Windsor | ADMIRAL ADM8IE - 10080030 | Operating instructions | Windsor ADMIRAL ADM8IE - 10080030 Operating instructions

CARPET EXTRACTOR
Operating Instructions
MODEL:
ADM8
10080170
Read these instructions before operating the machine
Order Parts Here:
RR
86038320 03/16/07
PRV NO. 98628
www.ivie-ent.com/parts
Ph:(918)254-5161
MACHINE DATA LOG/OVERVIEW
MODEL _______________________________________
DATE OF PURCHASE __________________________
SERIAL NUMBER ______________________________
SALES REPRESENTATIVE # _____________________
DEALER NAME ________________________________
OPERATIONS GUIDE NUMBER ___________________
PUBLISHED __________________________________________
YOUR DEALER
Name: __________________________________________________________________________________________________
Address: _______________________________________________________________________________________________
For the name and address of your dealer contact: Windsor Industries
Phone Number: _________________________________________________________________________________________
1
ADMIRAL 86038230 03/16/07
TABLE OF CONTENTS
Machine Data Log/Overview................................1
Table of Contents.................................................2
HOW TO USE THIS MANUAL
How to use this Manual........................................1-1
SAFETY
Important Safety Instructions ...............................2-1
Hazard Intensity Level..........................................2-2
Grounding Instructions .........................................2-3
OPERATIONS
Technical Specifications.......................................3-1
Controls/Component Location .............................3-2
Filling Operation. ..................................................3-5
Operations............................................................3-7
Cleaning Procedure. ............................................3-8
Accessory Tool Usage. ...................................... 3-10
MAINTENANCE
Periodic Maintenance...........................................4-1
Daily/ Regular Maintenance. ................................4-2
Vacuum Motor Replacement ...............................4-3
Belt Replacement.................................................4-4
Solution Pump Replacement................................4-5
Wiring Diagram. ...................................................4-6
Troubleshooting Chart..........................................4-7
GROUP PARTS LIST
Frame Assembly. ............................................... 5-1
Brush Assembly. ................................................ 5-3
Pump Assembly. ................................................ 5-5
Vacuum Shoe Assembly. ................................... 5-7
Control Panel Assembly..................................... 5-9
Solution Tank Assembly..................................... 5-11
Recovery Tank Assembly. ................................. 5-13
Suggested Spare Parts/Notes ........................... 5-15
ADMIRAL 86038230 03/16/07
2
HOW TO USE THIS MANUAL
This manual contains the following sections:
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
MAINTENANCE
PARTS LIST
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
Parts may be ordered from authorized dealers.
When placing an order for parts, the machine model
and machine serial number are important. Refer to
the MACHINE DATA box which is filled out during
the installation of your machine. The MACHINE
DATA box is located on the inside of the front cover
of this manual.
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards is identified that could
result in product or personal injury, or severe injury
resulting in death.
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
-
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
-
SALES REPRESENTATIVE # ___________________
-
DEALER NAME ______________________________
OPERATIONS GUIDE NUMBER __________________
-
PUBLISHED ________________________________
The model and serial number of your machine is on
the bottom back-end of the machine.
Periodic
Daily/Regular
Troubleshooting
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
PRV NO. – reference number.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine.
The main illustration shows the most
current design of the machine. The
boxed illustrations show older designs.
If column has an asterisk (*), call
manufacturer for serial number.
NOTES – column for information not
noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The 98# on the lower left corner of the front
cover is the part number for this manual.
1-1
ADMIRAL 86038230 03/16/07
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
! WARNING:
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or
service.
Use only indoors. Do not use outdoors or expose to rain.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the
machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp
edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near
flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops
and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
ADMIRAL 86038230 03/16/07
2-1
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate
all safety devices on the machine. Please take the necessary steps to train the machine operating
personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use manufacturer approved replacement parts.
2-2
ADMIRAL 86038230 03/16/07
GROUNDING INSTRUCTIONS
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
ELECTRICAL:
In the USA this machine operates on a standard 15
amp 115V, 60 hz, A.C. power circuit . The amp, hertz,
and voltage are listed on the data label found on each
machine.
Using voltages above or below those
indicated on the data label will cause serious damage
to the motors.
PROPER GROUNDING
Grounding Pin
Grounded
Outlet
Fig. A
Metal Screw
Adaptor
Grounded Outlet Box
Fig. B
Tab For Grounding Screw
Adaptor
Fig. C
GROUNDING INSTRUCTIONS:
This appliance must be grounded.
If it should
malfunction or break down, grounding provides a path
of least resistance for electric current to reduce the risk
of electric shock. This appliance is equipped with a
cord having an equipment-grounding conductor and
grounding plug. The plug must be inserted into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
This appliance is for use on a nominal 115-volt circuit,
and has a grounded plug that
looks like the plug in “Fig. A”. A temporary adaptor
that looks like the adaptor in “Fig . C” may be used to
connect this plug to a 2-pole receptacle as shown in
“Fig. B”, if a properly grounded outlet is not available.
The temporary adaptor should be used only until a
properly grounded outlet (Fig. A) can be installed by a
qualified electrician. The green colored rigid ear, lug,
or the like extending from the adaptor must be
connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adaptor is
used, it must be held in place by a metal screw.
NOTE: In Canada, the use of a temporary adaptor is not
permitted by the Canadian Electrical Code
! WARNING:
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service person if you are
in doubt as to whether the outlet is properly grounded.
