CrimeStopper | RS-1604.DP.TW1 | Operating instructions | CrimeStopper RS-1604.DP.TW1 Operating instructions

RS-1604TW1/RS-1704TW2/RS-1804FM
RS1905FM
2-Way Paging Remote Engine Starting & Keyless
Entry System with 1-Way Sidekick Remote Control
OPERATING INSTRUCTIONS
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote
Start connections, Flashing lights, Brake Reset. For programming, the hood pin and program button are required.
-OPTIONAL: These are features are to be connected only if desired or agreed upon by the customer and the
installing dealer i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc. These features
may also require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is
going to be installed with your particular system.
TECHNICAL SUPPORT: (800) 998-6880
Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: email@crimestopper.com
CRIMESTOPPERSECURITYPRODUCTS,INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV C – 09.30.2005
This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may be received, including interference that
may cause undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by
unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.
TABLE OF CONTENTS
Operation Cautions & Warnings….………………..….…………………………………….…………………...………2
2-Way Paging LED Remote TW1.........…………………………………………………………….…………..……….3
2-Way Paging LCD Remote TW2..……………………………………………………………………………...……….4
2-Way Paging LCD Remote FM…..……..……………………………………………………………………...…...…..5
Using the Remote 1-Way Remote………………………………………………………………………………….….6-7
Remote Engine Starting…………………………………………………………………………………………...…..8-11
Turbo Timer Mode……………………………….……………………………………...………………………….….…12
ConvenienceandSafetyFeatures…….……………………….………………..………………………..….....….13-14
TransmitterProgramming….…………….………………………………………….……………….…..…….…......…15
2Vehicle Operation.………………………………….………………...……………………..………...……..…...……16
Troubleshooting“BeforeYouCall”………….…………..………………………………………….………….…...17-18
Low Battery Warning and replacing the AAA batteryonLCDRemote…………………………………………….19
Setting the Clock…………………………………………………………………………………...………...…Back Page
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shallnot be liable for any accident resulting
from the use of this equipment. This system is designed to be professionally installed into a car or vehicle in which
all items, such as parking brake and all associated components, door switches, transmission shift linkage, throttle
linkage, and all engine safety features, are in perfect working condition.
DO NOT install the Remote Engine Starting System on MANUAL TRANSMISSION vehicles. If accidentally left
in gear the vehicle could become a self-propelled threat to life and property.
IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system
and its safety features. B) Check for proper operation of the system prior to accepting delivery of the vehicle from
the installation facility. C) Check and maintain the condition of the vehicle and all items relative to the proper
operation of this system and its safety features. D) Always leave the doors and windows closed and locked to
protect against accident and theft.
DO NOT remote s tart the vehicle in a closed garage. Make sure that the garage door is open or there is
adequate ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide
fumes.
2
2-WAY PAGING LED REMOTE
RS-1604TW1
OPERATION:
FIXED
ANTENNA
BUTTON 1 (Lock Symbol):
• Press and release to Lock doors.
• Press and Hold for more than 3 seconds to activate
“Panic” feature.
PAGING
LED's
BUTTON 2 (Unlock Symbol):
• Press and release to Unlock doors.
#1
LOCK
BUTTON 3 (Trunk Symbol):
• Press and Hold for two seconds to activate trunk pop
(Optional Feature).
#2
UNLOCK
#5
2 CAR
nd
BUTTON 4 (Start):
• Press and Hold for two seconds to Start/Stop Engine
BUTTON 5 (Side button)
§ Press and Release to show the previous status.
§ Press and Hold for 5 second to switch to vehicle #2.
#3
TRUNK
POP
#4
REMOTE
START
TWO-WAY PAGER OPERATION & PAGE TONES:
FEATURE
LOCK
UNLOCK
AUX #1
REMOTE START
ENGINE RUNNING
TURN OFF ENGINE
PANIC
BUTTON
#1 (Lock)
#2 (Unlock)
#3 (Trunk)
#4 (Start)
ACTION
Press & Release
Press & Release
Press & Hold 2 Sec.
Press & Hold 2 Sec.
#4 (Start)
#1 (Lock)
Press & Hold 2 Sec.
Press & Hold 3 Sec.
