote access will not be immediately shown in the I/O states display window. This takes some time and depends on the scanning cycle.
114
Digital IO status and analog input value can be displayed.
5.8.5 Digital inputs
Digital input ON
Digital input OFF
5.8.6 Analogue inputs
The measuring bar always displays the input value 0 to 1000 ,which represents the analog input signal 0 to
10V DC(0…20 mA).
Example:the input signal is 5V DC(10mA) , so the value shall display 500.
5.8.7 Outputs
115
The states of the outputs are displayed with ON and OFF.
Chapter 6 Configuring & Software-customized mode
Users who are familiar with the logic boxes of Boolean algebra can use the customized mode. In fact customized mode adapts the function block programming way. eSmsConfig is available as a programming package for the PC. This mode provides many features, for example:
–
–
–
–
–
A graphic interface for offline creation of your circuit program by means of Function
Block Diagram (function chart)
–
–
Simulation of your circuit program on the PC
Generating and printing of an overview chart for the circuit program
Saving a backup of the circuit program on the hard drive or other media
Easy configuration of blocks
Transferring the circuit program from the x-Messenger to the PC and
1.
from the PC to x-Messenger
Setting the TOD
Online test: Display of status changes and process variables of x-Messenger in RUN mode:
Status of a digital I/O, shift register bits and cursor keys
The values of all analog I/Os
The results of all blocks
The current values (including the times) of selected blocks
Change the output(the input pin of the output cannot be connected) status via eSmsConfig with customized mode
Starting and stopping circuit program execution via the PC (RUN, STOP).
The x-Messenger alternative
As you can see, eSmsConfig represents an alternative to conventional engineering methods:
116
1.
You start by developing the circuit program on your desktop.
2.
You simulate the circuit program on your computer and verify its functions, before you actually implement it in your system.
3.
You can add comments to the circuit program and create hardcopies.
4.
You save a copy of your circuit program to the file system on your PC, to make it directly available for any modifications.
5.
It takes only a few key actions to download the circuit program to x-Messenger.
6.
Under Simulate mode in eSmsConfig, you can study how to program via the panel key.
6.1 x-Messenger Functions
EXM series customized mode adopts the programming methods by the use of function blocks. A total of 8 general function blocks, 30 special function blocks, and 6 input & output function blocks are configured. And each block can achieve a specific control function independently, e.g. TOND, TOFD, SBPL, TBPL, SCHD, etc. As several blocks are linked up in a specific way, relatively complicated control functions can be performed.
Programming with function blocks is simpler and better appreciated than the conventional PLC instruction programming.
The following types of operator for x-Messenger function blocks are available for options:
6.2 General Input & Output functions
6.2.1 Inputs
Input blocks represent the input terminals of x-Messenger. Up to 8 digital inputs are available to you.
In your block configuration, you can assign an input block a new input terminal, if this terminal is not already used in the circuit program.
117
6.2.2 Cursor keys
Up to four cursor keys are available to you. Cursor keys are programmed for the circuit program in the same ways as other inputs. Cursor keys can save switches and inputs, and allow operator control of the circuit program.
6.2.3 Outputs
Output blocks represent the output terminals of x-Messenger. You can use up to 4 outputs. In your block configuration, you can assign an output block a new terminal, provided this terminal is not already used in your circuit program.
The output always carries the signal of the previous program cycle. This value does not change within the current program cycle.
6.2.4 Permanent logical levels HI and LO
Set the block input to logical hi (hi = high) to set it permanently to logical '1' or 'H' state.
118
Set the block input to logical lo (lo = low) to set it permanently to logical '0' or 'L' state.
6.2.5 Open Connector
Interconnect the output of an unused block with the "open connector" block. Up to 512 can be used in one program.
6.2.6 Panel Key
It is the symbol of the Function key on the panel (F1—F4). If one of the function keys is pressed down, the status of the corresponding symbol in the program shall turn from 0 to 1. And it shall give off one high trigger.
Notes: 1.Only one function key is allowed to be pressed down at any one time, if you press down two or more at the same time, x-Messenger does not process.
2. If the arrow keys(UP, DOWN, LEFT and RIGHT), Esc and OK had been applied to the program, then they would be invalid for menu operation (e.g. manual programming,parameters modification and view alarming message etc).
119
6.2.7 Shift register bits
x-Messenger provides the shift register bits S1 to S8, which are assigned the read-only attribute in the circuit program. The content of shift register bits can only be modified by means of the Shift register special function
6.2.8 Analog inputs
You can use up to 36 analog inputs. In your block configuration, you can assign a new input terminal to an input block, provided this terminal is not already used in the circuit program.
For help on analog block parameter, refer to Information on analog value processing.
120
6.2.9 F (digital flag)
Flags are used when x-Messenger works in a communication system. F is digital flag which is used to save
/transfer signal 1 or 0(data format is Bit) and AF is analog flag which is used to save /transfer analog values
(data format is Signed short) between the master and slave devices. Both of the flags (digital/analog) are up to 64 can be used when programming. In your block configuration, you can assign a new number to the flag, provided this flag number does not already exist in your circuit program.
The output always carries the signal of the previous program cycle. This value does not change if the communication has failed.
Startup flag: F8
The F8 flag is set in the first cycle of the user program and can thus be used in your circuit program as a
startup flag. It is reset after the first program execution cycle.
In the subsequent cycles, the F8 flag reacts in the same way as the F1 to F64 flags.
Backlight flags: F64
The F64 flag controls the backlight of the x-Messenger onboard display.
You can use the outputs of timers, message texts, or other function blocks to activate the backlight flags. To enable multiple conditions to control the backlight of the devices, you can use multiple function blocks in parallel or in sequence.
Notes: 1.The address of “ F“ can be found in the modbus communication protocol file . the F block figure must have the input pin in the eSmsConfig showing.
2. Keep the input pin of F NULL(do not connect with other blocks) ,if you want to use the write property.
6.2.10 AF (Analog flag)
Flags are used when x-Messenger works in a communication system. F is digital flag which is used to save
/transfer signal 1 or 0(data format is Bit) and AF is analog flag which is used to save /transfer analog values
(data format is Signed short) between the master and slave devices. Both of flags (digital/analog) are up to
121
64 for x-Messenger CPU can be used when programming. In your block configuration, you can assign a new number to the analog flag, provided this flag number does not already exist in your circuit program.
The output always carries the signal of the previous program cycle. This value does not change if the communication were failed.
Notes: 1.The address of “AF“ can be found in the modbus communication protocol file .
2.Keep the input pin of AF NULL(do not connect with other blocks) ,if you want to use the write property.
6.2.11 SMS message input
Short description
Up to 32 SMS message inputs are available for you. SMS message inputs are programmed for the circuit program in the same ways as other digital inputs. SMS message inputs allow operator control of the circuit program by means of short message or “Incoming Call” by users’ handsets. Users send pre-set short message content to change the status of SMS message inputs from “0”/OFF to “1”/ON or “1”/ON to “0”OFF.
And then the program (circuit diagram) shall take the logic state of the SMS message input into the logic to realize a certain control function.
General description of parameter dialog box:
122
1. Phonebook: click this button, you can edit the phonebook
You are allowed to edit Phone book by clicking the button in the toolbar as shown below :
2. Incoming Message configuration
3. Incoming Call configuration
4. Receiver selection
123
There are two option control modes for the SMS message input:
A.Incoming message B.Incoming Call
Incoming Message mode means that you can send a pre-set short message to control the state of “ SMS message input“
Number identification: If the box were ticked, only the short messages from the telephone settings(Up to 5 user’s phone number can be selected from the phone book) can be recognized by the x-Messenger, only when the contents is the same as the pre-set one,then the SMS message input state would be changed correctly.
On instruction: Here you can pre-edit the short message contents to control the “SMS message input“ ON/HIGH“. The default setting is1#1.
OFF instruction: Here you can pre-edit the short message contents to control the “SMS message input
“ OFF/LOW“.The default setting is “1#0“
OFF-Delay:If the “Enable Delay” box were ticked, after the message input status changes from Low to High via a preset short message, then the status of SMS message input block would switch off(reset to
Low) on expiration of the preset delay time(1...99 seconds). If this item was not enabled, the SMS message does not reset automatically.
Incoming Call mode means you can dial the phone number of the x-Messenger to control SMS message input state. While the x-Messenger gets one incoming call but it does not answer, the SMS message state would change from 0 to1. After the call being timed-out or cut off, the SMS message state would change 1 to 0.
Answer Call: If the box were ticked, the x-Messenger shall pick up your call but without any voice. This item can help you ensure the x-Messenger has got your phone correctly and you can control the
SMS message input which keeps high for 10 seconds unless you cut off the call.
Note: If answer call is not selected. You call the x-Messenger would not have call cost. Contrarily, the call cost would exist.
6.2.12 SMS message output
Up to 64 SMS message outputs are available. Each one of these message outputs can send an SMS message or Call out without voice. Only the change from LOW-to-HIGH can trigger an SMS.
Caution : Please remember every SMS message output needs at least one phone number in its list. The display of special characters in the GSM network can cause problems. Please use only text characters and figures. The programming software identifies special characters and an error messages will occur.
Short description
124
The output would not be high until all the pre-defined short messages were successfully sent out.
Connection
Input Trg
Input R
Description
Start sending short message out (Trigger)
Only reset the output signal to 0.
Output Q Q is switched on after all the short message sent out successfully.
General description of parameter dialog box:
1.Message Format :TEXT or PDU (UCS2).
TEXT is supposed to support ASCⅡ.
PDU is supposed to support multi languages.
2. Short message content edit area: Up to 100 characters are available under TEXT mode and up to 70 characters under PDU (UCS2) This area is only for the “Text Message”
3. With confirmation function activated:
If the x-Messenger does not receive an acknowledgement SMS within a certain preset time from the receiver, the event message will be sent to the next receiver. This means that the device runs through the 5 allocated receiver numbers and restarts afterwards with the first number again (The number of running loops can be pre-defined). As soon as the device receives a confirmation from the receivers the process is stopped. If this is not the case, the message will be sent to the next receiver (after expiry of the preset time).
If the confirmation is inactive, all receivers who are allocated to that event will receive a message without
125
repetition.
4. Phonebook: click this button, you can edit the phonebook
You are allowed to edit Phone book by clicking the button in the toolbar as shown below:
5. Receiver selection
6. On message delay
--
Time delayed message for input ON
If there is an input signal, the respective message transmission can be time delayed, i.e. the x-Messenger only sends the pre-defined message after the preset time has elapsed and if the signal has remained ON constantly during that time. In other words, the input signal is ignored during the set delay time. Time delays of 0.1 seconds to 99.9 hours are possible. This time function default must be activated and is to prevent sending of numerous identical SMS messages.
REMARK
It is recommended to use the delay function to avoid that several messages are sent for the same event.
7. Keyword for confirmation
If the confirmation code word is not activated, the phone number identification is carried out as a security check and it is sufficient to send an empty SMS message to the SMS Relay.
Usage instruction for “Parameters Message” sector:
First of all, select “Parameter Message”, and then click “Set Message” button,the below configuration appears :
126
A. Select “I/O”, hereunder “Block” section consists of “Main CPU”, 8 pieces extensions, hence any of
“Main”,“Ext 01”,“Ext 02”,… can be selected,as below configuration shows:
After that, Main CPU’s I/O will appear in “Parameter” section, so you can select “Input” or ”output”, further click “Insert” button, the editing area will display the ”input” or “output” as below configuration shows, finally click "ok" button to finish and confirm your insertion :
Certainly, you are also allowed to add text description in the blank area, as above configuration shows
127
B. Select “Analog I/O”, hereunder “Block” section consists of “8-route analog inputs of Main CPU”, “ 2-route analog inputs for 31 pieces expansion modules respectively,… can be selected,“Analog I/O” insertion method is same as you do with “I/O” above, as below configuration shows:
C. Select “Params”, hereunder “Block” section will automatically list out all function blocks in your program which are able to be inserted into “Editing area”. Then select a certain block, after that, parameters of that selected block will be displayed under “Parameter” section, hence just select specific parameter you would like, further click “ Insert “ button, finally click “ok “ button to finish and confirm your inserting. As below configuration shows:
This block also can be configured as RING alarm.
128
When the En pin had been activated, x-Messenger would dial the phone number in the 5 pre-set receivers.
With confirmation function activated:
If the receiver does not answer the call from x-Messenger within a certain preset time from the receiver, the x-Messenger would dial next receiver. This means that the device runs through the 5 allocated receiver numbers and restarts afterwards with the first number again (The number of running loops can be pre-defined). As soon as the device receives a confirmation from the receivers the process is stopped. If this is not the case, the x-Messenger would dial the next receiver (after expiry of the preset time).
6.2.13 Sms message Input Output
Up to 12 “SMS message input output” blocks can be used in program.
Users can send the message as per the contents in the ON instruction option, the x-Messenger can send
129
the message including the parameters to the phone which sent the message in.
General description of parameter dialog box:
1.Message Format :TEXT or PDU (UCS2).
TEXT is supposed to support ASCⅡ.
PDU is supposed to support multi languages.
2. Short message content edit area: Up to 100 characters are available under TEXT mode and up to 70 characters under PDU (UCS2) This area is only for the “Text Message”
3. With confirmation function activated:
If the x-Messenger does not receive an acknowledgement SMS within a certain preset time from the receiver, the event message will be sent to the next receiver. This means that the device runs through the 5 allocated receiver numbers and restarts afterwards with the first number again (The number of running loops can be pre-defined). As soon as the device receives a confirmation from the receivers the process is stopped. If this is not the case, the message will be sent to the next receiver (after expiry of the preset time).
If the confirmation is inactive, all receivers who are allocated to that event will receive a message without repetition.
4. On message delay --Time delayed message for input ON
130
If there is an input signal, the respective message transmission can be time delayed, i.e. the x-Messenger only sends the pre-defined message after the preset time has elapsed and if the signal has remained ON constantly during that time. In other words, the input signal is ignored during the set delay time. Time delays of 0.1 seconds to 99.9 hours are possible. This time function default must be activated and is to prevent the sending of numerous identical SMS messages.
REMARK
It is recommended to use the delay function to avoid several messages being sent for the same event.
7. Keyword for confirmation
If the confirmation code word is not activated, the phone number identification is carried out as a security check and it is sufficient to send an empty SMS message to the SMS Relay.
Usage instruction for “Parameters Message” sector:
First of all, select “Parameter Message”, and then click “Set Message” button the below configuration is shown:
A. Select “I/O”, hereunder “Block” section consists of “Main CPU”, 8 pieces extensions, hence any of
“Main”,“Ext 01”,“Ext 02”,… can be selected,as below configuration shows:
131
After that, Main CPU’s I/O will appear in “Parameter” section, so you can select “Input” or ”output”, further click “Insert” button, herewith the editing area will display the ”input” or “output” as below configuration shows, finally click "ok" button to finish and confirm your inserting :
Certainly, you are also allowed to add text description in the blank area, as above configuration shows
B.
Select “Analog I/O”, hereunder “Block” section consists of “8-route analog inputs of Main CPU”,
“ 2-route analog inputs for 31 pieces expansion modules respectively,… can be selected,“Analog I/O” inserting method is same as you do with “I/O” above, as below configuration shows:
C.
Select “Params”, hereunder “Block” section will automatically list out all function blocks in your program which are able to be inserted into “Editing area”. Then select a certain block, after that, parameters of that selected block will be dislayed under “Parameter” section, hence just select specific parameter you would like, further click “ Insert “ button, finally click “ok “ button to finish and confirm your inserting. As below configuration shows:
132
6.2.14 GPRS Connect
Short description
This block can be used to enable the GPRS connection or disable the connection.
Connection
Input Trg
Output Q
Description
Enable the GPRS connection according to the settings in the property dialog box via trigger the input.
Q is switched on after the GPRS connection is established.
If the connection disconnected, the output also shall be switched off.
Property box instructions:
133
1.
Timeout time settings: the timeout time of the GPRS connection. If there is no data transmission in the period more than the time of the settings value, the GPRS shall disconnect automatically.
2.
Network parameters settings.
Here there are 2 options for you.
a.
EXM system: If this setting is selected, the IP and the port number of the server shall be the same as the settings in the menu “SMS->GPRS Param” b.
Customized: This option allows you to select another server.
Note: 1.The connection of this block configuration has a higher priority than the menu setting, that means if this block is activated, the GPRS connection of the menu settings shall disconnect automatically.
134
2. The data transmission between x-Messenger and the server is based on standard Modbus TCP protocol.
6.2.15 GPRS Data Upload
Short description
This block can be used to enable the GPRS connection and then transfer some information of the registers to the network server.
Connection
Input Trg
Input R
Output Q
Description
Enable the GPRS connection according to the settings in the property dialog box via trigger the input.
Reset the output and disable the GPRS connection even if the Trg input keeps high.
Q is switched on after the GPRS connection is established and the server software has made right response according to MODBUS TCP .
If the connection disconnected, the output also shall be switched off.
135
1.Timeout
Such time setting is for the GPRS connection. If the server software does not respond within 10 seconds, after x-Messenger transfer the data(pre-set, here is AF1 --AF3 values), then x-Messenger would repeat the data transmission for 3 times, and finally the GPRS connection shall disconnect automatically.
2.Network parameters settings.
There herewith are 2 options for you.
A. EXM system: If this setting is selected, the IP and the port number of the server shall be the same as the settings in the menu “SMS->GPRS Param”
136
B. Customize IP address: This option allows you to select another server.
Note: 1.The connection of this block configuration has a higher priority than the menu setting, that means if this block is activated, the GPRS connection of the menu settings shall disconnect automatically.
C.Domain Name
This block as can be used to establish GPRS connection by domain name.
3. There are 2 format of data frame which transferred from EXM to the server end
A. Standard Modbus (AF1=100,AF2=1000,AF3=10000)
Example program:
137
If you press F1 key, then the EXM will upload the AF1-AF3 value to the server(slave1) as follows:
Server software get the data like this:
00 01 00 00 00 0D 01 10 00 00 00 03 06 00 64 03 E8 27 10
The request and response are prefixed by six bytes as follows byte 0: transaction identifier - copied by server byte 1: transaction identifier - copied by server byte 2: protocol identifier = 0 byte 3: protocol identifier = 0 byte 4: length field (upper byte) = 0 (since all messages are smaller than 256) byte 5: length field (lower byte) = number of bytes following byte 6: unit identifier (previously ‘slave address’) byte 7: MODBUS function code byte 8: Register of slave start address byte 9: Register of slave start address byte 10:number of registers byte 11:number of registers byte 12:data length field (lower byte) = number of bytes following
So, AF1 = 00 64 (DECIMAL 100)
AF2 =03 E8 (DECIMAL 1000)
AF3 = 27 10 (DECIMAL 10000)
The the server end(slave1) do response
00 01 00 00 00 06 01 10 00 00 00 03
So if the "Trg" input keeps high, the the output will be high also after the EXM get the above correct response.
Note: The Modbus code 16 is used to upload the analog value(includes analog inputs, analog outputs, analog flag and REG), Modbus code 15 is used to upload the digital status for digital flag, digital output, and digital input.
B. customize Modbus
For example,configuration in program like this:
B. Standard Modbus
For example,configuration in program like this:
138
Server software gets the data like this:
00 09 00 00 00 4c 01 8b 49 14 78 2d 4d 65 73 73 65 6e 67 65 72 20 73 74 61 74 69 6f 6e 31 01 01 01 02
01 0d 0b 08 00 80 00 88 00 00 00 00 0c 08 00 00 00 00 00 80 00 88 16 01 02 17 08 01 c2 00 00 02 26 00
00 07 01 04 0d 08 00 00 00 00 00 00 01 c2
Description:
00 09 00 00 00 4c : MODBUS TCP data prefixed by six bytes
01 :x-Messenger address(the default is 01)
8b : Upload code(fixed, if GPRS Data upload used)
49 :length field =number of bytes following
14 :length field = number of bytes of Identification string
78 2d 4d 65 73 73 65 6e 67 65 72 20 73 74 61 74 69 6f 6e 31 : x-Messenger station1(Identification String)
01 01 01
01 : type code (01 means the digital inputs)
01 : length field = number of bytes of the digital inputs
01 : status of the digital inputs(I3=1,I4=0,I5=0,I6=0)
02 01 0d
02 : type code (02 means the digital outputs)
139
01 : length field = number of bytes of the digital outputs
0d : status of the digital outputs (Q1=1,Q2=0,Q3=1,Q4=1)
0b 08 00 80 00 88 00 00 00 00
0b : type code (0b means the Analog Input)
08 :length field = number of bytes of the analog inputs
00 80 00 88 00 00 00 00 : analog inputs value (AI1= 00 80 , AI2 = 00 88, AI3= 00 00,AI4= 00 00)
0c 08 00 00 00 00 00 80 00 88
0c : type code (0c means the Analog output)
08 : length field = number of bytes of the analog outputs
00 00 00 00 00 80 00 88 : analog outputs value (AQ1= 00 00 , AQ2 = 00 00, AQ11= 00 80,AQ12= 00 88)
16 01 02
16 : type code (16 means the digital flag)
01 : length field = number of bytes of the digital flag
02 : status of the digital flag (F1=0,F2=1,F3=0,F4=0)
17 08 01 c2 00 00 02 26 00 00
17 : type code (17 means the Analog flag)
08 : length field = number of bytes of the analog flag
01 c2 00 00 02 26 00 00 : analog flag value (AF1= 01 c2 , AF2 = 00 00, AF3= 02 26,AF4= 00 00)
07 01 04
140
07 : type code (07 means the M status)
01 : length field = number of bytes of M(Function block status(1/0))
04: status of the M (M1=0,M2=10,M3=1,M4=0)
0d 08 00 00 00 00 00 00 01 c2
0d : type code (0d means the AM value)
08 : length field = number of bytes of AM
00 00 00 00 00 00 01 c2: AM value (AM1=00 00,AM2=00 00,AM3=00 00,AM4=01 c2)
The server end need do response like this:
00 00 00 00 00 02 01 8b
You can use the above fixed data as the response for the customize MODBUS.
So if the "Trg" input keeps high, the the output will be high also after the EXM get the above correct response.
Note:The command format is based on the standard Modbus TCP. Please refer to the technical file "Modbus
TCP communication protocol" for detail if require.
6.3 Basic functions list – GF
Basic functions represent simple logical elements of Boolean algebra.
You can invert the inputs of individual basic functions , i.e. the circuit program inverts a logical “1” at a relevant input to a logical “0”; if “0” is set at the input, the program sets a logical “1”.
The GF list contains the basic function blocks you can use for your circuit program. The following basic functions are available:
View in the circuit diagram View in x-Messenger Name of the basic function
AND
AND with edge evaluation
NAND
( Not AND)
141
BOOLEAN FUNCTION
6.3.1 AND
(Symbol in x-Messenger)
The output of an AND function is only 1 if all inputs are 1, i.e. when they are closed.
A block input that is not used (x) is assigned: x = 1.
Logic table of the AND block:
Input1
0
0
0
0
0
0
Input2
0
0
0
0
1
1
1
0
0
1
0
Input 3
0
Input 4
0
1
0
1
0
1
Output
0
0
0
0
0
0
142
NAND with edge evaluation
OR
NOR
(Not OR)
XOR
(exclusive OR)
NOT
(negation, inverter)
BOOLEAN FUNCTION
1
1
1
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
0
0
0
0
1
0
0
0
0
7.3.2 AND with edge evaluation
(Symbol in x-Messenger)
The output of an AND with edge evaluation is only 1 if all inputs are 1 and at least one input was 0 during the last cycle.
The output is set to 1 for the duration of one cycle and must be reset to 0 for the duration of the next cycle before it can be set to 1 again.
A block input that is not used (x) is assigned: x = 1.
Timing diagram of an AND with edge evaluation
143
6.3.3 NAND
(Symbol in x-Messenger)
The output of an NAND function is only 0 if all inputs are 1, i.e. when they are closed.
A block input that is not used (x) is assigned: x = 1.
Logic table of the NAND block:
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
Input 1
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
Input 2
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
Input 3
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Input 4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
Output
144
6.3.4 NAND with edge evaluation
The output of a NAND with edge evaluation is only 1 at least one input is 0 and all inputs were 1 during the last cycle.
The output is set to 1 for the duration of one cycle and must be reset to 0 at least for the duration of the next cycle before it can be set to 1 again.
A block input that is not used (x) is assigned: x = 1.
Timing diagram of a NAND with edge evaluation
145
6.3.5 OR
The output of an OR is 1 if at least one input is 1 (closed).
A block input that is not used (x) is assigned: x = 0.
Logic table of the OR function:
(Symbol in x-Messenger)
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
Input 1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
Input 2
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
Input 3
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Input 4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
1
Output
146
6.3.6 NOR
(Symbol in x-Messenger)
The output of a NOR (NOT OR) is only 1 if all inputs are 0 , i.e. when they are open. When one of the inputs is switched on (logical 1 state), the output is switched off.
A block input that is not used (x) is assigned: x = 0.
Logic table of the NOR function:
1
1
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Input 1
0
0
1
1
0
0
1
1
1
1
0
0
0
0
1
1
Input 2
0
0
1
1
1
1
1
1
0
0
1
1
0
0
0
0
Input 3
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Input 4
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
Output
147
6.3.7 XOR
(Symbol in x-Messenger)
The XOR (exclusive OR) output is 1 if the signal status of the inputs is different.
A block input that is not used (x) is assigned: x = 0.
Logic table of the XOR function:
Input 1
1
1
0
0
Input 2
0
1
0
1
Output
1
0
0
1
6.3.8 NOT
(Symbol in x-Messenger)
The output is 1 if the input is 0. The NOT block inverts the input status.
Advantage of the NOT, for example: x-Messenger no longer requires break contacts. You simply use a make contact and convert it into a break contact with the help of the NOT function.
Logic table of the NOT function:
Input 1 Output
0
1
1
0
148
6.4 Basics on special functions
Because of their different input designation, you can see right away that there is a difference between the special functions and basic functions. SFs contain timer functions, retentive functions and various parameter assignment options, which allow you to adapt the circuit program to suit your own requirements.
This section provides you with a brief overview of input designations and with some particular background information on SFs. The SFs in particular are described in Chapter7.5
6.4.1 Designation of the inputs
Logical inputs
Here, you will find the description of the connectors you can use to create a logical link to other blocks or to the inputs of the x-Messenger unit.
S (Set):
A signal at input S sets the output to logical “1”.
R (Reset):
The reset input R takes priority over all other inputs and resets the outputs.
Trg (Trigger):
This input is used to trigger the start of a function.
Cnt (Count):
This input is used for counting pulses.
Fre (Frequency):
Frequency signals to be evaluated are applied to this input.
Dir (Direction):
This input determines the direction of count.