Do not modify the plug provided with the appliance - if
it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
ADMIRAL 86038230 03/16/07
2-3
TECHNICAL SPECIFICATIONS
POWER TYPE
GENERAL DIMENSIONS/WEIGHT
ELECTRICAL: 115 V, 15 A, 60 HZ
Vacuum shoe: 17” (43.18 cm) cast
aluminum with spring loaded down pressure
ELECTRIC VACUUM MOTOR: (1) –3 stage, 1 hp, 99 cfm
(2.80 cubic meters/min.) Waterlift –117” (297cm)
WHEELS: (2) 10” dia. (25 cm) wheels by 2”
BRUSH: (1) 15” (38.1 cm.)
WEIGHT: 92 lbs. (42 kg)
SOLUTION PUMP: 100 PSI, diaphragm style, internal
bypass
LENGTH: 35” (89 cm)
HEIGHT: 42” (107 cm)
SOLUTION CAPACITY: 8 gallons (30.3 ltr)
WIDTH: 18.5” (47 cm)
RECOVERY CAPACITY: 8 gallons (30.3 ltr)
SOLUTION SPRAY: 2 quick change jets.
BRUSH SPEED: 1000 rpm
POWER CABLE: 50’ (12.7 m) (14 gauge)
42”
(107cm)
35”
(89cm)
3-1
18.5”
(47cm)
ADMIRAL 86038230 03/16/07
CONTROLS/COMPONENT LOCATIONS
8
9
5
4
1. Main Handle. Used to pull and maneuver
machine.
6
2. Handle Adjustment. Used to adjust height
of handle.
3. Electrical Cord.
4. Solution Switch. Turns on pump.
Continuous position (bottom) activates
electro-valve to dispense solution to floor
through jets. Intermittent position (up)
requires operator to depress 1 of 3 trigger
switches to dispense solution. Center
position is off.
7
5. Brush Motor Switch. Turns on brush
motor.
6. Vacuum Motor Switch. Turns on vacuum
motor.
7. Trigger Switches. Activates electro-valve
to dispense solution to floor through jets
when solution switch is in the intermittent
position.
1
3
8. Brush Motor Circuit Breaker. 6 amp.
Breaker protecting brush motor.
9. Vacuum Motor Circuit Breaker. 15 amp.
Breaker protecting vacuum motor.
10
2
11
10. Recovery Dump Hose. Facilitates draining
dirty cleaning solution.
11. Solution Dump Hose. Facilitates draining
excess cleaning solution from solution tank.
ADMIRAL 86038230 03/16/07
3-2
CONTROLS/COMPONENT LOCATIONS
1. Solution Accessory Tool Hookup. Used for
various auxiliary cleaning tools.
2. Vacuum Hose Door. Used to connect various
auxiliary 1 ½ inch cleaning tool vacuum hoses.
11
3. Brush Height Adjustment. Used to regulate
brush height from storage position to various
carpet heights.
4. Recovery Tank. Used to collect dirty cleaning
solution.
10
5. Solution Tank. Used to hold cleaning solution.
6. Recovery Tank Dome.
7. Vacuum Shoe.
1
8. Brush Housing.
9. Front Lifting Handle.
10. Cleaning Solution Filter.
11. Solution Tank Fill Hose.
9
3
2
6
4
5
7
8
3-3
ADMIRAL 86038230 03/16/07
CONTROLS/COMPONENT LOCATIONS
1. Solution Intake Cover.
2. Vacuum Intake Cover.
3. Float Shut-Off.
4. Clean-Out Opening.
5. Pour Spout.
6. Lift Handle.
6
1
2
4
6
5
3
ADMIRAL 86038230 03/16/07
3-4
FILLING OPERATIONS
STEP
1
RECOVERY TANK
Remove recovery
tank
SOLUTION
TANK
STEP
2
Add water
or
8 gal.
(30.3 ltr.)
140°F (60°C)
FILL LINE
STEP
3
FILLING THE ADMIRAL
NOTE: Use clean bucket of water to fill solution tank
8 – 16oz.
(237ml – 473ml)
Add cleaning
chemical
Do not put defoamer, solvents, spotter or
prespray chemicals in the solution tank.
Do not allow water to spill into vacuum motor inlet.
Dry spillage from top of solution tank before
replacing recovery tank.
CHEMICALS
Suitable Chemicals
Alkalis
Detergents
Hydroxides
Soaps
Vinegar
3-5
Non-Compatible Chemicals
Aldehydes
Aromatic Hydrocarbons
SP Butyls
Carbon Tetrachloride
Clorox*
Chlorinated Bleaches
Chlorinated Hydrocarbons
Lysol*
Methyl Ethel Ketone (MEK)
Perchorethylene (perc)
Phenolics
Trichlorethylene
D-Limonene
STEP
4
ADMIRAL 86038230 03/16/07
Replace recovery
tank
OPERATIONS
STEP
1
Remove electrical cord and literature from
recovery tank. Fill solution tank (see filling
instructions page 3-5).
STEP
2
Plug cord into grounded outlet. Note: Be sure
dome is seated on recovery tank, and float
shut-off is installed correctly.
STEP
3
Adjust brush to proper setting. Note: For
good operation the brush must skim the
carpet. If circuit breaker trips raise brush to
prevent damage to motor or carpet.
1/8in
(3mm)
CORRECT
INCORRECT
STEP
4
SOLUTION
BRUSH
VACUUM
INT
ON
ON
Turn on brush and vacuum motor switches
(“ON”=“I”). Turn on solution switch for
continuous spray or set switch to intermittent
to allow use of trigger switches.