3
BEEPS
1X then 1X again
1X then 2X again
1X then 3X again
1X then 3X again
6X
1X
1X then 2X / 12X
LED/FLASH
Orange / 1X
Green / 2X
Yellow / 1X
Blue /3X
Blue / 6X
No Page back
Orange 12X / Green 1X
2-WAY PAGING LCD REMOTE
RS-1704TW2
OPERATION:
BUTTON 1 (LOCK Symbol):
• Press and release to Lock doors.
• Press and Hold for more than 3 seconds to activate “Panic”
feature.
BUTTON 2 (Unlock Symbol):
• Press and release to Unlock doors.
BUTTON 3 (Trunk Symbol):
• Press and Hold two seconds to activate trunk pop (Optional
Feature).
BUTTON 4 (Start Key Symbol):
• Press and Hold two seconds to Start/Stop engine.
BUTTON 5 (On side of remote):
• Press and release to light up the LCD screen.
• Press and release twice to recall the last message from the
LCD screen.
• Press and Hold two seconds to change from Car 1 to Car 2
• Press 5 times to change the time and enable/disable beep
tones from the remote.
LOCK
UNLOCK
TRUNK POP
FIXED
ANTENNA
#2 UNLOCK
#1 LOCK
AM
#5 RECALL
CAR I or II
#3 TRUNK
REMOTE
START
4
LOW BATTERY
LCD
SCREEN
#4 ENGINE
START/STOP
PANIC
RS-1804FM/1905FM
2-WAY PAGING LCD REMOTE
OPERATION:
BUTTON 1 (Lock Symbol):
• Press and release to Lock system.
Press and Hold for more than 3 seconds to activate
“Panic” feature.
FIXED
ANTENNA
BUTTON 2 (Unlock Symbol):
• Press and release to Unlock system.
LCD
SCREEN
PM
BUTTON 3 (Trunk Symbol):
• Press and Release to activate trunk pop (Optional
Feature).
#5
RECALL /
CAR I OR II
#2 DISARM/
UNLOCK
BUTTON 4 (Start Symbol):
• Press and release to Start/Stop Engine.
#1 ARM/
LOCK
BUTTON 5 (On Side of Remote)
• Press and release to recall the last message from the
LCD screen.
• Press and Hold 5 seconds to change from Car 1 to Car 2.
• Press 5 times to enable/disable beep tones from the
remote.
#4 ENGINE
START/STOP
START
#3 TRUNK
POP
IGN
IGN
(<<<< MOVING <<<<<)
PM
PM
LOCK
PM
UnLock
PM
Trunk Pop
5
Confirm Remote
Start Request
PM
Successful Start
USING THE 1-WAY REMOTE
OPERATION:
BUTTON 1 (Lock Symbol):
• Press and release to Lock doors.
• Press and Hold for more than 3 seconds to
activate “Panic” feature.
BUTTON 2 (Unlock Symbol):
• Press and release to Unlock doors.
BUTTON 3 (Trunk Symbol):
• Press and Hold for two seconds to activate
trunk pop (Optional Feature) .
#2
UNLOCK
#1
LOCK
#3
TRUNK
BUTTON 4 (Start):
• Press and Hold for two seconds to Start/Stop
Engine
BUTTON 5 (Side button)
§ Press and Release to show the previous
status.
§ Press and Hold for 5 second to switch to
vehicle #2.
#5
FLASHLIGHT
VEHICLE 2
COOLSTART
#4
REMOTE
START
Replacement Battery
GP23A (12volt)
The transmitter supplied with the CoolStart system contains four buttons, flashlight, and vehicle 2 switch. The
button configuration of the CoolStart system is Factory-set and unchangeable. See Page 16 for additional
information on how to use your remote to operate a second vehicle equipped with a CoolStart system.
NOTE: BUTTON #4 and #3 RemoteStart/Trunk
There is a deliberate delay or 2 presses (Optional) built into the system on button #4 and #3 to help prevent
accidental remote starting from the remote being in your pocket or purse. During normal use, if you press button
#4 or #3 too quickly, the system may not start the engine or open trunk.
6
USING THE 1-WAY REMOTE RS-1905FM
OPERATION:
BUTTON 1 (Lock Symbol):
• Press and release to Lock doors.
• Press and Hold for more than 3 seconds to activate
“Panic” feature.
BUTTON 2 (Unlock Symbol):
• Press and release to Unlock doors.
