Eizo | EIZO FlexScan L 788 L788 L788 | User`s manual | Eizo EIZO FlexScan L 788 L788 L788 User`s manual

For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan L788
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
User’s Manual
Color LCD Monitor
English
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read
them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury
and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury
and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2006-2007 EIZO NANAO CORPORATION All rights reserved. No part of this
manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, or otherwise, without the prior written permission of EIZO
NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to EIZO NANAO
CORPORATION's receipt of said information. Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor
specifications are subject to change without notice.
ENERGY STAR is a U.S. registered mark.
Apple, Macintosh and Power Macintosh are registered trademarks of Apple Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards
Association.
Windows is a registered trademark of Microsoft Corporation.
PowerManager is a trademark of EIZO NANAO CORPORATION.
i·Sound L3, ScreenManager, FlexScan and EIZO are registered trademarks of EIZO NANAO
CORPORATION in Japan and other countries.
As an ENERGY STAR® Partner, EIZO NANAO CORPORATION has determined that
this product meets the ENERGY STAR guidelines for energy efficiency.
Product specifications may vary depending on the region. Confirm the specifications in
the manual written in the language of the region of purchase.
2
English
TABLE OF CONTENTS
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1-1. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1-2. Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1-3. Controls & Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.
CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2-1. Before Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2-2. Connecting the Signal Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2-3. Connecting Two PCs to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.
ScreenManager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3-1. How to use the ScreenManager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3-2. ScreenManager Adjustments and Settings. . . . . . . . . . . . . . . . . . . . . . . 19
3-3. Useful Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4-1. Screen Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4-2. Displaying Low Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4-3. Color Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4-4. Power-save Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.
MAKING USE OF USB (Universal Serial Bus) . . . . . . . . . . . . . . . . . . . . . . . 33
6.
ATTACHING AN ARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9.
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10. GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
APPENDIX/ANHANG/ANNEXE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Table of contents
3
English
PRECAUTIONS
IMPORTANT!
z This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally
shipped, the product may not perform as stated in the specifications.
z To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).
[Location of the Caution Statements]
WARNING
If the unit begins to emit smoke, smells like something is
burning, or makes strange noises, disconnect all power
connections immediately and contact your dealer for advice.
Attempting to use a malfunctioning unit may result in fire, electric
shock, or equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire,
electric shock, or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or
removing covers may result in fire, electric shock, or equipment
damage.
4
PRECAUTIONS
English
WARNING
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into
the cabinet or spillage into the cabinet may result in fire, electric
shock, or equipment damage. If an object or liquid falls/spills into
the cabinet, unplug the unit immediately. Have the unit checked by
a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in
injury or equipment damage.If the unit falls, disconnect the power
immediately and ask your dealer for advice. Do not continue using
a damaged unit. Using a damaged unit may result in fire or
electric shock.
OK
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
z Do not place outdoors.
z Do not place in the transportation system (ship, aircraft, trains,
automobiles, etc.)
z Do not place in a dusty or humid environment.
z Do not place in a location where the steam comes directly on
the screen.
z Do not place near heat generating devices or a humidifier.
To avoid danger of suffocation, keep the plastic packing
bags away from babies and children.
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
Power supply: 100-120/200-240 VAC±10 %, 50/60 Hz
To disconnect the power cord, grasp the plug firmly and pull.
OK
Tugging on the cord may damage and result in fire or electric shock.
PRECAUTIONS
5
English
WARNING
The equipment must be connected to a grounded main outlet.
Not doing so may cause in fire or electric shock.
Use the correct voltage.
z The unit is designed for use with a specific voltage only.
Connection to another voltage than specified in this User’s
Manual may cause fire, electric shock, or equipment damage.
Power supply: 100-120/200-240 VAC±10 %, 50/60 Hz
z Do not overload your power circuit, as this may result in fire or
electric shock.
Handle the power cord with care.
z Do not place the cord underneath the unit or other heavy objects.
z Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a
damaged cord may result in fire or electric shock.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s
manual of the arm stand and install the unit securely.
Not doing so may cause the unit to come unattached, which may
result in injury or equipment damage. When the unit is dropped,
please ask your dealer for advice. Do not continue using a
damaged unit. Using a damaged unit may result in fire or electric
shock. When reattaching the tilt stand, please use the same screws
and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal which leaks from the panel is poisonous if it
enters the eyes or mouth. If any part of the skin or body comes in
direct contact with the panel, please wash thoroughly. If some
physical symptoms result, please consult your doctor.
Follow local regulation or laws for safe disposal.
The backlight of the LCD panel contains mercury.
6
PRECAUTIONS
English
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit.
Moving the unit with the cord attached is dangerous. It may
result in injury.
When handling the unit, grip the bottom of the unit firmly
with both hands ensuring the panel faces outward before
lifting.
OK
Dropping the unit may result in injury or equipment damage.
Do not block the ventilation slots on the cabinet.
z Do not place any objects on the ventilation slots.
z Do not install the unit in a closed space.
z Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may
result in fire, electric shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case
of a problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result
in electric shock.
If you plan to leave the unit unused for an extended period,
disconnect the power cord from the wall socket after turning
off the power switch for the safety and the power
conservation.
PRECAUTIONS
7
English
LCD Panel
When the monitor is cold and brought into a room or the room temperature goes up
quickly, dew condensation may occur inside and outside the monitor. In that case, do
not turn the monitor on and wait until dew condensation disappears, otherwise it
may cause some damages to it.
In order to suppress the luminosity change by long-term use and to maintain the
stable luminosity, use of a monitor in lower brightness is recommended.
The LCD panel is manufactured using high-precision technology. However, note that
the appearance of any missing pixels or lit pixels does not indicate damage to the
LCD monitor. Percentage of effective pixels: 99.9994% or higher.
The backlight of the LCD panel has a fixed life span. When the screen becomes dark
or begins to flicker, please contact your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in damage
to the screen. There will be prints left on the screen if the pressed image is dark or
black. If pressure is repeatedly applied to the screen, it may deteriorate or damage
your LCD panel. Leave the screen white to decrease the prints.
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as
this may result in damage to the panel. Do not attempt to brush with tissues as this
may scratch the LCD panel.
When the screen image is changed after displaying the same image for extended
periods of time, an afterimage may appear. Use the screen saver or timer to avoid
displaying the same image for extended periods of time.
8
PRECAUTIONS
English
1.
