BelAire | Air Compressor | Instruction manual | BelAire Air Compressor Instruction manual

Air Compressor
Manual
For questions concerning this air compressor,
please call 866-869-3114
Part# 1312207700
TABLE OF CONTENTS
PAGE
1
Safety Guidelines - Definitions
Before Using the Air Compressor
2
When Installing or Moving the Compressor
Before Each Use
3
Follow Safety Precautions for Electrical Connection
Plan Ahead to Protect Your Eyes, Hands, Face & Ears
When Operating
4
Spraying Precautions
Perform These Maintenance Operations
5
Typical Compressor Installation
Glossary
6-9
Wiring
10-11 Starting the Compressor
12
QP Compressor
13-14 Troubleshooting
15
Pump and Tank Specs
16
Tank Warning
17
Parts Reference
18
Single Stage and Contractor
19
Two Stage
20
Gas Drive and Duplex
21
QP
22
Electric Two Stage and Duplex
23-24 B2800 and B3800
25
T29S
26
B5900
27
T39
28-29 C1
30-31 C2
Back Warranty Statement
SAFETY GUIDELINES - DEFINITIONS
Safety is a combination of common sense, staying alert and knowing how your compressor works.
Read this manual to understand this compressor.
DANGER
means if safety information is not followed someone will be seriously injured or killed
WARNING
means if safety information is not followed someone could be seriously injured or killed
CAUTION
means if safety information is not followed someone may be seriously injured or killed
IMPORTANT SAFETY INSTRUCTIONS
Save these instructions
Improper operation or maintenance of this product could result in serious injury and property
damage. Read and understand all warnings and operation instructions before using this compressor.
Before using the air compressor
Things you should know
Inspect your work area
Air compressors are utilized in a variety of air
1. Keep work area clean.
system applications. Because air compressors
2. Cluttered areas and benches invite accidents.
and other components (hoses, connectors, air
Floors must not be slippery from wax or dust.
tools, spray guns, etc.) make up a high pressure
pumping system, the following safety precautions should be observed at all times.
Inspect your compressor
Only persons familiar with these rules of
safe operation should use the air
compressor.
1. To reduce the risk of injury from accidental
starting, turn switch off and disconnect the
power before checking it.
1. Read the instruction manual carefully before
attempting to assemble, disassemble or
operate your system. Be thoroughly familiar
with the controls and the proper use of the
equipment.
2. If any part is missing, bent or broken in any
way, or any electrical part does not work properly, keep the compressor off and disconnected.
3. Review the maintenance methods for this
compressor (See “Maintaining Your
Compressor” section).
Do not operate compressor if damaged during
shipping, handling or use. Damage may result
in bursting and cause injury or property damage.
3. Check hoses for weak or worn condition
before each use, making certain all connections
are secure. Do Not use if defect is found.
2. Review and understand all safety instructions
and operating procedures in this manual.
WARNING
DANGER
This compressor is Not designed for and should
not be used in breathing air applications.
Page 1
When installing or moving the compressor
WARNING
6. A minimum clearance of 18 inches between
the compressor and a wall is required
because objects could obstruct airflow.
This compressor is extremely top heavy. The
compressor must be bolted to the floor with
vibration pads before operating to prevent
equipment damage, injury or death. Do Not
tighten bolts completely as this may
cause stress to the tank welds. Chart 1a.
7. The compressor should be located where it can
be directly wired to a circuit breaker. The
compressor should be wired by a qualified
electrician.
To reduce the risk of a dangerous
environment
8. Never store flammable liquids or gases in
the vicinity of an operating compressor.
1. Keep work area well lit.
2. Operate compressor in a well-ventilated
area free from flammable liquids and vapors.
3. Operate compressor in a ventilated area so
that compressor may be properly cooled and
the surrounding air temperature will not be
more than 100°F.
9. Do Not locate the compressor air inlet near
steam, paint spray, sandblasting areas or
any other source of contamination. The
debris could damage the motor and pump.
WARNING
Never use plastic (PVC) pipe for compressed
air. Serious injury or death could result.
4. Never use a compressor in a wet
environment.
CAUTION
Never use the shipping skid for mounting the
compressor.
5. Protect material lines and air lines from
damage or puncture. Keep hose and
wires away from sharp objects, chemical
spills, oil, solvents and wet floors.
NOTICE
Electric Compressors are not suitable for
outdoor installation.
WARNING
Do Not secure compressor with toggle bolts
into drywall. Drywall sheeting or plaster will not
support the weight of the compressor.
Always Shut Off Gas Valve before
moving Gas Drive Compressors
NOTICE
Gasoline Compressors must be operated
outdoors, sheltered from the weather.
WARNING
Never install a shut off valve between the
compressor pump and tank. Personal injury
and/or equipment damage could occur.
Before each use
Inspect your work area
Inspect your compressor
1. Keep work area clean. Cluttered areas and
benches invite accidents.
1. To reduce the risk of injury from accidental
starting, turn the switch off and disconnect
power.
2. The floor must not be slippery from wax or
dust.
Flat
Washer
Floor
Vibration Pad
Compressor
Leg
Shim
(If Necessary)
Lag Bolt
2. If any part is missing, bent or broken in any
way, or any electrical part does not work
properly, keep the compressor off and disconnect power. Do Not use if defect is found.
3. Check hoses for weak or worn condition
before each use, making certain all connections are secure. Do Not use if a defect is
found.
Chart 1a
Page 2
Follow the safety precautions for electrical connections
1. Follow all local electrical and safety codes,
as well as the National Electric Code (NEC)
and the Occupational Safety and Health
Act (OSHA).
3. Protect wires from contact with sharp objects.
CAUTION
2. Wiring and fuses should follow electrical
codes, current capacity and be properly
grounded.
All electrical connections should be made by
a qualified electrician.
Plan ahead to protect your eyes, hands, face and ears
Dress for safety
1. Wear safety glasses (meeting ANSI Z87.1 or
in Canada CSA Z94.3-99) and use hearing
protection when operating the unit. Everyday
glasses are not safety glasses.
WARNING
Be careful when touching the exterior of compressor, pump, motor and air lines; they may
become hot enough to cause injury.
2. Wear shoes to prevent shock hazards.
WARNING
3. Tie back long hair.
Never operate the compressor without a
beltguard. The compressor can start automatically without warning. Personal injury or
property damage could occur from contact
with moving parts.
Pay attention to your hands
WARNING
Keep fingers away from running compressor.
Fast moving and hot parts may cause injury
and/or burns.
CAUTION
The compressor may be hot even if the unit is
stopped.
WARNING
Use of a mask or respirator per chemical
manufacturers’ instructions may be necessary if there is a chance of inhaling toxic fumes.
Read mask and respirator instructions carefully. Consult a safety expert if you are not
sure about the use of certain masks or
respirators.
When operating
WARNING
1. Do not exceed the pressure rating of any
component of the system.
2. Release pressure within the system slowly
to prevent flying dust and debris.
3. If the equipment starts to abnormally vibrate,
STOP the compressor immediately and
check for the cause.
Never change the safety valve or pressure
switch settings. Keep safety valve free from
paint and other accumulations. See compressor
specification decal for maximum operating
pressure. Do not operate with the pressure
switch set higher than the maximum operating
pressure.
Page 3
Spraying precautions
WARNING
1. Do Not spray in the vicinity of open flames
or other places where a spark can cause
ignition. Do Not smoke when spraying
paint, insecticides, or other flammable
substances.
Never point a spray gun at yourself or any
other person or animal. Accidental discharge
may result in serious injury.
Reduce the risk of dangerous
environment
Be informed about the materials you use
1. When spraying with solvents or toxic chemicals, follow the instructions provided by the
chemical manufacturer. Consult a safety
expert if unsure about the use of masks or
respirators.
