Avanti WCR683DZD-1 Instruction manual

Add to My manuals
20 Pages

advertisement

Avanti WCR683DZD-1 Instruction manual | Manualzz

BUILT-IN DUAL ZONE WINE CHILLER / VINERA CON 2 ZONAS

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

Model Number / No. de Modelo:

WCR683DZD-1

(Picture may vary)

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING

INSTRUCTIONS.

La sección en español empieza en la página 16.

Avanti Products has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice.

Avanti Products, A Division of The Mackle Co., Inc.

P.O. Box 520604 - Miami, Florida 33152 www.avantiproducts.com

TABLE OF CONTENTS

Appliance Safety

Important Safeguides

Help Us Help You …

Parts and Features

Important Safety Instructions

Installation Instructions

Before Using Your Wine Chiller

Installation of Your Wine Chiller

Electrical Connection

Extension Cord

Reversing the Door Swing of Your Wine Appliance

Installing Stainless Steel Handle

Operating Your Wine Chiller

ON/OFF Power

Setting the Temperature Control

Storage

Interior Light

Door Lock

Shelves

Care and Maintenance

Cleaning Your Wine Chiller

Power Failure

Moving Your Wine Chiller

Energy Saving Tips

Troubleshooting Guide

Service for Your Appliance

Wiring Diagram

Your Avanti Products Warranty

Instrucciones en Español

Registration Information and Registration Card

2

13

14

14

15

16 ~ 18

19

12

12

12

12

11

11

11

12

9

10

10

10

8

9

8

8

7

7

7

7

5

6

3

4

APPLIANCE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that

can kill or injure you and others. All safety messages will follow the Safety

Alert Symbol and either the words “DANGER”, “WARNING” or “CAUTION”.

Danger means that failure to heed this safety statement may result in severe personal injury or death.

Warning means that failure to heed this safety statement may result in extensive product damage, serious personal injury, or death.

Caution means that failure to heed this safety statement may result in minor or moderate personal injury, or property or equipment damage.

All safety messages will alert you do what the potential hazard is, tell you how to reduce the chance of injury, and let you know what can happen if the instructions are not followed.

3

IMPORTANT SAFEGUIDES

Before the appliance is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precaution, including the following:

 Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an extension cord.

 Replace all panels before operating.

 It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles that cannot be turned off by a switch or pull chain.

 Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.

 Before proceeding with cleaning and maintenance operations, make sure the power line of the unit is disconnected.

 Do not connect or disconnect the electric plug when your hands are wet.

 Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in electrical shock or death.

 Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this material. All other servicing should be referred to a qualified technician.

FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

 Use two or more people to move and install appliance. Failure to do so can result in back or other injury.

 To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed. Choose a well-ventilated area with temperatures above 60°F (16°C) and below

90°F (32°C). This unit must be installed in an area protected from the element, such as wind, rain, water spray or drips.

 The appliance should not be located next to ovens, grills or other sources of high heat.

 The appliance must be installed with all electrical connections in accordance with state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in accordance with the National Electrical Code and local codes and ordinances is required.

 Do not kink or pinch the power supply cord of appliance.

 The fuse (or circuit breaker) size should be 15 amperes.

 It is important for the appliance to be leveled in order to work properly. You may need to make several adjustments to level it.

 Never allow children to operate, play with or crawl inside the appliance.

 Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may damage or discolor the interior.

 Do not use this apparatus for other than its intended purpose.

4

HELP US HELP YOU...

Read this guide carefully.

It is intended to help you operate and maintain your new Wine Chiller properly.

Keep it handy to answer your questions.

If you don't understand something or you need more assistance, please call:

Avanti Customer Service

800-220-5570

Keep proof of original purchase date (such as your sales slip) with this guide to establish the warranty period.

CAUTION:

THIS WINE CHILLER IS NOT

DESIGNED FOR THE STORAGE

OF MEDICINE OR OTHER

MEDICAL PRODUCTS.

Write down the model and serial numbers.

You'll find them on a plate located on the rear outside wall of the Wine Chiller.

