Extron electronics | TPX 88 Series | User`s manual | Extron electronics TPX 88 Series User`s manual

User’s Manual
VTT001 and VTR001
Twisted Pair Transmitter and Receiver
68-760-01 Rev. G
06 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions
in the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product's enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation
et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de
pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et
consignes marqués sur le matériel ou présentés dans la documentation
utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni
d’outils non recommandés par le fabricant du matériel car cela
risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau
durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre
instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de
operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad
para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones
marcadas en el equipo o en la documentación del usuario, deben ser
obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main
power system with a grounded (neutral) conductor. The third (grounding) pin is
a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all
power cords from the rear of the equipment, or the desktop power module (if
detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to
be stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced.
Replace it only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation
principale comportant un fil de terre (neutre). Le troisième contact (de mise à la
terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du
module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient
pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne
doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,
ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces
ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la
batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype
equivalent recommande par le constructeur. Mettre au reut les batteries usagees
conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit
einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der
dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar.
Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,
sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen
Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht
im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder
unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem
Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes
sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in
keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die
Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse
aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen
Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten
blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.
Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen
Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor
neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la
acometida de alimentación eléctrica al equipo, desenchufar todos los cables de
alimentación en el panel trasero del equipo, o desenchufar el módulo de
alimentación (si fuera independiente), o desenchufar el cable del receptáculo de
la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se
deben instalar en lugares donde no sean pisados ni apretados por objetos que se
puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para
evitar riesgo de electrocución, no intentar personalmente la reparación/
mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar
expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
ᅝܼ乏ⶹ•Ё᭛
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒໛⫼᠋᠟‫ݠ‬Ё
᳝䞡㽕ⱘ᪡԰੠㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺ਞ⫼᠋䆹䆒໛ᴎ໇‫ݙ‬᳝
䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢк• 䑩ㅸỀ䑩嬦嫿⡈↎⼆枼敆嬼⶷䍇夤ㆁ㙊
⫊₩⏍Ề䑩嬵㕏ɿ
ֱᄬ䇈ᯢк• 䑩ㅸⷕ἞⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề䑩ɿ
䙉ᅜ䄺ਞ• 䑩ㅸⷕ徶⫉ᷨ␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊₩
⏍㐎ẝ嬵㕏ɿ
䙓‫ܡ‬䗑ࡴ• ᵎ壂Ề䑩嬦ᷨ␂⋃⒇㯢㙊㋩劑䗅⴦₸ㅗ弾
⇡嫿⡈澤Ḧ忀₎⊲斪ɿ
䄺ਞ
⬉⑤• 嬦嫿⡈⌫倾Ề䑩ᷨ␂ᵋ㝈㕏䗅䑶㷑ɿ嫿⡈⼆枼
Ề䑩㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ䩭ᵊ㚢一澠♱一澡㕰
⫊₩嫿㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ
ᢨᥝ⬉⑤• ᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿
⡈⍏ㅗ㞍暣䑶㷑䗅䑶㷑一澤ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅
䑶㷑一ɿ
⬉⑤㒓ֱᡸ• ⣦Ⓟⵄ一澤忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ
㓈ᡸ•ㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ᷻⎙弜垍ɿ嫿⡈⃆
怩㯢㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿᵻ忀₎℻䋱大䑶⊲斪
ᵎ壂儫ⴲ嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ
䗮亢ᄨ• 㙊ᷜ嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦
敳㪣㙻⃆㒐だ₄ḷ弈䀮ɿᵎ壂䑩Ḽẖᵝ壀㉢Ẑ彛
栏⪕ɿ
䫖⬉∴• ᵎ㪤䞯䗅㘵㊣䑶㮡ṛ㙊䅇㿹䗅⊲斪ɿ⼆枼Ề䑩
ᵏ⋃⫷㋩劑䗅䘹⍍ㅗ䘹弒⛌⌸䗅䑶㮡ɿ㉊䂨䑠ᷨ⋃
䗅⸻嫯⡅䍇ⷠ⹄䑶㮡ɿ
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
N This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
Precautions, cont’d
Quick Start Guide — VTT001/VTR001
Installation and service must be performed by authorized
personnel only. These units must be installed in
accordance with national and local electrical codes.
CAUTION
Step 1
Power off all devices and disconnect them from the power source.
Step 2
Connect the RJ-45 connectors of the transmitter and receiver to
either end of the UTP cable. If making your own cable between the
transmitter and receiver, see “Installation” in chapter 2 for the RJ-45
wiring termination diagram.
RJ-45 termination must comply with the TIA/EIA T568A or
TIA/EIA T568B wiring standards.
Do not connect the transmitter/receiver to a computer data
or telecommunications network.
CAUTION
Step 3
Connect the external power supply to the transmitter, or the
receiver, or to both.
Both transmitter and receiver have remote power capability.