WARNING
Extreme caution should be taken when
spraying flammable liquids as the spark from
a motor or pressure switch may cause a fire
or explosion. Ample ventilation must be
provided.
2. If the material you intend to spray contains
trichloreoethane and methylene chloride, do
not use accessories that contain aluminum or
galvanized materials, as these chemicals can
react with galvanized components causing
corrosion and weakening equipment. Use
stainless steel accessories.
WARNING
Spray in a well ventilated area to keep fumes
from collecting and causing serious injury and
fire hazards.
Perform these maintenance operations
1. Do regular maintenance; keep all nuts, bolts,
and screws tight, to be sure equipment is in
safe working condition.
2. Inspect tank yearly for rust, pin holes or any
other imperfections that could cause it to
become unsafe.
4. Drain tanks of moisture after each day’s use.
If unit will not be used for awhile, it is best to
leave the drain cock open until such time as it
is to be used. This will allow moisture to
completely drain out and help prevent
corrosion of inside of tank.
5. Always disconnect from power source before
working on or near a motor, or its connected
load. If power disconnect point is out-ofsight, secure it in the “OFF” position and tag it
to prevent unexpected application of power.
WARNING
NEVER attempt to repair or modify a tank!
Welding, drilling or any other modification will
weaken the tank resulting in damage from
rupture or explosion. Always replace worn,
cracked or damaged tanks.
WARNING
3. Clean electrical equipment with an approved
cleaning agent, such as a dry, non-flammable cleaning solvent.
Disconnect power and depressurize system
before servicing air compressor. Slightly open
drain cock after shutting off compressor.
Daily
Monthly
(Make sure the main power is off.) Check the belts
for tension. Belts should not move up and down
when the compressor runs and when stopped,
should not have more than ½ in of play when
depressed. Be careful not to over tighten belts
during adjustment.
Check oil level at sight glass. Oil level should
be 1/2 to slightly higher in the oil sight glass.
Drain moisture from tank.
Verify the pressure switch unloader is
working by listening for a brief hissing sound
when the compressor shuts off.
Remove and check air filter, replace if necessary.
Visually check the compressor for loose parts,
excessive noise or vibration. Tighten any
necessary part.
Change oil every 3 months or 300 hours. A
compressor grade 30 wt non-detergent oil should
be used. 40 wt non-detergent for single stage.
Page 4
TYPICAL COMPRESSOR INSTALLATION
WIRING
To Air System
Flex
Hose
Regulator
Air
Dryer
See Illustration 1a
Vibration Pads
GLOSSARY OF TERMS
Air Filter
Pressure Switch
Porous element contained within a metal or
plastic housing attached to the compressor
cylinder head which removes impurity from the
intake air of the compressor.
Device which automatically controls the on/off
cycling of the compressor. It stops the
compressor when the cut-off pressure in
the tank is reached and starts the compressor
when the air pressure drops below the cut-in
pressure.
Air Tank
Cylindrical component which contains the
compressed air.
PSI (Pounds per Square Inch)
Check Valve
Measurement of the pressure exerted by the
force of air. The actual psi is measured by a
pressure gauge on the compressor.
Device which prevents compressed air from
flowing back from the air tank to the compressor pump.
Pump
Electric Motor
Device which produces the compressed air
with a reciprocating piston contained within a
cylinder.
Device which provides the rotational force
necessary to operate the compressor pump.
Safety Valve
Pressure Gauge
Device which prevents air pressure in the air
tank from rising over a predetermined limit.
Device which shows the tank or regulated
pressure of the compressed air.
Thermal Overload Switch
Flat
Washer
Floor
Vibration Pad
Compressor
Leg
Shim
(If Necessary)
Device, integrated into the electric motor winding,
which automatically “shuts off” the compressor
if the temperature of the electric motor exceeds
a predetermined limit.
Lag Bolt
Chart 1a
Page 5
WIRING
WIRING
WARNING
ALL ELECTRICAL WIRING SHOULD BE DONE
BY A QUALIFIED ELECTRICIAN
General Information
Adequate wiring and motor protection
Incoming power should
should be provided for all stationary
be connected to L1 and
compressors. Wiring used for other
L2 at the Top of the
machinery should not be used. A
Magnetic Starter.
qualified electrician familiar with local
electrical codes in your area should be
used. Size supply wiring per NEC (National
Electric Code) requirements.
WARNING
To reduce the risk of electrical hazards, fire
hazards or damage to the compressor, use
proper circuit protection. Your compressor
is wired at the factory for operation using
the voltage shown. Connect the compressor
to a power source with the correct breaker
size.
Overload
Adjustment
+
WARNING
-
Electrical connections must be properly
grounded. Ground connections should be
connected at the grounding screw.
Ground
CAUTION
Single Phase
Overheating, short circuiting and fire damage
will result from inadequate wiring.
Incoming power
should be
connected to
L1, L2 & L3 at
the Top of the
Magnetic Starter.
DO NOT MAKE CONNECTIONS
AT THE PRESSURE SWITCH
(Units with Magnetic Starters)
DUPLEX
Power should be brought into the
left hand starter. Do not bring power
to both starters.
For Models Without Magnetic Starter
Incoming power
should be connected
to the posts
marked (LINE)
Do Not Make
Connections On
Prewired Posts
Marked (MOTOR)!
Ground
Three Phase
Electrical connections
must be properly
grounded. Ground
connections should be
connected at a
grounding screw.
Page 6
WIRING
WIRING
Single and Three Phase
With Mag Starter
Page 7
WIRING
WIRING
Single and Three Phase
Duplex
Page 8
WIRING
WIRING
Single and Three Phase
QP
Page 9
STARTING THE COMPRESSOR
STARTING THE COMPRESSOR
Operate the compressor for a few minutes
unloaded (air system open) then allow the
compressor to pump up. Make sure the
electrical pressure switch properly switches
off the compressor according to the setting
desired. 175 for Two Stage.
(135 psi - Single Stage or 165 psi - RCP-561VNS)
Prior to actually running the compressor,
check the following items:
Crankcase oil - Make sure the sight glass
shows ½ full or slightly above.
Make sure all rags, tools, oil, etc. are away
from the unit.
CAUTION
Make sure the pressure in the tank does
not exceed its rating. Single Stage units - 135 psi
Two Stage units at a maximum of 175 psi.
(165 for Model RCP-561VNS)
If the pressure gauge indicates a pressure that
is higher than these maximum pressures,
shut off compressor immediately and call
your distributor.
Open the air system to free it of any pressure.
Switch the compressor on for a few
revolutions to make sure the rotation is
correct. Correct rotation is clockwise
when facing the sight glass on the pump.
(Gas Drive Models)
PLEASE REFER TO YOUR ENGINE OPERATION MANUAL FOR PROPER STARTING
INSTRUCTIONS.
GASOLINE DRIVEN COMPRESSORS ARE EQUIPPED WITH A COLD START
VALVE FOR LOADLESS STARTS.
NOTE: IN SOME INSTANCES, IT STILL
MAY BE NECESSARY LIFT THE TOGGLE ON THE UNLOADER/PILOT VALVE
TO RELIEVE THE HEAD PRESSURE. See Page 11
Battery Connection Instructions for Electric Start Engines
Note:Make sure to follow instructions carefully to avoid a short and possible damage
to the starter solenoid and/or battery.
1. Connect the positive (+) terminal on the battery to the starter solenoid.
2. Connect the negative (-) terminal on the battery to an engine mounting bolt or other
acceptable ground connection.
Always connect the positive(+) battery cable to the starter solenoid before connecting
the negative(-) battery cable.
NUMBER 2 WIRE OR LARGER IS REQUIRED
(-)
(+)
BATTERY
(12 Volt)
Starter Solenoid
GROUND
Page 10
Cold Start Procedure (Gasoline Engine Units)
Warning: Do Not Operate Gasoline Engine
Units in an Enclosed Area
· Release any remaining tank pressure by slowly opening the
manual drain valve.