Please write these numbers here:

____________________________________

Date of Purchase

____________________________________

Model Number

____________________________________

Serial Number

Use these numbers in any correspondence or service calls concerning your Wine Chiller.

If you received a damaged Wine Chiller, immediately contact the dealer (or builder) that sold you the Wine Chiller.

Save time and money. Before you call for service, check the Troubleshooting Guide. It lists causes of minor operating problems that you can correct yourself.

IF YOU NEED SERVICE

We're proud of our service and want you to be pleased. If for some reason you are not happy with the service you receive, here are some steps to follow for further assistance.

FIRST, contact the people who serviced your

NEXT, if you are still not pleased, write all the details, including your telephone number, and send it to:

Wine Chiller. Explain why you are not pleased.

In most cases, this will solve the problem.

Avanti Products

10880 NW 30 Street

Miami, FL 33172 USA

5

PARTS & FEATURES

3

4

5

Stainless Steel Door Frame

Burgundy Bottle Shelves (Roll-out)

Total 6

Standard Bottle Shelves (Roll-out)

Total 7

8

9

Small Standard Bottle Shelf (Roll-out)

Total 1

Small Standard Bottle Shelf – Total 1

12 Cabinet

(Not shown – See page 12)

6

IMPORTANT SAFETY INSTRUCTIONS

WARNING

 To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions:

 Read all instructions before using the Wine Chiller.

DANGER or WARNING: Risk of child entrapment.

Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are still dangerous . . . even if they will “just sit in the garage a few days”.

Before you throw away your old Wine Chiller: Take off the door. Leave the shelves in place so that children may not easily climb inside.

 Never allow children to operate, play with, or crawl inside the appliance.

 Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or explosion.

 Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.

-Save these instructions-

INSTALLATION INSTRUCTIONS

BEFORE USING YOUR WINE CHILLER

 Remove the exterior and interior packing. Read the Installer’s Directions.

 Check to be sure you have all of the following parts:

 6 Burgundy Bottle Shelves

 7 Standard Bottle Shelves

 1 Small Bottom Shelf

 1 Stainless Steel Handle Assembly with 2 Screws, 2 Flat Washers and 2 Lock Washers

 1 Door Lower Hinge Bracket for Door Opening from the Right Side

 1 Instruction Manual

 Before connecting the Wine Chiller to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.

 Clean the interior surface with lukewarm water using a soft cloth.

 Install the handle on the left side of the door.

INSTALLATION OF YOUR WINE CHILLER

 This appliance is designed to be for free standing installation.

 Allow 5 inches of space between the back and sides of the unit, which allows the proper air circulation to cool the compressor and condenser..

 Place your Wine Chiller on a floor that is strong enough to support it when it is fully loaded. To level your Wine Chiller, adjust the front leveling legs at the bottom of the Wine Chiller.

 Locate the Wine Chiller away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly.

 Avoid locating the unit in moist areas.

 Plug the Wine Chiller into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an

7

authorized Avanti Products service center.

ELECTRICAL CONNECTION

Warning

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center.

This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power cord supplied.

For personal safety, this appliance must be properly grounded.

This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury.

The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the appliance, be careful not to damage the power cord.

 EXTENSION CORD

Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this appliance. However, if you must use an extension cord it is absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.

REVERSING THE DOOR SWING OF YOUR APPLIANCE

This appliance has the capability of the door opening from either the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please call service for reversal instructions.

8

INSTALLING STAINLESS STEEL HANDLE

This wine chiller includes a stainless steel handle that is not required to operate this unit. To install the handle please follow the below instructions:

1. Pull away the door gasket in the area where the handle is to be installed on the left side as shown below in Illustration # 1. The gasket is easily displaced by hand, no tools are necessary.

2. Using a Flat head screwdriver remove the two (2) pre-installed decorative plugs from the backside of the door as shown below in Illustration #1. Save the decorative plugs for future use.

3. Insert the two (2) Phillips head handle screws with the lock washers and flat washers attached through the gasket side of the door frame until the screws pass through the door frame. Follow the sequence shown below in Illustration # 2.