For transmission distances up to 300 feet, the power is
required at either the transmitter or the receiver. Greater
distances require power to be applied locally to both
transmitter and receiver.
Step 4
Using the 15-pin front panel HD connectors, attach a computer
input to the transmitter and a display output to the receiver. See the
example application diagram below.
Extron
CPM101
Mounting Frame
Extron
VTR001 MAAP
Twisted Pair
Receiver
R
WE
PO
OU
TP
UT
VT
R0
01
MA
AP
LCD Projector
Extron
CPM101
Extron
Skew-Free™ A/V UTP
Cable
(up to 500')
Mounting Frame
R
WE
PO
EO
VID
INP
UT
VT
T0
01
MA
AP
Extron
VTT001 MAAP
Twisted Pair Transmitter
Laptop
VTT001 and VTR001 • Quick Start Guide
QS-1
Quick Start Guide — VTT/VTR, cont’d
Step 5
Plug in the DC power supply to the AC power source, and power on
the transmitter/receiver modules and the input and output devices.
Each module’s Power LED is lit while the unit receives power.
Step 6
Test the system. If there is no picture output, verify that each
module has been correctly cabled and wired and all devices are
receiving power. If needed, power off the system and modules,
correct the wiring, then reconnect power.
Step 7
For the VTR001 series, set the sharpness control
located on the top of the receiver. See the
illustration on the right. Turning the control
clockwise increases sharpness and turning it
counterclockwise decreases sharpness.
Step 8
Sharpness
P
AR
SH
UT
TP
OU
For a non-tabletop installation, disconnect
power from the module(s) and other
devices, then disconnect all other cables.
VT
R0
01
MA
AP
Step 9
Mount the transmitter/receiver module into a double space MAAP
connector panel (CPM101/CPM200/CPM112R, etc.) or AAP panel.
Step 10
If these modules are to be wall-mounted, reconnect the twisted pair
cables prior to mounting.
Step 11
Mount the connector plate and module(s) into the wall/furniture or
rack. See chapter 2 for further mounting details.
If the transmitter or receiver is to be wall-mounted and the
power supply will be inaccessible, power must be applied to
the power supply before final mounting.
Step 12
Reconnect all disconnected cables and restore power to all devices.
The installation is now complete.
QS-2
VTT001 and VTR001 • Quick Start Guide
Table of Contents
Chapter 1 • Introduction .......................................................... 1-1
Features ......................................................................... 1-3
Chapter 2 • Installation ............................................................. 2-1
Rear Panel Connectors ........................................................ 2-2
Front Panel Connector and Indicator ...................... 2-4
Cabling and Setup ................................................................. 2-6
Compatibility with other Extron products ............................ 2-7
Cable testing .......................................................................... 2-8
Equalizing pair skew .............................................................. 2-8
Sharpness adjustment ......................................................... 2-10
Mounting .............................................................................. 2-10
Preparing the wall box ..................................................... 2-10
Wall box mounting .......................................................... 2-12
Wall bracket mounting ..................................................... 2-13
AAP mounting ................................................................. 2-14
UL rack mounting guidelines ............................................ 2-14
Rack mounting ................................................................. 2-15
Appendix • Reference Information .................................. A-1
Specifications ......................................................................... A-2
Parts List .................................................................................... A-5
VTT001 MAAP and VTR001 MAAP ...................................... A-5
VTT001 and VTR001 tabletop .............................................. A-5
VTT001 AAP and VTR001 AAP ............................................ A-5
Included parts ........................................................................ A-5
Skew-Free™ A/V UTP cables ................................................. A-6
Other accessories .................................................................. A-6
All trademarks mentioned in this manual are the properties of their respective
owners.
68-760-01 Rev. G
06 09
VTT001 and VTR001 • Table of Contents
i
Table of Contents, cont’d
ii
VTT001 and VTR001 • Table of Contents
VTT001/VTR001
1
Chapter One
Introduction
Features
Introduction, cont’d
Introduction
The Extron VTT001 twisted pair transmitter series and VTR001
twisted pair receiver series provide a system for sending VGA,
RGBHV, and RGBS signals up to 500 feet (150 meters) over
Extron Skew-Free™ A/V UTP cable. They can also send these
signals over CAT 5/5e/6 UTP cable.
Both transmitter and receiver have remote power capability.
For transmission distances up to 300 feet, the applied power is
required at either the transmitter or the receiver. Greater
distances require power to be applied locally to both transmitter
and receiver.
Depending on the model, both transmitter and receiver
modules may be mounted in a wall, a rack, or in other Extron
products that accept a double-sized MAAP connector panel
(CPM101, CPM200/CPM112R, etc.), or Extron AAP mounting
products; or they may be set on a tabletop. The MAAP models
come in a black or white finish; the AAP models come in black,
white, or gray finish; and the tabletop model comes in a black
finish.
The following table specifies the maximum recommended
transmission distances for the VTT001/VTR001 pair at 60 Hz.