· Turn on the engine gasoline supply.
· Put the choke in the “On” position
· Close the service valve and put Unloader lever in the “unload”
(A) position for Briggs and Stratton and Honda engine driven
models, or the “load” (B) position for Kohler engine models.
· Start the engine, release the choke, and allow the engine to
warm up for two to three minutes.
· Return the unloader lever to the “load” (B) position on Briggs
and Stratton and Honda driven models.
Note: Turn the gasoline supply off when the compressor is
not being used
Page 11
QP Compressors
You have purchased a state of the art BelAire QP compressor. The QP comes equipped
with sound attenuating enclosure. For maintenance, the canopy and side foam pieces will need
to be removed.
To remove the canopy, simply remove the 6 fasteners and lift the canopy straight up and off.
QP and Elite Compressors
BelAire ELITE and QP models come equipped with low oil level switches and automatic tank
drains. The QP models also include protection against over-heating.
Low Oil Level Switch
The function of the low oil level switch
is to keep the air compressor from
starting if the oil level drops beyond
a certain point.
For compressors outfitted with the
low oil level switch, the oil should
in the top 1/3 of the oil sight glass.
Oil Vent
Plug
Target Oil Level
When changing or adding oil, it is
important to remove the Oil Vent
Plug to allow for the oil to flow
completely into the switch.
OIL
(Please Note: If overfilled, oil will flow out
of the oil vent hole)
Thermal Protection - QP Models
If the cooling fan were to fail or
internal temperature were to reach
180°F the QP models are outfitted
with a thermal fuse.
When tripped, the fuse can be reset.
The canopy will need to be removed
to reset the thermal fuse.
Press to
Reset
Location of Fuse
(Inside Canopy
Behind Fan)
Page 12
TROUBLESHOOTING GUIDE
Low discharge pressure 1. Compressor too small for
application
2. Air leaks
3. Restricted intake air
4. Blown gasket(s)
5. Broken or misaligned valves
1. Reduce air demand or use a compressor
with more air capacity.
2. Listen for air leaks. Apply a soap solution
to all fittings and connections. Bubbles
will form at points of leakage. Tighten
or replace fittings or connections.
3. Clean or replace air filter.
4. Replace necessary gaskets.
5. Remove head and inspect for broken or
misaligned valves. Replace valves, if
necessary.
!
Excessive noise
“knocking”
1. Loose drive pulley or flywheel
2. Low on oil
3. Worn connecting rod or
connecting rod bearing
4. Noisy check valve
CAUTION
Install a new head gasket
each time head is removed
1. Tighten drive pulley or flywheel bolt.
2. Check for proper oil level. Low or dirty
oil may cause bearing damage.
3. Replace connecting rod and/or connecting
rod bearings.
4. Replace check valve.
!
DANGER
Do not remove check valve
with air pressure in tank
Excessive oil carryover
1. Worn piston rings
2. Restricted intake air
3. Too much oil in compressor
4. Incorrect oil viscosity
1. Replace with new piston rings.
2. Clean or replace air filter.
3. Drain oil to proper oil level.
4. Use a quality non-detergent 30 or 40wt
oil specified for each model (Page 4).
Water in tank and/or
discharge line
1. Normal. Amount of water will
increase as humidity in the
air increases.
1. Drain tank at least once per day.
2. Add an inline filter to reduce moisture in
the air line.
Will not run or motor
hums
1. Low voltage
1. Check voltage with volt meter across both
legs of incoming power. Check reset button
on motor.
2. Malfunctioning pressure switch 2. Repair or replace pressure switch.
3. Malfunctioning check valve
3. Replace check valve or pressure switch.
!
Breaker or reset
repeatedly trips
Do not remove check valve
with air pressure in tank
1. Make sure the breaker is sized properly.
See page 6 in this manual.
2. Check voltage with volt meter across both
2. Low voltage
legs of incoming power.
3. Replace motor.
3. Malfunctioning motor
4. Check all electrical connections.
4. Loose electrical connections
5. Malfunctioning pressure switch 5. Adjust or replace pressure switch.
6. Replace check valve.
6. Malfunctioning check valve
1. Incorrect breaker size
!
Tank does not hold
pressure when not
running and shut off
valve is closed
DANGER
1. Malfunctioning check valve
Page 13
Do not remove check valve
with air pressure in tank
1. Replace check valve.
!
2. Loose fittings or connections
3. Crack or pin hole in tank
DANGER
not remove check valve
DANGER Do
with air pressure in tank
2. Tighten or replace fittings or connections.
3. Replace tank. Do not attempt to repair tank.
TROUBLESHOOTING GUIDE (Continued)
Pressure switch unloader constantly
leaking air
1. Malfunctioning check valve
Pressure switch not
unloading
1. Malfunctioning pressure
switch
1. Replace check valve if unloader bleeds
constantly.
!
1. Replace pressure switch if it does not release
air pressure briefly when unit shuts off.
!
Excessive vibration
1. Improper installation
2. Loose belts
3. Misaligned flywheel or
drive pulley
Overheating
1. Compressor too small for
application
2. Cooling surfaces dirty
3. Improper cooling
Page 14
not remove check valve
DANGER Do
with air pressure in tank
DANGER
Do not remove pressure
switch with air pressure in
tank
1. Make sure unit is mounted on a level surface
with vibration pads.
2. Replace belts. Align and tighten properly.
3. Align flywheel and drive pulley.
1. Reduce air demand or use a compressor
with more air capacity.
2. Clean all cooling surfaces of dirt and dust.
3. Install compressor in an area with adequate
cool dry air.
PumpWIRING
Specifications
Pump
Model
PAT24
B3800
T39
T29S
B5900
C1
C2
Pump
Model
PAT24
PAT38
T39
T29S
B5900
C1
C2
Pump
Model
PAT24
PAT38
T39
T29S
B5900
C1
C2
Pump P/N
4116091136
4116091337
4116090019
4116090112
4116090137
1312100706
1312202700
Cyl. No.
2
2
2
2
2
2
4
Cyl. Diam. In. (mm)
1st Stg
2nd Stg
2.48 (63)
N/A
2.48 (63)
N/A
4.13 (105)
2.05 (52)
3.74 (85)
1.97 (45)
4.13 (105)
2.16 (55)
4.13 (105)
2.16 (55)
4.13 (105)
2.16 (55)
Conrod
N/A
N/A
20-22 (27-30)
18-20 (24-27)
18-20 (24-27)
34-37 (46-50)
34-37 (46-50)
Stages
1
1
2
2
2
2
2
Stroke in.
(mm)
1.50 (38)
2.36 (60)
2.95 (60)
1.97 (45)
2.16 (55)
3.5 (89)
3.5 (89)
Oil Cap.
Qt. (L)
.56 (0.53 )
.91 (.86)
1.09 (1.03)
1.44 (1.36)
1.72 (1.63)
1.31 (1.24)
1.5 (1.42)
Max rpm
1400
1400
1400
1400
1400
1000
900
Bolt Torque Ft.-Lbs. (NM)
Head
Cylinder
Bearing Housing
18-20 (24-27) 18-20 (24-27)
5-7 (7-10)
18-20 (24-27) 18-20 (24-27)
5-7 (7-10)
30-33 (40-45) 16-19 (22-26)
19-22 (26-30)
18-20 (24-27) 18-20 (24-27)
5-7 (7-10)
18-20 (24-27) 18-20 (24-27)
5-7 (7-10)
34-37 (46-50) 19-27 (26-37)
14-19 (19-26)
34-37 (46-50) 19-27 (26-37)
14-19 (19-26)
Flywheel
18-20 (24-27)
18-20 (24-27)
34-37 (46-50)
18-20 (24-27)
18-20 (24-27)
47-57 (64-77)
47-57 (64-77)
WIRING
Tank Specifications
Volume
Gal. Liter
20H
76
26V
99
60V
228
2X4 2X15.2
2X5 2X19
80H 228
80V
300
30H 114
120V 456
120H 456
120D 456
200D 760
Max Pressure Discharge Conn.