4. Align the handle with the screws installed in the above step # 3. Tighten the screws using a

Phillips head screwdriver until the handle sets both flush and secured tightly against the door frame. (DO NOT overtighten as this will cause damage to the handle assembly).

5. Replace the door gasket to its original position.

Decorative Screw Phillips Head Screw

Flat Washer

S/S Handle

Gasket

Lock Washer

OPERATING YOUR WINE CHILLER

It is recommended you install the Wine Chiller in a place where the ambient temperature is between

72-78 degrees Fahrenheit. If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate. The range of 40-65 degrees

Fahrenheit may not be reached.

Recommended Temperatures for Chilling Wine .

Red Wines 15º - 18º C 58 – 65º F

Dry/White Wines 9º - 14º C 48 – 57º F

Rose Wines 10º - 11º C 49 – 51º F

Sparkling Wines 5º - 8º C 40 – 47º F

9

The LED readout will show the original temperature set previously (the preset temperature at the factory for UPPER ZONE is 50ºF and for LOWER ZONE is 60ºF).

You can select temperature display setting from Fahrenheit to Celsius degree by pushing the ºF/ºC button/mark. Fahrenheit or Celsius degrees indicator will appear in blue color in the temperature display window for each zone.

ON/OFF POWER

To turn ON or OFF the appliance, press the button/mark and hold for 2 seconds.

SETTING THE TEMPERATURE CONTROL

You can press the left side UP and DOWN buttons/marks to control the internal temperature of the upper zone and press the right side UP and DOWN buttons/marks to control the internal temperature of the lower zone.

The degrees indicators will appear in the display window marked UPPER ZONE and LOWER ZONE.

The temperature range of LOWER ZONE is 55 ~ 65 ºF which is suitable for storing white and red wines. The temperature range of UPPER ZONE is 40 ~ 55ºF which is suitable for storing sparkling and white wines.

 The temperature that you desire to set will increase 1ºF or 1ºC if you push the UP button/mark once, on the contrary the temperature will decrease 1ºF or 1ºC if you push the DOWN button/mark once.

 When you store mostly red wines, you should store them in the LOWER ZONE, the temperature which you control by pushing the above UP and DOWN buttons/marks need to be set at between

58 to 65  F and the red LED lamp under “RED” marking will be lit

 When you store mostly white wines, you can store them in the UPPER ZONE or LOWER ZONE.

When you use the LOWER ZONE, the temperature can be set at between 55 to 57  F and the green LED lamp under “WHITE” marking will be lit. When you use the UPPER ZONE, the temperature can be set at between 48 to 55  F and the green LED lamp under “WHITE” marking will be lit.

 When you store mostly sparkling wines, you should store them in the UPPER ZONE, the temperature needs to be set at between 40 to 47  F and the yellow LED lamp under “SPARKL” marking will be lit.

NOTE:

 If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes before restarting the unit. If you attempt to restart before this time delay, the Wine Chiller will not start.

 When you use the wine chiller for the first time or restart the wine chiller after having been shut off for a long time, there could be a few degrees variance between the temperature you select and the one indicated on the LED readout. This is normal and it is due to the length of the activation time. Once the wine chiller is running for a few hours everything will be back to normal.

STORAGE

Many bottles may differ in size and dimensions. As such the actual number of bottles you may be able to store may vary.

NOTE: You can place 74 standard bottles in the upper zone and 75 standard bottles in the lower zone.

10

Bottle capacities are approximate maximums when storing traditional Bordeaux 750 ML bottles and include bulk storage.

INTERIOR LIGHT

 Interior lights are available in both upper and lower zones.

 You can turn the interior light on in each zone by pushing the button marked with the “bulb” symbol or touch the mark .

 The lights will turn off automatically if it remains ON for 10 minutes or more. You have to push the button marked with the “bulb” symbol back on.

or touch the mark

DOOR LOCK

Your unit is provided with a lock and key combination.

again and the light will turn

The keys are located inside the plastic bag that contains the User’s Guide. Insert the key into the lock and turn it counterclockwise to unlock the door. To lock the door do the reverse operation making sure metal pin is engaged completely. Remove the key and place it in a secure place for safekeeping.