En (Enable):
This input enables a block function. When this input is “0”, other signals to the block will be ignored.
Inv (Invert):
A signal at this input inverts the output signal of the block.
Ral (Reset all):
All internal values are reset.
149
Parameter inputs
At some of the inputs you do not apply any signals. You configure the relevant block values instead. Examples:
Par (Parameter):
This input will not be connected. Here, you set the relevant block parameters (times, on/off thresholds etc.).
No (Cam):
This input will not be connected. Here, you configure the time patterns.
P (Priority):
This is an open input. Here, you define priorities and specify whether a message is to be acknowledged in
RUN.
6.4.2 Time response
Parameter T
In some of the SFs it is possible to configure a time value T. When you preset this time, note that your input values are based on the time base set:
Time base s (seconds) m (minutes) h (hours)
_ _ : seconds minutes hours
_ _
: 1 /100 seconds
: seconds
: minutes
Accuracy of T
Because of slight tolerances in the characteristics of electronic components, the set time T may deviate. The x-Messenger has a maximum tolerance of ± 0.02 %.
150
When 0.02 % of the time T is smaller than 0.02 seconds, the maximum deviation is 0.02 seconds.
Example: The maximum tolerance per hour (3600 seconds) is ±0.02%, which is proportional to ± 0.72
seconds. The maximum tolerance per minute (60 seconds) is ± 0.02 seconds.
Accuracy of the timer (weekly/yearly timer)
The maximum timing in accuracy is ± 5 s/day.
6.4.3 Backup of the real-time clock
Because the internal real-time clock of an x-Messenger is backed up, it continues operation after a power failure. The ambient temperature influences the backup time. At an ambient temperature of 25°C, the typical backup time of x-Messenger is 100 hours.
6.4.4 Retentivity
The switching states and counter values of SFs can be set retentive. This means that current data is retained after a power failure, and that the block resumes operation at the break point. The timer is not reset, but resumes operation until the time-to-go has expired, for example, to enable this response, however, the relevant functions must be set retentive.
R: The data is retained.
/: Current data is not retained (default). See the section in topic "Second circuit program
" on enabling and disabling retentivity.
SFs hours counter, weekly timer, yearly timer and PI controller are always retentive.
6.4.5 Parameter protection
In the parameter protection settings, you can determine whether or not the parameters can be displayed and edited in x-Messenger parameter assignment mode. Two options are available:
+: The parameter attribute permits read/write access in parameter assignment mode(default).
-: The parameter settings are read–/write–protected in parameter assignment mode, and can be edited only in programming mode. See the parameter protection mode example in the "Second circuit program".
6.4.6 Calculating the gain and offset of analog values
A sensor is connected to the analog input and converts a process variable into an electrical signal. This value of signal lies within the typical range of this sensor. x-Messenger always converts the electrical signals at the
151
analog input into digital values from 0 to 1000. A voltage of 0 to 10 V (or current signal 0/4…20mA) at input
AI is transformed internally into range of values from 0 to 1000. An input voltage exceeding 10 V is shown as internal value 1000.
Because you cannot always process the range of values from 0 to 1000 as predetermined by x-Messenger, you can multiply the digital values by a gain factor and then shift the zero of the range of values (offset). This allows you to output an analog value to the x-Messenger display, which is proportional to the actual process variable.
Parameter
Input voltage (in V)
Input current(in mA)
Internal value
Gain
Offset
Minimum
0
0/4
0
–10.00
–10000
Maximum
≥ 10
≥20
1000
+10.00
+10000
Mathematical rule
Actual value Ax =
(internal value at input Ax∙gain) + offset
Gain and offset calculation
The gain and offset is calculated based on the relevant high and low values of the function.
Example 1:
The available thermocouples have the following technical data: –30 to +70℃, 0 to 10 V DC (i.e. 0 to 1000 in x-Messenger).
Actual value = (internal value ∙gain) + offset, thus
–30 = (0 ∙A) + B, i.e. offset B = –30
+70 = (1000 ∙A) –30, i.e. gain A = 0.1
Example 2:
A pressure sensor converts a pressure of 1000 mbar into a voltage of 0 V, and a pressure of 5000 mbar into a voltage of 10 V.
Actual value = (internal value. gain) + offset, thus
= (0·A) + B, i.e. offset B = 1000
=(1000 ∙A) +1000, i.e. gain A = 4
152
Example of analog values
Process variable
Voltage
(V)
–30 0 C 0
0 0 C
+70 0 C
3
10
1000 mbar 0
3700 mbar 6.75
5000 mbar 10
0
5
10
0
5
10
0
5
10
0
5
10
0
5
10
0
5
10
0
10
0.02
0.02
0.02
0.02
Internal value
Gain
0
300
1000
0
675
1000
0
500
1000
0
500
1000
0
500
1000
0
500
1000
0
500
1000
2
2
2
2
0
500
1000
0
1000
0.1
4
4
0.1
0.1
4
0.01
0.01
0.01
1
1
1
10
10
10
0.01
0.01
0.01
1
1
1
1
1
1
10
10
0.01
0.1
1
10
Offset
0
0
0
–30
–30
–30
1000
1000
1000
0
0
0
5
0
0
0
500
1000
0
5000
10000
5
5
5
500
10
15
500
500
500
1000
1500
0
0
0
0
–200
–200
–200
–200
300
800
–10000 –10000
–10000 0
0
0
2
20
5
10
0
Value shown
(Ax)
–30
0
70
1000
3700
5000
0
153
6.5 Special functions list – SF
When you create your circuit program in eSmsConfig, you find the special function blocks in the SF list.
You can invert the inputs of SFs individually, i.e. the circuit program converts a logical “1” at the input into a logical “0”; a logical “0” it converts into a logical “1”. The table also specifies whether the relevant function can be set retentive (Rem). The following SFs are available:
View in x-Messenger
Timer
Name of the special function
On-delay
Off-delay
Rem
REM
REM
On-/Off-delay
Retentive on-delay
Wiping relay(pulse out)
Edge triggered wiping relay
Asynchronous pulse generator
Random generator
Stairway lighting switch
Multiple function switch
Weekly timer
Yearly timer
REM
REM
REM
REM
REM
REM
REM
Counter
Up/down counter
Hours counter
REM
REM
154
Analog
Miscellaneous
Threshold trigger
Analog threshold trigger
Analog differential trigger
Analog comparator
Analog value monitoring
Analog amplifier
Analog multiplexer
Pulse Width Modulator(PWM)
Analog math
Analog ramp
PI controller
Analog math error detection
Latching relay
Pulse relay
Message texts
Softkey
Shift register
155
Data latching relay
Modbus Read
Modbus Write
Memory Write
Memory Read
6.5.1 On-delay
Short description
The output is not switched on until a configured delay time has expired.
Connection
Trg input
Parameter
Output Q
Description
The on delay time is triggered via the Trg (Trigger) input
T represents the on delay time after which the output is switched on (output signal transition 0 to 1).
Retentivity on = the status is retentive in memory.
Q switches on after a specified time T has expired, provided Trg is still set.
Parameter T
The time for parameter T can also be preset based on the actual value of another, already-configured function. You can use the actual values of the following functions:
Analog comparator: Ax - Ay
Analog trigger: Ax
Analog amplifier: Ax
156
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller:AQ
Data latching relay: AQ
Up/Down counter: Cnt
You select the required function via the block number. Time-base can be adjusted.
The value of "T" can be set/modified in parameter mode. For information on the validity and accuracy of the time base, refer to the x-Messenger time-base list as follows:
Valid ranges of the time-base, if T = parameter
Time-base Max.
value
Min. resolution Accuracy s (seconds) 99:99 m (minutes) 99:59 h (hours) 99:59
10 ms
1s
1 min
± 10 ms
± 1 s
± 1 min
Timing diagram
Description of the function
The time Ta (the current time in x-Messenger) is triggered with the 0 to 1 transition at input Trg.
If the status at input Trg stays 1 at least for the duration of the configured time T, the output is set to 1 when this time has expired (the on signal of the output follows the on signal of the input with delay).
The time is reset if the status at input Trg changes to 0 again before the time T has expired.
The output is reset to 0 when input Trg is 0.
157
6.5.2 Off-delay
Short description
The output with off delay is not reset until a defined time has expired.
Connection
Input Trg
Input R
Parameter
Output Q
Description
Start the off delay time with a negative edge (1 to 0 transition) at input Trg (Trigger)
Reset the off delay time and set the output to 0 via the R
(Reset) input.
Reset has priority over Trg
T: The output is switched off on expiration of the delay time T (output signal transition 1 to 0).
Retentivity on = the status is retentive in memory.
Q is switched on for the duration of the time T after a trigger at input Trg.
Parameter
The time set in parameter T can be supplied by the value of another already-programmed function:
Analog comparator: Ax - Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller:AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "T"can be set/modified in parameter mode.Select the required function by the block number.
The time base is configurable. For information on valid time base ranges and parameter preset, refer to chapter 4.4.1 the On-delay topic.
Timing diagram
158
Description of the function
Output Q is set to 1 momentarily with a 0 to 1 transition at input Trg.
At the 1 to 0 transition at input Trg, x-Messenger retriggers the current time T, and the output remains set.
The output Q is reset to 0 when T a reaches the value specified in T (T a
=T) (off delay).
A one-shot at input Trg retriggers the time Ta.
You can reset the time Ta and the output via the input R (Reset) before the time Ta has expired.
If retentivity is not set, output Q and the expired time are reset after a power failure.
6.5.3 On-/Off-delay
Short description
The on/off delay function is used to set an output after a configured on delay time and then reset it again upon expiration of a second configured time.
Connection
Input Trg
Parameter
Output Q
Description
You trigger the on delay with a positive edge (0 to 1 transition) at input Trg (Trigger).
You trigger the off delay with a negative edge (1 to 0 transition).
T
H is the on delay time for the output (output signal transition
0 to 1).
T
L is the off delay time for the output (output signal transition
1 to 0).
Retentivity on = the status is retentive in memory.
Q is switched on upon expiration of a configured time T
H if Trg is still set. It is switched off again upon expiration of the time
T
L and if Trg has not been set again.
Parameter
159
The on-delay time and off-delay time set in parameter TH and TL can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "TH","TL"can be set/modified in parameter mode. For information about how to modify, refer to chapter 7.2.2 please.
For information on the validity and accuracy of the time base, refer to 7.4.2
Timing diagram
Description of the function
The time T
H is triggered with a 0 to 1 transition at input Trg.
If the status at input Trg is 1 at least for the duration of the configured time T
H
, the output is set to logical 1 upon expiration of this time (output is on delayed to the input signal).
The time T
H is reset if the status at input Trg is reset to 0 before this time has expired.
The time T
L is triggered with the 1 to 0 transition at the output.
If the status at input Trg remains 0 at least for the duration of a configured time T
L
, the output is reset to 0 upon expiration of this time (output is off delayed to the input signal).
The time T
L is reset if the status at input Trg is returns to 1 before this time has expired.
160
6.5.4 Retentive on-delay
Short description
A one-shot at the input triggers a configurable time. The output is set upon expiration of this time.
Connection
Input Trg
Input R
Parameter
Output Q
Description
Trigger the on delay time via the Trg (Trigger) input.
Reset the time on delay time and reset the output to 0 via input R (Reset).
Reset takes priority over Trg.
T is the on delay time for the output (output signal transition
0 to 1).
Retentivity on = the status is retentive in memory.
Q is switched on upon expiration of the time T.
Parameter
The time in parameter T can be provided by the value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "T"can be set/modified in parameter mode.
Timing diagram
Description of the function
161
The current time Ta is triggered with a 0 to 1 signal transition at input Trg. Output Q is set to 1 when Ta reaches the time T. A further pulse at input Trg does not affect Ta.
The output and the time Ta are only reset to 0 with a1 signal at input R.
If retentivity is not set, output Q and the expired time are reset after a power failure.
6.5.5 Wiping relay (pulse output)
Short description
An input signal generates an output signal of a configurable length.
Connection
Input Trg
Parameter
Output Q
Description
You trigger the time for the wiping relay with a signal at input Trg (Trigger)
TL represents the time after which the output is reset
(output signal transition 1 to 0).
Retentivity set (on) = the status is retentive in memory.
A pulse at Trg sets Q. The output stays set until the time T has expired and if Trg = 1 for the duration of this time. A 1 to 0 transition at Trg prior to the expiration of T also resets the output to 0.
Parameter
The off time T can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "TL"can be set/modified in parameter mode.
162
Timing diagram
Description of the function
With the input signal Trg = 1, output Q is set to 1. The signal also triggers the time Ta, while the output remains set.
When Ta reaches the value defined at T (Ta=T), the output Q is reset to 0 state (pulse output).
If the signal at input Trg changes from 1 to 0 before this time has expired, the output is immediately reset from 1 to 0.
6.5.6 Edge triggered wiping relay
Short description
An input pulse generates a preset number of output pulses with a defined pulse/pause ratio (retriggerable), after a configured delay time has expired.
Parameter
Connection
Input Trg
Input R
Parameter
Output Q
Description
You trigger the times for the Edge-triggered wiping relay with a signal at input Trg (Trigger).
The output and the current time Ta are reset to 0 with a signal at input R.
TL, TH: The interpulse period T
L and the pulse period T
H are adjustable.
N determines the number of pulse/pause cycles T
L
/ T
H
:
Value range: 1...9.
Retentivity set (on) = the status is retentive in memory.
Output Q is set when the time T
L has expired and is reset when T
H has expired.
163
The pulse width TH and the interpulse width TL can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller:AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "TH","TL"can be set/modified in parameter mode.
Timing diagram
T
L
= 0; N = 1
Description of the function
With the change at input Trg to 1, the time T
L
(time low) is triggered. After the time T
L has expired, output Q is set to 1 for the duration of the time T
H
(time high).
If input Trg is retriggered prior to the expiration of the preset time (T
L
+ T
H
), the time Ta is reset and the pulse/pause period is restarted.
If retentivity is not set, output Q and the time are reset after a power failure.
164
6.5.7 Asynchronous pulse generator
Description of function
The pulse shape at the output can be modified via a configurable pulse/pause ratio.
Connection
Input En
Input Inv
Parameter
Output Q
Description
You enable/disable the asynchronous pulse generator with the signal at input En.
The Inv input can be used to invert the output signal of the active asynchronous pulse generator..
TL,TH: You can customize the pulse (TL)/ pause (TH) ratio.
Retentivity set (on) = the status is retentive in memory.
Q is toggled on and off cyclically with the pulse times T
H and T
L
.
Parameter
The pulse width TH and the inter-pulse width TL can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "TH","TL"can be set/modified in parameter mode. For information about how to modify, refer to chapter 5.2.2 please.
165
Timing diagram
Description of the function
You can set the pulse/pause ratio at the TH (Time High) and TL (Time Low) parameters.
The INV input can be used to invert the output signal. The input block INV only inverts the output signal if the block is enabled via EN.
If retentivity is not set, output Q and the expired time are reset after a power failure.
6.5.8 Random generator
Short description
The output of a random generator is toggled within a configurable time.
Connection
Input En
Parameter
Output Q
Description
The positive edge (0 to 1 transition) at the enable input En
(Enable) triggers the on delay for the random generator.
The negative edge (1 to 0 transition) triggers the off delay for the random generator.
TH: The on delay is determined at random and lies between 0 s and T
H
.
TL: The off delay is determined at random and lies between 0 s and T
L
.
Q is set on expiration of the on delay if En is still set. It is reset when the off delay time has expired and if En has not been set again.
166
Parameter
The on-delay time TH and the off-delay time TL can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "TH","TL"can be set/modified in parameter mode.
Timing diagram
Description of the function
With the 0 to 1 transition at input En, a random time (on delay time) between 0 s and T
H is set and triggered.
If the status at input En is 1 at least for the duration of the on delay, the output is set to 1 when this on delay time has expired.
The time is reset if the status at input En is reset to 0 before the on delay time has expired.
When input En is reset 0, a random time (off delay time) between 0 s and T
L is set and triggered.
If the status at input En is 0 at least for the duration of the off delay time, the output Q is reset to 0 when the off delay time has expired.
The time is reset if the status at input En returns to 1 before the on delay time has expired.
167
6.5.9 Stairway lighting switch
Short description
The edge of an input pulse triggers a configurable time. The output is reset when this time has expired. An off warning can be output prior to the expiration of this time.
Connection
Input Trg
Parameter
Output Q
Description
You trigger the time (off delay) for the stairway switch with a signal at input Trg (Trigger).
T: The output is reset (1 to 0 transition when the time T has expired.
T
!
Determines the triggering time for the pre-warning.
T
!L
determines the length of the pre-warning time.
Retentivity set (on) = the status is retentive in memory.
Q is reset after the time T has expired. A warning signal can be output before this time has expired.
Parameter
The off-delay time T, the pre-warning time T! and the pre-warning period T!L can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "T"can be set/modified in parameter mode.
Timing diagram
168
Changing the time base
You can change the pre-warning time base and the period.
Time base
T
Seconds
Minutes
Pre-warning time
750 ms
15 s
Hours 15 min
* makes sense only for programs with a cycle time of < 25 ms
Pre-warning period
50 ms
1 s
1 min
Description of the function
Output Q is set to 1 with a 0 to 1 signal transition at input Trg. The 1 to 0 transition at input Trg triggers the current time and output Q remains set.
Output Q is reset to 0 when Ta reaches the time T. Before the off delay time (T - T
!
) has expired, you can output a pre-warning that resets Q for the duration of the off pre-warning time T
!L
.
Ta is retriggered (optional) at the next high/low transition at input Trg and if Ta is expiring.
If retentivity is not set, output Q and the expired time are reset after a power failure.
6.5.10 Multiple function switch
Short description
Switch with two different functions:
Pulse switch with off delay
Switch (continuous light)
Connection
Input Trg
Description
With a signal at input Trg (Trigger) you set output Q
169
Input R
Parameter
Output Q
(continuous light), or reset Q with off delay. Output Q can be reset with a signal at the Trg input.
You set the current time Ta, and reset the output to 0, with a signal at input R.
T: The output is reset (1 to 0 transition) when the time T has expired.
T
L determines the period during which the input must be set in order to enable the permanent light function.
T
!
Determines the on delay for the pre-warning time.
T
!L
determines the length of the pre-warning time.
Retentivity set (on) = the status is retentive in memory.
Output Q is set with a signal at input Trg, and it is reset again after a configured time has expired and depending on the pulse width at input Trg, or it is reset with another signal at input Trg.
Parameter
The off-delay time T, the permanent light time TL, the on-delay pre-warning time T!, and the pre-warning time period T!L can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "T","TL"can be set/modified in parameter mode.
Timing diagram
Description of the function
170
Output Q is set to 1 with a 0 to 1 signal transition at Trg.
If output Q = 0, and input Trg is set hi at least for the duration of TL, the permanent lighting function is enabled and output Q is set accordingly.
The off delay time T is triggered when the status at input Trg changes to 0 before the time T
L has expired.
Output Q is reset when the Ta = T.
Before the off delay time (T - T
!
) has expired, you can output an off pre-warning that resets Q for the duration of the off pre-warning time T
!L
. A further signal at input Trg always resets T and output Q.
Caution
The time base for the T, T
!
and T
!L
must be identical.
If retentivity is not set, output Q and the expired time are reset after a power failure.
6.5.11 Weekly timer
Short description
The output is controlled by means of a configurable on/off date. The function supports any combination of weekdays.
Connection
Parameter
Output Q
Description
At the No1, No2, No3 (cam) parameters you set the on and off triggers for each cam of the weekly timer. The parameter units are the days and the time-of-day.
Q is set when the configured cam is actuated.
Parameter
You can configure a time hysteresis for each individual cam in parameter mode. For information about how
171
to modify, refer to chapter 4.2.2 please.
Timing diagram (three practical examples)
No1: Daily: 06:30 h to 08:00 h
No2: Tuesday: 03:10 h to 04:15 h
No3: Saturday and Sunday: 16:30 h to 23:10 h
Description of the function
Each weekly timer is equipped with three cams. You can configure a time hysteresis for each individual cam.
At the cams you set the on and off hysteresis. The weekly timer sets the output at a certain time, provided it is not already set.
The output is reset at a certain time, provided it is not already reset. A conflict is generated in the weekly timer when the set on time and the set off time at another cam are identical. In this case, cam 3 takes priority over cam 2, while cam 2 takes priority over cam 1.
The switching status of the weekly timer is determined by the status at the No1, No2 and No3 cams.
Days of the week
The prefix "D=" (Day) has the following meaning:
● M: Monday
● T: Tuesday
● W: Wednesday
● T: Thursday
● F: Friday
● S: Saturday
● S: Sunday
Uppercase letters indicate a specific day of the week. A "-" indicates no selection for the day of the week.
On-/Off-times
Any time between 00:00 h and 23:59 h is possible. You can also configure the on time to be a pulse signal. The timer block will be activated at the specified time for one cycle and then the output is reset.
- -:- - means: No on-/off-times set.
Setting the weekly timer
172
To set the on-/off-times:
1. Move the cursor to one of the Cam parameters of the timer (e.g. No1).
2. Press OK. x-Messenger opens the Cam parameter assignment screen form. The cursor is positioned on the day of the week.
3. Press and to select one or several days of the week.
4. Press to move the cursor to the first position of the on-time.
5. Set the on-time.
Modify the value at the respective position, using the keys the various positions, using the keys value - -:- and and . Move to the cursor to
. At the first position, you can only select the
(- -:- - means: No on-/off-times set).
6. Press to move the cursor to the first position of the off-time.
7. Set the off-time (in same way as in step 5).
8. Confirm your entries with OK.
The cursor is now positioned on the No2 parameter (Cam2) and you can configure a further cam.
Special characteristics to note when configuring
The block properties window offers a tab for each one of the three cams. Here you can set the weekly on times for the cams. Each tab offers you in addition an option of defining the on and off times for each cam in hour and minute units. Hence, the shortest switching cycle is one minute.
You can disable the on and off times individually, i.e. you can achieve switching cycles extending across more than one day, for example, by setting the on time for cam 1 to Monday 7:00 h and the off time of cam 2 to
Wednesday 13:07 h, while disabling the on time for cam 2.
173
Backup of the real-time clock
The internal real-time clock of x-Messenger is buffered against power failure. The buffering time is influenced by the ambient temperature, and is typically 100 hours at an ambient temperature of 25°C.
6.5.12 Yearly timer
Caution
Your x-Messenger must be equipped with an internal real-time clock if you are going to use this SFB.
Short description
The output is controlled by means of a configurable on/off date
Connection
Parameter
Output Q
Description
At the No (cam) parameter you set the on and off trigger for the cam of the yearly timer.
Q is set on when the configured cam is switched on.
Parameter
The on and off trigger for the cam of the yearly timer can be set/modified in parameter mode and you can configure what you need. For information about how to modify, refer to chapter 5.2.2 please.
Timing diagrams
Example 1: Yearly mode on, Monthly mode off, Pulse Off, On Time = 2000-06-01, Off Time =
2099-08-31: Every year on June 1 the timer output switches on and remains on until August
31.
174
Example 2: Yearly mode on, Monthly mode off, Pulse on, On Time = 2000-03-15, Off Time =
2099-**-**: Every year on March 15, the timer switches on for one cycle.
Example 3: Yearly mode on, Monthly mode off, Pulse off, On Time = 2008-06-01, Off Time =
2010-08-31: On June 1 of 2008, 2009, and 2010 the timer output switches on and remains on until August 31.
175
Example 4: Yearly mode on, Monthly mode off, Pulse on, On Time = 2008-03-15, Off Time =
2010-**-**: On March 15 of 2008, 2009, and 2010, the timer output switches on for one cycle.
Example 5: Yearly mode off, Monthly mode off, Pulse off, On Time = 2008-06-01, Off Time =
2008-08-31: On June 1, 2008 the timer output switches on and remains on until August 31,
2010.
Example 6: Yearly mode off, Monthly mode off, Pulse selected, On Time = 2008-03-15, Off Time =
****-**-**: On March 15, 2008 the timer output switches on for one cycle. Because the timer does not have a monthly action or yearly action, the timer output pulses only one time at the specified On Time.
176
Example 7: Yearly mode on, Monthly mode off, Pulse off, On Time = 2008-12-15, Off Time =
2010-01-07: On December 15 of 2008 and 2009, the timer output switches on and remains on until January 7 of the following year. When the timer output turns off on January 7, 2010 it does NOT turn on again the following December 15.
Example 8: Yearly mode on, Monthly mode on, On Time = 2008-**-01, Off Time = 2010-**-
05: Starting in 2008, on the first day of each month the timer output switches on and switches off on the fifth day of the month. The timer continues in this pattern through the last month of 2010.
Description of the function
The yearly timer sets and resets the output at specific on and off times.
The off-date identifies the day on which the output is reset again. The first value defines the month, the second the day.
When you select the every month check box, the yearly clock switches on or off at a certain day of every month.
Backup of the real-time clock
The internal real-time clock of x-Messenger is buffered against power failure. The buffering time is influenced
177
by the ambient temperature, and is typically 100 hours at an ambient temperature of 25°C.
Special characteristics to note when configuring
A click on the dialog box enables direct keyboard input of the month and day values. The values entered may not exceed the logical maximum of the relevant input boxes; otherwise eSmsConfig returns an error message.
The calendar icon offers you an easy way of setting the date. It opens a window where you can set the days and months by clicking the relevant buttons.
Sample configuration
The output of an x-Messenger is to be set annually on March 1, reset on April 4, set again on July 7, and reset again on November 19. You need to configure two yearly timers with corresponding on-times. Then logically link the outputs by means of an OR block.
178
Result
Place two yearly timer switch SFBs on your programming interface and configure the blocks as specified.
Create a logical link of the blocks via a standard OR block. The OR output is 1 if at least one of the yearly timer switches is set.
179
6.5.13 Up/Down counter
Short description
An input pulse increments or decrements an internal value, depending on the parameter setting. The output is set or reset when a configured threshold is reached. The direction of count can be changed with a signal at input Dir
Connection
Input R
Input Cnt
Input Dir
Parameter
Description
You reset the output and the internal counter value to zero with a signal at input
R (Reset).
This function counts the 0 to 1 transitions at input Cnt. It does not count 1 to 0 transitions.
Input Dir (Direction) determines the direction of count:
Dir = 0: Up
Dir = 1: Down
On: On threshold
Value range: 0...99999999
Off: Off threshold
180
Value range: 0...99999999
StartVal: Initial value from which to begin counting either down or up.
Retentivity set (on) = the status is retentive in memory.
Output Q Q is set and reset according to the actual value at Cnt and the set thresholds.
Parameter
The on threshold On and the off threshold Off can be provided by the value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "On","Off"and "Cnt"can be set/modified in parameter mode. For information about how to modify ,refer to chapter 5.2.2 please.