PSI
Bar
NPT
150 10.345
1/4"
150 10.345
1/4"
170 11.724
1/2'
200 13.793
3/8"
200 13.793
3/8"
200 13.793
3/4"
200 13.793
3/4"
200 13.793
3/4"
200 13.793
3/4"
200 13.793
3/4"
200 13.793
3/4"
200 13.793
3/4"
Page 15
Displacement @ max RPM
CFM
L/M
11.71
331.59
18.49
523.58
32.02
906.63
17.53
496.50
23.44
663.84
27.13
768.33
48.84
1382.99
WARNING
Oil and moisture residue must be drained from the air receiver
daily or after each use. Accumulations of oil residue in the receiver
can be ignited by embers of carbon created by the heat of compression causing an explosion, damage to property and injury to personnel
WARNING
Do not open a manual tank drain valve on any air tank containing
more than 30 PSIG of air pressure!
WARNING
Never attempt to releive an air tank by removing a pipe plug or
any other system component!
Manually Draining An Air Tank:
Step 1)
Disconnect & lockout the compressor from the power source (elec
tric models) or disconnect the spark plug wire from the spark plug
(gas engine models).
Step 2)
Tank(s) subjected to freezing temperatures may contain ice. Store
the compressor in a heated area before attempting to drain mois
ture from the tank(s). Reduce the air pressure in the tank to 30
PSIG by pulling the pressure relief valve ring (refer to
Fig. 3-4,
Checking Pressure Relief Valves & Relieving System Pres
sure ).
Step 3)
Slowly open the drain valve and allow the moisture and air mixture
to drain from the tank.
Step 4)
Once the moisture has been completely drained, close the drain
valve.
Air Tank Inspection
Horizontal
Tank Capacity
or
Vertical
8 Gal.
Horizontal
8 Gal.
Twin Horz.
10 Gal.
Twin Horz.
20 Gal.
Horizontal
26 Gal.
Vertical
30 Gal.
Horizontal
60 Gal.
Vertical
80 Gal.
Vertical
80 Gal.
Horizontal
120 Gal.
Vertical
120 Gal. & Duplex Horizontal
200 Gal. Duplex Horizontal
Minimum
Allowable Wall
HEAD
SHELL
0.096
0.094
0.098
0.098
0.118
0.118
0.094
0.094
0.094
0.094
0.109
0.098
0.094
0.094
0.149
0.133
0.109
0.133
0.163
0.199
0.131
0.159
0.163
0.199
Visually
Inspect
Hydrostaticall
y Inspect
Yearly
Yearly
Yearly
Yearly
Yearly
Yearly
Yearly
Yearly
Yearly
Yearly
Yearly
Yearly
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
Recommended Air Tank Inspection Intervals
Page 16
The factory recommends that all
air tanks be inspected at scheduled inter vals. Refer to Recommended Air
Tank Inspection Intervals Table for
relative information.
Refer to federal, state or provincial,
or local codes for mandatory air tank
maintenance information.
Part Callouts
Electric
Discharge Line
Compressor
Drive Belt
Inlet Filter
Motor
Pressure Switch
Pressure Gauge
Check Valve
Magnetic Starter
Tank
Ball Valve
Water/Tank Drain
Gas Drive
Inlet Filter
Drive Belt
Compressor
Engine
Belt Guard
Idle Control
Pilot/Unloader Valve
Pressure Gauge
Ball Valve
Tank
Water/Tank Drain
Page 17
Single Stage
*Note: Verify Model and Part Number of Machine Before Ordering
Change has been made to Compressor Pumps (March-April 2014)
*Model 5020P (Part# 8090254163)
Model 5026VP (Part# 8090254106)
Model 2061V (Part# 8090254064)
Model 6061V (Part# 8090254007)
Compressor
Motor
Tank
Check Valve
Pressure Switch
Safety Valve
Pressure Gauge
Discharge Line
Inlet Filter
Water Drain
BeltGuard (front)
BeltGuard (back)
Drive Pulley
Drive Belt
Unloader Line
Power Cord
Wheel
Handle
5020P*
5026VP*
2061V*
6061V*
4116091336
1312100388
1312100473
1312100170
1312100455
1312100005
1312100006
1312101048
2236111635
1312100360
6214343100
2236110472
1312100439
1312101067
1312100026
1312100007
1312100060
2236107285
4116091336
1312100388
1312100475
1312100170
1312100455
1312100005
1312100006
1312101048
2236111635
1312100360
6214343100
2236110472
1312100439
1312101067
1312100026
1312100007
1312100029
2236107294
4116091337
1312100388
1312100460
1312100170
1312100455
1312100005
1312100840
1312101047
2236111635
1312100360
6214343100
2236110472
1312101154
1312100132
1312100026
N/A
N/A
N/A
4116091337
1312100390
1312100460
1312100170
1312100455
1312100005
1312100840
1312101047
2236111635
1312100360
6214343100
2236110472
1312101070
1312100807
1312100026
N/A
N/A
N/A
ELECTRIC
*Model T2030 (Part# 8090254239)
Contractor
*Model TH5530 (Part# 8090254262)
Model TR6030 (Part# 8090254296)
Compressor
Motor
Tank
Check Valve
Pressure Switch
Safety Valve
Pressure Gauge
Discharge Tube
Ball Valve
Inlet Filter
Tank Drain
Unloader Line
BeltGuard (front)
BeltGuard (back)
Belt Guard Fastener
Drive Pulley
Drive Belt
T2030
4116091337
1312100388
1312100521
1312100170
1312100455
1312100005
1312100845
1312101156
1312100161
2236111635
1312100360
1312100026
1312100146
1312100147
1312100076
1312101154
1312100129
Wheel
Power Cord
1312100461
1312100007
GAS DRIVE
Compressor
Engine
Tank
Idle Control
Unloader/Pilot Valve
Safety Valve
Pressure Gauge
Discharge Tube
Ball Valve
Inlet Filter
Tank Drain
BeltGuard (front)
BeltGuard (back)
Belt Guard Fastener
Drive Pulley
Drive Belt
Wheel
TH5530
4116091337
1312100219
1312100521
1312100382
1312100496
1312100005
1312100845
1312101160
1312100161
2236111635
1312100360
1312100146
1312100147
1312100076
1312101070
1312100131
1312100461
TR6030
4116091337
1312100230
1312100521
1312100382
1312100496
1312100005
1312100845
1312101160
1312100161
2236111635
1312100360
1312100146
1312100147
1312100076
1312101070
1312100131
1312100461
Page 18
TR908
4116090019
1312100231
1312100520
1312100382
1312100495
9710533300
1312100845
1312100204
1312100161
1312100374
1312100360
1312100150
1312100149
1312100076
1312100419
1312100136
1312100461
TH908
4116090019
1312100221
1312100520
1312100382
1312100495
9710533300
1312100845
1312100204
1312100161
1312100374
1312100360
1312100150
1312100149
1312100076
1312100419
1312100137
1312100461
TK128-I
4116090019
1312101114
1312100520
1312100571
1312100495
9710533300
1312100845
1312100204
1312100161
1312100374
1312100360
1312100150
1312100149
1312100076
1312100419
1312100136
1312100461
Two Stage Electric
Pump
Motor
Tank
Check Valve
Pressure Switch
Safety Valve
Pressure Gauge
216V
4116090112
1312100087
1312100460
1312100170
1312100459
1310251870
1312100840
218V
4116090112
1312100389
1312101018
1312100170
1312100570
9710533300
1312100845
318VN
4116090019
1312100389
1312101018
1312100171
1312100570
9710533300
1312100845
Discharge Line
1312100214
1312100200
1312100198
Ball Valve
1312100162
1312100163
1312100163
Inlet Filter
1312100376
1312100376
1312100374
Water Drain
1312100360
1312100360
1312100360
Belt Guard (Front)
1312100146
1312100150
1312100150
Belt Guard (Back)
1312100145
1312100148
1312100148
Belt Guard Clip
1312100076
1312100076
1312100076
Drive Pulley
1312100442
1312100442
1312100418
Drive Belt
1312100133
1312100137
1312100137
Magnetic Starter
No Starter Req. No Starter Req. No Starter Req.