SHELVES

This appliance is equipped with a pull-out roller assembly (except for the bottom shelf) and you can move the wooden shelves out and in smoothly.

Pull-out Roller Shelves

To prevent damaging the door gasket, make sure to have the door all the way opened when pulling shelves out of the rail compartment.

 For easy access to the bottles, you must pull the shelves approximately 1/3 out of the rail compartment.

 To remove the shelves out of the rail pull each shelf approximately 1/3 out. Use a long flat screwdriver to press down the right plastic notch as shown in Figure A and at the same time lift the left plastic notch as shown in Figure B. Then proceed to pull out the shelf slowly. Contact our service department if assistance is needed.

Figure A Figure B

11

CARE AND MAINTENANCE

CLEANING YOUR WINE CHILLER

 Turn off the power, unplug the appliance, and remove all items including shelves.

 Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water.

 Wash the shelves with a mild detergent solution.

 Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts.

 Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with a clean soft cloth.

 Do not use steel wool or steel brush on the stainless steel. These will contaminate the stainless steel with steel particles and rusting may occur.

POWER FAILURE

 Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need to take the proper steps to protect your contents.

MOVING YOUR WINE CHILLER

 Remove all items.

 Securely tape down all loose items (shelves) inside your appliance.

 Turn the adjustable legs up to the base to avoid damage.

 Tape the door shut.

 Be sure the appliance stays secure in the upright position during transportation. Also protect outside of appliance with a blanket, or similar item.

ENERGY SAVING TIPS

 The Wine Chiller should be located in the coolest area of the room, away from heat producing appliances, and out of the direct sunlight.

CHARCOAL FILTRATION SYSTEM

Your cellar is equipped with an active charcoal filtration system to ensure air purity, cooling efficiency, and to maintain an odor free cabinet for the storage of your fine wines. The filter assembly is located at the bottom of the rear panel inside your cellar. Keep in mind, that this filter must be changed every 12 months .

To replace your filter:

1 Remove the bottles of wine stored on the two (2) bottom shelves

2 Remove the shelves and set aside to be replaced once you have changed the filter

3 Grasping the filter from both the top and bottom edges, pull toward you and remove the entire filter assembly cover.

4 Remove the existing filter and replace with a new one.

5 Replace the filter assembly cover by pressing it against the assembly until you hear a “click” sound.

12

PROBLEMS WITH YOUR WINE CHILLER?

You can solve many common Wine Chiller problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer.

TROUBLESHOOTING GUIDE

Wine Chiller does not operate.

Wine Chiller is not cold enough.

Turns on and off frequently.

Not plugged in.

The appliance is turned off.

The circuit breaker tripped or a blown fuse.

Check the temperature control setting.

External environment may require a higher setting.

The door is opened too often.

The door is not closed completely.

The door gasket does not seal properly.

The room temperature is hotter than normal.

A large amount of contents has been added to the wine chiller.

The door is opened too often.

The door is not closed completely.

The temperature control is not set correctly.

The door gasket does not seal properly.

The light does not work. Not plugged in.

The circuit breaker tripped or a blown fuse.

The light button is “OFF”.

Vibrations. Check to assure that the Wine Chiller is level.

The Wine Chiller seems to make too much noise. The rattling noise may come from the flow of the refrigerant, which is normal.

As each cycle ends, you may hear gurgling

The door will not close properly. sounds caused by the flow of refrigerant in your

Wine Chiller.

Contraction and expansion of the inside walls may cause popping and crackling noises.

The Wine Chiller is not level.

The Wine Chiller is not level.

The door was reversed and not properly installed.

The gasket is dirty.

The shelves are out of position.

13

SERVICE FOR YOUR WINE CHILLER

We are proud of our customer service organization and the network of professional service technicians that provide service on your Avanti appliances. With the purchase of your Avanti appliance, you can have the confidence that if you ever need additional information or assistance, the

Avanti Products Customer Service team will be here for you. Just call us toll-free.