Timing diagram
Description of the function
The function increments (Dir = 0) or decrements (Dir = 1) the internal counter by one count with every positive edge at input Cnt.
You can reset the internal counter value to '000000', with a signal at the reset input R. As long as R=1, the output is 0 and the pulses at input Cnt are not counted.
Output Q is set and reset according to the actual value at Cnt and the set thresholds. See the following rules for calculation.
Calculation rule
If the on threshold >= off threshold, then:
181
Q = 1, if Cnt >= On
Q = 0, if Cnt < Off.
If the on threshold < off threshold, then:
Q = 1, if On <= Cnt < Off.
Caution
The function polls the limit value of the counter once in each cycle.
Thus, if the pulses at the fast inputs (ELC-12) or IB/IC(ELC-18) are faster than the scan cycle time, the SFB might not switch until the so specified limit has been exceeded.
Example: Up to 100 pulses per cycle can be counted; 900 pulses have been counted so far. On = 950; Off =
10000. The output is set in the next cycle, after the value has reached 1000.
The output would not be set at all if the value Off = 980
6.5.14 Hours counter
Short description
A configured time is triggered with a signal at the monitoring input. The output is set when this time has expired.
Connection
Input R
Input En
Input Ral
Parameter
Description
A positive edge (0 to 1 transition) at input R resets output Q and sets a configured value MI at the counter for the duration of the time-to-go (MN).
En is the monitoring input. X-Messenger scans the on-time of this input.
A positive edge at input Ral (Reset all) resets both the hours counter (OT) and the output, and sets the configured value
MI at the counter to for the duration of the time-to-go (MN).
That is,
Output Q = 0,
The measured operating hours OT = 0, and
The time-to-go of the maintenance interval
MN = MI.
MI: Maintenance interval to be specified in hour units
Range of values: 0000...9999 h
182
Output Q
OT: Expired total operation time. An offset can be specified.
Q
Range of values: 00000...99999 h
0:
When "R" is selected:
Q = 1, if MN = 0;
Q = 0, if R = 1 or Ral = 1
When "R+En" is selected:
Q = 1, if MN = 0;
Q = 0, if R = 1 or Ral = 1 or En = 0.
The output is set when the time-to-go MN = 0. The output is reset:
When "Q 0:R+En", if
R = 1 or Ral = 1 or En = 0
When "Q 0:R", if R = 1 or Ral = 1.
Timing diagram
MI = Configured time interval
MN = Time-to-go
OT = Total time expired since the last 1 signal at the Ral input
These values are principally held retentive!
Parameter
The maintenance interval MI can be provided by the actual value of another already-programmed function:
183
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
The value of "MI" can be set and modified in parameter mode. For information about how to modify, refer to chapter 4.2.2 please.
Description of the function
The hours counter monitors input En. As long as the status at this input is 1, x-Messenger calculates the time expired and the time-to-go MN. x-Messenger displays these times when set to configuration mode. The output is set to 1 when the time-to-go is equal to zero.
You reset output Q and the time-to-go counter to the specified value MI with a signal at input R. The operation hour counter OT remains unaffected.
You reset output Q and the time-to-go counter to the specified value MI with a signal at input Ral. The operation hour counter OT is reset to 0.
Depending on your configuration of the Q parameter, the output is either reset with a reset signal at input R or Ral, or when the reset signal is 1 or the En signal is 0.
Limit value of OT
The values of the operating hours in OT are retained when you reset the hours counter with a signal at input
R. The hours counter OT continues the count as long as En = 1, irrespective of the status at the reset input
R. The counter limit of OT is 99999 h. The hours counter stops when it reaches this value.
In programming mode, you can set the initial value of OT. The counter starts operation at any value other than zero. MN is automatically calculated at the START, based on the MI and OT values.
Example: MI = 100, OT = 130, the result is MN = 70
Parameter preset
In eSmsConfig, you can define MI and an OT start value.
You determine that Q does not depend on En by selecting the corresponding check box.
Retentivity with the hours counter
The hours counter in the x-Messenger is generally retentive.
However, if the values of the hours counter are lost after a power failure, then select the respective block in
184
your circuit program. Right mouse click on the hours counter and select Block Properties > Parameters. The option Retentivity must be activated and not changeable (grayed out).
If the Retentivity option is not available, then delete the block and insert a new special function hours
counter at the same position.
6.5.15 Threshold trigger
Short description
The output is switched on and off, depending on two configurable frequencies.
Connection
Input Fre
Parameter
Output Q
Description
The function count 0 to 1 transitions at input Fre. ! to 0 transitions are not counted.
Use
Inputs I7,I8(EXM-12) 60kHz
Any other input or circuit element for low frequencies (typical 4 Hz).
On: On threshold
Range of values: 0000...9999
Off: Off threshold
Range of values: 0000...9999
G_T: Time interval or gate time during which the input pulses are measured.
Range of values: 00:05 s...99:99 s
Q is set or reset according to the threshold values.
Parameter
The gate time G_T can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
185
PI controller: AQ
Up/Down counter: Cnt
Data latching relay: AQ
Analog Math AQ
The value of "On","Off"can be set/modified in parameter mode. For information about how to modify, refer to chapter 5.2.2 please.
Timing diagram fa = Input frequency
Description of the function
The trigger measures the signals at input Fre. The pulses are captured during a configurable period G_T.
Q is set or reset according to the set thresholds. See the following calculation rule.
Calculation rule
If the threshold (On) > threshold (Off), then:
Q = 1, if fa >= On
Q = 0, if fa < Off.
If the threshold (On) < threshold (Off), then Q = 1, if
On <= fa < Off.
6.5.16 Latching relay
Short description
A signal at input S sets output Q. A signal at input R resets output Q.
186
Connection
Input S
Input R
Parameter
Output Q
Description
Set output Q with a signal at input S (Set).
Reset output Q with a signal at input R (Reset). Output Q is reset if S and R are both set (reset has priority over set).
Retentivity set (on) = the status is retentive in memory.
Q is set with a signal at input S and remains set until it is reset with signal at input R.
No parameter of Latching relay can be set/modified in parameter mode .
Timing diagram
Description of the function
The latching relay represents a simple binary memory logic. The output value depends on the input states and the previous status at the output.
Logic table of the latching relay:
0
0
1
1
S
0
1
0
1
R x
0
1
0
Q Remark
Status unchanged
Reset
Set
Reset
When retentivity is enabled, the output signal corresponds with the signal status prior to the power failure.
187
6.5.17 Pulse relay
Short description
The output is set and reset with a short one-shot at the input.
Connection
Input Trg
Input S
Input R
Description
You switch output Q on or off with a signal at input Trg
(Trigger) input.
A one-shot at input S (Set) sets the output to logical 1.
A one-shot at input R (Reset) resets the output to logical 0
Parameter Selection:
RS (input R priority), or
SR (input S priority)
Retentivity set (on) = the status is retentive in memory.
Output Q Q is switched on with a signal at Trg and is reset again at the next Trg pulse, if both S and R = 0.
No of Latching relay can be set/modified in parameter mode .
parameter
Timing diagram
Description of the function
The status of output Q changes with each 0 to 1 transition at input Trg and if both S and R = 0, i.e. the output is switched on or off.
Input Trg does not influence the SFB when S = 1 or R = 1.
A one-shot at input S sets the pulse relay, i.e. the output is set to logical 1.
A one-shot at input R resets the pulse relay to its initial state, i.e. the output is set to logical 0.
188
Either the input R takes priority over input S (i.e. the signal at input S has no effect as long as R = 1), or the input S takes priority over input R (i.e. the signal at input R has no effect as long as S = 1), depending on your configuration.
6.5.18 Message text
Short description
Display parameterized message texts and parameters of other blocks in RUN mode.
Connection
Input En
Input P
Parameter
Output Q
Description
A 0 to 1 transition at En (Enable) triggers the output of the message text.
P is the priority of the message text.
1 is the lowest, 64 is the highest priority.
Quit: Acknowledgement of the message text
Text: Input of the message text
Par: Parameter or actual value of another, already configured function (see "Visible parameters or actual values")
Time: Shows the continuously updated time-of-day
Date: Shows the continuously updated date
EnTime: Shows the time of the 0 to 1 transition
EnDate: Shows the 0 to 1 transition of the date
Q remains set as long as the message text is queued.
Description of the function
With a 0 to 1 transition of the signal at input En, the display outputs your configured message text (actual value, text, TOD, date) in RUN mode.
Acknowledgement disabled (Ack = Off):
The message text is hidden with a 0 to 1 signal transition at input En.
Acknowledgement enabled (Ack = On):
After input En is reset to 0, the message text is displayed until acknowledged by pressing the OK button. The message text cannot be acknowledged as long as input En is high.
If several message text functions were triggered with En=1, the message with the highest priority (1 = lowest, 64=highest) is displayed. This also implies that a new message text is only displayed if its priority is
189
higher than that of previously enabled message texts.
After a message text is disabled or acknowledged, the function automatically shows the previously active message text that takes the highest priority.
You can press the and keys to step through multiple active message texts.
Example
This is how two message texts could be shown:
Display field of x-Messenger in RUN mode
Restrictions
Up to 64 message text functions are available for EXM-12 CPUs.
Particular characteristics to be noted when configuring
190
1 "General" area
Here you will find the following settings:·
Priority of the message text
Check box for message text acknowledgement
2 "Blocks" area
Shows a list of all the circuit program blocks and their parameters.
3 "General parameters" area
Shows general parameters such as the current date.
4 "Block parameters" area
Shows the parameters of a block selected from the "Blocks" area which you can output in the message text.
5 "Insert" button
Button for inserting a parameter selected from the “Block parameters” area.
"Block parameters" or "General parameters" area into the message text.
6 "Messages" area
You arrange the message text in this area. Information entered in this area corresponds with that on the x-Messenger display.
7 "Delete" button
Button for deleting entries from the "Messages" area
"Special characters" button
Button for inserting special characters in the "Messages" area
To arrange the message text
191
From the "Blocks" area, select the block whose parameters you want to output.
Drag and drop the parameters required from the "Block parameters" to the "Messages" area. You may also use the "Insert" button to do so.
In the "Mess ages" area, you can add parameter data as required.
Particular characteristics to be noted when configuring
The message text can be configured in the block properties dialog. You can enter up to 4 lines for each message text (the text display of the x-Messenger has 4 x 16 characters) and set the priority. You can move to the next line using the cursor keys or the mouse. Hit the [ENTER] key to confirm all your entries in the block properties dialog and to close the dialog.
You may also enter the actual values of other blocks in the text lines. To do so, select the relevant block from the Block dialog. A Parameter dialog opens to display a list of all parameters available for the selected block.
The block parameter you select in this dialog is written to the selected text line. The actual parameter value is now included when you call the message text.
Set the "Acknowledge message" attribute to specify whether a message is be acknowledged before it is closed.
A. I/O status of CPU and extensions
B .Blocks
192
C. Analog input value of ELC-12 CPU and extensions
D. Analog output value of CPU and extensions
193
E. F (digital flag) status
F. AF(analog flag) value
194
G. M status
H. AM value
195
6.5.18.1 How to change parameters of blocks in displayed message ?
Parameters of blocks can be changed in displayed message if inserted into the “message text
“ block by press “OK” key for 3 seconds.
Step as follows:
A. Insert the parameters of block into message text.(Here is On-delay).
B. Change the page to display the message text contents by arrow keys.
196
C. Press “ok” for 3 seconds and enter into edit mode.
D. Modify value by pressing arrow keys and confirm with OK key.
197
6.5.19 Softkey
Short description
This SFB provides the action of a mechanical pushbutton or switch.
Connection
Input En
Parameter
Output Q
Description
Output Q is set with a 0 to 1 signal transition at input En
(Enable) and if, in addition, 'Status=On' has been confirmed in configuration mode.
Type: Sets either a pushbutton action for one cycle or a switching action of the function.
Status: On or Off state that is applied in the initial cycle after program startup, is retentivity is not set.
Retentivity set (on) = the status is retentive in memory.
Output Q remains set 1, as long as En=1 and the status at the parameter Type = Switch and Status = On.
Output Q is set for the duration of one cycle if EN=1 and the status at the parameters Type = momentary (pushbutton) and Status = On.
198
The status of this switch can be changed momentarily in parameter mode. For information about how to modify, refer to chapter 5.2.2 please.
Factory state
Default of 'Type' is 'momentary action switch'.
Timing diagram
Description of the function
The output is set, when input En is set and the 'Status' parameter is set to 'On' and confirmed with OK. This action is performed irrespective of a configured switch or pushbutton function.
The output is reset to '0' in the following three cases:
With a 1 to 0 signal transition at input En.
When a pushbutton function is configured and one cycle has expired after its actuation.
When the 'Status' parameter sets the 'Off' status in configuration mode, and this has been confirmed with OK.
Particular characteristics to be noted when configuring
The softkey can be used both with momentary pushbutton or switching action. At the status parameter you can define the on (actuated) or off state for the switch/pushbutton.
If the softkey is assigned a pushbutton action, the output is always set for the duration of one cycle with a 0 to 1 transition at input En when the pushbutton is in on state, or if the pushbutton state changes from Off to
On when En=1.
6.5.20 Shift register
Short description
199
The shift register function can be used to read an input value and to shift the bits. The output value corresponds with the configured shift register bit. The shift direction can be changed at a special input.
Connection
Input In
Input Trg
Input Dir
Parameter
Output Q
Description
The function when started reads this input value.
The SFB is started with a positive edge (0 t 1 transition) at input Trg
(Trigger). A 1 to 0 transition is irrelevant.
You define the shift direction of the shift register bits
S1...S8 at the Dir input:
Dir = 0: shift up (S1 >> S8)
Dir = 1: shift down (S8 >>
S1)
Shift register bit that determines the value of output Q.
Possible settings: S1 ... S8
Retentivity set (on) = the status is retentive in memory.
The output value corresponds with the configured shift register bit.
Timing diagram
200
Description of the function
The function reads the value of input In with a positive edge (0 to 1 transition) at input Trg (Trigger).
This value is written to shift register bits S1 or S8, depending on the set shift direction:
Shift up: S1 accepts the value of input In; the previous value of S1 is shifted to S2,
S2 is shifted to S3, etc.
Shift down: S8 accepts the value of input In; the previous value of S8 is shifted to S7,
S7 is shifted to S6, etc.
Q outputs the value of the configured shift register bits.
If retentivity is not enabled, the shift function restarts at S1 or S8 after a power failure.
Note
The special function shift register can be used only once in the circuit program.
6.5.21 Analog comparator
Short description
The output is set and reset depending on the difference Ax - Ay and on two configurable thresholds.
201
Connection
Inputs Ax, Ay
Parameter
Output Q
Description
Input the analog signals of which you want to determine the delta at the inputs Ax and Ay.
Use the analog inputs AI1...AI8, the analog outputs
AQ1 and AQ2.
AI1..AI8: 0 - 10 V corresponds with 0 - 1000 (internal value).
A: Gain
Range of values: ± 10.00
B: Zero offset
Range of values: ± 10,000
On: On threshold
Range of values: ± 20,000
Off: Off threshold
Range of values: ± 20,000
p: Number of decimals
Range of values: 0, 1, 2, 3
Q is set or reset depending on the set thresholds.
Parameter p (number of decimals)
The on threshold On and the off threshold Off can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
Applies only to Ax, Ay, Delta, On and Off values displayed in a message text.
Does not apply to the comparison of on and off values! (The compare function ignores the decimal point.)
The value of "On","Off"and "Dec" can be set/modified in parameter mode.(Dec means decimal point.)
Timing diagram
202
Q for Ax - Ay > 200, On = Off = 200
Description of the function
The function reads the value of the signal at the analog input Ax.
This value is multiplied by the value of parameter A (gain). Parameter B (offset) is added to the product, hence
(Ax ∙ gain) + offset = Actual value Ax.
(Ay ∙ gain) + offset = Actual value Ay.
Output Q is set or reset depending on the difference of the actual values Ax - Ay and the set thresholds. See the following calculation rule.
Calculation rule
If threshold On ≥Threshold Off, then:
Q = 1, if (actual value Ax - actual value Ay) > On
Q = 0, if (actual value Ax - actual value Ay) ≤Off.
If threshold On < Threshold Off, then Q = 1, falls:
On ≤ (actual value Ax - actual value Ay) < Off.
Reducing the input sensitivity of the analog comparator
You can delay the output of the analog comparator selectively by means of the "on delay" and "off delay"
SFBs. By doing so, you determine that output Q is only set if the input trigger length Trg (= output of the analog comparator) exceeds the defined on delay time.
This way you can set a virtual hysteresis, which renders the input less sensitive to short changes.
Particular characteristics to be noted when configuring
For help on analog block parameters, refer to the Analog value processing section in eSmsConfig.
Example
In a heating control system, the supply Tv and return line temperatures Tr are to be compared, for example with a sensor at AI2.
A control signal is to be triggered (for example "heater On") when the difference between the
203
supply and return line temperatures is greater than 15 °C. The control signal is reset when the difference is less than 5 °C.
The process variable of the temperature is to be shown in parameter assignment mode.
The thermocouples available have the following technical data: -30 to +70 °C, 0 to 10 VDC.
Reducing the input response of the analog comparator
You can selectively delay the output of an analog comparator by means of the "On-delay" and "Off-delay" special functions. With on-delay, output Q is only set if the pulse width of the triggering signal at input Trg (=analog comparator output) is longer than the on-delay time.
Using this method, you will obtain a virtual hysteresis and reduce the input response to short signals.
Function block diagram
6.5.22 Analog threshold trigger
Short description
The output is set or reset depending on two configurable thresholds (hysteresis).
204
Connection
Input Ax
Parameter
Output Q
Description
Input the analog signal to be evaluated at input Ax.
Use the analog inputs AI1...AI8, the analog outputs AQ1 and AQ2.
0 - 10 V is proportional to 0 - 1000 (internal value).
A: Gain
Range of values: ± 10.00
B: Zero offset
Range of values: ± 10,000
On: On threshold
Range of values: ±20,000
Off: Off threshold
Range of values: ± 20,000
p: Number of decimals
Range of values: 0, 1, 2, 3
Q is set or reset depending on the set thresholds.
Parameter On and Off
The On and Off parameters can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
Applies only to the display of On, Off and Ax values in a message text.
Does not apply to the comparison of On and Off values! (The compare function ignores the decimal point.)
The value of "On","Off"and "Dec" can be set/modified in parameter mode. For information about how to set/modify.(Dec means decimal point.)
Timing diagram
205
Description of the function
The function reads the value of the signal at the analog input Ax.
This value is multiplied by the value of parameter A (gain). Parameter B (offset) is added to the product, hence
(Ax ∙Gain) + Offset = Actual value Ax.
Output Q is set or reset depending on the set threshold values. See the following calculation rule.
Calculation rule
If threshold (On) ≥ threshold (Off), then:
Q = 1, if the actual value Ax > On
Q = 0, if the actual value Ax ≤Off.
If threshold (On) < threshold (Off), then Q = 1, if
On ≤ the actual value Ax < Off.
Note
The decimal point setting must be identical in the min. and max. range.
Setting the Par parameter
The gain and offset parameters are used to adapt the sensors to the relevant application.
206
6.5.23 Analog amplifier
Short description
This SFB amplifies an analog input value and returns it at the analog output.
Connection
Input Ax
Parameter
Output AQ
Description
Input the analog signal to be amplified at input Ax.
Use the analog inputs
AI1...AI8, the analog outputs
AQ1 and AQ2.
AI1..AI8: 0 - 10 V corresponds with 0 - 1000 (internal value).
A: Gain
Range of values: ± 10.00
B: Zero offset
Range of values: ± 10000
p: Number of decimals
Range of values: 0, 1, 2, 3
Analog output
Value range for AQ:
-32768...+32767
Parameter p (number of decimals)
Applies only to the display of Ax and Ay values in a message text.
Does not apply to the comparison of On and Off values! (The compare function ignores the decimal point.)
Description of the function
The function reads the value of an analog signal at the analog input Ax.
This value is multiplied by the gain parameter A. Parameter B (offset) is added to the product, i.e.
(Ax ∙gain) + offset = Actual value Ax.
Setting the Par parameter
The gain and offset parameters are used to adapt the sensors to the relevant application.
207
6.5.24 Analog value monitoring
Short description
This special function saves the process variable of an analog input to memory, and sets the output when the output variable exceeds or drops below this stored value plus a configurable offset.
Connection
Input En
Input Ax
Parameter
Output Q
Description
A positive edge (0 to 1 transition) at input En saves the analog value at input Ax ("Aen") to memory and starts monitoring of the analog range Aen ± Delta.
You apply the analog signal to be monitored at input
Ax.
Use the analog inputs AI1...AI8, the analog outputs AQ1 and AQ2.
0 - 10 V is proportional to 0 - 1000 (internal value).
A: Gain
Range of values: ± 10.00
B: Zero offset
Range of values: ± 10,000
Delta: Difference value for the Aen on/off threshold
Range of values: ± 20,000
p: Number of decimals
Range of values: 0, 1, 2, 3
Q is set/reset, depending on the stored analog value and the offset.
Parameter p (number of decimals)
The two threshold parameters Threshold 1 and Threshold 2 can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
208
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
Applies only to the display of Aen, Ax and Delta values in a message text.
Timing diagram
Description of the function
A 0 to 1 transition at input En saves the value of the signal at the analog input Ax. This saved process variable is referred to as Aen".
Both the analog actual values Ax and Aen are multiplied by the value at parameter A (gain), and parameter
B (offset) is then added to the product, i.e.
(Ax ∙ gain) + offset = Actual value Aen, when input En changes from 0 to 1, or
(Ax ∙ gain) + offset = Actual value Ax.
Output Q is set when the signal at input En = 1 and if the actual value at input Ax is out of range of Aen ±
Delta.
Output Q is reset, when the actual value at input Ax lies within the range of Aen +- Delta, or when the signal at input En changes to lo.
Setting the Par parameter
The gain and offset parameters are used to adapt the used sensors to the respective application.
209
6.5.25 Analog differential trigger
Short description
The output is set and reset depending on a configurable threshold and a differential value.
Connection
Input Ax
Parameter
Output Q
Description
You apply the analog signal to be analyzed at input Ax.
Use the analog inputs
AI1...AI8, the analog outputs
AQ1 and AQ2.
0 - 10 V is proportional to 0 -
1000 (internal value).
A: Gain
Range of values: ± 10.00
B: Zero offset
Range of values: ± 10,000
On: On threshold
Range of values: ±20,000
Delta: Differential value for calculating the off parameter
Range of values: ± 20,000
p: Number of decimals
Range of values: 0, 1, 2, 3
Q is set or reset, depending on the threshold and difference values.
Parameter p (number of decimals)
Applies only to the display of On, Off and Ax values in a message text.
Does not apply to the comparison of On and Off values! (The compare function ignores the decimal point.)
Timing diagram A: Function with negative difference Delta
210
Timing diagram B: Function with positive difference Delta
Description of the function
The function fetches the analog signal at input Ax.
Ax is multiplied by the value of the A (gain) parameter, and the value at parameter B (offset) is added to product, i.e.
(Ax ∙ gain) + offset = actual value of Ax.
Output Q is set or reset, depending on the set (On) threshold and difference value (Delta). The function automatically calculates the Off parameter: Off = On + Delta, whereby Delta may be positive or negative.
See the calculation rule below.
Calculation rule
When you set a negative differential value Delta, the On threshold >= Off threshold, and:
Q = 1, if the actual value Ax > On
Q = 0, if the actual value Ax ≤ Off.
See the timing diagram A.
When you set a positive differential value Delta, the On threshold < the Off threshold, and Q = 1, if:
On ≤ the actual value Ax < Off.
See the timing diagram B.
Setting the Par parameter
The gain and offset parameters are used to adapt the sensors to the relevant application.
211
6.5.26 Analog multiplexer
Short Description
This special function displays 0 or one of 4 saved analog values on the analog output.
Connection
Input En
Inputs S1 and S2
Parameter
Output AQ
Description
1 on input En (Enable) switches, dependent on S1 and S2, a parameterized analog value to the output
AQ.
0 on input EN switches 0 to the output AQ.
S1 and S2 (selectors) for selecting the analog value to be issued.
S1 = 0 and S2 = 0: The value
1 is issued
S1 = 0 and S2 = 1: The value
2 is issued
S1 = 1 and S2 = 0: The value
3 is issued
S1 = 1 and S2 = 1: The value
4 is issued
V1...V4: Analog values
(Value) that will be issued.
Value range:
-32768...+32767
p: Number of decimal places value range: 0, 1, 2, 3
Analog output
Value range for AQ:
-32768...+32767
Parameters V1…V4
212
The values for V1…V4 can be provided by the value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
Timing Diagram
Description of Function
If input En is set, then the function issues one of 4 possible analog values V1 to V4 at the output AQ, depending on the parameters S1 and S2.
If the input En is not set, then the function issues the analog value 0 at output AQ.
Analog output
If you interconnect this special function with a real analog output, note that the analog output can only process values between 0 and 1000. To do this, you may need to connect an additional amplifier between the analog output of the special function and the real analog output. Using this amplifier, you standardize the output range of the special function to a value range of 0 to 1000.
Setting the Par parameter
213
6.5.27 System cover
This block cannot directly be found in the block list ,however, it is set as default by system of x-Messenger, hence system cover can be available if you follow the below procedures : use your mouse to left-click “Tools” menu->select “Edit Cover HMI” by left-click in eSmsConfig .
Short description
Display the status (Run or Stop) of x-Messenger when power-on or simulation by soft.
Particular characteristics to be noted when configuring
1."General" area
Here you will find the following settings:
A. Priority of the system cover
B. Check box for message text acknowledgment
2. "Messages" area
Users can edit the messages in the first and second line, the third line displays the state RUN or STOP, and the messages saying whether your program has mistakes or not will be shown in the fourth line.
3. "Delete" button
The button is used for deleting the “Messages” in the first and second line.
214
6.5.28 Pulse Width Modulator (PWM)
Short Description:
The Pulse Width Modulator (PWM) instruction modulates the analog input value Ax to a pulsed digital output signal. The pulse width is proportional to the analog value Ax.
connection
EN
Input Ax parameter
Output Q
Description
A positive edge (0 to 1 transition) at input En enables the PWM function block.
Analog signal to be modulated to a pulsed digital output signal.
A: Gain
Range of values: +- 10.00
B: Zero offset
Range of values: +- 10,000
PT: Periodic time over which the digital output is modulated
p: Number of decimals
Range of values: 0, 1, 2, 3
Q is set or reset for the proportion of each time period according to the proportion of the standardized value Ax to the analog value range.
215
Parameter PT
The periodic time PT can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
PI controller: AQ
Analog math: AQ
Data latching relay: AQ
Up/Down counter: Cnt
Parameter p (number of decimals)
Parameter p applies only to the display of the Ax value in a message text.