Single Phase (208V-230V)
N/A
N/A
N/A
Three Phase (208-230V)
N/A
N/A
N/A
Three Phase (460V)
N/A
N/A
N/A
AfterCooler
Pump Mounted Pump Mounted Pump Mounted
Low Oil Level Switch
N/A
N/A
N/A
Auto Tank Drain
N/A
N/A
N/A
Beltguard Aftercooler
N/A
N/A
N/A
318V
4116090019
1312100399
1312101018
1312100171
1312100570
9710533300
1312100845
318H
4116090019
1312100399
1312100485
1312100171
1312100570
9710533300
1312100845
338V/4
4116090019
1312101602
1312101018
1312100171
1312100570
9710533300
1312100845
338H/4
4116090019
1312101602
1312100485
1312100171
1312100570
9710533300
1312100845
318VE
4116090019
1312100399
1312101018
1312100171
1312100570
9710533300
1312100845
318HE
4116090019
1312100399
1312100485
1312100171
1312100570
9710533300
1312100845
338VE/4
4116090019
1312101602
1312101018
1312100171
1312100570
9710533300
1312100845
1312100198
1312100163
1312100374
1312100360
1312100150
1312100148
1312100076
1312100422
1312100140
1312100199
1312100163
1312100374
1312100360
1312100150
1312100148
1312100076
1312100422
1312100140
1312100198
1312100163
1312100374
1312100360
1312100150
1312100148
1312100076
1312100422
1312100140
1312100199
1312100163
1312100374
1312100360
1312100150
1312100148
1312100076
1312100422
1312100140
1312100198
1312100163
1312100374
1312100360
1312100150
1312100148
1312100076
1312100422
1312100140
1312100199
1312100163
1312100374
1312100360
1312100150
1312100148
1312100076
1312100422
1312100140
1312100198
1312100163
1312100374
1312100360
1312100150
1312100148
1312100076
1312100422
1312100140
1312100659
N/A
N/A
Pump Mounted
N/A
N/A
N/A
1312100659
N/A
N/A
Pump Mounted
N/A
N/A
N/A
N/A
1312100656
1312100654
Pump Mounted
N/A
N/A
N/A
N/A
1312100656
1312100654
Pump Mounted
N/A
N/A
N/A
1312100659
N/A
N/A
Pump Mounted
1310711181
1312100110
N/A
1312100659
N/A
N/A
Pump Mounted
1310711181
1312100110
N/A
N/A
1312100656
1312100654
Pump Mounted
1310711181
1312100110
N/A
Pump
Motor
Tank
Check Valve
Pressure Switch
Safety Valve
Pressure Gauge
338HE/4
4116090019
1312101602
1312100485
1312100171
1312100570
9710533300
1312100845
318VL
4116090019
1312100400
1312101018
1312100171
1312100570
9710533300
1312100845
318HL
4116090019
1312100400
1312100485
1312100171
1312100570
9710533300
1312100845
338VL/4
4116090019
1312101601
1312101018
1312100171
1312100570
9710533300
1312100845
338HL/4
4116090019
1312101601
1312100485
1312100171
1312100570
9710533300
1312100845
318VLE
4116090019
1312100400
1312101018
1312100171
1312100570
9710533300
1312100845
318HLE
4116090019
1312100400
1312100485
1312100171
1312100570
9710533300
1312100845
338VLE/4
4116090019
1312101601
1312101018
1312100171
1312100570
9710533300
1312100845
338HLE/4
4116090019
1312101601
1312100485
1312100171
1312100570
9710533300
1312100845
Discharge Line
Ball Valve
1312100199
1312100163
1312100198
1312100163
1312100199
1312100163
1312100198
1312100163
1312100199
1312100163
1312100198
1312100163
1312100199
1312100163
1312100198
1312100163
1312100199
1312100163
Inlet Filter
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
Water Drain
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
Belt Guard (Front)
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
Belt Guard (Back)
1312100148
1312100148
1312100148
1312100148
1312100148
1312100148
1312100148
1312100148
1312100148
Belt Guard Clip
1312100076
1312100076
1312100076
1312100076
1312100076
1312100076
1312100076
1312100076
1312100076
Drive Pulley
1312100422
1312100420
1312100420
1312100420
1312100420
1312100420
1312100420
1312100420
1312100420
Drive Belt
1312100140
1312100139
1312100139
1312100139
1312100139
1312100139
1312100139
1312100139
1312100139
Single Phase (208V-230V)
N/A
1312100662
1312100662
N/A
N/A
1312100662
1312100662
N/A
N/A
Three Phase (208-230V)
1312100656
N/A
N/A
1312100658
1312100658
N/A
N/A
1312100658
1312100658
Three Phase (460V)
1312100654
N/A
N/A
1312100657
1312100657
N/A
N/A
1312100657
1312100657
Magnetic Starter
AfterCooler
Pump Mounted
Pump Mounted
Pump Mounted
Pump Mounted
Pump Mounted
Pump Mounted
Pump Mounted
Pump Mounted
Pump Mounted
Low Oil Level Switch
1310711181
N/A
N/A
N/A
N/A
1310711181
1310711181
1310711181
1310711181
Auto Tank Drain
1312100110
N/A
N/A
N/A
N/A
1312100110
1312100110
1312100110
1312100110
Beltguard Aftercooler
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 19
Gas Drive and Duplex
Gas Drive
Compressor
Engine
Tank
Unloader Valve
Safety Valve
Pressure Gauge
Discharge Line
Ball Valve
Inlet Filter
Tank Drain
BeltGuard (front)
BeltGuard (back)
Belt
Beltguard Clip
Unloader Line
Idle Control
Drive Pulley
59G3HR
4116090137
1312100232
1312100479
1312100497
9710533300
1312100845
1312100209
1312100163
6211471600
1312100361
1312100150
1312100149
1312100136
1312100076
1312100373
1312100382
1312100443
59G3HB
4116090137
1312100730
1312100479
1312100497
9710533300
1312100845
1312100209
1312100163
6211471600
1312100361
1312100150
1312100149
1312100137
1312100076
1312100373
1312100742
1312100443
3G3HH
4116090019
1312100223
1312100479
1312100497
9710533300
1312100845
1312100217
1312100163
1312100374
1312100361
1312100150
1312100149
1312100120
1312100076
1312100373
1312100382
1312100419
3G3HK
4116090019
1312100998
1312100479
1312100497
9710533300
1312100845
1312100208
1312100163
1312100374
1312100361
1312100150
1312100149
1312100120
1312100076
1312100373
1312100099
1312100419
Cast Iron Units
Compressor
Engine
Tank
Unloader Valve
Safety Valve
Pressure Gauge
Discharge Line
Ball Valve
Inlet Filter
Tank Drain
BeltGuard
4G3HH
1312202800
1312100223
1312100479
1312101115
9710533300
1312100845
1312101101
1312100163
1312100374
1312100361
1312101093
4G3HHL
1312202800
1312100224
1312100479
1312101115
9710533300
1312100845
1312101101
1312100163
1312100374
1312100361
1312101093
4G3HKL
1312202800
1312101114
1312100479
1312101115
9710533300
1312100845
1312101101
1312100163
1312100374
1312100361
1312101093
6G3HV
1312202700
1312100731
1312101113
1312100497
9710533300
1312100845
1312100720
1312100162
1312100374
1312100360
1312204300
Belt
1312100993
1312101138
1312101138
1312100736
Beltguard Clip
1312101027
1312101027
1312101027
1312100360
Unloader Line
1312100373
1312100373
N/A
N/A
Idle Control
1312101049
1312101049
1312100099
1312100741
Drive Pulley
1312100711
1312101040
1312101040
1312100711
3G3HKL
4116090019
1312100998
1312100479
1312100497
9710533300
1312100845
1312100217
1312100163
1312100374
1312100361
1312100150
1312100149
1312100120
1312100076
1312100373
1312100099
1312101044
3G3HHL
4116090019
1312100224
1312100479
1312100497
9710533300
1312100845
1312100217
1312100163
1312100374
1312100361
1312100150
1312100149
1312100121
1312100076
1312100373
1312100382
1312100421
Duplex
3112D
3312D
3312D4
3112DL
3312DL
3312DL4
3120DL
3320DL
3320DL4
Compressor
4116090019
4116090019
4116090019
4116090019
4116090019
4116090019
4116090019
4116090019
4116090019
Motor
1312100399
1312101602
1312101602
1312100400
1312101601
1312101601
1312100400
1312101601
1312101601
Tank
1312100463
1312100463
1312100463
1312100463
1312100463
1312100463
1312100665
1312100665
1312100665
Check Valve
1312100171
1312100171
1312100171
1312100171
1312100171
1312100171
1312100171
1312100171
1312100171
Pressure Switch
1312100570
1312100570
1312100570
1312100570
1312100570
1312100570
1312100570
1312100570
1312100570
Safety Valve
Pressure Gauge
9710533300
1312100845
9710533300
1312100845
9710533300
1312100845
9710533300
1312100845
9710533300
1312100845
9710533300
1312100845
9710533300
1312100845
9710533300
1312100845
9710533300
1312100845
Discharge Line
1312100211(Lt.) 1312100211(Lt.) 1312100211(Lt.) 1312100211(Lt.) 1312100211(Lt.) 1312100211(Lt.) 1312100211(Lt.) 1312100211(Lt.) 1312100211(Lt.)