Video
Resolution
Recommended
Maximum Range
640 x 480
500 feet
800 x 600
400 feet
1024 x 768*
300 feet
1280 x 960*
200 feet
1280 x 1024*
200 feet
1360 x 765
200 feet
1365 x 768
200 feet
1366 x 768
200 feet
1440 x 900
200 feet
1400 x 1050
200 feet
1600 x 1200*
150 feet
1920 x 1080
150 feet
* Resolutions marked with an asterisk (*) in the above
table have the same range specification at 75 Hz.
Extron recommends using at least 50’ of TP cable
between the transmitter and the receiver.
It is possible to exceed the recommended distances.
However, image quality may be reduced.
1-2
VTT001 and VTR001 • Introduction
Features
• Video sharpness control — Optimizes the video image for
different cable lengths between transmitter and receiver.
• Removable faceplate — The module faceplate may be
removed for table top use or attachment to an equipment
rack.
• Compatibility — The VTR001 receiver series also functions as
the receiver for output from the Extron IN1404XT video
scaler, Extron TP T 15HD A, TP T 15HD AV, TP T BNC,
TP T 15HD 45, TPX 88, TPX 88 A, and TP T BNC DA4.
• Remote power capability — Both transmitter and receiver
can be powered remotely when cable runs are 300 feet or
less.
VTT001 and VTR001 • Introduction
1-3
Introduction, cont’d
1-4
VTT001 and VTR001 • Introduction
VTT001/VTR001
2
Chapter Two
Installation
Rear Panel Connectors
Front Panel Connector and Indicator
Cabling and Setup
Installation, cont’d
Installation
Rear Panel Connectors
VTT001 MAAP
VTT001
TX
TX
9VDC-12VDC
500mA
9VDC-12VDC
500mA
1a
1a
2a
2b
VTT001 AAP
9VDC-12VDC
500mA
TX
1a
2a
Figure 2-1 — VTT001 MAAP, VTT001, and VTT001 AAP
rear panel views
The VTT001 MAAP/VTT001 AAP and VTT001 models
differ in how they are mounted. See “Mounting” in this
chapter.
VTR001 MAAP
VTR001
RX
RX
9VDC-12VDC
500mA
9VDC-12VDC
500mA
1b
1b
2a
2b
VTR001 AAP
9VDC-12VDC
500mA
RX
1b
2a
Figure 2-2 — VTR001 MAAP, VTR001, and VTR001 AAP
rear panel views
The VTR001 MAAP/VTR001 AAP and VTR001
models differ in how they are mounted. See “Mounting”
in this chapter.
2-2
VTT001 and VTR001 • Installation
1a
Transmitter output connector — A female RJ-45 connector on a
3" pigtail for the VTT001 MAAP and VTT001 AAP models, or
within the VTT001 model. Plug this connector to the UTP cable
going to the receiver.
CAUTION
1b
Receiver input connector — A female RJ-45 connector on a 3"
pigtail for the VTR001 MAAP and VTR001 AAP models, or
within the VTR001 model. Plug this connector to the UTP cable
coming from the transmitter.
CAUTION
Do not connect the receiver to a computer data or
telecommunications network.
Power
9 - 12VDC
Captive screw input power connector — Connect the included
12 VDC external power supply to the 2-pole female direct
insertion captive screw connector. The
VTT001 MAAP, VTT001 AAP, VTR001 AAP, +–
and VTR001 MAAP have this captive screw
connector.
RX
9VDC-12VDC
500mA
2a
Do not connect the transmitter to a computer data
or telecommunications network.
A
A
SECTION A–A
Power Supply
Output cord
To verify correct polarity before connection, check the power
supply’s no load output with a voltmeter.
The two power supply leads must be kept separated
while the power supply is plugged into an electrical
outlet. Remove power before wiring.
Do not tin the stripped power supply leads before
inserting them into the captive screw connector. Tinned
leads are not as securely attached as untinned leads and
could slip out.
VTT001 and VTR001 • Installation
2-3
Installation, cont’d
Both transmitter and receiver have remote power
capability. For transmission distances up to 300 feet, the
power is required only at either the transmitter or the
receiver. Greater distances will require power to be
applied to both transmitter and receiver.
2b
Power input jack — Connect the included 12 VDC external
power supply to this female jack. The VTT001 and the VTR001
use this power input connector. See the notes and warning for
2a .
Power plug
The male power plug that connects to this
input jack is shown on the right.
Tip (+)
Sleeve
Tip (+)
Sleeve
Front Panel Connector and Indicator
VTT001 MAAP
VTT001
3
3
MAAP
1
1
VTT001 AAP
3
INPUT
VTT001 AAP
1
Figure 2-3 — VTT001 MAAP, VTT001, and VTT001 AAP
front panel views
The VTT001 MAAP, VTT001 AAP, and VTT001 models
differ in how they are mounted. The AAP version has a
larger faceplate than the VTT001 MAAP.