Description of the function
The function reads the value of the signal at the analog input Ax.
This value is multiplied by the value of parameter A (gain). Parameter B (offset) is added to the product, as follows:
(Ax * Gain) + Offset = Actual value Ax
The function block calculates the proportion of the value Ax to the range. The block sets the digital output Q high for the same proportion of the PT (periodic time) parameter, and sets Q low for the remainder of the time period.
Examples with Timing Diagrams
The following examples show how the PWM instruction modulates a digital output signal from the analog input value:
Example 1
Analog input value: 500 (range 0...1000)
Periodic time T: 4 seconds
The digital output of the PWM function is 2 seconds high, 2 seconds low, 2 seconds high, 2 seconds low and continues in that pattern as long as parameter "En" = high.
216
Example 2
Analog input value: 300 (range 0...1000)
Periodic time T: 10 seconds
The digital output of the PWM function is 3 seconds high, 7 seconds low, 3 seconds high, 7 seconds low and continues in that pattern as long as parameter "En" = high.
Calculation rule
Q = 1, for (Ax – Min) / (Max – Min) of time period PT
Q = 0, for PT – [(Ax – Min) / (Max – Min)] of time period PT.
Note: Ax in this calculation refers to the actual value Ax as calculated using the Gain and Offset. Min and Max refer to the minimum and maximum values specified for the range
Special feature.
Generally, the output frequency could be up to 30Hz But the Q3,Q4 of EXM-12DC-D/DA-TN type (PNP transistor output) CPU could be up to 333 Hz and the property dialog box of PWM function block setting as follows:
217
If the special output is selected in the property dialog box of PWM block, then the unit of “periodic time” will be changed from s:1/100s to s:1/1000s, so if you input 3 (1/1000s) , then its frequency is 1000/3 Hz.
Notes:
1. The periodic time must be no less than 3 ms.
2. If the specific output is selected in the property dialog box of PWM block, then the output pin of PWM function block cannot be linked as input to other blocks.
3. Q3, Q4 in the above dialog box are exactly corresponding to Q3, Q4 of EXM-12DC-D/DA-TN (PNP) CPUs
Setting the Par Parameter
The following illustration shows the view in programming mode that corresponds to the first example:
218
6.5.29 Analog Ramp
Short Description:
The Analog Ramp instruction allows the output to be changed from the current level to a selected level at a specified rate.
Connection
Input En
Input Sel
Input St parameter
Output AQ
Description
A change in the status from 0 to 1 at input EN (Enable) applies the start/stop level (Offset "B"
+ StSp) to the output for 100 ms and starts the ramp operation to the selected level.
A change in the status from 1 to 0 immediately sets the current level to Offset "B", which makes output AQ equal to 0.
SeI = 0: The step 1 (level 1) is selected.
SeI = 1: The step 2 (level 2) is selected.
A change in status of Sel causes the current level to start changing to the selected level at the specified rate.
A change in the status from 0 to 1 at input St (Decelerated Stop) causes the current level to decrease at a constant rate until the start/stop level (Offset "B" + StSp) is reached. The start/stop level is maintained for 100 ms and then the current level is set to Offset "B", which makes output AQ equal to 0.
Level1 and Level2: Levels to be reached; value range for each level: -10,000 to +20,000
MaxL: Maximum value that must not be exceeded.
Value range: -10,000 to +20,000
StSp: Start/Stop offset: value that is added to Offset "B" to create the start/stop level. If the
Start/Stop offset is 0, then the start/stop level is Offset "B").
Value range: 0 to +20,000
Rate: Speed with which level 1, level 2 or 0ffset is reached. Steps/seconds are issued.
Value range: 1 to 10,000
A: Gain
B: Offset
Value range: 0 to 10,00
Value range: +- 10.000
p: Number of decimal places
Value range: 0, 1, 2, 3
The output AQ is scaled using the formula:
219
(Current Level - Offset "B") / Gain "A"
Note: When AQ is displayed in parameter mode or message mode, it is displayed as an un-scaled value (engineering units: current level).
Value range for AQ: 0...+32767
Parameter p (number of decimal places)
The level parameters Level1 and Level2 can be provided by the value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
Parameter p only applies for displaying the values of AQ, level 1, level 2, MaxL, StSp, and Rate in a message text.
Timing diagram for AQ
Description of function
220
If the input En is set, then the function sets the value StSp + Offset "B" for 100 ms.
Then, depending on the connection of Sel, the function runs from the level StSp + Offset "B" to either level
1 or level 2 at the acceleration set in Rate.
If the input St is set, the function runs to a level of StSp + B at the acceleration set in Rate. Then the function holds the level at StSp + Offset "B" for 100 ms. After 100 ms, the level is set to Offset "B". output AQ. The scaled value (output AQ) is 0.
If the input St is set, the function can only be restarted once the inputs St and En have been reset.
If input Sel has been changed, depending on the connection of Sel, the function runs from the current target level to the new target level at the rate that is specified.
If the input En is reset, the function immediately sets the current level to Offset "B".
The current level is updated every 100 ms. Note the relationship between output AQ and the current level:
Output AQ = (current level – Offset "B" ) / Gain "A"
6.5.30 Analog Math
Short Description
The analog math block calculates the value AQ of an equation formed from the user-defined operands and operators.
Connection
Input EN
Parameter
Description
Enable the analog math function block.
V1:Value 1: First operand
V2: Value 2: Second operand
V3: Value 3: Third operand
V4: Value 4: Forth operand
Operator 1: First operator
Operator2: Second operator
Operator 3: Third operator
Priority 1: Priority of first operation
Priority 2: Priority of second operation
Priority 3: Priority of third operation
221
Output AQ
P: number of decimals
Range of values: 0,1,2,3
The output AQ is the result of the equation formed from the operand values and operators. AQ will be set to 32767 if a divide by 0 or overflow occurs, and -32768 if a negative overflow (underflow) occurs.
Parameter p (number of decimals)
The values V1, V2, V3, and V4 can be provided by the actual value of another already-programmed function:
Analog comparator: Ax – Ay
Analog trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Analog math: AQ
PI controller: AQ
Data latching relay: AQ
Up/Down counter: Cnt
Parameter p applies to the display of V1, V2, V3, V4 and AQ in a message text.
Description of the function
The analog math function combines the four operands and three operators to form an equation. The operator can be any one of the four standard operators: +, -, *, or /. For each operator, you must set a unique priority of High ("H"), Medium ("M"), or Low ("L"). The high operation will be performed first, followed by the medium operation, and then by the low operation. You must have exactly one operation of each priority. The operand values can reference another previously-defined function to provide the value. The analog math function rounds the result to the nearest integer value.
The number of operand values is fixed at four and the number of operators is fixed at 3. If you need to use fewer operands, use constructions such as " + 0" or " * 1" to fill the remaining parameters.
You can also configure the behavior of the function when the Enable parameter "En"=0. The function block can either retain its last value or be set to 0.
Possible errors: Zero division and overflow
If the analog math function block execution results in zero division or overflow, it sets internal bits that indicate the type of error that occurred. You can program an analog math error detection function block in your circuit program to detect these errors, and to control the program behavior as needed. You program one analog math error detection function block to reference one specific analog math function block.
222
Examples
The following tables show some simple example analog math block parameters, and the resulting equations and output values:
V1
12
Operator1
+(M)
Equation: (12 + (6 / 3)) - 1
Result: 13
V2
6
Operator2
/(H)
V3
3
Operator3
-(L)
V4
1
V1 Operator1
2 +(L)
Equation: 2+ (3*(1+4))
Result: 17
V2
3
Operator2
*(M)
V3
1
Operator3
+(H)
V4
4
V1
100
Operator1
-(H)
Equation: (100 – 25) / (2 + 1)
Result: 25
V2
25
Operator2
/(L)
V3
2
Operator3
+(M)
V4
1
6.5.31 Analog math error detection
Short Description
The analog math error detection block sets an output if an error has occurred in the referenced analog math function block.
Connection
Input EN
Input R
Parameter
Output AQ
Description
Enable the analog math error detection function block.
Reset the output
Referenced FB: block number of an analog math instruction
Error to detect: Zero division, Overflow, or Zero division OR Overflow.
Auto Reset: Reset the output when the failure condition clears.
Q is set high if the error to detect occurred in the last execution of the referenced analog math function block.
Parameter Referenced FB
223
The value for the Referenced FB parameter references the block number of an already-programmed analog math function block.
Description of the function
The analog math error detection block sets the output when the referenced analog math function block has an error. You can program the function to set the output on a zero division error, an overflow error, or when either type of error occurs.
If you select the automatically reset checkbox, the output is reset prior to the next execution of the function block. If not, the output retains its state until the analog math error detection block is reset with the R parameter.
In any scan cycle, if the referenced analog math function block executes before the analog math error detection function block, the error is detected in the same scan cycle. if the referenced analog math function block executes after the analog math error detection function block, the error is detected in the next scan cycle.
Analog math error detection logic table
In the table below, Error to Detect represents the parameter of the analog math error detection instruction that selects which type of error to detect. Zero represents the zero division bit set by the analog math instruction at the end of its execution: 1 if the error occurred, 0 if not. OF represents the overflow bit set by the analog math instruction: 1 if the error occurred, 0 if not. Zero division OR Overflow represents the logical
OR of the zero division bit and the overflow bit of the referenced analog math instruction. Output (Q) represents the output of the analog math error detection function. An “x” indicates that the bit can be either
0 or 1 with no influence on the output.
Error to
Detect
Zero division
Zero division
Overflow
0
X zero
1
X
1 of
X
0
1
Output
1
224
Overflow X
Zero division OR
Overflow
Zero division OR
Overflow
Zero division OR
Overflow
Zero division OR
Overflow
1
0
1
0
0
0
1
1
0
0
1
1
1
0
If the Referenced Analog Math FB is null, then the output is always 0.
6.5.32 Modbus Read
Short description:
When there is a high level at En, the Modbus Read block will be activated and the x-Messenger shall communicate with a peripheral device as a master via RS232 or RS485 interface. Furthermore, the output will be switched on when communication is established successfully. Otherwise the output (Q pin) remains “off” which means communication has failed.
A signal at input R resets output Q and disables this block at the same time
Connection
Input En
Input R
Description
A high signal at En input will enable “Modbus Read” function block to be activated
Reset the value read from peripheral and set the output to 0 via the R (Reset) input.
Reset has priority over En
225
Parameter
Output Q
Slave address: 1 is default .
Communication protocol: Modbus(RTU)
Communication parameter: baud rate (BPS),Data bits, Stop bits,
Parity, Overtime (response time out)
Comm Type: RS232 or RS485( Communication interface of x-Messenger )
Data register Index: High Low /Low High
Command: 01 Read coils(0x)
02 Read Discrete Input(1x)
03 Read Holding Registers(4x)
04 Read Input Registers(3x)
Register start address, count
Q is set or reset depending on the communication status.
Successful communication , Q=1;
Failed communication ,Q=0;
Note: 1.
Data register Index: High Low /Low High
For example, when High Low index was set, one data 0x 00 12 was read and saved to AQ, AQ= 0X0012; however, when Low High index was set, AQ=0x 1200
Regarding Modbus RTU detail, please refer to our Modbus RTU communication protocol file for it.
Description of the function:
In the configuration of our x-Messenger communication, the x-Messenger usually serves as a slave via
Modbus RTU Protocol, and can communicate with a master directly. That’s to say, any device communicating with x-Messenger sends command to it, and then its response will be sent out only when the x-Messenger has received the command, Just as the below figure shows:
However, the “Modbus Read” or “Modbus Write”(next chapter will introduce it) function block would be utilized if x-Messenger shall be required to play a role of master to communicate with other devices. As the following figure shows:
When you put the “Modbus read” or “Modbus Write” function block in your program and make some
226
configurations, the function that x-Messenger serves as master will be realized.
The Property in dialog box of “Modbus Read” shows as below figure:
1. Slave Address: 1 is default
2. Communication parameters:BPS is baud rate、Stopbits、Databits、Communication type:
RS232、RS485 . Actually RS232 or RS485 are just interface of x-Messenger.
3. Command, register address and register count
227
Command
01
02
03
Function description
Read one group coil status(00000~0XXXX) remark
Read Coil Status(output)
Fetch one group data of the status of switch input
( 10000~1XXXX)
Read input Status (input relay)
Read data of multi-holding register(40000~4XXXX) Read Holding Registers
04 Read data of input registers (3000~3XXXX)
(Output register)
Read Input Registers
Note: Please use “03” command to read AI/AO of x-Messenger
4. Where to save the data read from Slave.
Example: The following we'll take a example that one x-Messenger (Master) communicate with other x-Messenger (Slave) via RS485.
Example 1: Get Q1 status of SLAVE1(x-Messenger) and then save the bit status to F1.
228
If count was set 4, the Q1,Q2,Q3,Q4 of x-Messenger (station No.1) will be read and save to F1 to F4
F is bit type flag. It can be used to receive bit data from slave device.
Example 2 : Get AI value from Slave 2(x-Messenger with station No.2) and save the data to AQ11
229
The number setting of Q,I,AQ are continuous .AQ12 cannot be set as AQ 12 and should be set AQ 4 as above figure shows.
The following table shows how to set.
Note: this table also can be applied for the configuration of Modbus Write function block.
230
Model
CPU
Expansion1
(Address is 1)
Expansion2
(Address is 2
I,Q,AI,AQ
I1-I8
Q1-Q4
AI1—AI8
AQ1—AQ2
I11-I14
Q11-Q14
AI11-AI14
AQ11-AQ12
I21-I24
Q21-Q24
AI21-AI24
AQ21-AQ22
…………….
Dialog box set
I1-I8
Q1-Q4
AI1—AI8
AQ1—AQ2
I9-I12
Q9-Q12
AI9—AI12
AQ3,AQ4
I18—I21
Q17—Q19
AI17---AI24
AQ5--AQ6
Data format instruction
231
6.5.33 Modbus Write
Short description:
When a high level in En, the Modbus Write block will be activated and the x-Messenger could communicate with peripheral as a master via RS232 or RS485 interface, further the output will be switched on when the communication is established successfully. Otherwise the output (Q pin) is kept“off” it means communication has failed.
A signal at input R resets output Q and disable, this block at the same time
Connection
Input En
Input R
Parameter
Output Q
Description
A high signal at En input will enable “Modbus Write” function block to be activated
Reset the value read from peripheral and set the output to 0 via the R (Reset) input.
Reset has priority over En
Slave address: 1 is default .
Communication protocol: Modbus(RTU)
Communication parameter: baud rate (BPS),Data bits, Stop bits,
Parity, Overtime (response time out)
Comm Type: RS232 or RS485( Communication interface of x-Messenger )
Data register Index: High Low /Low High
Command: 05 Write Single Coil
06 Write Single Register
15 Write Multiple Coils
16 Write Multiple Registers
Register start address, count
Q is set or reset depending on the communication status.
Successful communication , Q=1;
Failed communication ,Q=0;
232
The Property in dialog box of “Modbus Write” shows as below figure:
1. Slave Address: 1 is default
2.Communication parameters:BPS is baud rate、Stopbits、Databits、Communication type: RS232、RS485 .
Actually RS232 or RS485 are just interface of x-Messenger.
3. Command, register address and register count
Command Function description
05 remark
Force the switch status of single coil(00000~0XXXX) Force Single Coil
06
15
16
Pre-set the data of single register
( 40000~4XXXX)
Force multi-coils on/off bit(00000~0XXXX)
Write multi-holding registers data(40000~4XXXX)
( output)
Set single output register
233
4. Where is to save the pre-configuration data that would be written to Slave. It contains 2 kind ways to pre-configuration. One is auto mode, this data uses the flags in the program, such as FM, AFM, I, Q and AQ.
The manual mode is input a fixed value or bit status.
Example 1
Write the I2 bit status of Master x-Messenger to Slave x-Messenger with No.1 and control Q1 of Slave via
RS485 port. The program of master can be made as follows:
234
I1of master is used to control the communication .If I1 is high and the communication is established successfully, one alarm message (text message block) will be displayed on LCD. Then the Q1 of slave No.1
will be controlled by I2 of master. If I2 is high, Q1 of slave No.1 would be ON and if I2 is low, Q1 of slave would be OFF.
Note: The Q1 must be free, it means the in the program of Slave No.1, the input pin of Q1 must be not linked to other blocks.
Example 2, manual mode input value
The above configuration is to force Q1, Q2, Q3 of Slave No.1 ON. " " means pre-set the BIT 1 and
" " means pre-set the BIT 0 ”Coil 0” is corresponding to the start address ,Here is Q1.
Note: The manual input value is Hex data .it contains 4 bytes. If you want to write a decimal value to the register of SLAVE, please convert it to Hex format.
235
4. The following table shows how to set.
Note: this table also can be applied for the configuration of Modbus Read function block
Data format instruction
For the detail information about I, AI, Q, AQ, registers address of x-Messenger ,refer to the RTU protocol file.
6.5.34 Data latching relay
Short description
This special function saves the process variable of an analog input to memory, and returns it at the analog output.
236
Example
Connection
Input S
Input Ax
Input R
Output AQ
Description
Save the Ax to memory and return it at the analog output with a signal at input S (Set).
Input the analog signal to be amplified at input Ax. Use the analog inputs, the block number of a function with analog output, or the analog outputs.
Reset analog output AQ to 0 with a signal at input R (Reset).
analog Output AQ is reset if S and R are both set (reset has priority over set).
Analog output
Value range for AQ: -32768...+32767
When I1 turn to HIGH, the value of AI2 will be saved to memory and return it to AQ1 as follows:
When the I3 turns to HIGH, the value of this function block will be reset to 0.
237
6.5.35 PI controller
Short Description
It is proportional-action and integral-action controllers. You can use both types of controller individually or combined.
Connection
Input A/M
Input R
Input PV
Parameter
Description
Set the mode of the controller:
1: automatic mode
0: manual mode
Use the input R to reset the output AQ. As long as this input is set, the input A/M is disabled. The output AQ is set to 0.
Analog value: process value, Influences the Output
Sensor: Type of sensor being used
Min.: Minimum value for PV value range: -10,000 to +20,000
Max.: Maximum value for PV value range: -10,000 to +20,000
A: Gain
Value range: +- 10.00
B: Offset
Value range: +- 10,000
SP: Set-value assignment value range: -10,000 to +20,000
238
Mq: Value from AQ with manual mode.
Value range: 0 to 1,000
Parameter sets: application-related presets for KC, TI and Dir (see below)
KC: Gain value range: 00.00 to 99.99
TI: Integral time value range 00:01 min to 99:59 min
Dir: Action direction of the controller value range: + or -
p: Number of decimal places value range: 0, 1, 2, 3
Output AQ Analog output (manipulated variable)
Value range for AQ: 0 to 1,000
Parameter P (number of decimal places)
Only applies for portraying the values from PV, SP, Min. and Max. in a message text.
Timing Diagram
The nature, manner and speed with which the AQ changes depends on the parameters KC and TI. Thus, the course of AQ in the diagram is merely an example. A control action is continuous; therefore the diagram portrays just an extract.
239
1.
A disturbance causes the PV to drop, as Dir is positioned upwards, AQ increases until PV corresponds again to SP.
2.
A disturbance causes the PV to drop, as Dir is positioned upwards, AQ decreases until PV corresponds again to SP.
Dir is coordinated to the basic conduct of a control loop. The direction (dir) cannot be changed during the term of the function. The change in Dir here is shown for the purposes of clarification.
3.
As AQ is set to 0 by means of the input R, PV changes. This is based on the fact that PV increases, which on account of Dir = upwards causes AQ to drop.
Description of Function
If the input A/M is set to 0, then the special function issues output AQ with the value that you set with parameter Mq.
If the input A/M is set to 1, then automatic mode commences. As an integral sum the value Mq is adopted, the controller function begins the calculations in accordance with the formulas given in Control and regulate basics. The updated value PV is used to calculate in the formulas.
Updated value PV = (PV * gain) + offset
If the updated value PV = SP, then the special function does not change the value of AQ.
Dir = upwards/+ (timing diagram numbers 1 and 3)
If the updated value PV > SP, then the special function reduces the value of AQ.
If the updated value PV < SP, then the special function increases the value of AQ.
Dir = downwards/- (timing diagram number 2)
If the updated value PV > SP, then the special function increases the value of AQ.
If the updated value PV < SP, then the special function reduces the value of AQ.
With a disturbance, AQ continues to increase / decrease until the updated value PV again corresponds to SP. The speed with which AQ changes depends on the parameters KC and
TI. If the input PV exceeds the parameter Max., then the updated value PV is set to the value of Max.. If the PV falls short of the parameter Min., then the updated value PV is set to the value of Min.
If the input R is set to 1, then the AQ output is reset. As long as R is set, the input A/M is disabled.
240
Sampling Time
The sampling time is fixed at 500 ms.
Parameter sets
In order to simplify the use of the PI controller, the parameters for KC, TI and Dir are already given as sets for the following applications:
Parameter set
Temperature fast
Application example
Temperature, cooling control of small spaces; small volumes
Parameter KC Parameter TI
(s)
0,5 30 +
Parameter
Dir
120 + Temperature slow Heating, ventilation, temperature, 1,0 cooling control of large spaces; large volumes
Pressure 1
Pressure 2
Full level 1
Quick pressure compressor control change, 3,0
Slow pressure change, differential 1,2 pressure control (flow controller)
Vat and/or reservoir filling without 1,0 drain
5
12
1
+
+
+
Full level 2 Vat and/or reservoir filling with 0,7 drain
20 +
Characteristics when configuring
Observe the Control and regulate basics.
Control and regulate
In engineering, quantities can be both controlled and regulated.
When controlling, a quantity is manipulated without being able to compensate for outside influences. When regulating, a quantity is maintained at a specific value in order to compensate for outside influences.
In the following example, controlling means that the person can set the heat output at a fixed value. The heater cannot compensate for the drop in room temperature when a window is opened.
In the example below, regulating means that the person can increase the heat output if the room temperature drops to below 20 °C. If the room temperature rises above 20 °C, the heat output is reduced.
241
Basic concepts of regulating
In the example, the current for the electric heating is the manipulated variable. The changeable resistance is the actuator. The hand that operates the actuator is the control. The actual room temperature is the controlled variable or the process value. The desired room temperature is the command variable or the setpoint value. The electric heating is the control process. The thermometer is the sensor. The temperature loss from opening the window is the disturbance variable.
So this means that the person measures the process value (room temperature) with the sensor
(thermometer), compares the process value (room temperature) with the command variable (desired room temperature) and uses the actuator (changeable resistance) to manually regulate the manipulated variable
(heating current), in order to compensate for the disturbance variable (temperature drop from opening the window). The person is therefore the controller.
242
The control device is formed from the actuator and the control.
The control and controller together form the regulating device.
The following picture gives an abstract portrayal of the situation described above.
The comparing element uses the sensor to compare the command variable with the process value. If the command variables and process value deviate from one another, this results in a positive or negative loop error that in turn changes the process value.
Control loop
The process value x influences the manipulated variable M by means of the regulating device. This creates a
243
closed circuit that is also known as a control loop.
If, in the example above, the window is opened, the temperature in the room drops. The person must increase the heat output of the heater. If the heat output is increased too much, it will get too hot. The person must then reduce the heat output.
If the heat output is increased or reduced too quickly, then the control loop starts to sway. The room temperature fluctuates. It is either too hot or too cold. To prevent this, the person must carefully and slowly reduce or increase the heat output.
Loop error
The loop error is the difference between the command variable and the process value. In other words: the deviation of a process value from a set value.
e = SP – PV
The loop error e brings about a change to the manipulated variable M.
The example above illustrates this very well: if, with a desired temperature of 20 °C (= command value w), the room temperature is 22 °C (= process value PV), this results in the loop error: e = SP – PV = 20 °C - 22 °C = -2 °C
In this case, the negative sign indicates a reversing action: the heat output is reduced.
In a control loop's state of equilibrium, the loop error is zero or very small. If the command variable changes or there is a disturbance, a loop error arises. The loop error is corrected by means of the manipulated variable
M.
Controller basics
A controller can be simply portrayed as follows:
The comparing element and the controller function describe the conduct of the controller.
The following describes the most important types of controller. A controller's step response tells us a lot about its conduct. The step response describes how a controller reacts to the erratic change in the process value.
There are 3 important basic types of controller:
Proportional-action controller (P controller)
Integral-action controller (I controller)
Differential-action controller (D controller – we're not touching on this here)
These are combined for a real controller. For instance, the PI controller:
244
P Controller
A proportional-action controller (P controller) changes the manipulated variable M proportional to the loop error. The P controller works immediately. By itself it cannot drive the loop error to zero.
:Manipulated variable of the P controller at the time n
:Gain of the P controller
: Loop error at the time n
The following picture shows a jump in process value and step response of the controller:
Summary
The P controller has the following characteristics:
It cannot correct faults with the control process > lasting loop error.
It reacts immediately to a change in the process value.
It is stable.
I Controller
An integral-action controller (I controller) changes the manipulated variable M proportional to the loop error and to the time. The I controller works by delayed action. It completely remedies a loop error.
In order to calculate the value of the manipulated variable at a period of time n, the time up until this period of time must be divided into small time slices. The loop errors at the end of each time slice must be added up
(integrated) and they are then entered in the calculation.
: Manipulated variable of the I controller at the time n
: Manipulated variable of the I controller at the time n-1; also called integral sum
: Gain of the I controller
: Sampling time, duration of a time slice
245
: Integral time: by means of this time, the influence of the integral part is controlled on the manipulated variable, also known as integral-action time
: Loop error at the time n
: Loop error at the time n-1; etc.
: Loop error at the beginning of the calculations
The following picture shows a jump in process value and step response of the controller:
Summary
The PI controller has the following characteristics:
It sets the process value exactly to the command variable.
By so doing, it tends to oscillate and is unstable.
It requires more time to carry out the control action than the P controller .
PI controller
A PI controller reduces the loop error immediately and will eventually drive the loop error to zero.
: Manipulated variable at the time n
: Proportional part of the manipulated variable
: Integral part of the manipulated variable
: Manipulated variable of the I controller at the time n-1; also called integral sum
246
: Gain of the P controller
: Gain of the I controller
: Sampling time, duration of a time slice
: Integral time; by means of this time the influence of the integral part is controlled on the manipulated variable, also known as the integral-action time
: Loop error at the time n
The following picture shows a jump in process value and step response of the controller:
Summary
The PI controller has the following characteristics:
The P controller components quickly intercept an occurring loop error.
The I controller components can then remedy the remaining loop error.
The controller components supplement each other so that the PI controller works quickly and precisely.