Product Information

800-323-5029

Part Orders

800-220-5570

In-Home Repair Service

800-220-5570

AVANTI PRODUCTS CUSTOMER SERVICES

Whatever your questions are about our products, help is available.

You may order parts and accessories that will be delivered directly to your home by personal check, money order, Master Card, or Visa.

An Avanti Products authorized service center will provide expert repair service, scheduled at a time that is convenient for you. Our trained servicers know your appliance inside and out.

WIRING DIAGRAM

14

YOUR Avanti Products WARRANTY

WHAT IS COVERED

WARRANTY

For one year from the date of purchase by the original owner, Avanti

Products will, at its option, repair or replace any part of the unit, which proves to be defective in material or workmanship under normal use.

During this period Avanti Products will provide all parts and labor necessary to correct such defects free of charge, so long as the unit has been installed and operated in accordance with the written instructions in this manual.

Avanti Products will provide you with a reasonably similar replacement product that is either new or factory refurbished. In rental or commercial use, the warranty period is 90 days.

All Avanti Appliances of 3.5 cubic feet capacity or less must be brought/sent to the appliance service shop for repair.

Staple your sales receipt here. Proof of original purchase date is needed to obtain service under warranty.

LIMITED SECOND THROUGH

FIFTH YEAR WARRANTY

For the second through the fifth year from date of original purchase, Avanti Products will provide a replacement compressor free of charge due to a failure. You are responsible for the service labor and freight charges. In rental or commercial use, the limited compressor warranty is one year and nine months. Cost to move the appliance to the servicers’ shop and back to the user's home, as may be required, are the user's responsibility.

WHAT IS NOT COVERED

 Content losses of food or other, due to spoilage.

 Incidental or consequential damages.

 Parts and labor costs for the following will not be considered as warranty:

 Door springs, and/or frames.

 Inner door panels, door rails and/or door supports.

 Light bulbs and/or plastic housing.

 Punctured evaporator that voids the warranty on the complete sealed system.

 Repairs performed by unauthorized servicers.

 Shipping and handling costs associated with the replacement of the unit.

 Service calls that do not involve defects in material or workmanship such as customer education, door reversal, or proper installation.

 Service calls that are related to external problems, such as abuse, misuse, inadequate electrical power, accidents, fire, floods, or acts of God.

 Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage expenses for service calls to remote areas, including the State of

Alaska.

 Replacement of house fuses or resetting circuit breakers.

 Failure of the product if it is used for other than its intended purpose.

 This warranty does not apply outside the

Continental USA.

15

INSTRUCCIONES DE SEGURIDAD

ATENCION

INSTRUCCIONES PARA

LA CONEXION A TIERRA

Este aparato electrodoméstico debe estar conectado a tierra. En caso de un cortocircuito eléctrico, la conexión a tierra reduce el riesgo de choque eléctrico proporcionando un cable a tierra con una enchufe de conexión a tierra. Este enchufe debe estar conectado en un tomacorriente instalado correctamente y conectado a tierra.

ADVERTENCIA

– El uso inadecuado del enchufe de conexión a tierra puede resultar en un riesgo de choque eléctrico. Consulte con un electricista o persona de reparaciones competente si no comprenden bien las instrucciones de conexión a tierra o si existe alguna duda sobre si el aparato esta conectado a tierra correctamente.

NO USE UN CORDON DE

PROLONGACION ELECTRICA

Use un tomacorriente de pared exclusivo. No conecte su vinera a cordones de prolongación eléctrica o junto a cualquier otro electrodoméstico en el mismo tomacorriente de pared.

ADVERTENCIA IMPORTANTE:

Una vinera vacía es una atracción muy peligrosa para los niños. Saque todas las juntas, pestillos, tapas o puerta de todo electrodoméstico que no esté en uso, o tome alguna medida para asegurar que no presente peligro.

INSTRUCCIONES DE INSTALACION

Saque los embalajes exteriores, limpie bien el exterior con un paño suave seco, y el interior con un paño húmedo y tibio. Evite colocar la vinera cerca de una fuente de calor, luz de sol directa, o lugar húmedo.