INTRODUCTION
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
z Dual inputs compliant (DVI-I x 2 connecters)
z DVI (p. 43) Digital input (TMDS (p. 44)) compliant
z [Horizontal scanning frequency] Analog: 30 - 82 kHz
Digital: 30 - 65 kHz
[Vertical scanning frequency]
Analog: 49 - 86 Hz (1280 × 1024: 49 - 76 Hz)
Digital: 59 - 61 Hz (VGA text: 69 - 71 Hz)
[Resolution]
1280 dots × 1024 lines
z Supports to sRGB (p. 44) standard
z Smoothing function incorporated for the adjustment of an enlarged image. (p. 27)
z The height adjustable stand incorporated
z Ultra slim bezel incorporated
z The Portrait/Landscape display capability
z Optional speaker “i·Sound L3” is available
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
z LCD Monitor
z EIZO LCD Utility Disk
z Power Cord
z User’s Manual
z Signal Cable (FD-C39)
z ScreenManager Quick Reference
z Signal Cable (FD-C16)
z LIMITED WARRANTY
z EIZO USB Cable (MD-C93)
z Mounting Screws: M4 × 12 (mm) × 4 pcs
(for another manufacturer's arm or stand)
NOTE
z Please retain the packing materials for future transference.
1. Introduction
9
English
1-3. Controls & Connectors
Front
(1)
Control Panel
(2) (3) (4) (5)
(1)
ScreenManager®
(2)
Input Signal Selection Button
(3)
Mode Button*1
(6)
(7) (8)
(4)
Auto Adjustment Button
(5)
Enter Button
(6)
Control Buttons*2 (Left, Down, Up, Right) *3
(7)
Power Button
(8)
Power Indicator*4
Blue
The screen is displayed
Yellow
Power saving
Flashing yellow (2 times for each)
Power save mode Digital only
Off
Power off
*1 Directly pressing the mode button allows you to switch a color mode between “Custom”
and “sRGB”. For details about color mode, see page 29.
*2 Directly pressing the control button allows you to adjust screen brightness. If you choosing
the “custom” color mode, you also may adjust screen contrast.
*3 These buttons are changed to Up, Left, Right, Down in case of selecting “Portrait” for <Orientation> of ScreenManager <Others> (p. 20).
*4 Blue lighting, when the screen is displayed (Operation mode), is made to non-light, see
page 22. Regarding the power indicator for the “Off Timer”, see page 21.
10
1. Introduction
English
Rear
Bottom
(9)
Security Lock Slot*5
(10) Height Adjustable Stand (Detachable)*6
(11) Power Connector
(12) DVI-I Input Connector (SIGNAL 1)
(13) DVI-I Input Connector (SIGNAL 2)
(14) USB Port (1 Upstream)
(15) USB Port (2 Downstream)
(16) Slots for i·Sound L3 (Optional speaker)
*5 Allows for connection of a security cable. This lock supports Kensington’s MicroSaver security system. For further information, please consult’
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403 USA
Tel.: 800-650-4242, x3348, Intl: 650-572-2700, x3348
Fax: 650-572-9675
http://www.kensington.com
*6 The LCD monitor has the capability of the Portrait/Landscape display (The panel pivots in
the clockwise direction 90°.). For the Portrait display, use the software for the portrait.
The LCD monitor can be used with an optional arm stand by removing the stand (see
page 35).
1. Introduction
11
English
2.
CABLE CONNECTION
2-1. Before Connecting
Before connecting your monitor to the PC, change the display screen settings
(resolution (p. 44) and frequency) in accordance with the charts below.
NOTE
z When your computer and display support VESA DDC, the suitable resolution and
the refresh rate are set by just plugging your display into the computer without
any manual settings.
Analog Input
Resolution
Frequency
Dot Clock
640
×
480
67 Hz
Apple Macintosh
640
×
480
~ 85 Hz
VGA, VESA
720
×
400
70 Hz
VGA TEXT
800
×
600
~ 85 Hz
VESA
832
×
624
75 Hz
Apple Macintosh
1024
×
768
~ 85 Hz
1152
×
864
75 Hz
1152
×
870
75 Hz
Apple Macintosh
1152
×
900
~ 76 Hz
SUN WS
1280
×
960
75 Hz
Apple Macintosh
1280
×
960
60 Hz
VESA
1280
×
1024
~ 75 Hz
VESA
135 MHz (Max.)
Remarks
VESA
VESA
Digital Input
Only the following resolutions with frequency can be displayed on this model.
12
Resolution
Frequency
640
×
480
60Hz
VGA
720
×
400
70Hz
VGA TEXT
800
×
600
60Hz
1024
×
768
60Hz
VESA
1280
×
1024
60Hz
VESA
2. CABLE CONNECTION
Dot Clock
108 MHz (Max.)
Remarks
VESA
English
2-2. Connecting the Signal Cable
NOTE
z Be sure that the power switches of both the PC and the monitor are OFF.
1.
Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Power Cord
Analog Input
Signal Cable
Signal Cable
(FD-C16 enclosed)
Connector
PC
Video Output Connector /
D-Sub mini 15 pin
z
Standard graphics card
z
Power Macintosh G3
(Blue & White) / Power
Mac G4 (VGA)
Input Connector (monitor) /
DVI
Digital Input
Signal Cable
Signal Cable
(FD-C39 enclosed)
Connector
PC
Video Output Connector /
DVI
z
Digital graphics board
z
Power Mac G4/G5 (DVI)
Input Connector (monitor) /
DVI
NOTE
z The monitor is not compatible with a Power Mac G4/G5 ADC (Apple Display
Connector)
2. CABLE CONNECTION
13
English
2.
Plug the power cord into the power connector on the rear of the
monitor.
3.
Lead the power cord and signal cable into the cable holder at rear
of the monitor.
NOTE
z The cables are recommended to lead with slight sag for the smooth motion
of the stand and the Portrait/Landscape display.
Cable Holder
4.
Plug the other end of the power cord into a power outlet.
WARNING
Use the enclosed power cord and connect to the
standard power outlet of your country.
Be sure to remain within the rated voltage of the power
cord.
Not doing so may result in fire or electric shock.
Power supply: 100-120/200-240 VAC±10 %, 50/60 Hz
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock.
14
2. CABLE CONNECTION
English
5.
Turn on the monitor's Power Button and then turn on the PC's
power.
The monitor's power indicator will light up (blue).
If an image does not appear, refer to the “7. TROUBLESHOOTING” (p. 36)
for advice.
Whenever finished, turn off the PC and the monitor.
NOTE
z When turning on the monitor, the kind of the input signal (Signal1 or 2/Analog or
Digital) is displayed for a few seconds on the right top corner of the screen.
z Adjust brightness of the screen depending on the brightness of your
environment.
z Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
2. CABLE CONNECTION
15
English
2-3. Connecting Two PCs to the Monitor
Two PCs can be connected to the monitor through the Signal 1 and the Signal 2 on
the back of the monitor.
Connecting Examples
DVI-I Input Connector
(SIGNAL 1)(SIGNAL 2)
PC 1
16
Ex.1
Digital
DVI
Ex.2
Analog
Ex.3
Digital
Signal Cable
(FD-C16 enclosed)
D-Sub Analog
mini
15 pin
D-Sub Signal Cable
mini
(FD-C16 enclosed)
15 pin
Signal Cable
(FD-C16 optional)
D-Sub Analog
mini
15 pin
DVI
Signal Cable
(FD-C39 optional)]
DVI
2. CABLE CONNECTION
Signal Cable
(FD-C39 enclosed)
PC 2
Signal Cable
(FD-C39 enclosed)
Digital
English
Selecting the Active Input
The Input Signal Selection Button on the control panel can be used to select either
SIGNAL 1 or SIGNAL 2 as the active input at any time. Every time the button is
pressed, the input changes. When switching the signal, the kind of the input signal
(Signal1 or 2/Analog or Digital) is displayed for a few seconds on the right top corner
of the screen.