Description of the individual parameters
Controller parameters
Mn Manipulated variable at the time n
Portrayed in x-Messenger
Output of the PI controller block
Possible value range in the x-Messenger
0 to 1,000
247
kP
Gain of the P part kI
Gain of the I part
In the x-Messenger, the parameter
KC applies as an increase for the I part and the P part of the controller equally.
Should you enter KC=0, then the P part of the controller switches off. In this special case, k is automatically set to 1 for the I part. If KC = 0: kP =
0 and kI = 1
0.00 to 99.99
If KC <> 0: kP = kI = KC
Fixed 500 ms Ts Sampling time, duration of a time slice
TI Integral time en
Parameter TI, if you set this parameter to 99:59 min, then you switch off the I part of the controller.
Refer to SP and PV
00:01 min to 99.59 min
"
Loop error at the time n; generally applies: e = SP –
PV
SP
PV
The parameter SP is the set-value assignment w. For this parameter you can use the analog output of a different special function.
PV is the process value x and is calculated as follows:
-10,000 to +20,000
"
PV = (analog value on input * gain) + offset.
You can connect the input for example by means of an analog input with a PT100 sensor.
The gain parameter has an effect on
PV
The offset parameter has an effect on
PV
0.0 to 10.0
-10,000 to +20,000
248
PV is restricted by the parameters
Min. and Max.
The Dir parameter gives the action direction of the controller.
Positive means: If set value > process value then the process value is increased; if set value < process value then the process value is reduced.
Negative means: If set value > process value then the process value is reduced; if set value < process value then the process value is increased.
e.g. heat regulation: if the set value is greater than the process value (room is too cold), the manipulated variable increases the process value.
In each case: -10,000 to +20,000
- or +
6.5.36 Memory write
Short Description
Only when there is a low to high trigger at Trg pin, the Memory Write block will be activated and the pre-configured record action will be performed, at the same time the output will switch on if the record action had been done successfully.
Connection Description
Trg input Only when there is a low to high trigger at Trg pin, the Memory write Read block will be activated and the pre-configured record
249
Input R
Output Q action will be performed. Each trigger, only write once.
Reset the Memory Write block and set the output to 0 via the R
(Reset) input. Reset has priority over Trg
Q switches on only after Write function had been executed correctly.
Description of Memory write block’s property dialog box :
1. File name
Place where you can set the name of the file used to save the registers’ data
2. Record title
Below is an example in the “OUTPUT.TXT”
The above range circled in red is just pre-set contents in the “Record title” of the Memory write block’s
250
property dialog box.
3. File write mode
Two options available: Option A. Append (This option would be selected if a certain file is already existed in the Mini SD card inserted in ELC -MEMORY)
B . Create ( This option shall be chosen, if no any file existed or existed file has different name from that pre-set in the “file name” in the Mini SD card inserted in EXM-MEMORY has been ticked ,the file content will show the time when the data starts to be recorded.
If such box
4. Separator
Such separator shall be required while more than one analog values would be stored and displayed for easier observation and convenient analysis.
5. File Size
It is an option for you to set the size of file to be stored.
6. After memory Full
Two options can be selected after memory is full (it means the relative file has reached its pre-configured size), one is to over-write and the other is to stop recording.
7. Register params:
This section is for register’s parameters setting. The register includes following sorts:
A. I digital inputs
Name
I1-I8
I11-I14
I21-I24
…..
B. Q digital outputs
Address:
0….7
8---15
16…23
……
Name Address:
251
Q1-Q4
Q11-Q14
Q21-Q24
…..
C. F digital flag
0….7
8---15
16…23
……
Name
F1-F64
D. M
Address:
0….63
Name
M1-M512
F.
AI analog inputs
Address:
0….511
Name
AI1-AI8
252
Address:
0….7
AI11-AI14
AI21-AI24
…..
G. AQ analog outputs
8---15
16…23
……
Name
AQ1-AQ2
AQ11-AQ12
AQ21-AQ22
…..
G. AF analog flag
Address:
0….1
2---3
4…5
……
I. AM
Name
AF1-AF64
Address:
0….63
253
EXAMPLE:
Name
AM1-AM512
Address:
0….511
Please refer the property dialog box of B003, it can record the output status .The start address is from 0 and it must record the 20 outputs with continuous addresses.
And the record file shows below:
Per the program, every 6 seconds the record will do once, and the Q1, Q2, Q3, Q4, Q11 will be all “ON”. You can see the record file and you’ll see the recording time and the status of the output.
254
Note: 1.The ELC-MEMORY only can be inserted into the RS232 port ( programming port) of EXM series CPU.
2.If this function block is working ,the RS232 port ( programming port) will be occupied ,some data will be being transferred , if you want to use the programming port for some purposes (for example download or upload program) , you must make sure the Trg pin of this block keeps at Low status or stop the CPU by panel key.
6.5.37 Memory Read
Short Description
Only when there is a low to high trigger at Trg pin, the Memory Read block will be activated once and x-Messenger CPU will read correlative data (bit or short) to set pre-configured register from the file in the SD card of ELC-MEMORY module, at the same time the output will switch on if the read action had been done successfully.
Connection
Trg input
Input R
Output Q
Description
Only when there is a low to high trigger at Trg pin, the Memory
Read block will be activated and x-Messenger CPU will read some data (bit or short) to set pre-configured register from the file in the
SD card of ELC-MEMORY module. Each trigger, only write once.
Reset the Memory Read block and set the output to 0 via the R
(Reset) input.
Reset has priority over Trg
Q switches on only after the Read function had been executed correctly, provided.
Description of Memory write block’s property dialog box:
255
1. File name
The name of the file which you want to access is stored in the mini-SD card of the EXM-MEMORY module.
2. Record Title
Below is an example in the “OUTPUT.TXT”
3. Data Type:
Two options available: Option A. BIT (0 or 1, this is used to be set the status of Q or F )
Option B . WORD (this is used to be set the value of AQ or AF)
4. Record Index:
Here is used to set which line the CPU will access via this Memory Read block
4. Register Params
Here is to set the parameters of register, all these registers have “write” property.
BIT data can be used to set the register “Q” and “F”.
Q: digital outputs
256
F: digital flag
Name
Q1-Q4
Q11-Q14
Q21-Q24
…..
Address:
0….7
8---15
16…23
……
Name
F1-F64
Address:
0….63
WORD data can be used to set the register “AQ” and “AF”
AQ analog outputs
Name
AQ1-AQ2
AQ11-AQ12
AQ21-AQ22
…..
Address:
0….1
2---3
4…5
……
AF analog flags
Name
AF1-AF64
Address:
0….63
Count
Here is to set how many register you want to set once.
257
For example
If the Memory Read block had been triggered, the Q1 of ELC-12 CPU will be set “1”.
258
, .
6.5.38 Word to Bit
Short description
This special function is used to transfer the word type data (AI, AF or AQ) to 16 bit status (0 or 1)(F or Q)
Connection
Input En
Input R
Parameter
Output Q
Description
Enable this function.
Reset output Q with a signal at input R (Reset).
Retentivity set (on) = the status is retentive in memory.
Q is switched on with a signal at input En, and switched off with a low signal at input En.
Example1:
259
Convert the AQ11 (2012) to Q1,Q2 and F1--F14(0000011111011100)
Example2:
Convert the counter value (5) to Q1,Q2 and F1--F14(0000000000000101)
260
6.5.39 Bit to Word
Short description
This special function is used to transfer the 16-Bit status(0 or 1)(F or Q) to word type data (AF or AQ).
Connection Description
Input En
Input R
Enable this function.
Reset output AQ with a signal at input R (Reset).
Parameter Retentivity set (on) = the value is retentive in memory when power lost.
Output AQ AQ will output the value of the block when En was activated.
For example
Transfer the F1--F3 and Q1 status to the AQ001. F1 is saved in Bit0, F2 is saved in Bit1,F3 is saved in Bit2,Q1 is saved in Bit3.
261
1
0
1
0
1
0
1
0
1
F1
0
0
1
0
1
0
1
1
0
0
0
0
1
0
1
1
F2
0
0
0
1
1
1
1
1
0
0
1
1
1
0
0
0
F3
0
1
1
0
0
1
1
0
1
1
0
0
0
Q1
0
0
0
0
1
1
1
1
1
1
7
8
9
4
5
6
AQ1 value
0
1
2
3
10
11
12
13
14
15
262
Notes:
1.The Bit4--Bit15 was not ticked, they are all recognized as 0.
2. With such block you can realize to modify one bit of the word register in the slave devices together with the code 06/16 in Modbus network.
263
6.5.40 Device Reset
Short description
This function block is used to reset the device (Ethernet modem or WIFI modem built-in) in the CPU, if there is a trigger at the Trg pin. It merely can be applied to the CPU with Ethernet module or Wifi module built-in.
Available in below CPUs:
EXM series type:
EXM-12DC-DA-R-N
EXM-12DC-DA-RT-WIFI
EXM-12DC-DA-RT-GWIFI
Connection
Trg
Parameter
Output
Description
If there is a trigger at the Trg pin, then the Ethernet modem will be reset , The modem will be startup again until the time "Reset period" reached.
Channel: Ethernet
Reset period:1—100s
When the Ethernet module had been reset successfully, this block will output a short trigger.
.
Description of the function
In order to monitor the communication status of the Ethernet to see if it is normal or continuous(or avoid the
Ethernet module is dead by unknown cause), sometimes we need reset the Ethernet module built-in in the
CPU when the communication has failed or been timeout.
Just one parameter to be set is the "Reset period" as follows:
Here are two examples with detailed description on how to use these blocks in the program.
Example 1
264
Just as below program shows, after the CPU running, we can push down the digital input1(just need a short trigger to reset the Ethernet modem), after the Reset period(here is 5s) is reached, the Ethernet modem will start up and this block will output a short trigger at the same time.
Example2
We also can use such “device reset” block along with the “Com status” function block together in the program, when there is no data transmission through the Ethernet port while the timeout period(50s) is reached, the com port status will output HI signal ,and then the Device reset block would be enabled and the Ethernet module will be reset for the Reset period in the device reset block property dialog box.
6.5.41 Comport Status
Short description
This function block is used to monitor the communication status of the RS232 (programming port), RS485 port, Ethernet/WIFI port.
With the text message block, we can insert the com port status from such function block for displaying on the
LCD.
265
Connection
En
Parameter
Output
Description
Enable the function block if a HI level at En input pin and if a trigger from HI to
LOW, the function would be disabled.
Channel: RS232
RS485
Ethernet/WIFI
Timeout:1—100s
Monitor type: TX
RX
TX+RX
When a HI level at the En pin and the timeout is reached the output will be HI, and it will be reset when the En is switched.
Parameters
Channel
RS232: This channel is the programming port, it can be used to monitor or display the communication status of the below accessories:
ELC-RS232 cable
ELC-USB cable
PRO-RS485 cable
266
ELC-MEMORY
ELC-Copier
RS485: This channel is the RS485 port, it can be used to monitor or display the communication status of the below accessories:
EXM-12 Series
EXM-E-RS485
Ethernet/WIFI: This channel is the Ethernet/WIFI port, it can be used to monitor or display the communication status of the LAN port built-in in the CPU:
EXM Series
EXM-12DC-DA-R-N
EXM-12DC-D-R-N
EXM-12DC-DAI-R-N
EXM-12DC-DA-RT-WIFI
EXM-12DC-DA-RT-GWIFI
Timeout 1—100s
Monitor type
Tx : Data from CPU to external devices.
Rx: Data from external device to CPU
Tx+Rx: Data transmission between external device and CPU.
Description of the function
In order to monitor the communication status of the RS232, RS485 and Ethernet port, we can enable such function block, when the timeout period exceeds, such block shall output a high level trigger.
How to insert the com port status to the text message for displaying?
Put the “com port status” into program.
267
Select “BLOCKS” in the text message property block.
select TX or Rx and insert into the screen.
You can edit the text in the screen, such as TX:,RX:
So, you can view the communication status on the LCD, even if there are no indicators on the
ELC-RS232/ELC-USB/PRO-RS485.
268
If there is data transmission, the status of the com port on the LCD will be flashing.
6.5.42 Analog filter
Short Description
Connection
Input Ax
Parameter
Output AQ
Description
Analog Inputs
Analog Outputs
Analog Flags
The block number of a function with analog output
Sn (Number of samples): determines how many analog values are sampled within the program cycles that are determined by the set number of samples. x-Messenger samples an analog value within every program cycle. The number of program cycles is equal to the set number of samples.
Possible settings:
8, 16, 32, 64, 128, 256
AQ outputs an average value of the analog input Ax over the current number of samples, and it is set or reset depending on the analog input and the number of samples.
* Analog inputs: 0 to 10 V corresponds with 0 to 1000 (internal value).
Parameter
You can set the number of samples to the following values:
269
After you set the parameter, the analog filter calculates the average value of the samples and assigns this value to AQ.
Timing diagram
Description of function
The function outputs the average value after sampling the analog input signal according to the set number of samples. This SFB can reduce the error of analog input signal.
Note
There are a maximum of eight analog filter function blocks available for use in the circuit program in eSmsConfig
6.5.43 Max/Min
270
Short description
The Max/Min function block records the maximum or minimum value.
Connection
Input En
Input S1
Input Ax
Parameter
Output AQ
Description
The function of input En (Enable) depends on the settings of parameter Mode and the selection of check box "when En = 0, reset Max/Min".
This input is enabled when you set Mode =2:
A positive transition (0 to 1) at input S1 sets the output AQ to the maximum value..
A negative transition (1 to 0) at input S1 sets the output AQ to the minimum value.
Input Ax is one of the following analog signals:
Analog Inputs
Analog Outputs
Analog flags
Block number of a function with analog output
Mode
Possible settings: 0, 1, 2, 3
Mode = 0: AQ = Min
Mode = 1: AQ = Max
Mode = 2 and S1= 0 (low): AQ = Min
Mode = 2 and S1= 1 (high): AQ = Max
Mode = 3 or a block value is referenced: AQ = Ax
AQ outputs a minimum, maximum, or actual value depending on the inputs, or is reset to
0 if configured to do so when function is disabled
Analog inputs: 0 to 10 V corresponds with 0 to 1000 (internal value).
Parameter Mode
You can set the values for parameter Mode based on the actual values of another already-programmed function:
Analog comparator: Ax - Ay
Analog threshold trigger: Ax
Analog amplifier: Ax
Analog multiplexer: AQ
Analog ramp: AQ
Mathematic instruction: AQ
Up/Down counter: Cnt
Threshold trigger: Fre
Max/Min: Ax
PI controller: AQ
271
Analog filter : AQ
Average value : AQ
You can select the required function by the block number.
Timing diagram
*) If you select the check box "when En = 0, reset Max/Min"
Description of the function
If you select the check box "when En = 0, reset Max/Min":
En = 0: The function sets the AQ value to 0.
En = 1: The function outputs a value at AQ, depending on the settings of Mode and S1.
272
If you do not select the check box "when En = 0, reset Max/Min":
En = 0: The function holds the value of AQ at the current value.
En = 1: The function outputs a value at AQ, depending on the settings of Mode and S1.
Mode = 0: The function sets AQ to the minimum value
Mode = 1: The function sets AQ to the maximum value
Mode = 2 and S1 = 0: The function sets AQ to the minimum value
Mode = 2 and S1 = 1: The function sets AQ to the maximum value
Mode = 3 or a block value is referenced: The function outputs actual analog input value.
Max/Min block upper/lower function
In the dialog box of Max/Min block, there is a upper/lower limit setting, when the block output the AQ value is less than the lower value, the AQ shall be equal to the Lower value; While the block output the AQ value is more than the upper value, the AQ shall be equal to the upper value.
If someone wants to use the upper/lower limitation for other function blocks.
such upper/lower limit function can be used, then this block can be referenced as other blocks parameters when programming.
Here is an example:
Someone wants to use the panel key to change the on-delay parameters for 1s—10s in the text message block, if the value which user set exceeds such range, then it will crush the machine, hence we must add the upper/lower limitation in the program to avoid such trouble.
273
6.5.44 Average value
Short description
The average value function samples the analog input signal during configured time period and outputs the average value at AQ
Connection
Input En
Input R
Input Ax
Parameter
Description
A positive edge (0 to 1 transition) at input En (Enable) sets the output AQ to the average value of input Ax after the configured time. A negative edge (1 to 0 transition) holds the output at its last calculated value.
A positive edge (0 to 1 transition) at input R (Reset) resets the output AQ to 0.
Input Ax is one of the following analog signals:
Analog Inputs
Analog Outputs
Analog Flags
The block number of a function with analog output
St (Sampling time): You can set it to Seconds, Days, Hours or Minutes.
Range of values:
If St = Seconds: 1 to 59
If St = Days: 1 to 365
If St = Hours: 1 to 23
If St = Minutes: 1 to 59
Sn (Number of samples):
Range of values:
If St = Seconds: 1 to St*100
If St = Days: 1 to 32767
If St = Hours: 1 to 32767
If St = Minutes and St ≤ 5 minutes: 1 to St*6000
If St = Minutes and St ≥ 6 minutes: 1 to 32767
Output AQ
AQ outputs the average value over the specified time of sampling.
* Analog Inputs: 0 to 10 V corresponds with 0 to 1000 (internal value).
Parameter St and Sn
Parameter St represents the sampling time and parameter Sn represents the number of samples.
274
Timing diagram
Description of the function
When En = 1, the average value function calculates the average value of the samples during the configured time interval. At the end of the sampling time, this function sets output AQ to this calculated average value.
When En = 0, the calculation stops, and AQ retains the last calculated value. When R = 0, AQ is reset to 0.
6.5.45 Astronomical clock
Short description
The astronomical clock SFB is used to set an output high between sunrise and sunset based on the local time at the geographical location of the x-Messenger devices. The output status of this function block also depends on the configuration of summer time/wintertime conversion.
Connection Description
Output Q
Q is set to hi when sunrise time is reached. It holds this state until sunset time is reached.
Parameter
275
In the astronomical clock dialog, you can select the location of the x-Messenger device. You can select one of following pre-defined time zone locations:
Beijing
Berlin
London
Rome
Moscow
Tokyo
Washington
Ankara
Madrid
Amsterdam
If you select one of these locations, eSmsConfig uses the latitude, longitude, and time zone of your selection.
Alternatively, you can configure a specific latitude, longitude, and time zone for your location, and provide a name for this custom location.
Based on the location and time zone, x-Messenger calculates the absolute sunrise and sunset time for the current day. The block also takes summer time/winter time into consideration, if it is configured on the computer where eSmsCofig is installed. To do such configuration, you should select check box of
"Automatically adjust clock for daylight for saving changes" in the "Date and Time Properties" dialog.
276
Timing diagram
Description of function
The function calculates the value at the input and sets or resets Q depending on the sunrise time and sunset time at the configured location and time zone of the module.
6.5.46 Stopwatch
Short description
The stopwatch records the time elapsed since it was enabled.
Connection
Input En
Input Lap
Input R
Parameter
Output AQ
Description
En (Enable) is the monitoring input. x-Messenger sets the current elapsed time to 0 and begins counting elapsed time when En transitions from 0 to 1. When En transitions from 1 to 0, the elapsed time is frozen.
A positive edge (0 to 1 transition) at input Lap pauses the stopwatch, and sets output to lap time.
A negative edge (1 to 0 transition) at input Lap resumes the stopwatch, and set the output to current elapsed time..
A signal at input R (Reset) clears the current elapsed time and lap time.
Time base for elapsed time, which you can set to hours, minutes, seconds, or 1/100ths of seconds.
The output AQ outputs value of the current elapsed time when it is a negative edge (1 to 0 transition) at the input Lap, and outputs value of the Lap time when it is a positive edge (0 to 1 transition) at the input Lap.
A positive edge (0 to 1 transition) resets the value at output AQ to 0.
Parameters Time base
You can configure the time base for the analog output:
277
The time base for the elapsed time can be in hours, minutes, seconds, or 1/100ths of seconds (units of 10 milliseconds). The smallest time base, and therefore the resolution, is 10 milliseconds, or 1/100ths of seconds.
Timing diagram
278
Description of the function
When En = 1, the current time increases.
When En = 0, the current time counting pauses.
When En = 1 and Lap = 0, the output AQ outputs the value of the current elapsed time.
When En = 1 and Lap = 1, the current time continue increasing, but the output AQ outputs the value of the
Lap time.
When En = 0 and Lap =1, the output AQ outputs the value of the Lap time.
When En = 0 and Lap = 0, the output AQ outputs the value of the latest current time.
When R = 1, both the current time and the Lap time are reset.
6.5.47 Cam Control
Short description
The cam programmer function Cam Control is used to control a set of 8 built-in cam wheels.
On its 8 outputs (representing the 8 wheels), the function provides the state corresponding to the current position of the shaft wheels.The cam configuration can be set for each position, output state is adjustable.Once the maximum value has been reached, the cam restarts from its initial position (output returns to 0).
Connection
Input Forward
Description
MOVE FORWARD is the input which is used to control cam progress; it moves one step forward at each rising edge (digital status is changed from 0 to 1).
Input Reverse
Input Reset
Output Output1..
............
............
Output8
MOVE BACKWARD is the input which is used to control backward cam movement; it moves one step backward at each rising edge (digital status is changed from 0 to 1).
RESET (initialization): When this input is active, the cam is replaced to its initial position: the POSITION output will be forced to 0.
The status of the 8 outputs is corresponding to the current position of the shaft (representing the 8 wheels).
279
Position
Parameters analog output corresponding to the current cam position (0 to 49).
From the property dialog box, you may adjust:
The number of program steps: Its value is between 1 and 50,
Output status [1..8]: for each position of the shaft.
The following figure shows an example of a part of parameters window:
Notes:
1.The FORWARD input takes priority over the BACKWARD input.
2.If the FORWARD and REVERSE inputs are not connected, they are set to inactive.
When selected, the "Retentivity" enables the current value of the timer to be retrieved following a power failure.
Modification of Parameters from the Front Panel
To modify the parameters from the front panel of the controller, do not tick up the "Protection Active" box of the property dialog box.
From the PARAMETERS menu, it is possible to modify bit-wise the contents of all the cam programmer steps, but it is not possible to modify the number of steps.
After you have selected the block number, then enter:
The step number: Value between [0..49],
Output status [1..8]: For each output one can set the value to INACTIVE or ACTIVE.
6.5.48 Angular Cam Timer
Short description
This function block is used to describe operation of a cam timer based on the angle made by the cams as
280
the analog input. The number of steps can be selected and each step corresponds 2 configurable outputs.
Connection Description
Input
VALIDATION:
Enables the function. If this input is not activated, the function remains inactive.
Activated implicitly if it has not been connected.
Input ANGLE: Timer command input (from 0° to 359°). The outputs vary according to this value and the OUTPUT STATE parameter.
Output OUTPUT 1: Output 1 is related to the value in the OUTPUT 1 column in the OUTPUT STATE table. If the value of the angle in the ANGLE input is higher or the same as a value
N in the ANGLE column in the OUTPUT STATE table and less than the value N+1 in the table, the value of the corresponding OUTPUT 1 column is copied to OUTPUT 1
(1 => output at ON, 0 => output at OFF).
Output OUTPUT 2: Output 2 is related to the value in the OUTPUT 2 column in the OUTPUT STATE table. If the value of the angle in the ANGLE input is higher or the same as a value
N in the ANGLE column in the OUTPUT STATE table and less than the value N+1 in the table, the value of the corresponding OUTPUT 2 column is copied to OUTPUT 2
(1 => output at ON, 0 => output at OFF).
Parameters NUMBER OF DEGREES: Equivalent to the wheel step number (2 to 72 steps of 5° to
180°). \
OUTPUT STATES: Table is listing the output states for each position. These states can be modified by left-clicking in the corresponding boxes.
6.5.49 Pumps Management
Short description
APPLICATION-SPECIFIC FUNCTION: PUMPS MANAGEMENT: (TANK MANAGEMENT WITH CIRCULAR PUMP
CHANGEOVER).
This function is used to set to ON a maximum of four digital outputs which can be activated (OUTPUT 1 ...
OUTPUT 4). This number is equal to the maximum number of digital inputs (from 2 to 4) in the ON state. In addition, the outputs set to ON are selected so that in the event of prolonged operation, each output will have been set to ON the same number of times.
The ON duration of the outputs is set to equal values by applying the following technique:
As the number of ON inputs increases, the outputs changing to ON are those following the order of the PILOT
281
OUTPUT NUMBER: 1 for OUTPUT 1, 2 for OUTPUT 2, 3 for OUTPUT 3 and 4 for OUTPUT 4. For example, if the
"outputs controlled" parameter has the value 4, if PILOT OUTPUT NUMBER has the value 3 and just one input is set to ON, only the OUTPUT 3 output will be set to ON. As soon as two inputs change to ON, the OUTPUT
3 output remains at ON and the OUTPUT 4 output changes to ON. As soon as a third input changes to ON, the
OUTPUT 3 and OUTPUT 4 outputs remain ON and OUTPUT 1 changes to ON.
As soon as the number of outputs decreases, the outputs changing to OFF will be those which have been in the ON state the longest. As soon as one output changes to OFF, PILOT OUTPUT NUMBER takes the value of the output number after the output(s) which has (have) just been set to OFF. To complete the above example, as soon as one input changes to OFF, the OUTPUT 3 output changes to OFF and PILOT OUTPUT NUMBER displays the integer value 4.
The Parameters tab in the property box contains the number of outputs which may change to ON depending on the number of inputs which are set to ON. The values of this parameter are fixed at 2, 3 or 4.
If the value of the parameter is fixed at 2, only the OUTPUT 1 and OUTPUT 2 outputs are used and may therefore change to ON. In this case, if more than two inputs change to ON, the OUTPUT 1 and OUTPUT 2 outputs remain at ON and the OUTPUT 3 and OUTPUT 4 outputs remain fixed at OFF.
If the value of the parameter is fixed at 3, only the OUTPUT 1, OUTPUT 2 and OUTPUT 3 outputs are used and may therefore change to ON. . In this case, if four inputs change to ON, the OUTPUT 2, OUTPUT 2 and OUTPUT
3 outputs remain at ON and OUTPUT 4 remains fixed at OFF.
If the value of the parameter is fixed at 4, only the OUTPUT 1, OUTPUT 2, OUTPUT 3 and OUTPUT 4 outputs are used and may therefore change to ON.
All inputs which are not connected have the value OFF.
When the program is initialized, PILOT OUTPUT NUMBER is fixed at 1.
The Parameters tab contains the default check box which re-initializes PILOT OUTPUT NUMBER to 1 (and defines the first output activated when the first input changes to 1) after a controller power failure.
Example of use:
Filling a tank with a group of four pumps operating in parallel. The operating duration of each pump is the same.
282
The "number of outputs controlled" parameter is fixed at 4.