• Press 2 times for Driver Door Priority Unlock.
BUTTON 3 (Trunk Symbol):
• Press and Hold for ½ second or press twice to
activate trunk pop.
BUTTON 4 (Start):
• Press and Battery
Hold for ½ second or press twice to
Replacement
Start/Stop
Engine.
GP23A
(12volt)
BUTTON 5 (Vehicle #2/ AUX#2/AUX#3/AUX#4)
§ AUX #2: Press button 5 then press button 1.
§ AUX #3: Press button 5 then press button 2.
§ AUX #4: Press button 5 then press button 3.
§ vehicle #2.
§ Press and Hold for 2 sec. for vehicle #2.
#3
TRUNK
(AUX#4)
#1
UNLOCK
(AUX#2)
#2
LOCK
(AUX#3)
START
#4
REMOTE
STARTER
COOL START
#5
2ND VEHICLE
The transmitter supplied with the RS-1804FM/1905FM system has five buttons. The button configuration of the
RS-1804FM/1905FM is Factory-set and unchangeable. See Page 16 for additional information on how to use your
remote to operate a second vehicle equipped with a CoolStart system.
NOTE: BUTTON #4 and #3 Remote Start/Trunk
There is a deliberate delay or 2 presses (Optional) built into the system on button #4 and #3 to help prevent
accidental remote starting from the remote being in your pocket or purse. During normal use, if you press button
#4 or #3 too quickly, the system may not start the engine or open trunk.
7
REMOTE ENGINE STARTING
REMOTEENGINESTARTING - SUCCESSFUL START:
1) Press the remote start button for at least 1/2 second (Default) or twice if set for double press.
2) Parking lights flash once; return solid, and the Ignition/Acc circuits turn on.
3) After a few seconds the Starter Motor engages, Parking lights and Acc circuits will turn off while cranking.
4) Engine Starts and Runs. Parking Lights and Acc turn back on, Doors Lock.
5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can be
turned off with remote transmitter by pressing and releasing or double press the Start button.
SOLID
FLASH 1X
AFTER
IGN
4
SEC.
THEN
SOLID
STARTER
THE REMOTE STARTER BUTTON IS PROGRAMMABLE FOR 1 OR 2 PRESSES
REMOTEENGINESTARTING - UNSUCCESSFUL START
In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, and then
attempts to restart the engine a 2 nd and 3 rd time. For hard starting engines, the unit will allow a starter crank time of
up to 10 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 13
seconds to help prevent damage to the starter from over cranking.
1) If engine starts on 2 nd or 3 rd attempt, see steps 4 & 5 above of "Successful Start".
2) If Third attempt fails to start engine, the system will turn off and doors will remain locked.
NO FURTHER ATTEMPTS WILL BE MADE AUTOMATICALLY
TURNING OFF A REMOTE STARTED ENGINE:
1) Engine is running in Remote Start (Parking lights ON).
2) Press and release the remote start button.
3) Engine & parking lights OFF, Doors re-lock/re-arm.
8
REMOTE ENGINE STARTING Cont.
ENTERING YOUR REMOTE STARTED VEHICLE:
1) With engine running, Remote Unlock system (If equipped) or open door with key.
2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset).
3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.
4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key is
now controlling your vehicle.
REMOTESTART RUN TIME RESET:
You can now reset the engine-run timer to allow for more running time after remote start has already occurred
using the remote control. After a successful remote start, press both the Lock & Unlock buttons together for at
least 2 seconds. The parking lights will flash 3 times and internal engine timer will reset back to zero minutes.
IDLE DOWN MODE:
This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you
exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the
programmed run time or until you come back.
Examples:
• You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you exit the vehicle,
(with keys in hand) remote lock doors or arm alarm. When you return, unlock, turn ignition ON and drive away.
9
REMOTE ENGINE STARTING
IDLE DOWN MODE - EXITING THE VEHICLE:
1) With vehicle engine running with key, **press the Remote Start button for at least a 1/2 second or twice if set for
double press.
2) Parking Lights will turn ON.
3) Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released.
4) Turn OFF Ignition and remove key. Engine should remain running.
5) Exit vehicle, then remote lock doors if desired.
6) Engine will remain running for programmed run time or until you return (whichever comes first).
