OPERATING INSTRUCTIONS:

FREEDOM 3 DETECTORS

(Coin Commander, CDC, and Plus)

The control panel of the Freedom 3 has four control knobs and a jack for the headphones.

CONTROL FUNCTIONS

Power/Detection Depth Control:

Rotate knob clockwise to turn detector on. Further rotation increases detection depth.

Audio Control: This enables the operator to adjust precisely the threshold level of sound generated by the detector.

Dual Discrimination Controls:

Ferrous Range: This knob (lower) allows adjustment for the elimination of targets in the iron range up to but not including aluminum pulltabs. Targets located and accepted in this range will give an audio increase.

Non-ferrous Range: This knob (upper) allows adjustment for the elimination of targets in the range of pulltabs through aluminum screwcaps. All targets located and accepted in this range will give the coin alert audio signal.

Pinpointing Trigger: This switch under the forward part of the armrest where the “trigger finger” would normally rest selects the electronic zero motion pinpointing mode. Depress and hold this switch for pinpointing.

Headphone Jack:

Located on the control panel.

OPERATING INSTRUCTIONS:

Set controls to INITIAL SETTINGS (∆) positions. By first rotating the controls to these points the detector is turned on and adjusted for satisfactory operation. Setting the audio level is a separate adjustment.

Discrimination:

The Trash Elimination controls permit the selection of targets desired in both ferrous and non-ferrous ranges. The Ferrous control is adjustable from zero through bottlecaps rejection while the Non-ferrous control takes over at pulltab rejection and is adjustable through aluminum screwcaps.

When a metallic object is accepted, the detector’s speaker or earphone sound will increase from the pre-selected audio threshold level. When a metal object is eliminated (rejected), the

sound may decrease or become silent. Some rejected targets will cause the audio to “break up” or sound erratic. .

Searching:

Scan the searchcoil at a rate of about one or two feet per second. Maintain a one to two inch searchcoil height above the ground. Detection of a metal target within the ranges selected will be indicated by an increase in sound for the ferrous range and the coin alert in the non-ferrous range.

Pinpointing:

Precise pinpointing is available with the Pinpointing Trigger.

To use the pinpointing function of the detector to determine the exact location, press the

“trigger switch” and HOLD. The detector will now give a more pronounced signal when the searchcoil is held directly above or criss-crossed over the target.

Even more precise pinpointing can be obtained by placing the searchcoil on the ground, then pressing and HOLDING the switch. Slide the coil, maintaining ground contact across the target.

BATTERIES:

The Freedom 3 requires three (3) 9-volt batteries.

Battery Test:

Each time the detector is turned on the batteries are automatically and audibly checked. Three tones indicate the batteries are very good, two tones and the batteries are adequate. One single tone and it is time to replace the batteries.

Battery Replacement:

Freedom 3 Coin Commander:

The batteries are located beneath the armrest of the Freedom 3 Coin Commander. To replace them, loosen the captive metal knurled screw and remove the cover. Pull the printed circuit board with the two batteries attached from the compartment. (Notice how the wires are positioned). Next, grasp the wires on the left side of the compartment and remove the third battery. Replace the batteries being careful that the wiring follows the batteries back into the compartment.

Be sure the waterproof O-ring seal is properly formed around the ridge on the cover.

Reposition the door and tighten the knurled metal screw. Tighten finger tight only.

Freedom 3 CDC and Plus:

The batteries are located on the side of the chassis of these Freedom 3’s inside the control housing. To reach them disconnect the searchcoil cable and loosen the captive thumbscrew beneath the control housing. Press on the searchcoil connector to loosen the chassis and

carefully slide it out. The batteries are beneath a protective clamp directly behind the control panel. Loosen the screw holding it and slide the clamp off to allow removal of the batteries.

MAINTENANCE

™ Always remember that your detector is a sensitive electronic instrument. It is built to withstand rugged treatment in the outdoors. Use your Garrett detector to the fullest extent possible, and never feel that you have to baby it. Yet, always protect the detector and handle it with reasonable care.

