Gold Medal 1888 Snow Cone Machine Instruction Manual

WWW.CONCESSIONSTANDS.COM
WARNING!!
co
n
ce
ss
i
on
st
an
ds
.c
om
The attached Gold Medal Manual is for
reference only and is not intended for any
other purpose. The information contained in
these on line manuals is subject to change
at any time. Improvements are always
being made to Gold Medal equipment and
this information may not be the latest
available for your purposes. It is critical that
you call Gold Medal Products technical
service department at 1-800-543-0862 for
any questions about machine operations,
replacement parts, or any service questions.
Neither Gold Medal nor Jarco Industries
represent that these on line manuals
contain the most current information
available for the product represented.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
WWW.CONCESSIONSTANDS.COM
Part No. 12666
Revised JAN 2003
Sno-King
Instruction Manual
ss
i
on
st
an
ds
.c
om
Model #1888
co
n
ce
Model #1888
Cincinnati, OH 445241-4807 USA
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
WWW.CONCESSIONSTANDS.COM
Sno-King
co
n
ce
ss
i
on
st
an
ds
.c
om
Safety Precautions
2
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
INSTALLATION
MACHINE DESCRIPTION
.c
om
The Sno-King is an automatic shaver with a tremendous capacity. You will find that it keeps up with any
demand. The Sno-King consists of the hopper, which houses the cutter head, the pusher handle, the motor,
and the display case.
ELECTRICAL REQUIREMENTS
The Sno-King operates on 120 Volt, 15 Amp, single phase, 60 cycle AC current. Be sure that your electrical
supply meets this requirement.
ds
ICE REQUIREMENTS
an
The Sno-King can take ice cubes or block ice, if you break the block into pieces approximately 3 to 4 inches
in size.
st
NOTE: The ice will not enter the shaving chute if the pieces are too large.
on
MACHINE OPERATION
ss
i
Plug the power cord into the appropriate electrical outlet.
TO OPERATE THE SNO-KING
co
n
ce
1. Fill the hopper to within an inch of the top with ice cubes or block ice (no larger than 3" to 4"). The larger
the pieces, the better the snow.
2. Toggle the POWER switch to the ON position.
3. While pushing the MOTOR switch, apply downward pressure to the pusher handle. Apply firm and even
pressure to make the best snow. Practice will allow you to gauge when to stop pressing. This allows the
ice to resettle against the shaver head. Too much pressure will result in snow that is coarse; too little
pressure will make the snow mushy.
NOTE: Never allow any foreign or metallic objects around the shaver area of the Sno-King. Ice picks,
scoops, and debris that may be in the ice often damage blades.
3
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
co
n
ce
ss
i
on
st
an
ds
.c
om
MAINTENANCE INSTRUCTIONS
4
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
ORDERING SPARE PARTS
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
co
n
ce
ss
i
on
st
an
ds
(513) 769-7676
Fax: (513) 769-8500
E-mail: [email protected]
.c
om
1. Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity desired.
3. Please include your model name and machine serial number (located on the machine nameplate) with
your order.
4. Address all parts orders to:
5
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
INSTALLING NEW SHAVER BLADES
Inspect your equipment before replacing the blades. With the POWER switch OFF, use a flashlight to
examine the blades in the shaver body. If the blades appear to be nicked or bent, then the blades should be
replaced.
on
st
an
ds
.c
om
Follow this procedure:
1. Unplug the main power supply cord from the electrical outlet.
2. Remove the shaver head from the motor shaft by loosening the Allen head set screws between the
motor and the hopper.
3. Remove the shaver head. Pull the shaver head off of the motor shaft and through the hopper. If the
shaver head is frozen onto the shaft, remove the hold down bolts on the motor. Pull the motor back,
trapping the shaver head against the inside of the hopper, until the shaver head disengages.
4. After removing the shaver head, check the motor shaft for burrs and corrosion. Use a fine tooth file to
remove the burrs and corrosion.
5. Remove the blades from the shaver head. These blades may be re-sharpened, but it is far better to
replace the old blades with a new set.
6. Position the new blades and insert screws until they are finger tight.
7. Set the blade thickness equal to a dime. (See illustration below.) Make sure that the height is even
across the shaver head.
8. Tighten the blade screws completely. Check the blades again with a dime to ensure the blades did not
move while tightening the screws.
9. Replace the motor and shaver head. Mount the motor using the hold down bolts. Insert the shaver head
through the hopper and onto the motor shaft. Press the shaver head onto the motor shaft with the
pusher handle, then move the shaver head in another 1/8". Check that the shaver head is not rubbing
against the back of the hopper and the blades are not touching the pusher handle.
10. Replace the set screws between the hopper and the motor.
ce
ss
i
NOTE: Replace any shims that were between the motor base and the mounting surface.
HEIGHT GAGE
(USE A DIME)
co
n
SET TOP OF BLADE
FLUSH WITH HEIGHT
GAGE, AS SHOWN
SHAVER BLADE
BLADE MOUNTING SCREW
SHAVER HEAD
6
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
#1888 ASSEMBLY
25
8
7
3
12
2
.c
om
9
10
an
ds
11
5
on
st
16
4
14
co
n
15
13
.
ce
ss
i
1
6
7
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
#1888 ASSEMBLY
18
19
co
n
ce
ss
i
on
st
an
ds
.c
om
17
8
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
SHAVER HEAD
20
22
co
n
ce
ss
i
on
st
an
ds
.c
om
21
24
23
9
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
ds
ss
i
on
st
an
Description
Shaver Body
Plunger
Pusher Cap
Neck Bracket
Side Panel
Front Panel
Motor Cover
Motor - Drive
Name/Switch Plate
Momentary Switch
Switch, Lighted Rocker
Pivot Rod
Drain Fitting
Glide
Crutch Tip
Lead-in Cord 15 Amp Plug
3 inch Fan Grate
Plate, Power Cord
Strain Relief
Set Screw 1/4-20 x 3/8
Shaver Head
2 Hole Blade
Blade Mtg Screw Brass
#8 Brass Washer
Wire Enclosure
co
n
ce
Model #
1888
Item No. Part No.
1
12660
2
12662
3
12671
4
12667
5
12663
6
12664
7
12661
8
12456
9
12665
10
38971
11
42798
12
12670
13
12668
14
49656
15
49123
16
22038
17
74746
18
12673
19
44073
20
74125
21
22015NM
22
22018
23
12018
24
12073
25
12672
26
27
28
29
30
31
32
33
34
35
.c
om
PARTS LIST
** The replacement kit includes two blades, the screws and washers, and the warning label.
10
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888
WWW.CONCESSIONSTANDS.COM
Sno-King
co
n
ce
ss
i
on
st
an
ds
.c
om
ELECTRICAL SCHEMATIC
MODEL #1888
11
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
All Models #1888