CONT
ADMIRAL 86038230 03/16/07
3-6
OPERATIONS
Adjust handle to comfortable operating
position. Tip machine back by main handle
to move to starting point.
STEP
5
Lower machine to floor.
STEP
6
Select continuous setting to start solution
STEP
spray or select intermittent setting to
7
enable use of trigger switches to start
solution spray.
The intermittent setting requires the
operator to hold any one of the three
trigger switches in the “on” position with the
fingers, and is typically used in small areas
where short cleaning passes are made.
The continuous setting allows the operator
to set the switch in the “on” position with
one touch, and is typically used in large
areas where long cleaning passes are
made.
3-7
ADMIRAL 86038230 03/16/07
INT
CONT
CLEANING PROCEDURE
STEP
1
1ft.
(30cm)
STEP
2
Release intermittent trigger switches or
turn off continuous setting on solution
switch approximately 1 foot before ending
cleaning pass.
STEP
3
Push down on handle to raise vacuum
shoe and brush before moving to the next
cleaning pass. Overlap brush contact
area approximately 1inch.
OFF
1in.
(25mm)
SOLUTION
INTAKE COVER
VACUUM
INTAKE COVER
Start at wall closest to power outlet. Pull
straight back without pushing down on
handle.
STEP During operation, observe the following: The
Admiral is equipped with clear internal covers to
4
facilitate operator viewing of dirty solution and
vacuum air flow.
During operation, observe the vacuum intake
cover. Large amounts of water or foam entering
the vacuum system can damage the vacuum
motor. If you notice either condition, shut down
the machine immediately. Empty recovery
tank and/or add defoamer to recovery tank.
ADMIRAL 86038230 03/16/07
3-8
CLEANING PROCEDURE
Use right side of machine for cleaning
against walls.
STEP
5
After cleaning, turn off all controls, return
brush to storage position and carefully
unplug machine.
STEP
6
OFF
OFF
To speed drying, use a Windblower™ fan.
STEP
7
Empty recovery tank by releasing dump
hose. Use a hose with cold water to clean
out the recovery tank. Also drain solution
tank after each use.
STEP
8
OFF
RECOVERY
DRAIN
SOLUTION
DRAIN
3-9
ADMIRAL 86038230 03/16/07
ACCESSORY TOOL USAGE
STEP
APRV NO.
1
Use only one of the following acceptable
accessory tools.
HT – 86000610 PRV NO. 89227
DDH – 86000060 PRV NO. 89226
DH – 86031540 PRV NO. 39504
Pull back collar and insert over machine
mounted fitting, then release collar to lock
into place.
STEP
2
3
Turn on vacuum motor switch and set
solution switch to intermittent position.
Note: Be sure brush switch is in off position
and brush is in storage position.
STEP
Squeeze handle on accessory tool to begin
cleaning.
STEP
SOLUTION
BRUSH
INT
Lift door on front of vacuum shoe and insert
1 ½ inch hose cuff into hole.
VACUUM
ON
OFF
4
ADMIRAL 86038230 03/16/07
3-10
MAINTENANCE
SERVICE SCHEDULE
MAINTENANCE
Check machine for cord damage
Check recovery dome and gasket for
damage and cleanliness
Check brush – should be clean with no
lint or strings attached
Inspect vac shoe for blockage; remove
fibers with coat hanger, etc.
Check hoses for wear, blockages, or
damage
Check handles, switches, and knobs
for damage
Check vac motor intake filter and clean
Run one gallon of water through
system
Clean out recovery tank and check
float valve to make sure it moves freely
Clean out solution tank and remove
and clean vacuum intake screen
Clean outside of all tanks and check for
damage
Run vac motor for at least one minute
to allow motor to dry
Store with dome off tank to allow the
tank to dry
Check all bearings for noise
Check all gaskets for wear and leakage
Check vacuum intake screen for
damage; replace if necessary
Check pump pressure; observe spray
pattern and check with gauge if
necessary
Check and clean solution screen
Check belts for wear and replace as
necessary
Check brush for wear; ensure bristles
are not damaged
Check cables for fraying
Check the spray bar (manifold) for
damage; replace if broken or bent
Check condition of vac shoe and frame
for damage
Check overall performance of machine
Check vac motor carbon brushes
4-1
DAILY
*
WEEKLY
QUARTERLY
*
*
*
*
*
*
*
*
*
*
*
*
ADMIRAL 86038230 03/16/07
*
*
*
*
*
*
*
*
*
*
*
*
MAINTENANCE
PERIODIC MAINTENANCE
Twice a month, flush a white vinegar solution (One
quart vinegar to two gallons of water) or antibrowning solution (mixed as directed) through the
extractor. This will prevent build-up of alkaline
residue in the system. If spray jets become clogged,
remove the spray tips, wash them thoroughly, and
blow-dry.
NOTE: Do not use pins, wire, etc. to clean nozzles
as this could destroy spray pattern.
Periodically inspect all hoses, electrical cables and
connections on your machine. Frayed or cracked
hoses should be repaired or replaced to eliminate
vacuum or solution pressure loss. If the cable
insulation is broken or frayed, repair or replace it
immediately. Don’t take chances with electrical fire
or shock.
7. Remove lint and dirt build-up from brush and
housing.
NOTE: Brush removal.
A. To remove brush, grab and pull brush out
from end opposite drive belt (operator’s
right). Remove other end from brush driver.