2-4
VTT001 and VTR001 • Installation
VTR001
VTR001 MAAP
3
3
MAAP
2
2
VTR001 AAP
3
OUTPUT
VTR001 AAP
2
Figure 2-4 — VTR001 MAAP, VTR001, and VTR001 AAP
front panel views
The VTR001 MAAP, VTR001 AAP, and VTR001
models differ in how they are mounted. The AAP
version has a larger faceplate than the VTR001 MAAP.
1
Transmitter video input connector — A 15-pin HD VGA input
for all models. Plug a RGBHV/RGBS video signal into this
connector.
2
Receiver video output connector — A female 15-pin HD VGA
connector for all models. Connect a monitor, LCD projector, or
other display device to output an RGBHV or RGBS video signal.
3
Power LED indicator — The LED lights green whenever power
is applied.
VTT001 and VTR001 • Installation
2-5
Installation, cont’d
Cabling and Setup
To install the VTT001 MAAP, VTT001 AAP, VTT001 models and
the VTR001 MAAP, VTR001 AAP, VTR001 models, follow these
steps:
1.
Turn all of the equipment off and, if applicable, disconnect
it from the power source.
2.
Connect the RJ-45 connectors of the transmitter and
receiver to either end of the UTP cable. See “Cable
testing” and “Equalizing pair skew” in this chapter.
RJ-45 termination must comply with the TIA/EIA
T568A or TIA/EIA T568B wiring standards for all
connections, as shown on the following page.
Pins:
12345678
Pin
1&2
TIA/EIA T568A
Wire color
TIA/EIA T568B
Wire color
RGB Video
Signal
1 White-green
White-orange
Red/V. sync +
2 Green
Orange
Red/V. sync -
3 White-orange
White-green
Power
4 Blue
Blue
Green +
5 White-blue
White-blue
Green -
6 Orange
Green
Power
7 White-brown
White-brown
Blue/H. sync +
8 Brown
Brown
Blue/H. sync -
7&8
3&6 4&5
Twisted Pairs (4)
RJ-45
Connector
Figure 2-5 — RJ-45 pin terminations
For best results, use Extron Skew-Free™ A/V UTP
cable, available in bulk or in various preterminated
lengths. If necessary, regular CAT 5 cable may be used.
CAT 5e and CAT 6 cables are not recommended.
If you are using Enhanced Skew-Free™ A/V cable, use
the TIA/EIA T-568-A standard only.
2-6
VTT001 and VTR001 • Installation
3.
Connect the external power supply to the transmitter, the
receiver, or both. Both transmitter and receiver have
remote power capability. For transmission distances up to
300 feet, the applied power is only required at either the
transmitter or the receiver. Greater distances require
power to be applied locally to both transmitter and
receiver. See “Rear Panel Connectors” in this chapter.
4.
Connect an output display device to the 15-pin HD video
output connector of the receiver.
5.
Connect a RGBHV/RGBS video source to the 15-pin HD
video input connector of the transmitter.
6.
Power up the video input and output devices, then apply
power to the power supply and test for the display output.
Adjust the sharpness, if necessary. See “Sharpness
Adjustment” in this chapter. If a problem is encountered,
check all connections before proceeding further.
7.
If the previous display test was successful, power off and
disconnect all equipment, detach all cables, and install the
mountable transmitter and/or receiver. See “Mounting”
in this chapter.
If the transmitter or receiver is to be wall-mounted and
the power supply will be inaccessible, power must be
applied to the power supply before final mounting.
Compatibilty with other Extron products
The VTT001 series and VTR001 series products can
communicate with other Extron products. The following tables
indicate how the products interact.
TP T 15HD A TP T 15HD AV
VTR001 series
VTT001 series
TP T BNC
TP T BNC DA4
TP T AV
TP T 460
TP T 468
IN1404XT
TP T 15HD 45
B
A
A
A
A
A
A
A
A
TP R BNC AV
TP R BNC A
TP R AV
TP R 15HD A
A
A
B
A
A = RGB video only
B = incompatible
The VTT001 series and VTR001 series will not power
the compatible Extron products remotely.
VTT001 and VTR001 • Installation
2-7
Installation, cont’d
Cable testing
To ensure proper cable termination, each transmission cable
system that uses CAT 5e or CAT 6 cable should be tested
(Extron Skew-Free A/V UTP cable does not need to be tested).
Testing the cable from the RJ-45 connections at the transmitter
and receiver gives the most accurate indications of cable
problems.
There are two varieties of cable runs: simple runs, in which a
single cable is terminated only at the transmitter and receiver,
and complex runs, which can include patch bays and multiple
terminations and lengths of cable. In either case, the entire
cabling system should be tested.
A complete test measures cable length and tests the wire map,
attenuation, NEXT, PSNEXT, ELFEXT, PSELFEXT, return loss,
ACR and PSACR. All of these tests are critical for digital data
transfer. While all of these tests are important indicators of the
quality of the cable termination, the most critical testing
parameters for video transfer are wire map (T568A or T568B
termination) and pair length measurements. The largest
concern is equalization of skew between cable pairs. Cable
systems of 300 feet or less should exhibit no transmission
problems if they pass at least CAT 5e or preferably CAT 6-D5
channel certification testing.