SOLID
IGN
OFF
UNLOCK
ENTERING A VEHICLE DURING “IDLE-DOWN” or “INFINITY RUN” MODES:
1. With engine running in "IDLE DOWN" (parking lights ON), unlock door via remote or key.
2. Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)
3. Turn Ignition to ON/RUN position, then depress brake p edal to reset the Remote Starter. Parking lights will
turn off indicating the Remote Start is OFF and Vehicle is running by the Key. Drive away as normal
INFINITY RUN MODE
This mode can only be activated when "Idle Down" procedure. The Infinity Run mode allows the vehicle engine to
remain running INDEFINITELYaftertheprogrammedruntimeelapses. This mode will allow the vehicle to be left
running and unattended without the ignition key in the switch preventing the vehicle from being stolen. This mode
can be beneficial to law enforcement or commercial trucks that need to remain running unattended for long periods
of time. See next page for Infinity mode steps.
**Programmable for ½ second press or double press. This option is selectable by your installer.
10
REMOTE ENGINE STARTING
INFINITY RUN MODE – EXITING THE VEHICLE:
1) With vehicle engine running with the key, **press the Remote Start button for at least 1/2 second, pause a few
seconds, then press and release the remote start button a second time.
2) Parking Lights will start flashing, and doors will unlock.
3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.
4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36, or 48 minutes and then
switch to solid while motor runs indefinitely or until fuel supply runs out.
SELECTABLEHOURLYCOLD-START MODE (1- 4 HOURS)
This mode allows the vehicle to be programmed to self-start every 1, 2, 3 or 4 hours and run for the programmed
run time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. THE
VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA! Once this mode is set, the unit will start at
the programmed hourly interval and run for the programmed run time. To reset this mode, start the vehicle with the
key or the remote control.
SELECTABLEHOURLYCOLD-START MODE – EXITING THE VEHICLE:
1) Engine should be running with the Key. ** Press the Remote Start button for at least 1 second. Lights will turn
on signaling the remote start has turned on and doors will unlock.
2) Within 10 seconds press and release the valet/program button once for each hourly increment (1 time = 1hour,
2X = 2 hours, 3X = every 3 hours, 4X = every 4 hours).
3) Parking Lights will turn once the button is pressed and flash for each consecutive button press.
4) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.
5) Once outside the vehicle, press and release the remote start button to turn off engine. The parking lights will
flash the number of times indicating the hourly increment for confirmation.
6) The vehicle will start by itself at the selected hourly increment until driven with key or started via the remote
control.
**Programmable for ½ second press or double press. This option is selectable
by your installer.
11
TURBO TIMER MODE (OPTIONAL)
The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1
to 5 minutes [selectively] after you remove the key, exit t he vehicle, and lock the doors remotely. This is handy for
turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a
momentary switch/button that is not included with the kit. Check with your installer about adding this feature.
NOTE: The turbo timer button will also trigger a remote start if it is inadvertently pressed when the vehicle is not
running. Please note this when installing the button and choose a location out of harm’s way.
1)
2)
3)
4)
Engine should be running with the key.
Press and hold down the brake pedal.
Press your “Turbo Timer” button 1 to 5 times for each minute of run time you desire. (1 press = 1 min.)
As you release the brake pedal and your system will confirm by flashing the lights the same number of times the
button was pressed.
5) Turn Ignition switch OFF, remove key and exit the vehicle. Remote lock your doors for safety. The engine
should remain running for the selected number of minutes.
RUNNING
LIGHTS
FLASH 1-5X
PRESS TURBO
TIMER BUTTON
1-5 TIMES
PRESS
AND HOLD
BRAKE
RELEASE
BRAKE
REMOVE KEY
EXIT VEH.
12
REMAIN
RUNNING
1-5 MIN.
CONVENIENCE AND SAFETY FEATURES
KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional)
This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety
and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as
you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the remote
start system, the lights will flash, but return back to solid.
AUTOLOCK/UNLOCK(Improved)
The Auto Lock feature controls whether the doors will automatically lock/unlock on your vehicle when driving or with turning
the Ignition ON/OFF. If the Auto Lock feature is turned on, and your system is in “Tach” mode, then the doors should
automatically lock as the engine RPM increase (driving). If the Auto Lock feature is turned on, and your system is in “Smart
Tachless” mode, then the doors will lock a few seconds after the Ignition is turned on. When the Auto Lock feature is turned
on, the system will always unlock the doors when the Ignition is turned off. With this feature turned OFF, the system will not
automatically lock or unlock the vehicle. See your installer for programming information on this feature.