B. To install brush, line up slots in brush core
with pin in driver on drive belt side
(operator’s left) and push brush onto driver.
Then snap bearing end (opposite end) of
brush into retaining clip.
8. Check cooling air screen (located on frame
behind left wheel) for lint or debris.
9. Check float and shut-off screen and clean as
necessary.
NOTE: Always store machine with brush in “Store”
position.
DAILY / REGULAR MAINTENANCE
Before making any adjustments or repairs to the
machine, disconnect the power cord from electrical
source.
1. Empty unused cleaning solution from the
solution tank.
2. Inspect and clean filter screen in solution tank.
3. Flush pumping system with 4 or 7 liters of clean,
hot water.
4. After each use, rinse tank with fresh water.
Periodically inspect the recovery tank and
decontaminate if necessary, using a Hospital
Grade Virucide or a 1-10 bleach to water
solution. Waste water should be disposed of
properly.
5. Check for and remove any lint or debris around
vac shoe.
6. Check spray jets for full spray pattern.
ADMIRAL 86038230 03/16/07
4-2
MAINTENANCE
! WARNING:
ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE
FOLLOWING REPAIRS.
VACUUM MOTOR REPLACEMENT
Vacuum Motor Carbon Brushes Replacement (Ametek)
1. Turn off all switches and unplug machine.
End Cap
2. Remove recovery tank.
3. Remove the (2) screws that fasten the solution tank to
the frame, and tilt tank back to expose the inside of the
frame.
Carbon
Brushes
WARNING: The green
ground wire must be
attached for safe operation.
See wiring diagram.
4. Locate the vacuum motor wires and disconnect at the
connector. Close the solution tank.
5. Remove the (6) screws holding the vacuum motor cover
(p/n 27809) to the solution tank.
6. Remove the vacuum motor.
Note: When replacing carbon brushes loosen wire terminal
BEFORE removing screws on bracket.
Wire
Terminal
7. Reverse process to install vacuum motor.
Vacuum Motor Carbon Brushes Replacement (Windsor)
End Cap
Carbon
Brushes
Note:
Place
stop in
groove.
WARNING: The green
ground wire must be
attached for safe operation.
See wiring diagram.
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Wire Terminal
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
3 [9.5mm]
8
3/8 (9.5mm)
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
4-3
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
ADMIRAL 86038230 03/16/07
MAINTENANCE
! WARNING:
ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE
FOLLOWING REPAIRS.
BELT REPLACEMENT
1. Turn off all switches and unplug machine.
86249420
PRV NO. 62759
2. Remove recovery tank and brush.
3. Remove the (2) screws that fasten the solution tank to the
frame, and tilt tank back to expose the inside of the frame.
4. Loosen the (4) screws that hold the brush motor in place
and slide motor forward to release tension in belt.
5. Remove the (2) screws that fasten the vacuum shoe links
(p/n 05016) to the brush housing.
6. Remove the (3) screws that fasten the side plate (p/n
62759) to the brush housing to remove belt. NOTE: All
components associated with driving the brush will come out
with the side plate.
7. Reverse process to install belt.
ADMIRAL 86038230 03/16/07
86287330
PRV NO. 05016
4-4
MAINTENANCE
! WARNING:
ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM
THE FOLLOWING REPAIRS.
`
SOLUTION PUMP REPLACEMENT
1.
Turn off all switches and unplug the machine.
2.
Remove recovery tank.
3.
Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame.
4.
Remove solution hoses from fittings in pump.
5.
Remove the (2) screws that fasten the pump to the frame.
6. Reverse process to install pump.
86161980
PRV NO. 250-67
Switch Asm
PUMP REPLACEMENT KITS SHURFLO 100 PSI 86026390 PRV NO. (65201)
Pump Head Replacement
8251040
PRV NO. 65187
Bypass Valve Asm
86258830
PRV NO. 84161
Diaphragm
86235100
PRV NO. 29206
PUMP REPLACEMENT PARTS FOR FLOJET 100 PSI PRIOR TO SERIAL # *
Pump Head
86251090
PRV NO. 65204
Valve Asm
86258860
PRV NO. 84166
4-5
Motor
86247360
PRV NO. 53245
Diaphragm
86235120
PRV NO. 29219
ADMIRAL 86038230 03/16/07
WIRING DIAGRAM
86268290
PRV NO. 88229
86268460
PRV NO. 88333
86268430
PRV NO. 88323
86266720
PRV NO. 880043
86238840
PRV NO. 41356
8638830
PRV NO. 41355
86266890
PRV NO. 88655
86238820
PRV NO. 41351
ADMIRAL 86038230 03/16/07
4-6
TROUBLESHOOTING CHART
PROBLEM
No Power, Nothing
Runs
Vacuum Motor Will Not
Run
Vacuum Motor Runs
But
Suction Is Poor
Poor Or No Water Flow
(Carpet Is Streaky)
CAUSE
Is the cord plugged in.
Circuit breaker tripped in building.
Faulty switch.
Faulty power cord or pigtail.
Vacuum circuit breaker tripped.
Faulty main vacuum switch.
Loose wiring.
Faulty vac motor.
Carbon brushes worn.
Debris lodged in vac shoe.
Dome gasket defective or missing.
.Vacuum hose cracked or hose cuff loose.
Recovery tank full / float ball stuck in the
up position.
.Main pump switch off.
Jets clogged or missing.
Solution filter clogged.
Brush Does Not Spin
4-7
Faulty solenoid.
Brush switch off.
Brush circuit breaker tripped.
Brush belt broken.