UBICACION

1. Seleccione un lugar con su piso fuerte y nivelado.

2. Evite la luz directa del sol o calor. La luz directa del sol puede afectar la capa de acrílico.

Las fuentes de calor en su proximidad provocarán un consumo mayor de electricidad.

OPERACION

Para evitar vibraciones, el compartimiento interior debe estar bien nivelado. La temperatura variará dependiendo de la cantidad de botellas almacenadas y la frecuencia con que se abre la puerta.

Cuando la vinera no se use por un período largo, desconecte el enchufe y deje la puerta entreabierta.

Nota: Espere entre 3 a 5 minutos antes de volver a encender si el funcionamiento ha sido interrumpido.

Se recomienda que Ud coloque su vinera en un lugar donde la temperatura ambiental se mantenga entre 23-25 grados centígrados.

Si la temperatura ambiental oscila afuera de esos límites, pueda afectar la temperatura de la caja.

Por ejemplo, si su unidad está situada en lugares donde hay temperaturas muy frías o calientes también puede afectar la temperatura de la caja.

16

Temperaturas recomendadas para enfriar vinos:

Vinos tintos: 58 - 65ºF (14-18ºC)

Vinos blanco/seco: 48 - 57ºF (9-14ºC)

Vinos rosé/Zinfandel: 49 - 51ºF (9-11ºC)

Vinos espumantes: 40 - 47ºF (4- 8ºC)

Para encender el electrodoméstico, oprima el botón marcado “ ” por 2 segundos.

En la fábrica se programa la zona superior a los 50ºF (10ºC).

La zona inferior se programa a los 60ºF (16ºC).

Ud puede cambiar de grados Centígrados a Fahrenheit o viceversa, oprimiendo el boton marcado

ºF/C. En la pantalla digital para cada zona aparecerán los grados en color azul.

OPERACION

Oprima los botones marcado “ “ y “ “ localizados en el lado izquierdo del panel de controles para programar la temperatura interna de la zona superior. Repita esa operación pero con los botones localizados en el lado derecho para programar la temperatura interna de la zona inferior.

La pantalla mostrará los grados respectivamente para cada zona en color rojo. La temperatura en la zona inferior varía entre 55~65ºF (13~18ºC) y es la indicada para los vinos rojos o blancos.

La temperatura en la zona superior varia entre 40~55ºF (5~13ºC) y es la indicada para los vinos blancos o espumosos.

Al presionar los botones marcados “ “ o “ “ por primera vez, el indicador en la pantalla mostrará la temperatura programada de fábrica o la más reciente.

Oprima el botón marcado ( ) una vez y la temperatura aumentará un grado. Si Ud oprime el botón marcado ( ) una vez la temperatura bajará un grado.

Si en su mayoría Usted solamente guarda vinos rojos, debe colocarlos en la zona inferior.

El indicador marcado (RED) se alumbrará en color rojo. Ud necesita programar esa temperatura entre los 58~65ºF (15~18ºC).

Si Ud solamente guarda vinos blancos, usted puede colocarlos en cualquier zona pero tendrá que mantener una temperatura entre 55~57ºF (13~14ºC) en la zona inferior y una temperatura de

48~55ºF (9~13ºC) en la zona superior.

El indicador marcado “WHITE” se alumbrará en color verde.

Cuando Ud guarda vinos espumosos, deberá colocar las botellas en la zona superior y marcar la temperatura entre los 40~47ºF (5~8ºC).

El indicador marcado “SPARKL” se alumbrará en color amarillo.

LUZ INTERIOR

La luz interior para cada zona se controla manualmente y no funciona al abrir ni cerrar la puerta.

Para prender o apagár la luz, presione el botón marcado ( ) de la luz ubicado en el panel de control. Si la luz está prendida, por más de 10 minutos, se apagará automáticamente.

CERRADURA DE LA PUERTA

Su unidad viene equipada con una combinación de cerradura y llave.

Las llaves (2) están dentro de la bolsa plástica junto al manual de instrucciones.

Introduzca la llave en la cerradura y gírela hacia la izquierda para abrir la puerta.