Input Signal Selection Button
The Priority Input Signal
This function is used to select which PC will have priority to control the monitor
when utilizing two PCs. The monitor constantly checks the input signals and switches
automatically in accordance with the “Input Priority” setting (see table below). Once
a priority is set, whenever a change of signal is detected at the selected input, the
monitor will switch the input to that signal.
In the case of only one signal being present at either input, the monitor automatically
detects and displays that signal.
Priority setting
1 (SIGNAL 1)
2 (SIGNAL 2)
Manual
Performance
If signals from both inputs are present, the monitor gives preference
to Signal 1 in the following cases.
z
When the power of the monitor is turned ON.
z
When the signal input to Signal 1 is changed even if active input
was Signal 2.
If signals from both inputs are present, the monitor gives preference
to Signal 2 in the following cases.
z
When the power of the monitor is turned ON.
z
When the signal input to Signal 2 is changed even if active input
was Signal 1.
The monitor will not detect signals automatically in this mode. Select
the active input by pressing the Input Signal Selection Button on the
monitor's control panel.
NOTE
z When the “1” or “2” is selected, the power saving mode of the monitor activates
only if both PCs are in power saving mode.
2. CABLE CONNECTION
17
English
3.
SCREENMANAGER
3-1. How to use the ScreenManager
Main Menu
Control Buttons
Left, Down, Up, Right
Auto Adjustment Button Enter Button
1.
Entering the ScreenManager
Press the Enter Button once to display the main menu of the ScreenManager.
2.
3.
Making Adjustments and Settings
(1)
Select the desired sub menu icon using the Control buttons and press the
Enter Button. The sub menu appears.
(2)
Use the Control buttons to select the desired setting icon and press the
Enter Button. The setting menu appears.
(3)
Use the Control buttons to make all required adjustments and press the
Enter Button to save the settings.
Exiting the ScreenManager
(1)
To return to the main menu, select the <Return> icon or press the down
button twice, followed by the Enter Button.
(2)
To exit the ScreenManager, select the <Exit> icon or press the down
button twice, followed by the Enter Button.
NOTE
z Double clicking the Enter Button also exits the ScreenManager menu.
18
3. ScreenManager
English
3-2. ScreenManager Adjustments and Settings.
The following table shows all the ScreenManager's adjustment and setting menus.
“*” indicates adjustments of analog input only and “**” indicates digital input only.
Main menu
Screen
Sub menu
Reference
Clock
*
Phase
*
Position
*
Resolution
*
Range Adjustment
*
4-1. Screen Adjustment (p. 23)
Smoothing
Signal Filter
Color
Management
(Custom)*1
*
Color Mode
4-3. Color Adjustment (p. 29)
Brightness
Contrast
Temperature
Saturation
Hue
Gain
Reset
Power Manager DVI DMPM
**
VESA DPMS
*
EIZO MPMS
*
4-4. Power-save Setup (p. 31)
3. ScreenManager
19
English
Main menu
Others
Sub menu
Screen Size
Reference
4-2. Displaying Low Resolutions (p. 27)
Border Intensity
Input Priority
Select the priority input signal. (p. 17)
Off Timer
Set the monitor's off timer to on or off.
(p. 21)
Beep
Set the monitor's beeper to on or off.
(p. 41)
Menu
Settings
Menu Size
Change the size of the menu.
Menu Position
Adjust the menu position
Menu Off Timer
Set the menu displaying time.
Translucent
Set the transparency of the background.
Orientation
Change the orientation of the
ScreenManager for monitor's portrait
position.
Power Indicator
Make non-light for blue lighting when the
screen is displayed. (p. 22)
Reset
Return to the factory default settings.
(p. 41)
Information
Information
Review the ScreenManager's settings,
model name, serial number and usage
time.*2
Language
English, German, French,
Spanish, Italian, Swedish
and Japanese
Select the ScreenManager's language.
*1 The above table shows the sub menus when the “Custom” mode is selected (see page 29).
*2 Due to the inspection on the factory, the usage time may not be “0 hour” at shipping.
20
3. ScreenManager
English
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
Unlocked function
z
Adjustments and settings in the ScreenManager.
z
Auto Adjustment Button
z
Brightness/ Contrast adjustments through the control buttons
z
Input Signal Selection Button
[How To lock]
(1)
Switch off the monitor's power by the power button on the control panel.
(2)
Press on the Auto adjustment button while switching on the monitor's power.
[How To unlock]
(1)
Switch off the monitor's power by the power button on the control panel.
(2)
Hold down the Auto adjustment button once again and turn the power back
on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state
after a predetermined amount of time has lapsed. This function was created to reduce
afterimage characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.
[Procedure]
(1)
Select <Off Timer> in the ScreenManager <Others> menu.
(2)
Select “Enable” and press the right and left buttons to adjust the “On Period”
(1 to 23 hours).
[Off Timer System]
PC
Monitor
Power Indicator
On Period (1H - 23H)
Operation
Blue
Last 15 min. in “On period”
Advance Notice*1
Blue Flashing
“On period” expired
Power Off
Light Off
*1 Advance notice (Power Indicator flashing blue) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode,
press the Power Button during the advance notice period. The monitor will continue to operate for an additional 90 minutes.
3. ScreenManager
21
English
[Power Resumption Procedure]
Press the Power Button to return to a normal screen.
NOTE
z The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor's power is turned off.
Power Indicator Setting
Light off the power indicator. This function is available for the multiple panels
settings.
[Procedure]
(1)
Select <Power Indicator> in the ScreenManager <Others> menu.
(2)
Select “Disable”.
EIZO Logo Appearing Function
When switching on the Power Button on the control panel, the EIZO logo is
displayed for a while. If you desire to display or undisplay this logo, use this function.
(Default is logo appearing.)
[To undisplay]
Turn off the monitor's power by the Power Button on the control panel, then hold
down the Enter button once again and turn the power back on.
[To display again]
Turn off the monitor's power by the Power Button, then hold down the Enter button
once again and turn the power back on.
22
3. ScreenManager
English
4.
ADJUSTMENT
4-1. Screen Adjustment
NOTE
z Allow the LCD monitor to stabilize for at least 30 minutes before making image
adjustments.
The monitor displays the digital input image correctly based on its presetting data.
Analog Input
Screen adjustments for the LCD monitor should be used in suppressing screen
flickering and also for adjusting the screen to its proper position. There is only one
correct position for each display mode. It is also recommended to use the
ScreenManager function when first installing the display or whenever changing the
system. For convenience, an easy set-up Program installed on the utility disk to assist
in the setup procedure is provided.