The Microtest OMNI SCANNER 2 performs comprehensive
certification testing to the proposed CAT 6 standards. Other
manufacturers also make testing equipment. The tests include
advanced diagnostics for troubleshooting the cause and location
of many cable and termination problems. For simple
installation testing, the Microtest MICRO SCANNER PRO tests
wire map and cable length, including individual cable pair
length.
Equalizing pair skew
Pair skew issues are eliminated when you use Extron
Skew-Free™ A/V UTP cables.
The manufacturing process for CAT 5e or CAT 6 network UTP
cable leads to a condition called pair skew. For best results, pair
skew needs to be equalized when using the CAT 5e or CAT 6
cable in A/V applications. The design of Extron’s Skew-Free
A/V UTP cable minimizes pair skew to the point that
equalization is not required.
Skew exists between pairs when the physical length of one wire
pair is different from another. As the transmission cable length
2-8
VTT001 and VTR001 • Installation
increases, the amount of skew increases. Skew affects the
displayed image when the differential length between wire pairs
exceeds two feet, causing the timing of the red, green, and blue
video signals to appear out of alignment (horizontal registration
errors). A white vertical line on a black field can appear as
individual red, green, and blue lines that are close together; the
signal transmitted on the shortest wire pair leads the other
colors and appears to the left on the display.
S
H
A
R
P
UTP cable test equipment measures and reports wire pair
length. The report on the various
pair lengths can be used in
equalizing pair skew. The nominal
velocity of propagation (NVP —
the speed at which the signal
travels on the transmission line,
measured as a percentage of the
Sharpness
speed of light) of TP cable is very
close to that of conventional
coaxial cable. The difference in
NVP means that an additional
length of coax equal to the length
of pair skew, placed on the
receiver’s output, equalizes the
effects of pair skew.
UT
TP
OU
VT
R0
01
MA
AP
CAT 5 TP cable can lead to
registration errors between the red, green, and blue video
signals. Pair skew can be measured with test equipment or
identified by viewing a crosshatch test pattern closely to
determine if either the red, green, or blue video image leads
(appears to the left of) the other two video images. These
images can be minimized or eliminated by one of the following
methods:
•
Switch to Extron’s Enhanced Skew-Free A/V UTP cable.
•
Add a skew compensation cable equal to the length of
pair skew to the receiver’s output.
•
Install an Extron Skew Equalizer, SEQ 100 15HD
(part #60-676-01) or SEQ 100 BNC (part #60-675-01), on
the receiver’s video output and adjust the skew for the
leading video image.
VTT001 and VTR001 • Installation
2-9
Installation, cont’d
Sharpness adjustment
The longer the cable being used, the greater the signal loss. The
image sharpness may be enhanced by turning a peaking
adjustment screw located on the top of the receiver. Increased
peaking can compensate for detail (mid- and high-frequency)
loss from low bandwidth system components or capacitance in
long cables. Adjust this control using the included adjustment
tool (Extron part #100-043-02) while viewing the displayed
image to obtain the optimum picture sharpness. Turning the
control clockwise increases peaking and turning it
counterclockwise decreases peaking.
Mounting
The mountable transmitter (VTT001 MAAP) and mountable
receiver (VTR001 MAAP) may be attached to a wall with either
a stud-mounted wall box or with a wall mounting bracket
(Extron part # 70-163-xx). Both installations require the double
spaced MAAP connector frame, such as the CPM101). The
transmitter/receiver module can also be attached to any Extron
MAAP device that accepts a double spaced A/V connector
panel, or the modules may be rack mounted. The AAP versions
of the transmitter and receiver mount to Extron AAP frames
(see “Other accessories” in the appendix).
Preparing the wall box
For wall and furniture mounting installations, the installation
site must be deep enough for both the wall box and the cables.
The box should be at least 2.5" (6.4 cm) deep. Install cables into
the wall, furniture, or conduits before installing a wall box or
bracket.
2-10
1.
Place the wall box or mounting bracket against the
installation surface, and mark the guidelines for the
opening on the wall or furniture.
2.
Cut out the material from the marked area.
3.
Insert the wall box/bracket to check the opening’s size and
fit. Enlarge or smooth the edges of the opening if needed.
4.
If using a wall box, feed cables through the wall box’s
punch-out holes, and secure them with cable clamps to
provide strain relief.
5.
Exposed cable shields (braids or foil) are potential sources
of short circuits. Trim back and/or insulate shields with
heat shrink.
VTT001 and VTR001 • Installation
Screw
Braided Shield
Metal Wall Box
Cable Clamp
Installation Cable
Foil Shield
Figure 2-6 — Grounding outer braided and foil shields
To prevent short circuits, the outer foil shield can be
cut back to the point where the cable exits the cable
clamp. Both braided and foil shields should be
connected to an equipment ground at the other end
of the cable.