DOORLOCKNOTE: If your system has been setup with an optional starter kill relay, but you do not have power door locks, note
the following: The lock and unlock buttons on the remote control must still be utilized to operate the Starter disable.
REMOTE PANIC (Used only with Optional HORN HONK feature installation)
For personal safety this unit now includes a panic feature. To sound the vehicle car horn, press the Lock Button on the
remote for more than 2 seconds. The vehicle horn will honk along with flashing parking lamps for 1 minute. Reset Remote
Panic by pressing either the lock or unlock button. See next section for Horn Honk information.
HORN CHIRP/HONK OUTPUT (Optional: with Horn connection & programming)
This feature, if installed, will provide audible confirmation chirps from the factory horn for lock and unlock. When using this
feature, pressing the Lock or Unlock button a 2nd time within 3-7 seconds will provide a horn chirp for audible confirmation.
The system can also be programmed to provide 3 chirps when a remote start is requested using the remote. Note: Horn
honk/chirp feature may require extra labor and/or parts to install.
REMOTE TRUNK RELEASE OR DOMELIGHT ILLUMINATION (Optional)
This CoolStart system includes an output that can be programmed to remotely release a factory electronic trunk or
illuminate the interior light when you unlock your vehicle for lighted entry at night. If you have the optional trunk pop
installed, simply press and release the Trunk Button #3 on the transmitter or if option # 6 is turned on you must press Button
# 3 twice within 3 seconds, to remotely open trunk. If your system is programmed for Dome Light illumination, then it will
work automatically lighting the dome light for 30 seconds when you unlock your vehicle via the remote. The dome light will
turn off after 30 seconds, or turning the key on (whichever comes first). The trunk Pop or Dome Light Illumination may
require extra labor and/or parts to install.
13
CONVENIENCE AND SAFETY FEATURES
VALET MODE / STARTER DISABLE OVERRIDE
Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode.
The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON
position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid and the system is now in
valet. Perform this procedure again to exit of Valet mode. The keyless entry will still function normally while in
valet mode. In the event of a lost or broken transmitter, perform this step to override the Starter Disable (if
installed).
ANTI-GRIND / STARTER DISABLE (Optional, relay not included)
This Optional feature prevents the user from accidentally grinding the starter if the Ignition key is turned too far to the start position
while engine is already running from the remote starter. The Anti-Grind/Starter Disable requires the use of an external relay. This
system must be programmed to allow the relay to work as a starter disable.
PASSIVE STARTER DISABLE (Optional)
This COOLSTART system includes a programmable feature to allow the Optional Starter Disable to activate
automatically 1 minute after the ignition is turned off. This programmable feature may provide insurance discounts
for “Passive Security” functions, or meet an insurance requirement in your province (CAN).
HOOD OPEN SAFETY (Requires grounding hood pin installation)
Prevents the engine from being Remote Started when hood is open and will shut OFF the engine if opened d uring
while remote started. Eliminates risk of injury to someone working under the hood of the vehicle with a properly
working hood pin installed. If Remote Start button is pressed with the hood open, the lights will flash once and the
unit will not attempt a start.
BRAKE PEDAL RESET
Prevents starting or shuts off a remote started vehicle when this circuit is active or activated. Prevents unauthorized tampering. This
circuit shuts the system down immediately when brake pedal is pressed if the key is not in ignition and turned to the ON position.
OEM ALARM INTERFACE
This feature is designed to Disarm and Re-arm Factory equipped security systems in conjunction with remote start and keyless entry
(if needed for your vehicle). This feature will maintain the original integrity and security of your vehicle’s factory equipped systems
before, during, or after remote start.
NOTE:
When changing, charging, or jumpstarting the vehicle’s battery we recommend removing the main power fuses
located on the heavy gauge RED wires near the remote start module.
14
TRANSMITTER PROGRAMMING
Note: All transmitter codes must be learned at time of programming!! The unitwill learns up to 4 different
transmitter codes.
1.
2.
3.
4.
Open Hood (If no hood pin installed with your system, then you must ground the Gray Hood pin wire).
Turn key to the ON position.
Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times.
Press button #1 & #2 together of the transmitter to be coded. You should get 2 light flashes indicating the unit is
waiting for a 2 nd code, then press button #1 & #2 of a second transmitter, the unit will flash 3 times indicating its
waiting for the 3 rd code and so on. If all 4 codes are learned, the unit will automatically exit code learning mode,
otherwise turn key off and close hood. See diagram below.
IGN
OFF
WAIT FOR
4 FLASHES
(GRAY WIRE GROUNDED)
PRESS4X's
1-WAY
IGN
OFF
START
COOLSTART
FLASH 2, 3, or 4 X's
PRESSTOGETHER
15
2-VEHICLE OPERATION
A single remote can control two different vehicles CoolStart
systems installed. However, both systems must be the same
type. RS-1604TW1/1704TW2 is not compatible with RS1804FM/ 1905FM.
Programming:
1 WAY SIDEKICK REMOTE
VEHICLE #2
Press side button
You must first Programming your remote for
2nd vehicle operation:
(2nd Vehicle Programming and Operation instruction):
1 Way sidekick remote
In step #4 of transmitter programming (see page 15) press side
button first, then you have 3 seconds to press lock and unlock
at the same time, parking light will flash indicating the remote is
programming.
Operation:
Press the vehicle #2 side button on your remote first and within
3 seconds press any of the 4 function buttons on your remote.
You can keep pressing function buttons to control car #2 as long
as it is within the 3-second window. After 3 seconds have
elapsed, the remote will revert back to Car #1 operation.
1 Way 5 button sidekick remote
In step #4 of transmitter programming (see page 15) press and
hold middle button #5 for 2 sec., then press lock and unlock at
the same time, parking light will flash indicating the remote is
programming.
Operation:
Press vehicle #2 button (middle button) for 2 sec. and within 3
seconds press any of the 4 function buttons on your remote.
You can keep pressing function buttons to control car #2 as long
as it is within the 3-second window. After 3 seconds have
elapsed, the remote will revert back to Car #1 operation.
16
first, then you have
3 seconds to
COOLSTART
control vehicle #2.
VEHICLE 2
Press Middle
Button first,
START
Then you have
COOL START
3 seconds to
Control vehicle #2
2-VEHICLE OPERATION Cont.
L.E.D Two-way Remote
In step #4 of transmitter programming (see Page 15), press and hold the side button on the LED remote for 5 seconds. The
unit will beep 2 times and a yellow LED will flash (now you are in 2nd vehicle operation mode). Press the lock and unlock
button at the same time on the LED remote, your vehicle should be programmed for the 2nd vehicle.
Operation:
Press the car vehicle #2 side button on your remote for 5 seconds to enter 2nd vehicle mode, press any of the 4 function
buttons on your remote. You can keep pressing function buttons to control car #2 as long as it is within the 18-second
window. After 18 seconds have elapsed, the remote will revert back to Car #1 operation.
LCD Two-way Remot e
In step #4 of transmitter programming (see Page 15), press and hold the side button on the LCD remote for 2 seconds. The
unit will beep 1 time and a 2 will display on the screen (now you are in 2nd vehicle operation mode). Press the lock and
unlock button at the same time on the LCD remote, your vehicle should be programmed for the 2nd vehicle.
Operation:
Press the car vehicle #2 side button on your remote for 2 seconds to enter 2nd vehicle mode, a 2 will display on the screen.
You are now in 2nd vehicle mode. To return to vehicle 1, repeat previous steps and a 1 will display indicating you are in
vehicle 1 mode.
TROUBLESHOOTING: “BEFORE YOU CALL” SECTION
UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY STILL FUNCTIONS NORMALLY):
The unit is in Valet mode. Turn Ignition ON, press and hold valet/programming button for 6 seconds then turn key
off. Unit is now out of valet mode and should perform a remote start. If optional LED indicator is installed, then it
will be on solid when in Valet and OFF when out of Valet.
UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START:
The unit senses a fault at the Brake (Purple wire is active) or the Hood is OPEN (Gray wire grounded). This is a
safety feature of the unit. Check installation for faults and make sure hood is closed and latched and brake wire is
not active. Make sure hood is in good condition and is depressed when hood is closed.
17
TROUBLESHOOTING cont.