Para cerrarla, gire la llave hacia la derecha.

Quite la llave y colóquela en un lugar seguro para evitar que se pierda.

17

COMO INSTALAR LA MANIJA

Su nevera viene equipada con una manija de acero inoxidable que no es necesario instalar para operar la unidad.

Para instalarla, remueva los tornillos decorativos del frente de la puerta.

Coloque la manija en su lugar designado utilizando los tornillos Phillips incluídos en la bolsa.

Apriete los tornillos utilizando un destornillador Phillips (+).

DESCONGELACION

Su refrigerador para vinos ha sido diseñado con un sistema de descongelación de “ciclo automático”.

Las superficies refrigeradas del compartimiento para vinos se descongela automáticamente, durante el ciclo “apagado” del control de enfriamiento (termostato). El agua descongelada del compartimiento es eliminada automáticamente, encauzándola hacia una bandeja de goteo ubicado en el compresor.

La transferencia de calor del compresor evapora el agua.

ADVERTENCIA

Asegúrese de tener la puerta abierta completamente se Ud desea remover los estantes de madera o moverlos hacia adelante para extraer una botella.

NOTA:

Para remover los estantes de madera corredizos, mueva cada uno de ellos aproximadamente una tercera parte fuera de los raíles.

Presione el lado plástico derecho usando un destornillador plano (siga la flecha) como se muestra en el dibujo “A” de la página 14 y a la misma vez haga lo mismo con el plástico del lado izquierdo como se muestra en el dibujo “B” de la página 14.

Saque el estante corredizo suavemente.

CUIDADO Y MANTENIMIENTO

LIMPIEZA

Para limpiar el interior, use un paño suave con una solución de una cucharada de bicarbonato de sodio por cada cuarto de agua, o una solución de espuma de jabón suave, o un detergente suave.

Para lavar las rejillas, sáquelas deslizándolas con cuidado, y use una solución de detergente suave; luego séquelas con un paño suave. Limpie el exterior con un paño húmedo suave y un poco de detergente suave o productos de limpieza para electrodomésticos.

CORTE DE CORRIENTE

La mayoría de los cortes de corriente se corrigen en una o dos horas y no afectarán las temperaturas de su vinera. Sin embargo, Ud. deberá reducir la cantidad de veces que abra la puerta cuando la corriente esté apagada.

SI UD. SE MUDA

Saque o asegure todos los artículos dentro de su vinera. Para evitar que los tornillos nivelantes se averíen, gírelos completamente hacia la base.

18

REGISTRATION INFORMATION

Thank you for purchasing this fine Avanti products. Please fill out this form and return it within 100 days of purchase and receive these important benefits to the following address:

Avanti Products, A Division of The Mackle Co., Inc.

P.O. Box 520604 - Miami, Florida 33152 USA

Protect your product:

We will keep the model number and date of purchase of your new Avanti Products product on file to help you refer to this information in the event of an insurance claim such as fire or theft.

Promote better products:

We value your input. Your responses will help us develop products designed to best meet your future needs.

----------------------------------------------------------(detach here)----------------------------------------------------------

Avanti Registration Form

__________________________________ _____________________________________

Name Model # Serial #

__________________________________ _____________________________________

__________________________________ ______________________________________

__________________________________

Area Code Phone Number

As Your Primary Residence, Do You:

 Own  Rent

Did You Purchase An Additional Warranty: Your Age:

 Extended  Food Loss None

Reason For Choosing This Avanti Product:

Please indicate the most important factors

 under 18 18-25 26-30

 31-35 36-50 over 50

Marital Status: that influenced your decision to purchase this

 Price

 Married  Single

Is This Product Used In The:

 Business

 Product Features

 Avanti Products Reputation

 Product Quality

 Salesperson Recommendation

 Friend/Relative Recommendation

How Did You Learn About This Product:

Advertising

In Store Demo  Personal Demo

 Other_______________________________

Comments____________________________

 Warranty

 Other_______________________ _____________________________________

19

20

PRINTED IN CHINA

advertisement

Related manuals

advertisement

Languages