1312100212(Rt.) 1312100212(Rt.) 1312100212(Rt.) 1312100212(Rt.) 1312100212(Rt.) 1312100212(Rt.) 1312100212(Rt.) 1312100212(Rt.) 1312100212(Rt.)
Ball Valve
1312100160
1312100160
1312100160
1312100160
1312100160
1312100160
1312100160
1312100160
1312100160
Inlet Filter
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
1312100374
Filter Element
FE001
FE001
FE001
FE001
FE001
FE001
FE001
FE001
FE001
Water Drain
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
1312100360
Belt Guard (Front)
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
1312100150
Belt Guard (Back)
1312100149(Rt.) 1312100149(Rt.) 1312100149(Rt.) 1312100149(Rt.) 1312100149(Rt.) 1312100149(Rt.) 1312100149(Rt.) 1312100149(Rt.) 1312100149(Rt.)
1312100148(Lt.) 1312100148(Lt.) 1312100148(Lt.) 1312100148(Lt.) 1312100148(Lt.) 1312100148(Lt.) 1312100148(Lt.) 1312100148(Lt.) 1312100148(Lt.)
Drive Belt
1312100140
1312100140
1312100140
1312100139
1312100139
1312100139
1312100139
1312100139
1312100139
Drive Pulley
1312100422
1312100422
1312100422
1312100420
1312100420
1312100420
1312100420
1312100420
1312100420
Unloader Line
Magnetic Starter
Alternator
1312100373
1312100659
1312100111
1312100373
1312100656
1312100111
1312100373
1312100654
1312100112
1312100373
1312100662
1312100111
1312100373
1312100658
1312100111
1312100373
1312100657
1312100112
1312100373
1312100662
1312100111
1312100373
1312100658
1312100111
1312100373
1312100657
1312100112
Page 20
QP
Compressor
Motor
Tank
Check Valve
Press. Switch
Safety Valve
Press. Gauge
Mag. Starter
Canopy
Tank Drain
Ball Valve
Disch. Line
Inlet Filter
Low Oil Switch
Blower
Belt Guard (Back)
Belt Guard (Front)
Belt
Belt Guard Clip
Unloader Line
Drive Pulley
High Temp Switch
QP318VE
QP338VE
QP318VLE
QP338VLE
4116090019
4116090019
4116090019
4116090019
1312100399
1312100602
1312100400
1312101601
1312101018
1312101018
1312101018
1312101018
1312100171
1312100171
1312100171
1312100171
1312100570
1312100570
1312100570
1312100570
9710533300
9710533300
9710533300
9710533300
1312100845
1312100845
1312100845
1312100845
1312100659
1312100656
1312100662
1312100658
1312202180
1312202180
1312202180
1312202180
1312100110
1312100110
1312100110
1312100110
1312100163
1312100163
1312100163
1312100163
1312100198
1312100198
1312100198
1312100198
1312100097
1312100097
1312100097
1312100097
1310711181
1310711181
1310711181
1310711181
1312100088
1312100088
1312100088
1312100088
1312100148
1312100148
1312100148
1312100148
1312100150
1312100150
1312100150
1312100150
1312100140
1312100140
1312100139
1312100139
1312100076
1312100076
1312100076
1312100076
1312100373
1312100373
1312100373
1312100373
1312100422
1312100422
1312100420
1312100420
1312100089
1312100089
1312100089
1312100089
Page 21
Iron Series
Compressor
Motor
Belt Guard
Discharge Line (Top)
Discharge Line (Btm)
Pressure Switch
Ball Valve
Unloader Line
Safety Valve
Pressure Gauge
Tank
Tank Drain
418VE
1312100706
1312100399
1312100982
1312101101
1312101102
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
1312100110
Magnetic Starter
1312100659
Drive Pulley
Bushing
Belt
Check Valve
1312100714
1312100445
1312100993
1312100167
438VE/4
1312100706
1312101602
1312100982
1312101101
1312101102
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
1312100110
1312100656 (208-230V)
1312100654 (460V)
1312100714
1312100445
1312100993
1312100167
418V
1312100706
1312100399
1312100982
1312100994
438V/4
1312100706
1312101602
1312100982
1312100994
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
1312100360
1312100714
1312100445
1312100993
1312100169
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
1312100360
1312100656 (208-230V)
1312100654 (460V)
1312100714
1312100445
1312100993
1312100169
Aftercooler
Low Oil Switch
LOS - Housing
1312100611
1312100014
1312100013
1312100611
1312100014
1312100013
Compressor
Motor
Belt Guard
Discharge Line (Top)
Discharge Line (Btm)
Pressure Switch
Ball Valve
Unloader Line
Safety Valve
Pressure Gauge
Tank
418VLE
1312100706
1312100400
1312100982
1312101101
1312101102
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
438VLE/4
1312100706
1312101601
1312100982
1312101101
1312101102
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
418VL
1312100706
1312100400
1312100982
1312100994
438VL/4
1312100706
1312101601
1312100982
1312100994
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
1312100570
1312100163
1312100026
9710533300
1312100845
1312101018
1312100360
1312100659
Tank Drain
1312100110
Magnetic Starter
1312100662
Drive Pulley
1312100938
1312100110
1312100658 (208-230V)
1312100657 (460V)
1312100938
1312100938
1312100360
1312100658 (208-230V)
1312100657 (460V)
1312100938
Bushing
1312100445
1312100445
1312100445
1312100445
Belt
1312100939
1312100939
1312100939
1312100939
Check Valve
1312100167
1312100167
1312100169
1312100169
Aftercooler
1312100611
1312100611
Low Oil Switch
1312100014
1312100014
LOS - Housing
1312100013
1312100013
6312V/4
6312H/4
6312VE/4
6312HE/4
Compressor
1312202700
1312202700
1312202700
1312202700
1312100662
Motor
1312101600
1312101600
1312101600
1312101600
Belt Guard
1312100983
1312100983
Discharge Line
1312100717
1312100717
1312100983
1312100959 (top)
1312100961 (btm)
1312100163
Ball Valve
1312100570
1312100570
1312100983
1312100959 (top)
1312100960 (btm)
1312100163
Pressure Switch
1312100163
1312100163
1312100570
1312100570
Unloader Line
1312100026
1312100026
1312100026
1312100026
Safety Valve
9710533300
9710533300
9710533300
9710533300
Pressure Gauge
1312100845
1312100845
1312100845
1312100845
Tank
1312100469
1312100465
1312100469
1312100465
Tank Drain
Drive Pulley
1312100360
1312100661 (208-230V)
1312100657 (460V)
1312100713
1312100360
1312100661 (208-230V)
1312100657(460V)
1312100713
1312100110
1312100661 (208-230V)
1312100657 (460V)
1312100713
1312100110
1312100661 (208-230V)
1312100657 (460V)
1312100713
Bushing
1312100446
1312100446
1312100446
1312100446
Magnetic Starter
Page 22
Compressor Pump
4116091336 (PAT24) and
4116091337 (PAT38)
01
03
04
02
05
06
07
11
10
Page 23
09
08
Compressor Pump
4116091336 (PAT24) and
4116091337 (PAT38)
01
02
03
04
05
06
07
Air Filter Kit
Valve Assembly Kit
Gasket Kit
Bearing and Ring Kit
Head Kit
Discharge Elbow Kit
Cylinder Kit
08
09
Oil Level Kit
Conrod Kit
10
Flywheel Kit
11
Crankcase Bottom Kit
Page 24
2236111635
2236112518
2901325045
2901325046
2901325044
2901325047
2236112434(PAT24)
2236112435(PAT38)
6229021000
2236111619(PAT24)
2236111620(PAT38)
6229023400(PAT24)
2901325048(PAT38)
2236112437(PAT24)
2236112438(PAT38)
1
3
2
4
5
8
6
7
Ill. No.