Adjustment Procedure
1.
Press the Auto Adjustment Button on the control panel.
The message “Your setting will be lost, if you press again now.” appears and
remains on the screen for 5 seconds. While the message is on the screen, press
the Auto Adjustment Button again to automatically adjust the clock, phase,
screen position and resolution. If you do not wish to do adjust the screen, do
not press the Auto Adjustment Button again.
NOTE
z The Auto adjustment function is intended for use on the Macintosh and on
AT-compatible PC running Windows. It may not work properly in either of
the following cases.
When running an AT-compatible PC on MS-DOS (Not windows). The
background color for the “wall paper” or “desktop” pattern is set to black.
If the appropriate screen cannot be made by using the Auto
Adjustment Button, adjust the screen through the following
procedures. If the appropriate screen can be made, proceed to step 4.
4. ADJUSTMENT
23
English
2.
Run the “Screen adjustment program”.
Having read the “Readme.txt” file, run the “Screen Adjustment Program” in
the enclosed EIZO LCD Utility Disk. Step by step, adjustment is provided by
the wizard guide (If using the Windows, the program can be directly run from
the menu screen of the CD-ROM.) .
NOTE
z If the user's operating system has no utility disk (e.g. OS/2), we
recommend setting the desktop pattern to that as shown in the diagram on
the following.
3.
Adjust by using <Screen> menu in the ScreenManager.
(1)
Vertical bars appear on the screen
→
Use the <Clock> (p. 43) adjustment.
Select the <Clock> and eliminate the vertical bars by using the right and
left of the control buttons. Do not continuously press the control
buttons, as the adjustment value will change quickly and make it difficult
to locate the most suitable adjustment point.
If the horizontal flickering, blur or bars appear, proceed to “Phase”
adjustment as follows.
24
4. ADJUSTMENT
English
(2)
Horizontal flickering, blurring or bars appear on the screen.
→
Use the <Phase> (p. 44) adjustment.
Select the <Phase> and eliminate the horizontal flickering, blurring or
bars by using the right and left buttons.
NOTE
z Horizontal bars may not completely disappear from the screen
depending on the PC.
(3)
The screen position is not incorrect.
→
Use the <Position> adjustment.
The correct displayed position of the monitor is decided because the
number and the position of the pixels are fixed. The <Position>
adjustment moves the image to the correct position.
Select <Position> and adjust the position of the upper left corner of the
image by using the up, down, right and left buttons in order to align the
screen.
If vertical bars of distortion appear after finishing the <Position>
adjustment, return to <Clock> adjustment and repeat the previously
explained adjustment procedure (“Clock” → “Phase” → “Position”)
4. ADJUSTMENT
25
English
(4)
Screen image is smaller or larger than the actual screen images.
→
Use the <Resolution> adjustment.
Adjustment is needed when the input signal resolution and the resolution
now being displayed are different.
Select <Resolution> and confirm if the resolution now being displayed is
the same as the input resolution. If it is not, adjust the vertical resolution
using the up and down button and adjust the horizontal resolution using
the right and left buttons.
Smaller than the actual screen images.
Adjusted to actual screen
Larger than the actual screen images.
4.
Adjust the output signal range (Dynamic Range) of the signal.
→
Use the <Range Adjustment> (p. 44) of <Screen> menu.
This controls the level of output signal range to display the whole color
gradation (256 colors).
[Procedure]
Select <Range Adjustment> from <Screen> menu of the ScreenManager, the
message “Your setting will be lost, if you press AUTO button” appears. Press
the Auto Adjustment Button on the control panel while displaying the <Range
Adjustment> menu to automatically adjust the range. The screen blanks for a
moment and adjusts the color range to display the whole color gradation of the
current output signal.
26
4. ADJUSTMENT
English
4-2. Displaying Low Resolutions
The lower resolutions are enlarged to full screen automatically. Using the <Screen
Size> function in the <Others> menu enables to change the screen size.
1.
Enlarge the screen size when displaying a low resolution.
→
Select the <Screen Size>.
Select the <Screen Size> in the others menu and select the screen size by using
the up and down buttons.
Menu
Function
Full
Displays the picture on the screen in full, irrespective of the picture's
resolution. Since the vertical resolution and the horizontal resolution
are enlarged at different rates, some images may appear distorted.
Enlarged
Displays the picture on the screen in full, irrespective of the picture's
resolution. Since the vertical resolution and horizontal resolution are
enlarged at same rates, border may remain in either left/right side or
upper/bottom side of the screen.
Normal
Displays the picture at the actual screen resolution.
Example: Displaying 1024 × 768
2.
Full (Default Setting)
Enlarged
Normal
(1280 × 1024)
(1280 × 960)
(1024 × 768)
Smooth the blurred texts of the enlarged screen.
→
Switch the <Smoothing> setting.
Select the suitable level from 1 - 5 (Soft - Sharp).
Select <Smoothing> in the <Screen> menu and adjust by using the right and left
buttons.
NOTE
z <Smoothing> is disabled when the screen is displayed in the following
resolutions.
*1280 × 1024
*The image size is doubled both in horizontally and vertically to (i.e. 1280 ×
960 enlarged from 640 × 480) provide clear focus which does not require
this function.
4. ADJUSTMENT
27
English
3.
Set the brightness of the black area surrounding the displayed
image.
→
Set the <Border Intensity>.
In the <Enlarge> mode or <Full Screen> mode, the outer area (border) is usually
black.
Select <Border Intensity> in the <Others> menu and adjust by using the right
and left buttons.
Border
28
4. ADJUSTMENT
English
4-3. Color Adjustment
Color adjustments are provided in ScreenManager <Color Management> menu.
To customize monitor color, select <Custom> through the <Color Mode>.
To configure monitor color to sRGB standard, select <sRGB> through the <Color
Mode>.
Color mode can also be switched to other if pressing Mode button of the control
panel.
In the analog input, perform the “Range Adjustment” (p. 26) before making
the color adjustments.
NOTE
z Allow the LCD monitor to stabilize for at least 30 minutes before making image
adjustments.
z Performing the <Reset> of the <Color> menu returns the color settings of the
selected mode to the default settings.
z The values shown in percentages represent the current level within the specific
adjustment. They are available only as a reference tool. (To create a uniform
white or black screen, the percentages for each will probably not be the same.)
<Custom> Mode - customizing monitor color
Adjustment Contents
0
Menu
Brightness
Function Descriptions
To set the brightness of the
screen
Adjustable range
0 ~ 100 %
NOTE
z
Contrast
The values shown in the percentage are available only as a reference
tool.
To adjust the screen gradation
higher or lower
0 ~ 100 %
NOTE
z
The values shown in the percentage are available only as a reference
tool.