Faulty brush motor.
SOLUTION
Plug in cord.
Reset breaker.
Call for service.
Call for service.
Reset breaker.
Call for service.
Call for service.
Call for service.
See “Brush Replacement” in
maintenance section.
Remove debris from vac shoe.
Replace as necessary.
Replace or repair as necessary.
Turn off vac motor. Drain and rinse
recovery tank.
Turn on.
Clean using a vinegar /water solution or
replace.
Drain solution tank and clean solution
filter.
Call for service.
Turn on brush switch.
Reset circuit breaker.
Replace as necessary.
Call for service.
ADMIRAL 86038230 03/16/07
NOTES:
ADMIRAL 86038230 03/16/07
4-8
FRAME ASSEMBLY
30
7
19
18
15
(SEE PG. 5-11)
A
21
B
12
33
11
28
10
3
34
31
6
C
5
(SEE PG. 5-9)
22
26
9
32
2
25
27
16
29
8
13
20
5-1
14
4
24
ADMIRAL 86038230 03/16/07
FRAME ASSEMBLY
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PART NO.
86003620
86004340
86001660
86238820
86239610
86026150
86005640
86005810
86198530
86249430
86006020
86250130
86250140
86006580
86273980
86010630
86010660
86010650
86006550
86256190
86259960
86259960
86066230
86134490
86253090
86002370
86233140
86274760
86006530
86272160
86276610
86005710
PRV NO.
QTY
DESCRIPTION
OPEN
34341
39528
41236
41351
41354
53640
57030
57245
99809
62761
64099
66282
66288
70085
70066
OPEN
87013
87025
87018
70074
73197
OPEN
89506
03107
99667
73943
20035
20041
70271
70057
66052
70697
57105
1
1
2
1
1
1
2
3
2
1
1
6
2
2
2
2
2
2
2
1
2
1
10”
1
1
1
2
2
1
1
3
FRAME, CLP FAMILY
HOSE ASM, 1.5 BLK VAC X 15.5
HUBCAP, 5/8" SHAFT
HARNESS, MAIN, CLP/ADM
HINGE, TANK TO FRAME
MOTOR ASM, BRUSH CLP FAMILY
NUT, 10-32 HEX NYLOCK
NUT, 1/4-20 HEX NYLOCK SS
FOAM TAPE, 1/8 THK X 3/4 1SDA
PLATE, BRUSH MTR CLAMP
PULLEY, 1.4 OD, 6GR, MICRO-V
PLUG, HOLE, .375" BLK
PLUG, 9/16 OD BLK NYLON
SCR, 1/4-20 X 1/2 PPHMS SS
SCR, 10-32 X 3/4 PPHMS
WASHER, 1/4 ID X 5/8 OD SS
WASHER, 1/4 LOCK EXT STAR SS
WASHER, #10 X 9/16 OD
SET SCR, 10-32 X 1/4 KCP
STRAIN RELIEF, 90 DEGREE
WHEEL, 1-15/16 X 10” HOOSIER
AXLE, 5/8 X 17.06L
HEAT SHRINK, 3/4 ID UL/CSA
SEAL, FRAME/TANK
CLAMP, 7/16 DIA NYLON UL
CLAMP, 2.0" WORM GEAR
SCR, 1/4-20 X 1/2 HHCS PLTD
SCR, 1/4-20 X 1 PPHMS SS
PIN, ROLL 1/8” X 1.0”L
SCR, 1/4-20 X 1.25 PPHMS SS
NUT, 1/4-20 HEX W/ STAR WASHER
ADMIRAL 86038230 03/16/07
SERIAL NO.
FROM
NOTES:
1000046197
5-2
BRUSH ASSEMBLY
31
15
25
11
7
25
29
30
8
16
12
26
24
38
18
16
30
39
10
22
34
4
44
45
36
40
37
33
47
41
26
32
17
28 35
3
43
21
13
42
27
6
1
19
14
17
23
20
30
25
29
25
46
3
9
2
5
5-3
ADMIRAL 86038230 03/16/07
BRUSH ASSEMBLY
REF
PART NO.
PART NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
86000730
86227100
86000900
86001100
86001140
86001300
86001310
86003620
86004060
86004470
86004980
86093080
86005110
86005120
86005130
86005640
86008580
86249410
86249420
86005930
86250680
86006220
86006430
86006510
86006590
86006650
86006700
86275530
86010640
86010650
86007030
86230620
86251710
86003070
86003370
86278130
86272770
86272510
86008650
86008160
86006030
86003390
86001140
86227150
86228890
86028010
86004750
03110
04084
09019
11045
12514
140343
140351
34341
36192
41345
50998
51311
51312
51314
51317
57030
57271
62758
62759
62762
64098
66192
67411
70043
70088
70177
70232
70497
87016
87018
70675
12524
67467
27805
29157
70737
67094
66310
80604
73966
64102
29208
12514
05158
09137
47383
47416
1
1
2
1
1
1
1
REF
2
1
1
1
1
2
1
4
2
1
1
2
1
1
1
2
8
7
2
2
4
6
4
1
1
1
1
1
1
2
2
1
1
1
1
1
2
1
REF
AXLE, ROLLER
ADAPTER, BRUSH BRG.