Part Number
Description
1
2
3
4
5
6
7
8
2901324960
2901324961
8973035118
6229017300
2901324962
6229017600
2901324950
2901324963
1312100376
FE004
2236102992
6211848600
6214242800
6210717280
Head Kit
Intercooler Kit
Gasket Kit
Overhaul Kit
Aftercooler Kit
Flywheel Kit
Oil Level Kit
65 psi Safety Valve
Filter Assembly
Filter Element
Oil Sight Glass
Flywheel Bolt
Flywheel Washer
Valve Assembly
Page 25
T29S
(4116090112)
1
2
3
4
5
8
7
6
Ill. No.
Part Number
Description
1
2
3
4
5
6
7
8
2901324964
2901324965
8973037264
6229026900
2901324966
6229020100
2901324951
2901324963
2901324974
6211471600
8973035122
6214341200
6211848500
6214242700
6210716900
Head Kit
Intercooler Kit
Gasket Kit
Overhaul Kit
Aftercooler Kit
Flywheel Kit
Oil Level Kit
65 psi Safety Valve
217 psi Safety Valve
Filter Assembly
Filter Element
Oil Sight Glass
Flywheel Bolt
Flywheel Washer
Valve Assembly
Page 26
B5900
(4116090137)
1
3
2
4
5
8
7
Ill. No.
Part Number
Description
1
2
3
4
5
6
7
8
2901324971
2901324972
1310711137
1310711168
2901324973
6229018800
2901324954
1312100456
1312100374*
FE001*
2236102992
6211848500
6214242700
2901324723
1312100097
FE004
Head Kit
Intercooler Kit
Gasket Kit
Overhaul Kit
Aftercooler Kit
Flywheel Kit
Oil Level Kit
225 psi Safety Valve
Filter Assembly
Filter Element
Oil Sight Glass
Flywheel Bolt
Flywheel Washer
Valve Kit
Filter Assembly
Filter Element
*QP Models
Page 27
6
T39
(4116090019)
CA1
(1312202800)
Page 28
CA1
(1312202800)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23.1
23.2
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Description
Crankcase
Crank Shaft
Fly Wheel
Cylinder
Head
Oil Sight Glass
Oil Drain Pipe
Oil Drain Pipe Cap
Oil Fill Elbow
Plug
Spacer - Inlet Valve
Spacer Discharge Valve
Breather Body
Copper Connector
Copper Nut
Cover-Centrifugal Unloader
Valve Assy HP/LP Discharge
Retainer Inlet Valve
Capscrew-Hex M8x25
Lockwasher 8
Retainer Inlet Valve
Gasket Rear Cap
Shim 0.20 Brg. Adj.
Shim 0.10 Brg. Adj.
Retainer Discharge Valve
Copper Elbow
Gasket Side Cover
Cover Crankcase Side
Copper Gasket
Gasket Front Cap
Bearing Cap Rear
Bearing Cone Rear
Bearing Cone Front
Bearing Cap Front
Seal-Shaft
Cap Front
Capscrew-Hex M16x120
Key Fly Wheel C1
Lockwasher 16
Nut - Hex M16
Gasket - Cylinder to Crankcase
Qty
1
1
1
1
1
1
1
1
1
4
2
3
1
1
2
1
2
1
21
8
1
1
1
2
3
1
1
1
14
1
1
1
1
1
1
1
1
1
1
1
1
Part #
1312100876
1312100932
1312100884
1312100880
1312100878
1312100903
1312100859
1312100861
1312100933
1312100866
1312100893
1312100894
1312100934
1312100860
1312100856
1312100899
1312100892
1312100898
0147132503
0333222500
1312100895
1312100920
1312100930
1312100929
1312100896
1312100857
1312100916
1312100858
1312100921
1312100915
1312100909
1312100908
1312100906
1312100907
1312100911
1312100868
0147149203
1312100928
0333224300
0261111403
1312100914
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
Page 29
Capscrew-Hex M10x30
Copper Gasket 10
Aftercooler
Gasket Valve Cover
Elbow - Street
Valve Assy HP Inlet
Safety Valve 250 psi
Gasket Aftercooler
Elbow Aftercooler
Gasket - Cylinder Head
Capscrew - Skt HD M8x30
Capscrew - Skt HD M8x25
Lockwasher 12
Capscrew-Hex M12x70
Gasket Intercooler
Cover Valve
Safety Valve 75 psi
Capscrew-Hex M8x90
Copper Gasket B8
Intercooler
Aluminum Tube 10x380
Filter Inlet Assembly
Filter Replacement Element
Connecting Rod
Dipper-Oil
Insert Half
Bearing- Wrist Pin Needle
Snap Ring - Internal
Wrist Pin LP Piston
Wrist Pin HP Piston
Piston-LP
Piston-HP
Piston Ring Set- LP
Piston Ring Set- HP
Copper Gasket - Valve Seat
Valve Assembly-LP Inlet
Bushing 3/4 x 1 1/4"
Gasket Set
Head Rebuild Kit
Overhaul Kit
6
6
1
3
2
1
1
2
1
1
2
2
8
8
2
3
1
4
7
1
1
1
1
2
2
4
2
4
1
1
1
1
1
1
5
2
1
0147136303
1312100923
1312100875
1312100919
1312100865
1312100891
1312100862
1312100918
1312100873
1312100913
0211132603
0211132503
0333223600
0147140903
1312100927
1312100897
1312100889
0147133803
1312100924
1312100871
1312100863
1312100881
FE001
1312100869
1312100870
1312100905
1312100910
1312100867
1312100901
1312100902
1312100887
1312100888
1312100885
1312100886
1312100922
1312100890
1312100334
1312100925
1312100780
1312100775
CA2
(1312202700)
Page 30
CA2
(1312202700)
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23.1
23.2
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Description
Crankcase
Crank Shaft
Fly Wheel
Cylinder
Head (Left)
Head (Right)
Oil Sight Glass
Oil Drain Pipe
Oil Drain Pipe Cap
Oil Fill Elbow
Plug
Spacer - Inlet Valve
Spacer Discharge Valve
Breather Body
Copper Connector
Copper Nut
Cover-Centrifugal Unloader
Retainer Inlet Valve
Capscrew-Hex M8x25
Lockwasher 8
Retainer Inlet Valve
Gasket Rear Cap
Shim 0.20 Brg. Adj.