4. ADJUSTMENT
29
English
Menu
Temperature
(p. 44)
Function Descriptions
To set the color temperature
Adjustable range
4000 ~ 10000 K
in 500 K increments (including 9300 K).
NOTE
Saturation
z
Setting the value to “Off” presents the natural color temperature of the
panel.
z
The values shown in the Kelvin are available only as a reference tool.
z
Setting the temperature under 4000 K or over 10000 K invalidates the color
temperature setting. (The color temperature's setting turns “Off”.)
To change the saturation
-16 ~ 16
Setting the minimum level (-16) turns the
image to the monochrome.
NOTE
z
Hue
Using <Saturation> adjustment may not obtain proper tone
reproduction.
To change the flesh color, etc. -20 ~ 20
NOTE
z
Gain
Using <Hue> adjustment may not obtain proper tone reproduction.
To change each color
(red, green and blue)
0 ~ 100%
By adjusting the red, green and blue color
tones for each mode, custom colors can be
defined. Display a white or gray
background image and adjust the <Gain>.
NOTE
Reset
z
The values shown in the percentage are available only as a reference
tool.
z
Setting the <Temperature> (p. 44) invalidates the <Gain> adjustment.
<Gain> setting returns to the default.
To return the color settings of
the selected mode to the
default settings
Select the “Reset”.
<sRGB> Mode
Adjustment Contents
0
Menu
Brightness
30
Function Descriptions
To set the brightness of the
screen
4. ADJUSTMENT
Adjustable range
0 ~ 100 %
English
4-4. Power-save Setup
The <PowerManager> menu in the ScreenManager enables to set the power-save
setup.
NOTE
z Do your part to conserve energy, turn off the monitor when you are finished using
it. Disconnecting the monitor from the power supply is recommended to save
energy completely.
z Even if the monitor is in a power saving mode, USB compliant devices function
when they are connected to the monitor's USB (both the upstream and the
downstream ports). Therefore, power consumption of the monitor will change
according to the connected devices even if the monitor is in a power saving
mode.
Analog Input
This monitor complies with the <VESA DPMS> (p. 44) standard and adopts a power
saving method, <EIZO MPMS> (p. 43), which works with a blank screen (totally
black screen) like “Blank Screen” ScreenSaver software.
To use the PC's Power Saving System (VESA DPMS )
[Procedure]
(1)
Set the PC's power saving settings.
(2)
Select “VESA DPMS” in the <PowerManager> menu.
[Power Saving System]
Power saving
PC
Monitor
Power Indicator
Operation
The screen is displayed
Blue
Power saving
Yellow
STAND-BY
SUSPEND
OFF
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen.
4. ADJUSTMENT
31
English
To set the Power Save with ScreenSaver (EIZO MPMS) Software.
[Procedure]
(1)
Set the PC's appropriate ScreenSaver settings or blank the screen (totally black
screen).
(2)
Select “EIZO MPMS” in the <PowerManager> menu.
[Power Saving System]
PC
Operation
Blank the screen
(ScreenSaver or Macintosh Energy Saver)
Monitor
Power Indicator
The screen is displayed
Blue
Power saving
Yellow
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen.
NOTE
z EIZO MPMS should be used with Macintosh “EnergySaver”.
Digital Input
This monitor complies with the DVI DMPM (p. 43).
[Procedure]
(1)
Set the PC's power saving settings.
(2)
Select “DVI DMPM” in the <PowerManager> menu.
[Power Saving System]
PC
On
Monitor
Power Indicator
The screen is displayed
Blue
Power saving
Yellow
Power saving*1
Flashing yellow
(2 times for each)
Power saving
Off mode
*1 Power saving through the PC's off mode is only supported when “Manual” is selected on
the ScreenManager's <Input Priority>.
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen.
Power on the PC to return a normal screen from the Off mode of the PC.
32
4. ADJUSTMENT
English
5.
MAKING USE OF USB
(UNIVERSAL SERIAL BUS)
This monitor provides a hub which supports the USB standard. When connecting to
a USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.
Required system environment
z PC equipped with USB ports or another USB hub connected to the USB compliant PC
z Windows 98/Me/2000/XP // Mac OS 8.5.1 or later
z EIZO USB Cable (MD-C93 enclosed)
NOTE
z The USB hub function may not work properly depending on the PC, OS or
peripherals. Please consult the manufacturer of each device about the USB
support.
z Using the USB Rev. 2,0 compatible PC or peripherals is recommended.
z When the monitor is not on, the peripherals connected to the downstream ports
will not operate.
z If the monitor is in the power saving mode, or if the monitor is connected to the
power outlet with the monitor turned off, all the devices connected to the USB
ports (upstream and downstream) work. Therefore, power consumption of the
monitor varies with connected devices even in the power saving mode.
z The followings are procedures for the Windows 98/Me/2000/XP and Mac OS.
Connecting to the USB HUB
1.
Connect the monitor to the PC with the signal cable (See page 13)
first, then turn on the PC.
2.
Connect the upstream port of the monitor to the downstream port
of the USB compliant PC or another hub by using the USB cable.
Upstream Port
Upstream port:
Connect the USB compliant PC
or another hub using the USB
cable.
To Downstream Ports of the PC or
Another Hub
After connecting the USB cable, the USB function can be set up automatically.
5. MAKING USE OF USB (Universal Serial Bus)
33
English
3.
After setting up, the monitor's USB hub is available for
connecting USB compliant peripherals to the downstream ports
of the monitor.
Connecting Examples
Scanner
Monitor
PC
Mouse
Keyboard
Downstream Ports
Downstream ports:
Connect the cables from USB
compliant peripherals such as
a mouse, keyboard, etc.
Scanner
Keyboard
34
5. MAKING USE OF USB (Universal Serial Bus)
English
6.
ATTACHING AN ARM
The LCD monitor can be used with an arm by removing the tilt stand and attaching
the arm or stand to the LCD monitor. Use an arm or stand of EIZO option.
NOTE
z When attaching an arm or stand, follow the instructions of their user’s manual.
z When using another manufacturer’s arm or stand, confirm the following in
advance and select one conforming to the VESA standard. Use the M4 × 12
screws supplied with this monitor.
– Clearance between the screw holes: 100 mm × 100 mm
– Thickness of plate: 2.6 mm
– Strong enough to support weight of the monitor unit (except the stand) and
attachments such as cables.
z Attach an arm or stand to meet the following tilt angles of the monitor.
– Up 60 degrees, down 45 degrees
z Connect the cables after attaching an arm.
Setup Procedure
1.
Lay the LCD monitor on a soft cloth spread over on a stable
surface with the panel surface facing down.
2.
Remove the stand. (Prepare a screwdriver.)
Unscrew the four screws securing the unit and the stand with the screwdriver.
3.
Attach the monitor to the arm or stand.
Secure the monitor to the arm or stand using the screws specified in the user’s
manual of the arm or stand.
Arm-stand
6. ATTACHING AN ARM
35
English
7.
TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO dealer.
z No picture problems → See No.1 ~ No.2
z Imaging problems → See No.3 ~ No.13
z Other problems → See No.14 ~ No.16
z USB problems → See No.17 ~ No.18
Problems
1.
No picture
z
Indicator status: Off
Points to check with Possible Solutions
†
Check that the power cord is correctly connected.
If the problem persists, turn off the monitor power
for a few minutes, then turn it back on and try
again.
† Try pressing the Power Button.
z
Indicator status: Blue
† Check the “Gain” setting.
z
Indicator status: Yellow
† Switch the signal input by pressing the Input
Signal Selection Button on the front control panel.
† Try pressing a key on the keyboard, or clicking
the mouse. (p. 31)
† Try turning the PC on.
z
2.
Indicator status: Flashing
Yellow (twice for each)
Error messages shown below
will remain on the screen for 40
seconds.
† Try turning the PC on.
These messages appear when the signal is not
inputted correctly, even if the monitor functions properly.
† When the image is displayed correctly after a
short time, there is no problem with the monitor.
(Some PCs do not output the signal soon after
powering on.)
† Check that the PC is turned ON.
† Check that the signal cable is properly
connected to the PC or graphics board.
† Switch the signal input by pressing the Input
Signal Selection Button on the control panel.
z
The signal frequency is out
of range. Error signal
frequency will be displayed
in red.
(Example)
36
7. TROUBLESHOOTING
† Use the graphics board’s utility software to
change the frequency setting. (Refer to the
manual of the graphics board.)
English
3.
Problems
Points to check with Possible Solutions
Display position is incorrect.
† Adjust the image position using the <Position>.
(p. 25)
† If the problem persists, use the graphics
board’s utility software to change the display
position if available.
† Adjust the resolution using the <Resolution>.
(p. 26)
4.
Screen image is smaller or larger
than the actual screen images.
5.
Vertical bars of distortion appear. † Decrease the vertical bars using the <Clock>.
(p. 24)
6.
Horizontal bars of distortion
appear.
† Decrease the horizontal bars using the
<Phase>. (p. 25)
7.
Letters and lines appear blurred.
† Adjust the blurred lines using <Smoothing>
(p. 27)
8.
Distortion appears like the figure
below.
† This happens when both composite (X-OR)
input signal and separate vertical
synchronizing signal are input. Please select
one of the two.
9.
The screen is too bright or too
dark.
† Adjust the <Brightness> (The backlight of the
LCD monitor has a fixed life span. When the
screen becomes dark or begins to flicker,
please contact your dealer.)
10. Afterimages appear.
† Do you use the screen saver or timer when
displaying the same image for extended
periods of time?
† Afterimages are particular to LCD monitors.
Avoid displaying the same image for extended
periods of time.
11. The screen has defective pixels
(e.g. slightly light or dark).
† This is due to the characteristics of the panel
itself and not the LCD product.
12. Fingerprints remain on the screen. † Leaving the screen white may solve the problem.
7. TROUBLESHOOTING
37
English
Problems
Points to check with Possible Solutions
13. The noise appears on the
screen.
† Change the mode in <Signal Filter> in the
<Screen> menu.
14. The <Smoothing> cannot be
selected.
† <Smoothing> is disabled when the screen is
displayed in the 1280 ×1024.
† The image size is doubled both in horizontally
and vertically to (i.e. 1280 × 960 enlarged from
640 × 480) provide clear focus which does not
require this function.
15. The Main menu of
ScreenManager does not
operate.
† The adjustment lock is probably on. To unlock:
turn the LCD monitor off. Then, while pressing
the Auto Adjustment Button, turn the power on.
(p. 21)
16. The Auto Adjustment Button
does not operate.
† The Auto Adjustment Button does not function
if digital signal inputs.
† The adjustment lock is probably on. To unlock:
turn the LCD monitor off. Then, while pressing
the Auto Adjustment Button, turn the power on.
(p. 21)
17. USB function cannot be setup.
† Check that the USB cable is correctly
connected.
† Check that the PC and OS are USB compliant.
(For verification of USB support, consult the
manufacturer of each system.)
† Check the PC’s BIOS setting for USB. (For
details, refer to the manual of the PC).
18. PC is hung up. / The peripherals
connected to the downstream
ports do not operate.
† Check that the USB cable is correctly connected.
† Check the downstream ports by connecting the
peripherals to other downstream ports. If the
problem is solved by doing this, contact an
EIZO dealer. (For details, refer to the manual of
the PC.)
† Try executing the following method.
z
Restarting the PC - Restarting the PC
z
Connecting the PC and peripherals directly
If the problem is solved by doing this, contact
an EIZO dealer.
38
7. TROUBLESHOOTING
English
8.
CLEANING
Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.
NOTE
z Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),
abrasive cleaners, or other strong solvents, as these may cause damage to the
cabinet or LCD panel.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to
the manual of the PC.)
LCD Panel
z The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.
z If necessary, stubborn stains can be removed by moistening part of a cloth with
water to enhance its cleaning power.
8. CLEANING
39
English
9.
SPECIFICATIONS
LCD Panel
48 cm (19 inch), TFT color LCD panel with Anti-Glare Hard
Coating, Viewing Angle: Horizontal: 178°, Vertical: 178°
(CR ≥ 10)
Dot Pitch
0.294 mm
Horizontal Scan Frequency
Analog: 30 ~ 82 kHz (Automatic)
Digital: 30 ~ 65 kHz
Vertical Scan Frequency
Analog: 49 ~ 86 Hz (Automatic) (1280 × 1024: 49 ~ 76 Hz)
Digital: 59 ~ 61 Hz, (VGA TEXT: 69 ~ 71 Hz)
Resolution
1280 dots × 1024 lines
Dot Clock (Max.)
Analog: 135 MHz
Digital: 108 MHz
Display Colors
16 million colors (max)
Display Area
376 mm (H) × 301 mm (V) (14.8” (H) × 11.9” (V))
Power Supply
100-120/200-240 VAC ±10%, 50/60 Hz, 0.8 /0.5 A
Power Consumption
Min.: 40 W
Max.: 50 W (with USB hub)
Power Saving Mode: Less than 2 W (for single signal input
without USB)
Input Connector
DVI-I × 2 connectors
Analog Input Signal (Sync)
a) Separate, TTL, Positive/Negative
b) Composite, TTL, Positive/Negative
c) Sync on Green, 0.3 Vp-p, Negative
40
Analog Input Signal (Video)
0.7 Vp-p / 75 Ω Positive
Input Signal (Digital)
TMDS (Single Link)
Signal registration
45 (Factory preset: 25)
Plug & Play
VESA DDC 2B
Dimensions
404 mm (W) × 406 ~ 506 mm (H) × 205 mm (D)
(15.9” (W) × 16” ~ 19.9” (H) × 8.1” (D)
Dimensions (without stand)
404mm (W) × 333mm (H) × 60mm (D)
(15.9” (W) × 13.1” (H) × 2.36” (D))
Weight
6.8kg (15 lbs.)