6.
Wall Stud
Installation Cable
Insert the wall box or wall bracket into the opening, and
attach it to the wall, stud, or furniture, leaving the front
edge flush with the outer wall or furniture surface.
Wall Stud
Installation Cable
Cable Clamp
Cable Clamp
Screws or Nails
Screws or Nails
Figure 2-7 — Attaching a wall box to a wall stud
VTT001 and VTR001 • Installation
2-11
Installation, cont’d
To attach a wall box to wood, use four #8 or #10 screws or
10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw
threads must penetrate the wood.
To attach a wall box to metal, use four #8 or #10 self-tapping
sheet metal screws or machine bolts with matching nuts.
7.
Mount the module(s) onto a faceplate or frame, then cable
and test the transmitter/receiver module(s) before
fastening it into the wall box or bracket. The cables are
inaccessible after installation.
Wall box mounting
1.
Attach the transmitter/receiver module(s) to the
mounting frame with the included #4-40 screws.
2.
Attach all power and video cables to the rear of the
transmitter/receiver. Power on the transmitter/receiver
now if the external power supply cannot be accessed once
the transmitter/receiver is mounted.
3.
Attach the mounting frame (with the attached
transmitter/receiver module(s)) to the wall box, using the
two included mounting screws.
Wall opening
flush with
edge of box
WER
PO
VT
T0
01
M AA
P
O
VIDE
T
INPU
VT
T 00
1
MA
AP
Extron
CPM101
Mounting Frame
Figure 2-8 — Attaching the mounting frame to a wall
box
2-12
4.
Connect the video input and output devices to the front
faceplates of the transmitter and receiver, respectively.
5.
Power on all devices.
VTT001 and VTR001 • Installation
Wall bracket mounting
1.
Attach the transmitter/receiver module(s) to the
mounting frame with the included #4-40 screws.
2.
Attach all power and video cables to the rear of the
transmitter/receiver. Power on the transmitter/receiver
now if the external power supply cannot be accessed once
the transmitter/receiver is mounted.
3.
Attach the mounting frame (with the attached
transmitter/receiver module(s)) to the mounting bracket
using the two included mounting screws.
Backing Clip
Extron
70-163-xx
Wall Mounting Bracket
R
WE
PO
V
0
TT
01
MA
AP
U
INP
T
VT
Extron
T0
01
MA
AP
Extron
VTT001 MAAP
Twisted Pair
Transmitter
CPM101
Mounting Frame
Figure 2-9 — Attaching the mounting frame to the
wall mounting bracket
VTT001 and VTR001 • Installation
2-13
Installation, cont’d
4.
Attach the video input and output devices to the front
faceplates of the transmitter and receiver, respectively.
5.
Power on all devices.
AAP mounting
The AAP versions of the VTT001 (VTT001 AAP) and VTR001
(VTR001 AAP) are mounted to the Extron AAP panel by
inserting the two AAP studs through the panel mounting holes
and attaching the nuts. See the following illustration.
Cable
Clamp
AAP 102
Cable
AA
P 10
2
UT
INP
01
T0
VT
#4-40 Nut w/ Captive
Washer
P
AA
VTT001 AAP
Figure 2-10 — Attaching a VTT001 AAP to an Extron
AAP frame
UL rack mounting guidelines
The following Underwriters Laboratories (UL) guidelines
pertain to the safe installation of the device in a rack.
2-14
1.
Elevated operating ambient temperature — If installed in
a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be
greater than room ambient temperature. Therefore,
install the unit in an environment compatible with the
maximum ambient temperature (Tma = +122 °F, +50 °C)
specified by Extron.
2.
Reduced air flow — Install the equipment in a rack so that
the amount of air flow required for safe operation of the
equipment is not compromised.
VTT001 and VTR001 • Installation
3.
Mechanical loading — Mount the equipment in the rack
so that a hazardous condition is not achieved due to
uneven mechanical loading.
4.
Circuit overloading — Connect the equipment to the
supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this
concern.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (e.g. use of power strips).
Rack mounting
Various 1U rack space frames accommodate the VTT001 MAAP,
VTT001 AAP, VTR001 MAAP, and VTR001 AAP modules. The
CPM133 is a one-third rack width frame that can be mounted to
the IN9080 rack mount shelf. The CPM112R, shown in figure 211, is a full rack width frame that holds six double sized
modules.
Depending on the A/V connector frame used, the transmitters/
receivers may be mounted to the rack with or without the rack
mount shelf.
1.
For mounting without a rack mount shelf, mount the
transmitter/receiver module(s) to the A/V connector
frame, then attach the frame directly to the rack. See
figure 2-11.