Shim 0.10 Brg. Adj.
Retainer Discharge Valve
Copper Elbow
Gasket Side Cover
Cover Crankcase Side
Copper Gasket
Gasket Front Cap
Bearing Cap Rear
Bearing Cone Rear
Bearing Cone Front
Bearing Cap Front
Seal-Shaft
Cap Front
Capscrew-Hex M16x120
Key Fly Wheel C1
Lockwasher 16
Nut - Hex M16
Gasket - Cylinder to Crankcase
Capscrew-Hex M10x30
Copper Gasket 10
Qty
1
1
1
1
1
1
1
1
1
1
4
2
3
1
1
2
1
4
28
8
2
1
1
2
4
1
2
2
26
1
1
1
1
1
1
1
1
1
1
1
1
12
12
Part #
1312100877
1312100931
1312100883
1312100880
1312100878
1312100879
1312100903
1312100859
1312100861
1312100933
1312100866
1312100893
1312100894
1312100934
1312100860
1312100856
1312100899
1312100898
0147132503
0333222500
1312100895
1312100920
1312100930
1312100929
1312100896
1312100857
1312100917
1312100904
1312100921
1312100915
1312100909
1312100908
1312100906
1312100907
1312100911
1312100868
0147149203
1312100928
0333224300
0261111403
1312100914
0147136303
1312100923
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
Page 31
Aftercooler
Gasket Valve Cover
Valve Assy HP Inlet
Safety Valve 250 psi
Gasket Aftercooler
Elbow Aftercooler
Gasket - Cylinder Head
Capscrew - Skt HD M8x30
Capscrew - Skt HD M8x25
Lockwasher 12
Capscrew-Hex M12x70
Gasket Intercooler
Reducing Bushing
Cover Valve
Safety Valve 75 psi
Capscrew-Hex M8x90
Copper Gasket B8
Intercooler
Aluminum Tube 10x380
Filter Inlet Assembly
Filter Replacement Element
Connecting Rod
Dipper-Oil
Insert Half
Bearing- Wrist Pin Needle
Snap Ring - Internal
Wrist Pin LP Piston
Wrist Pin HP Piston
Piston-LP
Piston-HP
Piston Ring Set- LP
Piston Ring Set- HP
Copper Gasket - Valve Seat
Valve Assembly-LP Inlet
Valve Assembly HP/LP
Gasket Set
Head Rebuild Kit
Overhaul Kit
1
6
2
1
4
2
2
4
4
16
16
4
2
6
2
8
14
2
1
2
2
4
4
8
4
8
2
2
2
2
2
2
10
4
4
1
1312100874
1312100919
1312100891
1312100862
1312100918
1312100872
1312100913
0211132603
0211132503
0333223600
0147140903
1312100927
1312100864
1312100897
1312100889
0147140903
1312100924
1312100871
1312100863
1312100881
FE001
1312100869
1312100870
1312100905
1312100910
1312100867
1312100901
1312100902
1312100887
1312100888
1312100885
1312100886
1312100922
1312100890
1312100334
1312100926
1312100781
1312100776
Warranty Statement
The Company warrants that the Equipment manufactured by it and delivered hereunder shall be free from defects in material and
workmanship for a period of twelve (12) months from the date of initial start-up, or eighteen (18) months from the date of
shipment from the manufacturer, whichever occurs first. The foregoing warranty period shall apply to all Equipment, except for the
following: (A) all two stage reciprocating stationary models are warranted for the earlier of twenty-four (24) months from the date of
initial operation or thirty (30) months from date of shipment from the manufacturer. (B) Replacement parts will be warranted for
three (3) months from the date of shipment from the manufacturer. Should the failure to conform to this warranty be reported in
writing to the Company within said period, the Company shall, at its option, correct such non - conformity by suitable repair to
such Equipment, or furnish a replacement part F.O.B point of shipment, provided that the Purchaser has installed, maintained,
and operated such Equipment in accordance with good industry practices, and has complied with specific recommendations of the
Company. Accessories and equipment furnished by the Company, but manufactured by others, shall carry whatever
warranty the manufacturer conveyed to the Company and which can be passed on to the Purchaser. The Company shall not be
liable for any repairs, replacements, or adjustments to the Equipment, or any costs of labor performed by the Purchaser without the
Company’s prior written approval.
The Company makes no performance warranty unless specifically stated within its proposal, and the effects of corrosion, erosion,
and normal wear and tear are specifically excluded from the Company’s warranty. In the event performance warranties are
expressly included, the Company’s obligation shall be to correct in the manner and for the period of time provided above.
THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND
WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
HEREBY DISCLAIMED. THIS WARRANTY SUPERSEDES ALL PREVIOUS WARRANTY STATEMENTS.
Correction by the Company of non-conformities, whether patent or latent, in the manner and for the period of time provided
above, shall constitute fulfillment of all liabilities of the Company and its distributors for such non-conformities with respect to, or
arising out of such Equipment.
LIMITATION OF LIABILITY
THE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE TOTAL
LIABILITY OF THE COMPANY, ITS DISTRIBUTORS AND SUPPLIERS WITH RESPECT TO CONTRACT OR
THE EQUIPMENT AND SERVICES FURNISHED IN CONNECTION WITH THE PERFORMANCE OR
BREACH THEREOF, OR FROM THE MANUFACTURE, SALE, DELIVERY, INSTALLATION, REPAIR OR
TECHNICAL DIRECTION COVERED OR FURNISHED UNDER CONTRACT, WHETHER BASED ON
CONTRACT, WARRANTY, NEGLIGENCE, INDEMNITY, STRICT LIABILITY OR OTHERWISE, SHALL NOT
EXCEED THE PURCHASE PRICE OF THE EQUIPMENT UPON WHICH SUCH LIABILITY IS BASED.
THE COMPANY, ITS DISTRIBUTORS AND ITS SUPPLIERS SHALL IN NO EVENT BE LIABLE TO THE
PURCHASER, ANY SUCCESSORS IN INTEREST, OR ANY BENEFICIARY OR ASSIGNEE OF THE
CONTRACT FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES
ARISING OUT OF THIS CONTRACT OR ANY BREACH THEREOF, OR ANY DEFECT IN, OR FAILURE OF,
OR MALFUNCTION OF THE EQUIPMENT, WHETHER OR NOT BASED ON LOSS OF USE, LOST PROFITS
OR REVENUE, INTEREST, LOST GOODWILL, WORK STOPPAGE, IMPAIRMENT OF OTHER GOODS, LOSS
BY REASON OF SHUTDOWN OR NON-OPERATION, COST OF PURCHASE OF REPLACEMENT POWER, OR
CLAIMS OF PURCHASER OR CUSTOMERS OF PURCHASER FOR SERVICE INTERRUPTION, WHETHER OR
NOT SUCH LOSS OR DAMAGE IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, INDEMNITY, STRICT
LIABILITY OR OTHERWISE.
Chicago Pneumatic Compressors
1800 Overview Drive
Rock Hill, SC 29730
866-869-3114 (Parts and Technical)
Download PDF