NO RESPONSE FROM REMOTE TRANSMITTERS: (4 Parts)
1. Check for proper power/ground wiring connections at module.
2. Check Antenna Module connection. The antenna module included with this system must be plugged in.
3. Transmitters may need to be programmed to the unit. See transmitter programming steps on Page 1 5.
4. Check transmitter Batteries and replace if necessary.
UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: (2 parts)
1. In extreme cold or severe weather conditions, the unit may take more than the first attempt to start the vehicle.
The remote start unit will make up to 3 attempts to start the engine.
2. In some v ehicles, there may be a Factory anti-theft system that will not allow the engine to run without the key in
the ignition. These systems may include Factory Security Modules, GM Passkey®/Passlock®, and RF
Transponder systems (Ford P.A.T.S. ®). Many late 1990’s through 2005 vehicles include some type of AntiTheft system which may require a bypass module. Check with your installer to make sure that the bypass
device (if equipped) is functioning properly.
SYSTEM IS UNSUCCESSFUL AT REMOTE START DURING EXTREME COLD CONDITIONS:
Please be aware that during sub-freezing conditions your remote starter may take more that one attempt to start or
it may not successfully start the vehicle after 3 attempts. During these conditions the vehicle may not properly start
even using the key; therefore trying to start by the remote would also be unsuccessful.
VEHICLE STARTS BUT “CHECK ENGINE” LIGHT COMES ON OR ENGINE RUNS BADLY: (2 parts)
1. Many 1995-UP General Motors cars/trucks require a secondary ignition circuit for the Transmissioncomputer
and other on board systems. If the vehicle is started without this wire energized, there may be a “Check Engine”
or “Service Engine Soon” light on the dash. This may cause damage if the vehicle is driven in this condition.
Check with installer to see if this circuit is present and has been properly connected to the system.
2. In some cases [commonly Nissan vehicles], an additional “Start” (Cranking) circuit is required for the vehicle to
run properly. The CoolStartsystem includes a wire that can be used for this Starter #2 circuit. Check with your
installer for details.
18
LOW BATTERY WARNING - LCD REMOTE (RS-1604TW1/RS-1704TW2)
RS-1604TW1 (LED system): When the battery is low the orange and green LED flash 6
times with any button pressed.
RS-1704TW2/RS-1804FM/1905FM (LCD SYSTEM): When the battery is low, a low battery
icon turns on. We recommend replacing the battery for proper operation.
REPLACING THE BATTERY
LOW BATTERY
WARNING
REPLACINGTHEBATTERY
To replace the battery simply unlock and slide to open the battery door on the back of LCD remote. Carefully
remove the low battery. Then insert a new battery (AAA) using the outline on the bottom of the battery
compartment as a guide.
RS-1604TW1
Pager will beep 3 times when new battery is inserted correctly.
RS-1704TW2
Pager will beep 3 times, vibrate and light up screen when new battery is inserted correctly.
RS-1804FM/1905FM: Pager will light up screen then beep once. When a new battery is inserted correctly.
Note: If the remote doe not beep or respond you must reinsert battery again.
19
SETTING THE CLOCK (2-WAY- LCD REMOTE)
RS-1704 TW1
1.
2.
3.
4.
5.
6.
7.
Press the Recall button #5 on the side of the remote control 5 times.
The remote will beep and the AM or PM display will begin flashing.
Press the Lock button #1 to increase time.
Press the Unlock button #2 to decrease time.
Press the Trunk button #3 to go to the next item – AM - PM - Hour - Minutes.
Press the Start button #4 to Disable or Enable Beep.
Press the Recall button #5 to Exit Setup or wait 7 seconds, the LCD light will turn off.
RS-1804FM/1905FM
1. Press and hold all 4 buttons of remote control for approximately 3 seconds until remote beeps.
2. The minute display will begin flashing. Use the lock and unlock button to change the minute up or down to the correct time
and then press button #3 (Trunk) to set the minute value.
3. The hour display should begin flashing. Use the lock and unlock button to change the hour up or down to the correct AM or
PM hour.
4. Once the correct time is displayed, wait 6 seconds, the remote will beep twice and the time of day is set.
www.crimestopper.com
email@crimestopper.com
© 2005 Crimestopper Security Products
ONLINE TECHNICAL SUPPORT
http://www.crimestopper.com
Download PDF