BEARING, 1.125ODX.500IDX.375
BELT, 180J6 MICRO-V
BRUSH, 15L X 3.38OD
BRKT, BRUSH PULLEY
BRKT, BRUSH HEIGHT
FRAME, CLP FAMILY
GUARD, THREAD
HOUSING, BRUSH 15"
LABEL, BRUSH HEIGHT
LINKAGE, ASM, BRUSH HEIGHT
LINKAGE ASM, ROLLER SUPPORT
LINK, ROLLER, FRONT
LEVER, HEIGHT ADJUSTMENT
NUT, 10-32 HEX NYLOCK
NUT, 3/8 DIA CAP, TYPE PUSH PLT
PLATE, BRUSH HOUSING RH
PLATE, BRUSH HOUSING LH
PLATE, AXLE RETAINER
PULLEY, 2.2 OD, 6GR, MICRO-V
PIN, ROLL 1/4 X 1.25L
ROLLER, 1.9 DIA X 10.5 LG
SCR, 10-32 X 5/8 PFHMS
SCR, 10-32 X 1/2 PPHMS SS DL
SCR, 10-32 X 1/2 FHMS SS
SCR, 10-32 X 3/8 FHMS SS
SCR, #10-24 X 1/2 SHCS
WASHER, #10 LOCK EXT STAR SS
WASHER, #10 X 9/16 OD
SCR, 1/4-20 X.5/8 THMS PLTD NP
BRUSH, 15 L X 3.38 OD G2
RING, TOLERANCE 7/8 ID X 1/2 W
CLIP, BEARING
DRIVER, BRUSH
SHLDR BOLT, 3/8 OD X 3/8 L SS NP
RING, 1/2 EXT. SNAP
PIN, CLEVIS 1/4 X 1/2 PLTD
COTTER, 1/4" RING
SPACER, .81ID X 1.06OD, ALUM
PULLEY ASM, BRUSH
DRIVER ASM, BRUSH
BRUSH ASM, 15 IN
ADAPTER, BRUSH BRG. DIE CAST
BEARING R6 3/8 ID
BRUSH BEARING ASM
KIT, BRNG/ADPTR EXTRCTR
ADMIRAL 86038230 03/16/07
SERIAL NO.
FROM
NOTES:
1000060649
1000060649
1000060649
1000060649
1000060649
5-4
PUMP ASSEMBLY
14
3
20
8
13
4
10
16
9
2
16
21
23
18 1
12
19
15
20
11
17
7
25
26
28
D
(SEE PG. 5-11)
26
24
27
5-5
ADMIRAL 86038230 03/16/07
6
5
PUMP ASSEMBLY
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
86002470
86002480
86003470
86003490
86004570
86241680
86005640
86026390
86250140
86274410
86273750
86003640
86008360
86026940
86010810
86010650
86010820
86005590
86005580
86003500
86274290
22072
22090
31072
31074
44067
44073
57030
65201
66288
70195
70011
34355
78419
84160
87191
87018
87192
56014
56012
31076
70162
880278
39529
39530
39531
73963
39591
1
2
1
1
2
2
2
1
2
2
2
1
1
1
2
4
2
1
1
2
2
1
1
1
3
1
1
86267400
86281890
86004350
86281900
86253020
86004400
DESCRIPTION
COUPLING, 1/4 ANCHOR W/1" HEX
CONNECTOR, 1/8FPT X 1/4 TUBEQC
ELBOW, SWIVEL, 1/4MPTX1/4TUBE
ELBOW, SWIVEL, 3/8MPTX3/8TUBEQC
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 9503
NUT, 10-32 HEX NYLOCK
PUMP ASM, 115V 100 PSI W/CONN
PLUG, 9/16 OD BLK NYLON
SCR, 10-32 X 1.25 PPHMS
SCR, 1/4-20 X 5/8 HHCS SS
FITTING, 1/4 TUBE,"Y", QC
TEE, 3/8 MPT X 3/8 TUBE, QC
VALVE ASM, SOLENOID CLP FAMILY
WASHER, 1/4"IDX1.0OD. FLAT SS
WASHER, #10 X 9/16 OD
WASHER, 7/16 X 3/4 X .19RUBBER
NIPPLE, 1/4 CLOSE
NIPPLE, 1/4 FPT QD
ELBOW, 1/4 MPT X 3/8 TUBE, QC
SCR, 10-32 X 3/8 PPHMS SS
OPEN
WIRE, 22" GRN/18 76011 X 76011
HOSE, 3/8 URETHANE X 29"
HOSE, 3/8 NYLON X 6"
HOSE, 1/4 URETHANE X 6"
SCREEN, INTAKE
HOSE, 3/8 ID NYL11 YLW X 29”
ADMIRAL 86038230 03/16/07
SERIAL NO.
FROM
NOTES:
1000167303
100046197
5-6
VACUUM SHOE ASSEMBLY
1
4
11
7
13
10
2
12
3
5
8
6
7
11
5-7
ADMIRAL 86038230 03/16/07
VACUUM SHOE ASSEMBLY
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
86227350
86234760
86005810
86006790
86275120
86006840
86008130
86010620
OPEN
86010630
86010700
86003780
86008120
05016
27674
57245
70351
70360
70390
73958
85039
87013
87074
35171
73955
4
1
4
2
4
4
8
1
4
8
1
2
DESCRIPTION
SERIAL NO.