On initialization, PILOT OUTPUT NUMBER has the value 1. On initialization, if the tank is in the state indicated and if a sensor above the water is in the ON state, when the user program is executed, the INPUT 1 and INPUT
2 inputs are ON, INPUT 3 and INPUT 4 are OFF and OUTPUT 1 and OUTPUT 2 are ON.
Assuming that the tank is full, INPUT 2 changes to OFF and OUTPUT 1 changes to OFF. PILOT OUTPUT
NUMBER indicates the value 2.
Assuming that the tank is empty, INPUT 2 changes back to ON, OUTPUT 3 changes to ON and OUTPUT 2 remains ON.
Assuming that the tank refills, INPUT 2 changes back to OFF, OUTPUT 2 changes to OFF and PILOT OUTPUT
NUMBER indicates the value 3.
Assuming that the tank continues to refill, INPUT 1 changes to OFF, OUTPUT 3 changes to OFF and PILOT
OUTPUT NUMBER indicates the value 4.
6.5.50 Defrost
short Description
The defrost output changes to ON when the input temperature is less than the minimum temperature for a time T (T being the cumulative duration of passages below the minimum temperature). If the temperature
283
rises to higher than the maximum temperature during the defrost cycle, the defrost output reverts to OFF even if it has not finished. This output can be triggered and stopped by means of the corresponding inputs.
Connection
Input
VALIDATION
Input
TEMPERATURE
Input
MANUAL
DEFROST ON
Input
MANUAL
DEFROST OFF
Output
DEFROST
Output :
ALARM
Output
CUMULATIVE
TIME:
Parameters
Description function validation input. The function remains inactive for as long as this input is not activated. VALIDATION is implicitly active if it is not connected.
Air temperature in °C*100 (-32768°C to 32767°C).
Sets the defrost output to ON if the temperature is less than the maximum temperature.
Sets the defrost output to OFF (Priority stop).
The defrost output is at ON when the CUMULATIVE OPERATING TIME has elapsed.
the alarm is optional ; where it is validated parameters, the user has the choice between an absolute alarm, i.e. independent of any change to the preset value, and a relative alarm, which is dependent on the preset value :
Absolute Alarm : the user configures a value. When the value measured exceeds this value, the ALARM output switches to logic state 1.
Relative Alarm : the user configures a difference. When the value measured is outside the range "preset value minus difference/preset value plus difference", the
ALARM output switches to logic state 1. The values of the limits defining the range are recalculated each time the preset value is changed.
Measured duration, in minutes, when the temperature is less than the minimum temperature or duration of the current defrost cycle.
CUMULATIVE OPERATING TIME: Time T, in minutes, at the end of which the function triggers defrosting (1 to 32767).
DEFROST CYCLE: Duration of defrosting in minutes (1 to 32767).
MAXIMUM TEMPERATURE: Temperature in °C above which defrosting is stopped
(10°C ... 20°C).
MINIMUM TEMPERATURE: Temperature in °C below which the time T is measured
(-10°C ... 0°C).
284
6.5.51 Comparison of 2 values
Short Description
The COMPARE function is used to compare two analog values.
285
Connection
Input
ENABLE FUNCTION
Input VALUE 1
Input VALUE 2
Function
Parameters
Description an ENABLE FUNCTION Discrete-type input
Integer-type input
Integer-type input
If the VALUE 1 or VALUE 2 input is not connected, the value is set to 0.
The function provides a discrete-type OUTPUT.
The output is active if the result of the comparison between VALUE 1 and
VALUE 2 is true and if the ENABLE FUNCTION input is active or not connected.
The output does not change state if the ENABLE FUNCTION input changes from
Active to Inactive state.
The comparison operators that can be chosen from the Parameters window are:
Symbol Description
Greater than.
Greater than or equal to.
Equal to.
Different.
Less than or equal to
Less than
6.5.52 Multicompare
Short Description:
This function is used to activate the output corresponding to the value present on the "Value" input.
Connection
Input
VALIDATION
Description
Function validation input. Until this input is activated, the function remains inert. Validation is active implicitly if it has not been connected.
286
Input VALUE
Outputs
Value to be compared.
VALUE N: Output ON if Value = Value N.
VALUE N + 1: Output ON if Value = Value N + 1.
VALUE N + 2: Output ON if Value = Value N + 2.
VALUE N + 3: Output ON if Value = Value N + 3.
VALUE N + 4: Output ON if Value = Value N + 4.
VALUE N + 5: Output ON if Value = Value N + 5.
VALUE N + 6: Output ON if Value = Value N + 6.
VALUE N + 7: Output ON if Value = Value N + 7.
Operation:
The comparison value (Value N) can be configured. It must be between 0 and 32760.
6.5.53 Compare in zone
Short Description
The COMP IN ZONE comparison function is used to compare one value between two set points (the MIN and
MAX values of the zone).
Connection Description
Input ENABLE a discrete ENABLE FUNCTION input; this input is Active if it is not connected.
Input VALUE TO MOVE BACKWARD is the input which is used to control backward cam
COMPARE movement; it moves one step backward at each rising edge (digital status is changed from 0 to 1).
Input MIN VALUE A MIN VALUE input, whose type is Integer
Input MAX VALUE A MAX VALUE input, whose type is Integer
OUTPUT The OUTPUT indicates the result of the comparison when the ENABLE FUNCTION input is active.
The OUTPUT does not change state when the ENABLE FUNCTION input is inactive.
287
Parameters From the Parameters window, you can select the state of the output according to the result of the comparison:
ON in the zone: the output will be active if the input value is between the two setpoints (MIN and MAX),
OFF in the zone: the output will be inactive if the input value is between the two setpoints (MIN and MAX).
If MINI is greater than MAXI, then for:
ON in the zone: the output always remains inactive,
OFF in the zone: the output always remains active.
Comparison Function
The diagram below shows the different states the output can take, depending on the input value to compare and the enable input:
6.5.54 Conversion Word bits
Short Description
When the "En" is high, The DEC/BIN function breaks down an integer (16-bit) type input into 16 bit-type outputs.
Illustration:
288
Inputs/Outputs
This function supports 1 integer type 16-bit input:
This function supports 16 discrete outputs: BIT01 (least significant byte) ... BIT16 (most significant byte).
6.5.55 Conversion bits Word
Short Description
When the "En" is high, the BIN/DEC function produces a 16-bit integer-type output from 16 inputs of the following type: Bit
Inputs/Outputs
This function supports 16 discrete inputs: BIT01 (least significant byte) ... BIT16 (most significant byte).
This function supports one 16-bit integer-type output.
6.5.56 Demultiplexer
This function demultiplexer integers. It is used to route the input value onto one of the 4 OUTPUTS on each rising edge of the VALIDATION input.
289
A VALUE copied to an output does not revert to 0 when a VALUE is written to another ADDRESS.
The BASE ADDRESS parameter allows several blocks to be used at the same time to multiply outputs.
The Parameters tab contains:
BASE ADDRESS: Contains the address of the ADDRESS 1 output.
SAVE ON POWER BREAK: Chooses whether or not the function is reinitialised if the controller power supply is disconnected.
When they are not connected, the ADDRESS and VALUE inputs are set to zero.
Example:
When the BASE ADDRESS parameter contains the value 0 these outputs have addresses 0, 1, 2, 3 respectively, and in this case if the ADDRESS input equals 2 the VALUE will be copied to the third output.
If a second block is being used, 8 outputs can be demultiplexed by putting the value 4 as the BASE ADDRESS in the second block and connecting the VALIDATION and ADDRESS inputs to the same source.
6.5.57 Multiplexing
Short Description
The MUX function carries out two input channel multiplexing on the OUTPUT.
Connection Description
Input
CHANNEL A this is the multiplexer input A, whose type is integer.
Input this is the multiplexer input B, whose type is integer.
290
CHANNEL B
Input
SELECTION
Output this input is used to choose the input channel to apply to the output.
this is the multiplexer output.
This value depends upon the state of the SELECTION input.
If the SELECTION input is: inactive: the OUTPUT corresponds to CHANNEL A, active: the OUTPUT corresponds to CHANNEL B.
Notes: 1. If the SELECTION input is not connected, then it is considered to be inactive.
2.If CHANNELS A or B are not connected, then they are set to 0.
6.5.58 Multiplexer
Short Description
This function multiplexes the WORD inputs. It is used to route the value of one of the inputs selected by the
ADDRESS input to the output. The input is routed to the output on each rising edge of the VALIDATION input.
The BASE ADDRESS parameter allows several blocks to be used at the same time to multiply inputs.
The Parameters tab contains:
BASE ADDRESS: Contains the address of the INPUT 1 input.
SAVE ON POWER BREAK: Chooses whether or not the function is reinitialized if the controller power supply is disconnected.
When they are not connected, the digital input is in the OFF state and the WORD inputs contain 0.
Example:
When the BASE ADDRESS parameter contains the value 0 these inputs have addresses 0, 1, 2, 3 respectively, and in this case if the ADDRESS input equals 2 the VALUE of the third input will be copied to the output.
If a second block is being used, 8 inputs can be demultiplexed by putting the value 4 as the BASE ADDRESS in the second block and connecting the VALIDATION and ADDRESS inputs to the same source.
291
6.5.59 Square Boot
Short Description:
This function is used to calculate the square root of the number present as an input with accuracy to two decimal points.
Connection Description
Input Validation Function validation input. Until this input is activated, the function remains inert.
Validation is active implicitly if it has not been connected.
Input Calculation The value must be between 0 and 32767.
input
Output Calculation this input is used to choose the input channel to apply to the output.
output
Operation:
Example: for X = 20000 => Root of X = 141.42. The value read as an output of the function is 14142.
If used as an input, the number is negative and the result is 0.
Performance:
The calculation is accurate to 0.01 either way.
6.5.60 Sin Cos
Short Description
292
This function is used to calculate the cos and sin of an angle between 0° and 90°.
Connection
Input Angle
Description
Input Validation Function validation input. Until this input is activated, the function remains inert. Validation is active implicitly if it has not been connected.
Represents the angle in degrees. Its value must be between 0 and 900 for an angle between 0° and 90°.
Output Sin
Output Cos
Result of ("Angle" sin) x 10000
Result of ("Angle" cos) x 10000
Performance:
The function calculates the cos and the sin to the nearest 0.0001 by rounding up or down as appropriate.
Sin (63°8) = 0.8973 and Cos (63°8) = 0.4415
6.6 Enter into “Customized mode”
Click File->New->Customized Mode or
You now see the complete user interface of eSmsConfig.exe under customized mode. The programming interface for creating your circuit programs occupies the greater part of the screen. The icons and logical links of the circuit program are arranged on this programming interface.
293
To help you to maintain an overview of large circuit programs, the right side and the bottom of the programming interface contains scroll bars, which you can use for vertical and horizontal scrolling of the circuit program.
1. Menu bar
2. Standard Toolbar
3. Programming Toolbar
4. Reference material (Function block list)
5. Info box (Display memory Info, IO status and analog IO values under simulation/monitoring mode)
6. Status bar (Including current operation, current CPU model and the communication status)
7. Programming Interface
Notes: For the detailed operation, please refer to Chapter 10 and Chapter 11 of this part.
294
6.7 Main Functions
1. Edition function
The main function of eSmsConfig is programming for x-Messenger. By using the Logical
Function Edition window of eSmsConfig, you can create and edit your desired x-Messenger programs using various function blocks of x-Messenger and can also perform file operations such as save, print, program management etc.
2. Simulation operation function
After the program is edited, you can view the program operation result on the computer and conveniently check if the said program meets your control requirements. Here eSmsConfig provides you with a completely new off-line test function, through which you can debug the program without installing the x-Messenger on site. With this function, many inconvenience of the site test can be avoided.
3. Real-time monitoring eSmsConfig has a Real-Time Monitoring window. You can view the process of the control system and the running conditions of all x-Messenger and control remote x-Messenger, by connecting the x-Messenger communication port (RS232,USB, Ethernet optional) to the computer you can view the process of the control system.
4. Document
The program circuit can be saved and printed. The analog values also can be saved in one excel file .
295
6.8 Operation Instructions of Customized Mode
6.8.1 Menu Bar
When eSmsConfig is used to edit x-Messenger programs under customized mode, some basic operations including files management, opening and closing of the Tool Bar and Status Bar access to Help information are completed by using pull-down menu under File, Edit, Tools, SMS, View and Help. The Instruction Function list of eSmsConfig is characterized by its flexibility and variation according to the main selection.
It can be changed according to the current operation for convenience of your specific operations.
6.8.1.1 File
The instruction is mainly used for file management, including creation, opening, saving and printing of files.
Fig. 10.1 File Menu
Instruction Name
New
Open
Close
Close All Documents
Save
Save As
Print Preview
Print Setup
Property
Function
Open a new file
Open an old file
Close the current active Window
Close all the current active Windows
Save a file
Save current file to a new path and a new file
Print a file
Preview the file printing result
Setup printing format
File property(page size &model select)
296
6.8.1.2 Edit
Exit Exit the eSmsConfig
Fig. 10.2 Edit Menu
※ Undo: Undo the previous step operation and support consecutive operations.
※ Redo: Recover the contents undone by the previous step of operation and support consecutive operations.
※ Cut: Cut the contents in the area highlighted with the cursor.
※ Copy: Copy the contents highlighted with the cursor.
※ Paste: Paste the contents cut or copied.
※ Delete: Delete various graphic components.
※ Select All: Select all the contents in the current window editing box and setup the label.
※ Goto Apponited block: Goto the apponited block in the program interface.
※ Property: open the property box of the apponited block
※ Properties (all blocks): Open all the property boxes of the selected blocks.
※ Phonebook: Add/Delete phone number into phonebook Refer to the chapter 6.5.2 .
6.8.1.3 Tools
This instruction is mainly used for reading program from x-Messenger, writing program to x-Messenger, diagnosis the communication situation of x-Messenger, program management and simulation and so on. The pull down menu of Tools is shown as the following:
297
Fig. 10.3 Tools Menu
※ Configuration: Select and open the Com port.
※ Disconnect Line: Cancel the connection of PC and x-Messenger.
※ Transfer: Transfer the following data between PC and x-Messenger.
PC-> PLC: Download the program to x-Messenger
PLC->PC: Upload the program from x-Messenger.
Password set: Set Password protection to x-Messenger
Get PLC Version: Get the current x-Messenger hardware version
Set Clock: Set RTC for x-Messenger
Get Clock: Get RTC from x-Messenger
Get Communication Type: Get current communication type
Set Communication Type: Set communication type for current x-Messenger
Set PLC’s address: Set the current x-Messenger address
Get PLC’s address: Get the address of current x-Messenger
Get PLC’s scan time: Get the scan period of the x-Messenger for current program
Summer time/Winter time: Activate/disable the conversion of the summer/ winter time
Set Extended module: Activate/disable the expansion port of x-Messenger
※ Simulation: simulate the x-Messenger program.
※ Select Hardware: Select the model of x-Messenger for programming.
※ Edit Cover HMI: Customers are allowed to edit the first page of the HMI by this menu.
※ User manger: File management, program can be protected with different priorities.
※ Set monit config: select elements for monitoring or saving with Excel file.
6.8.1.4 SMS
The instruction is mainly used for SMS items. The pull down menu is as the following:
298
Fig. 10.4 SMS Menu
※ General Settings: set PIN code and gsm provider selected
Generally, you are not required to fill out the GSM provider, because the x-Messenger unit can automatically search it. But the GSM servers centre number need manually input and the x-Messenger also can save it.
The SIM card can be protected with a PIN code just like for normal cell phone use. The PIN request is activated and the PIN code is inputted in the required field. This concerns PIN1. Further information can be obtained from the SIM card manual. Likewise the process of unblocking the SIM card after three incorrect inputs of
PIN1 is described in the SIM manual. In order to do this, the SIM card must be removed from the x-Messenger and inserted into a mobile phone. Now the card can be unblocked according to the details of the network providers.
Note: 1.The x-Messenger unit do not check the PIN code you set if the SIM card without PIN code protection.
1.
The x-Messenger unit shall not log-in the GSM network unless the correct PIN code inputted if the PIN request of SIM card is activated
※ Set GPRS Params: set the communication parameters if you want to establish the connection between x-Messenger and the PC via GPRS.
299
6.8.1.5 View
This instruction is to display the status bar, workspace and the Information window and so on. The pull down menu is shown as the following:
Fig. 10.5 View Menu
※ Status bar: state bar displaying instruction
※ Workspace: workspace displaying instruction
※ Info Window: Info window displaying instruction
※ Zoom: window proportion displaying instruction. There are four different sizes of the windows for the user to select.
6.8.1.6 Help
300
※ Content Index: Help index and detailed contents
※ About eSmsConfig
6.8.2 Toolbar
The icons of the standard toolbar provide quick access to commands that are also available on the menu.
Standard
Toolbar
New Zoom In
Open
Save
Save All
Cut
Zoom Out
Align Left
Align Right
Align Top
Copy
Paste
Undo
Redo
On-line monitor
Get RTC from x-Messenger
Align Bottom
Page Layout Tab
Open COM port
Download(PC-> x-Messenger)
Upload(x-Messenger-> PC)
Set RTC to x-Messenger
301
6.8.3 Programming Toolbar
The programming toolbar contains integral icons for creating, editing and testing programs. Each one of these tools represents a programming mode, in which mouse operations have different effects.
The editing tools are not available as menu commands.
Catalog of the elements of a circuit program open / close
Selection Tool
Text Tool
Cut/Join
Connector Tool
Constants and Terminals
Basic functions
Special functions
Simulation
On-line test
Selection Tool
You can use the selection tool to select and move blocks, text and connecting lines. You can select objects individually with a left-click; you can select multiple objects with [Ctrl]+Click, or you can use the mouse as a "lasso" to surround objects with a rectangle and capture them as a selection.
You can call the selection tool in any other tool by pressing the [ESC] key or by clicking on the icon in the programming toolbar.
Text Tool
302
This tool is used to insert or edit user-defined text objects in the programming interface. You can specify the font type, font size and font color for each individual label.
Text figures can be set in Wrap Text format. You can adjust the size of a text figure typically by dragging the rectangle handles.
Cut/Join
This tool is used to cut and join connections between blocks. To cut a connection, left-click to select the relevant line while the Cut/Join tool is active. The connection is replaced at the blocks by a reference to the partner block. The reference is labeled with the page number, block number and the I/O of the partner block.
6.8.4 Simulation Tool and status window
A toolbox pops up when you open the simulation mode. It contains:
Icons (e.g. switches) for operator control of the inputs .
An icon for the simulation of a power failure, for testing the switching response with reference to retentivity characteristics after power failure.
Icons (e.g. bulbs) for monitoring outputs .
Simulation control icons and
Time control icons.
Simulation control icons
Start simulation
Stop simulation
Hold simulation (pause)
303
Time control
If you have programmed a time-sensitive circuit, you should use the time control to monitor the reaction of your circuit program.
Start simulation for a specific time or number of cycles.
Set the period and the number of cycles using the following icons.
Setting the period and the time base for a time limited simulation or setting a specific number of cycles
Display of the current time in eSmsConfig
Modification of the current time in eSmsConfig
Status display
Layout of inputs
The inputs are displayed in the form of key or switch icons. The name of the input is displayed below the icon.
An open input represents an inactive switch. When you click on the icon, it is indicated active and the switch is shown in closed state.
Icon for pushbutton I1, not actuated open input
Icon for pushbutton I1, actuated closed input
304
Icon for pushbutton I2, not actuated open input
Icon for pushbutton I2, actuated closed input
Layout of the outputs
The status of an output is indicated by a light or dark bulb icon. The name of the output in your circuit program is displayed below this icon.
Status display of output Q1 Output switched off
Status display of output Q1 Output switched on
The output status only indicates the status as such. Here, you cannot switch an output by clicking on an icon.
When your circuit program switches an output, the indicator lamp is active; when the output is switched off, the indicator lamp is also switched off.
Prerequisite: The display of signal states and process variables is enabled under Tools Simulation.
The colored indication lets you identify the "1" or "0" status of a connecting line. Default color of connecting lines carrying a "1" signal is red. Default color of connecting lines carrying a "0" signal is blue.
305
6.9 Basic Operation
This chapter will tell you how to write logic function graph Program with eSmsConfig, how to simulate the
Program you write with eSmsConfig, how to communicate between PC and x-Messenger with eSmsConfig, how to copy system document of x-Messenger with eSmsConfig, and how to complete the update of application and system Program code. If you want to write a function graph Program, first of all, it’s necessary to start an empty document, and then put the function block into editing box. First set the property of every function block, then link every function block according to logic controlling relation, thereby complete the protracting of a logic function graph. In addition, in order to help the users confirm if the function graph accord with the prospective controlling result, eSmsConfig also provides most intuitionist function of simulation. You can get the moving result of the program through simulation of the function graph.
6.9.1 Open File
6.9.1.1 Open New File
Operation method:
To open a new file, click ‘New-> Customized mode’ option of menu ‘File’, click once with left button of mouse, or click once in toolbar. As shown in the following fig.
Fig.7. 9.1 Open New Document
Notes: An option Window of outside-meet extended module will appear before a new document opened.
306
Fig.7. 9.2 Hardware type selection
Page layout set and hardware selection before programming
In the Page Layout tab, you can specify how and on how many pages to print your circuit program. You can preview the pagination in this tab. If you choose more than one program page, the page breaks are indicated by white lines on the programming interface.
The hardware type selection is also needed be done before programming. The available elements are showing in the right area in the above figure.
6.9.1.2 Open Existed Document
Operation Method:
1. To open a document, click ‘Open’ option of menu ‘File’ once with left button of mouse ,or click in toolbar, shortcut key ‘Ctrl+O’ also can be used. As shown in Fig 11.3: once
Fig7. 9.3 Open Existed Document
307
2. Click ‘Open’, find the path of saving file, dialogue box as follows:
Fig7.9.4 Dialogue Box of Existed Document
3. Click the file you want to open with left button of mouse, then click button “Open”. After opening the document, you can modify or print the document.
6.9.2 Edit Function Diagram Program
6.9.2.1 Place Function Block
While you set up a new document, you can write your control Program in the new program interface.
The method and process of placement is as follows:
The method of placing function block is as follows: choose function block needed from the workspace left of the program interface.
Operation Procedure:
1. Choose corresponding function group. “Constant”, “Basic”, ”Special” list and various blocks can be selected .Refer to the function block instruction chapter 6 for detail instruction of function blocks
2. Click the block you needed with left button of the mouse
3. Move the mouse to the proper place in the program interface, click with left button of the mouse, then complete the placement of a block.
4. According to above operation, put all modules in program interface.
E.g.: To complete all the function block of one certain system control, as Fig 7.10.1 shown, put all function modules into the edit program interface.
308
Fig 7.10.1 Place block
6.9.2.2 Edit Property of Function Block
After put all function block in edit box, it’s necessary to setup property of every function block. This is the most important step to write function block Program.
Operation Method:
1. In the function block Program interface, click some block twice with left button of the mouse, or pitch on a block and press right button of the mouse, then an edit menu appears, and then click
“Properties…” of this menu. As shown in Fig 11.6:
Fig 7.10.2 Block edit menu
2. Property dialogue box, as shown in Fig 7.10.3, to setup each item of content according to what you need, you also could click “Help” to observe the detail instruction.
309
Fig 7.10.3 property box
Note: Different block has different property setup, especially the property of special function module. Please read chapter 6, the explanation to refer the detailed setup.
6.9.2.3 Setup link
After put all the blocks needed in protracting function graph, and set up properties as needed, it’s necessary to set up link according to logic control relation and make it an integrated function diagram.
Operation Method:
1. Pitch on shortcut key , when the mouse becomes the shape of a pen, it can be used to link.
2. To do so, move the mouse pointer to a block input or output and press the left mouse button. Keep the mouse button being pressed down and then drag the mouse pointer from your selected source terminal to the target terminal. Now release the mouse button to anchor the connecting line to both terminals. While the connecting line is being drawn, it is shown as a straight line between the first terminal and the mouse pointer.
Once it is anchored, it appears as a combination of horizontal and vertical lines, which can be manipulated using the selection tool.
310
Fig. 7.10.4
eSmsConfig offers you a further option of connecting blocks when you right-click on the input or output of a block. In the shortcut menu, click the Connect with block menu command. This calls a selection list that contains all blocks available for your connection. Click on the relevant target block. eSmsConfig Comfort then draws the connecting line. This method is especially useful for connecting a source to a target block over a greater distance on the programming interface.
Fig. 7.10.5
Tips on connecting blocks
1. Move the mouse pointer over a block and briefly hold it in this position. The name of the block is shown.
The name of the block input appears when you move the mouse pointer onto the input.
2. To make it easier for you to interconnect blocks, a blue frame around the mouse pointer pops when it is
"captured" by a pin.
311
Rules for connecting blocks
The following rules apply to the connection of blocks:
1. You can connect a single input to multiple outputs.
2. You cannot connect multiple inputs to a single output.
You cannot interconnect I/O in the same path of a circuit program. Recursion is not permitted. Interconnect a flag or output if necessary.
Special function blocks also have green "connectors". These do not represent connecting pins, but are used instead for assigning the parameter settings.
Analog I/O cannot be connected to digital I/O.
6.9.2.4 Delete Function Block or Delete Link
When you put some needless block in program interface or link some default ones, you need to delete them as follows:
1. Pitch on module or link to delete with mouse.
2. Press “Delete” in the keyboard, or click right button of the mouse, select option
“Delete” in the menu, then you can delete the module or link.
6.10 Simulation Running
eSmsConfig.exe could edit function diagram, and perform function of simulation operation.
After you finish the edit, you can start the function of simulation operation, to examine program to see if it performs your control logic or not.
Operation Method:
1.Click “Simulation” under the menu “Tools” with left button of the mouse . It’s time to start program of simulation, or click “ ” in the simulation toolbar with mouse, and it also can open simulation operation interface. It shows as Fig. 11.9.
312
Fig. 7.10.6
Start simulation
2. Click input block with mouse. It can change the state of input, state displays “ON” and “OFF” in the output point of the module, so you can observe the state of input or output.
3. Click button again, to terminate the operation function of the module.
Fig. 7.10.7 Simulation Operation
313
Attn: In above graph, you can see “ON” or “OFF” state of input and output, and the output state and the current state of timing and counting of all blocks. Through this simulation operation graph, you can exam the program to see if it performs control requirement or not.
6.11 Save and Print
Operation method of file saving
1.To save a Program, click option “save” or “Save As” under menu “File” with left button of the mouse, as shown in Fig.7.10.8, or click button “ ”under toolbar.
2. You can set up saving path and file name in this box.
3. After the setup of the file saving path and file name, click “save” to save file in the appointed path, then complete to save file.