™ Try to avoid temperature extremes as much as possible, such as storing the detector in an automobile trunk during hot summer months or outdoors in sub-freezing weather.

™ Keep you detector clean. Always wipe the housing after use, and wash the coil when necessary. Protect your instrument from dust and sand as much as possible.

™ Your searchcoil is submersible. The control housing is not! Never submerge the control housing and always protect it from heavy mist, rain or blowing surf.

™ Disassemble the stem and wipe it clean after use in sandy areas.

™ When storing longer that about one month, remove batteries from the detector.

REPAIR SERVICE

™ In case of difficulty, read this Owner’s Manual again thoroughly to make certain your detector is not inoperable needlessly. Your dealer may also be able to offer advice.

™ When your detector must be returned to the factory for service, always include a letter that describes its problem as fully as possible. Before you return your detector to the Garrett factory, make certain:

™ You have checked batteries, switches and connectors. (Check batteries especially closely.

They are the most common cause of detector “failure”.)

™ You have checked with your dealer, particularly if you are not familiar with this type detector.

™ You have included a note with the detector describing the problems you are encountering with this detector and conditions under which they occur. Make certain to include your name, address and a phone number where you can be contacted between 8:30 a.m. and 4 p.m., Central Time.

™ You have carefully packed the detector in its original shipping carton or other suitable box.

Make certain that proper insulation or packing material is used to keep all parts secure. Do not ship stems or headphones unless they are part of the problem. Be certain to return all coils.

™ Ship to Garrett Metal Detectors, 1881 W. State St., Garland, TX 75042.

™ You can call Garrett’s Customer Service Department (800-527-4011) if you have further questions.

™ Please allow approximately one week for Garrett technicians to examine and repair your detector after they receive it, plus another week for return shipping to you. All equipment will be returned UPS or parcel post unless written authorization is given by you to ship collect by air parcel post, UPS Blue (air) or air freight.

MIND YOUR MANNERS

Filling holes and obeying no trespassing signs are but two requirements of a dedicated metal detector hobbyist. A sincere request that Charles Garrett makes to every user of one of his detectors is that each place searched be left in a better condition than it was found.

Thousands of individuals and organizations have adopted this formal Metal Detector Operators

Code of Ethics:

™ I will respect private and public property, all historical and archaeological sites and will do no metal detecting on these lands without proper permission.

™ I will keep informed on and obey all laws, regulations and rules governing federal, state and local public lands.

™ I will aid law enforcement officials whenever possible.

™ I will cause no willful damage to property of any kind, including fence, signs and buildings and will always fill holes I dig.

™ I will not destroy property, buildings or the remains of ghost towns and other deserted structures.

™ I will not leave litter or uncovered items lying around. I will carry all trash and dug targets with me when I leave each search area.

™ I will observe the Golden Rule, using good outdoor manners and conducting myself at all times in a manner which will add to the stature and public image of all people engaged in the field of metal detection.

WARNING!

Any metal detector may discover underground power lines, explosives or other items which when struck could cause personal injury. When searching for treasure with your detector, observe these precautions:

™ Do not hunt in an area where you believe there may be shallowly buried underground electric lines or pipes.

™ Do not hunt in a military zone where bombs or other explosives may be buried.

™ Avoid striking any line known to be or suspected to be carrying electrical power.

™ Do not disturb any pipeline, particularly if it could be carrying flammable gas or liquid.

™ Use reasonable caution in digging toward any target, particularly in areas where you are uncertain of underground conditions.

PATENT PROTECTION: Proof of Garrett excellence is the recognition given them by the following

United States patents: 4,709,213; 4,488,115; 4,700,139; 4,398,104; 4,423,377; 4,303,879; 4,334,191;

3,662,255; 4,162,969; 4,334,192; 5,148,151; 5,138,262; 5,721,489; 5,786,696; 5,969,528; Design

274,704 and 297,221; Design 333,990; G.B. Design 2,011,852; Australia Design 111,674 and other patents pending