VTT001 and VTR001 • Installation
2-15
Installation, cont’d
WER
PO
er
itt
sm
T
CM Tr an
01 ir
INPU
O
T0 Pa
VT te d
VIDE
is
Tw
CPM112R
WER
PO
er
itt
sm
T
CM Tr an
01 ir
INPU
O
T0 Pa
VT te d
VIDE
is
Tw
A/V Connector Frame
WER
PO
er
itt
sm
T
CM Tr an
01 ir
INPU
O
T0 Pa
VT te d
VIDE
is
Tw
WER
PO
er
itt
sm
T
CM Tr an
01 ir
INPU
O
T0 Pa
VT te d
VIDE
is
Tw
WER
PO
er
itt
sm
T
CM Tr an
01 ir
INPU
O
T0 Pa
VT te d
VIDE
is
Tw
WER
PO
er
itt
sm
T
CM Tr an
01 ir
INPU
O
T0 Pa
VT te d
VIDE
is
Tw
(4) #4 - 40
Screws
Figure 2-11 — CPM112R A/V connector frame mounted
directly to a rack
For mounting the VTT001 MAAP/VTR001 MAAP to a
rack mount shelf, mount the transmitter/receiver
module(s) to the A/V connector frame, then attach the
frame to the shelf. See the example in figure 2-12.
2-16
VTT001 and VTR001 • Installation
RSB 129 (60-190-01)
Rack Mount Shelf
CPM133 (60-584-15) or
A/V Connector Frame
R
WE
PO
r
tte
mi
ns
T
CM Tra
01 ir
INPU
T0 Pa
EO
VT ed
VID
ist
Tw
(4) #4 - 40
Screws
(4) #6 Screws
Figure 2-12 — CPM133 A/V connector frame mounted
to a rack shelf
2.
Attach all power and video cables to the rear of the
transmitter/receiver. Power on the transmitter/receiver
now if the external power supply cannot be accessed once
the transmitter/receiver is mounted.
3.
Attach the video input and output devices to the front
faceplates of the transmitter and receiver, respectively.
Power on all devices.
VTT001 and VTR001 • Installation
2-17
Installation, cont’d
For mounting the VTT001 AAP/ VTR001 AAP to a rack, mount
the AAP module(s) to the Extron AAP frame, then attach the
frame to the rack. See the example in figure 2-13.
#10-32 Screw/
Nylon Captive
Cap Washer
AA
P 30
1
#4-40 Nut with
Captive Washer
UT
INP
01
T0
VT
P
AA
VTT001 AAP
Twisted Pair Transmitter
AAP 301
Architectural Frame
Figure 2-13 — Extron AAP 301 frame mounted directly
to a rack
2-18
VTT001 and VTR001 • Installation
VTT001/VTR001
A
Appendix
Reference Information
Specifications
Parts List
Reference Information,
cont’d
Reference
Information
Specifications
Video
Number/signal type ................... 1 set of proprietary analog signals
Connectors ................................... 1 RJ-45 female jack or 1 RJ-45 female jack
on a 3" (7.6 cm) pigtail
Video input
Number/signal type
VTT001 series ................... RGBHV, RGBS
VTR001 series ................... 1 set of proprietary analog signals from a
VTT001 model
Connectors
VTT001 series ................... (1) 15-pin HD female
VTR001 .............................. 1 RJ-45 female jack
VTR001 MAAP/AAP ...... 1 RJ-45 female jack on a 3" (7.6 cm) pigtail
Nominal level ............................... 0.7 Vp-p for RGB
Minimum/maximum levels ....... Analog: 0.3 V to 1.45 Vp-p with no offset
at unity gain
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 130 kHz
Vertical frequency ....................... 30 Hz to 150 Hz
Video output
Number/signal type
VTT001 series ...................
VTR001 series ...................
Connectors
VTT001 ..............................
VTT001 MAAP/AAP .......
VTR001 series ...................
Nominal level ...............................
Minimum/maximum levels .......
Impedance ....................................
Maximum resolution ...................
N
A-2
1 set of proprietary analog signals
RGBHV, RGBS
1 RJ-45 female jack
1 RJ-45 female on a 3" (7.6 cm) pigtail
(1) 15-pin HD female
0.7 V p-p for RGB
0.3 V to 1.45 Vp-p
75 ohms
1600x1200 or 1080p RGBHV
Refer to the this manual for the maximum distances recommended
for specific resolutions.
1080p component video is not supported.
VTT001 and VTR001 • Reference Information
Sync
Input type
VTT001 series ................... RGBHV, RGBS
Output type
VTR001 series ................... RGBHV, RGBS
Input level ..................................... 2.0 V to 5.5 Vp-p with ±0.2 VDC offset
max.