Fig. 7.10.8 Save File Menu
Operation Method of Printing File
1. Click option “Print” under menu “File” with left button of mouse.
2. Dialog box as shown in Fig. 7.10.9 appears, set up your printing requirement according to the cue of dialog box.
3. Click “confirm” with left button of mouse, then your file will be printed in your printer.
314
Fig. 7.10.9 File Print
6.12 Modify Password and transfer the Program
Operation Method: a. First of all, link x-Messenger with your PC through the optional way: RS232 cable, USB cable (need install driver first), Ethernet connection.
b. Open application software eSmsConfig, set up a new document, then open computer com. Click option
“Configuration” under menu “Tools” with left button of the mouse, or click“ ”in toolbar, dialog box shown as 7.10.10 appears, then select your communication port and speed.
Option A. RS232. This option is used when you use the ELC-RS232 or ELC-USB(relative driver needed) cable.
Option B. Ethernet. This option is used when you use the EXM-E-Ethernet module.
Option C. GPRS. This option is used when you has established the GPRS connection between x-Messenger and PC.
Option D. USB. This option is used when you use the EXM-USB-B cable.(relative driver needed)
Fig. 7.10.10 Set Up Port and Baud Rate
315
1. Setup Password and Time
I. x-Messenger permits you to set up password for your Program. Only after input of right password, you can write, read and modify your Program.
Operation method of setup password a. Click “Tools->transfer-> Password set” with left button of mouse, dialog box shown as Fig.7.10.11
appears:
Fig. 7.10.11 Modify password
You can modify communication password of your x-Messenger mainframe in this dialog box.
b. Input new password in edit box after “New Password”, “write to x-Messenger.
II. You can set up time for x-Messenger
Operation Method: c. Clink option “Tools->transfer->Set EXM time” with left button of the mouse, or clink “ ” under toolbar, dialog box appears shown as Fig. 7.10.12.
d. Display system time in this dialog box, click “ of x-Messenger succeed.
Fig. 7.10.12 Modify Time Interface
“, cue shown as Fig. 7.10.13 appears, to renew time
Fig. 7.10.13 Setup Time Succeed
2. Download/Upload Function Block Program
After you debug the function graph successfully, you need to download it into x-Messenger, and operate as
316
following process.
Operation Method of read-in Program a. First of all, link x-Messenger with your PC through the optional way: RS232 cable, USB cable(need install driver first), Ethernet connection.
b. Open application software eSmsConfig, set up a new document, then open computer com. Click option
“Configuration” under menu “Tools” with left button of the mouse, or click“ ”in toolbar.
c. Click option “transfer->PC->x-Messenger” under menu “Tools”; or click button “ ”in toolbar d. Click button “ ” with left button of mouse, start update Program, downloading status shown as Fig.
7.10.14 display update Program course.
Fig. 7.10.14 downloading status
Attn: After the Program update, x-Messenger will run the Program automatically, need not restart.
Operation Method of Upload Program: a.
Click option “Transfer->x-Messenger->PC” under menu “Tools” with left button of mouse, or click
“ ”under toolbar.
b.
Click button “ ” with left button of mouse, start upload Program, uploading status shown as Fig.
7.10.14 display upload Program course.
6.13 How to prevent your program from being copied/stolen?
For OEM users, they have extremely high requirement on program protection, so our “program password” might not be able to 100% cater for their high demand in this aspect.
In order to absolutely prevent user’s intellectual works(program in the CPU) from being copied/stolen by unexpected personnel, user might make good use of “Disable read program” feature, and upon such feature being activated, no one including user himself/herself can read program from CPU ,in other words, “program upload” would be permanently prohibited, surely, under such situation, copy machine(ELC-COPIER) can not work either. However, new program can still be allowed to be downloaded into such CPU. Therefore, please take good care of your program, and save it in a safe place as backup to avoid unnecessary trouble resulted from your program losing.
317
The listed below is just detailed procedures on how to make such configuration:
1. While a new program being made or a ready program being opened,open the property dialog box of program via the menu File->Properties, or click the icon , and switch over to Parameter tab.
318
2. Click download icon to download program to CPU,in this case, the program in the CPU shall be protected completely, in other words, such protected program can not be uploaded by anyone in any way anymore.
Note:Merely CPU with firmware version no less than V35 can support such function. Moreover, such “disable read program” feature would NOT work, while the CPU’s firmware version is less than v35, or the old version(before v2.3.0.0) eSmsConfig is being used.
6.14 On-line monitoring/test circuit program
After you are satisfied with your program simulation and have downloaded it to x-Messenger CPU, you can also perform an online test of the circuit program. An online test is similar to simulation in that you can view inputs and outputs and block parameters. It differs, however, in that you are testing the program running in
319
the x-Messenger with "live" inputs rather than testing the program on the PC with simulated inputs.
Multiple registers can be accessed individually by clicking “Tools->Set Monitor Config”.
Monitor mode:
Under monitor mode, user can change the spare output (the input pin of Q is not connected to other blocks) state via eSmsConfig.
320
Right click "Q2" and then click "Set Output State".
Click "OK" button and the Q2 of x-Messenger will be turned off.
321
How to transfer monitoring data (AI/AQ) to an Excel file ?
Example program:
1. Select Tools-> Set Monit Config and further click it.
322
As below configuration shows, all history data of AI/AQ under monitor mode can be automatically saved to one EXCEL file for user’s reference.
Caution: If the “clear previous data” is selected as well, then the history data cannot be saved, and then only the current monitor data can be saved, furthermore, the history data (previous monitor data) would be simultaneously cleared.
2. Click here to enter Monitor Mode
3. View the data by clicking View-> Monit data.
323
4. Click corresponding time.).
to transfer data into one excel file (it contains AI1/AQ number, value and the
324
Chapter 7 Description of the WIFI module built-in the EXM WIFI CPU
There is a WIFI module named “HF-A11” built-in the EXM WIFI CPU, before establishing the communication between EXM WIFI CPU and other devices(including PC EXM WIFI CPU or the device can be connected to the Ethernet network), you need do some configurations via the web sever built-in the HF-A11 module.
Bulit-in Wireless Parameters
Support 802.11b/g/n wireless standards
Support TCP/IP/UDP network protocols
Support work as STA/AP mode
Support Router/Bridge mode networking
Support Transparent/Agreement Transmission Mode(Transparent used by EXM WIFI CPU)
Support Friendly Web Configuration Page
Support Palmodic Signal, WIFI connection instruction
Outdoor 100m with 3dBi antenna and indoor 40m;
FCC /CE Certificated
Indicator instruction.
is built-in
325
These two indicators is for the wifi module, not for the LAN port.
1.Indicator the WIFI module status of power on process:
“1”-Finish WIFI module boot up process;
“0”-WIFI module boot up not finish.
2.WIFI status indicator: “1”- WIFI connection available.
“0”-No WIFI connection
7.1 Functional description
Wireless Networking
HF-A11 module can be configured as both wireless STA and AP base on network type. Logically there are two interfaces in HF-A11. One is for STA, and another is for AP. When HF-A11 works as AP, other STA equipments are able to connect to wireless LAN via HF-A11 module. Wireless
Networking with HF-A11 is very flexible.
Following figure shows the functional architecture of HF-A11 module:
Figure 15. Connection inside of EXM WIFI CPU between HF-A11 module and CPU board
Notes:
AP: that is the wireless Access Point, the founder of a wireless network and the center of the network nodes. The wireless router we use at home or in office may be an AP.
STA: short for Station, each terminal connects to a wireless network (such as laptops, PDA and other networking devices) can be called with a STA device.
326
Basic Wireless Network Based On AP (Infrastructure)
Infrastructure: it’s also called basic network.It built by AP and many STAs which join in.
The characters of network of this type are that AP is the center, and all communication between
STAs is transmitted through the AP. The figure following shows such type of networking.
External Antenna
If user select external antenna, HF-A11 modules must be connected to the 2.4G antenna according to IEEE 802.11b/g/n standards.
The antenna parameters required as follows:
Transparent Transmission Mode
327
HF-A11 modules support serial interface transparent transmission mode. The benefit of this mode is achieves a plug and play serial data port, and reduces user complexity furthest. In this mode, user should only configure the necessary parameters. After power on, module can automatically connect to the default wireless network and server.
As in this mode, the module's serial port always work in the transparent transmission mode, so users only need to think of it as a virtual serial cable, and send and receive data as using a simple serial.
The transparent transmission mode can fully compatible with user’s original software platform and reduce the software development effort for integrate wireless data transmission.
Notes:
1.The WIFI module HF-A11 module is using the COM3 port of the EXM WIFI unit
2.The communication parameters is fixed. Baud rates:9600; Data bits:8 Parity:None Stop:1;
3.The data transmission protocol for COM3 is the MODBUS TCP
Basic Wireless Network Based On AP (Infrastructure)
Infrastructure: it’s also called basic network.It built by AP and many STAs which join in.
The characters of network of this type are that AP is the center, and all communication between
STAs is transmitted through the AP. The figure following shows such type of networking.
328
Wireless Network Based On Adhoc Network (Adhoc)
Adhoc: It’s also called independent basic service set, and it’s built by two or more STAs without
AP, this type of network is a loose structure, all the STAs in the network can communicate directly.
As showing in the figure below, HF-A11 (1) can be treat as an AP, and HF-A11 (2), HF-A11 (3) and the laptop are STAs connected to HF-A11 (1). Meanwhile, all HF-A11 modules can connected to EXM WIFI CPU via UART interface. All HF-A11 modules can be operated and managed through the laptop. So it is convenient to O&M all EXM WIFI CPUs. Moreover, in such
Adhoc network structure, the whole coverage of a wireless network can be extended easily.
329
Security
HF-A11 module supports multiple wireless encryption mechanisms, and enables to protect the security of user’s data transmission, the mechanisms include:
WEP
WAP-PSK/TKIP
WAP-PSK/AES
WAP2-PSK/TKIP
WPA2-PSK/AES
330
Address Binding
HF-A11 module supports the feature of binding the BSSID address of target network.
According to the provisions of 802.11 protocol, different wireless networks can have a same network name (ie SSID / ESSID), but must correspond to a unique BSSID address (ie MAC address). Illegal intruders can create a wireless network with the same SSID / ESSID, it will make
STAs in the network to join to the illegal AP, thereby and then network leakage happen.
Users can prevent STA from joining to illegal network by binding the BSSID address,to improve wireless network security.
7.2 OPERATION GUIDELINE
Configuration via Web Accessing
When first use HF-A11 modules(EXM WIFI CPUs), user may need some configuration. User can connect to HF-A11x module’s wireless interface with following default setting information and configure the module through laptop or smart phone.
Table 5
HF-A11 Web Access Default Setting
Open Web Management Interface
Step 1: Connect laptop to SSID “HF-A11_AP” of HF-A11 module via wireless LAN card;
Step 2: After wireless connection OK. Open Wen browser and access “http://10.10.100.254”;
Step 3: Then input user name and password in the page as following and click “OK” button.
331
Figure 22. Open Web Management page
The HF-A11 web management page support English and Chinese language. User can select language environment at the top right corner and click “Apply” button.
The main menu include five pages: “Mode Selection”,” AP Interface Setting”,”STA Interface
Setting”,”Application Setting”, and “Device Management”
Notes:
Default, High-Flying suggests all Web management related operation shall execute at AP mode.
(Even you need configure STA parameters and want module works as STA mode). If user selects
STA mode and still want to configurate the module through Web browser, you have to access the module through another AP (and get the module IP address through this AP.)
Mode Selection Page
332
This page use to setting the module working mode (Transparent Transmission or Agreement
Transmission) and wireless networking mode (AP and STA mode).
AP Interface Setting Page
This page use to setting the parameters when HF-A11 module works as AP.
333
Figure 24. AP Interface Setting Page
STA Interface Setting Page
This page use to setting the parameters when HF-A11 module works as STA.
Such as SSID of AP which module need to connected, and also select the networking type:
DHCP or static IP address.
334
Application Setting Page
This page use to setting the parameters of serial port communication, such as UART setting and high layer network protocol setting which used support serial communication.
335
Notes:
1.Generally, Network protocols support three modes: TCP Server, TCP Client, and UDP. UDP has no server and client requirement according to standard.
Besides module working as TCP Server (IP address not required in this mode). User must set the
IP address of the device which need communicate with HF-A11 module.
Also the Port ID between two sides of the communication devices must keep the same.
2.If you have load factory default, the Baud rates shall be “57600”(This is the module factory default settings), but the EXM WIFI Unit only support the “9600” , so you must keep the UART settings as follows, other settings will be not available for EXM WIFI unit to communicate.
336
Establish the communication between eSmsConfig and EXM WIFI Unit.
337
Two communication modes available:
A. EXM WIFI unit works as server, eSmsConfig works as client.
338
B. EXM WIFI unit works as client, eSmsConfig works as server.
eSmsConfig com settings
339
Web page settings of wifi module
Device Management Page
This page use to manage HF-A11 module general setting, such as administrator setting, restart module button, restore factory default setting button, and update firmware through webpage.
Notes:
If you click the “Load Default” button, you must change the baud rates to 9600, otherwise the the
HF-A11 module cannot establish communication with EXM WIFI CPU.
7.3 10/100M Ethernet Interface
HF-A11 modules provide one 10/100M Ethernet PHY layer interface for data transmission or user configuration.
Close module’s Ethernet port function can reduce the power consumption. The default setting for
HF-A11 is close Ethernet port function, but you can open the Ethernet port in the configuration of
340
eSmsConfig.exe
If you recovery the settings of the HF-A11 module, the Ethernet port would be closed, if you still want to use the LAN port, you must open it in the eSmsConfig.exe from the menu:Tools->wifi parameters
7.4 HF-A11 Ethernet Interface Networking (As AP)
HF-A11 Ethernet Interface Networking (As AP)
For above networking, HF-A11 module works as AP and also the center of this network. All devices’s IP address in this network shall use the same network segment with HF-A11 and they can intercommunication with this method.
341
Notes:
1.After the Ethernet port opened, you can directly connect the PC to the LAN port of CPU by net wire, and set the internet card with the dynamic IP address, and then you can configure the wifi module with the built-in web page, you only need input the gateway of your PC into the browser, and then the web page will be showing:
2. Indicators on the LAN port is not for the LAN connection, it is for the wifi modu
Indicator instruction.
These two indicators is for the wifi module, not for the LAN port.
2.Indicator the WIFI module status of power on process:
“1”-Finish WIFI module boot up process;
“0”-WIFI module boot up not finish.
2.WIFI status indicator: “1”- WIFI connection available.
“0”-No WIFI connection
342
7.5 How to Configure the wifi module by the eSmsConfig.exe
If the WIFI module is worked on the STA mode, but it is disconnected with any router and the LAN port is also closed, so, the web configuration would be disabled, now you need configure the WIFI module via the program port by eSmsConfig.exe.
Hardware requirement:
Program cable :ELC-RS232 cable, ELC-USB cable.
Steps:
1. Connect the programming cables to the program port
2. Open the eSmsconfig.exe and establish the communication with WIFI CPU.
Note:
1.
Only the RS232 option available for the wifi parameters setting.
3. Click the menu “Tools-> wifi
343
params”
4.Click the “Connect” button, and wait about 30 seconds.
5.Read kinds of parameters as follows and click write button to set into the wifi module.
344
Manage item:
This page use to setting the module working mode (Transparent Transmission or Agreement
Transmission) and wireless networking mode (AP and STA mode).
Please select “Through”, “Agreement” is not available for WIFI CPU.
345
This is the name and password for the web configuration.
Reset button, click it, the wifi module in the CPU will be reset once.
Recover button, click it the wifi module will be recovery, and the baud rates will be set from 57600 to 9600 by eSmsConfig.exe automatically.
Note:
1. We need set baurates in the wifi module 9600, and then the communication between the wifi module and the EXM CPU will be established, but by the default setting with the HF-A11 factory is57600.
2.After you click the “Recovery” button, please wait about 20s, and then connect the wifi module by clicking the “Connect” button again or exit the settings dialog box, otherwise the baud rates of the wifi module will stay with “57600”, so when you want to connect to the wifi module, you must select “57600”.
Read the configuration from the wifi module by clicking “Read” button. Such operation only can get the information on the current page.
Write the configuration into the wifi module. Such operation only can set the configuration in to wifi module on the current page.
Comm item:
346
Set the serial parameters for the communication between wifi module and the EXM CPU.
Please select “9600”, other settings would be unavailable.
Please keep the default settings, do not change.
Disable “Auto frame”.
Network settings:
Mode : Server/client
Protocol: TCP
Port number : when mode is server, such port is for local host, when mode is client, such port is for remote host.
Server Ip address: When mode is client, the remote host IP address need set in here.
347
The default settings of HF-A11 is closed, if you want to use the LAN port, please select open.
AP setting item
STA item
348
Wireless
Name: the name of the destination router
MAC: MAC address of the the destination router
Password settings
WAN
IP address settings.
Two communication modes available:
B. EXM WIFI unit works as server, eSmsConfig works as client.
349
WIFI parameter settings communication parameters in eSmsConfig
Note: The modbus type must be MODBUS TCP.
B. EXM WIFI unit works as client, eSmsConfig works as server.
350
WIFI parameter settings communication parameters in eSmsConfig
After the connection is established between EXM WIFI CPU, and then you can download/upload program, monitoring the registers by eSmsConfg.exe,
351
7.6 How to configure WIFI connection (TCP protocol) among EXM WIFI CPUs?
352
Step1: we must establish the TCP connection among the EXM WIFI CPUs, take an example as above figure shows, The wifi module are all working on STA mode.
The master EXM cpu works as a server, and slave1 and slave2 are working as client.
Regarding the settings of the WIFI parameters, you can the pre-chapter for detail.
Because of the default address of EXM CPU is 1, you need also to change the Slave 2 address to 2 by panel key or the menu via Tools-> transfer-> Set EXM address.
Change the address by panel key.
Press ,and then press
Press with UP or DOWN button and confirm with OK.
Press
Press
Change address
353
Step2: Program in the eSmsConfig.exe.
Example
Regarding the program. We need realize the below logic.
1.I1--I4 in master to control the Q1--Q4 in slave1&salve2, if I1 is ON in master, the corresponding Q1 in salves is ON; I2 is ON in master, the corresponding Q2 in salves is ON;....I4 is On in master, the corresponding
Q4 in salves is ON. If I1 is OFF in master, the corresponding Q1 in salves is OFF.......I4 is OFF in master, the corresponding Q4 in salves is OFF.
2. Read the Inputs I1--I4 status of slave 1 to control the F11--F13 in master; Read the Inputs I1--I4 status of slave 2 to control the F21--F23.
3. Read the AF1 value of slave1 to be saved in the AF1 of master; Read AF1 value of slave2 to be saved in AF2 of master.
354
Program in slave 1
(Note: In the program, you can put the input/output block in, but you cannot link the input pin of the output)
Program in slave 2
(Note: In the program, you can put the input/output block in, but you cannot link the input pin of the output)
355
B001: Transfer the I1--I4 status from the master to the Q1-Q4 of the slave1. Setting as follows:
356
B002: Transfer the I1--IA status from the master to the Q1-QA of the slave2. Setting as follows:
357
B005: Read the I1--I4 status from the slave1 to the F11-F13 of the master. Setting as follows:
358
B006: Read the I1--I4 status from the slave2 to the F21-F23 of the master. Setting as follows:
359
B009: Read the AF1 value from the slave1 to the AF1 of the master. Setting as follows:
360
B010: Read the AF1 value from the slave2 to the AF2 of the master. Setting as follows:
361
362
Appendix
A Technical data
CPU Model
Power supply:
Nominal voltage
Operating limits
Immunity from micro power cuts
The main frequency range
Max. absorbed power
Isolation voltage
Protection against polarity inversions
Input parameters:
Input No
Digital input
Analogue input
Input voltage
Input signal0
Input signal1
Input Response Time
Maximum counting frequency
Sensor type
Isolation between power supply and inputs
Isolation between inputs
Protection against polarity inversions
Input voltage 1
Input signal0
Output parameters:
Output No.
Output type
Continuous current
Max. breaking voltage
Max. Allowable Power Force
Electrical durability Expectancy
Mechanical life
363
EXM-8AC-R
AC 110-240V
AC 85-265V
Typ.5 ms
47-63Hz
86mA (85V ac) ; 35mA (265V ac)
1780V AC
Yes
6 ( I1-I6 )
6 ( I1-I6 )
None
AC110-240V
AC0-40V;<0.03mA
AC79-240V; >0.06mA
Delay time at 0 to 1:
120V AC :Typ. 50 ms
240V AC :Typ. 30 ms
Delay time at 1 to 0:
120V AC :Typ. 90 ms
240V AC :Typ.100 ms
Typ. 4Hz
Contact or 3-wire PNP
None
None
Yes
AC110-240V
AC0-40V;<0.03mA
2 (Q1-Q2)
2Relay output
Resistive load 10A/Inductive load 2A
AC 250 V DC 30 V
(Q1-Q2)1250VA 300W
105 Operations at Rated Resistive Load
107 Operations at No Load condition
Response time
Built-in protections
Galvanic isolation
Switch frequency:
Mechanism
Resistor/light load
Sensitive load
GSM parameter
Type of mobile wireless service
Operating frequency for GPRS transmission / with downlink / maximum for GPRS transmission / with uplink / maximum
Other parameters:
Ethernet interface
Voice alarming
Weight
Function blocks
RTC accuracy :
RTC Backup at 25 °C
Program and settings Backup
Data Power-off retentivity
Short-circuit protection
Cycle time
Connection cables
Ambient temperature
Storage temperature
Certification
Mounting
Dimensions
Programming cable
Third party device(HMI) <=> xLogic
Extensions
RS485
LCD
Operate Time : 15 mSec. Max.
Release Time : 10 mSec. Max.
Against overloads and short-circuits: No
Against overvoltages (*): No
None
10Hz
2Hz
0.5Hz
SMS, GPRS
850MHz,900MHz,1800MHz,1900MHz,
80 kbit/s
40 kbit/s
No
No
Approx.500g
512 blocks
MAX ±2S/day
20 days
10 Years
Yes
External fuse required typ. 0.6ms ➞ 8.0ms
2 x 1.5 mm² or 1 x 2.5 mm²
-20 to + 55 ºC
–40 ºC to + 70 ºC
CE
On 35 mm standard mounting rail, 4 MW, or wall-mounting
W x H x D (95*90*67 mm)
PC cable, (RS232 or USB)
Yes (work as modbus master or slave)
Yes(8 PCS EXM-E expansion)
Yes,( PRO-RS485 cable or EXM-E-RS485 module is required)
Yes(4*16 characters)
364
CPU model
Power supply:
Nominal voltage
Operating limits
EXM-12DC-DA-R
DC 12-24V
DC 10.8-28.8V
EXM-12DC-DA-R-N
Immunity from micro power cuts
Max. Startup current
Typ.5 ms
Max. 0.5A
Max. absorbed power Normal: 3.3 W (10.8V dc) ; 3.7 W (28.8V dc)
Transient Current: 1A (DC12V)
Protection against polarity inversions Yes
Input parameters:
Input No
Digital input
Analogue input
Digital inputs( I5-I8 ):
Input voltage
Input signal0
Input signal1
Input current
Response time
Maximum counting frequency
Sensor type
Input type
Isolation between power supply and inputs
Isolation between inputs
8 ( I1-I8 )
8 ( I1-I8 )
4 ( I1-I4)(0..10V DC)
DC0-28.8V
< 5V DC; <1mA
> 8 V DC;>1.7mA
2.3mA @ 10.8V dc
2.6mA @ 12.0 V dc
5.2 mA @ 24 V dc
6.3 mA @ 28.8 V dc
0 to 1 :<1 ms ;1 to 0 :<1 ms
60k Hz(I7--I8)
Contact or 3-wire PNP
Resistive
None
None
Inputs used as digital inputs( I1-I4 ):
Input voltage DC0-28.8V
Input signal0
Input signal1
Input current
< 5V DC;<0.1mA
> 8 V DC;>0.3mA
0.4mA @ 10.8V dc
0.5mA @ 12.0 V dc
1.2mA @ 24 V dc
1.5mA @ 28.8 V dc
Response time 0 to 1 :Typ. 1.5 ms ;1 to 0 :Typ. 1.5 ms
Typ.:4 HZ Maximum counting frequency
Sensor type
Input type
Contact or 3-wire PNP
Resistive
365
Isolation between power supply and inputs
Accuracy at 55 °C
Isolation between analog channel and power supply
Cable length
None
Isolation between inputs None
Inputs used as analog inputs( I1-I4 ):
Measurement range
Input impedance
DC 0---10V
Min, 24KΩ ; Max. 72KΩ
Input voltage
Resolution
Accuracy at 25 °C
28.8 V DC max
10bit ,0.01V
± (Max.0.02)V
± (Max.0.04)V
None
10 m max. shielded and twisted
Output parameters:
Output No.
Output type
Continuous current
Max. breaking voltage
Max. Allowable Power Force
Electrical durability Expectancy
Mechanical life
Response time
Built-in protections
4 (Q1-Q4)
4 Relay output
Resistive load 10A/Inductive load 2A
AC 250 V DC 30 V
1250VA 300W
105 Operations at Rated Resistive Load
107 Operations at No Load condition
Operate Time : 15 mSec. Max.
Release Time : 10 mSec. Max.