Weight (without stand)
4.8kg (10.6 lbs.)
Temperature
Operating: 0°C ~ 35°C (32°F ~ 95°F)
Storage: -20°C ~ 60°C (-4°F ~ 140°F)
Humidity 30% to 80% R.H. Non-condensing
USB standard
USB Specification Revision 2.0
USB port
Upstream port × 1, Downstream port × 2
Communication Speed
480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Power Supply
Downstream: 500 mA for each (Max.)
9. SPECIFICATIONS
English
„ Default settings
Brightness
Analog input
Digital input
100%
100%
Smoothing
3
Color Mode
Custom
PowerManager
VESA DPMS
DVI DMPM
Screen Size
Full
Input Priority
1
Off Timer
Menu Settings
Disable
Menu Size: Normal, Menu Off Timer: 45 seconds
Beep
On
Language
English
„ Beeper settings
Short beep
ScreenManager item selected.
ScreenManager parameter adjusted to minimum or
maximum limit.
Input Signal Selection Button pressed.
Long beep
Auto Adjustment Button pressed.
ScreenManager data-save executed.
4 short beeps
Monitor not connected correctly.
PC turned off.
Monitor received unsupported signal frequency.
2 short beeps every 15 sec.
Monitor is in the advance notice mode of the Off Timer.
The power will be off within fifteen minutes.
„ Dimensions
mm (inch)
9. SPECIFICATIONS
41
English
„ Pin Assignment
DVI-I Connector
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
C1
C2
C3 C4
C5
Pin
No.
Signal
Pin
No.
Signal
Pin
No.
Signal
1
TMDS Data 2-
11
TMDS Data 1/3 Shield
21
NC
2
TMDS Data 2+
12
NC
22
TMDS Clock shield
3
TMDS Data 2/4 Shield
13
NC
23
TMDS Clock+
4
NC*
14
+5V Power
24
TMDS Clock-
5
NC
15
Ground (return for +5V,
Hsync and Vsync)
C1
Analog Red
6
DDC Clock (SCL)
16
Hot Plug Detect
C2
Analog Green
7
DDC Data (SDA)
17
TMDS Data 0-
C3
Analog Blue
8
Analog Vertical Sync
18
TMDS Data 0+
C4
Analog Horizontal Sync
9
TMDS Data 1-
19
TMDS Data0/5 Shield
C5
Analog Ground
(analog R, G, & B return)
10
TMDS Data 1+
20
NC
(*NC: No Connection)
USB Port
Upstream
Series B
Downstream
Series A
No.
Signal
Signal
1
VCC
Cable power
2
- Data
Serial data
3
+ Data
Serial data
4
Ground
Cable Ground
„ Optional
42
Sound Unit for LCD Monitor
EIZO i·Sound L3
Cleaning kit
EIZO ScreenCleaner
9. SPECIFICATIONS
English
10. GLOSSARY
Clock
With the analog input signal display, the analog signal is converted to a digital
signal by the LCD circuitry. To convert the signal correctly, the LCD monitor
needs to produce the same number clock pulse as the dot clock of the graphics
system. When the clock pulse is not correctly set, some vertical bars of distortion
are displayed on the screen.
DVI
(Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly
without loss with the signal transition method “TMDS”.
There are two kinds of DVI connectors. One is DVI-D connector for digital signal
input only. The other is DVI-I connector for both digital and analog signal inputs.
DVI DMPM
(DVI Digital Monitor Power Management)
The Power management system for the digital interface. The “Monitor ON”
status (operation mode) and the “Active Off” status (power-saving mode) are
indispensable for the DVI-DMPM as the monitor's power mode.
EIZO MPMS
(EIZO Monitor PowerManager Signaling)
EIZO MPMS, “EIZO Monitor PowerManager Signaling” also enables power
saving on the monitor side. EIZO MPMS recognizes video signals from the PC
when the PC is in a power saving mode and reduces energy consumption of the
monitor.
Gain Adjustment
Adjusts each color parameter for red, green and blue. The color of the LCD
monitor is displayed through the color filter of the LCD panel. Red, green and
blue are the three primary colors. The colors on the monitor are displayed by
combining these three colors. The color tone can change by adjusting the
illumination amount passed through each color's filter.
Phase
The phase adjustment decides the sampling timing point for converting the analog
input signal to a digital signal. Adjusting the phase after the clock adjustment will
produce a clear screen.
10. GLOSSARY
43
English
Range Adjustment
The Range Adjustment controls the level of output signal range to display the
whole color gradation.
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated
to form the screen image. This products' display panel consists of 1280 horizontal
pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are
displayed as a full screen.
sRGB (Standard RGB)
“International Standard for Red, Green and Blue color space”
A color space was defined with the aim of the color matching between applications
and hardware devices, such as monitors, scanners, printers and digital cameras. As
a standard default space, sRGB allows Internet users to closely match colors.
Temperature
Color temperature is a method to measure the white color tone, generally indicated
in degrees Kelvin. At high temperatures the white tone appears somewhat blue,
while at lower temperatures it appears somewhat red. Computer monitors
generally give best performance at high temperature settings.
5000K: Often used in printing industry.
6500K: Good for video-image display.
9300K: Default setting for your EIZO monitor.
TMDS
(Transition Minimized Differential Signaling)
A signal transition method for the digital interface
VESA DPMS
(Video Electronics Standards Association - Display Power Management Signaling)
The acronym VESA stands for “Video Electronics Standards Association” and
DPMS stands for “Display Power Management Signaling”. DPMS is a
communication standard that PCs and graphics boards use to implement power
savings on the monitor side.
44
10. GLOSSARY
APPENDIX/ANHANG/ANNEXE
Preset Timing Chart for Analog input
Timing-Übersichten für Analog Eingang
Synchronisation des Signaux pour Analog numerique
Based on the signal diagram shown below factory presets have been registered in the
monitor's microprocessor.
Der integrierte Mikroprozessor des Monitors unterstützt werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
Signaux ont été enregistrés en usine dans le microprocesseur du moniteur,
conformément au diagramme de synchronisation ci-dessous.
i
Sync Polarity
Frequencies
Dot Clock
MHz
H
V
H kHz
V Hz
VGA
640 × 480 @ 60 Hz
25.2
Nega.
Nega.
31.5
60.0
VGA TEXT
720 × 400 @ 70 Hz
28.3
Nega.
Posi.
31.5
70.1
Macintosh
640 × 480 @ 67 Hz
30.2
Nega.
Nega.
35.0
66.7
Macintosh
832 × 624 @ 75 Hz
57.3
Posi.
Posi.
49.7
74.6
Macintosh
1152 × 870 @ 75 Hz
100.0
Nega.
Nega.
68.7
75.1
Macintosh
1280 × 960 @ 75 Hz
126.2
Posi.
Posi.
74.8
74.8
VESA
640 × 480 @ 72 Hz
31.5
Nega.