Output level .................................. 3.0 V to 4.0 Vp-p
Input impedance .......................... Hi-Z
Output impedance ....................... 75 ohms
Max. propagation delay .............. 580 ns
Max. rise/fall time ....................... 45 ns
Polarity .......................................... Negative
General
Recommended cable type .......... CAT 5/5e/6
Power ............................................ Supplied by an external power supply
External power supply ................ 100 VAC to 240 VAC, 50-60 Hz, external;
to 9 to 12 VDC, 2 A, regulated
Power input requirements ......... 12 VDC, 0.1 A for VTT
12VDC, 0.15 A for VTR
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling .......................................... Convection, no vents
Rack mount .................................. Yes, also furniture and wall mountable
with optional mounting hardware
Enclosure type .............................. Metal
Enclosure dimensions
VTT001/VTR001 MAAP
Faceplate ................... 1.4" H x 2.2" W x <0.1" D (3.5 cm H x 5.6 cm
W x 0.1 cm D)
(double space high MAAP plate)
VTT001/VTR001 AAP
Faceplate ................... 1.4" H x 3.5" W x 0.1” D (3.5 cm H x 8.9 cm
W x 0.3 cm D)
(double space high AAP plate)
VTT001 series
Device ........................ 1.4" H x 1.4" W x 1.4" D (3.5 cm H x 3.5 cm
W x 3.5 cm D)
(Depth excludes connectors.)
VTT001 and VTR001 • Reference Information
A-3
Reference Information, cont’d
VTR001 series
Device ........................ 1.4" H x 1.4" W x 1.75" D (3.5 cm H x 3.5 cm
W x 4.4 cm D)
(Depth excludes connectors.)
Product weight ............................. 1.0 lbs (0.5 kg)
Shipping weight ........................... 3 lbs (2 kg)
Vibration ....................................... ISTA 1A in carton (International Safe
Transit Association)
Regulatory compliance
Safety ................................. CE, c-UL, UL
EMI/EMC ......................... CE, C-tick, FCC Class A, ICES, VCCI
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
N
All nominal levels are at ±10%.
N
Specifications are subject to change without notice.
A-4
VTT001 and VTR001 • Reference Information
Parts List
VTT001 MAAP and VTR001 MAAP*
Description
Part number
VTT001 MAAP wall
VTT001 MAAP wall
VTR001 MAAP wall
VTR001 MAAP wall
mount
mount
mount
mount
transmitter - black
transmitter - white
receiver - black
receiver - white
70-284-11
70-284-21
70-285-11
70-285-21
* The MAAP models mount into MAAP (mini AAP) panels.
VTT001 and VTR001 tabletop
Description
VTT001 tabletop transmitter - black
VTR001 tabletop receiver - black
Part number
60-581-01
60-582-01
VTT001 AAP and VTR001 AAP**
Description
VTT001 AAP
VTT001 AAP
VTR001 AAP
VTR001 AAP
(black)
(white)
(black)
(white)
Part number
70-258-11
70-258-21
70-259-11
70-259-21
** The AAP versions of the VTT/VTR devices can be mounted in the
Extron AAP panels listed under “Other accessories” in this
chapter.
Included parts
Description
Part number
Power supply: universal
12 VDC, 2.0 A
Sharpness adjustment tool
VTT/VTR User’s Manual
VTT001 and VTR001 • Reference Information
A-5
Reference Information, cont’d
Skew-Free™ A/V UTP cables***
Description
Part number
UTP23SF-4/1000 1000’ bulk (non-plenum)
UTP23SF-4P/1000 1000’ bulk (plenum)
UTP23SF-4P/25 25’ preterminated (plenum)
UTP23SF-4P/35 35’ preterminated (plenum)
UTP23SF-4P/50 50’ preterminated (plenum)
UTP23SF-4P/75 75’ preterminated (plenum)
UTP23SF-4/12 12’ preterm. (non-plenum)
UTP23SF-4/25 25’ preterm. (non-plenum)
UTP23SF-4/50 50’ preterm. (non-plenum)
UTP23SF-4/100 100’ preterm. (non-plenum)
22-141-03
22-142-03
26-570-04
26-570-05
26-570-06
26-570-07
26-569-03
26-569-04
26-569-06
26-569-08
*** Other cable lengths are available.
Other accessories
Description
CPM101 MAAP plate, one-gang (black, white)
CPM112R MAAP rack-mount connector panel
CPM133 one-third rack width panel
RSB 129 rack mount shelf
AAP 102 frame (black)
AAP 102 frame (white)
AAP 104 frame (black)
AAP 104 frame (white)
AAP 106 frame (black)
AAP 106 frame (white)
AAP 201 frame - half rack width, 1U (black)
AAP 202 frame - half rack width, 2U (black)
AAP 301 frame - full rack width, 1U (black)
AAP 302 frame - full rack width, 1U (black)
A-6
Part number
60-583-11, -21
60-584-12
60-584-15
60-190-01
60-300-02
60-300-03
60-301-02
60-301-03
60-531-02
60-531-03
60-302-02
60-303-02
60-632-02
60-633-02
VTT001 and VTR001 • Reference Information
VTT001 and VTR001 • Reference Information
A-7
Reference Information, cont’d
A-8
VTT001 and VTR001 • Reference Information
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Download PDF