Against overloads and short-circuits: No
Against overvoltages (*): No
None Galvanic isolation
Switch frequency:
Mechanism
Resistor/light load
Sensitive load
GSM parameter:
Type of mobile wireless service
Operating frequency for GPRS transmission / with downlink / maximum for GPRS transmission / with uplink / maximum
Other parameters:
Ethernet interface
10Hz
2Hz
0.5Hz
SMS, GPRS
850MHz,900MHz,1800MHz,1900MHz,
80 kbit/s
40 kbit/s
No Yes
366
Voice alarming
Weight
Function blocks
No
Approx.500g
512 blocks
RTC accuracy : MAX ±2S/day
RTC Backup at 25 °C
Program and settings Backup
Data Power-off retentivity
Short-circuit protection
Cycle time
Connection cables
Ambient temperature
20 days
10 Years
Yes
External fuse required typ. 0.6ms ➞ 8.0ms
2 x 1.5 mm² or 1 x 2.5 mm²
-20 to + 55 ºC
Storage temperature
Certification
Mounting
Dimensions
–40 ºC to + 70 ºC
CE
On 35 mm standard mounting rail, 4 MW, or wall-mounting
W x H x D (95*90*67 mm)
Programming cable PC cable, (RS232 or USB)
Third party device(HMI) <=> xLogic Yes (work as modbus master or slave)
Extensions
RS485
LCD
Yes(8 PCS EXM-E expansion)
Yes,( PRO-RS485 cable or EXM-E-RS485 module is required)
Yes(4*16 characters)
CPU Model
Power supply:
Nominal voltage
Operating limits
Immunity from micro power cuts
Max. Startup current
Max. absorbed power
Protection against polarity inversions
Input parameters:
Input No
Digital input
Analogue input
EXM-12DC-DAI-R
DC 12-24V
DC 10.8-28.8V
Typ.5 ms
EXM-8DC-PT100-R
Max. 0.5A
Normal: 3.3 W (10.8V dc) ; 3.8 W (28.8V dc)
Transient Current: Max. 1A (DC12V)
Yes
8 ( I1-I8 )
6 ( I1-I2,I5-I8 )
2 ( I1-I2)(0..10V
+2(I3-I4)(0/4...20mA)
DC)
4 (2pt100+ I3-I4 )
2(I3-I4)
Digital inputs
EXM-12DC-DA-R-VN
8 ( I1-I8 )
8 ( I1-I8 )
4(I1-I4)(0...10V)
367
Input voltage
Input signal0
Input signal1
Input current
DC0-28.8V
< 5V DC; <1mA
> 8 V DC;>1.7mA
2.3mA @ 10.8V dc
2.6mA @ 12.0 V dc
5.2 mA @ 24 V dc
6.3 mA @ 28.8 V dc
0 to 1 :<1 ms ;1 to 0 :<1 ms
60k Hz(I7--I8) None
Response time
Maximum frequency counting
Sensor type
Input type
Isolation between power supply and inputs
Isolation between inputs
Inputs used as digital inputs
Input voltage
Input signal0
Input signal1
Input current
Contact or 3-wire PNP
Resistive
None
None
I1-I2
Response time
Maximum frequency
Sensor type
Input type counting
Isolation between power supply and inputs
Isolation between inputs
Inputs used as analog inputs
Measurement range
Input impedance
Input voltage
Resolution
Accuracy at 25 °C
DC0-28.8V
< 5V DC;<0.1mA
> 8 V DC;>0.3mA
0.4mA @ 10.8V dc
0.5mA @ 12.0 V dc
1.2mA @ 24 V dc
1.5mA @ 28.8 V dc
0 to 1 :Typ. 1.5 ms ;1 to
0 :Typ. 1.5 ms
Typ.:4 HZ
Contact or 3-wire PNP
Resistive
None
None
( I1-I2 )
DC 0---10V(I1-I2)
Min, 24KΩ ; Max. 72KΩ
28.8 V DC max
10bit ,0.01V
± (Max.0.02)V
None
--
--
--
--
--
--
--
--
--
--
None
--
--
--
--
--
368
60k Hz(I7--I8)
I1-I4
DC0-28.8V
< 5V DC;<0.1mA
> 8 V DC;>0.3mA
0.4mA @ 10.8V dc
0.5mA @ 12.0 V dc
1.2mA @ 24 V dc
1.5mA @ 28.8 V dc
0 to 1 :Typ. 1.5 ms ;1 to
0 :Typ. 1.5 ms
Typ.:4 HZ
Contact or 3-wire PNP
Resistive
None
None
(I1-I4)
DC 0---10V(I1-I4)
Min, 24KΩ ; Max. 72KΩ
28.8 V DC max
10bit ,0.01V
± (Max.0.02)V
Accuracy at 55 °C
Isolation between analog channel and power supply
Cable length
± (Max.0.04)V
None
--
--
10 m max. shielded and twisted
--
Current input(I3-I4)
Measurement range
Resolution
Accuracy at 25 °C
Cycle time for analog value generation analog inputs( AI1-AI2 )
Input No
Digital input
Analogue input
Resolution
Measuring range
Cable length
0/4...20mA(I3--I4)
0.02mA
0.05mA
Typ. 50 ms
None
--
--
--
--
--
None
--
--
--
--
2 (AI1 –AI2)
None
2 Channels PT100
0.3℃
-50℃ to +200℃
10 m max.
shielded and twisted
Output parameters:
Output No.
Output type
Continuous current
Max. breaking voltage
Max. Allowable Power Force 1250VA 300W
Electrical
Expectancy durability 105 Operations at Rated Resistive Load
Mechanical life 107 Operations at No Load condition
Response time
4 (Q1-Q4)
4Relay output
Resistive load 10A/Inductive load 2A
AC 250 V DC 30 V
Built-in protections
Operate Time : 15 mSec. Max.
Release Time : 10 mSec. Max.
Against overloads and short-circuits: No
Against overvoltages (*): No
None Galvanic isolation
Switch frequency:
Mechanism
Resistor/light load
Sensitive load
GSM parameter:
Type of mobile wireless service
10Hz
2Hz
0.5Hz
SMS, GPRS
± (Max.0.04)V
None
10 m max.
shielded and twisted
None
--
--
--
--
--
369
Operating frequency for GPRS transmission / with downlink / maximum for GPRS transmission / with uplink / maximum
Other parameters:
Ethernet interface
Voice alarming
Weight
Function blocks
RTC accuracy :
RTC Backup at 25 °C
Program and settings
Backup
Data Power-off retentivity
Short-circuit protection
Cycle time
Connection cables
Ambient temperature
Storage temperature
Certification
Mounting
Dimensions
Programming cable
Third party device(HMI)
<=> xLogic
Extensions
RS485
LCD
850MHz,900MHz,1800MHz,1900MHz,
80 kbit/s
40 kbit/s
No
No
Approx.500g
512 blocks
MAX ±2S/day
20 days
10 Years
Yes
External fuse required typ. 0.6ms ➞ 8.0ms
2 x 1.5 mm² or 1 x 2.5 mm²
-20 to + 55 ºC
–40 ºC to + 70 ºC
CE
On 35 mm standard mounting rail, 4 MW, or wall-mounting
W x H x D (95*90*67 mm)
PC cable, (RS232 or USB)
Yes (work as modbus master or slave)
Yes (8 PCS EXM-E expansion)
Yes,( PRO-RS485 cable or EXM-E-RS485 module is required)
Yes(4*16 characters)
Yes
Yes
CPU model
Power supply:
Nominal voltage
Operating limits
Immunity from micro power cuts
Max. Startup current
Max. absorbed power
EXM-12DC-DA-RT-WIFI
DC 12-24V
DC 10.8-28.8V
Typ.5 ms
Max. 0.25A
3.5 W (10.8V dc) ; 4 W (28.8V dc)
Protection against polarity inversions Yes
EXM-12DC-DA-RT-GWIFI
370
Input parameters:
Input No
Digital input
Analogue input
Digital inputs( I5-I8 )
Input voltage
Input signal0
Input signal1
Input current
Response time
8 ( I1-I8 )
8 ( I1-I8 )
4 ( I1-I4)(0..10V DC)
DC0-28.8V
< 5V DC; <1mA
> 8 V DC;>1.7mA
2.3mA @ 10.8V dc
2.6mA @ 12.0 V dc
5.2 mA @ 24 V dc
6.3 mA @ 28.8 V dc
0 to 1 :<1 ms ;1 to 0 :<1 ms
Maximum counting frequency
Sensor type
Input type
Isolation between power supply and inputs
Isolation between inputs None
Inputs used as digital inputs( I1-I4 )
Input voltage
Input signal0
DC0-28.8V
< 5V DC;<0.1mA
Input signal1
Input current
60k Hz(I7--I8)
Contact or 3-wire PNP
Resistive
None
> 8 V DC;>0.3mA
0.4mA @ 10.8V dc
0.5mA @ 12.0 V dc
1.2mA @ 24 V dc
1.5mA @ 28.8 V dc
0 to 1 :Typ. 1.5 ms ;1 to 0 :Typ. 1.5 ms Response time
Maximum counting frequency
Sensor type
Input type
Typ.:4 HZ
Contact or 3-wire PNP
Resistive
None Isolation between power supply and inputs
Isolation between inputs
Inputs used as analog inputs( I1-I4 )
None
Measurement range
Input impedance
DC 0---10V
Min, 24KΩ ; Max. 72KΩ
Input voltage
Resolution
Accuracy at 25 °C
28.8 V DC max
10bit ,0.01V
± (Max.0.02)V
371
Accuracy at 55 °C
Isolation between analog channel and power supply
Cable length
Output parameters:
Output No.
Output type
Continuous current
Max. breaking voltage
Max. Allowable Power Force
Electrical durability Expectancy
Mechanical life
Response time
Built-in protections
± (Max.0.04)V
None
10 m max. shielded and twisted
4 (Q1-Q4)
2Relay output +2 Transistor(PNP) output
(Q1-Q2)Resistive load 10A/Inductive load 2A
(Q3-Q4) Max. 0.3 A per channel
(Q1-Q2) AC 250 V DC 30 V
(Q3-Q4) ≤ Supply voltage
(Q1-Q2)1250VA 300W
(Q3-Q4) 9 W
105 Operations at Rated Resistive Load
107 Operations at No Load condition
Operate Time : 15 mSec. Max.
Release Time : 10 mSec. Max.
Against overloads and short-circuits: No
Against overvoltages (*): No
None
1K HZ
Galvanic isolation
PWM frequency(Q3-Q4)
PWM cyclic ratio(Q3-Q4)
PWM accuracy at 120Hz(Q3-Q4)
0 to 100 %
< 0.5 % (20 % ➞ 80 %) load at 10 mA
Max. Breaking current PWM(Q3-Q4) 50 mA
Switch frequency:
Mechanism
Resistor/light load
Sensitive load
10Hz
2Hz
0.5Hz
Built-in wireless parameters:
Support 802.11b/g/n wireless standards
Support TCP/IP/UDP network protocols
Support work as STA/AP mode
Support Router/Bridge mode networking
Support Transparent/Agreement Transmission Mode(Transparent used by EXM CPU)
Support Friendly Web Configuration Page or configuration by eSmsconfig
Outdoor 100m with 3dBi antenna and indoor 40m
FCC /CE Certificated
GSM parameter
Type of mobile wireless service
Operating frequency
None
--
SMS, GPRS
850MHz,900MHz,1800MHz,1900MHz,
372
for GPRS transmission / with downlink / maximum for GPRS transmission / with uplink / maximum
Other parameters:
Ethernet port:
Xlogic<--->Xlogic(byWifit)
Xlogic<--->Etherne/Internet:
Weight
Function blocks
--
Built-In(10M/100M)
1 xlogic works as server can connect 32 client xlogics.
xlogic works as TCP server or TCP client
Approx.500g
512 blocks
80 kbit/s
40 kbit/s
RTC accuracy : MAX ±2S/day
RTC Backup at 25 °C
Program and settings Backup
Data Power-off retentivity
Short-circuit protection
Cycle time
Connection cables
Ambient temperature
Storage temperature
Certification
Mounting
Dimensions
Programming cable
20 days
10 Years
Yes
External fuse required typ. 0.6ms ➞ 8.0ms
2 x 1.5 mm² or 1 x 2.5 mm²
-20 to + 55 ºC
–40 ºC to + 70 ºC
CE
On 35 mm standard mounting rail, 4 MW, or wall-mounting
W x H x D (95*90*67 mm)
PC cable, (RS232 or USB)
Third party device(HMI) <=> xLogic Yes (work as modbus master or slave)
Extensions Yes (8 PCS EXM-E expansion)
RS485
LCD
Yes,( PRO-RS485 cable or EXM-E-RS485 module is required)
Yes(4*16 characters)
Extension Units
Power supply:
Nominal voltage
Operating limits
Immunity from micro power cuts
Max. Startup current
Max. absorbed power
Protection against polarity
EXM-E-8AC-R
AC110V-240V
AC85 - 265 V
---
---
34mA (85V ac) ;
26mA (265V ac)
Yes
373
EXM-E-8DC-DA-R
DC 12-24V
DC 10.8-28.8V
Typ. 5 ms
Max. 0.25A
1.1 W (10.8V dc) ;
1.2 W (28.8V dc)
Yes
inversions
The main frequency range
Input parameters:
Input No
Digital input
Analogue input
Input voltage
Input signal0
Input signal1
Input current
47-63Hz
4 ( I1-I4 )
4 ( I1-I4 )
None
AC0-240V
AC0-40V;<0.03mA
AC79-240V;>0.06mA
---
Input Response Time Delay time at 0 to 1:
120V AC :Typ. 50 ms
240V AC :Typ. 30 ms
Delay time at 1 to 0:
120V AC :Typ. 90 ms
240V AC :Typ.100 ms
Typ. 4Hz Maximum counting frequency
Sensor type
Isolation between power supply and inputs
Isolation between inputs
Protection against polarity
Contact or 3-wire PNP
None
None
Yes inversions
Inputs used as analog inputs( I1-I4 )
Measurement range
Input impedance
Input voltage
Resolution
---
---
---
---
Accuracy at 25 °C
Accuracy at 55 °C
Isolation between analog channel and power supply
Cable length
Output parameters:
Output No.
Output type
---
---
---
---
4 (Q1-Q4)
Relay output
---
4 (I1-I4 )
4 (I1-I4 )
4 ( I1-I4)(0..10V DC)
DC 0-28.8V
< 5V DC;<0.1mA(I1-I4),<1mA(I5-I8)
> 8 V DC;>0.3mA(I1-I4),>1.7mA(I5-I8)
0.4mA(I1-I4),2.3mA(I5-I8),@ 10.8V dc
0.5mA(I1-I4),2.6mA(I5-I8),@ 12.0 V dc
1.2mA(I1-I4),5.2mA(I5-I8),@ 24 V dc
1.5mA(I1-I4),6.3mA(I5-I8),@ 28.8 V dc
Delay time at 0 to 1 :
Typ. 1.5 ms (I1-I4),<1ms(I5-I8);
Delay time at 1 to 0 :
Typ. 1.5 ms(I1-I4),<1ms(I5-I8);
Typ.:4 HZ
Contact or 3-wire PNP
Resistive
None
None
DC 0---10V
Min, 24KΩ ; Max. 72KΩ
28.8 V DC max
9bit ,0.015V
± (Max.0.02)V
± (Max.0.04)V
None
10 m max. shielded and twisted
374
Continuous current
Max. breaking voltage
Max. Allowable Power Force 1250VA /300W(Relay)
Electrical durability
Expectancy
10 5 Operations at Rated Resistive Load(Relay)
Mechanical life
Resistive load 10A/Inductive load 2A (Relay)
AC 250 V /DC 110 V(Relay)
Response time
10 7 Operations at No Load condition(Relay)
---
Operate Time : 15 mSec. Max.(Relay)
Built-in protections
Release Time : 10 mSec. Max.(Relay)
Against short-circuits: None
Against overvoltages and overloads: None
Switch frequency:
Mechanism
Resistor/light load
Sensitive load
Other parameters:
Weight
Connection cables
Ambient temperature
Storage temperature
Certification
Mounting
Dimensions
10Hz
2Hz
0.5Hz
Approx.250g
2 x 1.5 mm² or 1 x 2.5 mm²
-20 to + 55 ºC
–40 ºC to + 70 ºC
CE
On 35 mm standard mounting rail, 4 MW, or wall-mounting
W x H x D (48*90*64 mm)
Extension Units
Power supply:
Nominal voltage
Operating limits
Immunity from micro
EXM-E-AI-I
DC 12-24V
DC 10.8-28.8V
Typ. 5 ms
EXM-E-PT100 EXM-E-AQ-V EXM-E-AQ-I
DC 24V
DC 15-28.8V
DC 12-24V
DC 10.8-28.8V
375
power cuts
Max. Startup current
Max. absorbed power
Protection against polarity inversions
Input parameters:
Input No
Digital input
Analogue input
Analog inputs
Measurement range
Resolution
Accuracy at 25 °C
Isolation between analog channel and power supply
Cable length
Output parameters:
Output No.
Output type
Resolution
Accuracy at 25 °C
Other parameters:
Weight
Short-circuit protection
Connection cables
Ambient temperature
Storage temperature
Certification
Mounting
Dimensions
Max. 0.25A
3.5 W (10.8V dc) ; 4.5 W (28.8V dc)
Yes
4 ( I1-I4 )
None
I1-I4(0/4...20mA)
0/4...20mA
0.02mA
Max. 0.05mA
None
2 PT100
None
2PT100
-50℃--200℃
0.5℃
< 1 ℃
None
10 m max. shielded and twisted
---
---
---
---
---
---
---
---
---
---
2(AQ1-AQ2)
0...10V
0.01V
0.02V
Approx.250g
External fuse required
2 x 1.5 mm² or 1 x 2.5 mm²
-20 to + 55 ºC
–40 ºC to + 70 ºC
CE
On 35 mm standard mounting rail, 4 MW, or wall-mounting
W x H x D (48*90*64 mm)
0...20mA
0.02mA
0.05mA
RS485 communication module for ELC-12-N Ethernet CPU
(EXM-E-RS485)
Power supply:
Nominal voltage
Operating limits
Immunity from micro power cuts
Max. Startup current
EXM-E-RS485
DC 12-24V
DC 10.8-28.8V
Typ. 5 ms
Max. 0.1A
376
Max. absorbed power 1.5 W (10.8V dc) ; 1.8W W (28.8V dc)
Protection against polarity inversions Yes
Input parameters:
None
Output parameters:
None
Other parameters:
Weight
Short-circuit protection
Connection cables
Ambient temperature
Storage temperature
Certification
Mounting
Dimensions
Approx.250g
External fuse required
2 x 1.5 mm² or 1 x 2.5 mm²
-20 to + 55 ºC
–40 ºC to + 70 ºC
CE
On 35 mm standard mounting rail, 4 MW, or wall-mounting
W x H x D (48*90*64 mm)
377
A.3 Switching capacity and service life of the relay outputs
Ohmic load
Figure A Switching capacity and service life of the contacts with ohmic load (heating)
Inductive load
Figure B Switching capacity and service life of the contacts with high inductive load (contactors, solenoid coils, motors).
378
Revision Description
379
380
advertisement
Key Features
- Compact and expandable design
- Combines GSM/GPRS modem, PLC controller, data logger, Ethernet module
- Multiple communication capabilities
- Real-time clock and calendar support
- Support for SMS, Call-In, Email, Ring
- DIN-rail and panel-mounted options
- 120V/240V AC or 12V and 24V DC versions
- Off-line operation mode for configuration and testing
Frequently Answers and Questions
What is the x-Messenger?
What are some applications of the x-Messenger?
How can I configure the x-Messenger?
What are the different versions of the x-Messenger?
How do I install the x-Messenger?
Related manuals
advertisement
Table of contents
- 7 Contents
- 11 Chapter 1 General Introduction to x-Messenger
- 12 1.1 Overview
- 12 1.2 Highlight feature
- 13 Applications
- 14 2.1 Application overview
- 14 2.2 Application architecture
- 18 Chapter 3 Hardware models and resources
- 18 3.1 Naming Rules of EXM Series
- 18 3.2 Hardware model selection
- 20 3.3 Resources
- 20 3.3.1 GSM /GPRS module built- in
- 21 3.3.1.1 How to establish the connection between x-Messenger and PC via GPRS?
- 26 3.3.1.2 E-mail and how to set?
- 28 3.3.1.3 How to change the register value(F,Q,AQ,AF,REG) or phonebook via SMS
- 35 3.3.1.4 How to modify the PIN via SMS
- 36 3.3.1.5 How to modify the GPRS Parameters and Email parameters via SMS
- 40 3.3.1.6 How to modify the email address of the receiver via SMS?
- 42 3.3.2 Voice alarm
- 56 3.3.3 Ethernet Interface
- 83 3.3.4 SD card Data logging
- 84 3.3.5 Communication Interface
- 85 3.3.6Multiple Modbus communication protocol
- 88 3.3.7 LCD panel instruction
- 91 3.3.8 Antenna
- 91 3.4 Structure & dimension
- 93 Chapter 4 Installing/removing EXM
- 93 4.1 DIN rail mounting
- 95 4.2 Wall-mounting
- 96 4.3 wiring EXM
- 96 4.3.1 Connecting the power supply
- 97 4.3.2 Connecting x-Messenger inputs
- 99 4.3.3 Connecting EXM Outputs
- 101 Chapter 5 Configuring & Software-standard mode
- 101 5.1 System requirements
- 102 5.2 General
- 103 5.3 Create connection
- 103 5.4 Edit telephone book
- 103 5.5 Standard mode settings
- 104 5.5.1 Device types
- 104 5.5.2 Automatic provider search
- 104 5.5.3 Manual provider search
- 105 5.6 Status messages
- 105 5.7 Input configuration
- 105 5.7.1 General
- 106 5.7.2 Digital inputs
- 106 5.7.2.1 Parallel message handling
- 107 5.7.2.2 Time delayed message for input ON
- 108 5.7.2.3 Time delayed message for output OFF
- 108 5.7.3 Analogue inputs
- 108 5.7.3.1 Scaling and units
- 112 5.7.3.3 Message delay
- 112 5.7.3.4 Message block
- 113 5.8 Output configuration
- 113 5.8.1 General
- 113 5.8.2 Timer function
- 114 5.8.3 CALL-IN function
- 114 5.8.4 I/O status remote request
- 115 5.8.5 Digital inputs
- 115 5.8.6 Analogue inputs
- 115 5.8.7 Outputs
- 116 Chapter 6 Configuring & Software-customized mode
- 117 6.1 x-Messenger Functions
- 117 6.2 General Input & Output functions
- 117 6.2.1 Inputs
- 118 6.2.2 Cursor keys
- 118 6.2.3 Outputs
- 118 6.2.4 Permanent logical levels HI and LO
- 119 6.2.5 Open Connector
- 119 6.2.6 Panel Key
- 120 6.2.7 Shift register bits
- 120 6.2.8 Analog inputs
- 121 6.2.9 F (digital flag)
- 121 6.2.10 AF (Analog flag)
- 122 6.2.11 SMS message input
- 124 6.2.12 SMS message output
- 129 6.2.13 Sms message Input Output
- 133 6.2.14 GPRS Connect
- 135 6.2.15 GPRS Data Upload
- 141 6.3 Basic functions list – GF
- 142 6.3.1 AND
- 143 7.3.2 AND with edge evaluation
- 144 6.3.3 NAND
- 145 6.3.4 NAND with edge evaluation
- 146 6.3.5 OR
- 147 6.3.6 NOR
- 148 6.3.7 XOR
- 148 6.3.8 NOT
- 149 6.4 Basics on special functions
- 149 6.4.1 Designation of the inputs
- 150 6.4.2 Time response
- 151 6.4.3 Backup of the real-time clock
- 151 6.4.4 Retentivity
- 151 6.4.5 Parameter protection
- 151 6.4.6 Calculating the gain and offset of analog values
- 154 6.5 Special functions list – SF
- 156 6.5.1 On-delay
- 158 6.5.2 Off-delay
- 159 6.5.3 On-/Off-delay
- 161 6.5.4 Retentive on-delay
- 162 6.5.5 Wiping relay (pulse output)
- 163 6.5.6 Edge triggered wiping relay
- 165 6.5.7 Asynchronous pulse generator
- 166 6.5.8 Random generator
- 168 6.5.9 Stairway lighting switch
- 169 6.5.10 Multiple function switch
- 171 6.5.11 Weekly timer
- 174 6.5.12 Yearly timer
- 180 6.5.13 Up/Down counter
- 182 6.5.14 Hours counter
- 185 6.5.15 Threshold trigger
- 186 6.5.16 Latching relay
- 188 6.5.17 Pulse relay
- 189 6.5.18 Message text
- 196 6.5.18.1 How to change parameters of blocks in displayed message ?
- 198 6.5.19 Softkey
- 199 6.5.20 Shift register
- 201 6.5.21 Analog comparator
- 204 6.5.22 Analog threshold trigger
- 207 6.5.23 Analog amplifier
- 210 6.5.25 Analog differential trigger
- 212 6.5.26 Analog multiplexer
- 214 6.5.27 System cover
- 215 6.5.28 Pulse Width Modulator (PWM)
- 219 6.5.29 Analog Ramp
- 221 6.5.30 Analog Math
- 223 6.5.31 Analog math error detection
- 225 6.5.32 Modbus Read
- 232 6.5.33 Modbus Write
- 236 6.5.34 Data latching relay
- 238 6.5.35 PI controller
- 249 6.5.36 Memory write
- 255 6.5.37 Memory Read
- 259 6.5.38 Word to Bit
- 261 6.5.39 Bit to Word
- 264 6.5.40 Device Reset
- 265 6.5.41 Comport Status
- 269 6.5.42 Analog filter
- 270 6.5.43 Max/Min
- 274 6.5.44 Average value
- 275 6.5.45 Astronomical clock
- 277 6.5.46 Stopwatch
- 279 6.5.47 Cam Control
- 280 6.5.48 Angular Cam Timer
- 281 6.5.49 Pumps Management
- 283 6.5.50 Defrost
- 285 6.5.51 Comparison of 2 values
- 286 6.5.52 Multicompare
- 287 6.5.53 Compare in zone
- 288 6.5.54 Conversion Word bits
- 289 6.5.55 Conversion bits Word
- 289 6.5.56 Demultiplexer
- 290 6.5.57 Multiplexing
- 291 6.5.58 Multiplexer
- 292 6.5.59 Square Boot
- 292 6.5.60 Sin Cos
- 293 6.6 Enter into “Customized mode
- 295 6.7 Main Functions
- 296 6.8 Operation Instructions of Customized Mode
- 296 6.8.1 Menu Bar
- 296 6.8.1.1 File
- 297 6.8.1.2 Edit
- 297 6.8.1.3 Tools
- 298 6.8.1.4 SMS
- 300 6.8.1.5 View
- 300 6.8.1.6 Help
- 301 6.8.2 Toolbar
- 302 6.8.3 Programming Toolbar
- 303 6.8.4 Simulation Tool and status window
- 306 6.9 Basic Operation
- 306 6.9.1 Open File
- 306 6.9.1.1 Open New File
- 307 6.9.1.2 Open Existed Document
- 308 6.9.2 Edit Function Diagram Program
- 308 6.9.2.1 Place Function Block
- 309 6.9.2.2 Edit Property of Function Block
- 310 6.9.2.3 Setup link
- 312 6.9.2.4 Delete Function Block or Delete Link
- 312 6.10 Simulation Running
- 314 6.11 Save and Print
- 315 6.12 Modify Password and transfer the Program
- 317 6.13 How to prevent your program from being copied/stolen?
- 319 6.14 On-line monitoring/test circuit program
- 325 Chapter 7 Description of the WIFI module built-in the EXM WIFI CPU
- 326 7.1 Functional description
- 331 7.2 OPERATION GUIDELINE
- 340 7.3 10/100M Ethernet Interface
- 341 7.4 HF-A11 Ethernet Interface Networking (As AP)
- 343 7.5 How to Configure the wifi module by the eSmsConfig.exe
- 352 7.6 How to configure WIFI connection (TCP protocol) among EXM WIFI CPUs?
- 363 Appendix
- 363 A Technical data