FROM
NOTES:
ARM, VAC SHOE PARALLEL
COVER, ACCESSORY PORT
NUT, 1/4-20 HEX NYLOCK SS
SCR, 10-32 X 3/8 HHTR W/STAR
SCR, 1/4-20 X.75 PPHMS PHIL
SCR, 1/4-20 X 1 FHCS PLTD
SPACER, 3/8ODX.058WX.2814,CRS
VAC SHOE, 15"
WASHER, 1/4 ID X 5/8 OD SS
WASHER, WAVE 3/8ID X3/4D X.125
GASKET, ACCESSORY PORT
SPRING, EXT .38D X2.75L X.055W
ADMIRAL 86038230 03/16/07
5-8
CONTROL PANEL ASSEMBLY
18
39
4
10
37
22
44
33
3
16
29
28
11
45
38
46
23
2
41
1
40
31
7
8
21
27
15
9
24
42
20
6
12
30
35
C
34
(SEE PG. 5-1)
5
17
19
25
13
14
29
26
5-9
43
ADMIRAL 86038230 03/16/07
32
36
CONTROL PANEL ASSEMBLY
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
86001240
86001980
86230210
86002010
86233240
86234320
86003130
86003140
86076550
86004100
86004110
86004790
86246300
86246650
86005670
86081530
86264270
86007140
86087410
86256240
86008350
86245950
86005760
86005810
86272190
86227650
86006870
86006620
86006790
86274150
86006710
86005750
86010750
86198480
86238820
86234110
86272840
86256170
86007200
86006830
86005700
86010660
86010670
86002870
86232290
86245040
14020
14700
14832
14942
20084
23679
27823
27824
38283
38286
38287
48012
51039
51313
57040
62766
67073
72130
73180
73505
78418
50996
57116
57245
66068
03109
70406
70127
70351
70105
70235
57113
87100
27371
41351
23086
67147
73169
72162
70386
57104
87025
87029
27417
500017
50279
1
1
1
2
2
1
3
3
2
1
1
1
1
2
2
1
1
2
1
1
3
1
2
4
1
1
9
6
5
4
2
2
2
2
REF
1
1
1
1
1
3
1
2
1
1
1
TERMINAL BLOCK, 115V (3-4-3)
BREAKER, 15A 250VAC 50VDC
BREAKER, 6A VDE CIRCUIT
BOOT, 3/8 CIRCUIT BREAKER
CLAMP, HANDLE LOCK
CORD ASM, 14/3 X 22" YLW
CONTACT, ELECTRICAL, FLAT
CONTACT, ELECTRICAL, BENT
HANDLE, ADM8
HANDLE, CONTROL PANEL FRONT
HANDLE, CONTROL PANEL REAR
KNOB, 5/16-18 4 PRONG
LEVER, HANDLE CLAMP
LINK, HANDLE ADJ.
NUT, 1/2 NPT CONDUIT
PLATE, CONTROL PANEL, CLP/ADM
ROD, HANDLE LOCK
SWITCH, SPST 2-POSITION ROCKER
SPACER, .50 ODX.058WX9.84L CRS
STRAIN RELIEF, 1/2 NPT TRUMPET
TRIGGER, SWITCH
LABEL, CONTROL PANEL, CLP/ADM
NUT, 6-32 W/STAR WASHER PLTD
NUT, 1/4-20 HEX NYLOCK SS
PIN, ROLL 1/8" X 5/8"L
AXLE, HANDLE ADM8
SCR, #10 X 3/4 PPHST TYPE B
SCR, 6-32 X 1/4 PPHMS SS
SCR, 10-32 X 3/8 HHTR W/STAR
SCR, 1/4-20 X 1.75 PPHMS SS
SCR, 6-32 X 1.0 PH BLK NYLON
NUT, 5/16-18 HEX NYLOCK
WASHER, 3/8 ID INT.LOCK THIN
CLIP, POWER CORD
HARNESS, MAIN CLP/ADM
CORD SET,14/3 SJTW-A X 50' YLW
RING, 2" DIA SPLIT
STRAIN RELIEF, CORD HOOK
SWITCH, DPDT3-POSITION ROCKER
SCR, 10-32 X 1” PPHMS
NUT, 10-32 W/STAR WASHER PLTD
WASHER, 1/4 LOCK EXT STAR SS
WASHER, 5/16 FLAT SS
CORD, 99807 1/8 X 12"
CARD, INSTRUCTION ADM8
LABEL, GROUND SYMBOL
ADMIRAL 86038230 03/16/07
SERIAL NO.