Nega.
37.9
72.8
VESA
640 × 480 @ 75 Hz
31.5
Nega.
Nega.
37.5
75.0
VESA
640 × 480 @ 85 Hz
36.0
Nega.
Nega.
43.3
85.0
VESA
800 × 600 @ 56 Hz
36.0
Posi.
Posi.
35.2
56.3
VESA
800 × 600 @ 60 Hz
40.0
Posi.
Posi.
37.9
60.3
VESA
800 × 600 @ 72 Hz
50.0
Posi.
Posi.
48.1
72.2
VESA
800 × 600 @ 75 Hz
49.5
Posi.
Posi.
46.9
75.0
Mode
APPENDIX/ANHANG/ANNEXE
Sync Polarity
Frequencies
Dot Clock
MHz
H
V
H kHz
V Hz
VESA
800 × 600 @ 85 Hz
56.3
Posi.
Posi.
53.7
85.1
VESA
1024 × 768 @ 60 Hz
65.0
Nega.
Nega.
48.4
60.0
VESA
1024 × 768 @ 70 Hz
75.0
Nega.
Nega.
56.5
70.1
VESA
1024 × 768 @ 75 Hz
78.8
Posi.
Posi.
60.0
75.0
VESA
1024 × 768 @ 85 Hz
94.5
Posi.
Posi.
68.7
85.0
VESA
1152 × 864 @ 75 Hz
108.0
Posi.
Posi.
67.5
75.0
WS
1152 × 900 @ 66 Hz
94.2
Composite Sync, Nega
62.0
66.1
WS
1152 × 900 @ 76 Hz
107.5
Composite Sync, Nega
71.9
76.2
VESA
1280 × 960 @ 60 Hz
108.0
Posi.
Posi.
60.0
60.0
VESA
1280 × 1024 @ 60 Hz
108.0
Posi.
Posi.
64.0
60.0
VESA
1280 × 1024 @ 75 Hz
135.0
Posi.
Posi.
80.0
75.0
Mode
ii
APPENDIX/ANHANG/ANNEXE
[Applicable to gray cabinet version only.]
Congratulations!
The display you have just purchased carries the TCO'03 Displays
label. This means that your display is designed, manufactured
and tested according to some of the strictest quality and
environmental requirements in the world. This makes for a high
performance product, designed with the user in focus that also
minimizes the Impact on our natural environment.
Some of the features of the TCO'03 Display requirements:
Ergonomics
z Good visual ergonomics and image quality in order to improve the working
environment for the user and to reduce sight and strain problems. Important
parameters are luminance, contrast, resolution, reflectance, colour rendition and
image stability.
Energy
z Energy-saving mode after a certain time - beneficial both for the user and environment
z Electrical safety
z Emissions
Electromagnetic fields
z Noise emissions
Ecology
z The products must be prepared for recycling and the manufacturer must have a
certified environmental management system such as EMAS or ISO 14000
z Restrictions on
 chlorinated and brominated flame retardants and polymers
 heavy metals such as cadmium, mercury and lead.
The requirements includes in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the
end of the 1980s TCO has been involved in influencing the development of IT equipment in a
more user-friendly direction. Our labeling system with displays in 1992 and is now requested
by users and IT-manufacturers all over the world.
For more information, please visit
www.tcodevelopment.com
[Applicable to black cabinet version only]
Congratulations!
You have just purchased a TCO'99 approved and labelled
product! Your choice has provided you with a product developed
for professional use. Your purchase has also contributed to
reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging
the adaptation of goods and services to the environment. The main problem, as far as
computers and other electronics equipment are concerned, is that environmentally harmful
substances are used both in the products and during their manufacture. Since it is not so far
possible to satisfactorily recycle the majority of electronics equipment, most of these potentially
damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments.
Since all methods of electricity generation have a negative effect on the environment (e.g. acidic
and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics
equipment in offices is often left running continuously and thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO'99 scheme which provides for international
and environmental labelling of personal computers. The labelling scheme was developed as a
joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens
Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability,
emission of electric and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among
other things. The product must be prepared for recycling and the manufacturer is obliged to
have an environmental policy which must be adhered to in each country where the company
implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain
period of inactivity, shall reduce its power consumption to a lower level in one or more stages.
The length of time to reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the
reduction of electric and magnetic fields, physical and visual ergonomics and good usability.
You will find a brief summary of the environmental requirements met by this product on the
right. The complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO'99 approved and labelled products may also be
obtained via the Internet, using the address: http://www.tco-info.com/
Environmental Requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings.
Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in
a computer casing can consist of flame retardant substances. Most flame retardants contain
bromine or chloride, and those flame retardants are chemically related to another group of
environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and
the PCBs are suspected of giving rise to severe health effects, including reproductive damage
in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants
have been found in human blood and researchers fear that disturbances in foetus
development may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25
grams must not contain flame retardants with organically bound bromine or chlorine. Flame
retardants are allowed in the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses.
The relevant TCO'99 requirement states that batteries, the colour-generating layers of
display screens and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system
and is toxic in high doses.
The relevant TCO'99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components
associated with the labelled unit.
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during
the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing
printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks
of skin cancer (malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages
the nervous system and in higher doses, causes lead poisoning.
The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet
been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are haevy metals which are Bio-accumulative.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem
Videosignal, 1280 × 1024 RGB analog, 0,7 Vp-p und mindestens 60,0 Hz
Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen
empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum
Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter
anderer Schwenkarm installiert werden. Bei der Auswahl des Schwenkarms sind die
nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a) Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des
Gewichtes vom Bildschirmgerät und des spezifizierten Zubehörs besitzen. Das Gewicht
des Bildschirmgerätes und des Zubehörs sind in der zugehörenden Bedienungsanleitung
angegeben.
b) Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der
Bildschirmanzeige nicht höher als die Augenhöhe eines Benutzers in sitzender Position
ist.
c) Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart
erfolgen, daß die Höhe der Bildschirmmitte über dem Boden zwischen 135 – 150 cm
beträgt.
d) Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max.
vorwärts: 5°, min. nach hinten = 5°).
e) Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max.
±180°). Der maximale Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g) Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen
(seidenmatt).
h) Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der
normalen aufrechten Position kippsicher sein.
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
Recycling Information for customers in EU:
All recycling information is placed in the following websites.
Recycling-Information für Kunden in Europa:
Alle Informationen zum Thema Recycling finden Sie auf den folgenden Websites:
Informations sur le recyclage pour les clients dans l’UE:
Vous trouverez toutes les informations sur le recyclage dans les sites Web suivants:
Återvinningsinformation för kunder i EU:
All information om återvinning finns på följande webbsidor:
http://www.swico.ch
http://www.eizo.de
http://www.eizo.se
Recycling Information for customers in USA:
All recycling information is placed in the EIZO Nanao Technologies, Inc’s website.
http://www.eizo.com
Download PDF