FROM
NOTES:
5-10
SOLUTION TANK ASSEMBLY
6
13
3
16
7
12
12A
12B
10
20
15
7*
(SEE PG. 5-1)
30
A
11
19
14*
18
24*
8
9
17*
2
32
26
1
25
18
22*
4
B
28
(SEE PG. 5-1)
29
5-11
23*
21*
5*
31
ADMIRAL 86038230 03/16/07
16
27
D
(SEE PG. 5-5)
16
27
SOLUTION TANK ASSEMBLY
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
86233140
86233150
86003080
86003090
20041
20042
27809
27810
2
1
1
1
5
86235500
31081
1
6
86003790
35175
2
7
86003920
35231
2
8
9
10
11
12
86281880
86240090
86004340
86240980
86026880
39526
39527
39528
41348
53789
1
1
REF
1
1
12A
86135340
14258
-
12B
86135320
140687
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
86275690
86032260
86259060
86010650
86007970
86010630
86006580
86233260
86003950
86003960
86003970
86197940
86275120
86010660
86006600
86095840
86005810
86260690
86233150
86197920
70525
75259
85037
87018
73864
87013
70085
20092
35236
35237
35238
40027
70360
87025
70114
89183
57245
02130
20042
40023
6
1
1
10
1
5
3
1
1
1
1
1
2
2
4
1
2
1
1
1
SCR, #10 X 1.0 PPHST TYPE B
TANK, ADM SOLUTION
VENT, COOLING AIR SMALL
WASHER, #10 X 9/16 OD
STRAINER, 3/8 IN. NPT 60 MESH
WASHER, 1/4 ID X 5/8 OD SS
SCR, 1/4-20 X 1/2 PPHMS SS DL
CLAMP, 3.5" WORM GEAR
GASKET, TANK, L-F
GASKET, TANK, L-R
GASKET, TANK, RH
HOSEBARB, 3/8MPTX1/2 90D DL
SCR, 1/4-20 X.75 PPHMS PHIL
WASHER, 1/4 LOCK EXT STAR SS
SCR, #10 X 3/4 PPHST TYPE B
WELDMENT, HANDLE PIVOT ADM8
NUT, 1/4-20 HEX NYLOCK SS
HOSE ASSY- FILL HOSE
CLAMP, 3/8 HOSE (D-SLOT)
HOSEBARB, 1/2MPT X 3/8 DL
33
86026670
75277
1
TANK ASM, SOLUTION ADM8
CLAMP, 2.0" WORM GEAR
CLAMP, 3/8 HOSE (D-SLOT)
COVER, VAC MOTOR
COVER, BELT
ELBOW, 3/8 MPT X 3/8 TUBE,
PLASTIC
GASKET, TANK TO VAC COVER
GASKET, VAC COVER (CLP
FAMILY)
HOSE,1/2 CLEAR X 12
HOSE, 1.5 BLK VAC X 3.0
HOSE ASM, 1.5 BLK VAC X 15.5
HOUSING, VAC MOTOR
VAC MOTOR ASM, CLP FAMILY
BRUSH SET, 120V 5.7 VAC,
AMATEK
BRUSH SET, 120V VAC, WINDSOR
ADMIRAL 86038230 03/16/07
SERIAL NO.
FROM
*
*
NOTES:
SERVICE
ONLY
SERVICE
ONLY
*ITEMS
INCLUDED
5-12
RECOVERY TANK ASSEMBLY
16
15
5
E
18
7
11
4
12
8
10
E
1
14
9
12
13
17
2
6
11B
3
10B
1B
14B
12
5-13
ADMIRAL 86038230 03/16/07
RECOVERY TANK ASSEMBLY
REF
PART NO.
PRV NO.
QTY
1A
1B
2
3
4
5
6
7
8
9
10A
10B
11A
11B
12
13
14A
14B
15
16
17
18
86002400
86002350
86233140
86008400
86003110
86235280
86003630
86003910
86003930
86004200
86004510
86004450
86004500
86006240
86006600
86032270
86001370
86001190
86002870
86242230
86245930
86003330
20064
20002
20041
78499
27816
28060
34351
35230
35232
39353
41391
40019
41390
66227
70114
75260
140408
140133
27417
500009
50994
28061
1
1
1
1
2
1
1
1
2
1
1
1
1
1
6
1
1
1
1
1
1
1
DESCRIPTION
CLAMP, 2.0" WORM GEAR X .312
CLAMP, 2.0” NYLON RATCHET
CLAMP, 2.0" WORM GEAR
TETJER, DRAIN PLUG
COVER, REC. TANK
DOME, CLP FAMILY
FLOAT SHUT-OFF
GASKET, DOME
GASKET, PORT COVER
HOSE, 1.5 X 12.0 DRAIN
HOSE, INSERT
HOSEBARB, 1.5 DOUBLE MCHD
HOSE, CAP
PLUG DRAIN HOSE
SCR, #10 X 3/4 PPHST TYPE B
TANK, ADM RECOVERY
BRKT, HOSE HOOK
BRKT, RECOVERY HOSE MTG
CORD, 99807 1/8 X 12"
LABEL, WARNING
LABEL, ADMIRAL MAIN
DOME ASM
ADMIRAL 86038230 03/16/07
SERIAL NO.
FROM
1000083447
NOTES:
1000083447
1000083447
1000083447
5-14
SUGGESTED SPARE PARTS
PART NO.
PRV NO.
86001140
86001100
86000900
86004570
86241680
86026390
86026940
86003780
86001980
86230210
86007140
86007200
86026880
86007970
86003330
86003630
86006240
86135340
86135320
12514
11045
09019
44067
44073
65201
84160
35171
14700
14832
72130
72162
53789
73864
28061
34351
66227
14258
140687
DESCRIPTION
BRUSH, 15L X 3.38OD
BELT, 180J6 MICRO-V
BEARING, 1.125ODX.500IDX.375
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 8003
PUMP ASM, CLP/ADM
VALVE ASM, SOLENOID CLP FAMILY
GASKET, ACCESSORY PORT
BREAKER, 15A 250VAC 50VDC
BREAKER, 6A VDE CIRCUIT
SWITCH, SPST 2-POSITION ROCKER
SWITCH, DPDT3-POSITION ROCKER
VAC MOTOR ASM, CLP FAMILY
STRAINER, 3/8 IN. NPT 60 MESH
DOME ASM, CLP FAMILY
FLOAT SHUT-OFF
PLUG, DRAIN HOSE
BRUSH SET, 120V 5.7 VAC, AMATEK
BRUSH SET, 120V VAC, WINDSOR
Order Parts Here:
www.ivie-ent.com/parts
Ph:(918)254-5161
5-15
ADMIRAL 86038230 03/16/07
SERIAL NO.
FROM
NOTES:
WAS 12031
WAS 44072
Download PDF